Download GDM-5403 - Wiki Karat
Transcript
GDM-5403 SERVICE MANUAL AEP Model Chassis No. SCC-L22M-A (OEM STD) Chassis No. SCC-L22U-A (ELSA, FORMAC) G1 CHASSIS SPECIFICATIONS CRT Viewable image size Maximum resolution Standard image area Deflection frequency* AC input voltage/current 0.24 mm aperture grille pitch 21 inches measured diagonally 90-degree deflection FD Trinitron Approx. 403.8 × 302.2 mm (w/h) (16 × 12 inches) 19.8" viewing image Horizontal: 1600 dots Vertical: 1200 lines Approx. 388 × 291 mm (w/h) (15 3/8 × 11 1/2 inches) or Approx. 364 × 291 mm (w/h) (14 3/8 × 11 1/2 inches) Horizontal: 30 to 109 kHz Vertical: 48 to 160 Hz 100 to 240 V, 50 – 60 Hz, 2.0 – 1.0 A Power consumption Dimensions Mass Plug and Play Approx. 145 W Approx. 498 × 491 × 478 mm (w/h/d) (19 5/8 × 19 3/8 × 18 7/8 inches) Approx. 32 kg (70 lb 9 oz) DDC1/2B/2Bi, GTF** * Recommended horizontal and vertical timing condition • Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. • Horizontal blanking width should be more than 2.3 µsec. • Vertical blanking width should be more than 450 µsec. ** If the input signal is Generalized Timing Formula (GTF) compliant, the GTF feature of the monitor will automatically provide an optimal image for the screen. Design and specifications are subject to change without notice. COLOR GRAPHIC DISPLAY GDM-5403 SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7. Check the B+ and HV to see if they are specified values. Make sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV. 8. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC Leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOMs that are suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 0.15 µF 1.5 kΩ AC Voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. WARNING!! NEVER TURN ON THE POWER IN A CONDITION IN WHICH THE DEGAUSS COIL HAS BEEN REMOVED. CAUTION ON DAS (ECS) CONNECTOR • The connector for DAS (ECS) adjustment is provided inside the cover shown below. Be careful with an electrical shock when connecting the connector with the power supplied. Also, return the removed cover to the home position. Rear side Cover ECS SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY SHADING AND MARK ¡ ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED. –2– GDM-5403 POWER SAVING FUNCTION This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in three stages as shown below. Power mode Power consumption 1 (power) indicator normal operation ≤ 145 W green 1 standby ≤ 100 W green and orange alternate 2 suspend (sleep)* ≤ 15 W green and orange alternate 3 active off** (deep sleep)* Approx. 1 W orange power off 0W off * “Sleep” and “deep sleep” are power saving modes defined by the Environmental Protection Agency. ** When your computer enters a power saving mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters power saving mode. DIAGNOSIS If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cables and check the condition of your computer(s). This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer(s), the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard. If the color bars do not appear, there is a potential monitor failure. Inform your service representative of the monitor’s condition. If the 1 (power) indicator is flashing orange 1 2 Press the 1 (power) button twice to turn the monitor off and then on. If the 1 (power) indicator lights up green, the monitor is working properly. 1 (power) indicator If the 1 (power) indicator is green If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your service representative of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and video board. 1 Disconnect the video input cable or turn off the connected computer. 2 Press the 1 (power) button twice to turn the monitor off and then on. 3 Press the , button for 2 seconds before the monitor enters power saving mode. –3– GDM-5403 TIMING SPECIFICATION MODE AT PRODUCTION MODE 1 MODE 2 RESOLUTION 1600 X 1200 1280 X 1024 CLOCK 229.500 MHz 157.500 MHz 106.250 kHz 91.146 kHz — HORIZONTAL — H-FREQ usec usec H. TOTAL 9.412 10.971 H. BLK 2.440 2.844 H. FP 0.279 0.406 H. SYNC 0.837 1.016 H. BP 1.325 1.422 H. ACTIV 6.972 8.127 85.000 Hz 85.024 Hz — VERTICAL — V. FREQ (HZ) ` lines lines V. TOTAL 1250 1072 V. BLK 50 48 V. FP 1 1 V. SYNC 3 3 V. BP 46 44 1200 1024 V. ACTIV — SYNC — INT(G) EXT (H/V) /POLARITY EXT (CS) /POLARITY INT/NON INT NO NO YES P/P YES P/P NO NO NON INT NON INT 2000.01.04 VER. –4– GDM-5403 TABLE OF CONTENTS Section Title Page 1. GENERAL ................................................................. 1-1 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. Cabinet Removal ............................................... D Board Removal .............................................. G Board Removal .............................................. A Board Terminal Board Bracket Removal ............................................................. 2-5. N Board Removal .............................................. 2-6. Service Position .................................................. 2-7. Bezel Assembly, H Board Removal .................. 2-8. J Board Removal ............................................... 2-9. Picture Tube Removal ....................................... 2-10. Harness Location ............................................... 2-1 2-1 2-2 2-2 2-3 2-3 2-4 2-4 2-5 2-6 3. SAFETY RELATED ADJUSTMENT ............. 3-1 4. ADJUSTMENTS ..................................................... 4-1 5. DIAGRAMS 5-1. 5-2. 5-3. 5-4. (1) (2) (3) (4) (5) 5-5. Block Diagrams .................................................. Frame Schematic Diagram ................................. Circuit Boards Location ..................................... Schematic Diagrams and Printed Wiring Boards ................................................................. Schematic Diagram of A Board ........................ Schematic Diagrams of H, J Boards ................. Schematic Diagram of D Board ........................ Schematic Diagrams of N (a, b, c) Board Schematic Diagram of G Board ........................ Semiconductors ................................................. 5-1 5-7 5-9 5-9 5-11 5-17 5-19 5-23 5-31 5-35 6. EXPLODED VIEWS 6-1. 6-2. 6-3. Chassis ............................................................... 6-1 Picture Tube ...................................................... 6-2 Packing Materials ............................................... 6-3 7. ELECTRICAL PARTS LIST ............................ 7-1 Note: Hand degauss must be used on stand-by or power-off condition. This model has an automatic earth magnetism correction function by using an earth magnetism sensor and a LCC coil. When using a hand degauss while monitor (LCC coil) is being operated, it sometimes gets magnetized, and the system may not work properly as a result. –5– The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual. SECTION 1 GENERAL Use of the tilt-swivel Precautions This monitor can be adjusted within the angles shown below. To turn the monitor vertically or horizontally, hold it at the bottom with both hands. Warning on power connections Use an appropriate power cord for your local power supply. Identifying parts and controls See the pages in parentheses for further details. Front Rear Example of plug types 90˚ AC IN 15˚ 90˚ (HD15) 1 for 100 to 120 V AC for 240 V AC only • Before disconnecting the power cord, wait at least 30 seconds after turning off the power to allow the static electricity on the screen’s surface to discharge. • After the power is turned on, the screen is demagnetized (degaussed) for about 2 seconds. This generates a strong magnetic field around the screen which may affect data stored on magnetic tapes and disks placed near the monitor. Be sure to keep magnetic recording equipment, tapes, and disks away from the monitor. The equipment should be installed near an easily accessible outlet. 5˚ 1 1 0 (reset) button (page 14) This button resets the adjustments to the factory settings. 7 AC IN connector (page 6) This connector provides AC power to the monitor. 2 ASC (auto sizing and centering) button (page 7) This button automatically adjusts the size and centering of the picture. 8 Video input connector (HD15) (y1) (page 6) This connector inputs RGB video signals (0.700 Vp-p, positive) and sync signals. 3 (brightness) m/M buttons (page 9) These buttons display the BRIGHTNESS/CONTRAST menu and function as the m/M buttons when selecting menu items. 4 (menu) button (page 9) This button displays the main menu. Installation 1-1 Do not install the monitor in the following places: • on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies, etc.) that may block the ventilation holes • near heat sources such as radiators or air ducts, or in a place subject to direct sunlight • in a place subject to severe temperature changes • in a place subject to mechanical vibration or shock • on an unstable surface • near equipment which generates magnetism, such as a transformer or high voltage power lines • near or on an electrically charged metal surface Maintenance • Clean the screen with a soft cloth. If you use a glass cleaning liquid, do not use any type of cleaner containing an anti-static solution or similar additive as this may scratch the screen’s coating. • Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver. This type of contact may result in a scratched picture tube. • Clean the cabinet, panel and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent, such as alcohol or benzene. Transportation When you transport this monitor for repair or shipment, use the original carton and packing materials. 2 GB 5 6 (contrast) </, buttons (page 9) These buttons display the BRIGHTNESS/CONTRAST menu and function as the </, buttons when making adjustments. 6 1 (power) switch and indicator (pages 6, 14, 18) This button turns the monitor on and off. The power indicator lights up in green when the monitor is turned on, and either flashes in green and orange, or lights up in orange when the monitor is in power saving mode. 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 Pin No. Signal 1 Red 2 Green (Sync on Green) 3 Blue 4 ID (Ground) 5 DDC Ground* 6 Red Ground 7 Green Ground 8 Blue Ground 9 DDC + 5V* 10 Ground 11 ID (Ground) 12 Bi-Directional Data (SDA)* 13 H. Sync 14 V. Sync 15 Data Clock (SCL)* * DDC (Display Data Channel) is a standard of VESA. 4 5 Step 2: Connect the power cord Setup This monitor works with platforms running at horizontal frequencies between 30 and 109 kHz. With the monitor and computer switched off, first connect the proper power cord for your local power supply to the monitor, then connect it to a power outlet. Step 1: Connect your monitor to your computer Selecting the on-screen menu language (LANGUAGE) Automatically sizing and centering the picture English, French, German, Spanish, Italian, Dutch, Swedish, Russian and Japanese versions of the on-screen menus are available. The default setting is English. You can easily adjust the picture to fill the screen by pressing the (auto sizing and centering) button. AC IN Press the button. The picture automatically fills the screen. 1 Press the button. See page 9 for more information on using the (HD15) 1 With the monitor and computer switched off, connect the video signal cable to the video input connector of the monitor and to the video output of the computer. MENU b to AC IN AC IN (HD15) 1 button. OK EX I T S I Z E / CENT ER GEOME TRY CONVERGENCE SCREEN COLOR L ANGUAGE OP T I ON forward side power cord to a power outlet rear side Step 3: Turn on the monitor and computer 2 Press the m/M buttons to highlight LANGUAGE and press the button again. See page 9 for more information on using the m/M buttons. L ANGUAGE b First turn on the monitor, then turn on the computer. 1-2 HD15 video output Notes • Do not touch the pins of the video signal cable connector as this might bend the pins. • When connecting the video signal cable, check the alignment of the HD15 connector. Do not force the connector in the wrong way or the pins might bend. The installation of your monitor is complete. If necessary, use the monitor’s controls to adjust the picture. If no picture appears on your screen • Check that the monitor is correctly connected to the computer. • If NO INPUT SIGNAL appears on the screen, follow the onscreen messages (page 15). • If you are replacing an old monitor with this model and OUT OF SCAN RANGE appears on the screen, reconnect the old monitor. Then adjust the computer’s graphic board so that the horizontal frequency is between 30 – 109 kHz, and the vertical frequency is between 48 – 160 Hz. For more information about the on-screen messages, see “Trouble symptoms and remedies” on page 16. Notes • This function is intended for use with a computer that provides a fullscreen picture. It may not work properly if the background color is dark or if the input picture does not fill the screen to the edges. • Pictures with an aspect ratio of 5:4 (resolution: 1280 × 1024, 1600 × 1280) are displayed at their actual resolution and do not fill the screen to the edges. • The displayed image moves for a few seconds when the button is pressed. This is not a malfunction. ENGL I SH FRANÇA I S DEUT SCH ESPAÑOL I T A L I ANO NEDER L ANDS SVENSKA GB 3 Press the m/M buttons to select a language. • • • • • • • • • ENGLISH FRANÇAIS: French DEUTSCH: German ESPAÑOL: Spanish ITALIANO: Italian NEDERLANDS: Dutch SVENSKA: Swedish : Russian : Japanese To close the menu Press the button once to return to the main MENU, and twice to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds. To reset to English Press the 0 (reset) button while the LANGUAGE menu is displayed on the screen. 6 7 Customizing Your Monitor You can make numerous adjustments to your monitor using the on-screen menu. 7 LANGUAGE (page 7) Select the LANGUAGE menu to choose the on-screen menu’s language. L ANGUAGE ENGL I SH FRANÇA I S DEUT SCH ESPAÑOL I T A L I ANO NEDER L ANDS SVENSKA x Using the , m/M, and </, buttons 1 Display the main MENU. Press the screen. button to display the main MENU on your Brightness and contrast adjustments are made using a separate BRIGHTNESS/CONTRAST menu. These settings are stored in memory for the signals from the currently selected input connector. Navigating the menu Press the button to display the main MENU on your screen. MENU OK EX I T S I Z E / CENT ER GEOME TRY CONVERGENCE SCREEN COLOR L ANGUAGE OP T I ON 8 OPTION (page 13) Select the OPTION menu to adjust the monitor’s options. The options include: • degaussing the screen • changing the on-screen menu position • locking the controls OPT I ON 1 Press either one of the DEGAUS S ON 2 Select the menu you want to adjust. Press the m/M buttons to highlight the desired menu. Press the button to select the menu item. 2 SIZE/CENTER (page 10) Select the SIZE/CENTER menu to adjust the picture’s size, centering or zoom. (brightness) m/M buttons to adjust the brightness ( ), and 6 (contrast) </, buttons to adjust the contrast (6). EX I T S I Z E / CENT ER GEOME TRY CONVERGENCE SCREEN COLOR L ANGUAGE OP T I ON S I ZE / CENTER 26 3 GEOMETRY (page 10) Select the GEOMETRY menu to adjust the picture’s rotation and shape. the horizontal and vertical frequencies of the current input signal GEOMETRY 1-3 26 4 CONVERGENCE (page 11) Select the CONVERGENCE menu to adjust the picture’s horizontal and vertical convergence. Press the m/M buttons to select the desired adjustment item. Press the </, buttons to make the adjustment. OK 6 8 . 7 kHz / 8 5Hz 1024x 768 b the resolution of the current input signal 26 2 Press the 3 Adjust the menu. MENU BR I GHTNESS / CON TRAS T 26 The horizontal and vertical frequencies of the current input signal are displayed in the main MENU. If the signal matches one of this monitor’s factory preset modes, the resolution is also displayed. 1 EXIT Select EXIT to close the menu. (brightness) m/M or 6 (contrast) </, buttons. The BRIGHTNESS/CONTRAST menu appears on the screen. b x Displaying the current input signal Use the m/M and buttons to select one of the following menus. See page 9 for more information on using the m/M and buttons. Adjusting the brightness and contrast If you are using the sRGB mode If you selected the sRGB mode in the COLOR menu, the following BRIGHTNESS/CONTRAST menu appears on the screen. 56 4 Close the menu. Press the button once to return to the main MENU, and twice to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds. GB BR I GHTNESS / CON TRAS T s RGB 76 : 56 76 For more information about using the sRGB mode, see “Adjusting the color of the picture (COLOR)” on page 12. The menu automatically disappears after about 3 seconds. CONVERGENCE TOP BOT 26 5 SCREEN (page 11) Select the SCREEN menu to adjust the picture’s quality. You can adjust the landing and moire cancellation effect. 6 COLOR (page 12) Select the COLOR menu to adjust the picture’s color temperature. You can use this to match the monitor’s colors to a printed picture’s colors. 8 x Resetting the adjustments SCREEN L AND I NG Press the 0 (reset) button. See page 14 for more information on resetting the adjustments. 26 COLOR EASY 5 0 0 0K EXPERT 6 5 0 0K COLOR RE TURN s RG B 9 3 0 0K 5 0 0 0K ON 9 Adjusting the size of the picture (SIZE/CENTER) Adjusting the shape of the picture (GEOMETRY) Adjusting the convergence (CONVERGENCE) Adjusting the quality of the picture (SCREEN) This setting is stored in memory for the current input signal. The GEOMETRY settings allow you to adjust the rotation and shape of the picture. The (rotation) setting is stored in memory for all input signals. All other settings are stored in memory for the current input signal. The CONVERGENCE settings allow you to adjust the quality of the picture by controlling the convergence. The convergence refers to the alignment of the red, green, and blue color signals. If you see red or blue shadows around letters or lines, adjust the convergence. These settings are stored in memory for all input signals. The SCREEN settings allow you to adjust the quality of the picture by controlling the moire and landing. • If the color is irregular at the corners of the screen, adjust the landing. • If elliptical or wavy patterns appear on the screen, cancel the moire. The CANCEL MOIRE and MOIRE ADJUST settings are stored in memory for the current input signal. All other settings are stored in memory for all input signals. 1 Press the button. The main MENU appears on the screen. 2 Press the m/M buttons to highlight SIZE/CENTER and press the button again. The SIZE/CENTER menu appears on the screen. 3 First press the m/M buttons to select for horizontal adjustment, or for vertical adjustment. Then press the </, buttons to adjust the size. Adjusting the centering of the picture (SIZE/CENTER) This setting is stored in memory for the current input signal. button. The main MENU appears on the screen. button. The main MENU appears on the screen. 1 Press the button. The main MENU appears on the screen. 2 Press the m/M buttons to highlight GEOMETRY and press the button again. The GEOMETRY menu appears on the screen. 2 Press the m/M buttons to highlight CONVERGENCE and press the button again. The CONVERGENCE menu appears on the screen. adjustment item. Then press the </, buttons to make the adjustment. Select 3 First press the m/M buttons to select the desired adjustment item. Then press the </, buttons to make the adjustment. 1-4 and press the button again. The SIZE/CENTER menu appears on the screen. Select 3 First press the m/M buttons to select for horizontal adjustment, or for vertical adjustment. Then press the </, buttons to adjust the centering. Enlarging or reducing the picture (ZOOM) This setting is stored in memory for the current input signal. shift the picture to the left or right at the top of the screen To horizontally shift red or blue shadows adjustment item. Then press the </, buttons to make the adjustment. Select To vertically shift red or blue shadows at the top of the screen LANDING reduce any color irregularities in the screen’s top left corner to a minimum. BOT V CONVER BOTTOM vertically shift red or blue shadows at the bottom of the screen LANDING reduce any color irregularities in the screen’s top right corner to a minimum. LANDING reduce any color irregularities in the screen’s bottom left corner to a minimum. LANDING reduce any color irregularities in the screen’s bottom right corner to a minimum. vertically shift red or blue shadows CANCEL MOIRE* 1 Press the button. The main MENU appears on the screen. 2 Press the m/M buttons to highlight SIZE/ CENTER and press the button again. The SIZE/CENTER menu appears on the screen. 3 Press the m/M buttons to select (zoom), and press the </, buttons to enlarge or reduce the picture. Note Adjustment stops when either the horizontal or vertical size reaches its maximum or minimum value. SCREEN and press the button again. The SCREEN menu appears on the screen. TOP V CONVER TOP shift the picture sides to the left or right adjust the picture width at the top of the screen button. The main MENU appears on the screen. 3 First press the m/M buttons to select the desired To expand or contract the picture sides SIZE/CENTER 1 Press the 2 Press the m/M buttons to highlight 3 First press the m/M buttons to select the desired rotate the picture 1 Press the 2 Press the m/M buttons to highlight 1 Press the MOIRE ADJUST turn the moire cancellation function ON or OFF. (MOIRE ADJUST) appears in the menu when you select ON. adjust the degree of moire cancellation until the moire is at a minimum. * Moire is a type of natural interference which produces soft, wavy lines on your screen. It may appear due to interference between the pattern of the picture on the screen and the phosphor pitch pattern of the monitor. Example of moire Note The picture may become fuzzy when CANCEL MOIRE is set to ON. 10 11 GB Adjusting the color of the picture (COLOR) The COLOR settings allow you to adjust the picture’s color temperature by changing the color level of the white color field. Colors appear reddish if the temperature is low, and bluish if the temperature is high. This adjustment is useful for matching the monitor’s color to a printed picture’s colors. 1 Press the button. The main MENU appears on the screen. 2 Press the m/M buttons to highlight COLOR and press the button again. The COLOR menu appears on the screen. EXPERT mode sRGB mode You can make additional adjustments to the color in greater detail by selecting the EXPERT mode. The sRGB color setting is an industry standard color space protocol designed to correlate the displayed and printed colors of sRGB compliant computer products. To adjust the colors to the sRGB profile, simply select the sRGB mode in the COLOR menu. However, in order to display the sRGB colors correctly (γ=2.2, 6500K), you must set your computer to the sRGB profile and adjust the brightness ( ) and contrast (6) to the numbers shown in the menu. For information on how to change the brightness ( ) and contrast (6), see page 9. COLOR EASY EXPERT 5 0 0 0K 6 5 0 0K R B I AS G B I AS B B I AS R GA I N G GA I N B GA I N s RG B 9 3 0 0K 50 50 50 50 50 50 1 Press the m/M buttons to select the color temperature row 1, then press the </, buttons to select a color temperature. Note Your computer and other connected products (such as a printer), must be sRGB compliant. COLOR EASY 3 Press the </, buttons to select the adjustment mode. There are three types of adjustment modes, EASY, EXPERT and sRGB. 4 First press the m/M buttons to select the desired adjustment item. Then press the </, buttons to make the adjustment. Adjust the selected mode according to the following instructions. COLOR EASY 5 0 0 0K EXPERT 6 5 0 0K COLOR RE TURN s RG B 9 3 0 0K 5 0 0 0K ON 1-5 1 First press the m/M buttons to select the color temperature row 1, then press the </, buttons to select a color temperature. The preset color temperatures are 5000K, 6500K, and 9300K. Since the default setting is 9300K, the whites will change from a bluish hue to a reddish hue as the temperature is lowered to 6500K and 5000K. 2 If necessary, fine tune the color temperature. First press the m/M buttons to select the color temperature adjustment row 2, then press the </ , buttons to fine tune the color temperature. If you fine tune the color temperature, the new color settings are stored in memory for each of the three color temperatures and item 1 of the on-screen menu changes as follows. • [5000K]t[ 1] • [6500K]t[ 2] • [9300K]t[ 3] 12 : 56 2, then press the </, buttons to adjust the BIAS (black level). This adjusts the dark areas of an image. s RG B : 7 6 FOR s RG B COLOR RE TURN ON 3 Press the m/M buttons to select the adjustment item 3, then press the </, buttons to adjust the GAIN (white level). This adjusts the light areas of an image. You can adjust the R (red), G (green), B (blue) component of the input signal when making changes to items 2 and 3. EASY mode EXPERT 2 Press the m/M buttons to select the adjustment item If you fine tune the color temperature, the new color settings are stored in memory for each of the three color temperatures and item 1 of the on-screen menu change as follows. • [5000K]t[ 1] • [6500K]t[ 2] • [9300K]t[ 3] Restoring the color from the EASY or sRGB menus The colors of most display monitors tend to gradually lose brilliance over several years of service. The COLOR RETURN feature found in the EASY and sRGB menus allows you to restore the color to the original factory quality levels. The explanation below explains how to restore the monitor’s color from the EASY menu. 1 Press the </, buttons to select EASY or sRGB mode. 2 First press the m/M buttons to select (COLOR RETURN), then press the , button. The picture disappears while the color is being restored (about 2 seconds). After the color is restored, the picture reappears on the screen again. Notes • Before using this feature, the monitor must be in normal operation mode (green power indicator on) for at least 30 minutes. If the monitor goes into power saving mode, you must return the monitor to normal operation mode and wait for 30 minutes for the monitor to be ready. You may need to adjust your computer’s power saving settings to keep the monitor in normal operation mode for the full 30 minutes. If the monitor is not ready, the following message will appear. COLOR EASY EXPERT 5 0 0 0K 6 5 0 0K Additional settings (OPTION) You can manually degauss (demagnetize) the monitor, change the menu position, and lock the controls. 1 Press the button. The main MENU appears on the screen. 2 Press the m/M buttons to highlight OPTION and press the button again. The OPTION menu appears on the screen. 3 Press the m/M buttons to select the desired adjustment item. Adjust the selected item according to the following instructions. Degaussing the screen The monitor is automatically demagnetized (degaussed) when the power is turned on. To manually degauss the monitor, first press the m/M buttons to select (DEGAUSS). Then press the , button. The screen is degaussed for about 2 seconds. If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. GB Changing the menu’s position Change the menu’s position if it is blocking an image on the screen. To change the menu’s on-screen position, first press the m/M buttons to select (OSD H POSITION) for horizontal adjustment, or (OSD V POSITION) for vertical adjustment. Then press the </, buttons to shift the on-screen menu. Locking the controls To protect adjustment data by locking the controls, first press the m/M buttons to select (CONTROL LOCK). Then press the , button to select ON. (CONTROL LOCK) Only the 1 (power) switch, EXIT, and of the OPTION menu will operate. If any other items are selected, the mark appears on the screen. To cancel the control lock Repeat the procedure above and set (CONTROL LOCK) to OFF. s RG B 9 3 0 0K 5 0 0 0K COLOR RE TURN AVA I L AB L E A F T ER WARM UP • The monitor may gradually lose its ability to perform this function due to the natural aging of the picture tube. 13 Resetting the adjustments This monitor has the following three reset methods. Use the 0 (reset) button to reset the adjustments. If OUT OF SCAN RANGE appears on the screen Technical Features Before contacting technical support, refer to this section. Power saving function Resetting a single adjustment item Resetting all of the adjustment data for the current input signal Press the 0 (reset) button when no menu is displayed on the screen. Note that the following items are not reset by this method: • on-screen menu language (page 7) • adjustment mode in the COLOR menu (EASY, EXPERT, sRGB) (page 12) • on-screen menu position (page 13) • control lock (page 13) 1-6 Resetting all of the adjustment data for all input signals Press and hold the 0 (reset) button for more than two seconds. Note The 0 (reset) button does not function when LOCK) is set to ON. (CONTROL I NFORMA T I ON MON I TOR I S WORK I NG I NPUT : 1 3 0 . 0 kHz / 7 5H z OUT OF SCAN RANGE CHANGE S I GNA L T I M I NG This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in three stages as shown below. Use the , m/M buttons to select the adjustment item you want to reset, and press the 0 (reset) button. Troubleshooting Power mode Power consumption 1 (power) indicator normal operation ≤ 145 W green 1 standby ≤ 100 W green and orange alternate 2 suspend (sleep)* ≤ 15 W green and orange alternate 3 active off** (deep sleep)* Approx. 1 W orange power off 0W off * “Sleep” and “deep sleep” are power saving modes defined by the Environmental Protection Agency. ** When your computer enters a power saving mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters power saving mode. If thin lines appear on your screen (damper wires) The lines you are experiencing on your screen are normal for the Trinitron monitor and are not a malfunction. These are shadows from the damper wires used to stabilize the aperture grille and are most noticeable when the screen’s background is light (usually white). The aperture grille is the essential element that makes a Trinitron picture tube unique by allowing more light to reach the screen, resulting in a brighter, more detailed picture. Damper wires On-screen messages If there is something wrong with the input signal, one of the following messages appears on the screen. WH I T E RED GREEN B L UE 1 The frequencies of the current input signal If the monitor recognizes the frequencies of the current input signal, the horizontal and vertical frequencies are also displayed. 2 The input signal condition OUT OF SCAN RANGE This indicates that the input signal is not supported by the monitor’s specifications. 3 The remedies CHANGE SIGNAL TIMING appears on the screen. If you are replacing an old monitor with this monitor, reconnect the old monitor. Then adjust the computer’s graphic board to that the horizontal frequency is between 30 – 109 kHz, and the vertical frequency is between 48 – 160 Hz. GB For more information, see “Trouble symptoms and remedies” on page 16. If NO INPUT SIGNAL appears on the screen I NFORMA T I ON MON I TOR I S WORK I NG I NPUT : NO I NPUT S I GNA L ACT I VA T E US I NG PC CHECK S I GNA L CAB L E WH I T E RED GREEN B L UE 1 The input signal condition NO INPUT SINGAL This indicates that no signal is input. 2 The remedies One or more of the following messages may appear on the screen. • If ACTIVATE USING PC appears on the screen, try pressing any key on the computer, and confirm that your computer’s graphic board is completely seated in the correct bus slot. • If CHECK SIGNAL CABLE appears on the screen, check that the monitor is correctly connected to the computer (page 6). 14 15 Trouble symptoms and remedies If the problem is caused by the connected computer or other equipment, please refer to the connected equipment’s instruction manual. Use the self-diagnosis function (page 18) if the following recommendations do not resolve the problem. Symptom If the NO INPUT SIGNAL message appears on the screen, or if the 1 (power) indicator is either orange or alternating between green and orange If the NO INPUT SIGNAL and CHECK SIGNAL CABLE message appear on the screen, or if the 1 (power) indicator is either orange or alternating between green and orange If the OUT OF SCAN RANGE message appears on the screen If no message is displayed and the 1 (power) indicator is green or flashing orange Picture flickers, bounces, oscillates, or is scrambled • Check that the power cord is properly connected. • Check that the 1 (power) switch is in the “on” position. 1-7 16 • Eliminate the use of video cable extensions and/or video switch boxes. • Check that all plugs are firmly seated in their sockets. Picture is not centered or sized properly • Press the button (page 7). • Adjust the size (page 10) or centering (page 10). Note that some video modes do not fill the screen to the edges. Edges of the image are curved • Adjust the geometry (page 10). Wavy or elliptical pattern (moire) is visible • Set CANCEL MOIRE to ON and adjust the degree of moire cancellation until the moire is at a minimum (page 11). Color is not uniform • Degauss the monitor* (page 13). If you place equipment that generates a magnetic field, such as a speaker, near the monitor, or if you change the direction the monitor faces, color may lose uniformity. • Adjust the landing (page 11). • Check that the HD15 video input connector’s pins are not bent or pushed in. xProblems caused by the connected computer or other equipment • The computer is in power saving mode. Try pressing any key on the computer keyboard. • Check that the computer’s power is “on.” • Check that the graphic board is completely seated in the proper bus slot. • Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets (page 6). • Check that the HD15 video input connector’s pins are not bent or pushed in. xProblems caused by the connected computer or other equipment • Check that the graphic board is completely seated in the proper bus slot. xProblems caused by the connected computer or other equipment • Check that the video frequency range is within that specified for the monitor. If you replaced an old monitor with this monitor, reconnect the old monitor and adjust the frequency range to the following. Horizontal: 30 – 109 kHz Vertical: 48 – 160 Hz • Use the Self-diagnosis function (page 18). • Isolate and eliminate any potential sources of electric or magnetic fields such as other monitors, laser printers, electric fans, fluorescent lighting, or televisions. • Move the monitor away from power lines or place a magnetic shield near the monitor. • Try plugging the monitor into a different AC outlet, preferably on a different circuit. • Try turning the monitor 90° to the left or right. xProblems caused by the connected computer or other equipment • Check your graphics board manual for the proper monitor setting. • Confirm that the graphics mode and the frequency of the input signal are supported by this monitor. Even if the frequency is within the proper range, some video boards may have a sync pulse that is too narrow for the monitor to sync correctly. • Adjust the computer’s refresh rate (vertical frequency) to obtain the best possible picture. Picture is fuzzy Check these items Picture is ghosting Check these items No picture If the 1 (power) indicator is not lit Symptom • Adjust the brightness and contrast (page 9). • Degauss the monitor* (page 13). • If CANCEL MOIRE is ON, the picture may become fuzzy. Decrease the moire cancellation effect or set CANCEL MOIRE to OFF (page 11). xProblems caused by the connected computer or other equipment • Change your desktop pattern. White does not look white • Adjust the color temperature (page 12). Letters and lines show red or blue shadows at the edges • Adjust the convergence (page 11). Monitor buttons do not operate ( appears on the screen) • If the control lock is set to ON, set it to OFF (page 13). COLOR RETURN function does not operate • Before using this function, the monitor must be in normal operation mode (green power indicator on) for at least 30 minutes. For more information on using the COLOR RETURN function, see page 13. • Adjust the computer’s power saving settings to keep the monitor in normal operation mode for more than 30 minutes. • The monitor may gradually lose its ability to perform this function due to the natural aging of the picture tube. COLOR EASY EXPERT 5 0 0 0K 6 5 0 0K s RG B 9 3 0 0K 5 0 0 0K COLOR RE TURN AVA I L AB L E A F T ER WARM UP A hum is heard right after the power is turned on • This is the sound of the auto-degauss cycle. When the power is turned on, the monitor is automatically degaussed for two seconds. * If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. A humming noise may be heard, but this is not a malfunction. Displaying this monitor’s name, serial number, and date of manufacture. While the monitor is receiving a video signal, press and hold the button for more than five seconds to display this monitor’s information box. If the problem persists, call your service representative and give the following information. • Model name: GDM-5403 • Serial number • Name and specifications of your computer and graphics board. Example INFORMATION b MODEL : GDM 5403 SER NO : 1234567 MANUFACTURED : 1999-52 17 GB Self-diagnosis function This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer(s), the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard. Specifications CRT Viewable image size Maximum resolution 1 2 Standard image area 1 (power) indicator If the 1 (power) indicator is green Deflection frequency* 1 Disconnect the video input cable or turn off the AC input voltage/current Power consumption Dimensions connected computer. 2 Press the 1 (power) button twice to turn the monitor off and then on. Mass Plug and Play 0.24 mm aperture grille pitch 21 inches measured diagonally 90-degree deflection FD Trinitron Approx. 403.8 × 302.2 mm (w/h) (16 × 12 inches) 19.8" viewing image Horizontal: 1600 dots Vertical: 1200 lines Approx. 388 × 291 mm (w/h) (15 3/8 × 11 1/2 inches) or Approx. 364 × 291 mm (w/h) (14 3/8 × 11 1/2 inches) Horizontal: 30 to 109 kHz Vertical: 48 to 160 Hz 100 to 240 V, 50 – 60 Hz, 2.0 – 1.0 A Approx. 145 W Approx. 498 × 491 × 478 mm (w/h/d) (19 5/8 × 19 3/8 × 18 7/8 inches) Approx. 32 kg (70 lb 9 oz) DDC1/2B/2Bi, GTF** 3 Press the , button for 2 seconds before the monitor enters power saving mode. 1-8 If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cables and check the condition of your computer(s). If the color bars do not appear, there is a potential monitor failure. Inform your service representative of the monitor’s condition. If the 1 (power) indicator is flashing orange Press the 1 (power) button twice to turn the monitor off and then on. If the 1 (power) indicator lights up green, the monitor is working properly. If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your service representative of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and video board. 18 * Recommended horizontal and vertical timing condition • Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. • Horizontal blanking width should be more than 2.3 µsec. • Vertical blanking width should be more than 450 µsec. ** If the input signal is Generalized Timing Formula (GTF) compliant, the GTF feature of the monitor will automatically provide an optimal image for the screen. Design and specifications are subject to change without notice. GDM-5403 SECTION 2 DISASSEMBLY 2-1. CABINET REMOVAL Push in the tip of a screwdriver about 5mm to unlock the claw. Cabinet Cabinet 4 5 Four screws (+ BVTT 4 x 8) Bezel assembly Bezel assembly 3 Top cover Two screws (+ BVTP 4 x 16) Two claws 2 7 Two claws Cabinet 1 6 2 Four screws (+ BVTT 4 x 8) Video shield 2-2. D BOARD REMOVAL 3 5 Screw (+ P 3.5 x 20) 4 Two screws (+ BVTP 3 x 12) D board 1 Three screws (+ BVTT 4 x 8) B GND CN504 CN505 Two hooks 2 2-1 A Open the D block in the direction of the arrow A . and remove of the arrow B . GDM-5403 2-3. G BOARD REMOVAL 3 Four screws (+BVTP 3 x 8) G shield 4 Three screws (+ BVTT 4 x 8) 1 CN602 6 CN654 B CN653 CN652 G board CN650 7 GND Two screws (+ BVTP 3 x 8) GND 8 AC inlet (3P) A Two hooks 2 Open the G block in the direction of the arrow A . and remove of the arrow B . 5 Two printed circuit board holders 2-4. A BOARD, TERMINAL BOARD BRACKET REMOVAL 4 A board (2/2) 3 A board (1/2) 2 When installing Terminal board bracket, be sure to apply screw lock on 2 spots after screws (HD15) are fixed. Three screws (+BVTT 4 x 8) A board (1/2) 1 screw (M4) (EXT tooth washer) A board (1/2) Screw lock 6 5 Terminal board bracket Two screws (HD15) 2-2 GDM-5403 2-5. N BOARD REMOVAL CN5003 CN5002 CN001 CN5001 CN002 CN010 CN011 CN007 2 N board 1 Printed circuit board holder 2-6. SERVICE POSITION CAUTION : SHORT D,G boards Rear shield If the claw is hooked, opening and closing the board is impossible. Do not try to do it by force. D board (Refer to 2-2.) If the claw is hooked, opening and closing the board is impossible. Do not try to do it by force. CN602 AC inlet (3P) G board (Refer to 2-3.) 2-3 GDM-5403 2-7. BEZEL ASSEMBLY, H BOARD REMOVAL 1 Before removing the bezel assembly, secure the picture tube by attaching two screws to the picture tube shield at the positions shown with an arrow (diagonal two places) to prevent the picture tube from falling. (Use the screws +BVTT 4 x 8 that fix top cover.) 2 Four screws (Tapping screw 5) Picture tube shield 5 H board CN801 4 3 Two screws (+ BVWHTP 3 x 12) Bezel assembly 2-8. J BOARD REMOVAL Three degaussing coil holders 1 Degaussing coil CN891 2 3 4 Degaussing coil holder Claw J board When installing J board, put the behind of the board in two hooks. J board Two hooks Claw 2-4 GDM-5403 2-9. PICTURE TUBE REMOVAL Remove the bezel assembly. (Refer to 2-7) 1 Open the D block (Refer to 2-2.) 3 8 5 A board Deflection yoke Anode cap Open the G block (Refer to 2-3.) 7 Neck assembly Three connectors CN4 CN5 GND 4 6 2 Picture tube • REMOVAL OF ANODE-CAP NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after removing the anode. • REMOVING PROCEDURES c b a Anode Button 1 Turn up one side of the rubber cap in the direction indicated by the arrow A. 2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow B. • HOW TO HANDLE AN ANODE-CAP 1 Don’t scratch the surface of anode-caps with sharp shaped material! 2 Don’t press the rubber hardly not to damage inside of anodecaps! A material fitting called as shatter-hook terminal is built in the rubber. 3 Don’t turn the foot of rubber over hardly! The shatter-hook terminal will stick out or damage the rubber. 2-5 3 When one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling up it in the direction of the arrow C. GDM-5403 2-10. HARNESS LOCATION J board H board Picture tube CN891 CN801 CN5 4pin 4pin CN4 CN653 CN5001 CN5003 CN509 CN502 CN5002 CN602 CN654 CN508 CN505 CN001 FBT CN504 CN603 CN652 CN011 CN601 CN010 CN650 CN007 CN651 CN506 CN501 AC inlet D board N board Rear shield Terminal board bracket CN401 CN403 CN405 CN407 CN408 A board 2-6 CN406 G board GDM-5403 SECTION 3 SAFETY RELATED ADJUSTMENT When replacing or repairing the shown below table, the following operational checks must be performed as a safety precaution against X-rays emissions from the unit. c) Beam Current Protector Circuit Check (1st Protector): D Board 1) Apply 4.5 V DC to CN504 0 pin on the D board, and check high voltage value. 2) Connect constant current source to a section between T902 (FBT) qa pin and qs pin (GND) on the D board, and check that high voltage checked in 1) lowers by 1.50 kV or more when the specified current flows to the qa pin. [Specification]: 2.00 + 0.00/– 0.01 mA Part Replaced ([) HV ADJ RV901 Part Replaced (]) HV Regulator Circuit Check D Board C920, IC901, R923 R924, R929, R945, RV901, T902 (FBT) • Mounted D Board HV Protector Circuit Check D Board C922, C925, C926, D912, D914, D915, D921, Q907, Q908, R921, R922, R932, R937, R939, T902 (FBT) • Mounted D Board Beam Current Protector Circuit Check d) Beam Current Protector Circuit Check (2nd Protector): D Board 1) Connect constant current source to a section between T902 (FBT) qa pin and qs pin (GND) on the D board, and check that the voltage of CN504 0 pin becomes 0 V or less when the specified current flows to the qa pin. [Specification]: 1.70 + 0.00/– 0.01 mA D Board C910, C921, C933, D901, D902, D913, IC503, IC901, R901, R920, R928, R930, R931, R940, R941, T902 (FBT) • Mounted D Board G Board IC652 • Mounted G Board N Board IC001, R031, R032 • Mounted N Board e) Beam Current Protector Circuit Check : G Board 1) Apply 264 V AC. 2) Enter about 5 V to CN650 4 pin on the G board, and check that the output voltage of CN653 2 pin is about 15 V. 3) Enter about 0 ± 0.2 V to CN654 4 pin, and check that the output voltage of CN653 2 pin becomes 1.0 V or less. * Confirm one minute after turning on the power. a) HV Regulator Circuit Check 1) Enter black crosshatch signal (black on white background), and check that high voltage is in the specified range. [Specification]: 27.00 ± 0.10 kV 2) Check that the voltage of D912 cathode on the D board is 27.0 V or more. f) Beam Current Protector Circuit Check : N Board 1) Check that the protector operates, when the voltage of CN010 qh pin on the N board is lowered to 0 V or less (for more than 2 seconds). b) HV Protector Circuit Check 1) Enter black crosshatch signal (black on white background). 2) Apply the specified voltage to the D912 cathode on the D board, and check that high voltage is 0.1 kV or less. [Specification]: 31.90 + 0.00/– 0.05 V 3-1 GDM-5403 SECTION 4 ADJUSTMENTS Note: Hand degauss must be used on stand-by or power-off condition. This model has an automatic earth magnetism correction function by using an earth magnetism sensor and a LCC coil. When using a hand degauss while monitor (LCC coil) is being operated, it sometimes gets magnetized, and the system may not work properly as a result. • Landing Rough Adjustment 1. Enter the full white signal. (or the full black dots signal). 2. Adjust the contrast to the maximum. 3. Make the screen monogreen. Note: Off the outputs from R ch and B ch of SG. 4. Reverse the DY, and adjust coarsely the purity magnet so that a green raster positions in the center of screen. 5. Adjust the tilt of DY, and fix lightly with a clamp. Note: “TILT” = “128”. • Write terrestrial magnetism sensor reading VX and VY to “LCC VX” and LCC VY” respectively. Adjust the landing by moving “LCC NS”, “LCC LT”, “LCC LB”, “LCC RT” and “LCC RB”. However, the register adjustment must be limited within the following range. “LCC NS” 128 ± 15 “LCC LT”, “LCC LB”, “LCC RT”, “LCC RB” 128 ± 40 Save the service data. • Landing Fine Adjustment 1. Put the set inside the Helmholtz coil. (“LCC SW” = “12”) 2. Input the single green signal and set the “CONTRAST” = “255”. Note: After the W/B adjustment with 9300 K, measure an average of ΣIk when a full white signal is entered in the CONT MAX/BRT CENT status. Then make adjustment so that the specified screen can be attained after aging for 2 hours with Ik equivalent to 30% of the average value. 3. Demagnetize the metal part of the chassis with the hand degausser and coil degausser, and the CRT surface with the hand degausser. Input AC 230V to AC IN, turn on and off the power to perform auto degaussing. (Perform auto degaussing by setting “FUNCTION SW” = 1. Return to the original value after use.) Demagnetize the CRT surface with the hand degausser again. Note: (1) Hand degauss must be used on stand-by or power-off condition. This model has an automatic earth magnetism correction function by using an earth magnetism sensor and a LCC coil. When using a hand degauss while monitor (LCC coil) is being operated, it sometimes gets magnetized, and the system may not work properly as a result. (2) Adjust in a non-magnetic field. (3) If adjusting in a magnetic fields, add the shift from the nonmagnetic field in your estimation. 4. Attach the wobbling coil to the designated part of the CRT neck. 5. Attach the sensor of the landing adjustment unit on the CRT surface. 6. Adjust the DY position and purity, and the DY tilt, and landing of the center and 4 corners with the landing checker. After adjustment, set “LCC SW” to “13”. <Specifications> Adjust so that the green is within the specification given right. 4 corner adjust target : within ± 1 The red and blue must be within the specification given right with respect to the green. A difference between red and blue must be within the specification given right. (µm) 0 ± 3 0 ± 7.5 0 ± 3 0 ± 3 0 ± 7.5 0 ± 3 0 ± 3 0 ± 7.5 0 ± 3 ±6 ±6 (µm) ±6 ±6 ±6 ±6 ±6 ±6 ±6 10 10 (µm) 10 10 7 10 10 10 10 * Adjustment and measurement should be made at the points one inch inside the fluorescent screen. 7. Tighten DY screw. Note: Torque 22 ± 2 kg•cm (2.2 ± 0.2 Nm) auto degauss it. 8. For the up/down swing, swing the DY and insert a wedge so that the up and down pins are equal at the top and bottom. Adjust the H.TRP VR of DY so that the horizontal trapezoid is equal at the left and right. Insert the wedge firmly so that the DY does not shake. 9. Check the landing of each corner, and if it does not satisfy the specification, adjust the landing of four corners using “LCC LT“, “LCC LB”, “LCC RT” and “LCC RB”. However, the register adjustment must be limited within the following range. “LCC NS” 128 ± 15 “LCC LT”, “LCC LB”, “LCC RT”, “LCC RB” 128 ± 40 After adjustment, save the service data. 10. Remove the sensor and wobbling coil. 11. Switch the signal to R.G.B., and check that each color is pure. 12. Check that the DY is not tilting, and fix the purity Mg with a white pen. Fix wedges with RTV. 4-1 GDM-5403 Connect the communication cable of the computer to the connector located on the D board. Run the service software and then follow the instruction. 1 1-690-391-21 2 A-1500-819-A Interface Unit 3 3-702-691-01 Connector Attachment IBM AT Computer as a Jig To BUS CONNECTOR D-sub (9 Pin [female]) mini Din (8Pin) *The parts above ( 1 4 Pin 4 Pin 3 ) are necessary for DAS adjustment. • Convergence Rough Adjustment (1) Receive an image of the white crosshatch signals (white lines on black). (2) Place the protrusions of the 6-fold poles magnet attached to the CRT neck upon each other. (3) Make rough adjustment of the H and V direction convergence by using 4-fold poles magnet. • White Balance Adjustment Specification 1. 9300 K x = 0.283 ± 0.005 y = 0.298 ± 0.005 (All White) 2. 6500 K x = 0.313 ± 0.005 y = 0.329 ± 0.005 (All White) 3. 5000 K x = 0.346 ± 0.005 y = 0.359 ± 0.005 (All White) Purity 4-pole magnet 6-pole magnet YCH H-TRP YBH 4 Pin 2-pole magnet TLH • Vertical and Horizontal Position and Size Specification A b APH XBV b XCV B a * Set so that the protruding parts of the 2 magnet rings agree with each other. XCV a b B 4:3 5:4 A 388 364 B 291 291 2.0 mm 2.0 mm • Focus adjustment Adjust the focus volume 1 and 2 for the optimum focus. TLH XBV R B R TLV a MODE B B R YCH R YBH R B B R R B R B Focus 1 • Convergence Specification Focus 2 B V A fH 60kHz 60kHz> A 0.20 mm 0.24 mm B 0.24 mm 0.28 mm FBT 4-2 SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAMS 5 14 9 4 13 8 3 11 2 9 1 7 GOUT 12 7 11 6 BOUT BIN1 GIN1 TXD 20 4 TXD +15V 24 +15V 25 2 +15V –15V 22 4 –15V –15V 23 1 +12V HDF 14 2 C. BLK 4 SCL 13 SDA 14 6 +80V VDF 12 ABL 10 HV DET 8 S0 7 H CENT 6 S6 5 HSPBAL 4 HLINBAL 3 H SIZE 2 H SHAPE 1 8 9 10 TO G BOARD CN653 F TO G BOARD CN654 S0 5 V. SYNC 6 HFBP 7 4 9 13 1 18 19 20 21 SCL 28 13 8 15 16 Hfly XT1 XT0 1 8 4 5 H OUT, BUFF Q515, 520 CN508 +220V 5 +220V 4 H CENT L 3 H CENT N 2 H CENT H 1 IC502 H CENT OUT H CENT H 5 HSP HDIN ECO SW 16 3 ECO SW PWR SW 14 4 PWR SW DGUS SW 12 5 DGUS SW HTR SW 10 6 HTR SW TH DET 25 +VIN OUT 4 2 8 HD 6 V RET 3 VSHAPE 1 +12V 4 HEATER 1 STBY+5V 2 1W+5V +80V 4 +80V +220V 6 +220V +12V 8 +12V 1 G2 1 G2 5V 17 DRIFT CORRECT Q401 H ERRIN 3 – + 7 G2 CONT Q406, 407, 410 CN506 HV REG SW Q905 HDIN 2 T901 HRC 3 5 12 ERROUT – + HVD 11 T902 FBT 5 HV DRV Q903, 904 HV OUT Q906 17 RV901 HV DET H DRV Q701-705 2 11 2 PIN OUT Q508 +220V 5 14 14 5 15 7 IC701 V DY OUT V RET 3 V SHAPE 5 OUT VCC – +12V + OUT 4 11 2 V+ T503 HST PIN AMP Q524 HFBP HD +12V 7 8 O2 V– CN509 2 1 V– 3 5 V+ O4 O3 9 3 VSHAPE Q523 –4 HL OUT Q516, 518 14 13 HLIN 3 2 4 1 V RET FV FV 6 HV DET Q907, 908 +80V +15V FC 16 S5 –15V HV ADJ FC T701 DFT L505 HOC GAIN SW Q526 S1 HV HV 1 2 15 V DRV Q706, 707 PIN DRV Q504, 505 6 TO G BOARD CN650 S3 S5-1 E TO G BOARD CN652 IC405 (1/2) +220V 5 PWMOUT S4 S2 PS401 1A 6 PWMOUT HDF O1 HFBP 9 5V-2 IC901 HV CONTROL 10 14 +1 19 7 X401 8MHz 12 VDF ABL DET S1 1 HEATER+ 11 5 ABL 21 KB HEATER+ 7 11 –3 22 KB 7 10 5 T502 HCT H SIZE 23 S5 24 TH DET TH DET Q521, 522 HSP S3 1 V901 PICTURE TUBE –VIN S5-1 24 TH DET 11 14 HD IC501 PIN CONTROL H SIZE 1W+5V 3 5 GND BUFFER Q101, Q201, Q301 14 H DRV Q502, 503 +12V VEE H CENT Q514 2 BOUT VCC H CENT L 3 HLIN 18 KG +220V HSPBAL 1W+5V GOUT BIN HFBP CN502 S4 25 GCI PWM1 IC404 OSD H OUT Q509 H CENT H 2 STBY+5V KG CN406 26 RCI BCI VS T501 HDT S6 1 5 3 17 VDD (DEFLECTION) H CENT N 1 20 KR CN405 GIN 12 SDA VCC KICK Q402 H CENT STBY+5V S2 D G HV DET KR (VIDEO AMP, RGB OUT) S5 TO N BOARD CN011 SDA SDA 3 ECS ABL DET CN408 5 3 ROUT ABL VDF CN505 D SCL SCL 4 H. SYNC D/A2 RIN CN501 HDF 4 BIK 6 CLP HSPBAL TO N BOARD CN010 RXD 6 GIK 7 SYNC ON G D/A3 BLK 14 RIK G. SYNC DET CLP 15 PWM4 20 H CENT C 3 BOUT 27 PWM3 DDC SDA 1 SCL 22 SDA 23 CN503 18 BIN 26 PWM2 16 IC407 A RXD 2 GOUT OSD BLK 17 HS/VS1 30 D/A4 AV VS1 C. BLK D/A5 OSD B 18 SYNC SEP OUT 21 FBLK DDC +5V 1 25 CLP OSD G 17 5V STBY+5V 33 GIN 14 IC406 CUTOFF AMP BOUT 19 HFBP 2 8 CN407 ROUT G2 OSD R 21 DDC SCL 1 V. SYNC 16 BOUT ROUT HOST GND 1 H. SYNC CN504 BIN 38 RIN 19 V-DET 25 STBY+5V 11 GOUT 12 G. DET CN403 TO N BOARD CN001 29 GIN 41 21 G DET IN B DET IN B 6 ROUT 23 R DET IN RIN1 32 RIN HV 15 10 2 GOUT INPUT 35 ROUT FC CN401 HD15 IC403 RGB AMP IC402 RGB DRIVE FV IC401 RGB DRIVE IC503 AMP S0-4, S6 S CAP CHANGE Q501, 506, 507, 510-513, 517, 525 2 V. DY C 3 V. DY H 9 H. DY H 10 H. DY H 5 H. DY C 6 H. DY C 1 T505 HLC S5 RY501 S5 RELAY DRV Q519 B-SS9272<AEP>-BD1-EPS05 5-1 5-2 V. DY H. DY µ-COM, V.CONV, H. CONV, LCC, GEO MAGNETIC SENSOR N IC5301 (2/2) SCL1 SDA1 6 5 6 + – 7 CN5002 8 IC5301 (1/2) SDA VCC IC001 CPU/DSP 7 VCLK 8 SCL STBY+5V VS1 DET1 4 + – 3 IC011 ROM 2 HS/CS 1 6 VS 1 5 HOST GND 1 1 CLP 20 C. BLK 18 SYNC ON G 16 G. SYNC DET 15 SCL 9 SDA 8 H. SYNC 14 V. SYNC 13 HFBP 12 DET1 SCL1 47 HS1 104 VC1 103 29 53 51 108 UPWM22 UBI2 UPWM20 UIN2 UPWM18 UIN1 P52/INT2 UPWM13 UOUT3 UPWM17 UOUT1 UPWM9 152 D SCL 41 D SDA 42 HSOUT 98 4 149 6 131 6 + – 7 4 SCL1 P82 6 39 5 38 6 VDF 14 HV DET 18 H CENT 20 HSPBAL 22 HLINBAL 23 HSIZE 24 HSHAPE 25 TXD 6 RXD 8 +15V 1 +15V 2 +15V –15V 3 -15V –15V 4 STBY+5V 10 S0 19 S6 21 Q010 71 128 86 138 126 144 136 133 45 44 AIN12 P90 DAC0 RESET 61 UPWM12 40 7 4 SCL S4 D TO D BOARD CN505 Q012 2 S3 3 S5 4 S2 5 S1 7 TH DET 1 PWR SW 12 DGUS SW 14 HTR SW 16 VRET 23 ECO SW 10 58 60 56 55 88 15, 94 95 93 92 UPWM7 UPWM15 P10/A0 UPWM11 P11/A1 UPWM10 AIN1 TXD AIN2 HFBP 18 HD 20 VSHAPE 25 +12V 22 +12V STBY+5V 6 STBY+5V 1W+5V 8 1W+5V HD VSP X001 24.756MHz 64 8 2 LCC-NS (–) 5 ROTATION (+) PA0 PA6 PA4 P12/A2 UOUT8 PA3 UPWM4 PA5 UPWM3 PA2 UPWM5 PA1 AIN11 P42/D2, P93 UPWM2 UPWM1 AIN13 P94 P95 P92 UOUT5 INT1 6 ROTATION (–) 3 H CONV (+) 4 H CONV (–) 1 V CONV (+) 2 V CONV (–) 6 1W+5V 7 STBY+5V 1 LED0 2 LED1 3 KEY DET 8 ENV DRI ROTATION H. CONV V. CONV 2 RESET SW Q008 1W+5V +15V STBY+5V 3 LED0 LED0 4 LED1 LED1 76 KEYDET KEY DET 77 ENV ENV 19 ACTIVE OFF DET Q004-006 8 UIN6 5 18 IC010 H. V. OSC, AFC, H. DRV, V. SHAPE 124 99 13 HD SW Q011 HC1 25 120 35 117 34 122 33 114 29 111 27 90 13 96 9 67 5 109 8 66 4 AFC FIL IC004 ECO DET 1 HD DUTY 3 VC1 11 14 1CLR 1Q 5 2CLR 1CK 2CK 2Q 9 BSHPLVL DVSHAPE VDC REG9V 21 CURRENT MILLER Q001-003 +12V IC005 ECO DET HPHASE HFREQ 1 HPLL 13 AFC SW VSH HS FBP HD VSAWRST VSHAPE 1CLR 1Q 5 2CLR 30 15 HC2 6 VC2 11 3 1CK 2CK 2Q 9 XTB XTD B-SS9272<AEP>-BD2-EPS05 5-3 LCC-NS CK ECO SW Q007 UOUT4 63 LCC-NS (+) RXD ECO SW HFBP 3 34 14 UPWM6 59 8 + – 3 IC002 WDT WC 33 P41/D1 P45/D5 CN011 1 LCC-RT CN007 AIN10 P15/A5 54 LCC-RT (–) UPWM8 P46/D6 STBY+5V 6 LCC-RB IC5401 (1/2) SDA HFBP TO D BOARD CN504 12 + – 7 VSOSD C 89 16 LCC-RT (+) CN5001 2 IC5401 (2/2) 84 CN010 HDF LCC-RB (–) 5 LCC-LT CN5003 8 + – 3 IC003 EEP ROM SDA1 8 IC5201 (1/2) 83 75 AIN0 LCC-RB (+) 2 + – 7 IC006 5 LCC-LT (–) 7 IC5201 (2/2) 148 GS5001 GEOSENSOR AIN8 2 LCC-LB 140 SDA2 AIN7 ABL + – 3 SCL2 HFBP LCC-LT (+) IC5101 (1/2) 153 UOUT7 VS OSD LCC-LB (–) 1 157 UIN5 SOG DET 4 SOG DET 2 UBI1 LCC-LB (+) 8 ECO SW DDC SDA 1 UPWM19 46 + – 7 HSOUT 3 6 156 HD 4 DDC SCL 1 UPWM21 VSP B TO A BOARD CN403 DDC+5V 1 SDA1 VS1 IC5101 (2/2) CN001 3 5-4 I TO H BOARD CN801 G (POWER SUPPLY) CN654 4 IC650 +220V SHUNT REG S891 POWER J T620 PIT TH601 CN891 CN603 1 AC L OUT AC L OUT 1 3 AC L IN AC L IN 3 5 D650 D610 RECT (POWER SW) 1 3 3 3 T601 9 1 VCC CATHODE 3 4 DGC RY603 DGC 1 DGC 4 H CENT L 4 +220V 5 +220V 6 +80V 4 –15V 1 +12V 2 +15V 1 2 D652 2 11 1 12 4 +80V 6 +220V 8 +12V 9 HEATER 1 SYBY+5V 2 1W+5V 1 STBY+5V 2 1W+5V 3 ECO SW 6 HTR SW 4 PWR SW 5 DGUS SW PS650 2.0A L410 AFC CN652 T621 PRT 1 VCC SW Q631-633 RELAY DRV Q691 F TO D BOARD CN501 6 5 3 G TO D BOARD CN508 GND 5 1 CN601 9 10 7 L SEN AC N 2 H CENT N 3 CN653 10 DRAIN 1 4 AC SEN F601 6.3A CN602 2 7 8 AC L H CENT H 6 RY602 AC INLET 1 Q603 REG OUT START UP IC654 +12V REG 1 6 2 7 3 IN OUT 3 PROTECTOR POWER SW Q650-654, 667 E TO A BOARD CN405 CN650 CN801 I TO N BOARD CN007 4 REG SW Q621 1W+5V 6 1W+5V STBY+5V 7 STBY+5V LED0 1 LED1 2 KEY DET 3 ENV DRI 8 5 LED DRV Q801, 802 PH620 STBY+5V LED DRV Q803, 804 IC630 REG 8 R G 7 D801 VCC SW Q610 6 2 POWER RESET STBY+5V TH801 ASC IN MENU OUT B-SS9272<AEP>-BD3-EPS05 2 2 4 4 VCC OUT CTL S804, S805, S806 V+ 2 IC652 STBY+5V REG 2 V– 4 PROTECT Q670 8 1 REG SW Q630 S801, S802, S803 1 IC653 1W+5V REG 1 T630 SRT 3 3 1 H– 3 S807 IC651 HEATER REG 5 H+ 2 FUNCTION KEY OUT CTL PH630 H (USER CONTROL) VCC 3 1 4 2 VADJ IC680 4 1 5 HEATER SW Q671 3 1 5-5 5-6 H TO D BOARD CN502 5-2. FRAME SCHEMATIC DIAGRAM 10 15 5 9 14 4 8 13 3 INPUT1 CN401 HD15D-SUB 7 A 12 2 6 11 1 VIDEO AMP, RGB OUT CN407 8P CN402 6P WHT :S-MICRO CN408 8P 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 KB GND KG GND KR GND HEATER+ GND RCV PICTURE TUBE H G2 G2 N.C CN406 2P WHT :VH C BLOCK G2 GND KB KR G2 G4 KG G1 GM HV (CRT SOCKET)FV GND FC 1 2 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 CN403 21P L-FPC ABL(NC) CLP GND C.BLK GND SYNC_ON_G G.SYNC_DET H.SYNC V.SYNC HFBP GND INPUT_SEL SCL SDA GND HS/CS 1 VS 1 DDC+5V 1 DDCSCL 1 DDCSDA 1 HOSTGND 1 STBY+5V 1W+5V GND +80V N.C +220V N.C +12V HEATER NC NC NC NC NC NC CN405 9P WHT-L :S-MICRO 1 2 3 4 5 6 KB GND KG GND KR GND HEATER+ GND HV N.C G2 2 1 CHASSIS GND (DEFLECTION) 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TH DET S4 S3 S5 S2 STBY+5V S1 1W+5V GND ECO_SW GND PWR SW GND DGUS SW GND HTR SW GND HFBP GND HD GND +12V VRET GND VSHAPE CN509 10P :VH GND 1 V.DY C 2 V.DY H 3 NC 4 H.DY C 5 H.DY C 6 NC 7 NC 8 H.DY H 9 H.DY H 10 H.DY FASTEN V.DY CN503 4P WHT GND STBY+5V RXD TXD 1 2 3 4 5 6 7 8 CRT SHIELD CN801 11P WHT-L :S-MICRO H(USER CONTROL) 5-7 1 5-8 1 2 3 4 ECS STBY+5V 1W+5V ECO SW PWR SW DGUS SW HTR SW GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 CN508 8P WHT :S-MICRO LED0 LED1 KEY_DET NC GND 1W+5V STBY+5V ENV_DRI GND LED0 1 LED1 2 KEY_DET 3 NC 4 GND 5 1W+5V 6 STBY+5V 7 ENV_DRI 8 GND 9 GND 10 GND 11 1 2 3 4 5 6 7 8 9 CN007 9P WHT :S-MICRO CN5003 2P WHT :S-MICRO LCC-NS(+) LCC-NS(-) LCC-NS LCC-RB LCC-RT LCC-LB 1 2 LCC-RT(+) LCC-RT(-) LCC-RB(+) LCC-RB(-) LCC-LT(+) LCC-LT(-) LCC-LB(+) LCC-LB(-) 1 2 3 4 5 6 7 8 LCC-LT ROTATION CN5002 8P YEL :S-MICRO V CONV(+) V CONV(-) H CONV(+) H CONV(-) ROTATION(+) ROTATION(-) AC L N.C AC N 1 2 3 4 5 6 1 2 3 1 2 3 4 5 6 7 H.CONV J(POWER SW) STBY+5V 1W+5V ECO SW PWR SW DGUS SW HTR SW GND V.CONV CN602 3P WHT :VH CN650 7P WHT :S-MICRO CN506 2P WHT :VH 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 ABL(NC) CLP GND C.BLK GND SYNC_ON_G G.SYNC_DET H.SYNC V.SYNC HFBP GND INPUT_SEL SCL SDA GND HS/CS 1 VS 1 DDC+5V 1 DDCSCL 1 DDCSDA 1 HOSTGND 1 CN001 21P :FFC 8 7 6 5 4 3 2 1 NC NC NC NC NC NC NC NC CN603 3P 1 2 3 GND D 1 2 3 4 5 6 7 AC L OUT N.C AC L IN 1 2 3 4 5 6 FC CN507 1P CN502 7P WHT :S-MICRO 1 2 3 CN891 3P WHT :VH AC L OUT N.C AC L IN +12V +15V GND -15V GND +80V CN5001 6P WHT :S-MICRO POWER GND TH DET S4 S3 S5 S2 STBY+5V S1 1W+5V GND ECO_SW GND PWR SW GND DGUS SW GND HTR SW GND HFBP GND HD GND +12V VRET GND VSHAPE FV CN505 25P :FFC CN011 25P FFC CN653 6P WHT :S-MICRO FBT +15V +15V -15V -15V GND TXD GND RXD GND STBY+5V GND HDF GND VDF GND ABL GND HV DET S0 HCENT S6 HSPBAL HLINBAL HSIZE HSHAPE +12V +15V GND -15V GND +80V CN604 1P 1 G POWER SUPPLY 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 DGC N.C N.C DGC µ-COM, V.CONV,H.CONV,LCC, GEO MAGNETIC SENSOR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 CN501 6P WHT :S-MICRO 1 2 3 4 N 1 2 3 4 5 6 7 8 CN504 25P :FFC H CENT H H CENT N H CENT L +220V +220V N.C GND GND CN652 9P WHT :S-MICRO STBY+5V 1W+5V GND +80V N.C +220V N.C +12V HEATER H CENT H H CENT N H CENT L +220V +220V N.C GND GND CN601 4P WHT :VH DGC CN654 8P WHT :S-MICRO CN010 25P FFC +15V +15V -15V -15V GND TXD GND RXD GND STBY+5V GND HDF GND VDF GND ABL GND HV DET S0 HCENT S6 HSPBAL HLINBAL HSIZE HSHAPE 1 2 3 4 5 6 7 8 9 CN002 8P WHT :S-MICRO CONNECTOR PANEL GND B-SS9272<AEP>-KESSENZU-EPS05 5-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS 5-3. CIRCUIT BOARDS LOCATION Note: D • All capacitors are in µF unless otherwise noted. (pF: µµF) Capacitors without voltage indication are all 50 V. • Indication of resistance, which does not have one for rating electrical power, is as follows. A Pitch: 5 mm Rating electrical power 1/4 W (CHIP : 1/10 W) • All resistors are in ohms. • f : nonflammable resistor. • Ï : fusible resistor. • f : internal component. • p : panel designation, and adjustment for repair. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. e : earth-ground. • • E : earth-chassis. • The components identified by [ in this basic schematic diagram have been carefully factory-selected for each set in order to satisfy regulations regarding X-ray radiation. Should replacement be required, replace only with the value originally used. • When replacing components identified by ] , make the necessary adjustments indicated. (See page 3-1) • When replacing the part in below table, be sure to perform the related adjustment. N G H J Note: The components identified by shading and mark ¡ are critical for safety. Replace only with part number specified. • • • • • • • • Terminal name of semiconductors in silk screen printed circuit ( ) Part Replaced ([) HV ADJ RV901 Device 1 HV Regulator Circuit Check Base HV Protector Circuit Check Beam Current Protector Circuit Check D Board C920, IC901, R923 R924, R929, R945, RV901, T902 (FBT) • Mounted D Board Circuit Terminal name Collector Transistor Part Replaced (]) 2 Transistor 3 Diode Emitter Collector Base Emitter Cathode Anode Cathode 4 D Board C922, C925, C926, D912, D914, D915, D921, Q907, Q908, R921, R922, R932, R937, R939, T902 (FBT) • Mounted D Board Diode Anode (NC) Cathode 5 Diode Anode (NC) Common 6 7 Diode Anode Diode Cathode Common Anode Cathode Common D Board C910, C921, C933, D901, D902, D913, IC503, IC901, R901, R920, R928, R930, R931, R940, R941, T902 (FBT) • Mounted D Board G Board IC652 • Mounted G Board N Board IC001, R031, R032 • Mounted N Board 8 Diode Anode Anode Common 9 Diode Anode Anode Common 0 Diode Cathode Cathode Common qa Diode qs Diode qd Transistor (FET) Cathode Anode Anode Cathode Drain Cathode Cathode Anode Anode Source Gate D D G All voltages are in V. Readings are taken with a 10 M digital multimeter. Readings are taken with a color-bar signal input. Voltage variations may be noted due to normal production tolerances. * : Can not be measured. Circled numbers are waveform references. s : B + bus. S : B – bus. Source Gate qf Transistor (FET) qg Transistor (FET) Source Drain Gate Transistor Emitter Collector Base qh – Drain One sheet of N board circuit diagram is divided into three sheets, each having the code N-a to N-c. For example, the destination ab1 on the code N-a sheet is connected to ab1 on the N-b sheet. a b 1 Ref. No. Circuit diagram division code 5-10 G S S D D G G S S Discrete semiconductot (Chip semiconductors that are not actually used are included.) • Divided circuit diagram 5-9 * Printed symbol Ver.1.6 (1) Schematic Diagram of A Board 8 9 D/A_4 NC D/A_5 VCC_5V GND D/A_3 2.9 SOG_OUT CLP SDA 23 4.9 VCC G_E.P. 2.7 G_OUT 79.0 GND 65.5 R_OUT B_OUT R_E.P. B_E.P 2.7 B_IN 2.6 2.7 58.1 KB GND KG GND KR GND HEATER + GND KB GND KG GND KR GND HEATER + GND 1 2 3 4 5 6 7 8 FC GND SK401 FC 11 10 G2 9 KR KG SG201 SG101 SG402 C417 4700p 2kV B R418 220k 1/2W (G2) 1 3 4 5 6 7 8 IC406 H8D2972 CUT OFF AMP R117 1M :CHIP D106 HSU83TRF R111 470 :CHIP 10 11 12 13 14 15 16 17 (G2) C115 0.1 250V G2 R118 1M :CHIP C120 0.1 250V R_CUTOFF C220 0.1 250V 1.2 1.2 1.2 5.8 5.8 5.8 105 103 109 107 103 101 1.7 C320 0.1 250V R404 2.2k :CHIP R405 680 :CHIP 5V FB102 D105 HSS83TD D107 HSU83TRF Q401 12V 2SC2412K DRIFT CORRECT 0.5 C464 0.01 B:CHIP +80V R220 470k :CHIP C440 0.01 B:CHIP FB403 1.1µH C442 0.01 B:CHIP C434 R414 1000p 47k 500V :CHIP B C433 12V 1000p 500V B C435 C437 0.01 470 B:CHIP 16V C444 11.9 1000p 500V Q407 B DTA114TUA FB411 1.1µH FB405 1.1µH 5V-2 R321 R320 470k 470k :CHIP :CHIP C467 1 250V R409 2.2M :CHIP R120 470k :CHIP D405 1SS119 PS401 1A L405 22µH 4.3 FB404 1.1µH BCI VS AVDD Hfly OVDD AV FBLK 10 DVSS BOUT XT0 PWM4 PWM0 PWM3 PWM1 PWM2 24 23 22 21 18 ROUT R119 15k :CHIP 17 11 XT1 R209 13k :RN-CP D203 1PS181-115 R228 4.7k :CHIP C208 0.1 R222 25V 22k B:CHIP :CHIP 16 15 Q301 2SC2412K BUFFER R454 2.2M :CHIP G2 CONT R451 560K :CHIP 2.7 6 5 C457 0.01 B:CHIP 8 C456 0.22 16V B:CHIP R464 2.2k :CHIP IC405(1/2) R450 NJM2904M(TE2) 4.7k G2 CONT :CHIP R461 R463 220k 100k :CHIP :CHIP C313 R309 0.22 13k 16V :RN-CP B:CHIP 5V 2.7 3.8 7 4 R230 470k :CHIP Q410 534 2SC5022-02 1 IC405(2/2) NJM2904M(TE2) G2 CONT R_BKG R219 15k :CHIP C308 0.1 R322 25V 4.3 22k B:CHIP :CHIP C314 0.1 25V B:CHIP R328 4.7k D303 :CHIP 1PS181-115 5V 4.9 R442 1k 12V :CHIP 4.3 R449 22k :CHIP 4.3 D403 MTZJ-T-77-39B 4.3 Q406 2SB709A G2 CONT R453 10k :CHIP A(VIDEO AMP,RGB OUT) R330 470k :CHIP B-SS9272<AEP>-A..-P1-EPS05 G_BKG R319 15k :CHIP B_BKG +5V +5V Schematic diagram 5-11 R459 10M :RN 12V 2 3 C213 0.22 16V B:CHIP G2 R455 100k :CHIP 1 2 R458 2.2M 1W :RN 4.9 0 12 3.5 5V C430 0.01 B:CHIP 19 GOUT 13 10 R457 10M :RN R460 10k :CHIP R128 4.7k :CHIP 5V C214 0.1 25V B:CHIP L404 100µH C423 47 25V C441 0.01 B:CHIP 20 9 DVDD 3 R419 220 :CHIP C415 0.22 16V B:CHIP 0 14 S R417 1M 2.3 :CHIP 2 4.3 B_IK 0 R412 220k :CHIP 1 G_IK 0 C432 0.22 16V B:CHIP X401 8MHz R130 470k :CHIP 4.9 4.3 3.4 C450 0.47 B:CHIP C114 0.1 25V B:CHIP 2SC2412K BUFFER R_IK 0.7 C425 100p CH:CHIP L403 100µH C446 47 25V C438 0.1 B:CHIP 25 GCI HS C113 0.22 16V B:CHIP 0.3 C426 100p CH:CHIP R406 100k :CHIP R109 13k :RN-CP D103 1PS181-115 A board , 5-12 STBY +5V 1W+5V GND +80V NC +220V NC +12V HEATER TO G BOARD CN652 CN406 2P WHT :VH G2 CONT 2.6 4.9 5V Q201 26 3 4 SCL 5 0.5 5V 4.3 6 R438 4.7k :CHIP C427 22p CH:CHIP RCI SDA 7 4.9 8 5V R122 22k :CHIP 28 27 1 2 ADCREF AGND 4.9 0.1 25V B:CHIP 1 2 3 4 5 6 7 8 9 4.3 R161 470 :CHIP OSCREF FB406 1.1µH 1.5KV 5V C108 Q101 2SC2412K BUFFER R261 470 :CHIP FILTER CN405 9P WHT-L :S-MICRO FB402 1.1µH R439 470 :CHIP C431 1000p B:CHIP 9 8 +220V R490 4.7k :CHIP R361 470 :CHIP IC404 CXD9514M OSD IMR 104 D205 HSS83TD 11.8 R436 2.2k :CHIP 6 G1 8 7 7 C436 0.22 16V B:CHIP R430 100 :CHIP C419 1000p 500V B 3 4 H1 4.7 5 H2 C424 1000p 500V B R218 1M :CHIP G1 G1 KB L402 22µH SG401 FV 13 1 5V R426 220k :CHIP C416 2.2 C215 0.1 250V FB202 R114 22 :CHIP 4.9 SCL D305 HSS83TD 1 2 3 4 5 6 7 8 TO D BOARD R315 47 1/2W SG301 :SURGE R215 47 1/2W :SURGE R115 47 1/2W :SURGE R217 1M :CHIP D206 HSU83TRF R137 470 D207 HSU83TRF +B C410 0.01 B:CHIP R138 47 :CHIP R110 100k :CHIP R491 4.7k :CHIP C315 0.1 250V D307 HSU83TRF B_CUTOFF 5V FB302 R214 22 :CHIP G_CUTOFF INPUT_SW B_DET_IN R314 22 :CHIP R210 100k :CHIP 2.7 +220V R317 1M :CHIP CN408 8P 522 82.6 35 34 32 31 ABL_IN FV :CHIP C463 0.01 B:CHIP (GND) CN407 8P D306 R311 R318 220 1M HSU83TRF :CHIP R113 47 :CHIP 29 28 GND1(B) R212 22 :CHIP R211 220 :CHIP R_OUT R_BASE G_OUT G_BASE B_OUT B_BASE 5V (GND) C109 12p CH:CHIP C458 0.1 :CHIP C462 0.1 C459 :CHIP 22 100V 2.7 12V R310 100k :CHIP R112 22 :CHIP +80V C209 10p CH:CHIP R238 R237 47 470 :CHIP C110 0.001 CH:CHIP 9 10 11 12 13 14 15 12V R407 470k:RN-CP R403 22k :CHIP 30 13 14 D/A_2 27 VCC2 C312 0.22 16V B:CHIP R402 1k :CHIP R213 47 :CHIP R216 4.7k :CHIP R312 22 :CHIP 8 R116 4.7k :CHIP 6 26 G_DET_IN NC BLK 7 12V 2.8 25 3.4 V_DET D/A_1 24 V_DET_C GND 15 GND OSD_B 16 R_DET_IN 23 2.7 4.3 6 R307 680 :CHIP C422 0.22 16V B:CHIP 0.7 17 VCC1 VCC2 0 C407 0.01 B:CHIP 18 G.DET 4.4 24 HOLD_CR2 25 0.6 GND 5 5 B_IK G_IK R_IK B_IN G_IN R_IN VBB GND VCC1(B)CONT_DAC B_OUT 2.7 R202 100k :CHIP VBB 41 40 39 38 37 36 B-IN 2.6 C420 0.22 16V B:CHIP 33 10 GND1(G) 11 HOLD_CR1 SYNC_SEP.OUT R488 47k :CHIP 2.6 12 G_BUF.IN 2.0 22 9 10 11 12 13 14 42 1 2 3 OSD_G Main_Brightness R415 100k :CHIP Q402 2SJ360-TE12L VCC KICK I 7 30 27 B_IN1 28 G_BUF.OUT 26 GND C206 1 10V B:CHIP 4 C309 C421 10p 0.01 B:CHIP CH:CHIP C210 0.001 CH:CHIP 12V VCC1(G)CONT_REF 0 GND C406 0.01 B:CHIP 5V D402 1PS184-115 GND 3 14 13 C BLOCK 3 2 C310 0.001 CH:CHIP 4.6 2.5 C413 0.01 B:CHIP R411 4.7k 5V :CHIP R441 1M :CHIP SOG_IN 8 B_OUT C212 0.22 16V B:CHIP C307 0.1 25V B:CHIP 12 +220V D406 1PS226-115 C449 1 B:CHIP NC 4 1 R316 4.7k :CHIP R207 680 :CHIP 2 R221 470k :CHIP R121 470k :CHIP D407 1PS226-115 H G_IN 9 G_IN1 VCC2 29 7 8 9 R_IN1 GND 18 1 R420 2 100 :CHIP R421 3 100 :CHIP 4 R422 5 100 :CHIP 6 R424 :CHIP 7 1k R428 :CHIP 8 100R427 1k :CHIP 9 10 R425 1k 11 :CHIP 12 R443 100 :CHIP 13 R444 100 :CHIP 14 15 R445 100 :CHIP 16 R446 100 :CHIP 17 18 R447 47 :CHIP 19 R448 47 :CHIP 20 R456 100 :CHIP 21 VDD A6 Y6 A5 Y5 A4 Y4 A1 Y1 A2 Y2 A3 Y3 GND R313 47 :CHIP 8 1 2 3 4 5 6 G ABL(NC) CLP GND C.BLK GND SYNC_ON_G G.SYNC_DET H.SYNC V.SYNC HFBP GND INPUT_SEL SCL SDA GND HS/CS 1 VS 1 DDC+5V 1 DDCSCL 1 DDCSDA 1 HOSTGND 1 TO N-a BOARD CN001 G_OUT 0.1 7 CN403 21P L-FPC F 4 6 GND 0.6 0.5 GND2 R107 C443 680 0.01 B:CHIP :CHIP 2.4 5V E GND1(R) 1 R337 470 2.6 31 6 VCC2 4.5 D OSD_R 5 36 35 33 32 34 1 2 3 4 5 C207 0.1 25V B:CHIP NC R338 47 :CHIP C411 220 16V 2.6 2.6 IC407 SN74HC04ANSR G SYNC BUFFER C112 0.22 16V B:CHIP R_OUT 19 C405 0.1 25V B:CHIP 2.7 VCC1(R) 0 VCC2 2.7 20 C408 0.01 B:CHIP R_IN 21 R431 470k :CHIP OSD_BLK 0 C216 0.01 B:CHIP 22 5V-2 5V 11 6 1 VCC2 G_OUT 21 12 7 2 C107 0.1 25V B:CHIP 2.6 20 INPUT (HD15) B_IN2 19 C 13 8 3 VCC2 GND 10 CN401 HD15D-SUB G_IN2 11 5 14 9 4 R_OUT 12 10 15 2.4 2.5 13 B VCC2 VCC2 14 C102 C201 47 0.01 25V B:CHIP R205 C205 47 0.01 :CHIP B:CHIP D301 G 1PS226-115 R201 C202 75 47 C301 C402 :RN 25V 0.01 47 B:CHIP R305 25V C401 47 10 :CHIP D102 B 1PS226-115 R301 C302 C103 75 R106 D202 47 0.01 :RN 47 1PS226-115 25V B:CHIP :CHIP R C203 R103 C104 47 0.01 75 D302 25V B:CHIP R206 :RN 47 1PS226-115 :CHIP C403 G 220p R203 C204 C303 CH:CHIP 75 47 0.01 :RN R306 25V B:CHIP 47 :CHIP R413 B R303 C304 C404 100k :CHIP 75 47 220p :RN 25V CH:CHIP R_IN2 15 R R101 75 :RN 6 5 4 3 2 1 NC NC NC NC NC NC D201 1PS226-115 +12V IC402 M52749FP-TP RGB DRIVE 5V 16 CN402 6P WHT :S-MICRO 5V D101 1PS226-115 C101 0.01 B:CHIP R105 47 :CHIP 17 A IC401 M52757FP-TP RGB DRIVE 11 IC403 FA4301 RGB AMP 12V 5V-2 10 95.6 7 6 VBB R_IN 5 GND 4 VBB 3 G_IN 2 2.6 1 G2 G2(NC) TO D BOARD CN506 GND2 (R) Vcc2 (G) OUTPUT (G) GND2 (G) Vcc2 (B) OUTPUT (B) GND2 (B) G Buffer out Sync SEP in Sync SEP out Vcc3 V-DET in3 GND4 V-DET in2 Vcc4 V-DET in1 V901 PICTURE TUBE 21TKC H OUTPUT (R) RCV IC401 M52757FP Vcc2 (R) • A BOARD 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 KB KR G2 G4 KG G1 GM G Sync Sepa HV R G B OR TO D BOARD T902(FBT)HV 5 6 7 8 9 10 11 12 13 14 15 16 VCC1 (R) 3 GND1 (R) 5 6 OSD IN (G) 9 INPUT (G) 6 VCC1 (G) 8 9 Vcc1 (G) Input1 (B) Vcc1 (B) Input2 (R) GND1 Input2 (G) GND5 Input2 (B) Sync DET1 Sync DET2 S-DET out Vcc5 Video DET-Hold Main Brightness Retrace BLK IN RETRACE BLANKING 41 RETRACE BLANKING 38 OUTPUT (G) RETRACE BLANKING 33 OUTPUT (B) OUTPUT (R) CLAMP F/B CLAMP SUB CONTRAST MAIN CONTRAST OSD MIX AMP CLAMP F/B OSD IN (B) 13 64.0 Vp-p (H) CLAMP SUB CONTRAST MAIN CONTRAST OSD MIX AMP VCC1 (B) 12 35 Contrast ref. CLAMP F/B GND1 (B) 16 0 INPUT (SOG) 2.2 Vp-p (8MHz) 7 31 Contrast cont. OSD LEVEL 4bit Main CONTRAST 8bit ABL IN 17 19 VCC=5V Sync On Green Sep B SUB CONT 8bit G SUB CONT 8bit R SUB CONT 8bit SOG Sep OUT 20 23 SDA BUS I/F DAC 22 SCL 5-13 14 Clamp Pulse IN GND 24 GND (5V) 21 1 25 26 27 28 29 5-14 32 36 39 GND2 64.0 Vp-p (H) AMP GND1 (G) 10 INPUT (B) 11 65.0 Vp-p (H) OSD MIX GND 8 64.0 Vp-p (H) MAIN CONTRAST GND 4.6 Vp-p (H) SUB CONTRAST D/A OUT1 5 4.8 Vp-p (H) CLAMP 30 D/A OUT2 7 2 34 D/A OUT3 66.0 Vp-p (H) 64.0 Vp-p (H) INPUT (R) 3 42 D/A OUT4 4 4 D/A OUT5 4.7 Vp-p (H) OSD IN (R) OSD BLK IN 2 18 IC402 M52749FP • A BOARD WAVEFORMS 1 17 SWITCH 4 V-DET out 3 VCC2 • A BOARD 2 Input1 (G) Input1 (R) 1 Vcc1 (R) G DET B-SS9272<AEP>-A..-P2-EPS05 (a) — A BOARD (Conductor Side) — 1 2 3 VIDEO AMP RGB OUT • A BOARD SEMICONDUCTOR LOCATION — A BOARD (Component Side) — 1 2 IC Component ( Conductor Side ) ( Side ) IC401 IC402 IC403 IC404 IC405 IC406 IC407 A A-2 A-3 B-3 B-2 A-2 C-3 D-2 A-1 D-2 A TRANSISTOR Component ( Conductor Side ) ( Side ) Q101 Q201 Q301 Q401 Q402 Q406 Q407 Q410 * C-1 C-1 C-1 A-3 D-3 D-3 D-3 D-2 D-1 1 1 1 1 qg 1 2 – DIODE B Component ( Conductor Side ) ( Side ) D101 D102 D103 D105 D106 D107 D201 D202 D203 D205 D206 D207 D301 D302 D303 D305 D306 D307 D402 D403 D405 D406 D407 C * 6 B-1 B-3 A-3 A-1 B-1 A-2 A-2 B-1 B-3 A-3 A-1 A-1 A-1 A-2 B-1 A-1 A-3 A-1 A-1 A-1 A-3 A-2 D-3 D-2 D-2 D-3 A-2 D-1 7 qa – 3 3 6 7 qa – 3 3 6 6 qa – 3 3 9 – – 6 6 B C CRYSTAL Component ( Conductor Side ) ( Side ) X401 C-2 C-2 *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-10) D D NOTE: The circuit indicated as left contains high voltage of over 600 Vp-p. Care must be paid to prevent an electric shock in inspection or repairing. Schematic diagram < (a) board 5-15 5-16 3 H (2) Schematic Diagrams of H, J Boards 1 2 3 4 5 6 7 USER CONTROL 8 J 9 10 POWER SW 11 12 A Q803 DTA124ESA-TP LED DRIVE 1W+5V 4.9 C810 10 16V 4.9 2.2 Q804 DTA124ESA-TP LED DRIVE R824 0.2 B R823 1k CN891 3P WHT :VH R813 22k Q801 2SC3311A 1.5k LED DRIVE STBY+5V CN801 11P WHT-L :S-MICRO R811 10k 4.4 0 1 2 3 4 5 6 7 8 9 10 11 R812 10k 3.7 0.1 R822 470 G D801 SPR-325MVW POWER C R806 4.7K R807 10k S807 H+ D Q802 2SC3311A LED DRIVE R R821 150 S806 H- R804 2.2K R805 2.2K S805 MENU S804 V+ R802 1K R803 1K S803 V- S802 ASC R801 4.7K LED0 LED1 KEY_DET NC GND 1W+5V STBY+5V ENV_DRI GND GND GND TO G BOARD CN603 J (POWER SW) TO N-a BOARD CN007 B-SS9116<NH.>-J.. TO CRT SHIELD S801 RESET TH801 10K H(USER CONTROL) S891 POWER AC L OUT 1 NC 2 AC L IN 3 R814 100k R815 10k C814 47 16V B-SS9272<AEP>-H..-EPS05 E F — H BOARD — — J BOARD — G H I J 5-17 5-18 13 14 (3) Schematic Diagram of D Board 5 7 6 8 H I R932 1k :CHIP C925 47 -15V R933 C922 0.1 33k :RN-CP 100V :PT C701 22 100V R719 3.3k :RN-CP C706 0.1 25V B:CHIP C712 0.22 100V :PT R727 1 :FPRD 2 OUT D710 HZS5.1NB2 R716 39k :CHIP 1.7 R720 R721 10k 10k :CHIP :CHIP D706 EGP10PKG23 Q707 R713 2SC4634LS-CB11 V DRIVE 2.7k Q706 2SA1037AK V DRIVE :CHIP 4 + 6 Vcc D510 HZS5.1NB2TD +VIN -VIN VEE OUT VCC D515 HZS5.6NB2TD C710 220 35V :HT ABL C567 R559 2200p 10k R941 B:CHIP :CHIP 100 :CHIP 5.0 0 0 7 6 5 4 3 2 5 R582 100 1/2W :RN IC503 BA10324AF AMP 1.8 1.8 1.1 R1505 4.7k :RN-CP R725 1.8 1/2W :RN 4.8 S 0 4.8 S R522 R514 C519 R537 C517 R530 100k C505 47k 0.01 47k 0.01 1k :CHIP 0.01 B:CHIP :CHIP R531 B:CHIP B:CHIP 100k R1506 R513 R526 R524 :CHIP 1k 1k 100k 1k :CHIP :CHIP :CHIP :CHIP R504 1k :CHIP 4.8 S 1.1 3 0 C557 R538 C526 R542 47k 0.01 1k 0.01 B:CHIP:CHIP R539 B:CHIP 100k R1507 :CHIP 100k :CHIP 0 Q513 2SK3262 S-CAP CHANGE S 0 1 R501 47 2W :RS 0.01 :PT C531 0.1 250V :PP R587 100 2W :RS T505 HLC RY501 R584 47k R512 22k :RN S 1 D517 ERA91-02TP1 4 Q512 2SK3262 S-CAP CHANGE R726 1.8 1/2W :RN Schematic diagram < H J boards D board , 4 2 Q518 2SD2394-EF HL OUT Q516 0.5 2SB1565EF HL OUT Q523 2SC2412K C566 C528 0.22 250V :CQ T503 HST 1 2 3 4 5 6 7 8 9 10 3 C572 0.001 B:CHIP R1510 10k :CHIP R591 100 2 R594 C538 R567 R580 100 100 22k 0.01 :RN-CP B:CHIP 1/2W 1/2W :RN :RN R598 10k :RN-CP C565 R599 0.1 1.8k R503 25V 1k B:CHIP :RN-CP:CHIP 9 10 11 12 13 14 0 0 8 3 4 5 R940 10k :CHIP 1 O2 -2 +2 VCC +1 -1 O1 2.5 Q524 2SA1037AK PIN AMP D512 4.4 1SS355TE-17 +15V 4.8 S 0 R505 1k :CHIP R515 1k :CHIP TH501 TH502 1.2 R728 220 1W :RS D708 GP08DPKG23 D707 HZS5.1NB2TD CN509 10P :VH VV+ 7.7 C568 C577 0.047 B:CHIP R510 10 C536 47 10k :RN-CP C562 0.01 B:CHIP R595 2.2k :CHIP C537 C544 0.056 400V Q517 0.027 :PP 2SK3262 400V R583 47k C550 0.15 400V S-CAP CHANGE S 0 D516 1SS133T-77 L503 1mH R577 33 1/2W :FPRD S R551 R563 1k 1k :CHIP :CHIP R552 C535 R558 R565 C542 R573 R545 C530 R548 100k 100k 0.01 47k 0.01 47k 100k 0.01 47k :CHIPB:CHIP :CHIP B:CHIP :CHIPB:CHIP V- C711 6800p B:CHIP C707 C709 R724 0.01 2.2k 0.1 B:CHIP :RN-CP :PT HCENT HSPBAL ABL_DET C545 22p 500V CH C555 2.2 250V C556 1.2 250V :PP L504 4.7mH R581 100 R588 68 1/2W 1/2W :FPRD C559 14.7 2.2 0 250V R585 10k :CHIP V+ UP OUT 7 5 Schematic diagrams 5-19 C512 220p CH:CHIP D522 D504 1SS355TE-17 1SS355TE-17 S C560 0.01 B:CHIP Q519 DTC114GKA RELAY DRIVE D(DEFLECTION) 0.6 1.1 1.1 R711 C720 R717 10k 1k 10 :CHIP :CHIP R536 C504 22k 4700p :RN-CP B:CHIP C561 47 25V 7.7 R543 R517 C525 R1518 12k 33k 100 0.047 :CHIP :RN-CP :RN-CP B:CHIP R541 R518 R1503 R1504 C575 3.9k 0 47k 20k R597 0.01 :RN-CP :RN-CP :RN-CP CH:CHIP 10k :CHIP :CHIP C527 0.01 B:CHIP R521 C508 4.7k 22 :RN-CP 0 13.9 1.8 -13.4 400V R732 470k 198.1 1/2W :SURGE C704 470p 2kV B R511 4.7k :CHIP R507 C501 100k 0.01 :CHIP B:CHIP OUT VEE Vcc 1 3 1.1 VSHAPE R729 1 1/2W :FPRD C713 1000 25V IC701 LA7841L V DY OUT PUMP R710 10k :CHIP C574 4700p B:CHIP C564 C551 1 4700p B:CHIP D923 1SS355TE-17 R575 7.5k :RN-CP C521 C509 Q501 Q511 Q510 Q506 Q525 0.39 2SK3262 0.82 Q507 2SK3262 2SK3262 2SK3262 2SK3262 2SK3262 250V S-CAP S-CAP CHANGE 250V S-CAP S-CAP CHANGE :PP S-CAP S-CAP CHANGE :PP CHANGE CHANGE CHANGE 28.5 -0.1 1.8 R723 3.3k :RN-CP R709 1k :CHIP R528 1SS355TE-17 12k :RN-CP R519 22k :CHIP HVDET HLIN R722 1 1/2W :FPRD C708 1000 25V HFBP VRET D520 C933 1 R718 18k :RN-CP R714 2.2k :CHIP R570 2.2k 1/2W :FPRD -15V -15V +15V C529 100 25V ABL R934 C903 10 4.7k :RN-CP DGUS HD 1 2 3 4 5 6 7 8 9 D519 1SS355TE-17 C921 0.22 100V :PT R571 4.7k R527 R556 8.2k 22k :RN-CP :RN-CP Q526 DTA143TKA GAIN SW R593 10k :CHIP 18 17 16 15 14 13 12 11 10 IC501 BA9759F PIN CONTROL R928 R930 5.1k 1.2k :RN-CP :RN-CP 7 +15V R576 1k 1W :RS 15V R701 2SC2362KG 1k H DRIVE :CHIP R731 R704 1.8 2.7k 1.5k :CHIP :RN-CP HTR C563 1500p B:CHIP C548 470p 2kV B S5 Q703 2SA1049 H DRIVE R578 1k :CHIP D513 1SS133T-77 27.4 R708 15 2W :RS 28.9 10 D514 1SS133T-77 R579 1k :CHIP R586 22k :RN-CP 0.7 28.1 Q705 2SA1358 H DRIVE 5 C554 100p 2kV :HR 0.1 Q520 2SC2412K BUFF 4 C546 100p 2kV :HR C547 1500p 630V :PP D511 FMQ-G5GS 2 8 2 1 T502 HCT R1517 47k :CHIP S6 R707 4.7 :FPRD C511 68p CH:CHIP C524 470p CH:CHIP C515 0.01 B:CHIP 1.2k D910 :RN-CP 1SS133T-77 R922 4.7 :FPRD 12 11 10 9 2 3 4 5 Q701 ECO C516 470 16V D913 1SS133T-77 R534 39k :RN-CP R920 47k :CHIP D912 EGP10GPKG 2 C571 10p CH:CHIP C543 3600p 1.8kV R546 0.22 3W :RS 3 R533 1 1/2W :FUSE C520 1000 25V 8 6 6 29.6 29.5 2.5 R921 10k 1 R535 4.7k :CHIP R931 D914 1SS133T-77 T701 DFT 12 D915 0 HZS33NB2TD Q908 DTC114GKA HV DET C926 10 11 R529 2.2k R523 0.47 220 :CHIP Q503 :MPS :CHIP C518 2SA1036K 0.47 H DRIVE :MPS 1 5 4 R566 R569 R564 33k C541 47k 12k 2200p :RN-CP :RN-CP :RN-CP B:CHIP R557 27 1W :RS 28.4 14.7 9 10 C506 4.3 :PT R532 33 1W :RS O3 -3 +3 VEE +4 -4 O4 R937 4.7k :CHIP +12V R706 4.7 :FPRD 29.3 R590 2.2k :CHIP R502 2.7k :CHIP C924 R935 0.1 47k 100V :CHIP :PT 16 7 3 5 82.5 75.5 R715 4.7 :FPRD Q515 2SC5570 H OUT 528 -0.9 D508 D5SC4M T501 HDT C703 2200p 1kV :E R572 0.47 C549 0.1 3W :PT C532 R555 R562 10k 12k 0.001 B:CHIP :RN-CP :RN-CP R544 1k :CHIP C702 47 100V Q704 2SC3421 H DRIVE R705 470 :FPRD R924 10k :CHIP Q509 2SC3746 C522 H OUT 4700p :PT D5061.8 C523 1SS133T-77 4700p -14.4 4.3 4 FC FC TO A BOARD 18 1 Q514 2SC3209LK H CENT 4.5 S0 HDF C916 2000p 1.2kV :PP 8 14.7 FB507 1.1µH S1 D703 1SS133T-77 C715 0.1 25V B:CHIP S 3 C540 0.001 200V :PT 5.0 D509 1SS133T-77 S5-1 Q702 2SC2459 H DRIVE D701 1SS133T-77 S1 D907 HZS16NB2TD R939 1k :CHIP R703 39k :RN R730 10k :CHIP Q906 2SK2655 HV OUT 5 C918 4700p 100V :PT C917 0.33 250V :PP Q907 DTA114GKA HV DET 31.4 R509 1k :CHIP C513 4700p B:CHIP 9.4 C558 100 25V R702 10 :FPRD S2 6 Q904 2SA1036K HV DRIVE +80V S5-1 2 2 R916 22 :FPRD 8.2 D921 1SS355TE-17 R925 330k 1/2W :RC C923 SG901 3300p FV TO 200V FV A BOARD :PT SG903 R927 14 1k 1/2W :RC R926 15 1k 1/2W SG902 :RC R918 68 :10W 192 8.3 S4 S3 S5 RV901 100k HD D909 C920 0.022HZS16NB2TD :PT C539 4700p B:CHIP C534 220 R561 25V 8.2k :HT :RN D709 ERA22-06AVRBT 4 ≠≠ S5 ≠ TO N-a BOARD CN011 1 8.9 VDF G 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R923 270k :RN-CP C507 0.22 :MPS 9.0 R912 1k :CHIP D702 1SS133T-77 R929 10k :RN-CP R919 4.7k 1/2W :RC L902 15µH 6 D906 YG911S3R Q903 2SC2411K C915 HV DRIVE 0.22 :MPS C914 C912 0.047 0.047 200V 200V :PT :PT 29.9 TH DET S4 S3 S5 S2 STBY+5V S1 1W+5V GND ECO SW GND PWR SW GND DGUS SW GND HTR SW GND HFBP GND HD GND +12V VRET GND VSHAP 8 D904 1SS355TE-17 THDET HV 17 217 R911 470 :CHIP 6 -7.6 1 9 13 R914 22 CN505 25P :FFC TO PICTURE TUBE HV 10 5 25 24 23 22 21 TXD 20 19 RXD 18 17 16 15 HDF 14 13 VDF 12 11 10 ABL_DET 9 HVDET 8 S0 7 HCENT 6 S6 5 4 HSPBAL HLIN 3 HSIZE 2 HSP 1 5 R547 2.2 10W :RN S3 F HV ADJ T902 :FBT FB901 1.1µH R915 4.7k :CHIP D507 YG911S3R +12V Q502 R508 2SC2412K 220 H DRIVE VCC TO N-a BOARD CN010 +220V R550 0.47 1/2W :FPRD 4 R1515 47 3W :RS HSP HSIZE D923 1SS355TE-17 VSHAPE VRET E Q505 2SA1036K PIN DRIVE +15V S4 C913 33 400V CN504 25P :FFC +15V +15V -15V -15V GND TXD GND RXD GND STBY+5V GND HDF GND VDF GND ABL GND HV DET S0 HCENT S6 HSPBAL HLINBAL HSIZE HSHAPE +15V D919 1SS133T-77 15 400V 82.0 2 R554 15k :RN-CP R904 R906 220 220 :CHIP :CHIP Q905 T901 2SJ569LS HRC D905 HV REG SW 1 147 HZS13NB2TD R908 6.8 3W L901 :RS 100µH HCENT L 82.5 R568 3.9k :CHIP 78.4 R540 47 3W :RS 200V :PT 200V :PT D902 HZS12NB2TD 9 L502 2.2mH FB502 1.1µH D505 HZS13NB2TD C514 C573 9.0 R520 0.022 0.022 22 2 D R1501 1k :CHIP +B RXD TXD C502 0.22 :MPS 3.1 D920 C931 10 R907 22k :CHIP 2 9.1 HZS4.7NB2TD 161 G ≠≠ S5 ≠ 9 10 10 HCENT N D R525 4.7k :CHIP C533 220 25V :HT 218 C908 0.01 B:CHIP 0 1 3.3 8 Q508 2SJ569LS PIN OUT S Q504 2SC2411K PIN DRIVE R1502 220 :CHIP C927 47p CH:CHIP FB501 1.1µH S2 7 C510 33 250V L501 100µH 9.0 9.0 6 14 13 R574 C552 IC502 LA6500-FA 100k 0.01 H CENT OUT :CHIP B:CHIP R560 10k :RN-CP R553 220 +90V L505 HOC C930 10p CH:CHIP R902 680k :RN-CP R549 0.47 1/2W HCENT H :FPRD 2.0 5 C905 270p CH:CHIP C902 100 25V 4 D918 1SS133T-77 1 2 3 4 180p CH:CHIP C928 470p CH:CHIP 2.5 3 9.3 9.1 C901 0.01 B:CHIP DGUS HTR 2 C919 4700p 2kV :E S TO ECS 1 D917 +15V 1SS355TE-17 ECO CN503 4P WHT GND STBY+5V RXD TXD R943 4.7k :CHIP R917 220 1/2W :FUSE R945 100 :CHIP - C TO G BOARD CN650 C935 1000p CH:CHIP 9.0 IC901 BA9758FS HV CONTROL 1 2 3 4 5 6 7 D908 ERA34-10TP1 20 19 18 17 16 15 14 13 12 11 CN502 7P WHT :S-MICRO STBY+5V 1W+5V ECO SW PWR SW DGUS SW HTR SW GND 2.5 FB504 1.1µH R903 47k :CHIP C910 C932 3.3 0.01 B:CHIP C929 0.1 25V B:CHIP 9.0 TO G BOARD CN653 FB503 FB506 FB505 1.1µH 1.1µH 1.1µH 1 2 3 4 5 6 D922 ERA34-10TP1 D901 1SS133T-77 SVcc VREG9 PVcc NC AGC PWMOUT PGND SAWOUT HVD NC HVDCAP SGND 3.2 NC HDIN SLOW SW3.5 DELAY NC 8.9 + ERROUT B +12V +15V GND -15V GND +80V C909 470 16V 2.0 C907 CN501 6P WHT :S-MICRO 12 CN508 8P WHT :S-MICRO 2.5 R901 100k :CHIP 11 8 7 6 5 4 HCENT L 3 HCENT N 2 HCENT H 1 CN506 2P WHT :VH 1 2 G2 G2(NC) A 10 TO G BOARD CN654 GND GND NC +220V +220V H CENT L H CENT N H CENT H TO A BOARD CN406 9 HFBP 4 SAWR PWMOUT3.6 SAWOUT PGND SGND SLOW SW 6.8 HDIN ERRIN NC 2.5 REFIN MIX+ NC 2.5 MIXERROUT MIXOUT 3 PVCC 2 VREG9 1 Q521 Q522 2SC2412K 2SC2412K TH DET TH DET R516 1k R506 1k :CHIP B-SS9194<U/C>-D..-EPS05 :CHIP THDET R589 2.2k :CHIP C503 0.01 B:CHIP 5-20 GND V.DY V.DY NC H.DY H.DY NC NC H.DY H.DY C H C C H.DY FASTEN H H V.DY (d) • D BOARD WAVEFORMS — D BOARD — 2 1 8.8 Vp-p (H) 3 5 50.6 Vp-p (H) 1 2 3 4 568 Vp-p (H) 1.9 Vp-p (H) 4 DEFLECTION 6 54.5 Vp-p (H) A 2.1 Vp-p (H) • D BOARD SEMICONDUCTOR LOCATION IC IC501 IC502 IC503 IC701 IC901 DIODE C-4 A-1 C-4 A-5 C-1 TRANSISTOR Q501 Q502 Q503 Q504 Q505 Q506 Q507 Q508 Q509 Q510 Q511 Q512 Q513 Q514 Q515 Q516 Q517 Q518 Q519 Q520 Q521 Q522 Q524 Q525 Q526 Q701 Q702 Q703 Q704 Q705 Q706 Q707 Q903 Q904 Q905 Q906 Q907 Q908 B-5 A-4 A-4 C-4 D-4 B-5 C-5 A-2 A-4 C-5 C-5 C-5 C-5 B-2 A-3 B-4 D-5 B-4 D-4 B-5 B-5 C-5 B-3 C-5 C-4 D-4 D-3 D-4 D-3 D-4 D-3 D-3 B-3 C-3 C-3 C-3 B-2 B-2 *– 1 1 1 1 – – – – – – – – – – – – – 1 1 1 1 1 – 1 – – – – – 1 – 1 1 – – 1 1 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D514 D515 D516 D517 D519 D520 D522 D701 D702 D703 D706 D707 D708 D709 D710 D901 D902 D904 D905 D906 D907 D908 D909 D910 D912 D913 D914 D915 D917 D918 D919 D920 D921 D922 D923 D-4 A-1 A-4 A-2 A-3 B-2 A-1 A-2 B-3 B-2 B-3 B-2 B-4 B-3 C-4 D-4 C-4 D-4 D-4 D-4 D-2 A-5 A-5 B-2 D-3 B-1 B-2 B-3 C-3 C-3 B-3 C-3 C-1 C-2 C-2 B-1 C-2 C-2 B-2 B-1 B-1 B-1 B-2 C-3 C-4 * 3 – – – – – – – 3 – – – – – 3 3 3 – – – – – – – – – – 3 – – – – – – – – – – 3 – – – 3 – 3 B C D VARIABLE RESISTOR RV901 NOTE: The circuit indicated as left contains high voltage of over 600 Vp-p. Care must be paid to prevent an electric shock in inspection or repairing. B-1 *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-10) 5-21 5-22 5 • Divided circuit diagram ABL(NC) CLP GND C.BLK GND SYNC_ON_G G.SYNC_DET H.SYNC V.SYNC HFBP GND INPUT_SEL SCL SDA GND HS/CS 1 VS 1 DDC+5V 1 DDCSCL 1 DDCSDA 1 HOSTGND 1 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R021 100 :CHIP R020 100 :CHIP R019 100 :CHIP CBLK CLP R1006 1k :CHIP R1007 1k :CHIP R048 1k :CHIP SOG SOGDET HSOUT1 VSOSD R022 100 :CHIP INPUTSEL SCL SDA D014 1PS184-115 R007 2.2k :CHIP R008 2.2k :CHIP C001 0.001 B:CHIP R009 2.2k :CHIP 6 5 R010 2.2k :CHIP C002 0.001 B:CHIP 7 R052 15k R051 :CHIP 15k :CHIP 8 4 IC012 24LC21AT/SN ROM 3 5 8 2 9 1 11 C009 C010 0.1 B:CHIP 47 12 10 13 4 7 8 6 9 6 7 R011 4.7 :FPRD R012 47 :CHIP R013 47 :CHIP D001 1PS226 D002 1PS226 D003 1PS226 D004 1PS226 D015 1PS184-115 R054 15k :CHIP R014 1k :CHIP 6 5 R1058 10k :CHIP R1059 1k :CHIP R1054 10k :CHIP R1056 10k :CHIP R004 R003 100 100 :CHIP :CHIP 7 4 R055 15k :CHIP 8 3 IC011 24LC21AT/SN ROM 2 R1063 4.7k :CHIP 1 R1049 4.7k :CHIP C087 10 D022 1PS184-115 C084 10 23 22 21 16 19 18 20 17 C069 0.1 B:CHIP D005 D006 D007 D011 D012 D010 D009 D008 R1052 10k :CHIP R1053 1k :CHIP R1057 1k :CHIP R1055 1k :CHIP HZS5.6NB2TD HZS5.6NB2TD HZS5.6NB2TD HZS5.6NB2TD HZS5.6NB2TD HZS5.6NB2TD HZS5.6NB2TD HZS5.6NB2TD HOST G 1 HOST G 2 HC1 HS/CS1 HC2 HS/CS2 VC1 VS1 VS2 VC2 DSCL2 VC2 DSDA2 DSDA1 DSCL1 D020 1SS355TE-17 R045 ECO SOGDET ECO_SW HDSW VCC+4.5V HC1 VC1 HC2 OFFDET Q004 DTA124EUA ACTIVE OFF DET C082 47 25V R1070 C085 2.2k 0.01 :CHIP B:CHIP Q006 DTC123EKA ACTIVE OFF DET D038 UDZ-TE-17-2.2B Q007 R1045 4.7k Q005 DTC124EKA ECO SW DTA114GKA :CHIP ACTIVE OFF DET C012 R053 C011 0.1 47 4.7k :CHIP B:CHIP R1050 10k :CHIP D021 1SS355TE-17 D023 1PS184-115 R1051 100k :CHIP D024 1PS184-115 24 15 R044 1.8k :RN-CP 1k Q011 2SA1037AK :CHIP HD SW -15V +15V ac1 ab7 ab6 ab5 ab4 (n)-a board , R025 100 :CHIP -15V +15V R050 47k :CHIP 14 5 IC005 SC74AHCT74PWR ECO DET 4 10 3 11 2 12 1 C083 0.01 B:CHIP 13 3 14 2 IC004 SC74AHCT74PWR ECO DET 1 R059 2.2k :CHIP C099 0.1 25V B:CHIP 25 14 R1023 2.2k :RN-CP R075 270 :RN R076 270 :RN C064 R1047 C1005 3300p 10k 470p C065 25V :CHIP B:CHIP Q001 Q003 CH:CHIP 1 Q002 2SA1037AK 2SA1037AK 2SA1037AK R060 C068 2.2k CURRENT CURRENT CURRENT 0.22 :CHIP MILLER MILLER MILLER :MPS R1027 R1026 R063 R064 R062 2.2k 330k R058:CHIP 27 27 27 :CHIP 5.6k :RN-CP :RN-CP :RN-CP :CHIP C063 C070 C066 R1028 2200p C071 1000 2200p 680 CH:CHIP680p 16V CH:CHIP :RN-CP B:CHIP 26 27 13 28 12 29 11 9 10 8 R1022 2.2k :RN-CP ab3 Schematic diagram R026 100 :CHIP R006 100 :CHIP R005 100 :CHIP TXD RXD VDF ABLDET D037 HZS5.6NB2TD D036 HZS5.6NB2TD R015 4.7 :FPRD R016 47 :CHIP R018 1k :CHIP R017 47 :CHIP R039 100 :CHIP R040 100 :CHIP R031 5.6k :RN-CP R032 3.9k C091 100 16V L002 100µH C089 0.01 B:CHIP 30 7 31 C094 0.1 C067 25V 0.1 B:CHIP 25V B:CHIP 32 6 MOIRE R030 1k PWR_SW DGS PRT_DET ECO_SW S1 THDET S4 S3 S5 S2 :CHIP :RN-CP HVDET R1029 100 :CHIP S0 HCENT R1025 100 :CHIP S6 HSHPBAL R1040 100 :CHIP HLINBAL HSIZE HSP R034 1k :CHIP R1032 100 :CHIP R1033 100 :CHIP R1031 100 :CHIP R1034 100 :CHIP R1030 100 :CHIP R1035 100 :CHIP R1037 100 :CHIP R1038 100 :CHIP HTR R024 100 :CHIP R1041 100 :CHIP 33 5 SDA IC010 LA7865M-TLM H.V.OSC,AFC, H.DRV,V.SHAPE R1039 100 :CHIP 34 4 35 3 SCL VSS NC 36 2 C079 C080 0.01 47 B:CHIP NC NC NC L003 1000µH VRET 1 C078 0.22 :MPS VCLK NC R1043 100 :CHIP R1042 100 :CHIP ENV KEYDET INPUT_SW LED1 D018 HZS5.6NB2TD D025 1PS226-115 LED0 D026 1PS226-115 VCC NC C072 C073 0.1 1000 25V B:CHIP ab2 ab1 -a N (H.OSC,V.OSC,AFC,H.DRV,V.SHAPE) I NC REG9V VCC12 GND HD FILTER HD_DUTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 R081 1k :CHIP R082 1k :CHIP R047 1k :CHIP R085 1k :CHIP FB002 FB001 1.1µH 1.1µH R086 1k :CHIP FB003 1.1µH VCO_C +15V +15V -15V -15V GND TXD GND RXD GND STBY+5V GND HDF GND VDF GND ABL GND HV DET S0 HCENT S6 HSPBAL HLINBAL HSIZE HSHAPE TH DET S4 S3 S5 S2 STBY+5V S1 1W+5V GND ECO_SW GND PWR SW GND DGUS SW GND HTR SW GND HFBP GND HD GND +12V VRET GND VSHAPE 1 2 3 4 5 6 7 8 9 HFREQ C074 C075 680p 100p CH:CHIP CH:CHIP R1024 18k :RN-CP C077 0.1 B:CHIP HSDLY 5-24 5-23 AFC_FIL HPLL +12V STBY+5V H AFC_SW AFCSW 2Q HPHASE CN001 21P :FFC LED0 LED1 KEY DET NC GND 1W+5V STBY+5V ENV_DRI GND D017 HZS5.6NB2TD STBY+5V VSOSD G HS B-SS9272<AEP>-N..-P1-EPS05 NC NC NC NC NC NC NC NC F GND VCC12 8 7 6 5 4 3 2 1 NC SDA VSS HPHASE GND GND HSOUT VSHAPE CN002 8P :S-MICRO FBP_DLY1 IREF_R HPLL HFREQ SCL NC FBP HFBP 2Q 1Q 2Q 1Q E VSHP_C VSH VSH VDC 2Q 2PR 1Q VSAWRST VSAWRST FBP_DLY VCC VCLK NC 2CK 1Q 2PR 1PR 2CK 1PR DVSHAPE VDC VCC4.5 14 13 12 11 10 9 8 NC 2D NC DVSHAPE 1CK VSHPLVL 1W+5V 2CLR 2D 1CK 2CLR 1D VCC 1D S/HC VSHPLVL NC SUB+5V 1CLR VCC 1CLR D Circuit diagram division code R1061 10k :CHIP 1W+5V C D016 HZS5.6NB2TD B Ref. No. ab1 on the code N-a sheet is connected to ab1 on the N-b sheet. CN010 25P FFC CN007 9P WHT :S-MICRO A TO A BOARD CN403 TO D BOARD CN504 CN011 25P FFC TO D BOARD CN505 TO H BOARD CN801 7 6 5 4 3 2 1 each having the code N-a to N-c. For example, the destination (4) Schematic Diagrams of N (a, b, c) Board a b 1 One sheet of N board circuit diagram is divided into three sheets, ab7 ab6 +15V C096 0.01 B:CHIP C008 0.1 25V B:CHIP R1067 2.2k :CHIP 8 7 6 5 R1064 1k :CHIP Vcc 0 - + 1 2 3 R080 0 :CHIP 4 0 - + VDD R079 0 :CHIP D028 1SS355TE-17 C095 2200 10V R1068 2.2k :CHIP C028 3p CJ:CHIP R078 1M :CHIP X001 24.756MHz R023 4.7k :CHIP C029 39p CH:CHIP C1007 0.1 B:CHIP R1071 22k :CHIP C041 10 C040 10 C039 10 C038 10 R1021 4.7k :CHIP R1020 4.7k :CHIP EEPWC HOST G2 HOST G1 R1015 1k :CHIP R1062 1k :CHIP C1004 0.01 B:CHIP C037 10 C036 0.022 B:CHIP C5008 47 25V R5003 0 :CHIP 14 13 12 11 10 9 GS5001 3 4 C5005 47 25V R5010 0 :CHIP 1 2 5 7 8 6 8 7 GEOMAGNETIC SENSOR R5005 22k :CHIP C5009 0.1 25V B:CHIP R5006 R5007 1k 10k :CHIP :CHIP 2 R5011 10k :CHIP 3 R5015 C5004 C5003 C5002 100 47 10 1k 16V :CHIP 25V 4 6 R037 10k :CHIP 5 1 C023 0.01 B:CHIP R056 10k :CHIP R057 10k :CHIP C006 C013 C014 0.01 22 22p CH:CHIP B:CHIP 2 C027 0.1 B:CHIP 8 3 7 4 C007 R066 22p 1k CH:CHIP :CHIP R077 10k :CHIP R084 10k :CHIP 6 IC002 MM1170BFB WDT 5 +15V STBY+5V VY VX HDSW LED1 LED0 ECO INPUT_SW PRT_DET D013 HZS10NB2TD R029 10k :CHIP R067 10k :CHIP C024 C025 0.001 2200p B:CHIP B:CHIP C003 0.01 B:CHIP C053 0.01 B:CHIP Q008 DTC114GKAT146 SW C033 C026 100 0.01 25V B:CHIP R049 10k :CHIP R035 4.7k :CHIP C086 0.01 B:CHIP R1069 1k :CHIP IC003 M24C16-MN6T EEP ROM A0 R1066 10k :CHIP C090 0.01 B:CHIP C1003 47 25V WDP STBY+5V C042 0.01 B:CHIP C043 22 P82 SDA1 SCL1 GND1 P50/X1OUT VDD2 RESET P90 P55/INT5 P54/INT4 P53/INT3 P52/INT2 P51/INT0 TEST ICE P35/SCOUT P34/CLK P33/WR P32/RD P47/D7 VDD1 P46/D6 P45/D5 P44/D4 P43/D3 P42/D2 P41/D1 P40/D0 P31/CSIO P30/A8 P17/A7 P16/A6 P15/A5 P14/A4 P13/A3 P12/A2 P11/A1 P10/A0 MVBIAS VPP R091 1k :CHIP 158 GND20 D027 1SS355TE-17 157 UPWM22 R1065 1.5M :CHIP C031 10 R093 R092 1k 1k :CHIP:CHIP 155 VDD17 R095 R094 1k 1k :CHIP:CHIP 154 VDD16 VCC TC C022 0.01 B:CHIP C021 0.01 B:CHIP 148 UPWM17 R1017 1k :CHIP R042 10k :CHIP C051 0.01 B:CHIP 147 VDD15 R1016 1k :CHIP R1004 1k :CHIP C050 10 C045 0.022 B:CHIP C046 0.022 B:CHIP C047 0.022 B:CHIP C048 0.01 B:CHIP C049 10 146 VDD14 VX VY 139 VDD13 R097 R098 R096 4.7k 10k 10k :CHIP :CHIP :CHIP 137 VDD12 A1 RESET HVDET 134 GND14 A2 NC C015 0.01 B:CHIP C016 0.01 B:CHIP C017 0.01 B:CHIP C019 0.01 B:CHIP 130 GND13 WC CK VS THDET ABLDET C020 AIN5 AIN6 AIN7 AIN8 AIN9 AIN10 AVDD2 AIN11 AIN12 AIN13 GND5 INT1 P92 P93 P94 P95 P96 UOUT7 UOUT8 VDD3 VDD UBI5 UIN1 UIN2 GND6 UIN3 UIN4 UIN5 UIN6 GND7 UPWM1 VDD5 VDD6 UPWM2 GND8 GND9 UPWM3 VDD7 VDD8 UPWM4 129 GND12 SCL RCT R061 1k :CHIP CLPDLY R090 10k :CHIP HPHASESW R1018 1k :CHIP VRET C018 0.01 0.01 B:CHIP HTR B:CHIP R1036 PWR_SW 100 :CHIP DGS HSOUT1 R1019 MOIREPLS 1k :CHIP C005 150p CH:CHIP R036 2.2k :RN-CP SOG R1013 2.2k :CHIP R1012 2.2k :CHIP R1010 1k :CHIP 125 VDD9 VSS GND ENV KEYDET MOIRECONT 124 UPWM6 D029 HZS5.1NB2TD C062 470 10V C055 47 25V C058 2200p CH:CHIP 127 VDD10 R1001 R1003 1k 1k R1002 R099 1k :CHIP :CHIP1k :CHIP :CHIP 132 VDD11 R1005 1k :CHIP 142 UPWM14 C044 0.022 B:CHIP OFFDET VSAWRST VSH HPLL AFCSW C061 0.01 B:CHIP VS1 HS/CS1 HS/CS2 VS2 R043 1k :CHIP C097 10 123 GND11 SDA VCC I HSOUT HFBP HFREQ HPHASE DVSHAPE VSHPLVL R1009 1k :CHIP R1011 1k :CHIP C098 0.01 B:CHIP MOIREPLS 122 UPWM5 bc3 bc2 bc1 5-26 5-25 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 8 7 6 S3 143 GND17 C052 100 16V J VCC+4.5V VDC MOIRE R1014 1k :CHIP C1006 2200p B:CHIP C054 0.1 B:CHIP GND 141 GND16 STBY+5V R1044 R1008 4.7k 4.7k :RN-CP :CHIP C056 22 160 VDD18 5 SDA SCL 159 GND21 4 TXD RXD 156 UPWM21 LCCLB LCCRB ab5 ab4 ab3 C059 C057 10 10 STBY+5V H 151 GND19 153 UPWM20 3 DSDA2 DSCL2 DSDA1 DSCL1 152 UPWM19 LCCLT LCCRT 2 INPUTSEL Q012 DTC124EKA INV. CBLK 150 GND18 149 UPWM18 G 145 HDCONT F 1 S4 S2 S1 S0 CLP HCONV LCCNS IC001 CXD8744Q CPU/DSP 140 UPWM13 ROTATION 144 UPWM15 HLINBAL 138 UPWM12 HCENT 133 UPWM10 HSP STBY+5V S6 S5 Q010 2SA1037AK INV. 131 UPWM9 VCONV 135 GND15 E 128 UPWM8 VDF 136 UPWM11 HSIZE 126 UPWM7 HSHPBAL 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 (µ-COM,GEO MAGNETIC SENSOR) STBY+5V 121 GND10 IC006 TL082CPS-E20 ABL DET AMP C AIN4 80 AVSS2 79 AIN3 78 AIN2 77 AIN1 76 AIN0 75 TEMP AVDD1 74 DAC1 73 AVSS1 72 DAC0 71 HDF0 GND4 70 P91 69 UOUT6 68 UOUT5 67 UOUT4 66 OSCVDD 65 XTO 64 XTB 63 OSCVSS 62 PA6 61 PA5 60 PA4 59 PA3 58 GND3 57 PA2 56 PA1 55 PA0 54 UOUT3 53 UOUT2 52 UOUT1 51 GND2 50 UBI4 49 UBI3 48 UBI2 47 UBI1 46 TXD 45 RXD 44 SCK2/P85 43 SDA2 42 SCL2 41 D ab2 ab1 B N -b A 14 13 12 11 10 9 8 7 6 5 4 3 2 1 B-SS9208<NH.>-N..-P2-EPS05 R5507 1.2 :FPRD R5508 1.2 :FPRD R5502 22k :CHIP R5506 6.8k :CHIP R5509 1.2 :FPRD R5503 22k :CHIP C5303 0.1 25V B:CHIP FB5303 1.1µH 7 6 R5319 10k :CHIP 8 5 R5119 10k :CHIP 6 6 C5310 47 25V C5206 0.01 B:CHIP C5404 0.01 B:CHIP R5322 22 1W :RS R5315 22 1W :RS R5122 22 1W :RS R5115 22 1W :RS R5206 22 1W :RS R5607 68 1W :RS R5415 150 2W :RS LCC-RT(+) LCC-RT(-) LCC-RB(+) LCC-RB(-) LCC-LT(+) LCC-LT(-) LCC-LB(+) LCC-LB(-) 1 2 3 4 5 6 7 8 LCC-NS(+) LCC-NS(-) B-SS9116<NH.>-N..-P3-EPS05 1 2 1 2 3 4 5 6 V CONV(+) V CONV(-) H CONV(+) H CONV(-) ROTATION+ ROTATION- LCC-LT LCC-LB LCC-RT LCC-RB LCC-NS V.CONV H.CONV ROTATION I R5510 1.2 :FPRD R5316 10k :CHIP C5308 0.1 25V B:CHIP 9 4 R5308 4.7 :CHIP 10 3 FB5301 1.1µH C5301 0.1 25V B:CHIP FB5103 1.1µH 7 R5313 10k :CHIP C5304 0.01 B:CHIP 2 C5306 0.1 25V B:CHIP C5103 0.1 25V B:CHIP C5108 0.1 25V B:CHIP R5108 4.7 :CHIP 5 8 4 9 3 R5113 10k :CHIP 6 R5208 R5205 6.8k 10k :CHIP :CHIP C5101 0.1 25V B:CHIP 7 FB5201 1.1µH 8 C5110 47 25V 2 R5109 4.7 :CHIP C5106 0.1 25V B:CHIP 9 FB5101 1.1µH 1 10 R5309 4.7 :CHIP 1 C5305 47 25V R5310 10k :CHIP R5116 10k :CHIP C5105 47 25V R5110 10k :CHIP C5205 0.1 25V B:CHIP C5203 0.1 25V B:CHIP R5209 4.7 :CHIP 5 10 4 R5605 100k :CHIP C5606 0.01 B:CHIP 3 FB5401 1.1µH 7 R5406 R5413 27k 100k :CHIP :CHIP C5607 0.1 25V B:CHIP R5603 15k :CHIP 2 C5602 0.1 B:CHIP FB5601 1.1µH 1 R5610 4.7 :CHIP R5602 22k :CHIP R5604 22k :CHIP R5410 22k :CHIP C5401 0.1 25V B:CHIP C5406 0.1 25V B:CHIP R5409 4.7 :CHIP 5 8 4 9 3 10 2 C5409 0.01 B:CHIP 1 R5407 33k :CHIP CN5002 8P YEL :S-MICRO -15V +15V LCCLB STBY+5V ac1 bc3 STBY+5V LCCLT LCCRB C5501 47 LCCRT LCCNS R5207 10k :CHIP R5504 47k :CHIP R5505 47k :CHIP R5408 4.7 :CHIP N -c C5413 0.1 25V B:CHIP 5-28 5-27 ROTATION HCONV VCONV FB5403 1.1µH (n)-c board , + + + + +15V R5416 22k :CHIP R5422 120 2W :RS < (n)-b board VEE VEE VEE VEE R5419 100k :CHIP Schematic diagram - C5403 0.01 B:CHIP Schematic diagram OUT2 + OUT2 + OUT2 + - C5408 470p B:CHIP H OUT2 + CN5003 2P WHT :S-MICRO V.S2 V.S2 V.S2 - CN5001 6P WHT :S-MICRO G VCC OUT1 VCC OUT1 VCC OUT1 V.S2 -15V V.S1 V.S1 V.S1 VCC OUT1 -15V IC5301 LA6515 AMP IC5101 LA6515 AMP +15V IC5201 LA6515 AMP IC5401 LA6515 AMP D V.S1 E bc2 bc1 C 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B F (H.V.CONV,LCC) (n) — N BOARD (Conductor Side) — 1 2 3 µ-COM, V.CONV, H.CONV, LCC, GEO MAGNETIC SENSOR • N BOARD SEMICONDUCTOR LOCATION — N BOARD (Component Side) — 1 2 IC Component ( Conductor Side ) ( Side ) IC001 IC002 IC003 IC004 IC005 IC006 IC010 IC011 IC012 IC5101 IC5201 IC5301 IC5401 A C-2 C-2 C-2 B-2 B-2 D-1 C-2 B-2 B-2 A-2 B-2 A-1 B-1 A A-2 B-2 A-2 B-2 TRANSISTOR Component ( Conductor Side ) ( Side ) Q001 Q002 Q003 Q004 Q005 Q006 Q007 Q008 Q010 Q011 Q012 B C-1 C-1 C-1 B-1 C-1 C-1 B-3 C-2 C-1 C-2 D-2 * 1 1 1 2 2 2 1 1 1 2 2 B DIODE Component ( Conductor Side ) ( Side ) D001 D002 D003 D004 D005 D006 D007 D008 D009 D010 D011 D012 D013 D014 D015 D016 D017 D018 D020 D021 D022 D023 D024 D025 D026 D027 D028 D029 D036 D038 C D A-1 A-1 C-3 B-2 A-2 A-2 C-3 C-3 C-3 A-2 C-3 C-2 B-2 B-2 B-1 B-1 B-1 C-3 C-3 B-2 B-2 B-1 B-2 D-2 D-2 D-3 D-3 C-1 B-1 A-1 A-1 C-1 C-1 C-1 A-1 C-1 C-2 B-2 B-2 B-2 B-1 D-1 D-1 C-1 * 7 7 6 7 – – – – – – – – – 8 8 – – – 3 3 8 8 8 6 6 3 3 – – 3 C D CRYSTAL Component ( Conductor Side ) ( Side ) X001 C-2 C-1 *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-10) 5-29 5-30 3 (5) Schematic Diagram of G Board 1 2 3 4 5 7 6 8 9 10 11 12 14 13 A G(POWER SUPPLY) CN604 1P IC650 DM-57N +220V SHUNT REG 5.7 GND 1 5 R653 470 2.5 4 3 180 2 B R649 47k :FPRD C661 2200p 1kV B C662 0.01 :PT T620 PIT CN654 8P WHT :S-MICRO 1 R652 470k :CHIP R650 2.2k :CHIP D650 D4SBL40 L650 22µH 5 9 8 7 12 11 L610 AFC R654 1 1/2W :RF C651 4.7 250V C650 100 250V 6 1 2 3 4 5 6 7 8 H CENT H H CENT N H CENT L TO D BOARD +220V CN508 +220V N.C GND GND 7 D610 D4SB60L D613 RM11A 0 GND 2.5 COMP 13.7 VCC 380 CATHODE R615 6.8k 3 4 D 5 6 7 8 9 10 C614 100p :CHIP Q621 2SC3311A REG SW 3 R611 0.47 2W R610 0.33 2W C610 330 450V R630 3.3 :FPRD C607 470p 250V B E1 C622 470p 1kV :HR D690 1SS119 4 181 R614 100 Q610 2SA1309A 15.9 VCC SW 379 R634 1M 1/2W 1 2 3 VDR601 0 D637 1SS119 1 C629 0.01 :PT 4.7 8 R693 68 1/2W AC L NC AC N H 1 2 3 DGC 3 5 2 14.7 15V 4 6 1 D692 1SS119 THP601 CN601 4P WHT :VH DGC NC NC DGC SG601 AC INLET C601 1 275V VDR602 Q691 2SC3311A RELAY DRIVE 0 1 2 3 1.5 R695 C634 4.7k 1000p :CHIP B:CHIP 2.5 0 2.1 3 C624 0.33 :MPS 2 D653 D2S4MTA1 C658 2200 10V D654 D2S4MTA1 C659 2200 10V 14.8 R636 R632 22k 120 3.2 :RN D634 1SS119 R617 1k 4 D666 1SS119 2 2 6 7 11.9 IN OUT GND 3 14.3 0.2 Q651 Q654 2SC2458 R659 1k POWER SW :CHIP 2SA1037AK SW 11.4 D665 D663 1SS1191SS119 11.4 R661 100 Q652 2SC2412K 0.1 PROTECT 0.2 Q650 2SA1309A POWER SW D683 1SS119 0.7 R662 10k :CHIP C663 22 3 2 4 1 R683 C687 10 2.2k :CHIP 6.8 Q670 R684 10k 1.2 2SA1037AK PROTECT R685 6.8 1k :CHIP IN OUT GND 6.8 :CHIP D680 YG802C09 3 Q667 2SA1037AK PROTECT R688 150k :RN D664 RD22ESB2 4.0 R681 4.0 10k :CHIP R682 1k R666 :CHIP 10k :CHIP R668 33k :RN 4.0 0 R667 47k :CHIP C665 47 10V 993 Q630 2SK2647-01MR REG SW L680 22µH 0 C680 6800 10V R618 1 2W :RS C682 R670 R671 4700p 12k 12k :PT :RN-CP:RN-CP 3 2 C633 2200p B:CHIP PH630 ON3171-R C630 470p B:CHIP 3 2.5 1 2 R686 220 6.7 :CHIP R687 22k :CHIP R678 1.5 3W :RS C681 47 10V IC651 BA00AST-V5 HEATER REG 1 2.4 R616 6.8k :RN-CP IC652 BA05ST-V5 STBY+5V REG 5.6 IC680 HA17431PA-TZ RECT R672 3.6k :RN-CP 1 2 R673 10k :CHIP 3 4 5 1 2 3 C683 47 10V 4 C685 R675 100 5.1k 10V :RN-CP 3.5 R674 100k :CHIP 5 R676 3.3k :RN-CP C684 100 10V R677 2.7k :RN-CP 4.7 CN650 7P WHT :S-MICRO 1.2 Q671 2SA1037AK HEATER SW 1 2 3 4 5 6 7 D681 RD5.6ESB2 5.6 1 2 3 4 I B-SS9208<NH.>-G..-EPS05 Schematic diagram (g) board , 5-31 TO A BOARD CN405 R663 10k :CHIP C686 47 10V 2 IC653 BA05T 1W+5V REG STBY+5V 1W+5V GND +80V N.C +220V N.C +12V HEATER Q653 2SC2412K PROTECT 5.0 1 6.1 TO D BOARD CN501 R680 180k :RN R664 R665 10k 2.2k :CHIP :CHIP 0.1 6 5 R658 10k :CHIP 14.3 3 3 5 5 C667 47 16V D660 RD22ESB2 R660 10k :CHIP 1 2 3 4 5 6 7 8 9 IC654 µPC2912HF +12V REG D661 RD12ESB2 R655 4.7k :CHIP C666 10 7 8 +12V +15V GND -15V GND +80V CN652 9P WHT :S-MICRO R656 1 1/2W :FPRD D656 1SS119 11.2 C625 0.15 :MPS 0.3 4.9 R609 6.8k R608 :CHIP 10k :CHIP C657 R638 47 0.1 25V :RF L653 22µH T621 PRT 1 1 8 4 R694 C692 0.1 10k :CHIP B:CHIP C660 47 PH620 ON3171-R S 5 IC630 FA13842P REG RY603 F601 6.3A 6 16.1 T601 :LFT CN602 3P WHT :VH 7 4 2 R626 1 1W :RS 4 0 4.9 C602 1 275V C656 2200 25V 4 4 3 G 12 2 C631 100 25V R607 100k :CHIP 1 1 C626 0.15 :MPS T630 SRT D633 ERB38-06V1 D631 D1NL20U D635 RD20ESB2 R601 330k 1/2W :SURGE 351 C627 470p 1kV :HR R613 47k :CHIP FB630 0.45µH 1.4 R604 470k :CHIP 11 R623 100k 1W :RS D620 1SS119 1 R606 100k :CHIP 2 C655 47 25V R657 D632 P6KE200AG23 189 R605 470k :CHIP 0.5 C604 470p 250V B C603 470p 250V B TO J BOARD CN891 0 Q633 2SC2412K VCC SW FB632 1.1µH 16.1 R602 27k 2W :RS Q632 2SC4015 VCC SW B2 D612 15.2 R612 10k 1SS119 2SC4015 VCC SW 188 CN603 3P L652 22µH C654 2200 25V R624 100k 1W :RS R625 1 1W :RS C623 0.33 :MPS R628 68k :CHIP R621 18k R629 22k :CHIP R603 470k AC L OUT NC AC L IN -1.1 348 R622 47k :CHIP 1 R635 27k 2W Q631 :RS E2 R627 22k :CHIP R696 150 1/4W R633 1M 1/2W F B1 R637 0.1 :RF D655 0.47 D1NL20U :FPRD C612 C613 0.22 47 :MPS 2 TH601 E CN653 6P WHT :S-MICRO 1 2 3 4 5 6 10 C2 -1.1 -1.0 C611 1 400V 9 D652 D4SBS4 380 C1 C653 4.7 100V 4.8 CTL 5.5 Vcc GND 5.0 OUT VADJ 1.2 2 4 3 348 Q603 MX0842AB-F REG OUT START UP JW604 1 C620 0.027 800V :PP C621 470p 1kV :HR PS650 2.0A JW605 DRAIN 240 GATE 90.6 AC SEN 0.1 SOURCE 2.4 L SEN C605 4700p 250V R620 0.1 1/2W :RF C652 100 100V 2.8 CTL 6.8 Vcc GND 5.0 OUT NC IC610 MZ1530 PFI L611 68µH RY602 15V 8 D682 RD9.1ESB C606 4700p 250V L651 22µH D651 D1NL20U 1 2 3 4 5 6 C 5-32 STBY+5V 1W+5V ECO SW PWR SW DGUS SW HTR SW GND TO D BOARD CN502 (g) POWER SUPPLY — G BOARD — 1 2 3 4 • G BOARD SEMICONDUCTOR LOCATION 5 IC IC610 IC630 IC650 IC651 IC652 IC653 IC654 IC680 A A-4 C-3 A-1 C-1 C-1 C-1 B-1 C-2 TRANSISTOR Q603 Q610 Q621 Q630 Q631 Q632 Q633 Q650 Q651 Q652 Q653 Q654 Q667 Q670 Q671 Q691 B A-3 C-2 C-3 C-3 B-3 C-3 C-3 B-2 B-1 C-1 B-1 B-2 C-1 C-2 C-1 C-2 *– – – – – – 1 – – 1 1 1 1 1 1 – DIODE D610 D612 D613 D620 D631 D632 D633 D634 D635 D637 D650 D651 D652 D653 D654 D655 D656 D660 D661 D663 D664 D665 D666 D680 D681 D682 D683 D690 D692 C NOTE: The circuit indicated as left contains high voltage of over 600 Vp-p. Care must be paid to prevent an electric shock in inspection or repairing. B-4 C-2 A-4 C-2 C-2 B-3 B-3 C-3 C-3 C-3 A-2 B-2 A-1 A-2 A-1 B-2 B-2 B-1 C-2 C-1 B-1 B-1 C-2 B-2 C-1 C-1 C-2 C-3 C-4 *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 5-10) 5-33 5-34 5-5. SEMICONDUCTORS BA00AST-V5 BA05ST-V5 LA6500-FA BA9759F-E2 n 1 M52749FP-TP HA17431PA HA17431PA-TZ n 1 TOP VIEW TOP VIEW 42pin SOP 18pin SOP DTA124ESA DTA124ESA-TP 2SA1175-HFE 2SA1309A-QRSTA 2SC2459-GR-TPE4 2SC2784 2SC2785-HFE 2SC3311A-QRSTA 2SC2362K-G 2SC2362KG-AA 2SJ360-TE12L G D S LETTER SIDE E C B ERA22-06AVRBT ERA22-08 ERA34-10TP1 ERB38-06V1 GP08D GP08DPKG23 HSS83TD P6KE200AG23 RD2.2M-T1B RGP02-20EL-6394 ON3171-R 1PS181-115 RD9.1ES-L2 RD9.1ES-T1B 1PS226-115 CATHODE 1 5 M52757FP-TP CXD8744Q 2SC3209LK 2SC3209LK-TP H8D2972 n BA05T E C B n 1 1 1 3 TOP VIEW 8 10 160pin QFP G 17 µPC2912HF (12) CXD9514M 2SC4015TV2 n TOP VIEW n 12 LA7841L MARKING SIDE VIEW MARKING SIDE VIEW 14pin SOP NJM082M NJM2904M NJM2904M(TE2) TL082CPS-E20 24LC21AT/SN 1 1 5pin SIP 7pin SIP FA13842P M24C16-MN6T MM1170BFB n LA7865M-TLM 36 19 n 1 TOP VIEW 1 TOP VIEW 1 8pin SOP 2SA1049-GR 2SA1049TP-GR 2SC2458-YGR 2SC2458TP-YGR 10pin SIP DM-57N TOP VIEW 3 DTA114GKAT146 DTA114TUA-T106 DTA124EUA-T106 DTA143TKA-T146 DTC114GKA DTC114GKAT146 DTC123EKA-T146 DTC124EK DTC124EKA-T146 2SA1036K-Q 2SA1036K-T-146-Q 2SA1037AK-T146-QR 2SA1037AK-T146-R 2SA1037K-T146-QR 2SA1162-G 2SB709A-QRS-TX 2SC1623-L5L6 2SC2411K-CQ 2SC2411K-T-146-CQ 2SC2412K-T-146-QR E MZ1530 E FA4301 C 1 10 ANODE ANODE ~ 2SA1358-Y 2SC3421-Y ~ – C E + ~ 2SD2394-EF ~ – D5SC4M 1PS184-115 B 2SB1565EF 2SC3746 2SC4634LS-CB11 2SC5022-02 G S B D 2SJ569LS-CB11 2SK2655-01R-F165 2SK3262-01MR-F119 EGP10D EGP10GPKG23 ERA91-02 ERA91-02TP1 C E D CATHODE S HZS10NB2TD HZS12NB2TD HZS13NB2TD HZS16NB2TD HZS33NB2 HZS33NB2TD HZS4.7NB2 HZS4.7NB2TD HZS5.1NB2TD HZS5.6NB2TD MTZJ-T-77-39B MTZJ-39B RD10ESB2 RD12ES-B2 RD12ES-T1B2 RD13ES-B2 RD20ES-B2 RD20ES-T1B2 RD22ES-B2 RD22ES-T1B2 RD5.1ESB2 RD5.6ES-T1B2 RD5.6ESB2 UDZ-TE-17-2.2B 1SS119-25 1SS119-25TD 1SS133T-77 ANODE CATHODE ANODE (GRN) ANODE (RED) CATHODE YG802C09 YG911S3R CATHODE CATHODE G 5-35 1SS376TE-17 SPR-325MVW D4SB60L D4SBL40 D4SBS4 D4SBS4-F B 1 15pin SIP ANODE CATHODE TOP VIEW 20pin SOP CATHODE HSU83TRF B B MARKING SIDE VIEW 1 C + EC B E 2SC5570(LBSONY) 18 C n 1SS355TE-17 RM11A RM11C ANODE 8pin DIP BA9758FS-E2 S CATHODE 1 28pin SOP D D1NL20U-TR D2S4MF D2S4MTA1 MARKING SIDE VIEW 1 1 FMQ-G5GS E C B LA6515 BA10324AF-E2 SN74AHCT74PWR SN74HC04ANS SN74HC04ANSR XRA10324AF ANODE MX0842AB-F TOP VIEW 36pin SOP 1 2 3 2SK2647-01MR-F91 ANODE 5-36 ANODE GDM-5403 SECTION 6 EXPLODED VIEWS • Items with no part number and no description are not stocked because they are seldom required for routine service. • The construction parts of an assembled part are indicated with a collation number in the remark column. • Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The components identified 0 marked are critical for safety. Replace only with the part number specified. 6-1. CHASSIS z x 7-685-648-79 7-685-646-79 7-685-881-09 f +BVTP 3X12 +BVTP 3X8 +BVTT 4X8 16 15 5 19 20 17 14 2 12 3 4 13 18 11 1 9 7 5 8 6 REF.NO. PART NO. 1 2 DESCRIPTION REMARK REF.NO. PART NO. 3 4 5 * A-1346-859-B D BOARD, COMPLETE 2 0 X-4560-175-1 TRANSFORMER ASSY, FLYBACK (NX-4502/J1D4) 4-062-115-01 SCREW +P 3.5X20 TYPE2 4-389-025-11 SCREW (M4) (EXT TOOTH WASHER) * 3-701-903-11 HOLDER, PRINTED CIRCUIT BOARD 6 7 8 9 11 4-070-730-01 HOLDER, PRINTED CIRCUIT BOARD * A-1316-480-A G BOARD, COMPLETE 0 1-251-382-31 INLET, AC 3P (WITH NOISE FILTER) 4-205-206-01 SCREW (HD15) * A-1298-988-B A BOARD, COMPLETE 6-1 DESCRIPTION REMARK 12 13 14 15 16 1-900-246-08 1-900-250-06 * 4-069-570-01 4-073-300-11 * 4-204-328-21 CONNECTOR ASSY (F) CONNECTOR ASSY (F) SPACER, PRINTED CIRCUIT BOARD CABINET COVER, ECS 17 17 17 18 19 20 * 4-205-299-01 * 4-205-354-01 * 4-205-369-01 4-039-358-01 * 4-063-711-01 * 4-060-359-01 LABEL, INFORMATION [OEM STD] LABEL, INFORMATION [FORMAC] LABEL, INFORMATION [ELSA] SCREW (4X16) (+) BV TAPPING SUPPORT, HV CABLE HOLDER, PRINTED CIRCUIT BOARD GDM-5403 6-2. PICTURE TUBE x f 7-685-663-71 7-685-881-09 +BVTP 4X16 +BVTT 4X8 70 71 69 80 67 81 82 74 83 72 63 75 68 62 61 56 65 64 66 73 60 76 55 52 54 77 58 53 59 The components identified 0 marked are critical for safety. Replace only with the part number specified. 51 REF.NO. PART NO. 51 51 51 52 53 54 55 56 58 58 X-4200-581-1 X-4200-585-1 X-4200-587-1 4-073-296-01 4-042-593-01 DESCRIPTION REMARK BEZEL ASSY [OEM STD] BEZEL ASSY [FORMAC] BEZEL ASSY [ELSA] BUTTON, POWER SPRING, COMPRESSION REF.NO. PART NO. 0 1-419-128-21 0 1-419-129-21 4-062-670-01 4-203-648-01 4-070-730-01 DESCRIPTION 52-56 52-56 52-56 66 67 68 69 70 4-073-295-01 BAR, OPTICAL 4-073-301-01 BUTTON, MULTI 4-073-298-01 BUTTON, RESET * A-1372-740-A H BOARD, COMPLETE [ELSA, FORMAC] * A-1646-207-A H BOARD, COMPLETE [OEM STD] 71 72 73 74 75 * A-1394-967-B N BOARD, COMPLETE * A-1388-260-B J BOARD, COMPLETE X-4037-324-1 STAND ASSY 4-204-326-01 STOPPER (A) * 4-204-376-01 RING, TILT SWIVEL 76 77 80 81 82 * 4-061-996-11 4-072-648-01 4-308-870-00 1-452-032-00 1-452-094-00 59 60 61 62 63 4-029-432-01 0 8-738-813-61 0 8-451-509-11 0 1-452-912-61 2-162-100-21 SCREW (3X12), (+) BVWHTP ITC ASSY (21TKC-R1) 61-63 DEFLECTION YOKE (Y21TKM-M) NECK ASSENBLY (NA-2914) SPACER, DEFLECTION YOKE 64 65 * 4-047-316-01 SPRING, EXTENSION 0 1-419-130-21 COIL, LANDING CORRECTION 83 6-2 REMARK COIL, DEGAUSSING COIL, LANDING CORRECTION SPACER, PICTURE TUBE SCREW (5), SELF TAPPING HOLDER, PRINTED CIRCUIT BOARD 74-77 CUSHION STOPPER (B) CLIP, LEAD WIRE MAGNET, DISK: 10mmφ MAGNET, ROTATABLE DISK: 15mmφ 4-051-736-21 PIECE A (90), CONV. CORRECT GDM-5403 6-3. PACKING MATERIALS 105 106 107 101 102 104 103 The components identified 0 marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. DESCRIPTION 101 102 103 104 104 * 4-073-356-01 * 4-368-079-01 * 4-073-357-01 * 4-205-298-01 * 4-205-355-01 104 * 4-205-367-01 INDIVIDUAL CARTON [ELSA] REMARK REF.NO. PART NO. CUSHION (UPPER) (ASSY) BAG, POLYETHYLENE CUSHION (LOWER) (ASSY) INDIVIDUAL CARTON [OEM STD] INDIVIDUAL CARTON [FORMAC] 105 106 106 106 107 6-3 DESCRIPTION REMARK 1-793-504-11 CABLE ASSY (15P D SUB X 2 CONNECTOR) 3-868-394-11 MANUAL, INSTRUCTION [ELSA] 4-075-849-11 MANUAL, INSTRUCTION [OEM STD] 4-075-849-31 MANUAL, INSTRUCTION [FORMAC] 0 1-782-784-21 CORD SET, POWER The components identified ¡ marked are critical for safety. Replace only with the part number specified. GDM-5403 SECTION 7 (a) ELECTRICAL PARTS LIST REF.NO. PART NO. NOTE: DESCRIPTION The components identified ¡ marked are critical for safety. Replace only with the part number specified. When indicating parts by reference number, please include the board name. REF.NO. PART NO. REMARK identified REF.NO.by PART DESCRIPTION REMARK The components [ in NO. this • Items marked " * " are not stocked since manual have been carefully factory- they are seldom required for routine selected for each set in order to satisfy service. Some delay should be anticipated regulations regarding X-ray radiation. when ordering these items. Should replacement be required, replace only with the value originally used. RESISTORS • All resistors are in ohms • All variable and adjustable resistors have • F : nonflammable characteristic curve B, unless otherwise noted. DESCRIPTION REMARK REF.NO. PART NO. * A-1298-988-BA BOARD, COMPLETE *************************** 7-682-950-01 SCREW +PSW 3X12 (IC403) <CAPACITOR> C101 C102 C103 C104 C107 1-163-021-91 1-104-664-11 1-163-021-91 1-104-664-11 1-164-004-11 CERAMIC CHIP 0.01µF ELECT 47µF CERAMIC CHIP 0.01µF ELECT 47µF CERAMIC CHIP 0.1µF 10% 20% 10% 20% 10% 50V 25V 50V 25V 25V C108 C109 C110 C112 C113 1-164-004-11 1-163-229-11 1-163-275-11 1-164-489-11 1-164-489-11 CERAMIC CHIP 0.1µF CERAMIC CHIP 12pF CERAMIC CHIP 0.001µF CERAMIC CHIP 0.22µF CERAMIC CHIP 0.22µF 10% 5% 5% 10% 10% 25V 50V 50V 16V 16V C114 C115 C120 C201 C202 1-164-004-11 1-104-341-11 1-104-341-11 1-163-021-91 1-104-664-11 CERAMIC CHIP 0.1µF FILM 0.1µF FILM 0.1µF CERAMIC CHIP 0.01µF ELECT 47µF 10% 10% 10% 10% 20% 25V 250V 250V 50V 25V C203 C204 C205 C206 C207 1-163-021-91 1-104-664-11 1-163-021-91 1-109-982-11 1-164-004-11 CERAMIC CHIP 0.01µF ELECT 47µF CERAMIC CHIP 0.01µF CERAMIC CHIP 1µF CERAMIC CHIP 0.1µF 10% 20% 10% 10% 10% 50V 25V 50V 10V 25V C208 C209 C210 C212 C213 1-164-004-11 1-163-227-11 1-163-275-11 1-164-489-11 1-164-489-11 CERAMIC CHIP 0.1µF CERAMIC CHIP 10pF CERAMIC CHIP 0.001µF CERAMIC CHIP 0.22µF CERAMIC CHIP 0.22µF 10% 0.5pF 5% 10% 10% 25V 50V 50V 16V 16V C214 C215 C216 C220 C301 1-164-004-11 1-104-341-11 1-163-021-91 1-104-341-11 1-163-021-91 CERAMIC CHIP 0.1µF FILM 0.1µF CERAMIC CHIP 0.01µF FILM 0.1µF CERAMIC CHIP 0.01µF 10% 10% 10% 10% 10% 25V 250V 50V 250V 50V C302 C303 C304 C307 C308 1-104-664-11 1-163-021-91 1-104-664-11 1-164-004-11 1-164-004-11 ELECT 47µF CERAMIC CHIP 0.01µF ELECT 47µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF 20% 10% 20% 10% 10% 25V 50V 25V 25V 25V C309 1-163-227-11 CERAMIC CHIP 10pF 0.5pF 50V 7-1 DESCRIPTION REMARK C310 C312 C313 C314 1-163-275-11 CERAMIC CHIP 0.001µF 1-164-489-11 CERAMIC CHIP 0.22µF 1-164-489-11 CERAMIC CHIP 0.22µF 1-164-004-11 CERAMIC CHIP 0.1µF 5% 10% 10% 10% 50V 16V 16V 25V C315 C320 C401 C402 C403 1-104-341-11 FILM 0.1µF 1-104-341-11 FILM 0.1µF 1-126-964-11 ELECT 10µF 1-104-664-11 ELECT 47µF 1-163-259-91 CERAMIC CHIP 220pF 10% 10% 20% 20% 5% 250V 250V 50V 25V 50V C404 C405 C406 C407 C408 1-163-259-91 CERAMIC CHIP 220pF 1-164-004-11 CERAMIC CHIP 0.1µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 5% 10% 10% 10% 10% 50V 25V 50V 50V 50V C410 C411 C413 C415 C416 1-163-021-91 CERAMIC CHIP 0.01µF 1-126-934-11 ELECT 220µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-164-489-11 CERAMIC CHIP 0.22µF 1-126-961-11 ELECT 2.2µF 10% 20% 10% 10% 20% 50V 16V 50V 16V 50V C417 C419 C420 C421 C422 1-104-574-11 CERAMIC 0.0047µF 1-162-318-11 CERAMIC 0.001µF 1-164-489-11 CERAMIC CHIP 0.22µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-164-489-11 CERAMIC CHIP 0.22µF 10% 10% 10% 10% 10% 2KV 500V 16V 50V 16V C423 C424 C425 C426 C427 1-104-664-11 ELECT 47µF 1-162-318-11 CERAMIC 0.001µF 1-163-251-11 CERAMIC CHIP 100pF 1-163-251-11 CERAMIC CHIP 100pF 1-163-235-11 CERAMIC CHIP 22pF 20% 10% 5% 5% 5% 25V 500V 50V 50V 50V C430 C431 C432 C433 C434 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-275-11 CERAMIC CHIP 0.001µF 1-164-489-11 CERAMIC CHIP 0.22µF 1-162-318-11 CERAMIC 0.001µF 1-162-318-11 CERAMIC 0.001µF 10% 5% 10% 10% 10% 50V 50V 16V 500V 500V C435 C436 C437 C438 C440 1-163-021-91 CERAMIC CHIP 0.01µF 1-164-489-11 CERAMIC CHIP 0.22µF 1-126-935-11 ELECT 470µF 1-115-339-11 CERAMIC CHIP 0.1µF 1-163-021-91 CERAMIC CHIP 0.01µF 10% 10% 20% 10% 10% 50V 16V 16V 50V 50V C441 C442 C443 C444 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-162-318-11 CERAMIC 0.001µF 10% 10% 10% 10% 50V 50V 50V 500V GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. (a) REF.NO. PART NO. DESCRIPTION REMARK C446 1-104-664-11 ELECT 47µF C449 C450 C456 C457 C458 1-109-982-11 CERAMIC CHIP 1µF 1-107-823-11 CERAMIC CHIP 0.47µF 1-164-489-11 CERAMIC CHIP 0.22µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-115-339-11 CERAMIC CHIP 0.1µF 10% 10% 10% 10% 10% 10V 16V 16V 50V 50V C459 C462 C463 C464 C467 1-128-560-11 ELECT 22µF 1-115-339-11 CERAMIC CHIP 0.1µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-107-957-11 ELECT 1µF 20% 10% 10% 10% 20% 100V 50V 50V 50V 250V REF.NO. PART NO. DESCRIPTION FB411 1-412-911-11 FERRITE 20% 25V REMARK 1.1µH <IC> IC401 IC402 IC403 IC404 IC405 8-759-584-87 8-759-584-86 8-749-015-91 8-759-585-72 8-759-701-01 IC M52757FP-TP IC M52749FP-TP IC FA4301 IC CXD9514M IC NJM2904M IC406 8-749-015-92 IC H8D2972 IC407 8-759-925-74 IC SN74HC04ANS <COIL> <CONNECTOR> L402 L403 L404 L405 CN401 1-793-183-11 CONNECTOR, D SUB 15P CN402*1-564-509-11 PLUG, CONNECTOR 6P CN403 1-784-463-11 CONNECTOR, FFC/FPC 21P CN405*1-564-524-11 PLUG, CONNECTOR 9P CN406*1-766-179-11 PIN, CONNECTOR (PC BOARD) 2P 1-412-529-11 1-412-537-31 1-414-940-21 1-412-529-11 INDUCTOR INDUCTOR INDUCTOR INDUCTOR 22µH 100µH 100µH 22µH <IC LINK> PS401¡ 1-533-590-31 LINK, IC (1A/90V AC, 60V DC) <DIODE> D101 D102 D103 D105 D106 8-719-062-51 DIODE 1PS226-115 8-719-062-51 DIODE 1PS226-115 8-719-066-10 DIODE 1PS181-115 8-719-051-85 DIODE HSS83TD 8-719-052-12 DIODE 1SS376TE-17 D107 D201 D202 D203 D205 8-719-052-12 DIODE 1SS376TE-17 8-719-062-51 DIODE 1PS226-115 8-719-062-51 DIODE 1PS226-115 8-719-066-10 DIODE 1PS181-115 8-719-051-85 DIODE HSS83TD D206 D207 D301 D302 D303 8-719-052-12 DIODE 1SS376TE-17 8-719-052-12 DIODE 1SS376TE-17 8-719-062-51 DIODE 1PS226-115 8-719-062-51 DIODE 1PS226-115 8-719-066-10 DIODE 1PS181-115 D305 D306 D307 D402 D403 8-719-051-85 DIODE HSS83TD 8-719-052-12 DIODE 1SS376TE-17 8-719-052-12 DIODE 1SS376TE-17 8-719-066-11 DIODE 1PS184-115 8-719-982-36 ZENER DIODE MTZJ-39B D405 D406 D407 8-719-911-19 DIODE 1SS119-25 8-719-062-51 DIODE 1PS226-115 8-719-062-51 DIODE 1PS226-115 <TRANSISTOR> 1-500-419-22 FERRITE 1-500-419-22 FERRITE 1-500-419-22 FERRITE 1-412-911-11 FERRITE 1-412-911-11 FERRITE 1.1µH 1.1µH FB404 1-412-911-11 FERRITE FB405 1-412-911-11 FERRITE FB406 1-412-911-11 FERRITE 1.1µH 1.1µH 1.1µH 8-729-120-28 8-729-120-28 8-729-120-28 8-729-120-28 8-729-050-41 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SJ360TE12L Q406 Q407 Q410 8-729-216-22 TRANSISTOR 2SA1162-G 8-729-028-74 TRANSISTOR DTA114TUA-T106 8-729-032-61 TRANSISTOR 2SC5022-02 <RESISTOR> <FERRITE BEAD> FB102 FB202 FB302 FB402 FB403 Q101 Q201 Q301 Q401 Q402 7-2 R101 R103 R105 R106 R107 1-215-394-00 1-215-394-00 1-216-017-91 1-216-017-91 1-216-045-00 METAL METAL RES-CHIP RES-CHIP RES-CHIP 75 75 47 47 680 1% 1% 5% 5% 5% 1/4W 1/4W 1/10W 1/10W 1/10W R109 R110 R111 R112 R113 1-216-678-11 1-216-097-91 1-216-041-00 1-216-009-91 1-216-017-91 METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 13K 100K 470 22 47 0.5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R114 R115 R116 R117 R118 1-216-009-91 1-219-742-11 1-216-065-91 1-216-121-91 1-216-121-91 RES-CHIP CARBON RES-CHIP RES-CHIP RES-CHIP 22 47 4.7K 1M 1M 5% 5% 5% 5% 5% 1/10W 1/2W 1/10W 1/10W 1/10W R119 R120 R121 R122 R128 1-216-077-91 1-216-113-00 1-216-113-00 1-216-081-00 1-216-065-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 15K 470K 470K 22K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R130 1-216-113-00 RES-CHIP 470K 5% 1/10W GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. (a) DESCRIPTION REMARK R137 R138 R161 R201 1-249-413-11 1-216-017-91 1-216-041-00 1-215-394-00 CARBON RES-CHIP RES-CHIP METAL 470 47 470 75 5% 5% 5% 1% 1/4W 1/10W 1/10W 1/4W R202 R203 R205 R206 R207 1-216-097-91 1-215-394-00 1-216-017-91 1-216-017-91 1-216-045-00 RES-CHIP METAL RES-CHIP RES-CHIP RES-CHIP 100K 75 47 47 680 5% 1% 5% 5% 5% 1/10W 1/4W 1/10W 1/10W 1/10W R209 R210 R211 R212 R213 1-216-678-11 1-216-097-91 1-216-033-00 1-216-009-91 1-216-017-91 METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 13K 100K 220 22 47 0.5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R214 R215 R216 R217 R218 1-216-009-91 1-219-742-11 1-216-065-91 1-216-121-91 1-216-121-91 RES-CHIP CARBON RES-CHIP RES-CHIP RES-CHIP 22 47 4.7K 1M 1M 5% 5% 5% 5% 5% 1/10W 1/2W 1/10W 1/10W 1/10W R219 R220 R221 R222 R228 1-216-077-91 1-216-113-00 1-216-113-00 1-216-081-00 1-216-065-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 15K 470K 470K 22K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R230 R237 R238 R261 R301 1-216-113-00 1-249-413-11 1-216-017-91 1-216-041-00 1-215-394-00 RES-CHIP CARBON RES-CHIP RES-CHIP METAL 470K 470 47 470 75 5% 5% 5% 5% 1% 1/10W 1/4W 1/10W 1/10W 1/4W R303 R305 R306 R307 R309 1-215-394-00 1-216-017-91 1-216-017-91 1-216-045-00 1-216-678-11 METAL RES-CHIP RES-CHIP RES-CHIP METAL CHIP 75 47 47 680 13K 1% 5% 5% 5% 0.5% 1/4W 1/10W 1/10W 1/10W 1/10W R310 R311 R312 R313 R314 1-216-097-91 1-216-033-00 1-216-009-91 1-216-017-91 1-216-009-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100K 220 22 47 22 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R315 R316 R317 R318 R319 1-219-742-11 1-216-065-91 1-216-121-91 1-216-121-91 1-216-077-91 CARBON RES-CHIP RES-CHIP RES-CHIP RES-CHIP 47 4.7K 1M 1M 15K 5% 5% 5% 5% 5% 1/2W 1/10W 1/10W 1/10W 1/10W R320 R321 R322 R328 R330 1-216-113-00 1-216-113-00 1-216-081-00 1-216-065-91 1-216-113-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 470K 470K 22K 4.7K 470K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R337 R338 R361 R402 R403 1-249-413-11 1-216-017-91 1-216-041-00 1-216-049-91 1-216-081-00 CARBON RES-CHIP RES-CHIP RES-CHIP RES-CHIP 470 47 470 1K 22K 5% 5% 5% 5% 5% 1/4W 1/10W 1/10W 1/10W 1/10W R404 R405 1-216-057-00 RES-CHIP 1-216-045-00 RES-CHIP 2.2K 680 5% 5% 1/10W 1/10W REF.NO. PART NO. DESCRIPTION R406 R407 R409 1-216-097-91 RES-CHIP 1-218-768-11 METAL CHIP 1-216-129-00 RES-CHIP 100K 470K 2.2M 5% 1/10W 0.5% 1/10W 5% 1/10W R411 R412 R413 R414 R415 1-216-065-91 RES-CHIP 1-216-105-91 RES-CHIP 1-216-097-91 RES-CHIP 1-216-089-91 RES-CHIP 1-216-097-91 RES-CHIP 4.7K 220K 100K 47K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R417 R418 R419 R420 R421 1-216-121-91 RES-CHIP 1-260-127-11 CARBON 1-216-033-00 RES-CHIP 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1M 220K 220 100 100 5% 5% 5% 5% 5% 1/10W 1/2W 1/10W 1/10W 1/10W R422 R424 R425 R426 R427 1-216-025-91 RES-CHIP 1-216-049-91 RES-CHIP 1-216-049-91 RES-CHIP 1-216-105-91 RES-CHIP 1-216-049-91 RES-CHIP 100 1K 1K 220K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R428 R430 R431 R436 R438 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-113-00 RES-CHIP 1-216-057-00 RES-CHIP 1-216-065-91 RES-CHIP 100 100 470K 2.2K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R439 R441 R442 R443 R444 1-216-041-00 RES-CHIP 1-216-121-91 RES-CHIP 1-216-049-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 470 1M 1K 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R445 R446 R447 R448 R449 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-017-91 RES-CHIP 1-216-017-91 RES-CHIP 1-216-081-00 RES-CHIP 100 100 47 47 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R450 R451 R453 R454 R455 1-216-065-91 RES-CHIP 1-216-115-00 RES-CHIP 1-216-073-00 RES-CHIP 1-216-129-00 RES-CHIP 1-216-097-91 RES-CHIP 4.7K 560K 10K 2.2M 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R456 R457 R458 R459 R460 1-216-025-91 RES-CHIP 1-211-895-11 METAL 1-219-398-51 METAL 1-211-895-11 METAL 1-216-073-00 RES-CHIP 100 10M 2.2M 10M 10K 5% 10% 5% 10% 5% 1/10W 1/4W 1W 1/4W 1/10W R461 R463 R464 R488 R490 1-216-105-91 RES-CHIP 1-216-097-91 RES-CHIP 1-216-057-00 RES-CHIP 1-216-089-91 RES-CHIP 1-216-065-91 RES-CHIP 220K 100K 2.2K 47K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R491 1-216-065-91 RES-CHIP 4.7K 5% 1/10W <SPARK GAP> SG101 1-576-354-21 GAP, SPARK SG201 1-576-354-21 GAP, SPARK SG301 1-576-354-21 GAP, SPARK 7-3 REMARK GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. (a)(g) REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. SG401 1-576-354-21 GAP, SPARK SG402 1-519-422-11 GAP, SPARK <SOCKET> SK401 ¡ 1-451-499-11 SOCKET, PICTURE TUBE DESCRIPTION REMARK C657 C658 C659 1-104-664-11 ELECT 1-126-927-11 ELECT 1-128-339-11 ELECT 47µF 2200µF 2200µF 20% 25V 20% 10V 20% 10V C660 C661 C662 C663 C665 1-126-967-11 1-107-429-11 1-137-370-11 1-126-965-11 1-107-909-11 ELECT CERAMIC FILM ELECT ELECT 47µF 0.0022µF 0.01µF 22µF 47µF 20% 10% 5% 20% 20% 50V 1KV 50V 50V 10V C666 C667 C680 C681 C682 1-126-964-11 1-107-909-11 1-115-747-51 1-104-664-11 1-137-368-11 ELECT ELECT ELECT ELECT FILM 10µF 47µF 0.0068F 47µF 0.0047µF 20% 20% 20% 20% 5% 50V 16V 10V 10V 50V C683 C684 C685 C686 C687 1-104-664-11 1-128-526-11 1-128-526-11 1-104-664-11 1-126-964-11 ELECT ELECT ELECT ELECT ELECT 47µF 100µF 100µF 47µF 10µF 20% 20% 20% 20% 20% 10V 10V 10V 10V 50V C692 1-115-339-11 CERAMIC CHIP 0.1µF <CRYSTAL> X401 1-781-472-21 VIBRATOR, CERAMIC (8MHz) ******************************************************************************* * A-1316-480-A G BOARD, COMPLETE **************************** 1-533-223-11 HOLDER, FUSE (F601) 4-382-854-11 SCREW (M3X10), P, SW (+) (D610, D652, D680, IC610, IC654, Q603, Q630) 10% 50V <CONNECTOR> <CAPACITOR> C601 ¡ 1-113-513-11 C602 ¡ 1-113-513-11 C603 ¡ 1-113-900-51 C604 ¡ 1-113-900-51 C605 ¡ 1-113-926-91 FILM FILM CERAMIC CERAMIC CERAMIC 1µF 1µF 470pF 470pF 0.0047µF C606 ¡ 1-113-926-91 C607 1-113-900-11 C610 1-117-849-11 C611 1-137-479-11 C612 1-136-169-00 CERAMIC CERAMIC ELECT FILM FILM 0.0047µF 470pF 330µF 1µF 0.22µF 10% 20% 10% 5% 250V 250V 450V 400V 50V C613 C614 C620 C621 C622 1-126-967-11 1-163-251-11 1-128-990-11 1-104-330-91 1-104-330-91 ELECT 47µF CERAMIC CHIP 100pF FILM 27000pF CERAMIC 470pF CERAMIC 470pF 20% 5% 5% 10% 10% 50V 50V 800V 1KV 1KV C623 C624 C625 C626 C627 1-136-171-00 1-136-171-00 1-136-167-00 1-136-167-00 1-104-330-91 FILM FILM FILM FILM CERAMIC 5% 5% 5% 5% 10% 50V 50V 50V 50V 1KV C629 C630 C631 C633 C634 1-137-370-11 1-163-005-11 1-104-665-11 1-164-161-11 1-163-009-11 FILM 0.01µF CERAMIC CHIP 470pF ELECT 100µF CERAMIC CHIP 0.0022µF CERAMIC CHIP 0.001µF 5% 10% 20% 10% 10% 50V 50V 25V 50V 50V C650 C651 C652 C653 C654 1-107-656-11 1-107-651-11 1-128-563-11 1-128-581-11 1-126-943-11 ELECT ELECT ELECT ELECT ELECT 100µF 4.7µF 100µF 4.7µF 2200µF 20% 20% 20% 20% 20% 250V 250V 100V 100V 25V C655 C656 1-104-664-11 ELECT 1-126-943-11 ELECT 47µF 2200µF 20% 25V 20% 25V 0.33µF 0.33µF 0.15µF 0.15µF 470pF 20% 20% 10% 10% CN601*1-580-689-11 CN602*1-691-960-11 CN603*1-691-960-11 CN650*1-564-510-11 CN652*1-564-512-11 275V 275V 250V 250V 250V PIN, CONNECTOR (PC BOARD) 4P PIN, CONNECTOR (PC BOARD) 3P PIN, CONNECTOR (PC BOARD) 3P PLUG, CONNECTOR 7P PLUG, CONNECTOR 9P CN653*1-564-509-11 PLUG, CONNECTOR 6P CN654*1-564-511-11 PLUG, CONNECTOR 8P <DIODE> 7-4 D610 ¡ 8-719-510-53 D612 8-719-911-19 D613 8-719-304-63 D620 8-719-911-19 D631 8-719-063-73 DIODE D4SB60L DIODE 1SS119-25 DIODE RM11C DIODE 1SS119-25 DIODE D1NL20U-TR D632 D633 D634 D635 D637 8-719-059-23 8-719-069-63 8-719-911-19 8-719-110-53 8-719-911-19 DIODE P6KE200AG23 DIODE ERB38-06V1 DIODE 1SS119-25 ZENER DIODE RD20ESB2 DIODE 1SS119-25 D650 D651 D652 D653 D654 8-719-064-49 8-719-063-73 8-719-052-91 8-719-022-97 8-719-022-97 DIODE D4SBL40 DIODE D1NL20U-TR DIODE D4SBS4-F DIODE D2S4MF DIODE D2S4MF D655 D656 D660 D661 D663 8-719-063-73 8-719-911-19 8-719-110-57 8-719-110-31 8-719-911-19 DIODE D1NL20U-TR DIODE 1SS119-25 ZENER DIODE RD22ESB2 ZENER DIODE RD12ESB2 DIODE 1SS119-25 D664 D665 D666 D680 8-719-110-57 8-719-911-19 8-719-911-19 8-719-989-87 ZENER DIODE RD22ESB2 DIODE 1SS119-25 DIODE 1SS119-25 DIODE YG802C09 GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. (g) DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK D681 8-719-109-89 ZENER DIODE RD5.6ESB2 Q652 8-729-120-28 TRANSISTOR 2SC1623-L5L6 D682 D683 D690 D692 8-719-121-26 8-719-911-19 8-719-911-19 8-719-911-19 Q653 Q654 Q667 Q670 Q671 8-729-120-28 TRANSISTOR 2SC1623-L5L6 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R Q691 8-729-119-78 TRANSISTOR 2SC2785-HFE ZENER DIODE RD9.1ESL2 DIODE 1SS119-25 DIODE 1SS119-25 DIODE 1SS119-25 <FUSE> F601 ¡ 1-576-233-11 FUSE (H.B.C.) (6.3A/250V) <RESISTOR> <FERRITE BEAD> FB630 1-410-396-41 FERRITE FB632 ¡ 1-410-397-31 FERRITE 0.45µH 1.1µH <IC> IC610 IC630 IC650 IC651 IC652 8-749-015-89 8-759-535-32 8-749-012-49 8-759-592-79 8-759-496-15 IC MZ1530 IC FA13842P IC DM-57N IC BA00AST-V5 IC BA05ST-V5 IC653 8-759-450-47 IC BA05T IC654 8-759-643-66 IC µPC2912HF (12) IC680 8-759-321-95 IC HA17431PA <COIL> L610 L611 L650 L651 L652 1-419-126-21 1-411-674-11 1-414-742-21 1-414-742-21 1-412-529-11 COIL, CHOKE (AFC) INDUCTOR INDUCTOR INDUCTOR INDUCTOR L653 L680 1-412-529-11 INDUCTOR 1-414-742-21 INDUCTOR 216µH 68µH 22µH 22µH 22µH 22µH 22µH <PHOTO COUPLER> PH620 8-749-924-35 PHOTO COUPLER ON3171-R PH630 8-749-924-35 PHOTO COUPLER ON3171-R <IC LINK> PS650¡ 1-533-593-31 LINK, IC (2A/90V AC, 60V DC) <TRANSISTOR> Q603 Q610 Q621 Q630 Q631 8-729-045-39 8-729-119-76 8-729-119-78 8-729-045-03 8-729-041-66 TRANSISTOR MX0842AB-F TRANSISTOR 2SA1175-HFE TRANSISTOR 2SC2785-HFE TRANSISTOR 2SK2647-01MR-F91 TRANSISTOR 2SC4015TV2 Q632 Q633 Q650 Q651 8-729-041-66 8-729-120-28 8-729-119-76 8-729-230-45 TRANSISTOR 2SC4015TV2 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1175-HFE TRANSISTOR 2SC2458-YGR 7-5 R601 ¡ 1-220-825-91 CARBON R602 1-216-465-11 METAL OXIDE R603 1-247-895-91 CARBON R604 1-216-113-00 RES-CHIP R605 1-216-113-00 RES-CHIP 330K 27K 470K 470K 470K 5% 5% 5% 5% 5% 1/2W 2W F 1/4W 1/10W 1/10W R606 R607 R608 R609 R610 1-216-097-91 RES-CHIP 1-216-097-91 RES-CHIP 1-216-073-00 RES-CHIP 1-216-069-00 RES-CHIP 1-217-152-00 METAL 100K 100K 10K 6.8K 0.33 5% 5% 5% 5% 10% 1/10W 1/10W 1/10W 1/10W 2W R611 R612 R613 R614 R615 1-217-153-00 METAL 1-249-429-11 CARBON 1-216-089-91 RES-CHIP 1-247-807-31 CARBON 1-249-427-11 CARBON 0.47 10K 47K 100 6.8K 10% 5% 5% 5% 5% 2W 1/4W 1/10W 1/4W 1/4W R616 R617 R618 R620 R621 1-216-671-11 METAL CHIP 1-249-417-11 CARBON 1-216-369-00 METAL OXIDE 1-202-933-61 FUSIBLE 1-249-432-11 CARBON 6.8K 1K 1 0.1 18K 0.5% 5% 5% 10% 5% 1/10W 1/4W 2W F 1/2W F 1/4W R622 R623 R624 R625 R626 1-216-089-91 RES-CHIP 1-218-642-11 METAL OXIDE 1-218-642-11 METAL OXIDE 1-216-349-00 METAL OXIDE 1-216-349-00 METAL OXIDE 47K 100K 100K 1 1 5% 5% 5% 5% 5% 1/10W 1W F 1W F 1W F 1W F R627 R628 R629 R630 R632 1-216-683-11 METAL CHIP 1-216-695-11 METAL CHIP 1-216-683-11 METAL CHIP 1-249-387-11 CARBON 1-215-399-00 METAL 22K 68K 22K 3.3 120 0.5% 0.5% 0.5% 5% 1% 1/10W 1/10W 1/10W 1/4W F 1/4W R633 R634 R635 R636 R637 1-260-135-11 CARBON 1-260-135-11 CARBON 1-216-465-11 METAL OXIDE 1-247-863-91 CARBON 1-219-134-11 FUSIBLE 1M 1M 27K 22K 0.1 5% 5% 5% 5% 10% 1/2W 1/2W 2W F 1/4W 1/4W R638 R649 R650 R652 R653 1-219-134-11 FUSIBLE 1-249-437-11 CARBON 1-216-057-00 RES-CHIP 1-216-113-00 RES-CHIP 1-249-413-11 CARBON 0.1 47K 2.2K 470K 470 10% 5% 5% 5% 5% 1/4W 1/4W F 1/10W 1/10W 1/4W R654 R655 R656 R657 R658 1-211-796-11 FUSIBLE 1-216-065-91 RES-CHIP 1-260-292-11 CARBON 1-249-443-11 CARBON 1-216-073-00 RES-CHIP 1 4.7K 1 0.47 10K 5% 5% 5% 5% 5% 1/2W F 1/10W 1/2W 1/4W F 1/10W GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. (g)(d) REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. R659 R660 R661 R662 R663 1-216-049-91 1-216-073-00 1-247-807-31 1-216-073-00 1-216-073-00 RES-CHIP RES-CHIP CARBON RES-CHIP RES-CHIP 1K 10K 100 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/4W 1/10W 1/10W R664 R665 R666 R667 R668 1-216-073-00 1-216-057-00 1-216-073-00 1-216-089-91 1-215-457-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL 10K 2.2K 10K 47K 33K 5% 5% 5% 5% 1% 1/10W 1/10W 1/10W 1/10W 1/4W R670 R671 R672 R673 R674 1-216-677-11 1-216-677-11 1-216-664-11 1-216-073-00 1-216-097-91 METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 12K 12K 3.6K 10K 100K 0.5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R675 R676 R677 R678 R680 1-216-668-11 1-216-663-11 1-216-661-11 1-216-391-11 1-215-475-00 METAL CHIP METAL CHIP METAL CHIP METAL OXIDE METAL 5.1K 3.3K 2.7K 1.5 180K 0.5% 0.5% 0.5% 5% 1% 1/10W 1/10W 1/10W 3W F 1/4W R681 R682 R683 R684 R685 1-216-073-00 1-216-049-91 1-216-057-00 1-216-073-00 1-216-049-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 1K 2.2K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R686 R687 R688 R693 R694 1-216-033-00 1-216-081-00 1-215-473-00 1-260-085-11 1-216-073-00 RES-CHIP RES-CHIP METAL CARBON RES-CHIP 220 22K 150K 68 10K 5% 5% 1% 5% 5% 1/10W 1/10W 1/4W 1/2W 1/10W R695 R696 1-216-065-91 RES-CHIP 1-249-407-11 CARBON 4.7K 150 5% 5% 1/10W 1/4W DESCRIPTION REMARK <VARISTOR> VDR601 ¡ 1-801-268-51 VARISTOR TNR14V471K660 VDR602 ¡ 1-810-622-11 VARISTOR ******************************************************************************* * A-1346-859-B D BOARD, COMPLETE **************************** 3-710-578-01 4-070-828-01 4-070-829-02 4-070-830-01 4-382-854-11 COVER, VOLUME, 6 MOLD (RV901) INSULATING SHEET (Q515) INSULATING SHEET (IC502) INSULATING SHEET (IC701) SCREW (M3X10), P, SW (+) (IC701, Q704, Q705, Q905, Q906, R918) 7-685-647-79 SCREW +BVTP 3X10 TYPE2 TT(B) (D511, IC502, Q508, Q515, R547) <CAPACITOR> <RELAY> RY602 ¡ 1-755-318-11 RELAY, POWER RY603 ¡ 1-755-067-21 RELAY <SPARK GAP> SG601 ¡ 1-533-982-11 GAP, SPARK <TRANSFORMER> T601 ¡ 1-429-180-11 TRANSFORMER, LINE FILTER T620 1-433-894-11 TRANSFORMER, CONVERTER (PIT) T621 1-429-992-11 TRANSFORMER, CONVERTER (PRT) T630 1-433-895-31 TRANSFORMER, CONVERTER (SRT) <THERMISTOR> TH601 ¡ 1-809-260-11 THERMISTOR, POWER THP601¡ 1-809-827-31 THERMISTOR, POSITIVE 7-6 C501 C502 C503 C504 C505 1-163-021-91 1-136-169-00 1-163-021-91 1-163-017-00 1-163-021-91 CERAMIC CHIP 0.01µF FILM 0.22µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.0047µF CERAMIC CHIP 0.01µF 10% 5% 10% 10% 10% 50V 50V 50V 50V 50V C506 C507 C508 C509 C510 1-137-194-81 1-136-169-00 1-126-965-11 1-117-670-31 1-117-398-11 FILM FILM ELECT FILM ELECT 5% 5% 20% 5% 20% 50V 50V 50V 250V 250V C511 C512 C513 C514 C515 1-163-113-00 1-163-259-91 1-163-017-00 1-106-375-12 1-163-021-91 CERAMIC CHIP 68pF CERAMIC CHIP 220pF CERAMIC CHIP 0.0047µF MYLAR 0.022µF CERAMIC CHIP 0.01µF 5% 50V 5% 50V 10% 50V 200V 10% 50V C516 C517 C518 C519 C520 1-126-935-11 1-163-021-91 1-137-194-81 1-163-021-91 1-107-914-11 ELECT 470µF CERAMIC CHIP 0.01µF FILM 0.47µF CERAMIC CHIP 0.01µF ELECT 1000µF 20% 10% 5% 10% 20% 16V 50V 50V 50V 25V C521 C522 C523 C524 C525 1-117-666-11 1-137-368-11 1-137-368-11 1-163-133-00 1-104-760-11 FILM 0.39µF FILM 0.0047µF FILM 0.0047µF CERAMIC CHIP 470pF CERAMIC CHIP 0.047µF 5% 5% 5% 5% 10% 250V 50V 50V 50V 50V C526 C527 C528 C529 C530 1-163-021-91 1-163-021-91 1-117-663-31 1-104-665-11 1-163-021-91 CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF FILM 0.22µF ELECT 100µF CERAMIC CHIP 0.01µF 10% 10% 5% 20% 10% 50V 50V 250V 25V 50V C531 C532 C533 C534 1-107-846-11 1-163-009-11 1-107-889-11 1-107-889-11 FILM 0.1µF CERAMIC CHIP 0.001µF ELECT 220µF ELECT 220µF 5% 10% 20% 20% 250V 50V 25V 25V 0.47µF 0.22µF 22µF 0.82µF 33µF GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. (d) DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C535 1-163-021-91 CERAMIC CHIP 0.01µF 10% 50V C536 C537 C538 C539 C540 1-126-967-11 1-113-694-11 1-163-021-91 1-163-017-00 1-106-343-00 ELECT 47µF FILM 0.056µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.0047µF MYLAR 0.001µF 20% 5% 10% 10% 10% 50V 400V 50V 50V 200V C541 C542 C543 C544 C545 1-164-161-11 1-163-021-91 1-135-350-11 1-125-925-11 1-107-597-11 CERAMIC CHIP 0.0022µF CERAMIC CHIP 0.01µF FILM 3600pF FILM MELF 0.027µF CERAMIC 22pF 10% 10% 3% 5% 5% 50V 50V 1.8KV 400V 500V C546 C547 C548 C549 C550 1-107-444-11 1-130-061-91 1-162-134-11 1-130-495-00 1-127-833-11 CERAMIC FILM CERAMIC FILM FILM 5% 5% 10% 5% 5% 2KV 630V 2KV 50V 400V C551 C552 C554 C555 C556 1-163-017-00 1-163-021-91 1-107-444-11 1-107-683-11 1-115-356-11 CERAMIC CHIP 0.0047µF CERAMIC CHIP 0.01µF CERAMIC 100pF ELECT 2.2µF FILM 1.2µF 10% 50V 10% 50V 5% 2KV 250V 5% 250V C557 C558 C559 C560 C561 1-163-021-91 1-104-665-11 1-107-649-11 1-163-021-91 1-104-664-11 CERAMIC CHIP 0.01µF ELECT 100µF ELECT 2.2µF CERAMIC CHIP 0.01µF ELECT 47µF 10% 20% 20% 10% 20% 50V 25V 250V 50V 25V C562 C563 C564 C565 C566 1-163-021-91 1-163-011-11 1-126-960-11 1-164-004-11 1-137-370-11 CERAMIC CHIP 0.01µF CERAMIC CHIP 0.0015µF ELECT 1µF CERAMIC CHIP 0.1µF FILM 0.01µF 10% 10% 20% 10% 5% 50V 50V 50V 25V 50V C567 C568 C571 C572 C573 1-164-161-11 1-104-760-11 1-163-227-11 1-163-009-11 1-106-375-12 CERAMIC CHIP 0.0022µF CERAMIC CHIP 0.047µF CERAMIC CHIP 10pF CERAMIC CHIP 0.001µF MYLAR 0.022µF 10% 10% 0.5pF 10% 50V 50V 50V 50V 200V CN501*1-564-509-11 PLUG, CONNECTOR 6P CN502*1-564-510-11 PLUG, CONNECTOR 7P CN503*1-508-879-11 BASE POST CN504 1-784-786-11 CONNECTOR, FFC 25P CN505 1-784-786-11 CONNECTOR, FFC 25P C574 C575 C577 C701 C702 1-163-017-00 1-163-021-91 1-126-964-11 1-128-560-11 1-128-562-11 CERAMIC CHIP 0.0047µF CERAMIC CHIP 0.01µF ELECT 10µF ELECT 22µF ELECT 47µF 10% 10% 20% 20% 20% 50V 50V 50V 100V 100V CN506 1-764-101-11 PIN, CONNECTOR (PC BOARD) 2P CN508*1-564-511-11 PLUG, CONNECTOR 8P CN509*1-778-955-11 PIN, CONNECTOR (PC BOARD) 10P C703 C704 C706 C707 C708 1-104-331-11 1-104-568-11 1-164-004-11 1-130-495-00 1-126-942-61 CERAMIC 0.0022µF CERAMIC 470pF CERAMIC CHIP 0.1µF FILM 0.1µF ELECT 1000µF 10% 10% 10% 5% 20% 1KV 2KV 25V 50V 25V C709 C710 C711 C712 C713 1-163-021-91 1-107-894-11 1-163-019-00 1-106-228-00 1-126-942-61 CERAMIC CHIP 0.01µF ELECT 220µF CERAMIC CHIP 0.0068µF MYLAR 0.22µF ELECT 1000µF 10% 20% 10% 10% 20% 50V 35V 50V 100V 25V C715 C720 C901 C902 C903 1-164-004-11 1-126-964-11 1-163-021-91 1-104-665-11 1-126-964-11 CERAMIC CHIP 0.1µF ELECT 10µF CERAMIC CHIP 0.01µF ELECT 100µF ELECT 10µF 10% 20% 10% 20% 20% 25V 50V 50V 25V 50V 100pF 0.0015µF 470pF 0.1µF 0.15µF C905 C907 C908 C909 C910 1-163-127-00 CERAMIC CHIP 270pF 1-163-257-11 CERAMIC CHIP 180pF 1-163-021-91 CERAMIC CHIP 0.01µF 1-126-935-11 ELECT 470µF 1-126-962-11 ELECT 3.3µF 5% 5% 10% 20% 20% 50V 50V 50V 16V 50V C912 C913 C914 C915 C916 1-106-383-00 MYLAR 1-119-748-11 ELECT 1-106-383-00 MYLAR 1-136-169-00 FILM 1-117-626-11 FILM 0.047µF 33µF 0.047µF 0.22µF 2000pF 10% 20% 10% 5% 3% 200V 400V 200V 50V 1.2KV C917 C918 C919 C920 C921 1-117-665-11 FILM 1-106-359-00 MYLAR 1-115-350-51 CERAMIC 1-137-372-11 FILM 1-106-228-00 MYLAR 0.33µF 0.0047µF 0.0047µF 0.022µF 0.22µF 5% 250V 10% 100V 2KV 5% 50V 10% 100V C922 C923 C924 C925 C926 1-106-220-00 MYLAR 1-106-355-12 MYLAR 1-106-220-00 MYLAR 1-126-967-11 ELECT 1-126-964-11 ELECT 0.1µF 0.0033µF 0.1µF 47µF 10µF 10% 10% 10% 20% 20% 100V 200V 100V 50V 50V C927 C928 C929 C930 C931 1-163-243-11 CERAMIC CHIP 47pF 1-163-133-00 CERAMIC CHIP 470pF 1-164-004-11 CERAMIC CHIP 0.1µF 1-163-227-11 CERAMIC CHIP 10pF 1-126-964-11 ELECT 10µF 5% 5% 10% 0.5pF 20% 50V 50V 25V 50V 50V C932 C933 C935 1-163-021-91 CERAMIC CHIP 0.01µF 1-126-960-11 ELECT 1µF 1-163-275-11 CERAMIC CHIP 0.001µF 10% 50V 20% 50V 5% 50V <CONNECTOR> <DIODE> 7-7 D504 D505 D506 D507 D508 8-719-988-61 DIODE 1SS355TE-17 8-719-110-36 ZENER DIODE RD13ESB2 8-719-991-33 DIODE 1SS133T-77 8-719-063-89 DIODE YG911S3R 8-719-031-79 DIODE D5SC4M D509 D510 D511 D512 D513 8-719-991-33 DIODE 1SS133T-77 8-719-109-85 ZENER DIODE RD5.1ESB2 8-719-066-36 DIODE FMQ-G5GS 8-719-988-61 DIODE 1SS355TE-17 8-719-991-33 DIODE 1SS133T-77 D514 D515 D516 D517 8-719-991-33 DIODE 1SS133T-77 8-719-109-89 ZENER DIODE RD5.6ESB2 8-719-991-33 DIODE 1SS133T-77 8-719-951-30 DIODE ERA91-02 GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. (d) REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK D519 8-719-988-61 DIODE 1SS355TE-17 JR006 1-216-295-91 SHORT 0 D520 D522 D701 D702 D703 8-719-988-61 8-719-988-61 8-719-991-33 8-719-991-33 8-719-991-33 DIODE 1SS355TE-17 DIODE 1SS355TE-17 DIODE 1SS133T-77 DIODE 1SS133T-77 DIODE 1SS133T-77 JR008 JR009 JR010 JR011 JR012 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 1-216-296-91 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 D706 D707 D708 D709 D710 8-719-979-58 8-719-109-85 8-719-908-03 8-719-948-45 8-719-109-85 DIODE EGP10D ZENER DIODE RD5.1ESB2 DIODE GP08D DIODE ERA22-08 ZENER DIODE RD5.1ESB2 JR013 JR014 JR015 JR016 1-216-295-91 1-216-296-91 1-216-296-91 1-216-295-91 SHORT SHORT SHORT SHORT 0 0 0 0 D901 D902 D904 D905 D906 8-719-991-33 8-719-110-31 8-719-988-61 8-719-110-36 8-719-063-89 DIODE 1SS133T-77 ZENER DIODE RD12ESB2 DIODE 1SS355TE-17 ZENER DIODE RD13ESB2 DIODE YG911S3R D907 D908 D909 D910 D912 8-719-930-97 8-719-018-82 8-719-930-97 8-719-991-33 8-719-979-58 ZENER DIODE HZS16NB2TD DIODE RGP02-20EL-6394 ZENER DIODE HZS16NB2TD DIODE 1SS133T-77 DIODE EGP10D D913 D914 D915 D917 D918 8-719-991-33 8-719-991-33 8-719-929-72 8-719-988-61 8-719-991-33 DIODE 1SS133T-77 DIODE 1SS133T-77 ZENER DIODE HZS33NB2 DIODE 1SS355TE-17 DIODE 1SS133T-77 D919 D920 D921 D922 D923 8-719-991-33 8-719-928-85 8-719-988-61 8-719-018-82 8-719-988-61 DIODE 1SS133T-77 ZENER DIODE HZS4.7NB2 DIODE 1SS355TE-17 DIODE RGP02-20EL-6394 DIODE 1SS355TE-17 <COIL> L501 L502 L503 L504 L505 1-412-537-31 1-406-673-11 1-406-671-11 1-406-675-11 1-416-401-31 INDUCTOR COIL, CHOKE COIL, CHOKE COIL, CHOKE COIL, CHOKE 100µH 2.2mH 1mH 4.7mH 5mH L901 L902 1-412-537-31 INDUCTOR 1-406-660-41 COIL, CHOKE 100µH 15µH <TRANSISTOR> Q501 Q502 Q503 Q504 Q505 8-729-048-49 8-729-120-28 8-729-901-97 8-729-901-87 8-729-901-97 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1036K-Q TRANSISTOR 2SC2411K-CQ TRANSISTOR 2SA1036K-Q Q506 Q507 Q508 Q509 Q510 8-729-048-49 8-729-048-49 8-729-048-53 8-729-820-73 8-729-048-49 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SJ569LS-CB11 TRANSISTOR 2SC3746 TRANSISTOR 2SK3262-01MR-F119 Q511 Q512 Q513 Q514 Q515 8-729-048-49 8-729-048-49 8-729-048-49 8-729-140-50 8-729-048-48 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SC3209LK TRANSISTOR 2SC5570 (LBSONY) Q516 Q517 Q518 Q519 Q520 8-729-024-95 8-729-048-49 8-729-019-01 8-729-033-25 8-729-120-28 TRANSISTOR 2SB1565EF TRANSISTOR 2SK3262-01MR-F119 TRANSISTOR 2SD2394-EF TRANSISTOR DTC114GKA TRANSISTOR 2SC1623-L5L6 Q521 Q522 Q523 Q524 Q525 8-729-120-28 8-729-120-28 8-729-120-28 8-729-026-49 8-729-048-49 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-R TRANSISTOR 2SK3262-01MR-F119 Q526 Q701 Q702 Q703 Q704 8-729-027-35 8-729-800-32 8-729-178-43 8-729-204-91 8-729-207-82 TRANSISTOR DTA143TKA-T146 TRANSISTOR 2SC2362K-G TRANSISTOR 2SC2784-E TRANSISTOR 2SA1049-GR TRANSISTOR 2SC3421-Y Q705 Q706 Q707 8-729-207-89 TRANSISTOR 2SA1358-Y 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 8-729-046-80 TRANSISTOR 2SC4634LS-CB11 <FERRITE BEAD> FB501 FB502 FB503 FB504 FB505 1-410-397-21 1-410-397-21 1-412-911-11 1-412-911-11 1-412-911-11 FERRITE FERRITE FERRITE FERRITE FERRITE 1.1µH 1.1µH 1.1µH 1.1µH 1.1µH FB506 1-410-397-21 FERRITE FB507 1-410-397-21 FERRITE FB901 1-410-397-21 FERRITE 1.1µH 1.1µH 1.1µH <IC> IC501 IC502 IC503 IC701 IC901 8-759-585-82 8-759-803-42 8-759-058-50 8-759-444-82 8-759-585-81 IC BA9759F-E2 IC LA6500-FA IC XRA10324AF IC LA7841L IC BA9758FS-E2 <CHIP CONDUCTOR> JR002 JR003 JR004 JR005 1-216-296-91 1-216-295-91 1-216-295-91 1-216-296-91 SHORT SHORT SHORT SHORT 0 0 0 0 7-8 GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. (d) DESCRIPTION REMARK Q903 Q904 8-729-901-87 TRANSISTOR 2SC2411K-CQ 8-729-901-97 TRANSISTOR 2SA1036K-Q Q905 Q906 Q907 Q908 8-729-048-53 8-729-044-21 8-729-033-26 8-729-033-25 REF.NO. PART NO. TRANSISTOR 2SJ569LS-CB11 TRANSISTOR 2SK2655-01R-F165 TRANSISTOR DTA114GKAT146 TRANSISTOR DTC114GKA DESCRIPTION REMARK R547 R548 R549 R550 1-219-726-11 METAL 1-249-437-11 CARBON 1-260-288-11 CARBON 1-260-288-11 CARBON 2.2 47K 0.47 0.47 5% 5% 5% 5% 10W 1/4W 1/2W 1/2W R551 R552 R553 R554 R555 1-216-049-91 RES-CHIP 1-216-097-91 RES-CHIP 1-247-815-91 CARBON 1-216-679-11 METAL CHIP 1-216-675-91 METAL CHIP 1K 100K 220 15K 10K 5% 5% 5% 0.5% 0.5% 1/10W 1/10W 1/4W 1/10W 1/10W R556 R557 R558 R559 R560 1-216-683-11 METAL CHIP 1-216-423-11 METAL OXIDE 1-249-437-11 CARBON 1-216-073-00 RES-CHIP 1-216-675-91 METAL CHIP 22K 27 47K 10K 10K 0.5% 5% 5% 5% 0.5% 1/10W 1W F 1/4W 1/10W 1/10W R561 R562 R563 R564 R565 1-215-443-00 METAL 1-216-677-11 METAL CHIP 1-216-049-91 RES-CHIP 1-216-677-11 METAL CHIP 1-216-097-91 RES-CHIP 8.2K 12K 1K 12K 100K 1% 0.5% 5% 0.5% 5% 1/4W 1/10W 1/10W 1/10W 1/10W R566 R567 R568 R569 R570 1-216-687-11 METAL CHIP 1-214-840-00 METAL 1-216-665-11 METAL CHIP 1-216-691-11 METAL CHIP 1-260-332-51 CARBON 33K 100 3.9K 47K 2.2K 0.5% 1% 0.5% 0.5% 5% 1/10W 1/2W 1/10W 1/10W 1/2W R571 R572 R573 R574 R575 1-249-425-11 CARBON 1-216-385-11 METAL OXIDE 1-249-437-11 CARBON 1-216-097-91 RES-CHIP 1-216-672-11 METAL CHIP 4.7K 0.47 47K 100K 7.5K 5% 5% 5% 5% 0.5% 1/4W 3W F 1/4W 1/10W 1/10W R576 R577 R578 R579 R580 1-215-869-11 METAL OXIDE 1-260-310-71 CARBON 1-216-049-91 RES-CHIP 1-216-049-91 RES-CHIP 1-214-840-00 METAL 1K 33 1K 1K 100 5% 5% 5% 5% 1% 1W F 1/2W 1/10W 1/10W 1/2W R581 R582 R583 R584 R585 1-260-316-51 CARBON 1-214-840-00 METAL 1-249-437-11 CARBON 1-249-437-11 CARBON 1-216-073-00 RES-CHIP 100 100 47K 47K 10K 5% 1% 5% 5% 5% 1/2W 1/2W 1/4W 1/4W 1/10W R586 R587 R588 R589 R590 1-216-683-11 METAL CHIP 1-215-886-11 METAL OXIDE 1-260-085-11 CARBON 1-216-057-00 RES-CHIP 1-216-057-00 RES-CHIP 22K 100 68 2.2K 2.2K 0.5% 5% 5% 5% 5% 1/10W 2W F 1/2W 1/10W 1/10W R591 R593 R594 R595 R597 1-247-807-31 CARBON 1-216-073-00 RES-CHIP 1-216-683-11 METAL CHIP 1-216-659-11 METAL CHIP 1-216-073-00 RES-CHIP 100 10K 22K 2.2K 10K 5% 5% 0.5% 0.5% 5% 1/4W 1/10W 1/10W 1/10W 1/10W R598 R599 R701 R702 R703 1-216-675-91 METAL CHIP 1-216-657-11 METAL CHIP 1-216-049-91 RES-CHIP 1-249-393-11 CARBON 1-215-459-00 METAL 10K 1.8K 1K 10 39K 0.5% 0.5% 5% 5% 1% 1/10W 1/10W 1/10W 1/4W F 1/4W R704 R705 1-216-655-11 METAL CHIP 1-249-413-11 CARBON 1.5K 470 0.5% 1/10W 5% 1/4W F <RESISTOR> R501 R502 R503 R504 R505 1-215-884-11 1-216-059-00 1-216-049-91 1-216-049-91 1-216-049-91 METAL OXIDE RES-CHIP RES-CHIP RES-CHIP RES-CHIP 47 2.7K 1K 1K 1K 5% 5% 5% 5% 5% 2W F 1/10W 1/10W 1/10W 1/10W R506 R507 R508 R509 R510 1-216-049-91 1-216-097-91 1-247-815-91 1-216-049-91 1-216-675-91 RES-CHIP RES-CHIP CARBON RES-CHIP METAL CHIP 1K 100K 220 1K 10K 5% 5% 5% 5% 0.5% 1/10W 1/10W 1/4W 1/10W 1/10W R511 R512 R513 R514 R515 1-216-065-91 1-215-453-00 1-216-049-91 1-216-097-91 1-216-049-91 RES-CHIP METAL RES-CHIP RES-CHIP RES-CHIP 4.7K 22K 1K 100K 1K 5% 1% 5% 5% 5% 1/10W 1/4W 1/10W 1/10W 1/10W R516 R517 R518 R519 R520 1-216-049-91 1-216-687-11 1-216-691-11 1-216-081-00 1-247-791-91 RES-CHIP METAL CHIP METAL CHIP RES-CHIP CARBON 1K 33K 47K 22K 22 5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/4W R521 R522 R523 R524 R525 1-216-667-11 1-249-437-11 1-216-033-00 1-216-049-91 1-216-065-91 METAL CHIP CARBON RES-CHIP RES-CHIP RES-CHIP 4.7K 47K 220 1K 4.7K 0.5% 5% 5% 5% 5% 1/10W 1/4W 1/10W 1/10W 1/10W R526 R527 R528 R529 R530 1-216-097-91 1-216-673-11 1-216-677-11 1-216-057-00 1-216-049-91 RES-CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 100K 8.2K 12K 2.2K 1K 5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R531 R532 R533 R534 R535 1-216-097-91 1-215-860-11 1-211-796-11 1-216-689-11 1-216-065-91 RES-CHIP METAL OXIDE FUSIBLE METAL CHIP RES-CHIP 100K 33 1 39K 4.7K 5% 5% 5% 0.5% 5% 1/10W 1W F 1/2W F 1/10W 1/10W R536 R537 R538 R539 R540 1-216-683-11 1-249-437-11 1-216-049-91 1-216-097-91 1-215-909-11 METAL CHIP CARBON RES-CHIP RES-CHIP METAL OXIDE 22K 47K 1K 100K 47 0.5% 5% 5% 5% 5% 1/10W 1/4W 1/10W 1/10W 3W F R541 R542 R543 R544 R545 1-216-295-91 1-249-437-11 1-216-677-11 1-216-049-91 1-216-097-91 SHORT CARBON METAL CHIP RES-CHIP RES-CHIP 0 47K 12K 1K 100K R546 1-216-381-11 METAL OXIDE 0.22 5% 0.5% 5% 5% 1/4W 1/10W 1/10W 1/10W 5% 3W F 7-9 The components identified by [ in this manual have been carefully factoryselected for eachset in order to satisfy regulations regarding X-ray radiation. Should replacement be required, replace only with the value originally used. GDM-5403 (d) REF.NO. PART NO. DESCRIPTION REMARK R706 R707 R708 1-249-389-11 CARBON 4.7 1-249-389-11 CARBON 4.7 1-215-881-11 METAL OXIDE 15 5% 5% 5% 1/4W F 1/4W F 2W F R709 R710 R711 R713 R714 1-216-049-91 1-216-073-00 1-216-049-91 1-216-059-00 1-216-057-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 10K 1K 2.7K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R715 R716 R717 R718 R719 1-249-389-11 1-216-689-11 1-216-073-00 1-216-681-11 1-216-663-11 CARBON RES-CHIP RES-CHIP METAL CHIP METAL CHIP 4.7 39K 10K 18K 3.3K 5% 5% 5% 0.5% 0.5% 1/4W F 1/10W 1/10W 1/10W 1/10W R720 R721 R722 R723 R724 1-216-073-00 1-216-073-00 1-260-292-11 1-216-663-11 1-216-659-11 RES-CHIP RES-CHIP CARBON METAL CHIP METAL CHIP 10K 10K 1 3.3K 2.2K 5% 5% 5% 0.5% 0.5% 1/10W 1/10W 1/2W 1/10W 1/10W R725 R726 R727 R728 R729 1-214-798-21 1-214-798-21 1-249-381-11 1-215-865-11 1-260-292-11 METAL METAL CARBON METAL OXIDE CARBON 1.8 1.8 1 220 1 1% 1% 5% 5% 5% 1/2W 1/2W 1/4W F 1W F 1/2W R730 R731 R732 R901 R902 1-216-073-00 1-216-059-00 1-219-510-11 1-216-097-91 1-216-117-00 RES-CHIP RES-CHIP CARBON RES-CHIP RES-CHIP 10K 2.7K 470K 100K 680K 5% 5% 5% 5% 5% 1/10W 1/10W 1/2W 1/10W 1/10W R903 R904 R906 R907 R908 1-216-089-91 1-216-033-00 1-216-033-00 1-216-081-00 1-216-399-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL OXIDE 47K 220 220 22K 6.8 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 3W F R911 R912 R914 R915 R916 1-216-041-00 1-216-049-91 1-247-791-91 1-216-065-91 1-249-397-11 RES-CHIP RES-CHIP CARBON RES-CHIP CARBON 470 1K 22 4.7K 22 5% 5% 5% 5% 5% 1/10W 1/10W 1/4W 1/10W 1/4W F R917 R918 R919 R920 R921 1-211-824-71 1-219-727-11 1-219-748-11 1-216-089-91 1-249-429-11 FUSIBLE METAL CARBON RES-CHIP CARBON 220 68 4.7K 47K 10K 5% 5% 5% 5% 5% 1/2W F 10W 1/2W 1/10W 1/4W R922 R923 R924 R925 R926 1-249-389-11 1-218-762-11 1-216-073-00 1-220-825-11 1-219-746-11 CARBON METAL CHIP RES-CHIP CARBON CARBON 4.7 270K 10K 330K 1K 5% 0.5% 5% 5% 5% 1/4W F 1/10W 1/10W 1/2W 1/2W R927 R928 R929 R930 R931 1-219-746-11 1-216-668-11 1-216-675-91 1-216-653-11 1-216-653-11 CARBON METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 5.1K 10K 1.2K 1.2K 5% 0.5% 0.5% 0.5% 0.5% 1/2W 1/10W 1/10W 1/10W 1/10W R932 R933 R934 1-216-049-91 RES-CHIP 1-216-687-11 METAL CHIP 1-216-667-11 METAL CHIP 1K 33K 4.7K 5% 1/10W 0.5% 1/10W 0.5% 1/10W REF.NO. PART NO. The components identified ¡ marked are critical for safety. Replace only with the part number specified. DESCRIPTION REMARK R935 R937 1-216-089-91 RES-CHIP 1-216-065-91 RES-CHIP 47K 4.7K 5% 5% 1/10W 1/10W R939 R940 R941 R943 R945 1-216-049-91 1-216-073-00 1-216-025-91 1-216-065-91 1-216-025-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 10K 100 4.7K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1501 R1502 R1503 R1504 R1505 1-216-049-91 1-216-033-00 1-216-682-11 1-216-665-11 1-216-667-11 RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 1K 220 20K 3.9K 4.7K 5% 5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R1506 R1507 R1510 R1515 R1517 1-216-049-91 1-216-097-91 1-216-073-00 1-215-909-11 1-216-089-91 RES-CHIP RES-CHIP RES-CHIP METAL OXIDE RES-CHIP 1K 100K 10K 47 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 3W F 1/10W 100 5% 1/10W R1518 1-216-025-91 RES-CHIP <VARIABLE RESISTOR> [ RV901 ¡ 1-241-767-21RES, ADJ, CERMET 100K (HV ADJ) <RELAY> RY501 1-755-198-11 RELAY <SPARK GAP> SG901 1-517-499-21 GAP, SPARK SG902 1-519-422-11 GAP, SPARK SG903 1-519-422-11 GAP, SPARK <TRANSFORMER> T501 T502 T503 T505 T701 1-435-070-11 1-429-301-11 1-431-413-21 1-419-127-11 1-431-414-11 TRANSFORMER, HORIZONTAL DRIVE TRANSFORMER, FERRITE (HCT) TRANSFORMER, FERRITE (HST) COIL, HORIZONTAL LINEARITY TRANSFORMER, FERRITE (DFT) T901 1-416-402-11 INDUCTOR 500µH T902 ¡ X-4560-175-1 TRANSFORMER ASSY, FLYBACK (NX-4502//J1D4) <THERMISTOR> TH501 1-807-796-11 THERMISTOR TH502 1-807-796-11 THERMISTOR ******************************************************************************* 7-10 GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. (h)(j)(n) DESCRIPTION REMARK REF.NO. PART NO. * A-1372-740-AH BOARD, COMPLETE [ELSA, FORMAC] * A-1646-207-AH BOARD, COMPLETE [OEM STD] **************************** DESCRIPTION REMARK <THERMISTOR> TH801 1-807-796-11 THERMISTOR <CAPACITOR> C810 C814 1-126-791-11 ELECT 1-126-786-11 ELECT 10µF 47µF 20% 16V 20% 16V ******************************************************************************* * A-1388-260-BJ BOARD, COMPLETE *************************** <CONNECTOR> CN801*1-564-526-11 PLUG, CONNECTOR 11P <CONNECTOR> CN891*1-691-960-11 PIN, CONNECTOR (PC BOARD) 3P <DIODE> D801 8-719-064-11 DIODE SPR-325MVW <SWITCH> S891 ¡ 1-571-433-31 SWITCH, PUSH (AC POWER) <TRANSISTOR> Q801 Q802 Q803 Q804 8-729-119-78 8-729-119-78 8-729-029-40 8-729-029-40 TRANSISTOR 2SC2785-HFE TRANSISTOR 2SC2785-HFE TRANSISTOR DTA124ESA TRANSISTOR DTA124ESA ******************************************************************************* * A-1394-967-B N BOARD, COMPLETE **************************** <RESISTOR> R801 R802 R803 R804 R805 1-249-425-11 1-249-417-11 1-249-417-11 1-249-421-11 1-249-421-11 CARBON CARBON CARBON CARBON CARBON 4.7K 1K 1K 2.2K 2.2K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R806 R807 R811 R812 R813 1-249-425-11 1-249-429-11 1-249-429-11 1-249-429-11 1-247-863-91 CARBON CARBON CARBON CARBON CARBON 4.7K 10K 10K 10K 22K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R814 R815 R821 R822 R823 1-249-441-11 1-249-429-11 1-249-407-11 1-249-413-11 1-249-417-11 CARBON CARBON CARBON CARBON CARBON 100K 10K 150 470 1K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R824 1-249-419-11 CARBON 1.5K 5% 1/4W <CAPACITOR> <SWITCH> S801 S802 S803 S804 S805 1-692-431-21 1-692-431-21 1-692-431-21 1-692-431-21 1-692-431-21 SWITCH, TACTILE (RESET) SWITCH, TACTILE (ASC) SWITCH, TACTILE (V-) SWITCH, TACTILE (V+) SWITCH, TACTILE (MENU) S806 S807 1-692-431-21 SWITCH, TACTILE (H-) 1-692-431-21 SWITCH, TACTILE (H+) 7-11 C001 C002 C003 C005 C006 1-163-009-11 CERAMIC CHIP 0.001µF 1-163-009-11 CERAMIC CHIP 0.001µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-255-91 CERAMIC CHIP 150pF 1-163-235-11 CERAMIC CHIP 22pF 10% 10% 10% 5% 5% 50V 50V 50V 50V 50V C007 C008 C009 C010 C011 1-163-235-11 CERAMIC CHIP 22pF 1-164-004-11 CERAMIC CHIP 0.1µF 1-115-339-11 CERAMIC CHIP 0.1µF 1-126-967-11 ELECT 47µF 1-115-339-11 CERAMIC CHIP 0.1µF 5% 10% 10% 20% 10% 50V 25V 50V 50V 50V C012 C013 C014 C015 C016 1-126-967-11 ELECT 47µF 1-126-965-11 ELECT 22µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 20% 20% 10% 10% 10% 50V 50V 50V 50V 50V C017 C018 C019 C020 C021 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C022 C023 C024 C025 C026 1-163-021-91 CERAMIC CHIP 0.01µF 1-163-021-91 CERAMIC CHIP 0.01µF 1-164-161-11 CERAMIC CHIP 0.0022µF 1-163-009-11 CERAMIC CHIP 0.001µF 1-104-665-11 ELECT 100µF 10% 10% 10% 10% 20% 50V 50V 50V 50V 25V C027 C028 C029 C031 1-115-339-11 CERAMIC CHIP 0.1µF 1-163-220-11 CERAMIC CHIP 3pF 1-163-241-11 CERAMIC CHIP 39pF 1-126-964-11 ELECT 10µF 10% 50V 0.25pF 50V 5% 50V 20% 50V GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. (n) REF.NO. PART NO. DESCRIPTION REMARK C033 1-163-021-91 CERAMIC CHIP 0.01µF 10% 50V C036 C037 C038 C039 C040 1-163-037-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 CERAMIC CHIP 0.022µF ELECT 10µF ELECT 10µF ELECT 10µF ELECT 10µF 10% 20% 20% 20% 20% 50V 50V 50V 50V 50V C041 C042 C043 C044 C045 1-126-964-11 1-163-021-91 1-126-965-11 1-163-037-11 1-163-037-11 ELECT 10µF CERAMIC CHIP 0.01µF ELECT 22µF CERAMIC CHIP 0.022µF CERAMIC CHIP 0.022µF 20% 10% 20% 10% 10% 50V 50V 50V 50V 50V C046 C047 C048 C049 C050 1-163-037-11 1-163-037-11 1-163-021-91 1-126-964-11 1-126-964-11 CERAMIC CHIP 0.022µF CERAMIC CHIP 0.022µF CERAMIC CHIP 0.01µF ELECT 10µF ELECT 10µF 10% 10% 10% 20% 20% 50V 50V 50V 50V 50V C051 C052 C053 C054 C055 1-163-021-91 1-126-933-11 1-163-021-91 1-115-339-11 1-104-664-11 CERAMIC CHIP 0.01µF ELECT 100µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF ELECT 47µF 10% 20% 10% 10% 20% 50V 16V 50V 50V 25V C056 C057 C058 C059 C061 1-126-965-11 1-126-964-11 1-164-690-91 1-126-964-11 1-163-021-91 ELECT 22µF ELECT 10µF CERAMIC CHIP 0.0022µF ELECT 10µF CERAMIC CHIP 0.01µF 20% 20% 5% 20% 10% 50V 50V 50V 50V 50V C062 C063 C064 C065 C066 1-126-925-11 1-164-690-91 1-115-419-11 1-126-960-11 1-164-690-91 ELECT 470µF CERAMIC CHIP 0.0022µF CERAMIC CHIP 3300pF ELECT 1µF CERAMIC CHIP 0.0022µF 20% 5% 5% 20% 5% 10V 50V 25V 50V 50V C067 C068 C069 C070 C071 1-164-004-11 1-136-169-00 1-115-339-11 1-126-767-11 1-163-007-11 CERAMIC CHIP 0.1µF FILM 0.22µF CERAMIC CHIP 0.1µF ELECT 1000µF CERAMIC CHIP 680pF 10% 5% 10% 20% 10% 25V 50V 50V 16V 50V C072 C073 C074 C075 C077 1-126-942-61 1-115-339-11 1-163-137-00 1-163-251-11 1-115-339-11 ELECT 1000µF CERAMIC CHIP 0.1µF CERAMIC CHIP 680pF CERAMIC CHIP 100pF CERAMIC CHIP 0.1µF 20% 10% 5% 5% 10% 25V 50V 50V 50V 50V C078 C079 C080 C082 C083 1-136-169-00 1-163-021-91 1-126-967-11 1-104-664-11 1-163-021-91 FILM 0.22µF CERAMIC CHIP 0.01µF ELECT 47µF ELECT 47µF CERAMIC CHIP 0.01µF 5% 10% 20% 20% 10% 50V 50V 50V 25V 50V C084 C085 C086 C087 C089 1-126-964-11 1-163-021-91 1-163-021-91 1-126-964-11 1-163-021-91 ELECT 10µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF ELECT 10µF CERAMIC CHIP 0.01µF 20% 10% 10% 20% 10% 50V 50V 50V 50V 50V C090 C091 C094 C095 C096 1-163-021-91 1-126-933-11 1-164-004-11 1-117-722-11 1-163-021-91 CERAMIC CHIP 0.01µF ELECT 100µF CERAMIC CHIP 0.1µF ELECT 2200µF CERAMIC CHIP 0.01µF 10% 20% 10% 20% 10% 50V 16V 25V 10V 50V REF.NO. PART NO. DESCRIPTION REMARK C097 C098 C099 C1003 C1004 1-126-964-11 1-163-021-91 1-164-004-11 1-104-664-11 1-163-021-91 ELECT 10µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF ELECT 47µF CERAMIC CHIP 0.01µF 20% 10% 10% 20% 10% 50V 50V 25V 25V 50V C1005 C1006 C1007 C5002 C5003 1-163-005-11 1-164-161-11 1-115-339-11 1-126-964-11 1-126-933-11 CERAMIC CHIP 470pF CERAMIC CHIP 0.0022µF CERAMIC CHIP 0.1µF ELECT 10µF ELECT 100µF 10% 10% 10% 20% 20% 50V 50V 50V 50V 16V C5004 C5005 C5008 C5009 C5101 1-104-664-11 1-104-664-11 1-104-664-11 1-164-004-11 1-164-004-11 ELECT 47µF ELECT 47µF ELECT 47µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF 20% 20% 20% 10% 10% 25V 25V 25V 25V 25V C5103 C5105 C5106 C5108 C5110 1-164-004-11 1-104-664-11 1-164-004-11 1-164-004-11 1-104-664-11 CERAMIC CHIP 0.1µF ELECT 47µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF ELECT 47µF 10% 20% 10% 10% 20% 25V 25V 25V 25V 25V C5203 C5205 C5206 C5301 C5303 1-164-004-11 1-164-004-11 1-163-021-91 1-164-004-11 1-164-004-11 CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF 10% 10% 10% 10% 10% 25V 25V 50V 25V 25V C5304 C5305 C5306 C5308 C5310 1-163-021-91 1-104-664-11 1-164-004-11 1-164-004-11 1-104-664-11 CERAMIC CHIP 0.01µF ELECT 47µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.1µF ELECT 47µF 10% 20% 10% 10% 20% 50V 25V 25V 25V 25V C5401 C5403 C5404 C5406 C5408 1-164-004-11 1-163-021-91 1-163-021-91 1-164-004-11 1-163-005-11 CERAMIC CHIP 0.1µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF CERAMIC CHIP 470pF 10% 10% 10% 10% 10% 25V 50V 50V 25V 50V C5409 C5413 C5501 C5602 C5606 1-163-021-91 1-164-004-11 1-126-967-11 1-115-339-11 1-163-021-91 CERAMIC CHIP 0.01µF CERAMIC CHIP 0.1µF ELECT 47µF CERAMIC CHIP 0.1µF CERAMIC CHIP 0.01µF 10% 10% 20% 10% 10% 50V 25V 50V 50V 50V C5607 1-164-004-11 CERAMIC CHIP 0.1µF 10% 25V <CONNECTOR> CN001 1-784-500-11 CN002*1-564-511-11 CN007*1-564-512-11 CN010 1-784-786-11 CN011 1-784-786-11 CONNECTOR, FFC/FPC 21P PLUG, CONNECTOR 8P PLUG, CONNECTOR 9P CONNECTOR, FFC 25P CONNECTOR, FFC 25P CN5001* 1-564-509-11 PLUG, CONNECTOR 6P CN5002* 1-564-511-11 PLUG, CONNECTOR 8P CN5003* 1-564-505-11 PLUG, CONNECTOR 2P <DIODE> D001 7-12 8-719-062-51 DIODE 1PS226-115 GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. (n) DESCRIPTION REMARK D002 D003 D004 D005 8-719-062-51 8-719-062-51 8-719-062-51 8-719-109-89 DIODE 1PS226-115 DIODE 1PS226-115 DIODE 1PS226-115 ZENER DIODE RD5.6ESB2 D006 D007 D008 D009 D010 8-719-109-89 8-719-109-89 8-719-109-89 8-719-109-89 8-719-109-89 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 D011 D012 D013 D014 D015 8-719-109-89 8-719-109-89 8-719-110-17 8-719-066-11 8-719-066-11 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 ZENER DIODE RD10ESB2 DIODE 1PS184-115 DIODE 1PS184-115 D016 D017 D018 D020 D021 8-719-109-89 8-719-109-89 8-719-109-89 8-719-988-61 8-719-988-61 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 DIODE 1SS355TE-17 DIODE 1SS355TE-17 D022 D023 D024 D025 D026 8-719-066-11 8-719-066-11 8-719-066-11 8-719-062-51 8-719-062-51 DIODE 1PS184-115 DIODE 1PS184-115 DIODE 1PS184-115 DIODE 1PS226-115 DIODE 1PS226-115 D027 D028 D029 D036 D037 8-719-988-61 8-719-988-61 8-719-109-85 8-719-109-89 8-719-109-89 DIODE 1SS355TE-17 DIODE 1SS355TE-17 ZENER DIODE RD5.1ESB2 ZENER DIODE RD5.6ESB2 ZENER DIODE RD5.6ESB2 D038 8-719-045-99 ZENER DIODE RD2.2M-T1B REF.NO. PART NO. IC006 IC010 IC011 IC012 IC5101 1-410-397-21 1-410-397-21 1-410-397-21 1-412-911-11 1-412-911-11 FERRITE FERRITE FERRITE FERRITE FERRITE 1.1µH 1.1µH 1.1µH 1.1µH 1.1µH FB5201 FB5301 FB5303 FB5401 FB5403 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 FERRITE FERRITE FERRITE FERRITE FERRITE 1.1µH 1.1µH 1.1µH 1.1µH 1.1µH FB5601 1-412-911-11 FERRITE 1.1µH REMARK 8-759-700-78 IC NJM082M 8-759-585-70 IC LA7865M-TLM 8-759-442-20 IC 24LC21AT/SN 8-759-442-20 IC 24LC21AT/SN 8-759-822-07 IC LA6515 IC5201 8-759-822-07 IC LA6515 IC5301 8-759-822-07 IC LA6515 IC5401 8-759-822-07 IC LA6515 <COIL> L002 L003 1-406-665-11 COIL, CHOKE 1-406-671-11 COIL, CHOKE 100µH 1mH <TRANSISTOR> Q001 Q002 Q003 Q004 Q005 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 8-729-028-83 TRANSISTOR DTA124EUA-T106 8-729-033-26 TRANSISTOR DTA114GKAT146 Q006 Q007 Q008 Q010 Q011 8-729-027-49 TRANSISTOR DTC123EKA-T146 8-729-901-00 TRANSISTOR DTC124EK 8-729-033-25 TRANSISTOR DTC114GKA 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R Q012 8-729-901-00 TRANSISTOR DTC124EK <RESISTOR> <FERRITE BEAD> FB001 FB002 FB003 FB5101 FB5103 DESCRIPTION <SENSOR> GS5001 1-418-473-11 SENSOR UNIT, GEOMAGNETIC R003 R004 R005 R006 R007 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-057-00 RES-CHIP 100 100 100 100 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R008 R009 R010 R011 R012 1-216-057-00 RES-CHIP 1-216-057-00 RES-CHIP 1-216-057-00 RES-CHIP 1-249-389-11 CARBON 1-216-017-91 RES-CHIP 2.2K 2.2K 2.2K 4.7 47 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/4W F 1/10W R013 R014 R015 R016 R017 1-216-017-91 RES-CHIP 1-216-049-91 RES-CHIP 1-249-389-11 CARBON 1-216-017-91 RES-CHIP 1-216-017-91 RES-CHIP 47 1K 4.7 47 47 5% 5% 5% 5% 5% 1/10W 1/10W 1/4W F 1/10W 1/10W R018 R019 R020 R021 R022 1-216-049-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1K 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R023 R024 R025 R026 R029 1-216-065-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-025-91 RES-CHIP 1-216-073-00 RES-CHIP 4.7K 100 100 100 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W <IC> IC001 IC002 IC003 IC004 IC005 8-759-658-88 8-759-162-80 8-759-527-77 8-759-639-81 8-759-639-81 IC CXD8744Q-0006 IC MM1170BFB IC M24C16-MN6T IC SN74AHCT74PWR IC SN74AHCT74PWR 7-13 GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. (n) REF.NO. PART NO. DESCRIPTION REMARK R030 R031 R032 R034 R035 1-216-049-91 1-216-669-11 1-216-665-11 1-216-049-91 1-216-065-91 RES-CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 1K 5.6K 3.9K 1K 4.7K 5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R036 R037 R039 R040 R042 1-216-659-11 1-216-073-00 1-216-025-91 1-216-025-91 1-216-073-00 METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 2.2K 10K 100 100 10K 0.5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R043 R044 R045 R047 R048 1-216-049-91 1-216-657-11 1-216-049-91 1-216-049-91 1-216-049-91 RES-CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1.8K 1K 1K 1K 5% 0.5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R049 R050 R051 R052 R053 1-216-073-00 1-216-089-91 1-216-077-91 1-216-077-91 1-216-065-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 47K 15K 15K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R054 R055 R056 R057 R058 1-216-077-91 1-216-077-91 1-216-073-00 1-216-073-00 1-216-067-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 15K 15K 10K 10K 5.6K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R059 R060 R061 R062 R063 1-216-057-00 1-216-057-00 1-216-049-91 1-216-613-11 1-216-613-11 RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP 2.2K 2.2K 1K 27 27 5% 5% 5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R064 R066 R067 R075 R076 1-216-613-11 1-216-049-91 1-216-073-00 1-215-407-00 1-215-407-00 METAL CHIP RES-CHIP RES-CHIP METAL METAL 27 1K 10K 270 270 0.5% 5% 5% 1% 1% 1/10W 1/10W 1/10W 1/4W 1/4W R077 R078 R079 R080 R081 1-216-073-00 1-216-121-91 1-216-295-91 1-216-295-91 1-216-049-91 RES-CHIP RES-CHIP SHORT SHORT RES-CHIP 10K 1M 0 0 1K 5% 5% 1/10W 1/10W 5% 1/10W R082 R084 R085 R086 R090 1-216-049-91 1-216-073-00 1-216-049-91 1-216-049-91 1-216-073-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 10K 1K 1K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R091 R092 R093 R094 R095 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R096 R097 R098 R099 R1001 1-216-065-91 1-216-073-00 1-216-073-00 1-216-049-91 1-216-049-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 4.7K 10K 10K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1K 5% 1/10W R1002 1-216-049-91 RES-CHIP REF.NO. PART NO. 7-14 DESCRIPTION REMARK R1003 R1004 R1005 R1006 1-216-049-91 1-216-049-91 1-216-049-91 1-216-049-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1K 1K 1K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R1007 R1008 R1009 R1010 R1011 1-216-049-91 1-216-667-11 1-216-049-91 1-216-049-91 1-216-049-91 RES-CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 1K 4.7K 1K 1K 1K 5% 0.5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1012 R1013 R1014 R1015 R1016 1-216-057-00 1-216-057-00 1-216-049-91 1-216-049-91 1-216-049-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 2.2K 2.2K 1K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1017 R1018 R1019 R1020 R1021 1-216-049-91 1-216-049-91 1-216-049-91 1-216-065-91 1-216-065-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1K 1K 4.7K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1022 R1023 R1024 R1025 R1026 1-216-659-11 1-216-659-11 1-216-681-11 1-216-025-91 1-216-109-00 METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 2.2K 2.2K 18K 100 330K 0.5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1027 R1028 R1029 R1030 R1031 1-216-659-11 1-216-647-11 1-216-025-91 1-216-025-91 1-216-025-91 METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 2.2K 680 100 100 100 0.5% 0.5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1032 R1033 R1034 R1035 R1036 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1037 R1038 R1039 R1040 R1041 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 1-216-025-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1042 R1043 R1044 R1045 R1047 1-216-025-91 1-216-025-91 1-216-667-11 1-216-065-91 1-216-073-00 RES-CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 100 100 4.7K 4.7K 10K 5% 5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1049 R1050 R1051 R1052 R1053 1-216-065-91 1-216-073-00 1-216-097-91 1-216-073-00 1-216-049-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 4.7K 10K 100K 10K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1054 R1055 R1056 R1057 R1058 1-216-073-00 1-216-049-91 1-216-073-00 1-216-049-91 1-216-073-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 1K 10K 1K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1059 1-216-049-91 RES-CHIP R1061 1-216-073-00 RES-CHIP 1K 10K 5% 5% 1/10W 1/10W GDM-5403 The components identified ¡ marked are critical for safety. Replace only with the part number specified. REF.NO. PART NO. (n) DESCRIPTION REMARK R1062 1-216-049-91 RES-CHIP R1063 1-216-065-91 RES-CHIP R1064 1-216-049-91 RES-CHIP 1K 4.7K 1K 5% 5% 5% 1/10W 1/10W 1/10W R1065 R1066 R1067 R1068 R1069 1-216-125-00 1-216-073-00 1-216-057-00 1-216-057-00 1-216-049-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1.5M 10K 2.2K 2.2K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1070 R1071 R5003 R5005 R5006 1-216-057-00 1-216-081-00 1-216-295-91 1-216-081-00 1-216-073-00 RES-CHIP RES-CHIP SHORT RES-CHIP RES-CHIP 2.2K 22K 0 22K 10K 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W R5007 R5010 R5011 R5015 R5108 1-216-049-91 1-216-295-91 1-216-073-00 1-216-049-91 1-216-308-00 RES-CHIP SHORT RES-CHIP RES-CHIP RES-CHIP 1K 0 10K 1K 4.7 5% 1/10W 5% 5% 5% 1/10W 1/10W 1/10W R5109 R5110 R5113 R5115 R5116 1-216-308-00 1-216-073-00 1-216-073-00 1-215-859-00 1-216-073-00 RES-CHIP RES-CHIP RES-CHIP METAL OXIDE RES-CHIP 4.7 10K 10K 22 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1W F 1/10W R5119 R5122 R5205 R5206 R5207 1-216-073-00 1-215-859-00 1-216-073-00 1-215-859-00 1-216-073-00 RES-CHIP METAL OXIDE RES-CHIP METAL OXIDE RES-CHIP 10K 22 10K 22 10K 5% 5% 5% 5% 5% 1/10W 1W F 1/10W 1W F 1/10W R5208 R5209 R5308 R5309 R5310 1-216-069-00 1-216-308-00 1-216-308-00 1-216-308-00 1-216-073-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 6.8K 4.7 4.7 4.7 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R5313 R5315 R5316 R5319 R5322 1-216-073-00 1-215-859-00 1-216-073-00 1-216-073-00 1-215-859-00 RES-CHIP METAL OXIDE RES-CHIP RES-CHIP METAL OXIDE 10K 22 10K 10K 22 5% 5% 5% 5% 5% 1/10W 1W F 1/10W 1/10W 1W F R5406 R5407 R5408 R5409 R5410 1-216-083-00 1-216-085-00 1-216-308-00 1-216-308-00 1-216-081-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 27K 33K 4.7 4.7 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R5413 R5415 R5416 R5419 R5422 1-216-097-91 1-215-887-00 1-216-081-00 1-216-097-91 1-216-451-11 RES-CHIP METAL OXIDE RES-CHIP RES-CHIP METAL OXIDE 100K 150 22K 100K 120 5% 5% 5% 5% 5% 1/10W 2W F 1/10W 1/10W 2W F R5502 R5503 R5504 R5505 R5506 1-216-081-00 1-216-081-00 1-216-089-91 1-216-089-91 1-216-069-00 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 22K 22K 47K 47K 6.8K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1.2 1.2 1.2 5% 5% 5% 1/4W F 1/4W F 1/4W F R5507 1-249-382-11 CARBON R5508 1-249-382-11 CARBON R5509 1-249-382-11 CARBON REF.NO. PART NO. DESCRIPTION REMARK R5510 1-249-382-11 CARBON R5602 1-216-081-00 RES-CHIP 1.2 22K 5% 5% 1/4W F 1/10W R5603 R5604 R5605 R5607 R5610 15K 22K 100K 68 4.7 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1W F 1/10W 1-216-077-91 RES-CHIP 1-216-081-00 RES-CHIP 1-216-097-91 RES-CHIP 1-215-862-11 METAL OXIDE 1-216-308-00 RES-CHIP <CRYSTAL> X001 7-15 1-760-682-21 VIBRATOR, CRYSTAL (24.756MHz) GDM-5403 GDM-5403 9-978-668-01 2000AL05052-1 Sony Corporation 9-978-668-01 Computer Display Company Computer Display DIV. – 78 – English 2000AL05052-1 Printed in Japan 2000. 1