Download Service Manual

Service
Manual
DEH-3130R/X1N/EW
ORDER NO.
CRT2418
HIGH POWER CD PLAYER WITH RDS TUNER
DEH-3130R
DEH-3100R-B
X1N/EW
X1N/EW
DEH-3100R
X1N/EW
- This service manual should be used together with the following manual(s):
Model No.
CX-958
Order No.
CRT2423
Mech. Module Remarks
S8.1
CD Mech. Module:Circuit Description, Mech.Description, Disassembly
CONTENTS
1.
2.
3.
4.
5.
6.
SAFETY INFORMATION ............................................2
EXPLODED VIEWS AND PARTS LIST .......................3
BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...10
PCB CONNECTION DIAGRAM ................................28
ELECTRICAL PARTS LIST ........................................38
ADJUSTMENT..........................................................44
7. GENERAL INFORMATION .......................................48
7.1 DIAGNOSIS ........................................................48
7.1.1 TEST MODE ..............................................48
7.1.2 DISASSEMBLY .........................................52
7.2 PARTS .................................................................56
7.2.1 IC................................................................56
7.2.2 DISPLAY ....................................................63
8. OPERATIONS AND SPECIFICATIONS.....................64
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A.
PIONEER ELECTRONIC [EUROPE] N.V. Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936
C PIONEER CORPORATION 1999
K-ZZD. OCT. 1999 Printed in Japan
DEH-3130R,3100R-B,3100R
- CD Player Service Precautions
1. For pickup unit(CXX1285) handling, please refer
to"Disassembly"(see page 52).
During replacement, handling precautions shall be
taken to prevent an electrostatic discharge(protection
by a short pin).
2. During disassembly, be sure to turn the power off
since an internal IC might be destroyed when a connector is plugged or unplugged.
3. Please checking the grating after changing the service pickup unit(see page 44).
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do so
and refer the repair to a qualified service technician.
1. Safety Precautions for those who Service this Unit.
• When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
Caution:
1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
2. A “CLASS 1 LASER PRODUCT” label is affixed to the
bottom of the player.
3. The triangular label is attached to the mechanism
unit frame.
CLASS 1
LASER PRODUCT
4. Specifications of Laser Diode
Specifications of laser radiation fields to which human access is possible during service.
Wavelength
= 800 nanometers
2
DEH-3130R,3100R-B,3100R
2. EXPLODED VIEWS AND PARTS LIST
2.1 PACKING
2
4
3
6
5
9
12
11
1
7
8
13
10
NOTE:
- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.
- Screws adjacent to ∇ mark on the product are used for disassembly.
(1) PACKING SECTION PARTS LIST
Mark No. Description
*
*
1
2
3
4
5
6
7
8-1
8-2
8-3
Part No.
Cord Assy
Accessory Assy
Screw
Handle
Bush
CDE6238
CEA2397
CBA1002
CNC5395
CNV3930
Polyethylene Bag
Polyethylene Bag
Owner’s Manual
Owner’s Manual
Owner’s Manual
E36-615
CEG-162
CRD3073
CRD3074
CRD3075
Mark No. Description
*
*
8-4
8-5
8-6
8-7
9
10
11
12
13
Part No.
Installation Manual
Passport
Warranty Card
Polyethylene Bag
Case Assy
CRD3076
CRY1013
CRY1157
CEG1116
CXB3520
Carton
Contain Box
Protector
Protector
See Contrast table(2)
See Contrast table(2)
CHP2251
CHP2252
3
DEH-3130R,3100R-B,3100R
(2) CONTRAST TABLE
DEH-3130R/X1N/EW, DEH-3100R-B/X1N/EW and DEH-3100R/X1N/EW are constructed the same except
for the following:
Mark No. Symbol and Description DEH-3130R/X1N/EW
10 Carton
CHG3882
11 Contain Box
CHL3882
Part No.
DEH-3100R-B/X1N/EW DEH-3100R/X1N/EW
CHG3883
CHG3881
CHL3883
CHL3881
- Owner's Manual, Installation Manual
Model
DEH-3130R/X1N/EW
DEH-3100R-B/X1N/EW
DEH-3100R/X1N/EW
4
Part No.
CRD3073
CRD3074
CRD3075
CRD3076
Language
English, Spanish
German, French
Italian, Dutch
English, Spanish, German, French, Italian, Dutch
DEH-3130R,3100R-B,3100R
2.2 EXTERIOR
5
DEH-3130R,3100R-B,3100R
(1) EXTERIOR SECTION PARTS LIST
Mark No. Description
6
Mark No. Description
Part No.
Screw
Screw
Screw
Screw
•••••
BMZ26P120FMC
BSZ26P060FMC
BSZ30P060FMC
BSZ30P120FMC
46
47
48
49
50
Spring
Spring
Bracket
Holder
Cover
CBH2367
CBH2208
CNC6791
CNC8042
CNM6276
6
7
8
9
10
IC(IC551)
Cable
Cord Assy
Resistor
Transistor(Q981,991)
PAL005A
CDE6160
CDE6238
RS1/2PMF102J
2SD2396
51
52
53
54
55
Panel
Arm
Arm
Arm
Screw
See Contrast table(2)
11
12
13
14
15
Cap
Fuse(10A)
Holder
Cover
Spacer
CNS1472
CEK1136
CNC6798
CNC8367
CNM4913
56
57
58
59
60
Case Unit
•••••
•••••
•••••
•••••
16
17
18
19
20
Earth Plate
Insulator
Insulator
•••••
•••••
CNC8368
CNM6006
CNM6224
61
62
63
64
65
Detach Grille Assy
Screw
Button(DETACH)
Button(1-6)
Button(SOURCE)
21
22
23
24
25
Tuner Amp Unit
Screw
Screw
Screw
Connector(CN551)
CWM6841
ASZ26P080FMC
BPZ26P080FMC
BSZ26P160FMC
CDE5996
66
67
68
69
70
Button(+)
Button(-)
Button(F)
Button(A)
Button(EQ)
26
27
28
29
30
Antenna Cable(CN502)
Pin Jack(CN431)
Terminal(CN501)
Connector(CN951)
Connector(CN681)
CDH1254
CKB1028
CKF1059
CKM1299
CKS2227
71
72
73
74
75
Button(EJECT)
Button(BAND)
Spring
Cover
Lighting Conductor
31
32
33
34
35
•••••
Connector(CN651)
•••••
Holder
Holder
Lighting Conductor
Housing
Keyboard Unit
LCD
Connector(CN1801)
CNV5910
CNV5918
CNC7533
CNC8130
76
77
78
79
80
36
37
38
39
40
Holder
Holder
Insulator
Heat Sink
FM/AM Tuner Unit
CNC8041
CNC8043
CNM5967
CNR1506
CWE1500
81
82
83
84
85
Holder
Sheet
Lighting Conductor
Connector
Grille Sub Assy
CNC8468
CNM6435
CNV5908
CNV6051
41
42
43
44
45
Holder
Chassis Unit
•••••
Button
Spring
CNC7532
86 CD Mechanism Module(S8.1) CXK5201
87 Screw
ISS26P055FUC
1
2
3
4
5
*
Part No.
CKS3581
See Contrast table(2)
CAC4836
CBH1835
CNV4692
CNV4728
CNV5576
IMS20P030FZK
CXB4033
See Contrast table(2)
BPZ20P100FZK
See Contrast table(2)
CAC6239
CAC6241
See Contrast table(2)
See Contrast table(2)
See Contrast table(2)
See Contrast table(2)
CAC6247
CAC6248
See Contrast table(2)
CBH2210
See Contrast table(2)
CNV5909
See Contrast table(2)
See Contrast table(2)
CKS3580
See Contrast table(2)
DEH-3130R,3100R-B,3100R
(2) CONTRAST TABLE
DEH-3130R/X1N/EW, DEH-3100R-B/X1N/EW and DEH-3100R/X1N/EW are constructed the same except
for the following:
Mark No.
42
51
61
63
66
67
68
69
72
74
Symbol and Description
Chassis Unit
Panel
Detach Grille Assy
Button(DETACH)
Button(+)
DEH-3130R/X1N/EW
CXB4711
CNS5340
CXB4722
CAC5929
CAC6559
Part No.
DEH-3100R-B/X1N/EW
CXB4709
CNS5188
CXB4723
CAC5789
CAC6242
DEH-3100R/X1N/EW
CXB4710
CNS5188
CXB4721
CAC5789
CAC6242
Button(-)
Button(F)
Button(A)
Button(BAND)
Cover
CAC6560
CAC6561
CAC6562
CAC6578
CAC5794
CAC6243
CAC6244
CAC6245
CAC6249
CNS5622
CAC6243
CAC6244
CAC6245
CAC6249
CNS5622
CWM6796
CAW1570
CXB5251
CWM6797
CAW1572
CXB5252
CWM6795
CAW1570
CXB5250
78 Keyboard Unit
79 LCD
85 Grille Sub Assy
7
DEH-3130R,3100R-B,3100R
2.3 CD MECHANISM MODULE
8
DEH-3130R,3100R-B,3100R
- CD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description
Part No.
Mark No. Description
Part No.
Control Unit
Connector(CN802)
Connector(CN801)
Connector(CN701)
Connector(CN101)
CWX2411
CKS2192
CKS2193
CKS2773
CKS3486
46
47
48
49
50
•••••
Ball
Belt
Roller
Arm
CNR1189
CNT1086
CNV4509
CNV6037
6
7
8
9
10
Screw
Screw
Screw(M2x3)
Screw(M2x5)
Screw
BMZ20P030FMC
BSZ20P040FMC
CBA1077
EBA1028
CBA1243
51
52
53
54
55
Arm
Arm
Arm
Guide
Guide
CNV5247
CNV5248
CNV5249
CNV5254
CNV5255
11
12
13
14
15
Screw(M2x4)
Washer
Washer
Washer
•••••
CBA1362
CBF1037
CBF1038
CBF1060
56
57
58
59
60
Gear
Gear
Guide
Damper
Arm
CNV5257
CNV5256
CNV6176
CNV6010
CNV6096
16
17
18
19
20
Spring
Spring
Spring
Spring
Spring
CBH2079
CBH2117
CBH2314
CBH2110
CBH2282
61
62
63
64
65
Arm
Arm
Guide
Guide
•••••
CNV6031
CNV6211
CNV6012
CNV5510
21
22
23
24
25
Spring
•••••
Spring
Spring
Spring
CBH2318
CBH2324
CBH2118
CBH2161
66
67
68
69
70
Guide
Clamper
Gear
Motor Unit(M1)
Screw Unit
CNV5751
CNV6013
CNV5813
CXB2190
CXB4726
26
27
28
29
30
Spring
Spring
Spring
Spring
Spring
CBH2163
CBH2189
CBH2249
CBH2260
CBH2262
71
72
73
74
75
Chassis Unit
Gear Unit
Arm Unit
Motor Unit(M2)
Lever Unit
CXB4797
CXB4728
CXB5753
CXB2195
CXB4730
31
32
33
34
35
Bracket
Spring
Connector
Connector
Shaft
CNC8568
CBL1369
CDE5531
CDE5532
CLA3304
76
77
78
79
80
Arm Unit
Motor Unit(M3)
Arm Unit
Bracket Unit
Screw
CXB4731
CXB2562
CXB4732
CXB4795
JFZ20P025FMC
36
37
38
39
40
Screw(M2.6x6)
Frame
Frame
Lever
Arm
CBA1458
CNC8565
CNC8749
CNC7546
CNC8663
81
82
83
84
85
Screw
Washer
Pickup Unit(Service)(P8)
Screw
PCB
JGZ17P025FZK
YE20FUC
CXX1285
IMS26P030FMC
CNX2982
41
42
43
44
45
Bracket
•••••
Spacer
Sheet
•••••
CNC8567
86
87
88
89
Photo-transistor(Q1, 2)
Damper
Lack
Spring
CPT230SX-TU
CNV6011
CNV6014
CBH2315
1
2
3
4
5
CNM3315
CNM6659
*
9
2
1
3
4
DEH-3130R,3100R-B,3100R
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
A
TUNER AMP UNIT
Q524
B
A
ANTENNA
FM/AM 1ST IF 10.7MHz
T51 Q51 CF51
CF52 CF53
FM FRONT END
Q3
CN502
1
Q525
Q540
Q542
FM/AM TUNER UNIT
24
32
2
39
42
44
46
63
RF TV
22
Q701
6
RDS
DECODER
46
VDD
24
fm/AM
70
MIXER.IF AMP DET
IC 1
PML002A
54
COMP
78
LDET
20
21
11
71
33 32 45
55 57
28
CF202
61 74
IC 701
PM4009A
18
65
35
Q201 Q204
19
IC 2 PM4008A
34 33 41 44 11 12 13
69
ANT2 TV
ANT1 TV
38
TMUTE
FM MPX
25
27
75
12
X501
EEPROM
5
AM RF
6
AM 2ND IF 450kHz
Q202
IC 3
BR9010FV
4
3
NL2
FMSD
SL
SDBL
CE1
CK
NL1
3
4
NL1
2
SD
13
SL
8
SDBW
PCE2
PDIO
12 15 16
CK
22 10 14
Q401
PCE1
VCC
25
CE2
DI/DO
VDD
PDIO
LOCL
VDD
SYS+B
B
PICKUP UNIT(SERVICE)(P8) D CONTROL UNIT
LD
MD
LD+
MD
Q101
CN101
CN701
98
14
97
TO+
B+D/E
4
3
23
M
12
11
C
CN801
LOADING
MOTOR
SOP
PD
SP601
ALARM
BUZZER
IC 201
UPD63711GC
2
3
RF-AMP, DSP,
SERVO, DAC
SD/MD
39
HOME
4
S801
HOME
SOM
14
COP
13 COM
10
LOP
9
LOM
1
M
CN681
LOUT
TD/FD
CD DRIVER
FOP
18 TOP
M
17
X201
TOP
16
CARRIAGE
MOTOR
8
FOP
IC 301
BA5985FM
SPINDLE
MOTOR
16
A+C/F
24
FO+
L_OUT
5
HOLOGRAM
UNIT
FOCUS ACT
TRACKING ACT
LD
FWD
REV
MUTE
1
CDLOAD
28
CDEJET
21
CONT
6
19
5
20
11
14
22
3
23
2
CDLOAD
CDEJET
CONT
4
CN802
EJTSNS
3
DSCSNS
1
CLAMP
VD
SELECT
SENSE
EJTSNS
DSCSNS
CLAMP
21
Q991
D803 D802 D801
2
VD
S802
CLAMP
DISC SENSE
E PHOTO
24
1
7
18
B.U
+5V REGULATOR
UNIT(S8)
VDD
4
IC 701
BA05SFP
1
IN
2
Q992
CD5VON
VDCONT
D
10
1
2
3
4
5
7
6
8
DEH-3130R,3100R-B,3100R
A
36
tmute
88
ldet
CN431
REAR L CH
29
Q431
FM/AM
SYSTEM
CONTROLLER
76
38
74
77
99
97
32
98
94
30
SD
SL
SDBW
TUNPCE
TUNPCK
TUNPCE2
TUNPDO
VST
VCK
VDT
TUNPDI
LOCL
Q434
Q973
VDD
B.U
B.U
BACKUP
FUSE
10A
2
B
BACK UP
1
2
3
GND
POWER AMP
IN1_L
FL–
23
ELECTRONIC VOLUME/
SOURCE SELECTOR
FL
IN2_L
IC 451
PML003AM
RL
10
14
IC 551
PAL005A
FL
12 RL
11
MUTE
STBY
B.REM
22
4
25
21
FL+
3
RL–
5
RL+
B.REM
9
FL–
11
FL+
10
RL–
12
RL+
5
B.REM
SYSPW
PDIO
IC 601(1/2)
PE5139A
NL1
Q551 MUTE
Q971
100
asens
PEE
ACC
4
ACC
bsens
ASENS
BSENS
DRSYS
TELMUTE
SYSPW
59
CDLOAD
58
CDEJET
53
CONT
92
Q921
TELMUTE
93
79
64
TELMUTE
TEL MUTE
7
1
2
C
3
SYSTEM
CONTROLLER
BACK
UP
IC 601(2/2)
PE5139A
78
B.U
B.
REM
SYSPW
MUTE
EJTSNS
28
DSCSNS
Q921
C
Q982
SYS+B
GND ACC
KEYBOARD UNIT
RR
FR
FL
RL
-
RR
+
FR
+
FL
+
RL
+
B.U
CLAMP
CN1801
CN651
DSENS
52
8
1
3
6
4
5
6
3
SWVDD
DSENS
78
23
AVCC VDD
56
KYDT
VDCONT
DPDT
95
96
RESET
RESET
11
1
RESET
IC 631
S–80735ANDZI
2
GRN
B.U
GRNILM
CD5VON
20
9
KYDT
LCD
DPDT
VDD
Q652
54
8
KEY CONTROLLER
AND
LCD DRIVER
IC 1801
PD6294A
GRN
Q653
D
KEY MATRIX
11
13
X1901
11
5
6
7
8
2
1
3
4
DEH-3130R,3100R-B,3100R
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)
Note: When ordering service parts, be sure to refer to “EXPLODED VIEWS AND PARTS LIST” or “ELECTRICAL
PARTS LIST”.
A-a
A
A-a
A-a
A-a
Large size
SCH diagram
A-b
A-b
A
TUNER AMP UNIT
Guide page
A-b
Detailed page
FM : -16.5dBs
AM : -27dBs
S-CD : 0dBs
FM(100%) : -15.5dBs
AM(30%) : -26dBs
SOURCE SELECTOR/
ELECTRONIC VOLUME
1
5
6
3
FM/AM TUNER UNIT
2
B
B
4
ANTENNA
CABLE
DSP-201M-S00B
SYSTEM CONTROLLER
C
VD REGULATOR
RDS DECODER
D E
Decimal points for resistor
and capacitor fixed values
are expressed as :
2.2 ←2R2
0.022 ← R022
D
12
A
1
2
3
CD MECHANISM
MODULE
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
S-CD : 4.4dBs
4
5
7
6
8
DEH-3130R,3100R-B,3100R
A-b
A
MUTE
REAR
PREOUT
FM : 5.84dBs
AM : -2.66dBs
S-CD : 9.74dBs
B
RESET
FM : 6.6dBs
AM : -1.9dBs
S-CD : 10.5dBs
POWER AMP
FM : 32dBs
AM : 24dBs
S-CD : 36dBs
>CEK1136
C
ERA15-02VH
ERA15-02VH
ERA15-02VH
VDD REGULATOR
1K(1/2W)
1
5
BACK UP SENSE
6
4
ACC SENSE
2
3
8V REGULATOR
4
3
1
ERA15-02VH
ERA15-02VH
2
5
6
1K(1/2W)
D
TELEPHONE MUTE
BACK
UP
ILLUMINATION
POWER SUPPLY
B.
REM
GND ACC
C
KEYBOARD UNIT
5
6
7
RR
FR
FL
RL
-
RR
+
FR
+
FL
+
RL
+
A
8
13
A
14
A-a
1
FM(100%) : -15.5dBs
AM(30%) : -26dBs
TUNER AMP UNIT
D
FM/AM TUNER UNIT
2
3
4
2
5
SYSTEM CONTROLLER
SOURCE SELECTOR/
ELECTRONIC VOLUME
A
6
1
B
FM : -16.5dBs
AM : -27dBs
S-CD : 0dBs
3
7
6
2
5
4
3
2
1
1
B
A-a A-b
DEH-3130R,3100R-B,3100R
3
4
C
4
ANTENNA
CABLE
DSP-201M-S00B
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
5
6
Decimal points for resistor
and capacitor fixed values
are expressed as :
2.2 ←2R2
0.022 ← R022
RDS DECODER
S-CD : 4.4dBs
VD REGULATOR
SYSTEM CONTROLLER
7
7
A-a
8
A-a A-b
12
11
6
KEYBOARD
UNIT
C
8
10
9
5
DEH-3130R,3100R-B,3100R
8
A
B
C
D
15
CD MECHANISM MODULE
D E
16
A-b
1
2
3
6
RESET
B
FM : 6.6dBs
AM : -1.9dBs
S-CD : 10.5dBs
POWER AMP
A
FM : 32dBs
AM : 24dBs
S-CD : 36dBs
FM : 5.84dBs
AM : -2.66dBs
S-CD : 9.74dBs
REAR
PREOUT
2
5
4
MUTE
1
7
3
2
1
A-a A-b
DEH-3130R,3100R-B,3100R
3
4
C
D
4
5
6
9
ILLUMINATION
POWER SUPPLY
TELEPHONE MUTE
4
ACC SENSE
BACK UP SENSE
3
1
4
6
8V REGULATOR
2
6
5
5
1
2
3
ERA15-02VH
ERA15-02VH
ERA15-02VH
B.
REM
7
A-b
8
RR
+
FR
+
FL
+
RL
+
A-a A-b
RR
FR
FL
RL
-
7
GND ACC
BACK
UP
1K(1/2W)
1K(1/2W)
>CEK1136
6
12
11
10
8
VDD REGULATOR
ERA15-02VH
5
DEH-3130R,3100R-B,3100R
8
A
B
C
D
17
ERA15-02VH
2
1
3
4
DEH-3130R,3100R-B,3100R
3.3 FM/AM TUNER UNIT
A
A
B
FM/AM TUNER UNIT
Mark
None
F0
F65
F125
A0
A74
A125
Band
–
FM
FM
FM
AM
AM
AM
Input Level
–
0dBf
65dBf
125dBf
0dBµ
74dBµ
125dBµ
KV1410(23)
KV1410(23)
B
DAN217U
DAN217U
C
D
18
B
1
2
3
4
5
6
7
8
DEH-3130R,3100R-B,3100R
KV1410(23)
A
B
C
D
5
6
7
B
8
19
2
1
3
4
DEH-3130R,3100R-B,3100R
3.4 KEYBOARD UNIT
C
KEYBOARD UNIT
A
CN651
A
B
5
3
1
6
4
2
5
3
1
6
4
2
5
3
1
6
4
2
5
3
1
6
4
2
5
3
1
6
4
2
5
3
1
6
4
2
5
3
1
6
4
2
5
3
1
6
4
2
5
3
1
6
4
2
6
5
4
3
2
1
6
5
4
3
2
1
6
5
4
3
2
1
5
3
1
6
4
2
5
3
1
6
4
2
6
5
4
3
2
1
5
3
1
6
4
2
5
3
1
6
4
2
5
3
1
6
4
2
C
D
20
C
1
2
3
4
5
7
6
8
DEH-3130R,3100R-B,3100R
A
: DEH-3130R/X1N/EW, 3100R/X1N/EW
: DEH-3100R-B/X1N/EW
B
C
5
D1809,1810
D1811
D1812,1813
S1801-1806,1808-1812,1816-1818
S1807,1813,1814,1819
DEH-3130R/X1N/EW
CL220D
CL170DCD
CL170DCD
CSG1114
CSG1117
DEH-3100R-B/X1N/EW
CL220SRCTS
CL170SRCD
CL170SRCD
CSG1135
CSG1133
DEH-3100R/X1N/EW
CL220PGC
CL170PGCD
CL170PGCD
CSG1112
CSG1107
R1806,1808
390
270
390
6
7
D
C
8
21
2
1
3
4
DEH-3130R,3100R-B,3100R
3.5 CD MECHANISM MODULE
D
A
CONTROL UNIT
PICKUP UNIT
(SERVICE)(P8)
CN101
B
RF-AMP, SE
C
E
PHOTO UNIT(S8)
Q1 CPT230SX-TU
CN802
Q2 CPT230SX-TU
SPINDLE MOTOR
M3 CXB2562
CARRIAGE MOTOR
M1 CXB2190
D
LOADING MOTOR
CD DRIVER
M2 CXB2195
CN801
22
D E
1
BA05SFP
2
5V REGULATOR
3
4
5
6
7
8
DEH-3130R,3100R-B,3100R
A
SWITCHES:
CONTROL UNIT
S801 : HOME SWITCH.....ON-OFF
S802 : CLAMP SWITCH....ON-OFF
The underlined indicates the switch position.
B
MP, SERVO, DSP, DAC, LPF
CN701
A
CN681
C
D
5
6
7
D
8
23
DEH-3130R,3100R-B,3100R
Note:1. The encircled numbers denote measuring pointes in the circuit diagram.
2. Reference voltage
REFO:2.5V
- Waveforms
1 RFI
0.5V/div. 0.5µs/div.
Normal mode: play
1 CH1: RFI
1V/div. 0.5ms/div.
2 CH2: MIRR
5V/div.
Test mode: Tracking open
1 CH1: RFI
1V/div.
0.5ms/div.
2 CH2: MIRR 5V/div.
Normal mode: The defect part
passes 800µm
REFO →
REFO
→
REFO →
REFO →
REFO →
3 CH1: FD
0.5V/div.
0.2s/div.
4 CH2: FO+
2V/div.
Test mode: No disc, Focus close
3 CH1: FD
0.5V/div.
0.2s/div.
5 CH2: FOK
2V/div.
Normal mode: Focus close
REFO →
6 CH1: FE
0.5V/div.
1ms/div.
7 CH2: XSI
2V/div.
Normal mode: Focus close
REFO →
REFO →
REFO →
REFO →
REFO →
8 CH1: TE
0.5V/div. 0.5ms/div.
9 CH2: TD
0.5V/div.
Test mode: 32 tracks jump (FWD)
8 CH1: TE
0.5V/div. 0.5ms/div.
9 CH2: TD
0.5V/div.
Test mode: Single jump (FWD)
GND →
8 CH1: TE
0.5V/div.
5ms/div.
9 CH2: TD
0.5V/div.
Test mode: 100 tracks jump (FWD)
REFO →
REFO →
REFO →
REFO →
REFO →
REFO →
6 CH1: FE
0.1V/div.
3 CH2: FD
0.2V/div.
Normal mode: Play
20ms/div.
3 CH1: FD
0.5V/div. 0.5s/div.
0 CH2: MD
1V/div.
Normal mode: Focus close (12cm)
3 CH1: FD
0.5V/div. 0.5s/div.
0 CH2: MD
1V/div.
Normal mode: Focus close (8cm)
REFO →
REFO →
REFO →
REFO →
REFO →
REFO →
24
DEH-3130R,3100R-B,3100R
8 CH1: TE
0.2V/div.
9 CH2: TD
0.2V/div.
Normal mode: play
20ms/div.
8 CH1: TE
0.5V/div.
5ms/div.
! CH2: SD
0.5V/div.
TEST mode: 100 Tracks jump(FWD)
0 MD
0.5V/div.
0.1s/div.
Normal mode: Play (12cm)
REFO →
REFO →
REFO →
REFO →
REFO →
0 MD
1V/div.
Normal mode:
Long Search (12cm)
10ms/div.
@ EFM
1V/div.
5µs/div.
Normal mode: play
8 CH1: TE
1V/div.
2ms/div.
# CH2: TEC
1V/div.
Test mode: Focus close
Tracking open
REFO →
REFO →
REFO →
REFO →
GND →
8 CH1: TE
0.5V/div.
0.2s/div.
6 CH2: FE
0.5V/div.
Normal mode: AGC after focus close
$ PLCK
2V/div.
0.5µs/div.
Normal mode: play
% SCKO
2V/div.
1µs/div.
Normal mode: play
REFO →
REFO →
^ Dout
2V/div.
Normal mode: play
10µs/div.
REFO →
REFO →
GND →
GND →
& LRCK
2V/div.
Normal mode: play
20µs/div.
* VD
5V/div.
50ms/div.
Normal mode: No disc
GND →
REFO →
REFO →
GND →
GND →
25
DEH-3130R,3100R-B,3100R
( CH1: R OUT 1V/div.
0.2ms/div.
) CH2: L OUT 1V/div.
Normal mode: Play (1kHz 0dB)
6 CH1: FE
0.2V/div.
1ms/div.
3 CH2: FD
0.5V/div.
Normal mode: During AGC
8 CH1: TE
0.2V/div.
1ms/div.
9 CH2: TD 0.5V/div.
Normal mode: During AGC
REFO →
REFO →
REFO →
REFO →
REFO →
REFO →
1 CH1: RFI
1V/div.
0.5ms/div.
⁄ CH2: HOLD 5V/div.
Normal mode: The defect part passes
800µm(B.D)
3 CH1: FD
0.5V/div.
0.5ms/div.
⁄ CH2: HOLD 5V/div.
Normal mode: The defect part passes
800µm(B.D)
9 CH1: TD
0.1V/div.
0.5ms/div.
⁄ CH2: HOLD 5V/div.
Normal mode: The defect part passes
800µm(B.D)
REFO →
REFO →
REFO →
REFO →
REFO →
REFO →
26
DEH-3130R,3100R-B,3100R
27
2
1
3
4
DEH-3130R,3100R-B,3100R
4. PCB CONNECTION DIAGRAM
4.1 TUNER AMP UNIT
NOTE FOR PCB DIAGRAMS
1. The parts mounted on this PCB
include all necessary parts for
several destination.
For further information for
respective destinations, be sure
to check with the schematic diagram.
2. Viewpoint of PCB diagrams
Connector
A TUNER AMP UNIT
CORD ASSY
A
Capacitor
SIDE A
B
P.C.Board
Chip Part
SIDE B
D
CN701
C
D
C
28
A
1
2
3
4
CN1801
5
7
6
8
DEH-3130R,3100R-B,3100R
A
SIDE A
IP BUS IN
SUB WOOFER/
REAR PREOUT
L ch
R ch
ANTENNA CABLE
B
B
C
D
5
6
7
A
8
29
1
2
3
4
3
4
DEH-3130R,3100R-B,3100R
A
TUNER AMP UNIT
A
B
C
D
30
A
1
2
5
6
7
8
DEH-3130R,3100R-B,3100R
SIDE B
A
B
C
D
5
6
7
A
8
31
2
1
3
4
DEH-3130R,3100R-B,3100R
4.2 FM/AM TUNER UNIT
SIDE A
A
A
B
FM/AM TUNER UNIT
C
B
D
32
1
2
3
4
1
2
3
4
DEH-3130R,3100R-B,3100R
SIDE B
A
B
FM/AM TUNER UNIT
C
B
D
33
1
2
3
4
D
34
C
1
2
SOURCE
1
2
3
4
5
6
B
TA,TI,
PROG
PTY,
DISP
CLOCK
AUDIO
←
2
VOL
DOWN
←
BAND
EJECT
FUNC
A
P.EQ–
P.EQ+
KEYBOARD UNIT
1
VOL
UP
C
DEH-3130R,3100R-B,3100R
3
3
4
4.3 KEYBOARD UNIT
SIDE A
←
C
4
←
1
2
3
4
DEH-3130R,3100R-B,3100R
SIDE B
A
B
KEYBOARD UNIT
A
CN651
C
C
D
1
2
3
C
4
35
36
PHOTO UNIT(S8)
CONTROL UNIT
1
D E
3
2
1
2
3
3
CN802
4.5 CD MECHANISM MODULE
E
2
D
CN681
A
M3 SPINDLE MOTOR
M1 CARRIAGE MOTOR
M2 LOADING MOTOR
1
A
HOME
PICKUP UNIT(SERVICE)(P8)
C
E
D
DEH-3130R,3100R-B,3100R
4
SIDE A
B
D
4
1
2
3
4
DEH-3130R,3100R-B,3100R
SIDE B
A
CLAMP
CONTROL UNIT
B
D
C
D
1
2
3
D
4
37
DEH-3130R,3100R-B,3100R
5. ELECTRICAL PARTS LIST
NOTES:
- Parts whose parts numbers are omitted are subject to being not supplied.
- The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
A
Part No.
-------------------------
Unit Number : CWM6841
Unit Name
: Tuner Amp Unit
MISCELLANEOUS
IC
IC
IC
IC
IC
451
551
601
631
701
IC
IC
IC
IC
IC
PML003AM
PAL005A
PE5139A
S-80734AN
PM4009A
Q
Q
Q
Q
Q
431
434
502
507
524
Transistor
Transistor
Transistor
Transistor
Transistor
IMH3A
DTA124EU
2SC4081
DTA124EU
IMH3A
Q
Q
Q
Q
Q
525
540
541
542
551
Transistor
Transistor
Transistor
Transistor
Transistor
DTA114ES
2SC1740S
2SD1757K
2SD1757K
DTC144ES
Q
Q
Q
Q
Q
601
651
652
653
701
Transistor
Transistor
Transistor
Transistor
Transistor
DTA114ES
2SA933S
2SB1236
DTC124ES
DTA124ES
Q
Q
Q
Q
Q
921
971
973
981
982
Transistor
Transistor
Transistor
Transistor
Transistor
2SA1576
IMX1
2SD1859
2SD2396
IMD2A
Q
Q
D
D
D
991
992
651
654
655
Transistor
Transistor
Diode
Diode Network
Diode Network
2SD2396
IMD2A
MTZ5R6J(C)
DA204U
DA204U
D
D
D
D
D
656
921
931
932
951
Diode Network
Diode
Diode
Diode
Diode
DA204U
DAN202U
ERA15-02VH
ERA15-02VH
ERA15-02VH
D
D
D
D
D
952
971
972
973
974
Diode
Diode
Diode
Diode
Diode
ERA15-02VH
HZS7L(C2)
HZS6L(C3)
ERA15-02VH
HZS6L(B1)
D
D
L
L
L
981
992
501
504
506
Diode
Diode
Ferri-Inductor
Ferri-Inductor
Inductor
HZS9L(B3)
HZS9L(B1)
LAU4R7K
LAU2R2K
LAU100K
L
L
L
L
L
601
619
621
651
701
Inductor
Ferri-Inductor
Ferri-Inductor
Ferri-Inductor
Ferri-Inductor
LAU100K
LAU2R2K
LAU2R2K
LAU101K
LAU101K
38
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
L
L
L
TH
X
702
921
951
601
601
Inductor
Ferri-Inductor
Choke Coil 600µH
Thermistor
Radiator 12.58291MHz
LAU100K
LAU2R2K
CTH1221
CCX1031
CSS1402
X
701
BZ
AR
601
501
Crystal Resonator 3.648MHz
FM/AM Tuner Unit
Buzzer
CSS1447
CWE1500
CPV1050
DSP-201M-S00B
RESISTORS
R
R
R
R
R
421
431
432
437
438
RS1/10S473J
RS1/10S821J
RS1/10S821J
RS1/10S223J
RS1/10S223J
R
R
R
R
R
443
445
465
466
502
RS1/10S0R0J
RS1/8S473J
RD1/4PU221J
RD1/4PU221J
RD1/4PU222J
R
R
R
R
R
503
508
509
510
511
RS1/10S222J
RS1/10S681J
RS1/10S473J
RS1/10S681J
RS1/10S473J
R
R
R
R
R
512
513
514
515
516
RS1/10S681J
RS1/8S473J
RS1/10S681J
RS1/8S473J
RS1/10S681J
R
R
R
R
R
517
518
519
520
521
RS1/8S472J
RS1/10S103J
RS1/10S393J
RS1/10S681J
RS1/10S473J
R
R
R
R
R
522
523
526
527
528
RD1/4PU681J
RS1/10S473J
RS1/10S104J
RS1/10S104J
RD1/4PU102J
R
R
R
R
R
530
531
532
533
534
RS1/10S681J
RS1/10S473J
RD1/4PU681J
RS1/10S473J
RS1/10S162J
R
R
R
R
R
535
536
537
540
541
RS1/10S162J
RS1/10S272J
RS1/10S272J
RS1/10S224J
RS1/10S224J
DEH-3130R,3100R-B,3100R
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
R
R
R
R
R
542
543
544
545
546
RS1/10S224J
RS1/10S222J
RS1/10S222J
RS1/10S223J
RS1/10S223J
R
R
R
R
R
982
987
991
992
993
RD1/4PU511J
RD1/4PU221J
RD1/4PU221J
RD1/4PU221J
RS1/10S472J
R
R
R
R
R
547
570
579
580
602
RS1/10S472J
RD1/4PU103J
RS1/10S331J
RS1/10S103J
RD1/4PU473J
R
994
RS1/10S222J
R
R
R
R
R
603
606
607
608
610
RS1/10S102J
RD1/4PU102J
RD1/4PU102J
RD1/4PU102J
RS1/10S222J
R
R
R
R
R
611
613
614
615
616
RS1/10S473J
RS1/10S0R0J
RD1/4PU222J
RD1/4PU473J
RS1/10S222J
R
R
R
R
R
617
618
625
626
631
RS1/10S473J
RN1/10SE2002D
RS1/10S0R0J
RD1/4PU102J
RS1/10S102J
R
R
R
R
R
632
641
651
652
653
RS1/10S822J
RD1/4PU102J
RS1/10S222J
RD1/4PU472J
RS1/10S222J
R
R
R
R
R
654
655
656
657
658
RD1/4PU222J
RD1/4PU222J
RD1/4PU222J
RS1/10S473J
RD1/4PU472J
R
R
R
R
R
659
660
662
681
682
RS1/8S472J
RD1/4PU302J
RS2PMF200J
RS1/10S681J
RD1/4PU102J
R
R
R
R
R
683
684
704
705
706
RS1/10S102J
RD1/4PU102J
RS1/10S102J
RD1/4PU102J
RD1/4PU102J
R
R
R
R
R
713
714
716
717
718
RS1/10S0R0J
RD1/4PU102J
RS1/10S0R0J
RS1/10S225J
RS1/10S0R0J
R
R
R
R
R
727
921
923
924
925
RD1/4PU681J
RS1/10S153J
RS1/10S472J
RD1/4PU102J
RS1/10S473J
R
R
R
R
R
971
972
973
974
975
RS1/10S103J
RS1/10S473J
RS1/10S103J
RS1/10S473J
RS1/10S473J
R
R
R
R
R
976
977
978
979
981
RS1/10S473J
RD1/4PU101J
RS1/10S472J
RS1/10S472J
RS1/10S1R0J
CAPACITORS
C
C
C
C
C
431
432
451
452
453
CEJA4R7M35
CEAL4R7M35
CKSYB224K25
CKSYB224K25
CKSYB474K16
C
C
C
C
C
454
455
456
457
458
CKSYB474K16
CEJANP4R7M16
CEJANP4R7M16
CKSQYB153K50
CKSQYB153K50
C
C
C
C
C
461
462
463
465
466
CEAL470M10
CKSQYB104K25
CEJA100M16
CCSQSL182J50
CCSSL182J50
C
C
C
C
C
501
502
503
504
505
CKSQYB103K50
CKSQYB223K50
CKSQYB223K50
CEJA220M10
CKSQYB102K50
C
C
C
C
C
506
507
508
509
519
CEAL101M10
CKSQYB473K25
CCSQCH101J50
CKSQYB102K50
CKSQYB472K50
C
C
C
C
C
524
525
531
536
537
CEJA1R0M50
CEJA1R0M50
CKSQYB182K50
CKSQYB123K50
CKSQYB123K50
C
C
C
C
C
540
551
552
553
554
CKSQYB223K50
CKSYB224K25
CKSYB224K25
CKSYB224K25
CKSYB224K25
C
C
C
C
C
556
570
571
572
573
C
C
C
C
C
601
602
603
604
605
CCSQCH200J50
CCSQCH200J50
CKSYB105K16
CEJA4R7M35
CCSQCH101J50
C
C
C
C
C
607
609
619
621
622
CCSQCH101J50
CCSQCH101J50
CCSQCH101J50
CCSQCH101J50
CCSQCH101J50
C
C
C
C
C
631
652
653
701
702
CEJA2R2M50
CEJA4R7M35
CKSQYB473K25
CEAL220M6R3
CKSQYB104K25
4700µF/16V
CCH1328
CEJA100M16
CEJA330M10
CKSYB105K16
CKSYB104K50
39
DEH-3130R,3100R-B,3100R
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
C
C
C
C
C
711
712
715
717
718
CCSQCH270J50
CCSQCH270J50
CKSQYB104K50
CKSQYB471K50
CKSYB471K50
R
R
R
R
R
9
10
11
12
13
RS1/16S223J
RS1/16S473J
RS1/16S221J
RS1/16S103J
RS1/16S104J
C
C
C
C
C
721
722
971
972
973
CEAL220M6R3
CKSQYB104K25
CCH1331
CKSQYB473K25
CEJA101M10
R
R
R
R
R
16
17
18
19
20
RS1/16S223J
RS1/16S221J
RS1/16S221J
RS1/16S473J
RS1/16S470J
C
C
C
C
C
974
981
982
983
991
CKSQYB473K25
CCH1326
CKSQYB103K50
CEJA101M16
CKSQYB473K25
R
R
R
R
R
51
52
53
54
55
RS1/16S470J
RS1/16S103J
RS1/16S103J
RS1/16S331J
RS1/16S331J
C
C
992
993
CKSQYB102K50
CEJA101M10
R
R
R
R
R
56
57
58
59
60
RS1/16S560J
RS1/16S560J
RS1/16S102J
RS1/16S225J
RS1/16S133J
R
R
R
R
R
61
62
101
102
103
RS1/16S433J
RS1/16S562J
RS1/16S333J
RS1/16S103J
RS1/16S333J
R
R
R
R
R
104
106
108
110
111
RS1/16S562J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S154J
RS1/16S273J
R
R
R
R
R
112
113
114
115
116
RS1/16S223J
RS1/16S222J
RS1/16S333J
RS1/16S334J
RS1/16S473J
R
R
R
R
R
117
118
122
202
203
RS1/16S333J
RS1/16S223J
RS1/16S0R0J
RS1/16S472J
RS1/16S225J
R
R
R
R
R
204
205
206
208
209
RS1/16S102J
RS1/16S220J
RS1/16S471J
RS1/16S104J
RS1/16S104J
R
R
R
R
R
210
213
251
902
904
RS1/16S563J
RS1/16S223J
RS1/16S225J
RS1/16S103J
RS1/16S473J
R
R
R
R
907
908
909
914
RS1/16S103J
RS1/16S681J
RS1/16S473J
RS1/16S562J
B
470µF/16V
330µF/16V
Unit Number : CWE1500
Unit Name
: FM/AM Tuner Unit
MISCELLANEOUS
IC
IC
IC
Q
Q
1
2
3
1
2
IC
IC
IC
Transistor
Transistor
PML002A
PM4008A
BR9010FV
2SC4081
DTC124EU
Q
Q
Q
Q
Q
3
51
201
202
204
FET
Transistor
FET
Transistor
Transistor
3SK263
2SC4081
2SK932
DTC124EU
2SC4081
D
D
D
D
D
1
2
4
6
101
Diode
Diode
Diode
Diode
Diode
KV1410(23)
1SV248
KV1410(23)
KV1410(23)
1SS355
D
D
D
D
L
201
202
903
904
1
Diode
Diode
Diode
Diode
Coil
DAN217U
DAN217U
KV1410(23)
SVC253
CTC1155
L
L
L
L
L
2
3
4
201
202
Coil
Inductor
Coil
Inductor
Inductor
CTC1155
LCTB100K2125
CTC1155
LCTB330K1608
CTF1287
L
L
L
L
L
203
901
902
904
905
Inductor
Coil
Inductor
Inductor
Inductor
LCTA121J3225
CTC1154
LCTA3R3J3225
LCTBR47K1608
LCTBR47K1608
T
CF
CF
CF
CF
51
51
52
53
202
Coil
Ceramic Filter
Ceramic Filter
Ceramic Filter
Ceramic Filter
CTE1132
CTF1442
CTF1442
CTF1442
CTF1348
X
901
Crystal Resonator 10.250MHz
CSS1432
RESISTORS
R
R
R
R
R
40
1
2
6
7
8
RS1/16S153J
RS1/16S103J
RS1/16S103J
RS1/16S273J
RS1/16S473J
CAPACITORS
C
C
C
C
C
1
2
4
6
8
CCSQCH5R0C50
CCSRCH5R0C50
CCSRCJ3R0C50
CKSQYB105K10
CKSRYB222K50
C
C
C
C
C
10
11
12
14
15
CCSRCH220J50
CCSRCH150J50
CCSRCH8R0D50
CCSRCJ3R0C50
CKSRYB103K50
DEH-3130R,3100R-B,3100R
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
C
C
C
C
C
16
17
18
19
20
CKSRYB222K50
CKSRYB222K50
CCSRCJ3R0C50
CKSRYB103K50
CKSRYB103K50
C
C
C
C
C
226
902
904
905
906
CKSRYB682K25
CCSRCH270J50
CKSRYB223K25
CKSRYB103K50
CCSRTH100D50
C
C
C
C
C
21
24
31
32
35
CKSRYB103K50
CKSQYB334K16
CKSRYB222K50
CCSRCH470J50
CKSRYB103K50
C
C
C
C
C
907
909
910
912
913
CCSRTH150J50
CCSRTH100D50
CKSRYB332K50
CKSQYB474K16
CKSRYB223K25
C
C
C
C
C
51
52
53
54
55
CKSRYB103K50
CKSRYB473K16
CCSRCK2R0C50
CKSRYB103K50
CKSRYB104K16
C
C
C
C
C
914
915
916
917
918
CKSRYB682K25
CKSQYB223K25
CKSQYB474K16
CKSYB475K10
CKSRYB223K25
C
C
C
C
C
56
58
59
60
101
CKSRYB104K16
CKSQYB224K16
CKSRYB223K25
CKSRYB104K16
CEALNP100M10
C
C
C
C
C
919
920
921
922
923
CKSQYB225K10
CCSRCH270J50
CCSRCH270J50
CKSYB105K16
CKSRYB103K50
C
C
C
C
C
102
103
105
106
107
CCSRCH151J50
CKSRYB473K16
CKSRYB682K25
CEAL2R2M50
CKSRYB103K50
C
C
C
C
C
C
108
109
110
111
112
CKSQYB474K16
CKSQYB474K16
CKSRYB104K16
CKSRYB104K16
CKSRYB104K16
C
C
C
C
C
113
114
115
116
117
CKSRYB123K25
CEAL220M6R3
CKSRYB473K16
CEAL2R2M50
CKSRYB102K50
C
C
C
C
C
120
121
122
123
125
CKSRYB153K25
CKSRYB332K50
CKSRYB682K25
CKSRYB681K50
CKSRYB103K50
C
C
C
C
C
126
127
128
201
202
CKSRYB103K50
CEAL2R2M50
CKSRYB103K50
CCSRCH471J50
CCSRCH100D50
C
C
C
C
C
203
204
205
206
207
CKSRYB104K16
CKSRYB332K50
CKSRYB103K50
CKSRYB104K16
CKSRYB473K16
C
C
C
C
C
208
209
210
211
212
CCSRCH560J50
CEAL470M6R3
CKSRYB103K50
CKSRYB103K50
CCSRCH101J50
C
C
C
C
C
215
216
217
219
220
CKSRYB223K25
CKSQYB334K16
CKSRYB103K50
CKSQYB105K10
CKSRYB104K16
C
C
C
C
C
221
222
223
224
225
CKSRYB473K16
CKSQYB334K16
CKSQYB474K16
CKSRYB104K16
CKSRYB272K50
Unit Number : CWM6796
Unit Name
: Keyboard Unit
: (DEH-3130R/X1N/EW)
MISCELLANEOUS
IC
D
D
D
D
1801
1801
1802
1803
1804
IC
Diode Network
Diode Network
LED
LED
PD6294A
DA204U
DA204U
NSSW440-9159
NSSW440-9159
D
D
D
D
D
1807
1808
1809
1810
1811
LED
LED
LED
LED
LED
NSSW440-9159
NSSW440-9159
CL220D
CL220D
CL170DCD
D
D
X
S
S
1812
1813
1801
1801
1802
LED
LED
Radiator 5.00MHz
CL170DCD
CL170DCD
CSS1423
CSG1114
CSG1114
S
S
S
S
S
1803
1804
1805
1806
1807
CSG1114
CSG1114
CSG1114
CSG1114
CSG1117
S
S
S
S
S
1808
1809
1810
1811
1812
CSG1114
CSG1114
CSG1114
CSG1114
CSG1114
S
S
S
S
S
1813
1814
1815
1816
1817
CSG1117
CSG1117
CSG1111
CSG1114
CSG1114
S
S
S
S
S
1818
1819
1820
1821
1822
CSG1114
CSG1117
CSG1111
CSG1111
CSG1111
LCD
CAW1570
RESISTORS
R
R
R
R
R
1801
1802
1803
1806
1808
RS1/8S222J
RS1/8S222J
RS1/10S472J
RS1/4S391J
RS1/4S391J
41
DEH-3130R,3100R-B,3100R
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
R
R
R
R
R
1809
1810
1811
1812
1813
RS1/4S301J
RS1/4S301J
RS1/4S301J
RS1/4S301J
RS1/4S301J
RESISTORS
R
R
R
R
R
1814
1815
1816
1817
1818
RS1/4S301J
RS1/4S431J
RS1/4S431J
RS1/4S821J
RS1/10S103J
R
R
1819
1821
RS1/10S0R0J
RS1/4S272J
CAPACITORS
C
C
C
C
C
1801
1803
1804
1805
1806
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
C
C
C
C
1807
1808
1811
1812
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
C
Unit Number : CWM6797
Unit Name
: Keyboard Unit
: (DEH-3100R-B/X1N/EW)
MISCELLANEOUS
IC
D
D
D
D
1801
1801
1802
1803
1804
IC
Diode Network
Diode Network
LED
LED
PD6294A
DA204U
DA204U
NSSW440-9159
NSSW440-9159
D
D
D
D
D
1807
1808
1809
1810
1811
LED
LED
LED
LED
LED
NSSW440-9159
NSSW440-9159
CL220SRCTS
CL220SRCTS
CL170SRCD
D
D
X
S
S
1812
1813
1801
1801
1802
LED
LED
Radiator 5.00MHz
CL170SRCD
CL170SRCD
CSS1423
CSG1135
CSG1135
S
S
S
S
S
1803
1804
1805
1806
1807
CSG1135
CSG1135
CSG1135
CSG1135
CSG1133
S
S
S
S
S
1808
1809
1810
1811
1812
CSG1135
CSG1135
CSG1135
CSG1135
CSG1135
S
S
S
S
S
1813
1814
1815
1816
1817
CSG1133
CSG1133
CSG1111
CSG1135
CSG1135
S
S
S
S
S
1818
1819
1820
1821
1822
CSG1135
CSG1133
CSG1111
CSG1111
CSG1111
LCD
42
CAW1572
Part No.
-------------------------
R
R
R
R
R
1801
1802
1803
1806
1808
RS1/8S222J
RS1/8S222J
RS1/10S472J
RS1/4S271J
RS1/4S271J
R
R
R
R
R
1809
1810
1811
1812
1813
RS1/4S301J
RS1/4S301J
RS1/4S301J
RS1/4S301J
RS1/4S301J
R
R
R
R
R
1814
1815
1816
1817
1818
RS1/4S301J
RS1/4S431J
RS1/4S431J
RS1/4S821J
RS1/10S103J
R
R
1819
1821
RS1/10S0R0J
RS1/4S272J
CAPACITORS
C
C
C
C
C
1801
1803
1804
1805
1806
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
C
C
C
C
1807
1808
1811
1812
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
C
Unit Number : CWM6795
Unit Name
: Keyboard Unit
: (DEH-3100R/X1N/EW)
MISCELLANEOUS
IC
D
D
D
D
1801
1801
1802
1803
1804
IC
Diode Network
Diode Network
LED
LED
PD6294A
DA204U
DA204U
NSSW440-9159
NSSW440-9159
D
D
D
D
D
1807
1808
1809
1810
1811
LED
LED
LED
LED
LED
NSSW440-9159
NSSW440-9159
CL220PGC
CL220PGC
CL170PGCD
D
D
X
S
S
1812
1813
1801
1801
1802
LED
LED
Radiator 5.00MHz
CL170PGCD
CL170PGCD
CSS1423
CSG1112
CSG1112
S
S
S
S
S
1803
1804
1805
1806
1807
S
S
S
S
S
1808
1809
1810
1811
1812
S
S
S
S
S
1813
1814
1815
1816
1817
Switch
CSG1112
CSG1112
CSG1112
CSG1112
CSG1107
CSG1112
CSG1112
CSG1112
CSG1112
CSG1112
Switch
Switch
CSG1107
CSG1107
CSG1111
CSG1112
CSG1112
DEH-3130R,3100R-B,3100R
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
=====Circuit Symbol and No.===Part Name
--- -----------------------------------------------
Part No.
-------------------------
S
S
S
S
S
CSG1112
CSG1107
CSG1111
CSG1111
CSG1111
R
R
R
R
R
602
605
606
801
803
RS1/16S102J
RS1/16S0R0J
RS1/16S0R0J
RS1/8S751J
RS1/8S751J
CAW1570
R
R
902
906
RS1/16S0R0J
RS1/16S0R0J
1818
1819
1820
1821
1822
Switch
LCD
RESISTORS
CAPACITORS
R
R
R
R
R
1801
1802
1803
1806
1808
RS1/8S222J
RS1/8S222J
RS1/10S472J
RS1/4S391J
RS1/4S391J
R
R
R
R
R
1809
1810
1811
1812
1813
RS1/4S301J
RS1/4S301J
RS1/4S301J
RS1/4S301J
RS1/4S301J
R
R
R
R
R
1814
1815
1816
1817
1818
RS1/4S301J
RS1/4S431J
RS1/4S431J
RS1/4S821J
RS1/10S103J
R
R
1819
1821
RS1/10S0R0J
RS1/4S272J
CAPACITORS
C
C
C
C
C
1801
1803
1804
1805
1806
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
C
C
C
C
1807
1808
1811
1812
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
CKSQYB104K50
D
Unit Number : CWX2411
Unit Name
: Control Unit
MISCELLANEOUS
IC
IC
IC
Q
D
201
301
701
101
801
IC
IC
IC
Transistor
LED
UPD63711GC
BA5985FM
BA05SFP
2SB1132
CL200IRX
D
X
S
S
802
201
801
802
LED
Ceramic Oscillator 16.934MHz
Spring Switch(HOME)
Spring Switch(CLAMP)
CL200IRX
CSS1456
CSN1051
CSN1052
RESISTORS
R
R
R
R
R
101
102
103
201
202
RS1/8S120J
RS1/8S100J
RS1/16S222J
RS1/16S104J
RS1/16S103J
R
R
R
R
R
203
204
205
206
207
RS1/16S393J
RS1/16S103J
RS1/16S103J
RS1/16S182J
RS1/16S123J
R
R
R
R
R
302
303
501
502
601
RS1/16S153J
RS1/16S103J
RS1/16S102J
RA4C681J
RS1/16S102J
C
C
C
C
C
101
102
103
104
105
CCSRCH102J25
CKSRYB104K16
CEV101M6R3
CEV470M6R3
CKSQYB334K16
C
C
C
C
C
106
107
201
202
203
CKSQYB334K16
CKSQYB334K16
CKSRYB104K16
CKSRYB471K50
CKSRYB104K16
C
C
C
C
C
205
206
207
208
209
CEV101M6R3
CKSRYB104K16
CKSRYB104K16
CKSRYB104K16
CKSRYB104K16
C
C
C
C
C
210
211
212
213
214
CKSRYB332K50
CKSRYB104K16
CKSRYB104K16
CKSRYB392K50
CKSRYB104K16
C
C
C
C
C
215
216
217
218
219
CKSRYB104K16
CCSRCJ3R0C50
CCSRCH270J50
CKSRYB104K16
CCSRCH181J50
C
C
C
C
C
220
221
222
223
224
CCSRCH510J50
CKSRYB682K25
CEV220M6R3
CKSRYB103K25
CKSRYB224K10
C
C
C
C
C
301
603
604
702
703
CEV101M10
CCSQSL152J50
CCSQSL152J50
CCH1349
CKSQYB334K16
E
Q
Q
10µF/10V
Unit Number :
Unit Name
: Photo Unit(S8)
1
2
Photo-transistor
Photo-transistor
CPT230SX-TU
CPT230SX-TU
Miscellaneous Parts List
M
M
M
1
2
3
Pickup Unit(Service)(P8)
Motor Unit(CARRIAGE)
Motor Unit(LOADING)
Motor Unit(SPINDLE)
Fuse(10A)
CXX1285
CXB2190
CXB2195
CXB2562
CEK1136
43
DEH-3130R,3100R-B,3100R
6. ADJUSTMENT
6.1 CD ADJUSTMENT
1) Precautions
• This unit uses a single power supply (+5V) for the regulator. The signal reference potential, therefore, is
connected to REFO(approx. 2.5V) instead of GND.
If REFO and GND are connected to each other by mistake during adjustments, not only will it be impossible to measure the potential correctly, but the servo
will malfunction and a severe shock will be applied to
the pick-up. To avoid this, take special note of the following.
Do not connect the negative probe of the measuring
equipment to REFO and GND together. It is especially
important not to connect the channel 1 negative
probe of the oscilloscope to REFO with the channel 2
negative probe connected to GND.
Since the frame of the measuring instrument is usually at the same potential as the negative probe, change
the frame of the measuring instrument to floating status.
If by accident REFO comes in contact with GND,
immediately switch the regulator or power OFF.
• Always make sure the regulator is OFF when connecting and disconnecting the various filters and wiring
required for measurements.
• Before proceeding to further adjustments and measurements after switching regulator ON, let the player
run for about one minute to allow the circuits to stabilize.
• Since the protective systems in the unit's software are
rendered inoperative in test mode, be very careful to
avoid mechanical and /or electrical shocks to the system when making adjustment.
• Disc detection during loading and eject operations is
performed by means of a photo transistor in this
unit.Consequently, if the inside of the unit is exposed
to a strong light source when the outer casing is
removed for repairs or adjustment, the following malfunctions may occur.
*During PLAY, even if the eject button is
pressed,the disc will not be ejected and the unit
will remain in the PLAY mode.
*The unit will not load a disc.
When the unit malfunctions this way, either re-position the light source, move the unit or cover the photo
transistor.
44
2) Test Mode
This mode is used for adjusting the CD mechanism
module of the device.
• Test mode starting procedure
Reset while pressing the 4 and 6 keys together.
• Test mode cancellation
Switch ACC, back-up OFF.
• After pressing the EJECT key, do not press any other
key until the disk is completely ejected.
• If the ] or [ key is pressed while focus search is in
progress, immediately turn the power off (otherwise
the actuator may be damaged due to adhesion of the
lenses).
• Jump operation of TRs other than 100TR continues
after releasing the key. CRG move and 100TR jump
operations are brought into the “Tracking close” status when the key is released.
• Powering Off/On resets the jump mode to “Single TR
(91)”, the RF AMP gain setting to 0 dB, and the automatic adjustment value to the initial value.
DEH-3130R,3100R-B,3100R
- Flow Chart
4
6
Test Mode In
Reset
SOURCE
Select CD
New test mode
BAND
TRK
MIN
Power ON
(Not adjustment for T.Offset)
SEC
00 00 00
Display
2
3
6
*1
Power ON
(Adjustment for T.Offset)
TRK
Display
MIN
SEC
RF AMP Gain Select
TRK
99 99 99
MIN
SEC
GG GG GG
Power OFF
BAND
3
Focus Close/
S Curve Check
TRK
MIN
SEC
TRK
Display
<Tracking Servo Close>
MIN
[
*8
*2
Focus Mode
Select
91 91 91
Display
]
1
6
TRK
SEC
0x 0x 0x
MIN
SEC
TRK
MIN
MIN
SEC
TRK
MIN
TRK
99 99 99
MIN
SEC
00 00 00
or
SEC
*3
Auto Adjustment
Display Select
CRG-
00 00 00
or
TRK
*8
CRG+
00 00 00
2
or
SEC
TRK
99 99 99
MIN
SEC
99 99 99
Power OFF
6
1
BAND
T.Close and
F,T AGC and
RF AGC and
Fit Servo
]
3
T. Close and
Fit Servo
RF AGC Coefficient Display/
Rough Servo and RF AGC
[
CRG+
TRK
Display
MIN
2
T.Balance
Adjustment
CRGTRK
SEC
MIN
8x 8x 8x
8x 8x 8x
or
or
TRK
MIN
SEC
TRK
SEC
MIN
SEC
9x 9x 9x
9x 9x 9x
Tracking
Open
Power OFF
*7
*5
F, T, RF AGC/
F.Bias Display Select
F, T AGC and
RF AGC
[
]
6
3
1
BAND
CRG/TR Jump NO.
Select
2
*4 CRG-/TR Jump- *4
CRG+/TR Jump+
*6
TRK
Power OFF
Display
TRK
2
+6dB
06 06 06
+12dB
12 12 12
TRK
Display
*2
Display
*3
Focus Close
00 00 00
(99 99 99)
F.Offset Display
SEC
SEC
8x 8x 8x
or
S Curve Check
01 01 01
RF.Offset Display
MIN
MIN
9x 9x 9x
Tracking
Open
TYP
Display
SEC
or
BAND
*1
MIN
8x 8x 8x
TRK
MIN
SEC
9x 9x 9x
F.Cansel Display
F.Cancel Value = {Top Rank 8bit of Set Value (7F [H] to 80 [H] ) + 128} / 4
= 63 [D] to (32 [D] ) to 00 [D]
*4 Single TR/32TR/100TR
*5
Single TR
Display 9x(8x):91(81)
32TRK
92(82)
100TRK
93(83)
CRG Move
94(84)
*6 CRG Move, 100TR Jump Only
*7
TRK, MIN, SEC
F.AGC Gain
T.AGC Gain
RF AGC Gain
(F,T.AGC Gain = (Present Value/Initial Value) × 20)
*8 Voltage of CRG Motor = 2 [V]
45
DEH-3130R,3100R-B,3100R
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT
• Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted
PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if
the PU unit must be changed, the grating should be checked using the procedure below.
• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
• Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
• Method :
• Measuring Equipment
• Measuring Points
• Disc
• Mode
• Oscilloscope, Two L.P.F.
• E, F, REFOUT
• ABEX TCD-784
• TEST MODE
CONTROL UNIT
E
F
L.P.F.
E
Xch
100kΩ
390pF
REFO
F
REFO
Ych
Oscilloscope
100kΩ
390pF
REFO
L.P.F.
• Checking Procedure
1. In test mode, load the disc and switch the 5V regulator on.
2. Using the ] and [ buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
46
DEH-3130R,3100R-B,3100R
Grating waveform
Ech → Xch 20mV/div, AC
Fch → Ych 20mV/div, AC
0°
30°
45°
60°
75°
90°
47
DEH-3130R,3100R-B,3100R
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 TEST MODE
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the
error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the
users and also for facilitating trouble analysis and repair work in servicing.
(1) Basic Indication Method
1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains
in blank as before.
2) Head unit display examples
Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.
8-digit display
ERROR–xx
6-digit display
ERR–xx
OR
Err–xx
4-digit display
E–xx
(2) Error Code List
Code Class
Displayed error code Description of the code and potential cause(s)
10
Electricity Carriage Home NG
CRG can't be moved to inner diameter.
CRG can't be moved from inner diameter.
→ Failure on home switch or CRG move mechanism.
11
Electricity
Focus Servo NG
Focusing not available.
→ Stains on rear side of disc or excessive vibrations on REWRITABLE.
12
Electricity
Spindle Lock NG
Spindle not locked. Sub-code is strange (not readable).
→ Failure on spindle, stains or damages on disc, or excessive vibrations.
Subcode NG
A disc not containing CD-R data is found. Turned over disc are found,
though rarely.
→ Failure on home switch or CRG move mechanism.
RF AMP NG
An appropriate RF AMP gain can't be determined.
→ CD signal error.
17
Electricity
Setup NG
APC protection doesn't work. Focus can be easily lost.
→ Damages or stains on disc, or excessive vibrations.
30
Electricity
Search Time Out
Failed to reach target address.
→ CRG tracking error or damages on disc.
A0
System
Power Supply NG
Power (VD) is ground faulted.
→ Failure on SW transistor or power supply (failure on connector).
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).
Unreadable TOC does not constitute an error. An intended operation continues in this case.
A newly designed head unit must conform to the example given above.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, 3x: Search relevant errors, Ax: Other errors.
48
DEH-3130R,3100R-B,3100R
- New Test Mode
S-CD plays the same way as before.
If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its
cause and time occurred (in absolute time) are displayed.
During setup, operational status of the control software (internal RAM: CPOINT) is displayed.
These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis.
(1) Shifting to the New Test Mode
1 Turn on the current test mode by starting the reset from the key.
2 Select S-CD for the source through the specified procedure including use of the [SOURCE] key, and inserting the
disc. Then, press the [Jump Mode Selector] key while maintaining the regulator turned off.
3 After the above operations, the new test mode remains on irrespective of whether the S-CD is turned on or off.
You can reset the new test mode by turning on the reset start.
* With some products, the new test mode can be reset through the same operations as that employed for shifting to
the STBY mode (while maintaining the Acc turned off).
(2) Key Correspondence
Key
Test mode
(Example)
Power Off
Power On
BAND To power on
To power off
(offset adjustment performed)
In-play
–
New test mode
Error Production
Time/Err.No. switching
]
–
FWD-Kick
FF/TR+
–
[
–
REV-Kick
REV/TR-
–
1
–
Scan
–
2
RF AMP gain switching
T.Close (AGC performed)
/parameter display switching
Parameter display switching
/T.BAL adjustment/T.Open
F.Close/RF AGC/F.T.AGC
Mode
–
3
To power on
–
–
(offset adjustment not performed)
6
–
F.Mode switching
Auto/Manu T.No./Time switching
/T.Close (no AGC)/Jump switching
Note: Eject and CD on/off is performed in the same procedure as that for the normal mode.
(3) Cause of Error and Error Code
Code Class
Contents
40
Electricity Off focus detected.
Description and cause
FOK goes low.
→ Damages/stains on disc, vibrations or failure on servo.
41
Electricity
Spindle unlocked.
FOK = Low continued for 50 msec.
→ Damages/stains on disc, vibrations or failure on servo.
42
Electricity
Sub-code unreadable.
Sub-code was unreadable for 50 msec.
→ Damages/stains on disc, vibrations or failure on servo.
43
Electricity
Sound skipping detected.
Last address memory function was activated.
→ Damages/stains on disc, vibrations or failure on servo.
Note: Mechanical errors during aging are not displayed.
The error codes should be indicated in the same way as in the normal mode.
49
DEH-3130R,3100R-B,3100R
(4) Display of Operational Status (CPOINT) during Setup
Status No. Contents
00
CD+5V ON process in progress.
01
Servo LSI initialization (1/3) in progress.
02
Servo LSI CRAM initialization in progress.
03
Servo LSI initialization (2/3) in progress.
04
Offset adjustment (1/3) in progress.
05
Offset adjustment (2/3) in progress.
06
Offset adjustment (3/3) in progress.
07
FZD adjustment in progress.
08
Servo LSI initialization (3/3) in progress.
10
Carriage move to home position started.
11
Carriage move to home position started.
12
Carriage is moving toward inner diameter.
13
Carriage is moving toward outer diameter.
14
15
20
21
22
23
24
25
Carriage outer kick in progress.
Carriage outer diameter feed (1 second) in progress.
Servo close started.
Pre-processing for focus search started.
Spindle rotation and focus search started.
Waiting for focus close (XSI=Low).
Standing by after focus close is over.
Focus search preprocessing is in
progress while setup protection is turned on.
Focus search preprocessing is in
progress while focus recovery is turned on.
Wait time after focus close is set up.
Standing by after focus close is over.
Setup (1/2) before T balance adjustment is started.
Setup (2/2) before T balance adjustment is started.
T balance adjustment started.
T balance adjustment (1/2).
T balance adjustment (2/2).
Waiting for spindle rotation to end.
Spindle rough servo.
Standing by after spindle rough servo is over.
RF AGC started.
RF AGC started.
RF AGC ending process in progress.
Tracking close in progress.
Standing by after tracking is closed.
Carriage closing in progress.
Focus/tracking AGC started.
Focus AGC started.
Focus AGC in progress.
Tracking AGC in progress.
Standing by after focus/tracking AGC are over.
Spindle processes applicable servo.
Check for servo close is started.
Check of LOCK pin started.
RF AGC started.
RF AGC in progress.
Standing by after RF AGC is over.
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
50
Protective action
None
None
None
None
None
None
None
None
None
None
None
Specified 10 seconds has been passed or failure
on home switch.
Specified 10 seconds has been passed or failure
on home switch.
None
None
None
None
None
Specified focus search time has been passed.
Specified focus search time has been passed.
None
None
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus.
Off focus or spindle not locked.
Off focus.
Off focus.
Off focus.
DEH-3130R,3100R-B,3100R
(5) Display Examples
1) During Setup (When status no. = 11)
TRK No.
MIN.
SEC.
11
11'
11"
2) During Operation (TOC read, TRK search, Play, FF and REV)
The same as in the normal mode.
3) When a Protection Error Occurred
Switch to the following displays (A) and (B) using the [BAND] switch:
(A) Error occurrence timing display in absolute time.
An example: Error occurred in 12th tune at 34'56" in absolute time.
TRK No.
12
MIN.
34'
SEC.
56"
(B) Error No. display
An example: Error #40 (Off focus is detected)
ERROR-40
51
DEH-3130R,3100R-B,3100R
7.1.2 DISASSEMBLY
- Removing the Case Unit(not shown)
1. Remove the Case Unit.
- Removing the Panel Assy(Fig.1)
Disengage the stoppers at two locations.
Remove the Panel Assy.
- Removing the CD Mechanism Module
(not shown)
1. Remove the four screws.
2.Disconnect the connector, and then remove the
CD Mechanism Module.
Panel Assy
Fig.1
- Removing the Tuner Amp Unit(Fig.2)
Remove the two screws.
Remove the three screws.
Remove the screw.
Straighten the tabs at four locations indicated.
Remove the Tuner Amp Unit.
Tuner Amp Unit
52
Fig.2
DEH-3130R,3100R-B,3100R
- Removing the Upper Frame
1. Remove six Springs A, two Springs B and four
Screws.
2. Remove two Tabs situated on rear side of the Upper
Frame, remove two Arms on the front side, then
remove two Tabs on the front side.
A
Upper Frame
A
A
A
B
A
Arm
Arm
B
A
- Removing the Carriage Mechanism
Carriage Mechanism Section
1. Disengage the Carriage Mechanism from the two
dampers situated in the front side by driving it up,
then disengage and remove the mechanism from the
one damper by driving it up aslant into front side
direction.
Note : When assembling the Carriage Mechanism, coat
the dampers with alcohol prior to the assembly.
- Removing the Clamp Arm Assy
A
Clamp Arm Assy Section
1. Remove a Spring A, a B and a Spring C.
2. Drive the Clamp Arm Assy up into rear side direction,
then disengage the arm from its current position
Finally, drive the assembly approximately 45 degrees
upward, then slide the assembly toward right side to
remove it.
B
C
53
DEH-3130R,3100R-B,3100R
- Removing the Guide Arm Assy
1. Remove a connector, a spring A and B
2. Drive the Guide Arm Assy up aslant into rear side
direction, then remove it from a Pin. Finally, drive the
assembly approximately 45 degrees upward, then
slide the assembly toward left side to remove it.
Note : When assembling the guide arm assembly, route
the cord inside the assembly. In this operation,
care must be exercised so that cord may be
caught by the gear.
Guide Arm Assy Section
A
B
Pin
LO Arm Assy Section
- Removing the LO Arm Assy
1. Remove two Pins to dismount the LO Arm Assy.
- Removing the Control Unit and the Spindle
Short Pin
Motor
1. Remove from the connector after mounting the short
pin on the flexible PCB of the pickup unit.
2. Remove two Soldered joints, then remove two
Screws A.
3. Remove two connectors and a Screw B.
4. Disengage the Control Unit from two Tabs, then dismount the unit by sliding it toward left.
5. Dismount the Spindle Motor.
Spindle Motor
B
Control Unit
A
54
A
DEH-3130R,3100R-B,3100R
- Removing the Loading Motor and Carriage
C
Motor
Guide
1. Remove the Spring and two Screws A.
2. Dismount the Loading Motor.
3. Remove the Belt, a Screw B, two Screws C, a Guide
and a Screw Unit.
4. Dismount the Carriage Motor.
Note : When assembling the Belt, use care so that it
may not be contaminated by grease.
B
Screw Unit
Carriage Motor
Belt
C
A
A
Loading Motor
- Removing the Pickup Unit
1. Remove two Screws and a Shaft.
2. Dismount the Pickup Unit.
Pickup Unit
Shaft
55
DEH-3130R,3100R-B,3100R
7.1 PARTS
7.2.1 IC
- Pin Functions (PE5139A)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23,24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42,43
44
45
46
47–50
51
52
53
54
55
56
57
58
59
60
56
Pin Name
DRSYS
TELMUTE
SYSPW
DRELAY
TESTIN
drst
ERROR
sk
RECIVE
TUNPW
reset
XT2
XT1
VSS
X2
X1
REGOFF
REGC
VDD
GRNILM
NC
adpw
NC
ASENBO
ROMDATA
ROMCLK
MUTE
fm/AM
LOCL
LOCH
TUNPCE2
VCK
VST
VDT
tmute
ROMCS
SD
st
VSS
VDD
NC
rdslk
currq
RDT
NC
swvdd
dsens
CONT
CD5VON
NC
VDCONT
CDMUTE
CDEJET
CDLOAD
LOCK
I/O
O
I
O
O
I
O
O
I
O
O
I
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
I
I
I
O
I
O
I
O
O
O
O
O
O
I
Function and Operation
Door system select output
Telephone mute input
System power supply control output
External relay output
Test program mode input
RDS reset output
RDS disapprove of error correction output
RDS SK signal input
During RDS data reception output
Tuner power control output
Reset input
Not used (open)
Not used (GND)
GND
Crystal oscillator connection pin
Crystal oscillator connection pin
Connect to VSS
Capacitor for regulator connect pin
Power supply
Green illumination select output
Not used
A/D converter power supply output
Not used
Slave power supply control output
ROM correction data output
ROM correction clock output
System mute output
RDS decoder power select output
LOCL output
LOCH output
PLL IC chip enable output
Clock output for electronic volume
Strobe pulse output for electronic volume
Data output for electronic volume
Tuner mute output
ROM correction chip select output
SD input
FM stereo input
GND
Power supply
Not used
RDS LK signal input
Tuner voltage FIX output
RDS demodulation data input
Not used
Keyboard unit power supply control output
Grille detach sense input
CD server driver power control output
CD +5V power control output
Not used
CD VD power control output
CD mute control output
CD eject control output
CD LOAD motor loading control output
CD spindle lock input
DEH-3130R,3100R-B,3100R
Pin No.
61
62
63
64
65
66
67
68
69
70
71,72
73
74
75
76
77
78
79
80
81
82
83
84
85,86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Pin Name
FOK
PCL
MIRR
clamp
xsck
XSI
XSO
XA0
xrst
xstb
NC
TEST
SL
MODEL1
NL1
SDBW
EJTSNS
DSCSNS
VDSENS
TEMP
(VDD)
(VDD)
(GND)
NC
GND
ldet
rck
RDS57K
SRVCNT
asens
bsens
TUNPDI
KEYDT
DPDT
TUNPCK
TUNPDO
TUNPCE
PEE
I/O
I
O
I
I
O
I
O
O
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
O
O
O
O
O
Function and Operation
CD focus OK input
Clock adjustment output
CD mirror detector input
CD disc clamp sense input
CD LSI clock output
CD LSI data input
CD LSI data output
CD LSI command/data control output
CD LSI reset output
CD LSI strobe output
Not used
Test terminal
Tuner signal level input
Model select input
RDS noise level input
SD bandwidth input
CD disc EJECT position detect
CD disc detect input
CD VD over voltage / short-circuit sense input
CD temperature sense input (CD)
A/D converter power supply terminal
A/D converter reference voltage terminal
A/D converter GND
Not used
GND
RDS PLL lock sense input
RDS demodulation clock input
RDS 57kHz pulse count input
Not used
ACC power sense input
Back up power sense input
PLL IC data input
Key data input
Display data output
PLL IC clock output
PLL IC data output
PLL IC chip enable
Beep tone output
1
30
*PE5139A
50
81
80
100
51
31
IC's marked by* are MOS type.
Be careful in handling them because they are very
liable to be damaged by electrostatic induction.
57
DEH-3130R,3100R-B,3100R
- Pin Functions (PD6294A)
Pin No.
1
2
3
4
5,6
7
8
9
10
11,12
13-16
17-22
23
24-73
74-77
78
79,80
Pin Name
VSS
X1
X0
NC
MOD1,0
NC
KYDT
DPDT
REMIN
NC
kd$-kd!
KST6-KST1
VDD
SEG49-0
COM3-0
VLCD
V2,V1
I/O
Function and Operation
GND
Crystal oscillator connection pin
Crystal oscillator connection pin
Not used
Connect to GND
Not used
Key data output
Display data input
Remote control pulse input
Not used
Key data input
Key strobe output
VDD
LCD segment output
LCD common output
LCD voltage input
Power supply terminal
I
O
I
I
I
O
O
O
I
BR9010FV
1
20
*PD6294A
21
NC
80
1
VCC
40
8
WC
GND
CS
2 CS : Chip select input
7
SK : Serial data clock input
DI : Serial data input
DO : Serial data output
3 WC: Write control input
6
SK
4
DI
DO
60
41
61
5
PAL005A
Protector
Mute
Amp2
Mute
Mute
Amp3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
OUT2-
STBY
OUT2+
VCC
OUT1-
P-GND1
OUT1+
SVR
IN1
IN2
S-GND
IN4
IN3
Ac_gnd
OUT3+
P-GND3
OUT3-
VCC
OUT4+
MUTE
OUT4-
P-GND4
Switch_out
Amp4
P-GND2
Amp1
TAB
STBY
58
Mute
DEH-3130R,3100R-B,3100R
PML003AM
VCC
IN1_R
IN2_R
28
27
26
IN3_R IN4+_R IN4-_R
23
25
24
LoudAGND out_R
22
SVin_R
Frontout_R
20
19
21
Rearout_R FIE_R
18
17
STB
DATA
16
15
Isolator
circuit
FIE
Anti Alias
filter
Auto-Zero
Primary
volume
Anti radiation
filter
Fader
volume
Treble
Loudness
volume
Middle
Bass
Secondary
volume
Zero cross
detect circuit
Digital block
Auto-Zero
Primary
volume
Anti Alias
filter
Middle
Bass
Zero cross
detect circuit
Treble Loudness
volume
Fader
volume
Anti radiation
filter
Secondary
volume
FIE
Isolator
circuit
1
2
3
4
Vref
IN1_L
IN2_L
IN3_L
5
6
IN4+_L IN4-_L
7
8
AGND Loudout_L
9
10
SVin_L Frontout_L
11
12
Rear- FIE_L
out_L
13
14
DGND
CLK
PM4009A
59
DEH-3130R,3100R-B,3100R
- Pin Functions (UPD63711GC)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
60
Pin Name
D.GND
RFOK
rst
A0
stb
sck
SO
SI
xtalen
D.VDD
DA.VDD
R_OUT
DA.GND
REGC
DA.GND
L_OUT
DA.VDD
R+
RLL+
X.VDD
XTAL
xtal
X.GND
D.VDD
EMPH
FLAG
I/O
O
I
I
I
I
O
I
I
O
I
O
O
O
O
O
I
O
O
O
29
30
31
32
33
34
DIN
DOUT
SCKIN
SCKO
LRCKIN
LRCK
I
O
I
O
I
O
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
HOLD
TX
D.GND
C16M
LIMIT
D.VDD
LOCK
RFCK
MIRR
PLCK
D.GND
C1D1
C1D2
C2D1
C2D2
C2D3
D.VDD
PACK
TSO
TSI
tsck
TSTB
D.GND
O
O
O
I
O
O
O
O
O
O
O
O
O
O
O
I
I
I
Function and Operation
Logic circuit GND
RFOK signal output
Reset signal input
Command/parameter identification signal input
Data strobe signal input
Clock signal input for serial data input/output
Serial data and status signal output
Serial data input
Crystal oscillation control pin
Positive power supply terminal to logic circuit
Positive power supply terminal to D/A converter
Right channel audio output signal
D/A converter GND
The outside putting capacitor connection pin for SCF regulator
D/A converter GND
Left channel audio output signal
Positive power supply terminal to D/A converter
Right channel audio data output
Right channel audio data output
Left channel audio data output
Left channel audio data output
Positive power supply terminal to crystal oscillation circuit
Crystal oscillator connect pin
Crystal oscillator connect pin
Crystal oscillation circuit GND
Positive power supply terminal to logic circuit
Output pin for the pre-emphasis data in the sub-Q code
Flag output pin to indicate that audio data currently being output consists
of noncorrectable data
Serial data input to internal DAC
Serial audio data output
Serial clock input to internal DAC
Audio data that is output from DOUT changes at rising edge of this clock
LRCK signal input to internal DAC
Signals to distinguish the right and left channels of the audio data output
from DOUT
Defect detection output
Digital audio interface data output
Logic circuit GND
Oscillator clock buffering output
Status of the pin is output at Bit 5 of the status output
Positive power supply terminal to logic circuit
EFM synchronous detection signal
Frame synchronous signal of XTAL-system
MIRR output
Monitor pin of bit clock
Logic circuit GND
Output pin for indicating the C1 error correction results
Output pin for indicating the C1 error correction results
Output pin for indicating the C2 error correction results
Output pin for indicating the C2 error correction results
Output pin for indicating the C2 error correction results
Positive power supply terminal to logic circuit
CD-TEXT PACK synchronous signal
CD-TEXT data serial output
CD-TEXT control parameter serial input
CD-TEXT serial clock input
CD-TEXT parameter strobe signal input
Logic circuit GND
DEH-3130R,3100R-B,3100R
Pin Name
TEST0
TEST1
ATEST
A.GND
FD
TD
SD
MD
DAC0
DAC1
DAC2
DAC3
A.VDD
EFM
ASY
C3T
RFI
AGCO
AGCI
RFO
EQ2
EQ1
RFA.GND
A
C
B
D
F
E
A.VDD
REFOUT
FEFEO
TETEO
TE2
TEC
A.GND
PD
LD
PN
A.VDD
I/O
I
I
O
Function and Operation
Test pin
Test pin
Test pin
Analog circuit GND
Focus drive output
Tracking drive output
Sled drive output
Spindle drive output
DAC output for adjustment
DAC output for adjustment
DAC output for adjustment
DAC output for adjustment
Positive power supply terminal to analog circuit
EFM signal output
EFM comparator reference voltage input
3T detection capacitor additional pin
RF signal input for EFM data regulation
RF signal output of after gain adjustment
RF-AGC amplifier input
RF summing amplifier output
RF amplifier equalizer parts additional pin
RF amplifier equalizer parts additional pin
RF summing amplifier inverted input
Analog circuit GND
Photo detector A input
Photo detector C input
Photo detector B input
Photo detector D input
Photo detector F input
Photo detector E input
Positive power supply terminal to analog circuit
Reference electric potential output
Focus error amplifier inverted input
Focus error amplifier output
Tracking error amplifier inverted input
Tracking error amplifier output
Tracking error output of after amplification
Tracking comparator input
Analog circuit GND
PD detection signal input for LD output monitor
LD control current output
APC circuit control polarity set pin
Positive power supply terminal to analog circuit
O
O
O
O
O
O
O
O
O
I
I
O
I
O
I
I
I
I
I
I
I
O
I
O
I
O
O
I
I
O
I
1
1
25
20
Pin No.
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
*UPD63711GC
50
40
76
61
75
60
100
80
51
41
26
21
61
DEH-3130R,3100R-B,3100R
- Pin Functions (BA5985FM)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
BA5985FM
62
Pin Name
FWD
OPIN1(+)
OPIN1(−)
OPOUT1
OPIN2(+)
OPIN2(−)
OPOUT2
VCC
VOL(−)
VOL(+)
VO2(−)
VO2(+)
VO1(−)
VO1(+)
VO4(+)
VO4(−)
VO3(+)
VO3(−)
GND
BIAS
MUTE
OPOUT3
OPIN3(−)
OPIN3(+)
OPOUT4
OPIN4(−)
OPIN4(+)
REV
I/O
I
I
I
O
I
I
O
O
O
O
O
O
O
O
O
O
O
I
O
I
I
O
I
I
I
Function and Operation
Loading driver FWD input
CH1 pre-amplifier input
CH1 pre-amplifier inverted input
CH1 pre-amplifier output
CH2 pre-amplifier input
CH2 pre-amplifier inverted input
CH2 pre-amplifier output
Power supply
Loading driver negative output
Loading driver positive output
Driver CH2 negative output
Driver CH2 positive output
Driver CH1 negative output
Driver CH1 positive output
Driver CH4 positive output
Driver CH4 negative output
Driver CH3 positive output
Driver CH3 negative output
GND
Bias input
Mute control
CH3 pre-amplifier output
CH3 pre-amplifier inverted input
CH3 pre-amplifier input
CH4 pre-amplifier output
CH4 pre-amplifier inverted input
CH4 pre-amplifier input
Loading driver REV input
DEH-3130R,3100R-B,3100R
7.2.2 DISPLAY
COMMON
SEGMENT
- CAW1570(DEH-3130R/X1N/EW, DEH-3100R/X1N/EW), CAW1572(DEH-3100R-B/X1N/EW)
63
DEH-3130R,3100R-B,3100R
8. OPERATIONS AND SPECIFICATIONS
8.1 OPERATIONS
5/∞/2/3 buttons
Disc loading slot
EJECT button
FUNCTION button
+/– button
AUDIO button
BAND button
DETACH button
EQ button
Buttons 1 – 6
DISPLAY button
PTY button
SOURCE button
64
TA/NEWS button
Hold for 1 second
3. Turn the source OFF.
2. Raise or lower the volume.
• The sound source will not change if no disc is set in this product.
• When this product’s blue/white lead is connected to the car’s Auto-antenna relay control terminal,
the car’s Auto-antenna extends when this product’s source is switched ON. To retract the antenna,
switch the source OFF.
Note:
Each press of the SOURCE button selects the desired source in the following order:
Built-in CD player = Tuner
Each press changes the Source ...
1. Select the desired source (e.g. Tuner).
• Loading a disc in this product.
Note:
The following explains the initial of operations required before you can listen to music.
To Listen to Music
Basic Operation
Seek Tuning
2 seconds or more
Broadcast station preset memory
• Up to 18 FM stations (6 in FM1, FM2 and FM3) and 6
MW/LW stations can be stored in memory.
• You can also use the 5 or ∞ buttons to recall broadcast
stations memorized in buttons 1 through 6.
Note:
2 seconds or less
Preset station recall
• You can memorize broadcast stations in buttons
1 through 6 for easy, one-touch station recall.
Preset Tuning
Band Indicator
Frequency Indicator
FM 1 = FM 2 = FM 3
= MW/LW
Band
Preset Number Indicator
• If you continue pressing the button for longer than 0.5 seconds, you can skip broadcast
stations. Seek Tuning starts as soon as you release the button.
• Stereo indicator “” lights when a stereo station is selected.
Note:
0.5 seconds or less
0.5 seconds or more
Manual Tuning (step by step)
• You can select the tuning method by changing the length of time you
press the 2/3 button.
Manual and Seek Tuning
This product’s AF function can be switched ON and OFF. AF should be switched OFF for
normal tuning operations.
Basic Operation of Tuner
DEH-3130R,3100R-B,3100R
65
66
• The CD function can be turned
ON/OFF with the disc remaining in
this product.
• A disc left partially inserted after
ejection may incur damage or fall out.
Note:
Eject
Play Time Indicator
Continue pressing
Fast Forward/Reverse
• If a disc cannot be inserted fully or playback fails, make sure the recorded side is down. Press the
EJECT button and check the disc for damage before reinserting it.
• If a CD is inserted with the recorded side up, it will be ejected automatically after a few moments.
• If the Built-in CD player cannot operate properly, an error message (such as “ERROR-14”) appears
on the display.
Note:
0.5 seconds or less
Track Search
• You can select between Track Search or Fast Forward/Reverse by pressing
the 2/3 button for a different length of time.
Track Search and Fast Forward/Reverse
Track Number Indicator
• The Built-in CD player plays one standard 12 cm or 8 cm (single) CD
at a time. Do not use an adapter when playing 8 cm CD.
Note:
Disc Loading Slot
Basic Operation of Built-in CD Player
Basic Operation
3. Cancel the Audio Menu.
2. Operate a mode.
Each press changes the Mode ...
1. Select the desired mode in the Audio Menu.
• After entering the Audio Menu, if you do not perform an operation within about 30 seconds, the
Audio Menu is automatically canceled.
Note:
With this Menu, you can adjust the sound quality.
Entering the Audio Menu
• You can create different “CUSTOM” curves for different sources.
Note:
POWERFUL +
= NATURAL +
= VOCAL +
= CUSTOM +
= EQ FLAT +
= SUPER BASS
Equalizer curve
• Move the EQ button up or down to select the desired Equalizer curve.
You can switch between Equalizer curves.
Selecting the Equalizer Curve
Audio Adjustment
DEH-3130R,3100R-B,3100R
• If you make adjustments when a curve other than “CUSTOM” is selected, the newly adjusted curve
will replace the previous adjusted curve. Then a new curve with “CUSTOM” appears on the display
while selecting the equalizer curve.
Note:
The display shows “+6” – “–6”.
3. Boost or attenuate the selected
band with the 5/∞ buttons.
EQ-LOW +
= EQ-MID +
= EQ-HIGH
2. Select the band you want to
adjust with the 2/3 buttons.
1. Press the AUDIO button and select the Equalizer mode
(EQ-LOW/MID/HIGH) in the Audio Menu.
You can adjust the currently selected equalizer curve settings as desired. Adjusted
equalizer curve settings are memorized in “CUSTOM”.
Equalizer Curve Adjustment (EQ-LOW/MID/HIGH)
• “FADER : 0” is the proper setting when 2 speakers are in use.
Note:
“BAL :L 9” – “BAL :R 9” is displayed as it moves from left to right.
3. Adjust left/right speaker balance with the 2/3 buttons.
“FADER :F 15” – “FADER :R 15” is
displayed as it moves from front to
rear.
2. Adjust front/rear speaker balance with the 5/∞ buttons.
1. Press the AUDIO button and select Fader/Balance mode (FADER) in the
Audio Menu.
This function allows you to select a Fader/Balance setting that provides ideal listening conditions in all occupied seats.
Balance Adjustment (FADER)
The Audio Menu features the following functions.
Audio Menu Functions
Audio Adjustment
“
”
“FIE”
• After switching the F.I.E. function ON, select the Fader/Balance mode in the Audio Menu, and
adjust front and rear speaker volume levels until they are balanced.
• Switch the F.I.E. function OFF when using a 2-speaker system.
Note:
100 +
= 160 +
= 250 (Hz)
3. Select the desired frequency
with the 2/3 buttons.
2. Switch the F.I.E. function
ON/OFF with the 5/∞ buttons.
1. Press the AUDIO button and select the F.I.E. mode (FIE) in the Audio Menu.
• When the F.I.E. function is deactivated, the rear speakers output sound of all frequencies, not just
bass sounds. Reduce the volume before disengaging F.I.E. to prevent a sudden increase in volume.
Precaution:
The F.I.E. (Front Image Enhancer) function is a simple method of enhancing front imaging
by cutting mid- and high-range frequency output from the rear speakers, limiting their output to low-range frequencies. You can select the frequency you want to cut.
Front Image Enhancer Function (FIE)
LOW +
= MID +
= HI
3. Select the desired level with the
2/3 buttons.
2. Switch the Loudness function
ON/OFF with the 5/∞ buttons.
1. Press the AUDIO button and select the Loudness mode (LOUD) in the Audio
Menu.
The Loudness function compensates for deficiencies in the low and high sound ranges at
low volume. You can select a desired Loudness level.
Loudness Adjustment (LOUD)
DEH-3130R,3100R-B,3100R
67
68
4*
5*
Connect leads of the same
color to each other.
Fuse resistor
Fuse resistor
Yellow/black
If you use a cellular telephone, connect it via the Audio Mute
lead on the cellular telephone. If not, keep the Audio Mute
lead free of any connections.
Black (ground)
To vehicle (metal) body.
Red (4*)
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.
Yellow (2*)
To terminal always supplied
with power regardless of
ignition switch position.
ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. If this is the case, be sure to
connect to both connectors.
Red (5*)
Accessory
(or back-up)
Yellow (3*)
Back-up
(or accessory)
Cap (1*)
When not using this terminal,
do not remove the cap.
2*
3*
1*
Note:
Depending on the kind of vehicle, the function
of 3* and 5* may be different. If this is the
case, be sure to connect 2* to 5* and 4* to 3*.
Fuse
Blue/white
To system control terminal of
the power amp. (Max. 300 mA
12 V DC.)
This Product
Speaker leads
White
: Front left +
White/black : Front left ≠
Gray
: Front right +
Gray/black : Front right ≠
Green
: Rear left +
Green/black : Rear left ≠
Violet
: Rear right +
Violet/black : Rear right ≠
Blue/white (6*)
Blue/white (7*)
To Auto-antenna relay control terminal.
(Max. 300 mA 12 V DC.)
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7*
when Pin 5 is an antenna control type. In another
type of vehicle, never connect 6* and 7*.
Refer to “Connecting to a Sold Separately Power Amp”.
Rear output
Refer to “Connecting to a Sold
Separately Power Amp”.
Antenna jack
DEH-3130R,3100R-B,3100R
DEH-3130R,3100R-B,3100R
8.2 SPECIFICATIONS
General
CD player
Power source .......... 14.4 V DC (10.8 – 15.1 V allowable)
Grounding system ........................................ Negative type
Max. current consumption ...................................... 10.0 A
Dimensions
(mounting size) ...... 178 (W) × 50 (H) × 159 (D) mm
(front face) .............. 188 (W) × 58 (H) × 19 (D) mm
Weight ...................................................................... 1.5 kg
System .................................... Compact disc audio system
Usable discs .................................................. Compact disc
Signal format .................... Sampling frequency: 44.1 kHz
Number of quantization bits: 16; linear
Frequency characteristics .............. 5 – 20,000 Hz (±1 dB)
Signal-to-noise ratio ...... 94 dB (1 kHz) (IEC-A network)
Dynamic range ............................................ 92 dB (1 kHz)
Number of channels ............................................ 2 (stereo)
Amplifier
Maximum power output ...................................... 45 W × 4
Continuous power output .................................... 27 W × 4
(DIN45324, +B = 14.4 V)
Load impedance .......................... 4 Ω (4 – 8 Ω allowable)
Preout maximum output
level/output impedance ............................ 2.2 V/1 kΩ
Equalizer (3-Band Parametric Equalizer)
(Low) .......................... Frequency: 40/80/100/160 Hz
Q Factor: 0.35/0.59/0.95/1.15
(+6 dB when boosted)
Level: ±12 dB
(Mid) .......................... Frequency: 200/500/1k/2k Hz
Q Factor: 0.35/0.59/0.95/1.15
(+6 dB when boosted)
Level: ±12 dB
(High) ................ Frequency: 3.15k/8k/10k/12.5k Hz
Q Factor: 0.35/0.59/0.95/1.15
(+6 dB when boosted)
Level: ±12 dB
Loudness contour
(Low) .................. +3.5 dB (100 Hz), +3 dB (10 kHz)
(Mid) ................ +10 dB (100 Hz), +6.5 dB (10 kHz)
(High) ................ +11 dB (100 Hz), +11 dB (10 kHz)
(volume: –30 dB)
FM tuner
Frequency range ...................................... 87.5 – 108 MHz
Usable sensitivity...................................................... 11 dBf
(1.0 µV/75 Ω, mono, S/N: 30 dB)
50 dB quieting sensitivity .... 16 dBf (1.7 µV/75 Ω, mono)
Signal-to-noise ratio ...................... 70 dB (IEC-A network)
Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo)
Frequency response ...................... 30 – 15,000 Hz (±3 dB)
Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)
MW tuner
Frequency range ...................................... 531 – 1,602 kHz
Usable sensitivity .............................. 18 µV (S/N: 20 dB)
Selectivity .................................................. 50 dB (±9 kHz)
LW tuner
Frequency range ........................................ 153 – 281 kHz
Usable sensitivity .............................. 30 µV (S/N: 20 dB)
Selectivity .................................................. 50 dB (±9 kHz)
Note:
• Specifications and the design are subject to possible modification without notice due to improvements.
69