Download APC Modular IT

 ISX Modular Power Distribution Unit
1. SYSTEM MAINS SUPPLY RATING
Mains voltage : 3/N/PE-400V/230V, 47—63Hz
Control Voltage : 24V at 50Hz
Short—circuit current lec : 10 kA
Feed : Single
2. SYSTEM EARTHING
The system earthing is IN-S with L1,L2,L3,N,PE at both inlets and outlets
5. STANDARDS
The ISX PDU is built according to : IEC/EN60950
4. ENVIRONMENTS
The assembly is made for an ambient temperature of : Max: +40°C
О. ENCLOSURE
The enclosure of the assembly is : IP20 and Form 1
The assembly material is : Steel with Surface coating
6. POSITIONING
The assembly is made for indoor installation on floor
/. DIMENSIONS AND WEIGHTS
Height : 2002 mm
Width : 300 mm
Depth : 1072 mm
Weight : 160 kg
O. CABLE ENTRIES
Inlets: Outlets:
Top Bottom L ]Sides Top Bottom [1 Sides
9. CONNECTIONS
Power Circuits : Control Circuits :
Input Output
7% И | 77 |
7 ZA Component terminals ZZ Terminals
[| [ ]Busbar
THIS DRAWING AND SPECIFICATIONS HEREIN ARE THE PROPERTY OF TITLE: DWG NO: REV.
SCHNEIDER ELECTRIC AND SHALL NOT BE COPIED, REPRODUCED OR ° ISX MODULAR POWER DISTRIBUTION UNIT P D P M 2 / / H — S P 1
USED IN WHOLE OR IN PART, AS THE BASIS FOR THE MANUFACTURE Schneider Output: Apu: oo 200, 7230 79 POLE | DRAWN: BALAMURUGAN | 13-AUG-08 | ANGLE OF
OR SALE OF ITEMS WITHOUT WRITTEN PERMISSION FROM SCHNEIDER . SPECIFICATIONS
ELECTRIC. THIS DRAWING IS BASED UPON LATEST AVAILABLE LG Electric ENGINEER: SLEE 29-AUG-08 | PROJECTION
INFORMATION AND 15 SUBJECT TOT CHANGE WITHOUT NOTICE. PROJECT: SUBMITTAL DRAWINGS | SHEET 1 OF 7| APPROVED: C.LARSEN/S.WAGH | 29-AUG-08 | Nl . A
i 1000 1000 pp
MINIMUM MINIMUM
200 MINIMUM | i
CLEARANCE CLEARANCE | | CLEARANCE
300 | | 1061 | —37
row poor ss | PERFORATED AREA |
‚ CONSTRUCTED WITH | i Pogo '
PERFORATE
| MATERIAL | [So |
| I o
| | REFER TO
| | DETAIL-B
| | ON PAGE-5
——VIEW-A J
|
2002 ВЫ
| 1415 =
| |
| 986
|
| 986
a +
Li | |
Ha | A= TT 5 W—VE я
3 e 1113 —— DIMETRIC VIEW
FRONT VIEW VIEW—A REAR VIEW
NOTES:
1. INSTALLATION MUST COMPLY WITH NATIONAL AND LOCAL ELECTRICAL REGULATIONS.
2. PLEASE REFER TO APC PRODUCT MANUALS FOR DETAILS.
3. ALL DIMENSIONS ARE IN MILLIMETERS. IX MODULAR DISTRIBUTION, UNI PDPM2//H—MM1 1
4. CABLE ENTRY IS FROM TOP OR BOTTOM OF UNIT. ‚ „ори: 4004, ЗРН- BALAMURUCAN 1 13-AUG-08
5. FRONT, AND REAR ACCESS ARE REQUIRED FOR SERVICE. Outpt 271, UE 100/230 72 POLE SEE Y 79-MUS-08 | ANGE
6. WEIGHT OF THE UNIT IS 160 kg WITHOUT POWER DISTRIBUTION MODULES. SUBLITIAL DRAMNES TShEET 7 OF 7 GLARSEN/SHICH 20-AUC-08 | PROECTON
- 213 - и FOOT (4) -—111—1-4-—925
SE 5 E= = BRUSH
CASTERS (4) 9 e е | ve 2
Yo © = AN BRANCH CABLE EXIT
] CABLE TROUGH = I
| | INSTALLATION = | =
a POINTS(4)-TYP. = | =
o _ | 161 = | =
| PERFORATED AREA | 3 = | =f
000 À — —
Y So N | = =
BRUSH OPENING = | =
Ко! о ЕЕ — | BRANCH CABLE EXIT 276 = | =
= | = o Е | =
= =| = =
/ = = | = | =
120 = | = ==
E ||
INPUT CABLE = = HE
ENTRY AREA 7 = = 5/4 144 = |=
o|E:! = — !
1 = =
— | = 1
= = NPUT CABLE— Го
= = ENTRY AREA So]
= = COMMUNICATION Aq
367 = = PORT m =3| 350
== | 2 si 38
ie a | BE —
© © <C
© © © © 170 I | 33
po | / e e |
| © _ © 86
y ® © = "| B= m | y
|
150— 14 DATA PARTITION | 1-28 —48
_ 271 _ INSTALLATION
POINTS(4)=TYP.
BOTTOM VIEW TOP VIEW
NOTES:
1. INSTALLATION MUST COMPLY WITH NATIONAL AND LOCAL ELECTRICAL REGULATIONS. 6х модуля DISTRIBUTION LNT PDPM2//H-MM2 1
2. PLEASE REFER TO APC PRODUCT MANUALS FOR DETAILS. "Input: 4004, 3PH- ao
3. ALL DIMENSIONS ARE IN MILLIMETERS. Output: 2706, 4008 400/ VIEWS POLE — E aos ANGLE
4. CABLE ENTRY IS FROM TOP OR BOTTOM OF UNIT.
SUBMITTAL DRAWINGS 30F7 CLARSEN/SWAGH | 29—AUG—08 | PROJECTION
INTERNAL FRONT VIEW
NOTES:
1.
2.
3.
A4.
5.
6.
INSTALLATION MUST COMPLY WITH NATIONAL AND LOCAL ELECTRICAL REGULATIONS.
PLEASE REFER TO APC PRODUCT MANUALS FOR DETAILS.
ALL DIMENSIONS ARE IN MILLIMETERS.
ALL POWER DISTRIBUTION MODULES AND EXTENDER CABLES ARE NOT PART OF THIS SKU AND
ARE ORDERED SEPARATELY. PLEASE CONTACT APC.
CONNECTION DETAILS SHOWN ARE TYPICAL. REFER TO SLD FOR DETAILS.
SOME STRUCTURAL DETAILS HAVE BEEN OMITTED FOR CLARITY.
Un m
Y | | $
CORD I
о INPUT TERMINALS
REFER TO I TL а REFER TO
DETAIL-K | Sal PETAL
BAYING BRACKET PACE-5 | ON PAGE-5
(4 PLACES) | A
REFER TO | ool |
PAGE-6 || В
FOR DETAILS | |
о
| |
ens |
||| ||
| |
I |
| il
di
REFER TO
DETAIL-F
ON PAGE-5 Г
o J 1113
|
YING N
| BRACKET A
| REFER TO |
| DETAIL-G !
| ON PAGE-5 |
| | | Г
| | ‚ ‚
| |" ,
| | Lu = $
| | © ©
| à — À
INTERNAL REAR VIEW
Ni Y XL X= xX N Y YX o
\
<
J
|
E
AG {EG
la
==
AM —
LE
ЧН
pe
=
/]
т ©
¡uuu а AB NA === 10) AS
TLL WT TT YT
|
VE
VE”
INTERNAL DIMETRIC VIEW
(ALL PANELS EXCEPT TOP, BOTTOM REMOVED)
PDPM2//H—MET | 1
ISX MODULAR DISTRIBUTION UNIT
t: 400A, 3PH-400V
Input: , —
Output: 277KW, 400A, 400/230V 72 POLE BALAMURUGAN | 13-AUG-08 FIRST
INTERNAL VIEW, CONNECTION DETAILS SIE | 29-AUG-08 ANGLE
SUBMITTAL DRAWINGS 4 OF 7 CLARSEN/SWAGH | 29—AUG—08 | PROJECTION
STATUS CT
Network Management Interface CHECK LOC
10/100 base T
10=Green 100=Orange Computer Interface Display o 0 0 0 e
1 o o o о о o о
О о о o o o o [e]
a | o o o o o o o
Link RX/TX Status J
CORD AT = /
CRITICAL DETAIL—B_ (DISPLAY) MOUNTING CABLE TIE
— PLATE
DETAIL—J (COMMUNICATION INTERFACE) A DETAIL —K
(CORD MOUNTING PLATE)
191 PE 84
PANEL BUS COVER
MODULAR RDP
NEUTRAL |
73 IR |
ce = 137
| MODULE 3 |
| MOUNTING > O o
8 — SLOTS ° |
o o 132
— POWER |
DISTRIBUTION 2 oO
MODULE DN |
> 145
и— NETWORK MANAGEMENT оо |
I INTERFACE LI №
REFER TO DETAIL-J DN В
^^ 150
195 | | |
O
о о 103 o o
т | Ù I
DETAIL—F DETAIL—G
DETAIL—H (INPUT TERMINAL DETAILS)
NOTES:
1. INSTALLATION MUST COMPLY WITH NATIONAL AND LOCAL ELECTRICAL REGULATIONS. SX MODULAR DISTRIBUTION UNIT POPM?2/7/H-=ME? 1
2. PLEASE REFER TO APC PRODUCT MANUALS FOR DETAILS. t: 400A, 3PH-400V
Input:
: BALAMURUGAN | 13—-AUG-08
A3. ALL POWER DISTRIBUTION MODULES AND EXTENDER CABLES ARE NOT PART OF THIS SKU AND Output: 2776, 4004, 400/230V 72 POLE SE | 70-AUC 08 PRDECTON
ARE ORDERED SEPARATELY. PLEASE CONTACT APC. SUBMIIAL DRAMNGS TShEET 5 0F 7 GLRSEN/SMACH 29-AUC-08 IN A
NOT
1.
2.
300
200
ет
|
SLOTS, 4 PLACES
0 REAR | 07}
PDPM277H
|
11
37
) | FRONT | Ô
1194
29—
16
TOP VIEW
(BOLT DOWN BRACKETS
MOUNTING HOLE LOCATIONS)
ES:
INSTALLATION MUST COMPLY WITH NATIONAL AND LOCAL ELECTRICAL REGULATIONS.
TO STABILIZE THE ENCLOSURE (IF IT IS NOT JOINED WITH ANOTHER COMPONENT)
USE THE INCLUDED AR7701 BOLT-DOWN KIT. ATTACH THE BRACKETS TO THE UNIT
AS SHOWN. USE CODE COMPLIANT FASTENERS TO SECURE THE UNIT TO THE FLOOR.
PLEASE REFER TO APC PRODUCT MANUALS FOR DETAILS.
BOLT DOWN
BRACKET
(4—PLACES)
ISOMETRIC VIEW
(BOLT DOWN BRACKETS
MOUNTING DETAIL)
У
THIS DRAWING AND SPECIFICATIONS HEREIN ARE THE PROPERTY OF
SCHNEIDER ELECTRIC AND SHALL NOT BE COPIED, REPRODUCED OR
USED IN WHOLE OR IN PART, AS THE BASIS FOR THE MANUFACTURE
OR SALE OF ITEMS WITHOUT WRITTEN PERMISSION FROM SCHNEIDER
ELECTRIC. THIS DRAWING IS BASED UPON LATEST AVAILABLE
INFORMATION AND IS SUBJECT TO CHANGE WITHOUT NOTICE.
Sepi
TITLE: DWG NO: REV.
ISX MODULAR DISTRIBUTION UNT PDPM2/7/H—AN 0
nput: , -
Output: 2768, 400A, 400/230V 72 POLE | DRANN: BALAMURUGAN | 13-AUG-08 | ANGLE OF
ANCHORING DETAILS ENGINEER: SLEE | 29-AUG-08 | PROJECTION
PROJECT: SUBMITTAL DRAWINGS | SHEET 6 OF 7| APPROVED: CLARSEN/SWAGH | 29-AUG-08 N.A
o O
NDS
>
.
ps d—
a
сч
EEE Ee EE EE NE OE Ee EE EE EN EE DO TN ICO LLL LLL EULER Eee E ELL SELLERS
I-1- "15
BAYING DIMETRIC VIEW
(WITH OFFSET BAYING BRACKET)
NOTES:
1. INSTALLATION MUST COMPLY WITH NATIONAL AND LOCAL ELECTRICAL REGULATIONS.
2. PLEASE REFER TO APC PRODUCT MANUALS FOR DETAILS.
~~
| | I—
OFFSET BAYING BRACKET
(4 PLACES— 2 IN FRONT AND 2 IN REAR OF UNITS)
———l
FLAT BAYING BRACKET
(4 PLACES- 2 IN FRONT AND 2 IN REAR OF UNITS)
BAYING DIMETRIC VIEW
(WITH FLAT BAYING BRACKET)
ISX MODULAR DISTRIBUTION UNIT P D PM2//H—BA
nput: , -
Output: 27M, 400A, 400/230V 72 POLE BALAMURUGAN | 13-AUG-08
BAYING DETAILS SIE | 29-AUC-08
SUBMITTAL DRAWINGS 7057 CLARSEN/SWAGH | 29—AUG-08
0
ANGLE OF
PROJECTION
N.A