Download American Standard 7501.170.002 Installation Guide
Transcript
Installation Instructions 7500 7501 7502 7545 CENTERSET LAVATORY FAUCETS WITH GOOSENECK SPOUT Series Series Series Series Thank you for selecting American-Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. 1 CAUTION Certified to comply with ANSI A112.18.1M 6 0 1 8 5 R e v. 1 . 6 Turn off water at main supply. 9 Asesemble GASKET (1) to SHANKS (2) and insert FAUCET SHANKS through holes of SINK. Assemble RUBBER (3) and BRASS WASHERS (4), and LOCKNUTS (5) from underside of SINK. Drop UPPER LIFT ROD (6) through hole in BODY (models 7501 only), align BODY as far forward as possible and secure position by tightening LOCKNUTS (5). 8 11 Connect the HOT water supply to the left SHANK and the COLD water supply to the right SHANK using sealant, appropriate connectors, and COUPLING NUTS (7). 10 To change spout to a swivel spout: (7500, 7501 & 7502) 6 Unscrew SPOUT NUT (8) and remove SPOUT (9). Take SPOUT CLIP (10) off SPOUT (9) and remove RUBBER RING (11). Replace RUBBER RING (11) with seperate PLASTIC RING (12) packed with faucet. Put SPOUT CLIP (10) on SPOUT. 1/2" O.D. SLIP Reassemble SPOUT (9) to BODY. 2 GRID DRAIN ASSEMBLY (Model 7502 only) BODY SINK 3 2 3 4 5 Insert threaded end of TAILPIECE (6) into lower end of DRAIN PLUG (2). Connect other end to trap. 4 5 COLD HOT 2 INSTALL POP-UP DRAIN (Model 7501 only) Adjust STOPPER (8) height by repositioning EXTENSION and tightening THUMBSCREW (12). SINK PUTTY Feed DRAIN BODY (5) up through SINK and thread FLANGE (6) fully onto BODY (5). 10 11 4 3 Tighten LOCKNUT (2) firmly, keeping the PIVOT ROD (7) pointed towards the back of the SINK. 5 Drop STOPPER (8) into DRAIN BODY (5). 2 Pull TAILPIECE (1) up and thread tightly into DRAIN BODY (5). Position EXTENSION ROD (9) onto POP-UP ROD (10) and tighten THUMBSCREW (11). TEST INSTALLED FAUCET 7 Insert PIVOT ROD (7) into second or third hole in EXTENSION (9) and reassemble CLIP (12). (EXTENSION may need to be bent.) 6 Apply a bead of PUTTY to underside of FLANGE (6). 7 Remove one end of CLIP (12) from PIVOT ROD (7) by squeezing ends together while sliding. 8 Push TAILPIECE (1) down into TRAP (threaded end up). 4 SINK PUTTY Hold DRAIN PLUG (2) to prevent turning and assemble GASKET (3), WASHER (4) and LOCKNUT (5) from underneath sink. Thread LOCKNUT (2), WASHER (3) and GASKET (4) onto DRAIN BODY (5). 1 1 Apply a bead of PUTTY around underside of DRAIN PLUG FLANGE (1). Insert DRAIN PLUG (2) into SINK drain hole. 3 12 2 7 12 9 12 7 1 TRAP Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks. Remove AERATOR. Operate LIFT ROD and check DRAIN for leaks. With handle in OFF position, turn on water supplies and check all connections for leaks. Turn handles into OFF position and replace AERATOR. 5 90° SERVICE STOP WASHER To change direction of handle rotation, proceed as follows: Turn valve to OFF position. Remove HANDLE and BONNET NUT. Remove SPRING CLIP. Lift STOP WASHER, turn 90° and replace. Replace SPRING CLIP. Replace BONNET NUT, HANDLE, SCREW, and INDEX. AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean. SPRING CLIP If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°. Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then: Remove HANDLE and BONNET NUT. Remove CARTRIDGE by pulling up. CARTRIDGE Thoroughly rinse plastic SCREEN at base of CARTRIDGE. Replace CARTRIDGE until flange is tight against valve body. Turn valves OFF. Replace BONNET NUT, HANDLE, SCREW and INDEX. SCREEN 7500 Series 7502 Series 7501 Series 7545 Series GRID DRAIN M922858-0020A VR AERATOR, 0.35gpm/1.3L/min. M922880-0020A AERATOR, 1.5gpm/5.7L/min. 015025-YYY0A DRAIN COMPLETE 066114 -0020A VR AERATOR, 0.5gpm/1.9L/min 051214-0070A SWIVEL/FIXED SPOUT RINGS 070532-0040A M923208-0070A TAILPIECE FLOW RESTRICTOR (7500.180, 7500.188 7500.186) 000690-0020A HANDLE SCREW 066497-0020A 051211-0070A COMPLETE DRAIN BODY INDEX KIT 066116-YYY0A DRAIN STOPPER M918014-0070A ADAPTER 051322-0020A VANDAL PROOF SCREW 000690-0020A HANDLE SCREW 051211-0070A INDEX KIT 051217-0020A WRIST BLADE HANDLE KIT M918014-0070A ADAPTER 012087-0070A SPOUT SEAL KIT 904939-0020A BONNET NUT 051210-0020A LEVER HANDLE 028617-0020A POP-UP ROD 951764-0070A CARTRIDGE POP-UP DRAIN 066117-YYY0A FLANGE KIT M919646-0020A SPOUT M964387-0020A 8" SPOUT (7500.177) 072574-0070A EXTENSION ROD 070847-0070A CLIP 066118-0070A PIVOT ROD M919658-0020A 8" SPOUT (7500.188) A919641-0020A 5" SPOUT (7500.180) 911928-0070A GASKET M919246-0020A 6" SPOUT (7500.186) 030255-0070A MOUNTING KIT 0-RING 900864-0070A DRAIN BODY 024220-0070A COUPLING NUT TAILPIECE INSERT 070532-0070A TAILPIECE HOT LINE FOR HELP For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-1200 6 0 1 8 5 R e v. 1 . 6 Product names listed herein are trademarks of American Standard Inc. © AS America, Inc. 2008