Download USER｀MANUAL

DOT MATRIX
LIQUID CRYSTAL DISPLAY
MODULE
COMPANY NAME：_______________
USER｀MANUAL
LMG-S16D80 Serial
LCD Module Description: _______________
PROPOSED BY
Design
APPROVED
Approved
SDEC TECHNOLOGY CORP.
ADDRESS: 10F, No. 100, Shing De Rd., San Chung City 241
Taipei Hsien, Taiwan R.O.C.
TEL: 886-2-2999-2512/886-2-8512-1288
FAX: 886-2-2999-2510/886-2-8512-2828
EMAIL:[email protected]/[email protected]
http://www.sdec.com.tw
LMG-S16D80
LCM SAMPLE APPROVAL
(液
晶
顯
示
模
組
樣
品
確
認
書)
１． PART A:FILLED BY SDEC TECH（由 SDEC 填寫）
1) COMPANY NAME（客戶名稱）：＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
2) SDEC ITEM NO.（產品型號）：＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
3) CUSTOMER ITEM NO.（客戶產品型號）：＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
4) LCM Function (LCM 內容)：
LCD TYPE (LCD 種類)：□ TN, □ HTN, □ STN, □ FSTN ( □ POSITIVE/正向,
□ NEGATIVE/反向, □ BLACK MASK/內黑絲印)
B
VIEWING AREA (視角方向)：□ 3H, □ 6H, □ 9H, □ 12H
C
POLARIZER COLOR (偏光板顏色)：□ GRAY/灰色, □ YELLOW GREEN/黃綠色,
□ BLUE/藍色, □ BLACK/黑色
D
BACKLIGHT COLOR (背光顏色)：□ YELLOW GREEN/黃綠光, □ ORANGE/橘光
□ RED/紅光, □ BLUE/藍光, □ GREEN/翠綠光, □ WHITE/白光
E
TEMPERATURE (溫度)：□ NORMAL/常溫, ■ WIDE/廣溫
F
PCB RESISTOR (PCB 板電阻)：R1(
KΩ), R2/R3/R5/R6( 2KΩ), R4(
KΩ),
R7(
Ω), R11(
Ω) , R12( Ω), D1(
)
G
CONTROL IC (控制 IC)：LC7981
SAMPLE DELIVERY DATE（出樣日期）：＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿＿
A
２．PART B:FILLED BY CUSTOMER（請客戶填寫）
ＯＫ ＮＧ
CHECK LIST ITEMS（檢查項目）：
REASON（原因）
1).LCM SIZE AND THICKNESS:（LCM 尺寸及厚度）
：
□
□
＿＿＿＿＿＿＿＿
2).POLARIZER COLOR：（偏光板色澤）：
□
□
＿＿＿＿＿＿＿＿
3).ELECTRO CHARACTERISTIC：（電氣特性）：
□
□
＿＿＿＿＿＿＿＿
4).VIEWING AREA（視角範圍）：
□
□
＿＿＿＿＿＿＿＿
5).BACKLIGHT ILLIMINATION（背光亮度）：
□
□
＿＿＿＿＿＿＿＿
6).TEMPERATURE RANGE（溫度範圍）：
□
□
＿＿＿＿＿＿＿＿
APPROVED BY（批准）：
DATE OF APPROVAL（批准日期）：
＿＿＿＿＿＿＿＿＿＿＿＿＿_____
______________＿＿＿＿＿＿＿＿＿＿
Ver 2007.05
2/18
www.sdec.com.tw
LMG-S16D80
0.1 SDEC
LM C
[1]
—
[2]
LM G
[1]
LCD
—
[2]
0.2 SDEC
NO
MODULE
NUMBERING
SYSTEM
—
S
T
C
2
E
16
D
L
Y
Y
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
S
S
12
A
64
U
E
G
W
[3]
[4]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
LCD
[5]
MODULE
VARIATION
ITEM
—
[13]
LIST
DESCRIPTION
[1] LCD MODULE
LIQUID CRYSTAL DISPLAY MODULE
[2] LCM MODULE
D DIGITS MODEL C
[3] LCM OF FUNCTION B
[4] LCD MODEL
CHARACTER MODEL G
S
SMALL/NORMAL TYPE
T
TN LCD
H
HTN LCD
S
STN LCD
F
FSTN LCD
PACKAGE TYPE C
[6]
STANDARD
[A]
[7]
TYPE LCM
[8]
STANDARD [6]
OR CUSTOM
[7]
[B]
DESIGNED
TYPE LCM [8]
GRAPHIC MODEL
BIG SIZE TYPE
[5] IC PACKING
CHIP(OR COG)TYPE
T
TAB TYPE
CHARACTER MODEL：NUMBER GRAPHIC MODEL：WIDE SIDE OF
OF LINES
DOTS
FROM A TO Z
CHARACTER MODEL:NUMBER
OF CHARACTER
GRAPHIC MODEL:HIGH SIDE OF
DOTS
DIGITS MODEL：YEAR+MONTH+NUMBER
CHARACTER MODEL：CHARACTER+LINES+NUMBER
GRAPHIC MODEL：WIDE SIDE DOTS+HIGH SIDE DOTS+NUMBER
[9] VIEWING ANGLE R
3 O’CLOCK D
6 O’CLOCK
L
9 O’CLOCK U
12 O’CLOCK
R
WITHOUT BACKLIGHT E
EL (TRANSFLECTIVE)
L
ARRAY LED
(TRANSFLECTIVE)
F
FL (TRANSMISSIVE)
G
GRAY
Y
YELLOW GREEN
[10] BACKLIGHT
POLARIZER
[11]
COLOR
[13]
N
NEGATIVE STN
TYPE : BLUE
NEGATIVE FSTN TYPE : BLACK
BACKLIGHT
[12]
COLOR
[13] VERSION
B
BLUE
G
GREEN
O
ORANGE
R
RED
W
WHITE
Y
YELLOW GREEN
01
ENGLISH-JAPANESE
02
ENGLISH-EURPEAN
03
ENGLISH-RUSSIAN
※All of our STN Panel belong “WIDE TEMPERATURE”
Ver 2007.05
3/18
E
EDGE LED BACKLIGHT
www.sdec.com.tw
LMG-S16D80
CONTENTS
●
0.
1.
2
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
LCM Sample Approval
LCD Module Number System
Mechanical Specification
Mechanical Diagram
Interface Pin Connections
Block And Power Supper Diagram
Environmental absolute maximum ratings
Electrical Characteristics
Optical Characteristics
Optical Definitions
Timing Control
Display Control Instructions
Interface For LCM
CG ROM Pattern
PAGE
2
3
5
5
5
5
6
6
6
6
6
7
10
10
13.
14.
Reliability Condition
Functional Test & Inspection Criteria
11
11
15.
16.
17.
18.
Test – Normal Temperature
Test – Wide Temperature
Precautions Against Product Handling
Warranty
14
15
16
17
Ver 2007.05
4/18
www.sdec.com.tw
LMG-S16D80
1.
Mechanical Specification
ITEM
DOT MATRIX FORMAT
CONTROLLER IC
MODULE DIMENSION
NO BACKLIGHT, EL BACKLIGHT
MODULE DIMENSION
ARRAY LED BACKLIGHT
MODULE DIMENSION
EDGE LED BACKLIGHT (BLUE)
VIEWING DISPLAY AREA
ACTIVE DISPLAY AREA
DOT SIZE
DOT PITCH
z EL USE INVERTER TYPE
INVERTER INPUT
INVERTER OUTPUT
BACKLIGHT HALF-LIFT TIME
z ARRAY LED BACKLIGHT COLOR
BACKLIGHT INPUT
BACKLIGHT HALF-LIFT TIME
z EDGE LED BACKLIGHT COLOR
BACKLIGHT INPUT
BACKLIGHT HALF-LIFT TIME
STANDARD VALUE
160 × 80 DOTS
LC7981 OR EQUIVALENT
UNIT
--
93.0 (W) X 70.0 (H) X 9.5 (T)
mm
93.0 (W) X 70.0 (H) X 14.0 (T)
mm
93.0 (W) X 70.0 (H) X 12.0 (T)
mm
72.0W
67.17W
0.39W
0.42W
×
×
×
×
39.0H
33.57H
0.39H
0.42H
mm
mm
mm
mm
SDEC-I002A
DC +5V
AC 90 ~ 110
V
40
V
400 ~ 700
3,000
YELLOW GREEN OR ORANGE OR RED
DC +4.2V
V
300
30,000
BLUE OR GREEN OR WHITE
DC+3.2V
V
78
3,000 (AVOID LIGHTING CONTINUOUSLY)
mA
Hz
HR.
mA
HR.
mA
HR.
2. Mechanical Diagram
3. Interface Pin Connections
NO SYMBOL LEVEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
4. Block And Power Supper Diagram
FUNCTION
VSS
-Ground
VDD
-Power supply for logic circuit
Vo
-Power supply for LCD circuit
D/I
H/L
Data/Instruction
R/W
H/L
Read / Write
E
Enable Signal
H,H→L
DB0
H/L
Data Bit 0
DB1
H/L
Data Bit 1
DB2
H/L
Data Bit 2
DB3
H/L
Data Bit 3
DB4
H/L
Data Bit 4
DB5
H/L
Data Bit 5
DB6
H/L
Data Bit 6
DB7
H/L
Data Bit 7
/CS
L
Chip enable
/DISP OFF
L
Display off signal
/RES
L
Controller reset
VEE
-Negative voltage output
A
-LED Backlight + (+5V)
K
-LED Backlight - ( 0V)
Ver 2007.05
5/18
www.sdec.com.tw
LMG-S16D80
5. Environmental absolute maximum ratings
ITEM
OPERATING
MIN.
MAX.
-20°C
+70 °C
NOTE 1
-4.9m/s2
-29.4m/s2
Ambient Temperature
Humidity
Vibration
Shock
Remarks:
NOTE (1) :
NOTE (2) :
Ta at 60 °C :
Ta < 40 °C :
Ta > 40 °C :
STORAGE
MIN.
MAX.
-30 °C
+80 °C
NOTE 2
-19.6m/s2
-490.0m/s2
REMARKS
-NOTE 1
Without Condensation
XYZ Directions
XYZ Directions
50 HR Max.
95% RH Max.
Absolute humidity must be lower than the humidity of 95% at 40 °C.
6. Electrical Characteristics
ITEM
Logic Circuit Power Supply
LCD Driver Power Supply
SYMBOL
VDD - VSS
VLCD
VIH
VIL
IDD
IEE
Input Voltage
Power Supply Current
CONDITION
--VDD = 5V±0.25
VDD = 5V
VEE = -10V
MIN
4.75
9.7
0.7*VDD
0
---
TYP
5.0
10.0
-----
MAX
5.25
10.3
VDD
0.3*VDD
10.0
2.0
7. Optical Characteristics
UNIT
V
V
V
V
mA
mA
Ta at 25℃
ITEM
SYM
CONDITION
MIN.
TYPE
MAX.
UNIT
VIEW ANGLE (TOP／BOTTOM)
VIEW ANGLE (LEFT／RIGHT)
CONTRAST RATIO
RESPONSE TIME (RISE)
RESPONSE TIME (DECAY)
θ1 /θ2
φ1 /φ2
CR
TON／Tr
TOFF／Tf
CR≧5
CR≧5
──
──
──
──
──
──
──
──
45/35
35/35
7
160
210
──
──
──
---
deg.
deg.
──
mS
mS
8. Optical Definitions
Response
Time
Contrast
Ration
Brightness of
nonselected segment (B2)
Contrast Ration (K) = ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─
Brightness of
selected segment (B1)
Brightness curve
of nonselected
segment
Nonselected
Condition
Btightness
Btightness
Nonselected
Condition
Rise Time
Fall Time
Brightness
curve of
selected
segment
View
Y (T O P )
Angle
θ2
θ1
X
(Le ft)
X
(R ig h t)
2
Set Point Driving Voltage
EYE
1
Y (B O T T O M )
9. Timing Control
Ver 2007.05
6/18
www.sdec.com.tw
LMG-S16D80
ITEM
Enable cycle time
Enable pulse width High/Low level
Enable rise/fall time
Setup time
Data setup time
Data delay time
Data hold time
Address hold time
Output data hold time
SYMBOL
tCYC
tWEH,tWEL
tEr,tEf
tAS
tDSW
tDDR
tH
tAH
tDH
MIN
1000
450
-140
225
-10
10
20
TYP
----------
MAX
--25
--225
----
UNIT
ns
ns
ns
ns
ns
ns*
ns
ns
ns
Note: * The following load circuit is connected for specification
10. Display Control Instructions
10.1 Description of command
Display is controlled by writing data into the instruction register and 13 data registers. The RS signal distinguishes the instruction register
from the data registers. 8-bit data is written into the instruction register with RS=1, and the code of data register is specified. After that, the
8-bit data is written in the data register and the specified instruction is executed with RS=0. During the execution of the instruction, no new
instruction can be accepted. Since the busy flag is set during this, read the busy flag and make sure it is 0 before writing the next instruction.
10.1.1
Mode Control
Code $“00” (hexadecimal) written into the instruction register specifies the mode control register.
REGISTER
Instruction Register
Mode Control Register
DB5
DB4
1/0
1/0
R/W
0
0
DB3
0
0
1
1
0
0
1
1
0
DB2
0
1
0
1
0
1
0
1
0
1: Master Mode
1: Display ON
10.1.2
DB1
RS
1
0
DB0
DB6
0
0
DB5
0
DB4
0
Cursor/blink
Cursor OFF
Cursor ON
Cursor OFF, Character blink
Cursor blink
Cursor OFF
Cursor ON
Cursor OFF, Character blink
Cursor blink
--
0
0
1
1
DB7
0
0
0
DB3
DB2
0
0
Mode Data
CG
DB1
0
DB0
0
Graphic/Character
Internal
CG
Character Mode
External
CG
--
Graphic Mode
0: Slave Mode *Normal is set Master Mode
0: Display OFF
Set Character Pitch
REGISTER
Instruction Register
Character Pitch Register
R/W
0
0
RS
1
0
DB7
0
DB6
DB5
0
0
(Vp -1) Binary
DB4
0
DB3
0
0
DB2
DB1
DB0
0
0
1
(Hp -1) Binary
Vp indicates the number of vertical dots per character. The space between the vertically-displayed characters is considered for determination.
This value is meaningful only during character display (in the character mode) and becomes invalid in the graphic mode. The Hp indicates the
number of horizontal dots per character in display including the space between horizontally displayed characters. In the graphic mode, the Hp
indicates the number of bits of 1 byte display data to be displayed. Three Hp values:
Hp
6
7
8
DB2
1
1
1
10.1.3
DB1
0
1
1
DB0
1
0
1
Horizontal character pitch 6
Horizontal character pitch 7
Horizontal character pitch 8
Set Number of Characters
REGISTER
Instruction Register
Number of Character Register
R/W
0
0
RS
1
0
DB7
0
0
DB6
0
DB5
0
DB4
DB3
DB2
0
0
0
(Hn -1) Binary
DB1
1
DB0
0
Hn indicates the number of horizontal characters in the character mode r the number of horizontal bytes in the graphic mode. If the total sum
of horizontal dots on the screen is taken as n, n = Hp x Hn. Hn can be set with an even number of 2 to 128 (decimal).
10.1.4
Set Number of Time Division (inverse of display duty ratio)
REGISTER
Instruction Register
Character Pitch Register
R/W
0
0
RS
1
0
DB7
0
DB6
0
DB5
0
DB4
DB3
0
0
(Nx -1) Binary
DB2
0
DB1
1
DB0
1
Nx indicates the number of time division in multiplex display. 1/Nx is a display duty ration. A value of 1 to 128 (decimal) can be set to Nx.
Ver 2007.05
7/18
www.sdec.com.tw
LMG-S16D80
10.1.5
Set Cursor Position
REGISTER
Instruction Register
Cursor Position Register
R/W
0
0
RS
1
0
DB7
0
0
DB6
0
0
DB5
0
0
DB4
0
0
DB3
0
DB2
DB1
1
0
(Cp -1) Binary
DB0
0
Cp indicates the position in a character where the cursor is displayed in the character mode. For example, in 5x7 dot font, the cursor is
displayed under a character by specifying Cp=8 (decimal). The cursor horizontal length is equal to the horizontal character pitch Hp. A value
of 1 to 16 (decimal) can be set to Cp. If a smaller value than the number of vertical character pitches Vp is set (Cp≦Vp), and a character is
overlapped with the cursor, the cursor has higher priority of display (at cursor display ON). If Cp is greater than Vp, no cursor is displayed.
The cursor horizontal length is equal to Hp.
10.1.6
Set Display Start Low Order Address
REGISTER
Instruction Register
Display Start Address Register (low order byte)
10.1.7
R/W RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
1
0
0
0
0
1
0
0
0
0
0
(Start low order address) Binary
Set Display start High Order Address
REGISTER
Instruction Register
Display Start Address Register (high order byte)
R/W RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
1
0
0
0
0
1
0
0
1
0
0
(Start high order address) Binary
These instructions cause display start addresses to be written in the display start address registers. The display start address indicates a RAM
address at which the data displayed at the top left end on the screen is stored. In the graphic mode, the start address is composed of high/low
order 16 bits. In the character display, it is composed of he lower 4 bits of high order address (DB3 - DB4) and 8 bits of low order address.
The upper 4 bits of high order address are ignored.
10.1.8
Set Cursor Address (low order) (RAM write low order address)
REGISTER
Instruction Register
Cursor Address Counter (low order byte)
10.1.9
R/W RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
1
0
0
0
0
1
0
1
0
0
0
(Cursor low order address) Binary
Set Cursor Address (high order) (RAM write high address)
REGISTER
Instruction Register
Cursor Address Counter (high order byte)
R/W RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
0
1
0
0
0
0
1
0
1
1
0
0
(Cursor high order address) Binary
These instructions cause cursor addresses to be written in the cursor address counters. The cursor address indicates and address for sending or
receiving display data and character codes to or from the RAM. Namely, data at address specified by the cursor address are read/written. In
the character mode, the cursor is displayed at the digit specified by the cursor address. A cursor address consists of the low-order address (8
bits) and the high-order address (8 bits). Satisfy the following requirements.
1
2
3
When you want to rewrite (set) both the low order address Set the low order address and then set the high order
and the high order address.
address.
When you want to rewrite only the low order address.
Don‘t fail to set the high order address again after setting
the low order address.
When you want to rewrite only the high order address.
Set the high order address. You don‘t have to set the
low order address again.
The cursor address counter is a 16 bit up-count with SET and RESET functions. When the bit N Changes from 1 to 0, the bit N+1 is added by
1. When setting the low order address, the LSB (bit 1) of the high order address is added by 1 if the MSB (bit *) of the low order address
changes from 1 to 0. Therefore, set both the low order address and the high order address as shown in above table.
10.1.10
REGISTER
Instruction Register
RAM
Write Display Data
R/W
0
0
RS
1
0
DB7
0
DB6
0
DB5
DB4
DB3
DB2
DB1
0
0
1
1
0
MSB (pattern data, character code) LSB
DB0
0
After the code $“OC” is written into the instruction register with RS=1, 8 bit data with RS=0 should be written into the data register. This data
is transferred to the RAM specified by the cursor address as display data or character code. The cursor address is increased by 1 after this
operation.
10.1.11
REGISTER
Instruction Register
RAM
Read Display Data
R/W
0
0
RS
1
0
DB7
0
DB6
0
DB5
DB4
DB3
DB2
DB1
0
0
1
1
0
MSB (pattern data, character code) LSB
DB0
1
Data can be read from the RAM with RS=0 after writing code $“0D” into the instruction register. The read procedure is as follows:
This instruction outputs the contents of data output register on Data Bus (DB0 to DB7) and then transfers RAM data specified by a cursor
address to the data output register, also increasing the cursor address by 1. After setting the cursor address, correct data is not output at the
first read but at the second time. Thus, make one dummy read when reading data after setting the cursor address.
Ver 2007.05
8/18
www.sdec.com.tw
LMG-S16D80
10.1.12
Clear Bit
REGISTER
Instruction Register
Bit Set Register
10.1.13
R/W
0
0
RS
1
0
DB7
0
0
DB6
0
0
DB5
0
0
DB4
0
0
DB3
1
0
DB2
DB1
DB0
1
1
0
(NB-1)Binary
R/W
0
0
RS
1
0
DB7
0
0
DB6
0
0
DB5
0
0
DB4
0
0
DB3
1
0
DB2
DB1
DB0
1
1
1
(NB-1)Binary
Set Bit
REGISTER
Instruction Register
Bit Set Register
The Clear/Set bit instruction sets 1 bit in a byte of display data RAM to 0 or 1, respectively. The position of the bit in a byte is specified by
NB and RAM address is specified by cursor address. After the execution of the instruction, the cursor address is automatically increased by 1.
NB is a value of 1 to 8. NB=1 and NB=8 indicates LSB and MSB, respectively.
10.1.14
Read Busy Flag
REGISTER
R/W
0
Busy Flag
RS
1
DB7
1/0
DB6
DB5
DB4
DB3
*
DB2
DB1
DB0
When the read mode is set with RS=1, the busy flag is output to DB7. The busy flag is set to 1 during the execution of any of instructions (1)
to (13). After the execution, it is set to 0. The next instruction can be accepted. No instruction can be accepted when busy flag=1. Before
executing an instruction or writing data, perform a busy flag check to make sure that busy flag is 0. When data is written in the register
(RS=1), no busy flag changes. Thus, no busy flag check is required just after the write operation into the instruction register with RS=1. The
busy flag can be read without specifying any instruction register.
10.2 Display variables
Hp
RD0
Vp
Nx
RD7
□■■■□□□□ ■■■■□□□
■□□□■□□□ ■□□□■□□
■□□□■□□□ ■□□□■□□
■□□□■□□□ ■■■■□□□
■■■■■□□□ ■□□□■□
■□□□■□□□ ■□□□■□
■□□□■□□□ ■■■■□□
□□□□□□□□ □□□□□□
□□□□□□□□ ■■■■■
□□□□□
□□□
□□
STA
Cp
■■■■■□□□
□□□□■□□□
□□□■□□□□
□□■□□□□□
□■□□□□□□
■□□□□□□□
■■■■■□□□
□□□□□□□□
□□□□□□□□
□□□□□□□□
CURA
□□□□□□□□
□■■■□□□□
■□□□■□□□
■□□□■□□□
■□□□■□□□
■□□□■□□□
■□□□■□□□
□■■■□□□□
□□□□□□□□
□□□□□□□□
Hn (digits)
Symbol
Name
Hp
Horizontal character pitch
Number of horizontal
Hn
characters
Vp
Vertical character pitch
Cp
Cursor position
nx
Number of time division
Meaning
Value
Lateral character pitch
6 to 8 dots
Number of lateral characters per line (number of digits) in the
2 to 128 digits (an even
character mode or number of bytes per line in the graphic mode. number)
Longitudinal character pitch.
1 to 16 dots
Line number on which the cursor can be displayed.
Inverse of display duty ratio
1 to 128 lines
Note: If the number of vertical dots on screen is taken as m, and the number of horizontal dots as n,
1/m = 1/Nx = display duty ratio
n = Hp x Hn, m/Vp = Number of display lines
Cp≦Vp
10.3 Initialize LCM register set list
Register number
Character mode
Graphics mode
Ver 2007.05
0H
1CH
12H
1H
77H
77H
2H
13H
13H
9/18
3H
4FH
4FH
4H
07H
07H
8H
00H
00H
9H
00H
00H
AH
00H
00H
BH
00H
00H
www.sdec.com.tw
LMG-S16D80
11. Interface For LCM
1.1 Interface to 80 family
11.2 Interface to 68 family
12. CG ROM Pattern
Ver 2007.05
10/18
www.sdec.com.tw
LMG-S16D80
13.
Reliability Condition
TN Type
Normal Temp.
Wide Temp.
Viewing Horizontal (Φ1/Φ2)
±30°
±30°
Angle
Vertical (Θ2/Θ1)
15°to 35°
15°to 35°
Operating Temperature
0 to 50℃
-20 to 70℃
Storage Temperature
-10 to 60℃
-30 to 80℃
High Temperature (Power Off)
240 Hours
240 Hours
@60℃
@80℃
Low Temperature (Power Off)
240 Hours
240 Hours
@-10℃
@-30℃
High Temperature (Power On)
240 Hours
240 Hours
@50℃
@70℃
Low Temperature (Power On)
240 Hours
240 Hours
@0℃
@-20℃
High Temperature & High
40℃/90%RH
40℃/90%RH
Humidity (Power Off)
240 Hours
240 Hours
Thermal Shock
C
A 60min@0℃
60min@-20℃
5 Cycle
B
B 5min@25℃
5min@25℃
A
C 60min@50℃
60min@70℃
50,000 Hours
50,000 Hours
LCD Lift (25℃/ 45%RH)
STN/FSTN Type
Normal Temp.
Wide Temp.
±40°
±40°
35°to 55°
35°to 55°
*
0 to 50℃
-20 to 70℃
*
-10 to 60℃
-30 to 80℃
240 Hours
240 Hours
@60℃
@80℃
240 Hours
240 Hours
@-10℃
@-30℃
240 Hours
240 Hours
@50℃
@70℃
240 Hours
240 Hours
@0℃
@-20℃
40℃/90%RH
40℃/90%RH
240 Hours
240 Hours
60min@0℃
60min@-20℃
5min@25℃
5min@25℃
60min@50℃
60min@70℃
50,000 Hours
50,000 Hours
*
Wide temp. version may not available for some products, Please consult our sales engineer or representative.
14. Functional Test & Inspection Criteria
14.1 Sample plan
Sample plan according to MIL-STD-105D level 2, and acceptance/rejection criteria is.
Base on :
Major defect : AQL 0.65
Minor defect : AQL 2.5
14.2Inspection condition
Viewing distance for cosmetic inspection is 30cm with bare eyes, and under an environment of 800 lus (20W) light
intensity. All direction for inspecting the sample should be within 45°against perpendicular line.
14.3Definition of Inspection Zone in LCD
A
B
C
Zone A :
Zone B :
Zone C :
Note :
Character / Digit area
Viewing area except Zone A ( Zone A + Zone B = minimum Viewing area )
Outside viewing area ( invisible area after assembly in customer’s product )
As a general rule, visual defects in Zone C are permissible, when it is no trouble for quality and
assembly of customer’s product.
14.4Major Defect
All functional defects such as open ( or missing segment ), short, contrast differential, excess power consumption,
smearing, leakage, etc. and overall outline dimension beyond the drawing. Are classified as major defects.
Ver 2007.05
11/18
www.sdec.com.tw
LMG-S16D80
14.5 Inspection Parameters And Glass Pixel(偏光板和玻璃圖像檢驗)
NO
1
Polarizer(偏光板)
Black or White spots And
Piercing
(黑/白點和刺孔)
Criteria
Dimension
(面積)
Acceptable number
(可接受數量)
D＜0.15
*
0.15≦D≦0.2
4
0.2≦D≦0.25
2
D≦0.3
0
D/面積=(Length/長度+Width/寬度)/2
2
Scratch
(刮傷)
X(mm)
Y(mm)
Acceptable number
(可接受數量)
*
3.0≧L
0.04≧W
*
0.06≧W
4
2.0≧L
0.08≧W
2
－
0.1≧W
X：Length(長度)
3
Air Bubbles
(between glass & polarizer)
氣泡(玻璃跟偏光板之間)
0
Y：Width(寬度)
Dimension
(面積)
Acceptable number
(可接受數量)
D≦0.15
*
0.15＜D≦0.25
2
0.25＜D
0
*：Disregard
Ver 2007.05
=>
* ：Disregard(忽略)
*：Disregard(忽略)
(忽略)
12/18
www.sdec.com.tw
LMG-S16D80
(1)Pixel shape (with Dent) /圖像凹度
●Less than 0.152 mm is no counted
(小於 0.152mm 者不計)
(2)Pixel shape (with Projection)/圖像凹度
Should not be connected
next pixel
(點與點間不可先連接)
4
Glass of Pixel
(玻璃的圖像)
(3)Deformation/變形
( X + Y ) / 2 ≦ 0.15mm
●Less than 0.1 mm is no counted
(小於 0.15mm 者不計)
(4) Deformation/變形
( X + Y ) / 2 ≦ 0.3mm
●Less than 0.3 mm is no counted
(小於 0.3mm 者不計)
Ver 2007.05
13/18
www.sdec.com.tw
LMG-S16D80
15. Test (測試條件) – Normal Temperature (常溫)
No change no display and in operation under the following text condition.
(在不改變原先顯示下進行以下測試操作)
Conditions ： Unless otherwise specified, test will be conducted under the following condition.
Temperature ： 20±5 ℃
Humidity： 40±5%RH
Tests will be not conducted under functioning state.
(條件：除非其他特殊情況，否則測試將以溫度：20±5 ℃，濕度：40±5%RH 為主)
NO
1
2
3
4
Parameter
Conditions
High Temperature 50℃±2 ℃ , 96 hrs (operation state)
(96 小時，溫度 50℃±2 ℃電源開啟的操作情況下)
Operating
Low Temperature 0℃±2 ℃ , 96 hrs (operation state)
(96 小時，溫度 0℃±2 ℃電源開啟的操作情況下)
Operating
Notes
High Temperature 60℃±2 ℃ , 96 hrs
(96 小時，溫度 60℃±2 ℃電源關閉靜態操作下)
Storage
Low Temperature -10℃±2 ℃ , 96 hrs
(96 小時，溫度-10℃±2 ℃電源關閉靜態操作下)
Storage
2
1
1,2
5
Damp Proof
Test
40℃±2 ℃ , 85 ~ 90%RH , 96hr
(96 小時，溫度：40℃±2 ℃，濕度：85~90%RH
電源關閉靜態操作下)
1,2
6
Vibration Test
Total fixed amplitude ： 1.5 mm (完全固定輻射：1.5mm)
Vibration Frequency ： 10 ～ 55 Hz (震動頻率：10~55 Hz)
3
One cycle 60 seconds to 3 directions of X , Y , Z for
each 15 minutes (每一個循環 X，Y，Z 軸方向各做 60 秒，連續
做 5 次，共計 15 分鐘)
7
Shock Test
To be measured after dropping from 60cm high on the concrete
surface in packing state. (包裝材從 60 公分高的地方向地面落下)
Dropping method comer
dropping (角落落下方式)
A comer：once
Edge dropping (側邊落下)
B , C , D edge : once
Face dropping (表面落下)
E , F , G face : once
Note 1：No dew condensation to be observed. (不要在＂水氣凝結點＂下觀察)
Note 2：The function test shall be conducted after 4 hours storage at the normal
Temperature and humidity after removed from the test chamber
(從實驗室移出後，放在一般常溫 (溫度：25℃，濕度：45%RH)，
且四小時後通電流或電壓，看它是否能正常動作)
Note 3：Vibration test will be conducted to the product itself without putting it in a container.
(在震動測試下，產品本身不需容器即能自行傳導)
Ver 2007.05
14/18
www.sdec.com.tw
LMG-S16D80
16. Test (測試條件) – Wide Temperature (廣溫)
No change no display and in operation under the following text condition.
(在不改變原先顯示下進行以下測試操作)
Conditions ： Unless otherwise specified, test will be conducted under the following condition.
Temperature ： 20±5 ℃
Humidity： 40±5%RH
Tests will be not conducted under functioning state.
(條件：除非其他特殊情況，否則測試將以溫度：20±5 ℃，濕度：40±5%RH 為主)
NO
1
2
3
4
Parameter
Conditions
High Temperature 70℃±2 ℃ , 96 hrs (operation state)
(96 小時，溫度 70℃±2 ℃電源開啟的操作情況下)
Operating
Low Temperature -20℃±2 ℃ , 96 hrs (operation state)
(96 小時，溫度-20℃±2 ℃電源開啟的操作情況下)
Operating
Notes
High Temperature 80℃±2 ℃ , 96 hrs
(96 小時，溫度 80℃±2 ℃電源關閉靜態操作下)
Storage
Low Temperature -30℃±2 ℃ , 96 hrs
(96 小時，溫度-30℃±2 ℃電源關閉靜態操作下)
Storage
2
1
1,2
5
Damp Proof
Test
40℃±2 ℃ , 85 ~ 90%RH , 96hr
(96 小時，溫度：40℃±2 ℃，濕度：85~90%RH
電源關閉靜態操作下)
1,2
6
Vibration Test
Total fixed amplitude ： 1.5 mm (完全固定輻射：1.5mm)
Vibration Frequency ： 10 ～ 55 Hz (震動頻率：10~55 Hz)
3
One cycle 60 seconds to 3 directions of X , Y , Z for
each 15 minutes (每一個循環 X，Y，Z 軸方向各做 60 秒，連續
做 5 次，共計 15 分鐘)
7
Shock Test
To be measured after dropping from 60cm high on the concrete
surface in packing state. (包裝材從 60 公分高的地方向地面落下)
Dropping method comer
dropping (角落落下方式)
A comer：once
Edge dropping (側邊落下)
B , C , D edge : once
Face dropping (表面落下)
E , F , G face : once
Note 1：No dew condensation to be observed. (不要在＂水氣凝結點＂下觀察)
Note 2：The function test shall be conducted after 4 hours storage at the normal
Temperature and humidity after removed from the test chamber
(從實驗室移出後，放在一般常溫 (溫度：25℃，濕度：45%RH)，
且四小時後通電流或電壓，看它是否能正常動作)
Note 3：Vibration test will be conducted to the product itself without putting it in a container.
(在震動測試下，產品本身不需容器即能自行傳導)
Ver 2007.05
15/18
www.sdec.com.tw
LMG-S16D80
17. Precautions Against Product Handling [產品使用注意事項]：
The following precautions will guide you in handling our product correctly.
[下列警戒引導正確地使用產品]
17.1 Care of the LCD module against static electricity discharge. [LCD 模組靜電注意事項]
17.1.1 When working with the module, be sure to ground your body and any electrical
equipment you may be using. We strongly recommend the use of anti static mats (made of
rubber), to protect work tables against the hazards of electrical shock.
[操作模組時，避免操作者身體接地及任何造成靜電的設備同時使用，強烈建議(橡膠製)
抗靜電墊的使用，以免工作台面遭受到電氣干擾]
17.1.2 Slowly and carefully remove the protective film from the LCD module, since this
operation
can generate static electricity.
[緩慢小心地移除 LCD 模組上的保護膜，以防靜電產生]
17.1.3 Avoid the use of work clothing made of synthetic fibers. We recommend cotton clothing
or other conductivity-treated fibers.
[避免穿著人造合成的工作服，建議棉質或是有傳導性的纖維質料]
17.2 Liquid crystal display devices (LCD devices) [液晶螢幕顯示器的組成]
17.2.1 The polarizer adhering to the surface of the LCD is made of a soft material.
Guard against scratching it. [偏光板是軟性原料製成，請勿刮傷]
17.2.2 The LCD device panel used in the LCM is made of plate glass. Avoid any strong mechanical
shock. Should the glass break handle it with care.
[模組使用的玻璃為平面玻璃，避免任何強烈的機械撞擊，且觸碰時請小心]
17.3 When the LCD module alone must be stored form long periods of time
[當 LCD 模組須長時間存放時]
17.3.1 Protect the modules from excessive external forces. [避免外力壓迫]
17.3.2 Protect the modules from high temperature and humidity. [避免處於高溫高濕下]
17.3.3 Keep the modules out of direct sunlight or direct exposure to ultraviolet rays.
[遠離陽光曝曬或直接曝露在紫外線下]
17.4 Use the module with a power supply that is equipped with an overcurrent protector circuit, since the
module is not provided with this protective feature.
[因為模組本身沒有防護，所以模組的供應器應配有過高電流的保護迴路]
17.5 Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should hands or
clothing come in contact with LCD fluid, wash immediately with soap.
[LCD 破裂液晶外漏時，切勿食下液晶；若手或衣服接觸到液晶，請立刻用肥皂清洗]
17.6 Conductivity is not guaranteed for models that use metal holders where solder connections between
the metal holder and the PCB are not used. Please contact us to discuss appropriate ways to assure
conductivity.
[當金屬框並沒焊接於 PCB 板上時，無法保證使用金屬框是具有傳導性，請連絡我們商討適當
方式傳導]
17.7 For models which use CCFL [CCFL 的模組]:
17.7.1 High voltage of 1000V or greater is applied to the CCFL cable connector area.
[CCFL 排線連接器用於 1000V 以上的高電壓]
17.7.2 Protect CCFL cables from rubbing against the unit and thus causing the wire jacket to become
worn. [CCFL 排線必須有保護 CCFL 與模組磨擦，以防 CCFL 外殼受到損害]
17.7.3 The use of CCFLs for extended periods of time at low temperatures will significantly shorten
their service life. [長時間低溫使用 CCFL 會明顯縮減其使用壽命]
Ver 2007.05
16/18
www.sdec.com.tw
LMG-S16D80
17.8 For models which use touch panels [觸控式面板模組]:
17.8.1 Do not stack up modules since they can be damaged by components on neighboring modules.
[勿堆疊模組以防損壞]
17.8.2 Do not place heavy objects on top of the product. This could cause glass breakage.
[勿將重物放置在產品上，會導致玻璃破損]
17.9 For models which use COG & TAB [COG 及 TAB 模組]:
17.9.1 The mechanical strength of the product is low since the IC chip is faces out unprotected from
the rear. Be sure to protect the rear of the IC chip from external forces.
[由於 IC 晶片表面無防護，所以抗壓力有限，須加強保護以防外力]
17.9.2 Given the fact that the rear of the IC chip is left exposed, in order to protect the unit from
electrical damage, avoid installation configurations in which the rear of the IC chip runs the
risk of making any electrical contact.
[勿暴露 IC 晶片以防電氣干擾，且避免安裝 IC 時有任何電子接觸]
17.10 Models which use flexible cable, heat seal, or TAB [加有軟排線、熱封條或 TAB 的模組]:
17.10.1 In order to maintain reliability, do not touch or hold by the connector area.
[以維持產品信賴度，請勿觸碰或握住連接器]
17.10.2 Avoid any bending, pulling, or other excessive force, which can result in broken
connections. [避免彎曲、拉扯或過度力量，會造成連接器損壞]
17.11 In case of acrylic plate is attached to front side of LCD panel, cloudiness (very small cracks) can
occur on acrylic plate, being influenced by some components generated from polarizer film.
Please check and evaluate those acrylic materials carefully before use.
[貼在 LCD 玻璃前面的壓克力板若有模糊情況(微小裂縫)，即會影響偏光板；使用前請仔細確
認壓克力材質]
17.12 In case of buffer material such as cushion/gasket is assembled into LCD module, it may have an
adverse effect on connecting parts (LCD panel-TCP/ HEAT SEAL/ FPC, PCB-TCP/HEAT
SEAL/FPC, TCP-HEAT SEAL, TCP-FPC, HEAT SEAL-FPC) depending on its materials.
Please check and evaluate these materials carefully before use.
[ 緩 衝 原 料 像 是 減 震 墊 / 襯 墊 ， 或 許 會 對 連 接 器 (LCD panel-TCP/ HEAT SEAL/ FPC,
PCB-TCP/HEAT SEAL/FPC, TCP-HEAT SEAL, TCP-FPC, HEAT SEAL-FPC)造成反效果，使用
前請仔細確認材料]
18. Warranty [保證]：
This product has been manufactured to your company’s specifications as a part for use in your company’s
general electronic products. It is guaranteed to perform according to delivery specifications. For any other
use apart from general electronic equipment, we cannot take responsibility if the product is used in
medical devices, nuclear power control equipment, aerospace equipment, fire and security systems, or any
other applications in which there is a direct risk to human life and where extremely high levels of
reliability are required. If the product is to be used in any of the above applications, we will need to enter
into a separate product liability agreement.
[此產品的製造是依照客戶的規格，被使用於客戶的一般電子產品上，保證產品製作根據出貨的規
格，若產品的使用不是在一般電子設備，而組裝於下列產品上則無法受理（如醫療產品、核心電源
控制設備、航空設備、防火及保全系統，或任何相關儀器會直接影響人類生命等），若模組使用於
上述的儀器，則需商討各別產品責任義務的協定]
Ver 2007.05
17/18
www.sdec.com.tw
LMG-S16D80
18.1 We cannot accept responsibility for any defect, which may arise after the application of strong
external force to the product.
[不受理因強大外力衝擊造成產品的缺陷]
18.2 We cannot accept responsibility for any defect, which may arise from additional manufacturing of the
product (including disassembly and reassembly), after product delivery.
[不受理產品出貨後，因額外加工(包含拆裝及重新封包)造成的缺陷]
18.3 We cannot accept responsibility for any defect, which may arise due to the application of static
electricity after the product, has passed your company’s acceptance inspection procedures.
[不受理通過貴公司檢驗流程後，由於靜電造成產品的缺陷]
18.4 We cannot accept responsibility for intellectual property of a third party, which may arise through the
application of our product to your assembly with exception to those issues relating directly to the
structure or method of manufacturing of our product.
[不受理因在客戶產品生產線端所產生的第三人智慧財產權責任，除非與我司生產製造方法有直
接關係的問題]
18.5 When the product is in CCFL models, CCFL service life and brightness will vary according to the
performance of the inverter used, leaks, etc. We cannot accept responsibility for product performance,
reliability, or defect, which may arise.
[產品是 CCFL 模組時，CCFL 的壽命及亮度將取決於連接器的性能、漏電量等；無法受理因
CCFL 造成產品性能的缺陷]
18.6 SDEC will not be held responsible for any quality guarantee issue for defect products longer than
1(one) year from SDEC production which ever comes later.
[出廠超過一年的瑕疵品，任何品質擔保則不受理]
Ver 2007.05
18/18
www.sdec.com.tw