Download SERVICE MANUAL

DVP-S9
SERVICE MANUAL
AEP Model
UK Model
E Model
Australian Model
Ver 1.7 2004.09
DVP-S9 is the DVD/Video CD/CD player
section in MHC-S9D.
Model Name Using Similar Mechanism
NEW
CD Mechanism Type
CDM63D
Optical Pick-up Name
KHM-240AAA (TYPE A)
KHM-270AAA (TYPE B)
SPECIFICATIONS
DVD/Video CD/CD player section
Laser
Frequency response
Signal-to-noise ratio
Dynamic range
Video color system format
Semiconductor laser
(λ=660 nm/780 nm)
Emission duration:
continuous
DVD (PCM 48 kHz):
2 Hz – 22 kHz = (±1 dB)
CD: 2Hz – 20 kHz =
(±1 dB)
More than 90 dB
More than 90 dB
NTSC, PAL
OPTICAL OUT
(Square optical connector jack, rear panel)
General
Power requirements
European model:
Australian model:
Mexican model:
Korean model:
Thailand model:
Other models:
230 V AC, 50/60 Hz
230 – 240 V AC,
50/60 Hz
120 V AC, 60 Hz
220 V AC, 60 Hz
220 V AC, 50/60 Hz
120 V, 220 V or
230 – 240 V AC,
50/60 Hz
Dimensions (w/h/d)
Approx. 280 x 108 x 330 mm
Mass
Approx. 2.9 kg
Design and specifications are subject to change
without notice.
DVD/VIDEO CD/CD PLAYER
9-873-280-08
Sony Corporation
2004I05-1
© 2004.09
Audio Group
Published by Sony Engineering Corporation
DVP-S9
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
This appliance is
classified as a CLASS 1
LASER product. The
CLASS 1 LASER
PRODUCT MARKING
is located on the rear
exterior.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
As the laser beam used in this CD/DVD Player is
harmful to eyes, do not attempt to disassemble the
cabinet. Refer servicing to qualified personnel only.
The following caution label is located inside the
apparatus.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board. (within 3 times)
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
DVP-S9
TABLE OF CONTENTS
1.
SERVICING NOTES ............................................... 3
2.
GENERAL ................................................................... 5
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
Disassembly Flow ...........................................................
Cover ...............................................................................
CD Mechanism Deck (CDM63D) ..................................
MB Board ........................................................................
VIDEO Board ..................................................................
MAIN Board ...................................................................
Front Panel Section .........................................................
PANEL Board, SUB PANEL Board ...............................
Lid (CD) ..........................................................................
4.
TEST MODE .............................................................. 11
6
7
7
8
8
9
9
10
10
SECTION 1
SERVICING NOTES
This set is a component of the MHC-S9D.
The MHC-S9D system configuration is as shown below, and therefore it does not operate normally unless all four components are
connected.
In performing the repair, connect all components with the system
cables.
Note: The precaution to the users is described on the label stuck on the
back panel (DVD/video CD/CD player) and in the troubleshooting
section in the Operation Manual.
System Configuration:
TA
AC IN
POWER SUPPLY
5.
ELECTRICAL ADJUSTMENTS ......................... 22
6.
DIAGRAMS
6-1.
6-2.
6-3.
6-4.
6-22.
Block Diagram – RF/SERVO Section – ........................
Block Diagram – MAIN Section (1/2) – .......................
Block Diagram – MAIN Section (2/2) – .......................
Block Diagram
– INTERFACE CONTROL Section – ............................
Note For Printed Wiring Boards
and Schematic Diagrams ................................................
Printed Wiring Board – RF Board – ..............................
Schematic Diagram – RF Board – .................................
Printed Wiring Boards – DISC SENSOR/DRIVER/
IN OUT SW/MOTOR/TRAY SENSOR Boards – .........
Schematic Diagram – DISC SENSOR/DRIVER/
IN OUT SW/MOTOR/TRAY SENSOR Boards – .........
Printed Wiring Board
– MB Board (Component Side) – ...................................
Printed Wiring Board
– MB Board (Conductor Side) – .....................................
Schematic Diagram – MB Board (1/6) – .......................
Schematic Diagram – MB Board (2/6) – .......................
Schematic Diagram – MB Board (3/6) – .......................
Schematic Diagram – MB Board (4/6) – .......................
Schematic Diagram – MB Board (5/6) – .......................
Schematic Diagram – MB Board (6/6) – .......................
Printed Wiring Board – MAIN Board – ........................
Schematic Diagram – MAIN Board – ...........................
Printed Wiring Boards
– PANEL/SUB PANEL/VIDEO Boards – .....................
Schematic Diagram
– PANEL/SUB PANEL/VIDEO Boards – .....................
IC Pin Function Description ...........................................
7.
EXPLODED VIEWS
7-1.
7-2.
7-3.
7-4.
7-5.
7-6.
7-7.
7-8.
Case Section ....................................................................
Front Panel Section .........................................................
Chassis Section ...............................................................
CD Mechanism Deck Section-1 (CDM63D) .................
CD Mechanism Deck Section-2 (CDM63D) .................
CD Mechanism Deck Section-3 (CDM63D) .................
CD Mechanism Deck Section-4 (CDM63D) .................
Optical Pick-up Section ..................................................
8.
ELECTRICAL PARTS LIST ............................... 65
6-5.
6-6.
6-7.
6-8.
6-9.
6-10.
6-11.
6-12.
6-13.
6-14.
6-15.
6-16.
6-17.
6-18.
6-19.
6-20.
6-21.
23
24
25
26
27
28
29
ST
MASTER & GRAPHIC µcon
DISPLAY
DVP
30
HTC & MB µcon
31
POWER BLOCK
32
33
34
35
36
37
38
39
40
41
TC
TC µcon
42
43
47
57
58
59
60
61
62
63
64
3
DVP-S9
Ver 1.7
NOTE OF REPLACING THE MB BOARD
When replacing the MB board, since the adjustment value is not
set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.
MODEL IDENTIFICATION
- Back Panel -
Procedure:
1. Set the test mode. (See page 12)
2. Press the [2] key of the remote commander, and set the “DRIVE
MANUAL OPERATION”. (See page 18)
3. Press the [6] key of the remote commander, and set the “2-6,
Memory Check”. (See page 20)
4. Press the [CLEAR] key of the remote commander, and initialize Memory.
PART No.
Model
PART No.
AEP model
4-236-808-0[]
UK model
4-236-808-1[]
Korean model
4-236-808-3[]
Singapore model
4-236-808-4[]
Saudi Arabia model
4-236-808-5[]
Austrarian model
4-236-808-6[]
Thai model
4-236-808-7[]
E model
4-236-808-8[]
Mexican model
4-236-808-9[]
TYPE A/B DISCRIMINATION
optical device
SILVER: KHM-240AAA (TYPE A)
BLACK: KHM-270AAA (TYPE B)
SERVICE POSITION
In checking the CD block and another board, prepare jigs (extension cable J-2501-155-A: 300 mm 9 cores, J-2501-199-A: 300 mm 25
cores, J-2501-202-A: 300 mm 8 cores).
VIDEO board
Connect jig (extension cable J-2501-155-A)
to the MB board (CN015) and optical pick-up block.
RF board
optical pick-up block
Connect jig (extension cable J-2501-202-A)
to the MB board (CN012) and VIDEO board (CN201).
4
MB board
Connect jig (extension cable J-2501-199-A)
to the MB board (CN010) and RF board (CN002).
DVP-S9
SECTION 2
GENERAL
This section is extracted from
instruction manual.
Parts Identification
The items are arranged in alphabetical order.
Refer to the pages indicated in parentheses ( ) for details.
Main unit
Remote control
DVD/VIDEO CD/CD player
1
rd
1 2 345
es ed
wl e;ea
2
rs
DISC 1–3 rd (25, 26)
DISC 1–3 indicators rs
DISC 1–3 Z (eject) ea (25, 26)
NEXT el (26, 27)
PLAY MODE wl (25, 28, 29, 46)
PREV ra (26, 27)
REPEAT e; (12, 30)
RETURN O ej (12, 27, 39, 40)
N SELECT (play) r; (25–27,
41, 55, 60)
X (pause) ek (26)
x (stop) eh (12, 26, 27, 30, 38,
45, 55, 61)
. (go back) eg (26, 28, 30)
> (go forward) ef (26, 28, 30)
m (rewind) es (26)
M (fast forward) ed (26)
3
m
M
.
>
H
S
x
r; ek eh
ra el ej
ef
eg
rl
rk
rj
rh
rg
rf
rd
rs
ra
r;
el
ek
ej
eh
eg
ef
ed
es
ea
e;
wl
6
7
O
nN
x
.
>
m
M
X
c
C
t
T
8
9
q;
qa
qs
qd
qf
qg
qh
qj
qk
ql
w;
wa
ws
wd
wf
V
wk
B
b
wg
v
wh
wj
ANGLE es (37)
AUDIO ws (34)
CLEAR qs (22, 29, 30, 36)
CLOCK/TIMER SELECT 3
(47, 56)
CLOCK/TIMER SET 2 (17, 47,
56)
DBFB ra (48)
D.SKIP 9 (26)
DIGITAL rf (57)
DISPLAY rj (17, 31, 32, 43, 54)
DVD DISPLAY wd (18, 19, 30,
32–34, 36–40)
DVD MENU wa (27)
DVD SET UP ql (18, 19, 24, 39)
ENTER wj
EQ ea (52)
EQ ON/OFF wl (53)
FILE SELECT +/– wh (48, 49,
53)
FUNCTION rd (18, 25, 27, 28,
36, 45, 46, 55, 57)
GROOVE rs (48)
KARAOKE PON (Except for
North American and European
models) el (54)
MD rh (57)
Numeric buttons 8 (28, 30)
PLAY MODE qa (25, 28, 29, 46)
REPEAT q; (30)
RETURN O qd (27, 39, 40)
SELECT DVD N eh (20, 25,
27, 29, 30)
SET UP wf (14, 16, 51, 53, 54)
SLEEP 1 (55)
SLOW t/T qk (26)
SPECTRUM ANALYZER rk
(54)
STEP c/C ef (26)
SUBTITLE ed (37)
SUR e; (51)
TAPE A nN ek (44)
TAPE B nN qf (44, 45)
TITLE w; (27)
TUNER/BAND ej (42)
TV @/1 4 (13)
TV CH +/– 7 (13)
TV/VIDEO rl (13)
TV VOL +/– 6 (13)
VIDEO rg (57)
VOL +/– wg
BUTTON DESCRIPTIONS
@/1 (power) 5
X (pause) qj
x (stop) qg
m/M (rewind/fast forward),
TUNING –/+ qh
./> (go back/go forward),
PRESET –/+, PREV/NEXT eg
O/o/P/p wk
>10 r;
5
DVP-S9
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SET
3-2. COVER
(Page 7)
3-3. CD MECHANISM DECK
(CDM63D)
(Page 7)
3-4. MB BOARD
(Page 8)
3-5. VIDEO BOARD
(Page 8)
3-6. MAIN BOARD
(Page 9)
3-7. FRONT PANEL SECTION
(Page 9)
3-8. PANEL BOARD,
SUB PANEL BOARD
(Page 10)
3-9. LID (CD)
(Page 10)
6
DVP-S9
Note: Follow the disassembly procedure in the numerical order given.
3-2.
COVER
3 cover
2 screw
(BVTT3 × 6)
1 two screws
(case 3 TP2)
1 two screws
(case 3 TP2)
3-3.
CD MECHANISM DECK (CDM63D)
4 CD mechanism deck
(CDM63D)
2 connector
(CN701)
5 wire (flat type) (25 core)
(CN010)
1 wire (flat type) (9 core)
(CN015)
3 four screws
(BVTP3 × 8)
7
DVP-S9
3-4.
MB BOARD
1 wire (flat type) (9 core)
(CN015)
1 wire (flat type) (8 core)
(CN011)
4 two screws
(BV)
5 lug
4 two screws
(BV)
6 MB board
2 wire (flat type) (25 core)
(CN010)
3 connector
(CN008)
3-5.
VIDEO BOARD
2 connector
(CN202)
1 wire (flat type) (8 core)
4 VIDEO board
3 three screws
(BVTP3 × 8)
8
DVP-S9
3-6.
MAIN BOARD
3 two connectors
(CN101, 102)
1 wire (flat type) (10 core)
(CN107)
9 MAIN board
2 connector
(CN401)
7 screw
(BVTP3 × 8)
5 screw
(BVTP3 × 8)
8 screw
(BVTP3 × 8)
6 lug
4 connector
(CN701)
3-7.
FRONT PANEL SECTION
1 connector
(CN401)
3 claw
4 front panel section
3 two claws
2 three screws
(BVTP3 × 8)
9
DVP-S9
3-8.
PANEL BOARD, SUB PANEL BOARD
4 four screws
(BVTP2.6 × 8)
6 SUB PANEL board
5 two claws
1 five screws
(BVTP2.6 × 8)
3 PANEL board
2 two claws
3-9.
LID (CD)
2 bracket (LID) assy
1 screw
(BVTP2.6 × 8)
4 spring (CD)
3 lid (CD)
10
DVP-S9
SECTION 4
TEST MODE
Note: Use following buttons in the test mode.
no mark : Button of DVD/video CD/CD player (DVP-S9)
*1 : Button of A/V amplifier (TA-S9D)
*2 : Button of tuner (ST-S9)
[CHANGE-OVER THE COLOR SYSTEM]
• The color system can be changed over NTSC or PAL.
Procedure:
1. Press the I/1 *1 button to turn the power on.
2. Turn the [FUNCTION]*1 knob to select “DVD”, and press
the x button.
3. While pressing the both [RETURN] and [REPEAT] buttons,
turn the power off.
4. Press the I/1 *1 button to turn the power on. The color system is changed over.
[COLD RESET]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure 1:
1. Press the I/1 *1 button to turn the power on.
2. While pressing the both [PLAY MODE] and x buttons, press
the M button.
3. The set is reset, and becomes standby state.
Procedure 2:
1. Press the I/1 *1 button to turn the power on.
2. While pressing the [DIGITAL]*1 button, press the [DISPLAY]*2
button.
3. The set is reset, and becomes standby state.
[DVD DELIVERY MODE]
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the I/1 *1 button to turn the power on.
2. Turn the [FUNCTION]*1 knob to select “DVD”.
3. While pressing the [EQ ON/OFF]*1 button, press the I/1 *1
button.
4. The message “LOCK” is displayed on the fluorescent indicator tube of tuner unit and turn the power off automatically, and
the DVD delivery mode is set.
[GC TEST MODE]
Enter the GC Test Mode
Procedure 1:
1. Press the I/1 *1 button to turn the power on.
2. While pressing the both [PLAY MODE] and x buttons, press
the Z (DISC 1) button.
3. LEDs and fluorescent indicator tube are all turned on of all
units.
Procedure 2:
1. Press the I/1 *1 button to turn the power on.
2. While pressing the both [STEREO/MONO]*2 and
[CINEMA STUDIO C]*1 buttons, press the [CLOCK/TIMER]*2
button.
3. LEDs and fluorescent indicator tube are all turned on of all
units.
Version Display Mode
Procedure:
1. Enter the GC test mode.
2. Each time the [DISC 1] or [TUNER MEMORY]*2 button is
pressed, microcomputer or mechanism deck version is displayed of each unit.
3. Press the [DISC 3] or [TUNING +]*2 button to detail is displayed the version.
Key Check Mode
Procedure:
1. Enter the GC test mode.
2. Press the [DISC 2] or [TUNING --]*2 button to set the key check
mode, and displays “K 0 J 0 V 0” on the fluorescent indicator
tube of tuner unit.
3. All buttons are pressed of video CD unit, all LEDs are blinking of video CD unit. (not change the display of fluorescent
indicator tube)
Releasing the GC Test Mode
To release from this mode, press three buttons in the same manner
as entering this mode or disconnect the power cord.
[DVD SERVICE MODE]
• This mode can run the DVD sled motor optionally. Use this
mode, for instance, when cleaning the optical pick-up.
Procedure:
1. Press the I/1 *1 button to turn the power on.
2. Turn the [FUNCTION]*1 knob to select “DVD”.
3. While pressing the both [PLAY MODE] and x buttons, press
the . button.
4. Set to the DVD service mode.
5. With the DVD in stop status, press the M button to move
the optical pick-up to outside track, or press the m button
to inside track.
6. To release from this mode, perform as follows.
1) Move the optical pick-up to the most inside track.
2) Disconnect the power cord.
Notes: • Always move the optical pick-up to most inside track when
releasing from this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can
be chipped.
[DVD CANCELLATION MODE OF REPEAT LIMITATION]
• This mode can cancel the DVD repeat limitation (5 times).
Procedure:
1. Press the I/1 *1 button to turn the power on.
2. Turn the [FUNCTION]*1 knob to select “DVD”.
3. While pressing the both [PLAY MODE] and x buttons, press
the [REPEAT] button.
4. DVD repeat limitation is canceled.
5. To release this mode, disconnect the power cord.
[DVD DISC TRAY LOCK MODE FOR BURGLARY
PREVENTION]
Procedure:
1. Press the I/1 *1 button to turn the power on.
2. Turn the [FUNCTION]*1 knob to select “DVD”.
3. While pressing the both [PLAY MODE] and x buttons, press
the m button, turn the power off.
11
DVP-S9
Ver 1.6
[GENERAL DESCRIPTION]
The Test Mode allows you to make diagnosis and adjustment easily using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
[STARTING TEST MODE]
1.
2.
3.
4.
Press the I/1 *1 button to turn the power on.
Turn the [FUNCTION]*2 knob to select “DVD”.
While pressing the x and [PLAY MODE] button, press
the . button to enter the test mode.
It displays “TEST MODE” on the fluorescent indicator tube,
and displays the Test Mode Menu on the monitor screen as
follows. (At the bottom of the menu screen, the model name
and revision number are displayed)
1. All
All items continuous check
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically unless an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is displayed for the key entry.
### Syscon Diagnosis ###
Diag All Check
No. 2 Version
2-3. ROM Check Sum
Check Sum = 2005
Test Mode Menu
0.
1.
2.
3.
4.
5.
6.
Syscon Diagnosis
Drive Auto Adjustment
Drive Manual Operation
Mecha Aging
Emergency History
Version Information
Video Level Adjustment
Exit: POWER Key
_
Model
: xxx-xxxx_xx
Revision: 1.xxx
5.
6.
To execute each function, select the desired menu and press its
number on the remote commander (RM-SD390AV or RMSD395AV).
To release from test mode, press the I/1 *1 button and turn
the power off.
Press NEXT Key to Continue
Press PREV Key to Repeat
_
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press > key to go to the next item,
or . key to repeat the same check again. To quit the diagnosis
and return to the Check Menu screen, press x or [ENTER] key.
If an error occurred, the diagnosis is suspended and the error code
is displayed as shown below.
### Syscon Diagnosis ###
[SYSCON DIAGNOSIS]
The same contents as board detail check by serial interface can be
checked from the remote commander.
On the Test Mode Menu screen, press [10/0] key on the remote
commander, and the following check menu will be displayed.
0.
1.
2.
3.
4.
5.
6.
7.
8.
### Syscon Diagnosis ###
Check Menu
Quit
All
Version
Peripheral
Servo
Supply
AV Decoder
Video
Audio
_
0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
12
3-3. EEPROM Check
Error 03: EEPROM Write/Reed N
Address
: 00000001
Write Data : 2492
Read Data : 2490
Press NEXT Key to Continue
Press PREV Key to Repeat
_
Press x key to quit the diagnosis, or > key to repeat the same
item where an error occurred, or . key to continue the check
from the item next to faulty item.
DVP-S9
Ver 1.6
Selecting 2 and subsequent items calls the submenu screen of each
item.
For example, if “5. Supply” is selected, the following submenu
will be displayed.
0.
1.
2.
3.
4.
5.
_
### Syscon Diagnosis ###
Check Menu
No. 5 Supply
Quit
All
ARP Register Check
ARP to RAM Data Bus
ARP to RAM Address Bus
ARP RAM Check
0. Quit
Quit the submenu and return to the main menu.
1. All
All submenu items continuous check
This menu checks 2 and subsequent items successively. At the item
where visual check is required for judgment or an error occurred,
the checking is suspended and the message is output for key entry.
Normally, all items are checked successively one after another automatically unless an error is found.
Selecting 2 and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “Check Items List”.
General Description of Checking Method
2. Version
(2-2) Revision
ROM revision number is displayed.Error: Not detected.
The revision number defined in the source file of ROM (At
the beginning of mass production, the Flash ROM of IC107
is used) is displayed with four digits.
(2-3) ROM Check Sum
Check sum is calculated.
Error: Not detected.
The 8-bit data are added at addresses 0x000F0000 ~
0x002EFFFF of ROM (IC107) and the result is displayed
with 4-digit hexadecimal number. Error is not detected.
Compare the result with the specified value.
(2-4) Model Type
Model code is displayed.
Error: Not detected.
The model code read from EEPROM (IC101) is displayed
with 2-digit hexadecimal number.
(2-5) Region
Region code is displayed.
Error: Not detected.
The region code determined from the model code is displayed.
3.
Peripheral
(3-2) EEPROM Check
Data write → read, and accord check
Error 03: EEPROM write/read discord
Data 0x9249, 0x2942, 0x4294 are written to addresses
0x00~0xFF of EEPROM (IC101), then read and checked.
Before writing, the data are saved, then after checking, they
are written to restore the contents of EEPROM.
4.
Servo
(4-2) Servo DSP Check
Data write → read, and accord check
Error 12: Read data discord
Data 0x9249, 0x2942, 0x4294 are written to the address
0x602 of RAM in the Servo DSP (IC302), then read and
checked.
(4-3) DSP Driver Test
Test signal data → DSP Driver
Error: Not detected.
Caution: Do not conduct this test with a mechanical deck
connected.
The maximum voltage is applied to the Servo Driver IC
(IC401). If mechanical deck is connected, the motor and
optics could be damaged. Disconnect mechanical deck following the output message, then enter specified 4- or 5digit number from the remote commander, and press the
[ENTER]. The test is conducted only when the input data
accord. Check the output level, then press the > to finish the test.
This test is skipped if “All” is selected.
Supplement: How to disconnect mechanical deck
Disconnect flat cables connected to the CN010 and CN015
of MB board. Also, disconnect harness from the CN203.
13
DVP-S9
Ver 1.6
5. Supply
Caution: Do not conduct this check with a mechanical deck connected.
An access is made to the stream supply and servo control
IC (IC302) and external RAM (IC303) using check data.
If mechanical deck is connected, the motor and optics
could be damaged. This check is also executed by the
“All” menu item.
Supplement: How to disconnect mechanical deck
Disconnect flat cables connected to the CN010 and
CN015 of MB board. Also, disconnect harness from
the CN203.
(5-2) ARP Register Check
Data write → read, and accord check
Error 08: ARP register write, and read data discord
Data 0x00 to 0xFF are written to the TMAX register (address 0xC6) in ARP (IC302), then they are read and checked.
(5-3) ARP to RAM Data Bus
Data write → read, and accord check
Error 09: ARP ←→ RAM data bus error
Data 0x0001 to 0x8000 where one bit each is set to 1 are
written to the address 0 of RAM (IC303) connected to the
ARP (IC302) through the bus, then they are read and
checked. In case of discord, written bit pattern and read
data are displayed. If data where multiple bits are 1 are
read, the bits concerned may touch each other. Further, if
data where certain bit is always 1 or 0 regardless of written
data, the line could be disconnected or shorted.
(5-4) ARP to RAM Address Bus
Data write → other address read discord check
Error 10: ARP → RAM address bus error
Caution: Address and data display in case of an error is
different from the display of other diagnosis (described later).
Before starting the test, all addresses of RAM (IC303) are
cleared to 0x0000.
First, 0xA55A is written to the address 0x00000, and the
address data are read and checked from addresses 0x00001
to 0x80000 while shifting 1 bit each. Next, the data at that
address is cleared, and it is written to the address 0x00001,
and read and checked in the same manner. This check is
repeated up to the address 0x80000 while shifting the address data by 1 bit each.
If data other than 0 is read at the addresses except written
address, an error is given because all addresses were already cleared to 0. In this check, the error display pattern is
different from that of other diagnosis; read data, written
address, and read address are displayed in this order. However, the message uses same template, and accordingly exchange Address and Data when reading. The following display, for example,
### Syscon Diagnosis ###
5-4. ARP to RAM Address Bus
Error 10: ARP - RAM Address B
Address
: 0000A55A
Write Data : 00000000
Read Data : 00080000
Press NEXT Key to Continue
Press PREV Key to Repeat
_
shows the data 0xA55A was read from address 0x00080000
though it was written to the address 0x00000000. This implies that these addresses are in the form of shadow. Also,
if the read data is not 0xA55A, another error will be present.
(5-5) ARP RAM Check
Data write → read, and accord check
Error 11: ARP RAM read data discord
The program code data stored in ROM are copied to all
areas of RAM (IC303) connected to the ARP (IC302)
through the bus, then they are read and checked if they accord. If the detail check was selected initially, the data are
written to all areas and read, then the same test is conducted
once again with the data where all bits are inverted between
1 and 0. If discord is detected, faulty address, written data,
and read data are displayed following the error code 11,
and the test is suspended.
14
DVP-S9
Ver 1.6
6.
AV Decoder
(6-2) 1930 RAM
Data write → read, and accord check
Error 13: AVD RAM read data discord
The program code data stored in ROM (IC107) are copied
to all areas oo»RAM (IC504, IC505) connected to the AVD
(IC503) through the bus, then they are read and checked if
they accord. Further, the same test is conducted once again
with the data where all bits are inverted between 1 and 0. If
discord is detected, faulty address, written data, and read
data are displayed following the error code 13, and the test
is suspended.
Check Items List
2) Version
(2-2) Revision
(2-3) ROM Check Sum
(2-4) Model Type
(2-5) Region
3) Peripheral
(3-2) EEPROM Check
4) Servo
(4-2) Servo DSP Check
(4-3) DSP Driver Test
(6-3) 1930 SP
ROM → AVD RAM → Video OUT
Error: Not detected.
The data including sub picture streams in ROM (IC107)
are transferred to the RAM (IC504, IC505) in AVD (IC503),
and output as video signals from the AVD (IC503).
They are output from all video terminals (Composite, Y/C).
5) Supply
(5-2) ARP Register Check
(5-3) ARP to RAM Data Bus
(5-4) ARP to RAM Address Bus
(5-5) ARP RAM Check
7.
6) AV Decoder
(6-2) 1930 RAM
(6-3) 1930 SP
Video
(7-2) Color Bar
AVD color bar command write → Video OUT
Error: Not detected.
The command is transferred to the AVD, and the color bar
signals are output from video terminals.
They are output from all video terminals (Composite, Y/C).
(7-3) Composit Out
(7-4) Y/C Out
(7-6) Component Out
8.
Audio
(8-2) ARP → 1930
Error 14
: ARP → 1930 video NG
15
: ARP → 1930 audio NG
(8-3) Test Tone
All channels
2ch Left
2ch Right
Front Left
Front Right
Rear Left
Rear Right
Center
Sub Woofer
7) Video
(7-2) Color Bar
(7-3) Composit Out
(7-4) Y/C Out
(7-6) Component Out
8) Audio
(8-2) ARP → 1930
(8-3) Test Tone
Error Codes List
00: Error not detected
01: RAM write/read data discord
02: Gate array NG
03: EEPROM NG
08: ARP register read data discord
09: ARP ←→ RAM data bus error
10: ARP ←→ RAM address bus error
11: ARP RAM read data discord
12: Servo DSP NG
13: 1930 SDRAM NG
14: ARP → 1930 video NG
15: ARP → 1930 audio NG
16: 1910 UCODE download NG
17: System call error (function not supported)
18: System call error (parameter error)
19: System call error (illegal ID number)
20: System call error (time out)
90: Error occurred
91: User verification NG
92: Diagnosis cancelled
15
DVP-S9
Ver 1.6
[DRIVE AUTO ADJUSTMENT]
1.
DVD-SL (single layer)
On the Test Mode Menu screen, press [1] key on the remote commander, and the drive auto adjustment menu will be displayed.
Select [1], insert DVD single layer disc, and press [ENTER] key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
## Drive Auto Adjustment ##
Adjustment Menu
0.
1.
2.
3.
ALL
DVD-SL
CD
DVD-DL
Exit: RETURN
Normally, [10/0] is selected to adjust DVD (single layer), CD and
DVD (dual layer). But, individual items can be adjusted for the
case where adjustment is suspended due to an error. In this mode,
the adjustment can be made easily through the operation following the message displayed on the screen.
The disc used for adjustment must be the one specified for adjustment.
0.
ALL
Select [10/0] and press [ENTER] key, and the servo set data in
EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD disc
and 3. DVD-DL disc are adjusted in this order. Each time one disc
was adjusted, it is ejected. Replace it with the specified disc following the message. You can finish the adjustment if pressing
the x button. During adjustment of each disc, the measurement
for disc type judgment is made. As automatic adjustment does not
judge the disc type unlike conventional models, take care not to
insert wrong type discs. Also, do not give a shock during adjustment.
16
DVD Single Layer Disc Adjustment Steps
1. SLED TILT Reset
2. Disc Check Memory SL
3. Wait 300 msec
4. Set Disc Type SL
5. LD ON
6. Spdl Start
7. Wait 1 sec
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. CLVA ON
11. Wait 500 msec
12. Tracking ON
13. Wait 1 sec
14. Sled ON
15. Check CLV Lock
16. Auto LFO Adjust
17. Auto Focus Offset Adjust
18. Auto Tilt Position Adjust
19. Auto Focus Gain Adjust
20. Auto Focus Offset Adjust
21. EQ Boost Adjust
22. Auto LFO Adjust
23. Auto Track Gain Adjust, Search Check
24. 32Tj Fwd
25. 32Tj Rev
26. 500Tj Fwd
27. 500Tj Rev
28. All Servo Stop
29. Eep Copy Loop Filter Offset
DVP-S9
Ver 1.6
2.
CD
3.
DVD-DL (dual layer)
Select [2], insert CD disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM.
Select [3], insert DVD dual layer disc, and press [ENTER] key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM.
CD Adjustment Steps
1. Sled Tilt Rest
2. Disc Check Memory CD
3. Wait 500 msec
4. Set Disc Type CD
5. LD ON
6. Spdl Start
7. Wait 500 msec
8. Focus Servo ON 0
9. Auto Track Offset Adjust
DVD Dual Layer Disc Adjustment Steps
1. Sled Tilt Reset
2. Disc Check Memory DL
3. Wait 500 msec
4. Set Disc Type DL
5. LD ON
6. Spdl Start
7. Wait 1 sec, Layer 1 Adjust
8. Focus Servo ON 0
9. Auto Track Offset Adjust
10. CLVA ON
11. Wait 500 msec
12. Tracking ON
13. (TC Display Start)
14. Wait 1 sec
15. Jitter Display Start
16. Sled ON
17. Check CLV ON
18. Auto LFO Adjust
19. Auto Focus Offset Adjust
20.
21. Auto Focus Gain Adjust
22. Auto Focus Offset Adjust
23. Eq Boost Adjust
24. Auto LFO Adjust
25. Auto Track Gain Adjust, Search Check
26. 32Tj Fwd
27. 32Tj Rev
28. 500Tj Fwd
29. 500Tj Rev
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
Clva ON
Wait 500 msec
Tracking ON
Wait 500 msec
Sled ON
Check CLV Lock
Auto Loop Filter Offset Auto Focus Adjust
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
Clva ON
Wait 500 msec
Tracking ON
Wait 500 msec
Sled ON
Check CLV Lock
Auto Focus Filter Offset
Auto Focus Adjust
30. All Servo Stop
Auto Focus Gain Adjust
Auto Focus Offset Adjust
Eq Boost Adjust
Auto Loop Filter Offset
Auto Track Gain Adjust, Search Check
32Tj Fwd
32Tj Rev
500Tj Fwd
500Tj Rev, Layer 0 Adjust
Fj (L1 -> L0)
Auto Track Offset Adjust L0
Auto Focus Gain Adjust
Auto Focus Offset Adjust
Eq Boost Adjust
Auto Loop Filter Offset
Auto Track Gain Adjust, Search Check
32Tj Fwd
32Tj Rev
500Tj fwd
500Tj Rev, Layer Jump Check
Lj (L0 -> L1)
Lj (L1 -> L0)
49. All Servo Stop
17
DVP-S9
Ver 1.6
[DRIVE MANUAL OPERATION]
0.
Disc Check
On the Test Mode Menu screen, select [2], and the manual operation menu will be displayed. For the manual operation, each servo
on/off control and adjustment can be executed manually.
## Drive Manual Operation ##
1.
2.
3.
4.
5.
6.
7.
Operation Menu
Disc type
Servo Control
Track/Layer Jump
Manual Adjustment
Auto Adjustment
Memory Check
Sacd Water Mark
0. Disc Check Memory
_
Exit: Return
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is displayed when a disc is loaded.
1. Set correctly the disc type to be used on the Disc Type
screen.
The disc type must be set after a disc was loaded.
The set disc type is cleared when the tray is opened.
2. After power ON, if the Drive Manual Operation was selected, first perform “Reset SLED TILT” by opening 1.
Disc Type screen.
3. In case of an alarm, immediately press the x button to
stop the servo operation, and turn the power OFF.
Basic operation (controllable from front panel or remote commander)
I/1
x
Z
[RETURN]
> , .
[1] to [9], [10/0]
Cursor ↑ / ↓
18
Power OFF
Servo stop
Stop+Eject/Loading
Return to Operation Menu or Test Mode
Menu
Transition between sub modes of menu
Selection of menu items
Increase/Decrease in manually adjusted
value
Disc Check Memory
1. SL Disc Check
2. CD Disc Check
3. DL Disc Check
0. Reset SLED TILT
_
On this screen, the mirror time is measured to judge the disc and it
is written to the EEPROM. First load DVD SL disc and press [1],
next load CD disc and press [2], and finally load DVD DL disc
and press [3].
The adjustment must be executed more than once after default
data were written. External vibration or shock to the player must
not be given. Reference value for DVD is from 10 to 20, and for
CD, from 28 to 4F.
Check that the value of CD is larger than that of DVD.
When those values are beyond a range perform this adjustment
again.
From this screen, you can go to another mode by
pressing > or . key, but you cannot enter this mode from
another mode. You can enter this mode from the Operation Menu
screen only.
1.
Disc Type
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
-- SA. ------ SI. -EMG. 00
DVD SL12cm
On this screen, select the disc type. To select the disc type, press
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting [1] automatically selects and displays the
disc type. In case of wrong display, retry “Disc Check Memory”.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
DVP-S9
Ver 1.6
Disc Type
1. Disc Type Auto Check
2. DVD SL
12 cm
3. DVD DL
12 cm
4. CD
12cm
5. LCD
12 cm
6. DVD SL
8 cm
7. DVD DL
8 cm
8. CD
8 cm
9. LCD
8 cm
0. Reset SLED TILT
SA.
SI.
EMG. 00
DVD SL 12 cm
Display when DVD SL 12cm disc was selected
1.
2.
3.
4.
5.
6.
7.
8.
9.
0.
Disc Type
Disc Type Auto Check
DVD SL
12 cm
DVD DL
12 cm
CD
12cm
LCD
12 cm
DVD SL
8 cm
DVD DL
8 cm
CD
8 cm
LCD
8 cm
Reset SLED TILT
TC.
:
:
EMG. 00
12 cm
2. Servo Control
1.
2.
3.
4.
5.
6.
7.
Servo Control
LD
Off R.Sled FWD
SP
Off L.Sled REV
Focus
Off
TRK.
Off
Sled
Off
CLVA
Off
FCS. Srch Off
0. Reset SLED TILT
SA.
SI.
DVD SL 12 cm
EMG. 00
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
[10/0]
Reset SLED TILT
Reset the Sled
and Tilt to initial position.
[1] LD
Turn ON/OFF the laser.
Display when CD 12cm disc was selected
[2] SP
Turn ON/OFF the spindle.
[0] Reset SLED TILT
Reset the Sled and Tilt to initial position.
[3] Focus
Search the focus and turn on the focus.
[4] TRK
Turn ON/OFF the tracking servo.
[1] Disk Type Check
Judge automatically the loaded disc. As
the judged result is displayed at the bottom of screen, make sure that it is correct.
If Disc Check Memory menu has not
been executed after EEPROM default
setting, the disc type cannot be judged.
In this case, return to the initial menu
and make a check for three types of
discs (SL, DL, CD).
[5] Sled
Turn ON/OFF the sled servo.
[6] CLVA
Turn ON/OFF normal servo of spindle
servo.
[7] FCS. Srch
Apply same voltage as that of focus
search to the focus drive to check the
focus drive system.
→ Sled FWD
Move the sled outward. Perform this
operation with the tracking servo turned
off.
← Sled REV
Move the sled inward. Perform this operation with the tracking servo turned
off.
↑ Tilt UP
Move the tilt upward.
↓ Tilt DOWN
Move the tilt downward.
CD
[2] to [9]
Select the loaded disc. The adjusted
value is written to the address of selected disc. No further entry is necessary if [1] was selected.
The following menus are normally not used.
3.
Track/Layer Jump
4.
Manual Adjustment
5.
Auto Adjustment
The persons who do not know well about these menus should not
use them.
19
DVP-S9
Ver 1.6
6. Memory Check
[EMERGENCY HISTORY]
EEPROM Data1
### EMG. History ###
-– DL –LCD SL L0
xx
xx xx
xx
xx xx
xx
xx xx
xx
xx xx
xx
xx xx
xx
xx xx
xx
xx xx
xx
xx xx
CD
Focus Gain
xx
TRK. Gain
xx
FCS Balance
xx
Focus Bias
xx
TRV. Offset
xx
L. F. Offset xx
EQ Boost
xx
Mirror Time
xx
_DOWN: Next Data
CLEAR: Default Set
L1
xx
xx
xx
xx
xx
xx
xx
xx
page.1/2
EEPROM Data1
-– DL –LCD SL L0
-xx xx
-xx --xx --xx --xx -xx
xx xx
xx
xx xx
CD
RF Jitter
xx
RF Level
xx
FE Level
xx
FE Balance
xx
TRV. Level
xx
Analog FRSW
xx
PLL DacGain
xx
_
UP : Prev Data
CLEAR: Default Set
L1
xx
----xx
xx
page.2/2
This screen displays current servo adjusted data stored in the
EEPROM. Though adjusted data can be initialized with the
[CLEAR] key, they cannot be restored after initialization.
So, before clearing, make a note of the adjusted data.
For reference, the drive has been designed so that the gain center
value is 20 and offset value is 80. Other values will be in a range
of 10 to 80. If extreme value such as 00 or FF is set, adjustment
will be faulty. In such a case, check for disc scratch or cable disconnection, then perform adjustment again.
Laser Hours
CD
DVD
xxxxxxxh
xxxxxxxh
1. 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
2. 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
Select: 1 – 9 Scroll: UP/DOWN
(1: Last EMG.) Exit: RETURN
On the Test Mode Menu screen, selecting [4] displays the information such as servo emergency history. The history information
from last 1 up to 10 can be scrolled with ↑ key or ↓ key. Also,
specific information can be displayed by directly entering that
number with ten keys.
The upper two lines display the laser ON total hours. Data below
minutes are omitted.
Clearing History Information
Clearing laser hours
Press [DVD DISPLAY] and [CLEAR] keys in this order.
Both CD and DVD data are cleared.
Clearing emergency history
Press [TITLE] and [CLEAR] keys in this order.
Initializing set up data
Press [DVD SET UP] and [CLEAR] keys in this order.
The data have been initialized when “Set Up Initialized” message is displayed. The EMG. History screen will be restored
soon.
How to see Emergency History
[MECHA AGING]
### Mecha Aging ###
3
1
2
1.
2
Press OPEN Key
Abort: STOP key
On the Test Mode Menu Screen, selecting [3] executes the aging
of the mechanism. Start aging with PLAY. During aging, the repeat cycle is displayed. Aging can be aborted at any time by pressing the x key. After the operation is stopped, press the x key
or [RETURN] key again to return to the Test Mode Menu.
SEARCH Aging is only for a CD.
20
1 : Emergency Code
2 : Don’t Care
These codes are used for verification of software designing.
3 : Historical order 1 to 9
DVP-S9
Ver 1.6
Emergency Codes List
10: Communication to IC001 (RF board) failed.
11: Each servo for focus, tracking, and spindle is unlocked.
12: Communication to EEPROM, IC101 (MB board) failed.
13: Writing of hours meter data to EEPROM, IC101 (MB board)
failed.
14: Communication to Servo DSP IC302 (MB board) failed, or
Servo DSP is faulty.
20: Initialization of tilt servo and sled servo failed. They are not
placed in the initial position.
21: Tilt servo operation error
22: Syscon made a request to move the tilt servo to wrong position.
23: Sled servo operation error
24: Syscon made a request to move the sled servo to wrong position.
30: Tracking balance adjustment error
31: Tracking gain adjustment error
32: Focus balance adjustment error
33: Focus bias adjustment error
34: Focus gain adjustment error
35: Tilt servo adjustment error
36: RF equalizer adjustment error
37: RF group delay adjustment error
38: Jitter value after adaptive servo operation is too large.
40: Focus servo does not operate.
41: With a dual layer (DL) disc, focus jump failed.50: CLV
(spindle) servo does not operate.
51: Spindle does not stop.
60: With a DVD disc, Syscon made a request to seek nonexistent
address.
61: With a CD disc, Syscon made a request to seek nonexistent
address.
62: With a CD disc, Syscon made a request to seek nonexistent
track No. and index No.
63: With a DVD disc, seeking of target address failed.
64: With a CD disc, seeking of target address failed.
65: With a CD disc, seeking of target index failed.
70: With a DVD disc, physical information data could not be read.
71: With a CD disc, TOC data could not be read.
80: Disc type judgment failed.
81: As disc type judgment failed, retry was repeated.
82: As disc type judgment failed, a measurement error occurred.
83: Disc type could not be judged within the specified time.
84: Illegal command code was received from Syscon.
85: Illegal command was received from Syscon.
[VIDEO LEVEL ADJUSTMENT]
On the Test Mode Menu screen, selecting [6] displays color bars
for video level adjustment. During display of color bars, OSD disappears but the menu screen will be restored if pressing any key.
Measurement point
: VIDEO OUT jack
(75 Ω terminating resistance)
Measuring instrument : Oscilloscope
Adjustment device : RV501 on MB board
+ 0.04
Specified value
: 1.0 – 0.02 Vpp
0.04
1.0 +– 0.02
Vp-p
[VERSION INFORMATION]
## Version Information ##
IF con.
Ver: x. xxx (xxxx)
Group
00
SYScon.
Ver: x. xxx (xxxx)
Model
xx
Region
0x
Servo DSP Ver:X.XXX
OPT Type:2 Laser
Exit: RETURN
On the Test Mode Menu screen, selecting [5] displays the ROM
version and region code.
The parenthesized hexadecimal number in version field is
checksum value of ROM.
21
DVP-S9
Ver 1.6
SECTION 5
ELECTRICAL ADJUSTMENTS
Note: During diagnostic check, the characters and color bars can be seen
only with the NTSC monitor. Therefore, for diagnostic check, use
the monitor that supports both NTSC and PAL modes
Instruments required:
1) Color monitor TV
2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz,
with delay mode
3) DVD reference disc
HLX-501 (J-6090-071-A) (dual layer) (NTSC)
HLX-503 (J-6090-069-A) (single layer) (NTSC)
HLX-504 (J-6090-088-A) (single layer) (NTSC)
HLX-505 (J-6090-089-A) (dual layer) (NTSC)
HLX-506 (J-6090-077-A) (single layer) (PAL)
HLX-507 (J-6090-078-A) (dual layer) (PAL)
AUTO SERVO ADJUSTMENT
After parts related to the servo circuit (RF amplifier (IC001), DSP
(IC302), motor driver (IC401), EEPROM (IC101) so on) are replaced, re-adjusting the servo circuit is necessary. Select “ALL” at
“DRIVE AUTO ADJUSTMENT” (Refer to page 16 in TEST
MODE) and adjust DVD-SL (single layer), CD and DVD-DL (dual
layer).
VIDEO LEVEL ADJUSTMENT
<Purpose>
This adjustment is made to satisfy the NTSC/PAL standard, and if
not adjusted correctly, the brightness will be too large or small.
Signal
Color bars
Test point
VIDEO OUT jack
(75 Ω terminated)
Instrument
Oscilloscope
Adjusting element
RV501 (MB board)
Specified Value
1.0
+ 0.04
– 0.02
Procedure:
1. Press the I/1 button to turn the power on, and turn the
[FUNCTION] knob to select “DVD” of A/V amplifier (TAS9D).
2. Confirm that the S-Y level is 1.0 ± 0.05 Vp-p.
1.0 ± 0.05 Vp-p
Figure 5-2
CHECKING S VIDEO OUTPUT S-C
<Purpose>
This checks whether the S-C satisfies the NTSC Standard. If it is
not correct, the colors will be too dark or light.
Signal
Color bars
Test point
S VIDEO OUT (S-C) jack
(75 Ω terminated)
Instrument
Oscilloscope
Specified Value
286 ± 30 mVp-p (NTSC)
300 ± 100 mVp-p (PAL)
Procedure:
1. Press the I/1 button to turn the power on, and turn the
[FUNCTION] knob to select “DVD” of A/V amplifier (TAS9D).
2. Confirm that the S-C burst is 286 ± 30 mVp-p (NTSC) or 300
± 100 mVp-p (PAL).
286 ± 50 mVp-p
(NTSC)
or
300 ± 100 mVp-p
(PAL)
Vp-p
Procedure:
1. Press the I/1 button to turn the power on, and turn the
[FUNCTION] knob to select “DVD” of A/V amplifier (TAS9D).
+ 0.04
2. Adjust the RV501 on the MB board to attain 1.0 – 0.02 Vp-p.
Figure 5-3
Adjustment Location :
– MB Board (Component Side) –
1.0
+ 0.04
– 0.02
Vp-p
IC202
IC103
Figure 5-1
CHECKING S VIDEO OUTPUT S-Y
<Purpose>
Check S-terminal video output. If it is incorrect, pictures will not
be displayed correctly in spite of connection to the TV with a Sterminal cable.
Signal
Color bars
Test point
S VIDEO OUT (S-Y) jack
(75 Ω terminated)
Instrument
Oscilloscope
Specified Value
1.0 ± 0.05 Vp-p
22
IC503
IC302
RV501
Video
Level
Adjustment
DVP-S9
Ver 1.5
SECTION 6
DIAGRAMS
6-1.
BLOCK DIAGRAM – RF/SERVO Section – • Refer to servicing notes (page 4) for discrimination of TYPE A/B.
OPTICAL PICK-UP
BLOCK
(KHM-240AAA) (TYPE A)
(KHM-270AAA) (TYPE B)
RF
ATOP 64
ATON 63
2 RF IN
61 AIP
62 AIN
FNP 55
FNN 54
56 DIP
57 DIN
RF+
SIGO 59
A
(Page 24)
A
B
C
D
DVD/CD
DETECTOR
E
F
G
H
VC
DVD/CD
LASER
DIODE
MODULE
A
B
C
D
7
8
9
10
A2
B2
C2
D2
15
16
17
18
19
E
F
G
H
VC
DVD LD
AUTOMATIC POWER
CONTROL (FOR DVD)
Q001
25 DVDLD
CD LD
AUTOMATIC POWER
CONTROL (FOR CD)
Q002
26 CDLD
FE
TE
TZIN
PI
PII
DVD/CD RF AMP,
FOCUS/TRACKING ERROR AMP
IC001
42
41
40
36
35
136 ADC1
135 ADC0
MIRR 33
TZC 37
197 MIRR
196 TZC
SRD
SWD
SCLK
SDEN
173
174
175
180
45
46
47
48
SW
GIO6/SDI
GIO7/SDO
GIO8/SCK
GIO13
184 ADC7
172 GIO5/PGIN
XLDON
LDON 27
INLIM
166 GIO0/INT2
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC401
42
SERVO DIGITAL
SIGNAL PROCESSOR
IC302 (1/2)
40
2-AXIS
DEVICE
TRACKING
COIL
FCS+
FCS–
TRK+
TRK–
: CD PLAY
VCI 39
24 LDSELO
D+3.3V
FOCUS
COIL
: DVD PLAY
185 DFCTI
MON 44
21 DVDPD
22 CDPD
• SIGNAL PATH
137 ADC2
DFT 38
PD
INLIMIT
SENSOR
14
13
12
11
37
36
FOCUS COIL
DRIVE
48
1
204 PDM2
205 PDM3
35
34
TRACKING COIL
DRIVE
3
4
202 PDM0
203 PDM1
19
46
47
M
SPM+
SPM–
27
28
–
+
SPINDLE MOTOR
DRIVE
5
139 ADC3
45
140 ADC4
13
159 MDSO
161 MDPO
21
167 GIO1/INT3
7
10
198 PWM0
199 PWM1
(SPINDLE)
M
(SLED)
SLA+
SLA–
SLB+
SLB–
32
31
30
29
SLED MOTOR
DRIVE
HINT 22
HCS 24
XDSPRST 156
XSDPIT
XSDPCS
XRST
C
(Page 24)
20
TSD-M
22
POWER SAVE
39
7 GIO2/INT4
168
XDRVMUTE
XLDON
XSDPIT, XSDPCS,
XDRVMUTE
B
(Page 25)
23
23
DVP-S9
6-2.
BLOCK DIAGRAM – MAIN Section (1/2) –
CLK
CKE
DQML
DQMU
WE
CAS
RAS
CS
CLK
CKE
DQML
DQMU
WE
CAS
RAS
CLK
CKE
DQML
DQMU
WE
CAS
RAS
CS
CLK
CKE
DQML
DQMU
WE
CAS
RAS
220 221
224 231
28 11
A0 – A20
25, 24 – 18,
8 – 1, 48, 17,
16, 9, 10
ADDRESS BUS
ADDRESS BUS
XRD
XWRH
67 62 17
35
16
61 60
47 46 50 49
85 – 100
HD0 – HD15
: CD PLAY
: DVD/CD PLAY (VIDEO)
: DVD/CD PLAY (AUDIO)
102 – 109, 111 – 118,
120, 1 – 5
HA0 – HA21
58
EEPROM
IC101
SYSTEM CONTROLLER
IC103 (1/2)
SDA 38
SCL 39
WP 7
24
24
SDCS1B
: DVD PLAY
: DVD/CD PLAY (DIGITAL OUT)
XRST
70 71
• SIGNAL PATH
26
HA0 – HA21
DATA BUS
36
SDCLKO
SDCKEO
SDDQM0
SDDQM1
SDWEOB
SDCKCOB
SDRASOB
CLK
CKE
DQML
DQMU
WE
CAS
RAS
DQ0 – DQ15
31, 33, 35, 38, 40, 42,
44, 30, 32, 34, 36, 39, 41,
43, 45
HD0 – HD15
DATA BUS
XRST
143
FLASH MEMORY
IC107
HD0 – HD15
HA0 – HA3, HA19
149 146 155 154 152 151 147
226 227 228 229
DACK0
DREQ0
DACK1
DREQ1
C
HAD0 – HAD21
218 – 215, 213 – 210, 208 – 205,
203 – 200, 198 – 195, 193, 192
DACK0
DREQ0
DACK1
DREQ1
(Page 23)
HD8 – HD11
XRD, XWRH
144
INT0
I
SDAD0 – SDAD11
HD0 – HD15
HIREQ0 223
XRST
(Page 25)
SDDQ0 – SDDQ15
223 – 235, 237 – 240,
2 – 5, 7 – 10
HAD23 190
HAD22 191
XWAIT
CS4X
INT1
H
CRPCLKI
CLKI
SCLKI
ACLK
XWRH 207
XRD 208
A0 – A7
11 – 15, 17 – 19
134, 131, 128, 125, 124,
127, 130, 133, 136, 139,
137, 140
AV DECODER
IC503
XRD
XWRH
(Page 25)
TDI
TDO
TCK
TMS
TRST
177, 174, 171, 168, 165, 163,
160, 158, 157, 159, 162, 164,
167, 170, 173, 176
HA0 – HA7
HD8 – HD15
G
29
180
182
512FSAVD
12
(Page 25)
SDRAM ADDRESS BUS
DO 20
OE
WE
33MAVD
27MAVD
35 34 14 36 15 16 17 18
K
SDRAM DATA BUS
(FOR JTAG)
XINT 21
XCS 23
XWAT 25
21 – 24, 27 – 32,
20, 19
CE
118
119
120
121
122
A0 – A11
2, 3, 5, 6, 8, 9, 11, 12, 39,
40, 42, 43, 45, 46, 48 ,49
CS0X
195
193
194
192
191
CDIN1I
CDBCKI
CDLRKI
CDIN2I
DQ0 – DQ15
35 34 14 36 15 16 17 18
HA1 – HA21
23
25
26
22
XARPRST
(Page 25)
A0 – A11
21 – 24, 27 – 32,
20, 19
SDCS0B
62
63
65
66
TRST
D0 – D7
2–9
DQ0 – DQ15
2, 3, 5, 6, 8, 9, 11, 12, 39,
40, 42, 43, 45, 46, 48 ,49
(Page 25)
DM ACK1
DM REQ1
DM ACK0
DM REQ0
TDO
TDI
TCK
TMS
TRST
157 XARPRST
F
RV501
16MB SDRAM
IC505
J
DACK0
DREQ0
DACK1
DREQ1
44 – 51, 53 – 60
MD0 –MD15
DATA
BCLK
LRCK
DOUT
(Page 25)
(Page 25)
VREFI 84
CS3X
CS2X
E
16MB SDRAM
IC504
VIDEO
LEVEL
182 CLKIN
187 MCKI
189 SCKI
(Page 25)
ICLKI
ISTARTI
IREQO
IVALI
IERRI
HA0 – HA21
33MARP
XMWR
XOE
XRAS
XCAS
41
44
46
45
43
HD0 – HD15
33MARP, 33MAVD,
27MAVD, 512FSAVD
38
42
41
39
68
69
70
71
72
SPDIF
HWAITOB
RSTB
17
33
18
34
35
MEMA0 –
MEMA9
SDCK
XSHD
XSRQ
XSAK
SDEF
V, Y, C
V
Y
C
COMPOUT 80
YOUT 74
COUT 7
HCSB
HRWB
WE
OE
RAS
UCAS
LCAS
MEMD0 –
MEMD15
27 – 36
A0 – A9
I/O0 – I/O15
D
21 – 24,
27 – 32
D-RAM
IC303
2 – 5, 7 – 10,
41 – 44, 46 – 49
128 RFIN2
DTI0 – DTI7
(Page 23)
SOI0 –SOI7
31 – 34, 36 – 39
131 RFIN1
SD0 – SD7
RF+
MA0 – MA9
A
73 – 76, 78 – 81
ARP
IC302 (2/2)
5 SDA
6 SCL
7 WP
DVP-S9
6-3.
BLOCK DIAGRAM – MAIN Section (2/2) –
VIDEO BUFFER
IC701
V
7 INC
Y
J
V, Y, C
OUTC1
OUTC2
OUTB1
OUTB2
OUTA1
OUTA2
4 INB
C
2 INA
(Page 24)
J202
10
9
13
12
15
14
VIDEO OUT
2
1
OPTICAL
TRANSMITTER
IC201
SPDIF
D+5V
B+
(Page 24)
S VIDEO OUT
4
MUTE
1
K
J201
3
VIDEO SWITCH
Q711, 712
OPTICAL
OUT
TO ST-S9
WIDE 82
CLOCK GENERATOR
IC102
8 XTO
SYSTEM CONTROLLER
IC103 (2/2)
X101
16.5MHz
X102
27MHz
7 XTI
53 X1
14 FSEL
48/44.1k 81
33-2OUT 13
27-1OUT 3
512-1OUT 10
33MARP, 33MAVD,
27MAVD, 512FSAVD
IC106 (1/3)
1
3
2
25
27
51
20
83
76
IFSO0, IFSI0, IFSC0, XIFCS,
XIFINT, XIFOK, XFRRST
IFSO0
IFSI0
4
5
IFSC0
6
IC106 (2/3)
XIFINT
XIFOK
XFRRST
12
13
11
XIFCS
IC106 (3/3)
TRST
• SIGNAL PATH
: DVD/CD PLAY (VIDEO)
CN103
SI2 31
2 RXD
: DVD/CD PLAY (DIGITAL OUT)
XLDON
INT2
CS5X
XDRVMUTE
CPUCK 77
CS6X 65
INT3 19
8 CK
48 CS5
12 INT
HD8 – HD11
DATA BUS
(Page 24)
G
HA0 – HA3, HA19
HA0 – HA3,
HA19
ADDRESS BUS
(Page 24)
H
XRD, XWRH
(Page 24)
I
XRST
(Page 24)
XRD
XWRH
18 – 15
84
18
63
48
5–1
HD8 – HD11
XSDPIT
XSDPCS
XDRVMUTE
GATE ARRAY
IC202
SHA0 – SHA3. D0 – D3
SHA19
XLDON, XSDPIT, XSDPCS
XDRVMUTE
XLDON
11 RDN
10 WRN
9 XRST
TRMP 33
TRMM 32
LOADING MOTOR
DRIVE
IC701
SUB TRAY1 – 3
HEIGHT SENSOR
IC731 – 733
36 – 34
1 TXD
TSW1 – TSW3
SO2 32
(FOR TEST)
F
M
(Page 26)
(Page 24)
B
D
(Page 24)
SI0
SC0
XIFCS
INT4
MAMUTE
XFRST
(Page 23)
L
(Page 26)
33MAVD
27MAVD
512FSAVD
54 X0
SO0 26
E
VMUTE
33MARP
33-1OUT 15
M
M721
(LOADING)
CKMM 28
S741
(IN)
CKMP 29
S742 ON: WHEN SUB TRAY IS
(OUT)
CHUCKING POSITION
DSW1 27
Q701
ON: WHEN SUB TRAY SLIDES OUT
OF THE CHUCKING POSITION
DISC IN
DETECT
IC751
25
25
DVP-S9
6-4.
BLOCK DIAGRAM – INTERFACE CONTROL Section –
CN103
M
IFSO0, IFSI0, IFSC0,
XVIFCS, XIFINT, XIFOK,
XFRRST
(Page 25)
IFSO0
IFSI0
IFSC0
XVIFCS
XIFINT
XIFOK
XFRRST
36
35
37
19
42
43
40
SYS DATAIN
SYS DATAOUT
SYS CLK
SYS CS
SYS RQ
SYS OK
SYS RST
EXP-OUT DATA
EXP-IN DATA
EXP-CLK
EXP-LAT
KEY2
A-TRIG
B-TRIG
REC/PB/PAS
A-SHUT
B-SHUT
B-HALF
85
84
87
86
94
55
53
59
89
90
91
10
9
8
7
6
4
5
11
12
13
14
3
DATA-OUT
DATA-IN
CLK
LAT
KEY2
ATRIG
BTRIG
REC/PB/PAS
ASHUT
BSHUT
BHALF
UNREG
SYSTEM CONTROL 5
FROM TC-S9
CN102
7
UNREG (TC)
CN101
IIC DATA 30
IIC CLK 29
RESET 12
L
VMUTE
(Page 25)
VMUTE 48
D+5V (LED)
B+
EVER+5V
INTERFACE CONTROLLER (IC401) B+
INTERFACE CONTROLLER
IC401
S701 – 708
97 KEY0
S711 – 720
65 – 83, 88
D701 – 705
LED DISC1
ı
LED DISC3
LED PLAY
LED PAUSE
3
V-MUTE
8
9
AC
AC
5
EVER+5V
+5V REGULATOR
IC502
RECT
D501 – 504
D+5V
RF SECTION,
GATE ARRAY (IC202), MOTOR/COIL DRIVE (IC401),
SERVO DSP (IC503), VIDEO BUFFER (IC701) B+
POWER BLOCK
+5V
+3.3V
SERVO DSP (IC302) B+
+3.3V REGULATOR
IC301
+3.3V
AV DECODER (IC503) B+
+3.3V REGULATOR
IC502
+3.3V
+1.8V
SERVO DSP (IC302),
AV DECODER (IC503) B+
+1.8V REGULATOR
IC006
+1.8V
AV DECODER (IC503) B+
+1.8V REGULATOR
IC501
M+12V
+7V REGULATOR
IC501
+12V
P. CONT
15 X-IN
P-CONT 44
26
SYSTEM CONTROL 3
FROM ST-S9
D512
M+7V
MOTOR DRIVE (IC701) B+
X401
16MHz
26
D513
M+12V
MOTOR/COIL DRIVE (IC401) B+
13 X-OUT
I2C-DATA
I2C-CLK
MRESET
D514
D+3.3V
EEPROM (IC101), CLOCK GENERATOR (IC102),
SYSTEM CONTROLLER (IC103),
FLASH MEMORY (IC107),
GATE ARRAY (IC202), D-RAM (IC303),
SDRAM (IC504, 505) B+
95 KEY0
2
1
4
AC IN
TO TA-S9D
DVP-S9
Ver 1.5
6-5.
• Circuit Boards Location
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
f
: internal component.
•
•
: Pattern from the side which enables seeing.
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• MB board is multi-layer board.
However, the patterns of intermediate-layer not been included
in diagram.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
•
: internal component.
• C : panel designation.
MB board
VIDEO board
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : DVD PLAY
(
) : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
c : DVD PLAY
J : CD PLAY
L : DVD/CD PLAY (VIDEO OUT)
F : DVD/CD PLAY (AUDIO OUT)
I : DVD/CD PLAY (DIGITAL OUT)
• Abbreviation
AUS : Australian model
EA
: Saudi Arabia model
KR
: Korean model
MX
: Mexican model
SP
: Singapore model
TH
: Thai model
• Refer to servicing notes (page 4) for discrimination of
TYPE A/B.
SUB PANEL board
MAIN board
PANEL board
TRAY SENSOR board
IN OUT SW board
RF board
DRIVER board
MOTOR board
DISC SENSOR board
27
27
DVP-S9
Ver 1.5
6-6.
PRINTED WIRING BOARD – RF Board –
1
2
• See page 27 for Circuit Boards Location.
3
4
5
• Refer to servicing notes (page 4) for discrimination of TYPE A/B.
6
7
8
RF BOARD (COMPONENT SIDE)
A
9
10
11
12
13
14
RF BOARD (CONDUCTOR SIDE)
B
L001
C009
C021
L002
R020
R023
D004
D001
E
B
E
C024 R025
C023
Q002
C018
R010
Q001
R029
C
B
R008
R007
R011
C
C
C017
26
CN001
R038
C034
R006
D
R003
R005
C026
C036
C040
C001
32
C046
16
C008
C047
E
C006
IC001
C043
C019
48
C039
64
C035 C032
C005
C022
C016
C028
C027
R037
C007
1
49
F
OPTICAL
PICK-UP
BLOCK
(KHM-240AAA)
(TYPE A)
(KHM-270AAA)
(TYPE B)
17
33
C048
1
C002
C038
C033 C031
C025
R002
C015
R045
R009
C044
B
MB BOARD
CN015
G
(Page 32)
CN002
11
1-682-815-
H
A
11
(11)
1-682-815-
MB BOARD
CN010
(Page 32)
• Semiconductor
Location
Ref. No.
Location
D001
D004
B-5
B-4
IC001
E-4
Q001
Q002
C-5
C-3
28
28
(11)
DVP-S9
Ver 1.5
6-7.
SCHEMATIC DIAGRAM – RF Board –
• See page 44 for Waveforms.
• Refer to servicing notes (page 4) for discrimination of TYPE A/B.
OPTICAL
PICK-UP
BLOCK
(KHM-240AAA)
(TYPE A)
(KHM-270AAA)
(TYPE B)
(Page 34)
(Page 34)
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
29
29
DVP-S9
6-8.
PRINTED WIRING BOARDS – DISC SENSOR/DRIVER/IN OUT SW/MOTOR/TRAY SENSOR Boards –
1
2
3
• See page 27 for Circuit Boards Location.
4
5
A
1
6
7
8
5
B
C
B
C
D
C
MB
BOARD
CN203
(Page 32)
E
• Semiconductor
Location
Ref. No.
30
30
Location
IC701
IC731
IC732
IC733
IC751
D-8
A-1
A-2
A-4
E-5
Q701
B-8
DVP-S9
Ver 1.2
6-9.
SCHEMATIC DIAGRAM – DISC SENSOR/DRIVER/IN OUT SW/MOTOR/TRAY SENSOR Boards – • See page 46 for IC Block Diagram.
RPI-321
IC731
SUB TRAY1
HEIGHT SENSOR
RPI-321
IC732
SUB TRAY2
HEIGHT SENSOR
RPI-321
IC733
SUB TRAY3
HEIGHT SENSOR
C
MB
BOARD (6/6)
CN203
(Page 39)
IC751
DISC IN
DETECT
31
31
DVP-S9
6-10. PRINTED WIRING BOARD – MB Board (Component Side) –
• Semiconductor
Location
4
5
6
7
8
9
10
11
(Page 42)
A
F
VIDEO BOARD
CN201
MB BOARD (COMPONENT SIDE)
CN012
B
R740
L701
C766
C
D
CN010
RF BOARD
CN002
(Page 28)
R343
R345
C336
104
R316
53
C743
C742
C764
C339
C340
C324
R356
C104
C108
IC302
C306
C320
C307
C310
C347
C309
R315
C348
C311
R313
R314 C313 C351
C107
R206
R207
X102
36
R107
157
F
R328
C331
R140
R137
208
R384
R509
C304
R739
48
R125
C
DRIVER
BOARD
CN701
IC202
C105
1
CN203
25
24
R319 R385
156
R203
37
C111
C106
C312
C744
52
R336
E
FB714 R719
C701
105
R342
R338
C745
C765
R352 R349
A
R341
C317
R334
C319
R337
C345
R330
R332
R368
C315
C349
H-5
H-10
F-10
E-5
H-7
3
(Page 30)
13
1
R510
R508
60
1
C352
61
G
240
C512
C505
120
R414 R412
R419
C403
C404
C401
R417
C406
C405
R413
R301
C414
R302
C420
R143
R304
R174
R327
1
3
30
C506
C422
C416
C418
C112
60
R105 R133 R111
R522
R121
R106
C419
181
120
R182
R114
X101
R185
C502
C501
C006
C004
61
31
C005
I
R129
R179
IC103
IC503
R518
R433
R432
90
C521
IC006
R425
H
91
1
R415
R439
Location
IC006
IC103
IC202
IC302
IC503
2
R317
Ref. No.
1
• See page 27 for Circuit Boards Location.
C529
121
R525 180
R186
RV501
C110
R164
R170
CN404
(FOR TEST)
CN015
1
R165
CN008
9
10
CN103
(FOR TEST)
CN101
5
1
5
1-682-90011
J
(11)
B
OPTICAL
PICK-UP
BLOCK
(Page 28)
D
32
32
MAIN BOARD
NO106
(Page 40)
E
MAIN BOARD
CN107
(Page 40)
DVP-S9
Ver 1.5
6-11. PRINTED WIRING BOARD – MB Board (Conductor Side) –
1
2
3
• See page 27 for Circuit Boards Location.
4
5
6
• Refer to servicing notes (page 4) for discrimination of TYPE A/B.
7
8
9
• Semiconductor
Location
10
Ref. No.
A
MB BOARD (CONDUCTOR SIDE)
B
R701
R737 R738
R713 C721 C722
C
R725
FB711
R717
R718
R724
Q711
R712 C716 C717
1
R711 C711 C712
R312
C337
L711
B C702
FL101
Q712
D
50
C343
E
B
R305
C332 R311 R309
R351
R344
R350
C322
C318
R335
R299
C327
R199
C334
1
C
E
R306
R310
L713
C741 16
C
L715
8
R308
R307
FB712
IC701
9
C323
R320
11
R101
FL202
36
C341
FL203
C207
R211 R212 C204
IC102
R141
9
R214
R209
R124
R138
C205
C344
25
26
C338
C511
C538
IC505
C516
R168 8
R175
R117
R118
R119
R147
FL103
C524
5
7
FL102
4
2
1
C525
3
R167
C536
R421
52
C417
42
R435
37
24
25
30
51
31
36
R524
FB008
FB007 FL003
C526 C545
1
14
R533
IC401
19
FB010
FB009
C534
R429
C412
48
R431
C413
R434
43
50
FL004
R430
1
18
C542
C531
6
C019
FL505
R532
C530
49
C522
IC504
R131
8
7
R406
R418
R427
C407 C402
13
C541
FL502
R157
C430 C429
C415 C411 12
C018
IC106 IC501
IC101 R187
R188
J
C537
R130
C103
1
C547
C523
R116
IC502
FL501
C532
R134
R163
R152
R155
R149
R132
R153
R154 R150 C113
R151
R128
C109
C114
C124
R123
R146
48
5
C519
C546
R172
4
C518
C520
R183
C119
1
R428
C503
R160
R161
C301
R409 R408 R407
R410 R411
R422
C408
IC107
R517
R521
R423
R516
C540
R512
R511
R514
3 1
R424
C513
C514
R162
1
R329
C533
24
R184
3
5
R318
R515
R416
R420
C535
R507 C504
4
C539
C509
C116
25
I
C305
C510
R112
R113
C333
R513
C508
H
C321
IC301
FB112
R156
R076
R077
(TYPE A)
R109
F
R145
C350
C335
R078
R321
R202
C206
R210
G
C346
R136
1
16
C202
R208
C342
8
R142
R126
C203
R215
IC303
R426
E
40
15
FL204
C328
C325
C326
R554
R080
R021
FB011
FL005
FB012
R017
R166
C007
11
1-682-900-
33
33
(11)
Location
IC101
IC102
IC106
IC107
IC301
IC303
IC401
IC501
IC502
IC504
IC505
IC701
I-3
E-5
I-3
G-3
F-9
D-7
H-9
I-4
G-8
H-6
G-6
C-5
Q711
Q712
D-4
D-4
DVP-S9
Ver 1.5
6-12. SCHEMATIC DIAGRAM – MB Board (1/6) –
• Refer to servicing notes (page 4) for discrimination of TYPE A/B.
(Page 35)
(Page 29)
∗ R077
330 (TYPE A)
10k (TYPE B)
(Page 37)
∗
(Page 35)
(TYPE A)
(Page 35)
(Page 39)
(Page 38)
(Page 37)
(Page 29)
(Page 35)
(Page 37)
(Page 35)
(Page 36)
(Page 41)
(Page 39)
34
34
DVP-S9
6-13. SCHEMATIC DIAGRAM – MB Board (2/6) –
• See page 44 for Waveforms.
(Page 36)
(Page 36)
(Page 36)
(Page 37)
(Page 34)
(Page 37)
(Page 37)
(Page 37)
(Page 36)
(Page 34)
(Page 37)
(Page 34)
(Page 34)
(Page 37)
35
35
(Page 34)
(Page 37)
DVP-S9
6-14. SCHEMATIC DIAGRAM – MB Board (3/6) –
• See page 44 for Waveforms.
(Page 37)
(Page 37)
(Page 37)
(Page 37)
(Page 37)
(Page 37)
(Page 37)
(Page 37)
(Page 38)
(Page 35)
(Page 35)
(Page 35)
(Page 34)
(Page 37)
(Page 35)
(Page 38)
36
36
DVP-S9
6-15. SCHEMATIC DIAGRAM – MB Board (4/6) –
• See page 44 for Waveforms.
• See page 46 for IC Block Diagram.
(Page 36)
(Page 35)
(Page 35)
(Page 36)
(Page 39)
(Page 36)
(Page 39)
(Page 35)
(Page 36)
(Page 34)
(Page 36)
(Page 39)
(Page 35)
(Page 36)
(Page 38)
(Page 41)
(Page 34)
(Page 35)
(Page 38)
(Page 35)
(Page 35)
(Page 36)
(Page 36)
(Page 36)
(Page 39)
(Page 34)
37
37
DVP-S9
6-16. SCHEMATIC DIAGRAM – MB Board (5/6) –
• See page 44 for Waveforms.
• See page 46 for IC Block Diagram.
(Page 34)
(Page 37)
(Page 36)
(Page 43)
(Page 37)
(Page 36)
38
38
DVP-S9
6-17. SCHEMATIC DIAGRAM – MB Board (6/6) –
(Page 34)
(Page 37)
(Page 37)
(Page 31)
(Page 37)
(Page 37)
(Page 34)
39
39
DVP-S9
1
• See page 27 for Circuit Boards Location.
2
3
4
5
6
7
(Page 32)
(Page 42)
MB BOARD
CN101
VIDEO BOARD
CN202
E
G
8
9
10
(Page 32)
D
MB BOARD
CN008
AC IN
TO TA-S9D
POWER BLOCK
MAIN BOARD
A
LP104
R429
JW128
R411
R432
R486
R487
R484
JW120
R485
C501
14
JW113
JW114
D505
C512
D513
C405
R495
C101
9
R103
R101
R497
D503
C102
D105
R102
D
IC502
C500
R132
R489
R133
R490
R488
R491
R104
R493
JW123
JW124
R483
R496
JW147
R492
JW146
JW131
C408
JW132
R459
R480
JW121
81
C514
D512
JW111
JW126
80
D514
JW107
R134
R494
D501
D504
D502
EL103
CN101
100
JW402
IC401
R482
JW407
1
R454
JW133
15
JW105
C406
51
CN103
SYSTEM CONTROL 5
FROM TC-S9
CN103
IC501
C513
C402
R456
2
C508
50
R453
1
JW103
C509
JW115
R451
R457
FB503
EL102
X401
R448
8
CN102
LP102
R425
R412
R409
C425
R413
30
C404
31
R455
11
1
H
Location
D-7
C-9
C-9
C-9
C-9
C-8
D-8
C-8
C-8
IC401
IC501
IC502
C-4
B-8
C-8
(11)
SYSTEM CONTROL 3
FROM ST-S9
• Semiconductor
Location
D105
D501
D502
D503
D504
D505
D512
D513
D514
1-682-811-
PANEL BOARD
NO703
(Page 42)
Ref. No.
9
C557
C401
EL105
1
C507
JW118
JW125
C
JW108
JW119
NO104
1
NO106
C502
R477
JW102
JW117
R441
R481
8
2
C505
C403
1
C506
C504
LP103
R469
R473
FB501
NO105
1
R417
JW137
R465
R444
JW138
R435
R447
JW145
R442
C407
9
R440
R437
JW144
CN401
R443
JW140
B
R436
JW143
R430
R419
R433
C411
R434
FB502
EL104
JW130
R431
1
JW100
9
10
CN107
EL101
JW101
1
2
C427
CN501
(FOR TEST)
LP101
10
CN503
(FOR TEST)
R427
1
JW127
4
R567
1
JW151
6-18. PRINTED WIRING BOARD – MAIN Board –
40
40
DVP-S9
6-19. SCHEMATIC DIAGRAM – MAIN Board –
• See page 44 for Waveform.
(Page 43)
(Page 34)
(Page 37)
(Page 43)
41
41
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
DVP-S9
6-20. PRINTED WIRING BOARDS – PANEL/SUB PANEL/VIDEO Boards –
1
2
• See page 27 for Circuit Boards Location.
3
4
5
6
7
J202
A
9
IC201
OPTICAL
OUT
TO ST-S9
VIDEO OUT
VIDEO BOARD
8
PANEL BOARD
10
SUB PANEL BOARD
J201
9
S VIDEO OUT
1
C204
NO703
H
MAIN
BOARD
CN401
R712
S711
R711
B
m
2
1
FB204
4
3
C206
JW201
3
1
IC201
FB203
FB201
FB202
2
CN201
L201
C203
CN202
1
(Page 40)
1-682-813-
11
S707
S708
(11)
REPEAT
PLAY MODE
S712
F
M
S711 – 720
MB BOARD
CN012
G
(Page 32)
MAIN BOARD
NO105
S701 – 708
(Page 40)
S706
R706
R707
S713
S714
Z
>
.
R705
R704
(DISC 3)
S705
C
1
2
D702
D701
R713
D702, S717
D703
N
3
D704
2 (DISC 2)
x
S716
R714
R715
R716
S701
1
2
DISC 3 R701
Z
(DISC 2)
(DISC 1)
S702
DISC 2 R702
S703
DISC 1
R703
(DISC 1)
(DISC 3)
S715
D705
1
NO701
NO702
S704
Z
S717
R717
D701, S716
X
S718
RETURN
D
S720
NEXT
R718
S719
PREV
R719
11
1-682-812-
• Semiconductor
Location
Ref. No.
Location
D701
D702
D703
D704
D705
C-2
C-2
C-5
C-6
C-7
IC201
A-7
42
42
(11)
11
1-682-814-
(11)
DVP-S9
6-21. SCHEMATIC DIAGRAM – PANEL/SUB PANEL/VIDEO Boards –
(Page 38)
(Page 41)
(Page 41)
43
43
DVP-S9
• Waveforms
– RF Board –
– MB Board –
6 IC001 rs (FE) (CD PLAY)
1 IC001 2 (RF IN) (DVD PLAY)
Approx.
570 mVp-p
8 IC302 <zx, (RFIN2) (CD PLAY)
Approx.
600 mVp-p
qd IC302 <zcn (ADC1) (CD PLAY)
Approx.
1.4 Vp-p
qk IC503 uf (YOUT) (COLOR BAR (NTSC))
Approx.
600 mVp-p
wd IC503 i; (COMPOUT)
(COLOR BAR (PAL))
1 Vp-p
1 Vp-p
H
H
2 IC001 2 (RF IN) (CD PLAY)
7 IC001 tl (SIGO) (DVD/CD PLAY)
Approx.
550 mVp-p
9 IC302 <zcz (RFIN1) (DVD PLAY)
Approx.
1.4 Vp-p
qf IC302 <z,x (CLKIN), <z,m (MCKI), <z,. (SCKI)
Approx.
1.4 Vp-p
ql IC503 uf (YOUT) (COLOR BAR (PAL))
wf IC503 <z,/ (CLKI), <z,x (SCLKIN)
1 Vp-p
3.4 Vp-p
3.4 Vp-p
H
29.5 ns
3 IC001 ra (TE) (DVD PLAY)
0 IC302 <zcb (ADC0) (DVD PLAY)
Approx.
120 mVp-p
37 ns
qg IC503 qs (ACLK) (DVD PLAY)
Approx.
120 mVp-p
w; IC503 uj (COUT) (COLOR BAR (NTSC))
wg IC103 tf (X0)
710 mVp-p
3.4 Vp-p
1.8 Vp-p
H
60.6 ns
40.7 ns
4 IC001 ra (TE) (CD PLAY)
qa IC302 <zcb (ADC0) (CD PLAY)
Approx.
800 mVp-p
qh IC503 qs (ACLK) (CD PLAY)
Approx.
800 mVp-p
wa IC503 uj (COUT) (COLOR BAR (PAL))
wh IC102 3 (27-1OUT)
710 mVp-p
3.4 Vp-p
3.4 Vp-p
H
37 ns
44.3 ns
5 IC001 rs (FE) (DVD PLAY)
qs IC302 <zcn (ADC1) (DVD PLAY)
Approx.
180 mVp-p
qj IC503 wl (CRPCLKI)
Approx.
180 mVp-p
3.4 Vp-p
29.5 ns
44
ws IC503 i; (COMPOUT)
(COLOR BAR (NTSC))
44
wj IC102 7 (XTI)
1.6 Vp-p
1 Vp-p
H
37 ns
DVP-S9
– MAIN Board –
wk IC102 9 (512-2OUT), 0 (512-1OUT)
(DVD PLAY)
ed IC701 qd (OUTB1) (COLOR BAR (NTSC)) ej IC401 qd (X-OUT)
2 Vp-p
2.5 Vp-p
3.4 Vp-p
H
40.7 ns
wl IC102 9 (512-2OUT), 0 (512-1OUT)
(CD PLAY)
62.5 ns
ef IC701 qd (OUTB1) (COLOR BAR (PAL))
2 Vp-p
3.4 Vp-p
H
44.3 ns
e; IC102 qd (33-2OUT), qg (33-1OUT)
eg IC701 qg (OUTA1) (COLOR BAR (NTSC))
1.8 Vp-p
3.4 Vp-p
H
29.5 ns
ea IC701 0 (OUTC1) (COLOR BAR (NTSC)) eh IC701 qg (OUTA1) (COLOR BAR (PAL))
2 Vp-p
1.8 Vp-p
H
H
es IC701 0 (OUTC1) (COLOR BAR (PAL))
2 Vp-p
H
45
DVP-S9
• IC Block Diagrams
– DRIVER Board –
IC701
BA6956AN
TSD
RNF
OUT1
6
7
8
9
RIN
OUT2
5
GND
4
FIN
3
VCC
2
VM
1
VREF
CONTROL LOGIC
– MB Board –
IC102
IMIC6001BTD
VDD 1
VSS 2
16 TEST
27-1OUT 3
PLL1
15 33-1OUT
14 FSEL
27-2OUT 4
13 33-2OUT
VDD 5
12 VDD
VSS 6
11 VSS
XTI 7
OSC
PLL2
10 512-1OUT
XTO 8
9 512-2OUT
IC701
BA7666FS-E2
MUTE 1
INA 2
16 VCC
6dB
75Ω
GND 3
INB 4
14 OUTA2
6dB
75Ω
GND 5
GND 8
46
13 OUTB1
12 OUTB2
NC 6
INC 7
15 OUTA1
11 NC
6dB
75Ω
10 OUTC1
9 OUTC2
DVP-S9
6-22.
IC PIN FUNCTION DESCRIPTION
• RF BOARD IC001 SP3728AC (DVD/CD RF AMP, FOCUS/TRACKING ERROR AMP)
Pin No.
Pin Name
I/O
Description
1, 2
RFIP, RFIN
I
RF signal input terminal
3
CP
—
Tracking LPF terminal
4
WIN
I
Wobble detection signal input terminal Not used (open)
5
WPP
O
Wobble push-pull signal output terminal Not used (open)
6
CN
—
Tracking LPF terminal
7 to 10
A2 to D2
I
Photo detector interface input terminal (AC coupled input for the DPD and wobble)
11 to 14
D to A
I
Photo detector interface input terminal (main)
15 to 18
E to H
I
Photo detector interface input terminal (sub)
19
VC
O
Reference voltage (+2.5V) output terminal
20
VPB
—
Power supply terminal (+5V) (servo block)
21
DVDPD
I
DVD APC signal input terminal
22
CDPD
I
CD APC signal input terminal
23
VNB
—
Ground terminal (servo block)
24
LDSELO
O
APC LD select signal output terminal
25
DVDLD
O
DVD APC signal output terminal
26
CDLD
O
CD APC signal output terminal
27
LDON
I
APC LD output control signal input terminal
28
MEVO
O
Envelope signal output terminal for mirror
29
MIN
I
RF signal input terminal for mirror
30
MP
—
Mirror top hold terminal
31
MB
—
Mirror bottom hold terminal
32
MLPF
—
Mirror LPF terminal
33
MIRR
O
Mirror detect signal output to the servo DSP (IC302)
34
BYP2
—
Servo AGC gain control terminal
35
PII
I
Pull-in signal input terminal
36
PI
O
Pull-in signal output terminal
37
TZC
O
Tracking zero crossing signal output to the servo DSP (IC302)
38
DFT
O
Defect signal output to the servo DSP (IC302)
39
VCI
I
Reference voltage input terminal
40
TZIN
I
Tracking zero crossing signal input terminal
Tracking error signal output to the servo DSP (IC302)
41
TE
O
42
FE
O
Focusing error signal output to the servo DSP (IC302)
43
TPH
—
PI top hold terminal
44
MON
O
Monitor signal output to the servo DSP (IC302)
45
SRD
O
Serial data output to the servo DSP (IC302)
46
SWD
I
serial data input from the servo DSP (IC302)
47
SCLK
I
Serial clock signal input from the servo DSP (IC302)
48
SDEN
I
Serial data enable signal input from the servo DSP (IC302)
49
V33
—
50
RX
I
51
TPA
—
RF top hold terminal
52
MEV
—
RF bottom envelope terminal
53
VNA
—
Ground terminal (RF block and serial port)
54, 55
FNN, FNP
O
Differential filter normal signal output terminal
56, 57
DIP, DIN
I
Analog signal input terminal for RF single buffer
Power supply terminal (+3.3V) (CMOS output buffers)
Reference resistor input terminal
47
DVP-S9
Pin No.
Pin Name
I/O
58
BYP
—
RF AGC gain control terminal
59
SIGO
O
Single-ended RF signal output terminal
60
VPA
—
Power supply terminal (+5V) (RF block and serial port)
61, 62
AIP, AIN
I
AGC amp signal input terminal
63, 64
ATON, ATOP
O
Differential attenuator signal output terminal
48
Description
DVP-S9
• MB BOARD IC103 MB91307APFV-G-BND-E1 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
1 to 5
HA17 to HA21
O
Description
Address signal output terminal
6
HA22
—
Not used (open)
7
WP
O
Write control signal output to the EEPROM (IC101)
8
TRM/XKRCS
—
Not used (open)
9
AVCC
—
Power supply terminal (+3.3V) (for A/D converter)
10
AVRH
—
Reference voltage input (+3.3V) terminal (for A/D converter)
11
AVSS
—
Ground terminal (for A/D converter)
12
AN0
I
Mode 0 set input terminal
13
AN1
I
Mode 1 set input terminal
14
AN2
I
Mode 2 set input terminal
15
AN3
I
Mode 3 set input terminal
16
INT0
I
Interrupt request signal input from the AV decoder (IC503)
17
INT1
I
Interrupt request signal input from the ARP (IC302)
18
INT2
I
Interrupt request signal input from the servo DSP (IC302)
19
INT3
I
Interrupt request signal input from the gate array (IC202)
20
INT4
I
Interrupt request signal input from the interface controller (IC401)
21, 22
INT5, INT6
—
Not used (fixed at “H”)
23
INT7
—
Not used (open)
24
VCC
—
Power supply terminal (+3.3V)
25
SI0
I
Serial data input from the interface controller (IC401)
26
SO0
O
Serial data output to the interface controller (IC401)
27
SC0
O
Serial clock signal output to the interface controller (IC401)
28
SI1
I
Serial data input terminal Not used (open)
29
SO1
O
Serial data output terminal Not used (open)
30
SC1
O
Serial clock signal output terminal Not used (open)
31
SI2
I
Serial data input terminal (for test)
32
SO2
O
Serial data output terminal (for test)
33
DSENS
—
Not used (open)
34
VSS
—
Ground terminal
35
XRST
O
System reset signal output terminal “L”: reset
36
XARPPST
O
Reset signal output to the ARP (IC302) “L”: reset
37
RGBSEL/MICMUTE
—
Not used (open)
38
SDA
I/O
Two-way data bus with EEPROM (IC101)
39
SCL
O
Serial clock signal output to the EEPROM (IC101)
40
TRM+/XKRRST
—
Not used (fixed at “L”)
41
EUROV/Y/CLAPSW1
—
Not used (open)
42
DISCEXT/CLPSW0
—
Not used (open)
43
MD0
I
Mode select 0 signal input terminal (fixed at “H” in this set)
44
MD1
I
Mode select 1 signal input terminal (fixed at “L” in this set)
45
MD2
I
Mode select 2 signal input terminal (fixed at “L” in this set)
46
DREQ0
I
Request 0 signal input from the AV decoder (IC503)
47
DACK0
O
Acknowledge 0 signal output to the AV decoder (IC503)
48
XDRVMUTE
O
Drive mute signal output terminal
49
DREQ1
I
Request 1 signal input from the AV decoder (IC503)
50
DACK1
O
Acknowledge 1 signal output to the AV decoder (IC503)
49
DVP-S9
Pin No.
Pin Name
51
XIFCS
O
Chip select signal output to the interface controller (IC401)
52
VSS
—
Ground terminal
53
X1
O
System clock output terminal (16.5MHz)
54
X0
I
System clock input terminal (16.5MHz)
55
VCC
—
Power supply terminal (+3.3V)
56
CKSW1
—
Not used (open)
57
OCSSW1
—
Not used (open)
58
CS0X
O
Chip select signal output to the flash memory (IC107)
59
CS1X
—
Not used (open)
60
CS2X
O
Chip select signal output to the AV decoder (IC503)
61
CS3X
O
Chip select signal output to the AV decoder (IC503)
62
CS4X
O
Chip select signal output to the ARP (IC302)
63
CS5X
O
Chip select signal output to the Servo DSP (IC302)
64
C
—
Capacitor connected terminal
65
CS6X
O
Chip select signal output to the gate array (IC202)
66
CS7X
—
Not used (open)
67
XWAIT
I
68
BGRNTX
—
Not used (fixed at “H”)
69
BGR
—
Not used (open)
70
XRD
O
Read enable signal output terminal
71
XWRH
O
High byte write enable signal output terminal
72
XWRL
—
Not used (open)
73
NMIX
—
Not used (fixed at “H”)
74
HSTX
—
Not used (fixed at “H”)
75
VSS
—
Ground terminal
76
XFRRST
I
Reset signal input from the interface controller (IC401) “L”: reset
77
CPUCK
O
CPU clock signal output terminal
78
OCSW2
—
Not used (fixed at “H”)
79
XDACX
—
Not used (fixed at “H”)
80
VESCS/X39CS
—
Not used (fixed at “H”)
81
48/44.1K
O
Sampling frequency selection signal output terminal “L”: 48kHz, “H”: 44.1kHz
82
WIDE
O
Wide signal output terminal
83
MAMUTE
I
System OK signal input terminal
84
XLDON
O
LD control signal output terminal
85 to 100
HD0 to HD15
I/O
Two-way data bus terminal
101
VSS
—
Ground terminal
102 to 109
HA0 to HA7
O
Address signal output terminal
110
VCC
—
Power supply terminal (+3.3V)
111 to 118
HA8 to HA15
O
Address signal output terminal
119
VSS
—
Ground terminal
120
HA16
O
Address signal output terminal
50
I/O
Description
Wait signal input terminal
DVP-S9
• MB BOARD IC302 CXD9635R (SERVO DIGITAL SIGNAL PROCESSOR, ARP)
Pin No.
Pin Name
I/O
1
VSS
—
Description
Ground terminal (for digital system)
2 to 9
D0 to D7
I/O
Two-way data bus terminal
10
VDD 3.3V
—
Power supply terminal (+3.3V) (for digital system)
11 to 15
A0 to A4
I
16
VSS
—
17 to 19
A5 to A7
I
20
VDD 1.8V
—
Power supply terminal (+1.8V) (for digital system)
21
XINT
O
Interrupt request signal output to the system controller (IC103)
22
HINT
O
Interrupt request signal output to the system controller (IC103)
23
XCS
I
Chip select signal input from the system controller (IC103)
Address signal input terminal
Ground terminal (for digital system)
Address signal input terminal
24
HCS
I
Chip select signal input from the system controller (IC103)
25
XWAT
O
Wait signal output terminal
26
VSS
—
Ground terminal (for digital system)
27 to 36
MA0 to MA9
O
Address signal output to the D-RAM (IC303)
37
VDD 3.3V
—
Power supply terminal (+3.3V) (for digital system)
38
XMWR
O
Write enable signal output to the D-RAM (IC303)
39
XCAS
O
CAS signal output to the D-RAM (IC303)
40
VSS
—
Ground terminal (for digital system)
41
XRAS
O
RAS signal output to the D-RAM (IC303)
42
XOE
O
Output enable signal output to the D-RAM (IC303)
43
VDD1 1.8V
—
Power supply terminal (+1.8V) (for digital system)
44 to 51
MD0 to MD7
I/O
Two-way data bus with the D-RAM (IC303)
52
VSS
—
Ground terminal (for digital system)
53 to 60
MD8 to MD15
I/O
Two-way data bus with the D-RAM (IC303)
61
VDD 3.3V
—
Power supply terminal (+3.3V) (for digital system)
62
DATA
O
CD data output to the AV decoder (IC503)
63
BCLK
O
CD bit clock signal output to the AV decoder (IC503)
64
VSS
—
Ground terminal (for digital system)
65
LRCK
O
CD LR clock signal output to the AV decoder (IC503)
66
DOUT
O
Digital signal output to the AV decoder (IC503)
67
VDD 1.8V
—
Power supply terminal (+1.8V) (for digital system)
68
SDCK
O
SD bus clock signal output to the AV decoder (IC503)
69
XSHD
O
SD bus header signal output to the AV decoder (IC503)
70
XSRQ
I
SD bus request signal input from the AV decoder (IC503)
71
XSAK
O
SD bus acknowledge signal output to the AV decoder (IC503)
72
SDEF
O
SD bus error flag signal output to the AV decoder (IC503)
73 to 81
SD0 to SD7
O
SD bus data output to the AV decoder (IC503)
82
VDD 3.3V
—
Power supply terminal (+3.3V) (for digital system)
83 to 88 MNT0 to MNT5
I/O
Monitor signal input/output terminal Not used (open)
89, 90
MNT6, MNT7
I/O
Monitor signal input/output terminal Not used (fixed at “H”)
91
ESTB
O
Error strobe signal output terminal Not used (open)
92
VDD 1.8V
—
Power supply terminal (+1.8V) (for digital system)
93
RFD
I/O
RF digital data input/output terminal Not used (fixed at “H”)
94
VSS
—
Ground terminal (for digital system)
51
DVP-S9
Pin No.
Pin Name
I/O
95
PLCKO
O
Not used (open)
O
Not used (fixed at “H”)
96 to 103 ADO0 to ADO7
Description
104
VSS
—
Ground terminal (for digital system)
105
VSSA4
—
Ground terminal (for analog system)
106
VCO
I
VCO control signal input terminal
107, 108
R1, R2
I
VCO outside resistance signal input terminal
109
VDDA4 3.3V
—
Power supply terminal (+3.3V) (for analog system)
110
VSSA3
—
Ground terminal (for analog system)
111
INP
I
OP amp positive input terminal
112
INM
I
OP amp negative input terminal
113 to 115
FR3 to FR1
I
Feedback resistance signal input terminal
116
Y
O
OP amp output terminal
117
VDDA3 3.3V
—
Power supply terminal (+3.3V) (for analog system)
118
VREF
I
Reference voltage input terminal (for D/A converter)
119
BIAS
I
Bias input terminal (for D/A converter)
120
VDDA2 3.3V
—
Power supply terminal (+3.3V) (for analog system)
121
VSSA2
—
Ground terminal (for analog system)
122
AOUT
O
D/A converter output terminal (for D/A converter)
Reference current input terminal (for D/A converter)
123
IREF
I
124
VSSD2
—
Ground terminal (for D/A converter)
125
VDDD2 3.3V
—
Power supply terminal (+3.3V) (for D/A converter)
126
VRT
I
127
VDDA1 3.3V
—
128
RFIN2
I
129
NMIX
—
RF signal input terminal Not used
130
VSSA1
—
Ground terminal (for analog system)
131
RFIN1
I
RF signal input terminal
132
VRB
I
A/D converter reference input terminal
133
VSSD1
—
Ground terminal (for A/D converter)
134
VDDD1 3.3V
—
Power supply terminal (+3.3V) (for A/D converter)
135
ADC0
I
Tracking error signal input from the SP3728AC (IC001)
136
ADC1
I
Focusing error signal input from the SP3728AC (IC001)
Pull-in signal input from the SP3728AC (IC001)
A/D converter reference input terminal
Power supply terminal (+3.3V) (for analog system)
RF signal input terminal
137
ADC2
I
138
VDDA0 3.3V
—
139
ADC3
I
Tracking coil drive signal input from the FAN8034 (IC401)
140
ADC4
I
Spindle motor drive signal input from the FAN8034 (IC401)
Power supply terminal (+3.3V) (for analog system)
141
VSSA0
—
142, 143
ADC5, ADC6
I
A/D converter input terminal
144
ADC7
I
Monitor signal input from the SP3728AC (IC001)
145
VDDD0 3.3V
—
Power supply terminal (+3.3V) (for A/D converter)
146
VSSD0
—
Ground terminal (for A/D converter)
147
VRBA
I
148
VSSA0
—
Ground terminal (for analog system)
52
Ground terminal (for analog system)
A/D converter reference input terminal
149
TESTAA
O
ASW output terminal Not used (open)
150
VDDA0 3.3V
—
Power supply terminal (+3.3V) (for analog system)
DVP-S9
Pin No.
Pin Name
151
VRTA
I
152
VSS
—
153 to 155 TESTK0 to TESTK2
I/O
Description
A/D converter reference input terminal
Ground terminal (for digital system)
I
Test signal input terminal (fixed at “L”)
I
DSP reset signal input from the system controller (IC103)
“L”: reset
ARP reset signal input from the system controller (IC103)
“L”: reset
156
XDSPRST
157
XARPRST
I
158
VSS
—
Ground terminal (for digital system)
159
MDS0
O
Spindle motor drive signal output to the FAN8034 (IC401)
160
MON
O
Motor ON/OFF signal output terminal Not used (open)
161
MDP0
O
Spindle motor drive signal output to the FAN8034 (IC401)
162
DFCT
O
Defect detection signal output terminal
163
JITPWM
O
Jitter PWM signal output terminal Not used (open)
164
LOCK
O
EFM lock detection signal output terminal Not used (open)
165
VDD1 1.8V
—
Power supply terminal (+1.8V) (for digital system)
166
GIO0/INT2
I
Inlimit sensor input terminal
167
GIO1/INT3
O
Spindle motor drive control signal output to the FAN8034 (IC401)
168
GIO2/INT4
I
TSD-M signal input from the FAN8034 (IC401)
169
GIO3/INT5
—
Not used (open)
170
VDD 3.3V
—
Power supply terminal (+3.3V) (for digital system)
171
GIO4/PGREF
—
Not used (open)
172
GIO5/PGIN
I
Monitor signal input from the SP3728AC (IC001)
173
GIO6/SDI
I
Serial data input from the SP3728AC (IC001)
174
GIO7/SDO
O
Serial data output to the SP3728AC (IC001)
175
GIO8/SCK
O
Serial clock signal output to the SP3728AC (IC001)
176
GIO9/FGREF
O
Motor drive signal output terminal Not used
177
GIO10/FGIN
O
Motor drive signal output terminal Not used
178
GIO11/TMC2
—
Not used (open)
179
GIO12
—
Not used (open)
180
GIO13
O
Serial data enable signal output to the SP3728AC (IC001)
181
VSS
—
Ground terminal (for digital system)
182
CLKIN
I
183
VSSA5
—
Ground terminal (for analog system)
184
VDDA5 1.8V
—
Power supply terminal (+1.8V) (for analog system)
185
DFCTI
I
186
VSS
—
187
MCKI
I
188
VDD 1.8V
—
189
SCKI
I
190
VSS
—
191
TRST
I
Reset signal input terminal (for JTAG boundary scan)
192
TMS
I
MS signal input terminal (for JTAG boundary scan)
193
TDI
I
Serial data input terminal (for JTAG boundary scan)
194
TCK
I
Clock signal input terminal (for JTAG boundary scan)
195
TDO
O
Serial data output terminal (for JTAG boundary scan)
Clock signal input terminal
Defect signal input from the SP3728AC (IC001)
Ground terminal (for digital system)
Clock signal input terminal
Power supply terminal (+1.8V) (for digital system)
Clock signal input terminal
Ground terminal (for digital system)
196
TZC
I
Tracking zero crossing signal input from the SP3728AC (IC001)
197
MIRR
I
Mirror detect signal input terminal from the SP3728AC (IC001)
53
DVP-S9
Pin No.
Pin Name
I/O
Description
198, 199
PWM0, PWM1
O
Sled motor drive signal output to the FAN8034 (IC401)
200
PWM2
O
Motor drive signal output terminal
201
VDD 3.3V
—
Power supply terminal (+3.3V) (for digital system)
202, 203
PDM0, PDM1
O
Tracking coil drive signal output to the FAN8034 (IC401)
204, 205
PDM2, PDM3
O
Focusing coil drive signal output to the FAN8034 (IC401)
206
VSS
—
Ground terminal (for digital system)
207
XWR
I
Write enable signal input terminal
208
XRD
I
Read enable signal input terminal
54
Not used
DVP-S9
• MAIN BOARD IC401 M30622MAA-B33FP (INTERFACE CONTROLLER)
Pin No.
Pin Name
I/O
Description
1 to 7
NC
—
8
BYTE
I
9
CNVSS
—
Processor mode switch terminal (for test)
10
Not used (fixed at “L”)
Not used (open)
External data bus line byte selection signal input “L”: 16 bits, “H”: 8 bits
Not used (fixed at “L”)
NC
—
11
NC
—
12
RESET
I
System reset signal input terminal
13
X-OUT
O
System clock output terminal (16 MHz)
14
VSS
—
Ground terminal
15
X-IN
I
16
Not used (open)
System clock input terminal (16 MHz)
VCC
—
17
NMI
I
18
NC
—
19
SYS CS
I
20 to 28
NC
—
Not used (open)
29
IIC-CLK
I/O
Communication data reading clock signal input or transfer clock signal output terminal
30
IIC-DATA
I/O
Communication data bus terminal
Power supply terminal (+5V)
Non-maskable interrupt input terminal Not used (fixed at “H”)
Not used (open)
Chip select signal input from the system controller (IC103)
31
TXD1
I
Serial data input terminal (for test)
32
RXD1
O
serial data output terminal (for test)
33
CLK1
O
Serial clock signal output terminal (for test)
34
RTS1
O
RTS signal output terminal (for test)
35
SYS DATAOUT
O
serial data output to the system controller (IC103)
36
SYS DATAIN
I
serial data input from the system controller (IC103)
37
SYS CLK
O
Serial clock signal output to the system controller (IC103)
38
SYS POWER
O
Power ON/OFF control signal output terminal “H”: ON Not used (open)
39
NC
—
Not used (open)
40
SYS RST
O
System reset signal output terminal “L”: reset
41
NO-USE
—
Not used (fixed at “L”)
42
SYS RQ
O
Interrupt request signal output to the system controller (IC103)
43
SYS OK
O
System OK signal output to the system controller (IC103)
44
P.CONT
O
Power block ON/OFF control signal output terminal “H”: ON
45
NC
—
Not used (open)
46
NC
—
Not used (fixed at “H”)
47
DVDFRCHK
O
Flash memory (for DVD) check signal output terminal Not used (fixed at “H”)
48
VMUTE
O
Mute signal output to the video buffer (IC701) “H”: mute
49, 50
NC
—
Not used (open)
51
NC
—
Not used (fixed at “H”)
52
NC
—
Not used (open)
53
B-TRIG
O
Deck-B trigger plunger drive signal output terminal “H”: trigger plunger on
54
ECO CHECK
—
Not used (fixed at “H”)
55
A-TRIG
O
Deck-A trigger plunger drive signal output terminal “H”: trigger plunger on
56 to 58
NC
—
Not used (open)
59
REC/PB/PASS
O
Recording/playback/pass selection signal output terminal
“L”: recording, center voltage: playback, “H”: pass
60, 61
NC
—
Not used (open)
55
DVP-S9
Pin No.
Pin Name
I/O
Description
62
VCC
—
Power supply terminal (+5V)
63
SOFT-TEST
O
For software check terminal Not used (open)
64
VSS
—
Ground terminal
65 to 68
LED_DISC1
O
LED drive signal output of the 1 indicator (D705) “L”: LED on
69 to 72
LED_DISC2
O
LED drive signal output of the 2 indicator (D704) “L”: LED on
73 to 76
LED_DISC3
O
LED drive signal output of the 3 indicator (D703) “L”: LED on
77 to 80
LED_PLAY
O
LED drive signal output of the N indicator (D702) “L”: LED on
81 to 83
LED_PAUSE
O
LED drive signal output of the X indicator (D701) “L”: LED on
84
EXP-IN DATA
I
Serial data input terminal
85
EXP-OUT DATA
O
Serial data output terminal
86
EXP-LAT
O
Serial data latch pulse signal output terminal
87
EXP-CLK
O
Serial clock signal output terminal
88
LED_PAUSE
O
LED drive signal output of the X indicator (D701) “L”: LED on
89
A-SHUT
I
Shut off (deck-A) detection signal input terminal
90
B-SHUT
I
Shut off (deck-B) detection signal input terminal
91
B-HALF
I
Detection input terminal from the deck-B cassette detect switch “L”: cassette in
92
MODEL-IN
I
Model destination setting terminal
93
PWRCHK
—
94
KEY2
I
Key input terminal
95
KEY1
I
Key (S711 to S720) input terminal (A/D input)
96
AVSS
—
97
56
Power check terminal
Fixed at “H”
Ground terminal (for A/D converter)
KEY0
I
98
VREF
I
Key (S701 to S708) input terminal (A/D input)
99
AVCC
—
Power supply terminal (+5V) (for A/D converter)
100
NC
—
Not used (open)
Reference voltage (+5V) input terminal (for A/D converter)
DVP-S9
Ver 1.5
SECTION 7
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Refer to servicing notes (page 4) for discrimination of TYPE A/B.
• Items marked “*” are not stocked since they
The components identified by
mark 0 or dotted line with mark
are seldom required for routine service. Some
0 are critical for safety.
delay should be anticipated when ordering
Replace only with part number
these items.
specified.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Abbreviation
AUS : Australian model
MX : Mexican model
EA : Saudi Arabia model
SP : Singapore model
KR : Korean model
TH : Thai model
7-1. CASE SECTION
4
#2
3
3
#2
5
6
1
F1
7
chassis section
front panel section
#1
Ref. No.
Part No.
Description
01
01
01
3
4
1-476-027-11
1-476-028-11
1-476-029-11
3-363-099-21
4-233-134-11
POWER BLOCK (AUS, EA, SP, TH)
POWER BLOCK (AEP, KR, UK)
POWER BLOCK (E, MX)
SCREW (CASE 3 TP2)
CASE
Remark
05
05
05
1-823-394-11 CORD, POWER (E, MX)
1-823-396-11 CORD, POWER (AEP, AUS, EA, SP, TH, UK)
1-823-399-11 CORD, POWER (KR)
Ref. No.
Part No.
* 6
#1
3-703-244-00 BUSHING (2104), CORD
(AEP, AUS, EA, KR, SP, UK)
3-703-571-11 BUSHING (S) (4516), CORD (E, MX, TH)
4-965-822-01 FOOT
1-532-388-31 MINIATURE FUSE-LINKS, TIME-LAG FUSE
(T2AL/250V)
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
#2
7-685-871-01 SCREW +BVTT 3X6 (S)
6
7
0 F1
Description
Remark
57
DVP-S9
7-2. FRONT PANEL SECTION
55
53
54
not supplied
56
54
57
54
52
not supplied
51
Ref. No.
51
52
53
54
58
Part No.
Description
4-233-136-21
4-233-147-01
X-4953-614-1
4-951-620-01
LID (CD)
SPRING (CD)
PANEL ASSY, FRONT
SCREW (2.6X8), +BVTP
Remark
Ref. No.
55
56
57
Part No.
Description
1-682-814-11 SUB PANEL BOARD
1-682-812-11 PANEL BOARD
4-963-404-21 EMBLEM (5-A), SONY (TH)
Remark
DVP-S9
7-3. CHASSIS SECTION
105
104
not supplied
108
#1
CD mechanism deck section-1
107
106
102
102
103
#1
#1
not
supplied
101
#1
110
109
#1
not supplied
Ref. No.
Part No.
Description
101
102
103
103
103
1-823-609-11
3-970-608-01
A-4727-239-A
A-4727-244-A
A-4727-246-A
WIRE (FLAT TYPE) (25 CORE)
SUMITITE (B3), +BV
MB BOARD, COMPLETE (AEP, UK)
MB BOARD, COMPLETE (AUS)
MB BOARD, COMPLETE (E, MX)
103
103
104
105
106
A-4727-248-A
A-4727-252-A
1-823-608-11
A-4727-237-A
A-4727-238-A
MB BOARD, COMPLETE (EA)
MB BOARD, COMPLETE (KR, SP, TH)
WIRE (FLAT TYPE) (10 CORE)
MAIN BOARD, COMPLETE
VIDEO BOARD, COMPLETE
107
108
1-823-607-11 WIRE (FLAT TYPE) (8 CORE)
1-757-633-11 CORD (WITH CONNECTOR) 17P
Remark
Ref. No.
Part No.
Description
109
109
109
109
109
4-236-808-01
4-236-808-11
4-236-808-31
4-236-808-41
4-236-808-51
PANEL (DVD), BACK (AEP)
PANEL (DVD), BACK (UK)
PANEL (DVD), BACK (KR)
PANEL (DVD), BACK (SP)
PANEL (DVD), BACK (EA)
109
109
109
109
110
4-236-808-61
4-236-808-71
4-236-808-81
4-236-808-91
1-823-611-11
PANEL (DVD), BACK (AUS)
PANEL (DVD), BACK (TH)
PANEL (DVD), BACK (E)
PANEL (DVD), BACK (MX)
WIRE (FLAT TYPE) (9 CORE)
#1
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
Remark
59
DVP-S9
Ver 1.3
7-4. CD MECHANISM DECK SECTION-1
(CDM63D)
507
506
501
not supplied
not supplied
506
501
not supplied
A
501
501
509
508
505
510
513
504
501
503
502
511
512
CD mechanism deck section-2
A
Ref. No.
Part No.
Description
501
502
503
504
505
4-218-253-01
4-228-996-01
4-228-995-01
4-228-972-02
4-228-975-02
SCREW (M2.6), +BTTP
SPRING (R), TORSION
SPRING (L), TORSION
TRAY (MAIN)
COVER (TRAY.L)
506
507
4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
4-234-121-01 PULLEY (A) (DVD), CHUCKING
60
Remark
Ref. No.
Part No.
Description
508
509
510
511
512
4-228-986-02
4-231-858-01
4-228-978-02
4-228-990-03
4-228-991-03
RACK (TRAY.L)
PULLEY (B.DVD)
COVER (TRAY.R)
LEVER (SUB.L)
LEVER (SUB.R)
513
4-228-987-02 RACK (TRAY.R)
Remark
DVP-S9
Ver 1.4
7-5. CD MECHANISM DECK SECTION-2
(CDM63D)
551
557
558
551
556
not supplied
555
556
554
553
559
551
552
560
551
561
551
551
551
not
supplied
551
not supplied
551
562
CD mechanism deck section-3
Ref. No.
Part No.
Description
551
552
553
554
555
4-218-253-01
4-228-970-22
4-228-970-12
4-228-970-02
4-228-963-01
SCREW (M2.6), +BTTP
TRAY (SUB)
TRAY (SUB)
TRAY (SUB)
SLIDER (STOCKER.L)
556
4-228-981-02 STOPPER (TRAY)
Remark
Ref. No.
Part No.
Description
557
558
559
560
561
4-234-423-01
4-228-980-01
4-228-964-01
4-229-001-01
1-678-457-11
SPRING (STOCKER L), LEAF
SPRING (STOCKER), LEAF
SLIDER (STOCKER.R)
HOLDER (SENSOR)
TRAY SENSOR BOARD
562
4-228-993-05 SLIDER (LOADING)
Remark
61
DVP-S9
7-6. CD MECHANISM DECK SECTION-3
(CDM63D)
609
610
608
611
612
611
613
605
optical pick-up
section
607
615
605
614
606
not
supplied
616
601
605
603
602
604
605
617
604
601
not supplied
CD mechanism deck section-4
not supplied
Ref. No.
Part No.
Description
601
602
603
604
4-218-253-71
4-229-000-02
4-228-999-02
4-228-969-02
SCREW (M2.6), +BTTP
LEVER (MAIN.R)
LEVER (MAIN.L)
SPRING (TABLE), LEAF
605
606
607
608
609
4-218-253-01
4-985-672-01
4-228-977-01
1-678-463-11
4-231-520-01
SCREW (M2.6), +BTTP
SCREW (+PTPWH M2.6), FLOATING
SLIDER (BU.L)
DISK SENSOR BOARD
HOLDER (BU DVD)
62
Remark
Ref. No.
606
Part No.
Description
610
611
612
613
614
4-228-968-01
4-218-254-21
4-229-003-01
4-228-997-02
4-228-985-01
BELT
SCREW (M2.6), +PTPWH
PULLEY
GEAR (CAM)
GEAR (PULLEY)
615
616
617
4-228-976-01 SLIDER (BU.R)
1-678-460-11 DRIVER BOARD
4-218-253-61 SCREW (M2.6), +BTTP
Remark
DVP-S9
7-7. CD MECHANISM DECK SECTION-4
(CDM63D)
658
657
651
653
659
655
656
652
M721
654
653
651
661
651
652
657
651
Ref. No.
Part No.
Description
651
652
653
654
655
4-985-672-01
4-229-002-02
4-218-254-21
4-228-971-01
4-228-974-02
SCREW (+PTPWH M2.6), FLOATING
GEAR (SLIDER)
SCREW (M2.6), +PTPWH
CAM
RACK (CENTER)
656
4-228-988-01 CHASSIS
Remark
Ref. No.
657
658
659
661
M721
Part No.
Description
4-218-253-01
1-678-462-11
4-228-998-01
1-678-461-11
X-4952-971-2
SCREW (M2.6), +BTTP
IN OUT SW BOARD
GEAR (DETECTION)
MOTOR BOARD
MOTOR ASSY (LOADING)
Remark
63
DVP-S9
Ver 1.5
7-8. OPTICAL PICK-UP SECTION
• Refer to servicing notes (page 4) for discrimination of TYPE A/B.
705
704
704
706
707
704
708
703
701
709
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
701
703
704
705
0 706
A-4727-278-A
1-823-610-11
3-053-847-01
4-981-923-01
8-820-144-06
RF BOARD, COMPLETE
WIRE (FLAT TYPE) (26 CORE)
INSULATOR
SCREW (M), STEP
OPTICAL PICK-UP KHM-240AAA/J1RP
(TYPE A)
64
Remark
Ref. No.
Part No.
Description
Remark
0 706
707
708
709
A-6062-709-A
4-236-450-01
4-236-467-01
4-951-620-01
SERVICE ASSY, KHM-270AAA (TYPE B)
SCREW (L), STEP
BASE (DVD), FITTING
SCREW (2.6X8), BVTP
DVP-S9
Ver 1.5
SECTION 8
ELECTRICAL PARTS LIST
DISC SENSOR
DRIVER
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Refer to servicing notes (page 4) for discrimination of TYPE A/B.
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• Abbreviation
• CAPACITORS
AUS : Australian model
uF: µF
EA : Saudi Arabia model
• COILS
KR : Korean model
uH: µH
Description
Remark
Ref. No.
1-678-463-11 DISC SENSOR BOARD
******************
Part No.
MAIN
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
MX : Mexican model
SP : Singapore model
TH : Thai model
Description
Remark
1-678-462-11 IN OUT SW BOARD
****************
< PHOTO REFLECTOR >
IC751
IN OUT SW
< SWITCH >
8-749-924-30 PHOTO REFLECTOR GP2S28
(DISC IN DETECT)
S741
1-771-821-11 SWITCH, PUSH (1 KEY) (IN)
S742
1-771-821-11 SWITCH, PUSH (1 KEY) (OUT)
**************************************************************
< RESISTOR >
A-4727-237-A MAIN BOARD, COMPLETE
*********************
R751
1-249-407-11 CARBON
150
5%
1/4W
**************************************************************
< CAPACITOR >
1-678-460-11 DRIVER BOARD
*************
< CAPACITOR >
C701
C705
C706
C707
1-124-261-00
1-124-261-00
1-164-159-11
1-164-159-11
ELECT
ELECT
CERAMIC
CERAMIC
10uF
10uF
0.1uF
0.1uF
20%
20%
50V
50V
50V
50V
< CONNECTOR >
CN701
CN702
CN703
CN704
CN705
1-785-324-11
1-785-328-11
1-785-331-11
1-785-329-11
1-785-329-21
PIN, CONNECTOR (STRAIGHT) 12P
PIN, CONNECTOR (LIGHT ANGLE) 2P
PIN, CONNECTOR (LIGHT ANGLE) 5P
PIN, CONNECTOR (LIGHT ANGLE) 3P
PIN, CONNECTOR (LIGHT ANGLE) 3P
C101
C102
C401
C402
C403
1-164-159-11
1-164-159-11
1-126-934-11
1-126-934-11
1-164-159-11
CERAMIC
CERAMIC
ELECT
ELECT
CERAMIC
0.1uF
0.1uF
220uF
220uF
0.1uF
C404
C405
C406
C407
C408
1-164-159-11
1-164-159-11
1-126-934-11
1-126-934-11
1-164-159-11
CERAMIC
CERAMIC
ELECT
ELECT
CERAMIC
0.1uF
0.1uF
220uF
220uF
0.1uF
C411
C425
C427
C500
C501
1-164-159-11
1-162-282-31
1-162-282-31
1-164-159-11
1-126-768-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
ELECT
0.1uF
100PF
100PF
0.1uF
2200uF
C502
C504
C505
C506
C507
1-126-935-11
1-164-159-11
1-164-159-11
1-164-159-11
1-164-159-11
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
470uF
0.1uF
0.1uF
0.1uF
0.1uF
20%
10V
50V
50V
50V
50V
C508
C509
C512
C513
C514
1-126-964-11
1-126-935-11
1-164-159-11
1-126-935-11
1-126-947-11
ELECT
ELECT
CERAMIC
ELECT
ELECT
10uF
470uF
0.1uF
470uF
47uF
20%
20%
50V
10V
50V
10V
10V
C557
1-164-159-11 CERAMIC
0.1uF
20%
20%
20%
20%
10%
10%
20%
50V
50V
10V
10V
50V
50V
50V
10V
10V
50V
50V
50V
50V
50V
16V
< IC >
IC701
8-759-598-69 IC BA6956AN
< TRANSISTOR >
Q701
8-729-029-66 TRANSISTOR
RT1N141S-TP
< RESISTOR >
R701
1-249-429-11 CARBON
10K
5%
1/4W
R702
1-249-401-11 CARBON
47
5%
1/4W
R705
1-249-435-11 CARBON
33K
5%
1/4W
R706
1-249-417-11 CARBON
1K
5%
1/4W
R707
1-249-429-11 CARBON
10K
5%
1/4W
**************************************************************
20%
20%
50V
< CONNECTOR >
* CN101
CN102
CN103
1-568-419-11 PIN, CONNECTOR 9P
1-568-373-11 PIN, CONNECTOR 8P
1-566-859-11 SOCKET, CONNECTOR 15P
(SYSTEM CONTROL 5 FROM TC-S9)
65
DVP-S9
MAIN
MB
Ref. No.
Part No.
CN107
* CN401
1-779-278-11 CONNECTOR, FFC (LIF (NON-ZIF)) 10P
1-568-936-11 PIN, CONNECTOR 9P
Description
Remark
CN501
* CN503
1-506-469-11 PIN, CONNECTOR 4P
1-568-937-11 PIN, CONNECTOR 10P
< DIODE >
D105
D501
D502
D503
D504
8-719-911-19
8-719-024-99
8-719-024-99
8-719-024-99
8-719-024-99
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-72
11ES2-NTA2B
11ES2-NTA2B
11ES2-NTA2B
11ES2-NTA2B
D505
D512
D513
D514
8-719-911-19
8-719-024-99
8-719-024-99
8-719-024-99
DIODE
DIODE
DIODE
DIODE
1SS133T-72
11ES2-NTA2B
11ES2-NTA2B
11ES2-NTA2B
< FERRITE BEAD >
FB501
FB502
FB503
1-412-473-21 FERRITE BEAD
1-412-473-21 FERRITE BEAD
1-412-473-21 FERRITE BEAD
< IC >
IC401
IC501
IC502
6-800-720-01 IC M30622MAA-B33FP
8-759-071-48 IC TA7807S
8-759-604-35 IC M5F78M05L
< CONNECTOR >
* NO104
Ref. No.
Part No.
Description
Remark
R443
R444
R447
1-249-409-11 CARBON
1-249-409-11 CARBON
1-249-409-11 CARBON
220
220
220
5%
5%
5%
1/4W
1/4W
1/4W
R448
R451
R453
R454
R455
1-249-409-11
1-249-429-11
1-249-409-11
1-249-429-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
10K
220
10K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R456
R457
R459
R465
R469
1-249-429-11
1-249-429-11
1-249-409-11
1-249-407-11
1-249-407-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
220
150
150
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R473
R477
R480
R481
R482
1-249-407-11
1-249-407-11
1-249-441-11
1-249-407-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
150
150
100K
150
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R483
R484
R485
R486
R487
1-249-429-11
1-249-409-11
1-249-409-11
1-249-409-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
220
220
220
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R488
R489
R490
R491
R492
1-249-409-11
1-249-409-11
1-249-409-11
1-249-409-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
220
220
220
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R493
R494
R495
R496
R497
1-249-415-11
1-247-807-31
1-249-410-11
1-249-429-11
1-249-410-11
CARBON
CARBON
CARBON
CARBON
CARBON
680
100
270
10K
270
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R567
1-249-441-11 CARBON
100K
5%
1/4W
1-568-936-11 PIN, CONNECTOR 9P
< RESISTOR >
R101
R102
R103
R104
R132
1-247-807-31
1-247-807-31
1-249-417-11
1-247-807-31
1-247-876-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
1K
100
75K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R133
R134
R409
R411
R412
1-247-876-11
1-249-417-11
1-249-429-11
1-249-409-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
75K
1K
10K
220
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R413
R417
R419
R425
R427
1-249-411-11
1-249-429-11
1-249-409-11
1-249-425-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
330
10K
220
4.7K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R429
R430
R431
R432
R433
1-247-807-31
1-247-807-31
1-249-409-11
1-249-409-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
220
220
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R434
R435
R436
R437
R440
1-249-409-11
1-249-409-11
1-249-409-11
1-249-409-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
220
220
220
220
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R441
R442
1-249-429-11 CARBON
1-249-409-11 CARBON
10K
220
5%
5%
1/4W
1/4W
< VIBRATOR >
X401
1-781-107-21 VIBRATOR, CERAMIC (16MHz)
**************************************************************
A-4727-239-A
A-4727-244-A
A-4727-246-A
A-4727-248-A
A-4727-252-A
MB BOARD, COMPLETE (AEP, UK)
MB BOARD, COMPLETE (AUS)
MB BOARD, COMPLETE (E, MX)
MB BOARD, COMPLETE (EA)
MB BOARD, COMPLETE (KR, SP, TH)
********************
< CAPACITOR >
66
C004
C005
C006
C007
C018
1-126-204-11
1-126-246-11
1-126-204-11
1-162-915-11
1-107-826-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
220uF
47uF
10PF
0.1uF
20%
20%
20%
0.5PF
10%
16V
4V
16V
50V
16V
C019
C103
C104
C105
C106
1-107-826-11
1-162-970-11
1-126-209-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
100uF
0.01uF
0.01uF
10%
10%
20%
10%
10%
16V
25V
4V
25V
25V
C107
1-162-915-11 CERAMIC CHIP
10PF
0.5PF
50V
DVP-S9
MB
Ref. No.
Part No.
Description
C108
C109
C110
C111
1-162-917-11
1-162-970-11
1-126-209-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
15PF
0.01uF
100uF
0.01uF
5%
10%
20%
10%
Remark
50V
25V
4V
25V
C112
C113
C114
C116
C119
1-107-826-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
16V
25V
25V
25V
25V
C124
C202
C203
C204
C205
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C206
C207
C301
C304
C305
1-162-970-11
1-162-970-11
1-107-826-11
1-126-246-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.1uF
220uF
0.01uF
10%
10%
10%
20%
10%
25V
25V
16V
4V
25V
C306
C307
C309
C310
C311
1-162-968-11
1-162-970-11
1-162-968-11
1-162-968-11
1-162-968-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.01uF
0.0047uF
0.0047uF
0.0047uF
10%
10%
10%
10%
10%
50V
25V
50V
50V
50V
C312
C313
C315
C317
C318
1-107-826-11
1-164-677-11
1-162-927-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.033uF
100PF
0.01uF
0.01uF
10%
10%
5%
10%
10%
16V
16V
50V
25V
25V
C319
C320
C321
C322
C323
1-110-563-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.068uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
16V
25V
25V
25V
25V
C324
C325
C326
C327
C328
1-162-970-11
1-162-970-11
1-162-970-11
1-107-826-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.1uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
16V
25V
C331
C332
C333
C334
C335
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C336
C337
C338
C339
C340
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C341
C342
C343
C344
C345
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C346
C347
C348
C349
1-162-968-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
50V
25V
25V
25V
Ref. No.
Part No.
Description
Remark
C350
1-162-970-11 CERAMIC CHIP
0.01uF
10%
25V
C351
C352
C401
C402
C403
1-162-970-11
1-126-204-11
1-164-245-11
1-162-960-11
1-162-927-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
47uF
0.015uF
220PF
100PF
10%
20%
10%
10%
5%
25V
16V
25V
50V
50V
C404
C405
C406
C407
C408
1-162-965-11
1-107-826-11
1-107-826-11
1-162-960-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0015uF
0.1uF
0.1uF
220PF
100PF
10%
10%
10%
10%
5%
50V
16V
16V
50V
50V
C411
C412
C413
C414
C415
1-162-968-11
1-164-677-11
1-164-677-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.033uF
0.033uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
50V
16V
16V
25V
25V
C416
C417
C418
C419
C420
1-162-970-11
1-162-964-11
1-162-970-11
1-126-204-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.01uF
0.001uF
0.01uF
47uF
0.1uF
10%
10%
10%
20%
10%
25V
50V
25V
16V
16V
C429
C430
C501
C502
C503
1-162-964-11
1-162-964-11
1-126-193-11
1-117-370-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
1uF
10uF
0.01uF
10%
10%
20%
50V
50V
50V
10V
25V
C504
C505
C506
C508
C509
1-162-970-11
1-117-370-11
1-117-370-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
10uF
0.01uF
0.01uF
10%
10%
10%
25V
10V
10V
25V
25V
C510
C511
C512
C513
C514
1-162-970-11
1-162-970-11
1-126-246-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
220uF
0.01uF
0.01uF
10%
10%
20%
10%
10%
25V
25V
4V
25V
25V
C516
C518
C519
C520
C521
1-162-970-11
1-107-826-11
1-162-970-11
1-162-970-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.01uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
25V
16V
25V
25V
16V
C522
C523
C524
C525
C526
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C529
C530
C531
C532
C533
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C534
C535
C536
C537
C538
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C539
1-162-970-11 CERAMIC CHIP
0.01uF
10%
25V
10%
67
DVP-S9
Ver 1.5
MB
Ref. No.
Part No.
Description
C540
C541
C542
C545
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
25V
25V
25V
25V
Remark
C546
C547
C701
C702
C711
1-162-970-11
1-162-970-11
1-126-206-11
1-107-826-11
1-162-918-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
100uF
0.1uF
18PF
10%
10%
20%
10%
5%
25V
25V
6.3V
16V
50V
C712
C716
C717
C721
C722
1-162-921-11
1-162-918-11
1-162-921-11
1-162-918-11
1-162-921-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
33PF
18PF
33PF
18PF
33PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C741
C742
C743
C744
C745
1-107-826-11
1-126-206-11
1-124-778-00
1-126-206-11
1-124-778-00
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
0.1uF
100uF
22uF
100uF
22uF
10%
20%
20%
20%
20%
16V
6.3V
6.3V
6.3V
6.3V
C764
C765
C766
1-126-193-11 ELECT
1-126-193-11 ELECT
1-126-193-11 ELECT
1uF
1uF
1uF
20%
20%
20%
50V
50V
50V
< CONNECTOR >
CN008
CN010
CN012
CN015
CN101
CN103
* CN203
CN404
1-779-992-11
1-784-875-21
1-784-860-21
1-784-368-11
1-784-369-21
PIN, CONNECTOR (PWB) 8P
CONNECTOR, FFC (LIF (NON-ZIF)) 25P
CONNECTOR, FFC (LIF (NON-ZIF)) 8P
CONNECTOR, FFC/FPC 9P
CONNECTOR, FFC/FPC 10P
Part No.
FB007
FB008
FB009
FB010
FB011
1-469-324-21
1-469-324-21
1-469-324-21
1-469-324-21
1-469-324-21
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FB012
FB112
FB711
FB712
FB714
1-469-324-21
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
FERRITE BEAD
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
< EMI FILTER >
FL003
FL004
FL005
FL101
FL102
1-234-177-21
1-234-177-21
1-233-893-21
1-233-893-21
1-233-893-21
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FL103
FL202
FL203
FL204
FL501
1-233-893-21
1-233-893-21
1-233-893-21
1-234-177-21
1-233-893-21
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FL502
FL505
1-233-893-21 FILTER, CHIP EMI
1-234-177-21 FILTER, CHIP EMI
0
0
0
0
5%
5%
5%
5%
Description
Remark
< IC >
IC006
IC101
IC102
IC103
IC106
6-700-398-01
8-759-640-41
8-759-831-81
8-759-829-75
8-759-645-76
IC
IC
IC
IC
IC
uPC2918T-E1
BR24C08F-E2
IMIC6001BTD
MB91307APFV-G-BND-E1
TC74VHCT32AFT
IC107
IC202
IC301
IC302
IC303
8-759-826-41
6-700-740-01
8-759-599-45
8-759-828-01
8-759-683-75
IC
IC
IC
IC
IC
MBM29DL324BE-90PFTN
LC22004A-RJ6-TBM-E
MM1385ENLE
CXD9635R
MSM51V18160F-60TSKR1
IC401
IC501
IC502
IC503
IC504
8-759-826-42
8-759-832-30
8-759-599-45
8-752-399-55
8-759-663-74
IC
IC
IC
IC
IC
FAN8034
TK71518ASCL
MM1385ENLE
CXD1933Q
HY57V161610DTC-7TR
IC505
IC701
8-759-663-74 IC HY57V161610DTC-7TR
8-759-680-28 IC BA7666FS-E2
< COIL >
L701
L711
L713
L715
1-412-788-41
1-412-790-31
1-412-790-31
1-412-790-31
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
15uH
15uH
15uH
< TRANSISTOR >
Q711
Q712
8-729-027-23 TRANSISTOR
1-801-806-11 TRANSISTOR
1-793-687-11 PIN, CONNECTOR (1.5mm) (SMD) 5P
1-764-007-11 PIN, CONNECTOR (SMD) 12P
1-793-687-11 PIN, CONNECTOR (1.5mm) (SMD) 5P
DTA114EKA-T146
DTC144EKA-T146
< RESISTOR >
< FERRITE BEAD/RESISTOR >
68
Ref. No.
1/16W
1/16W
1/16W
1/16W
R017
R021
R076
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
1-216-837-11 METAL CHIP
0
0
22K
5%
5%
5%
1/16W
1/16W
1/16W
(TYPE A)
1/16W
(TYPE A)
1/16W
(TYPE B)
R077
1-216-815-11 METAL CHIP
330
5%
R077
1-216-833-11 METAL CHIP
10K
5%
R078
R080
R101
R105
R106
1-216-827-11
1-216-801-11
1-216-789-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
22
2.2
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R107
R109
R111
R112
R113
1-216-821-11
1-216-797-11
1-216-817-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10
470
1K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R114
R116
R117
R118
R119
1-216-845-11
1-216-833-11
1-216-821-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
10K
1K
1K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R121
R123
R124
R125
1-216-833-11
1-216-833-11
1-216-797-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10
10
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
DVP-S9
MB
Ref. No.
Part No.
Description
Remark
R126
1-216-797-11 METAL CHIP
10
5%
1/16W
R128
R129
R130
R131
R132
1-216-827-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R133
R134
R136
R137
R138
1-216-833-11
1-216-833-11
1-216-797-11
1-216-797-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10
10
10
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R140
R141
R142
R143
R145
1-216-797-11
1-216-797-11
1-216-797-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
10
10
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R146
R147
R149
R150
1-216-833-11
1-216-825-11
1-216-829-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
2.2K
4.7K
1K
5%
5%
5%
5%
R150
1-216-827-11 METAL CHIP
3.3K
5%
1/16W
1/16W
1/16W
1/16W
(EA)
1/16W
(AUS)
R150
1-216-831-11 METAL CHIP
6.8K
5%
R150
1-216-835-11 METAL CHIP
15K
5%
R150
1-216-839-11 METAL CHIP
33K
5%
R151
R152
1-216-829-11 METAL CHIP
1-216-833-11 METAL CHIP
4.7K
10K
5%
5%
R153
R154
1-216-829-11 METAL CHIP
1-216-835-11 METAL CHIP
4.7K
15K
5%
5%
R154
1-216-839-11 METAL CHIP
33K
R154
1-216-843-11 METAL CHIP
68K
R155
1-216-829-11 METAL CHIP
4.7K
1/16W
1/16W
(AUS, E, MX)
5%
1/16W
(KR, SP, TH)
5%
1/16W
(AEP, EA, UK)
5%
1/16W
R156
R157
R160
R161
R162
1-216-833-11
1-216-864-11
1-216-833-11
1-216-864-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
10K
0
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R163
R164
R165
R166
R167
1-216-833-11
1-216-809-11
1-216-809-11
1-216-829-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
100
4.7K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R168
R170
R172
R174
R175
1-216-821-11
1-216-821-11
1-216-833-11
1-216-797-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
10
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R179
R182
R183
R184
R185
1-216-833-11
1-216-845-11
1-216-829-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
4.7K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
(KR, SP, TH)
1/16W
(AEP, UK)
1/16W
(E, MX)
1/16W
1/16W
Ref. No.
Part No.
Description
Remark
R186
R187
R188
R199
R202
1-216-833-11
1-216-825-11
1-216-833-11
1-216-826-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
2.2K
10K
2.7K
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R203
R206
R207
R208
R209
1-216-821-11
1-216-813-11
1-216-813-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
220
220
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R210
R211
R212
R214
R215
1-216-821-11
1-216-821-11
1-216-821-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R299
R301
R302
R305
R306
1-216-847-11
1-216-827-11
1-216-827-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
150K
3.3K
3.3K
4.7K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R307
R308
R309
R310
R311
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R312
R313
R314
R315
R316
1-216-829-11
1-216-817-11
1-216-817-11
1-216-817-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
470
470
470
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R317
R318
R319
R320
R321
1-216-833-11
1-216-864-11
1-216-831-11
1-216-864-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
6.8K
0
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R328
R329
R330
R332
R334
1-216-833-11
1-216-864-11
1-216-864-11
1-216-864-11
1-218-871-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
0
0
10K
5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/10W
R335
R336
R337
R338
R341
1-218-855-11
1-216-833-11
1-216-809-11
1-218-879-11
1-218-871-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
10K
100
22K
10K
0.5%
5%
5%
0.5%
0.5%
1/10W
1/16W
1/16W
1/10W
1/10W
R342
R343
R344
R345
R349
1-218-883-11
1-218-831-11
1-218-847-11
1-216-833-11
1-216-838-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
220
1K
10K
27K
0.5%
0.5%
0.5%
5%
5%
1/10W
1/10W
1/10W
1/16W
1/16W
R350
R351
R352
R356
R368
1-216-822-11
1-216-825-11
1-216-825-11
1-218-853-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.2K
2.2K
2.2K
1.8K
4.7K
5%
5%
5%
0.5%
5%
1/16W
1/16W
1/16W
1/10W
1/16W
R384
R385
1-216-797-11 METAL CHIP
1-216-829-11 METAL CHIP
10
4.7K
5%
5%
1/16W
1/16W
69
DVP-S9
MB
Ref. No.
MOTOR
Part No.
PANEL
Description
Remark
R406
R407
R408
1-216-846-11 METAL CHIP
1-216-846-11 METAL CHIP
1-216-847-11 METAL CHIP
120K
120K
150K
5%
5%
5%
1/16W
1/16W
1/16W
R409
R410
R411
R412
R413
1-216-847-11
1-216-842-11
1-216-842-11
1-216-850-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
150K
56K
56K
270K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R414
R415
R416
R417
R418
1-216-853-11
1-216-846-11
1-216-855-11
1-216-833-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
120K
680K
10K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R419
R420
R421
R422
R423
1-216-839-11
1-216-853-11
1-216-839-11
1-216-839-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
470K
33K
33K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R424
R425
R426
R427
R428
1-216-839-11
1-216-849-11
1-216-853-11
1-218-895-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
220K
470K
100K
33K
5%
5%
5%
0.5%
5%
1/16W
1/16W
1/16W
1/10W
1/16W
R429
R430
R431
R432
R433
1-218-889-11
1-218-895-11
1-218-889-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
56K
100K
56K
10K
10K
0.5%
0.5%
0.5%
5%
5%
1/10W
1/10W
1/10W
1/16W
1/16W
R434
R435
R439
R507
R508
1-216-815-11
1-216-833-11
1-216-864-11
1-216-809-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
10K
0
100
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R509
R510
R511
R512
R513
1-216-864-11
1-216-833-11
1-216-813-11
1-216-813-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
10K
220
220
220
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R514
R515
R516
R517
R518
1-216-813-11
1-216-813-11
1-216-813-11
1-216-833-11
1-216-822-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
220
220
10K
1.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R521
R522
R524
R525
R532
1-216-864-11
1-216-827-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
3.3K
10K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R533
R554
R701
R711
R712
1-216-797-11
1-216-797-11
1-216-833-11
1-218-289-11
1-218-289-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
10
10
10K
510
510
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R713
R717
R718
R719
R724
1-218-289-11
1-218-285-11
1-218-285-11
1-218-285-11
1-216-833-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
510
75
75
75
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
Ref. No.
R725
R737
R738
R739
R740
Description
1-216-833-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
Remark
10K
0
0
0
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< VARIABLE RESISTOR >
RV501
70
Part No.
1-223-583-11 RES, ADJ, CARBON 1K
< VIBRATOR >
X101
1-795-174-11 VIBRATOR, CERAMIC (16.5MHz)
X102
1-767-519-11 VIBRATOR, CRYSTAL (27MHz)
**************************************************************
1-678-461-11 MOTOR BOARD
*************
< CAPACITOR >
C721
1-162-306-11 CERAMIC
0.01uF
30%
16V
**************************************************************
1-682-812-11 PANEL BOARD
************
< DIODE >
D701
D702
D703
D704
D705
8-719-057-97
8-719-058-03
8-719-057-97
8-719-057-97
8-719-057-97
LED
LED
LED
LED
LED
SEL5923A-TP15 (X)
SEL5423E-TP15 (N)
SEL5923A-TP15 (3 (DISC 3))
SEL5923A-TP15 (2 (DISC 2))
SEL5923A-TP15 (1 (DISC 1))
< RESISTOR >
R711
R712
R713
R714
R715
1-249-411-11
1-249-413-11
1-249-414-11
1-249-415-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
330
470
560
680
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R716
R717
R718
R719
1-249-418-11
1-249-420-11
1-249-422-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
1.2K
1.8K
2.7K
3.3K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
< SWITCH >
S711
S712
S713
S714
S715
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
SWITCH, TACTILE (m)
SWITCH, TACTILE (M)
SWITCH, TACTILE (>)
SWITCH, TACTILE (.)
SWITCH, TACTILE (x)
S716
1-771-410-21 SWITCH, TACTILE (X)
S717
1-771-410-21 SWITCH, TACTILE (N)
S718
1-771-410-21 SWITCH, TACTILE (RETURN)
S719
1-771-410-21 SWITCH, TACTILE (PREV)
S720
1-771-410-21 SWITCH, TACTILE (NEXT)
**************************************************************
DVP-S9
Ver 1.2
RF
Ref. No.
Part No.
Description
Remark
Ref. No.
SUB PANEL
Part No.
A-4727-278-A RF BOARD, COMPLETE
********************
Description
Remark
< RESISTOR >
< CAPACITOR >
C001
C002
C005
C006
C007
1-162-970-11
1-162-970-11
1-162-966-11
1-162-966-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.0022uF
0.0022uF
0.0022uF
10%
10%
10%
10%
10%
25V
25V
50V
50V
50V
C008
C009
C015
C016
C017
1-162-966-11
1-124-779-00
1-162-968-11
1-162-968-11
1-126-206-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.0022uF
10uF
0.0047uF
0.0047uF
100uF
10%
20%
10%
10%
20%
50V
16V
50V
50V
6.3V
C018
C019
C021
C022
C023
1-115-416-11
1-164-739-11
1-124-779-00
1-107-826-11
1-126-206-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
0.001uF
560PF
10uF
0.1uF
100uF
5%
5%
20%
10%
20%
25V
50V
16V
16V
6.3V
C024
C025
C026
C027
C028
1-115-416-11
1-107-826-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
0.01uF
0.01uF
0.01uF
5%
10%
10%
10%
10%
25V
16V
25V
25V
25V
C031
C032
C033
C034
C035
1-107-826-11
1-107-826-11
1-162-964-11
1-162-970-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.001uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
50V
25V
16V
C036
C038
C039
C040
C043
1-165-176-11
1-165-176-11
1-162-970-11
1-164-217-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.047uF
0.01uF
150PF
0.1uF
10%
10%
10%
5%
10%
16V
16V
25V
50V
16V
C044
C046
C047
C048
1-124-779-00
1-162-970-11
1-107-826-11
1-162-970-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.01uF
0.1uF
0.01uF
20%
10%
10%
10%
16V
25V
16V
25V
< CONNECTOR >
CN001
CN002
TRAY SENSOR
R002
R003
R005
R006
R007
1-216-809-11
1-216-809-11
1-216-845-11
1-216-838-11
1-216-803-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100K
27K
33
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R008
R009
R010
R011
R020
1-216-803-11
1-216-821-11
1-216-841-11
1-216-809-11
1-216-803-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33
1K
47K
100
33
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R023
R025
R029
R037
R038
1-216-803-11
1-216-841-11
1-216-809-11
1-216-834-11
1-216-861-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33
47K
100
12K
2.2M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R045
1-216-809-11 METAL CHIP
100
5%
1/16W
**************************************************************
1-682-814-11 SUB PANEL BOARD
*****************
R701
R702
R703
R704
R705
1-249-411-11
1-249-413-11
1-249-414-11
1-249-415-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
R706
R707
1-249-418-11 CARBON
1-249-420-11 CARBON
330
470
560
680
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
1.2K
1.8K
5%
5%
1/4W
1/4W
< SWITCH >
S701
S702
S703
S704
S705
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
SWITCH, TACTILE (DISC 3)
SWITCH, TACTILE (DISC 2)
SWITCH, TACTILE (DISC 1)
SWITCH, TACTILE (Z (DISC 1))
SWITCH, TACTILE (Z (DISC 2))
S706
1-771-410-21 SWITCH, TACTILE (Z (DISC 3))
S707
1-771-410-21 SWITCH, TACTILE (REPEAT)
S708
1-771-410-21 SWITCH, TACTILE (PLAY MODE)
**************************************************************
1-766-835-21 CONNECTOR, FFC/FPC (ZIF) 26P
1-784-875-21 CONNECTOR, FFC (LIF (NON-ZIF)) 25P
1-678-457-11 TRAY SENSOR BOARD
*******************
< DIODE >
< CAPACITOR >
D001
D004
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
C731
L001
L002
IC731
8-759-828-02 IC SP3728AC
< COIL >
IC732
1-412-031-11 INDUCTOR CHIP 47uH
1-412-031-11 INDUCTOR CHIP 47uH
IC733
8-729-903-46 TRANSISTOR
8-729-903-46 TRANSISTOR
50V
8-749-016-76 PHOTO SENSOR RPI-321
(SUB TRAY 1 HEIGHT SENSOR)
8-749-016-76 PHOTO SENSOR RPI-321
(SUB TRAY 2 HEIGHT SENSOR)
8-749-016-76 PHOTO SENSOR RPI-321
(SUB TRAY 3 HEIGHT SENSOR)
< RESISTOR >
< TRANSISTOR >
Q001
Q002
0.1uF
< PHOTO SENSOR >
< IC >
IC001
1-164-159-11 CERAMIC
2SB1132-T100-QR
2SB1132-T100-QR
R731
R732
1-247-876-11 CARBON
1-249-408-11 CARBON
75K
180
5%
5%
1/4W
1/4W
71
DVP-S9
Ver 1.5
TRAY SENSOR
Ref. No.
R733
R734
R735
Part No.
VIDEO
Description
1-247-876-11 CARBON
1-249-408-11 CARBON
1-247-876-11 CARBON
Remark
75K
180
75K
5%
5%
5%
Ref. No.
Part No.
Description
Remark
1/4W
1/4W
1/4W
R736
1-249-408-11 CARBON
180
5%
1/4W
**************************************************************
A-4727-238-A VIDEO BOARD, COMPLETE
**********************
< CAPACITOR >
C203
C204
C206
1-164-159-11 CERAMIC
1-126-934-11 ELECT
1-164-159-11 CERAMIC
0.1uF
220uF
0.1uF
20%
50V
10V
50V
< CONNECTOR >
CN201
CN202
1-779-276-11 CONNECTOR, FFC (LIF (NON-ZIF)) 8P
1-568-951-11 PIN, CONNECTOR 2P
< FERRITE BEAD >
FB201
FB202
FB203
FB204
1-412-473-21
1-412-473-21
1-412-473-21
1-412-473-21
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
< IC >
IC201
8-749-923-04 IC TOTX178A (OPTICAL OUT TO ST-S9)
< JACK >
J201
J202
1-537-943-11 CONNECTOR (DIN) 1P (S VIDEO OUT)
1-794-970-11 JACK, PIN 1P (VIDEO OUT)
< COIL >
L201
1-410-525-11 INDUCTOR
220uH
**************************************************************
MISCELLANEOUS
**************
01
01
01
05
05
1-476-027-11
1-476-028-11
1-476-029-11
1-823-394-11
1-823-396-11
POWER BLOCK (AUS, EA, SP, TH)
POWER BLOCK (AEP, KR, UK)
POWER BLOCK (E, MX)
CORD, POWER (E, MX)
CORD, POWER (AEP, AUS, EA, SP, TH, UK)
05
101
104
107
108
1-823-399-11
1-823-609-11
1-823-608-11
1-823-607-11
1-757-633-11
CORD, POWER (KR)
WIRE (FLAT TYPE) (25 CORE)
WIRE (FLAT TYPE) (10 CORE)
WIRE (FLAT TYPE) (8 CORE)
CORD (WITH CONNECTOR) 17P
702
703
0 706
1-823-611-11 WIRE (FLAT TYPE) (9 CORE)
1-823-610-11 WIRE (FLAT TYPE) (26 CORE)
8-820-144-06 OPTICAL PICK-UP KHM-240AAA/J1RP
(TYPE A)
A-6062-709-A SERVICE ASSY, KHM-270AAA (TYPE B)
1-532-388-31 MINIATURE FUSE-LINKS, TIME-LAG FUSE
(T2AL/250V)
0 706
0 F1
M721
72
X-4952-971-2 MOTOR ASSY (LOADING)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
DVP-S9
MEMO
73
DVP-S9
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
1.0
1.1
1.2
Date
2001.09
2002.03
2002.10
Description of Revision
New
Addition of service position
(SPM-02009)
Change of Part No. for IC731, 732, 733 on TRAY SENSOR board
(SPM-02085)
1.3
2002.11
Addition of Ref. No. 508, 511, 512, 513 to EXPLODED VIEWS
(SPM-02098)
1.4
1.5
1.6
2002.12
2003.01
2003.03
1.7
2004.09
Addition of Ref. No. 562 to EXPLODED VIEWS
(SPM-02116)
Change of OPTICAL PICK-UP
(SPM-02121)
Addition of “TEST MODE” to the TEST MODE
Addition of “AUTO SERVO ADJUSTMENT” to the ELECTRICAL
ADJUSTMENTS
(SPM-03008)
Addition of “NOTE OF REPLACING THE MB BOARD” to SERVICING NOTES
(SPM-04038)