Download HP Openview Integration Pack User Guide

HP OpenView
Integration Pack User Guide
Release 5.1.x
Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, CA 94089
USA
408-745-2000
www.juniper.net
Part No. 162-00857-00 Rev. A00
Juniper Networks is registered in the U.S. Patent and Trademark Office and in other countries as a
trademark of Juniper Networks, Inc. Broadband Cable Processor, ERX, ESP, G1, G10, G-series,
Internet Processor, JUNOS, JUNOScript, M5, M10, M20, M40, M40e, M160, M-series, NMC-RX,
SDX, ServiceGuard, T320, T640, T-series, UMC, and Unison are trademarks of Juniper Networks,
Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the
property of their respective owners. All specifications are subject to change without notice.
Products made or sold by Juniper Networks (including the M5, M10, M20, M40, M40e, M160, and
T320 routers, T640 routing node, and the JUNOS software) or components thereof might be covered
by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S.
Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,333,650, 6,359,479, and 6,406,312.
HP OpenView Integration Pack User Guide, Release 5.1.x
Copyright © 2003, Juniper Networks, Inc.
All rights reserved. Printed in USA.
Writers: John Borelli
Editor: Fran Mues
Revision History
December 2003
The information in this document is current as of the date listed in the revision history above.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks
reserves the right to change, modify, transfer, or otherwise revise this publication without notice.
SOFTWARE LICENSE AGREEMENTa
JUNIPER NETWORKS, INC. IS WILLING TO LICENSE THE ENCLOSED SOFTWARE AND
ACCOMPANYING USER DOCUMENTATION (COLLECTIVELY, THE “PROGRAM”) TO YOU ONLY
UPON THE CONDITION THAT YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS
LICENSE AGREEMENT. PLEASE READ THESE TERMS AND CONDITIONS CAREFULLY
BEFORE COPYING OR USING THE ACCOMPANYING SOFTWARE OR INSTALLING THE
HARDWARE UNIT WITH PRE-ENABLED SOFTWARE OR USING THE ACCOMPANYING USER
DOCUMENTATION.
BY USING THE ACCOMPANYING SOFTWARE OR INSTALLING THE HARDWARE UNIT WITH
PRE-ENABLED SOFTWARE, YOU AGREE TO BE BOUND BY THE TERMS AND CONDITIONS
OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE TO BE BOUND BY THE TERMS OF
THIS LICENSE AGREEMENT, JUNIPER NETWORKS IS UNWILLING TO LICENSE THE
PROGRAM TO YOU, IN WHICH EVENT YOU SHOULD PROMPTLY WITHIN TEN (10) DAYS
FROM SHIPMENT RETURN THE UNUSED SOFTWARE, USER DOCUMENTATION, AND
RELATED EQUIPMENT AND HARDWARE TO THE PLACE OF PURCHASE AND YOU WILL
RECEIVE A FULL REFUND OF YOUR LICENSE FEE. THIS LICENSE AGREEMENT
REPRESENTS THE ENTIRE AGREEMENT CONCERNING THE PROGRAM BETWEEN YOU AND
JUNIPER NETWORKS, AND IT SUPERSEDES ANY PRIOR PROPOSAL, REPRESENTATION OR
UNDERSTANDING BETWEEN THE PARTIES.
1. License Grant. Juniper Networks, Inc. (“Juniper Networks”) and its suppliers and licensors
hereby grant to you and you hereby accept a nonexclusive, personal and nontransferable license to
use the computer software and/or hardware unit with pre-enabled software, including all patches,
error corrections, updates, and revisions thereto in machine-readable, object code form only (the
“Software”), and the accompanying User Documentation on the Juniper Networks product owned by
you and only as authorized in this License Agreement. You may make one (1) archival copy of the
Software for backup purposes provided you affix to such copy all copyright, confidentiality, and
proprietary notices that appear on the original. Except as authorized under this paragraph, no copies
of the Program or any portions thereof may be made, in whole or in part, by you or any person under
your authority or control.
The Software and User Documentation are protected under copyright laws. The title to Software and
User Documentation shall remain solely with Juniper Networks and its suppliers.
Except as authorized above, you shall not: copy, in whole or in part, the Software or the related User
Documentation; modify, reverse assemble, reverse compile, or otherwise translate, dissemble, or
obtain source code for the Software or User Documentation, in whole or in part, or permit a third party
to do so; rent, lease, distribute, sell, or create derivative works of the Software; pledge, lease, rent,
sublicense or share its rights under this License Agreement; or, without Juniper Networks’ prior
written consent, assign or transfer its rights hereunder.
2. Juniper Networks’ Rights. You agree that the Software, including the User Documentation,
embodies Juniper Networks and its suppliers' and licensors' confidential and proprietary intellectual
property protected under U.S. copyright law and you will use your best efforts to maintain their
confidentiality. You further acknowledge and agree that Juniper Networks or its suppliers and
licensors own all right, title, and interest in and to the Software, including all intellectual property
rights therein. You shall take no action inconsistent with Juniper Networks or its suppliers' ownership
of such Software. You shall not sublicense, assign, or otherwise disclose to any third party the
Software or any information about the operation, design, performance, or implementation of the
Software and User Documentation without prior written consent of Juniper Networks. You agree to
implement reasonable security measures to protect such confidential and proprietary information and
copyrighted material. This License Agreement does not convey to you an interest in or to the
Program, but only the limited right of use revocable in accordance with the terms of this License
Agreement.
3. License Fees. The license fees paid by you are paid in consideration of the license granted under
this License Agreement.
4. Term. This license is effective upon opening of the package(s) or use of the hardware containing
the Software, and shall continue until terminated. You may terminate this License at any time by
returning the Software, including any User Documentation, and all copies or portions thereof to
Juniper Networks. This License will terminate immediately without notice from Juniper Networks if
you breach any term or provision of this License. Upon such termination by Juniper Networks, you
a. If you and Juniper Networks, Inc., have executed another license agreement for the Program which
is now in effect, then such agreement (“Negotiated Agreement”) shall supersede this Software
License Agreement and shall exclusively govern the use and license terms of the Program.
must return the Software, including any User Documentation, and all copies or portions thereof to
Juniper Networks. Termination of this License Agreement shall not prejudice Juniper Networks' rights
to damages or other available remedy.
5. Limited Software Warranty: Juniper Networks warrants, for your benefit alone, that for a period
of ninety (90) days from the date of shipment from Juniper Networks that the Software substantially
conforms to its published specifications.
The limited warranty extends only to you as the original licensee. Your exclusive remedy and the
entire liability of Juniper Networks and its suppliers under this limited warranty will be, at Juniper
Networks' option, repair or replacement of the Software, or refund of the amounts paid by you under
this License Agreement. You agree that this is your sole and exclusive remedy for breach by Juniper
Networks, its suppliers or its licensors of any warranties made under this License Agreement.
In no event does Juniper Networks warrant that the Software is error free or that you will be able to
operate the Software without problems or interruptions. Juniper Networks does not warrant: 1) that
the functions contained in the software will meet your requirements; 2) that the Software will operate
in the hardware or software combination that you may select; 3) that the operation of the Software
will be uninterrupted or error free; or 4) that all defects in the operation of the Software will be
corrected.
This warranty does not apply if the product: 1) has been altered, except by Juniper Networks; 2) has
not been installed, operated, repaired, or maintained in accordance with instruction supplied by
Juniper Networks; or 3) has been subjected to or damaged by improper environment, abuse, misuse,
accident, or negligence.
EXCEPT FOR THE WARRANTIES SET FORTH ABOVE, THE SOFTWARE IS LICENSED “AS IS,”
AND JUNIPER NETWORKS DISCLAIMS ANY AND ALL OTHER REPRESENTATIONS,
CONDITIONS, AND WARRANTIES, WHETHER EXPRESS, IMPLIED, OR STATUTORY,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE OR ANY WARRANTIES FOR NONINFRINGEMENT OR
ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. ANY AND ALL SUCH
WARRANTIES ARE HEREBY EXCLUDED TO THE EXTENT ALLOWED BY APPLICABLE LAW.
JUNIPER NETWORKS' SUPPLIERS AND LICENSORS DO NOT MAKE OR PASS ON TO YOU OR
ANY THIRD PARTY ANY EXPRESS, IMPLIED, OR STATUTORY WARRANTY OR
REPRESENTATION, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY WARRANTIES FOR
NONINFRINGEMENT.
6. Proprietary Rights Indemnification. Juniper Networks shall at its expense defend you against
and, subject to the limitations set forth elsewhere herein, pay all costs and damages made in
settlement or awarded against you resulting from a claim that the Program as supplied by Juniper
Networks infringes a United States copyright or a United States patent, or misappropriates a United
States trade secret, provided that you: (a) provide prompt written notice of any such claim, (b) allow
Juniper Networks to direct the defense and settlement of the claim, and (c) provide Juniper Networks
with the authority, information, and assistance that Juniper Networks reasonably deems necessary
for the defense and settlement of the claim. You shall not consent to any judgment or decree or do
any other act in compromise of any such claim without first obtaining Juniper Networks’ written
consent. In any action based on such a claim, Juniper Networks may, at its sole option, either: (1)
obtain for you the right to continue using the Program, (2) replace or modify the Program to avoid the
claim, or (3) if neither (1) nor (2) can reasonably be effected by Juniper Networks, terminate the
license granted hereunder and give you a pro rata refund of the license fee paid for such Program,
calculated on the basis of straight-line depreciation over a five-year useful life. Notwithstanding the
preceding sentence, Juniper Networks will have no liability for any infringement or misappropriation
claim of any kind if such claim is based on: (i) the use of other than the current unaltered release of
the Program and Juniper Networks has provided or offers to provide such release to you for its then
current license fee, or (ii) use or combination of the Program with programs or data not supplied or
approved by Juniper Networks if such use or combination caused the claim.
7. Limitation of Liability. IN NO EVENT WILL JUNIPER NETWORKS OR ITS SUPPLIERS OR
LICENSORS BE LIABLE FOR ANY COST FOR SUBSTITUTE PROCUREMENT; SPECIAL,
INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR CONSEQUENTIAL DAMAGES; OR ANY
DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR PROFITS
ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE SOFTWARE, EVEN
IF JUNIPER NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Juniper Networks' cumulative liability to you or any other party for any loss or damages resulting from
any claims, demands, or actions arising out of or relating to this License Agreement shall not exceed
the total fees paid to Juniper Networks for the Software.
8. Export Control. Software, including technical data, is subject to U.S. export control laws,
including the U.S. Export Administration Act and its associated regulations, and may be subject to
export or import regulations in other countries. You agree to comply strictly with all such regulations
and acknowledge that you have the responsibility to obtain licenses to export, re-export, or import
Software.
9. Government Licensees: If any Software or associated documentation is acquired by or on
behalf of a unit or agency of the United States government, the government agrees that such
Software or documentation is a “commercial item” as that term is defined in 48 C.F.R. 2.101,
consisting of “commercial computer software” or “commercial computer software documentation” as
such terms are used in 48 C.F.R. 12.212 of the Federal Acquisition Regulations and its successors
and 48 C.F.R. 227.7202-1 through 227.7202-4 of the DoD FAR Supplement and its successors. The
use, duplication, or disclosure by the United States government of technical, data, computer software
and documentation is subject to the restrictions set forth in FAR section 12.212(a), FAR section
52.227-14(g)(2), FAR section 52.227-19, DFARS section 252.227-7015(b), DFARS section
227.7202-1(a), and DFARS section 227.7202-3(a), as applicable. All United States government end
users acquire the Software with only the rights set forth in this License Agreement.
10. General: This License shall be governed by and construed in accordance with the laws of the
Commonwealth of Massachusetts, United States of America, as if performed wholly within the state
and without giving effect to the principles of conflict of law. Any dispute arising out of this Agreement
shall be referred to an arbitration proceeding in Boston, Massachusetts, in accordance with the
commercial arbitration rules of the American Arbitration Association (the “AAA”). If the parties cannot
agree upon an arbitrator, arbitration shall be conducted by a neutral arbitrator selected by the AAA
who is knowledgeable in electronics equipment manufacturing and software licensing. The parties
shall share the procedural costs of arbitration equally, and each party shall pay its own attorneys'
fees and other costs and expenses associated with the arbitration, unless the arbitrator decides
otherwise. The arbitrator's award shall be in writing and shall include a statement of reasons, but the
arbitrator shall not be permitted to award punitive or indirect damages. The arbitrator's decision and
award shall be final and binding and may be entered in any court having jurisdiction. The terms of
this section shall not prevent any party from seeking injunctive relief in any court of competent
jurisdiction in order to protect its proprietary and confidential information. If any term or provision
hereof is found to be void or unenforceable by a court of competent jurisdiction, the remaining
provisions of this License Agreement shall remain in full force and effect. This License Agreement
constitutes the entire agreement between the parties with respect to the use of the Software and
User Documentation and supersedes any and all prior oral or written agreements, discussions,
negotiations, commitments, or understandings. No amendment, modification, or waiver of any
provision of this License Agreement will be valid unless in writing and signed by the authorized
representative of the party against which such amendment, modification, or waiver is sought to be
enforced. The waiver by either party of any default or breach of this License Agreement shall not
constitute a waiver of any other or subsequent default or breach. This License Agreement shall be
binding upon the parties and their respective successors and permitted assigns.
Should you have any questions about this agreement, please contact:
Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, CA 94089
Attn: Contracts Administrator
Contents
About This Guide
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Web Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Comments About the Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Contacting Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
Chapter 1
Overview
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Devices Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Sun Solaris Workstations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Windows Workstations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Chapter 2
Installing and Uninstalling HP OpenView Integration Pack
Before Installing HPOV Integration Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Installing and Uninstalling on a Sun Solaris Workstation . . . . . . . . . . . . . . . . . . . . 2-1
Installing HPOV Integration Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Uninstalling HPOV Integration Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Installing and Uninstalling on a Windows Workstation . . . . . . . . . . . . . . . . . . . . . 2-2
Installing HPOV Integration Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Uninstalling HPOV Integration Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
viii
Contents
Chapter 3
Using HP OpenView Integration Pack
Custom Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
SNMP Trap Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Browsing MIBs and Collecting SNMP Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Configuring Juniper Networks Devices with the NMC-RX Application . . . . . . . . 3-3
Launching the NMC-RX Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Appendix A
MIBs and Traps
MIB Files Installation Directories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
MIB Files for Juniper Networks Devices and Software . . . . . . . . . . . . . . . . . . . . . A-1
Shared/Common Standard MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
E-Series MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
M-Series and T-Series MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
SDX MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
HPOV Default MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
SNMP Traps for Juniper Networks Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
E-Series Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
E-Series Standard Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-6
E-Series Juniper Networks Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-10
M-Series and T-Series Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-12
M-Series and T-Series Standard Traps . . . . . . . . . . . . . . . . . . . . . . . . . A-12
M-Series and T-Series Juniper Networks Traps . . . . . . . . . . . . . . . . . . . A-13
SDX Software Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-14
SDX Software Juniper Networks Traps . . . . . . . . . . . . . . . . . . . . . . . . . A-14
About This Guide
Note: If the information in the HP OpenView Integration Pack Release Notes
differs from the information in this guide, follow the HP OpenView Integration Pack
Release Notes.
Introduction
HP OpenView Integration Pack is powered by the HP OpenView
Network Node Manager (HPOV NNM) platform. It includes
customizations that provide configuration and fault management for the
Juniper Networks E-series routers, the SDX software, and the M-series
and T-series routing platforms.
This user guide includes:
• An introduction and product overview
• Workstation requirements (hardware and software) for workstations on
which HP OpenView Integration Pack is installed
• Installation and removal procedures for HP OpenView
Integration Pack
• Description and user procedures for HP OpenView
Integration Pack
• An appendix describing MIB files installed with HP OpenView
Integration Pack and SNMP traps supported by HP OpenView
Integration Pack
Audience
This guide is intended for experienced system and network specialists who
will install and use HP OpenView Integration Pack.
x
About This Guide
Conventions
Table 1 and Table 2 list all the conventions used in the documentation.
Table 1 defines notice icons. Table 2 shows text conventions used
throughout the book.
Table 1 Notice icons
Icon
Meaning
Description
Informational note
Indicates important features or instructions.
Caution
Indicates that you may risk losing data or damaging your hardware.
Warning
Alerts you to the risk of personal injury.
Table 2 Text conventions
Convention
Description
Examples
Bold typeface
Represents commands and
keywords in text.
•
Command example:
Issue the clock source command.
•
Keyword example:
Specify the keyword exp-msg.
Bold Courier typeface
Represents text that the user must
type.
user input
Key name in angle brackets
Indicates the name of a key on the
keyboard.
Press <Enter>.
Key names linked with a plus sign
(+) in angle brackets.
Indicates that you must press two or
more keys simultaneously.
Press <Ctrl+B>.
Plain Courier typeface
Represents information as displayed
on your terminal’s screen.
host1#show ip ospf 2
Routing Process OSPF 2 with
Router ID 5.5.0.250
Router is an Area Border
Router (ABR)
Italics
•
Emphasize words.
•
Identify variables.
•
Identify chapter, appendix, and
book names.
•
There are two levels of access,
user and privileged.
•
clusterId, ipAddress.
•
Appendix A, System Specifications.
Documentation
HP OpenView Integration Pack
Documentation
Contact your sales representative for the latest documentation from
Juniper Networks, Inc. With each software release, we provide the HP
OpenView Integration Pack Documentation CD. The documentation
CD contains the document set in PDF format and HTML format (with
and without frames). From the HTML files, you can also access PDF files
of individual chapters and appendixes.
The documentation is also available on the Web. You can order a set of
printed documents from your Juniper Networks sales representative.
Release Notes
Release notes are included on the corresponding software CD and are
available on the Web.
In the Release Notes, you will find the latest information about features,
changes, known problems and resolved problems. If the information in
the Release Notes differs from the information found in the
documentation set, follow the Release Notes.
Web Access
To view the documentation on the Web, go to:
http://www.juniper.net/techpubs/
Additional documentation on the HP Openview application is available
through Hewlett Packard Company.
Comments About the Documentation
We encourage you to provide feedback, comments, and suggestions so
that we can improve the documentation to better meet your needs. Please
e-mail your comments to:
• [email protected]
Along with your comments, be sure to indicate:
• Document name
• Document part number
• Page number
• Software release version
xi
xii
About This Guide
Contacting Customer Support
For technical support, contact Juniper Networks at [email protected],
or at 1-888-314-JTAC (within the United States) or 408-745-9500 (from
outside the United States).
Overview
1
HP OpenView Integration Pack provides advanced configuration
management of Juniper Networks routers. It is powered by the HP
OpenView Network Node Manager platform, and is used in conjunction
with the Juniper Networks NMC-RX element manager.
The NMC-RX application configures and manages Juniper Networks
devices in a network managed by HP OpenView (HPOV). The
NMC-RX application can be launched from HPOV.
Features
HP OpenView Integration Pack provides the following main features:
• The NMC-RX application can be launched from the HPOV network
map or the NMC-RX application Tools menu
• Juniper Networks E-series router, M-series and T-series routing
platform, and SDX software MIB files can be loaded and installed in
an SNMP directory
• Custom icons for E-series devices and M-series and T-series routing
platforms can be used in the network map
• Plain language descriptions of SNMP traps can be generated for
Juniper Networks devices in a network
• SNMP trap support exists for:
> E-series routers
> M-series and T-series routing platforms
> SDX software
1-2
CHAPTER 1
Overview
System Description
HP OpenView Integration Pack provides integration software that
leverages the strengths of HPOV for device management.
Figure 1-1 shows an example of a network management system
architecture. HP OpenView Integration Pack enables you to manage
Juniper Networks devices and software from HPOV. From HPOV,
network operators can access a network map showing all Juniper devices
discovered on the network. Operators also have access to the alarm
browser, the SNMP MIB browser, and the data presenter, and can
launch the NMC-RX application from HPOV.
HP OpenView
HP OpenView
Integration Pack
NMC-RX
Application
Juniper Networks
router
Figure 1-1 Relationship of HP OpenView Integration Pack and associated components
Devices Supported
HP OpenView Integration Pack Release 5.1 supports devices using:
• E-series software Releases 4.0.x, 4.1.x, 5.0.x, and 5.1.x
• M-series and T-series routing platform software Release 6.0
• SDX software Release 4.1
System Requirements
HP OpenView Integration Pack and HP OpenView run on the same
workstation, either a Sun Solaris or a Windows workstation. To run HP
OpenView Integration Pack, the workstation must meet specific
hardware and software requirements, in addition to the hardware and
software requirements for running the HP OpenView application.
System Requirements
HP OpenView Integration Pack
Hardware Requirements
The workstation on which you install HP OpenView Integration Pack
must be the same workstation that runs HP OpenView. The workstation
must meet all hardware requirements for HP OpenView and must meet
the following additional hardware requirements:
• CD-ROM drive
• 100 MB free hard disk space
Software Requirements
This section describes the software requirements for a Sun Solaris or
Windows workstation on which you install HP OpenView Integration
Pack.
If you intend to configure nodes by using the NMC-RX application, you
must install a version of it that is compatible with your device software.
The workstation on which you install HP OpenView Integration Pack
must be the same workstation that runs HP OpenView. The workstation
must meet all software requirements for HP OpenView, and must have
the following software installed:
Sun Solaris Workstations
• Sun Solaris, version 2.7 or higher
• HP OpenView Network Node Manager for Solaris, version 6.2
• HPOV patches: PSOV_03184 and PSOV_03271
Visit the HPOV Web site for more information
(www.openview.hp.com)
Windows Workstations
• Windows NT 4.0 Service Pack 4+ or Windows 2000
• HP OpenView Network Node Manager for Windows, version 6.2
• HPOV patches: NNM_00932 and NNM_00999
Visit the HPOV Web site for more information
(www.openview.hp.com)
1-3
1-4
CHAPTER 1
Overview
Installing and Uninstalling
HP OpenView Integration
Pack
2
You can install HP OpenView Integration Pack on either Sun Solaris or
Windows workstations that meet system requirements.
Before Installing HPOV Integration Pack
Be sure all related HPOV processes are running on the target machine
before installing HP Openview Integration Pack. Follow these
preinstallation steps to ensure a proper installation:
1
Start Network Node Manager (NNM) and be sure it is installed and
running properly.
2
After you have confirmed NNM is running properly, close the
application.
3
Run the ovstatus command to verify that the ovwdb daemon is
running. If it is not running, run the ovstart command.
Installing and Uninstalling on a Sun Solaris Workstation
The following two sections discuss installing and uninstalling HP
OpenView Integration Pack on a Sun Solaris workstation.
Installing HPOV Integration Pack
Before installing HP OpenView Integration Pack on your workstation,
you must first install HP OpenView NNM 6.2.
The NMC-RX element management system does not need to be installed
for the HP OpenView Integration Pack to run. However, if you do install
or uninstall the NMC-RX application after installing the HP OpenView
2-2
CHAPTER 2
Installing and Uninstalling HP OpenView Integration Pack
Integration Pack, you must fully reinstall the HP OpenView Integration
Pack. You can monitor the installation process by viewing the following
log files in $OV_LOG/:
• cminstall_log
• Juniper_HP_Openview_Integration_Pack_Release_5.1.0_InstallLog.log
To install HP OpenView Integration Pack:
1
Insert the HP OpenView Integration Pack CD in your CD drive and
run UXCMinstall.bin.
2
Follow the instructions that appear on the screen.
3
When the installation is finished, click Done.
Uninstalling HPOV Integration Pack
You can monitor the uninstallation process by viewing the following log
file in $OV_LOG/:
• cmuninstall_log
To uninstall HPOV Integration Pack from a Sun Solaris workstation:
1
Navigate to the following directory and run the script:
• /opt/OV/JuniperHPOVIntegration/CMuninstall.sh
Note: It may take a few minutes before the uninstall dialog box appears as the
application gathers required information on the installation.
2
Once the About to Uninstall dialog box appears, click Uninstall.
Installing and Uninstalling on a Windows Workstation
The following two sections discuss installing and uninstalling HP
OpenView Integration Pack on a Windows workstation.
Installing HPOV Integration Pack
Before installing HP OpenView Integration Pack on your workstation,
you must first install HP OpenView NNM.
The NMC-RX application does not need to be installed for the HP
OpenView Integration Pack to run. However, if you do install or uninstall
the NMC-RX application after installing the HP OpenView Integration
Pack, you must fully reinstall the HP OpenView Integration Pack.
Installing and Uninstalling on a Windows Workstation
HP OpenView Integration Pack
You can monitor the installation process by viewing the following log files
in %OV_LOG%\:
• cm_installation.log
• Juniper_HP_Openview_Integration_Pack_Release_5.1.0_InstallLog.log
Note: Before installing HP OpenView Integration Pack, ensure that you followed all
preinstallation steps, such as installing Microsoft SNMP Agent. See the previous
section.
To install the HP OpenView Integration Pack:
1
Insert the HP OpenView Integration Pack CD in your CD drive. If
the installation program does not autoplay, double-click
WindowsCMinstall.exe.
2
Follow the instructions that appear on the screen.
Note: When prompted, install the Integration Pack in the same location that HP
OpenView NNM was installed.
3
When the application is installed, reboot your system.
Uninstalling HPOV Integration Pack
You can monitor the uninstallation process by viewing the following log
file in %OV_LOG%\:
• cm_uninstallation.log
To uninstall HPOV Integration Pack from a Windows workstation:
1
Navigate to the following directory and run the script.
• %OV_Main_Path%\JuniperHPOVIntegration\
CMuninstall.bat
Note: It may take a few minutes before the uninstall dialog box appears as the
application gathers required information on the installation.
2
Once the About to Uninstall dialog box appears, click Uninstall.
2-3
2-4
CHAPTER 2
Installing and Uninstalling HP OpenView Integration Pack
Using HP OpenView
Integration Pack
3
This section describes the basic operation of the HP OpenView
Integration Pack.
Custom Icons
HP OpenView Integration Pack contains custom icons for the E-series
routers and the M-series and T-series routing platforms. These icons
appear on the HP OpenView network map and are installed in the
following directory:
• Sun Solaris: $OV_BITMAPS/C/Juniper
• Windows: %OV_BITMAPS%\C\Juniper
Note: For the definition of the OpenView environment variables ($OV_BITMAPS
for Solaris and %OV_BITMAPS% for Windows), refer to the HP OpenView
manuals.
HP OpenView Integration Pack recognizes E-series, M-series, and
T-series routers during autodiscovery. When HP OpenView Integration
Pack recognizes a router it displays the appropriate icon, like the ones
shown in Figure 3-1.
Figure 3-1 Custom icons for Juniper Networks devices
3-2
CHAPTER 3
Using HP OpenView Integration Pack
SNMP Trap Descriptions
HP OpenView Integration Pack supplies plain language translations of
SNMP traps (alarms) generated by the devices. These plain language
descriptions appear automatically in the HP OpenView alarm browser
when HP OpenView receives events from devices (see Figure 3-2).
The default severity levels of each trap are only recommendations by
Juniper Networks. The severity fields are user-configurable through the
Event Configuration option within Network Node Manager. Juniper
Networks recommends that these severities be tailored based on your
specific network environment.
Figure 3-2 HPOV plain language alarm descriptions example
See Appendix A, MIBs and Traps, for a complete list of alarms that can
be generated by Juniper Networks devices. Plain language descriptions
can be viewed in the following directories and files:
Sun Solaris:
• $OV_MAIN_PATH/JuniperHPOVIntegration/conf/
> erxTrapd.conf
> mtTrapd.conf
> sdxTrapd.conf
> sdxTrapd.conf.v2c
Windows:
• %OV_MAIN_PATH%\JuniperHPOVIntegration\conf\
> erxTrapd.conf
> mtTrapd.conf
> sdxTrapd.conf
> sdxTrapd.conf.v2c
Browsing MIBs and Collecting SNMP Statistics
HP OpenView Integration Pack
Browsing MIBs and Collecting SNMP Statistics
As a system operator, you can:
• Browse SNMP MIBs
For more information, see the Hewlett-Packard guide, Managing Your
Network with HP OpenView Network Node Manager, “Customizing
Events: Doing It Your Way.”
• Collect SNMP statistics
For more information, see the Hewlett-Packard guide, Managing Your
Network with HP OpenView Network Node Manager, “Using Event
Data.”
For more information on MIBs and traps supported by HP OpenView
Integration Pack, see Appendix A, MIBs and Traps.
Configuring Juniper Networks Devices with the NMC-RX
Application
You can configure and manage only E-series devices with the NMC-RX
application through HP OpenView Integration Pack. M-series and
T-series platforms can only be viewed. Menus are added to HP
OpenView that allow you to launch the NMC-RX application.
Note: HP OpenView Integration Pack also allows you to configure E-series devices
directly by the Juniper Networks command line interface. For more information on
configuring E-series routers, see the E-Series Configuration Guides.
Note: M-series and T-series routing platforms can be viewed in the Network
Workshop. They cannot be configured in the Device Workshop.
For more information on configuring or managing parameters, see the
NMC-RX User Guide or the NMC-RX Online Help.
Launching the NMC-RX Application
To launch the NMC-RX application from HP OpenView:
1
Ensure that the following NMC-RX components are running:
• Sybase Adaptive Server Anywhere database
• Polling server
• ConfigSync server
2
Select a node on the HP OpenView network map.
3-3
3-4
CHAPTER 3
Using HP OpenView Integration Pack
3
Right-click the node and select NMC-RX from the menu.
Depending on the node type selected, the NMC-RX application
launches and displays either the Device Workshop (E-series) or
Network Workshop (M-series and T-series platform).
MIBs and Traps
A
This appendix lists the Management Information Base (MIB) files and
the SNMP traps installed with HP OpenView Integration Pack on Sun
Solaris and Windows workstations for Juniper Networks devices.
The MIB files are supported in:
• E-series software Release 5.1
• M-series and T-series routing platform software Release 6.0
• SDX software Release 4.1
MIB Files Installation Directories
MIBs are installed in the following directory:
• Sun Solaris workstations – $OV_SNMP_MIBS/Vendor/Juniper/
• Windows workstations – %OV_SNMP_MIBS%\Vendor\Juniper
MIB Files for Juniper Networks Devices and Software
The HPOV software, E-series routers, M-series and T-series platforms,
and SDX software share several MIBs and also have their own
product-specific MIBs.
Refer to the following tables for a list of supported MIB files.
Shared/Common MIBs:
• Table A-1: Shared/common standard MIBs
E-series MIBs:
• Table A-2: E-series standard MIBs
A-2
APPENDIX A
MIBs and Traps
• Table A-3: E-series Juniper Networks MIBs
M-series and T-series MIBs:
• Table A-4: M-series and T-series standard MIBs
• Table A-5: M-series and T-series Juniper Networks MIBs
SDX MIBs:
• Table A-6: SDX Juniper Networks MIBs
•
HPOV MIBs:
• Table A-7: HPOV default MIBs
Shared/Common Standard MIBs
Table A-1 Shared/common standard MIBs
M-series and T-series
MIB Name
E-series MIB Name
IANA-RTPROTO-MIB.mib
IANA-RTPROTO-MIB.mib
E-series
IANAifType-MIB.mib
IANAifType-MIB.mib
E-series
bgpmib.mib
draft-ietf-idr-bgp4-mib-07.mi2
E-series
igmpmib.mib
rfc2933.mi2
E-series
ospf2mib.mib
rfc1850.mi2 and rfc1850t.mi2
E-series
pimmib.mib
rfc2934.mi2
E-series
Rfc1213-MIB-II
rfc1213.mib
rfc1213.mib
E-series
Rfc1907-SNMPv2-MIB
rfc1907.mib
rfc3418.mi2
E-series
Rfc2011-IP-MIB
rfc2011a.mib
rfc2011.mi2
E-series
Rfc2012-TCP-MIB
rfc2012a.mib
rfc2012.mi2
E-series
Rfc2013-UDP-MIB
rfc2013a.mib
rfc2013.mi2
E-series
rfc2115a.mib
rfc2115.mi2
E-series
rfc2493.mib
rfc2493.mi2
E-series
rfc2514.mib
rfc2514.mi2
E-series
rfc2515a.mib
rfc2515.mi2
E-series
rfc2571.mib
rfc3411.mi2
rfc2572.mib
rfc3412.mi2
E-series
rfc2574.mib
rfc3414.mi2
E-series
rfc2575.mib
rfc3415.mi2
E-series
rfc2787a.mib
rfc2787.mi2
E-series
HPOV Preload
IANAifType-MIB
SDX MIB
Name
V3-arch.my
MIB That
Is Loaded
E-series
MIB Files for Juniper Networks Devices and Software
HP OpenView Integration Pack
Table A-1 Shared/common standard MIBs (continued)
HPOV Preload
Rfc2863-IF-MIB
M-series and T-series
MIB Name
E-series MIB Name
SDX MIB
Name
MIB That
Is Loaded
rfc2851.mib
rfc3291.mi2
E-series
rfc2863a.mib
rfc2863.mi2
E-series
rfc2925a.mib
rfc2925p.mi2
E-series
rfc2932.mib
rfc2932.mi2
E-series
rtmib.mib
rfc2096.mi2
E-series
rfc2665a.mib
rfc2358.mi2
M/T-series
rfc2465.mib
rfc2465tc.mi2
M/T-series
rfc2558a.mib
rfc2558.mi2
M/T-series
rfc2790a.mi2
rfc2790.mi2
M/T-series
rfc2925b.mi2
rfc2925t.mi2
M/T-series
E-Series MIBs
See the following tables for a list of E-series standard and Juniper
Networks MIBs.
Table A-2 E-series standard MIBs
IANA-ADDRESS-FAMILY-NUMBERS-MIB.mi2
rfc1406.mib
rfc2737.mi2
af-nm-0095_001_mib.mi2
rfc1407.mib
rfc2925n.mi2
draft-ietf-atommib-atm2-15.mi2
rfc1471.mib
rfc3014.mi2
draft-ietf-atommib-sonetaps-mib-05-juni.mi2
rfc1473.mib
rfc3413n.mi2
draft-ietf-disman-event-mib-v2-01.mi2
rfc1493.mib
rfc3413t.mi2
draft-ietf-idmr-dvmrp-mib-11-juni.mi2
rfc1724.mi2
rfc3419.mi2
rfc1158.mib
rfc2513.mi2
Table A-3 E-series Juniper Networks MIBs
juniAaa.mi2
juniAcctng.mi2
juniAddrPool.mi2
juniAtm.mi2
juniAutoconf.mi2
juniBgp.mi2
juniBridge.mi2
juniBridgeEthernet.mi2
juniBridgingMgr.mi2
juniCbf.mi2
juniCli.mi2
juniCops.mi2
juniDhcp.mi2
juniDhcpv6.mi2
juniDns.mi2
juniDs1.mi2
juniDs3.mi2
juniDvmrp.mi2
juniErxRegistry.mi2
juniErxSystem.mi2
juniEthernet.mi2
juniExperiment.mi2
juniFileXfer.mi2
juniFr.mi2
A-3
A-4
APPENDIX A
MIBs and Traps
Table A-3 E-series Juniper Networks MIBs (continued)
juniFt1.mi2
juniHdlc.mi2
juniHost.mi2
juniIf.mi2
juniIgmp.mi2
juniIp.mi2
juniIpPolicy.mi2
juniIpTunnel.mi2
juniIsIs.mi2
juniL2tp.mi2
juniL2tpDialout.mi2
juniLog.mi2
juniMRouter.mi2
juniMibs.mi2
juniMpls.mi2
juniOspf.mi2
juniPim.mi2
juniPolicy.mi2
juniPpp.mi2
juniPppoe.mi2
juniProducts.mi2
juniQos.mi2
juniRadClient.mi2
juniRadDiscon.mi2
juniRegistry.mi2
juniRouter.mi2
juniSlep.mi2
juniSmds.mi2
juniSmi.mi2
juniSnmp.mi2
juniSonet.mi2
juniSscClient.mi2
juniSubscriber.mi2
juniSystem.mi2
juniSystemClock.mi2
juniTc.mi2
juniTcsClient.mi2
juniTmpl.mi2
juniTmplAtm.mi2
juniTmplIp.mi2
juniTmplIpv6.mi2
juniTmplPpp.mi2
juniTmplPppoe.mi2
juniV35.mi2
M-Series and T-Series MIBs
See the following tables for a list of M-series and T-series standard and
Juniper Networks MIBs.
Table A-4 M-series and T-series standard MIBs
802.3ad.mib
mplstcmib.mib
rfc2851.mib
ggsn.mib
mroutemib.mib
rfc2856a.mib
ilmim.mib
rfc2287a.mib
rfc3020.mib
isismib.mib
rfc2495a.mib
vpntcmib.mib
l3vpnmib.mib
rfc2496a.mib
ldpmib.mib
rfc2819a.mib
Table A-5 M-series and T-series Juniper Networks MIBs
mib-jnx-atm-cos.txt
mib-jnx-atm.txt
mib-jnx-bgpmib2.txt
mib-jnx-cfgmgmt.txt
mib-jnx-chas-defines.txt
mib-jnx-chassis-alarm.txt
mib-jnx-chassis.txt
mib-jnx-cos.txt
mib-jnx-dcu.txt
mib-jnx-exp.txt
mib-jnx-firewall.txt
mib-jnx-if-extensions.txt
mib-jnx-ipv4.txt
mib-jnx-ipv6.txt
mib-jnx-ldp.txt
mib-jnx-mac.txt
mib-jnx-mpls.txt
mib-jnx-ping.txt
MIB Files for Juniper Networks Devices and Software
HP OpenView Integration Pack
Table A-5 M-series and T-series Juniper Networks MIBs (continued)
mib-jnx-pmon.txt
mib-jnx-rmon.txt
mib-jnx-rpf.txt
mib-jnx-scu.txt
mib-jnx-smi.txt
mib-jnx-sonet.txt
mib-jnx-sonetaps.txt
mib-jnx-traceroute.txt
mib-jnx-vpn.txt
SDX MIBs
See the following table for a list of SDX Juniper Networks MIBs. There
are no SDX standard MIBs.
Table A-6 SDX Juniper Networks MIBs
nxSdx.mi2
jnxSdxDes.mi2
jnxSdxGw.mi2
jnxSdxLic.mi2
jnxSdxMibs.mi2
jnxSdxPom.mi2
jnxSdxSsp.mi2
jnxSdxTc.mi2
jnxSdxTrap.mi2
jnxSdxWorkflow.mi2
ussmi.mi2
HPOV Default MIBs
See the following table for a list of HPOV default MIBs.
Table A-7 HPOV default MIBs
Rfc1902-SNMPv2-SMI
Rfc1906-SNMPv2-TM
Rfc1903-SNMPv2-TC
Dmtf-dmi.mib
Hp-unix
A-5
A-6
APPENDIX A
MIBs and Traps
SNMP Traps for Juniper Networks Devices
This section lists SNMP traps that support Juniper Networks devices.
Traps are defined in the file trapd.conf.
Refer to the following tables for a list of traps for each MIB.
E-series traps:
• Table A-8: E-series standard traps
• Table A-9: E-series Juniper Networks traps
M-series and T-series traps:
• Table A-10: M-series and T-series standard traps
• Table A-11: M-series and T-series Juniper Networks traps
SDX software traps:
• Table A-12: SDX software (version 1) Juniper Networks traps
• Table A-12: SDX software (version 2) Juniper Networks traps
E-Series Traps
See the following sections for a list of E-series standard traps and Juniper
Networks traps.
E-Series Standard Traps
E-series standard traps are defined in the MIB files listed in Table A-8.
Unless otherwise noted, the alarm type for these traps is “Juniper
Alarms.”
Table A-8 E-series standard traps
MIB Name
Trap Name
OID
Severity
af-nm-0095_001_mib.mi2
atmfM4IfAisAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.1
Major
atmfM4IfLcdAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.2
Major
atmfM4IfLofAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.3
Major
atmfM4IfLopAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.4
Major
atmfM4IfLosAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.5
Major
atmfM4IfPayloadMismatchAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.6
Major
atmfM4IfXmissionErrAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.7
Major
atmfM4IfPathTraceMismatchAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.8
Major
atmfM4IfRdiAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.9
Major
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-8 E-series standard traps (continued)
MIB Name
af-nm-0095_001_mib.mi2
af-nm-0095_001_mib.mi2
Trap Name
OID
Severity
atmfM4IfSignalLabelMismatchAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.10
Major
atmfM4VplTpAisAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.11
Major
atmfM4VplTpRdiAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.12
Major
atmfM4VpcTpAisAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.13
Major
atmfM4VpcTpRdiAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.14
Major
atmfM4VclTpAisAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.15
Major
atmfM4VclTpRdiAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.16
Major
atmfM4VccTpAisAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.17
Major
atmfM4VccTpRdiAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.18
Major
atmfM4HwBackPlaneAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.19
Major
atmfM4HwCallEstErrAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.20
Major
atmfM4HwCongestionAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.21
Major
atmfM4HwExtIfDevProbAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.22
Major
atmfM4HwLineCardAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.23
Major
atmfM4HwMultiplexerAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.24
Major
atmfM4HwPowerAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.25
Major
atmfM4HwProcessorAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.26
Major
atmfM4HwProtectionPathAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.27
Major
atmfM4HwReceiverFailAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.28
Major
atmfM4HwPIUnitMissingAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.29
Major
atmfM4HwPIUnitProbAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.30
Major
atmfM4HwPIUnitMismatchAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.31
Major
atmfM4HwTimingProbAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.32
Major
atmfM4HwXmitterFailAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.33
Major
atmfM4HwTrunkCardAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.34
Major
atmfM4HwStorageCapacityAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.35
Major
atmfM4HwMemoryMismatchAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.36
Major
atmfM4HwCorruptDataAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.37
Major
atmfM4HwSwEnvironAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.38
Major
atmfM4HwSwDownloadFailAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.39
Major
atmfM4HwVersionMismatchAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.40
Major
atmfM4HwFanFailAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.41
Major
atmfM4HwDoorOpenAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.42
Major
atmfM4HwFuseFailAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.43
Major
A-7
A-8
APPENDIX A
MIBs and Traps
Table A-8 E-series standard traps (continued)
MIB Name
af-nm-0095_001_mib.mi2
af-nm-0095_001_mib.mi2
Trap Name
OID
Severity
atmfM4HwHighTempAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.44
Major
atmfM4SwVersionMismatchAlarm
.1.3.6.1.4.1.353.5.1.3.1.2.0.45
Major
atmfM4VplTpUp
.1.3.6.1.4.1.353.5.1.3.1.2.0.46
Normal
atmfM4VplTpDown
.1.3.6.1.4.1.353.5.1.3.1.2.0.47
Major
atmfM4VclTpUp
.1.3.6.1.4.1.353.5.1.3.1.2.0.48
Normal
atmfM4VclTpDown
.1.3.6.1.4.1.353.5.1.3.1.2.0.49
Major
atmfM4VplXConnUp
.1.3.6.1.4.1.353.5.1.3.1.2.0.50
Normal
atmfM4VplXConnDown
.1.3.6.1.4.1.353.5.1.3.1.2.0.51
Major
atmfM4VclXConnUp
.1.3.6.1.4.1.353.5.1.3.1.2.0.52
Normal
atmfM4VclXConnDown
.1.3.6.1.4.1.353.5.1.3.1.2.0.53
Major
atmfM4HwUnitUp
.1.3.6.1.4.1.353.5.1.3.1.2.0.54
Normal
atmfM4HwUnitDown
.1.3.6.1.4.1.353.5.1.3.1.2.0.55
Major
atmfM4AtmCellIfCreated
.1.3.6.1.4.1.353.5.1.3.1.2.0.56
Normal
atmfM4AtmCellIfDeleted
.1.3.6.1.4.1.353.5.1.3.1.2.0.57
Normal
atmfM4VpcTpCreated
.1.3.6.1.4.1.353.5.1.3.1.2.0.58
Normal
atmfM4VpcTpDeleted
.1.3.6.1.4.1.353.5.1.3.1.2.0.59
Normal
atmfM4VccTpCreated
.1.3.6.1.4.1.353.5.1.3.1.2.0.60
Normal
atmfM4VccTpDeleted
.1.3.6.1.4.1.353.5.1.3.1.2.0.61
Normal
atmfM4VplXConnCreated
.1.3.6.1.4.1.353.5.1.3.1.2.0.62
Normal
atmfM4VplXConnDeleted
.1.3.6.1.4.1.353.5.1.3.1.2.0.63
Normal
atmfM4VclXConnCreated
.1.3.6.1.4.1.353.5.1.3.1.2.0.64
Normal
atmfM4VclXConnDeleted
.1.3.6.1.4.1.353.5.1.3.1.2.0.65
Normal
atmfM4HwUnitCreated
.1.3.6.1.4.1.353.5.1.3.1.2.0.66
Normal
atmfM4HwUnitDeleted
.1.3.6.1.4.1.353.5.1.3.1.2.0.67
Normal
atmfM4InstalledSwCreated
.1.3.6.1.4.1.353.5.1.3.1.2.0.68
Normal
atmfM4InstalledSwDeleted
.1.3.6.1.4.1.353.5.1.3.1.2.0.69
Normal
atmfM4IfChanged
.1.3.6.1.4.1.353.5.1.3.1.2.0.70
Normal
atmfM4VplTpChanged
.1.3.6.1.4.1.353.5.1.3.1.2.0.71
Normal
atmfM4VclTpChanged
.1.3.6.1.4.1.353.5.1.3.1.2.0.72
Normal
atmfM4VplXConnChanged
.1.3.6.1.4.1.353.5.1.3.1.2.0.73
Normal
atmfM4VclXConnChanged
.1.3.6.1.4.1.353.5.1.3.1.2.0.74
Normal
atmfM4HwUnitChanged
.1.3.6.1.4.1.353.5.1.3.1.2.0.75
Normal
atmfM4InstalledSwChanged
.1.3.6.1.4.1.353.5.1.3.1.2.0.76
Normal
.1.3.6.1.2.1.37.1.14.2.1.0.1
Critical
draft-ietf-atommib-atm2-15.mi2 atmIntfPvcFailuresTrap
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-8 E-series standard traps (continued)
MIB Name
Trap Name
OID
Severity
draft-ietf-atommib-sonetaps-mi
b-05-juni.mi2
junidApsEventSwitchover
.1.3.6.1.4.1.4874.3.2.2.1.2.0.1
Normal
junidApsEventModeMismatch
.1.3.6.1.4.1.4874.3.2.2.1.2.0.2
Warning
junidApsEventChannelMismatch
.1.3.6.1.4.1.4874.3.2.2.1.2.0.3
Warning
junidApsEventPSBF
.1.3.6.1.4.1.4874.3.2.2.1.2.0.4
Warning
junidApsEventFEPLF
.1.3.6.1.4.1.4874.3.2.2.1.2.0.5
Warning
.1.3.6.1.2.1.88.2.0.1
Normal
mteTriggerRising
.1.3.6.1.2.1.88.2.0.2
Normal
mteTriggerFalling
.1.3.6.1.2.1.88.2.0.3
Normal
mteTriggerFailure
.1.3.6.1.2.1.88.2.0.4
Normal
mteEventSetFailure
.1.3.6.1.2.1.88.2.0.5
Normal
junidDvmrpNeighborLoss
.1.3.6.1.4.1.4874.3.2.1.1.1.1.0.1 Normal
junidDvmrpNeighborNotPruning
.1.3.6.1.4.1.4874.3.2.1.1.1.1.0.2 Normal
bgpEstablishedNotification
.1.3.6.1.2.1.15.0.1
Normal
bgpBackwardTransNotification
.1.3.6.1.2.1.15.0.2
Minor
bgpEstablished
.1.3.6.1.2.1.15.7.0.1
Normal
bgpBackwardTransition
.1.3.6.1.2.1.15.7.0.2
Minor
newRoot
.1.3.6.1.2.1.17.0.1
Normal
topologyChange
.1.3.6.1.2.1.17.0.2
Normal
ospfVirtIfStateChange
.1.3.6.1.2.1.14.16.2.0.1
Critical
ospfNbrStateChange
.1.3.6.1.2.1.14.16.2.0.2
Minor
ospfVirtNbrStateChange
.1.3.6.1.2.1.14.16.2.0.3
Minor
ospfIfConfigError
.1.3.6.1.2.1.14.16.2.0.4
Critical
ospfVirtIfConfigError
.1.3.6.1.2.1.14.16.2.0.5
Critical
ospfIfAuthFailure
.1.3.6.1.2.1.14.16.2.0.6
Critical
ospfVirtIfAuthFailure
.1.3.6.1.2.1.14.16.2.0.7
Critical
ospfIfRxBadPacket
.1.3.6.1.2.1.14.16.2.0.8
Minor
ospfVirtIfRxBadPacket
.1.3.6.1.2.1.14.16.2.0.9
Minor
ospfTxRetransmit
.1.3.6.1.2.1.14.16.2.0.10
Warning
ospfVirtIfTxRetransmit
.1.3.6.1.2.1.14.16.2.0.11
Warning
ospfOriginateLsa
.1.3.6.1.2.1.14.16.2.0.12
Normal
ospfMaxAgeLsa
.1.3.6.1.2.1.14.16.2.0.13
Warning
ospfLsdbOverflow
.1.3.6.1.2.1.14.16.2.0.14
Critical
draft-ietf-disman-event-mib-v2- mteTriggerFired
01.mi2
draft-ietf-idmr-dvmrp-mib-11-ju
ni.mi2
draft-ietf-idr-bgp4-mib-07.mi2
rfc1493.mib
rfc1850t.mi2
A-9
A-10
APPENDIX A
MIBs and Traps
Table A-8 E-series standard traps (continued)
MIB Name
Trap Name
OID
Severity
ospfLsdbApproachingOverflow
.1.3.6.1.2.1.14.16.2.0.15
Major
ospfIfStateChange
.1.3.6.1.2.1.14.16.2.0.16
Normal
rfc2115.mi2
frDLCIStatusChange
.1.3.6.1.2.1.10.32.0.1
Normal
rfc2513.mi2
acctngFileNearlyFull
.1.3.6.1.2.1.60.2.0.1
Minor
acctngFileFull
.1.3.6.1.2.1.60.2.0.2
Critical
rfc2737.mi2
entConfigChange
.1.3.6.1.2.1.47.2.0.1
Critical
rfc2787.mi2
vrrpTrapNewMaster
.1.3.6.1.2.1.68.0.1
Normal
vrrpTrapAuthFailure
.1.3.6.1.2.1.68.0.2
Warning
SNMP_Link_Down
.1.3.6.1.6.3.1.1.5.3
Minor
SNMP_Link_Up
.1.3.6.1.6.3.1.1.5.4
Normal
pingProbeFailed
.1.3.6.1.2.1.80.0.1
Minor
pingTestFailed
.1.3.6.1.2.1.80.0.2
Critical
pingTestCompleted
.1.3.6.1.2.1.80.0.3
Normal
traceRoutePathChange
.1.3.6.1.2.1.81.0.1
Warning
traceRouteTestFailed
.1.3.6.1.2.1.81.0.2
Critical
traceRouteTestCompleted
.1.3.6.1.2.1.81.0.3
Normal
rfc2934.mi2
pimNeighborLoss
.1.3.6.1.3.61.1.0.1
Normal
rfc3418.mi2
SNMP_Cold_Start
.1.3.6.1.6.3.1.1.5.1
Normal
SNMP_Authen_Failure
.1.3.6.1.6.3.1.1.5.5
Warning
SNMP_Authen_Failure
.1.3.6.1.6.3.1.1.5.5
Warning
rfc2863.mi2
rfc2925p.mi2
rfc2925t.mi2
E-Series Juniper Networks Traps
E-series Juniper Networks traps are defined in the MIB files listed in
Table A-9. Unless otherwise noted, the alarm type for these traps is
“Juniper Alarms” and the severity level is “Normal.”
Table A-9 E-series Juniper Networks traps
MIB Name
Trap Name
OID
JuniSystem.mi2
juniSystemHighMemUtil
.1.3.6.1.4.1.4874.2.2.2.0.1
Note: Severity is Warning
juniSystemAbatedMemUtil
.1.3.6.1.4.1.4874.2.2.2.0.2
Note: Severity is Warning
juniSystemModuleOperStatusChange
.1.3.6.1.4.1.4874.2.2.2.0.3
juniSystemPowerStatusChange
.1.3.6.1.4.1.4874.2.2.2.0.4
juniSystemFanStatusChange
.1.3.6.1.4.1.4874.2.2.2.0.5
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-9 E-series Juniper Networks traps (continued)
MIB Name
Trap Name
OID
juniSystemTempStatusChange
.1.3.6.1.4.1.4874.2.2.2.0.6
juniSystemTempProtectionStatusChange
.1.3.6.1.4.1.4874.2.2.2.0.7
juniSystemReloadCommand
.1.3.6.1.4.1.4874.2.2.2.0.8
juniSystemUtilizationThreshold
.1.3.6.1.4.1.4874.2.2.2.0.9
juniSonet.mi2
juniSonetPathEvents
.1.3.6.1.4.1.4874.2.2.7.6.0.1
juniAtm.mi2
juniAtmVpPingTestCompleted
.1.3.6.1.4.1.4874.2.2.8.3.0.1
juniAtmVcPingTestCompleted
.1.3.6.1.4.1.4874.2.2.8.3.0.2
juniERXSysSlotOperStatusChange
.1.3.6.1.4.1.4874.2.2.17.0.1
juniERXSysPowerStatusChange
.1.3.6.1.4.1.4874.2.2.17.0.2
juniERXSysTempFanStatusChange
.1.3.6.1.4.1.4874.2.2.17.0.3
juniERXSysTempStatusChange
.1.3.6.1.4.1.4874.2.2.17.0.4
juniErxSystem.mi2
Note: Alarm type is LOGONLY
juniRadClient.mi2
juniERXSysHighMemUtil
.1.3.6.1.4.1.4874.2.2.17.0.5
juniERXSysAbatedMemUtil
.1.3.6.1.4.1.4874.2.2.17.0.6
juniERXSysTempProtectionStatusChange
.1.3.6.1.4.1.4874.2.2.17.0.7
juniRadiusAuthClientServerUnavailable
.1.3.6.1.4.1.4874.2.2.19.3.0.1
juniRadiusAuthClientNoServerAvailable
.1.3.6.1.4.1.4874.2.2.19.3.0.2
Note: Alarm type is LOGONLY
juniRadiusAcctClientServerUnavailable
.1.3.6.1.4.1.4874.2.2.19.3.0.3
juniRadiusAcctClientNoServerAvailable
.1.3.6.1.4.1.4874.2.2.19.3.0.4
juniRadiusAuthClientServerAvailable
.1.3.6.1.4.1.4874.2.2.19.3.0.5
juniRadiusAcctClientServerAvailable
.1.3.6.1.4.1.4874.2.2.19.3.0.6
juniAddressPoolHighAddrUtil
.1.3.6.1.4.1.4874.2.2.21.3.0.1
juniAddressPoolAbatedAddrUtil
.1.3.6.1.4.1.4874.2.2.21.3.0.2
juniAddressPoolNoAddresses
.1.3.6.1.4.1.4874.2.2.21.3.0.3
juniFileXfer.mi2
juniFileXferTrap
.1.3.6.1.4.1.4874.2.2.23.2.0.1
juniLog.mi2
juniLogMsgThresholdTrap
.1.3.6.1.4.1.4874.2.2.28.0.1
juniCli.mi2
juniCliSecurityAlert
.1.3.6.1.4.1.4874.2.2.30.0.1
juniDvmrp.mi2
juniDvmrpRouteHogNotificationTrap
.1.3.6.1.4.1.4874.2.2.44.1.1.0.1
juniSystemClock.mi2
juniNtpFrequencyCalibrationStart
.1.3.6.1.4.1.4874.2.2.56.2.0.1
juniNtpFrequencyCalibrationEnd
.1.3.6.1.4.1.4874.2.2.56.2.0.2
juniNtpTimeSynUp
.1.3.6.1.4.1.4874.2.2.56.2.0.3
juniNtpTimeSynDown
.1.3.6.1.4.1.4874.2.2.56.2.0.4
juniNtpTimeServerSynUp
.1.3.6.1.4.1.4874.2.2.56.2.0.5
juniNtpTimeServerSynDown
.1.3.6.1.4.1.4874.2.2.56.2.0.6
juniAddrPool.mi2
A-11
A-12
APPENDIX A
MIBs and Traps
Table A-9 E-series Juniper Networks traps (continued)
MIB Name
Trap Name
OID
juniNtpFirstSystemClockSet
.1.3.6.1.4.1.4874.2.2.56.2.0.7
juniNtpClockOffSetLimitCrossed
.1.3.6.1.4.1.4874.2.2.56.2.0.8
M-Series and T-Series Traps
See the following sections for a list of M-series and T-series standard traps
and Juniper Networks traps.
M-Series and T-Series Standard Traps
M-series and T-series platform standard traps are defined in the MIB
files listed in Table A-10. Unless otherwise noted, the alarm type for these
traps is “Juniper Alarms” and the severity level is “Normal.”
Table A-10 M-series and T-series standard traps
MIB Name
Trap Name
OID
ggsn.mib
ggsnTrapNew
.1.3.6.1.4.1.10923.1.1.2.1
ggsnTrapChanged
.1.3.6.1.4.1.10923.1.1.2.2
ggsnTrapCleared
.1.3.6.1.4.1.10923.1.1.2.3
rfc2495a.mib
dsx1LineStatusChange
.1.3.6.1.2.1.10.18.15.0.1
rfc2496a.mib
dsx3LineStatusChange
.1.3.6.1.2.1.10.30.15.0.1
frc3020.mib
mfrMibTrapBundleLinkMismatch
.1.3.6.1.2.1.10.47.4.0.1
ldpmib.mib
mplsLdpInitSesThresholdExceeded
.1.3.6.1.2.1.10.166.3.2.0.1
mplsLdpPathVectorLimitMismatch
.1.3.6.1.2.1.10.166.3.2.0.2
mplsLdpSessionUp
.1.3.6.1.2.1.10.166.3.2.0.3
mplsLdpSessionDown
.1.3.6.1.2.1.10.166.3.2.0.4
rfc2465.mib
ipv6IfStateChange
.1.3.6.1.2.1.55.2.0.1
isismib.mib
isisDatabaseOverload
.1.3.6.1.3.37.2.0.1
isisManualAddressDrops
.1.3.6.1.3.37.2.0.2
isisCorruptedLSPDetected
.1.3.6.1.3.37.2.0.3
isisAttemptToExceedMaxSequence
.1.3.6.1.3.37.2.0.4
isisIDLenMismatch
.1.3.6.1.3.37.2.0.5
isisMaxAreaAddressesMismatch
.1.3.6.1.3.37.2.0.6
isisOwnLSPPurge
.1.3.6.1.3.37.2.0.7
isisSequenceNumberSkip
.1.3.6.1.3.37.2.0.8
isisAuthenticationTypeFailure
.1.3.6.1.3.37.2.0.9
isisAuthenticationFailure
.1.3.6.1.3.37.2.0.10
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-10 M-series and T-series standard traps (continued)
MIB Name
l3vpnmib.mib
Trap Name
OID
isisVersionSkew
.1.3.6.1.3.37.2.0.11
isisAreaMismatch
.1.3.6.1.3.37.2.0.12
isisRejectedAdjacency
.1.3.6.1.3.37.2.0.13
isisLSPTooLargeToPropagate
.1.3.6.1.3.37.2.0.14
isisOriginatingLSPBufferSizeMismatch
.1.3.6.1.3.37.2.0.15
isisProtocolsSupportedMismatch
.1.3.6.1.3.37.2.0.16
mplsVrfIfUp 1
.1.3.6.1.3.118.0.
mplsVrfIfDown
.1.3.6.1.3.118.0.2
mplsNumVrfRouteMidThreshExceeded
.1.3.6.1.3.118.0.3
mplsNumVrfRouteMaxThreshExceeded .1.3.6.1.3.118.0.4
rfc2819a.mib
mplsNumVrfSecIllglLblThrshExcd
.1.3.6.1.3.118.0.5
RMON_Rise_Alarm
.1.3.6.1.2.1.16.0.1
Note: Alarm type is Threshold Alarms
and severity is Warning
RMON_Falling_Alarm
.1.3.6.1.2.1.16.0.2
Note: Alarm type is Threshold Alarms
and severity is Warning
M-Series and T-Series Juniper Networks Traps
M-series and T-series platform Juniper Networks traps are defined in the
MIB files listed in Table A-11. Unless otherwise noted, the alarm type for
these traps is “Juniper Alarms” and the severity level is “Normal.”
Table A-11 M-series and T-series Juniper Networks traps
MIB Name
Trap Name
OID
mib-jnx-mpls.txt
mplsLspUp
.1.3.6.1.4.1.2636.3.2.4.1
mplsLspDown
.1.3.6.1.4.1.2636.3.2.4.2
mplsLspChange
.1.3.6.1.4.1.2636.3.2.4.3
apsEventSwitchover
.1.3.6.1.4.1.2636.3.24.2.0.1
apsEventModeMismatch
.1.3.6.1.4.1.2636.3.24.2.0.2
apsEventChannelMismatch
.1.3.6.1.4.1.2636.3.24.2.0.3
apsEventPSBF
.1.3.6.1.4.1.2636.3.24.2.0.4
apsEventFEPLF
.1.3.6.1.4.1.2636.3.24.2.0.5
jnxVpnIfUp
.1.3.6.1.4.1.2636.3.26.0.1
jnxVpnIfDown
.1.3.6.1.4.1.2636.3.26.0.2
jnxVpnPwUp
.1.3.6.1.4.1.2636.3.26.0.3
mib-jnx-sonetaps.txt
mib-jnx-vpn.txt
A-13
A-14
APPENDIX A
MIBs and Traps
Table A-11 M-series and T-series Juniper Networks traps (continued)
MIB Name
Trap Name
OID
jnxVpnPwDown
.1.3.6.1.4.1.2636.3.26.0.4
jnxPowerSupplyFailure
.1.3.6.1.4.1.2636.4.1.1
jnxFanFailure
.1.3.6.1.4.1.2636.4.1.2
jnxOverTemperature
.1.3.6.1.4.1.2636.4.1.3
jnxRedundancySwitchover
.1.3.6.1.4.1.2636.4.1.4
jnxFruRemoval
.1.3.6.1.4.1.2636.4.1.5
jnxFruInsertion
.1.3.6.1.4.1.2636.4.1.6
jnxFruPowerOff
.1.3.6.1.4.1.2636.4.1.7
jnxFruPowerOn
.1.3.6.1.4.1.2636.4.1.8
jnxPowerSupplyOK
.1.3.6.1.4.1.2636.4.2.1
jnxFanOK
.1.3.6.1.4.1.2636.4.2.2
jnxTemperatureOK
.1.3.6.1.4.1.2636.4.2.3
jnxRmonAlarmGetFailure
.1.3.6.1.4.1.2636.4.3.0.1
jnxRmonGetOk
.1.3.6.1.4.1.2636.4.3.0.2
jnxLdpLspUp
.1.3.6.1.4.1.2636.4.4.0.1
jnxLdpLspDown
.1.3.6.1.4.1.2636.4.4.0.2
jnxLdpSesUp
.1.3.6.1.4.1.2636.4.4.0.3
jnxLdpSesDown
.1.3.6.1.4.1.2636.4.4.0.4
mib-jnx-cfgmgmt.txt
jnxCmCfgChange
.1.3.6.1.4.1.2636.4.5.0.1
mib-jnx-sonet.txt
jnxSonetAlarmSet
.1.3.6.1.4.1.2636.4.6.0.1
jnxSonetAlarmCleared
.1.3.6.1.4.1.2636.4.6.0.2
jnxPMonOverloadSet
.1.3.6.1.4.1.2636.4.7.0.1
jnxPMonOverloadCleared
.1.3.6.1.4.1.2636.4.7.0.2
jnxBgpM2Established
.1.3.6.1.4.1.2636.5.1.1.1.0.1
jnxBgpM2BackwardTransition
.1.3.6.1.4.1.2636.5.1.1.1.0.2
mib-jnx-chassis.txt
mib-jnx-rmon.txt
mib-jnx-ldp.txt
mib-jnx-pmon.txt
mib-jnx-bgpmib2.txt
SDX Software Traps
See the following section for a list of SDX software Juniper Networks
traps.
SDX Software Juniper Networks Traps
SDX software traps are defined in the MIB file jnxSdxRtrap.mi2. Unless
otherwise noted, the alarm type for these traps is “SDX Alarms” and the
severity level is “Normal.”
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-12 SDX software (version 1) Juniper Networks traps
Trap Name
OID
saeHeapUsedClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.10
saeHeapUsedCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.11
saeHeapUsedMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.12
saeHeapUsedMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.13
saeLoginsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.20
saeLoginsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.21
saeLoginsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.22
saeLoginsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.23
saeLogoutsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.30
saeLogoutsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.31
saeLogoutsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.32
saeLogoutsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.33
saeServiceActClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.40
saeServiceActCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.41
saeServiceActMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.42
saeServiceActMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.43
saeServiceDeactClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.50
saeServiceDeactCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.51
saeServiceDeactMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.52
saeServiceDeactMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.53
saeCurrentUsersClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.60
saeCurrentUsersCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.61
saeCurrentUsersMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.62
saeCurrentUsersMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.63
saeUserNumLicClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.70
saeUserNumLicCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.71
saeUserNumLicMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.72
saeUserNumLicMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.73
saeUserLicExpiryClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.80
saeUserLicExpiryCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.81
saeUserLicExpiryMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.82
saeUserLicExpiryMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.83
licenseNetworkCapacityTrap
.1.3.6.1.4.1.4874.6.1.10.0.90
serviceLicenseClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.100
A-15
A-16
APPENDIX A
MIBs and Traps
Table A-12 SDX software (version 1) Juniper Networks traps (continued)
Trap Name
OID
serviceLicenseCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.101
serviceLicenseMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.102
serviceLicenseMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.103
serviceSessionLicenseClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.110
serviceSessionLicenseCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.111
serviceSessionLicenseMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.112
serviceSessionLicenseMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.113
saeAccInvSvrAddrClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.200
saeAccInvSvrAddrCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.201
saeAccInvSvrAddrMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.202
saeAccInvSvrAddrMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.203
saeAccRoundTripTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.210
saeAccRoundTripTimeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.211
saeAccRoundTripTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.212
saeAccRoundTripTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.213
saeAccRetransClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.220
saeAccRetransCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.221
saeAccRetransMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.222
saeAccRetransMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.223
saeAccMalformedRespClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.230
saeAccMalformedRespCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.231
saeAccMalformedRespMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.232
saeAccMalformedRespMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.233
saeAccBadAuthentClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.240
saeAccBadAuthentCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.241
saeAccBadAuthentMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.242
saeAccBadAuthentMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.243
saeAccPendingsReqsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.250
saeAccPendingsReqsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.251
saeAccPendingsReqsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.252
saeAccPendingsReqsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.253
saeAccTimeoutsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.260
saeAccTimeoutsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.261
saeAccTimeoutsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.262
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-12 SDX software (version 1) Juniper Networks traps (continued)
Trap Name
OID
saeAccTimeoutsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.263
saeAccUnknownTypesClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.270
saeAccUnknownTypesCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.271
saeAccUnknownTypesMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.272
saeAccUnknownTypesMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.273
saeAccPcktsDroppedClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.280
saeAccPcktsDroppedCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.281
saeAccPcktsDroppedMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.282
saeAccPcktsDroppedMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.283
saeAuthInvSvrAddrClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.400
saeAuthInvSvrAddrCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.401
saeAuthInvSvrAddrMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.402
saeAuthInvSvrAddrMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.403
saeAuthRoundTripTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.410
saeAuthRoundTripTimeCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.411
saeAuthRoundTripTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.412
saeAuthRoundTripTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.413
saeAuthRetransClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.420
saeAuthRetransCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.421
saeAuthRetransMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.422
saeAuthRetransMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.423
saeAuthMalformedRespClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.430
saeAuthMalformedRespCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.431
saeAuthMalformedRespMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.432
saeAuthMalformedRespMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.433
saeAuthBadAuthentClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.440
saeAuthBadAuthentCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.441
saeAuthBadAuthentMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.442
saeAuthBadAuthentMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.443
saeAuthPendingReqsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.450
saeAuthPendingReqsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.451
saeAuthPendingReqsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.452
saeAuthPendingReqsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.453
saeAuthTimeoutsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.460
A-17
A-18
APPENDIX A
MIBs and Traps
Table A-12 SDX software (version 1) Juniper Networks traps (continued)
Trap Name
OID
saeAuthTimeoutsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.461
saeAuthTimeoutsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.462
saeAuthTimeoutsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.463
saeAuthUnknownTypesClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.470
saeAuthUnknownTypesCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.471
saeAuthUnknownTypesMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.472
saeAuthUnknownTypesMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.473
saeAuthPcktsDroppedClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.480
saeAuthPcktsDroppedCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.481
saeAuthPcktsDroppedMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.482
saeAuthPcktsDroppedMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.483
copsManagedIntfClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.600
copsManagedIntfCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.601
copsManagedIntfMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.602
copsManagedIntfMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.603
copsUserSessionEstabClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.610
copsUserSessionEstabCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.611
copsUserSessionEstabMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.612
copsUserSessionEstabMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.613
copsUserSessionRmvdClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.620
copsUserSessionRmvdCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.621
copsUserSessionRmvdMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.622
copsUserSessionRmvdMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.623
copsErrorsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.630
copsErrorsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.631
copsErrorsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.632
copsErrorsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.633
copsTimeoutsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.640
copsTimeoutsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.641
copsTimeoutsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.642
copsTimeoutsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.643
copsAvgREQHandleTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.650
copsAvgREQHandleTimeCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.651
copsAvgREQHandleTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.652
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-12 SDX software (version 1) Juniper Networks traps (continued)
Trap Name
OID
copsAvgREQHandleTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.653
copsJobQueueLengthClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.660
copsJobQueueLengthCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.661
copsJobQueueLengthMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.662
copsJobQueueLengthMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.663
copsAvgQueueTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.670
copsAvgQueueTimeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.671
copsAvgQueueTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.672
copsAvgQueueTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.673
copsAgeOldQueueMemberClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.680
copsAgeOldQueueMemberCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.681
copsAgeOldQueueMemberMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.682
copsAgeOldQueueMemberMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.683
copsClientsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.690
copsClientsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.691
copsClientsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.692
copsClientsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.693
copsIgnoredRequestsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.700
copsIgnoredRequestsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.701
copsIgnoredRequestsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.702
copsIgnoredRequestsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.703
copsConnectionClosed
.1.3.6.1.4.1.4874.6.1.10.0.715
copsConnectionUp
.1.3.6.1.4.1.4874.6.1.10.0.725
copsConnectionDown
.1.3.6.1.4.1.4874.6.1.10.0.735
copsConnectionRejected
.1.3.6.1.4.1.4874.6.1.10.0.745
copsOverload
.1.3.6.1.4.1.4874.6.1.10.0.751
wkfInstanceSizeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.900
wkfInstanceSizeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.901
wkfInstanceSizeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.902
wkfInstanceSizeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.903
wkfEventSizeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.910
wkfEventSizeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.911
wkfEventSizeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.912
wkfEventSizeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.913
A-19
A-20
APPENDIX A
MIBs and Traps
Table A-12 SDX software (version 1) Juniper Networks traps (continued)
Trap Name
OID
wkfReportSizeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.920
wkfReportSizeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.921
wkfReportSizeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.922
wkfReportSizeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.923
wkfPersistentSizeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.930
wkfPersistentSizeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.931
wkfPersistentSizeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.932
wkfPersistentSizeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.933
wkfCancelledClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.940
wkfCancelledCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.941
wkfCancelledMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.942
wkfCancelledMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.943
wkfPendingEventsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.950
wkfPendingEventsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.951
wkfPendingEventsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.952
wkfPendingEventsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.953
wkfActiveClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.960
wkfActiveCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.961
wkfActiveMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.962
wkfActiveMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.963
wkfRunningClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.970
wkfRunningCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.971
wkfRunningMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.972
wkfRunningMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.973
agentStarted
.1.3.6.1.4.1.4874.6.1.10.0.1105
agentRestartFailed
.1.3.6.1.4.1.4874.6.1.10.0.1111
agentShutdown
.1.3.6.1.4.1.4874.6.1.10.0.1125
agentLdapLimitClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1130
agentLdapLimitCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1131
agentLdapLimitMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1132
agentLdapLimitMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1133
componentUp
.1.3.6.1.4.1.4874.6.1.10.0.1145
componentDown
.1.3.6.1.4.1.4874.6.1.10.0.1155
dirConnected
.1.3.6.1.4.1.4874.6.1.10.0.1305
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-12 SDX software (version 1) Juniper Networks traps (continued)
Trap Name
OID
dirConnectionFailure
.1.3.6.1.4.1.4874.6.1.10.0.1311
dirNotAvail
.1.3.6.1.4.1.4874.6.1.10.0.1321
penAvgPGModProcTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1500
penAvgPGModProcTimeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1501
penAvgPGModProcTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1502
penAvgPGModProcTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1503
penAvgICMModProcTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1510
penAvgICMModProcTimeCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1511
penAvgICMModProcTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1512
penAvgICMModProcTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1513
pdpErrorsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1520
pdpErrorsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1521
pdpErrorsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1522
pdpErrorsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1523
Table A-13 SDX software (version 2) Juniper Networks traps
Trap Name
OID
saeHeapUsedClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.10.10
saeHeapUsedCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.11.11
saeHeapUsedMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.12.12
saeHeapUsedMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.13.13
saeLoginsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.20.20
saeLoginsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.21.21
saeLoginsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.22.22
saeLoginsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.23.23
saeLogoutsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.30.30
saeLogoutsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.31.31
saeLogoutsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.32.32
saeLogoutsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.33.33
saeServiceActClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.40.40
saeServiceActCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.41.41
saeServiceActMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.42.42
saeServiceActMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.43.43
A-21
A-22
APPENDIX A
MIBs and Traps
Table A-13 SDX software (version 2) Juniper Networks traps (continued)
Trap Name
OID
saeServiceDeactClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.50.50
saeServiceDeactCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.51.51
saeServiceDeactMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.52.52
saeServiceDeactMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.53.53
saeCurrentUsersClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.60.60
saeCurrentUsersCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.61.61
saeCurrentUsersMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.62.62
saeCurrentUsersMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.63.63
saeUserNumLicClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.70.70
saeUserNumLicCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.71.71
saeUserNumLicMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.72.72
saeUserNumLicMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.73.73
saeUserLicExpiryClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.80.80
saeUserLicExpiryCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.81.81
saeUserLicExpiryMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.82.82
saeUserLicExpiryMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.83.83
licenseNetworkCapacityTrap
.1.3.6.1.4.1.4874.6.1.10.0.90.90
serviceLicenseClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.100.100
serviceLicenseCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.101.101
serviceLicenseMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.102.102
serviceLicenseMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.103.103
serviceSessionLicenseClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.110.110
serviceSessionLicenseCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.111.111
serviceSessionLicenseMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.112.112
serviceSessionLicenseMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.113.113
saeAccInvSvrAddrClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.200.200
saeAccInvSvrAddrCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.201.201
saeAccInvSvrAddrMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.202.202
saeAccInvSvrAddrMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.203.203
saeAccRoundTripTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.210.210
saeAccRoundTripTimeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.211.211
saeAccRoundTripTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.212.212
saeAccRoundTripTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.213.213
saeAccRetransClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.220.220
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-13 SDX software (version 2) Juniper Networks traps (continued)
Trap Name
OID
saeAccRetransCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.221.221
saeAccRetransMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.222.222
saeAccRetransMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.223.223
saeAccMalformedRespClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.230.230
saeAccMalformedRespCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.231.231
saeAccMalformedRespMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.232.232
saeAccMalformedRespMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.233.233
saeAccBadAuthentClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.240.240
saeAccBadAuthentCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.241.241
saeAccBadAuthentMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.242.242
saeAccBadAuthentMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.243.243
saeAccPendingsReqsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.250.250
saeAccPendingsReqsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.251.251
saeAccPendingsReqsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.252.252
saeAccPendingsReqsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.253.253
saeAccTimeoutsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.260.260
saeAccTimeoutsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.261.261
saeAccTimeoutsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.262.262
saeAccTimeoutsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.263.263
saeAccUnknownTypesClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.270.270
saeAccUnknownTypesCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.271.271
saeAccUnknownTypesMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.272.272
saeAccUnknownTypesMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.273.273
saeAccPcktsDroppedClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.280.280
saeAccPcktsDroppedCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.281.281
saeAccPcktsDroppedMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.282.282
saeAccPcktsDroppedMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.283.283
saeAuthInvSvrAddrClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.400.400
saeAuthInvSvrAddrCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.401.401
saeAuthInvSvrAddrMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.402.402
saeAuthInvSvrAddrMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.403.403
saeAuthRoundTripTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.410.410
saeAuthRoundTripTimeCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.411.411
saeAuthRoundTripTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.412.412
A-23
A-24
APPENDIX A
MIBs and Traps
Table A-13 SDX software (version 2) Juniper Networks traps (continued)
Trap Name
OID
saeAuthRoundTripTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.413.413
saeAuthRetransClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.420.420
saeAuthRetransCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.421.421
saeAuthRetransMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.422.422
saeAuthRetransMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.423.423
saeAuthMalformedRespClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.430.430
saeAuthMalformedRespCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.431.431
saeAuthMalformedRespMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.432.432
saeAuthMalformedRespMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.433.433
saeAuthBadAuthentClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.440.440
saeAuthBadAuthentCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.441.441
saeAuthBadAuthentMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.442.442
saeAuthBadAuthentMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.443.443
saeAuthPendingReqsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.450.450
saeAuthPendingReqsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.451.451
saeAuthPendingReqsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.452.452
saeAuthPendingReqsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.453.453
saeAuthTimeoutsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.460.460
saeAuthTimeoutsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.461.461
saeAuthTimeoutsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.462.462
saeAuthTimeoutsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.463.463
saeAuthUnknownTypesClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.470.470
saeAuthUnknownTypesCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.471.471
saeAuthUnknownTypesMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.472.472
saeAuthUnknownTypesMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.473.473
saeAuthPcktsDroppedClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.480.480
saeAuthPcktsDroppedCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.481.481
saeAuthPcktsDroppedMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.482.482
saeAuthPcktsDroppedMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.483.483
copsManagedIntfClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.600.600
copsManagedIntfCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.601.601
copsManagedIntfMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.602.602
copsManagedIntfMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.603.603
copsUserSessionEstabClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.610.610
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-13 SDX software (version 2) Juniper Networks traps (continued)
Trap Name
OID
copsUserSessionEstabCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.611.611
copsUserSessionEstabMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.612.612
copsUserSessionEstabMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.613.613
copsUserSessionRmvdClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.620.620
copsUserSessionRmvdCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.621.621
copsUserSessionRmvdMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.622.622
copsUserSessionRmvdMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.623.623
copsErrorsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.630.630
copsErrorsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.631.631
copsErrorsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.632.632
copsErrorsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.633.633
copsTimeoutsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.640.640
copsTimeoutsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.641.641
copsTimeoutsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.642.642
copsTimeoutsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.643.643
copsAvgREQHandleTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.650.650
copsAvgREQHandleTimeCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.651.651
copsAvgREQHandleTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.652.652
copsAvgREQHandleTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.653.653
copsJobQueueLengthClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.660.660
copsJobQueueLengthCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.661.661
copsJobQueueLengthMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.662.662
copsJobQueueLengthMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.663.663
copsAvgQueueTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.670.670
copsAvgQueueTimeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.671.671
copsAvgQueueTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.672.672
copsAvgQueueTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.673.673
copsAgeOldQueueMemberClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.680.680
copsAgeOldQueueMemberCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.681.681
copsAgeOldQueueMemberMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.682.682
copsAgeOldQueueMemberMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.683.683
copsClientsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.690.690
copsClientsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.691.691
copsClientsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.692.692
A-25
A-26
APPENDIX A
MIBs and Traps
Table A-13 SDX software (version 2) Juniper Networks traps (continued)
Trap Name
OID
copsClientsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.693.693
copsIgnoredRequestsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.700.700
copsIgnoredRequestsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.701.701
copsIgnoredRequestsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.702.702
copsIgnoredRequestsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.703.703
copsConnectionClosed
.1.3.6.1.4.1.4874.6.1.10.0.715.715
copsConnectionUp
.1.3.6.1.4.1.4874.6.1.10.0.725.725
copsConnectionDown
.1.3.6.1.4.1.4874.6.1.10.0.735.735
copsConnectionRejected
.1.3.6.1.4.1.4874.6.1.10.0.745.745
copsOverload
.1.3.6.1.4.1.4874.6.1.10.0.751.751
wkfInstanceSizeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.900.900
wkfInstanceSizeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.901.901
wkfInstanceSizeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.902.902
wkfInstanceSizeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.903.903
wkfEventSizeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.910.910
wkfEventSizeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.911.911
wkfEventSizeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.912.912
wkfEventSizeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.913.913
wkfReportSizeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.920.920
wkfReportSizeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.921.921
wkfReportSizeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.922.922
wkfReportSizeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.923.923
wkfPersistentSizeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.930.930
wkfPersistentSizeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.931.931
wkfPersistentSizeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.932.932
wkfPersistentSizeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.933.933
wkfCancelledClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.940.940
wkfCancelledCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.941.941
wkfCancelledMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.942.942
wkfCancelledMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.943.943
wkfPendingEventsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.950.950
wkfPendingEventsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.951.951
wkfPendingEventsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.952.952
wkfPendingEventsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.953.953
SNMP Traps for Juniper Networks Devices
HP OpenView Integration Pack
Table A-13 SDX software (version 2) Juniper Networks traps (continued)
Trap Name
OID
wkfActiveClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.960.960
wkfActiveCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.961.961
wkfActiveMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.962.962
wkfActiveMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.963.963
wkfRunningClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.970.970
wkfRunningCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.971.971
wkfRunningMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.972.972
wkfRunningMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.973.973
agentStarted
.1.3.6.1.4.1.4874.6.1.10.0.1105.1105
agentRestartFailed
.1.3.6.1.4.1.4874.6.1.10.0.1111.1111
agentShutdown
.1.3.6.1.4.1.4874.6.1.10.0.1125.1125
agentLdapLimitClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1130.1130
agentLdapLimitCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1131.1131
agentLdapLimitMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1132.1132
agentLdapLimitMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1133.1133
componentUp
.1.3.6.1.4.1.4874.6.1.10.0.1145.1145
componentDown
.1.3.6.1.4.1.4874.6.1.10.0.1155.1155
dirConnected
.1.3.6.1.4.1.4874.6.1.10.0.1305.1305
dirConnectionFailure
.1.3.6.1.4.1.4874.6.1.10.0.1311.1311
dirNotAvail
.1.3.6.1.4.1.4874.6.1.10.0.1321.1321
penAvgPGModProcTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1500.1500
penAvgPGModProcTimeCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1501.1501
penAvgPGModProcTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1502.1502
penAvgPGModProcTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1503.1503
penAvgICMModProcTimeClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1510.1510
penAvgICMModProcTimeCritAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1511.1511
penAvgICMModProcTimeMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1512.1512
penAvgICMModProcTimeMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1513.1513
pdpErrorsClearAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1520.1520
pdpErrorsCriticalAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1521.1521
pdpErrorsMajorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1522.1522
pdpErrorsMinorAlarm
.1.3.6.1.4.1.4874.6.1.10.0.1523.1523
A-27
A-28
APPENDIX A
MIBs and Traps