Download Ultra ElectronicS Prima 3 User's Manual

Operation (continued)
User mode settings
Main menu
Submenu
Factory setting
4 counter type settings: [Total, Head, Free, Rollers]
Total
>>Counter
>Display>
To t a l
Display mode
See p. 30
>>Contrast
0(Standard)
OK?
>Cleaning>
YMCK:0
0(Standard)
>>Black Mode
Standard
See p.32
>>UV MAC Adr Pos
Upper Right
0(Standard)
> > M e d i a Ty p e
>Retransfer>
Std(1000/roll):0
Retransfer mode
> > Te m p . L e v e l
0(Standard)
See p. 33
>>Speed (Front)
+2(Fast)
Upper Right
9 levels of density setting –3 to +5, the
larger the value the darker the printing.
Setting the special ink SP-Ink2 level:
9 gradations can be set from –3 to +5, the larger the value the darker the printing.
Setting the retransfer film: setting the film type
[1000,750] - two types
Setting the retransfer roller temperature:6 gradations can be set from –3 to +2,
the larger the value the higher the
temperature.
Setting the retransfer speed: 13 gradations can be set from –10 to +2,
the larger the value the faster the speed.
Setting the rear retransfer speed:
>>Speed (Back)
+2(Fast)
13 gradations can be set from –10 to +2, the
larger the value the faster the speed.
>>MG Print(JIS)
Off
>>Standby mode
==
Front Wait
Setting the way of peeling off the retransfer film: 2 settings [On and Off]
Laminate Standby selection: In case of both side printing with optional unit connected,
select either one of the card sides for standby.2 Settings [Front Wait, Back Wait]
Buzzer mode
Setting the buzzer ON/OFF: 2 settings [on and off]
>Buzzer
See p. 34
On
>Bend Remedy>
Bend Remedy
mode
See p. 35
Power saving mode
See p. 34
Setting the time for the power saving mode:9 options [off, 5, 10, 15, 20, 25, 30, 45 and
60] (units: minutes)
Bend remedy roller temperature setting: 7 gradations can be set from –5 to 0 or
> > Te m p . L e v e l
off, the larger the value the higher
Off
the temperature.
>>Speed
Bend remedy speed setting: 5 gradations can be set from –2 to +2, the
+2
larger the value the faster the speed.
Cooling time setting:
>>Cooling Time
None
>Card Thickness
Standard
> M G I S O Ty p e
Hi-Co
>IC Antenna Pos.
None
>IC Contact Pos.
None
> Te s t P r i n t
OK?
28
16 gradations can be set: none and 1–15 (units
seconds).
Card thickness setting mode:
See p. 36
Card thickness setting: 2 options [Standard, Thin]
Coercivity setting mode:
See p. 36
ISO card coercivity setting:
2 options [Lo-Co
and Ho-Co]
Non-contact IC antenna setting mode:
Non-contact IC antenna position setting: 3 options [None, Ext. Unit, Added on]
IC contact position setting mode:
IC contact position setting: 3 options [None, Built-in, Ext. Unit]
Test print mode:
to carry out test printing:
press the ENTER button.
0
Standard
(1000/roll):0
+1
+2
+2
Off
Front Wait
On
Off
+2
None
Standard
Hi-Co
See p. 36
See p. 36
See p. 36
+3
On
On
>Power Saving
0
Standard
Setting of MAC address position in the case of UV print
[Upper Right, Lower Left]
+3(Thick)
>>SP-Ink2 Level
9 gradations can be set from –3 to +5, the
larger the value the darker the printing.
Setting the K printing mode: 2 options [standard and fine]
UV ink level setting:
>>UV Level
See p. 31
Display on ink ribbon : the ink type being used is displayed
Display only because of automatic setting by RF-ID(Setting is not possible)
Setting the black level K:
>>Black Level
Ink mode
0
PURPLE
LCD panel background color setting: 8 options
Counter reset mode
See p. 31
For free counter resetting: press the ENTER button.
Cleaning mode
For cleaning mode setting: Magnetic head and card feeder roller execution
> > I n k Ty p e
>Ink>
7 gradations from –3 to +3, the higher
the value the stronger the contrast.
>>Back Color
PURPLE
>Counter Reset
LCD panel contrast setting: