Download OPERATOR`S MANUAL

GENERAL SAFETY RULES
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.

When servicing a power tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance instructions may create a risk of
shock or injury.
WARNING!
To reduce the risk of injury, user must read
instruction manual.
SPECIFIC SAFETY RULES
SAFETY WARNINGS COMMON FOR GRINDING, SANDING, WIRE BRUSHING AND POLISHING OPERATIONS
 Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
 This power tool is intended to function as a grinder,
stopping small abrasive or workpiece fragments. he
sander, wire brush, or polisher. Read all safety warneye protection must be capable of stopping flying
ings, instructions, illustrations and specifications
debris generated by various operations. The eye
provided with this power tool. Failure to follow all inprotection must be capable of stopping flying debris
structions listed below may result in electric shock, fire
generated by various operations. The dust mask or
and/or serious injury.
respirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high intensity
 Operations such as cutting-off are not recommended
noise may cause hearing loss.
to be performed with this power tool. Operations for
which the power tool was not designed may create a
 Keep bystanders a safe distance away from work area.
hazard and cause personal injury.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a
 Do not use accessories which are not specifically debroken accessory may fly away and cause injury beyond
signed and recommended by the tool manufacturer.
immediate area of operation.
Just because the accessory can be attached to your
power tool, does not assure safe operation.
Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting acThe rated speed of the accessory must be at least
cessory may contact hidden wiring or its own cord.
equal to the maximum speed marked on the power
Cutting accessory contacting a ²live² wire may make
tool. Accessories running faster than their RATED SPEED
exposed metal parts of the power tool ²live² and shock
can break and fly apart.
the operator.
 The outside diameter and the thickness of your acces Position the cord clear of the spinning accessory. If
sory must be within the capacity rating of your power
you lose control, the cord may be cut or snagged and your
tool. Incorrectly sized accessories cannot be adequately
hand or arm may be pulled into the spinning accessory.
guarded or controlled.
 Never lay the power tool down until the accessory
 The arbour size of wheels, flanges, backing pads or
has come to a complete stop. The spinning accessory
any other accessory must properly fit the spindle of
may grab the surface and pull the power tool out of your
the power tool. Accessories with arbour holes that do
control.
not match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause
 Do not run the power tool while carrying it at your
loss of control.
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into your
 Do not use a damaged accessory. Before each use inbody.
spect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess
 Regularly clean the power tool’s air vents. The motor’s
wear, wire brush for loose or cracked wires. If power
fan will draw the dust inside the housing and excessive
tool or accessory is dropped, inspect for damage or
accumulation of powdered metal may cause electrical
install an undamaged accessory. After inspecting and
hazards.
installing an accessory, position yourself and bystand Do not operate the power tool near flammable
ers away from the plane of the rotating accessory and
materials. Sparks could ignite these materials.
run the power tool at maximum no-load speed for one


Do not use accessories that require liquid coolants.
minute. Damaged accessories will normally break apart
Using water or other liquid coolants may result in
during this test time.
electrocution or shock.
4 - English