Download SERVICE MANUAL

AKRON® TM
STREAMLINE
GYNAE 1/2/3
Models
2251. 2252, 2351, 2352
2254, 2354
2255, 2355
2256, 2257
SERVICE MANUAL
SM ENGLISH
794-064-02
General Maintenance including Gas Strut
It is recommended that the following checks and adjustments are carried out at minimum
of twice a year and more frequently if the couch is in constant use.
1.
The framework of the couch is of steel construction and coated with an epoxy paint
finish. This is resistant to most cleaning substances.
2.
The major pivot points need to be lubricated sparingly with oil. Care should be taken
to keep oil away from the upholstery.
3.
All nuts should be checked and tightened where necessary Care should be taken
not to over tighten the nuts on the pivot points as this may cause them to bind.
4.
Air tubes should be checked to ensure that they are not pinched.
5.
Disconnect the mains supply and check the following;
Note: - all electrical should be carried out by a suitably qualified person.
Electric cables and mains plug should be inspected for damage and replaced where
necessary. In addition, electrical safety checks for earth continuity (class I
equipment only) and earth leakage checks should also be carried out.
The correct value fuse of 5 amps and ASTA approved to BS1362 MUST be used.
6.
The upholstered top is manufactured using fire retardant vinyl. This tends to go
brittle if oil or grease (including body oils) are left on it. The upholstery should be
cleaned with warm soapy water after use. The use of detergents is not
recommended although a suitable sterilisation fluid is acceptable. Use of a couch
cover or towel will help prolong the life of the upholstery.
7.
Woodscrews, used to secure the upholstery, should be checked and tightened or
replaced where necessary.
8.
The hinge pins on the head and foot sections should be checked to ensure that they
have not moved within the hinge tubes. Ensure Circlip is located fully in groove in
pin. If the Circlip is not located correctly push firmly into groove to secure pin.
9.
Gas strut controls should be checked for a small amount of clearance between the
operating flap and the release pin, throughout the range of movement. Should
clearance be inadequate, or the top sinks whilst in use, the following adjustments
should be made; firmly grasp the body of the strut and rotate in an anti-clockwise
direction. Check for clearance and repeat as necessary.
Should the gas strut fail to operate, refer to the above adjustment but rotate in a
clockwise direction.
1
Manufacturers Details
Huntleigh Healthcare
Akron Products Division
1 Farthing Road
Ipswich
Suffolk
IP1 5AP
England
Tel:
Fax:
(0) 1473 461042
(0) 1473 462924
Huntleigh Healthcare, Akron Products Division
A Member of the Huntleigh Technology PLC Group of Companies
© Huntleigh Technology PLC 2007.
Register of Drawings/Revision History
DCN Number
1278
1256
Updated Drawings
Current Issue Status
of Drawing
Current Revision
of Service Manual
2R11108Z
2R11107Z
-
2
2
-
2
2
1
2
Date
18/02/08
28/11/07
ITEM QTY
1
1
2
2
3
2
4
1
5
1
6
2
7
4
8
4
9
4
10
4
11
4
12
4
13
1
14
4
15
4
16
4
17
12
18
4
19
4
20
8
21
4
22
4
23
1
24
5
25
1
26
16
27
16
28
4
29
4
30
1
31
4
32
1
THE FRONT AND REAR ACTUATOR MOUNTS 3A10004P (4) AND 3A10005P (5)
AND RELATED FIXINGS ARE TO BE LOOSELY ATTACHED TO THE BASE.
THESE BRACKETS WILL THEN BE CORRECTLY POSITIONED AND
SECURED IN THE CORRECT ORIENTATION DURING THE CREATION
OF THE TOP LEVEL PRODUCT
26
26
26
2
26
27
27
18
4
2
28
27
31
26
22
29
11
27
27
27
32
26
26
27
24
20
26
17
12
27
10
19
17
27
26
7
26
27
6
17
10
18
20
7
31
14
26
26
1
14
26
14
17
SHEET 1 OF 2
17
17
28
29
31
18
10
29
13
15
8
21
25
9
20
3
17
12
24
24
28
5
11
20
31
30
19
15
29
3
19
21
18
17
22
6
16
8
8
9
UL
28
20
21
Gary Cherrington
I am approving this document
2008.01.16 10:41:03 Z
7
7
15
UNCONTROLLED WHEN PRINTED
22
24
5U1116Z 225kg WARNING
LABEL. REFER TO RAM
KIT BILL OF MATERIALS
17
15
20
20
14
16
17
DESCRIPTION
Retractable Base Frame
H Section
H Section Link
Front Actuator Mounting Bracket
Rear Actuator Mount
Wheel Cam
Wheel Plunger
3" Castor
M10x20 Socket Head Set screw
M10x100mm Hex Bolt
3/4 Grey End Cap
3/4 Open Starlock
M10 Half Nut
M10 Benton Lock Nut Z/P
M10 Nyloc Nut
M10 Spring Washer
M10 Washer Flat Form B
1/4"x1" Seloc Pin
1700x19 Spring Ring
M10 White Nut Cap
1 1/2"x3/4"x16G Grey Insert
40x40 Moulded End Cap
40x40x2.5mm Insert
40x40x2.5 Grey Insert
10mm Foot Adjustment Stud
50x25x2.5 Grey Insert
Bronze Flanged Bush
Nylon Foot Rubber
Pedal Rubber
Huntleigh Akron Label
Pedal Sticker
Streamline 225 Product Label
10
26
20
21
ISSUE No.
4
0
2
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
3
1
0
17
11
23
11
26
27
17
12
19
12
27
PART No.
3A10001P
3A10002P
3A10003P
3A10004P
3A10005P
3A10006R
3A10007Z
5H0402A
5J8058R
5J8074A
5L0707L
5L0906Z
5L3319A
5L3319B
5L3319C
5L3351K
5L3362K
5M0408C
5M4296S
5N0057X
5N1107E
5N3737M
5N3737V
5N3744Z
5N3782U
5N3944Z
5P8000Z
5T0028Z
5T3200Z
5U1006Z
5U1066Z
5U1113Z
24
C
16
9
C OPYRIGHT. HUNT LEIGH
T ECHNOLOGY PLC 2008
DRAWN
G Mullenger
CAD NO
2R11001Z
THIS DRAWING IS NOT TO BE LOANE D
TO THIRD PA RTIES OR USED WITHOUT DATE
13/03/2006
WRITTEN CONS ENT OF HUNTLEIGH CHECKED &
AK RON LIMITED
APPROVED
TI TLE
Streamline Retractable Base
Patient Posit ioning Solut ions
1 FART HI NG ROAD
I PSWICH, SUFF OLK
I P1 5AP. ENGLAND
T EL: +44(0)1473 461042
F AX: +44(0)1473 462924
www.hunt leigh-akron.com
REVISION STATUS
2
I SSUE
3
4
5
DAT E
1/07 4/07 8/07 11/07
DCN
1234 1243 1253 1268
ASSEMBLY
2R11001Z
I SSUE
5
ITEM QTY
1
1
2
2
3
2
4
1
5
1
6
2
7
4
8
4
9
4
10
4
11
4
12
4
13
1
14
4
15
4
16
4
17
12
18
4
19
4
20
8
21
4
22
4
23
1
24
5
25
1
26
16
27
16
28
4
29
4
30
1
31
4
32
1
27
UNCONTROLLED WHEN PRINTED
12
10
12
20
11
20
14
11
14
2
27
27
27
10
UPPER CROSS
SECTION A-A
2
2
1
20
15
3
27
4
20
3
27
LOWER CROSS
SECTION B-B
27
27
15
STREAMLINE LIFTING MECHANISM
PART No.
3A10001P
3A10002P
3A10003P
3A10004P
3A10005P
3A10006R
3A10007Z
5H0402A
5J8058R
5J8074A
5L0707L
5L0906Z
5L3319A
5L3319B
5L3319C
5L3351K
5L3362K
5M0408C
5M4296S
5N0057X
5N1107E
5N3737M
5N3737V
5N3744Z
5N3782U
5N3944Z
5P8000Z
5T0028Z
5T3200Z
5U1006Z
5U1066Z
5U1113Z
ISSUE No.
4
0
2
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
3
1
0
DESCRIPTION
Retractable Base Frame
H Section
H Section Link
Front Actuator Mounting Bracket
Rear Actuator Mount
Wheel Cam
Wheel Plunger
3" Castor
M10x20 Socket Head Set screw
M10x100mm Hex Bolt
3/4 Grey End Cap
3/4 Open Starlock
M10 Half Nut
M10 Benton Lock Nut Z/P
M10 Nyloc Nut
M10 Spring Washer
M10 Washer Flat Form B
1/4"x1" Seloc Pin
1700x19 Spring Ring
M10 White Nut Cap
1 1/2"x3/4"x16G Grey Insert
40x40 Moulded End Cap
40x40x2.5mm Insert
40x40x2.5 Grey Insert
10mm Foot Adjustment Stud
50x25x2.5 Grey Insert
Bronze Flanged Bush
Nylon Foot Rubber
Pedal Rubber
Huntleigh Akron Label
Pedal Sticker
Streamline 225 Product Label
2
1
REFER TO UPPER H FRAME
CROSS SECTION A-A
2
3
29
28
28
IT IS IMPORTANT TO ENSURE THAT THE
INSERT (22) IS POSITIONED CORRECTLY IN
THE BASE FRAME. IF THIS IS NOT DONE
CORRECTLY THE MECHANISM
WILL NOT OPERATE
18
29
6
22
7
19
29
28
8
22
6
IMPORTANT
WHEN FITTING LINK BARS 3A10003P
ENSURE THAT THE THREE HOLES
ARE POSITIONED AWAY FROM THE
RAM END OF THE BASE FRAME
19
7
STREAMLINE RETRACTABLE
PEDAL MECHANISM
8
7
8
19
Gary Cherrington
I am approving this document
2008.01.16 10:41:31 Z
REFER TO LOWER LINK BAR
CROSS SECTION B-B
C
SHEET 2 OF 2
C OPYRIGHT. HUNT LEIGH
T ECHNOLOGY PLC 2008
DRAWN
G Mullenger
CAD NO
2R11001Z
THIS DRAWING IS NOT TO BE LOANE D
TO THIRD PA RTIES OR USED WITHOUT DATE
13/03/2006
WRITTEN CONS ENT OF HUNTLEIGH CHECKED &
AK RON LIMITED
APPROVED
TI TLE
Streamline Retractable Base
Patient Posit ioning Solut ions
1 FART HI NG ROAD
I PSWICH, SUFF OLK
I P1 5AP. ENGLAND
T EL: +44(0)1473 461042
F AX: +44(0)1473 462924
www.hunt leigh-akron.com
UL
REVISION STATUS
2
I SSUE
3
4
5
DAT E
1/07 4/07 8/04 11/07
DCN
1234 1243 1253 1268
ASSEMBLY
2R11001Z
I SSUE
5
ITEM QTY
1
2
2
2
3
2
4
1
5
1
6
1
7
1
8
1
9
1
10
1
11
3
4
12
13
2
14
4
15
6
16
4
17
4
18
2
19
4
20
4
21
4
22
12
23
2
24
2
25
8
26
4
4
27
28
2
29
16
30
16
31
2
32
2
33
1
34
1
35
1
36
1
SHEET 1 OF 2
29
UNCONTROLLED WHEN PRINTED
29
29
29
2
4
2
30
25
27
29
21
26
23
30
22
17
12
30
14
19
30
36
30
30
30
29
30
20
29
29
15
29
27
29
29
30
11
18
22
1
14
22
19
22
22
12
25
16
23
14
25
22
25
22
7
7
16
21
12
20
17
20
11
5
5U1116Z 225kg WARNING
LABEL. REFER TO RAM
KIT BILL OF MATERIALS
12
34
19
1
24
21
25
22
26
28
18
15
33
28
13
32
DESCRIPTION
Linking Lug
H Section
H Section Link
Front Actuator Mounting Bracket
Rear Actuator Mount
Large Wheel Base Frame
Link Bar
Extended Hexagonal Bar
Hexagonal Bar
2044XSX125R36-32S30 Direcl Castor
2046UAP125R36-32S30 Locking Castor
M6x10 Capped Allen Screw
M6x20 Hex Set Screw
M10x100mm Hex Bolt
1/4 Flat Washer
3/4 Grey End Cap
3/4 Open Starlock
M6 Nyloc Nut
M6 Shakeproof Washer
M10 Benton Lock Nut Z/P
M10 Nyloc Nut
M10 Washer Flat Form B
12mm Starlock Capped
1/4"x1" Seloc Pin
M10 White Nut Cap
1 1/2"x3/4"x16G Grey Insert
1 1/2 x 10G Grey End Cap
40x40x2.5 Grey Insert
50x25x2.5 Grey Insert
Bronze Flanged Bush
Nylon Foot Rubber
Pedal Rubber
Huntleigh Akron Label
Pedal Sticker
Pedal Sticker
Streamline 225 Product Label
27
27
25
19
ISSUE No.
0
0
2
0
0
2
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
3
1
1
0
22
3
22
24
29
14
26
31
22
17
35
32
29
6
11
16
26
25
9
13
17
29
20
15
25
21
3
22
29
15
29
30
PART No.
3A03263Z
3A10002P
3A10003P
3A10004P
3A10005P
3A10010P
3A10011P
3A10014R
3A10018R
5H1204F
5H1212F
5J7655C
5J7658N
5J8074A
5L0362V
5L0707L
5L0906Z
5L2919C
5L2955K
5L3319B
5L3319C
5L3362K
5L3503Z
5M0408C
5N0057X
5N1107E
5N1125L
5N3744Z
5N3944Z
5P8000Z
5T0028Z
5T3200Z
5U1006Z
5U1065Z
5U1066Z
5U1113Z
15
10
15
31
THE FRONT AND REAR ACTUATOR MOUNTS 3A10004P (3) AND 3A10005P (4)
AND RELATED FIXINGS ARE TO BE LOOSELY ATTACHED TO THE BASE.
THESE BRACKETS WILL THEN BE CORRECTLY POSITIONED AND
SECURED IN THE CORRECT ORIENTATION DURING THE CREATION
OF THE TOP LEVEL PRODUCT
8
UL
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2008
DRAWN
G Mullenger
CAD NO
2R11002Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
23/03/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Streamline Large Wheel Base
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
3
4
DATE
3/06 1/07 4/07 11/07
DCN
1198 1234 1243 1268
ASSEMBLY
2R11002Z
ISSUE
4
UNCONTROLLED WHEN PRINTED
2
16
30
14
30
16
14
25
25
17
30
20
30
17
20
UPPER CROSS
SECTION A-A
6
25
LOWER CROSS
SECTION B-B
3
4
3
30
25
7
30
21
30
30
21
STREAMLINE LIFTING MECHANISM
32
ENSURE THAT THE LINK BAR
IS POSITIONED ON THE CASTOR
SIDE OF THE LINKING LUG TO
REMOVE ANY INTERFERENCE
WITH THE H SECTION NUT CAP
2
REFER TO UPPER
H FRAME CROSS
SECTION A-A
6
STREAMLINE LARGE WHEEL
PEDAL MECHANISM
31
11
8
7
32
ITEM QTY
1
2
2
2
3
2
4
1
5
1
6
1
7
1
8
1
9
1
10
1
11
3
4
12
13
2
14
4
15
6
16
4
17
4
18
2
19
4
20
4
21
4
22
12
23
2
24
2
25
8
26
4
4
27
28
2
29
16
30
16
31
2
32
2
33
1
34
1
35
1
36
1
PART No.
3A03263Z
3A10002P
3A10003P
3A10004P
3A10005P
3A10010P
3A10011P
3A10014R
3A10018R
5H1204F
5H1212F
5J7655C
5J7658N
5J8074A
5L0362V
5L0707L
5L0906Z
5L2919C
5L2955K
5L3319B
5L3319C
5L3362K
5L3503Z
5M0408C
5N0057X
5N1107E
5N1125L
5N3744Z
5N3944Z
5P8000Z
5T0028Z
5T3200Z
5U1006Z
5U1065Z
5U1066Z
5U1113Z
ISSUE No.
0
0
2
0
0
2
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
3
1
1
0
DESCRIPTION
Linking Lug
H Section
H Section Link
Front Actuator Mounting Bracket
Rear Actuator Mount
Large Wheel Base Frame
Link Bar
Extended Hexagonal Bar
Hexagonal Bar
2044XSX125R36-32S30 Direcl Castor
2046UAP125R36-32S30 Locking Castor
M6x10 Capped Allen Screw
M6x20 Hex Set Screw
M10x100mm Hex Bolt
1/4 Flat Washer
3/4 Grey End Cap
3/4 Open Starlock
M6 Nyloc Nut
M6 Shakeproof Washer
M10 Benton Lock Nut Z/P
M10 Nyloc Nut
M10 Washer Flat Form B
12mm Starlock Capped
1/4"x1" Seloc Pin
M10 White Nut Cap
1 1/2"x3/4"x16G Grey Insert
1 1/2 x 10G Grey End Cap
40x40x2.5 Grey Insert
50x25x2.5 Grey Insert
Bronze Flanged Bush
Nylon Foot Rubber
Pedal Rubber
Huntleigh Akron Label
Pedal Sticker
Pedal Sticker
Streamline 225 Product Label
1
SHEET 2 OF 2
31
10
ENSURE THAT THE DIRECTIONAL CASTOR
IS POSITIONED AT THE PEDAL END OF THE BASE
AND SHOULD BE INDICATED BY USING THE RED
STICKER 5U1095Z
32
31
2
1
IT IS IMPORTANT TO ENSURE THE FLAT
SECTION ON THE WHEEL LINK BAR IS
POSITIONED AS SHOWN AT THE RAM
END OF THE BASE
IMPORTANT
WHEN FITTING THE LINK BARS 3A10003P
ENSURE THAT THE THREE HOLES
ARE POSITIONED AWAY FROM THE
RAM END OF THE BASE FRAME
CASTORS SECURED USING
M6x10 CAP HEAD SCREW AND
WASHER ON INSIDE FACE
UL
C
REFER TOO LOWER LINK BAR
CROSS SECTION B-B
7
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2008
DRAWN
G Mullenger
CAD NO
2R11002Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
23/03/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Streamline Large Wheel Base
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
3
4
DATE
3/06 1/07 4/07 11/07
DCN
1198 1234 1243 1268
ASSEMBLY
2R11002Z
ISSUE
4
ITEM QTY
1
2
2
1
3
1
4
1
5
2
6
1
7
2
8
4
4
9
10
6
11
4
12
2
13
4
14
8
15
2
16
4
17
4
18
2
19
8
20
2
21
8
22
4
23
1
PART No.
3A03249Z
3A03682C
3A10054P
3A10057P
3A10068R
3A10069R
5J7662A
5J8065A
5K1238U
5K1241U
5L0362V
5L2919C
5L3319C
5L3362K
5M0300R
5M3145S
5N0057X
5N0909E
5N2100M
5N2300M
5N3944Z
5P8000Z
5T8800Z
ISSUE No.
0
2
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Double Grooved Hinge Pin (10x84)
Sliding Debris Tray Holder
Streamline Entry Level Frame
Powered/Manual Backrest Frame
Gynae Guard Spacer
Streamline Gynae ABS Guard
M6x40 Hex Ht Bolt
M10x55mm Hex Bolt
M6x25 Pan Head Set Screw
M6x40 Pan Head Set Screw
1/4 Flat Washer
M6 Nyloc Nut
M10 Nyloc Nut
M10 Washer Flat Form B
1/4 R Clip
8mm E Clip
M10 White Nut Cap
1 x1 x 16G Insert
8.5mm Grey Insert
11mm Grey Insert
50x25x2.5 Grey Insert
Bronze Flanged Bush
100mm Debris Tray
UNCONTROLLED WHEN PRINTED
10
19
10
19
4
1
10
16
16
17
21
20
18
10
14
18
10
22
13
14
8
19
19
19
9
16
10
19
21
3
1
8
16
14
22
9
14
13
17
21
12
20
21
9
21
11
15
2
5
19
8
11
7
9
14
15
19
22
6
14
21
23
13
17
17
12
11
14
13
8
14
22
5
11
7
C
SHEET 1 OF 2
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11107Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
13/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Streamline Entry Level Gynae Top Assembly
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
08/07 2/08
DCN
1256 1278
ASSEMBLY
2R11107Z
ISSUE
2
UNCONTROLLED WHEN PRINTED
3
3
8
8
13
13
258
ITEM QTY
1
2
2
1
3
1
4
1
5
2
6
1
7
2
8
4
4
9
10
6
11
4
12
2
13
4
14
8
15
2
16
4
17
4
18
2
19
8
20
2
21
8
22
4
23
1
PART No.
3A03249Z
3A03682C
3A10054P
3A10057P
3A10068R
3A10069R
5J7662A
5J8065A
5K1238U
5K1241U
5L0362V
5L2919C
5L3319C
5L3362K
5M0300R
5M3145S
5N0057X
5N0909E
5N2100M
5N2300M
5N3944Z
5P8000Z
5T8800Z
ISSUE No.
0
2
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Double Grooved Hinge Pin (10x84)
Sliding Debris Tray Holder
Streamline Entry Level Frame
Powered/Manual Backrest Frame
Gynae Guard Spacer
Streamline Gynae ABS Guard
M6x40 Hex Ht Bolt
M10x55mm Hex Bolt
M6x25 Pan Head Set Screw
M6x40 Pan Head Set Screw
1/4 Flat Washer
M6 Nyloc Nut
M10 Nyloc Nut
M10 Washer Flat Form B
1/4 R Clip
8mm E Clip
M10 White Nut Cap
1 x1 x 16G Insert
8.5mm Grey Insert
11mm Grey Insert
50x25x2.5 Grey Insert
Bronze Flanged Bush
100mm Debris Tray
STREAMLINE ENTRY LEVEL BACKREST FIXINGS
ENTRY LEVEL
BACKREST END
13
8
3
ENTRY LEVEL
FOOT FRAME END
13
176
3
8
STREAMLINE ENTRY LEVEL FOOT END FIXINGS
C
SHEET 2 OF 2
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11107Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
13/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Streamline Entry Level Gynae Top Assembly
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
08/07 2/08
DCN
1256 1278
ASSEMBLY
2R11107Z
ISSUE
2
SHEET 1 OF 2
UNCONTROLLED WHEN PRINTED
17
14
14
9
6
13
7
11
17
23
23
14
6
20
2
5
13
19
14
13
26
21
20
29
25
21
1
24
9
18
13
25
25
26
21
23
19
25
22
1
12
13
23
26
21
23
22
18
23
19
26
25
13
25
3
4
22
25
24
25
5T8800Z
5T0400Z
5T0300Z
5P8000Z
5N3944Z
5N2300M
5N2100M
5N0057X
5M3145S
5M0300R
5L3362K
5L3319C
5L2919C
5L0906Z
5L0707L
5L0362V
5K1241U
5K1238U
5J8073A
5J8065A
5J7662A
3A10085R
3A10069R
3A10068R
3A10057P
3A10056P
3A10055P
3A03682C
3A03249Z
PART No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
2
0
ISSUE No.
100mm Debris Tray
200mm Self Adhesive Loop Velcro
200mm Self Adhesive Hook Velcro
Bronze Flanged Bush
50x25x2.5 Grey Insert
11mm Grey Insert
8.5mm Grey Insert
M10 White Nut Cap
8mm E Clip
1/4 R Clip
M10 Washer Flat Form B
M10 Nyloc Nut
M6 Nyloc Nut
3/4 Open Starlock
3/4 Grey End Cap
1/4 Flat Washer
M6x40 Pan Head Set Screw
M6x25 Pan Head Set Screw
M10x95mm Hex Bolt
M10x55mm Hex Bolt
M6x40 Hex Ht Bolt
Gynae Top Frame Cover Shroud
Streamline Gynae ABS Guard
Gynae Guard Spacer
Powered/Manual Backrest Frame
Tilting Main Frame
Tilt Top Frame
Sliding Debris Tray Holder
Double Grooved Hinge Pin (10x84)
DESCRIPTION
19
11
12
29
1
28
2
27
2
26
8
25
12
24
2
23
8
22
6
21
4
20
2
19
14
18
6
17
2
16
2
15
2
14
4
13
6
12
4
11
2
10
4
9
2
8
1
7
1
6
2
5
1
4
1
3
1
2
1
1
2
ITEM QTY
25
18
19
12
23
26
23
25
25
25
19
10
10
28
12
19
10
26
26
27
19
19
27
28
18
22
19
19
15
18
19
22
22
8
19
18
10
19
26
16
C
16
15
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11108Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
07/09/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Streamline Gynae 3 Tilt Level Top Assembly
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
9/07 2/08
DCN
1256 1278
ASSEMBLY
2R11108Z
ISSUE
2
ITEM QTY
1
2
2
1
3
1
4
1
5
1
6
2
7
1
8
1
9
2
10
4
11
2
12
4
13
6
4
14
15
2
16
2
17
2
18
6
19
14
20
2
21
4
22
6
23
8
24
2
25
12
26
8
27
2
28
2
29
1
SHEET 2 OF 2
8
H SECTION
15
4
10
16
19
22
18
19
26
4
H SECTION
FRONT MAIN FRAME SECTION
FIXING DETAILS
15
22
ISSUE No.
0
2
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Double Grooved Hinge Pin (10x84)
Sliding Debris Tray Holder
Tilt Top Frame
Tilting Main Frame
Powered/Manual Backrest Frame
Gynae Guard Spacer
Streamline Gynae ABS Guard
Gynae Top Frame Cover Shroud
M6x40 Hex Ht Bolt
M10x55mm Hex Bolt
M10x95mm Hex Bolt
M6x25 Pan Head Set Screw
M6x40 Pan Head Set Screw
1/4 Flat Washer
3/4 Grey End Cap
3/4 Open Starlock
M6 Nyloc Nut
M10 Nyloc Nut
M10 Washer Flat Form B
1/4 R Clip
8mm E Clip
M10 White Nut Cap
8.5mm Grey Insert
11mm Grey Insert
50x25x2.5 Grey Insert
Bronze Flanged Bush
200mm Self Adhesive Hook Velcro
200mm Self Adhesive Loop Velcro
100mm Debris Tray
22
H SECTION
18
PART No.
3A03249Z
3A03682C
3A10055P
3A10056P
3A10057P
3A10068R
3A10069R
3A10085R
5J7662A
5J8065A
5J8073A
5K1238U
5K1241U
5L0362V
5L0707L
5L0906Z
5L2919C
5L3319C
5L3362K
5M0300R
5M3145S
5N0057X
5N2100M
5N2300M
5N3944Z
5P8000Z
5T0300Z
5T0400Z
5T8800Z
4
18
19
19
26
18
26
10
10
19
19
16
26
H SECTION
22
19
4
19
11
REAR MAIN FRAME SECTION
FIXING DETAILS
3
10
26
19
26
22
18
TILT FRAME PIVOT SECTION
FIXING DETAILS
19
C
UNCONTROLLED WHEN PRINTED
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11108Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
07/09/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Streamline Gynae 3 Tilt Level Top Assembly
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
9/07 2/08
DCN
1256 1278
ASSEMBLY
2R11108Z
ISSUE
2
ITEM QTY
1
1
2
1
3
1
4
2
5
1
6
4
7
2
8
2
9
1
10
2
11
6
12
2
13
1
14
2
13
9
10
PART No.
3A09040Z
3A10061P
5G2700Z
5J7665A
5J8266A
5L0362V
5L0803Z
5L2919C
5L3519C
5L3562K
5L3577X
5N0055X
5N0058X
5N0300L
ISSUE No.
1
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Trunnion
Release Bar Assembly
400N Locking Gas Strut
M6x55 Bolt Hex Ht
M12x60mm Hex Bolt
1/4 Flat Washer
5/8 Capped Starlock
M6 Nyloc Nut
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M6 White Nut Cap
M12 White Nut Cap
3/8 End Cap
11
11
11
3
11
14
11
7
11
12
8
10
1
6
5
7
12
8
6
6
4
6
2
4
14
C
UNCONTROLLED WHEN PRINTED
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11224Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
16/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Manual Backrest Module
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
ISSUE
1
DATE
8/07
DCN
1253
ASSEMBLY
2R11224Z
ISSUE
1
UNCONTROLLED WHEN PRINTED
HYDRAULIC
5
14
5
8
15
14
8
3A10004P. FRONT ACTUATOR
MOUNTING BARCKET
6
7
16
8
10
3
12
1
7
1
12
10
9
11
13
16
4
15
13
9
10
UL
10
11
12
16
2
15
2
14
2
13
2
12
6
11
2
10
10
9
2
8
12
7
6
6
2
5
6
4
1
3
1
2
1
1
2
ITEM QTY
7
8
8
5
12
10
7
2
10
8
6
8
5
3A10005P. REAR
ACTUATOR MOUNT
C
SHEET 1 OF 2
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2008
DRAWN
GMullenger
CAD NO
2R11201Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
05/09/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Streamline Hydraulic Ram Kit
5U1066Z
5T3200Z
5N2100M
5N0058X
5N0056X
5M3161E
5L3562K
5L3519C
5L3162K
5L3119C
5J8270A
5J7866A
5F7500Z
3A10036P
3A10035P
3A10019R
PART No.
1
0
0
0
0
0
0
0
0
0
0
0
0
5
0
0
ISSUE No.
Patient Positioning Solutions
Pedal Sticker
Pedal Rubber
8.5mm Grey Insert
M12 White Nut Cap
M8 White Nut Cap
8x30 Spirol Pin
M12 Washer Flat Form B
M12 Nyloc Nut
M8 Washer Flat Form B
M8 Nyloc Nut
M12x80mm Hex Bolt
M8x60 Hex Ht Bolt
Power Packer DSC0101-08-110/1
Streamline Hydraulic Right Foot Lever
Streamline Hydraulic Left Foot Lever
10mm Spacer Tube
DESCRIPTION
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
9/06 11/07
DCN
1198 1268
ASSEMBLY
2R11201Z
ISSUE
2
HYDRAULIC
UNCONTROLLED WHEN PRINTED
IMPORTANT.
ENSURE THAT THE FRONT ACTUATOR
MOUNT ATTACHED TO THE BASE ASSEMBLY
IS POSITIONED IN THE FIRST TWO HOLES
TOWARDS THE PUMP END OF THE BASE
TO ENSURE CORRECT STROKE IS ACHIEVED
ON THE HYDRAULIC PUMP
IMPORTANT.
ENSURE THAT 6 OFF M12 WASHERS
ARE PLACED EITHER SIDE OF THE
PUMP TO SECURE THE MECHANISM
AND REMOVE ANY LATERIAL MOVEMENT
IMPORTANT.
WHEN REPLACING OR INSTALLING THE
HYDRAULIC PUMP ENSURE THAT THE ROD
END OF THE PUMP IS BOLTED TO THE
MOUNTING BRACKET 3A10004P BEFORE
THE BRACKET IS RAISED INTO POSITION
AND SECURED TO THE UNDERSIDE OF THE
LINK BARS.
IMPORTANT.
ENSURE THAT THE REAR ACTUATOR MOUNT
3A10005P ATTACHED TO THE BASE FRAME
IS INSTALLED IN THE CORRECT LOWER
POSITION AND ORIENTATION.
UL
SHEET 2 OF 2
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2008
DRAWN
GMullenger
CAD NO
2R11201Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
05/09/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Streamline Hydraulic Ram Kit
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
9/06 11/07
DCN
1198 1268
ASSEMBLY
2R11201Z
ISSUE
2
HANNING 230V
2
3A10004P FRONT ACTUATOR
MOUNTING BARCKET
9
3A10005P REAR ACTUATOR
MOUNTING BRACKET
6
2
7
5
5
2
2
10
5
5
5
1
4
8
7
5
3
4
10
5
5
4
8
8
4
11
14
8
12
11
12
9
6
7
UNCONTROLLED WHEN PRINTED
2Z1100Z HANNING MAINS
CABLE AND RAM PLUG
RUBBER
13
7
3
14
1
13
1
12
2
11
2
10
2
9
2
8
6
7
4
6
2
5
12
4
6
3
2
2
6
1
1
ITEM QTY
S6243
5S0326Z
5S0315Z
5S0307Z
5N2100M
5N0058X
5N0056X
5L3562K
5L3519C
5L3162K
5L3119C
5J8264A
5J7866A
5F0601Z
PART No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ISSUE No.
Cable Gland (Bell End Split)
Curly Wrap RS227-974
Cable Tie RS543-428
Cable Tie Base RS227-996
8.5mm Grey Insert
M12 White Nut Cap
M8 White Nut Cap
M12 Washer Flat Form B
M12 Nyloc Nut
M8 Washer Flat Form B
M8 Nyloc Nut
M12x50mm Hex Bolt
M8x60 Hex Ht Bolt
230v Hanning Ram (Type V)
DESCRIPTION
SHEET 1 OF 2
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11202Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
06/09/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Posit ioning Solutions
230v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 1/07
DCN
1198 1234
ASSEMBLY
2R11202Z
ISSUE
2
HANNING 230V
IMPORTANT.
ENSURE THAT THE REAR ACTUATOR MOUNT
3A10004P ATTACHED TO THE BASE FRAME
IS INSTALLED IN THE CORRECT UPPER
POSITION AND ORIENTATION FOR
INSTALLATION OF HANNING RAM
ENSURE MAINS LEAD PASSES THROUGH
AND IS SECURED BY THE CABLE GLAND
TO REMOVE ANY STRAIN RELIEF ON THE
MAINS CABLE
ENSURE CURLY WRAP IS
POSITIONED HIGH ENOUGH
TO CLEAR THE LINK BARS
WHEN IN OPERATION
ALL ACTUATOR RAM BRACKETS
WILL BE REFERENCED TO THE RETRACTABLE
AND LARGE WHEEL BASE ASSEMBLIES TO
WHICH THESE PARTS WILL BE ATTACHED.
ENSURE HANNING AIR PIPE TO
HAND/FOOTSWITCH IS SECURED
AND FOLLOWS THE MAINS LEAD
THROUGH THE CURLY WRAP
IMPORTANT.
WHEN REPLACING OR INSTALLING THE
ACTUATOR ENSURE THAT THE ROD
END OF THE RAM IS BOLTED TO THE
MOUNTING BRACKET 3A10004P BEFORE
THE BRACKET IS RAISED INTO POSITION
AND SECURED TO THE UNDERSIDE OF THE
LINK BARS.
IMPORTANT.
ENSURE THAT THE FRONT ACTUATOR
MOUNT ATTACHED TO THE BASE ASSEMBLY
IS POSITIONED IN THE FIRST TWO HOLES
TOWARDS THE PUMP END OF THE BASE
TO ENSURE CORRECT STROKE IS ACHIEVED
ON THE ACTUATOR
IMPORTANT
ENSURE THAT THE HANNING RAM
IS INSTALLED TO THE RIGHT HAND
PLATE OF THE REAR ACTUATOR
MOUNTING BRACKET
UNCONTROLLED WHEN PRINTED
C
SHEET 2 OF 2
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11202Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
06/09/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Posit ioning Solutions
230v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 1/07
DCN
1198 1234
ASSEMBLY
2R11202Z
ISSUE
2
HANNING 115V
2
3A10004P FRONT ACTUATOR
MOUNTING BARCKET
9
3A10005P REAR ACTUATOR
MOUNTING BRACKET
6
2
7
5
5
2
2
10
5
5
5
1
4
8
7
5
3
4
10
5
5
4
8
8
4
11
14
8
12
11
12
9
6
7
UNCONTROLLED WHEN PRINTED
2Z1100Z HANNING MAINS
CABLE AND RAM PLUG
RUBBER
13
7
3
14
1
13
1
12
2
11
2
10
2
9
2
8
6
7
4
6
2
5
12
4
6
3
2
2
6
1
1
ITEM QTY
S6243
5S0326Z
5S0315Z
5S0307Z
5N2100M
5N0058X
5N0056X
5L3562K
5L3519C
5L3162K
5L3119C
5J8264A
5J7866A
5F0502Z
PART No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ISSUE No.
Cable Gland (Bell End Split)
Curly Wrap RS227-974
Cable Tie RS543-428
Cable Tie Base RS227-996
8.5mm Grey Insert
M12 White Nut Cap
M8 White Nut Cap
M12 Washer Flat Form B
M12 Nyloc Nut
M8 Washer Flat Form B
M8 Nyloc Nut
M12x50mm Hex Bolt
M8x60 Hex Ht Bolt
115v Hanning Ram (Type V)
DESCRIPTION
SHEET 1 OF 2
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11203Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
06/09/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Posit ioning Solutions
115v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 01/07
DCN
1198 1234
ASSEMBLY
2R11203Z
ISSUE
2
HANNING 115V
IMPORTANT.
ENSURE THAT THE REAR ACTUATOR MOUNT
3A10004P ATTACHED TO THE BASE FRAME
IS INSTALLED IN THE CORRECT UPPER
POSITION AND ORIENTATION FOR
INSTALLATION OF HANNING RAM
ENSURE MAINS LEAD PASSES THROUGH
AND IS SECURED BY THE CABLE GLAND
TO REMOVE ANY STRAIN RELIEF ON THE
MAINS CABLE
ENSURE CURLY WRAP IS
POSITIONED HIGH ENOUGH
TO CLEAR THE LINK BARS
WHEN IN OPERATION
ALL ACTUATOR RAM BRACKETS
WILL BE REFERENCED TO THE RETRACTABLE
AND LARGE WHEEL BASE ASSEMBLIES TO
WHICH THESE PARTS WILL BE ATTACHED.
ENSURE HANNING AIR PIPE TO
HAND/FOOTSWITCH IS SECURED
AND FOLLOWS THE MAINS LEAD
THROUGH THE CURLY WRAP
IMPORTANT.
WHEN REPLACING OR INSTALLING THE
ACTUATOR ENSURE THAT THE ROD
END OF THE RAM IS BOLTED TO THE
MOUNTING BRACKET 3A10004P BEFORE
THE BRACKET IS RAISED INTO POSITION
AND SECURED TO THE UNDERSIDE OF THE
LINK BARS.
IMPORTANT.
ENSURE THAT THE FRONT ACTUATOR
MOUNT ATTACHED TO THE BASE ASSEMBLY
IS POSITIONED IN THE FIRST TWO HOLES
TOWARDS THE PUMP END OF THE BASE
TO ENSURE CORRECT STROKE IS ACHIEVED
ON THE ACTUATOR
IMPORTANT
ENSURE THAT THE HANNING RAM
IS INSTALLED TO THE RIGHT HAND
PLATE OF THE REAR ACTUATOR
MOUNTING BRACKET
UNCONTROLLED WHEN PRINTED
C
SHEET 2 OF 2
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11203Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
06/09/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Posit ioning Solutions
115v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 01/07
DCN
1198 1234
ASSEMBLY
2R11203Z
ISSUE
2
HANNING 100V
2
3A10004P FRONT ACTUATOR
MOUNTING BARCKET
9
3A10005P REAR ACTUATOR
MOUNTING BRACKET
6
2
7
5
5
2
2
10
5
5
5
1
4
8
7
5
3
4
10
5
5
4
8
8
4
11
14
8
12
11
12
9
6
7
UNCONTROLLED WHEN PRINTED
2Z1100Z HANNING MAINS
CABLE AND RAM PLUG
RUBBER
13
7
3
14
1
13
1
12
2
11
2
10
2
9
2
8
6
7
4
6
2
5
12
4
6
3
2
2
6
1
1
ITEM QTY
S6243
5S0326Z
5S0315Z
5S0307Z
5N2100M
5N0058X
5N0056X
5L3562K
5L3519C
5L3162K
5L3119C
5J8264A
5J7866A
5F1211Z
PART No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ISSUE No.
Cable Gland (Bell End Split)
Curly Wrap RS227-974
Cable Tie RS543-428
Cable Tie Base RS227-996
8.5mm Grey Insert
M12 White Nut Cap
M8 White Nut Cap
M12 Washer Flat Form B
M12 Nyloc Nut
M8 Washer Flat Form B
M8 Nyloc Nut
M12x50mm Hex Bolt
M8x60 Hex Ht Bolt
100v Hanning Ram (Type V)
DESCRIPTION
SHEET 1 OF 2
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11212Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
06/09/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Posit ioning Solutions
100v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 01/07
DCN
1198 1234
ASSEMBLY
2R11212Z
ISSUE
2
HANNING 100V
IMPORTANT.
ENSURE THAT THE REAR ACTUATOR MOUNT
3A10004P ATTACHED TO THE BASE FRAME
IS INSTALLED IN THE CORRECT UPPER
POSITION AND ORIENTATION FOR
INSTALLATION OF HANNING RAM
ENSURE MAINS LEAD PASSES THROUGH
AND IS SECURED BY THE CABLE GLAND
TO REMOVE ANY STRAIN RELIEF ON THE
MAINS CABLE
ENSURE CURLY WRAP IS
POSITIONED HIGH ENOUGH
TO CLEAR THE LINK BARS
WHEN IN OPERATION
ALL ACTUATOR RAM BRACKETS
WILL BE REFERENCED TO THE RETRACTABLE
AND LARGE WHEEL BASE ASSEMBLIES TO
WHICH THESE PARTS WILL BE ATTACHED.
ENSURE HANNING AIR PIPE TO
HAND/FOOTSWITCH IS SECURED
AND FOLLOWS THE MAINS LEAD
THROUGH THE CURLY WRAP
IMPORTANT.
WHEN REPLACING OR INSTALLING THE
ACTUATOR ENSURE THAT THE ROD
END OF THE RAM IS BOLTED TO THE
MOUNTING BRACKET 3A10004P BEFORE
THE BRACKET IS RAISED INTO POSITION
AND SECURED TO THE UNDERSIDE OF THE
LINK BARS.
IMPORTANT.
ENSURE THAT THE FRONT ACTUATOR
MOUNT ATTACHED TO THE BASE ASSEMBLY
IS POSITIONED IN THE FIRST TWO HOLES
TOWARDS THE PUMP END OF THE BASE
TO ENSURE CORRECT STROKE IS ACHIEVED
ON THE ACTUATOR
IMPORTANT
ENSURE THAT THE HANNING RAM
IS INSTALLED TO THE RIGHT HAND
PLATE OF THE REAR ACTUATOR
MOUNTING BRACKET
UNCONTROLLED WHEN PRINTED
C
SHEET 2 OF 2
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2006
DRAWN
GMullenger
CAD NO
2R11212Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
06/09/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Posit ioning Solutions
100v Single Streamline Hanning Ram Kit
1 FARTHI NG ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www. huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
09/06 01/07
DCN
1198 1234
ASSEMBLY
2R11212Z
ISSUE
2
ITEM QTY
1
1
2
3
3
4
4
1
PART No.
2Z5000Z
5K0407X
5L2855K
5U1121Z
ISSUE No.
2
0
0
0
DESCRIPTION
A1048 Streamline UL Junction Box
No10x1/2 Pan Head Set Screw
5mm Shakeproof Washer
Earth Label
1
4
3
30
2
3
3
2
45
53
UL
UNCONTROLLED WHEN PRINTED
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11210Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
23/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Streamline UL Junction Box Positioning
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
3
DATE
01/07 07/07 01/08
DCN
1198 1253 1268
ASSEMBLY
2R11210Z
ISSUE
3
230V EU LINAK E/B
UNCONTROLLED WHEN PRINTED
8
28
8
31
19
3A10004P FRONT ACTUATOR
MOUNTING BRACKET
9
32
28
21
34
19
29
18
CURLY WRAP
CUT LENGTH 130mm
29
19
25
18
CURLY WRAP
CUT LENGTH 130mm
34
25
34
21
20
26
7
CURLY WRAP
CUT LENGTH 130mm
33
41
23
11
23
33
23
13
23
23
22
23
24
42
27
CONTROL BOX CABLE 5F0651Z FROM BACKREST
ACTUATOR TO BE PLUGGED INTO SOCKET 1 OF
CONTROL BOX AND SECURED ON UNDERSIDE OF
H SECTION
24
24
13
6
24
23
23
23
23
8
19
8
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
18
24
25
24
3A10005P REAR ACTUATOR
MOUNTING BRACKET
23
19
C
24
22
18
24
27
25
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01069 230V EU Power Unit
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x60mm Hex Bolt
M10x65mm Hex Bolt
M12x50mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M10 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel (0.15m)
Cable Ducting Channel (0.18m)
Cable Tie RS543-428
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box cable
912100 EU Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
225Kg Load Warning Label
Earth Label
Cable Gland (Bell End Split)
0821008 CU20 Blanking Plug
35
19
19
SHEET 1 OF 2
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0952Z
5F0955Z
5F0956Z
5J7866A
5J8066A
5J8067A
5J8264A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0057X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0306Z
5S0315Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0652Z
5S0655Z
5S0656Z
5U1116Z
5U1121Z
S6243
S9108
CURLY CONTROL BOX CABLE 5F0650Z FROM
BASE ACTUATOR TO BE PLUGGED INTO
SOCKET 2 OF CONTROL BOX AND SECURED
ALONG LINK BARS USING CABLE TIES
22
27
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
6
9
1
10
1
11
1
12
1
13
2
14
1
15
8
16
2
17
8
18
6
19
12
20
2
21
4
22
4
23
14
24
8
25
6
26
2
27
3
28
2
29
4
30
1
32
1
31
1
33
2
34
3
35
1
36
1
37
1
38
1
39
1
40
2
41
2
42
1
43
1
44
1
45
1
23
41
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
LARGE CURLY WRAP
CUT LENGTH 130mm
DRAWN
GMullenger
CAD NO
2R11225Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
30/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Linak 230v EU Electric Backrest Ram Kit
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
7/07 10/07
DCN
1253 1256
ASSEMBLY
2R11225Z
ISSUE
2
230V EU LINAK E/B
4
15
406
90
5
5S0216Z
EARTH
CABLE
CONTROL BRACKET HOLE POSITIONS
5S0652Z
EU MAINS
CABLE
40
14
POWER
SOCKET
16
43
40
2
16
45
15
15
17
SOCKET 2
CURLY CONTROL BOX CABLE 5F0650Z
TO BE PLUGGED INTO BASE ACTUATOR
AND SECURED ALONG LINK BARS USING
CABLE TIES
17
15
17
15
3
44
17
1
EARTH CABLE CONNECTION TO BE FITTED
ON UNDERSIDE OF BASE SIDE MEMBER
UNDER CONTROL BOX BRACKET
SOCKET 1
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO BACKREST ACTUATOR
AND SECURED ALONG UNDERSIDE OF
H SECTION
MAINS CABLE TO PASS THROUGH CABLE
GLAND TO CREATE STRAIN RELIEF ON THE
MAINS CABLE
C
SHEET 2 OF 2
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
6
9
1
10
1
11
1
12
1
13
2
14
1
15
8
16
2
17
8
18
6
19
12
20
2
21
4
22
4
23
14
24
8
25
6
26
2
27
3
28
2
29
4
30
1
32
1
31
1
33
2
34
3
35
1
36
1
37
1
38
1
39
1
40
2
41
2
42
1
43
1
44
1
45
1
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01069 230V EU Power Unit
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x60mm Hex Bolt
M10x65mm Hex Bolt
M12x50mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M10 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel (0.15m)
Cable Ducting Channel (0.18m)
Cable Tie RS543-428
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box cable
912100 EU Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
225Kg Load Warning Label
Earth Label
Cable Gland (Bell End Split)
0821008 CU20 Blanking Plug
UNCONTROLLED WHEN PRINTED
DRAWN
GMullenger
CAD NO
2R11225Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
30/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0952Z
5F0955Z
5F0956Z
5J7866A
5J8066A
5J8067A
5J8264A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0057X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0306Z
5S0315Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0652Z
5S0655Z
5S0656Z
5U1116Z
5U1121Z
S6243
S9108
Patient Positioning Solutions
Linak 230v EU Electric Backrest Ram Kit
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
7/07 10/07
DCN
1253 1256
ASSEMBLY
2R11225Z
ISSUE
2
120V EU LINAK E/B
UNCONTROLLED WHEN PRINTED
8
32
28
8
19
CURLY WRAP
31
CUT LENGTH 130mm
3A10004P FRONT ACTUATOR
MOUNTING BRACKET
9
28
21
34
29
19
CURLY WRAP
CUT LENGTH 130mm
19
18
18
25
CURLY WRAP
CUT LENGTH 130mm
25
29
34
21
20
34
26
41
CURLY WRAP
CUT LENGTH 130mm
7
33
23
11
23
33
23
13
23
23
22
23
24
42
27
CONTROL BOX CABLE 5F0651Z FROM BACKREST
ACTUATOR TO BE PLUGGED INTO SOCKET 2 OF
CONTROL BOX AND SECURED ON UNDERSIDE OF
H SECTION
24
24
13
6
24
23
23
23
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01169 120V US Power Unit
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x60mm Hex Bolt
M10x65mm Hex Bolt
M12x50mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M10 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel (0.15m)
Cable Ducting Channel (0.18m)
Cable Tie RS543-428
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box cable
912100 EU Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
225Kg Load Warning Label
Earth Label
Cable Gland (Bell End Split)
0821008 CU20 Blanking Plug
CURLY CONTROL BOX CABLE 5F0650Z FROM
BASE ACTUATOR TO BE PLUGGED INTO
SOCKET 1 OF CONTROL BOX AND SECURED
ALONG LINK BARS USING CABLE TIES
22
19
8
19
19
18
24
25
LARGE CURLY WRAP
CUT LENGTH 130mm
41
35
24
3A10005P REAR ACTUATOR
MOUNTING BRACKET
23
19
24
22
18
SHEET 1 OF 2
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0953Z
5F0955Z
5F0956Z
5J7866A
5J8066A
5J8067A
5J8264A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0057X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0306Z
5S0315Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0652Z
5S0655Z
5S0656Z
5U1116Z
5U1121Z
S6243
S9108
23
8
27
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
6
9
1
10
1
11
1
12
1
13
2
14
1
15
8
16
2
17
8
18
6
19
12
20
2
21
4
22
4
23
14
24
8
25
6
26
2
27
3
28
2
29
4
30
1
32
1
31
1
33
2
34
3
35
1
36
1
37
1
38
1
39
1
40
2
41
2
42
1
43
1
44
1
45
1
24
27
25
23
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11226Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
30/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Linak 120v EU Electric Backrest Ram Kit
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
7/07 10/07
DCN
1253 1256
ASSEMBLY
2R11226Z
ISSUE
2
120V EU LINAK E/B
15
406
90
4
5
CONTROL BRACKET HOLE POSITIONS
5S0216Z
EARTH
CABLE
5S0652Z
EU MAINS
CABLE
40
14
POWER
SOCKET
16
40
2
16
43
45
15
SOCKET 2
CURLY CONTROL BOX CABLE 5F0650Z
TO BE PLUGGED INTO BASE ACTUATOR
AND SECURED ALONG LINK BARS USING
CABLE TIES
15
17
17
15
17
SOCKET 1
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO BACKREST ACTUATOR
AND SECURED ALONG UNDERSIDE OF
H SECTION
15
3
44
17
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
6
9
1
10
1
11
1
12
1
13
2
14
1
15
8
16
2
17
8
18
6
19
12
20
2
21
4
22
4
23
14
24
8
25
6
26
2
27
3
28
2
29
4
30
1
32
1
31
1
33
2
34
3
35
1
36
1
37
1
38
1
39
1
40
2
41
2
42
1
43
1
44
1
45
1
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0953Z
5F0955Z
5F0956Z
5J7866A
5J8066A
5J8067A
5J8264A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0057X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0306Z
5S0315Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0652Z
5S0655Z
5S0656Z
5U1116Z
5U1121Z
S6243
S9108
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01169 120V US Power Unit
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x60mm Hex Bolt
M10x65mm Hex Bolt
M12x50mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M10 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel (0.15m)
Cable Ducting Channel (0.18m)
Cable Tie RS543-428
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box cable
912100 EU Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
225Kg Load Warning Label
Earth Label
Cable Gland (Bell End Split)
0821008 CU20 Blanking Plug
MAINS CABLE TO PASS THROUGH CABLE
GLAND TO CREATE STRAIN RELIEF ON
MAINS CABLE
1
EARTH CABLE CONNECTION TO BE FITTED
ON UNDERSIDE OF BASE SIDE MEMBER
UNDER CONTROL BOX BRACKET
C
SHEET 2 OF 2
UNCONTROLLED WHEN PRINTED
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11226Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
30/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Linak 120v EU Electric Backrest Ram Kit
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
7/07 10/07
DCN
1253 1256
ASSEMBLY
2R11226Z
ISSUE
2
UNCONTROLLED WHEN PRINTED
120V US LINAK E/B
8
28
8
19
31
3A10004P FRONT ACTUATOR
MOUNTING BRACKET
9
28
32
21
34
29
19
29
19
CURLY WRAP
CUT LENGTH 130mm
18
18
25
25
21
20
CURLY WRAP
CUT LENGTH 130mm
34
34
26
CURLY WRAP
CUT LENGTH 130mm
7
33
23
11
23
33
23
23
22
23
24
43
41
23
13
27
CONTROL BOX CABLE 5F0651Z FROM BACKREST
ACTUATOR TO BE PLUGGED INTO SOCKET 1 OF
CONTROL BOX AND SECURED ON UNDERSIDE OF
H SECTION
24
24
13
6
24
23
23
23
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
6
9
1
10
1
11
1
12
1
13
2
14
1
15
8
16
2
17
8
18
6
19
12
20
2
21
4
22
4
23
14
24
8
25
6
26
2
27
3
28
2
29
4
30
1
32
1
31
1
33
2
34
3
35
1
36
1
37
1
38
1
39
1
40
2
41
2
42
1
43
1
44
1
45
1
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01169 120V US Power Unit
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x60mm Hex Bolt
M10x65mm Hex Bolt
M12x50mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M10 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel (0.15m)
Cable Ducting Channel (0.18m)
Cable Tie RS543-428
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box cable
0912160 US Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
RS289-534 E Clip
225Kg Load Warning Label
Earth Label
0821008 CU20 Blanking Plug
23
8
CURLY CONTROL BOX CABLE 5F0650Z FROM
BASE ACTUATOR TO BE PLUGGED INTO
SOCKET 2 OF CONTROL BOX AND SECURED
ALONG LINK BARS USING CABLE TIES
22
19
27
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0953Z
5F0955Z
5F0956Z
5J7866A
5J8066A
5J8067A
5J8264A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0057X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0306Z
5S0315Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0653Z
5S0655Z
5S0656Z
5S0657Z
5U1116Z
5U1121Z
S9108
8
35
19
19
18
24
25
41
LARGE CURLY WRAP
CUT LENGTH 130mm
24
3A10005P REAR ACTUATOR
MOUNTING BRACKET
23
19
22
18
SHEET 1 OF 2
24
24
27
25
23
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11230Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
30/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Linak 120v US Electric Backrest Ram Kit
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
7/07 10/07
DCN
1253 1256
ASSEMBLY
2R11230Z
ISSUE
2
120V US LINAK E/B
406
90
15
4
5
CONTROL BRACKET HOLE POSITIONS
5S0216Z
EARTH
CABLE
5S0653Z
US MAINS
CABLE
40
14
POWER
SOCKET
16
40
2
16
44
45
15
15
17
SOCKET 2
CURLY CONTROL BOX CABLE 5F0650Z
TO BE PLUGGED INTO BASE ACTUATOR
AND SECURED ALONG LINK BARS USING
CABLE TIES
17
15
17
15
3
17
1
39
42
SOCKET 1
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO BACKREST ACTUATOR
AND SECURED ALONG UNDERSIDE OF
H SECTION
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
6
9
1
10
1
11
1
12
1
13
2
14
1
15
8
16
2
17
8
18
6
19
12
20
2
21
4
22
4
23
14
24
8
25
6
26
2
27
3
28
2
29
4
30
1
32
1
31
1
33
2
34
3
35
1
36
1
37
1
38
1
39
1
40
2
41
2
42
1
43
1
44
1
45
1
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0953Z
5F0955Z
5F0956Z
5J7866A
5J8066A
5J8067A
5J8264A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0057X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0306Z
5S0315Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0653Z
5S0655Z
5S0656Z
5S0657Z
5U1116Z
5U1121Z
S9108
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01169 120V US Power Unit
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x60mm Hex Bolt
M10x65mm Hex Bolt
M12x50mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M10 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel (0.15m)
Cable Ducting Channel (0.18m)
Cable Tie RS543-428
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box cable
0912160 US Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
RS289-534 E Clip
225Kg Load Warning Label
Earth Label
0821008 CU20 Blanking Plug
SHEET 2 OF 2
US MAINS CABLE STRAIN RELIEF TO BE
SECURED TO FIXING BRACKET USING 1 OFF
E CLIP 5S0657Z
EARTH CABLE CONNECTION TO BE FITTED
ON UNDERSIDE OF BASE SIDE MEMBER
UNDER CONTROL BOX BRACKET
UNCONTROLLED WHEN PRINTED
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
2R11230Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
30/07/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Linak 120v US Electric Backrest Ram Kit
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
7/07 10/07
DCN
1253 1256
ASSEMBLY
2R11230Z
ISSUE
2
230V EU LINAK TILT E/BACK
11
CHANNEL CUT
LENGTH 0.4M
29
CHANNEL CUT
LENGTH 0.1M
29
29
22
22
22
21
22
CONTROL BOX CABLE 5F0651Z FROM TILT
ACTUATOR TO BE PLUGGED INTO SOCKET 3 OF
CONTROL BOX AND ROUTED THROUGH DUCTING
CHANNEL ON MAIN FRAME/H SECTION
CHANNEL CUT
LENGTH 0.2M
25
11
6
22
CONTROL BOX CABLE 5F0651Z FROM BACKREST
ACTUATOR TO BE PLUGGED INTO SOCKET 1 OF
CONTROL BOX AND ROUTED THROUGH DUCTING
CHANNEL ON MAIN FRAME/H SECTION
22
37
37
22
22
21
20
8
10
25
12
20
19
22
23
22
9
18
22
37
18
26
3A10004P FRONT
ACTUATOR MOUNTING
BRACKET
18
26
22
7
18
17
29
24
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01069 230V EU Power Unit
LA317700+1015002P Actuator
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x65mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box Cable
912100 EU Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
225Kg Load Warning Label
Earth Label
Cable Gland (Bell End Split)
0821008 CU20 Blanking Plug
SHEET 1 OF 2
23
23
24
24
22
22
21
17
23
23
22
24
UNCONTROLLED WHEN PRINTED
17
18
9
22
18
21
22
25
18
23
38
18
3A10005P REAR
ACTUATOR MOUNTING
BRACKET
23
31
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0952Z
5F0954Z
5F0955Z
5F0956Z
5J7866A
5J8067A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0652Z
5S0655Z
5S0656Z
5U1116Z
5U1121Z
S6243
S9108
CURLY CONTROL BOX CABLE 5F0650Z FROM
BASE ACTUATOR TO BE PLUGGED INTO
SOCKET 2 OF CONTROL BOX
17
12
CURLY WRAP
LENGTH 0.13M
25
23
9
CHANNEL CUT
LENGTH 0.18M
21
22
22
27
30
11
22
25
27
CURLY WRAP
LENGTH 0.13M
29 CHANNEL CUT
LENGTH 0.2M
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
6
10
1
11
3
12
2
13
1
14
8
15
2
16
8
17
6
18
12
19
1
20
2
21
5
22
20
23
8
24
6
25
6
26
2
27
2
28
1
29
5
30
1
31
1
32
1
33
1
34
2
35
1
36
1
37
3
38
1
39
1
40
1
41
1
25
9
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
gary.mullenger
CAD NO
2R11234Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
22/10/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
Linak 230v EU Clinical Tilt & Electric Backrest Ram Kit
REVISION STATUS
ISSUE
1
DATE
10/07
DCN
1256
ASSEMBLY
2R11234Z
ISSUE
1
230V EU LINAK TILT E/BACK
406
90
15
4
5
5S0216Z
EARTH
CABLE
CONTROL BOX HOLE POSITIONS
5S0652Z
EU MAINS
CABLE
28
36
13
39
POWER
SOCKET
15
2
32
41
15
14
14
16
SOCKET 3
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO TILT ACTUATOR AND
ROUTED THROUGH CABLE DUCTS
16
14
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
6
10
1
11
3
12
2
13
1
14
8
15
2
16
8
17
6
18
12
19
1
20
2
21
5
22
20
23
8
24
6
25
6
26
2
27
2
28
1
29
5
30
1
31
1
32
1
33
1
34
2
35
1
36
1
37
3
38
1
39
1
40
1
41
1
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0952Z
5F0954Z
5F0955Z
5F0956Z
5J7866A
5J8067A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0652Z
5S0655Z
5S0656Z
5U1116Z
5U1121Z
S6243
S9108
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01069 230V EU Power Unit
LA317700+1015002P Actuator
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x65mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box Cable
912100 EU Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
225Kg Load Warning Label
Earth Label
Cable Gland (Bell End Split)
0821008 CU20 Blanking Plug
HAND/FOOT
DEVICE
16
14
3
16
SHEET 2 OF 2
SOCKET 1
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO BACKREST ACTUATOR
AND ROUTED THROUGH CABLE DUCTS
1
EARTH CABLE CONNECTION TO BE FITTED
ON INSIDE FACE OF SIDE MEMBER
UNDER CONTROL BOX BRACKET
SOCKET 2
CONTROL BOX CABLE 5F0650Z TO BE
PLUGGED INTO BASE ACTUATOR AND
SECURED ALONG H SECTION
40
UNCONTROLLED WHEN PRINTED
MAINS CABLE TO PASS THROUGH CABLE
GLAND TO CREATE STRAIN RELIEF ON THE
MAINS CABLE
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
gary.mullenger
CAD NO
2R11234Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
22/10/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
Linak 230v EU Clinical Tilt & Electric Backrest Ram Kit
REVISION STATUS
ISSUE
1
DATE
10/07
DCN
1256
ASSEMBLY
2R11234Z
ISSUE
1
120V EU LINAK TILT E/BACK
11
CHANNEL CUT
LENGTH 0.4M
29
CHANNEL CUT
LENGTH 0.1M
29
29
22
22
22
21
22
CONTROL BOX CABLE 5F0651Z FROM TILT
ACTUATOR TO BE PLUGGED INTO SOCKET 3 OF
CONTROL BOX AND ROUTED THROUGH DUCTING
CHANNEL ON MAIN FRAME/H SECTION
CHANNEL CUT
LENGTH 0.2M
25
11
6
22
CONTROL BOX CABLE 5F0651Z FROM BACKREST
ACTUATOR TO BE PLUGGED INTO SOCKET 1 OF
CONTROL BOX AND ROUTED THROUGH DUCTING
CHANNEL ON MAIN FRAME/H SECTION
22
37
37
22
22
21
20
8
10
25
12
20
19
22
23
22
9
18
22
37
18
26
3A10004P FRONT
ACTUATOR MOUNTING
BRACKET
18
26
22
7
18
17
29
24
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01169 120V US Power Unit
LA317700+1015002P Actuator
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x65mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box Cable
912100 EU Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
225Kg Load Warning Label
Earth Label
Cable Gland (Bell End Split)
0821008 CU20 Blanking Plug
SHEET 1 OF 2
23
23
24
24
22
22
21
17
23
23
22
24
UNCONTROLLED WHEN PRINTED
17
18
9
22
18
21
22
25
18
23
38
18
3A10005P REAR
ACTUATOR MOUNTING
BRACKET
23
31
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0953Z
5F0954Z
5F0955Z
5F0956Z
5J7866A
5J8067A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0652Z
5S0655Z
5S0656Z
5U1116Z
5U1121Z
S6243
S9108
CURLY CONTROL BOX CABLE 5F0650Z FROM
BASE ACTUATOR TO BE PLUGGED INTO
SOCKET 2 OF CONTROL BOX
17
12
CURLY WRAP
LENGTH 0.13M
25
23
9
CHANNEL CUT
LENGTH 0.18M
21
22
22
27
30
11
22
25
27
CURLY WRAP
LENGTH 0.13M
29 CHANNEL CUT
LENGTH 0.2M
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
6
10
1
11
3
12
2
13
1
14
8
15
2
16
8
17
6
18
12
19
1
20
2
21
5
22
20
23
8
24
6
25
6
26
2
27
2
28
1
29
5
30
1
31
1
32
1
33
1
34
2
35
1
36
1
37
3
38
1
39
1
40
1
41
1
25
9
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
gary.mullenger
CAD NO
2R11235Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
22/10/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
Linak 120v EU Clinical Tilt & Electric Backrest Ram Kit
REVISION STATUS
ISSUE
1
DATE
10/07
DCN
1256
ASSEMBLY
2R11235Z
ISSUE
1
120V EU LINAK TILT E/BACK
406
90
15
4
5
5S0216Z
EARTH
CABLE
CONTROL BOX HOLE POSITIONS
28
36
13
39
15
2
32
41
15
14
14
16
SOCKET 3
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO TILT ACTUATOR AND
ROUTED THROUGH CABLE DUCTS
16
14
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
6
10
1
11
3
12
2
13
1
14
8
15
2
16
8
17
6
18
12
19
1
20
2
21
5
22
20
23
8
24
6
25
6
26
2
27
2
28
1
29
5
30
1
31
1
32
1
33
1
34
2
35
1
36
1
37
3
38
1
39
1
40
1
41
1
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0953Z
5F0954Z
5F0955Z
5F0956Z
5J7866A
5J8067A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0652Z
5S0655Z
5S0656Z
5U1116Z
5U1121Z
S6243
S9108
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01169 120V US Power Unit
LA317700+1015002P Actuator
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x65mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box Cable
912100 EU Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
225Kg Load Warning Label
Earth Label
Cable Gland (Bell End Split)
0821008 CU20 Blanking Plug
HAND/FOOT
DEVICE
16
14
3
16
SHEET 2 OF 2
SOCKET 1
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO BACKREST ACTUATOR
AND ROUTED THROUGH CABLE DUCTS
1
EARTH CABLE CONNECTION TO BE FITTED
ON INSIDE FACE OF SIDE MEMBER
UNDER CONTROL BOX BRACKET
SOCKET 2
CONTROL BOX CABLE 5F0650Z TO BE
PLUGGED INTO BASE ACTUATOR AND
SECURED ALONG H SECTION
40
UNCONTROLLED WHEN PRINTED
MAINS CABLE TO PASS THROUGH CABLE
GLAND TO CREATE STRAIN RELIEF ON THE
MAINS CABLE
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
gary.mullenger
CAD NO
2R11235Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
22/10/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
Linak 120v EU Clinical Tilt & Electric Backrest Ram Kit
REVISION STATUS
ISSUE
1
DATE
10/07
DCN
1256
ASSEMBLY
2R11235Z
ISSUE
1
120V EU LINAK TILT E/BACK
406
90
15
4
5
5S0216Z
EARTH
CABLE
CONTROL BOX HOLE POSITIONS
28
36
13
39
15
2
32
41
15
14
14
16
SOCKET 3
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO TILT ACTUATOR AND
ROUTED THROUGH CABLE DUCTS
16
14
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
6
10
1
11
3
12
2
13
1
14
8
15
2
16
8
17
6
18
12
19
1
20
2
21
5
22
20
23
8
24
6
25
6
26
2
27
2
28
1
29
5
30
1
31
1
32
1
33
1
34
2
35
1
36
1
37
3
38
1
39
1
40
1
41
1
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0953Z
5F0954Z
5F0955Z
5F0956Z
5J7866A
5J8067A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0652Z
5S0655Z
5S0656Z
5U1116Z
5U1121Z
S6243
S9108
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01169 120V US Power Unit
LA317700+1015002P Actuator
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x65mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box Cable
912100 EU Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
225Kg Load Warning Label
Earth Label
Cable Gland (Bell End Split)
0821008 CU20 Blanking Plug
HAND/FOOT
DEVICE
16
14
3
16
SHEET 2 OF 2
SOCKET 1
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO BACKREST ACTUATOR
AND ROUTED THROUGH CABLE DUCTS
1
EARTH CABLE CONNECTION TO BE FITTED
ON INSIDE FACE OF SIDE MEMBER
UNDER CONTROL BOX BRACKET
SOCKET 2
CONTROL BOX CABLE 5F0650Z TO BE
PLUGGED INTO BASE ACTUATOR AND
SECURED ALONG H SECTION
40
UNCONTROLLED WHEN PRINTED
MAINS CABLE TO PASS THROUGH CABLE
GLAND TO CREATE STRAIN RELIEF ON THE
MAINS CABLE
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
gary.mullenger
CAD NO
2R11235Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
22/10/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
Linak 120v EU Clinical Tilt & Electric Backrest Ram Kit
REVISION STATUS
ISSUE
1
DATE
10/07
DCN
1256
ASSEMBLY
2R11235Z
ISSUE
1
120V US LINAK TILT E/BACK
11
CHANNEL CUT
LENGTH 0.4M
29
CHANNEL CUT
LENGTH 0.1M
29
29
22
22
22
21
22
CONTROL BOX CABLE 5F0651Z FROM TILT
ACTUATOR TO BE PLUGGED INTO SOCKET 3 OF
CONTROL BOX AND ROUTED THROUGH DUCTING
CHANNEL ON MAIN FRAME/H SECTION
CHANNEL CUT
LENGTH 0.2M
25
11
6
22
CONTROL BOX CABLE 5F0651Z FROM BACKREST
ACTUATOR TO BE PLUGGED INTO SOCKET 1 OF
CONTROL BOX AND ROUTED THROUGH DUCTING
CHANNEL ON MAIN FRAME/H SECTION
22
37
37
22
22
21
20
8
10
25
12
20
19
22
23
22
9
18
22
37
18
26
3A10004P FRONT
ACTUATOR MOUNTING
BRACKET
18
26
22
7
18
17
29
24
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01169 120V US Power Unit
LA317700+1015002P Actuator
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x65mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box Cable
0912160 US Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
RS289-534 E Clip
225Kg Load Warning Label
Earth Label
0821008 CU20 Blanking Plug
SHEET 1 OF 2
23
23
24
24
22
22
21
17
23
23
22
24
UNCONTROLLED WHEN PRINTED
17
18
9
22
18
21
22
25
18
23
39
18
3A10005P REAR
ACTUATOR MOUNTING
BRACKET
23
31
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0953Z
5F0954Z
5F0955Z
5F0956Z
5J7866A
5J8067A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0653Z
5S0655Z
5S0656Z
5S0657Z
5U1116Z
5U1121Z
S9108
CURLY CONTROL BOX CABLE 5F0650Z FROM
BASE ACTUATOR TO BE PLUGGED INTO
SOCKET 2 OF CONTROL BOX
17
12
CURLY WRAP
LENGTH 0.13M
25
23
9
CHANNEL CUT
LENGTH 0.18M
21
22
22
27
30
11
22
25
27
CURLY WRAP
LENGTH 0.13M
29 CHANNEL CUT
LENGTH 0.2M
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
6
10
1
11
3
12
2
13
1
14
8
15
2
16
8
17
6
18
12
19
1
20
2
21
5
22
20
23
8
24
6
25
6
26
2
27
2
28
1
29
5
30
1
31
1
32
1
33
1
34
2
35
1
36
1
37
3
38
1
39
1
40
1
41
1
25
9
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
gary.mullenger
CAD NO
2R11236Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
22/10/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
Linak 120v US Clinical Tilt & Electric Backrest Ram Kit
REVISION STATUS
ISSUE
1
DATE
10/07
DCN
1256
ASSEMBLY
2R11236Z
ISSUE
1
120V US LINAK TILT E/BACK
406
15
4
90
5
5S0216Z
EARTH
CABLE
CONTROL BOX HOLE POSITIONS
28
36
13
40
15
2
32
41
15
14
14
16
SOCKET 3
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO TILT ACTUATOR AND
ROUTED THROUGH CABLE DUCTS
16
14
ITEM QTY
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
6
10
1
11
3
12
2
13
1
14
8
15
2
16
8
17
6
18
12
19
1
20
2
21
5
22
20
23
8
24
6
25
6
26
2
27
2
28
1
29
5
30
1
31
1
32
1
33
1
34
2
35
1
36
1
37
3
38
1
39
1
40
1
41
1
PART No.
3A10037P
3A10038P
5F0950Z
5F0951Z
5F0953Z
5F0954Z
5F0955Z
5F0956Z
5J7866A
5J8067A
5J8266A
5J8270A
5K0304R
5K1135T
5L2755K
5L2865K
5L3119C
5L3162K
5L3319C
5L3362K
5L3519C
5L3562K
5L3577X
5N0056X
5N0058X
5N2100M
5P8000Z
5S0216Z
5S0306Z
5S0326Z
5S0327Z
5S0335Z
5S0650Z
5S0651Z
5S0653Z
5S0655Z
5S0656Z
5S0657Z
5U1116Z
5U1121Z
S9108
ISSUE No.
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DESCRIPTION
Left Hand Control Box Bracket
Right Hand Control Box Bracket
CU2001006711064 Modular Control Box
BA2016-0200-00 Battery Box
CP2000000A01169 120V US Power Unit
LA317700+1015002P Actuator
LA343200+0020004U Actuator
LA317700+1120002P Actuator
M8x60 Hex Ht Bolt
M10x65mm Hex Bolt
M12x60mm Hex Bolt
M12x80mm Hex Bolt
No.8 x 5/16 PH Self-Tap
M5x12 Pan Head Set Screw
4mm Sakeproof Washer
M5 Flat Washer
M8 Nyloc Nut
M8 Washer Flat Form B
M10 Nyloc Nut
M10 Washer Flat Form B
M12 Nyloc Nut
M12 Washer Flat Form B
M12 Nylon Washer
M8 White Nut Cap
M12 White Nut Cap
8.5mm Grey Insert
Bronze Flanged Bush
1.5mm Earth Cable
Cable Ducting Channel
Curly Wrap
Large Curly Wrap
5mm Crimped Eyelet
0964008-200 Actuator/Control Box Cable
0964003-2500 Actuator/Control Box Cable
0912160 US Mains Cable
0988003 Blanking Plug
0961006-B Locking Ring
RS289-534 E Clip
225Kg Load Warning Label
Earth Label
0821008 CU20 Blanking Plug
HAND/FOOT
DEVICE
16
14
3
38
16
SHEET 2 OF 2
SOCKET 1
CONTROL BOX CABLE 5F0651Z TO BE
PLUGGED INTO BACKREST ACTUATOR
AND ROUTED THROUGH CABLE DUCTS
1
EARTH CABLE CONNECTION TO BE FITTED
ON INSIDE FACE OF SIDE MEMBER
UNDER CONTROL BOX BRACKET
SOCKET 2
CONTROL BOX CABLE 5F0650Z TO BE
PLUGGED INTO BASE ACTUATOR AND
SECURED ALONG H SECTION
35
UNCONTROLLED WHEN PRINTED
US MAINS CABLE STRAIN RELIEF TO BE
SECURED TO FIXING PLATE USING 1 OFF
E CLIP 5S0657Z
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
gary.mullenger
CAD NO
2R11236Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
22/10/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
Linak 120v US Clinical Tilt & Electric Backrest Ram Kit
REVISION STATUS
ISSUE
1
DATE
10/07
DCN
1256
ASSEMBLY
2R11236Z
ISSUE
1
ITEM QTY
1
1
PART No.
5F2110Z
ISSUE No.
DESCRIPTION
0
966.000.149 Hanning Single Handswitch
UNCONTROLLED WHEN PRINTED
1
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2006
DRAWN
GMullenger
2Z0300Z
CAD NO
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
13/06/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
Hanning Single Hand Switch with Magnet
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
4
ISSUE
5
DATE
01/96 06/06
DCN
0746 1225
ASSEMBLY
2Z0300Z
ISSUE
5
ITEM QTY
1
1
PART No.
5F0940Z
ISSUE No.
DESCRIPTION
0
6241-0015 Herga 3 Channel Footswitch
UNCONTROLLED WHEN PRINTED
1
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2006
DRAWN
gary.mullenger
A7330
CAD NO
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
12/06/2006
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Herga 3 Channel Foot Switch
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
1
ISSUE
2
DATE
12/04 06/06
DCN
1112 1224
ASSEMBLY
A7330
ISSUE
2
ITEM QTY
1
1
2
1
CB20 CONTROL BOX
PART No.
5F0957Z
5U1025Z
ISSUE No.
DESCRIPTION
0
Linak HB36V001+B0600 Handset
0
Linak HBW072041 Handswitch Overlay
1
2
600MM COILED LEAD
UNCONTROLLED WHEN PRINTED
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
A7325A
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
22/06/2004
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
Linak CB20 2 Way Handswitch Controller (Std~E/Back)
REVISION STATUS
ISSUE
1
DATE
8/07
DCN
1253
ASSEMBLY
A7325A
ISSUE
1
ITEM QTY
1
1
2
1
CB20 CONTROL BOX
1
PART No.
5F0957Z
5U1026Z
ISSUE No.
DESCRIPTION
0
Linak HB36V001+B0600 Handset
0
Linak Handswitch Overlay (HBW073065)
2
600MM COILED LEAD
UNCONTROLLED WHEN PRINTED
C
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
GMullenger
CAD NO
A7326A
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
22/06/2004
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
Linak CB20 3 Way Handswitch Controller (Std~EB~Tlt)
REVISION STATUS
ISSUE
1
DATE
10/07
DCN
1256
ASSEMBLY
A7326A
ISSUE
1
ITEM QTY
1
1
2
2
PART No.
5F0958Z
5K0311R
ISSUE No.
DESCRIPTION
0
DJB0002001-1020 Din Junction Box
0
No.8 x 1" PH Self-Tap
WHEN FITTING THE JUNCTION BOX ALWAYS ENSURE
THAT THE PLUG SOCKETS FACE THE CONTROL BOX
1
186
16
16
2
DRILL 2 HOLES n3.7 THRO
ONE FACE ON UNDERSIDE
OF H SECTION
FIXING DETAILS FOR DIN JUNCTION BOX
ONTO H SECTION
C
UNCONTROLLED WHEN PRINTED
COPYRIGHT. HUNTLEIGH
TECHNOLOGY PLC 2007
DRAWN
gary.mullenger
CAD NO
2R11227Z
THIS DRAWING IS NOT TO BE LOANED
TO THIRD PARTIES OR USED WITHOUT DATE
30/08/2007
WRITTEN CONSENT OF HUNTLEIGH
CHECKED &
AKRON LIMITED
APPROVED
TITLE
Streamline Din Junction Box
Patient Positioning Solutions
1 FARTHING ROAD
IPSWICH, SUFFOLK
IP1 5AP. ENGLAND
TEL: +44(0)1473 461042
FAX: +44(0)1473 462924
www.huntleigh-akron.com
REVISION STATUS
ISSUE
1
DATE
8/07
DCN
1253
ASSEMBLY
2R11227Z
ISSUE
1