Download Grandio Greenhouses ELITE-16 Use and Care Manual

page
1
page
2
page
3
page
4
page
5
page
6
page
7
page
8
page
9
page
10
page
11
page
12
page
13
page
14
page
15
page
16
page
17
page
18
page
19
page
20
page
21
page
22
page
23
page
24
page
25
page
26
page
27
page
28
page
29
page
30
page
31
page
32
page
33
page
34
page
35
page
36
page
37
page
38
page
39
page
40
page
41
page
42
page
43
page
44
page
45
page
46
page
47
page
48
page
49
page
50
page
51
page
52
page
53
page
54
page
55
page
56
page
57
page
58
page
59
page
60
page
61
page
62
page
63
page
64
page
65
page
66
page
67
page
68
page
69
page
70
page
71
page
72
page
73
page
74
page
75
page
76
page
77
page
78
page
79
page
80
page
81
page
82
Transcript 
GRANDIO
G R E E N H O U S E S
2015 GRANDIO ELITE 8x12, 8x16, 8x20, 8x24 KIT MANUAL
INCLUDES INSTRUCTIONS FOR BACK DOOR TRANSFORMATION
Grandio Elite 8x24 Shown In Image
GREENHOUSE USER MANUAL
© 2013 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved
2015 Manual Edition Extendable Greenhouses
GRANDIO
G R E E N H O U S E S
Dear Valued Customer,
We would like to congratulate you on your new
Grandio Greenhouse purchase. We are confident
that you have made the right decision in choosing Grandio. Our greenhouses are made with
high quality aluminium and polycarbonate and
will last for many garden seasons to come.
Please take the time to carefully read this
instruction manual for an easier and more
enjoyable assembly experience.
Cheers!
Grandio Greenhouses
IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY
Before you begin, take time to complete this check list.
Take inventory of all parts using the parts list at the back of this manual on
pages 67-76. The base kit parts list is at the front on page 12 and 13. The back
door transformation kit parts list is on page 77.
Be cautious where you place the polycarbonate panels as they will burn grass
or plants if left on top of them in direct sunlight. Note that clear film side of
panels should always face the sun and white film side faces inside greenhouse. Panels may scratch easily so be careful what you clean them with.
Plan out when and where you are going to place the greenhouse, we recommend that you place it in an area that will receive direct sunlight and will be
protected from the wind as much as possible
It will take at least (2) people to put the greenhouse together.
Save this owner’s manual for future
reference and if you need our help.
CONTACT OUR CUSTOMER SERVICE
DEPARTMENT at:
1-866-448-8231
Hours: 8:30a.m.-5:00p.m. Monday through
Friday (Mountain Standard Time)
Backyard Living Source
9543 W. Emerald St., Suite 101
Boise, ID 83704
www.grandiogreenhouses.com
Before your build, make sure you are allowed to build it! Consult all building
codes, as well as City or Municipality ordinances and HOA’s, as you may need
a permit or documentation before you build.
Contact your insurance company to make sure your Grandio Greenhouse will
be covered on your policy.
Call your local utilities companies before digging.
Do not attempt to begin construction on a windy day.
Your greenhouse should be built on a flat level surface allowing for drainage.
Read this entire manual to get familiar with all pieces and parts prior to
beginning assembly. Follow the steps outlined in the order presented!
1
IMPORTANT! SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and
inside all packing material for parts and/or additional instruction materials. Before beginning assembly, read the instructions and identify all parts using the hardware identifier and parts list on pages 67-76. Complete assembly and
proper usage are essential to reduce the risk of accident or injury when using your Grandio Greenhouse.
CAUTION: Do not leave polycarbonate panels laying on grass or leave in the sun or extreme heat, keep in a cool
dry place until they are to be installed!! (May cause burning to plants or grass if left directly on top of them, also may
damage panels due to the protective film adhering to panels.) Panels may scratch easily. Do Not use solvent cleaners.
• Each of the polycarbonate panels have a transparent film side that should always face the sun, and a white film side which faces
inside. The clear side has a UV coating and we recommend marking a small “x” on a corner of each panel to determine which side
has the UV Coating as you cannot visually determine with your eye in the case of future disassembly.
• Due to shipping, the grooves of some of the aluminum profiles may be too small to insert into the polycarbonate sheet, you may
carefully use a screwdriver to pry the framework open so the polycarbonate sheet can be inserted smoothly.
• Do not use or store hot objects such as grills, blow torches, welding equipment, etc. in or near your greenhouse.
• Do not allow children or pets to play in greenhouse or in the set up area until assembly is complete.
• If using a ladder during assembly, use extreme caution.
• A clean level surface is essential to maintaining the solid integrity of the structure, Install the base correctly as described in
manual. Please anchor the greenhouse down to a firm and level base.
TOOLS YOU WILL NEED FOR ASSEMBLY
• Tape Measure
• 2 Step Ladders
• Level
• Work Gloves
• Carpenter Square
• Permanent Marker
• At Least 2 Adults
• Masking Tape
GRANDIO
• Safety Glasses
• Drill
• Knee Pads
• Folding Utility Table
2
TIP
When you see this icon
pay special attention to
the helpful tips we have provided that will
make installation more efficient.
GRANDIO
©
G R E E N H O U S E S
ASSEMBLY INSTRUCTION STEPS
PREPARE FOR ASSEMBLY
STEP ONE: BASE ASSEMBLY
STEP TWO: FRONT ASSEMBLY
STEP THREE: BACK ASSEMBLY
STEP FOUR: MIDDLE ASSEMBLY
STEP FIVE: EXTENSION ASSEMBLY
STEP SIX: DOOR ASSEMBLY
STEP SEVEN: INTERIOR ROOF SUPPORTS
3
Introduction.............................................................................1
Safety Instructions.................................................................2
Prepare For Assembly...........................................................4
Box Configurations ...............................................................5
Diagrams of Assembled Grandio Elite Sizes
8x8, 8x12, 8x16, 8x20, 8x24.........................6-10
Base Kit Assembly Information.......................................11
Base Kit Parts Lists........................................................12-13
8x12 Base Kit........................................................................14
8x16 Base Kit........................................................................15
8x20 Base Kit........................................................................16
8x24 Base Kit........................................................................17
Base Kit Assembly and Installation..............................18
Front Wall Assembly....................................................21-26
Back Wall Assembly.....................................................27-32
Middle Assembly.........................................................33-38
Extension Assembly...................................................39-46
8x20 and 8x24 Extension Assembly.....................47-50
Extension Assembly Continued.............................51-59
Door Assembly.............................................................60-65
Interior Roof Supports.....................................................66
GRA-ELI-8A Parts List.................................................67-69
GRA-ELI-8P Parts List........................................................70
GRA-ELI-4X Parts List.................................................71-73
GRA-ELI-8XA Parts List..............................................74-75
GRA-ELI-8XP Parts List....................................................76
GRA-ELI-BD Parts List......................................................77
Warranty..............................................................................78
PREPARE FOR GREENHOUSE ASSEMBLY
IMPORTANT: BASE KIT ASSEMBLY &
GREENHOUSE PLACEMENT
8X12 GRANDIO ELITE BARN STYLE
GREENHOUSE DIMENSIONS
Before assembling your new greenhouse, a proper
foundation must be prepared. A number of anchoring options are acceptable, based on wind and
ground conditions in your area.
The UV-Protected side is covered with transparent film
and must face toward the sun. The side covered in white
film will always face the interior of the greenhouse. We
suggest you peel all film off completely prior to assembly and use a permanent marker to place a small “X” on
the lower right corner of each panel on the transparent
side that faces the sun, each panel has a sticker labeling
the panel number and this side always faces the sun or
outward as well. DO NOT REMOVE LABELS UNTIL
YOU INSTALL PANELS. The “X” is suggested in case
you dis-assemble your greenhouse in the future so you
may identify which side has the UV coating. Always use
gloves when handling the polycarbonate panels as the
edges can be very sharp.
1 3/4”
GUTTERS
61”
LE
144”
FT
8X SID
12 E
44”
97.5”
Sun
Transparent Film
Polycarbonate
Panels
*SEE BASE KIT ASSEMBLY SECTION FOR ALL
GREENHOUSE BASE DIMENSIONS ON PAGES 14-17.
Opal White Film
4
DOOR HEIGHT
96”
IMPORTANT: POLYCARBONATE PANELS
EAVE HEIGHT
Go to www.grandiogreenhouses.com for foundation ideas and tour our online learning center for
tips, tricks and videos for putting your greenhouse
together.
ROOF PEAK HEIGHT
Pre-read pages 11-20 for base kit assembly information.
74”
EXTENSION KIT BOX CONFIGURATIONS
We recommend that you lay all of your boxes out as shown below for an organized assembly. Locate your greenhouse size and situate near
your assembly site. We suggest you lay the parts out on a tarp so you do not lose items in the grass or dirt near your building site.
*See the reference diagrams on pages 6-10 for more information about how the parts will go together and what makes up each section for
the assembly. If building a back door you will follow the instructions in the manual, the parts for the transformation are in box GRA-ELI-BD.
GRANDIO ELITE 8X16
Elite 8’x8’
GRA-ELI-8A
+
GRA-ELI-8P
Back
Back
Aluminum Extrusions,
Hardware Bag, 4’ Base
Extension, 1 Roof Vent,
2 Snow Load Extension
Supports, Polycarbonate Panels for 4’
Extension.
Front
Aluminum Extrusions,
Hardware Bag, Front,
Back and Doors.
GRA-ELI-4X
Aluminum Extrusions,
Hardware Bag, 8’ Base
Extension, 2 Roof
Vents, 2 Snow Load
Extension Supports.
GRA-ELI-8XP
8x8 Base Kit
+
GRA-ELI-8P
Back
Aluminum Extrusions,
Hardware Bag, Front,
Back and Doors.
Front
Back
+
Aluminum Extrusions,
Hardware Bag, 8’ Base
Extension, 2 Roof
Vents, 2 Snow Load
Extension Supports.
Elite 8’ Extension
GRA-ELI-8A
GRA-ELI-8XA
GRA-BAS-8
Base kit & hardware
GRANDIO ELITE 8X24
Elite 8’x8’
Elite 8’ Extension
Polycarbonate Panels
For The 8’ Extension
8x8 Base Kit
GRA-BAS-8
Base kit & hardware
5
Elite 8’x8’
Elite 8’ Extension
GRA-ELI-8XA
GRA-ELI-8XA
Aluminum Extrusions,
Hardware Bag, 8’ Base
Extension, 2 Roof
Vents, 2 Snow Load
Extension Supports.
Aluminum Extrusions,
Hardware Bag, 8’ Base
Extension, 2 Roof
Vents, 2 Snow Load
Extension Supports.
+
Polycarbonate Panels
GRA-ELI-8XP
GRA-ELI-8P
8x8 Base Kit
Polycarbonate Panels
For The 8’ Extension
GRANDIO ELITE 8X20
Aluminum Extrusions,
Hardware Bag, 4’ Base
Extension, 1 Roof Vent,
2 Snow Load Extension
Supports, Polycarbonate Panels for 4’
Extension.
+
Polycarbonate Panels
Base kit & hardware
GRA-ELI-4X
Aluminum Extrusions,
Hardware Bag, Front,
Back and Doors.
Polycarbonate Panels
GRA-BAS-8
Elite 4’ Extension
GRA-ELI-8A
GRA-ELI-8XA
GRA-ELI-8A
Aluminum Extrusions,
Hardware Bag, Front,
Back and Doors.
+
GRA-ELI-8P
Polycarbonate Panels
GRA-ELI-8XP
GRA-ELI-8P
Polycarbonate Panels
For The 8’ Extension
Polycarbonate Panels
For The 8’ Extension
8x8 Base Kit
GRA-BAS-8
Base kit & hardware
Front
Elite 4’ Extension
Elite 8’x8’
Elite 8’ Extension
Front
GRANDIO ELITE 8X12
BACK
L08A
606-WS
L08B-X
606-WS
606-WS
DIAGRAM SHOWS THE ASSEMBLED
(8’x8’ BASIC CONFIGURATION)
(GRA-ELI-8A & GRA-ELI-8P & GRA-BA-8)
8x8 ELITE KIT INCLUDES, FRONT,
BACK, BASE AND SIDES.
BA-S1
606-WS
L08B-X
601A-B
601A-B
Y1
Y1
Y1
Y1
Outside View
L08B
601A-B
L08C-X
606-WS
609
610
Y8
Y7
BA-S2
Y7
602A
606-WS
618
Y9 Y10
Y7
602A
Y11
609
601A-FL
LEFT SIDE
610
603C
602D
Y4-2
Y8
603C
Y5-2
601B
630
Y5-1
601B
601B
610
609
Y3-1 Y3-2
603E
Y2-1
L08D
603C
601A-FL
604-L
Y1
L08A-X
606-WS
623B
630
603D
623B
622-L
Y6
622-R
Y6
622
622
620
620
Y6
Y6
623B
623B
619
Y8
L08D
FRONT
L21
Y11
610
Y1
L08A-X
606-WS
601A-B
L08C-X
606-WS
Y7
602A
Y7
603C/616
606-WS
BA-S2
602A
602B
Y11
Y8
601A-FR
606-WS
Y7
Y8
609
603C
604-R
609
602B
601B
Y2-2
BA-S1
6
610
Y11 618
Y10 Y9
601B
630
609
602B
601B
607
Y11
630
Y11
630
601B
Y11
610
603C
602D
Y4-1
602C
Y11
602B
Y8
603C
601B
602B
Y7
L08C-X
606-WS
630
602B
602A
606-WS 603C/616
609
602A
Y7
609
606-WS
L08C-X
601A-FR
RIGHT SIDE
4X Elite Side
7
8x8 Elite Side
602A
602A
603C/616
609
Y7
Y7
L08D-X
Y8
609
602B
Y8
602B
618
Y9 Y10
602B
610 609
L08D-X
Y8
602B
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
602B
610
601B
601A-FL
L08E-X
Y11
602B
Y11
602B
Y11
602B
Y11
630
L08E-X
602B
Y11
607
623B
Y6
620
622
622-R
Y6
623B
630
Y1
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
619
L08A-X
606-WS
604-R
603C
L08D
Y2-2
601B
630
603C
602D
Y4-1
Y1
L08B-X
606-WS
601B
603D
FRONT
623B
L08A-X
606-WS
BA-S1
Y6
Y1
620
622
623B
603E
603C
604-L
Y5-1
603C
Y1
606-WS
Y3-1 Y3-2
607
622-L
Y6
Y2-1
601B
601B
602C
L08D
630
601B
630
Y5-2
603C
L08B
Y1
Outside View
LEFT SIDE
602A
602A
Y7
Y7
609
Y7
618
Y9 Y10
602B
Y8
Y7
630
L08E-X
Y11
603C
602D
Y4-2
Y1
606-WS
L08A
DIAGRAM SHOWS THE ASSEMBLED
8X12 GRANDIO ELITE
THE BOX CONFIGURATION IS AN ELITE 8X8
PLUS AN 4 FOOT EXTENSION KIT
L08C-X
606-WS
606-WS
BA-S2
606-WS 603C/616
L08C-X
606-WS
AZ1
BA-S5
606-WS
602A
L08C-X
606-WS
610 609
L08D-X
609
610
601A-B
606-WS
BA-S1
L08B-X
BACK
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
Y11
601A-FR
610
601B
Y11
602B
Y11
602B
602B
602A
602A
603C/616
602A
602A
602A
L08C-X
606-WS
606-WS
BA-S2
606-WS
L08C-X
606-WS
AZ1
606-WS
L08C-X
606-WS
RIGHT SIDE
609
Y7
Y7
Y7
Y7
609
Y7
Y7
609
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
L08D-X
Y8
609
602B
Y8
618
Y10 Y9
602B
L08D-X
Y8
609 610
602B
602B
Y8
Y8
610
609
L08D-X
Y11
602B
Y11
630
602B
L08E-X
L21
Y11
602B
L08E-X
601B
630
L08E-X
610
601A-B
(4’ Extension Side) (GRA-ELI-4X)
Elite 4’ Side Extension
Includes Base
(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BA-8)
8x8 Elite Includes Front, Back, Base, and Sides
(8’ Extension Side) 8X Elite Side
8x8 Elite Side
602A
602A
603C/616
602A
602A
602A
8
Y8
L08D-X
Y8
609
602B
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
LEFT SIDE
609
Y7
Y7
602B
618
Y9 Y10
602B
610
601A-FL
L08E-X
Y11
602B
Y11
602B
Y11
602B
601B
610
601B
630
L08E-X
610 609
L08D-X
Y8
Y11
602B
Y11
602B
Y11
Y11
602B
618
Y9 Y10
602B
Y8
602B
Y8
Y11
630
L08E-X
607
623B
Y6
620
FRONT
623B
Y6
620
622
622-R
Y6
623B
630
603C
602D
Y4-1
630
619
Y1
601B
601A-FR
L21
L08E-X
610
Y11
602B
Y11
602B
Y11
602B
630
602B
Y11
602B
602B
602A
602A
603C/616
602A
602A
602A
602A
603C/616
602A
L08C-X
606-WS
606-WS
BA-S2
606-WS
L08C-X
606-WS
AZ1
606-WS
BA-S4
606-WS
606-WS
L08C-X
606-WS
RIGHT SIDE
609
Y7
Y7
Y7
Y7
609
Y7
Y7
Y7
Y7
609
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
L08D-X
Y8
609
602B
Y8
602B
618
Y10 Y9
602B
609 610
L08D-X
Y8
Y8
602B
602B
602B
Y11
Y8
618
Y10 Y9
602B
609 610
L08D-X
Y11
602B
630
L08E-X
Y11
L08E-X
Y11
610
601A-B
601B
L08A-X
606-WS
604-R
603C
L08D
Y2-2
601B
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
BA-S1
606-WS
L08A-X
Y1
604-L
622
603C
623B
603E
606-WS
L08B-X
Y1
601B
603D
Y5-1
603C
Y1
606-WS
Y3-1 Y3-2
607
622-L
Y6
Y2-1
601B
601B
602C
Y5-2
603C
L08B
Y1
L08D
630
630
603C
602D
Y4-2
Y1
606-WS
L08A
DIAGRAM SHOWS THE ASSEMBLED
8X16 GRANDIO ELITE
THE BOX CONFIGURATION IS AN ELITE 8X8
PLUS AN 8 FOOT EXTENSION KIT
L08C-X
606-WS
602A
602A
Y7
Y7
609
Y7
Y7
Y7
Y8
Y7
602B
610 609
L08D-X
609
606-WS
L08B-X
BA-S1
Outside View
606-WS
BA-S2
606-WS 603C/616
L08C-X
606-WS
AZ1
BA-S3
606-WS
606-WS
606-WS
L08C-X
606-WS
601A-B
BACK
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
(8’ Extension Side) (GRA-ELI-8XA &GRA-ELI-8XP)
Elite 8’ Side Extension includes Base
(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BA-8)
8x8 Elite Includes Front, Back, Base, and Sides
(8’ Extension Side) 8X Elite Side
(4’ Extensions Side) 4X Elite Side
9
606-WS
609
Y7
Y7
L08D-X
Y8
609
602B
Y8
602B
618
Y9 Y10
LEFT SIDE
602A
602A
Y7
602B
610
L08E-X
Y11
602B 601A-FL
Y11
602B
Y11
602B
601B
630
L08E-X
610 609
L08D-X
Y8
Y11
602B
602B
Y11
602B
Y11
Y11
Y11
601B
610
630
L08E-X
602B
618
Y9 Y10
602B
Y8
602B
Y8
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
606-WS
L08C-X
606-WS
BA-S2
603C/616
Y7
609
Y7
Y7
Y7
Y8
Y7
602B
610 609
L08D-X
609
602B
Y11
602B
Y2-1
607
623B
Y6
620
622
622-R
Y6
623B
603D
FRONT
623B
Y6
620
622
622-L
Y6
623B
603E
Y3-1 Y3-2
607
607
601B
630
603C
602D
Y4-1
Y1
606-WS
L08B-X
630
Y1
619
610
601B
Y11
602B
Y11
602B
630
602B
Y11
602B
602B
Y11
Y11
602B
630
L08E-X
Y11
602B
Y11
602B
Y11
L08E-X
Y11
601A-FR 602B
L21
630
L08E-X
L08E-X
Y11
610
601A-B
601B
L08A-X
606-WS
604-R
603C
L08D
Y2-2
601B
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
BA-S1
606-WS
L08A-X
Y1
604-L
603C
Y5-1
Y5-2
602C
603C
Y1
606-WS
603C
L08B
Y1
606-WS
601B
601B
L08D
630
630
603C
602D
Y4-2
Y1
606-WS
L08B-X
L08A
DIAGRAM SHOWS THE ASSEMBLED
8X20 GRANDIO ELITE
THE BOX CONFIGURATION IS AN ELITE 8X8
PLUS AN 8 FOOT AND A 4 FOOT EXTENSION KIT
606-WS
L08C-X
606-WS
AZ1
602A
603C/616
602A
602A
602A
602A
606-WS
606-WS
L08C-X
606-WS
602A
Y7
618
Y9 Y10
602B
Y8
Y7
601A-B
630
L08E-X
Y11
BA-S1
Outside View
BA-S3
AZ1
BA-S5
606-WS 603C/616
602A
L08C-X
606-WS
610 609
L08D-X
609
BACK
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
602B
602B
602B
AZ1
606-WS
602A
602A
603C/616
602A
602A
602A
602A
603C/616
602A
L08C-X
606-WS
606-WS
BA-S2
606-WS
L08C-X
606-WS
AZ1
606-WS
BA-S4
606-WS
606-WS
L08C-X
606-WS
602A
602A
BA-S6
606-WS
L08C-X
RIGHT SIDE
609
Y7
Y7
Y7
Y7
609
Y7
Y7
Y7
Y7
609
Y7
Y7
609
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
L08D-X
Y8
609
602B
Y8
602B
618
Y10 Y9
602B
609 610
L08D-X
Y8
Y8
Y8
618
Y10 Y9
602B
609 610
L08D-X
602B
602B
Y8
Y8
610
609
L08D-X
(8’ Extension Side) (GRA-ELI-8XA & GRA-ELI-8XP)
Elite 8’ Side Extension includes Base
8x8 Elite Side
(4’ Extension Side) (GRA-ELI-4X)
Elite 4’ Side Extension
Includes Base
(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BA-8)
8x8 Elite Includes Front, Back, Base, and Sides
(8’ Extension Side) 8X Elite Side
(8’ Extension Side) 8X Elite Side
10
609
Y7
L08D-X
Y8
609
602B
Y8
602B
618
Y9 Y10
602B
610
L08E-X
Y11
602B 601A-FL
Y11
602B
Y11
602B
601B
610
601B
630
L08E-X
610 609
L08D-X
Y8
Y11
602B
Y11
602B
Y11
Y11
602B
LEFT SIDE
602A
Y7
Y7
Y7
609
Y7
618
Y9 Y10
602B
Y8
602B
Y8
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
L08C-X
606-WS
606-WS
602A
603C/616
602A
602A
603C/616
Y7
Y7
Y8
Y7
602B
630
L08E-X
610 609
L08D-X
609
Y11
602B
Y11
602B
Y11
Y11
601A-B
602B
Y7
618
Y9 Y10
602B
Y8
602B
Y8
Y11
607
623B
Y6
620
622
622-R
Y6
623B
603D
FRONT
623B
Y6
601B
630
603C
602D
Y4-1
Y1
L08B-X
606-WS
L08A
630
Y1
619
610
601B
Y11
602B
Y11
602B
L08E-X
Y11
601A-FR 602B
L21
630
602B
Y11
602B
602B
Y11
Y11
602B
630
L08E-X
Y11
602B
Y11
602B
602B
602B
602B
602B
602A
AZ1
606-WS
606-WS
BA-S4
L08C-X
606-WS
AZ1
606-WS
BA-S4
606-WS
606-WS
RIGHT SIDE
L08C-X
606-WS
602A 606-WS
BA-S2
602A 606-WS
603C/616
602A
602A
602A
602A
603C/616
602A
L08C-X
606-WS
602A
602A
602A
606-WS
L08C-X
606-WS
603C/616
609
Y7
Y7
Y7
Y7
609
Y7
Y7
Y7
Y7
609
Y7
Y7
Y7
Y7
609
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
L08D-X
Y8
609
602B
Y8
602B
618
Y10 Y9
602B
609 610
L08D-X
Y8
Y8
Y8
618
Y10 Y9
602B
609 610
L08D-X
Y8
602B
602B
602B
Y11
Y8
618
Y10 Y9
602B
609 610
L08D-X
Y11
602B
630
L08E-X
Y11
L08E-X
Y11
610
601A-B
601B
L08A-X
606-WS
604-R
603C
L08D
Y2-2
601B
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
BA-S1
L08A-X
606-WS
Y1
620
622
623B
603E
603C
604-L
Y5-1
603C
Y1
606-WS
Y3-1 Y3-2
607
607
622-L
Y6
Y2-1
601B
601B
602C
Y5-2
603C
L08B
Y1
606-WS
L08D
630
630
603C
602D
Y4-2
Y1
L08B-X
606-WS
BA-S1
DIAGRAM SHOWS THE ASSEMBLED
8X24 GRANDIO ELITE
THE BOX CONFIGURATION IS AN ELITE 8X8
PLUS (2) 8 FOOT EXTENSION KITS
606-WS
BA-S2
L08C-X
606-WS
AZ1
BA-S3
606-WS
602A
602A
602A
602A
603C/616
602A
Y7
Y7
602B
Y8
Y7
630
L08E-X
Outside View
606-WS
606-WS
602A
602A
L08C-X
606-WS
AZ1
BA-S3
606-WS
606-WS
606-WS
L08C-X
606-WS
610 609
L08D-X
609
BACK
In boxes GRA-ELI-8A and GRA-ELI-8P,
the base for 8x8 is all in GRA-BAS-8.
(8’ Extension Side) (GRA-ELI-8XA & GRA-ELI-8XP)
Elite 8’ Side Extension includes Base
8x8 Elite Side
(8’ Extension Side) (GRA-ELI-8XA & GRA-ELI-8XP)
Elite 8’ Side Extension includes Base
(8’x8’ Original Kit) (GRA-ELI-8A & GRA-ELI-8P & GRA-BA-8)
8x8 Elite Includes Front, Back, Base, and Sides
BASE KIT ASSEMBLY INSTRUCTIONS
Pre-Plan The Placement Of Your Structure
Allow enough room to get a wheel barrow in and around your structure.
Be sure the orientation will allow for proper drainage in and around your greenhouse.
It is recommended that you place your greenhouse in an area of your property that receives the most sunlight but is also somewhat protected
by trees, fencing or your home for wind protection and also to keep the temperature up during early spring and late fall.
The best placement depends on the features of your property, it is suggested in most scenarios to have your greenhouse face South on its
broadest side and to have the door face East or West depending on typical wind directions in your area. Do not worry if your orientation will
not allow for the placement to be as suggested, as a greenhouse that is facing North is better than no greenhouse at all.
Avoid building your greenhouse at the base of a slope as these are often frost pockets where cold air collects, this will not be good for your
greenhouse in keeping the temperature up inside.
Extreme Wind Conditions: If you live in a windy location there is no way to build a 100% storm safe greenhouse, but there are a number
of things you can do to minimize the chance of damage. Ensure that the base is level and square, be sure all panels are tightly in place and that
all aluminum extrusions are tight. The main problem is usually that wind gets into the greenhouse and the pressure pushes a panel out and
then the force of the wind on the interior causes more damage. It is best if you are expecting an extreme weather event that you disable any
auto roof vents and make sure all doors and windows are closed and locked shut. Also you may need to build a wind break for extreme condition areas where wind is constant and extreme.
It is ideal for your greenhouse to have water, electricity and even gas plumbed into place before construction. This will make watering plants
and keeping the temperature and air circulation to the max efficiency.
See pages 19 and 20 for installation methods below
For Cement Base Installation: We suggest you use wedge style concrete anchoring bolts to secure your structure.
For Deck Base Installation: We recommend you use a set of anchoring bolts to secure your structure.
For Earth Installation: We recommend you use the anchoring system provided and bury corner posts into the ground and seal into place
with quickrete.
11
BASE KIT PARTS LIST
GRAPHIC
PART NAME
SIZE/LOCATION
QUANTITY
BA-S1
97 3/8 in / 2474 mm
2
BA-S2
94/4 in / 2394 mm
BA-C3
GRAPHIC
SIZE/LOCATION
QUANTITY
BA-S5
46 3/4 in / 1187 mm
1
2
BA-S6
46 3/4 in / 1187 mm
1
5 7/16 in 138 mm
4
BA-C4
8 7/16 in / 214 mm
2
BA-A1
9 13/16 in / 250 mm
4
BA-A1
9 13 /16 in / 250 mm
2
BA-S03
M6*14
28
BA-S10
1/2 x 3/4
2
BA-M03
NUT
28
BA-S03
M6*14
16
W05
CLIPS
9
BA-M03
NUT
16
12
PART NAME
PARTS LIST FOR BASE KIT
(GRA-BA-4X) BASE AND ACCESSORY PACKING LIST
PARTS WILL BE FOUND IN (GRA-ELI-4X) BOX
(GRA-BA-8) BASE AND ACCESSORY PACKING LIST
PARTS WILL BE FOUND IN (GRA-BAS-8) BOX
BASE KIT PARTS LIST
(GRA-BA-8X) BASE AND ACCESSORY PACKING LIST
PARTS WILL BE FOUND IN (GRA-ELI-8XA) BOX
GRAPHIC
PART NAME
PARTS LIST FOR BASE KIT
SIZE/LOCATION
QUANTITY
BA-S3
93 7/16 in / 2374 mm
1
BA-S4
93 7/16 in / 2374 mm
1
BA-C4
8 7/16 in /214 mm
2
BA-A1
9 13/16 in / 250 mm
2
BA-S10
1/2 X 3/4
2
BA-S03
M6*14
16
BA-M03
NUT
16
13
8x12 BASE KIT ASSEMBLY INSTRUCTIONS
(GRA-BA-8) AND (GRA-BA-4X)
1.1 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front
BA-S5
and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front
BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1, see diagram .
1.2 Attach the BA-S2 to the BA-S5 with the BA-C4 using the BA-S03 and BA-M03.
See
. Repeat for other side connecting the BA-S6 and the BA-S2.
Go to page 18 for the next step.
ck
Ba
BA-S2
BA-C4
BA-S03
BA-M03
BA-C3
BA-S1
BA-C3
BA-A1
BA-S5
14
4”
BA-S10
BA-C4
BA-S6
BA-A1
BA-A1
BA-S2
BA-S10
BA-C4
BA-S2
BA-S1
BA-C3
BA-C3
nt
Fro
Note that the holes for
T I P screws on the base kit
sides have about a 2 foot gap between
each, so be sure base kit extensions
are assembled properly. See
.
GRANDIO
BA-A1
.5”
97
BA-A1
14
STEP ONE
BA-A1
8x16 BASE KIT ASSEMBLY INSTRUCTIONS
(GRA-BA-8) AND (GRA-BA-8X)
1.3 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front
BA-S3
and BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front
BA-S1. The BA-S3 and BA-S4 will attach to the back BA-S1. See diagram
.
1.4 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and BA-M03.
See
. Repeat for other side connecting the BA-S4 and the BA-S2.
Go to page 18 for the next step.
ck
Ba
BA-C4
BA-S03
BA-M03
BA-C3
BA-S1
BA-A1
BA-C3
BA-S3
BA-S4
191
.5”
BA-S10
BA-C4
BA-A1
BA-A1
BA-A1
STEP ONE
BA-S2
BA-S2
BA-C3
BA-S2
BA-S10
BA-C4
BA-S1
BA-C3
t
on
Fr
Note that the holes for
T I P screws on the base kit
sides have about a 2 foot gap between
each, so be sure base kit extensions
are assembled properly. See
.
GRANDIO
BA-A1
15
BA-A1
5”
.
97
8x20 BASE KIT ASSEMBLY INSTRUCTIONS
(GRA-BA-8) AND (GRA-BA-8X) AND (GRA-BA-4X)
1.5 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front
and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to the front
BA-S1. The BA-S5 and BA-S6 will attach to the back BA-S1. See diagram
.
1.6 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and BA-M03.
See
. Repeat for other side connecting the BA-S4 and the BA-S2, then BA-S3 to BA-S5
and BA-S4 to BA-S6.
Go to page 18 for the next step.
BA-S2
BA-C4
BA-S03
BA-M03
BA-C3
BA-S1
BA-C3
BA-S6
BA-S5
BA-A1 BA-S10
238
.5”
BA-C4
BA-A1
BA-S3
BA-A1
BA-S10
BA-C4
BA-A1
BA-S10
BA-C4
BA-S4
BA-A1
BA-S2
BA-S2
Note that the holes for
screws on the base kit
sides have about a 2 foot gap between
each, so be sure base kit extensions
are assembled properly. See
.
BA-S10
BA-C4
BA-A1
GRANDIO
TIP
BA-C3
BA-C3
BA-S1
BA-A1
16
t
on
Fr
5”
.
97
STEP ONE
ck
Ba
BA-S5
8x24 BASE KIT ASSEMBLY INSTRUCTIONS
(GRA-BA-8) AND (GRA-BA-8X) AND (GRA-BA-8X)
1.7 Layout all base kit pieces to prepare for assembly. Note that one BA-S1 will be at the front
and one BA-S1 will be at the back and the BA-S2’s will be on the sides attaching to front BA-S1.
The BA-S3 and BA-S4 will attach to the back BA-S1. The BA-S3 will attach to the other BA-S3
and BA-S4 will attach to the other BA-S4 See diagram
.
1.8 Attach the BA-S2 to the BA-S3 with the BA-C4 using the BA-S03 and BA-M03.
See
. Repeat for other side connecting the BA-S4 and the BA-S2, and then the BA-S3
to the BA-S3, and then the BA-S4 to the BA-S4.
Go to page 18 for the next step.
ck
Ba
BA-S5
BA-S2
BA-C4
BA-C3
BA-S1
BA-C3
BA-A1
BA-S3
BA-S4
BA-S10
BA-C4
BA-A1
286
”
BA-A1
BA-A1
BA-S10
BA-C4
BA-S3
BA-S4
BA-S10
BA-C4
BA-A1
BA-S2
BA-S2
STEP ONE
BA-S03
BA-M03
Note that the holes for
T I P screws on the base kit
sides have about a 2 foot gap between
each, so be sure base kit extensions
are assembled properly. See
.
BA-A1
GRANDIO
17
BA-S10
BA-C4
BA-C3
BA-C3
BA-S1
t
on
Fr
BA-A1
”
.5
97
BASE KIT ASSEMBLY INSTRUCTIONS
1.9 Slide the BA-C3 into the BA-S1, slide the BA-S2 into the BA-C3, align the holes and push together to an even and tight
position and use the BA-S03 Bolt and BA-M03 Collard Nut combo, tighten the collard nut on the inside of the base kit using the
10mm wrench. Repeat this process on all corners. See
and
.
Note: BA-S1 will be the front and back, while the BA-S2’ s will be the sides of your greenhouse base.
1.10 For Ground Installation only Insert the BA-S03 and the BA-A1 into the holes at the bottom side of the corners
of the base, the nut will be tightened on the inside of base. You will install the BA-A1 and the BA-S10 in the middle
where the extensions meet see
. If you are mounting your base kit to a flat mount surface like a deck or cement pad
discard the BA-S10 and BA-A1, you will need to purchase a fastener for your installation surface.
BA-S03
FRO
BA-S1
NT
BA-S2
BA-S1
E
SID
BA-C3
BA-S03
BA-S03
ML01
BA-S03
BA-C3
BA-M03 Collared Nut
BA-S3
BA-S2
BA-A1
BA-M03 Collared Nut
BA-A1
BA-C4
BA-S03
BA-M03
BA-S10
18
STEP ONE
BA-S2
BASE KIT GROUND INSTALLATION
**BASE MUST BE LEVEL & SQUARE,
FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY
1.11 BA-A1 must be buried in ground. See
.
Dig holes to bury the BA-A1’s, you determine size and depth for your location.
We recommend you use: Quikrete fast setting concrete to anchor base. Follow the directions on the package.
Outdoor
Ground
Assembly
BA-S2
Make sure base is squared
and level before setting
anchor into concrete. Use a measuring tape
to ensure all corners are the same. Use level
on all four sides.
BA-S1
GRANDIO
STEP ONE
TIP
BA-S03
BA-A1
19
BA-A1 * Must be inserted
into the ground, and secured
with concrete.
BASE KIT DECK INSTALLATION
**BASE MUST BE LEVEL & SQUARE,
FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY
1.12 Holes are present in base kit for anchoring bolts see
and
.
You determine and acquire proper fastener prior to installation for your surface.
Discard the BA-A1 and BA-S10 for deck or cement pad installation.
Use lag bolt
or concrete anchors
to attach base.
(Fasteners not included).
BA-S1
BA-S2
BA-S6
Deck or
Patio
Assembly
BA-S2
BA-C3
HOLE FOR ANCHOR
BOLT OR SCREW.
B
BA-C4
BA-S03
BA-M03
Use an appropriate fastener
to attach to your surface
through these access holes.
If surface is uneven you may want
to purchase large washers that
will fit under the base and allow
fasteners to go through to use as
a shim for leveling the base kit.
Make sure base is squared
and level before setting
anchors. Use a measuring tape to ensure all
corners are the same. Use level on all four
sides.
TIP
20
STEP ONE
GRANDIO
FRONT FRAME ASSEMBLY INSTRUCTIONS
ALWAYS ASSEMBLE FRONT HORIZONTAL
This picture shows the inside view of front section fully assembled.
All parts for front assembly will be found in box GRA-ELI-8A and GRA-ELI-8P.
We recommend that you assemble the front on a tarp.
* If you purchased the Back Door Transformation kit you will repeat this section for your
back wall using parts found in GRA-ELI-8A & GRA-ELI-BD boxes.
If you want to purchase the Back Door Transformation kit call 1-866-448-8231.
601B
601B
We recommend watching
our how to assembly videos
with tricks and tips for easier assembly and
installation of your Grandio Greenhouse at:
www.grandiogreenhouses.com
GRANDIO
Y3-2
601B
603E
TIP
Y3-1
601B
603D
Y2-2
603C
603C
STEP TWO
L08A-X
604-L
Y1
Y1
619
Inside View
606-WS
21
BOLT INSTALLATION TIP:
Locate all nuts and bolts, pre
thread and place in the groove of the
extrusion to make installation easier. Move
up or down for exact placement.
GRANDIO
L08A-X
604-R
606-WS
TIP
L08D
L08D
601A-FR
Lay flat on ground to
assemble the front frame of
your greenhouse. If possible try to find a
shady area protected from the wind. Panels
can burn grass and plants if in direct light.
GRANDIO
Y2-1
TIP
601A-FL
FRONT FRAME ASSEMBLY CONTINUED
ALWAYS ASSEMBLE FRONT HORIZONTAL
2.1 Prethread all S05 screws into the WG01
and WG02’s for ease of installation, see
only turn S05 a few turns.
S05
2.2 Use WG01 bracket to attach the (2)
WG01
601B
601B’s together with the 603E, secure parts
with the S05 screws provided see . The
WG01 will slide into the groove of the
601B’s, and also slide into the groove of the
603E, screw head will remain outside channel.
WG02
603E
2.3 Install WG02’s into (2) 601B’s then
tighten S05 screws when extrusions are
completely tight see
. Note: the fat end of
the WG02 will always be on the bottom side
see
.
601B
Inside View
PRETHREAD SCREWS TIP:
Locate all WG01, WG02,
and S05 screws, pre thread these to make
installation easier. Note that the fat end on
the WG02 will always face downward.
TIP
WG01
WG02
601B
601B
WG02
603E
FAT
END
FAT
END
601B
WG02
22
WG01
WG02
STEP TWO
GRANDIO
IMPORTANT: Use only S05 Screws, other screws may damage frame.
601B
601B
FRONT FRAME ASSEMBLY CONTINUED
ALWAYS ASSEMBLE FRONT HORIZONTAL
2.4 Insert polycarbonate panels Y3-2 and
Y3-1 into place as shown in
.
WG01
601B
2.5 Attach 603E and 603D with W04
and S04/ML01 fasteners as shown in
WG02
WG02
603E
.
2.6 Attach the 603D to the 601B’s
Y3-2
601B
using the W04-1’s with the S04/ML01
fasteners on both sides as shown in .
W04-1
603D
STEP TWO
IMPORTANT: POLYCARBONATE PANELS
Transparent Film
Polycarbonate
Panels
601B
Y3-1
W04-1
W04
Inside View
The UV-Protected side is covered with transparent film
and must face toward the sun. The side covered in white
film will always face the interior of the greenhouse. We
suggest you peel all film off completely prior to assembly and use a permanent marker to place a small “X” on
the lower right corner of each panel on the transparent
side that faces the sun, each panel has a sticker labeling
the panel number and this side always faces the sun or
outward as well. DO NOT REMOVE LABELS UNTIL
YOU INSTALL PANELS. The “X” is suggested in case
you dis-assemble your greenhouse in the future so you
may identify which side has the UV coating. Always use
gloves when handling the polycarbonate panels as the
edges can be very sharp.
Sun
601B
601B
S04
ML01
603E
W04
603D
W04
Opal White Film
23
W04-1
W04-1
603D
BOLT INSTALLATION TIP:
Locate ML01/S04 nuts and
screws, loosely pre thread into the W04 and
W04-1’s and place in the groove of the
extrusion to make installation easier.
GRANDIO
TIP
FRONT FRAME ASSEMBLY CONTINUED
ALWAYS ASSEMBLE FRONT HORIZONTAL
2.7 View diagrams and attach the (2) 604’s and (2)
601A’s to the 619. Note the orientation of the 604’s,
there are 4 different 601A’s (2) for the front and (2) for
the back with different hole placements. The large holes
should be at the top and facing forward on the front
frame assembly. See diagram on this page. The 601-FR
and the 601-FL will have a hole at the top side and will
face forward.
604-R
OUTSIDE
INSIDE
OUTSIDE
601A-FL
OUTSIDE
601A-FR
shows where the corner pieces attach to 619.
shows where the door frame attaches to the 619.
Inside View
INSIDE
INSIDE
619
*If assemblling the back door you will need to drill 1/4
inch holes in 601-B’s to match the front wall, these holes
should face the ground during assembly.
BOLT INSTALLATION TIP:
Locate all nuts and bolts, pre
thread and place in the groove of the
extrusion to make installation easier. Move
up or down for exact placement.
604-L
INSIDE
OUTSIDE
GRANDIO
TIP
TIP: If necessary you may use a screwdriver to wedge behind the bolt head.
601A-FR
619
ML01
Make sure the hole on the
601A-FL and 601A-FR
face to the front of greenhouse for future
install of the L21 and L28 bracket that
holds the door header in place.
604-R
ML01
S04
INSIDE DOOR FRAME
GRANDIO
TIP
S04
24
INSIDE
619
Inside View
STEP TWO
This prevents bolt from falling into the track.
FRONT FRAME ASSEMBLY CONTINUED
ALWAYS ASSEMBLE FRONT HORIZONTAL
2.8 Attach 606-WS to 619, this will hold the
polycarbonate panels in place. If it seems too
tight slide fingers or nut driver along edges,
gently stretching the 606-WS to allow room
for panels to fit .
Polycarbonate panel
OUTSIDE
606-WS
619
604-R
604-L
Y1
2.9 Insert Y1 polycarbonate panels into
place, make sure Y1’s slide completely into
606-WS as shown in .
Y1
601A-FL
601A-FR
2.10 Set (2) 603C’s atop the Y1 panels, then
606-WS
attach (2) L08D’s to the 603C’s, 601A’s and
604’s using S04/ML01 fasteners, make sure it
is snug with the tops of the Y1 panels, then
tighten fasteners. See .
619
Inside View
606-WS
STEP TWO
2.11 Insert the Y2-2 and Y2-1 polycarbonate
panels as shown in .
Y2-2
603C
L08D
GRANDIO
TIP
Polycarbonate
Panel
Transparent Film
Outside Greenhouse
Sun
601A
S04/
ML01
604
L08D
Y1
601A-FR
25
L08D
L08D
603C
Opal White Film
Inside Greenhouse
Y2-1
604-R
603C
601A-FR 604-R
603C
Y1
604-L 601A-FL
FRONT FRAME ASSEMBLY CONTINUED
ALWAYS ASSEMBLE FRONT HORIZONTAL
2.12 Move roof and front section together
WG02
601B
601A-FR
S05
601B
2.13 Attach the L08A-X to L08D and 604 to
square front section loosen S04/ML01
attached to the bottom of the (2) 604’s,
square the frame with carpenter square or use
a measuring tape to make sure corner measurements are the same, also check distance
across from the top of 601A’s, and also to the
bottom of the 601A’s across, make sure
distance is the same. Tighten L08A-X’s to hold
squareness as shown in .
W04-2
Fat End
UP
603D
S04
ML01
604
W04-2
603D
601B
W04-2
WG02
WG02
S05
S05
Y2-2
Y2-1
L08D
601A-FL
603C
Y3-1
Y3-2
L08D
S04
ML01
L08D
603C
603C
L08A-X
L08A-X
604-R
604-L
Y1
Y1
601A-FR
L08A-X
601A-FL
619
WG02
Profile View
26
Inside View
STEP TWO
and align the WG02’s into the 601A’s, and the
W04-2’s into the 604’s. Insure a snug fit
between the WG02’s, 601B’s and 601A’s and
then tighten the S05 screws as shown in
.
Tighten the W04-2’s with the S04 /ML01 nut
and bolt as shown in
.
BACK ASSEMBLY INSTRUCTIONS
ALWAYS ASSEMBLE BACK HORIZONTAL
This image shows the inside view of the back wall assembly.
All parts for back assembly will be found in box GRA-ELI-8A and GRA-ELI-8P.
We recommend that you assemble the back wall on a tarp.
* If you are using the Back Door Transformation Kit you will skip this section.
Inside View
601B
WG02
GRANDIO
TIP
Transparent Film
Outside Greenhouse
STEP THREE
Opal White Film
Inside Greenhouse
Y5-2
Y4-2
Make sure the UV coated
GRANDIO
T I P side of the panel faces
outward as indicated on the panels. Avoid
placing the polycarbonate panels in the sun
or near plants until fully assembled.
BOLT INSTALLATION TIP:
T I P Locate all nuts and bolts, pre
thread and place in the groove of the
extrusion to make installation easier. Move
up or down for exact placement.
601B
Y5-1
602C
602D
602D
Y4-1
WG02
WG02
GRANDIO
WG02
WG01
Sun
601B
Polycarbonate
Panel
601B
L08B
603C
603C
Y1
Y1
603C
603C
Y1
L08B-X
Y1
L08B-X
601A
601A
606-WS
27
L08A
606-WS
BACK CONTINUED
ALWAYS ASSEMBLE BACK HORIZONTAL
WG01 and WG02, see
FAT
END
FAT
END
.
3.2 Use the WG01 bracket to attach the
WG02
(2) 601B’s together, secure parts by
sliding the WG01 into the 601B’s as
shown in diagram
.
3.3 Install WG02’s to connect (2) 601B’s
WG01
WG02
S05
601B
when firmly placed between the extrusions tighten the S05 screws, see
.
WG01
601B
WG02
601B
STEP THREE
3.1 Prethread all S05 screws into the
601B
IMPORTANT: Be careful moving or you may bend bracket.
601B
WG02
601B
WG01
Inside View
601B
WG02
PRETHREAD SCREWS TIP:
Locate all WG01, WG02,
and S05 screws, loosely pre thread these to
make installation easier. Note that the fat
end on the WG02 will always face down.
GRANDIO
TIP
601B
28
BACK CONTINUED
ALWAYS ASSEMBLE BACK HORIZONTAL
3.4 Attach (2) 601A-B’s to L08A using S04/ML01
fastener as shown in diagram
.
Attach (2) 602D’s to L08A using S04/ML01 fasteners
as shown in diagram
.
Attach 602C to L08A using S04/ML01 fastener as
shown in diagram
.
Y1
3.5 Attach the (4) 606-WS’s to the L08A as shown
STEP THREE
in
.
3.6 Insert the Y1 polycarbonate panels into the
Y1
Y1
602D
601A-B
grooves of 601A, 602D and 602C. Make sure Y1
panels are inserted into 606-WS as shown in
. You
may need to use a screwdriver to gently open the
606-WS to fit the polycarbonate panels into the
groove of 606-WS.
Y1
602D
601A-B
602C
606-WS
606-WS
606-WS
606-WS
L08A
602D
601A
602C
Polycarbonate Panel
L08A
ML01
S04
ML01
INSIDE
INSIDE
L08A
L08A
29
S04
606-WS
L08A
BACK CONTINUED
ALWAYS ASSEMBLE BACK HORIZONTAL
3.7 Set (4) 603C’s atop each Y-1 panel, then align the
pre threaded S04-ML01 fasteners in each 603C to the
L08B and to each 601A-B, 602D and the 602C.
When aligned tighten the middle first and work your
way outward. See diagrams
,
, .
Y4-2
3.8 Insert the Y5-1 and Y5-2 polycarbonate panels
Y5-2
Y5-1
Y4-1
into place. Then insert the Y4-1 and Y4-2 into place as
shown in the diagram.
603C
Y1
Y1
602D
603C
Y1
601A-B
602D
602C
Inside View
603C
601A-B
L08B
603C
L08B
603C
603C
L08B
ML01
602D
S04
30
602D
L08B
602C
STEP THREE
Y1
601A-B
603C
603C
L08B
BACK CONTINUED
ALWAYS ASSEMBLE BACK HORIZONTAL
WG01
3.9 Pre thread the S05 screws on WG01, WG02’s
and the S04/ML01 W04-2’s brackets and place
into appropriate extrusion see
,
and
.
Align WG02’s into 601A’s, the W04-2’s into
602D’s, and the WG01 into the 602C. When all
members are snug tighten all fasteners to lock into
place.
W04-2
601B
601B
601B
STEP THREE
601B
602C
602D
WG02
W04-2
Y4-2
602D
Y5-2
Y5-1
Y4-1
601A-B
601B
WG02
601A-B
WG02
601A-B
Y1
BOLT INSTALLATION TIP:
Locate all nuts and bolts, pre
thread and place in the groove of the
extrusion to make installation easier. Move
up or down for exact placement.
Y1
Y1
GRANDIO
TIP
Inside View
31
Y1
BACK CONTINUED
ALWAYS ASSEMBLE BACK HORIZONTAL
3.10
A. Attach (2) L08B-X’s to (2) 602D’s and
L08A with S04/ML01 as shown in .
B. Attach (2) L08B-X’s to the (2) 601A-B’s
with fasteners as shown in
.
L08B-X
601A-B
602D
602C
602D
STEP THREE
S04/ML01
602D
L08B-X
L08A
Inside View
L08B-X
L08B-X
ML01
S04
Square by loosening bolts
T I P attached to the tops of the
L08B-X, use measuring tape to make sure
corners to corner measures the same.
601A-B
601A-B
GRANDIO
32
MIDDLE ASSEMBLY INSTRUCTIONS
Warning: The person(s) holding the front or back sections vertical must continue to do so until the L08C-X angle supports
are attached securely to the front and base as shown in step 4.5. Failure to hold front vertical will cause the front to fall and
damage the base kit, front framing etc. Damage caused by improper installation is not warrantable.
STEP FOUR
If building a greenhouse with a front and
back door you will repeat steps 4.1-4.5 for
attaching both front and back walls of the
greenhouse.
4.1 We recommend pre threading all (9) W05
clips with the nut and bolt combos now. See ,
note the bolt head will always slide into the extrusion, W05 clips will be used in step 4.5.
601A
BA-S1F
ML01
S04
BA-S2
ML01/
NUT
W05
CLIP
S04 BOLT
Inside View
Front Right side
4.2 With no less than 2 people place the pre
assembled front section on top of the base kit front.
Have person (1) hold the front vertically while the
other attaches the front section 601A’s to the base
using S04/ML01 fasteners as shown in .
Person (1) must continue to hold up the front wall!
BA-S5
BA-S1
BA-S6
**This Base shows a 8x12, your
greenhouse may be longer and
configured of more base kit pieces.
604
1
601A
BA-S2
601A
You will need a minimum of
(2) people to complete the
middle assembly of your greenhouse. The
more people the merrier at this stage of
assembly.
GRANDIO
TIP
2
BA-S1
33
MIDDLE ASSEMBLY CONTINUED
4.3 Attach L08C-X to 601A and the BA-S2 with S04/ML01 on both sides as shown in
and
combos.
4.4 Attach the front section 619 to the base using (3) S04/ML01 fasteners as shown in
to the inside of the 619 with (5) self tapping screws included in the package, see .
with the nut and bolt
, then attach the threshold support
601A
L08D
L08C-X
604
STEP FOUR
601B
1
L08A-X
Threshold
Support
will attach
with 5 self
tapping
screws
601A
L08C-X
601A
2
619 Attaches to the
base kit with S04/ML01
BA-S1
Base
34
MIDDLE ASSEMBLY CONTINUED
4.5 Have person (1) continue to hold the front vertically while the other attaches the font section to the base with
W05/S04/ML01 fasteners as shown in
,
and
. The (4) W05 clips will catch the under edge of the front base kit and
then slide upward attaching to the bottom of the 601A’s and the 604’s. You will slide the bolt into the extrusion, slide it down to
catch the edge of the base kit, then slide up and hold up as high as it will go and then tighten the ML01 nut, note you will have
to switch out the combo that was originally used to the W05 Clip.
STEP FOUR
If you are using the Back Door Transformation kit you will repeat steps 4.1-4.5 to install the Back Door Wall.
W05
619
BA-S1
Base
BA-S1
Inside
BA-S5
BA-S6
1
604
604-R
601A
L08A-X
619
W05
ML01
S04
601A
BA-S2
601A
BA-S1
ML01
S04
BA-S2
2
BA-S1
W05
Inside View
35
MIDDLE ASSEMBLY CONTINUED
If you are using the Back Door Transformation kit you will repeat steps 4.1-4.5 to install the Back Door Wall, then
skip ahead to step 4.9.
4.6 Attach back wall 601A’s with back base corners using S04/ML01 on both sides as shown in
4.7 Attach bottom of L08C-X to rear section of base kit with S04/ML01, as shown in
as shown in
, make sure the S04/ML01 combos are tight.
.
. Attach the L08C-X to the 601A
4.8 Use the (5) remaining W05 clips to attach the backwall where the 601A’s meet the corner of the base as shown in ,
and where 602D’s, and the 602C meet the BA-S1B see
. Then use W05 Clip combos to attach the corner 601A’s to
the base kit as shown in , you will have to switch out the combo that was originally used to the W05 Clip.
601A
ML01
S04
BA-S2 or
BA-S6
BA-S1
Inside View
Back Left side
601A
L08B
L08C-X
602C
STEP FOUR
601B
L08B-X
L08C-X
602D 602D
W05
L08C-X
602C, 602D
Outside
Inside
L08C-X
Bac
kB
601A
BA-S1
ML01
S04
BA-S2 or
BA-S6
Back Wall
Base
Bac
k Ba
W05
Inside View
36
se
ase
Base
MIDDLE ASSEMBLY CONTINUED
4.9 Attach the 607 to 607 extension with the
607-XS and the (4) S08 screws provided see
,
.
The S08 screws are to be installed on the inside as
shown in diagram . Wait to tighten the screws all at
one time when both sections are aligned correctly,
apply even pressure while tightening.
607-XS
607
S08
STEP FOUR
4.10 Apply a bead of silicone to the seam where
the 607’s meet and to the holes where the S06
screws will attach the DP01 to the 607 ridge.
See
. Immediately align the DP01 apply a
smallamount of silicone to the holes on the
exterior of DP01 then insert the S06 screws.
607
607
607-XS
For 8x20 and 8x24 Grandio Elite Assembly
DP01
Repeat these steps if you are building an 8x20
or 8x24 with your last extension box, note it is
best to connect 8x8, then 8X, then an 4X if
assembling an 8x20. Note that the notches
shown in
should be spaced every 2 feet,
none should be right next to each other.
NT
O
FR
607
S06
WARNING
607
S06
T
ON
FR
607
Notches
Notches
DP01
APPLY SILICONE CAULK
TO RIDGE AND HOLES
37
MIDDLE ASSEMBLY CONTINUED
4.11 With 2 people, attach the ridge to front and back by sliding into place as
Side Angle View
shown in
and
, using S04/ML01 fasteners attach the 607 to the 601B’s.
See
for how the final orientation should be.
601B
607
601B
Inside View
607
601B
601B
Inside View
S04/ML01
601B
38
607
601B
STEP FOUR
607
EXTENSION ASSEMBLY INSTRUCTIONS
STEP FIVE
Warning: You will need a minimum of 2 people to complete this section, you will not be able to stop assembly until page
45. Note that if you are assembling an 8x20 or an 8x24 greenhouse you will proceed thru the 2nd extension assembly instructions. Damage caused by improper installation is not warrantable. It will be helpful to prepare and lay each section and
necessary parts out prior to beginning this sections actual assembly, pre reading will make this section much easier.
Warning: This section will take about 30 minutes so be prepared to finish as there is not a stopping point until page 45 for
an 8x12 or 8x16 Greenhouse, or for an 8x20 or 8x24 Greenhouse page 50. Note it may be helpful to have a few more people at
this point the more the merrier.
BOLT INSTALLATION TIP:
Locate about 30 nuts and
bolts and pre thread for easiest installation.
GRANDIO
TIP
39
EXTENSION ASSEMBLY INSTRUCTIONS
5.1 Connect the (2) braces labeled L08M-X / L08C-X together with the
5.2 Attach the 602A to the base with a nut and bolt combo where the
extension kits meet on the base kit, with other person holding the 602A
in place. Measure down 6” from the top of the 602A to attach the W14
bracket to the 602A on both sides with the S04/ML01 . See
and
.
Attach the assembled L08M-X’s to the W14 as shown in
and .
L08M-X
L08M-X
This part is labeled with 2
stickers L08C-X and L08M-X.
We will refer to this part as
L08M-X in all instances
moving forward.
5.3 Attach (2) L08D-X’s to the 602A and to the base using the
ML01/S04 Combos. See
and
Back
602A
.
L08M-X
602A
Measure 6”
W14 BRACKET
STEP FIVE
nut and bolt combo S04/ML01 see
. The combined L08M-X’s should
measure about 94 1/2” when connected together.
W14
6”
602A
W14
607
L08D-X
L08M-X
IMPORTANT TO HAVE THE L08M-X
FACE THE BACK AS SHOWN
L08D-X
Measure 6”
L08D-X
602A
L08D-X
BA-S2
BA-S2
Bac
k
BASE
Fro
nt
40
EXTENSION ASSEMBLY INSTRUCTIONS
5.4 Attach the 609-XS to 609 with the (2) S09 screws provided
INSIDE VIEW
STEP FIVE
see
. The S09 screws are to be installed from the outside of
the 609, see
.
609-XS
Pay special attention to the orientation of the 609, make
sure the correct side faces down, see
.
UP
FRONT
Profile View
OUTSIDE VIEW
Groove
609
609
UP
UP
609-XS
S09
41
FRONT
EXTENSION ASSEMBLY INSTRUCTIONS
5.5 With 2 people proceed to install 609 in this
Inside View
Inside View
LOOSEN
ML01
1. With one person holding the 609 level and in position
have the other person loosen the top of the L08C-X and
let it fall free, attach the 609 to the 601B using S04/ML01
(nut and bolt). See
and
.
L08C-X
601B
601B
609
601A
L08D
S04/ML01
L08D
L08C-X
2. Now move the loosened S04/ML01 (nut and
601B
bolt) currently attached to the L08C-X upward to
secure the 609, 601A-F and L08C-X together
601B
as shown in
.
601A
L08B
3. Have assistant keep holding at the middle
section . Turn to next page for detailed
installation.
601A
L08C-X
2
601A
Profile View
1
601B
Note the line on the
609 that shows the
exact placement of UP
the 601B’s and the
601A’s when installed
correctly.
Groove
609
601A
L08C-X
L08C-X
L08D
601A
L08C-X
You will need a minimum of
T I P (2) people to complete the
middle assembly of your greenhouse. The
more people the merrier at this stage of
assembly.
GRANDIO
42
L08D
601A
STEP FIVE
order, note that 609 must be installed with groove
side down see
.
EXTENSION ASSEMBLY INSTRUCTIONS
STEP FIVE
4. Note the top of 602A should touch the line on the 609 for
exact placement, see
. Attach the 609 to the 602A with the
S04/ML01 nut and bolt combos see diagram
.
5. Repeat steps 1-4 on the other side see
.
NOTE EXACT PLACEMENT OF
THE 602A TO THE 609.
609
609
602A
EXACT
PLACEMENT
LINE FOR 602A
OUTSIDE VIEW
609-XS
FRO
NT
602A
602A
609
S04/ML01
FRONT
INSIDE VIEW
602A
43
EXTENSION ASSEMBLY INSTRUCTIONS
5.6 Moving up to the midroof 609, with person 1 holding the 609 in place person 2 will attach the 609 to the front of the
.
STEP FIVE
greenhouse to the 601B’s, see
. Person 1 will continue holding the 609.
5.7 Person 2 will attach the 602B to the 609’s see . Attach one more 602B between the 609 and 607, see
Repeat on the other side of greenhouse
Inside View
FRONT
609
Inside View
607 Roof Line
602B
FRONT
601B
ML01/S04
602B
609
609
601B
609
1
ML01/S04
602B
2
602A
609
609-XS
Outside View
607 Roof Line
607
602B
EXACT
PLACEMENT
** 8x16 Elite Shown
44
609
FRONT
EXTENSION ASSEMBLY INSTRUCTIONS
5.8 With two people attach the AZ-1 to the base and the lower 602A, see
STEP FIVE
. Next attach the upper end to
the mid roof line touching the 609 see
for exact placement. Install on both sides of the greenhouse where
the extension seams meet using the S02/ML01 combo.
5.9 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof as shown between the
(2) 602B’s. Note the exact placement of the edge of the BZ-1 should touch the top edge of the 609 see
.
601B
BZ-1
S04
ML01
609
AFTER COMPLETING STEP 5.9
609-XS
IF YOUR GREENHOUSE IS AN 8X12
OR 8X16 SKIP TO PAGE 51. IF
YOURS IS AN 8X20 OR 8X24
PROCEED ON TO THE NEXT PAGE.
AZ-1
BZ-1
AZ-1
602B
AZ-1 Bracket
UP
S02
ML01
607
AZ-1
UP
2
INSIDE VIEW
602A
602A
609
AZ-1
S02/ML01
You will need to
switch this bolt
out to an S02
1
t
on
Fr
S02/ML01
AZ-1 BRACE
(longer edge touches
bottom of interior base kit)
** 8x16 Elite Shown
45
601B
Front
609
609
S02
ML01
2nd EXTENSION ASSEMBLY INSTRUCTIONS
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
the nut and bolt combo S04/ML01 see
. The combined L08M-X’s
should measure about 94 1/2” when connected together.
5.11 Attach the 602A to the base with a nut and bolt combo
Measure down 6” from the top of the 602A to attach the W14 bracket
to the 602A on both sides with the S04/ML01 . See
and
.
Attach the assembled L08M-X’s to the W14 as shown in
and .
This part is labeled with 2 stickers
L08C-X and L08M-X
W14 BRACKET
5.12 Attach (2) of the L08D-X supports to the 602A and to the base
using the ML01/S04 Combos. See
and
L08M-X
L08M-X
602A
.
6”
Measure 6”
L08M-X
STEP FIVE
5.10 Connect the (2) braces labeled L08M-X / L08C-X together with
Back
602A
L08M-X
W14
602A
W14
L08D-X
L08D-X
L0DX
1
IMPORTANT TO HAVE THE L08M-X
FACE THE BACK AS SHOWN
602A
L08D-X
BA-S2
Measure 6”
Bac
k
BASE
Fro
nt
46
2nd EXTENSION ASSEMBLY INSTRUCTIONS
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
STEP FIVE
5.13 Attach the 609-X to 609 with the (2) S09 screws provided
INSIDE VIEW
see
. The S09 screws are to be installed from the outside of
the 609, see
.
609-XS
Pay special attention to the orientation of the 609, make
sure the correct side faces down, see
.
UP
FRONT
Profile View
Groove
UP
OUTSIDE VIEW
609
609
UP
609-XS
S09
47
FRONT
2nd EXTENSION ASSEMBLY INSTRUCTIONS
5.14 With 2 people proceed to install 609 extension at the eave
GAP FOR SCREWS 609
or lower mid roof in this order.
609
1. With one person holding the 609 level and in position have the other
person attach the 609 to other end of the 609-XS as shown in
.
2. With one person holding the 609 level and in position have the other
person attach the 609 to the 602A using S04/ML01. See
.
S09
3. Repeat steps 1. and 2. on other side of the greenhouse.
F2RON
T
609-XS
609-XS
609-XS
NOTE EXACT PLACEMENT OF
THE 602A TO THE 609.
609-XS
2
609
1
609
1
1
UP
EXACT
PLACEMENT
LINE FOR 602A
602A FRON
T
48
609
STEP FIVE
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
2nd EXTENSION ASSEMBLY INSTRUCTIONS
STEP FIVE
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
5.15 With person 1 holding the 609 in place person 2 will attach the 609 to the 609-XS with the (2) S09’s screws to the upper
mid roof see
. Person 1 will continue holding the 609.
5.16 Person 2 will attach the 602B to the two 609’s with (2) S04/ML01 (nuts and bolts) see . Attach one more 602B
between the 609 and 607 with (2) S04/ML01 (nuts and bolts), see
.
Repeat both steps on the other side of greenhouse.
GAP FOR SCREWS 609
609
602B
609
F2RON
T
609-XS
S09
1
2
Outside View
Inside View
FRONT
602B
609
607
602B
EXACT
PLACEMENT
ML01/S04
602B
1
607 Roof Line
609-XS
609
FRONT
49
2nd EXTENSION ASSEMBLY INSTRUCTIONS
CONTINUE FOR 8X20 AND 8X24 ONLY / FOR 8X12 AND 8X16 SKIP AHEAD TO PAGE 51 OR STEP 5.19
. Then
attach the upper end to the mid roof line touching the 609 see
for exact placement.
Install on both sides of the greenhouse where the extension seams meet using the
S02/ML01 combo.
601B
BZ-1
S04
ML01
609
5.18 Install the BZ-1 to the upper mid roof, to act as the support to the peak of the roof
as shown between the (2) 602B’s. Note the exact placement of the edge of the BZ-1
should touch the top edge of the 609 see
.
609-XS
AZ-1
S02
ML01
601B
BZ-1
602B
FRONT
602A
609
2
AZ-1
AZ-1
FR
1
ON
T
S01/ML01
AZ1 BRACE
(longer edge touches
bottom of interior base kit)
50
609
STEP FIVE
5.17 With two people attach the AZ-1 to the base and the lower 602A, see
MIDDLE BACK ASSEMBLY INSTRUCTIONS
5.19 With two people attach the 609 extension to 609-XS with the
(2) S09 screws provided see
and
601B
STEP FIVE
5.20 With person 2 still holding in place have person 1 loosen the
S04/ML01
L08B
L08C-X
601B
Repeat these steps on other side of the
greenhouse, and then mid roof line see
609
609
L08C-X nut and bolt combo, allow to fall out of place, then align the
609 into place with the 601B and 601A, see
. Use a S04/ML01
combo to attach the 609 to the 601B, then slide the nut and bolt
combo attached to the L08C-X into place to secure the 609
between the 601A and the L08C-X.
INSIDE VIEW
ML01/S04
601B
601A
. 609
601B
609
609
609-XS
607
609
609
1
FRONT
ML01/S04
602A
OUTSIDE VIEW
609
601A-B
2
609
609
2
S09
INSIDE VIEW
Inside View
.
FRONT
609-XS
51
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
of the greenhouse you will need to loosen the
ML01 (nut) attached to the L08C-X and the
base. See diagram . Remove and set aside
the L08D-X supports.
1. Once the bottom of one L08C-X is loosened
set the 602A onto the bolt of the L08C-X. Be
sure the 602A is aligned and sitting flush on top
of the base kit. See
for reference.
Inside View
602A
609
602A
ML01/S04
ML01/S04
L08C-X
BA-S2
BASE
602A
3. Repeat steps 1. and 2. on all four corners
where the L08C-X ‘s meet the base kit.
4. Now attach the bottom of 602A to the
Base using a S04/ML01 (nut and bolt) as
shown in
, and to the 609 with an
S04/ML01 combo as is shown in
.
5. Repeat step 4. on all places where a
602A should go. You may reference
diagrams at front for your exact size.
Loosen only one L08C-X at a time.
L08C-X
L08D-X
602A
602A
602A
602A
L08D-X
L08C-X
602A
L08C-X
Note: Where the L08C-X reattaches to the
BASE and the 602A be sure to secure
them tightly see
.
52
S04
ML01
Inside View
Inside View
2. Hold the 602A in place and attach the top of
the 602A to the 609 using S04/ML01 (nut
and bolt). As shown in
.
C-X
L08 e
e
c
d
i
a
Sl o pl
int
STEP FIVE
5.21 Before you attach the 602A’s to the sides
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
STEP FIVE
5.22 Install only the upper roof line 602B’s
Outside View
between the 607 and the 609 along the entire
upper roof line with S04/ML01 (nut and bolt).
See
and
. Repeat on other side of roof
section.
607
602B
Do Not attach lower roof 602B’s yet, they will
get in your way when installing the upper roof
panels and roof vents.
602B
609
Polycarbonate
Panel
Transparent Film
Outside Greenhouse
TOP
609
607
609
TIP
602B
EXACT
PLACEMENT
ML01
S04 TOP
GRANDIO
Roof Line
Sun
Opal White Film
Inside Greenhouse
53
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
slide the 630 into the groove of the upper 609 as
607
shown to hold Y11’s in place. See
and
. Note
630
that you may need to loosen the bottoms of some of
Y11
the 602B’s to slide the 630’s into place as the fit is
609
Y11
very tight. Check that all nut and bolt combos are
tightened again after installation of 630’s. Note that
601B
there is a 630 in the extension box(s), make sure you
install so the screw holes on the 630’s align for the
DP03 to attach. Once the 630’s are aligned apply a
streak of silicone to the seam of the 630’s, then align
the DP03 with the holes and affix into place with the
S06 screws provided. See
.
601B
602B
602B
Y11
APPLY SILICONE CAULK
TO RIDGE AND HOLES
602B
602B
Y11
Y11
DP01
Right Side of Greenhouse
Is Shown in Image
602B
601B
Y11
630
601B
S06
630
BACK
FRONT
The two profiles should be flush
at ends when installed correctly.
630
630
601B
601B
601B
609
609
609
The two profiles should be flush
at ends when installed correctly.
630
630
601B
609
Left Profile View
Right Profile View
54
STEP FIVE
5.23 Insert Y11 panels to upper roof section then
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
STEP FIVE
5.24 Assemble the roof window vents as shown below in
and
,
using the Z02 screws attach the 615, 616, and 618’s with the Y10
panel as shown, be careful not to strip the screw heads. Pay attention
to the Y10 panel, as the stickers must face the sun.
630
Y10
5.25 Insert assembled window into the end of the ridge of 630 and
slide into position. See
. Window positions are your discretion
however, must be in the middle for support, do not place nearest the
front or back as you will need a 602B support to keep in window
vent in place. Place directly across from each other for best cross
draft ventilation, see
for optional placement.
616
Z02
618
Roof Vent
Placement
Y10
Y10
SUN
Z02
616
615
PC sheet
Roof Vent
Z02
Inside
Screwdriver
SUN
615
618
Place roof windows in
T I P desired location before
attaching all 602B’s. Note and 8x12 has 3
windows, an 8x16 has 4 windows, an 8x20
has 5 windows and 8x24 has 6 windows.
630
Note Correct Orientation
Inside of window
Z02
Outside View
Z02
Y10
GRANDIO
616
618
Z02
55
602B
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
5.26 Attach all remaining 602B’s between the 609’s,
after all roof vents are positioned see .
5.27 Install plastic strip 606-WS before inserting
.
5.28 After Y7’s are installed on both sides, loosen
bolts attached to L08C-X in all upper corners.
Using a level, adjust 602A and tighten bolts.
Repeat in every corner until the greenhouse is
plumb. The top edges of Y7’s will align when
greenhouse is level or plumb.
STEP FIVE
polycarbonate sheet Y7’s, see
Y11
Y11
Y11
Y10
Outside View
607
EXACT
PLACEMENT
Y11
Y10
602B
609
602A
602A
Polycarbonate Panel
Outside
602B
Y11
606-WS
606
BASE
56
Y11
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
5.29 To ensure there is no gap in roof vent
STEP FIVE
616
Inside view of 603C
603C
position 603C as shown in
. Connect
603C to middle of 602B’s using W04
bracket as shown in
.
602B
5.30 Attach HQC01 to 616 with the Z04
screws see
, close roof vent and attach
the handle onto HQC02 middle pin (the
first two holes of the handle to the second
and third pins of HQC02). Then attach
HQC02 into 603C’s track with S04/ML01
(nuts and bolts), see
.
618
603C
616
W04
603C
HQC02
603C
Y10
Note: If you are installing automatic roof vent openers
follow those directions for correct installation.
SAVE MANUAL HARDWARE FOR WINTER SWITCHOUT.
Y10
HQC01
Handle
Y10
HQC01
Handle
HQC01
Handle
HQC01
Handle
Z04
HQC02
616
603C
57
ML01/S04
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
5.31 Remove the L08M-X support combo, take apart
and use as L08C-X now and install on the sides of the
AZ1 extension brace, as shown in . Note that the
L08C-X and L08M-X have been labeled with both
stickers in this instance as this part has 2 uses. Save the
hardware and W14 bracket for possible future use or
hang inside as a plant hanger clip.
5.33 Slide 610 Gutters into 609’s
groove as shown in diagram
. Repeat
on both sides. Note the orientation of the
gutters, the extension gutters will be at
the back and the holes should align with
gutter down spout hole see next page.
Outside View
610
601A
Y11
L08C-X
Y11
Y11
Y10
Y11
Y11
Y9
Y10
L08M-X
Y11
Y9
AZ1
TAPE
Y8
Y8
L08C-X
610
Gutter
The two profiles should be flush
at ends when installed correctly.
609
L08M-X
609
58
STEP FIVE
5.32 Insert polycarbonate sheets Y8’s and Y9’s
into the lower roof of your greenhouse. Panels
may slide out before gutters are in place. You
may want to place a piece of tape on the
panel to prevent sliding as shown in the
Y8
diagram once the panels are in place.
601B
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
STEP FIVE
5.34 Apply a small amount of the silicone caulk to the seam
610
where the 610 gutters meet, then attach the DP02 on the inside
of the gutter and the DP02B will slide under the gutter and will
rest above the 602A. Apply silicone to the holes where the S07
screws will attach the 610 gutters to the DP02 and DP02B.
Note the DP02B has pre-tapped holes to accept the screws and
hold tight. See diagram
and .
DP02
DP02B
Repeat these steps to assemble the additional set(s) for both
sides of your greenhouse.
Remove the tape from the panels you may have used to hold in
place.
610
602B
DP01
610
610
602A
59
MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED
5.34 Attach JG01, JG02A, JG02B, JG03A and JG03B end caps to the ridge,
JG01
JG02A
JG02B
STEP FIVE
midroof and gutters on both front and back as shown below. Squeeze a small
amount of rubberized silicone into the ends of ridge, mid roof, and gutters to secure
pressure fit end caps, as shown in the images to the right. Use Z03 screws to attach
the JG03A and JG03B endcaps along with the silicone adhesive.
JG03A
JG01
JG02B
JG03B
JG03B
Z03
JG02A
JG03A
Z03
60
The two profiles should be flush
at ends when installed correctly.
STEP SIX
DOOR ASSEMBLY DIAGRAM
This image shows the inside view of Right Door Assembly.
All parts for door assembly will be found in box GRA-ELI-8A and GRA-ELI-8P.
Use the #2 head Phillips Screw Driver for installation.
If you are using the Back Door Transformation kit you will repeat steps 6.1-6.11 to install the Back Door,
these parts will be found in box GRA-ELI-BD.
622-R
623A
622
Side View
Z01
Y6
623A
Side View
622-R
UP
Z01
622
UP
Double
Ball Catch
620
Y6
620
Z01
Z01
UP
UP
Z01
623B
623B
Z01
J08A
Bottom
View
Inside View
622
Bottom
View
622
J08A
J08A
J08A
61
We recommend you lay out all parts for both doors to make sure they match up correctly for hanging. Double check the orientation of what is inside verses outside and how the doors will hang on page 63-67. Make sure window panels face the right direction
to the sun and note that the panels have predrilled holes for the handles to attach later and these need to be aligned with the lock
mechanisms. This will save you from assembling the wrong way. Be careful not to strip the phillips heads when assembling.
6.1 Insert J08A into the bottom of the 622, note the bottom groove is smaller than the top groove of 622, see .
6.2 Use the Z01 screws to attach the 622 to the 623B, 623A and 620 as shown in .
6.3 Insert Y6 windows into position as shown in .
623A
623A
623A
FLUSH
ALIGN
WITH TOP
Z01
You may need to gently open
the channel with a flat head
screwdriver if screws are not
going into place with ease.
622
Side View
622
Z01
622
620
620
UP
Y6
623B
Z01
UP
Bottom
View
J08A
620
Y6
623B
623B
Inside View
622
GRANDIO
TIP
Transparent Film
Outside Greenhouse
J08A
Polycarbonate
Panel
62
Opal White Film
Inside Greenhouse
Sun
STEP SIX
DOOR ASSEMBLY
STEP SIX
DOOR ASSEMBLY CONTINUED
6.4 Insert J08A into the bottom of the 622-R and 622-L, note the bottom has a groove see .
6.5 Attach the 622-L to the 623B, 623A and 620 using the Z01 screws as shown in .
6.6 Follow the same instructions for the other door making sure that the 622-L and 622-R with the double ball catch match up
so doors will latch closed and slide properly
.
Z01
Side View
Of Top
622-L
* Double
Ball Catch
on the 622-L
623A
Side View
Of Top
622-R
Double
Ball Catch
622-R
* Note the orientation of
the 622-L and 622-R.
Also make sure the right
side is facing out on the
Y6 polycarbonate panels.
UP
* Double
Ball Catch
on the 622-R
UP
Y6
UP
Z01
620
622-R
UP
Side View
Of Bottom
Bottom
View
J08A
622
Side View
Of Bottom
Y6
622
Z01
623B
Inside View
J08A
63
6.7 Slide the (2) S02 bolts down the track of the L21 see
, align with the holes on the 603D door header. With one person
inside the greenhouse line up hanging door track L21 with door header 603D, move bolts on L21 to line up with bolt holes on
door header 603D. From the inside hand tighten the ML01 nut while the person outside is holding the L21 in position, you will
now center on the front of the greenhouse and tighten the S02/ML01 combo.
S02
603D
L21
1
2
S02
SCREW
ck
a
Tr
Inside View
Side Profile View of
L21 Hanging Track
64
STEP SIX
DOOR INSTALLATION
STEP SIX
DOOR INSTALLATION
6.8 Separately slide the top of the doors in the left and right side of L21, see diagram
, until they latch in the middle.
6.9 Attach the door handles 622-HNDL to both doors using the 622-HNDL-NUT/BOLT provided to both doors as shown
below in
, and
.
**We included some felt dots in your Grandio Welcome Kit, please apply to the inside bottom edge of the 623B as shown in
these felt dots will make your doors fit snug and slide smoothly.
L21
S04
S02
L21
Top
Bottom
Outside View
623B
623B
Inside View
622-HNDL
622-HNDL
622-HNDL
NUT/BOLT
Side Profile View
of Hanging Track
65
622-HNDL
NUT/BOLT
,
S04
STEP SIX
DOOR INSTALLATION
6.10 Attach L28 to L21 with S04/ML01, and L28 to
601A with S02/ML01 as shown below in diagram
and
. Check that the L21 and L28’s are square.
Attach (2) J07 to the ends of L21 see
. The L28
should align square to the 601A.
6.11 Check that the door locks are snug, you may
adjust them with screwdriver if needed as they can be
tightened or loosened.
603D
S04/ML01
L28
601A-FR
L21
Top Left
Profile View
J07
Backside View
601A
L21
S02
L28
S02
ML01
L28
601A-FL
Top Profile View
66
601A
INTERIOR ROOF SUPPORT ASSEMBLY
7.1 Attach the L08E-X to the upper roof section
609
as shown with S04/ML01 fasteners already in
place where the 607 meets the 601B, and the
609 and the 602B meet see , repeat this on
the front section of the greenhouse, and where
extensions meet at the AZ-1.
7.2 Attach the L08D-X to the rear lower roof
section where S04/ML01 fasteners are already
in place where the 609 and the 602B meet, and
the 609 and the 601B meet see
, repeat on
the front section, and where the extensions
meet the AZ-1.
607
BZ-1
609
L08E-X
601B
L08D-X
CZ-1
601B
L08D-X
9”
9”
602B
7.3 Attach the BZ-1’s to the roof line as shown
609
in diagram
with the S04/ML01. The edge of
the BZ-1 should meet up to the edge of 609
exactly.
Roof
Vent
607
BZ-1
7.4 Use CZ-1’s to support the interior wall at
602B
the eave using the S04/ML01. See diagram
.
We suggest that you measure down 9” and mark
it with a pencil so the base of the CZ-1 will meet
there.
STEP SEVEN
CZ-1
CZ-1
601B
L08E-X
L08D-X
601B
You may remove all stickers now with Goo
Gone remover if needed.
Congratulations You Did It!!
67
(GRA-ELI-8A) 8x8 GRANDIO ELITE ALUMINUM PACKING LIST
PART NAME
GRAPHIC
PART NAME
SIZE/LOCATION
QUANTITY
SIZE/LOCATION
QUANTITY
56 9/16 in / 1437 mm
2
604-R
70 3/4 in / 1797 mm
FRONT RIGHT
1
FRONT LEFT CORNER
1
604-L
70 3/4 in / 1797 mm
FRONT LEFT
1
601A-FR
56 9/16 in / 1437 mm
1
607
94 1/4 in / 2394 mm
1
601B
29 7/16 in / 748 mm
8
606-WS
21 3/4 in / 553 mm
14
602A
56 9/16 in / 1437 mm
6
609
94 1/4 in / 2394 mm
4
602B
29 7/16 in / 748 mm
12
610
94 3/8 in / 2397 mm
2
602C
90 1/2 in / 2299 mm
1
615
22 3/4 in / 578 mm
2
602D-R
83 1/4 in / 2115 mm
1
616
22 3/4 in / 578 mm
2
602D-L
83 1/4 in / 2115 mm
1
618
19 11/16 in / 500 mm
4
603C
21 7/8 in / 555 mm
8
630
94 3/8 in / 2397 mm
2
603D
72 3/16 in/ 1833 mm
1
L08A
94 1/4 in / 2394 mm
1
94 1/4 in / 2394 mm
1
601A-B
601A-FL
BACK CORNERS
56 9/16 in / 1437 mm
FRONT RIGHT CORNER
CORNER ROOF
NOTE THESE ARE
PACKED TOGETHER
603E
18 1/4 in / 463 mm
1
619 PACK
THRESHOLD BAR
AND SCREW
94 1/4 in / 2394 mm
1
L08B
68
PARTS LIST FOR GRA-ELI-8A
GRAPHIC
(GRA-ELI-8A) 8x8 GRANDIO ELITE ALUMINUM PACKING LIST
PARTS LIST FOR GRA-ELI-8A
GRAPHIC
PART NAME
SIZE/LOCATION
QUANTITY
GRAPHIC
PART NAME
SIZE/LOCATION
QUANTITY
L08D
24 3/16 in / 614 mm
2
Z03
M3*25
4
L08A-X
52 1/4 in / 1327 mm
2
S02
M6*20
6
L08B-X
51 3/16 in / 1300 mm
2
ML01/S04
M6*14
150
L08C-X
61 1/32 in / 1550 mm
4
S05
SCREWS FOR WG01 AND WG02
M6*10
45
L08D-X
37 13/16 in / 960 mm
4
Z04, S04/ML01
ROOF VENT HARDWARE
4
L08E-X
38 11/16 in / 957 mm
4
HQC01
ROOF VENT ARM
2
WG01
FRONT & BACK
2
HQC02
ROOF VENT LATCH
2
WG02
FRONT & BACK
8
L28
19 9/16 in / 497 mm
2
W04
ROOF LINE
5
W11
SCREW DRIVER
1
W04-1
BACK WALL
2
W13
MULTI-DRIVER
1
W04-2
CONNECTOR
4
W16
10 MM NUT DRIVER
1
Z01
M4*30
SCREWS FOR DOORS
13
BZ-1
56 1/2 in / 1435 mm
3
Z02
M4.6*16
SCREWS FOR ROOF VENTS
9
CZ-1
23 5/8 in / 600 mm
6
69
(GRA-ELI-8A) 8’x8’ GRANDIO ELITE ALUMINUM PACKING LIST
PART NAME
SIZE/LOCATION
QUANTITY
GRAPHIC
PART NAME
SIZE/LOCATION
10
QUANTITY
622-HNDL
DOOR HANDLES
4
S10
M6*16
ATTACHES 619 TO BASE
10
622-HNDL
NUT/BOLT
DOOR HARDWARE
4
JG01
RIDGE END CAP
2
620
21 7/16 in / 545 mm
2
JG02 A/B
MID ROOF END CAP
2/2
L21
95 1/2 in / 2425 mm
1
JG03 A/B
GUTTER END CAP
2/2
J07
L21 END CAP
2
622
69 11/16 in / 1770 mm
2
622-L
69 11/16 in / 1770 mm
1
622-R
69 11/16 in / 1770 mm
1
623A
21 7/16 in / 545 mm
2
623B
21 7/16 in / 545 mm
2
J08A
DOORS
4
PARTS LIST FOR GRA-ELI-8A
GRAPHIC
70
(GRA-ELI-8P) 8’x8’ ELITE PANEL BOX PACKING LIST
PARTS LIST FOR GRA-ELI-8P
GRAPHIC
NAME
SIZE/LOCATION
WIDTH
HEIGHT 1
HEIGHT 2
QTY
Y1
FRONT & BACK PANEL
22 3/4 in / 578 mm
47 5/16 in / 1202 mm
Y2-1
FRONT PANEL
22 3/4 in / 578 mm
9 1/16 in / 230 mm
23 in / 585 mm
1
Y2-2
FRONT PANEL
22 3/4 in / 578 mm
23 in / 585 mm
9 1/16 in / 230 mm
1
Y3-1
FRONT PANEL
35 1/2 in / 902 mm
9 15/16 in / 252 mm
19 1/8 in / 486 mm
1
Y3-2
FRONT PANEL
35 1/2 in / 902 mm
19 1/8 in / 486 mm
9 15/16 in / 252 mm
1
Y4-1
BACK PANEL
22 3/4 in / 578 mm
9 1/16 in / 230 mm
35 3/16 in / 894 mm
1
Y4-2
BACK PANEL
22 3/4 in / 578 mm
35 3/16 in / 894 mm
9 1/16 in / 230 mm
1
Y5-1
BACK PANEL
22 3/4 in / 578 mm
35 7/16 in / 900 mm
42 13/16 in / 1087 mm
1
Y5-2
BACK PANEL
22 3/4 in / 578 mm
42 13/16 in / 1087 mm
35 7/16 in / 900 mm
1
Y6
DOOR PANEL
22 3/4 in / 578 mm
34 in / 864 mm
4
Y7
SIDE WALL PANEL
22 3/4 in / 578 mm
57 in / 1447 mm
8
Y8
ROOF PANEL
22 3/4 in / 578 mm
30 5/8 in / 778 mm
6
Y9
UNDER ROOF VENT
22 3/4 in / 578 mm
8 7/8 in / 225 mm
2
Y10
ROOF VENT PANEL
22 3/4 in / 578 mm
19 1/8 in / 486 mm
2
Y11
ROOF PANEL
22 3/4 in / 578 mm
30 3/8 in / 772 mm
8
71
6
(GRA-ELI-4X) ELITE 4’ EXTENSION ALUMINUM PACKING LIST
PART NAME
SIZE/LOCATION
QUANTITY
602A
56 9/16 in / 1437 mm
4
610
46 3/4 in / 1187 mm
2
602B
29 7/16 in / 748 mm
8
DP02
GUTTER BRACKET
2
603C
21 7/8 in / 555 m
1
DP02B
GUTTER BRACKET
2
L08C-X / L08M-X
61 in / 1550 mm
2
630
46 3/4 in / 1187 mm
2
L08D-X
37 13/16 in / 960 mm
2
615
22 3/4 in / 578 mm
1
L08E-X
37 11/16 in / 957 mm
2
616
22 3/4 in / 578 mm
1
607
46 3/4 in / 1187 mm
1
618
19 11/16 in / 500 mm
1
607-XS
ROOF CONNECTOR
1
AZ-1, S02/ML01
86 1/4 in / 2190 mm
EXTENSION SUPPORT
2
DP01
ROOF CONNECTOR
1
BZ-1
56 1/2 in / 1435 mm
ROOF SUPPORT
2
609
46 3/4 in / 1187 mm
4
CZ-1
23 5/8 in / 600 mm
EAVE SUPPORT
2
609-XS
EAVE CONNECTOR
4
Z02
5X12 MM
SCREWS FOR ROOF VENT
5
DP03
630 CONNECTOR
2
S04 / ML01
M6*14
50
606-WS
21 3/4 in / 553 mm
4
S06
4*10
ATTACHES DP01 TO 607
3
GRAPHIC
72
PART NAME
SIZE/LOCATION
QUANTITY
PARTS LIST FOR GRA-ELI-4X
GRAPHIC
(GRA-ELI-4X) ELITE 4’ EXTENSION ALUMINUM PACKING LIST
GRAPHIC
PART NAME
PARTS LIST FOR GRA-ELI-4X
S07
SIZE/LOCATION
QUANTITY
M5*8
SCREW FOR DP02 AND DP02B
5
S08
M6*16
ATTACHES 607-XS TO 607
5
S09
M4*6
ATTACHES 609-XS TO 609
20
W04
CONNECTOR FOR 603C
2
W14
L08M-X BRACKET
2
W15
LARGE WASHER
NOT FOR USE IN THIS UNIT
2
HQC01
ROOF VENT ARM
1
HQC02
ROOF VENT LATCH
1
Z04, S04/ML01
ROOF VENT HARDWARE
4 EACH
73
4X ELITE 4’ EXTENSION PANEL BOX PACKING LIST
NAME
SIZE/LOCATION
WIDTH
HEIGHT 1
HEIGHT 2
QTY
Y7
SIDE WALL PANEL
22 3/4 in / 578 mm
57 in / 1447 mm
4
Y8
ROOF PANEL
22 3/4 in / 578 mm
30 5/8 in / 778 mm
3
Y9
UNDER ROOF VENT
22 3/4 in / 578 mm
8 7/8 in / 225 mm
2
Y10
ROOF VENT PANEL
22 3/4 in / 578 mm
19 1/8 in / 486 mm
1
Y11
ROOF PANEL
22 3/4 in / 578 mm
30 3/8 in / 772 mm
4
74
PARTS LIST FOR GRA-ELI-4X
GRAPHIC
(GRA-ELI-8XA) ELITE 8’ EXTENSION ALUMINUM PACKING LIST
PARTS LIST FOR GRA-ELI-8XA
GRAPHIC
GRAPHIC
PART NAME
SIZE/LOCATION
QUANTITY
PART NAME
SIZE/LOCATION
QUANTITY
602A
56 9/16 in / 1437 mm
8
610
94 1/4 in / 2374 mm
2
602B
29 7/16 in / 748 mm
16
DP02
GUTTER BRACKET
2
603C
21 7/8 in / 555 m
2
DP02B
GUTTER BRACKET
2
L08C-X / L08M-X
61 in / 1550 mm
2
630
93 7/16 in / 2374 mm
2
L08D-X
37 13/16 in / 960 mm
2
615
22 3/4 in / 578 mm
2
L08E-X
37 11/16 in / 957 mm
2
616
22 3/4 in / 578 mm
2
607
93 7/16 in / 2374 mm
1
618
19 11/16 in / 500 mm
4
607-XS
ROOF CONNECTOR
1
AZ-1
86 1/4 in / 2190 mm
EXTENSION SUPPORT
2
DP01
ROOF CONNECTOR
1
BZ-1
56 1/2 in / 1435 mm
ROOF SUPPORTS
4
609
93 7/16 in / 2374 mm
4
CZ-1
23 5/8 in / 600 mm
EAVE SUPPORTS
6
609-XS
EAVE CONNECTOR
4
Z02
M4.6*16
SCREWS FOR ROOF VENTS
9
DP03
630 CONNECTOR CAP
2
S04 / ML01
M6*14
90
606-WS
21 3/4 in / 553 mm
8
S06
M4*10
ATTACHES DP01 TO 607
3
75
(GRA-ELI-8XA) 8X GRANDIO ELITE ALUMINUM PACKING LIST
PART NAME
S07
SIZE/LOCATION
M5*8
SCREW FOR DP02 AND DP02B
QUANTITY
5
S08
M6*16
ATTACHES 607-XS TO 607
5
S09
M4*6
ATTACHES 609-XS TO 609
20
W04
CONNECTOR FOR 603C
4
W14
L08M-X BRACKET
2
W15
LARGE WASHER
NOT USED IN THE UNIT
2
HQC01
ROOF VENT ARM
2
HQC02
ROOF VENT LATCH
2
Z04, S04/ML01
ROOF VENT HARDWARE
4
PARTS LIST FOR GRA-ELI-8XA
GRAPHIC
76
(GRA-ELI-8XP) GRANDIO ELITE 8 EXTENSION PANEL BOX PACKING LIST
PARTS LIST FOR GRA-ELI-8XP
GRAPHIC
NAME
SIZE/LOCATION
WIDTH
HEIGHT 1
HEIGHT 2
QTY
Y7
SIDE WALL PANEL
22 3/4 in / 578 mm
57 in / 1447 mm
8
Y8
ROOF PANEL
22 3/4 in / 578 mm
30 5/8 in / 778 mm
6
Y9
UNDER ROOF VENT
22 3/4 in / 578 mm
8 7/8 in / 225 mm
2
Y10
ROOF VENT PANEL
22 3/4 in / 578 mm
19 1/8 in / 486 mm
2
Y11
ROOF PANEL
22 3/4 in / 578 mm
30 3/8 in / 772 mm
8
77
GRAPHIC
PART NAME
SIZE/LOCATION
QUANTITY
603D
72 3/16 in / 1833 mm
SIZE/LOCATION
QUANTITY
1
Z01
M4*30
SCREWS FOR DOORS
13
603E
18 1/4 in / 463 mm
1
ML01/S04
M6*10
35
70 3/4 in / 1797 mm
1
ML01/S02
M6*20
4
604L
70 3/4 in / 1797 mm
1
L21
95 1/2 in / 2425 mm
1
L08D
24 3/16 in / 614 mm
2
J07
L21 ENDCAP
2
619
94 1/4 in / 2394 mm
1
L28
19 9/16 in / 497 mm
FRONT RIGHT
2
622
69 11/16 in / 1770 mm
2
W04
CONNECTOR BRACKET
1
622R
69 11/16 in / 1770 mm
1
W04-1
FRAME CONNECTOR
2
622L
69 11/16 in / 1770 mm
1
W04-2
FRAME CONNECTOR
2
620
21 7/16 in / 545 mm
2
Y3-1
UPPER ROOF PANEL
1
623A
21 7/16 in / 545 mm
2
Y3-2
UPPER ROOF PANEL
1
623B
21 7/16 in / 545 mm
FRONT RIGHT
2
Y2-1
BACK WALL SIDE
L08A-X
52 1/4 in / 1327 mm
CROSS SUPPORT
2
Y2-2
BACK WALL SIDE
1
J08A
DOOR
4
Y6
DOOR PANELS
4
622-DOOR
HANDLES
DOOR HANDLES
4
604R
BACK WALL
BACK WALL
FRONT RIGHT DOOR
FRONT LEFT DOOR
GRAPHIC
78
PART NAME
1
PARTS LIST FOR GRA-ELI-BD
(GRA-ELI-BD) GRANDIO ELITE BACKDOOR PACKING LIST
Grandio Greenhouse Limited Lifetime Warranty
1. Grandio Greenhouses are warranted to the original purchaser to be free from defects in material or workmanship for ten years from the
date of original retail purchase on all plastic panels. Additionally the aluminium frame is warranted for life. The word “defects” is defined as
imperfections that impair the use of the product.
WARRANTY
2. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installation, alteration of accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the
control of the manufacturer.
3. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product if the product is defective within
the terms of this warranty, Grandio Greenhouses will repair or replace defective parts at no cost to the purchaser. Shipping charges to and
from the factory or distribution center are not covered and are the responsibility of the purchaser. Labor charges and related expenses for
removal, installation or replacement of the greenhouse or its components are not covered under this warranty.
4. This warranty does not cover scratching or scuffing of the product that may result from normal usage. In addition, defects resulting from
intentional damage, negligence, unreasonable use will void this warranty.
5. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the
highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use
of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.
6. This product is not intended for institutional or commercial use; Grandio Greenhouses does not assume any liability for such use.
7. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability for use to extent
permitted by Federal and State Law. Neither Grandio Greenhouses nor any representative assumes any other liability in connection with this
product. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
79
NOTES
NOTES
GRANDIO
G R E E N H O U S E S
2015 Grandio Elite 8x12, 8x16, 8x20 & 8x24 Models
GREENHOUSE USER MANUAL
KEEP IN A SAFE PLACE FOR REFERENCE
CONTACT US IF YOU NEED HELP
OR
HAVE MISSING OR DAMAGED PARTS
GRANDIOGREENHOUSES.COM
BACKYARD LIVING SOURCE, INC.
9543 W. EMERALD ST., SUITE 101
BOISE, ID 83704
1-866-448-8231
Related documents
Grandio Greenhouses ELITE-8 Use and Care Manual
Grandio Greenhouses ELITE-8 Use and Care Manual
GREENHOUSE USER MANUAL
GREENHOUSE USER MANUAL
GREENHOUSE USER MANUAL
GREENHOUSE USER MANUAL
grandio greenhouse user manual
grandio greenhouse user manual
BACK WALL TRANSFORMATION USER MANUAL GRA-ELI-BD
BACK WALL TRANSFORMATION USER MANUAL GRA-ELI-BD
GREENHOUSE USER MANUAL
GREENHOUSE USER MANUAL
GREENHOUSE USER MANUAL
GREENHOUSE USER MANUAL
GREENHOUSE USER MANUAL
GREENHOUSE USER MANUAL
BACK WALL TRANSFORMATION USER MANUAL GRA-ELI-BD
BACK WALL TRANSFORMATION USER MANUAL GRA-ELI-BD
BACK WALL TRANSFORMATION USER MANUAL GRA-ELI-BD
BACK WALL TRANSFORMATION USER MANUAL GRA-ELI-BD
Benq 5J.J3C01.001 rechargeable battery
Benq 5J.J3C01.001 rechargeable battery