Download Metra Electronics 99-7009 User's Manual

INSTALLATION INSTRUCTIONS FOR PART 99-7009
APPLICATIONS
Mitsubishi Endeavor
2004-2010
99-7009
KIT FEATURES
s DIN Head Unit Provisions
s ISO DIN Head Unit Provisions
KIT COMPONENTS
A) Radio Housing
s
B) ISO Brackets
s
C) Trim Plate
C
A
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
s-ITSUBISHIHARNESSUP
s-)4/-ITSUBISHIAMPLIFIED)NTERFACEUP
Antenna Adapter:
s.OTREQUIRED
TOOLS REQUIRED:
Phillips Screwdriver s Socket Wrench
1-800-221-0932
www.metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
99-7009
TA B L E O F C O N T E N T S
s Dash$ISASSEMBLY
-Mitsubishi%NDEAVOR----------------------------------
sKit!SSEMBLY
-ISOHeadUnitProvisionwithPocket----------------------------
-DINHeadUnitProvisionwithPocket----------------------------
sFinalAssembly------------------------------------------------------
sNotes----------------------------------------------------------------
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take
steps toward a better tomorrow.
99-7009
2004-2010 MITSUBISHI ENDEAVOR
Disconnect the negative battery terminal
to prevent an accidental short circuit.
2
Unsnap and remove entire panel surrounding radio and A/C controls.
A
(Figure A)
3 Remove (1) 10MM nut from the rear support
on the top left of radio on cross bar behind
dash. (FIGURE B)
B
4 Remove (3) Phillips screws to remove
factory radio chassis (Figure C)
5 Remove (4) Phillips screws from the pocket at the bottom of the radio and A/C panel
and remove the pocket. (This is where the
99-7009 will be mounted.) (Figure D)
C
D
1
D A S H D I S A S S E M B LY
1
..",%%.
@>I 6HH:B7AN
9>C=ZVYJc^iEgdk^h^dc
5SINGTHEFACTORYHARDWARE MOUNT
THEINTHELOCATIONWHERE
THEFACTORYPOCKETRESIDED
3LIDETHE$).CAGEINTOTHE2ADIO
(OUSINGANDSECUREBYBENDING
THEMETALLOCKINGTABSDOWN
3LIDETHEAFTERMARKETHEADUNIT
INTOTHECAGEANDSECURE 3NAP
TRIMPLATEINTOTHERADIOHOUSING
'
..",%%.
>HD9>C=:69JC>IEGDK>H>DC
-OUNTTHE)3/"RACKETSTOTHEHEAD
UNITWITHTHESCREWSSUPPLIEDWITH
THEUNIT
3LIDETHEHEADUNITINTOTHERADIO
OPENINGUNTILTHESIDECLIPSENGAGE
3NAPTHE4RIMPLATEINTOTHE2ADIO
(OUSING
@>I 6HH:B7AN
(
;>C6A 6HH:B7AN
..",%%.
!
"
#
!
3TRIPWIREENDSBACK
"
4WISTENDSTOGETHER
#
3OLDER
$
4APE
$
,OCATETHEFACTORYWIRINGHARNESSINTHEDASH
-ETRARECOMMENDSUSINGTHEPROPERMATING
ADAPTERANDMAKINGTHECONNECTIONSAS
SHOWN )SOLATEANDINDIVIDUALLYTAPEOFFTHE
ENDSOFANYUNUSEDWIRESTOPREVENTELECTRICAL
SHORTCIRCUIT3EEFIGURE!
2ECONNECTTHENEGATIVEBATTERYTERMINALANDTEST
THEUNITFORPROPEROPERATION
2EASSEMBLERADIOANDDASHASSEMBLIESIN
REVERSEORDEROFDISASSEMBLY
)
..",%%.
CDI:H
*
INST997009
1-800-221-0932
www.metraonline.com
Rev. 04-26-10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7009