Download Netra 20 Server Release Notes
Transcript
LW2+RelNote.P21.book Page 1 Thursday, September 25, 2003 11:18 AM Netra™ 20 Release Notes Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U.S.A. 650-960-1300 Part No. 816-1307-17 August 2003, Revision A Send comments about this document to: [email protected] LW2+RelNote.P21.book Page 2 Thursday, September 25, 2003 11:18 AM Copyright 2003 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. Sun Microsystems, Inc. has intellectual property rights relating to technology embodied in the product that is described in this document. In particular, and without limitation, these intellectual property rights may include one or more of the U.S. patents listed at http://www.sun.com/patents and one or more additional patents or pending patent applications in the U.S. and in other countries. This document and the product to which it pertains are distributed under licenses restricting their use, copying, distribution, and decompilation. No part of the product or of this document may be reproduced in any form by any means without prior written authorization of Sun and its licensors, if any. Third-party software, including font technology, is copyrighted and licensed from Sun suppliers. Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in the U.S. and in other countries, exclusively licensed through X/Open Company, Ltd. Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, and Solaris are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and in other countries. All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. in the U.S. and in other countries. Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems, Inc. The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN LOOK GUIs and otherwise comply with Sun’s written license agreements. U.S. Government Rights—Commercial use. Government users are subject to the Sun Microsystems, Inc. standard license agreement and applicable provisions of the FAR and its supplements. DOCUMENTATION IS PROVIDED "AS IS" AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID. Copyright 2003 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, Etats-Unis. Tous droits réservés. Sun Microsystems, Inc. a les droits de propriété intellectuels relatants à la technologie incorporée dans le produit qui est décrit dans ce document. En particulier, et sans la limitation, ces droits de propriété intellectuels peuvent inclure un ou plus des brevets américains énumérés à http://www.sun.com/patents et un ou les brevets plus supplémentaires ou les applications de brevet en attente dans les Etats-Unis et dans les autres pays. Ce produit ou document est protégé par un copyright et distribué avec des licences qui en restreignent l’utilisation, la copie, la distribution, et la décompilation. Aucune partie de ce produit ou document ne peut être reproduite sous aucune forme, parquelque moyen que ce soit, sans l’autorisation préalable et écrite de Sun et de ses bailleurs de licence, s’il y ena. Le logiciel détenu par des tiers, et qui comprend la technologie relative aux polices de caractères, est protégé par un copyright et licencié par des fournisseurs de Sun. Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd. Sun, Sun Microsystems, le logo Sun, AnswerBook2, docs.sun.com, et Solaris sont des marques de fabrique ou des marques déposées de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays. Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc. aux Etats-Unis et dans d’autres pays. Les produits protant les marques SPARC sont basés sur une architecture développée par Sun Microsystems, Inc. L’interface d’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun reconnaît les efforts de pionniers de Xerox pour la recherche et le développment du concept des interfaces d’utilisation visuelle ou graphique pour l’industrie de l’informatique. Sun détient une license non exclusive do Xerox sur l’interface d’utilisation graphique Xerox, cette licence couvrant également les licenciées de Sun qui mettent en place l’interface d ’utilisation graphique OPEN LOOK et qui en outre se conforment aux licences écrites de Sun. LA DOCUMENTATION EST FOURNIE "EN L’ÉTAT" ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE, Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A L’APTITUDE A UNE UTILISATION PARTICULIERE OU A L’ABSENCE DE CONTREFAÇON. Please Recycle LW2+RelNote.P21.book Page 3 Thursday, September 25, 2003 11:18 AM Release Notes This document lists the changes between the printed manuals and your delivered Netra 20 AC and DC systems. The system was initially released as the Netra T4 AC100 supported by a manual set specifically for the AC version of the server. These manuals were all at revision -10. Subsequently, a DC version was released as the Netra T4 DC100 and delivered with an updated manual set covering both the AC and DC versions of the server. These manuals were all at revision -11. The most recent manual set incorporates the change of name to the Netra 20 server and includes information about the new 900 MHz UltraSPARC III+ processor. This manual set comprises the following documents: ■ ■ ■ ■ Netra Netra Netra Netra 20 20 20 20 Compliance and Safety Manual (part no. 816-5279) Installation and User’s Guide (part no. 806-7334) Service and System Reference Manual (part no. 806-7336) Release Notes—this document (part no. 816-1307) Note – Use these release notes only in conjunction with the latest manual set. The document contains: ■ “Delivered CDs for Updates 4/01, 7/01 and 10/01” on page 4 This section contains important information relating to the correct instgallation CD to use when installing Solaris 8 Updates 4/01, 7/01 and 10/01. ■ “Points You Should Note” on page 6 This section highlights points of particular importance in ensuring that your system operates satisfactorily. ■ “Software Issues” on page 7 This section describes important bugs known immediately prior to the delivery of your Netra 20 system. 3 LW2+RelNote.P21.book Page 4 Thursday, September 25, 2003 11:18 AM ■ “Compliance Statement” on page 9 This section contains a compliance statement which should be considered as part of the Netra 20 Compliance and Safety Manual. Delivered CDs for Updates 4/01, 7/01 and 10/01 The following installation CDs are supplied with the system for use with Solaris 8 Updates 4/01, 7/01 and 10/01 only. ■ A combined installation CD for Solaris 8 Update 4/01, Update 7/01 and Update 10/01, to be used in conjunction with the corresponding Solaris 8 media kit (this installs the US-English version of the software) ■ A combined multilingual installation CD for Solaris 8 Update 4/01, Update 7/01 and Update 10/01 to be used in conjunction with the corresponding update of the multilingual Solaris 8 media kit (this installs the Asian and European, including European English, version of the software) Do not discard these CDs; they are essential for the Netra 20 installation procedure. The CDs replace the installation CD supplied with the corresponding Solaris media kit. Refer to Chapter 5 of the Netra 20 Installation and User’s Guide for details of the installation procedure. Note – For Update 2/02 and later, use the installation CD supplied with the Solaris media kit. Refer to chapter 6 of the Netra 20 Installation and User’s Guide. Caution – Ensure that you use the correct installation CD and Solaris media kit combination, as shown in TABLE 1. 4 Netra 20 Release Notes • August 2003 LW2+RelNote.P21.book Page 5 Thursday, September 25, 2003 11:18 AM TABLE 1 Choosing the Correct Installation CD If you are installing ... ... and have these Solaris 8 CDs ... ... use this installation CD Update 4/01 704-7562-10 704-7563-10 704-7650-10 704-7601-10 (Solaris 8 CD 1 of 2) (Solaris 8 CD 2 of 2) (Documentation) (Supplemental) 704-0039-10 Update 7/01 704-7665-10 704-7666-10 704-7795-10 704-7704-10 (Solaris 8 CD 1 of 2) (Solaris 8 CD 2 of 2) (Documentation) (Supplemental) 704-0039-10 Update 10/01 704-7826-10 704-7827-10 704-7930-10 704-7928-10 (Solaris 8 CD 1 of 2) (Solaris 8 CD 2 of 2) (Documentation) (Supplemental) 704-0039-10 Update 4/01 (Multilingual) 704-7562-10 704-7563-10 704-7681-10 704-7680-10 704-7522-10 (Solaris 8 CD1 of 2) (Solaris 8 CD2 of 2) (Documentation European) (Documentation Asian) (Supplemental) 704-0041-10 Update 7/01 (Multilingual) 704-7665-10 704-7666-10 704-7796-10 704-7797-10 704-7645-10 (Solaris 8 CD1 of 2) (Solaris 8 CD2 of 2) (Documentation European) (Documentation Asian) (Supplemental) 704-0041-10 Update 10/01 Multilingual) 704-7826-10 704-7827-10 704-7942-10 704-7943-10 704-7813-10 (Solaris 8 CD 1 of 2) (Solaris 8 CD 2 of 2) (Documentation European) (Documentation Asian) (Supplemental) 704-0041-10 Update 2/02 Standard Solaris installation using the CDs in the media kit Use the installation CD in the media kit Release Notes 5 LW2+RelNote.P21.book Page 6 Thursday, September 25, 2003 11:18 AM Points You Should Note System Configuration Card The system configuration card must be present and properly seated in your system at all times. In particular, note that: ■ ■ The system will not boot if the configuration card is not present. If you remove the configuration card from a working system, the system will shut down after 60 seconds. Note – The system configuration card can become dislodged when the system is in transit. While this may not be obvious visually, it can be enough to prevent the system from booting. Before switching on the system for the first time, ensure that the card is fully seated in the card reader. Sacrificial Brackets Remove the orange sacrificial brackets before installing the system in a rack. RJ45 LOMlite2 Serial Cable A shielded RJ45 to RJ45 serial cable and RJ45 to DB-25 adaptor is supplied with the system to enable connection to the LOMlite2 serial port. Note – The LOMlite2 serial port is the default serial port. 6 Netra 20 Release Notes • August 2003 LW2+RelNote.P21.book Page 7 Thursday, September 25, 2003 11:18 AM Software Issues This section describes software issues relating to your Netra 20 system and lists other known platform-specific software bugs. Serial Ports ttya and ttyb are incorrectly named in the software. TABLE 2 shows the /dev/term entries for the hardware ports. TABLE 2 Hardware Port Entries in /dev/term Hardware Port /dev/term Entry ttya /dev/term/b ttyb /dev/term/c lom-console /dev/term/a 4462131 The LOMlite2 reset-x command does not currently reset the CPUs. This will be fixed in a later revision of the OBP. 4476916 Following an upgrade of the LOMlite2 firmware using the lom -G default command at the Unix prompt, the system should return to the shell prompt. However, the system occasionally displays the OBP ok prompt instead after successfully downloading the firmware. If this occurs, type go to return to the Unix prompt. 4483972 If a break is sent on the console while OBP is resetting or starting up, the OBP initialization is interrupted. As a result, the platform name is not set to SUNW,Netra-T4 and, therefore, when Solaris boots, the platform identity is incorrect and the lombus driver is not loaded. Release Notes 7 LW2+RelNote.P21.book Page 8 Thursday, September 25, 2003 11:18 AM To recover, reboot the system. To prevent this occurring do not interrupt the OBP startup process. If you interrupt the process by mistake, type reset-all at the ok prompt before rebooting Solaris. 4485823 When /platform/sun4u/kernel/dev/lomv.conf parameter serial_timeout has been enabled (by setting its value to 1), and the lom output is not shared with general console output on the LOMlite2 port (by setting input-device and output-device to ttya), the message [returning to system console] is displayed at the lom console instead of ttya following a lom session timeout. To return to the lom> prompt, type #. at the lom console. 4488811 The multilingual installation CDs supplied with the Netra 20 system for Solaris 8 Updates 4/01 and 7/01 require the multilingual Solaris media kit. If you have the English-only media kit, see the comment at the end of “Delivered CDs for Updates 4/01, 7/01 and 10/01” on page 4. Other Known Bugs TABLE 3 is a listing of the currently known platform-specific software and firmware bugs. TABLE 3 8 Known Netra 20 Platform Software and Firmware Bugs 4428172 4479032 4483972 4508483 4525941 4668704 4450601 4479499 4485823 4508485 4528323 4673741 4452208 4479510 4488811 4508799 4531241 4454398 4479513 4492752 4512866 4531756 4462281 4480643 4497117 4512874 4531772 4469287 4481061 4498701 4519172 4617086 4469844 4481063 4499277 4520559 4623249 4471054 4481074 4500254 4522850 4636549 Netra 20 Release Notes • August 2003 LW2+RelNote.P21.book Page 9 Thursday, September 25, 2003 11:18 AM TABLE 3 Known Netra 20 Platform Software and Firmware Bugs (Continued) 4475101 4481180 4500350 4522856 4636569 4476916 4481822 4502571 4522857 4640565 4477222 4482930 4502640 4522860 4652816 4477408 4483386 4504487 4522863 4657432 4477437 4483484 4504994 4522917 4658786 Compliance Statement The following compliance statement should be added to the Netra 20 Compliance and Safety Manual. CCC Statement Release Notes 9 LW2+RelNote.P21.book Page 10 Thursday, September 25, 2003 11:18 AM 10 Netra 20 Release Notes • August 2003