Download Samsung DVD-P345D User Manual

DVD Player
DVD-P345D
UK
AK68-00420A
Precautions
1. Setting up
* Refer to the identification label located on the back
panel of your player for its proper operating voltage.
* Install your player in a cabinet with adequate
ventilation holes. (7~10cm) Do not block ventilation
holes on any of the components for circulation of air.
* Do not push the disc tray by the hand.
* Do not stack components.
* Be sure to turn all components off before moving the
player.
* Before connecting other components to this player, be
sure to turn them off.
* Be sure to remove the disc and turn off the player
after use, especially if you don’t use it for a long time.
2. For your safety
* This product utilizes a laser. Use of controls or
adjustments or performance of procedures other than
those specified herein may result in hazardous
radiation exposure.
* Do not open covers and do not repair yourself.
Refer servicing to qualified personal.
3. Caution
* Your player is not intended for industrial use but for
domestic purposes. Use of this product is for
personal use only.
* Do not put any container filled with liquid or any small
metal objects on the player.
* Exterior influences such as lightning and static
electricity can affect normal operation of this player.
If this occurs, turn the player off and on again with the
POWER button, or disconnect and then reconnect the
AC power cord to the AC power outlet. The player will
operate normally.
* When condensation forms inside the player due to
sharp changes in temperature, the player may not
operate correctly. If this occurs, leave the player at
room temperature until the inside of the player
becomes dry and operational.
4. Disc
* Do not clean record-cleaning sprays, benzene,
thinner, or other volatile solvents that may cause
damage to the disc surface.
* Do not touch the disc’s signal surface. Hold by the
edges or by one edge and the hole in the center.
* Wipe the dirt away gently; never wipe a cloth back
and forth over the disc.
Before you start
CAUTION : USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Table of Contents
Setup
Accessories
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before you start . . . . . . . . . . . . . . . . . . . . . . . .3
General Features . . . . . . . . . . . . . . . . . . . . . . .4
Disc Type and Characteristics . . . . . . . . . . . . .5
Description-Front Panel . . . . . . . . . . . . . . . . . .6
Display Indicators . . . . . . . . . . . . . . . . . . . . . .6
Description-Rear Panel . . . . . . . . . . . . . . . . . .7
Tour of the Remote Control . . . . . . . . . . . . . . .8
1
EZ VIEW
STANDBY/ON
PLAY
LOADING
Remote Control
Batteries for
Remote Control
(AAA Size)
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . .9
Basic Functions
EZ VIEW
STANDBY/ON
PLAY
STANDBY/ON
EZ VIEW
PLAY
LOADING
User’s Manual
2
3
STANDBY/ON
EZ VIEW
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . .11
Using the Search & Skip Functions . . . . . . . .12
Using the Display Function . . . . . . . . . . . . . . .12
Using the Disc and Title Menu . . . . . . . . . . . .13
Using the Function Menu . . . . . . . . . . . . . . . .14
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . .14
Program Play & Random Play . . . . . . . . . . . .15
Slow Repeat play . . . . . . . . . . . . . . . . . . . . . .15
LOADING
PLAY
Video/Audio Cable
Install Batteries in the Remote
Advanced Functions
1. Open the battery cover on the back of the
remote.
2. Insert two AAA batteries. Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
Adjusting the Aspect Ratio (EZ View) . . . . . . .16
Selecting the Audio Language . . . . . . . . . . . .17
Selecting the Subtitle Language . . . . . . . . . . .17
Changing the Camera Angle . . . . . . . . . . . . .18
Using the Instant Replay/Skip Function . . . . .18
Using the Bookmark Function . . . . . . . . . . . .19
Using the Zoom Function . . . . . . . . . . . . . . . .20
How to insert a Memory Card . . . . . . . . . . . . .20
Clips Menu for MP3/WMA/JPEG . . . . . . . . . .21
Folder Selection . . . . . . . . . . . . . . . . . . . . . . .21
MP3/WMA Play . . . . . . . . . . . . . . . . . . . . . . .22
JPEG Playback . . . . . . . . . . . . . . . . . . . . . . .23
LOADING
If remote doesn’t operate properly:
4
• Check the polarity + - of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
Changing Setup menu
Using the Setup Menu . . . . . . . . . . . . . . . . . .24
Setting Up the Language Features . . . . . . . . .25
Setting Up the Audio Options . . . . . . . . . . . . .27
Setting Up the Display Options . . . . . . . . . . . .28
Setting Up the Parental Control . . . . . . . . . . .29
5
Reference
5. Environmental info
* The battery used in this product contains chemicals
that are harmful to the environment.
* So, dispose of batteries in the proper manner,
according to federal, state, and local regulations.
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .31
Specifications . . . . . . . . . . . . . . . . . . . . . . . .32
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
ENG-2
ENG-3
General Features
Disc Type and Characteristics
Excellent Sound
Note
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
* Discs which cannot be played with this player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• HD layer of super Audio CD
• CDGs play audio only, not graphics.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Programmed Play
You can program tracks to play in desired order.
(CD)
Parental Control
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
This DVD player is capable of playing the following types of discs with the corresponding
logos:
Disc Types (Logos)
Recording Types Disc Size
DVD
Audio
+
Video
* Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW
* The unit may not play certain CD-R, CD-RW and
DVD-R due to the disc type or recording
conditions.
VIDEO-CD
Audio
+
Video
EZ VIEW
Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Many DVD discs are encoded with copy
protection. Because of this, you should only
connect your DVD player directly to your TV, not to
a VCR. Connecting to a VCR results in a
distorted picture from copy-protected DVD discs.
AUDIO-CD
Single-sided 240 min. • DVD contains excellent sound and
Double-sided 480 min. video due to Dolby Digital and
MPEG-2 system.
•
Various screen and audio functions
Single-sided 80 min.
can be easily selected through the
Double-sided 160 min.
on-screen menu.
74 min.
12 Cm
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
Audio
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Disc Markings
~
PAL
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
8 Cm
Characteristics
• Video with CD sound, VHS
quality & MPEG-1 compression
technology.
COPY PROTECTION
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional
interlaced picture.
12 Cm
Max. Playing Time
Play Region Number
Play Region Number
Both the DVD player and the discs are coded by region.
These regional codes must match in order for the disc to
play. If the codes do not match, the disc will not play.
PAL broadcast system in U.K, France,
Germany, etc.
The Region Number for this player is described on the
rear panel of the player.
Dolby Digital disc
PROGRESSIVE SCAN OUTPUTS (525p/625p)
STEREO
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE, IN CASE OF 525 OR 625 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION
TO THE ‘STANDARD DEFINITION’ OUTPUT.
IF THERE ARE QUESTIONS REGARDING OUR TV
SET COMPATIBILITY WITH THIS MODEL 525p AND
625p DVD PLAYER, PLEASE CONTACT OUR
CUSTOMER SERVICE CENTER.”
MP3/WMA
This unit can play discs created from MP3/WMA files.
Instant Replay
This function is used to replay the previous
10 seconds of the movie from the current position.
Instant Skip
This function skips playback ahead 10 seconds.
Memory Card
“Memory Card” is a new compact, portable and
versatile IC (Integrated Circuit) recording medium
with a data capacity that exceeds a floppy disk.
ENG-4
DIGITAL
SOUND
• CD is recorded as a Digital
Signal with better audio quality,
less distortion and less
deterioration of audio quality
over time.
Stereo disc
Digital Audio disc
DTS disc
MP3 disc
ENG-5
Description-Front Panel
Description-Rear Panel
8
9 10
Pr
PULL OPEN
Pb
Y
STANDBY/ON
EZ VIEW
COAXIAL
COMPONENT VIDEO OUT
MULTI-CARD INPUT
OPTICAL
R
1
2
3
4
5
6
L
ANALOG AUDIO OUT
7
VIDEO OUT
S-VIDEO OUT
3
4
Front Panel Controls
1. STANDBY/ON (
)
• When the unit is first plugged in, the indicator
lights. When STANDBY/ON is pressed on again,
the light goes out and the player is turned on.
1
6. STOP (
)
• Stops disc play.
7. SKIP (
) / SEARCH
• Allows you to search forward through a disc.
Use to skip the title, chapter or track.
2. DISC TRAY
• Place the disc here.
8. OPEN/CLOSE (
)
• Press to open and close the disc tray.
3. DISPLAY
• Operation indicators are displayed here.
9. SKIP (
) / SEARCH
• Allows you to search backward through a disc.
Use to skip the title, chapter or track.
4. MULTI-CARD INPUT (See page 20)
5. EZ VIEW
• Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
10. PLAY/PAUSE (
)
• Begin or pause disc play.
2
1
2
3
6
Rear Panel
1. DIGITAL AUDIO OUT JACKS
• Use either an optical or coaxial digital cable to
connect to a compatible Dolby Digital receiver.
Use to connect to an A/V Amplifier that contains
a Dolby Digital, MPEG-2 or DTS decoder.
5. COMPONENT VIDEO OUT JACKS
• Use these jacks if you have a TV with
Component Video in jacks. These jacks provide
Pr, Pb and Y video. Along with S-Video,
Component Video provides the best picture
quality.
• If Component (P-SCAN) Video Output is
selected in Setup Menu, progressive scan mode
will work.
• If Component (I-SCAN) Video Output is selected
in Setup Menu, interlaced scan mode will work.
2. ANALOG AUDIO OUT JACKS
• Connect to the Audio input jacks of your
television, audio/video receiver.
3. VIDEO OUT JACK
• Use a video cable to connect to the Video input
jack on your television.
• The Video Output in Setup Menu must be set to
the Component (I-SCAN) or S-Video.
Display Indicators
5
6. SCART JACK
• Connect to a TV scart input jack.
4. S-VIDEO OUT JACK
• Use the S-Video cable to connect this jack to
the S-Video jack on your television for a higher
picture quality.
• The Video Output in Setup Menu must be set to
the S-Video.
Important Note
• Consult your TV User’s Manual to find out if your
TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV
User’s Manual’s instructions regarding Progressive
Scan settings in the TV’s menu system.
Front Panel Display
• If Component (P-SCAN) Video Output is selected
in Setup Menu, Video and S-Video will not work.
1. Disc type indicators
2. Play / Pause / Forward play
3. Displays various messages concerning operations such as PLAY, STOP, LOAD ...
no DISC : No disc loaded.
OPEN : The disc tray is open.
LOAD : Player is loading disc information.
• See page 29 to get more information on how to
use the setup menu.
ENG-6
ENG-7
Tour of the Remote Control
Choosing a Connection
6. STOP Button (
)
The following shows examples of connections commonly used to connect the DVD player with a TV
and other components.
7. MENU Button
• Brings up the DVD player’s setup menu.
11
1
8. RETURN Button
2
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
• Returns to a previous menu.
• Refer to the owner’s manual of the additional components you are connecting for more information on those
particular components.
9. DVD/M.CARD button
12
13
14
3
4
Connection to an Audio System
10. SUBTITLE Button
11. OPEN/CLOSE (
Before Connecting the DVD Player
) Button
• To open and close the disc tray.
Method 1
5
6
7
15
16
8
17
12. CLEAR Button
• Use to remove menus or status displays from the
screen.
13. INSTANT REPLAY Button
18
• This function is used to replay the previous 10
seconds of the movie from the current position.
AUDIO
SYSTEM
14. INSTANT SKIP Button
9
19
20
21
22
10
Method 2
2ch Amplifier
Dolby Digital Decoder
Audio Input Jacks
Digital Audio Input Jack
• This function skips playback ahead 10 seconds.
15. PLAY/PAUSE Button (
)
• Begin/Pause disc play.
16. INFO Button
• Displays the current disc mode.
17. DISC MENU Button
OR
• Brings up the Disc menu.
18. ENTER/DIRECTION Button
(UP/DOWN or LEFT/RIGHT Buttons)
• This button functions as a toggle switch.
DVD Function Buttons
19. EZ VIEW Button
1. DVD POWER Button
• Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
• Turns the power on or off.
OPTICAL
R
L
COAXIAL
ANALOG AUDIO OUT
Analog Audio Out
2. NUMBER Buttons
Digital Audio Out
20. REPEAT Button
• Allows you to repeat play a title, chapter, track, or
disc.
3. PROG Button
• Allows you to program a specific order.
21. ANGLE Button
4. STEP Button
• Use to access various camera angles on a DVD.
• Advances play one frame at a time.
5. SEARCH/SKIP Buttons (
DVD
Player
/
,
/
)
22. AUDIO Button
• Use this button to access various audio functions
on a disc.
• Allows you to search forward/backward through
a disc. Use to skip the title, chapter or track.
ENG-8
ENG-9
Choosing a Connection
Playing a Disc
7. Step Motion Play (Except CD)
Connection to a TV (For Video)
Before Play
TV (Normal, Widescreen, Projection, etc..)
• Turn on your TV and press the TV/VIDEO button
to select the video mode.
• Turn on your Audio System and select AUX, CD or
DVD.
Basic Audio
Method 1
Method 2
Method 3
Method 4
Method 5
Good
picture
Better
picture
Best
picture
Best
picture
Optimum
picture
After plugging in the player, the first time you press
the DVD POWER button, this screen comes up :
If you want to select the language, press a
NUMBER button. (This screen will only appear
when you plug in the player for the first time.)
TV
AV
Cable
Scart
Cables
(not
supplied)
S-Video
Cable
OR
Press the STEP button on the remote during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press PLAY/PAUSE (
) to resume normal play.
(You can only perform step motion play in the forward
direction.)
8. Slow Motion Play (Except CD)
Press and hold the
button on the remote during
PAUSE or STEP mode. Press again and you can select
slow motion play for 1/8, 1/4 and 1/2 of normal speed.
- No sound is heard during slow mode.
- Press PLAY/PAUSE (
) to resume normal play.
- Reverse slow motion play will not work.
Video
Cables
OR
OR
RESUME function
DVD
Player
Pr
R
ANALOG AUDIO OUT
Pb
Y
Pr
Pb
When you stop disc play, the player remembers
where you stopped, so when you press the
PLAY (
) again, it will pick up where you left off.
(unless the disc is removed or the player is
unplugged, or if you press the STOP (
) button
twice.)
Y
L
VIDEO OUT
S-VIDEO OUT
Audio Output Video Output S-Video
Jack
Jack
Jacks
COMPONENT VIDEO OUT
SCART Jack
Component Video
Jacks
(Interlace)
COMPONENT VIDEO OUT
Component Video
Jacks
(Progressive)
Method 1
DVD Player + TV with Video Input Jack
(The Video Output in Setup Menu must be set to the S-Video or SCART Output.)
Method 2
DVD Player + TV with S-Video Input Jack
(The Video Output in Setup Menu must be set to the S-Video.)
Method 3
DVD Player + TV with Scart Input Jacks (Audio & Video)
(The Video Output in Setup Menu must be set to SCART Output.)
Method 4
DVD Player + TV with interlace Scan Component Video Jacks
(The Video Output in Setup Menu must be set to the Component (I-SCAN).)
Method 5
DVD Player + TV with Progressive Scan Component Video Jacks.
(The Video Output in Setup Menu must be set to the Component (P-SCAN).)
• If you want to convert Video Output to the Progressive Scan, you have to first connect Video or S-Video on
your TV. Then select Component (P-SCAN) out of Video Output in Setup Menu. Within 10 seconds, change the
TV’s external input to 625p/525p(576p/480p or Component) and select “Yes” (See Page 29).
• If Component(P-SCAN) Video Output is selected in Setup Menu, Video and S-Video will not work.
Play
1. Press the OPEN/CLOSE button.
The STANDBY indicator light goes out and the tray
opens.
2. Place a disc gently into the tray with the disc’s
label facing up.
3. Press the PLAY/PAUSE (
) button or
OPEN/CLOSE button to close the disc tray.
4. Stopping Play
Press the STOP (
) button during play.
5. Removing Disc
Note
• If the player is left for 5 minutes in pause mode, it
will stop.
• If the player is left in the stop mode for more than
30 minutes, the power will automatically shut off.
(Automatic Power-Off Function)
• If the player is left in the stop mode for more than
one minute without any user interaction, a screen
saver will be activated. Press the PLAY (
)
button to resume normal play.
• This
icon indicates an invalid button press.
Press the OPEN/CLOSE button.
6. Pausing Play
Press the PLAY/PAUSE (
) or STEP button on the
remote during play.
- Screen stops, no sound.
- To resume, press the PLAY/PAUSE (
) button once
again.
Important Note
• Consult your TV User’s Manual to find out if your TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV User’s Manual’s instructions regarding Progressive Scan settings in the TV’s menu system.
• Depending on your TV, the Method of connection may differ from the illustration above.
ENG-10
ENG-11
Using the Search & Skip Functions
Using the Display Function
During play, you can search quickly through a
chapter or track or use the skip function to
jump to the next selection.
When Playing a DVD/VCD/CD
Searching through a Chapter or Track
2. Use the UP/DOWN buttons to select the desired
item.
Press the
or
button on the remote for more
than 1 second and press again to search at a faster
speed on a DVD, VCD or CD.
DVD 2X, 8X, 32X, 128X
VCD 4X, 8X
CD
1. During play, press the INFO button on the
remote.
3. Use the LEFT/RIGHT buttons to make the
desired setup and then press ENTER.
• You may use the number buttons of the remote
control to directly access a title, chapter or to
start the playback from the desired time.
4. To make the screen disappear, press the INFO
button again.
2X, 4X, 8X
To access the desired title when there is
Title more than one in the disc.
For example, if there is more than one
movie on a DVD, each movie will be
identified.
Using the Disc and Title Menu
Using the Disc Menu
1. During the playback of a DVD disc, press the
MENU button on the remote.
2. Select Disc Menu using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
Most DVD discs are recorded in
Chapter chapters so that you can quickly find a
specific passage (similar to tracks on an
audio CD).
Allows playback of the film from a
Time desired time. You must enter the starting
time as a reference.
Refers to the language of the film
DVD
Audio soundtrack. In the example, the
Skipping Tracks
During play, press the
Using the Display Function
DVD
or
button.
Title
01
Chapter 02
• When playing a DVD, if you press the
button, it
moves to the next chapter. If you press the
button, it
moves to the beginning of the chapter. One more press
makes it move to the beginning of the previous chapter.
Time
Audio
Subtitle
0:00:13
Using the Title Menu
Refers to the subtitle languages
2. Select Title Menu using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
1. During the playback of a DVD disc, press the
MENU button on the remote.
ENG 5.1CH
Off
ENTER
• When playing a VCD 2.0 in Menu Off mode, a VCD 1.1 or
a CD, if you press the
button, it moves to the next
track. If you press the
button, it moves to the
beginning of the track. One more press makes it move to
the beginning of the previous track.
soundtrack is played in English 5.1CH.
A DVD disc can have up to eight
different soundtracks.
Subtitle available in the disc.
You will be able to choose the subtitle
languages or, if you prefer, turn them off
from the screen.
A DVD disc can have up to 32 different
subtitles.
VCD
VCD
Track 01
• If a track exceeds 15 minutes when playing a VCD and
you press the
button, it moves forward 5 minutes.
If you press the
button, it moves backward 5 minutes.
Time 0:00:48
ENTER
Note
* When playing a VCD 2.0, you can choose MENU
ON or MENU OFF by using the DISC MENU
button.
CD
CD
Track 01
Time 0:00:48
ENTER
ENG-12
Note
* When in VCD 2.0 mode (MENU ON mode), this
function does not work. (See page 12)
Note
• Depending on the disc, the Title and Disc Menus
may not work.
• Title Menu will only be displayed if there are at
least two titles in the disc.
• You can also use the Disc Menu, using the DISC
MENU button on the remote.
• In VCD 2.0, the DISC MENU button is used to
select Menu On or Menu Off mode.
ENG-13
Using the Function Menu
Using the Function Menu
1. Press the MENU button during playback.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
3. Function selection screen appears: Info, Zoom,
Bookmark, Repeat and EZ View.
-
Info (See Page 12~13)
Zoom (See Page 20)
Bookmark (See Page 19)
Repeat (See Page 14)
EZ View (See Page 16)
Repeat Play
Program Play & Random Play
Repeat the current track, chapter, title, a
chosen section (A-B), or all of the disc.
Program Play (CD)
When playing a DVD/VCD/CD
2. Use the LEFT/RIGHT buttons to select
PROGRAM. Press the ENTER button.
1. Press the REPEAT button on the remote.
Repeat screen appears.
2. Select Chapter, Title or A-B using the
LEFT/RIGHT buttons.
• Chapter ( ) : repeats the chapter that is playing.
• Title ( T ) : repeats the title that is playing.
• A-B : repeats a segment of the disc that you select.
DVD
4. Use the UP/DOWN button to highlight one of the
5 functions. Then press the RIGHT or ENTER
button to access the function.
1. Press the PROG button.
3. Use the LEFT/RIGHT/UP/DOWN buttons to
select the first track to add to the program.
Press the ENTER button. The selection numbers
appear in the Program Order box.
4. Press the PLAY/PAUSE (
) button.
The disc will be played in programmed order.
PROGRAM
Off
01
T
01 A - B
REPEAT
Slow Repeat Play
This feature allows you slowly to repeat
scenes containing sports, dancing, musical
instruments being played etc. so you can
study them more closely.
When playing a DVD/VCD
1. During play, press the PLAY/PAUSE (
button.
)
2. Press and hold the
button on the remote
during PAUSE or STEP mode. Press again and
you can select slow motion play for 1/8, 1/4 and
1/2 of normal speed.
3. Press the REPEAT button on the remote.
Repeat screen appears.
RANDOM
ENTER
4. Select A-B using the LEFT/RIGHT buttons.
PROGRAM 01
Off
T
01
05
09
13
01
D
01 A - B
REPEAT
02
06
10
14
03
07
11
15
04
08
12
16
ENTER
ENTER
* A-B REPEAT
• Press ENTER at the point where you want the repeat
play to start (A). The B is automatically highlighted.
• Press ENTER at the point where you want the repeat
play to stop (B).
• A-B REPEAT does not allow you to set point (B) until at
least 5 seconds has elapsed after point (A) has been
set.
• To terminate the function, press the 'CLEAR' button.
Note
• You can also directly select these functions using
their respective buttons on the remote.
------
------
------
RETURN
------
Note
• DVD repeats play by chapter or title, CD and VCD
repeats play by disc or track.
• Depending on the disc, the Repeat function may
not work.
• When in VCD 2.0 mode (MENU ON mode), this
function does not work. (See page 12)
ENG-14
6. Press ENTER at the point where you want the
repeat play to stop (B).
CLEAR
Random Play (CD)
7. To return to normal play, press REPEAT again,
then press the LEFT/RIGHT buttons to select Off
and press ENTER.
1. Press the PROG button.
2. Use the LEFT/RIGHT buttons to select RANDOM.
Press the ENTER button.
PROGRAM
RANDOM
3. Press ENTER.
4. To return to normal play, press REPEAT again,
then press the LEFT/RIGHT buttons to select Off
and press ENTER.
• A-B REPEAT does not allow you to set point (B) until at
least 5 seconds has elapsed after point (A) has been
set.
Program Order
Track
VCD/CD
5. Press ENTER at the point where you want the
repeat play to start (A).
Note
• The disc will play from A to B repeatedly at the
speed you chose.
• To terminate the function, press the CLEAR
button.
• When in VCD 2.0 mode (MENU ON mode), this
function does not work. (See page 12)
Note
• Depending on the disc, the Program and Random
Play functions may not work.
• PROGRAM/RANDOM playback cannot be used if
the disc contains more than two types of file
extensions.
• This unit can support a maximum of 20
programmed tracks.
• While in playback mode, press the CLEAR button
on the remote control to cancel Programmed Play
or Random Play.
ENG-15
Adjusting the Aspect Ratio (EZ View)
Selecting the Audio Language
To play back using aspect ratio (DVD)
If you are using a 4:3 TV
Press the EZ VIEW button.
• The screen size changes when the button is
pressed repeatedly.
• The screen zoom mode operates differently
depending on the screen setting in the initial setup
menu.
• To ensure correct operation of the EZ VIEW
button, you should set the correct aspect ratio in
the initial setup (See page 28).
1. For 16:9 aspect ratio discs
• 4:3 Letter Box
Displays the content of the DVD title in 16:9
aspect ratio. The black bars will appear at the
top and bottom of the screen.
• 4:3 Pan Scan
The left and right of the screen are cut off and
displays the central portion of the 16:9 screen.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture will look vertically stretched.
If you are using a 16:9 TV
1. For 16:9 aspect ratio discs
• Wide Screen
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
Displays the content of the DVD title in 16:9
aspect ratio.
• Screen Fit
The top and bottom of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the
black bars at the top and bottom of the screen
will disappear. The picture will look vertically
stretched. (Depending on the type of disc, the
black bars may not disappear completely.)
You can select a desired language quickly and
easily with the AUDIO button.
You can select a desired subtitle quickly and
easily with the SUBTITLE button.
Using the AUDIO button
Using the SUBTITLE button
1. Press the AUDIO button.
1. Press the SUBTITLE button.
2. The Audio changes when the button is pressed
repeatedly.
2. The subtitle changes when the button is pressed
repeatedly.
- The audio languages are represented by abbreviations.
3. Press the AUDIO button to select Stereo, Left or
Right. (On VCD/CD)
3. To turn off the display, press the CLEAR or
RETURN button.
- Initially, the subtitle will not appear on screen.
- The subtitle languages are represented by
abbreviations.
DVD
ENG DOLBY DIGITAL 5.1CH
AUDIO
ENG
SUBTITLE
Off
SUBTITLE
2. For 4:3 aspect ratio discs
• Normal Screen
Displays the content of the DVD title in 4:3
aspect ratio.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture would look vertically stretched.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
VCD/CD
Stereo
AUDIO
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
2. For 4:3 aspect ratio discs
• Normal Wide
Displays the content of the DVD title in 16:9
aspect ratio. The picture will look horizontally
stretched.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture will look vertically stretched.
Selecting the Subtitle Language
Note
• This function may behave differently depending on
the type of disc.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
• Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black
bars will appear at the left and right of the
screen in order to prevent the picture from
looking horizontally stretched.
ENG-16
Note
• This function depends on what languages are
encoded on the disc and may not work with all
DVDs.
• A DVD disc can contain up to 8 audio languages.
• How to have the same audio language come up
whenever you play a DVD;
Refer to “Setting Up the Language Features” on
page 26.
Note
• This function depends on what languages are
encoded on the disc and may not work with all
DVDs.
• A DVD disc can contain up to 32 subtitle
languages.
• How to have the same subtitle language come
up whenever you play a DVD;
Refer to “Setting Up the Language Features” on
page 26.
ENG-17
Changing the Camera Angle
Using the Instant Replay/Skip Function
When a DVD contains multiple angles of a
particular scene, you can select the Angle
function.
Using the Instant Replay function (DVD)
Using the ANGLE button
If you press the INSTANT REPLAY button, the
current scene moves backward about 10 seconds,
and plays back.
Press the ANGLE button to see if an ANGLE
(
) mark is present at the upper left hand
corner of the screen.
If you miss a scene, you can see it again using
this function.
* Depending on the disc, the Instant Replay function may
not work.
Using the Bookmark Function
This feature lets you bookmark sections of a
DVD or VCD (MENU OFF mode) so you can
quickly find them at a later time.
Using the Bookmark Function (DVD/VCD)
1. During play, press the MENU button on the
remote.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
1. When an ANGLE mark is shown, press the
ANGLE button, then an ANGLE select icon will
appear at the upper hand corner of the screen.
3. Select Bookmark using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
2. Press the ANGLE button to select the desired
screen angle.
4. Use the LEFT/RIGHT buttons to move to the
desired bookmark icon.
3. To turn off the display, press the CLEAR or
RETURN button.
5. When you reach the scene you want to mark,
press the ENTER button. The icon will change to
a number (1, 2, or 3).
4/6
Recalling a Marked Scene
1. During play, press the MENU button on the
remote and select the Bookmark.
2. Use the LEFT/RIGHT buttons to select a marked
scene.
3. Press the PLAY/PAUSE (
the marked scene.
) buttons to skip to
ANGLE
Clearing a Bookmark
Using the Instant Skip function (DVD)
Use this function to skip playback about 10
seconds ahead of the current scene.
Press the INSTANT SKIP button.
- Playback will skip ahead 10 seconds.
- Depending on the disc, this function may not work.
Note
• If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
1. During play, press the MENU button on the
remote and select the Bookmark.
2. Use the LEFT/RIGHT buttons to select the
bookmark number you want to delete.
3. Press the CLEAR button to delete a bookmark
number.
Note
• Up to three scenes may be marked at a time.
• When in VCD 2.0 mode (MENU ON mode), this
function does not work. (See page 12)
• Depending on the disc, the Bookmark function may
not work.
ENG-18
ENG-19
Using the Zoom Function
Using the Zoom Function (DVD/VCD)
1. During play or pause mode, press the MENU
button on the remote.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
How to insert a Memory Card
This unit accepts 7 different types of
Memory Cards
Insert the Memory Card correctly with the label
facing up, otherwise it may not work.
3. Select Zoom using the UP/DOWN buttons, then
press the RIGHT or ENTER button.
MEMORY STICK
MEMORY STICK PRO
Clips Menu for MP3/WMA/JPEG
1. Open the disc tray.
2. Place the disc on the tray.
- Place the disc with the labeled side up.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
Smart Media
Off
4. Use the UP/DOWN or LEFT/RIGHT buttons to
select the part of the screen you want to zoom in
on.
00:00:23
1_mp3
Folder Selection
The folder can only be selected in the Stop
mode.
• To select the Parent Folder
Press the RETURN button to go to parent folder,
or use the UP/DOWN buttons to select “..” and
press ENTER to go to the parent folder.
• To select the Peer Folder
Use the LEFT/RIGHT buttons to highlight left
window. Use the UP/DOWN buttons to select the
desired folder, then press ENTER.
Secure Digital
B e c a u s e Yo u
5. Press the ENTER button.
Cactus
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
Sad Day
CF
Micro
Drive
- During VCD play, press ENTER to zoom in 2X/Normal
in order.
Multi Media
Parent Folder, Current Folder
and Peer Folders
Compact Flash
• To select the Sub-Folder
Use the LEFT/RIGHT buttons to highlight right
window. Use the UP/DOWN buttons to select the
desired folder, then press ENTER.
Root
Folders and Files in
Current Folder
WMA
Micro Drive
JPEG
•
: Name of currently playing file.
•
: Current Playback Time.
•
: Current Playback Mode : There are 4
modes, toggle by the REPEAT button.
(During playing a song)
- Off : Normal Playback
- Track : Repeats the current track.
- Folder : Repeats the current folder.
- Random : Files in the disc will be played
in random order.
Parent Folder
MP3
This device supports 7 types of memory cards :
Memory Stick, SD Card, MMC and Smart Media
Card through the upper slot and Compact Flash,
Micro Drive through the lower slot.
Note
• Memory Cards over 2GB use FAT 32, which may
be not compatible with this unit.
• If it is not fully inserted, the “Memory Card” will not
work.
• If you remove the “Memory Card” during Memory
Card operation, the recorded data may become
corrupted. It is better to remove it after pressing
DVD/M.CARD button to return to DVD/CD Mode.
• Don’t insert two or more cards at the same time.
If cards are inserted in two slots, these may not
work.
ENG-20
•
: MP3 file icon.
•
: WMA file icon.
•
: JPEG file icon.
•
: Folder icon.
•
: Current Folder icon.
•
: Disc Mode (
MUSIC
Current Folder
1st
Sub-Folders
2nd
SONG FILE 1
Peer Folders
SONG FILE 2
SONG FILE 3
: Memory Card Mode)
ENG-21
MP3/WMA Play
MP3/WMA Play
When playing a CD-R
Repeat/Random playback
CD-R / Memory Card MP3/WMA file
1. Open the disc tray.
Press the REPEAT button to change playback
mode. There are 4 modes, Off, Track, Folder and
Random.
- Off : Normal Playback
- Track : Repeats the current song file.
- Folder : Repeats the song files which have the
same extension in the current folder.
- Random : Song files which have the same
extension will be played in random
order.
When you record MP3 or WMA files on the CDR/Memory Card, please refer to the following.
* To resume normal play, press the CLEAR button.
• When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file
extension.
General name format of: Title.mp3. or Title.wma.
When composing your title, make sure that you use 8
characters or less, have no spaces in the name, and
avoid the use of special characters including: (.,/,\,=,+).
2. Place the disc on the tray.
- Place the disc with the labeled side up.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
When playing a Memory Card
1. Insert a Memory Card.
2. Press the DVD/M.CARD button on the remote.
MP3/WMA Play Function
1. Select the desired folder. (See page 21 to select
the folder)
2. Use the UP/DOWN or LEFT/RIGHT buttons to
select a song file.
3. Press ENTER to begin playback of the song file.
Off
00:00:23
1_mp3
Note
• DVD/CD cannot be played in the Memory Card
mode. If you push the DVD/M.CARD or OPEN
button in DVD/M.CARD mode, the system will
automatically enter the DVD/CD mode.
• Depending on the recording method, some MP3
CD-Rs may not be replayed.
• When pushing the DVD/M.CARD button to play
disc again, the player doesn’t remember where
you stopped.
• It is impossible to write MP3/WMA or JPEG files to
a Memory Card in this unit as it is read only.
• Only MP3/WMA Format files with the “ .mp3” and
“ .wma” extensions can be played.
B e c a u s e Yo u
Cactus
Sad Day
• Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
When playing a CD-R / Memory Card /
Picture CD
1. Select the desired folder. (See page 21 to select
the folder)
2. Use the UP/DOWN buttons to select a Picture file in
clips menu and then press the ENTER button. You
should get a screen that looks like the one below.
• Only Memory Cards with FAT16 format can be played.
• Memory Card over 2GB use FAT32, which may be not
compatible with this unit.
• Use a decompression transfer rate of at least 128
Kbps when recording MP3 files.
Sound quality with MP3 files basically depends on the rate
of compression/decompression you choose. Getting CD
audio sound requires an analog/digital sampling rate, that
is conversion to MP3 format, of at least 128 Kbps and up
to 160 Kbps. However, choosing higher rates, like 192
Kbps or more, only rarely give better sound quality.
Conversely, files with decompression rates below 128
Kbps will not be played properly.
• Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the
rate of compression/decompression you choose.
Getting CD audio sound requires an analog/digital
sampling rate, that is conversion to WMA format, of at
least 64Kbps and up to 192Kbps.
Conversely, files with decompression rates below 64Kbps
or over 192Kbps will not be played properly.
• Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected
to prevent illegal copying. These files are of the following
types: Windows MediaTM (registered trade mark of
Microsoft Inc) and SDMITM (registered trade mark of The
SDMI Foundation). You cannot copy such files.
• Important: The above recommendations cannot be taken
as a guarantee that the DVD player will play MP3
recordings, or as an assurance of sound quality. You
should note that certain technologies and methods for
MP3 file recording on CD-Rs prevent optimal playback of
these files on your DVD player (degraded sound quality
and in some cases, inability of the player to read the files).
• This unit can play a maximum of 3000 files and 300
folders per disc.
ENG-22
JPEG Playback
ENTER RETURN
• Use the INFO button on the remote control to select
the menu you want to view and then press the
ENTER button.
•
: Returns to the Album Screen.
• To see the next 6 pictures, press the
• To see the previous 6 pictures, press the
button.
button.
•
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
•
: Each time the ENTER button is pressed, the
picture is enlarged up to 4X.
(Normal ➝ 2X ➝ 4X ➝ 2X ➝ Normal)
•
: The unit enters slide show mode.
TIMER:
ENTER RETURN
•
: When this icon is selected and ENTER is
pressed, the pictures change automatically in
intervals of about a 6 second.
•
: The pictures change automatically in intervals
of about a 12 second.
•
: The pictures change automatically in intervals
of about a 18 second.
*Depending on the file size, each interval between
images may be longer or shorter.
*If you don’t press any button, the slide show starts
automatically in 5 second intervals by default.
ENG-23
JPEG Playback
Note
• If no buttons on the remote control are pressed for
10 seconds, the menu will disappear.
Press the INFO button on the remote control to
display the menu again.
• Press the STOP button to return to the clips menu.
• When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
• Every time you push the DVD/M.CARD button, the
system enters the Memory Card mode and the
DVD/CD mode in turn.
- Memory Card mode : Plays the Memory Card
- DVD/CD Mode : Plays the CD-R & Photo CD
Using the Setup Menu
The Setup menu lets you customize your DVD
player by allowing you to select various
language preferences, set up a parental level,
even adjust the player to the type of television
screen you have.
1. With the unit in Stop mode, press the MENU
button on the remote. Select Setup using
UP/DOWN buttons, then press the RIGHT or
ENTER button.
If you set the player menu, disc menu, audio
and subtitle language in advance, they will
come up automatically every time you watch a
movie.
Display Setup : Setup of the Display Options.
Use to select which type of screen you want to
watch and several display options.
CD-R / Memory Card / Picture CD JPEG
Parental Setup : Setup of the Parental Level.
Allows users to set the level necessary to
prevent children from viewing unsuitable
movies such as those with violence, adult
subject matter, etc.
Using the Disc Menu Language
This function changes the text language only on the
disc menu screens.
Using the Player Menu Language
1. With the unit in Stop mode, press the MENU
button.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
4. Select Disc Menu using UP/DOWN buttons, then
press the RIGHT or ENTER button.
Language Setup : Setup of the Language.
Audio Setup : Setup of the Audio Options.
• Only files with the “.jpg” and ‘.JPG” extensions can be
played.
• If the disc is not closed, it will take longer to start
playing and not all of the recorded files may be
played.
• Only CD-R discs with JPEG files in ISO 9660 or Joliet
format can be played.
• Memory Cards over 2GB use FAT32, which may be
not compatible with this unit.
• The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or
special characters (. / = +).
• Only a consecutively written multisession disc can be
played. If there is a blank segment in the multisession
disc, the disc can be played only up to the blank
segment.
• A maximum of 500 images can be stored on a single
CD.
• Kodak Picture CDs are recommended.
• When playing a Kodak Picture CD, only the JPEG
files in the pictures folder can be played.
• Kodak Picture CD : The JPEG files in the pictures
folder can be played automatically.
• Konica Picture CD : If you want to see the Picture,
select the JPEG files in the clips menu.
• Fuji Picture CD : If you want to see the Picture, select
the JPEG files in the clips menu.
• QSS Picture CD : The unit cannot play QSS Picture
CDs.
• If a number of files in 1 Disc are over 3000, only 3000
JPEG file can be played.
• If a number of folders in 1 Disc are over 300, only
JPEG files in 300 folders can be played.
Setting Up the Language Features
e.g) Setting up in English.
5. Use the UP/DOWN buttons to select ‘English’.
- Select “Others” if the language you want is not listed.
e.g) Setting up in English.
DISC MENU LANGUAGE
Disc Menu
4. Select Player Menu using UP/DOWN buttons,
then press the RIGHT or ENTER button.
JJJJ
Others
LANGUAGE SETUP
Disc Menu
Title Menu
Function
6. Press the ENTER button.
Setup
- English is selected and the screen returns to SETUP
menu.
5. Use the UP/DOWN buttons to select ‘English’.
2. Use the UP/DOWN buttons on the remote to
access the different features.
3. Press the ENTER or RIGHT button to access the
sub features.
PLAYER MENU LANGUAGE
Player MenuJJ
JJ
English
JJJJ
Français
JJJJ
Deutsch
JJJJ
JJJJ
JJJJ
Español
Italiano
Nederlands
To make the setup screen disappear after setting
up, press the MENU button again.
6. Press the ENTER button.
Note
Depending on the disc, some Setup Menu
selections may not work.
ENG-24
- English is selected and the screen returns to SETUP
menu.
- To make the SETUP menu disappear, press the
RETURN or LEFT button.
ENG-25
Setting Up the Language Features
Setting Up the Audio Options
Using the Audio Language
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
1. With the unit in Stop mode, press the MENU
button.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
3. Select Audio Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
4. Select Audio using UP/DOWN buttons, then
press the RIGHT or ENTER button.
4. Select Subtitle using UP/DOWN buttons, then
press the RIGHT or ENTER button.
5. Press the UP/DOWN buttons to select ‘English’.
5. Use the UP/DOWN buttons to select ‘English’.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
preference.
- Select “Others” if the language you want is not listed.
- Select “Others” if the language you want is not listed.
Some discs may not contain the language you select
as your initial language; in that case the disc will use its
original language setting.
AUDIO LANGUAGE
2. Off : Select this when the amplifier connected to the
player is 96KHz compatible. In this case, all
signals will be output without any changes.
4. Use the UP/DOWN buttons to select the desired
item. Then press the RIGHT or ENTER button.
AUDIO SETUP
JJJJ
JJJJ
JJJJ
Original
Others
Automatic
Subtitle
JJJJ
Dynamic Compression
1. On : To select dynamic compression.
2. Off : To select the standard range.
PCM Down Sampling
1. On : Select this when the amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
Audio
SUBTITLE LANGUAGE
DTS
1. Off : Doesn’t output digital signal.
2. On : Outputs DTS Bitstream via digital output only.
Select DTS when connecting to a DTS Decoder.
Dolby Digital OutputJJ
MPEG-2 Digital OutJJ
: PCM
: PCM
DTSJJJJJ
: Off
Dynamic Compression J
: On
PCM Down Sampling JJ
: On
Note
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
• Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
• “DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Others
6. Press the ENTER button.
- English is selected and the screen returns to SETUP
menu.
Dolby Digital Output
6. Press the ENTER button.
- English is selected and the screen returns to SETUP
menu.
Note
• If the selected language is not recorded on the
disc, the original pre-recorded language is
selected.
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
1. PCM : Converts to PCM(2CH) 48kHz audio. Select
PCM when using the Analog Audio Outputs.
2. Bitstream : Converts to Dolby Digital Bitstream
(5.1CH). Select Bitstream when using the
Digital Audio Output.
Note • Be sure to select the correct Digital Output or
no audio will be heard.
MPEG-2 Digital Out
1. PCM : Converts to PCM(2CH) audio. Select PCM
when using the Analog Audio Outputs.
2. Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH or 7.1CH). Select Bitstream when
using the Digital Audio Output.
ENG-26
ENG-27
Setting Up the Display Options
Setting Up the Display Options
1. With the unit in Stop mode, press the MENU button.
1. S-Video : Select when you want to use Video and
S-Video Out.
The Parental Control function works in conjunction
with DVDs that have been assigned a rating - which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
2. Component (I-SCAN) : Select when you want to use
Component Interlace
(625i/525i) Out.
1. With the unit in Stop mode, press the MENU
button.
3. Frame : Select this feature when you want to see
small letters more clearly in the Auto mode.
3. Component (P-SCAN) : Select when you want to use
Component Progressive
(625p/525p) Out.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
Screen Messages
Use to turn on-screen messages On or Off.
4. SCART Output : Select when you want to use Scart
Out.
Still Mode
These options will help prevent picture shake in still
mode and display small text clearer.
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
1. Auto : When selecting Auto, Field/Frame mode will be
automatically converted.
3. Select Display Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
2. Field : Select this feature when the screen shakes in
the Auto mode.
Black Level
Adjusts the brightness of the screen.(On/Off)
TV System
4. Use the UP/DOWN buttons to select the desired
item. Then press the RIGHT or ENTER button.
1. NTSC Disc : In case of using NTSC disc
• If your TV system only has PAL-Video input you
must choose “PAL”. When you choose “PAL”,
Interlace output format is PAL 60 Hz output.
TV Aspect
Depending on the type of television you have, you may
want to adjust the screen setting (aspect ratio).
2. PAL Disc : In case of using PAL disc
• If your TV system only has NTSC-Video input, you
must choose “NTSC Output”.
2. 4:3 Pan Scan : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture
will be cut off.)
• If your TV system only has PAL input, you must
choose “PAL Output”.
• RGB : Select when you want to use SCART RGB
Out.
• S-Video : Select when you want to use SCART
S-Video Out.
• Video : Select when you want to use SCART
Video Out.
* If the Yes/No selection in the Display Setup sub Menu
is not made within 10 seconds, the screen returns to
the previous menu.
DISPLAY SETUP
TV AspectJJJ
: 4:3 L-Box
Still ModeJJJ
: Auto
Screen MessagesJ
: On
Black LevelJJ
: Off
TV SystemJJJ
Video OutputJJ
: PAL
: S-Video
4. Use RIGHT or ENTER to select Yes if you want
to use a password. The Enter Password screen
appears.
PARENTAL SETUP
: NoJJ
DISPLAY SETUP
TV AspectJJJ
DISPLAY SETUP
: 4:3 L-Box
DISPLAY SETUP
: 4:3 L-Box
Still ModeJJJ
: Auto
Screen MessagesJ
: On
Black LevelJJ
: Off
TV SystemJJJ
Video OutputJJ
: PAL
: S-Video
S-Video
Component (I-SCAN)
ENTER
RETURN
MENU
Component (P-SCAN)
SCART Output
RGB
: Auto
S-Video
Screen MessagesJ
: On
Video
Black LevelJJ
: Off
TV SystemJJJ
Video OutputJJ
: PAL
: S-Video
Still ModeJJJ
3. Select Parental Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
Use PasswordJJ
3. 16:9 Wide : You can view the full 16:9 picture on your
widescreen TV.
TV AspectJJJ
Video Output
Select Video Output.
• If your TV system only has NTSC, input you must
choose “NTSC Output”.
1. 4:3 Letter Box : Select when you want to see the total
16:9 ratio screen DVD supplies, even though you
have a TV with a 4:3 ratio screen. Black bars will
appear at the top and bottom of the screen.
Setting Up the Parental Control
5. Enter your password. The Re-enter Password
screen appears to confirm the password.
Enter your password again.
The player is locked ( ).
Important Note
• Consult your TV User’s Manual to find out if your
TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV User’s Manual’s
instructions regarding Progressive Scan settings in
the TV’s menu system.
• If the screen is blocked by setting the wrong Video
Output, see page 31.
TV ASPECT
4:3 Letter Box
4:3 Pan Scan
16:9 Wide
ENG-28
CREATE PASSWORD
Enter Password
- - - -
0~9
ENG-29
RETURN
Setting Up the Parental Control
CREATE PASSWORD
Troubleshooting
5. Select Rating Level using UP/DOWN buttons,
and press ENTER or RIGHT button.
Before requesting service (troubleshooting), please check the following.
Problem
Re-enter Password
- - - -
0~9
• Check the batteries in the remote. They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote to reset it.
Reinstall batteries and try to operate the remote again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
5.1 channel sound is not
being reproduced.
• 5.1 channel sound is reproduced only when the following conditions are met. :
1) The DVD player is connected with the proper amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “Dolby 5.1 ch” mark
on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
P9
- To cancel the Rating Level, select No using RIGHT or
ENTER in Use Password.
e.g) Setting up in LEVEL6.
Setting Up the Rating Level
RATING LEVEL
1. With the unit in Stop mode, press the MENU
button.
Level 8 Adult
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1 Kids Safe
2. Select Setup using UP/DOWN buttons, then
RIGHT or ENTER button.
The player is locked ( ).
About the Change Password;
- Highlight Change Password using UP/DOWN buttons.
- Press ENTER button.
The Change Password screen appears.
- Enter your new password. Enter the new password again.
3. Select Parental Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
4. Enter your password.
The Parental Setup screen appears.
PASSWORD CHECK
Note
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
• If you have forgotten your password, see Forgot
Password in the Troubleshooting Guide.
- - - -
0~9
The
icon appears on
screen.
RETURN
ENG-30
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that
is out of range.
P27
P11
Disc Menu doesn’t appear.
• Check if the disc has a Menu.
Play mode differs from the
Setup Menu selection.
• Some of the functions selected in the Setup Menu may not work
properly if the disc is not encoded with the corresponding function.
The screen ratio cannot
be changed.
• The Screen Ratio is fixed on your DVDs.
P28
No audio.
• Make sure you have selected the correct Digital Output in the
Audio Options Menu.
P27
The screen is blocked
• Press power on from a cold start with no disc in the unit.
Press the SEARCH/SKIP (
) button on the front panel for 1
second. The SELECT MENU LANGUAGE display will appear.
Select the number button of the desired language.
P29
Forgot password
If you experience other
problems.
Enter Password
Page
No operations can be
performed with the remote.
RETURN
6. Select the Rating Level you want using
UP/DOWN buttons.
For example, if you select up to Level 6, discs
that contain Level 7, 8 will not play.
Action
• Press power on from a cold start with no disc in the unit.
Press the SEARCH/SKIP (
) button on the front panel for 1
second. The SELECT MENU LANGUAGE display will appear.
Select the number button of the desired language. Press the
MENU button, and then press DOWN button to select the Parental
Setup. The Parental Setup is now unlocked as
indicated on the display. You can change your password.
• Go to the contents and find the section of the instruction book that
contains the explanations regarding the current problem, and follow
the procedure once again.
• If the problem still cannot be solved, please contact your nearest
authorized service center.
ENG-31
P24~30
P29~30
Specifications
General
Power Requirements
AC 230 V, 50 Hz
Power Consumption
12 W
Weight
1.9 Kg
Dimensions
Operating Temperature Range
Operating Humidity Range
DVD
(DIGITAL VERSATILE DISC)
Disc
+5°C to +35°C
10 % to 75 %
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 8Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
Composite Video
SCART Jack
Video
Output
Component Video
S-VIDEO
SCART Jack
2 Channel
Audio
Output
430mm (W) X 205mm (D) X 50mm (H)
CD : 12Cm
(COMPACT DISC)
VCD : 12Cm
*Frequency Response
UNITED KINGDOM
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
1 channel : 1.0 Vp-p (75 Ω load)
R(Red) : 0.7 Vp-p (75 Ω load)
G(Green) : 0.7 Vp-p (75 Ω load)
B(Blue) : 0.7 Vp-p (75 Ω load)
Composite Video : 1.0 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Color Signal : 0.3 Vp-p (75 Ω load)
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Chrominance Signal : 0.3 Vp-p (75 Ω load)
2 Channel : L(1/L), R(2/R)
L(1/L), R(2/R)
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
*S/N Ratio
110 dB
*Dynamic Range
100 dB
*Total Harmonic Distortion
0.004 %
*: Nominal specification
• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
• Weight and dimensions are approximate.
ENG-32
This Samsung product is warranted for the period of twelve (12) months
from the original date of purchase, against defective materials and
workmanship. In the event that warranty service is required, you should
return the product to the retailer from whom it was purchased.
However, Samsung Authorised Dealers and Authorised Service Centers in
other EC Countries will comply with the warranty on the terms issued to
purchasers in the country concerned. In case of difficulty, details of our
Authorised Service Centers are available from:
Samsung Electronics (U.K.) Ltd.,
Euro Service Centre, Stafford Park 12,
TELFORD, Shropshire TF3 3BJ,
Tel: 0870) 242 0303, Fax: 01952) 297617
■ WARRANTY CONDITIONS
1.The warranty is only valid if, when warranty service is required, the
warranty card is fully and properly completed and is presented with the
original invoice or sales slip or confirmation, and the serial number on the
product has not been defaced.
2. Samsung’s obligations are limited to the repair or, at its discretion,
replacement of the product or the defective part.
3. Warranty repairs must be carried out by Authorised Samsung Dealers or
Authorised Service Centers. No re-imbursement will be made for repairs
carried out by non Samsung Dealers and, any such repair work and
damage to the products caused by such repair work will not be covered
by this warranty.
4. This product is not considered to be defective in materials nor
workmanship by reason that it requires adaptation in order to conform to
national or local technical or safety standards in force in any Country
other than the one for which the product was originally designed and
manufactured. This warranty will not cover, and no re-imbursement will be
made for such adaptation nor any damage which may result.
ENG-33
REPUBLIC OF
IRELAND
5. This warranty covers none of the following:
a) Periodic check ups, maintenance and repair or replacement of parts
due to normal wear and tear.
b) Cost relating to transport, removal or installation of the product.
c) Misuse, including the faiure to use this product for its normal
purposes or incorrect installation.
d) Damage caused by Lightning, Water, Fire, Acts of God, War, Public
Disturbances, incorrect mains voltage, improper ventilation or any
other cause beyond the control of Samsung.
6. This warranty is valid for any person who legally acquired possession of
the product during the warranty period.
7. The consumers statutory rights in any applicable national legislation
whether against the retailer arising from the purchase contract or
otherwise are not affected by this warranty. Unless there is national
legislation to the contrary, the rights under this warranty are the
consumers sole rights and Samsung, its subsidiaries and distributors
shall not be liable for indirect or consequential loss or any damage to
records, compact discs, videos or audio taper or any other related
equipment or material.
SAMSUNG ELECTRONICS (U.K.) LTD.
ENG-34