Download GE A18201A Fact Sheet

GEA18201A X$D IEC_r11_GEA18201A X$D IEC 2/16/11 4:42 PM Page 1
GE Energy
X$D IEC
IE2 High Efficient Extra Severe Duty Motors
90-280 Frame
0.55-220 kW
50 Hz or 60 Hz
200 V-690 V
GEA18201A X$D IEC_r11_GEA18201A X$D IEC 2/16/11 4:42 PM Page 2
GE sets the standard...
Superior Performance
Proven Reliability
The X$D IEC meets or exceeds IE2 Nominal efficiencies.
For years severe duty motors from GE have proven their
• Overall vibration is 1.6 mm/sec. (0.063 in. per second). This
performance and reliability in the most demanding process
helps to extend the life of the motor and the connected
industry environments.
equipment.
• A one-year warranty comes standard with every X$D IEC
motor. (12 months operational/18 months maximum from
• Total shaft runout is 0.025 mm (0.001 in.) for shaft diameters
shipment.)
up to 41 mm and 0.038 mm (0.0015 in.) for shaft diameters
greater than 41 mm for ball bearing machines.
• Cast-in vibration pads provide five-point vibration probe
mounting (four radial, one axial).
• GEGARD2400™ insulation systems features Class H
insulation materials. This system increases motor protection
against IGBT drive voltage spikes that typically can reach
2,400 volts @ 0.1 microsecond rise time, which exceeds
NEMA MG1-31 standards.
• Rugged cast iron frame, conduit box, endshields, and fan cover.
Inverter Duty Application
The GEGARD2400™ insulation system exceeds
the NEMA MG1-31 specifications andEXthe
Bearings
GEGARD2400 TM
INVERTER
DUTY
requirements of the IEC 60034-17 and 60034-18-41
EXCEEDS
NEMA
MG1-31
GE’s Bearing System assures the maximum possible bearing
standards. It has the ability to withstand repeated 0.1 microsecond
life when combined with a maintenance program. For optimum
rise time that typically can reach 2400 volt spikes for up to 575
performance, the same over-sized bearing is used on both
line voltages.
ends of the motor.
•
(-40°C to +130°C).
Infinite:1 variable torque speed range and 10:1 constant
* Some exceptions apply to constant torque speed ranges. Contact
GE Energy to verify capability on specific ratings.
drive-end and opposite drive-end ensuring IP55 protection.
polyurea grease suitable for a wide temperature range
•
All motors are tested to verify the Corona Inception Voltage
(CIV) at the factory before shipment.
• An oversized single-shielded bearing is open towards the
grease cavity for maximum lubricant circulation.
• 130,000 hours minimum bearing life for direct-drive loads,
and 26,280 hours for L10 belt-driven loads.
• A gasketed cast-iron inner bearing cap retains lubricant and
protects the bearing system and interior of the motor from
contaminants.
• Finned endshield for improved heat dissipation and long
bearing life (200-280 frame)
EX
torque* speed range available on request.
• A steel-reinforced recessed slinger is integrated to both the
• Fully charged lubrication system with a temperature-resistant
EX
add ---period
IE2 Efficiency
GEA18201A X$D IEC_r11_GEA18201A X$D IEC 2/16/11 4:42 PM Page 3
...with powerful features
Serviceability
Even the best motors need service. Our design engineers have
made improvements to help make service easy.
• An over-sized gasketed conduit box, containing permanently
labeled non-wicking Class H leads to a terminal board, makes
connection and installation easy.
• Dual mounting holes for application versatility and
reduced inventory.
• Stainless steel combination breather/drains allow
condensation to drain from motor.
• Corrosion-resistant ISO Grade 8.8 metric hardware is
rugged and designed for ease of motor service.
• Embossed 316 stainless steel nameplate stamped with over
30 motor specification details and all applicable standards.
• Leads are sleeved and are compatible with an oil mist
• Stator core centered in frame for easy conversion of a top
or side mounted conduit box for power connections on either
side of the motor (except on some FF flange constructions).
• Raised-letter embossed 316 stainless steel nameplate
with superior operational and maintenance information.
Superior Corrosion Protection
The motor frame, fan cover, endshield, and conduit box are cast
iron for severe duty. Rotor surfaces are coated to resist interior
rust, which helps maintain performance.
• Epoxy ester paint system stands up to corrosive
environments.
lubrication system.
Safety
GE has added features that make this product safe to install,
operate, and maintain.
• Safer lifting is possible with a four-point lifting system
versus a single eyebolt.
• Cast-in lifting lugs eliminate eyebolts that may strip, shear,
get lost, or be improperly selected.
• Grease inlet fitting at twelve o'clock and outlet fitting at eight
o'clock or four o’clock position, which promotes safer
regreasing.
• Non-sparking, corrosion-resistant bidirectional fan* is quiet
and energy efficient.
* Two-pole motor fans are unidirectional in 280 K and H frame sizes.
• A silicon bronze box lug earthing terminal is located in the
conduit box. Additional earthing terminal posts are
located toward the drive-end on both sides of the frame
for greater operational safety.
• Fan covers on frames 200-280 have axial mounting bolts
for more rugged installation.
X$D IEC meets these challenges.
Improved Customer Operating Performance
• The X$D IEC meets or exceeds the requirements for most
industry specifications in IEC construction. With an advanced
insulation and bearing system, one-year warranty and all
the advanced features that come with it, the X$D IEC is the
most durable and reliable , to ensure high reliability and
durability over the life of the motor.
.
GEA18201A X$D IEC_r11_GEA18201A X$D IEC 2/16/11 4:42 PM Page 4
X$D IEC 50 Hz (IE2 Efficiency – Type KFE)
Typical Performance Data at 400 Volts
Output
kW
Frame
0.55
0.55
0.55
0.55
0.75
0.75
0.75
0.75
1.1
1.1
1.1
1.1
1.5
1.5
1.5
1.5
2.2
2.2
2.2
2.2
3
3
3
3
3.7
3.7
3.7
3.7
4
4
4
4
5.5
5.5
5.5
5.5
7.5
7.5
7.5
7.5
11
11
11
11
15
15
15
15
18.5
18.5
18.5
18.5
22
22
22
22
30
30
30
30
37
37
37
37
45
45
45
45
55
55
55
55
75
75
75
75
90
90
90
90
110
110
110
110
132
132
132
160
160
160
200
220
90S
90S
90S
90L
90S
90S
90S
112S
90S
90L
112S
112S
90L
90L
112M
112M
112S
112S
112M
132S
112S
112S
132S
132M
112M
112M
132M
160M
112M
112M
132M
160M
132S
132S
132M
160M
132S
132M
160M
160L
160M
160M
160L
180M
160M
160L
180L
200M
160L
180M
200L
225S
180M
180L
200L
225S
200M
200M
225M
250S
200M
200L
250M
250M
225S
225S
280S
280S
225M
225M
280M
280M
250M
250M
280M
280M
280M
280S
280K
280K
280M
280M
280K
280H
280K
280K
280K
280H
280H
280H
280H
280H
NP
Cat
FL RPM
Amps IN
Number
(A)
2930
1435
945
700
2910
1425
945
725
2905
1420
970
715
2915
1410
960
700
2940
1455
960
725
2935
1460
975
720
2930
1455
970
725
2925
1450
970
730
2920
1465
960
730
2940
1460
970
725
2955
1470
965
735
2945
1470
975
725
2965
1480
985
740
2960
1475
980
740
2965
1475
985
735
2960
1480
995
735
2970
1480
995
740
2970
1480
995
740
2975
1485
990
740
2985
1480
900
740
2975
1490
990
740
2980
1490
990
2980
1490
995
1490
1490
N902
N901
N900
N971
N905
N904
N903
N972
N908
N907
N906
N973
N911
N910
N909
N974
N914
N913
N912
N975
N917
N916
N915
N976
N920
N919
N918
N977
N923
N922
N921
N978
N926
N925
N924
N979
N929
N928
N927
N980
N932
N931
N930
N981
N935
N934
N933
N982
N938
N937
N936
N983
N941
N940
N939
N284
N944
N943
N942
N985
N947
N946
N945
N986
N950
N949
N948
N987
N953
N952
N951
N988
N956
N955
N954
N989
N958
N957
N967
N990
N960
N959
N968
N991
N961
N963
N969
N962
N964
N970
N965
N966
1.3
1.2
1.6
2.3
1.8
1.7
2.1
2.8
2.4
2.3
3.0
3.7
3.3
3.1
4.0
4.6
4.7
5.0
5.6
6.6
6.1
6.7
7.3
9.2
7.3
8.3
8.5
9.5
8.0
8.8
9.3
10.6
10.6
11.5
12.3
14.5
13.7
15.2
16.3
18.2
20.4
21.1
21.7
25.2
26.9
27.5
28.4
35.0
32.8
37.0
39.1
41.9
39.0
43.8
47.9
47.8
56.0
57.2
57.6
66.5
67.5
71.5
75.2
77.9
85.3
83.5
88.7
94.2
98.4
101.0
107.0
112.0
129.0
137.0
141.0
151.0
155.0
160.0
168.0
176.0
187.0
193.0
199.0
221.0
221.0
233.0
241.0
264.0
276.0
289.0
349.0
380.0
Start/
Full
Load
Amps
IS/IN
7.8
6.6
5.0
3.7
6.9
6.0
5.3
4.6
7.7
6.4
7.2
4.4
8.0
6.2
6.4
4.1
7.3
6.5
6.6
5.3
6.9
6.7
6.4
5.3
6.7
6.6
5.8
5.0
6.6
6.2
5.9
5.2
6.1
6.5
5.6
5.4
8.5
5.9
5.6
5.0
6.6
5.7
5.5
7.0
6.4
6.0
6.3
4.5
9.1
6.8
6.3
4.7
7.5
6.4
5.5
4.6
5.2
4.8
5.4
5.7
5.1
5.7
5.9
5.4
5.4
5.6
6.3
4.9
5.9
5.7
6.3
4.8
7.6
4.8
5.9
5.3
7.3
4.9
5.9
5.4
5.7
6.1
5.6
6.3
6.2
5.5
5.9
6.5
6.0
6.6
6.2
6.6
BreakStart/
Full
Starting down
Full
Load
Torque Torque
Load
Torque
Torque TN (Nm) TS (Nm) Tmax
(Nm)
TS/TN
2.8
3.0
2.5
2.8
2.4
2.8
2.8
2.0
2.7
2.8
2.3
1.9
3.1
2.8
2.2
1.6
2.0
2.4
2.2
2.2
1.9
2.5
2.1
2.3
1.8
2.5
1.9
1.8
1.8
2.3
1.9
2.0
2.0
2.0
1.9
2.2
3.1
1.8
2.0
1.9
2.2
2.1
2.0
2.3
2.3
2.2
2.1
1.7
3.8
2.0
1.8
1.5
3.1
1.9
2.2
1.4
1.5
1.5
1.5
1.9
1.5
1.8
1.6
1.7
1.4
1.6
1.4
1.4
1.6
1.6
1.5
1.4
2.0
1.4
1.4
1.6
1.7
1.6
1.5
1.6
1.3
1.2
1.4
2.0
1.4
1.1
1.5
1.6
1.2
1.7
1.3
1.4
1.8
3.7
5.6
7.5
2.5
5.0
7.6
9.9
3.6
7.4
10.8
14.7
4.9
10.2
14.9
20.4
7.1
14.4
21.9
29.1
9.8
19.6
29.4
39.8
12.1
24.2
36.5
48.5
13.1
26.3
39.4
52.4
18.0
35.8
54.6
72.0
24.3
49.1
73.9
99.0
35.6
71.5
109.0
142.9
48.6
97.5
147.1
197.4
59.6
119.4
179.4
238.7
71.0
142.2
214.8
284.0
96.5
193.9
290.0
388.7
119.2
238.5
355.6
480.7
144.7
290.0
432.2
580.1
176.8
354.4
528.4
709.9
240.7
482.0
721.3
967.1
287.9
580.0
865.8
1161.4
352.7
704.6
1059.1
1415.8
422.9
845.6
1270.6
512.5
1024.2
1538.5
1279.9
1407.5
5.0
10.8
14.0
20.6
6.0
14.0
21.1
19.5
9.8
20.9
24.5
27.3
15.5
28.9
32.5
33.6
14.1
34.4
48.9
64.7
18.2
48.5
62.4
91.6
22.2
60.7
67.7
85.4
23.9
60.7
76.7
103.4
36.1
70.8
101.4
155.6
75.0
88.4
150.8
186.8
78.5
149.4
213.1
333.0
113.5
219.1
302.9
337.4
226.1
234.1
314.0
351.3
217.3
264.8
475.0
399.4
140.5
292.2
430.6
726.3
176.0
432.3
571.9
827.0
205.0
453.4
617.4
803.3
280.7
570.9
777.7
958.5
481.6
664.0
992.5
1511.4
483.7
946.0
1268.2
1861.7
461.2
826.1
1481.3
2827.3
587.4
921.0
1904.1
795.6
1272.6
2659.0
1659.8
1958.2
690 V Ratings are also available - Contact GE for details
6.5
12.9
17.2
24.9
7.7
16.8
25.5
29.8
11.9
24.1
42.4
38.8
18.0
32.7
53.7
47.7
23.5
45.8
79.2
98.7
29.8
62.4
90.0
136.1
35.7
76.9
96.8
129.7
38.2
76.9
108.9
154.6
46.4
100.1
139.9
225.9
81.1
123.1
200.7
268.7
91.5
184.1
263.0
478.7
117.8
246.7
370.8
449.7
194.0
341.5
513.4
570.0
221.0
376.8
574.2
645.7
220.6
428.3
709.6
1231.6
256.5
616.4
957.2
1382.5
350.1
711.0
1231.3
1434.7
433.5
875.5
1500.1
1666.1
742.3
1048.7
1854.9
2490.5
896.7
1361.7
2424.2
3003.0
849.5
1812.6
2739.8
4429.6
1185.3
2073.9
3477.0
1473.7
2642.4
4660.1
3402.4
3916.4
NP Eff.
Full
Load
75%
Load
Eff.
50%
Load
Eff.
NP PF
Full
Load
Max
KVAR
77.2
79.9
74.0
67.0
78.9
81.1
76.0
71.8
80.8
82.7
78.3
74.7
82.6
83.9
79.9
74.4
84.0
85.3
81.9
82.9
85.3
86.3
83.5
81.3
86.4
87.3
84.7
82.4
86.4
87.3
84.7
84.1
87.5
88.2
86.1
84.7
88.5
89.1
87.3
86.1
89.6
90.1
88.7
86.8
90.5
90.9
89.7
90.2
91.0
91.4
90.4
91.0
91.4
91.7
90.9
91.6
92.1
92.4
91.7
92.4
92.5
92.8
92.2
92.7
92.9
93.1
92.7
93.2
93.3
93.5
93.1
93.4
93.9
94.0
93.7
93.7
94.2
94.4
94.2
94.1
94.5
94.7
94.5
94.5
94.9
94.9
94.8
95.2
95.2
95.1
95.1
96.0
82.3
85.2
81.1
66.6
85.6
82.7
81.3
76.2
88.1
86.9
87.5
77.6
86.6
86.2
84.1
76.8
89.8
88.4
84.7
82.8
90.6
89.4
88.7
82.6
91.0
89.2
88.4
86.9
90.9
88.9
88.3
86.1
89.9
90.9
88.3
86.9
92.6
90.8
89.4
87.5
92.2
91.9
91.3
90.2
92.6
93.3
91.4
91.0
94.3
93.1
93.4
93.5
93.6
92.6
92.4
94.1
94.3
94.6
95.0
93.6
94.5
95.0
94.9
94.0
94.8
94.9
94.7
93.7
95.6
94.9
95.0
94.2
95.9
96.1
95.4
94.8
95.8
96.0
95.4
95.0
95.7
96.4
95.6
95.2
95.9
96.5
95.8
96.2
96.9
96.2
96.6
96.7
79.0
84.1
79.5
60.8
84.6
81.4
79.6
71.9
88.0
87.3
86.1
74.6
85.3
86.9
82.3
75.2
88.6
87.6
83.5
80.2
90.0
88.5
87.8
80.3
90.8
88.4
88.2
85.8
90.8
88.6
87.9
84.4
90.0
90.5
88.6
85.2
92.5
91.0
88.9
86.8
92.2
92.0
92.0
89.7
93.1
93.7
92.1
90.6
94.3
92.7
92.8
92.8
93.3
92.2
91.8
93.6
93.7
94.6
94.8
92.7
94.3
94.8
94.2
93.6
94.2
95.0
93.9
93.0
95.2
94.8
94.3
93.7
95.8
96.1
95.0
94.3
95.2
95.9
95.2
94.8
95.5
96.4
95.7
94.8
95.8
96.5
95.7
96.2
96.8
96.1
96.4
96.4
78.5
79.5
68.0
50.5
78.0
76.5
66.5
53.5
83.0
84.0
68.5
58.0
78.5
83.5
67.5
63.0
80.5
74.0
69.5
58.0
83.0
74.5
71.0
58.0
84.5
74.0
74.5
68.5
83.5
75.5
73.0
65.0
86.0
78.5
75.0
64.5
89.0
80.0
76.0
69.0
87.0
83.5
82.5
72.5
89.0
86.5
85.0
68.5
89.5
79.0
75.5
70.0
89.0
79.0
73.0
72.5
84.0
82.0
82.0
70.5
85.5
80.5
77.0
74.0
82.0
83.5
79.0
74.0
86.5
84.0
79.5
76.0
89.5
84.0
82.0
76.5
89.0
86.0
82.0
78.5
90.0
87.0
84.5
76.0
91.0
86.0
83.5
92.0
88.0
84.0
87.0
87.0
0.4
0.4
0.6
1.1
0.5
0.6
0.8
1.2
0.5
0.5
1.0
1.5
0.9
0.8
1.5
1.8
1.2
1.6
2.1
2.9
1.3
2.1
2.5
3.9
1.5
2.6
2.6
3.4
1.7
2.6
3.0
4.2
2.3
3.2
3.7
5.9
2.7
3.8
5.2
6.7
3.9
5.3
5.0
8.3
4.1
5.4
6.5
12.0
5.4
10.9
11.9
14.1
7.8
12.9
15.4
14.8
12.2
13.5
13.9
23.8
12.9
18.8
22.4
25.5
21.3
19.9
25.3
29.7
19.9
23.6
29.8
32.2
23.5
29.3
34.9
44.1
29.2
31.9
41.4
47.3
27.5
38.0
42.3
67.8
30.3
45.8
54.0
33.5
49.0
65.8
66.2
75.1
MoApprox
ment of Motor
Inertia J Mass
(Kgm2)
(kgs)
0.0013
0.0032
0.0043
0.0048
0.0013
0.0029
0.0049
0.0128
0.0018
0.0052
0.0151
0.0146
0.0020
0.0052
0.0113
0.0165
0.0062
0.0113
0.0151
0.0347
0.0073
0.0142
0.0321
0.0420
0.0083
0.0161
0.0340
0.0668
0.0083
0.0161
0.0359
0.0668
0.0137
0.0340
0.0434
0.0891
0.0217
0.0397
0.0737
0.1069
0.0457
0.0869
0.1335
0.3132
0.0571
0.1326
0.2900
0.4313
0.0828
0.1926
0.4458
0.8853
0.1170
0.2000
0.4829
1.0750
0.1769
0.3611
1.2420
1.4548
0.2010
0.4581
1.3482
1.7558
0.2805
0.5991
2.7867
2.2933
0.3569
0.6878
3.2154
2.7103
0.6219
1.2281
3.8585
3.9612
1.1939
2.9820
4.3549
5.2121
1.1598
3.2802
5.3918
7.2970
1.4520
3.3897
6.2214
1.8480
4.7601
8.9173
5.1928
5.7698
23
23
23
23
23
23
23
46
23
23
46
46
23
23
46
46
46
46
46
100
46
46
100
100
46
46
100
130
46
46
100
130
100
100
100
130
100
100
130
130
130
130
130
200
130
130
200
365
130
200
365
524
200
200
365
524
365
365
524
721
365
365
721
721
524
524
998
998
524
524
998
998
721
721
998
998
998
998
1430
1430
998
998
1430
1430
1430
1430
1430
1430
1430
1430
1430
1430
IEC T
Sound
Block
Pres(@460 V)
sure
6 Stud
dB(A)
IEC
70
58
55
60
70
58
55
62
70
58
62
62
70
58
62
62
75
64
62
63
75
64
65
63
75
64
65
63
75
64
65
63
77
67
65
63
77
67
65
63
79
69
65
68
79
69
69
71
79
72
72
71
80
72
72
71
82
75
72
72
82
75
74
72
84
76
77
74
84
76
77
74
84
77
77
74
86
80
80
74
86
80
80
74
88
80
80
88
80
80
89
89
M4
M4
M4
M4
M4
M4
M4
M6
M4
M4
M6
M6
M4
M4
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M8
M6
M6
M8
M8
M6
M6
M8
M8
M8
M8
M8
M8
M8
M8
M10
M10
M8
M8
M10
M10
M8
M8
M10
M10
M8
M8
M10
M10
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
GEA18201A X$D IEC_r11_GEA18201A X$D IEC 2/16/11 4:43 PM Page 5
X$D IEC 60 Hz (IE2 Efficiency – Type KFE)
Typical Performance Data at 460 Volts
Output
kW
Frame
FL RPM
0.55
0.55
0.55
0.55
0.75
0.75
0.75
0.75
1.1
1.1
1.1
1.1
1.5
1.5
1.5
1.5
2.2
2.2
2.2
2.2
2.2
3
3
3
3
3.7
3.7
3.7
3.7
4
4
4
4
5.5
5.5
5.5
5.5
7.5
7.5
7.5
7.5
11
11
11
11
15
15
15
15
18.5
18.5
18.5
18.5
22
22
22
22
30
30
30
30
37
37
37
37
45
45
45
45
55
55
55
55
75
75
75
75
90
90
90
90
110
110
110
110
132
132
132
132
160
160
160
200
220
90S
90S
90S
90L
90S
90S
90S
112S
90S
90L
112S
112S
90L
90L
112M
132S
90L
112S
112S
112M
132S
112S
112S
132M
132M
112M
112M
132M
160M
112M
112M
132M
160M
132S
132S
132M
160M
132M
132M
160M
160L
160M
160M
160L
180M
160M
160L
180L
200M
160L
180M
200L
200L
180M
180L
200L
225S
200M
200M
225M
225M
200M
200L
250M
250M
225S
225S
280S
280S
225M
225M
280M
280M
250M
250M
280M
280M
280M
280S
280K
280K
280M
280M
280K
280K
280K
280K
280K
280H
280H
280K
280H
280H
280H
3520
1730
1145
845
3515
1720
1140
875
3500
1720
1170
870
3500
1725
1165
875
3480
3540
1765
1165
880
3540
1755
1170
875
3540
1755
1170
880
3535
1750
1170
880
3535
1770
1175
885
3525
1760
1170
880
3555
1770
1175
885
3550
1770
1180
880
3550
1775
1180
875
3555
1775
1175
890
3570
1780
1185
885
3565
1780
1195
890
3570
1780
1195
890
3570
1780
1195
890
3570
1785
1190
890
3580
1785
1195
890
3580
1790
1190
890
3585
1790
1190
890
3580
1790
1195
1795
1790
NP
Cat
Amps IN
Number
(A)
N350
N356
N364
N372
N351
N357
N365
N373
N352
N358
N366
N374
N353
N359
N367
N375
N203
N202
N201
N300
N376
N206
N205
N204
N377
N395
N394
N207
N378
N398
N397
N396
N379
N315
N314
N313
N380
N318
N317
N316
N381
N321
N320
N319
N382
N324
N323
N322
N383
N327
N326
N325
N384
N330
N329
N328
N385
N263
N262
N261
N386
N266
N335
N264
N387
N269
N338
N337
N388
N342
N341
N340
N389
N345
N344
N343
N390
N347
N346
N368
N391
N349
N348
N369
N392
N354
N360
N370
N393
N355
N361
N371
N362
N363
1.1
1.1
1.4
1.9
1.5
1.5
1.7
2.5
2.0
2.1
2.4
3.3
2.7
2.8
3.0
3.9
3.9
4.0
4.1
4.5
6.0
5.2
6.0
5.9
7.8
6.3
7.2
7.2
8.3
6.9
7.3
7.6
9.4
9.1
10.0
10.9
13.0
11.8
12.9
13.4
15.9
17.5
17.9
20.3
20.9
23.5
24.3
28.4
31.4
28.5
30.3
35.2
38.2
34.1
35.8
39.6
43.0
48.2
50.6
49.4
55.9
58.4
60.9
65.3
75.0
71.0
71.4
73.6
84.4
86.3
86.8
92.8
107.0
112.0
119.0
123.0
141.0
135.0
141.0
145.0
154.0
163.0
167.0
173.0
184.0
194.0
202.0
205.0
220.0
230.0
239.0
249.0
305.0
329.0
Start/
Full
Load
Amps
IS/IN
7.6
6.9
5.2
3.8
7.6
6.9
5.3
5.0
7.7
7.4
7.6
5.0
7.4
7.3
6.9
5.1
7.1
7.6
7.5
7.5
5.9
7.5
6.5
6.3
5.7
7.6
6.6
6.4
5.5
7.5
6.2
6.4
5.8
7.1
7.2
7.0
6.0
7.0
6.2
6.5
5.6
6.7
5.9
7.3
6.9
7.0
6.6
5.8
5.1
7.4
6.4
5.5
4.8
6.9
6.7
5.6
5.0
5.9
5.1
5.3
4.4
5.4
5.2
6.1
6.4
6.0
5.1
6.5
5.6
6.1
5.8
6.3
5.6
7.1
4.6
5.9
5.9
6.4
5.8
6.3
5.5
5.9
6.3
6.1
5.2
7.0
6.3
6.1
5.1
6.8
6.1
6.5
7.0
6.6
BreakStart/
Full
Starting down
Full
Load
Torque Torque
Load
Torque
Torque TN (Nm) TS (Nm) Tmax
(Nm)
TS/TN
2.2
2.9
2.5
2.2
2.3
2.9
2.4
2.0
2.4
3.2
2.1
2.0
2.4
3.2
1.9
1.7
2.4
2.0
2.7
2.3
2.3
2.0
2.4
1.9
2.2
2.1
2.4
1.9
1.9
2.0
2.2
1.9
2.1
2.1
2.2
2.3
2.3
2.1
1.9
2.2
2.0
2.0
2.1
2.8
2.0
2.3
2.4
1.7
1.8
2.5
1.8
2.0
1.8
2.6
1.9
2.1
1.6
1.6
1.6
1.4
1.3
1.5
1.7
1.6
2.2
1.5
1.4
1.4
1.6
1.6
1.7
1.4
1.7
1.7
1.3
1.4
1.8
1.3
1.6
1.6
1.6
1.2
1.2
1.6
1.5
1.6
1.3
1.6
1.5
1.7
1.3
1.7
1.5
1.4
Contact GE for details on additional ratings
1.5
3.0
4.6
6.2
2.0
4.2
6.3
8.2
3.0
6.1
9.0
12.0
4.1
8.3
12.3
16.4
6.0
5.9
11.9
18.0
23.9
8.1
16.3
24.4
32.8
10.0
20.1
30.2
40.1
10.8
21.8
32.6
43.3
14.9
29.6
44.8
59.5
20.3
40.6
61.1
81.5
29.5
59.4
89.5
118.7
40.3
80.8
121.2
162.7
49.7
99.4
149.8
201.6
59.1
118.2
178.4
235.9
80.2
161.0
241.3
322.8
99.1
198.6
296.0
397.7
120.3
241.5
359.8
481.6
147.0
294.8
439.9
588.7
200.4
401.1
600.3
803.0
239.9
481.7
720.1
965.4
293.4
586.4
880.5
1181.7
351.6
703.3
1056.8
1418.8
426.5
852.7
1280.5
1064.8
1171.7
3.3
8.9
11.5
13.4
4.7
12.2
15.2
16.0
7.2
19.5
19.0
23.6
9.8
26.3
23.9
28.3
14.6
11.8
31.9
41.1
54.9
16.1
39.5
46.0
72.5
20.5
49.2
57.1
75.4
22.1
48.0
61.8
91.6
30.6
66.0
103.2
138.0
43.1
75.4
137.3
165.3
58.0
121.7
250.3
238.9
90.7
196.2
202.4
300.6
126.6
174.9
303.1
352.9
153.6
220.6
370.8
369.7
125.8
254.3
346.7
420.7
144.5
329.0
477.1
864.0
174.9
333.8
514.2
752.8
232.4
487.0
630.4
994.0
339.8
541.1
820.2
1431.7
322.4
780.9
1139.0
1540.0
362.4
697.1
1378.4
1767.2
545.7
886.1
1662.7
2100.5
743.5
1073.2
2208.4
1566.4
1633.3
4.7
11.5
15.0
17.4
6.6
15.2
19.7
27.0
9.8
23.5
36.2
36.6
12.9
31.0
43.5
49.2
18.6
20.2
41.2
71.2
90.4
26.4
51.2
70.0
117.1
32.8
62.5
84.2
119.6
35.2
60.7
90.4
143.6
43.4
91.2
142.8
209.5
55.6
103.0
175.4
248.4
76.1
147.6
298.8
359.5
103.3
219.9
328.0
411.5
131.9
256.0
394.4
477.2
165.0
309.1
445.2
585.1
203.5
375.1
558.3
656.7
221.4
455.7
811.1
1445.9
302.1
525.8
995.0
1325.9
372.0
720.7
1234.1
1715.2
575.1
848.7
1532.0
2337.7
656.5
1232.6
2093.1
2459.7
725.6
1537.0
2464.8
2767.4
1122.2
1933.6
2870.4
3231.8
1263.8
2189.9
3714.2
3198.8
3229.3
NP Eff.
Full
Load
75%
Load
Eff.
50%
Load
Eff.
NP PF
Full
Load
Max
KVAR
74.0
81.5
78.5
67.0
80.0
82.5
80.0
74.0
82.5
84.0
85.5
77.0
84.0
84.0
86.5
82.5
85.0
85.5
87.5
87.5
84.0
87.5
87.5
87.7
84.5
87.5
87.5
87.5
85.5
87.5
88.5
88.5
85.5
88.5
89.5
89.5
85.5
89.5
89.5
89.5
88.5
90.2
91.0
90.2
88.5
90.2
91.0
90.2
89.5
91.0
92.4
91.7
89.5
91.0
92.4
91.7
91.0
93.0
93.0
93.0
91.0
92.4
93.0
93.0
91.7
93.0
93.6
93.6
91.7
93.0
94.1
93.6
93.0
93.6
94.5
94.1
93.0
94.5
94.5
94.1
93.6
94.5
95.0
95.0
93.6
95.0
95.0
95.0
93.6
95.0
95.0
95.0
95.0
95.4
86.4
83.0
79.0
71.4
87.2
84.5
81.6
78.7
88.1
86.4
88.4
79.9
85.5
86.6
87.8
83.1
86.1
91.3
90.7
88.3
84.4
90.4
88.1
88.7
84.7
91.1
89.4
89.5
88.2
91.2
89.9
89.6
87.6
90.5
91.4
90.0
88.3
91.4
91.5
90.4
89.2
92.1
92.6
90.5
91.5
93.0
93.4
91.6
92.0
93.3
93.5
92.1
91.3
93.1
93.8
93.1
94.1
93.9
94.4
94.8
94.1
94.3
94.9
94.6
93.6
95.0
94.9
94.5
94.0
95.4
95.4
94.5
93.4
95.7
96.0
95.0
94.3
95.7
95.5
95.5
95.2
95.8
96.3
95.6
95.3
95.5
96.4
95.9
95.5
95.9
96.6
96.1
96.3
96.4
84.8
80.9
76.2
67.2
86.0
83.3
79.9
74.2
87.6
85.8
86.7
76.3
84.2
85.9
86.7
80.5
85.5
90.5
89.7
87.1
81.4
89.1
86.7
87.8
82.2
90.0
88.4
88.9
86.4
90.2
89.5
89.1
85.3
89.6
90.4
89.1
86.2
91.2
91.4
89.8
88.0
91.6
92.6
89.6
91.1
92.8
93.3
90.7
91.0
93.3
93.3
91.1
90.5
92.5
93.6
92.6
93.3
92.8
94.0
94.5
93.7
93.6
94.7
93.6
92.2
94.1
94.9
93.4
92.9
94.7
95.3
93.5
92.0
95.3
95.9
94.3
93.2
95.2
95.2
95.0
94.8
95.6
96.1
95.3
95.2
94.8
96.2
95.7
95.5
95.5
96.6
95.8
95.7
95.9
82.0
74.5
64.5
55.5
81.0
78.0
68.5
50.5
82.5
80.0
68.5
54.0
84.0
79.5
71.5
59.0
83.0
80.0
77.0
70.0
55.0
83.5
71.5
72.5
57.0
84.0
74.0
74.0
65.5
83.5
77.5
74.5
62.5
86.0
77.5
71.0
62.0
89.0
81.5
78.5
67.0
87.5
85.0
75.5
74.5
89.0
85.0
73.5
67.0
89.5
83.0
72.0
68.0
89.0
83.5
76.0
70.5
84.0
80.0
82.0
74.0
86.0
82.0
76.5
67.5
85.5
84.5
82.0
73.0
86.0
84.5
79.5
69.5
89.5
83.5
81.5
72.0
88.5
85.0
83.0
78.5
89.5
87.0
84.0
80.0
90.0
86.5
85.0
80.5
92.0
88.5
85.0
86.5
88.0
0.3
0.5
0.6
0.9
0.4
0.5
0.7
1.3
0.5
0.7
1.0
1.6
0.7
1.0
1.2
1.9
1.1
1.2
1.4
1.8
3.1
1.3
2.4
2.3
3.9
1.5
2.6
2.6
3.7
1.7
2.3
2.7
4.5
2.3
3.3
4.4
6.2
2.4
3.5
4.6
7.1
3.6
4.5
7.8
7.2
4.1
6.2
10.8
12.8
5.0
8.6
13.5
15.1
7.3
10.0
13.1
16.3
12.7
15.2
13.2
18.0
12.8
16.5
22.9
33.1
17.5
17.2
21.2
31.1
20.4
22.1
30.2
44.8
21.6
29.1
35.6
53.9
28.4
36.4
39.8
46.4
30.3
38.2
45.2
50.0
36.8
47.7
48.4
56.3
33.2
47.2
61.3
73.7
68.9
MoApprox
ment of Motor
Inertia J Mass
(Kgm2)
(kgs)
0.0013
0.0024
0.0028
0.0040
0.0013
0.0028
0.0042
0.0128
0.0015
0.0039
0.0146
0.0146
0.0017
0.0043
0.0128
0.0219
0.0020
0.0057
0.0123
0.0180
0.0347
0.0073
0.0113
0.0264
0.0420
0.0083
0.0132
0.0321
0.0668
0.0083
0.0137
0.0340
0.0668
0.0137
0.0321
0.0434
0.0891
0.0171
0.0378
0.0737
0.1069
0.0428
0.0823
0.1013
0.3132
0.0542
0.1097
0.2471
0.4313
0.0628
0.1704
0.3715
0.4493
0.0975
0.2000
0.4458
0.9486
0.1769
0.3055
1.0459
1.0750
0.1930
0.3888
1.1926
1.5551
0.2933
0.5325
3.1082
2.2933
0.3315
0.6656
2.7867
2.3976
0.5830
1.0527
3.3226
3.3358
0.9551
1.9383
4.3549
4.4824
1.0575
3.0566
5.0808
5.6291
1.3860
3.3176
6.8435
7.2970
1.8480
4.2552
8.3988
5.0485
5.6255
23
23
23
23
23
23
23
46
23
23
46
46
23
23
46
100
23
46
46
46
100
46
46
100
100
46
46
100
130
46
46
100
130
100
100
100
130
100
100
130
130
130
130
130
200
130
130
200
365
130
200
365
365
200
200
365
524
365
365
524
524
365
365
721
721
524
524
998
998
524
524
998
998
721
721
998
998
998
998
1430
1430
998
998
1430
1430
1430
1430
1430
1430
1430
1430
1430
1430
1430
IEC T
Sound
Block
Pres(@460 V)
sure
6 Stud
dB(A)
IEC
75
63
60
60
75
63
60
65
75
63
65
65
75
63
65
68
75
80
67
65
68
80
67
68
68
80
67
68
67
82
67
68
67
82
70
68
67
82
70
68
67
84
72
68
71
84
72
72
74
84
75
75
74
85
75
75
74
87
78
75
74
87
78
77
75
89
79
80
77
89
79
80
77
89
80
80
77
91
83
82
77
91
83
82
77
91
85
82
77
91
85
82
89
89
M4
M4
M4
M4
M4
M4
M4
M6
M4
M4
M6
M6
M4
M4
M6
M6
M4
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M8
M6
M6
M8
M8
M6
M6
M8
M8
M8
M8
M8
M8
M8
M8
M10
M10
M8
M8
M10
M10
M8
M8
M10
M10
M8
M8
M10
M10
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
M16
GEA18201A X$D IEC_r11_GEA18201A X$D IEC 2/16/11 4:43 PM Page 6
Innovative
Technology
Complete
Product
Offering
The GE
Advantage
With GE, you have a single
point of responsibility for
all your motor needs. GE
offers a complete portfolio
of equipment from which to
choose, including:
• Motors from 1 to 100,000 HP
(0.75 to 75,000 kW)
• Generators up to 75 MVA
• Low and medium voltage
variable frequency drives
• Multiple product lines
covering all enclosures: WPI,
WPII, TEFC, TEAAC, TEWAC
Proven
Experience
World-Class
Service
GE has over 125 years of
experience in the electrical
industry with successful
global installations spanning
a wide variety of applications.
Very few competitors can
claim the depth and breadth
of experience that GE has
in creating and executing
solutions for its customers.
With GE’s wealth of global
experience comes a full
coverage offering for its
products along with leading
experts in the industries
they serve. Additionally,
GE experience and
innovation brings:
• Experienced sales force
• Engineering support
optimized for your
application
• Project management tools
• GE motors can adhere to
these industry standards
among others: NEMA, IEC,
CSA, API 541, 546, 547, and
661; IEEE 841, GOST, DIV 2,
Ex-n for Zone 2, Ex-p for
Zone 1 or 2, ATEX
GE is constantly innovating
product technologies to
meet and exceed customer
expectations. Founded by
world renowned inventors,
General Electric continues to
be a company made up of
individuals striving to design,
create, and build products
and solutions that improve
people’s lives. Among the
many tools used to produce
innovative products are:
• Electromagnetic finite
element analysis
• 3D solid modeling
• Virtual motor “building”
while in design phase
GE Energy
Fort Wayne, IN. 46802
800 541 7191
www.gemotors.com
For more information, please contact your GE sales representative
GE, ecomagination, X$D, GEGARD2400 are trademarks and a service mark of General Electric Company.
Copyright © 2011 General Electric Company. All rights reserved.
GEA18201A (2/2011)