Download Alamo RX60 User's Manual

RX60 - RX72 - RX84
Rotary Mower
Rev 05-11
PART'S MANUAL
Part No. 00785503P
An Operator's Manual was shipped with the equipment in the Manual Canister.
This Operator's Manual is an integral part of the safe operation of this machine
and must be maintained with the unit at all times. READ, UNDERSTAND, and
FOLLOW the Safety and Operation Instructions contained in this manual before
operating the equipment. If the Operator's Manual is not with the equipment,
contact your dealer or Alamo Industrial (800-356-6286) to obtain a Free copy
before operating the equipment.
ALAMO INDUSTRIAL
1502 E. Walnut
Seguin, Texas 78155
210-372-3551
®
®
© 2011 Alamo Group Inc.
To the Owner/Operator/Dealer
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with
all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!!Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return
it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that
you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
BOLT TORQUE
Mounting procedures for mowers will require a significant amount of bolt nut and washer installation.
Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values
listed in the torque chart based on the bolt size and hardness.
Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry
values indicated in the chart.
Bolt tightness should be completed with and checked with a suitable torque wrench.
Torque checks should be completed throughout the life of the mower in accordance with the maintenance
chart provided in this manual.
Loose bolts on a frame or in a casting may be a result of:
●● Vibration from the mower due to imbalance of the mower blades
●● Pulled threads due to over tightening
●● Distortion of the hole due to under tightening during installation
Bolts broken or sheared in the mounting structure or tractor may be the result of:
●● Improper alignment of the Mounting Plate or Structure such that it is not sitting flat on the mating
surface
●● Distortion of the bolt due to over-tightening
●● Under tightening of the bolts
Check the bolt torque during installation and prior to delivery with a suitable torque wrench.
PARTS
SECTION
Parts Section – 1
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help locate
the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization ordering
the parts, who should be charged, and if possible, the serial number of the machine for which
the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a Purchase
Order.
6. The Manufacturer reserves the right to change prices without prior notice..
For maximum safety and to guarantee optimum product reliability, always use
genuine Alamo Industrial Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:
ALAMO INDUSTRIAL
1502 E. Walnut
Seguin, Texas 78155
830-379-1480
©2011 Alamo Group Inc.
®
®
Parts Section – 2
PART NAME INDEX
A-FRAME QUICK HITCH ASSEMBLY - RX60, RX72............................................................................................................................. 4
A-FRAME QUICK HITCH ASSEMBLY - RX84........................................................................................................................................ 5
A-FRAME QUICK HITCH ATTACHMENT - RX60, RX72...................................................................................................................... 6
A-FRAME QUICK HITCH ATTACHMENT - RX84.................................................................................................................................. 7
AXLE ASSEMBLY PULL TYPE - RX84.................................................................................................................................................... 8
BLADE PAN ASSEMBLY - RX60............................................................................................................................................................. 10
BLADE PAN ASSEMBLY - RX72............................................................................................................................................................. 11
BLADE PAN ASSEMBLY - RX84............................................................................................................................................................. 12
CASTER WHEEL AND HUB ASSEMBLY.............................................................................................................................................. 13
CHAINGUARD ASSEMBLY - DOUBLE FRONT RX84......................................................................................................................... 14
CHAINGUARD ASSEMBLY - DOUBLE REAR RX84........................................................................................................................... 15
CHAINGUARD ASSEMBLY - FRONT.................................................................................................................................................... 16
CHAINGUARD ASSEMBLY - REAR....................................................................................................................................................... 17
DEFLECTOR ASSEMBLY - FRONT........................................................................................................................................................ 18
DEFLECTOR ASSEMBLY - REAR........................................................................................................................................................... 19
DRIVELINE ASSEMBLY CV.................................................................................................................................................................... 20
DRIVELINE ASSEMBLY LIFT - RX60, RX72, RX84............................................................................................................................. 21
DRIVELINE ASSEMBLY LIFT CAT-5 - RX84........................................................................................................................................ 22
DRIVELINE JACKSHAFT ASSEMBLY - RX84...................................................................................................................................... 23
GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11616 - BELOW...................................................................................................... 24
GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11617 - CURRENT.................................................................................................. 26
GEARBOX ASSEMBLY - RX84 - SERIAL 10022 - BELOW.................................................................................................................. 28
GEARBOX ASSEMBLY - RX84 - SERIAL 10023 - CURRENT............................................................................................................ 30
GEARBOX ATTACHMENT RX60, RX72 SERIAL 11616-BELOW, & RX84....................................................................................... 32
GEARBOX ATTACHMENT RX72 SERIAL# 11617-CURRENT............................................................................................................ 33
HYDRAULIC CYLINDER......................................................................................................................................................................... 34
SKID SHOE ASSEMBLY........................................................................................................................................................................... 35
SLIP CLUTCH ASSEMBLY - RX60, RX72, RX84................................................................................................................................... 36
SLIP CLUTCH ASSEMBLY CAT-5 - RX84............................................................................................................................................. 37
TAILWHEEL ASSEMBLY - DUAL RX84................................................................................................................................................ 38
TAILWHEEL ASSEMBLY - RX60, RX72................................................................................................................................................ 39
TAILWHEEL ASSEMBLY - RX84............................................................................................................................................................ 40
TAILWHEEL HUB ASSEMBLY............................................................................................................................................................... 41
TONGUE ASSEMBLY - RX84.................................................................................................................................................................. 42
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -3
A-FRAME QUICK HITCH ASSEMBLY - RX60, RX72
ITEM
PART NO. QTY.
DESCRIPTION
1
00780585
-
FLAT,REAR BRACE - RX72
00781038
-
FLAT,REAR BRACE - RX60
00780582
-
FLAT, A-FRAME - RX72
00780563
-
FLAT, A-FRAME, QUICK HITCH - RX60
00780549
-
BAR, BRACE - RX72
00780603
-
BAR, BRACE - RX60
4
00009500
-
BOLT-HEX 3/4 NC 4-1/2 PL5
5
0758550030
-
SPACER
6
00037200
-
NUT TOPLOCK 3/4 NC PLC
7
2101120
-
CARB 5/8 NC X 2-1/2 PL5 - RX72
4905
-
CARB 5/8-11 NC 2 PL5 - RX60
0732020020
-
BUSHING - RX72
523012
-
BUSHING, ORDER 780 MIN HT - RX60
9
00756077
-
WASHER,5/8 HARDENED
10
00695100
-
NUT,TOPLOCK 5/8 NC PLB
11
02845600
-
HEXB 5/8 NC 3 PL5 - RX72
00703200
-
HHCS 5/8 NC 2 3/4 PL5 - RX60
12
00780592
-
BUSHING, A-FRAME TOGGLE
13
02845500
-
HEXB 5/8 NC 2 PL5
2
3
8
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -4
A-FRAME QUICK HITCH ASSEMBLY - RX84
ITEM
PART NO. QTY.
DESCRIPTION
1
00781069
2
FLAT, REAR BRACE
2
00781411
1
FLAT, A-FRAME LH
3
00781410
1
FLAT, A-FRAME RH
4
00781117
2
FLAT, QUICK HITCH TOGGLE
5
0758550031
1
BUSHING
6
00761199
2
SPACER TUBE
7
0732020020
4
BUSHING
8
00756077
10
5/8 HARDENED WASHER
9
00695100
13
NUT,5/8 NC TOPLOCKNUT
10
02845500
1
BOLT, 5/8 X 2
11
00600700
2
HEXB 5/8 NC 3-1/4 PL5
12
02030300
1
NUT, 1" TOPLOCK
13
00750479
1
HEXB 1NC 4-3/4 PL5
14
2101120
2
CARB 5/8 X 2-1/2
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -5
A-FRAME QUICK HITCH ATTACHMENT - RX60, RX72
ITEM
PART NO. QTY.
DESCRIPTION
1
00775243
2
PIN WRIST CAT 1&2
2
2196
2
CLIP (LYNCH PIN), 13/32 DIA.
3
00780663
1
FLAT, DRIVELINE STORAGE
4
00001800
1
LOCKNUT TLM 1/2 NC PLB
5
00748823
1
HHCS 1/2-13UNC 1-1/2 PL5
6
02845500
4
HEXB 5/8 NC 2 PL5 - RX72
00695100
4
LOCKNUT TOPLOCK 5/8NC PLB - RX60
7
00756077
4
WASHER,5/8 HARDENED
8
00761724
2
BUSHING HITCH
9
0732020020
2
BUSHING - RX72
523012
2
BUSHING, ORDER 780 MIN HT - RX60
10
00695100
2
NUT,TOPLOCK 5/8 NC PLB
11
00785238
2
BUSHING,CAT. II QUICK HITCH
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -6
A-FRAME QUICK HITCH ATTACHMENT - RX84
ITEM
PART NO. QTY.
DESCRIPTION
1
69141
2
PIN, HITCH CAT II & III
2
2196
2
CLIP (LYNCH PIN), 13/32 DIA.
3
00780663
1
FLAT, DRIVELINE STORAGE
4
00001800
1
LOCKNUT TLM 1/2 NC PLB
5
00749130
1
HHCS 1/2-13UNC 1-3/4 PL5
6
00002700
2
FLATWASHER 1/2 PL STD
7
00750952
2
HEXB,5/8NC X 2-1/2,ZP,GRD5
8
0732020020
2
BUSHING
9
00756077
2
WASHER,5/8 HARDENED
10
00695100
2
LOCKNUT TOPLOCK 5/8NC PLB
11
00037100
2
HEXB 3/4 NC 2-1/2 PL5
12
511016
2
BUSHING YDP
13
5312316
2
WASHER, 3/4
14
00037200
2
NUT 3/4-NC TOPLOCK GRC PL
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -7
AXLE ASSEMBLY PULL TYPE - RX84
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -8
AXLE ASSEMBLY PULL TYPE - RX84
Continued...
ITEM
PART NO. QTY.
DESCRIPTION
1
00781149
1
WDMT, AXLE - 284
2
00781178
1
ASY, LEVEL ROD - 284
3
651102
2
PIN, DRILLED
4
00002701
2
FLATWASHER, 3/4, TYPE AW, ZP
5
00755153
2
PIN, COTTER 3/16 X 1-1/2 PLATED
6
00001800
2
LOCKNUT TLM 1/2 NC PLB
7
00764375
2
HHCS 1/2NC X 3-1/4 PL5
8
00007800
2
HEXB 3/4 NC 3 PL5
9
511016
4
BUSHING
10
00775616A
2
ASY,HUB & SPINDLE
11
00037200
2
NUT 3/4-NC TOPLOCK GRC PL
12
00748823
2
HHCS, 1/2 - 13NC X 1-1/2 PL5
13
02959924
2
NUT, 1/4" NC
14
03200347
1
EMBLEM, SMV
15
00024100
4
1/4" FLATWASHER
16
10058000
2
HHCS 1/4 NC 1 PL5
17
8727A
1
HYDRAULIC CYLINDER
18
103266
1
CYLINDER PIN
19
02822500
2
FLATWASHER 1 PL STD
20
00606000
4
PIN, COTTER 3/16 X 2
21
7329
1
ADAPTER, HYD, STGHT
22
0652141311
1
STRAIGHT ADAPTER 8MP-8MJ
23
8354
1
PIN, HYD. CYLINDER
24
00785646
1
SMV BRACKET
25
00777963
1
TRANSPORT LOCK PLATE
26
00758643
1
ROD, CONTROL
27
00781177
1
WELDMENT LONG LEVEL ROD
28
00778159
1
NUT, 9" ADJUSTING
29
5C1490
1
HEXNUT, 7/8 JAM ZP
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -9
BLADE PAN ASSEMBLY - RX60
ITEM
PART NO. QTY.
DESCRIPTION
1
00781388
1
WDMT,BLADE PAN (SERIAL# RX60-10042 AND BELOW)
00786797
1
WDMT,BLADE PAN (SERIAL# RX60-10043 TO CURRENT)
00780882
2
BLADE, CCW FAN 22-1/2 CTR-TIP 260
0652010030
2
BLADE, FLAT
00757830
2
BLADE, HIGH SUCTION TWISTED
3
00780945
2
WASHER 1-5/64 SQ HOLE X 3 OD 260
4
5GL16140
2
LOCKNUT 1 -14 LH TLN PL - 260
5
571044
2
BOLT SHOULDER - 260
6
571045
2
WASHER - HARDENED - 260
2
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -10
BLADE PAN ASSEMBLY - RX72
ITEM
PART NO. QTY.
DESCRIPTION
1
00780622
1
WLDMT, BLADE PAN 272 (SERIAL# 11616-BELOW)
2
00786485
1
WLDMT, BLADE PAN 272 (SERIAL# 11617-CURRENT)
3
5GL16140
4
LOCKNUT 1 -14 LH TLN PL
4
571045
4
WASHER, HARDENED
5
571044
4
BOLT SHOULDER
6
00757830
2
BLADE, HIGH SUCTION TWISTED
0652010030
2
BLADE, FLAT
00780882
2
BLADE, CCW FAN 22-1/2 CTR-TIP 260 & 272
7
00780945
4
WASHER 1-5/64 SQ HOLE X 3 OD
8
00779283
4
WASHER, HARDENED BLADE WEAR
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -11
BLADE PAN ASSEMBLY - RX84
ITEM
PART NO. QTY.
DESCRIPTION
1
00786649
1
WELDMENT, BLADE CARRIER
2
5GL16140
2
LOCKNUT
3
571045
2
WASHER 1 STRUCURAL
4
571044
2
BOLT, SHOULDER BLADE
5
00778047
2
BLADE WASHER
6
0582010330
2
BLADE, CCW FAN ROTARY MOWER
582013A
2
BLADE, FLAT
00757833
2
BLADE, HIGH SUCTION TWISTED
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -12
CASTER WHEEL AND HUB ASSEMBLY
ITEM
PART NO. QTY.
DESCRIPTION
00776220
1
CASTER WHEEL AND HUB ASSEMBLY
1
373024H
1
TIRE WHEEL ASSEMBLY
2
00780238
1
TAILWHEEL HUB ASSEMBLY INCLUDES ALL ITEMS EXCEPT 1, 13, 21, & 18
4
00776214
1
HUB
5
00776213
2
BEARING CONE & CUP
6
00776219
2
OIL SEAL
7
00772082
1
GREASE FITTING (THREADED)
8
00776216
4
BOLT
9
7A6166
4
BOLT
10
00776215
4
FLATWASHER
11
00012101
4
LOCKWASHER
12
00013901
4
NUT
13
0585020210A
1
CASTER FORK WELDMENT
14
00772017
2
BUSHING
15
00772018
2
DUST CAP
16
00776211
1
SPINDLE BOLT
17
02822500
1
WASHER
18
15B2400
1
FLATWASHER
19
00776212
1
CASTELLATED NUT
20
00771620
1
COTTER PIN
21
00758899
1
COTTER PIN
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -13
CHAINGUARD ASSEMBLY - DOUBLE FRONT RX84
ITEM
PART NO. QTY.
DESCRIPTION
1
00785248
1
ASY,FRONT DOUBLE CG-RX84
2
00748823
7
HHCS 1/2-13UNC 1-1/2 PL5
3
00002700
7
FLATWASHER 1/2 PL STD
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -14
CHAINGUARD ASSEMBLY - DOUBLE REAR RX84
ITEM
PART NO. QTY.
DESCRIPTION
1
00785249
1
ASY,REAR DOUBLE CG-RX84
2
00748823
9
HHCS 1/2-13UNC 1-1/2 PL5
3
00002700
18
FLATWASHER 1/2 PL STD
4
00001800
9
LOCKNUT TLM 1/2 NC PLB
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -15
CHAINGUARD ASSEMBLY - FRONT
ITEM
PART NO. QTY.
DESCRIPTION
1
00781209
1
FLAT, FRONT C.G. BRACKET - RX72
00781249
1
FLAT, FRONT C.G. BRACKET - RX60
00781265
1
FLAT, FRONT C.G. BRACKET - RX84
00002700
5
FLATWASHER 1/2 PL STD - RX60 RX72
00002700
7
FLATWASHER 1/2 PL STD RX84
00748823
5
HHCS 1/2-13UNC 1-1/2 PL5 - RX60 RX72
00748823
7
HHCS 1/2-13UNC 1-1/2 PL5 - RX84
2
3
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -16
CHAINGUARD ASSEMBLY - REAR
ITEM
PART NO. QTY.
DESCRIPTION
1
00785229
1
BRACKET,REAR CHAIN GUARD - RX72
00785230
1
ASY,REAR CHAIN GUARD - RX60
00781264
1
BRACKET,REAR CHAIN GUARD - RX84
00748823
9
HHCS 1/2-13UNC 1-1/2 PL5 - RX84 RX72
00748823
7
HHCS 1/2-13UNC 1-1/2 PL5 - RX60
00002700
18
FLATWASHER 1/2 PL STD - RX84 RX72
00002700
14
FLATWASHER 1/2 PL STD - RX60
00001800
9
LOCKNUT TLM 1/2 NC PLB - RX84 RX72
00001800
7
LOCKNUT TLM 1/2 NC PLB - RX60
2
3
4
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -17
DEFLECTOR ASSEMBLY - FRONT
ITEM
PART NO. QTY.
DESCRIPTION
1
00780879
1
PANEL, FRONT RUBBER DEFLECTOR - RX72
00781039
1
PANEL, FRONT RUBBER DEFLECTOR - RX60
00781119
1
PANEL, FRONT DEFLECTOR - RX84
00780881
1
FLAT, DEFLECTOR STRAP - RX72
00781041
1
FLAT, DELFECTOR STRAP - RX60
00781144
1
FLAT, FRONT DEFLECTOR STRAP - RX84
00748823
5
HHCS 1/2-13UNC 1-1/2 PL5 - RX60 RX72
00748823
7
HHCS 1/2-13UNC 1-1/2 PL5 - RX84
00002700
5
FLATWASHER 1/2 PL STD - RX60 RX72
00002700
7
FLATWASHER 1/2 PL STD - RX84
2
3
4
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -18
DEFLECTOR ASSEMBLY - REAR
ITEM
PART NO. QTY.
DESCRIPTION
1
00781231
1
PANEL, REAR RUBBER DEFLECTOR - RX72
00781229
1
PANEL, REAR RUBBER DEFLECTOR - RX60
00781079
1
PANEL, REAR DEFLECTOR - RX84
00781232
1
FLAT, REAR DEFLECTOR STRAP - RX72
00781230
1
FLAT, REAR DEFLECTOR STRAP - RX60
00781131
1
FLAT, REAR DEFLECTOR STRAP - RX84
00748823
9
HHCS 1/2-13UNC 1-1/2 PL5 - RX72 RX84
00748823
7
HHCS 1/2-13UNC 1-1/2 PL5 - RX60
00002700
18
FLATWASHER 1/2 PL STD - RX72 RX84
00002700
14
FLATWASHER 1/2 PL STD - RX60
00001800
9
LOCKNUT TLM 1/2 NC PLB - RX72 RX84
00001800
7
LOCKNUT TLM 1/2 NC PLB - RX60
2
3
4
5
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -19
DRIVELINE ASSEMBLY CV
ITEM
PART NO. QTY.
DESCRIPTION
00779504
1
DRIVELINE ASSEMLBY CV
1
2716820
1
REPAIR KIT
2
00779522
1
ASY,SAFETY SLIDE LOCK YOKE
3
00779521
2
KIT,CROSS & BEARING
4
00779520
1
HOUSING,CENTER
6
00779051
1
GUARD REPAIR KIT (NOT SHOWN)
11
00780376
1
NYLON BEARING & KEEPER
13
00779519
1
KIT,CROSS & BEARING
14
00779518
1
YOKE
15
02956948
1
LOCKNUT 5/8 NC PLC
16
00765690
1
HHCS 5/8-11UNC 3LG GR8 PL
00779523
1
ASY,JOINT & TUBE 1/2 W/GUARD
00779524
1
ASY,JOINT & SHAFT 1/2 W/GUARD
00779525
1
ASY,GUARD SET
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -20
DRIVELINE ASSEMBLY LIFT - RX60, RX72, RX84
ITEM
PART NO. QTY.
DESCRIPTION
00781390
1
DRIVELINE CAT4 1-3/4-20 SPLINE
1
00779516
1
YOKE 1 3/8" -6SPL
2
00779517
2
CROSS & BEARING KIT
3
00756934
2
PIN,ROLL 10 X 80
4
8982
1
YOKE INBOARD
7
8387
1
INBOARD YOKE
8
00779512
1
FRICTION CLUTCH
12
8393
2
BEARING RING
14
00759217
2
SCREW 1/2 LG #8 PAN
15
00756005
1
DECAL-ROTATING DRIVELINE
16
00756004
1
DECAL-SHIELD MISSING
17
8974
1
SUPPORT BEARING
18
1416601
1
ZERK
00779533
1
SHIELD KIT INCLUDES ITEMS 10, 11, 12, 14 & 15
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -21
DRIVELINE ASSEMBLY LIFT CAT-5 - RX84
ITEM
PART NO. QTY.
DESCRIPTION
00781406
1
ASY,DRIVELINE W/CLUTCH,540RPM
1
W821A
1
YOKE 44 1-3/8-6 SLID
2
W840
2
KIT,CROSS SAME AS P
3
W816F
1
YOKE SHAFT PAINT BLA
4
00775344
1
YOKE, I.B. TUBE & SLEEVE W.A.
5
00779357
1
COMPT. CLUTCH HUB 1440 1350MM
6
00775345
1
OUTER SHIELD TUBE ASSY
7
00775346
1
INNER SHIELD TUBE ASSY
8
00775347
1
SHIELD BEARING
9
00775348
4
SUPPORT BEARING
10
00752670
2
FITTING,GREASE STRAIGHT 1/4-28
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -22
DRIVELINE JACKSHAFT ASSEMBLY - RX84
ITEM
PART NO. QTY.
DESCRIPTION
00785491
1
JACKSHAFT
1
00779517
1
CROSS & BEARING KIT
2
00756934
1
SPRING PIN 10 X 80
3
8982
1
INBOARD YOKE 1B
4
8393
2
BEARING RING SC25
5
00759217
2
SCREW- IN ITEM 7 & 8
6
00756005
1
DECAL OUT. -IN ITEM 9
7
00756004
1
DECAL INN. -IN ITEM 1
00774208
1
CC LOCK ASSY - IN ITEM 6
00779512
1
CLUTCH
8
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -23
GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11616 - BELOW
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -24
GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11616 - BELOW
Continued...
ITEM
PART NO. QTY.
DESCRIPTION
00780880P
1
ASY,GEARBOX, SUPER 75 1:1.6 SU
1
00781380
1
HOUSING 75 SERIES E.O.
2
00755954
8
LOCKWASHER M10
3
00758659
8
HEXB METRIC 10-P1.5 - 32MM PL5
4
00758664
1
CAP,INPUT IEG 20-001
5
00758689
1
SHAFT,INPUT
6
00758653
1
SEAL 1-3/4IDX2.378OD
7
00758667
1
SHIM .012 2.44 O.D.
8
00758668
1
SHIM,0.020 2.44 O.D.
9
00758646
1
SHIM, ADJUSTMENT - .004"
10
00758647
1
SHIM, ADJUSTMENT - .010"
11
00759977
1
SPACER GEAR MOUNT I
12
00781381
1
OUTPUT SPACER
13
00758663
1
CAP,OUTPUT IEG #20-002
14
00758672
4
LOCKWASHER,M12 IEG 07-002
15
02959661
4
HEXB, M12-P1.75 X 35MM PL8.8
17
00606000
1
PIN,COTTER 3/16X2
18
00758692
1
NUT SLOTTED HEX FLG 1-14UNS PL
19
00758674
1
SEAL,OUTPUT SHAFT 50
20
00758676
1
GASKET, .004 OR .1M
21
00758677
1
GASKET, .010 OR .25
22
00781382
1
OUTPUT SHAFT
23
00769938
2
BEARING #30210
24
00758698
1
GEAR,15 TOOTH
25
00762121
1
NUT,HEX THIN SLOTTED
26
00026200
1
PIN,COTTER 5/32 X 1-1/2
27
00755615
2
BEARING
28
00770737
2
LEVEL PLUG M18 X 1.5
29
00769321
3
WASHER,SEALING,17.8M
30
00758657
1
SPACER,INPUT SHAFT
31
00758701
1
GEAR,24 TOOTH
32
00778907
1
ASY,DIP STICK
33
00762114
1
PLUG,VENT W/WASHER 18M-P1.5
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -25
GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11617 - CURRENT
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -26
GEARBOX ASSEMBLY - RX60, RX72 - SERIAL 11617 - CURRENT
Continued...
ITEM
PART NO. QTY.
DESCRIPTION
00785788
1
ASY,GEARBOX - NON-LUBED - GEAR IN FRONT 540 RPM,1:1.50 RATIO,1-3/4-20 SPLINE
1
00786292
1
KIT,ROLLER BEARING
2
00786293
1
KIT,GEAR SET
3
00786294
1
KIT,SEAL & SHIM
5
00758484
1
DIPSTICK VENT PLUG 1/2" - FILL
7
00786287
1
SHAFT,INPUT - 1-3/4-20 SPL.
9
00786305
1
COVER,GEAR BOX
10
00755633
1
PLUG,SOLID GAS - 3/8"
11
00754764
4
HEXB M10 X 1.25 X 20 PL.8.8
17
00786288
1
SHAFT,OUTPUT
18
00755621
1
NUT,CASTLE - M30 X 1.5
19
70499
1
PIN,COTTER - B5 X 60
21
00755624
1
NUT,CASTLE - M30 X 2.0
25
00755623
1
WASHER,BOLT - 31 X 56 X 6
26
2716423
1
PIN,COTTER B6 X 60
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -27
GEARBOX ASSEMBLY - RX84 - SERIAL 10022 - BELOW
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -28
GEARBOX ASSEMBLY - RX84 - SERIAL 10022 - BELOW
Continued...
ITEM
PART NO. QTY.
DESCRIPTION
00781080P
1
GEARBOX ASSEMBLY
1
00781380
1
HOUSING 75 SERIES E.O.
2
00755954
1
LOCKWASHER M10 SPRING
3
00758859
8
M10 X 1.5 X 30 HEX HEAD SCREW
4
00758664
1
CAP, INPUT IEG 20-001
5
00758689
1
SHAFT, INPUT
6
00758653
1
SEAL 1-3/4ID X 2.378OD
7
00758667
1
SHIM .012 2.44 O.D.
8
00758668
1
SHIM,0.020 2.44 O.D.
9
00758646
1
SHIM, ADJUSTMENT - .004
10
00758647
1
SHIM, ADJUSTMENT - .010
11
00759977
1
SPACER GEAR MOUNT I
12
00781381
1
OUTPUT SPACER
13
00758663
1
CAP,OUTPUT IEG #20-002
14
00758672
4
LOCKWASHER, M12 IEG 07-002
15
02959661
4
HEXB, M12-P1.75 X 35 MM PL8.8
17
00606000
1
COTTER PIN 3/16" X 2"
18
00758692
1
NUT SLOTTED HEX FLG 1-14 UNS PL
19
00758674
1
OUTPUT OIL SEAL
20
00758676
1
GASKET, .004 OR .1M
21
00758677
1
GASKET, .010 OR .25
22
00781382
1
OUTPUT SHAFT
23
00769938
1
BEARING #30210
24
00781088
1
GEAR, 16 TOOTH PINION
25
00762121
1
NUT, HEX, THIN SLOTTED
26
00026200
1
PIN,COTTER 5/32 X 1-1/2
27
00755615
1
BEARING #30209
28
00770737
1
LEVEL PLUG M 18 X 1.5
29
00769321
1
WASHER, SEALING
30
00758657
1
SPACER, INPUT SHAFT
31
00781089
1
GEAR, 22 TOOTH
32
00778907
1
ASSY-DIPSTICK FOR SUPER 75 GBS
33
00762114
1
PLUG,VENT, 18M-P1.5 5PSI
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -29
GEARBOX ASSEMBLY - RX84 - SERIAL 10023 - CURRENT
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -30
GEARBOX ASSEMBLY - RX84 - SERIAL 10023 - CURRENT
Continued...
ITEM
PART NO. QTY.
DESCRIPTION
00785790
1
ASY, GEARBOX
1
00786296
1
GEAR,CROWN Z22 M6
2
00755615
2
BEARING,ROLLER - 30209
3
00755619
2
SHIM KIT - 70.3MM X 84.7MM
4
00755618
2
SNAP RING - 85MM X 88.5MM X 3MM
5
00755634
1
CAP,OIL - 85MM X 10MM
6
00786287
1
SHAFT,INPUT - 1-3/4-20 SPL.
7
00786291
1
SEAL,OIL - 45MM X 85MM X 10MM
8
00786305
1
COVER,GEAR BOX
9
00755633
1
PLUG,SOLID GAS - 3/8"
10
00754764
4
HEXB M10 X 1.25 X 20 PL.8.8
11
00786297
1
GEAR,PINION Z18 M6
12
2516460
1
SNAP RING - 50MM X 47MM X 3MM
13
00755632
1
SHIM KIT - 45.3MM X 65.3MM X 2.5MM
14
00769938
2
BEARING,ROLLER - 30210
15
00755622
1
SHIM KIT - 50.3MM X 70.3MM
16
00786295
1
SHAFT,OUTPUT
17
00756943
1
NUT,CASTLE - M40 X 1.5
18
70499
1
PIN,COTTER - B5 X 60
19
00786298
1
SHIM KIT - 40.3MM X 61.7MM X 1.0MM
20
00755624
1
NUT,CASTLE - M30 X 2.0
21
00755627
1
SEAL,OIL - 50MM X 90MM X 10MM
22
00755626
1
WASHER,PROTECTIVE
23
00755623
1
WASHER,BOLT - 31 X 56 X 6
24
00754336
1
1/2" GAS SOLID PLUG
25
2716423
1
PIN,COTTER B6 X 60
26
00786292
1
KIT,ROLLER BEARING
27
00786299
1
KIT,GEAR SET
28
00786294
1
KIT,SEAL & SHIM
29
00758484
1
DIPSTICK VENT PLUG 1/2" - FILL
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -31
GEARBOX ATTACHMENT RX60, RX72 SERIAL 11616-BELOW, & RX84
ITEM
PART NO. QTY.
DESCRIPTION
1
00775571
1
WLDMT SHIELD
2
00775573
1
WLDMT BRKT SHIELD
3
00778907
1
ASSY-DIPSTICK FOR SUPER 75 GBS
4
00762114
1
PLUG,VENT W/WASHER 18M-P1.5
5
02845500
6
HEXB 5/8 NC 2 PL5
6
00695100
6
LOCKNUT TOPLOCK 5/8NC PLB
7
00756077
6
WASHER,5/8 HARDENED
8
00002700
1
FLATWASHER 1/2 PL STD
9
00002000
3
HEX CAP 3/8-16 X 3/4 GR.5 ZP
10
00012101
3
LOCKWASHER 3/8 PL
11
00011100
3
FLATWASHER STD 3/8
12
5F8130
1
1/2 NC WING NUT
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -32
GEARBOX ATTACHMENT RX72 SERIAL# 11617-CURRENT
ITEM
PART NO. QTY.
DESCRIPTION
1
00785575
1
GEARBOX SCHIELD, 4-1/8"-5" BC
2
00785574
1
RING,GB SHIELD INNER SUPPORT
3
00023500
4
FLATWASHER, 5/16" TYPE AW, ZP
4
02958784
4
BOLT METRIC 8-P1.25-20MM PL8.8
5
00037200
6
LOCKNUT, 3/4"-NC TLM PL C
6
5312316
6
WASHER, 3/4" HARDENED
7
00037100
6
HEXB 3/4" NC 2-1/2" PL5
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -33
HYDRAULIC CYLINDER
ITEM
PART NO. QTY.
DESCRIPTION
8727A
1
HYDRAULIC CYLINDER
1
00774729
1
CLEVIS CAP 2.5-3/4 ORB-1.00
2
00774734
1
ROD CAP 2.50-1.25-3/4 ORB
3
00774730
1
PISTON 2.5-0.75-S HALL W/RING
4
00774753
1
ROD CYL 1.25-08-0.75-1.25-A
5
3047111
1
CYLINDER TUBE
6
3047112
4
TIE ROD
9
00774760
1
SEAL KIT
15
3047117
1
THREAD LOCK
16
1917140
1
ROD CLEVIS
17
00774740
1
SC SCKT SET 3/8UNCX1/2 KNUR
18
33003H5C
8
HEX NUT 3/8-16 GR.5
19
5JRC12160
1
NUT TOPLOCK 3/4 NF PLC
20
1917132
1
SCKT HD O-RNG PLUG,3/4-16 UNF
21
2417154
1
BREATHER,CYLINDER #8 ORB
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -34
SKID SHOE ASSEMBLY
ITEM
PART NO. QTY.
DESCRIPTION
1
00778905
2
SKID SHOE BAR
2
8277
6
PLOW BOLT 3/8 NC 1-1/4 #3 PL
3
4528
6
NUT, LOCK 3/8-16 FLG WHIZ
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -35
SLIP CLUTCH ASSEMBLY - RX60, RX72, RX84
ITEM
PART NO. QTY.
DESCRIPTION
00779512
1
SLIP CLUTCH ASSEMBLY
1
00779511
1
FLANGE YOKE
2
00754202
2
RING,CLUTCH LINING
3
00775322
1
HUB 1 3/4-20 I.C.
4
00775323
1
PLATE, THRUST
5
00775324
1
SPRING, BELLEVILLE
6
61064C8
6
M10X1.5X50 GR.8.8 HEX CAPSCREW
7
00765961
6
NUT MET TLE 10MM-P1.5 PL
8
00772648
2
NUT,HEX TOP LOCK-M12 X 1.75
9
61076C8
2
M12X1.75X65 GR.8.8 HEX CAPSCRE
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -36
SLIP CLUTCH ASSEMBLY CAT-5 - RX84
ITEM
PART NO. QTY.
DESCRIPTION
1
00775383
1
YOKE FLANGE
2
0921000462
4
DISK, CLUTCH 5-15/16X3-19/32X
3
00779366
1
HUB 1-3/4-20
4
00775335
1
DRIVE PLATE
5
00779365
1
DRIVE PLATE
6
00775337
1
THRUST PLATE
7
00775338
6
BOLT HEX M12 X P1.25 X 115M
8
00775339
6
COMPRESSION SPRING
9
00754566
6
LOCKWASHER, 12MM
10
00756164
6
NUT METRIC 12MM-P1.75 GR.8.8
11
00774208
1
LOCK ASY CC YOKE
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -37
TAILWHEEL ASSEMBLY - DUAL RX84
ITEM
PART NO. QTY.
DESCRIPTION
1
00781077
2
WDMT, T/W BEAM - 284/484
2
00781071
2
FLAT, POSITION BRACKET
3
00785473
2
MOUNT, DUAL TAILWHEEL BEAM
4
00007800
2
HEXB 3/4 NC 3 PL5
5
00037200
2
LOCKNUT 3/4-NC TLM PLC
6
00749130
8
HHCS 1/2-13 UNC 1-3/4 PL5
7
00001800
8
LOCKNUT TLM 1/2 NC PLB
8
00776220
1
WHEEL & FORK ASSEMBLY
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -38
TAILWHEEL ASSEMBLY - RX60, RX72
ITEM
PART NO. QTY.
DESCRIPTION
1
00780876
1
WDMT, T/W BEAM - 272
00781036
1
WDMT, T/W BEAM - 260
2
0585020300
1
BRACKET, POSITION
3
00785239
1
MOUNT, TAILWHEEL BEAM
4
00059000
1
HEXB 5/8 NC X 5 PL5
5
00695100
1
LOCKNUT TOPLOCK 5/8NC PLB
6
00748823
4
HHCS 1/2-13 UNC 1-1/2 PL5
7
00001800
4
LOCKNUT TLM 1/2 NC PLB
8
00776220
1
ASSY CASTER FORK & WHEEL
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -39
TAILWHEEL ASSEMBLY - RX84
ITEM
PART NO. QTY.
DESCRIPTION
1
00781077
1
WELDMENT, T/W BEAM
2
0585020300
1
BRACKET POSITION
3
00785473
1
MOUNT, T/W BEAM
4
00007800
1
HEXB 3/4 NC3 PL5
5
00781367
1
TUBE BUSHING
6
00037200
1
LOCKNUT 3/4 NC TLM PLC
7
00749130
4
HHCS 1/2-13UNC 1-3/4 PL5
8
00001800
4
TOPLOCKNUT, 1/2-13 NC PL
9
15B2400
4
FLATWASHER NAR 1-1/2 PL
10
00758899
1
PIN COTTER 3/8X2-1/2 PL EXTEND
11
00776220
1
ASY,CASTER FORK & WHEEL
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -40
TAILWHEEL HUB ASSEMBLY
ITEM
PART NO. QTY.
DESCRIPTION
00780238
1
ASSY, TAILWHEEL HUB
1
00776214
1
HUB 4 BOLT
2
00776213
2
BEARING
3
00759635
4
FLATWASHER 1/2 HARDND NONPLATD
4
00762462
4
HEXB METRIC 12-P1.75- 25MM PL5
5
00772017
2
BUSHING SPINDLE STEP
6
00772018
2
DUST CAP
7
00776219
2
SEAL OIL 40 X 62 X 8
8
00776211
1
BOLT SPINDLE M24 X 2 X 186
9
00776217
2
WASHER FLAT 026 X 044 X 4 FLAT
10
00776212
1
NUT SPINDLE M24 X 2
11
00772082
1
NIPPLE, GREASE M8X1
12
00771620
1
PIN,COTTER 5/32X2-1/2 PL
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -41
TONGUE ASSEMBLY - RX84
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -42
TONGUE ASSEMBLY - RX84
Continued...
ITEM
PART NO. QTY.
DESCRIPTION
1
00777459
1
WDMT, TONGUE
2
00778053
1
WDMT, CLEVIS
3
00760941
1
WDMT, JACK TUBE MOUNT
4
00764515
1
CHAIN, SAFETY TOW-6000# CAP.
5
1431565
1
SHAFT, PTO IID TRANSPORT SUPPRT
6
40010000
1
PIN, COTTER 1/8 X1
7
00755076
1
HHCS 1 NC 5-1/2 PL8
8
00759275
3
WASHER, HITCH CLEVIS
9
02030300
3
NUT TOPLOCK 1 NC PLB
10
00754107
2
BOLT 1 - 8UNC X 6-1/2 PL8
11
00756077
2
WASHER, 5/8 HARDENED
12
00695100
2
LOCKNUT TOPLOCK 5/8 NC PLB
13
00761890
2
BUSHING 1.5 OD X 1.14 IDX 1-3/16 LG
14
00758146
2
PIN, TONGUE PIVOT
15
2196
2
CLIP (LYNCH PIN), 13/32 DIA.
16
00772391
1
PARKING JACK SIDEWIND
17
00695100
4
NUT, 5/8 NC TOPLOCK
18
00001400
8
FLATWASHER 5/8 PL STD
19
00775006A
1
BEARING ASSEMBLY
20
00002701
2
FLATWASHER, 3/4, TYPE AW, ZP
21
00037200
1
LOCKNUT 3/4-NC TLM PLC
22
00002700
1
FLATWASHER 1/2
23
5F8130
1
WINGNUT 1/2 NC
24
00781172
1
HHCS 3/4 NC 8-1/2 PL5
25
02845800
4
HEXB, 5/8 NC X 4-1/2 GRD5 ZP
26
00749130
2
HHCS 1/2 - 13 UNC 1-3/4 PL5
27
00002000
1
HEX CAP 3/8 - 16 X 3/4 GR.5 ZP
28
00012101
1
LOCKWASHER 3/8 PL
29
00011100
1
FLATWASHER 3/8 PL STD
30
00781166
1
FLAT, LH BEARING PIVOT
31
00781167
1
FLAT, RH BEARING PIVOT
32
00781174
1
WELDMENT, SHIELD BRACKET 4 BOLT
00781168
1
WELDMENT, SHIELD BRACET 3 BOLT
33
00786671
1
WLDMT, J/S SHIELD
34
00781175
1
FLAT, REINFORCING STRAP
RX60 - RX72 - RX84 (01-10) Rev 05-11
©2010 Alamo Group Inc.
Parts Section -43
TO THE OWNER/OPERATOR/DEALER
To keep your implement running efficiently and safely, read your manuals thoroughly and follow these directions and
the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the
information you need.
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of
tractor operators:
REQUIRED OF THE OWNER
1.
2.
3.
4.
Provide a Roll-Over-Protective Structure that meets the requirements of this standard.
Provide seat belts that meet the requirements of this paragraph of this standard and SAE J4C.
Ensure that each employee uses such seat belt while the tractor is moving.
Ensure that each employee tightens the seat belt sufficiently to confine the employee to the
protected area provided by the ROPS.
REQUIRED OF THE OPERATOR
1.
2.
3.
4.
5.
6.
7.
8.
9.
Securely fasten seat belt if the tractor has a ROPS.
Where possible, avoid operating the tractor near ditches, embankments, and holes.
Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.
Stay off slopes too steep for safe operation.
Watch where you are going, especially at row ends, on roads, and around trees.
Do not permit others to ride.
Operate the tractor smoothly, no jerky turns, starts, or stops.
Hitch only to the draw bar and hitch points recommended by the tractor manufacturer.
When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all machinery guards
in place...
Please work, drive, play and live each day with care and concern for your safety
and that of your family and fellow citizens.
ALAMO INDUSTRIAL
Limited Warranty
1. Limited Warranties
1.01. Alamo industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser
(“purchaser”) and warrants for six months to the original commercial or industrial purchaser (“purchaser”) that the goods purchased
are free from defects in material or workmanship.
1.02. Manufacturer will replace for the purchaser any part or parts found, upon examination at one of its factories, to be defective under
normal use and service due to defects in material or workmanship.
1.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence,
alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served
its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades,
shields, guards, or pneumatic tires except as specifically found in your operator’s manual.
1.04. Except as provided herein, no employee, agent, dealer, or other person is authorized to give any warranties of any nature on behalf
of manufacturer.
2. Remedies And Procedures
2.01. This limited warranty is not effective unless the purchaser returns the registration and warranty form to manufacturer within 30 days of
purchase.
2.02. Purchaser claims must be made in writing to the authorized dealer (“dealer”) from whom purchaser purchased the goods or an approved
authorized dealer (“dealer”) within 30 days after purchaser learns of the facts on which the claim is based.
2.03. Purchaser is responsible for returning the goods in question to the dealer.
2.04. If after examining the goods and/or parts in question, manufacturer finds them to be defective under normal use and service due to
defects in material or workmanship, manufacturer will:
(A) repair or replace the defective goods or part(s) or
(B) reimburse purchaser for the cost of the part(s) and reasonable labor charges (as determined by manufacturer) if purchaser
paid for the repair and/or replacement prior to the final determination of applicability of the warranty by manufacturer. The choice of
remedy shall belong to manufacturer.
2.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by manufacturer and for returning the
goods to the dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s)
from the dealer to the designated factory.
3. Limitation Of Liability
3.01. Manufacturer disclaims any express (except as set forth herein) and implied warranties with respect to the goods including, but not
limited to, merchantability and fitness for a particular purpose.
3.02. Manufacturer makes no warranty as to the design, capability, capacity, or suitability for use of the goods.
3.03. Except as provided herein, manufacturer shall have no liability or responsibility to purchaser or any other person or entity with respect
to any liability, loss, or damage caused or alleged to be caused directly or indirectly by the goods including, but not limited to, any
indirect, special, consequential, or incidental damages resulting from the use or operation of the goods or any breach of this warranty.
Not withstanding the above limitations and warranties, manufacturer’s liability hereunder for damages incurred by purchaser or others
shall not exceed the price of the goods.
3.04. No action arising out of any claimed breach of this warranty or transactions under this warranty may be brought more than two (2)
years after the cause of action has occurred.
4. Miscellaneous
4.01. Proper venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe county, Texas.
4.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be
a waiver of any other term.
4.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such
provision shall not invalidate any other provisions herein.
4.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
Keep for your records
Attention: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification
when applying for warranty.
Alamo Industrial Implement Model ____________________________ Serial Number ________________________________
Date Purchased __________________________________________ Dealer ______________________________________
Attention:
Read your operator’s manual
ALAMO INDUSTRIAL
1502 E. Walnut
Seguin, Texas 78155
830-379-1480
RX60 - RX72 - RX84 Pub 01-10
P/N 00785503P