Download Honda 08B21-SJC-102 User's Manual

www.collegehillshonda.com
Accessory
INSTALLATION
INSTRUCTIONS
PARTS LIST
Application
Publications No.
AII 36587
REAR CAMERA
ATTACHMENT
(EX-L WITH NAVI)
2006-2008 RIDGELINE
Issue Date
MAY 2007
Template
Attachment Kit
P/N: 08B21-SJC-102
Rear camera trim
19 Wire ties
Rear camera bracket
10 Small wire ties
6 Wire ties with clip
Rear camera subbracket
6-Pin connector
Harness clamp bracket A
Grommet
Harness clamp bracket B
2 Clear adhesive tapes
Rear camera subharness
3 Blind nuts
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
AII 36587 (0705)
08B21-SJC-1010-91
1 of 17
www.collegehillshonda.com
2 EPT sealers
4 Cushion tapes
2 Socket bolts, 4 x 10 mm
3 Washer screws, 4 x 12 mm
2 Washer screws, 4 x 6 mm
7 Clips
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
10 mm Combination wrench
Ratchet
10, 12 mm and 14 mm Socket
Torque wrench
File
Isopropyl alcohol
Shop towel
Tape measure
Drill
3 mm, 8 mm, and 10 mm Drill bits
Utility knife
T40, and T50 Torx bit
KTC trim tool
Scissors
Tape
Electrical tape
Wire
3 mm Hex wrench
Illustration of the Rear Camera Installed on the
Vehicle
NAVI CONTROL UNIT
GROMMET
Round grommet
REAR
CAMERA
6 Oval grommets
REAR CAMERA
SUBHARNESS
Accessory user’s information manual
6-PIN CONNECTOR
4712100K
INSTALLATION
Rear Camera Kit (sold separately)
P/N: 08A57-SJC-100
Rear camera
2 of 17
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio, then write down radio station presets.
2.
Disconnect the negative cable from the battery.
AII 36587 (0705)
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
www.collegehillshonda.com
3.
5.
Remove the fuel fill door release handle. Remove
the left front door sill trim (three clips and three
retaining tabs).
RETAINING
TABS
Pull away the weatherstrip from the B-pillar lower
trim panel. Remove the left seat belt lower anchor
bolt cover and remove the lower anchor bolt.
Remove the left B-pillar lower trim panel by
pulling out toward you as shown.
•
FUEL FILL DOOR
RELEASE HANDLE
LEFT FRONT
3 CLIPS
DOOR SILL TRIM
Seat belt anchor bolt torque:
30 to 35 N·m (22 to 25 lbs)
WEATHERSTRIP
(Pull away.)
RETAINING
TAB
FRONT
LEFT
B-PILLAR
LOWER
TRIM
PANEL
FRONT
3916041T
4.
LOWER ANCHOR
BOLT COVER
Remove the left rear door sill trim (three clips and
four retaining tabs).
LEFT REAR
DOOR SILL TRIM
RETAINIG
TABS
LEFT SEAT BELT
LOWER ANCHOR BOLT
6.
4212330T
Remove the driver’s seat frame rear cover (two
clips and two hooks).
3 CLIPS
RETAINIG
TABS
DRIVER’S SEAT
FRONT
4212450T
2 HOOKS
DRIVER’S SEAT
FRAME REAR COVER
4713010K
2 CLIPS
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
AII 36587 (0705)
3 of 17
www.collegehillshonda.com
7.
9.
Lift up the rear seats, and remove the rear seat
under covers;
•
Remove the right rear seat under cover (four
clips).
•
Remove the left rear seat under cover (five
clips).
Remove the rear seat belt anchor bolt and eight
seat anchor bolts.
•
Seat belt anchor bolt torque:
30 to 35 N·m (22 to 25 lbs)
LEFT REAR
SEAT CUSHION
RIGHT REAR
SEAT CUSHION
RIGHT REAR
SEAT UNDER
COVER
9 CLIPS
8.
8 SEAT
ANCHOR
BOLTS
LEFT REAR
SEAT UNDER
COVER
•
4212362T
4212342T
10. Remove the cap from the rear trim panel cover
(four retaining tabs for each cover), and remove
the rear seat.
Remove the rear seat bracket covers;
•
REAR SEAT
BELT ANCHOR
BOLT
Remove the left and right rear seat bracket
covers (two clips for each cover).
4 RETAINING
TABS
Remove the center seat bracket cover (two
clips and nine retaining tabs).
CAP
4 RETAINING
TABS
CAP
LEFT REAR
SEAT BRACKET
COVER
CLIPS
REAR SEAT
9 RETAINING
TABS
CENTER SEAT
BRACKET
COVER
2 CLIPS
4 of 17
RIGHT REAR
SEAT BRACKET
COVER
4212371T
4212460T
CLIPS
AII 36587 (0705)
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
www.collegehillshonda.com
11. Remove the rear trim panel cover (eight clips and
two retaining tabs).
14. Remove the left rear lower anchor bolt cover, and
remove the left rear seat belt lower anchor bolt.
•
2 RETAINING
TABS
Seat belt anchor bolt torque:
30 to 35 N·m (22 to 25 lbs)
REAR TRIM
PANEL COVER
CLIP
6 CLIPS
2 CLIPS
LEFT REAR
LOWER
ANCHOR
BOLT COVER
CLIPS
LEFT REAR
SEAT BELT
LOWER
ANCHOR
BOLT
4212381T
12. Remove the left rear seat belt upper anchor bolt
cover (four retaining tabs), and remove the left
rear seat belt upper anchor bolt.
•
4715611K
LEFT REAR
PILLAR
LOWER TRIM
15. Remove upper clip, then pull the left rear pillar
lower trim out toward you to release two clips.
Seat belt anchor bolt torque:
30 to 35 N·m (22 to 25 lbs)
16. Remove the left rear taillight (two bolts, two clips
and vehicle connector). Remove the right taillight
the same way.
CLIP
LEFT REAR SEAT
BELT UPPER
ANCHOR BOLT
LEFT SIDE
RIGHT SIDE
4 RETAINING
TABS
VEHICLE
CONNECTOR
LEFT REAR
SEAT BELT
ANCHOR BOLT
COVER
VEHICLE
CONNECTOR
2 TABS
LEFT REAR PILLAR
UPPER TRIM
BOLTS
CLIP
4715601K
2 CLIPS
13. Remove the left rear pillar upper trim.
•
With side airbag; pull the clip, and remove the
left rear pillar trim by releasing the one clip.
•
Without side airbag; remove the left rear pillar
trim by releasing the two clips.
LEFT
TAILLIGHT
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
AII 36587 (0705)
VEHICLE
CONNECTOR
3924012H
5 of 17
www.collegehillshonda.com
17. Remove the rear bumper:
•
Remove the license plate (two bolts).
•
Remove two bolts, six self-tapping screws and
six clips from the rear bumper.
•
Pull the rear bumper toward you. Unplug the
two vehicle connectors, and remove the rear
bumper.
•
Set the rear bumper on the blanket.
•
Using a KTC trim tool, carefully pry up the
front of the trim to release the three front clips.
Start with the left clip and work towards the
right clip.
•
Gently left the front of the trim to release the
four rear clips.
7 CLIPS
KTC TRIM TOOL
2 VEHICLE
CONNECTORS
RIGHT CLIP
(Finish here.)
6 CLIPS
REAR
BUMPER
4 CLIPS
2 BOLTS
LEFT CLIP
(Start here.)
8 SELFTAPPING
SCREWS
•
BOLTS
3003063H
LICENSE PLATE
CENTER CLIP
(Second.)
4D19062H
Remove the antenna grommet from the roof,
unplug the vehicle connector, and remove the
rear roof trim.
18. Remove the rear roof trim:
2 HOOKS
•
•
Remove the roof trim nut covers (two retaining
tabs for each cover).
REAR
ROOF TRIM
Remove the two nuts.
HIGH-MOUNT
BRAKE LIGHT
GROMMET
ROOF TRIM
NUT COVER
2 RETAINING
TABS
2 NUTS
ANTENNA
GROMMET
4804024H
2 VEHICLE
CONNECTORS
REAR ROOF TRIM
4D19051H
6 of 17
AII 36587 (0705)
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
www.collegehillshonda.com
19. Remove and discard the grommets from the roof
panel, and install the six oval grommets and one
round grommet into the roof panel.
GROMMET
(Discard.)
21. Remove the left C-pillar outer trim (slide
rearward, and unplug the vehicle connector).
Remove the clips from the body, and reinstall the
clips to the left C-pillar outer trim.
ROUND
GROMMET
3 CLIPS
(Install.)
ROOF PANEL
3 CLIPS
(Remove.)
6 OVAL
GROMMETS
VEHICLE PANEL
LEFT C-PILLAR
OUTER TRIM
LEFT C-PILLAR
OUTER TRIM
VEHICLE
CONNECTOR
4611021H
6 GROMMETS
(Discard.)
4D20510K
22. Remove the left front anchor (two TORX bolts).
20. On the rear roof trim backside, remove and discard
the clips from the rear roof trim, and install the
seven clips to the rear roof trim.
LEFT FRONT
ANCHOR
REAR ROOF TRIM
7 CLIPS
T50 TORX
BOLTS
4610041H
4D20501K
7 CLIPS
(Discard.)
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
AII 36587 (0705)
7 of 17
www.collegehillshonda.com
23. Remove the front bed panel (six TORX bolts).
25. Remove the left lower bed light (one self-tapping
screw, pull the light out towards you and unplug
the vehicle connector).
LEFT LOWER
BED LIGHT
SELF-TAPPING
SCREW
CLIP
VEHICLE
CONNECTOR
FRONT BED
PANEL
6 T40 TORX
BOLTS
LEFT REAR
ANCHOR
T50 TORX
BOLT
3929032H
24. Remove the left bed rail trim:
•
Remove the screw cover (four retaining tabs).
•
Remove the self-tapping screw.
•
Pull the left bed rail trim back to release the
six clips, and remove the left bed rail trim.
3926062H
26. Remove the left rear anchor (two TORX bolts).
27. Remove the left side bed panel (six TORX bolts).
SCREW
COVER
4 RETAINING
TABS
6 CLIPS
LEFT SIDE
BED PANEL
LEFT BED
RAIL TRIM
SELFTAPPING
SCREW
6 T40 TORX
BOLTS
3926021H
LEFT BED
RAIL TRIM
3926071H
8 of 17
AII 36587 (0705)
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
www.collegehillshonda.com
28. Remove the tailgate trim:
30. Get the template. Using a scissors, cut out the
marked area from the template. Align the edge of
the template with the edge of the tailgate as
shown, and attach it to the tailgate tape.
•
Remove the four screws and release the one
end clip on each side.
•
Sharply push the tailgate to the right to release
the 16 clips from the trim.
•
OUTER
TAILGATE
Remove the 16 clips from the tailgate and
reinstall the 16 clips to the tailgate trim in the
direction shown.
TAILGATE
TRIM
CUT
TEMPLATE
16 CLIPS
TAILGATE
UPPER
HANDLE
TEMPLATE
9 TAPES
2 CLIPS
4707041K
TAILGATE TRIM
CUT
AREA
4605080T
4 SELFTAPPING
SCREWS
31. Center punch the tailgate at the marks on the
template. Remove the template.
29. Remove the tailgate panel (seven TORX screws).
7 T40 TORX
SCREWS
TAILGATE
4 MARKS
TAILGATE
PANEL
TAILGATE
UPPER
HANDLE
CENTER
PUNCH
4708010K
CUT
TEMPLATE
4605090T
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
AII 36587 (0705)
9 of 17
www.collegehillshonda.com
32. Drill three 8 mm holes and one 10 mm hole in the
tailgate.
•
Wrap tape around a 3 mm drill bit, and 8 mm
drill bit and a 10 mm drill bit 10 to 15 mm from
the end or use a drill stop.
•
While wearing eye protection, drill a 3 mm
hole, then an 8 mm hole in all four locations.
Drill a 10 mm hole only in the upper center
hole.
•
Remove any burrs, and apply touch-up paint
to all of the holes.
34. Remove the four screws from the rear camera.
Route the rear camera harness through the rear
camera subbracket, and install the rear camera
subbracket to the rear camera with the four
screws.
REAR
CAMERA
REAR CAMERA
SUBBRACKET
DRILL BIT
10 ~ 15 mm
TAPE
(Wrap tape around
the drill bit.)
UPPER
CENTER
HOLE
REAR CAMERA
HARNESS
TAILGATE
DRILL BIT
(3 mm 8 mm
10 mm)
4 SCREWS
4708050K
4 MARKS
35. Attach a piece of wire to the terminals from the
rear camera harness, and tape the wire to the
terminals.
4708021K
DRILL BIT
(3 mm 8 mm)
DRILL
33. Install one blind nut into each 8 mm hole.
REAR CAMERA
HARNESS
TAILGATE
TERMINALS
4913020K
BLIND
NUTS
10 of 17
3 8 mm
HOLES
4708030K
AII 36587 (0705)
TAPE
WIRE
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
www.collegehillshonda.com
36. Route the rear camera harness through the 10 mm
hole in the tailgate, and seat the grommet into the
10 mm hole.
38. Align the two locating tabs on the rear camera
subbracket with the slots in the rear camera
bracket, and install two 4 x 6 mm washer-screws.
NOTE: Make sure the flat surface of the rear camera
subbracket is facing up: otherwise, the camera view
will be upside down.
10 mm
HOLE
REAR CAMERA
HARNESS
4 x 6 mm
WASHER
SCREW
REAR CAMERA
BRACKET
GROMMET
WIRE
2 SLOTS
GROMMET
4 x 6 mm
WASHER
SCREW
4708071K
VEHICLE PANEL
REAR CAMERA
SUBBRACKET
(Flat surface
facing up.)
37. Install the rear camera bracket to the three blind
nuts with three 4 x 12 mm washer-screws.
4708081K
2 LOCATING
TABS
BLIND
NUT
TAILGATE PANEL
4708041K
4 x 12 mm
WASHER
SCREWS
REAR CAMERA
BRACKET
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
AII 36587 (0705)
11 of 17
www.collegehillshonda.com
39. Install clear adhesive tapes to the tailgate:
40. Route the rear camera harness along the tailgate
as shown.
•
Open the tailgate.
•
Get the clear adhesive tapes. Using scissors,
cut 30 mm from the end of each adhesive
tape.
•
Using isopropyl alcohol on a shop towel, clean
the tailgate where the adhesive tapes will
attach.
REAR CAMERA
HARNESS
TAILGATE
REAR
TAILGATE
4708092K
41. Remove the TORX bolt from the tailgate hinge, and
attach the harness clamp bracket B to the
tailgate using the TORX bolt you just removed. Do
not tighten the TORX bolt at this time.
REAR
T50 TORX BOLT
(Do not tighten at this time.)
HARNESS CLAMP
BRACKET B
30 mm
CLEAR
ADHESIVE
TAPE
TAILGATE
HINGE
30 mm
CLEAR
ADHESIVE
TAPE
SECOND
ADHESIVE TAPE
TAILGATE
TAILGATE
LIP
12 of 17
FIRST
ADHESIVE
TAPE
TAILGATE
5D10010T
4N09043K
AII 36587 (0705)
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
www.collegehillshonda.com
42. Secure the rear camera harness to the harness
clamp bracket B with three small wire ties. Attach
the wire tie over the tape attached to the
harness.
HARNESS
CLAMP
BRACKET B
45. Pull the rear camera harness out from the inside
of the tailgate, and secure the rear camera
harness to the harness clamp bracket A with one
small wire tie.
TAIL
GATE
T50 TORX BOLT
(Torque to 29 to32 N·m)
T50 TORX
BOLT
(Torque to
29 to32 N·m)
REAR
CAMERA
HARNESS
REAR
CAMERA
HARNESS
SMALL
WIRE TIE
TAPE
100 mm
25 mm
130 mm
SMALL
WIRE TIE
(Attach over
the tape.)
SMALL
WIRE TIE
HARNESS
CLAMP
BRACKET A
5D10020T
5D10041T
43. Torque the T50 TORX bolt to 29 to 32 N·m (21 to
23 lbs).
44. Close the tailgate. Remove the lower outboard
hinge bolt, and attach harness clamp bracket A to
the tailgate hinge with the TORX bolt you just
removed. Do not tighten the TORX bolt at this
time.
TAIL GATE
46. Torque the T50 TORX bolt to 29 to 32 N·m (21 to
23 lbs).
47. Using isopropyl alcohol on a shop towel, clean the
tailgate where the cushion tapes will attach. Using
scissors, cut one cushion tape in half. Secure the
rear camera harness to the tailgate with two half
cushion tapes and two full cushion tapes at the
locations shown.
CUSHION TAPE
REAR CAMERA
HARNESS
HARNESS
CLAMP
BRACKET A
TAILGATE
5D10030T
TAIL GATE
HINGE
T50 TORX BOLT
(Do not tighten at this time.)
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
AII 36587 (0705)
REAR
CUSHION TAPE
(Cut in half.)
4N09050K
13 of 17
www.collegehillshonda.com
51. Route the rear camera harness out through the
bed panel hole, and secure the rear camera
harness to the vehicle harness with one wire tie
just inside the panel hole.
48. Secure the rear camera harness to the tailgate
with five wire ties with clip.
TAILGATE
5 WIRE TIES
WITH CLIP
BED PANEL HOLE
TAILGATE
REAR
REAR
CAMERA
HARNESS
WIRE
TIE
FRONT
VEHICLE
HARNESS
CUSHION TAPE
(Cut in half.)
REAR CAMERA
HARNESS
4708103K
49. Using isopropyl alcohol on a shop towel, clean the
tailgate where the cushion tape will attach. Using
scissors, cut one cushion tape in half. Secure the
rear camera harness to the tailgate with one half
cushion tape.
50. Route the rear camera harness through the left
side vehicle panel hole, and secure the rear
camera harness to the vehicle harness with two
wire ties.
LEFT SIDE
VEHICLE
PANEL
4709050K
52. Route the rear camera harness along the vehicle
harness towards the front of the vehicle, and
secure it to the vehicle harness with six wire ties
in the areas shown.
REAR CAMERA
HARNESS
VEHICLE
HARNESS
6 WIRE TIES
LEFT SIDE
VEHICLE
PANEL HOLE
WIRE TIES
VEHICLE
HARNESS
5D10050T
REAR CAMERA
HARNESS
4709062K
14 of 17
AII 36587 (0705)
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
www.collegehillshonda.com
53. Remove the vehicle grommet from the left
C-pillar.
56. Inside the passenger’s compartment turn down the
rear panel insulator. Pull the rear camera harness
out from the hole in the C-pillar, and remove the
tape and wire from the rear camera harness.
LEFT C-PILLAR
BED BULKHEAD
VEHICLE
GROMMET
OPENING
REAR CAMERA
HARNESS
VEHICLE PANEL
OPENING
VEHICLE
GROMMET
FRONT
WIRE
TAPE
WIRE
6-PIN
CONNECTOR
6-PIN
CONNECTOR
REAR
CAMERA
HARNESS
LOCK
Harness side
view
6 TERMINALS
REAR
CAMERA
HARNESS
Red/
Red
GROMMET
54. Insert the rear camera harness through the
grommet, and route the rear camera harness
through the vehicle grommet opening. Seat the
grommet into the grommet hole.
57. Remove the lock from the 6-pin connector. Plug
the rear camera harness terminals into the 6-pin
connector as shown. Reinstall the lock.
55. Using electrical tape, secure the grommet to the
rear camera harness, and pay attention to the
angle of the grommet.
58. Get the rear camera subharness. Plug the rear
camera subharness 6-pin connector into the rear
camera harness 6-pin connector, and secure the
connected 6-pin connectors to the vehicle
connectors with two wire ties.
VEHICLE
CONNECTOR
GROMMET
WIRE TIE
FRONT
UP
2 WIRE
TIES
REAR
CAMERA
HARNESS
TAPE
VEHICLE
DOWN
GROMMET
OPENING
REAR CAMERA
HARNESS
6-PIN
CONNECTOR
REAR CAMERA
SUBHARNESS
6-PIN
CONNECTOR
C-PILLAR
GROMMET
4712012K
6-PIN
CONNECTOR
Yellow/
Black/
Blue/
Yellow
Black
Black
Brown
White/
White
4709071K
REAR CAMERA WIRE TIES
SUBHARNESS
4709080K
VEHICLE
HARNESS
4712031K
59. Route the rear camera subharness forward along
the vehicle harness, and secure the subharness
to the vehicle harness with five wire ties.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
AII 36587 (0705)
15 of 17
www.collegehillshonda.com
60. Continue routing the rear camera subharness
forward along the vehicle harness, and secure
the subharness to the vehicle harness with four
small wire ties.
62. Plug the rear camera subharness 6-pin connector
into the Navi control unit.
NAVI
CONTROL
UNIT
DRIVER’S
SEAT
VEHICLE
HARNESS
REAR CAMERA
SUBHARNESS
REAR CAMERA
SUB HARNESS
6-PIN CONNECTOR
FRONT
4713030K
63. Slide the driver’s seat back and forth to check that
the rear camera subharness is not pulled too tight
or is too loose.
4712041K
SMALL
WIRE
TIES
Check that the
rear camera
subharness is not
pulled too tight
when the seat is
moved back and
forth.
61. Route the rear camera subharness along the
vehicle harness and under the floor carpet, then
pull the rear camera subharness out from under
the floor carpet opening under the driver’s seat.
Secure the rear camera subharness to the
vehicle harness with two wire ties.
DRIVER’S
SEAT
DRIVER’S
SEAT
FLOOR CARPET
OPENING
4713040K
WIRE
TIES
VEHICLE
HARNESS
REAR CAMERA
SUBHARNESS
16 of 17
4N10010K
AII 36587 (0705)
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
www.collegehillshonda.com
64. Reconnect the negative cable to the battery. Turn
the key to the ON (II) position, and enter the Navi
code.
68. Measure and mark the rear bumper at the location
shown.
2 4 x 6 mm
WASHER SCREWS
REAR
BUMPER
REAR
CAMERA
Adjust the angle.
REAR CAMERA
TRIM
10 mm
15 mm
3 mm
4N15011K
REAR CAMERA
BRACKET
69. Using a utility knife, cut and remove measured
piece from the rear bumper. Remove any burrs
from the cut area with a file.
5D10060T
4 x 10 mm
SOCKET BOLTS
70. Reinstall the rear bumper.
71. Check that all wire harnesses are routed properly
and all connectors are plugged in.
65. Move the shift knob to the “R” position.
66. Loosen the two 4 x 6 mm washer-screws. Adjust
the rear camera angle up or down so that the end
of the rear bumper is reflected at the lowest
possible end of the navigation monitor. Tighten
the two 4 x 6 mm washer-screws. Install the rear
camera trim to the rear camera bracket with two 4
x 10 mm socket bolts.
67. Turn the key to the off position.
Cut off.
72. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
73. Set the clock.
74. Check the operation of the rear camera according
to the owner’s manual provided.
75. Put the rear camera Owner’s Manual in the glove
box with the vehicle owner’s manual.
76. Reinstall all removed parts.
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
77. Start the engine. Push down fully on the driver’s
window switch until the window is fully open.
78. Pull up fully on the driver’s window switch to close
the window completely, then hold the switch for
2 second or more.
79. Test the window AUTO function.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.
AII 36587 (0705)
17 of 17