Download Chief WBM2 mounting kit

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Interactive Whiteboard Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
WBM2
WBM2
Installation Instructions
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (wood stud or
concrete installations).
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the WBM2 does not exceed 125 lbs
(56.7 kg).
2
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The WBM2 has been designed to be
mounted onto either a 2" x 4" wood stud wall, or an 8" concrete
wall, 8" x 8" x 16" concrete block or clay brick wall.
--SAVE THESE INSTRUCTIONS--
Installation Instructions
WBM2
DIMENSIONS
1192.1
46.93
DIMENSIONS: [MILLIMETERS]
INCHES
3
WBM2
Installation Instructions
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Marcar con lápiz
Befestigungsteil festziehen
Stiftmarkierung
Apertar fixador
Marcar com lápis
Serrare il fissaggio
Segno a matita
Bevestiging vastdraaien
Potloodmerkteken
Serrez les fixations
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Perforar
Befestigungsteil lösen
Bohrloch
Desapertar fixador
Fazer furo
Allentare il fissaggio
Praticare un foro
Bevestiging losdraaien
Gat boren
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Hex-Head Wrench
Destornillador Phillips
Llave de cabeza hexagonal
Kreuzschlitzschraubendreher
Sechskantschlüssel
Chave de fendas Phillips
Chave de cabeça sextavada
Cacciavite a stella
Chiave esagonale
Kruiskopschroevendraaier
Zeskantsleutel
Tournevis à pointe cruciforme
Clé à tête hexagonale
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
4
Installation Instructions
WBM2
TOOLS REQUIRED FOR INSTALLATION
1/8" - wood stud
1/4" - concrete, brick
7/16"
PARTS
B (4)
[Toggler]
E (1)
5/32"
A (4)
1/4"
G (4)
[Isolation washer]
C (4)
1/4-20 x 2-1/2"
H (4)
1/4-20 x 1"
D (2)
[Upright assembly]
F (2)
1/4-20 x 3/8"
J (4)
.500x.320x.425
S (2)
.4 x .255 x .0625
K (1)
[Wall assembly]
L (2)
[Wall bracket cover]
NOTE: No parts "N", "P", "Q", "R" included.
M (2)
[Sliding cover]
5
WBM2
Installation Instructions
ASSEMBLY AND INSTALLATION
Installing to a Wood Stud Wall
The WBM2 will allow an interactive whiteboard to be installed
over an existing chalkboard or whiteboard. The WBM2 may be
installed in the default position which installs in front of
preexisting chalk or marker trays, OR in the low profile position
which installs on the top of preexisting chalk or marker trays.
1.
Determine the center of the chalkboard.
2.
Locate the closest 2" x 4" wood stud to the left and right of
the selected location.
NOTE: The two WBM2 wall brackets on the wall assembly (K)
must be mounted a minimum of 16" (406.4mm) apart,
or a maximum of 42" (1066.8mm) apart.
Locate Mounting Site
3.
Using a level, mark the wall on each stud above existing
chalkboard through top mounting hole in the wall assembly
(K). (See Figure 2)
4.
Drill one 1/8" pilot hole in each stud. (See Figure 2)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! It is the installers
responsibility to make certain the structure to which the
mount is being attached is capable of supporting five times
the weight of the WBM2 and all attached equipment not to
exceed 125 lbs (56.7 kg).
5.
Use two 1/4-20 x 2-1/2" lag bolts (C) and two 1/4" flat washers
(A) to attach wall assembly (K) to wall. (See Figure 2)
6.
Mark the wall through the lower mounting hole in the wall
assembly (K). (See Figure 2)
WARNING: ELECTRICAL SHOCK, EXPLOSION AND
7.
Drill one 1/8" pilot hole in each stud through lower mounting
hole in wall assembly (K). (See Figure 2)
8.
Use two 1/4-20 x 2-1/2" lag bolts (C) and two 1/4" flat washers
(A) to attach wall assembly (K) to wall. (See Figure 2)
FIRE HAZARD! CUTTING OR DRILLING INTO
ELECTRICAL CORDS, CABLES OR GAS PLUMBING CAN
CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surface is free
of electrical wires, cables, gas, water, waste, or any other
plumbing before drilling or installing fasteners.
Adjusting Wall Brackets for Installation
NOTE: The wall brackets on the wall assembly may be
adjusted to suit installation needs, but must be spaced
a minimum of 16" (406.4mm) apart.
1.
Slide wall brackets along wall assembly (K). (See Figure 1)
2.
Tighten button head cap screw on each wall bracket to
secure wall brackets to wall assembly. (See Figure 1)
1
3
4
6
7
(A) x 4
Wall brackets
5
8
2
(C) x 4
x2
(K)
1
Figure 2
Installing to a Concrete, Concrete Block or Clay
Brick Wall
(K)
NOTE: The WBM2 may be attached to an 8" concrete wall,
8" x 8" x 16" concrete block wall or clay brick wall.
1.
(side view)
NOTE: The two WBM2 wall brackets on the wall assembly (K)
Figure 1
NOTE: Proceed to the Installing to a Wood Stud Wall
section, or the Installing to a Concrete, Concrete
Block or Clay Brick Wall section, as appropriate.
6
Determine the center of the chalkboard.
must be mounted a minimum of 16" (406.4mm) apart,
or a maximum of 42" (1066.8mm) apart.
Installation Instructions
2.
WBM2
Using a level, mark the wall above existing chalkboard
through top mounting hole in the wall assembly (K). (See
Figure 3)
4
8
(B) x 4
(D) x 2
Interactive
white board
2
3
6
7
(K)
(G) x 4
(J) x 4
5
9
(A) x 4
(C) x 4
Figure 3
3.
Drill one 1/4" x 2-3/4" pilot hole at each marking. (See
Figure 3)
4.
Install a toggler (B) into both pilot holes using a hammer.
(See Figure 3)
5.
Use two 1/4-20 x 2-1/2" lag bolts (C) and two 1/4" flat
washers (A) to attach wall assembly (K) to anchors in wall.
(See Figure 3)
1
(H) x 4
2
Figure 4
Attaching Uprights to Wall Extrusion
1.
Hook whiteboard with attached uprights onto the wall
asssembly (K). (See Figure 5)
6.
Mark the wall through the lower mounting hole in the wall
assembly (K). (See Figure 3)
2.
Move the slide nut so that it is aligned with the upright (D).
(See Figure 5)
7.
Drill one 1/4" x 2-3/4" pilot hole at each marking through
lower mounting hole in wall assembly (K). (See Figure 3)
3.
8.
Install a toggler (B) into both pilot holes using a hammer.
(See Figure 3)
Fasten upright in place using one 1/4-20 x 3/8" button head
cap screw (F) and one .4"x.255"x.0625" nylon spacer (S).
(See Figure 5)
4.
Repeat for other side of wall extrusion.
9.
Use two 1/4-20 x 2-1/2" lag bolts (C) and two 1/4" flat
washers (A) to attach wall assembly (K) to anchors in wall.
(See Figure 3)
(Interactive
board not
shown)
Attaching Interactive Whiteboard
1.
2.
(K)
Attach upright assembly (D) to back of white board using
four 1/4-20 x 1" Phillips pan head screws (H), four isolation
washers (G) and four .500"x.320"x.425" spacers (J). (See
Figure 4)
Repeat for second upright assembly. (See Figure 4)
Slide nut
1
(F) x 1
3
(D)
(S) x 1
Figure 5
7
WBM2
Installation Instructions
5.
Adjustments
Lateral Movement
1.
Loosen one button head cap screw at top of upright
assembly (D). (See Figure 6)
2.
Slide upright assembly left or right on wall assembly (K), as
necessary. (See Figure 6)
3.
Tighten button head cap screw to fasten upright assembly
into place. (See Figure 6)
Tighten four Phillips head screws (H) into four isolation
washers (G) and spacers (J) to fasten white board to upright
assembly (D). (See Figure 8)
(G)
(D)
(J)
4
(K)
4
2
3
5
(H) x 4
(D)
1
3
Figure 8
x1
Figure 6
6.
Hook whiteboard with attached uprights onto the wall
assembly (K). (See Figure 7)
7.
Tighten button head cap screw with spacer (loosened in
Step 1) at top of each upright assembly to fasten upright
assemblies (D) into place. (See Figure 7)
Vertical Adjustment
1.
Loosen one button head cap screw with spacer at top of
each upright assembly (D). (See Figure 7)
2.
Unhook whiteboard from wall assembly (K). (See Figure 7)
Micro Height Adjust and Leveling
1.
(Interactive
board not
shown)
The wall assembly (K) can be adjusted or leveled by turning
the hex head bolt in the brackets. (See Figure 9)
•
Turn clockwise to raise wall assembly
•
Turn counterclockwise to lower wall assembly.
Sliding nut
(K)
1
(Interactive
board not
shown)
7
x2
6
(K)
2
(D)
LOWER
1
RAISE
Figure 7
3.
Loosen four Phillips head screws on back of white board.
(See Figure 8)
4.
Adjust white board up or down, as required. (See Figure 8)
8
Figure 9
Installation Instructions
WBM2
Adding Covers
1.
Open the lower flaps of the wall bracket cover (L) outward.
(See Figure 10)
2.
Slide the cover downward, hooking the top of the wall
bracket covers (L) onto the tabs on top of wall assembly
brackets. (See Figure 10)
3.
Slide the lower flaps of the wall bracket cover (L) under the
bottom of the wall assembly brackets (K). (See Figure 10)
(M)
4
(M)
(L)
(L)
1
(K)
1
Wall
bracket
tab
2
Figure 11
Figure 10
4.
Slide the sliding cover (M) down over the wall bracket cover
(L). (See Figure 11)
9
WBM2
10
Installation Instructions
Installation Instructions
WBM2
11
WBM2
Installation Instructions
USA/International
Europe
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002101 Rev07
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
07/12
Asia Pacific
A
P
F
A
P
F
A
6436 City West Parkway, Eden Prairie, MN 55344
800.582.6480 / 952.225.6000
877.894.6918 / 952.894.6918
Franklinstraat 14, 6003 DK Weert, Netherlands
+31 (0) 495 580 852
+31 (0) 495 580 845
Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477