Download Sears 279827 User's Manual

(5)- (110 SOURCE)
DRYER
MOTOR
KIT #279827.
INSTALLATION
AND WIRING
INSTRUCTIONS
for Pluggable Motor Replacement
_
ThlLsIat C_nt_lnt:
I Motto A_membly
2 !/_" Ferule Tmmlnals (kwulated)
1 Sheet. to.ruction
EI,e_trlcal 8h©.:k X_,_tsrd
Dis_mtecd
power INlf_
servl_g.
Failure tO do so could resuR In
s_loUa ht|ury ot death.
NOTE TO THE INS.T.A_ER:
This motor kit is an authorized FSP ser_ce _e_ment
p._t.for your epphc_tlon.The motorin this .kitmay or may notbe .klentl_lto your
ore.moOr, if your _re, m motor ha=the ptuggablemR _it_ (_e _ure.4B),
mpmceme eewlcemotor In me samemanneras you mmo_ __
motor.
If your doteOtlve motor has the switch where the wire lead from the _n
oonne_
Potm_tlat Fire Hazed andlor
Nulsam_e "l'dpplng of Motor Protector
00 NOT under any c4mumstance attempt
to remove oH"replace the motor switah
from this plugglb|e
_rvice
motor. The
swltoh is o non-serviceable
component,
Failure to do so oouid
injury or death,
result
In fire, serious
Remove defective motor using standarclmotor
removalprocedures.
2.
harness
rfollow Instru_ons below.
Compare and note the difference between the
detective motor and your new replscement motor The
first thing you will need to' compare is the motor
pulleys. The I_Uey supplied with the replaoement
motor can be used in zdl _ppgc_lons.
Al_ough
g_ere m_ two (2) €_ses, you may want Io use the
pulley from the def_t_ve motor. See Rgure I forthese
.
Remove Ixdley from replaaementmotor by using.two
(2) open end or adjual_de wrenches. Place one on
the motor shaft, rlghtbehb_:lglS ¢ulley, _ the other
on the pulley. Holdi_the motor shelf in ple.cewith
one (1) wrench, turn puikly with o_r wrench In a
COunte_e
dlmotlon to remove pulley. See
Figure E.
5. Remove beltrestrainerfromreple(;eme_t
motor.,._ee
F/gum2,
_i0VE PULLEY
2.SPEED
APPUCAT_ON
FAg[IRE!
NOTE: It you choose not to reuse your pulley
from the defective mlptor as shown In Figure I,
you will loose the 2..speed or 3-speed option.
fns(rucSonSheet 279807 7194
6,
From the s',_
end of b'le replacement motor, cut
the thread_l portion of the motor shMt off using a
hacksaw. See Rgure 3.
_LU_IABLE
CUI"II'IREAOED
7.
_th an allenwrench, remove re pulley t'rom the
dalec6ve motorand reinstallit on the mplacemem
motor.Be _uro to push pull_y ontothe motor st,._
allthe way andtightenthe setscrewsecurelyin place.
1
9.
PositionmotoraSshownb_
5. Note the locazior_
of the motor swl_.
Secure zpotor to bracket with
the odglnaJmotordamps.
Compare and note difference between the motor
s_etah of the defe_,e motor and the switch of '_e
new mp|a_ement motor, II the switches are the same,
simply inst_l] the motor in reve_
order you've
removed the defeotive motor. See F_v._e$ ,dA& 4B.
If not. proce_:l to step 9.
NOTE: Overload protector is part of the pluggable switch on the replacement motor and
separete on the old motog 9wit_.
OVERLOAO
PROTECTOR
OLO
MOTOR
SWITCH
omen .o
FIGURE44
279807
RGURE'J
(¢ontP,_O
WIRING
INSTRUCTIONS
10. Jnk.',_'A_ _r,d m ..m_ the blue |uml_r wito thlt runs
_rom the mot(_ sw_tohto the oved_ at_d discer¢.
SeeRgum6.
11.
"
_'_'_-----__e
s to
" " _
cu
w_e_omlnmpto, s_eF_ra 8-
to the
V4" retrainedrrm,
W,ed "l"_on the motor sw'd_.
See F_re 6.
13. Connect b'te red (:P.M),_re lead from ma]n hame,_s
_o the V,_"termlnal marked 'T on the motor swi_.
See F_ure 6.
14.'1"o oonnect b'm hie=k (61_ ,tAm le_ from n_n
h_m
a_d 1he v_lte _
v_
lead from n_n
,1,-_W_ te,
m_Io_a¢,_'_,_ _
_nin_s _
15. cut t_ _t4"_
to I_
_mlnal
fem_
_1_ tl_e_
_r_al
_
motor.
_he
_d
_ posmo_ewTtl_wire _!_.
16. SMp wires I:_ck approndmatelyII, of _u_inch.
Re.E6
17. With barrel Cdml_rs, crimp V_' _
fema_
temdn_s, ln_l_l
_
motto, onto _e Wireleads.
NOTE:
securely
Make sure
In piece.
terminels
ere
crimped
20. Reconnect ground _re, See Fngure_,
18. C,onneol the white (SM) wire lead from mille Ilarness
onto1tin _" terminal marked "6" on the matOr switch.
s_ebume_
19. _nrzect the black(6M) wire.leadfromm.l_nharnm_s
onlo the V_"terminalmarked"6"on the'motorswitch.
,SeeF/gum6.
21, All wire lead cormecllonsarecompleteat this point.
Finishreassemblingdryer.