Download Operating Instructions

Q.ERSA-0007
Operating Instructions
ERSA EWS 500 F-XL Technical data
3. Technical data ,
3.1 System, complete
Outside dimensions: see figure
_ 4140
a 3380
510
- 6150 |
т
N
| =
E
Seniceselie
6 dor
1
{
Pneumoikanschlud
preumatic connection на
ps
Service side
Absaugonschluf
— exhaust volume
AbsougomschluB o
exhoust volume === =
800 m! /h 400m /h 5
4 No
—
8
| |
Bedienseits Scheltschrank un
operotor side electrica! cobinet o
Ly
Dead weight: Approx. 1.400 kg
Power consumption: max. 59 kW
Input power:
Max. fuse:
3-phase 230/400 V, N, PE, corresp. DIN IEC 38
Тот = 50 HZ, lo, = 89.5 A
3 x 100 À slow blow
01/01 6GD0-EWS50-01
EVWS500XL_03eng.doc
Chapter 3 / Page 1
A Kurtz Company
QERSA0002
Operating Instructions
ERSA EWS 500 F-XL Technical data
3.2 Fluxer module
3.2.1 Foam fluxer
Flux capacity: approx. 4.5 liters (fluxer pan)
Working width: 450/500 mm
Foam height: approx. 10 mm
Flux storage tank: max 12 liters
3.22 ERSA Spray fluxer ESF
(see operating instructions — chapter 12, appendix)
3.2.3 Automatic density control device
Density measuring range: 0.75 — 0.85 g/cu.cm
(TA = 20 Degree C)
0.80 — 0.90 g/cu.cm
0.85 — 0.95 g/cu.cm
Resolution: 0.001 g/lcum
Measurement and control accuracy: +/- 0.002 g/cu.cm
Storage tanks:
Mixing tank max. 12 liters
(large chamber on the right)
Solvent tank max. 6 liters .
(small chamber on the left)
Solvent pump:
Pumping time per digit deviation approx. 2 sec _
Mixing time: approx. 3 min
(Time between 2 pumping cycles)
01/01 6GDO-EWS50-01 В Chapter 3 / Page 2
EWS500XL_03eng.doc A Le
Ele
FER
O
E
Пу Company
G.ERSA-O0002
Operating Instructions
ERSA EWS 500 F-XL
3.2.4 Flux blow-off device
Working width:
Blow-off pressure:
Pneumatic connection: -
Recommended blow-off pressure:
3.3 Preheating module
w
>
erh
Power:
Radiant temperature:
Effective preheating width:
Dimensions:
Heating-up time (max. temperature):
3.3.2 Short-wave emitter unit
Power‘
Effective preheating width:
Technical data
500 mm
0...3 bar (infinitely variable)
min. 4 bar
0.3 ~ 0.4 bar
Medium-wave heater cassette
max. 4 kW |
(5 emitters, each 800 W)
400...600°C
approx. 500 mm
Width 660 mm
Length 300 mm
approx. 5 min
6.6 KW (3 emitters, each 2.2 kW)
approx. 500 mm
Dimensions: Width 650 mm
| Length 150 mm
01/01 6GDO-EWS50-01 Chapter 3/ Page 3
EWS500XL_03eng.doc
AKUTE, Company
G.ERSACO02
Operating Instructions
ERSA EWS 500 F-XL Technical data
3.3.3 Dynamic preheating cassette
Power: max. 13.2 kW
| (6 emitters, each 2.2 kW)
Effective preheating width: approx. 500 mm
Dimensions: | Width 650 mm
Length 400 mm
3.3.4 Convection preheating module
Power: В max. 9.9 kW
Effective preheating width: ca. 500 mm
Dimensions: Width 350 mm
Length 830 mm
01/01 6GDO-EWS50-01 Chapter 3 / Page 4
EWS500XL_03eng.doc | -
G.ERSA-0002
Operating Instructions
ERSA EWS 500 F-XL Technical data
3.4 Soldering module
3.4.1 Wave soldering machine LM 9
Power: ca. 10.2 kW
Heating-up time: ca.35h
Weight without solder: approx. 90 kg
Solder capacity: approx. 550 kg
(with alloy Sn/Pb 64/36)
Effective wave width: | 480 mm
Wave height: max. approx. 10 mm
Solder temperature: 230 - 300°C
Temperature accuracy: + - 1% of target value
Shaft rotational speed: 200 — 600 rpm
3.5 Conveyor system
3.5.1 Finger conveyor sytem (frameless)
Conveyor speed: 0.5...2.5 m/min
Conveyor angle adjustment: 7 degrees
Wor King width: | 480 mm
01/01 6GDO-EWS50-01 Chapter 3 / Page 5
EWS500XL_03eng.doc
REPT Company
QLERSADODZ
Operating Instructions
ERSA EWS 500 F-XL Technical data
3.6 | Cooling module
Working width: 500 mm
Pneumatic connection: min. 4 bar
Compressed-air cooling:
Recommended setting:
3.7 Exhaust system
Connecting dimensions:
Extraction rate at exhaust port:
0...3 bar (infinitely variable)
approx. 1 bar
See figure, chapter 3, page 1
each exhaust port min. 400 cum/h 2 //). |} [ros er Ses
for ERSA Spray fluxer ESF
min. 800 cum/h +8 ВА 22 Les Pm Leroux
3.8 Permanent noise level
It is confirmed that the permanent noise level does not exceed 85 dB (A).
Subject to technical changes !
01/01 &6GD0-EWS50-01
EVS500XL_03eng.doc
Chapter 3 / Page 6 |
A Kurtz, Company