Download American Standard 7143.803 User's Manual
Transcript
DOUBLE BOWL™ SINK SINGLE BOWL™ SINK ENAMELED STEEL DOUBLE BOWL KITCHEN SINK (shown) ❏ ❏ ❏ 7144.803 3-Hole 7144.804 4-Hole 7144.805 5-Hole Product Features: • Acid-resisting enameled steel • Double bowl design • Self-rimming installation • Available in 3, 4 or 5 faucet hole configurations • Silicone sealant supplied Nominal Dimensions: 838 x 559 x 184mm (33" x 22" x 7-1/4") Bowl sizes: 359mm (14-1/8") wide, 413mm (16-1/4") front to back, 178mm (7") deep Compliance Certifications Meets or Exceeds the Following Specifications: • ASME A112.19.4M for Enameled Steel Plumbing Fixtures To Be Specified SINGLE BOWL KITCHEN SINK ❏ ❏ ❏ Color: (specify White Heat,Bone, or Bisque) 7143.803 3-Hole ❏ Faucet*: (specify finish) 7143.804 4-Hole Product Features: • Acid-resisting enameled steel • Single bowl design • Self-rimming installation • Available in 3 or 4 faucet hole configurations • Silicone sealant supplied ❏ Basket Strainer: 4331.013 (Chrome only) ❏ Soap Dispenser*: 4503.115 (specify color) ❏ Trap: * See faucet section for additional models available Nominal Dimensions: 635 x 559 x 184mm (25" x 22" x 7-1/4") Bowl sizes: 552mm (21-3/4") wide, 413mm (16-1/4") front to back, 178mm (7") deep Compliance Certifications Meets or Exceeds the Following Specifications: • ASME A112.19.4M for Enameled Steel Plumbing Fixtures ROUGHING-IN DIMENSIONS SHOWN ON REVERSE SIDE OF PAGE KS-55 © 2003 American Standard Inc. Revised 8/02 DOUBLE BOWL™ SINK SINGLE BOWL™ SINK ENAMELED STEEL 7144.803/804/805 102mm (4) 102mm 102mm (4) 102mm (4) (4) 38mm (1-1/2) DIA. (TYP.) 7144.805 5 HOLE OPTIONAL 311mm (12-1/4) 7144.804 4 HOLE 89mm (3-1/2) 559mm (22) C/L 38mm R. (1-1/2) 397mm (15-5/8) 838mm (33) 13mm (1/2) FINISHED WALL OR SPLASH BACK 57mm (2-1/4) * CUTOUT NOTE 419mm (16-1/2) COUNTER TOP (BY OTHERS) 7143.803/804 102mm 171mm (6-3/4) (4) 914mm (36) SUGGESTED 152mm (6) 38mm (1-1/2) DIA. (TYP.) 102mm (4) 102mm (4) 7143.804 4 HOLE OPTIONAL COUNTERTOP FINISHED FLOOR CLAMPING DETAIL 311mm (12-1/4) LUG AND SCREW ASSEMBLY 89mm (3-1/2) 57mm (2-1/4) 559mm (22) NOTES: COUNTERTOP CUTOUT 800 x 521mm WITH 19mm RADIUS (31-1/2” x 20-1/2” WITH 3/4’ RADIUS) AT CORNERS. PROVIDE SUITABLE REINFORCEMENT FOR WALL AND COUNTERTOP SUPPORTS. STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. Important: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.4 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages. C/L 38mm R. (1-1/2) 318mm (12-1/2) 13mm (1/2) * CUTOUT NOTE 635mm (25) COUNTER TOP (BY OTHERS) 171mm (6-3/4) COUNTERTOP 21mm (13/16) MAX. CLAMPING DETAIL FINISHED WALL OR SPLASH BACK 1-1/2 O.D. TAILPIECE 21mm (13/16) MAX. 914mm (36) SUGGESTED 152mm (6) FINISHED FLOOR LUG AND SCREW ASSEMBLY 1-1/2 O.D. TAILPIECE NOTES: COUNTERTOP CUTOUT 597 x 521mm WITH 19mm RADIUS (23-1/2” x 20-1/2” WITH 3/4’ RADIUS) AT CORNERS. PROVIDE SUITABLE REINFORCEMENT FOR WALL AND COUNTERTOP SUPPORTS. STRAINERS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. Important: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.4 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages. KS-56 © 2003 American Standard Inc.