Download Hotpoint WDM73 User's Manual

Getting to Know your Appliance
Recycling & Disposal
Information
www.theservicecentre.co.uk
NOTE: Hotpoint recommend, on completion of
your programme, that you switch off both the
electricity and water supply to the appliance.
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB.
PRINTED BY SIMLEX . FOUR ASHES, WOLVERHAMPTON.
Read the rest of these instructions to get the best from your appliance, remember to fill in your guarantee registration.
Keep this Book in a safe place for quick reference.
July 2003 - 1366200003-03
THIS WILL TAKE APPROXIMATELY 2hours 30minutes TO COMPLETE
Move your machine into position,
take care not to trap or kink the
hoses.
Turn one or both front feet
clockwise until the machine
stands firm and level.
The spring on each foot will
stop them coming loose.
✗
NOTE: Hotpoint recommend
extension leads are not used.
Brown (Live) wire to terminal
marked ‘L’ or coloured red.
6
CONNECT TO THE POWER SUPPLY...
(*see Getting to Know your Appliance)
WHICHEVER DRAINAGE METHOD
YOU USE, MAKE SURE THAT THE
HOOKED END SUPPORT IS FIXED
LEVEL TO, OR ABOVE THE ‘PLUMBING
INDICATOR LINE’*
7
Fix the hooked
end support at
a minimum
800mm from
the floor.
WARNING: The appliance must be earthed.
Electricity Supply
POLYSTYRENE BLOCK...
STEP 2
Insert drainage hose
approximately 100mm
into the standpipe.
WITHOUT ANY LAUNDRY
Remove and
retain 2 screws
from the back of
the worktop lid.
A cold fill adaptor is available from
your local Hotpoint authorised
Service Centre or by calling the
Genuine Parts & Accessories Hotline
(see KEY CONTACTS).
iii
Remove 3
screws and front
transit bracket
- retain.
Replace the worktop lid using
the 2 original screws.
ii
i
Hold free end of each hose over a bucket
and turn on water supply to check both hot
and cold water supplies are running freely.
Turn off the water supply taps and connect the
angled end of Red or Grey fill hose end to the
inlet valve marked ‘H’ and the angled end of the
Blue fill hose end to inlet value marked ‘C’ on rear
of machine.
Pour fabric conditioner into
the compartment.
We recommend that you do
not exceed the maximum
level indicated.
Old hoses may cause leaks
due to worn out washers.
Slide and push worktop lid back
into position, ensuring front edge is
correctly located into the console.
3
To achieve optimum wash
results we recommend that
you use the detergent
manufacturer’s dispensing
cup, to dispense no more
than 300ml of powder.
Dispensing Powder
Detergent
1
Pull the drawer out until
it reached its stop.
1. Drawer latch
2. Button
3. Main wash
Indicator
4. Main wash
compartment
5. Prewash
compartment
6. Fabric conditioner
compartment
Index:
Connect straight end of Red or Grey fill hose end
to the Hot water supply tap and straight end of
Blue fill hose end to the Cold water supply tap.
PLEASE USE THE NEW HOSES
SUPPLIED.
Installation
2
Press down on button,
to release the drawer
latch and remove the
drawer.
iv Turn on both water supply taps.
Remove 4 screws
and the rear
transit bracket
- retain.
REMOVE TWO TRANSIT FIXINGS...
Lift the main wash
indicator out of slots,
rotate and reposition for
Liquid, ensuring it is
secure.
Dispensing Liquid
Detergent
UNDER SINK METHOD
From the rear of
the machine,
grip sides of the
worktop lid, lift,
slide and pull
towards you.
It is advisable to clean the dispenser
drawer regularly:
Remove the drawer, see ‘Changing
the Main Wash Indicator’, wash
the dispenser drawer and clean
out the compartment.
Dry thoroughly and relocate.
Cleaning the Dispenser Drawer &
Compartments:
3
READY...
Hooked End Support
STANDPIPE METHOD
Relocate the drawer and
push back into place.
If you have no hot water supply...
DRAINAGE SYSTEM... we recommend one of the following:
2
and
Attach the GREY
drainage hose to the
under sink drainage
unit securely, using a
hose clip.
800mm
from floor
OR
.............................
1
cut off the blocked
end of the under sink
drainage unit.
Standpipe height:
minimum 500mm
from the floor.
WITHOUT ANY DETERGENT
✗
4
TO CHECK ALL PARTS OF THE INSTALLATION AND TO THOROUGHLY
CLEAN THE INSIDE OF YOUR MACHINE:
SELECT A 95˚ WHITE COTTON WASH PROGRAMME (refer to STEP 4).
PLUG YOUR MACHINE INTO AN ELECTRICAL SOCKET WHICH IS
EASILY ACCESSIBLE. SWITCH ON
Live
Fuses
Genuine Parts and Accessories
UK: 08709 077 077
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)
www.theservicecentre.co.uk
Republic of Ireland: (01) 842 6836
Troubleshooting
Please refer to the Troubleshooting
section if you have any problems when
using your washer dryer.
There may be nothing wrong!
READ BEFORE
CONTACTING
SERVICE!
NOTE: YOU MAY NEED A SECOND PERSON
TO HELP YOU RAISE AND LOWER THE
APPLIANCE.
We recommend a maintenance wash 2 or 3 times a year. to avoid a build
up of greasy deposits and water hardness residue.
Simply run wash programme ‘C’ without any laundry in the drum, using
the usual amount of detergent.
To minimise risk of injury to children, remove the door, plug and cut mains cable
off flush with the appliance. Dispose of these parts separately to ensure that the
appliance can no longer be plugged into a mains socket, and the door cannot be
locked shut.
STEP 8
Drying Guide
A picture guide provides a clear
explaination how to set a wash and auto
dry programme.
DO NOT overload the washer dryer.
Please dispose of packaging and old appliances carefully.
IMPORTANT:
Internal transit
brackets are fitted to
prevent damage
during transit and
MUST be removed
before use...
Failure to do so may
cause damage to
your machine!
Maintenance Wash:
As part of Hotpoint’s continued commitment to helping the environment,
Hotpoint reserves the right to use quality recycled components to keep down
customer costs and minimise material wastage.
STEP 7
Your appliance comes fitted with a plug and a 13 amp (13A) fuse. If
you need to replace the fuse, only those rated at 13A) and ASTA
approved to BS1362 should be used. To change fuse lift holder to
vertical position and lift fuse out. To replace, insert fuse and push fuse
holder down into locked position. Correct replacement is identified
by colour coding or the marking on base of plug.
WARNING: Do not use the plug unless the fuse holder is in locked position.
Extended Warranties
UK: 08709 088 088
(Open 8 to 8 Mon - Sun)
www.theservicecentre.co.uk
Republic of Ireland: 1850 502 200
DO NOT clean any part of the machine with abrasive cleaners, scouring
agents, acids, chlorine based bleach or metal polish as they may cause
damage.
Examples given for the maximum drying
load weight for different fabric types.
NOTE: In addition to the temperature of the
incoming water, the selection of optional wash
features will affect the programme times.
A wide range of genuine parts and accessories are available from our
hotline or through our web site.
Genuine parts and accessories, extended warranties and service
repairs are all available on our web-site at:
Wash & Dry Programme
Changing the Mains Lead
Note: Our operators will require the Model number and Serial number.
Genuine Parts and Accessories
UK: 08709 077 077
www.theservicecentre.co.uk
Republic of Ireland: (01) 842 6836
4
Clean the internal surface of the door bowl regularly with a soft cloth.
A build up of soap powder and water hardness residue may result in
water leaking from the door.
STEP 6
A guide to drying times is provided for
independent drying programmes, along
with a list of items not suitable for
tumble drying.
IF IT HAS NOT... REMOVE IT!
Cleaning the Door Bowl:
For pre purchase information on any other Hotpoint
product,
call: 08701 50 60 70 or visit: www.hotpoint.co.uk
Using your Machine / Options Guide
All available optional wash features are
explained within this section - These
allow you to adjust your selected wash
programme to suit your needs.
This is part of the packaging and
should have come away with the
polystyrene base -
Repair Service and Information Desk
UK: 08709 066 066
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)
www.theservicecentre.co.uk
Republic of Ireland: 1850 302 200
Use a damp cloth or silicon polish to clean the exterior surfaces of the
appliance.
STEP 5
A special lead can be ordered from Hotpoint Service
UK: 08709 066 066 or
Republic of Ireland on: 1850 302 200
If you have damaged the existing lead or require a longer one a
charge will be made. it is strongly advise that this work is carried out
by a qualified electrician.
Cleaning the Exterior:
After Sales Service
Over 1200 trained specialists, directly employed by us, ensure that
you can have complete confidence in both the appliances and
services we offer.
Changing the Plug
Retaining Flaps
Hooked End Support
NOTE: Always follow manufacturer’s dosage
recommendations.
Cut off and dispose of the supplied plug if it does not fit your socket.
Key Contacts
Examples are given for the maximum
washing load weights for different fabric
types.
Hotpoint recommend the Persil range of
detergent products.
NOTE: ALTHOUGH YOU MAY NEED TO
MOVE THE HOOKED END SUPPORT
ALONG THE GREY DRAINAGE HOSE,
DO NOT REMOVE IT.
Drainage Hose
Read through this section to familiarise
yourself with the different
compartments within the dispenser
drawer.
Wash Guide
A wash chart is provided to help you to
select your required programme.
WARNING: To avoid a shock hazard do not insert the discarded plug into
a socket anywhere else.
The Infobubble™ displays your selected wash programme, optional
wash features selected and shows you exactly where you are in the
washing cycle.
STEP 4
Dispenser Drawer
IMPORTANT: WIRES IN THE MAINS LEAD ARE COLOURED IN
Infobubble™ Display:
Hot Water inlet point and supplied
Hose (Red or Grey end)
Cold Water inlet point and supplied
Hose (Blue end)
Mains Cable
STEP 3
Guarantee terms and conditions
Your guarantee is only applicable in the United
Kingdom or Republic of Ireland and is subject to the
following provisions that your appliance:
● Has been installed and used correctly in accordance with
Extended Warranties
this instruction booklet.
UK: 08709 088 088
● Has been used solely for domestic purposes and is located
www.theservicecentre.co.uk
on domestic premises (ie. not for commercial or trade
Republic of Ireland: 1850 502 200
use).
Whether you have just one or a number of Hotpoint appliances in your
● Has been properly connected to a suitable electrical
kitchen, we offer two service cover plans to give you total peace of mind.
supply voltage as stated on the appliance rating plate.
● Repair Protection Plan - FREE service repairs for a single Hotpoint
● Has not been subject to misuse, accident, modified or
appliance during the period of cover.
repaired by anyone other than one of our own service
● Kitchen Cover
- FREE service repairs for all your Hotpoint
engineers.
appliances less than 8 years old.
ACCORDANCE WITH THE FOLLOWING CODE:
RED line indicates the minimum
height for the drainage hose.
Available 364 days a year with a fast, effective and value for money
service. We have the largest white goods repair service in the UK with over
1200 of our own fully trained engineers. All repairs include a parts and
labour guarantee for 12 months from the date of the repair.
If you require any information or have any questions about your
appliance, our operators are on hand with help and advice.
All this ensures that you will receive the best available after sales service
possible.
Earth
There will be a 2 minute spin about 20 minutes after the drying
programme has started; this improves the drying performance.
NOTE: This feature will not operate if you have selected a combined Wash
& Auto Dry Programme for synthetic fabrics.
-
Adjustable Feet
Remember you may be charged for a service call if a
problem with your washer dryer is caused by
incorrect installation or misuse.
WARNING: This appliance must be earthed.
Green/Yellow
Dry Spin:
Neutral
Reduces wear and tear on your laundry. A long, steady spin is
followed by a 30 second burst at the maximum speed for your
machine, to enable safer, more efficient water extraction.
Please read instructions thoroughly to
ensure you understand each stage
before you begin.
STEP 1
All Hotpoint appliances carry a fully inclusive 12 month parts
and labour guarantee as well as free replacement parts for the
first 5 years (except microwaves, selected integrated
appliances and cooker hoods, which have a one year
guarantee) provided that they are fitted by a Hotpoint
engineer.
Pulse Spin:
Dispose of packaging material in a safe
place and remove any labels.
Choose a location for your washer dryer,
where possible on a solid floor, with the
electrical sockets and water supply taps
easily accessible.
Allow sufficient space: 600mm width,
600m depth and 900mm height.
DO NOT install in a bath or shower
room.
Repair Service and Information Help Desk
UK: 08709 066066
www.theservicecentre.co.uk
Republic of Ireland: 1850 302 200
Note: Our operators will require the Model number and the Serial number
of your appliance.
Installation Guide
-
Less water, less creasing and less ironing. Gradually steps up the spin
speed for the most efficient water extraction.
Rating Plate
STEP 2
Electrical Guide
Blue
Profile Spin:
STEP 1
-
Reduces creasing on any wash programme by gradually reducing the
water temperature towards the end of the wash programme.
Brown
Auto Creasecare:
Makes the best use of the existing hot water supply, saving energy,
time and money.
Hotpoint recommends, for your own safety and to ensure you get the best possible results from your Washer
Dryer, you read through this booklet and follow these steps thoroughly.
LEVEL?...
Door Handle &
Release Button
“No company is better positioned to offer an after sales service on
a Hotpoint appliance than us - the manufacturer”.
As part of our commitment to you, all Hotpoint appliances have the
added benefit of a fully inclusive parts and labour guarantee for the first
12 months. In addition to this you also have the advantage of free
replacement parts for the first 5 years when fitted by a Hotpoint
engineer. When the 12 months parts and labour guarantee expires we
offer the following after sales service options:
5
Temperature Sensed Fill:
“Satisfaction guaranteed or your money back”
We give you a unique ‘satisfaction guaranteed’ promise - valid
for 90 days - after you have purchased your Hotpoint
appliance. If there is a technical problem simply call Hotpoint
Repair service or visit our web-site at
www.theservicecentre.co.uk and where necessary, we will
arrange for an engineer to call. If the technical problem is not
resolved under this guarantee, we will replace your machine
or, if you prefer, give you your money back.
INSTRUCTIONS FOR INSTALLATION & USE
WD72, WDM73
If you change the plug, the colour of wires in the mains lead may not
correspond with the colour of the markings identifying terminals in
the plug. You should therefore wire it as shown:
Optional Wash/Dry Feature
Buttons
After Sales Service
13A ASTA approved fuse to
BS1362.
Takes care of your laundry by monitoring your machine’s performance.
Prevents your machine spinning with an uneven load and reports any
specific problems on the Infobubble™ display.
Cancel button
Hotpoint guarantee
Green and yellow (Earth)
wire to terminal marked ‘E’,
symbol , or coloured
green and yellow.
Intelligent Care:
YOUR MACHINE WILL BE NOISY IF THE TWO FRONT FEET ARE NOT
ADJUSTED SO THE MACHINE STANDS FIRM AND LEVEL.
Automatic Features:
Mains On/Off button
Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.
Start, Buzzer/Time Delay
Button
Infobubble™ Display
CE marking certifies that this appliance conforms to the following
EEC directives:
Low Voltage Equipment - 72/23/EEC & 93/68/EEC
Electromagnetic Compatibility - 89/336/EEC, 92/31/EEC & 93/68/EEC
Wash Programme Buttons
Dispenser Drawer
CONNECT TO THE WATER
SUPPLY...
6
5
The main wash indicator
has been fitted to dispense
powder detergent only.
If you wish to use liquid
detergent, reposition the
main wash indicator as
shown below:
4
3
Changing the Main
Wash Indicator:
STEP 3
The Dispenser Drawer
2
1
Choosing a Washing Programme
50
40
Coloured nylon, polyester,
acrylic/cotton mixtures, cotton
or viscose with special finishes
(eg. drip dry), coloured
polyester/cotton mixtures
Acrylics, acetates & tri-acetate
blends of these fabrics with
wool, polyester/wool blends
C
D
E
warm
30
0.9kg
1.4kg
1.4kg
40
Selecting a Prewash
For gentle wash, rinse & spin options see STEP7.
Refresh programmes
Silk & printed acetate fabrics
with colours not fast at 40˚
2.7kg
40
3kg
F,G & H
Synthetic
2kg max.
2.5kg max.
●
●
●
80
40-50
50-60
30-40
90
60
80
50
IRON DRY FULL DRY
Switch ‘ON’
The Infobubble™ will
display ‘Select
Programme’.
Did the water pump out?
If not see ‘MY MACHINE DOES
NOT PUMP OUT WATER’.
There has been an unbalanced load
and the machine could not spin.
Redistribute the clothes by hand
and select a spin only programme.
✓
Was a short spin programme
used on a non-synthetic load.
MY LAUNDRY HAS NOT
SPUN DRY.
See STEP 2: Installation
✓
Have you adjusted the feet to
stabilise the machine?
The ‘Rinse Hold’ button has
been pressed and this will be
displayed in the Infobubble™
display until the button is
pressed again.
MY MACHINE STOPS
BEFORE A SPIN
PROGRAMME.
If not replace it, see STEP 1:
Electricity Supply
If possible use another socket
for the machine.
Plug the machine in and
turn the socket switch on.
Is the fuse in the plug OK?
Is the socket OK? Test with
another appliance to check.
✓
Did the ‘door indicator’ light
come on after 2 seconds?
✓
Check that a time delay has
not been set on the machine.
Close the door. Choose a
programme and then press start.
MY MACHINE WILL NOT
START
Is the machine plugged in
and switched on?
✓
✗
● Misuse of the
dryer may create
a fire hazard.
Minimises creasing of silk by
suspending wash load in final
rinse water.
Cancel
Fabric
Care
-
Protects delicates with a
gentle wash, automatic rinse
hold and 800rpm spin.
Cancel
Selects
Time
Saver
-
-
Bioprofile -
Action
Bioprofile &
Time Saver together.
Saves up to 25 minutes on
lightly soiled items by
reducing the wash & spin
time of any programme.
Increases water temperature
at stages to ensure maximum
wash performance from your
biological detergent.
Rinse Hold, Fabric Care,
Variable Rinse, Variable
Spin & Time Saver.
Wool Rinses
& Spin 1000
Rinse &
Super Spin
1200
x3
Rinse for hand washed Variable Rinse.
woollens or as an extra
rinse for programme ‘F’.
Rinse for hand washed Variable Rinse.
cottons or as an extra
rinse for programme ‘F’.
Refresh 40˚C A very quick light wash No options.
for freshening up.
x2
Gentle Wash for Silks.
Once
x4
x3
x2
x1
Press
Button
✗
✗
✗
✗
Clean fabric dispenser drawer.
See STEP 3:‘The Dispenser
Drawer’.
WATER COLLECTS IN THE
FABRIC DISPENSER
COMPARTMENT
Check the blocked end of the
under sink drainage unit has
been cut off.
✓
Is the machine connected to
a sink waste system?
Clear any blockages that have
been found
See STEP 2: Installation
✓
Has ‘Rinse Hold’ been selected?
✗
The light will flash until the button
is pressed again.
✓
Press the ‘Rinse Hold’ button
again.
Are the drainage unit, standpipe
or under sink connections free
from blockages?
✓
Has the drain hose been installed ✗
correctly?
MY MACHINE DOES NOT
PUMP OUT WATER
(E15)
Switch ‘ON’.
The Infobubble™ will
display ‘Select
Programme’.
● Do not use a dosing ball
to dispense detergent
when using a wash and
auto dry programme.
1-2 minutes after
completion of the wash
programme the
symbol will disappear
and the door can be
opened. Switch ‘OFF’
after use.
9
Add detergent /
conditioner to the
dispenser drawer
(STEP 3). Refer to the
manufacturer’s
dosage instructions.
4
5
Return to normal programme setting.
Delete a rinse to save time and water.
Add a rinse for sensitive skin.
Action
● Not available with Programme ‘F’.
Variable Rinse
Return to normal programme setting.
Reduce spin speed by 100rpm intervals to
400rpm or ‘0’ (no spin).
x2
& Hold
x3
Display existing programme spin speed.
Press ‘START’, the door
will lock and the
symbol will appear in
the Infobubble™
throughout the wash
& dry programme.
8
Gives you the option to delay
your wash programme from
1 to 18 hours.
Lets you know when the
programme has finished or
when Rinse Hold is activated.
x1
Action
Variable Spin
Press
Button
● Do not attempt to open the
door when water is visible in
the drum or if the
symbol
is displayed in the
Infobubble™.
Options
Available
Silk 30˚C
-
-
Check the feet have been
levelled.
The machine is designed to
release steam from the dispenser
drawer during hot washes.
✓
Is steam coming from the
dispenser drawer?
You may need to call in a
plumber.
✓
Is the standpipe or household
drain blocked.
Turn the main supply tap
down.
Is your water pressure too
high?
✓
Are the fill hoses on correctly?
If not tighten them.
MY MACHINE IS LEAKING
(E10/11/13)
✗
✗
✗
Is the cold water turned on at the ✗
tap?
THE LAUNDRY IS NOT DRY
AFTER USING THE DRY
PROGRAMME
Check the correct amount of
suitable detergent has been used,
refer to manufacturer’s
recommendations.
SUDS ARE COMING FROM
THE DISPENSER DRAWER
Check for low temperature and
low pressure of the hot and cold
water supply.
Was the laundry spun dry at the
end of a wash programme, if not
select a spin and dry option to
suit the fabric type.
✓
Did you select the right heat/time
setting?
✗
Call for a Service Engineer.
Motor Drive Problem Run the programme again,
if problem persists call for
a Service Engineer.
Call for a Service Engineer.
You will be asked for the following
details: Name and Address, Post
Code,Telephone Number, Date of
Purchase, Colour and Model/Serial
Numbers - which can be found on
the inside of the door.
Clear and precise details of the query
or fault.
If your machine is still not working
contact:
Repair Service and Information Desk
UK 08709 066 066
Republic of Ireland 1850302 200
E50/51
E30/31
E14
High water level Disconnect or turn off the
water supply, then call for a
Service Engineer.
Door is not closed properly
Pressure at the 2 o’clock
position until door clicks.
E17
E16
Water will not pump out See ‘MY MACHINE DOES
NOT PUMP OUT WATER’.
E15
E10/11/13 No Hot / Cold fill Check the water supply
and the hot and cold hose
connections.
In the unlikely event of a problem
occuring with your machine, an Error
Code will appear in the Infobubble™.
Brief explanations of the codes are
shown below:
ERROR CODES
NOTE: Returns Infobubble™ display to Silks 30˚C
x9
Spin for hand washed
delicates or as an extra
spin for programmes
‘D,E & G’.
Spin for hand washed No options
woollens or as an extra
spin for programme ‘F’.
Slow Spin
800
Wool Spin
1000
No options.
x8
x7
Spin for hand washed
cottons or as an extra
spin for programmes
‘A,B & C’.
Super Spin
1200
x6
Infobubble™
Display
Infobubble™
Display
Rinses & Slow Rinse for hand washed Variable Rinse
Spin 800
delicates / acrylics or as
an extra rinse after
programmes ‘D,E & G’.
THE PROGRAMME TAKES A
LONG TIME
✓
Infobubble™
Display
x5
Gentle Wash. Rinse & Spin Options for Programme G
● Do not overload the
appliance! It may
damage laundry and
reduce the quality of
the wash.
Select optional wash &
dry features (STEP 5),
you will hear a beep
and the Infobubble™
will display the
selection.
7
Press Infobubble™ Description
Button Display
● Do not allow children
to play with the
appliance or tamper
with the controls.
3
Infobubble™
Display
Note: When the button is released the programme will start automatically
and the Infobubble™ will display ‘Starting’.
Time
Delay
Buzzer
Wash & Auto Dry Programme
Infobubble™
Display
Infobubble™
Display
x1
& Hold
Action
Start, Buzzer / Time Delay
Press
Button
Sort laundry by label Close door by
into groups with the applying pressure at
same wash & dry
the 2 o’clock position.
requirements, load
the appliance.
See Drying Weight
Load examples (STEP 6)
2
Select optional wash
programme (STEP 4),
you will hear a beep
and the Infobubble™
will display the programme information.
6
Switch on both the
water and electricity
supply at the mains.
1
STEP 7
Cancel
Reduce programmed temperature in 5˚C
intervals to a minmum of 30˚C
Action
WARNINGS:
x2
x1
& Hold
Press
Button
Variable Temperature
x4
x3
x2
x1
Press
Button
Bioprofile / Time Saver
x3
x2
Selects full heat programme
Selects low heat programme
Action
Note: To increase drying time by 10 minute increments, up to 120 minutes,
press and hold button.
x2
x1
Press
Button
More ‘Troubleshooting information and general product advice can be found on our website, visit: www.theservicecentre.co.uk/help
● On no account
should liquid fabric
conditioner be
added during the
drying process.
1-2 minutes after
completion of the
wash programme the
symbol will
disappear and the
door can be opened.
Switch ‘OFF’ after use.
6
= 2kg
Children’s Dresses
Shirts
Blouses
Set of Pyjamas
-
Infobubble™
Display
Drying Programme / Drying Time
● Not available with Programme ‘F’.
Remember, you will be charged for a service call for problems caused by incorrect installation, non-removal of transit bolts or packaging, leaks from household pipework, loose or blocked fill and drain hoses.
Washing items that DO NOT have a wash label or washing items that are not intended as machine washable and NOT emptying contents from pockets may cause pump or drain blockages, or may damage components within the machine.
Remember, you will be charged
for a service call to rectify a
malfunction resulting from
objects, such as coins, pens, hair
grips etc. falling from pockets.
Limit the size of absorbent loads
ie. towels, to 3kg (7lb) to give
good washing and rinsing results.
Place small items in a wash bag.
Always follow the care label on
items when choosing the wash
programme.
Wash non-colourfast items or
really dirty laundry separately as
they may affect other items.
2
2
4
1
Press ‘START’, the door
will lock and the
symbol will appear in
the Infobubble™
throughout the wash
& dry programme.
5
= 2.5kg
Bath Towels
Shirts
Blouses
Set of Pyjamas
Sets of Underwear
Pillow Case
SYNTHETIC
1
3
3
1
2
1
COTTON
Two examples of typical
loads for drying
different types of fabric:
Has the polystyrene block been
removed from underneath the
machine?
✓
Have both transit bolts been
removed from the machine?
Check all loose items, such as
coins, have been removed
from the laundry.
MY MACHINE MAKES A
NOISE OR VIBRATES IN A
SPIN PROGRAMME.
Troubleshooting -
● Be careful not to
touch the drum
at the top as this
area gets hot during
drying.
Select optional wash &
dry features (STEP 5),
you will hear a beep
and the Infobubble™
will display the
selection.
4
Independent Drying Programme
NOTE: After you have dried a particularly ‘fluffy’ load, or if you have used the
appliance as a dryer only, remove the load then run a ‘rinse and spin’ cycle to
flush fluff out of the pipes. This appliance does not have a filter for you to
clean.
This machine incorporates a ‘Dry Spin’ feature, see Automatic Features.
● Do not overload the machine
(maximum load 6kg).
In addition to reducing the
quality of the wash, this may also
damage your laundry and the
machine.
● We strongly recommend that you
do not wash underwired bras in
this machine. Should the wires
become detached it could cause
damage to your clothes and the
machine. If the washcare label
states that the bra is machine
washable, then we advise placing
it in a sealed pillow case or a
similar washbag. Remember, you
will be charged for a service call
resulting from a detached bra
wire.
● Do not use the machine if the
item to be washed does not have
a wash label.
Before washing laundry we
recommend that you do the
following:
● Pre-treat awkward stains with
washable treatments.
Do not wash any items that have
previously been treated with
solvents.
● Close zips, fasten belts, tie strings
and close press studs to prevent
tangling.
● Empty ALL objects from pockets
as they may damage the clothes
and the machine.
●
Low
Low
High
High
HEAT
All fabrics contain a little natural moisture even when ‘dry’, this should not
be lost if the clothes are to remain soft and fluffy. If clothes are subjected
to extreme drying the tend to wrinkle and consequently need more
ironing than usual. As clothes feel damper when warm, allow for this
when removing items before the ‘Cool Tumble’ phase is complete.
Washcare Tips:
STEP 8
Short
Short
Long
Long
SPIN
Time Setting
(approx. mins)
symbol is
DRYING WEIGHT
LOADS
WARNING: Do not attempt to open the door whilst the
displayed in the Infobubble™
Indicator Light...
When ‘START’ is pressed the door will lock and a
symbol will be
displayed in the Infobubble™ throughout the programme.
Approximately 1-2 minutes after the programme has finished the
symbol will disappear and the door can be opened.
each drying cycle allows fabrics to gently cool down, minimising creasing.
3
= 3kg
Children’s Dresses
Shirts
Blouses
Set of Pyjamas
Sets of Underwear
To Close...
Apply pressure at the 2 o’clock position until the door clicks.
IMPORTANT INFORMATION: A 10 minute ‘Cool Tumble’ phase at the end of
B,C,D & E
Natural
2
4
4
1
4
SYNTHETIC
= 5kg
Rinse
Hold
Action
Note: To spin, press the ‘Rinse Hold’ button again (the Infobubble™ display
will remind you to do this, or select the buzzer).
x1
Press
Button
● Not available with Programme ‘F’.
Bath Towels
Shirts
Blouses
Sets of Pyjamas
Sets of Underwear
Pillow Cases
Rinse Hold / Fabric Care
NOTE: If pressed when setting ‘Time Delay’ or when time delay is
active, time delay is cancelled but the selected wash programme and
optional wash features will remain, the Infobubble™ will display
these. Press start to proceed with the programme.
COTTON
2
6
6
2
4
2
Optional Wash Features
To start the selection again, press and hold the cancel button for a few seconds, all settings displayed will disappear and the
Infobubble™ will display ‘Select Programme’.
Cancel Button
STEP 5
Two examples of
typical loads for
washing different
types of fabric:
WEIGHT OF
WASH LOAD
To Open...
Grip the door handle and press the button whilst pulling open the door.
Fabric Programme Dry Weight
Programme
Type
Load
Selector Setting
Close the door by
applying pressure at
the 2 o’clock position.
2
900rpm
900rpm
900rpm
900rpm
900rpm
900rpm
1200rpm
1200rpm
1200rpm
Approx. Max
Spin Speed
depending
on model
Interlocking Door System:
30 - 35
35 - 40
40 - 50
55 - 65
50 - 60
60 - 70
70 - 80
150 - 170
120 - 140
Programme
Time (mins)
based on hot
and cold fill
Choosing a Drying Programme
● If your appliance is not permanently
● The dryer is intended
plumbed in, turn on the cold water supply
for use only where
to the appliance and hook the drain hose
water is used for the
over the sink to enable the condensing
cleaning process.
action to work.
WARNINGS:
Remove the wet
laundry and dosing
ball (if used) until the
correct ‘Drying
Weight Load’ is left in
the drum.
1
● Garments with the ITCL
code DO NOT TUMBLE DRY.
● Woollens.
● Large bulky items eg.
quilts, bedspreads,
pillows etc... expand
when dry, preventing air
flow through the
appliance.
● Items containing plastic
film, foam rubber or
rubber like materials eg.
pillows, cushions, PVC
rainwear or inflammable
articles which contain
inflammable substances
eg. towels contaminated
with hair lacquer
● Fibreglass (eg. some
types of curtains).
● Items which have been
dry cleaned.
Items Not Suitable
for Tumble Drying:
STEP 6
To select, press button.
Press again to cancel.
Button Selection:
To cancel, press the wash programme button a third time and a beep will
be heard.
For heavily soiled loads, press and hold the required wash programme
button until a second beep is heard, the infobubble™ will display
‘Prewash’ and .
G
F
5kg
40
Non-colourfast cotton, linen
& viscose
B
Woollen blankets, wool
mixtures with cotton, rayon
or silk.
Shrink resistant machine
washable wool
5kg
Colourfast cotton, linen or
viscose without special finishes 60
3kg
5kg
95
White cotton & linen
without special finishes.
A
Full
Load
Temp.
˚C
Codes
Fabric
ITCL
programme times.
IMPORTANT INFORMATION: The temperature of the incoming water supply and selection of any Optional Wash Feature will affect the
STEP 4