Download Therma-Tru Light Commercial Doors and Frames User's Manual

Therma-Tru® Light Commercial/Multi-Family - Doors and Frames
• Material shown on these drawings will be
fabricated only after formal approval by the
architect, receipt of approval hardware schedule,
and all necessary hardware templates.
• All frames shall be shipped “knocked-down”
unless otherwise specified.
GENERAL NOTES
• All frames and doors shall be chemically washed,
rinsed, and dried prior to receiving one coat of
paint.
• Doors and frames will be reinforced for surface
mounted hardware as required. Drilling and
tapping for surface mounted hardware shall be
applied by others.
DOOR HANDING CHART
SINGLE DOORS
SINGLE DOORS
OUTSIDE
OUTSIDE
LEFT HAND INSWING
RIGHT HAND INSWING
• Installations of all glass and glazing to be
performed by others.
OUTSIDE
OUTSIDE
LEFT HAND REVERSE/
LEFT HAND REVERSE
RIGHT HAND OUTSWING
RIGHT HAND REVERSE/
RIGHT HAND REVERSE
LEFT HAND OUTSWING
PAIRS
OF
DOORS
PAIRS
OF DOORS
PAIRS
OF DOORS
OUTSIDE
OUTSIDE
OUTSIDE
• Anchor bolts and expansion shields for any type
fastener to be furnished by others.
OUTSIDE
RIGHT HAND ACTIVE
RIGHT HAND ACTIVE
• It will be the responsibility of the General
Contractor to coordinate hardware locations.
OUTSIDE
• All frames will be supplied with rubber door
silencers: three for single swing openings and two
per header for double swing openings.
RIGHT HAND REVERSE
RIGHT
ACTIVE
HAND REVERSE ACTIVE
OUTSIDE
OUTSIDE
• All frames will be supplied with the required wall
and floor anchors as illustrated on the frame detailLEFT HAND REVERSELEFTACTIVE
HAND REVERSE ACTIVE
sheet.
LEFT HAND REVERSE ACTIVE/
RIGHT HAND OUTSWING ACTIVE
JOB NUMBER:
RECORD OF SUBMITTALS
SUBMITTED
RETURNED
PROJECT:
1st
2nd
3rd
4th
RECORDED APPROVED DRAWINGS
RECORDED APPROVED HARDWARE
DRAWN BY:
ARCHITECT:
CONTRACTOR:
FINISHED HARDWARE BY:
• Field welding, grinding, finishing, and attachment
of field splices by others.
SHEET NUMBER:
OUTSIDE
RIGHT HAND REVERSE ACTIVE/
LEFT HAND OUTSWING ACTIVE
LOCATION:
• These drawings are not intended for use by other
trades.
• Doors, frames, and finished hardware to be
installed by others.
• All frames must be set absolutely plumb, square,
and level.
LEFT HAND ACTIVELEFT HAND ACTIVE
• All frames and doors wll be tagged with shop
marks. This schedule can be used to cross
reference shop marks with architects marks.
• All standard type hardware will be located at this
manufacturer’s standard locations as shown on
the door and frame elevations. Hardware items
such as panic exit devices, deadbolts, etc. will also
be located at manufacturer’s standard locations
unless specifically advised.
OF
JOB NUMBER
ARCH MARK
QUANTITY
ITEM
FROM
TO
SWING
PROJECT
GAUGE
WIDTH HEIGHT
SHEET NUMBER
SECT.
SHEET
OF
HRDWR. SET/ HDG.
FLUSH BOLTS
CLOSER
LOCK
ELEV.
DOOR DATA
HINGE
LABEL
SHEET
GAUGE
FRAME DATA
DOOR CONSTR.
ANCHOR
OVERALL HEIGHT
JAMB DEPTH
ELEV.
DOOR OPENING
SHEET
DOOR THICK.
LOCATION
FRAME CONSTR.
Therma-Tru® Light Commercial/Multi-Family - Schedule
HARDWARE
REMARKS
LOCATION
Therma-Tru® Light Commercial/Multi-Family - 22-Gauge & 24-Gauge Steel Doors
DOOR ELEVATIONS - FLUSH - LITED
EXPOSED GLASS
SIZE: 4” x 25”
EQUAL 10” EQUAL
EQUAL
22”
EQUAL
EQUAL
22”
EQUAL
EXPOSED GLASS
SIZE: 5” x 20”
EXPOSED GLASS
SIZE: 10” x 10”
EXPOSED GLASS
SIZE: 22” x 28”
STYLE# SE960HD
STYLE# SE969HD
STYLE# SE978HD
34”
28”
20”
25”
33”
EXPOSED GLASS
SIZE: 3” x 33”
5”
10”
4”
3”
EXPOSED GLASS
SIZE: 22” x 34”
DOOR ELEVATIONS - EMBOSSED - OPAQUE
STYLE# SE210HD
STYLE# 514
STYLE# 500
Therma-Tru® Light Commercial/Multi-Family - FG Doors
DOOR ELEVATIONS - SMOOTH
STYLE# SSF100
STYLE# SSF160
STYLE# SSF200
STYLE# SSF960
DOOR ELEVATIONS - GRAINED
STYLE# FCF100
STYLE# FCF140
STYLE# FCF160
Therma-Tru® Light Commercial/Multi-Family - Standard Hardware Preps.
4" x 4" HINGE DETAIL
STANDARD LATCH PREP
LATCH PREPS
BENCHMARK
STEEL
ENTRANCE
BENCHMARK
STEEL
ENTRANCE
DOOR. DOOR
.097
.097(12
(12GA.)
Ga.)
2.040
2.040
DEADBOLT
ASSEMBLY
DEADBOLT
ASSEMBLY
45 1/4"
FROM
OF
DOOR
45 1/4"
FROMTOP
TOP OF
DOOR
5 1/2" STANDARD
5 1/2" STANDARD
DEADBOLT
FILLER
DEADBOLT
FILLER
PLATEPLATE
.500
.500
1.500
1.500
44447/8"
TOP
DOOR
7/8"FROM
FROM TOP
OF OF
DOOR
2.500
2.500
3.500
3.500
3.985
3.985
#10 flat head screw
DEADBOLT
HOLE:
DRILLEDBLOCK.
THROUGH
WOOD
THROUGH WOOD BLOCK.
44 7/8" FROM TOP OF DOOR
DEADBOLT HOLE: DRILLED
DRILL
DIA.
Drill .295/.300
.295 / .300
Dia.
COUNTERSUNK
Countersunk FOR
for aA #10
FLAT HEAD SCREW.
5 1/2" STANDARD
5/8"
5/8"RAD.
Rad.
5 1/2" STANDARD
4.080
4.080
44 7/8" FROM TOP OF DOOR
.018
.018
NOTE: ALL DIMENSIONS ARE
TYPICAL ON BOTH SIDES.
Note: All dimensions
are typical on both
sides
.375
.375
1.062
1.062
STEEL
DEADBOLT
PREP
STEEL
DEADBOLT
PREP:
STAMPED1 11/18"
1/8" x x2 3/4"
OPTIONAL
STAMPED
2 3/4"
OPTIONAL
DEADBOLTPREP
PREP FOR
FOR STEEL
DEADBOLT
STEELFRAMES.
FRAMES.
AVAILABLE WITH ADJUSTA-FIT,
AVAILABLE
WITHHOLLOW
ADJUSTA-FIT,
ADJUSTA-TRIM,
METAL,
ADJUSTA-TRIM,
& SECURA-FIT
SECURA-FIT & VISTA
III FRAMES.
FRAMES.
STANDARD 1 1/18" x 2 1/4"
STRIKE WITH OPTIONAL
1 1/18"STANDARD
x 2 1/4"DEADBOLT
1 1/8" x 2 1/4" STRIKE w/ PREP.
OPTIONAL 1 1/8" x 2 1/4" DEADBOLT PREP
LATCH
FILLER
LATCH
FILLERPLATE
PLATE
1 1/4" x 8" MORTISE LOCK PREP.
NOTE: MORTISE LOCK IS NOT
OFFERED WITH LANDMARK
1 1/4" x 8" MORTISE LOCK PREP
DOORS.
* NOTE: MORTISE LOCK
KNOB
LATCH
KNOB
LATCH
IS NOT OFFERED WITH
LANDMARK DOORS.
STEEL TEE STRIKE PREP
STEEL LIP STRIKE PREP
STEEL 4 7/8" ANSI PREP
STAMPED
STRIKE
PREP
STAMPED
TEETEE
STRIKE
PREP
FORFOR
STEEL
STEEL AVAILABLE
FRAMES. WITH
AVAILABLE
w/
FRAMES.
ADJUSTAFIT,ADJUSTA-FIT,
ADJUSTA-TRIMADJUSTA-TRIM,
& SECURA-FIT
HOLLOW METAL & SECURA-FIT
FRAMES.
STAMPED
LIP STRIKE
PREP
FOR
STAMPED
LIP STRIKE
PREP
FOR
STEEL
STEELAVAILABLE
FRAMES. AVAILABLE
w/
FRAMES.
WITH ADJUSTAADJUSTA-FIT, ADJUSTA-TRIM,
FIT, ADJUSTA-TRIM
& SECURA-FIT
SECURA-FIT & VISTA III FRAMES
FRAMES.
STAMPED 44 7/8"
STAMPED
7/8" ANSI
ANSISTRIKE
STRIKEPREP
PREPFOR
S T E STEEL
E L F RFRAMES.
A M E S . AVAILABLE
AVA I L A B L E w /
FOR
ADJUSTA-FIT,
ADJUSTA-TRIM,
HOLLOW
WITH
ADJUSTA-FIT,
ADJUSTA-TRIM
&
METAL & SECURA-FIT FRAMES.
SECURA-FIT FRAMES.
Therma-Tru® Light Commercial/Multi-Family - Hardware Locations
STANDARD STEEL ENTRANCE DOORS
HARDWARE LOCATIONS
YOUR REP. FOR MORE INFO.
NOMINAL WIDTH (FRAME OPENING)
NOMINAL FRAME OPENING WIDTH
NOTE: BASE FRAME = 16-GA.
9 7/8”
NOTES:
FLOOR
HINGE BACKSET = 5/32"
2-0
23 11/16"
2-4
27 11/16"
2-6
29 11/16"
6-8
78 5/8"
45 1/4"
44 7/8"
7-0
82 1/8"
45 1/4"
44 7/8"
8-0
93"
59 5/8"
59 1/4"
2-8
31 11/16"
UNDERCUT OPTIONS:
STANDARD - 1 3/4"
DOORS UNDER 6-8 OR
OVER 7-0 ARE AVAILABLE.
CONTACT YOUR REP. FOR
MORE INFO.
STANDARD 1 3/4" DOOR, HINGE and CYLINDER LOCK LOCATIONS:
DOOR HEIGHT
NOMINAL
ACTUAL
MORTISE PREP
CYLINDRICAL PREP
30”
SQUARE EDGE
22 GA. = .027 MIN.
24 GA. = .023 MIN
DOOR WIDTH
NOMINAL
ACTUAL
30”
30"
30"
1 3/4" UNDERCUT STANDARD
2 3/8" OR 2 3/4"
BACKSET (STD.)
STRIKE LOCATION
NOMINAL FRAME OPENING HEIGHT
7-0
30"
9 3/4"
30"
CYLINDRICAL LOCK
MORTISE LOCK PREP
9 3/4"
5 1/2" DEADBOLT
ACTUAL HEIGHT
NOMINAL HEIGHT (FRAME OPENING)
1/8"
ACTUAL WIDTH
6-8
CLOSURE FRAME = 22-GA.
2-10
33 11/16"
3-0
35 11/16"
PUBLIC ACCESS - 1 1/8"
NO SILL OPTION - 3/4"
3-6
41 11/16"
JOB NUMBER
PROJECT
LOCATION
SHEET NUMBER
OF
Therma-Tru® Light Commercial/Multi-Family - Custom Elevations/Applications
JOB NUMBER
PROJECT
LOCATION
SHEET NUMBER
OF
Therma-Tru® Light Commercial/Multi-Family - Adjusta-Fit® Frames - Single
HARDWARE LOCATIONS
FRAME DETAIL
NOMINAL FRAME OPENING WIDTH
AVAILABLE THRESHOLDS
A
NOTE: BASE FRAME = 16-GA.
CLOSURE FRAME = 22-GA.
EXISTING WALL
ADJUSTA-FIT CLOSURE HEADER
ADJUSTA-FIT CLOSURE JAMB
ADJUSTA-FIT FRAME HEADER
STEEL ENTRANCE DOOR
7-0 = 85”
4" x 4" HINGE
6-8 = 81”
ADJUSTA-FIT FRAME
LATCH JAMB
2-0 = 24" 2-4 = 28" 2-6 = 30" 2-8 = 32"
2-10 = 34" 3-0 = 36" 3-6 = 42"
2-0 = 25"
2-4 = 29"
2-10 = 35"
2-6" = 31"
3-0 = 37"
NOTE: DEDUCT 5/8" FROM
ALL
NOMINAL
ROUGH
ROUGH
STANDARD HEIGHT DIMENSIONS
FRAME
OPENING
OPENING
FOR BARRIER FREE THRESHOLD
OPENING
WIDTH
HEIGHT - ST
2-0 x 6-8
25"
80 3/4"
STEEL ENTRANCE DOOR
2-4 x 6-8
29"
80 3/4"
2-6 x 6-8
31"
80 3/4"
2-8 x 6-8
33"
80 3/4"
2-10 x 6-8
35"
80 3/4"
1
1/8"
3-0 x 6-8
37"
80 3/4"
3-6 x 6-8
43"
80 3/4"
ADJUSTABLE SWEEP
2-0 x 7-0
25"
84 1/4"
ADJUSTABLE SWEEP
2-4 x 7-0
29"FREE THRESHOLD:
84 1/4"
BARRIER
2-6 x 7-0
31"
84 1/4"
OPTIONAL
TWO-PIECE THRESHOLD
2-8 x 7-0
33"
84 1/4"
2-10 x 7-0
35"
84 1/4"
3-0 x 7-0
37"
84 1/4"
3-6 x 7-0
43"
84 1/4"
1 3/4”
30”
ADJUSTA-FIT FRAME
HINGE JAMB
2-8 = 33"
3-6 = 43"
ADJUSTA-FIT FRAME
ADJUSTA-FIT KERFED FRAME
WALL SIZE
3 3/8" - 3 3/4"
3 3/4" - 4 1/8"
4 1/8" - 4 5/8"
4 5/8" - 5"
5 1/8" - 5 5/8"
5 5/8" - 6"
6 1/8" - 6 5/8"
6 5/8" - 7"
7 1/8" - 7 5/8"
7 5/8" - 8"
8 1/8" 8 5/8"
8 5/8" - 9"
9 1/8" - 9 5/8"
9 5/8" - 10"
10 1/8" - 10 5/8"
16-GA. BASE JAMB
22-GA. CLOSURE JAMB
CLOSURE MODEL
3
3A
4
4A
5
5A
6
6A
7
7A
8
ROUGH
OPENING
HEIGHT - STD
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
ROUGH OPENING
HEIGHT BARRIER FREE
80 1/8"
80 1/8"
80 1/8"
80 1/8"
80 1/8"
80 1/8"
80 1/8"
83 5/8"
83 5/8"
NOMINAL
FRAME83 5/8"
83 5/8"
OPENING
5/8"
2-0 83
x 6-8
5/8"
2-4 83
x 6-8
83 5/8"
2-6 x 6-8
2-8 x 6-8
2-10 x 6-8
3-0 x 6-8
3-6 x 6-8
2-0 x 7-0
2-4 x 7-0
2-6 x 7-0
2-8 x 7-0
2-10 x 7-0
3-0 x 7-0
3-6 x 7-0
ROUGH OPENING
HEIGHT NO SILL OPTION
79 3/4"
79 3/4"
79 3/4"
79 3/4"
79 3/4"
79 3/4"
79 3/4"
83 1/4"
83 1/4"
ROUGH
83 1/4"
OPENING
83 1/4"
WIDTH
83 1/4"
25"
83 1/4"
29"
83 1/4"
31"
33"
35"
37"
43"
25"
29"
31"
33"
35"
37"
43"
THRESHOLDS
TWO PIECE
BARRIER FREE
HINGES
REMOVABLE PIN
NON-REMOVABLE PIN
SPRING LOADED
BALL BEARING
LATCH PREPS
4 7/8" ANSI (STD)
T-STRIKE w/ DEADBOLT
ROUGH
OPENING
HEIGHT - STD
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
ROUGH OPENING
ROUGH OPENING
ADJUSTA-FIT
FRAMES
HEIGHT HEIGHT BARRIER FREE
NO SILL OPTION
80 1/8"
79 3/4"
KERFED
FOR
80 1/8"
79 3/4"
WEATHERSTRIPPING
80 1/8"
79 3/4" 1 13/16”
80 1/8"
79 3/4"
80 1/8"
79 3/4"
80 1/8"
79 3/4"
80 1/8"
79 3/4"
83 5/8"
83 1/4"
2 3/16” 83 1/4"
VARIES 83
WITH
5/8"
5/8"
83 1/4"
WALL 83
SIZE
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
5/8”
WALL SIZE
3 3/8" - 3 3/4"
3 3/4" - 4 1/8"
4 1/8" - 4 5/8"
4 5/8" - 5"
5 1/8" - 5 5/8"
5 5/8" - 6"
6 1/8" - 6 5/8"
6 5/8" - 7"
7 1/8" - 7 5/8"
7 5/8" - 8"
8 1/8" 8 5/8"
ROUGH
OPENING
WIDTH
25"
29"
31"
33"
35"
37"
43"
25"
29"
31"
33"
35"
37"
43"
2 1/8”
NOMINAL
FRAME
OPENING
2-0 x 6-8
2-4 x 6-8
2-6 x 6-8
2-8 x 6-8
2-10 x 6-8
3-0 x 6-8
3-6 x 6-8
2-0 x 7-0
2-4 x 7-0
2-6 x 7-0
2-8 x 7-0
2-10 x 7-0
3-0 x 7-0
3-6 x 7-0
ADJUSTA-FIT FRAME
SIDE JAMB
6-8 = 81 1/4”
30”
STEEL ENTRANCE DOOR
7-0 = 85 1/4”
COMPRESSION
WEATHERSTRIPPING
STRIKE LOCATION
NOMINAL FRAME OPENING HEIGHT
9 7/8”
MAGNETIC WEATHERSTRIPPING
EXISTING WALL
CLOSURE MODEL
3
3A
4
4A
5
5A
6
6A
7
7A
8
8A
9
9A
10
THRESHOLDS
TWO PIECE
BARRIER FREE
HINGES
REMOVABLE PIN
NON-REMOVABLE PIN
SPRING LOADED
BALL BEARING
LATCH PREPS
4 7/8" ANSI (STD)
T-STRIKE w/ DEADBOLT
Therma-Tru® Light Commercial/Multi-Family - Adjusta-Fit® Frames - Double
HARDWARE LOCATIONS
FRAME DETAIL
AVAILABLE THRESHOLDS
NOMINAL
FRAME WIDTH
OPENING
WIDTH
NOMINAL
FRAME
OPENING WIDTH
NOMINAL FRAME
OPENING
EXISTING WALL
NOTE: BASE FRAME = 16-GA.
CLOSURE FRAME = 22-GA.
ADJUSTA-FIT CLOSURE HEADER
Adjusta-Fit
MAGNETIC WEATHERSTRIPPING
ADJUSTA-FIT FRAME HEADER
4" X 4" INACTIVE HINGE
4-0 = 48 17/32"
5-0 = 60 17/32"
4-0 = 49 1/2"
5-0 = 61 1/2"
5-4 = 64 17/32"
5-4 = 65 1/2"
6-0 = 72 17/32"
6-0 = 73 1/2"
1 3/4”
30”
4" x 4" HINGE
ADJUSTA-FIT KERFED FRAME
WALL SIZE
3 3/8" - 3 3/4"
3 3/4" - 4 1/8"
4 1/8" - 4 5/8"
4 5/8" - 5"
5 1/8" - 5 5/8"
5 5/8" - 6"
6 1/8" - 6 5/8"
6 5/8" - 7"
7 1/8" - 7 5/8"
7 5/8" - 8"
8 1/8" 8 5/8"
8 5/8" - 9"
9 1/8" - 9 5/8"
9 5/8" - 10"
10 1/8" - 10 5/8"
16-GA. BASE JAMB
22-GA. CLOSURE JAMB
WALL SIZE
3 3/8" - 3 3/4"
3 3/4" - 4 1/8"
4 1/8" - 4 5/8"
4 5/8" - 5"
5 1/8" - 5 5/8"
5 5/8" - 6"
6 1/8" - 6 5/8"
6 5/8" - 7"
7 1/8" - 7 5/8"
7 5/8" - 8"
8 1/8" 8 5/8"
8 5/8" - 9"
9 1/8" - 9 5/8"
9 5/8" - 10"
10 1/8" - 10 5/8"
CLOSURE MODEL
3
3A
4
4A
5
5A
6
6A
7
7A
8
8A
9
9A
10
ROUGH
OPENING
HEIGHT - STD
80 3/4"
80 3/4"
80 3/4"
80 3/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
ROUGH OPENING
ROUGH OPENING
HEIGHT HEIGHT BARRIER FREE
NO SILL OPTION
80 1/8"
79 3/4"
80 1/8"
79 3/4"
80 1/8"
79 3/4"
80 1/8"
79 3/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
NOMINAL
ROUGH
83 5/8"
83 1/4"
FRAME
83 5/8"
83 1/4" OPENING
OPENING
2-0 x 6-8
2-4 x 6-8
2-6 x 6-8
2-8 x 6-8
2-10 x 6-8
3-0 x 6-8
3-6 x 6-8
2-0 x 7-0
2-4 x 7-0
2-6 x 7-0
2-8 x 7-0
2-10 x 7-0
3-0 x 7-0
3-6 x 7-0
WIDTH
25"
29"
31"
33"
35"
37"
43"
25"
29"
31"
33"
35"
37"
43"
THRESHOLDS
TWO PIECE
BARRIER FREE
HINGES
REMOVABLE PIN
NON-REMOVABLE PIN
SPRING LOADED
BALL BEARING
LATCH PREPS
ROUGH
4 7/8" ANSI (STD) ROUGH OPENING
OPENING
HEIGHT 4 7/8" ANSI w/ DEADBOLT
HEIGHT
- STD
BARRIER FREE
T-STRIKE
T-STRIKE
80
3/4" w/ DEADBOLT 80 1/8"
ROUGH OPENING
ADJUSTA-FIT FRAMES
HEIGHT -
KERFED80FOR
1/8"
WEATHERSTRIPPING
80 1/8"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
84 1/4"
VARIES WITH
84 1/4"
84 1/4" WALL SIZE
84 1/4"
84 1/4"
84 1/4"
84 1/4"
80 1/8"
80 1/8"
80 1/8"
80 1/8"
83 5/8"
3/16”
83 2
5/8"
83 5/8"
83 5/8"
83 5/8"
83 5/8"
83 5/8"
NO SILL OPTION
79 3/4"
79 3/4"
7913/16”
3/4"
1
79 3/4"
79 3/4"
79 3/4"
79 3/4"
83 1/4"
83 1/4"
83 1/4"
83 1/4"
83 1/4"
83 1/4"
83 1/4"
5/8”
4-0 x 6-8
5-0 x 6-8
5-4 x 6-8
6-0 x 6-8
4-0 x 7-0
5-0 x 7-0
5-4 x 7-0
6-0 x 7-0
ROUGH
OPENING
WIDTH
49 1/2"
61 1/2"
65 1/2"
73 1/2"
49 1/2"
61 1/2"
65 1/2"
73 1/2"
2 1/8”
NOMINAL
FRAME
OPENING
NOTE: DEDUCT 5/8" FROM ALL
STANDARD HEIGHT DIMENSIONS
NOMINAL
ROUGH
ROUGH
FOR BARRIER FREE THRESHOLD
FRAME
OPENING
OPENING
OPENING
WIDTH
STEEL ENTRANCE DOOR HEIGHT - ST
2-0 x 6-8
25"
80 3/4"
2-4 x 6-8
29"
80 3/4"
2-6 x 6-8
31"
80 3/4"
2-8 x 6-8
33"
80 3/4"
1
1/8"
2-10 x 6-8
35"
80 3/4"
3-0 x 6-8
37"
80 3/4"
ADJUSTABLE SWEEP
3-6 x 6-8
43"
80 3/4"
ADJUSTABLE SWEEP
2-0 x 7-0
25"FREE THRESHOLD:
84 1/4"
BARRIER
OPTIONAL
TWO-PIECE THRESHOLD
2-4 x 7-0
29"
84 1/4"
2-6 x 7-0
31"
84 1/4"
2-8 x 7-0
33"
84 1/4"
2-10 x 7-0
35"
84 1/4"
3-0 x 7-0
37"
84 1/4"
3-6 x 7-0
43"
84 1/4"
6-8 = 81”
ADJUSTA-FIT FRAME
INACTIVE HINGE JAMB
ADJUSTA-FIT FRAME
HINGE JAMB
7-0 = 85 1/4”
7-0 = 85”
INACTIVE
DOOR
ADJUSTA-FIT FRAME
SIDE JAMB
6-8 = 81 1/4”
9 7/8”
30”
STRIKE LOCATION
STEEL ENTRANCE DOOR
COMPRESSION
WEATHERSTRIPPING
TYPICAL BOTH SIDES
ACTIVE STEEL
ENTRANCE DOOR
EXISTING WALL
NOMINAL FRAME OPENING HEIGHT
ALUMINUM ASTRAGAL w/COMPRESSION
WEATHERSTRIPPING
ADJUSTA-FIT CLOSURE JAMB
TYPICAL BOTH SIDES
CLOSURE MODEL
3
3A
4
4A
5
5A
6
6A
7
7A
8
8A
9
9A
10
THRESHOLDS
TWO PIECE
BARRIER FREE
HINGES
REMOVABLE PIN
NON-REMOVABLE PIN
SPRING LOADED
BALL BEARING
LATCH PREPS
4 7/8" ANSI (STD)
T-STRIKE w/ DEADBOLT
FRAME DETAIL
Adjusta-Trim
AVAILABLE THRESHOLDS
EXISTING WALL
7 1/4”
ADJUSTA-TRIM CLOSURE
ADJUSTA-TRIM CLOSURE JAMB
EXISTING WALL
MAGNETIC WEATHERSTRIPPING
COMPRESSION
WEATHERSTRIPPING
ADJUSTA-TRIM FRAME
STEEL DOOR
“B”
COMPRESSION
WEATHERSTRIPPING
NOMINAL
FRAME
OPENING
2-0 x 6-8
2-4 x 6-8
2-6 x 6-8
2-8 x 6-8
2-10 x 6-8
3-0 x 6-8
3-6 x 6-8
2-0 x 7-0
2-4 x 7-0
2-6 x 7-0
2-8 x 7-0
2-10 x 7-0
3-0 x 7-0
3-6 x 7-0
ROUGH
OPENING
WIDTH
25"
29"
31"
33"
35"
37"
43"
25"
29"
31"
33"
35"
37"
43"
ROUGH
OPENING
HEIGHT - STD
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
WALL
SIZE
CLOSURE MODEL
THRESHOLDS
WEATHERSTRIPPING
3 3/8" - 3 3/4"
3
Two-Piece
X
3 3/4" - 4 1/8"
3A
Barrier Free
X
Compression
X
4 1/8"
- 4 5/8"
4
Frost Break
Inswing:
FBI
Frost Break
Outswing:
4 5/8"
- 5" FBO
4A
5 1/8" - 5 5/8"
5 5/8" - 6"
6 1/8" - 6 5/8"
6 5/8" - 7"
7 1/8" - 7 5/8"
7 5/8" - 8"
8 1/8" 8 5/8"
8 5/8" - 9"
9 1/8" - 9 5/8"
9 5/8" - 10"
5
5A
6
6A
7
7A
8
8A
9
9A
ROUGH OPENING
HEIGHT BARRIER FREE
80 1/8"
80 1/8"
80 1/8"
80 1/8"
80 1/8"
80 1/8"
80 1/8"
83 5/8"
83 5/8"
83 5/8"
83 5/8"
83 5/8"
83 5/8"
83 5/8"
ROUGH OPENING
HEIGHT NO SILL OPTION
79 3/4"
79 3/4"
79 3/4"
79 3/4"
79 3/4"
79 3/4"
79 3/4"
83 1/4"
83 1/4"
83 1/4"
83 1/4"
83 1/4"
83 1/4"
83 1/4"
STRIKE PREPS
Lip Strike w/ Opt. Deadbolt
T-Strike w/ Opt. Deadbolt
4 7/8" ANSI w/ Opt. Deadbolt
4 7/8" ANSI w/ Multi-Deadbolt
X
X
X
X
2-0 x 6-8
2-4 x 6-8
2-6 x 6-8
2-8 x 6-8
2-10 x 6-8
3-0 x 6-8
3-6 x 6-8
2-0 x 7-0
2-4 x 7-0
2-6 x 7-0
2-8 x 7-0
2-10 x 7-0
3-0 x 7-0
3-6 x 7-0
ROUGH
ROUGH
OPENING
OPENING
WIDTH
HEIGHT - STD
25"
80 3/4"
ADJUSTA-TRIM
FRAME
29"
80 3/4"
31"
80 3/4"
33"
80 3/4"
35"
80 3/4"
37"
80 3/4"
43"
80 3/4"
25"
84 1/4"
29"
84 1/4"
31"
84 1/4"
33"
84 1/4"
35"
84 1/4"
37"
84 1/4"
43"
84 1/4"
THRESHOLDS
TWO PIECE
FREE MODEL
WALL SIZE BARRIER
CLOSURE
HINGES
4 1/8" - 4 5/8"
4
4 5/8" - 5" REMOVABLE PIN
4A
PIN
5 1/8" - 5 5/8"NON-REMOVABLE
5
5 5/8" - 6" SPRING LOADED
5A
6 1/8" - 6 5/8"BALL BEARING
6
6 LATCH
5/8" - 7" PREPS
6A
7 1/8" - 7 5/8"4 7/8" ANSI (STD)
7
7 5/8" - 8" T-STRIKE w/ DEADBOLT
7A
8 1/8" 8 5/8"
8 5/8" - 9"
9 1/8" - 9 5/8"
9 5/8" - 10"
10 1/8" - 10 5/8"
HINGES
Removable Pin
Non-Removable Pin
Ball Bearing
Spring Loaded
STEEL ENTRANCE DOOR
7-0 = 85 1/4”
ROUGH OPENING
ROUGH OPENING
HEIGHT HEIGHT BARRIER FREE
NO SILL OPTION
80 1/8"
79 3/4"
80 1/8"
79 3/4"
ADJUSTABLE SWEEP
80 1/8"
79 3/4"
80 1/8" THRESHOLD
79 3/4"
TWO-PIECE
80 1/8"
79 3/4"
80 1/8"
79 3/4"
80 1/8"
79 3/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8" 16-GA. BASE JAMB 83 1/4"
83 5/8" 20-GA. CLOSURE JAMB 83 1/4"
A COMBINATION OF MAGNETIC AND
COMPRESSION WEATHERSTRIPPING
OFFERED ON KERFED FRAME.
8
8A
9
9A
10
FIRE RATINGS
"B" Rating 1 1/2 Hour
"C" Rating 3/4 Hour
No Rating
BARRIER FREE THRESHOLD:
OPTIONAL
ADJUSTA-TRIM KERFED FRAME
ADJUSTA-TRIM FRAMES
1/2”
1/2”
X
X
X
X
THRESHOL
Two-Piece
Barrier Free
Frost
Break Inswing: FBI
ADJUSTABLE
SWEEP
Frost Break Outswing: FB
1 1/8"
X
KERFED FOR
WEATHERSTRIPPING
VARIES WITH
WALL SIZE
2 3/16”
2”
VARIES
6-8 = 81”
4" x 4" HINGE
ADJUSTA-TRIM FRAME
LATCH JAMB
2-0 = 24" 2-4 = 28" 2-6 = 30" 2-8 = 32"
2-10 = 34" 3-0 = 36" 3-6 = 42"
NOMINAL
2-0 = 25" 2-4 = 29" 2-6" = 31" 2-8FRAME
= 33"
OPENING
2-10 = 35" 3-0 = 37" 3-6 = 43"
5/8”
ADJUSTA-TRIM FRAME
HINGE JAMB
NOTE: DEDUCT 5/8" FROM ALL
STANDARD HEIGHT DIMENSIONS
FOR BARRIER FREE THRESHOLD
1 3/4”
40 5/16”
“B”
WOOD SPACER
ADJUSTA-TRIM
FRAME SIDE JAMB
6-8 = 81 1/4”
“A”
7-0 = 85”
STEEL ENTRANCE DOOR
2”
ION
HARDWARE LOCATIONS
5/8”
NING
Therma-Tru® Light Commercial/Multi-Family - Adjusta-Trim® Frames - Single
10
HARDWARE LOCATIONS
FRAME DETAIL
AVAILABLE THRESHOLDS
NOMINAL
FRAME WIDTH
OPENING
WIDTH
NOMINAL
FRAME
OPENING WIDTH
NOMINAL FRAME
OPENING
NOTE: BASE FRAME = 16-GA.
CLOSURE FRAME = 22-GA.
EXISTING WALL
Adjusta-Trim
ADJUSTA-TRIM CLOSURE
EXISTING WALL
ADJUSTA-TRIM FRAME
STEEL DOOR
COMPRESSION
WEATHERSTRIPPING
TYPICAL BOTH SIDES
INACTIVE
DOOR
WOOD SPACER
ADJUSTA-TRIM
FRAME SIDE JAMB
NOTE: DEDUCT 5/8" FROM ALL
STANDARD HEIGHT DIMENSIONS
FOR BARRIER FREE THRESHOLD
4-0 = 49"
5-0 = 61"
5-4 = 64 17/32"
6-0 = 72 17/32"
NOMINAL
FRAME
5-4 = 65" 6-0 = 73"
OPENING
2-0 x 6-8
2-4 x 6-8
2-6 x 6-8
2-8 x 6-8
2-10 x 6-8
3-0 x 6-8
3-6 x 6-8
2-0 x 7-0
2-4 x 7-0
2-6 x 7-0
2-8 x 7-0
2-10 x 7-0
3-0 x 7-0
3-6 x 7-0
4" x 4" INACTIVE HINGE
ROUGH
OPENING
WIDTH
25"
29"
31"
33"
35"
37"
43"
25"
29"
31"
33"
35"
37"
43"
ROUGH
OPENING
HEIGHT - STD
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
80 3/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
6-8 = 81 1/4”
5-0 = 60 17/32"
STEEL ENTRANCE DOOR
ROUGH OPENING
ROUGH OPENING
HEIGHT HEIGHT BARRIER FREE
NO SILL OPTION
80 1/8"
79 3/4"
80 1/8"
79 3/4"
80 1/8"
79 3/4"
80 1/8" SWEEP
79 3/4"
ADJUSTABLE
80 1/8"
79 3/4"
TWO-PIECE THRESHOLD
80 1/8"
79 3/4"
80 1/8"
79 3/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
83 5/8"
83 1/4"
16-GA. BASE JAMB
83 5/8"
83 1/4"
1 3/4”
30”
4-0 = 48 17/32"
6-8 = 81”
ADJUSTA-TRIM FRAME
INACTIVE HINGE JAMB
ADJUSTA-TRIM
FRAME HINGE JAMB
4" x 4" HINGE
7-0 = 85 1/4”
7-0 = 85”
ACTIVE STEEL
ENTRANCE DOOR
30”
STRIKE LOCATION
NOMINAL FRAME OPENING HEIGHT
9 7/8”
MAGNETIC WEATHERSTRIPPING
ALUMINUM ASTRAGAL w/COMPRESSION
WEATHERSTRIPPING
ADJUSTA-TRIM CLOSURE JAMB
TYPICAL BOTH SIDES
1 1/8"
THRESHOL
Two-Piece
Barrier Free
Frost Break Inswing: FBI
Frost Break Outswing: FB
ADJUSTABLE SWEEP
BARRIER FREE THRESHOLD:
OPTIONAL
ADJUSTA-TRIM KERFED FRAME
20-GA. CLOSURE JAMB
CLOSURE MODEL
4
4A WEATHERSTRIPPING
5
X
5A Compression
X
X
6
6A
7
7A
8
8A
9
9A
10
ROUGH OPENING
HEIGHT BARRIER FREE
80 1/8"
80 1/8"
80 1/8"
80 1/8"
83 5/8"
83 5/8"
83 5/8"
83 5/8"
ROUGH OPENING
HEIGHT NO SILL OPTION
79 3/4"
79 3/4"
79 3/4"
79 3/4"
83 1/4"
83 1/4"
83 1/4"
83 1/4"
WALL SIZE
CLOSURE MODEL
4 1/8"
- 4 5/8"
4
THRESHOLDS
WEATHERSTRIPPING
4Two-Piece
5/8" - 5"
4A
X
5 1/8" -Free
5 5/8"
5
Barrier
X
Compression
5 5/8"Inswing:
- 6"
5A
Frost Break
FBI
6 1/8"
- 6 5/8" FBO
6
Frost Break
Outswing:
6 5/8" - 7"
6A
7 1/8" - 7 5/8"
7
7 5/8" - 8"
7A
8 1/8" 8 5/8"
8
8 5/8" - 9"
8A
9 1/8" - 9 5/8"
9
9 5/8" - 10"
9A
10 1/8" - 10 5/8"
10
X
STRIKE PREPS
Lip Strike w/ Opt. Deadbolt
T-Strike w/ Opt. Deadbolt
4 7/8" ANSI w/ Opt. Deadbolt
4 7/8" ANSI w/ Multi-Deadbolt
A COMBINATION OF MAGNETIC AND
COMPRESSION WEATHERSTRIPPING
OFFERED ON KERFED FRAME.
ADJUSTA-TRIM FRAMES
1/2”
1/2”
STRIKE PREPS
Lip Strike w/ Opt. Deadbolt
T-Strike w/ Opt. Deadbolt
4 7/8" ANSI w/ Opt. Deadbolt
4 7/8" ANSI w/ Multi-Deadbolt
X
X
X
X
HINGES
Removable Pin
Non-Removable Pin
Ball Bearing
Spring Loaded
X
X
X
X
FIRE RATINGS
"B" Rating 1 1/2 Hour
"C" Rating 3/4 Hour
No Rating
HINGES
Removable Pin
Non-Removable Pin
Ball Bearing
Spring Loaded
X
X
X
X
X
KERFED FOR
WEATHERSTRIPPING
VARIES WITH
WALL SIZE
2 3/16”
2”
WALL SIZE
4 1/8" - 4 5/8"
4 5/8" - 5"
THRESHOLDS
Two-Piece 5 1/8" - 5 5/8"
Barrier Free 5 5/8" - 6"
6 1/8" - 6FBI
5/8"
Frost Break Inswing:
6 5/8" - 7"
Frost Break Outswing:
FBO
7 1/8" - 7 5/8"
7 5/8" - 8"
8 1/8" 8 5/8"
8 5/8" - 9"
9 1/8" - 9 5/8"
9 5/8" - 10"
10 1/8" - 10 5/8"
ROUGH
OPENING
HEIGHT - STD
80 3/4"
80 3/4"
80 3/4"
80 3/4"
84 1/4"
84 1/4"
84 1/4"
84 1/4"
5/8”
4-0 x 6-8
5-0 x 6-8
5-4 x 6-8
6-0 x 6-8
4-0 x 7-0
5-0 x 7-0
5-4 x 7-0
6-0 x 7-0
ROUGH
OPENING
WIDTH
49 1/2"
61 1/2"
65 1/2"
73 1/2"
49 1/2"
61 1/2"
65 1/2"
73 1/2"
2”
NOMINAL
FRAME
OPENING
5/8”
G
Therma-Tru® Light Commercial/Multi-Family - Adjusta-Trim® Frames - Double
11
Therma-Tru® Light Commercial/Multi-Family - Secura-Fit® Frames - Single
HARDWARE LOCATIONS
FRAME DETAIL
AVAILABLE THRESHOLDS
>
> 682 10
” -7
-8 6” 2
EXISTING WALL
2-8 = 31 1/4”
2-10 = 33 1/4”
3-6 = 41 1/4”
6-8 = 79 5/8”
3-0 = 35 1/4”
7-0 = 83 5/8”
32 1/4”
32 1/4”
30 1/4”
2-6 = 29 1/4”
4 1/2” x 4 1/2”
HINGE
2-6 = 30” - 30 1/4” 2-8 = 32” - 32 1/4” 2-10 = 34” - 34 1/4”
3-6 = 42” - 42 1/4”
VARIES
1 3/4”
3-0 = 36” = 36 1/4”
VARIES
SECURA-FIT FRAME
LATCH JAMB
7-0 = 83 7/8” - 84”
7 1/4”
7 1/4”
30 1/4”
25 1/2”
25 1/2”
(3) BLANK
SECURA-FIT FRAME HEADER
STEEL DOOR
STEEL DOOR
SECURA-FIT FRAME
HINGE JAMB
OPTIONAL:
(2) DEADBOLT 1 1/8" x 2 3/4"
WEATHERSTRIPPING
MAGNETIC MAGNETIC
WEATHERSTRIPPING
COMPRESSION
WEATHERSTRIPPING
STANDARD
ANSI 115.3
2 3/4" STRIKE
(1) ANSI 115.1 - 4 7/8"
WOOD DOOR STOP,
INCLUDED w/ SECURA-FIT
WOOD DOOR STOP, INCLUDED
w/ SECURA-FIT FRAME
MAGNETIC
WEATHERSTRIPPING
MORTISED FOR
4 1/2” x 4 1/2” x
.134" HINGES (3)
VARIES
STRIKE LOCATION
NOMINAL FRAME OPENING HEIGHT
7 1/4”
EXISTING WALL
6-8 = 79 7/8” - 80 1/4”
NOMINAL FRAME OPENING WIDTH
NOTE:
SECURA-FIT FRAME = 16-GA.
>
> 678 6 ” 6-8 1
2” 0
72 6-0
” TO 6
78 6
”
> = GREATER THAN
ADJUSTABLE SWEEP
2-0 x 6-8
2-4 x 6-8
2-6 x 6-8
2-8 x 6-8
2-10 x 6-8
3-0 x 6-8
2-0 x 7-0
2-4 x 7-0
2-6 x 7-0
2-8 x 7-0
2-10 x 7-0
3-0 x 7-0
JOB NUMBER
PROJECT
LOCATION
SHEET NUMBER
OF
ROUGH
NOMINAL
OPENING
WIDTHFRAME
OPENING
24"
- 24 1/4"
28" - 28 1/4"
30" - 30 1/4"
32" - 32 1/4"
34" - 34 1/4"
36" - 36 1/4"
24" - 24 1/4"
28" - 28 1/4"
30" - 30 1/4"
32" - 32 1/4"
34" - 34 1/4"
36" - 36 1/4"
ROUGH
OPENING
HEIGHT
79 7/8" - 80 1/4"
2-0- 80
x 6-8
79 7/8"
1/4"
2-4- 80
x 6-8
79 7/8"
1/4"
2-6- 80
x 6-8
79 7/8"
1/4"
2-8- 80
x 6-8
79 7/8"
1/4"
2-10
x 6-8
79 7/8"
- 80
1/4"
3-0 x- 84"
6-8
83 7/8"
2-0 x- 84"
7-0
83 7/8"
2-4 x- 84"
7-0
83 7/8"
2-6 x- 84"
7-0
83 7/8"
2-8 x- 84"
7-0
83 7/8"
7-0
83 2-10
7/8" -x84"
3-0 x 7-0
JOB NUMBER
PROJECT
LOCATION
SHEET NUMBER
THRESHOLDS
ROUGH
ROUGH
TWO PIECE
OPENING
OPENING
BARRIER FREE
WIDTH
HINGES HEIGHT
24" - 24 1/4"
79 7/8" - 80 1/4"
REMOVABLE
PIN
28" - 28 1/4"
79 7/8" - 80 1/4" PIN
NON-REMOVABLE
30" - 30 1/4"
79 7/8" LOADED
- 80 1/4"
SPRING
32" - 32 1/4"
79 7/8"
- 80 1/4"
BALL
BEARING
34" - 34 LATCH
1/4"
79 7/8" - 80 1/4"
PREPS
36" - 36 1/4"
79 7/8" - (STD)
80 1/4"
T-STRIKE
24" - 24 1/4"
83 7/8"w/
- 84"
T-STRIKE
DEADBOLT
28" - 28 1/4"
83
7/8"
4 7/8" ANSI- 84"
30" - 30 1/4"
83 ANSI
7/8" -w/
84"DEADBOLT
4 7/8"
32" - 32 1/4"
83 7/8" - 84"
34" - 34 1/4"
83 7/8" - 84"
36" - 36 1/4"
83 7/8" - 84"
NOTE: DEDUCT 5/8" FROM ALL
STANDARD HEIGHT DIMENSIONS
FOR BARRIER FREE THRESHOLD
STEEL ENTRANCE DOOR
1 1/8"
ADJUSTABLE SWEEP
TWO-PIECE THRESHOLD
NOMINAL
FRAME
OPENING
SECURA-FIT FRAME
SIDE JAMB
BARRIER FREE THRESHOLD:
OPTIONAL
THRESHOLDS
TWO PIECE
BARRIER FREE
HINGES
REMOVABLE PIN
NON-REMOVABLE PIN
SPRING LOADED
BALL BEARING
LATCH PREPS
T-STRIKE (STD)
T-STRIKE w/ DEADBOLT
4 7/8" ANSI
4 7/8" ANSI w/ DEADBOLT
OF
JOB NUMBER
PROJECT
LOCATION
SHEET NUMBER
OF
12
Therma-Tru® Light Commercial/Multi-Family - Secura-Fit® Frames - Double
HARDWARE LOCATIONS
FRAME DETAIL
AVAILABLE THRESHOLDS
NOMINAL
FRAME WIDTH
OPENING
WIDTH
NOMINAL
FRAME
OPENING WIDTH
NOMINAL FRAME
OPENING
EXISTING WALL
NOTE: BASE FRAME = 16-GA.
WOOD DOOR STOP,
INCLUDED w/ SECURA-FIT
CLOSURE FRAME = 22-GA.
WEATHERSTRIPPING
MAGNETIC MAGNETIC
WEATHERSTRIPPING
SECURA-FIT FRAME HEADER
ALUMINUM ASTRAGAL w/
COMPRESSION WEATHERSTRIPPING
WOOD DOOR STOP w/ COMPRESSION
WEATHERSTRIPPING, INCLUDED w/
SECURA-FIT FRAME. TYPICAL BOTH
HINGE JAMBS
STEEL DOOR
30”
7-0 = 83 5/8”
ACTIVE STEEL
ENTRANCE DOOR
INACTIVE
DOOR
5-0 = 59 1/32"
4" x 4" HINGE
6-0 = 71 1/32"
5-4 = 63 3/4" - 64"
4" x 4" INACTIVE HINGE
6-0 = 71 3/4" - 72"
1 3/4”
30”
5-0 = 59 3/4" - 60"
5-4 = 63 1/32"
6-8 = 79 5/8”
SECURA-FIT FRAME
INACTIVE HINGE JAMB
SECURA-FIT FRAME
INACTIVE HINGE JAMB
7-0 = 83 7/8” - 84”
EXISTING WALL
6-8 = 79 7/8” - 80 1/4”
STRIKE LOCATION
NOMINAL FRAME OPENING HEIGHT
9 7/8”
Secura-Fit
ADJUSTABLE SWEEP
NOMINAL
FRAME
OPENING
4-0 x 6-8
5-0 x 6-8
5-4 x 6-8
6-0 x 6-8
4-0 x 7-0
5-0 x 7-0
5-0 x 7-0
6-0 x 7-0
JOB NUMBER
PROJECT
LOCATION
SHEET NUMBER
ROUGH
OPENING
4-0 x 6-8
WIDTH
x 6-8
47 3/4"5-0
- 48"
x 6-8
59 3/4"5-4
- 60"
x 6-8
63 3/4"6-0
- 64"
x 7-0
71 3/4"4-0
- 72"
x 7-0
47 3/4"5-0
- 48"
x 7-0
59 3/4"5-0
- 60"
x 7-0
63 3/4"6-0
- 64"
71 3/4" - 72"
JOB NUMBER
PROJECT
LOCATION
SHEET NUMBER
OF
ROUGH
OPENING
ROUGH
WIDTH
OPENING
HEIGHT47 3/4" - 48"
59 -3/4"
- 60"
79 7/8"
80 1/4"
63 -3/4"
- 64"
79 7/8"
80 1/4"
71 -3/4"
- 72"
79 7/8"
80 1/4"
47 -3/4"
- 48"
79 7/8"
80 1/4"
59 3/4"
- 60"
83 7/8"
- 84"
63 3/4"
- 64"
83 7/8"
- 84"
71 3/4"
- 72"
83 7/8"
- 84"
83 7/8" - 84"
NOTE: DEDUCT 5/8" FROM ALL
STANDARD HEIGHT DIMENSIONS
FOR BARRIER FREE THRESHOLD
STEEL ENTRANCE DOOR
1 1/8"
ADJUSTABLE SWEEP
TWO-PIECE THRESHOLD
NOMINAL
FRAME
OPENING
SECURA-FIT FRAME
SIDE JAMB
BARRIER FREE THRESHOLD:
OPTIONAL
ROUGH
THRESHOLDS
OPENING
TWO PIECE
THRESHOLDS
HEIGHT
BARRIER FREE
TWO PIECE
79 7/8" - 80 1/4" BARRIER FREE
HINGES
79 7/8"
- 80 1/4"
REMOVABLE PIN
HINGES
79 7/8" - 80 1/4" REMOVABLE PIN
NON-REMOVABLE PIN
79 7/8" - 80 1/4" NON-REMOVABLE PIN SPRING LOADED
83 7/8" - 84" SPRING LOADED
BALL BEARING
83 7/8" - 84" BALL BEARING
LATCH PREPS
83 7/8"
- 84"PREPS
T-STRIKE (STD)
LATCH
83 7/8" - 84" T-STRIKE (STD)
T-STRIKE w/ DEADBOLT
T-STRIKE w/ DEADBOLT 4 7/8" ANSI
4 7/8" ANSI w/ DEADBOLT
4 7/8" ANSI
4 7/8" ANSI w/ DEADBOLT
OF
JOB NUMBER
PROJECT
LOCATION
SHEET NUMBER
OF
13