1
Download Service Manual
Transcript
SDM-N50 SERVICE MANUAL US Model Canadian Model AEP Model Chassis No. SCC-L32A-A ST5 CHASSIS SPECIFICATIONS LCD panel Panel type: a-Si TFT Active Matrix Picture size: 15 inch (38 cm) Input signal format RGB operating frequency* Horizontal: 30 – 61 kHz Vertical: 50 – 85 Hz Resolution Horizontal: Max.1024 dots Vertical: Max.768 lines Input signal levels RGB video signal 0.700 Vp-p, 75 Ω, positive SYNC signal TTL level, 2 kΩ, positive or negative (Separate horizontal and vertical, or composite sync) 0.3 Vp-p, 75Ω, negative (Sync on green) Audio output 2W × 2 Headphones jack Stereo minijack Accepts impedance of 16 – 48Ω AUDIO IN jack Stereo minijack Accepts impedance of 16 kΩ Accepts level 0.5 Vrms Power requirements 100 – 240 V, 50 – 60 Hz, 0.55 – 0.3 A Power consumption Max. 35 W Operating temperature 5 – 35 ˚C Dimensions (width/height/depth) Display (upright): Approx. 356 × 347 × 185 mm (14 1/8 × 13 3/4 × 7 3/8 inches) Media engine (without stand): Approx. 45 × 180 × 180 mm (1 13/16 × 7 1/8 × 7 1/8 inches) Media engine (with stand): Approx. 94 × 185 × 180 mm (3 3/4 × 7 3/8 × 7 1/8 inches) Mass Plug & Play Accessories • • • • • • • • • • • • • Display: Approx. 2.7 kg (5 lb 15 oz) Media engine (with stand): Approx. 0.85 kg (1 lb 14 oz) DDC1/DDC2B/DDC2Bi LCD display Media engine Media engine stand Power cord System connecting cable (2 m) (applicable cable type: DP-2) HD15 (RGB) video signal cable Audio cord (stereo miniplug) Macintosh adapter Windows Monitor Information Disk/ Utility Disk Macintosh Utility Disk Warranty card Notes for Macintosh users This instruction manual Recommended horizontal and vertical timing condition • Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. • Horizontal blanking width should be more than 2.3 µsec. • Vertical blanking width should be more than 450 µsec. Design and specifications are subject to change without notice. TFT LCD COLOR COMPUTER DISPLAY MICROFILM SDM-N50 DIAGNOSIS Factorical preservation register LED LED indicates Display part trouble SHUTDOWN_LOG1 bit4 (16) Part of the body only Red (0.5 sec) and Off (0.5 sec) Backlight trouble SHUTDOWN_LOG1 bit2 (4) Parts of the body and the display Amber (0.5 sec) and Off (1.5 sec) Body temperature trouble SHUTDOWN_LOG1 bit3 (8) Parts of the body and the display Amber (1.0 sec) and Off (1.0 sec) 5V voltage anomalous SHUTDOWN_LOG1 bit5 (32) Parts of the body and the display Amber (1.5 sec) and Off (0.5 sec) 3.3V voltage anomalous SHUTDOWN_LOG1 bit6 (64) Parts of the body and the display Amber (1.5 sec) and Off (0.5 sec) *Aging mode ........................................... No input signal and press CONT key for longer than 2 second. Power saving function (user sensor/power saving mode) This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically enter the power saving mode. It automatically enters the low power consumption mode when the user sensor detects the absence of a user. Power consumption state Power consumption AC power indicator 1 (power) indicator normal operation 35 W green green 1 low power consumption mode ≤4W green green and orange alternate 2 power saving mode ≤3W orange orange 1 (power): off ≤3W red off AC power: off 0W off off TIMING SPECIFICATION PRIMARY MODE MODE AT PRODUCTION MODE 0 MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6 MODE 7 640 X 480 640 X 480 640 X 480 640 X 480 720 X 400 720 X 400 720 X 480 720 X 480 25.175 MHz 30.240 MHz 31.500 MHz 36.000 MHz 28.350 MHz 35.500 MHz 35.573 MHz 31.505 MHz 31.469 kHz 35.000 kHz 37.500 kHz 43.269 kHz 31.500 kHz 37.927 kHz 37.683 kHz 35.162 kHz usec usec usec usec usec usec usec usec H. TOTAL 31.778 28.571 26.667 23.111 31.746 26.366 26.537 28.440 H. BLK 6.356 7.407 6.349 5.333 6.349 6.085 6.297 5.586 H. FP 0.636 2.116 0.508 1.556 0.635 1.014 0.450 1.079 H. SYNC 3.813 2.116 2.032 1.556 3.810 2.028 2.024 1.270 H. BP 1.907 3.175 3.810 2.222 1.905 3.042 3.823 3.238 H. ACTIV 25.422 21.164 20.317 17.778 25.397 20.282 20.240 22.854 59.940 Hz 66.667 Hz 75.000 Hz 85.008 Hz 70.156 Hz 85.039 Hz 75.066 Hz 59.901 Hz lines lines lines lines lines lines lines lines V. TOTAL 525 525 500 509 449 446 502 587 V. BLK 45 45 20 29 49 46 22 107 V. FP 10 3 1 1 12 1 2 12 V. SYNC 2 3 3 3 3 3 3 2 V. BP 33 39 16 25 34 42 17 93 V. ACTIV 480 480 480 480 400 400 480 480 RESOLUTION CLOCK — HORIZONTAL — H-FREQ — VERTICAL — V. FREQ(Hz) — SYNC — INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT NO NO NO NO NO NO NO NO YES N/N YES N/N YES N/N YES N/N YES N/P YES N/P YES N/N YES N/N NO NO NO NO NO NO NO NO NON INT NON INT NON INT NON INT NON INT NON INT NON INT NON INT –2– SDM-N50 PRIMARY MODE MODE AT PRODUCTION MODE 8 MODE 9 MODE 10 MODE 11 MODE 12 MODE 13 MODE 14 MODE 15 800 X 600 800 X 600 800 X 600 800 X 600 — — 832 X 624 1024 X 768 36.000 MHz 40.000 MHz 49.500 MHz 56.250 MHz — — 57.285 MHz 65.000 MHz 35.156 kHz 37.879 kHz 46.875 kHz 53.674 kHz — — 46.727 kHz 48.363 kHz usec usec usec usec — — usec usec H. TOTAL 28.444 26.400 21.333 18.631 — — 20.110 20.677 H. BLK 6.222 6.400 5.172 4.409 — — 5.586 4.923 H. FP 0.667 1.000 0.323 0.569 — — 0.559 0.369 H. SYNC 0.889 3.200 1.616 1.138 — — 1.117 2.092 H. BP 4.667 2.200 3.232 2.702 — — 3.910 2.462 H. ACTIV 22.222 20.000 16.162 14.222 — — 14.524 15.754 56.250 Hz 60.317 Hz 75.000 Hz 85.061 Hz — — 74.553 Hz 60.004 Hz lines lines lines lines — — lines lines V. TOTAL 625 628 625 631 — — 667 806 V. BLK 25 28 25 31 — — 43 38 V. FP 1 1 1 1 — — 3 3 V. SYNC 2 4 3 3 — — 3 6 RESOLUTION CLOCK — HORIZONTAL — H-FREQ — VERTICAL — V. FREQ(Hz) V. BP 22 23 21 27 — — 37 29 V. ACTIV 600 600 600 600 — — 624 768 — SYNC — INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT NO NO NO NO — — NO NO YES N/N YES P/P NO P/P YES P/P — — YES N/N YES N/N NO NO NO NO — — NO NO NON INT NON INT NON INT NON INT — — NON INT NON INT PRIMARY MODE MODE AT PRODUCTION MODE 16 MODE 17 MODE 18 MODE 19 MODE 20 MODE 21 MODE 22 MODE 23 RESOLUTION 1024 X 768 1024 X 768 — 1024 X 768 800 X 600 1024 X 768 1024 X 768 848 X 480 CLOCK 75.000 MHz 78.750 MHz — 80.000 MHz 50.000 MHz 71.640 MHz 80.000 MHz 38.336 MHz 56.476 kHz 60.023 kHz — 60.241 kHz 48.077 kHz 53.946 kHz 60.241 kHz 35.300 kHz usec usec — usec usec usec usec usec H. TOTAL 17.707 16.660 — 16.600 20.800 18.537 16.600 28.328 H. BLK 4.053 3.657 — 3.800 4.800 4.243 3.800 6.208 H. FP 0.320 0.203 — 0.400 1.120 0.223 0.400 1.409 H. SYNC 1.813 1.219 — 1.200 2.400 2.457 2.200 3.130 H. BP 1.920 2.235 — 2.200 1.280 1.563 1.200 1.669 H. ACTIV 13.653 13.003 — 12.800 16.000 14.294 12.800 22.120 70.069 Hz 75.029 Hz — 74.927 Hz 72.188 Hz 66.110 Hz 74.927 Hz 59.932 Hz lines lines — lines lines lines lines lines V. TOTAL 806 800 — 804 666 816 804 589 V. BLK 38 32 — 36 66 48 36 109 11 — HORIZONTAL — H-FREQ — VERTICAL — V. FREQ(Hz) V. FP 3 1 — 3 37 8 3 V. SYNC 6 3 — 3 6 4 3 3 V. BP 29 28 — 30 23 36 30 95 V. ACTIV 768 768 — 768 600 768 768 480 — SYNC — INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT NO NO — NO NO NO NO NO YES N/N YES P/P — YES N/N YES N/N YES N/N YES N/N YES N/N NO NO — NO NO NO NO NO NON INT NON INT — NON INT NON INT NON INT NON INT NON INT –3– SDM-N50 PRIMARY MODE MODE AT PRODUCTION MODE 24 MODE 25 MODE 26 MODE 27 MODE 28 MODE 29 MODE 30 MODE 31 RESOLUTION 640 X 400 640 X 350 640 X 400 640 X 480 1024 X 768 640 X 400 720 X 400 800 X 600 25.180 MHz 31.500 MHz 31.500 MHz 31.500 MHz 65.000 MHz 24.870 MHz 28.320 MHz 36.000 MHz 31.475 kHz 37.861 kHz 37.861 kHz 37.861 kHz 48.077 kHz 30.478 kHz 31.467 kHz 35.156 kHz usec usec usec usec usec usec usec usec H. TOTAL 31.771 26.413 26.413 26.413 20.800 32.811 31.780 28.444 H. BLK 6.354 6.095 6.095 6.095 5.046 7.077 6.356 6.222 H. FP 0.953 1.016 1.016 0.762 0.462 0.322 0.636 0.167 H. SYNC 2.542 2.032 2.032 1.270 1.477 3.860 3.814 5.111 H. BP 2.859 3.048 3.048 4.063 3.108 2.895 1.907 0.944 H. ACTIV 25.417 20.317 20.317 20.317 15.754 25.734 25.424 22.222 70.100 Hz 85.080 Hz 85.080 Hz 72.809 Hz 59.797 Hz 59.996 Hz 50.026 Hz 56.160 Hz lines lines lines lines lines lines lines lines V. TOTAL 449 445 445 520 804 508 629 626 V. BLK 49 95 45 40 36 108 229 26 V. FP 11 32 1 9 3 37 102 2 V. SYNC 2 3 3 3 4 2 2 1 V. BP 36 60 41 28 29 69 125 23 V. ACTIV 400 350 400 480 768 400 400 600 CLOCK — HORIZONTAL — H-FREQ — VERTICAL — V. FREQ(Hz) — SYNC — INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT NO NO NO NO NO NO NO NO YES N/N YES P/N YES N/P YES N/N YES N/N YES N/N YES N/N YES N/N NO NO NO NO NO NO NO NO NON INT NON INT NON INT NON INT NON INT NON INT NON INT NON INT PRIMARY MODE MODE AT PRODUCTION MODE 32 MODE 33 MODE 34 MODE 35 MODE 36 RESOLUTION 800 X 600 1024 X 768 1024 X 768 1024 X 768 800 X 600 50.000 MHz 64.000 MHz 65.000 MHz 64.000 MHz 39.530 MHz 48.828 kHz 48.780 kHz 48.363 kHz 48.485 kHz 37.434 kHz usec usec usec usec usec H. TOTAL 20.480 20.500 20.677 20.625 26.714 H. BLK 4.480 4.500 4.923 4.625 6.476 H. FP 0.960 1.000 0.615 1.219 1.012 H. SYNC 1.600 1.500 3.200 1.219 2.530 H. BP 1.920 2.000 1.108 2.188 2.934 H. ACTIV 16.000 16.000 15.754 16.000 20.238 66.888 Hz 59.561 Hz 60.078 Hz 59.637 Hz 59.608 Hz lines lines lines lines lines V. TOTAL 730 819 805 813 628 V. BLK 130 51 37 45 28 V. FP 48 12 3 39 5 V. SYNC 6 6 3 3 1 CLOCK — HORIZONTAL — H-FREQ — VERTICAL — V. FREQ(Hz) V. BP 76 33 31 3 22 V. ACTIV 600 768 768 768 600 — SYNC — INT(G) EXT(H/V)/POLARITY EXT(CS)/POLARITY INT/NON INT YES NO NO NO NO YES N/N YES N/N YES N/N YES N/N YES N/N NO NO NO NO NO NON INT NON INT NON INT NON INT NON INT 2000.1.11 VER. –4– SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7. Check the B+ and HV to see if they are specified values. Make sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV. 8. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC Leakage. Check leakage as described below. To Exposed Metal Parts on Set 0.15 µF 1.5 k Ω AC Voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. SDM-N50 LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOMs that are suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) WARNING!! NEVER TURN ON THE POWER IN A CONDITION IN WHICH THE DEGAUSS COIL HAS BEEN REMOVED. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY SHADING AND MARK ¡ ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE PROCEDURES WHENEVER CRITICAL COMPONENTS ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED. AVERTISSEMENT!! NE JAMAIS METTRE SOUS TENSION QUAND LA BOBINE DE DEMAGNETISATION EST ENLEVÉE. ATTENTION AUX COMPOSANTS RELATIFS À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET UNE MARQUE ¡ SONT CRITIQUES POUR LA SÉCURITÉ. NE LES REMPLACER QUE PAR UNE PIÈCE PORTANT LE NUMÉRO SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT L’IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU FONCTIONNEMENT SONT IDENTIFIÉS DANS LE PRÉSENT MANUEL. SUIVRE CES PROCÉDURES LORS DE CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU LORSQU’UN MAUVAIS FONCTIONNEMENT EST SUSPECTÉ. –5– SDM-N50 TABLE OF CONTENTS Section Title Page 1. GENERAL .................................................................. 1-1 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. U Board Removal ................................................ 2-1 Base Assembly Removal ...................................... 2-1 B Board Removal ................................................ 2-2 H Board Removal ................................................. 2-3 LCD Module (TFT) Removal .............................. 2-3 A Board Removal ................................................. 2-4 G Board Removal ................................................. 2-4 3. ADJUSTMENTS ...................................................... 3-1 4. DIAGRAMS 4-1. 4-2. 4-3. (1) (2) (3) (4) (5) 4-4. Block Diagrams .................................................... 4-1 Circuit Boards Location ...................................... 4-7 Schematic Diagrams and Printed Wiring Boards ... 4-8 Schematic Diagrams of A (P1-P3) Board ............ 4-9 Schematic Diagrams of B (P1-P3) Board ............ 4-23 Schematic Diagrams of H Board .......................... 4-31 Schematic Diagrams of U Board .......................... 4-35 Schematic Diagrams of G (P1-P2) Board ............ 4-43 Semiconductors ................................................... 4-47 5. EXPLODED VIEWS 5-1. 5-2. 5-3. Display ................................................................. 5-1 Chassis ................................................................. 5-2 Packing Materials ................................................ 5-3 6. ELECTRICAL PARTS LIST ............................ 6-1 –6– SECTION 1 GENERAL Precautions Warning on power connections • Use the supplied power cord. If you use a different power cord, be sure that it is compatible with your local power supply. For the customers in the U.S.A. If you do not use the appropriate cord, this monitor will not conform to mandatory FCC standards. For the customers in the UK If you use the monitor in the UK, please use the appropriate UK power cord. Example of plug types for 100 to 120 V AC for 200 to 240 V AC for 240 V AC only Maintenance To adjust the tilt and height To use the display comfortably • Be sure to unplug the power cord from the power outlet before cleaning your monitor. • Clean the LCD screen with a soft cloth. If you use a glass cleaning liquid, do not use any type of cleaner containing an anti-static solution or similar additive as this may scratch the LCD screen’s coating. • Clean the cabinet, panel, and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. • Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver. This type of contact may result in a scratched picture tube. • Note that material deterioration or LCD screen coating degradation may occur if the monitor is exposed to volatile solvents such as insecticide, or if prolonged contact is maintained with rubber or vinyl materials. This display can be adjusted within the angles shown below. This display is designed so that you can set it up at a comfortable viewing angle. Adjust the viewing angle of your display according to the height of the desk and chair, and so that light is not reflected from the screen to your eyes. Transportation The equipment should be installed near an easily accessible outlet. Installation 1-1 Do not install or leave the monitor: • In places subject to extreme temperatures, for example near a radiator, heating vent, or in direct sunlight. Subjecting the monitor to extreme temperatures, such as in an automobile parked in direct sunlight or near a heating vent, could cause deformations of the casing or malfunctions. • In places subject to mechanical vibration or shock. • Near any equipment that generates a strong magnetic field, such as a TV or various other household appliances. • In places subject to inordinate amounts of dust, dirt, or sand, for example near an open window or an outdoor exit. If setting up temporarily in an outdoor environment, be sure to take adequate precautions against airborne dust and dirt. Otherwise irreparable malfunctions could occur. Handling the LCD screen • Do not leave the LCD screen facing the sun as it can damage the LCD screen. Take care when you place the monitor by a window. • Do not push on or scratch the LCD screen. Do not place a heavy object on the LCD screen. This may cause the screen to lose uniformity or cause LCD panel malfunctions. • If the monitor is used in a cold place, a residual image may appear on the screen. This is not a malfunction. The screen returns to normal as the temperature rises to a normal operating level. • If a still picture is displayed for a long time, a residual image may appear for a while. The residual image will eventually disappear. • The LCD panel becomes warm during operation. This is not a malfunction. 4 The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remein as in the manual. • Disconnect all cables from the monitor when transporting. When you transport this display, grasp the support and base sections of the display stand firmly with both hands. Also use both hands when carrying the media engine. If you drop the monitor, you may be injured or the monitor may be damaged. • When you transport this monitor for repair or shipment, use the original carton and packing materials. To enjoy clear sound from the builtin stereo speaker 90˚ 40˚ 50˚ 50˚ To adjust the angles, grasp the lower sides of the LCD panel with both hands as shown below. Tilt the LCD panel adequately backward, then lift the LCD panel upward to the desired screen height, then adjust the screen tilt as desired. When adjusting the screen height and tilt, proceed slowly and carefully, being sure not to hit the LCD panel against the desk or the base of the display stand. This monitor has a built-in stereo speaker in base of the display stand. We recommend that you position the LCD panel slightly away from the display stand. High tones from the speaker may be muffled if the LCD panel is positioned immediately on top of the stand. Be careful not to drop any metal object into the speaker's vents as the speakers generate a magnetic field. Also, this magnetic field may affect data stored on magnetic tapes and discs. Be sure to keep magnetic recording equipment, tapes, and floppy discs away from the speaker’s opening. A duct is provided on the rear part of the display stand to boost the bass. Be sure not to block the duct with paper or other objects to ensure clear sound. US Replacement of the fluorescent tube A specially designed fluorescent tube is installed as the lighting apparatus for this monitor. If the screen becomes dark, unstable, or does not turn on, replace the fluorescent tube with a new one. Consult your Sony dealer when replacing the fluorescent tube. Ducts Disposal of the monitor • Do not dispose of this monitor with general household waste. • The fluorescent tube used in this monitor contains mercury. Disposal of this monitor must be carried out in accordance to the regulations of your local sanitation authority. m Keep the LCD panel slightly away from the base. Speaker 5 Identifying parts and controls See the pages in parentheses for further details. LCD display 6 2 (volume) +/– and M(+)/m(–) buttons (pages 10, 12) These buttons display the VOLUME menu and function as the M(+)/m(–) buttons when selecting the menu items and making adjustments. qg HD15 (RGB) input 2 connector (INPUT2) (page 8) This connector inputs RGB video signals (0.700 Vp-p, positive) and SYNC signals. The pin assignment is the same as qf. Media engine SYSTEM CONNECTER (TO DISPLAY) 7 INPUT and OK button, and indicator (pages 10, 12) This button selects the INPUT 1 or INPUT 2 (HD15 (RGB) connectors) video input signal. The input signal and corresponding input indicator change each time you press this button. This button also functions as the OK button when displaying the menu on the screen. qh AC IN connector (page 9) This connector provides AC power to the monitor. INPUT 1 qj AC power switch (page 9) This switch turns the monitor on and off. When the AC power switch is turned on, the display automatically turns on. AUDIO IN INPUT 2 qk AC power indicator (page 17) This indicator lights up in green when the media engine is turned on. The indicator lights up in red when the display is turned off with the media engine on. The indicator lights up in orange when the monitor is in the power saving mode. MENU 8 Stereo speaker (page 10) This outputs the audio signals as sound. 9 Ducts These are used to boost the bass sound from the speaker. ql Media engine stand This stand is used to install the media engine vertically. INPUT 1 2 OK 0 SYSTEM CONNECTOR (page 8) This connector inputs signals from the media engine when the display and the media engine are connected with a system connecting cable. qa Headphones jack (page 10) This jack outputs audio signals to the headphones. Front Rear qs AUDIO IN jack (page 10) This jack inputs audio signals when connecting to the audio output jack of the computer or other audio equipment. Caution Be sure to install the media engine vertically shown as left. Installing the media engine lying flat may block ventilation, and may cause a malfunction. qd SYSTEM CONNECTOR (TO DISPLAY) (page 8) This connector outputs signals to the display when the display and the media engine are connected with a system connecting cable. US qf HD15 (RGB) input 1 connector (INPUT1) (page 8) This connector inputs RGB video signals (0.700 Vp-p, positive) and SYNC signals. SYSTEM CONNECTER 1-2 5 4 3 2 1 10 9 8 7 6 15 14 13 12 11 1 1 (Power) switch and indicator (pages 9, 17, 22) This switch turns the display on and off. The indicator lights up in green when the monitor is turned on. The indicator flashes in green and orange when the monitor is in low power consumption mode, and lights up in orange when the monitor is in power saving mode. Pin No. Signal 1 Red 2 Green (Sync on Green) 3 Blue 4 ID (Ground) 5 DDC Ground* 6 Red Ground 7 Green Ground 3 MENU button (page 12) This button displays the main menu. 8 Blue Ground 9 DDC + 5V* 4 6 (contrast) button (page 12) This button displays the CONTRAST menu. 10 Ground 11 ID (Ground) 12 Bi-Directional Data (SDA)* 13 H. Sync 14 V. Sync 15 Data Clock (SCL)* 2 Light sensor and user sensor (pages 16, 17, 18) These sensors measure the brightness of the surrounding area and detect when a user becomes present in front of the screen. Be sure not to cover the sensor with papers, etc. 5 8 (brightness) button (page 12) This button displays the BRITGHTNESS menu. * DDC (Display Data Channel) is a standard of VESA. 6 7 x Connecting to a Macintosh or compatible computer Setup With the media engine, display, and computer switched off, first connect the power cord to the media engine, then connect it to a power outlet. Use the supplied Macintosh adapter. Before using your monitor, check that the following accessories are included in your carton: • LCD display • Media engine • Media engine stand • Power cord • System connecting cable (2 m) (applicable cable type: DP-2) • HD15 (RGB) video signal cable • Audio cord (stereo miniplug) • Macintosh adapter • Windows Monitor Information Disk/Utility Disk • Macintosh Utility Disk • Warranty card • Notes for Macintosh users • This instruction manual Step 1: Connect the media engine to your computer Turn off the media engine and computer before connecting. Step 3: Connect the power cord to INPUT1 or INPUT2 connector to AC IN to a power outlet If no picture appears on your screen • Check that the monitor is correctly connected to the computer. • Check that the media engine is on. • If NO INPUT SIGNAL appears on the screen, try changing the input signal (page 10), and confirm that your computer’s graphic board is completely seated in the correct bus slot. • If OUT OF SCAN RANGE appears on the screen, reconnect the old monitor. Then adjust the computer’s graphic board so that the horizontal frequency is between 30 – 61 kHz, and the vertical frequency is between 50 – 85 Hz (only XGA mode at 75 Hz). For more information about the on-screen messages, see “Trouble symptoms and remedies” on page 20. power cord (supplied) Macintosh adapter (supplied)* to video output HD15 (RGB) video signal cable (supplied) Step 4: Turn on the monitor and computer 1 Turn on the media engine. The display automatically turns on. The indicators of the media engine and display light up in green. Macintosh or compatible computer Note Do not touch the pins of the video signal cable connector as this might bend the pins. * Refer to the supplied “Notes for Macintosh users” for further details. x Connecting to an IBM PC/AT or compatible computer Step 2: Connect the display and media engine 1-3 Turn off the display and media engine before connecting. For customers using Windows NT4.0 Monitor setup in Windows NT4.0 is different from Windows 95/98 and does not involve the selection of monitor type. Refer to the Windows NT4.0 instruction manual for further details on adjusting the resolution, refresh rate, and number of colors. 2 Turn on the computer. The installation of your monitor is complete. If necessary, use the monitor’s controls to adjust the picture. to INPUT1 or INPUT2 connector to SYSTEM CONNECTOR of the media engine For customers using Windows 95/98 To maximize the potential of your monitor, install the new model information file from the supplied Windows Monitor Information Disk onto your PC. This monitor complies with the “VESA DDC” Plug & Play standard. If your PC/graphics board complies with DDC, select “Plug & Play Monitor (VESA DDC)” or this monitor’s model name as the monitor type in the “Control Panel” of Windows 95/98. If your PC/graphics board has difficulty communicating with this monitor, load the Windows Monitor Information Disk and select this monitor’s model name as the monitor type. Adjusting the monitor’s resolution and color number Adjust the monitor’s resolution and color number by referring to your computer’s instruction manual. The color number may vary according to your computer or video board. The color palette setting and the actual number of colors are as follows: • High Color (16 bit) t 65,536 colors • True Color (24 bit) t about 16.77 million colors In true color mode (24 bit), speed may be slower. to SYSTEM CONNECTOR of the display to video output IBM PC/AT or compatible computer HD15 (RGB) video signal cable (supplied) system connecting cable (2 m) (supplied) Caution Be sure to install the media engine vertically shown as above. Installing the media engine lying flat may block ventilation, and may cause a malfunction. Note Grasp the plug when connecting the cable. 8 9 US Using the stereo speaker Selecting the input signal You can listen to music, sounds, and other audio files using the stereo speaker of your monitor. Connect the AUDIO IN jack to the audio output jack of your computer or other audio equipment using the supplied audio cord (stereo miniplug). You can connect two computers to this monitor using the INPUT 1 and INPUT 2 connectors. To select one of the two computers, use the INPUT button. Adjusting the volume Press the INPUT button. The input signal and corresponding input indicator, “1” (INPUT 1) or “2” (INPUT 2) change each time you press this button. Volume adjustments are made using a separate VOLUME menu from the main menu (page 11). The VOLUME menu appears on the screen. Before making adjustments 4 V CENTER (page 13) Select the V CENTER menu to adjust the picture’s vertical centering. V CENT ER 25 Connect the monitor and the computer, and turn them on. Wait for at least 30 minutes before making adjustments for the best result. You can make numerous adjustments to your monitor using the on-screen menu. INPUT 1 2 1 Press the 2 +/– buttons. Customizing Your Monitor Navigating the menu OK EX I T 5 ZOOM (page 14) Select the ZOOM menu to adjust the picture’s sharpness according to the input signal’s aspect ratio or resolution. ZOOM ON OF F Press the MENU button to display the main menu on your screen. See page 12 for more information on using the MENU button. VOL UME 40 Notes • You cannot select the input signal when displaying the main menu on the screen. • If no signal is input to the selected connector, NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters the power saving mode. If this happens, select the other connector using the INPUT button. EX I T 6 COLOR (page 14) Select the COLOR menu to adjust the color temperature of the picture. This adjusts the tone of the screen. PHA SE MENU COLOR 9 30 0K 6 5 00K 5 0 0 0K USER L A D J U ST EX I T 2 Press the 2 +/– button to adjust the volume. The menu automatically disappears after about 3 seconds. Using the headphones jack 1-4 You can listen to the audio signals from your computer or other audio equipment using headphones. Connect your headphones to the headphones jack. The speaker turns off when headphones are connected to the headphones jack. Adjust the volume of the headphones using the VOLUME menu. Notes • You cannot adjust the volume when displaying the main menu on the screen. • When your monitor is in low power consumption mode or power saving mode, no sound comes from the speaker. Use the M(+)/m(–) and OK buttons to select one of the following menus. See page 12 for more information on using the M(+)/m(–) and OK buttons. 1 PHASE (page 13) Select the PHASE menu to adjust the phase when the characters or pictures appear fuzzy throughout the entire screen. Adjust the phase after adjusting the pitch. 7 MENU POSITION (page 14) Select the MENU POSITION to change the onscreen menu position. US MEN U POS I T I ON EX I T PHA S E 16 8 RESET (page 15) Select the RESET menu to reset the adjustments. RESE T S CREEN RESE T A L L RESE T EX I T 2 PITCH (page 13) Select the PITCH menu to adjust the pitch when the characters or pictures are unclear in some areas of the screen. EX I T P I TCH 0 EX I T 3 H CENTER (page 13) Select the H CENTER menu to adjust the picture’s horizontal centering. H CENT ER 50 9 Option (page 15) Select m (option) menu to adjust the monitor’s options. The options include: • WIDE STEREO • BASS BOOST • BACKLIGHT • LIGHT SENSOR • POWER SAVE • USER SENSOR • LANGUAGE • MENU LOCK W I D E S T E R EO 1 2 OF F EX I T EX I T (continued) 10 11 x Using the MENU, M(+)/m(–), and OK buttons 1 Display the main menu. Press the MENU button to display the main menu on your screen. MENU Adjusting the contrast (CONTRAST) Contrast adjustment is made using a separate CONTRAST menu from the main menu (page 11). This setting is stored in memory for the signal from the currently selected input connector. 1 Press the 6 (contrast) button. The CONTRAST menu appears on the screen. CONTRAS T 70 2 Select the menu you want to adjust. Press the M(+)/m(–) buttons to display the desired menu. Press the OK button to select the menu item. INPUT , 1 2 OK 4 8 . 4 kHz / Horizontal frequency of the current input signal 6 0Hz Vertical frequency of the current input signal Displaying the current input signal The horizontal and vertical frequencies of the current input signal are displayed in the CONTRAST and BRIGHTNESS menu. 2 Press the M(+)/m(–) buttons to adjust the contrast. 3 Adjust the menu. Press the M(+)/m(–) buttons to make the adjustment. Then press the OK button to return to the previous menu. INPUT , 1 2 OK 1-5 4 Close the menu. Press the MENU button once to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds. The menu automatically disappears after about 3 seconds. Adjusting the black level of an image (BRIGHTNESS) 1 Set the resolution to 1024 × 768 on the computer. 2 Load the Utility Disk. Use the appropriate disk for your computer. For Windows 95/98 Windows Monitor Information Disk/Utility Disk For Macintosh Macintosh Utility Disk 3 Start the Utility Disk and display the test pattern. For Windows 95/98 Click [Utility Disk] t [Windows]/[Utility.exe]. For Macintosh Click [Utility Disk] t [SONY-Utility]. 4 Press the MENU button. 1 Press the 8 (brightness) button. 5 Press the M(+)/m(–) buttons to select The BRIGHTNESS menu appears on the screen. Horizontal frequency of the current input signal and press the OK button. The PITCH menu appears on the screen. becomes uniform. Adjust so that the vertical stripes disappear. 6 0Hz Vertical frequency of the current input signal If the screen is too bright Adjust the backlight. For more information about adjusting the backlight see “Adjusting the backlight” on page 16. 9 Press the M(+)/m(–) buttons until the screen color becomes uniform. Adjust so that the horizontal stripes are at a minimum. 10 Click [END] on the screen to turn off the test pattern. To reset the automatic picture quality adjustment Select SCREEN RESET and activate it using the RESET menu. See page 15 for more information on using the RESET menu. Adjusting the picture position (H CENTER/V CENTER) If the picture is not in the center of the screen, adjust the picture’s centering as follows. These settings may have to be repeated if you change the input signal after reconnecting your computer. 1 Start the Utility Disk and display the test pattern. Repeat steps 2 and 3 of “Eliminating flicker or blurring (PHASE/PITCH).” 3 Press the M(+)/m(–) buttons to select (H CENTER) or (V CENTER) and press the OK button. The H CENTER or V CENTER menu appears on the screen. 4 Move the picture up, down, left, or right until the frame at the perimeter of the test pattern disappears. Press the M(+)/m(–) buttons to adjust the picture’s centering using the H CENTER menu for horizontal adjustment, or the V CENTER menu for vertical adjustment. 5 Click [END] on the screen to turn off the test pattern. 2 Press the M(+)/m(–) buttons to adjust the brightness. (PHASE) and press the OK button. The PHASE menu appears on the screen. The main menu appears on the screen. (PITCH) 6 Press the M(+)/m(–) buttons until the screen color 4 8 . 4 kHz / 8 Press the M(+)/m(–) buttons to select 2 Press the MENU button. The main menu appears on the screen. B R I GHT NESS 50 You can reset the adjustments using the RESET menu. See page 15 for more information on resetting the adjustments. When the monitor receives an input signal, the automatic picture quality adjustment function of this monitor automatically adjusts the picture position, phase, and pitch, and ensures that a clear picture appears on the screen. For more information about this function, see “Automatic picture quality adjustment function” on page 18. For some input signals, this function may not completely adjust the picture position, phase, and pitch. In this case, you can manually set these adjustments according the following instructions. If you manually set these adjustments, they are stored in memory and automatically recalled whenever the monitor receives the same input signals. These settings may have to be repeated if you change the input signal after reconnecting your computer. Brightness adjustment is made using a separate BRIGHTNESS menu from the main menu (page 11). This setting is stored in memory for the signal from the currently selected input connector. MENU x Resetting the adjustments Eliminating flicker or blurring (PHASE/PITCH) 7 Press the OK button. The main menu appears on the screen. If horizontal stripes are observed over the entire screen, adjust the phase as the next step. The menu automatically disappears after about 3 seconds. Note You can adjust neither contrast nor brightness when displaying the main menu on the screen. 12 13 US Displaying a low-resolution signal at the actual resolution (ZOOM) This monitor is preset at the factory to display pictures on the screen in full, irrespective of the picture’s mode or resolution. You can also view the picture at its actual resolution. 4 If necessary, fine tune the color temperature. First press the M(+)/m(–) buttons to select ADJUST and press the OK button. Then press the M(+)/m(–) buttons to select R (Red) or B (Blue) and press the OK button, and then press the M(+)/m(–) buttons to adjust the color temperature. Since this adjustment changes the color temperature by increasing or decreasing the R and B components with respect to G (green), the G component is fixed. 1 Press the MENU button. 2 Press the M(+)/m(–) buttons to select (ZOOM) and press the OK button. The ZOOM menu appears on the screen. R 16 8 G 17 0 B 17 5 3 Press the m(–) button to select OFF. Adjusting the color temperature (COLOR) 1-6 The COLOR settings allow you to adjust the picture’s color temperature by changing the color level of the white color field. Colors appear reddish if the temperature is low, and bluish if the temperature is high. 9300K is generally suitable for word processing and other text oriented applications, and 6500K is generally suitable for video images. You can set the color temperature to 5000K, 6500K, 9300K or user adjustment. 1 Press the MENU button. The main menu appears on the screen. 2 Press the M(+)/m(–) buttons to select (COLOR) and press the OK button. The COLOR menu appears on the screen. 3 Press the M(+)/m(–) buttons to select the desired color temperature. The preset color temperatures are 5000K, 6500K, and 9300K. Since the default setting is 9300K, the whites will change from a bluish hue to a reddish hue as the temperature is lowered to 6500K and 5000K. You can set separate color temperatures for each of the video input signals. 1 Press the MENU button. The main menu appears on the screen. 1 Press the MENU button. Resetting the adjustment data most appropriately for the current input signal If you fine tune the color temperature, the new color setting is stored in memory for USER ADJUSTMENT and automatically recalled whenever USER is selected. The USER ADJUSTMENT setting is common to both the input signals. If you change the user adjustment setting for one input signal, the setting for the other input signal is also changed. Changing the menu’s position (MENU POSITION) To display the picture on the screen in full Select ON in step 3. You can adjust the following options: • WIDE STEREO • BASS BOOST • BACKLIGHT • LIGHT SENSOR • POWER SAVE • USER SENSOR • LANGUAGE • MENU LOCK (RESET) and press the OK button. The RESET menu appears on the screen. Reset the settings according to the following instructions. EX I T The input signal is displayed on the screen at its actual resolution. Additional settings (Option) This monitor has the following two reset methods. Use the RESET menu to reset the adjustments. 2 Press the M(+)/m(–) buttons to select USE R AD J UST MENT The main menu appears on the screen. Resetting the adjustments (RESET) Press the M(+)/m(–) buttons to select SCREEN RESET and press the OK button. The automatic picture quality adjustment function of this monitor automatically adjusts the picture position, phase, and pitch, to the most appropriate value. If this function is activated, the phase is automatically adjusted whenever the monitor receives the same input signal. The RESET menu is automatically returned to the main menu after the adjustment data is reset. Resetting all of the adjustment data for all input signals You can change the menu position if it is blocking an image on the screen. Press the M(+)/m(–) buttons to select ALL RESET and press the OK button. The RESET menu is automatically returned to the main menu after the adjustment data is reset. 1 Press the MENU button. To cancel resetting The main menu appears on the screen. 2 Press the M(+)/m(–) buttons to select (MENU POSITION) and press the OK button. The MENU POSITION menu appears on the screen. 3 Press the M(+)/m(–) buttons to select the desired position. There are three positions each for the top of the screen and the bottom of the screen, and one for the screen center. Press the M(+)/m(–) buttons to select and press the OK button. The RESET menu returns to the main menu without resetting the adjustment data. The main menu appears on the screen. 2 Press the M(+)/m(–) buttons to select m. The option menu appears on the screen. 3 Press the M(+)/m(–) buttons to select the desired option item and press the OK button. Adjust the selected option item according to the following instructions. Increasing the soundscape (wide stereo function) This adjustment makes use of the DSP and creates the illusion of the built-in stereo speaker being further away than it actually is, thus enhancing sound presence. First press the M(+)/m(–) buttons to select (WIDE STEREO) and press the OK button. Then press the M(+)/m(–) buttons to select either 2, 1, or OFF. The wide stereo function is used to increase the soundscape. Selecting 1 or 2 increases incrementally the soundscape effect toward the front of the monitor. Notes • If your connected computer or audio equipment uses special sound functions, such as surround sound, be sure to turn these functions off. If these functions are being used with the wide stereo function of this monitor, the wide stereo function may not function properly and thus not produce the desired sound effect. • This function is automatically turned off when you use headphones. However, in this case, the indication in the WIDE STEREO menu does not change. • The wide stereo function allows you to increase the soundscape by converting the analog signals into digital. The sound may be distorted depending on the input signal and music. In this case, decrease the volume or set the wide stereo function to OFF. Boosting the bass (bass boost function) This option increases the bass output of the speaker. First press the M(+)/m(–) buttons to select (BASS BOOST) and press the OK button. Then press the M(+)/m(–) buttons to select either ON or OFF. (continued) 14 15 US Adjusting the backlight Selecting the on-screen menu language If the screen is too bright, adjust the backlight. First press the M(+)/m(–) buttons to select (BACKLIGHT) and press the OK button. Then press the M(+)/m(–) buttons to adjust the desired light level. English, German, French, Spanish, Italian and Japanese versions of the on-screen menus are available. The default setting is English. First press the M(+)/m(–) buttons to select (LANGUAGE) and press the OK button. Then press the M(+)/m(–) button to select a language. • ENGLISH • DEUTSCH: German • FRANÇAIS: French • ESPAÑOL: Spanish • ITALIANO: Italian • : Japanese Automatically adjusting the screen brightness (light sensor) This monitor is provided with a sensor to detect the brightness of the surrounding area (light sensor). This sensor is used to automatically adjust the brightness of the screen. First press the M(+)/m(–) buttons to select (LIGHT SENSOR) and press the OK button. Then press the M(+)/m(–) buttons to select either ON or OFF. When you select ON, the monitor automatically adjusts the screen brightness according to the brightness of the surroundings. For more information about this function, see “Automatic brightness adjustment function (light sensor)” on page 18. Note If this function is set to ON, the value of the BACKLIGHT menu does not change. If the screen brightness is still not appropriate after the automatic adjustment, you can manually adjust the backlight. After the backlight adjustment is made, the monitor automatically adjusts the screen brightness in accordance with the new backlight value. Setting up the power saving mode This monitor has a function which enables it to enter the power save mode automatically according to the power saving settings of the computer. You can prevent the monitor from entering the power saving mode by setting the following option to OFF. First press the M(+)/m(–) buttons to select ZZ... (POWER SAVE) and press the OK button. Then press the M(+)/m(–) buttons to select either ON or OFF. 1-7 Using the user sensor The user sensor function enables the monitor to enter the low power consumption mode when no one is present in front of the monitor. First press the M(+)/m(–) buttons to select (USER SENSOR) and press the OK button. Then press the M(+)/m(–) buttons to select either ON or OFF. If you select ON, the monitor automatically enters the low power consumption mode when you move away from the front of the monitor. For more information about the low power consumption mode, see “Power saving function (user sensor/power saving mode)” on page 17. 16 Locking the menus and controls You can protect adjustment data by locking the menus and controls. First press the M(+)/m(–) buttons to select (MENU LOCK) and press the OK button. Then press the M(+)/m(–) buttons and select ON. Only the 1 (power) switch, and (MENU LOCK) of the option menu will operate. If any other items are selected, the mark appears on the screen. To cancel the menu lock Repeat the procedure above and set and (MENU LOCK) to OFF. Technical Features Power saving function (user sensor/power saving mode) This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically enter the power saving mode. It automatically enters the low power consumption mode when the user sensor detects the absence of a user. 1 (power) indicator Power consumption state Power consumption AC power indicator normal operation 35 W green green 1 low power consumption mode ≤4W green green and orange alternate 2 power saving mode ≤3W orange orange 1 (power): off ≤3W red off AC power: off 0W off off 1 Low power consumption mode (user sensor) 2 Power saving mode When the user sensor in the monitor detects the absence of a user, the monitor enters low power consumption mode after about 20 seconds. In low power consumption mode, the monitor is in a power saving state and shuts off power to all circuitry (except for that of the sensors) regardless of the setting of the computer. The monitor returns to normal operation mode when the presence of a user is detected by the user sensor. When the monitor enters the power saving mode (as set according to the computer’s settings), the power saving mode takes precedence over the low power consumption mode. In this case, the monitor stays in the power saving mode regardless of the presence or absence of a user. To return the monitor to normal operation mode, reset the computer’s power saving mode. DPMS defines three power saving states according to the state of the sync signals supplied from the computer. This monitor’s power consumption is input at approximately 3 W in all of these states if the power saving function is set to ON. When your computer enters in the power saving mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. After a few seconds, the monitor enters power saving mode. Note The user sensor detects the presence/absence of a user up to a distance of approximately 60 cm from the screen surface. However, this distance may vary depending on the user’s clothes or the brightness of the surrounding area. If user detection fails due to the ambient conditions of the surrounding area, set the user sensor to OFF. If your monitor does not automatically return from low power consumption mode due to the failure of the user sensor to detect the presence of a user, press the 1 (power) switch twice to turn the monitor off and then on. Power saving state Sync signal state suspend (sleep)* horizontal: on / vertical: off standby (sleep)* horizontal: off / vertical: on active off (deep sleep)* horizontal: off / vertical: on * “Sleep” and “deep sleep” are power saving modes defined by the Environmental Protection Agency. Note The power saving function may not work normally if sync signals other than those listed above are supplied. In such a case, set the power saving function to OFF. 17 US Automatic brightness adjustment function (light sensor) This monitor is provided with a feature to automatically adjust the screen brightness according to the brightness of the surroundings. The brightness of the backlight is set to the most appropriate level by setting the light sensor to ON. The default setting of the brightness of the backlight is set to its maximum. When the light sensor setting is set to ON, the monitor adjusts the brightness of the backlight linearly from its lower- to upper-limit values. When the user adjusts the backlight, the backlight brightness is automatically adjusted between the user adjustment value and the upper- and lower-limit values. Backlight brightness Automatic brightness adjustment after user adjustment If CABLE DISCONNECTED appears on the screen Troubleshooting This indicates that the video signal cable has been disconnected from the currently selected connector. Before contacting technical support, refer to this section. I NFORMA T I ON On-screen messages CAB L E D I SCONNECT ED I NPUT : 1 GO TO POWER SAVE If there is something wrong with the input signal, one of the following messages appears on the screen. To solve the problem, see “Trouble symptoms and remedies” on page 20. Maximum If OUT OF SCAN RANGE appears on the screen This indicates that the input signal is not supported by the monitor’s specifications. Check the following items. User adjustment value Preset automatic adjustment I NFORMA T I ON OUT OF SCAN RANGE Minimum x x . x kHz / Brightness during user adjustment Brightness of surroundings User-specified brightness value Automatic picture quality adjustment function 1-8 When the monitor receives an input signal, it automatically matches the signal to one of the factory preset modes stored in the monitor’s memory to provide a high quality picture at the center of the screen. (See Appendix for a list of the factory preset modes.) For input signals that do not match one of the factory preset modes, the automatic picture quality adjustment function of this monitor automatically adjusts the picture position, phase, and pitch, and ensures that a clear picture appears on the screen for any timing within the monitor’s frequency range (horizontal: 30 – 61 kHz, vertical: 50 – 85 Hz). Consequently, the first time the monitor receives input signals that do not match one of the factory preset modes, the monitor may take a longer time than normal for displaying the picture on the screen. This adjustment data is automatically stored in memory so that next time, the monitor will function in the same way as when the monitor receives the signals that match one of the factory preset modes. In all modes as above, if the picture is adjusted, the adjustment data is stored as a user mode and automatically recalled whenever the same input signal is received. Note While the automatic picture quality adjustment function is activated, only the 1 (power) switch, and INPUT button will operate. INPUT: This indicates the currently selected connector (INPUT: 1 or INPUT: 2). GO TO POWER SAVE The monitor will enter the power saving mode after about 4 seconds from the message is displayed. x xHz If “xx.x kHz/xx Hz” is displayed This indicates that either the horizontal or vertical frequency is not supported by the monitor’s specifications. The figures indicate the horizontal and vertical frequencies of the current input signal. The horizontal frequencies above 100 kHz and the vertical frequencies above 100 Hz are represented by 99.9 kHz and 99 Hz, respectively. US If “RESOLUTION > XGA” is displayed This indicates that the resolution is not supported by the monitor’s specifications. If NO INPUT SIGNAL appears on the screen This indicates that no signal is input, or that no signal is input from the currently selected connector. I NFORMA T I ON NO I NPUT S I GNA L I NPUT : 1 GO TO POWER SAVE INPUT: This indicates the currently selected connector (INPUT: 1 or INPUT: 2). GO TO POWER SAVE The monitor will enter the power saving mode after about 4 seconds from the message is displayed. Note on the adjusting the phase If the automatic picture quality adjustment function is activated, the picture moves slightly whenever the monitor receives the input signal, regardless of the stored adjustment. 18 19 Trouble symptoms and remedies If a problem is caused by the connected computer or other equipment, please refer to the connected equipment’s instruction manual. Use the self-diagnosis function (page 22) if the following recommendations do not resolve the problem. Symptom Symptom Check these items Picture flickers, bounces, oscillates, or is scrambled • Adjust the pitch and phase (page 13). • Isolate and eliminate any potential sources of electric or magnetic fields such as other monitors, laser printers, electric fans, fluorescent lighting, or televisions. • Move the monitor away from power lines or place a magnetic shield near the monitor. • Try plugging the monitor into a different AC outlet, preferably on a different circuit. Check these items xProblems caused by the connected computer or other equipment • Check your graphics board manual for the proper monitor setting. • Confirm that the graphics mode (VESA, Macintosh 19" Color, etc.) and the frequency of the input signal are supported by this monitor (Appendix). Even if the frequency is within the proper range, some video boards may have a sync pulse that is too narrow for the monitor to sync correctly. • Adjust the computer’s refresh rate (vertical frequency) to obtain the best possible picture. No picture If the AC power indicator is not lit • Check that the power cord is properly connected. If the AC power indicator is red • Check that the 1 (power) switch is in the “on” position. If the 1 (power) indicator is not lit, or if the 1 (power) indicator will not light up when the 1 (power) switch is pressed • Check that the 1 (power) switch is in the “on” position. • Check that the AC power switch is in the “on” position. • Check that the system connecting cable is properly connected and all plugs are firmly seated in their sockets (page 8). If the 1 (power) indicator is green or flashing orange • Use the self-diagnostics function (page 22). If the 1 (power) indicator is alternating between green and orange • The monitor cannot return from low power consumption mode because the user sensor fails to detect the presence of a user. Press the 1 (power) switch twice to turn the monitor off and then on. If you set the user sensor to OFF, the monitor does not enter low power consumption mode (page 16). If CABLE DISCONNECTED appears on the screen, or the AC power indicator is flashing red • Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets (page 8). • Check that the video input connector’s pins are not bent or pushed in. • A non-supplied video signal cable is connected. If you connect a non-supplied video signal cable, CABLE DISCONNECTED appears on the screen before entering the power saving mode. This is not a malfunction. • Check that the system connecting cable is properly connected and all plugs are firmly seated in their sockets (page 8). • Press the AC power switch twice to turn the monitor off and then on. 1-9 If NO INPUT SIGNAL appears on the screen, or the 1 (power) indicator is orange • Check that the video signal cable is properly connected and all plugs are firmly seated in their sockets (page 8). • Check that the input select setting is correct (page 10). • Check that the video input connector’s pins are not bent or pushed in. xProblems caused by the connected computer or other equipment • The computer is in the power saving mode. Try pressing any key on the keyboard or moving the mouse. • Check that the computer’s power is “on.” • Check that the graphic board is completely seated in the proper bus slot. If OUT OF SCAN RANGE appears on the screen xProblems caused by the connected computer or other equipment • Check that the video frequency range is within that specified for the monitor. If you replaced an old monitor with this monitor, reconnect the old monitor and adjust the frequency range to the following: Horizontal: 30 – 61 kHz Vertical frequency: 50 – 85 Hz (only XGA mode at 75 Hz) If using Windows 95/98 • If you replaced an old monitor with this monitor, reconnect the old monitor and do the following. Install the Windows Monitor Information Disk (page 9) and select this monitor (“SDM-N50”) from among the Sony monitors in the Windows 95/98 monitor selection screen. If using a Macintosh system • Check and refer to the supplied “Notes for Macintosh users.” Picture is fuzzy • Adjust the brightness and contrast (page 12). • Adjust the pitch and phase (page 13). Picture is ghosting • Eliminate the use of video cable extensions and/or video switch boxes. • Check that all plugs are firmly seated in their sockets. Picture is not centered or sized properly • Adjust the pitch and phase (page 13). • Adjust the picture position (page 13). Note that some video modes do not fill the screen to the edges. The picture is too small • Set the zoom setting to ON (page 14). xProblems caused by the connected computer or other equipment • Set the computer’s resolution to the screen’s resolution. Wavy or elliptical pattern (moire) is visible • Adjust the pitch and phase (page 13). Color is not uniform • Adjust the pitch and phase (page 13). White does not look white • Adjust the color temperature (page 14). Monitor buttons do not operate ( appears on the screen) • If the menu lock is set to ON, set it to OFF (page 16). The monitor turns off after a while • Set the power saving function to OFF (page 16). • Set the user sensor to OFF (page 16). US xProblems caused by the connected computer or other equipment • Set the computer’s power saving setting to off. Displaying this monitor’s name, serial number, and date of manufacture. While the monitor is receiving a video signal, press and hold the MENU button for more than 5 seconds to display this monitor’s information box. If any problem persists, call your authorized Sony dealer and give the following information: • Model name: SDM-N50 • Serial number • Name and specifications of your computer and graphics board. MENU Example INFORMATION MODEL : SDM-N50 SER NO : 1234567 MANUFACTURED : 1999-52 Model name Serial number Week and year of manufacture 20 21 Self-diagnosis function Specifications This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer(s), the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard or moving the mouse. 1 (power) indicator If the 1 (power) indicator is green 1 Turn off the AC power switch and disconnect the video signal cables from the INPUT1 and INPUT2 connectors of the media engine. 2 Press the AC power switch twice to turn the monitor off and then on. 1-10 If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cables and check the condition of your computer(s). If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor’s condition. If the 1 (power) indicator is flashing orange Press the 1 (power) switch twice to turn the monitor off and then on. If the 1 (power) indicator lights up green, the monitor is working properly. If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and graphic board. 22 LCD panel Panel type: a-Si TFT Active Matrix Picture size: 15 inch (38 cm) RGB operating frequency* Horizontal: 30 – 61 kHz Vertical: 50 – 85 Hz Resolution Horizontal: Max.1024 dots Vertical: Max.768 lines Input signal levels RGB video signal 0.700 Vp-p, 75 Ω, positive SYNC signal TTL level, 2 kΩ, positive or negative (Separate horizontal and vertical, or composite sync) 0.3 Vp-p, 75Ω, negative (Sync on green) Audio output 2W × 2 Headphones jack Stereo minijack Accepts impedance of 16 – 48Ω AUDIO IN jack Stereo minijack Accepts impedance of 16 kΩ Accepts level 0.5 Vrms Power requirements 100 – 240 V, 50 – 60 Hz, 0.55 – 0.3 A Power consumption Max. 35 W Operating temperature 5 – 35 ˚C Dimensions (width/height/depth) Display (upright): Approx. 356 × 347 × 185 mm (14 1/8 × 13 3/4 × 7 3/8 inches) Media engine (without stand): Approx. 45 × 180 × 180 mm (1 13/16 × 7 1/8 × 7 1/8 inches) Media engine (with stand): Approx. 94 × 185 × 180 mm (3 3/4 × 7 3/8 × 7 1/8 inches) Mass Display: Approx. 2.7 kg (5 lb 15 oz) Media engine (with stand): Approx. 0.85 kg (1 lb 14 oz) Plug & Play DDC1/DDC2B/DDC2Bi Accessories See page 8. Input signal format * Recommended horizontal and vertical timing condition • Horizontal sync width duty should be more than 4.8% of total horizontal time or 0.8 µs, whichever is larger. • Horizontal blanking width should be more than 2.3 µsec. • Vertical blanking width should be more than 450 µsec. Design and specifications are subject to change without notice. SDM-N50 SECTION 2 DISASSEMBLY 2-1. U BOARD REMOVAL 1 Open these hinge covers (F) and (R) by the – screw driver and so on. * When open the hinge cover (R), these claws in figure would be break so replace new parts. Hinge cover (F) Hinge cover (R) Claws Shield case U 6 Remove the U board in the direction of allow. 5 Three screws (+BVTP 3 x 8) 2 Two screws (+PS 4 x 6) Cushion CN404 CN406 CN405 CN402 4 Base 3 Five screws (+KTP 3 x 14) 2-2. BASE ASSEMBLY REMOVAL * Remove the U board refering 2-1. 2 Two screws 1 Two screws (+P 3 x 5) (+P 3 x 5) 4 Base assembly CN406 CN402 Cushion LCD module (TFT) 2-1 3 Base hinge SDM-N50 2-3. B BOARD REMOVAL 1 Three screws 2 Remove the rear cover after move it in (Tapping screw 3 x 8) the direction of allow A and also remove concavities. Four concavities 4 Shield case (B) 3 Three screws A (0 plate special head) 9 Screw (0 plate special head) 8 BH1 harness assembly CN508 CN502 CN501 CN507 5 Two screws (+P 2 x 4) 6 Cable holder (B) 10 B board CN504 7 Cable holder (A) Four claws Cushion LCD module (TFT) 2-2 SDM-N50 2-4. H BOARD REMOVAL 5 Cover holder 1 Three screws (+BVTP 3 x 6) 2 Earth (H) 2 Earth (H) 3 H board CN501 LCD module (TFT) 4 BH1 harness assembly Cushion 2-5. LCD MODULE (TFT) REMOVAL * Remove the B and H boards refering 2-3 and 2-4. 1 Remove the LCD module (TFT) in the direcition of allow A horizontally. A Cushion Front cover assembly 2-3 SDM-N50 2-6. A BOARD REMOVAL 3 Four screws (HD 15) CN705 CN701 5 Three connectors CN702 (CN705, CN701, CN702) 4 Three screws (+P 3 x 5) 1 Four screws (+BVTP 3 x 12) 6 A board 2 Case (L) 2-7. G BOARD REMOVAL * Remove A board refering 2-6. 5 Remove the terminal board assembly 4 Remove the case in the in the direction of allow b . direction of allow a . 1 Four screws 6 Remove the G board in the direction of allow C . (+P 3 x 5) b CN703 c a CN704 2 Two earth wires 3 Two connectors (CN703, CN704) Chassis plate assembly 2-4 SECTION 3 SDM-N50 ADJUSTMENTS Connect the personal computer, monitor, and signal generator as shown below, and control the monitor. Signal generator (VG-823, etc.) TO INPUT-1 Computer for jig TO CN107 CONNECTOR (A Board) * Maintain the Aging mode for over 30 minutes. • Preset mode adjustment (7) Perform color save ( select C with ALT+M ). Spec: 9300°K 80IRE (x, y) = (0.285, 0.294) Within 3JND 9300°K 30IRE (x, y) = (0.265, 0.268) Within 4JND Note: Make adjustment up to ±0.002. Confirm the screen by below three kinds of the modes within preseted frequency. Signal mode 1. MODE 0 (640X480 60Hz) 2. MODE 10 (800X600 75Hz) 3. MODE 17 (1024X768 75Hz) (1) Input a cross hatch signal. (2) Confirm both edges can see or white lines of edges are not separating from indicated area edges. Errors in the range of 2dot are permit. Be saticefy one of both edges that is within above specification. 2. Adjustment of 6500°K (1) Confirm every R/G/B_USER_BKG are initialized value. (2) Receive MODE 15 (1024X768 60Hz) 80IRE. Set COLOR to 6500°K. (COLOR_INDEX=2) (3) Make adjustment with R/G_USR_DRV to set the chromaticity within the specification. y adjustment ..... Make adjustment with B_USR_DRV. (Also x value changes simultaneous) B_USR_DRV UP Values x and y decrease. B_USR_DRV DOWN Values x and y increase. x adjustment ..... Make adjustment with R_USR_DRV. R_USR_DRV UP Value y increases. R_USR_DRV DOWN Value y decreases. Adjust again and bring down G_USR_DRV 10 STEP to become within the specification ; however, in case of adjustment range of y value become deficientlly and when B_USR_DRV=255. (4) Make the signal 30IRE all white to check that it is within the specification. (5) Adjust R/B_USER_BKG to become within the specification when (4) deviates the specification. (6) Input a grayscale and perform picture quality confirmation. (7) Perform color save ( select C with ALT+M ). Spec: 6500°K 80IRE (x, y) = (0.314, 0.324) Within 3JND 6500°K 30IRE (x, y) = (0.295, 0.305) Within 4JND Note: Make adjustment up to ±0.002. • White balance adjustment 1. (1) (2) (3) (4) (5) (6) When no measuring instrument is used, compare the color with the reference set so that the colors will be the same. Adjustment of 9300°K Confirm every R/G/B_USER_BKG are initialized value. Receive MODE 15 (1024X768 60Hz) 80IRE. Set COLOR to 9300°K. (COLOR_INDEX=1) Make adjustment with R/G_USR_DRV to set the chromaticity within the specification. y adjustment ..... Make adjustment with B_USR_DRV. (Also x value changes simultaneous) B_USR_DRV UP Values x and y decrease. B_USR_DRV DOWN Values x and y increase. x adjustment ..... Make adjustment with R_USR_DRV. R_USR_DRV UP Value y increases. R_USR_DRV DOWN Value y decreases. Adjust again and bring down G_USR_DRV 10 STEP to become within the specification ; however, in case of adjustment range of y value become deficientlly and when B_USR_DRV=255. Make the signal 30IRE all white to check that it is within the specification. Adjust R/B_USER_BKG to become within the specification when (4) deviates the specification. Input a grayscale and perform picture quality confirmation. 3-1 SDM-N50 3. Adjustment of 5000°K (1) Confirm every R/G/B_USER_BKG are initialized value. (2) Receive MODE 15 (1024X768 60Hz) 80IRE. Set COLOR to 5000°K. (COLOR_INDEX=3) (3) Make adjustment with R/G_USR_DRV to set the chromaticity within the specification. y adjustment ..... Make adjustment with B_USR_DRV. (Also x value changes simultaneous) B_USR_DRV UP Values x and y decrease. B_USR_DRV DOWN Values x and y increase. x adjustment ..... Make adjustment with R_USR_DRV. R_USR_DRV UP Value y increases. R_USR_DRV DOWN Value y decreases. Adjust again and bring down G_USR_DRV 10 STEP to become within the specification ; however, in case of adjustment range of y value become deficientlly and when B_USR_DRV=255. (4) Make the signal 30IRE all white to check that it is within the specification. (5) Adjust R/B_USER_BKG to become within the specification when (4) deviates the specification. (6) Input a grayscale and perform picture quality confirmation. (7) Perform color save ( select C with ALT+M ). Spec: 5000°K 80IRE (x, y) = (0.345, 0.352) Within 3JND 5000°K 30IRE (x, y) = (0.322, 0.332) Within 4JND Note: Make adjustment up to ±0.002.position. 3-2 SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAMS A( RGB PROCESS, SCAN CONVERTER, GV IF TRANSMITTER SYSTEM CONTROL 1 RED1 2 GREEN1 3 BLUE1 13 HS1 14 VS1 12 DDC1 SDA 15 DDC1 SCL D RA0 112 OUT(R) 35 7 R IN 5 IN1(G) OUT(G) 30 15 G IN 7 IN1(B) OUT(B) 27 22 B IN 16 IN2(B) 2 GREEN2 3 BLUE2 13 HS2 14 VS2 12 DDC2 SDA 15 DDC2 SCL 52 . 50 . LCD R5 49 21 GA D0 G 14 GA D7 D BA0 65 29 BA D0 B CN101 18 S DATA P 30 R5 26 S DATA N 31 FL303 22 BA D7 15 . G0 14 . 11 LCD G0 46 . 45 . 43 236 CAP CLK1 HS OUT 117 240 AH SYNC S COAST 41 OUT(SOG) 25 23 R0 LCD R0 55 RA D7 D GA7 85 D BA7 72 DATA CK 115 13 IN2(G) LCD G5 40 8 G5 LCD B0 36 5 H SYNC 40 SUB SCL SUB SDA CLAMP 28 SW 19 B0 SDA 29 REF CLK LCD B5 31 167 PDE 86 40 DE 168 PSHIFT CLK 90 169 PH SYNC 87 42 H SYNC 170 PV SYNC 88 43 V SYNC 164 REF CLK CH3 AD0 IC216 3.3V REC VS1 13 6A 1 1A HS1 6Y 12 VS1 1Y 2 2 1A 12 4A AD3 1 VCC 5V 1Y 3 11 5A 5Y 10 1G 1 13 6A 6Y 12 4Y 11 9 4A 4Y 8 OUT 3 A 3.3V HS AD4 HS AD5 VS AD6 11 5A 5Y 10 3 2A 2Y 4 HS2 2Y 6 5 2A 2G 4 VS2 VS2 12 4A 3Y 1 12 DQ7 2 3 4 2 SDDT0 - 7 181 RESET 182 MC RD 8 DQ0 SD DATA(0) 114 180 MC WR /RD 9 3A 4Y 8 SDT P SDT GND SDT N GND SCL SDA CPU ST CN SENS AUDIO L AUDIO GND AUDIO R B TO U BOARD CN401 STBY 5V 12V 12V 12V GND GND GND AUDIO 12V AUDIO 12V CN106 179 MC INT CH3 RST 13 4G 9 4A IC303 SD RAM 178 MC ALE /WRL 3G 10 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 175 MC AD(8) ALE 4Y 11 12V SW Q301,303 174 CH3 INT1 3Y 8 9 3A 41 SFT CLK 172 A8 IC215 BUFF CE 26 171 AD7 4G 13 HS2 5V SW Q302 166 MC AD(0) CH3 AD1 AD2 IC209(1/2) INVERTER IC207 SYNC SELECT IC208 INVERTER HS1 STBY +5V 2. 47 . 46 B5 SCL 30 DDC2 V CLK INPUT 2 RED2 6 D GA0 92 IC304 GV IF TRANSMITTER 13 RA D0 R D RA7 105 11 IN2(R) CN103 1 IC301 SCAN CONVERTER IC214 A/D CONVERT 2 IN1(R) DDC1 V CLK INPUT 1 ) IC205 VIDEO SW CN102 SD DATA(7) 122 AUDIO R AUDIO GND AUDIO L AUDIO GND 240 AH SYNC S 10 3G SD DATA(8) 123 236 CAP CLK1 39 DQ8 C TO G BOARD CN705 SDDT8 - 15 2Y 6 5 2A 4 2G SDA12 18 CS SDA11 SOG 3 VIDEO 2 C/H SYNC IC210(2/2) HS 12 BUFF Q201 H DRV 13 11 H 13 5 V V DRV 11 V SYNC 1 3 H 4 EXIV 15 MEM CLK OUT 112 CAS 16 SDA11 SDA10 20 A10/AP RAS 17 WE 15 LD QM 14 21 A0 LCD QM 36 SDA0 - 9 CLK 35 32 A9 6 5 2 SDDQM 109 18 CS 19 BVA 1 1G IC203 1 SDA12 234 AV SYNC SD CAS 1 2 3 4 5 6 7 8 SD WE SD RAS SDD QM MEM CLK OUT 12V 12V 12V 12V GND GND GND GND D TO G BOARD CN701 IC302 SD RAM SD RAS 108 1Y 2 2 1A IC209(2/2) INEXIH 17 VS 6 4 2G 2 POLH 18 2Y CLK 35 32 A9 SDWE 107 5 2A IC210(1/2) WDQM 36 SD CAS 106 233 AH SYNC R 13 4G VS SDA0 - 9 SDADDR(12) 103 HS 4Y 11 12 4A RAS 17 LDQM 14 21 A0 SDAD0 - 12 IC211 BUFF WE 15 20 AIO/AP SDADDR(0) 92 CLAMP 12 CAS 16 19 BA SDA10 IC206 SYNC DETECTOR CN105 49 DQ15 SD DATA(15) 131 SD DATA(16) 132 SD CAS SD WE SD RAS SDD QM MEM CLK OUT DQ0 2 SDDT16 - 23 INPOLV 16 SD DATA(23) 140 12 DQ7 SD DATA(24) 142 39 DQ8 IC212 2OE 7 5 2A SCL CN104 SDA 3.3V 49 DQ15 2 1A 3 1B X301 1OE 1 PANEL CLK 161 OUT 5V IC103 EEP ROM CH3 AD0,CH3 AD1 SDA 5 AD2 AD3 AD4 AD5 AD6 A8 AD7 ALE /RD SCL 6 REF CLK D101 POWER /WRL IC108 SW WC 7 CH3 INT1 5V(STBY) 4 CH3 RST SW Q102,103 SD DATA(31) 149 IC109 1 2 9 IN3 OUT3 8 10 IN4 OUT4 11 CH3 AD1 2 IN1 OUT1 1 CH3 AD0 V CLK 7 SDA 5 SCL 6 SCL WC CLK SDA 93 92 91 90 89 88 87 86 85 17 AD00 LED GREEN 9 ALE LED UMBER 10 29 12 48 AD08 SER11 SER12 75 DD ON 64 63 59 IRQ1 1 WRLX 2 PA3 3 RDX 7 VS 8 VS 21 22 HS 53 IRQ2 POL H POL V IC106 EEP ROM 72 INPUT SEL C1 13 69 70 68 67 EXIT V TO G BOARD CN702 9 8 7 6 5 4 3 2 1 EXIT H A 3.3V 3.3V GND GND 5V(STBY) 5V(STBY) GND GND DD ON SDDT24 - 31 6 2B 3 IN2 C4 12 4 IC102 2 OUT2 4 CN107 C2 5 C3 6 PV SYNC 65 DDC1 VCLK GN IF ON 73 30 SDA1 DDM1 SDA SUB SCL 29 1 2 3 4 5 6 TXD RXD GND GND GND 5V 10 9 8 7 6 5 4 3 2 1 SUB 5V GND TXD RXD TCK TAUX TRES TVPP1 TAUX3 T MODE ECS SUB SDA 30 DDC1 SCL 31 SCL1 IC101 SYSTEM CONTROL CPU ST 47 CH SENS 54 IC105 WDT RESET IC107 EEP ROM VCLK 7 SDA 5 SCL 6 CK 78 RSTX 77 DDC2 VCLK 3 CK 8 RST RCT 6 SW Q101 HSTX 52 32 SDA2 DDC2 SDA CN108 RCT 76 DDC2 SCL 33 SCL2 SOT 19 SIN 20 SCK 18 MD2 51 MD0 49 B-SS3514<J>-A-24 4-1 4-2 E TO B BOARD CN503 B( GV IF RECEIVER SUB SYSTEM CONTROL,INVERTER IC601 GV IF RECEIVER CN502 F SDT P SDT GND SDT N ) 39 REFRQP R0 - R5 41 SDATAN TO U BOARD CN406 42 REFRQN IC603 DC-DC R5 22 DD ON3 5 V+ SHDN 3 G0 15 2 3/5 G0 - G5 CS 6 G5 10 1 OUT EXT 7 IC604 CONTROL D B0 5 B0 - B5 G 63 S 1 IN B5 62 VCC (IC601) IC602 +3.3V REG CN504 OUT 3 1 CTL 2 GND SW Q601 DD ON2 CE 38 8 G TO U BOARD CN402 DD ON U 9 10 11 12 13 14 15 16 17 18 19 20 21 22 HP STAT MUTE CS N SI 23 24 25 26 SCK CPU ST SCL SDA 27 28 29 30 12V 12V 12V 12V 12V 12V 5V 5V 5V(SENS) DE 50 12V SFT CLK 51 5V SW Q602 STBY 5V IC501 SUB SYSTEM CONTROL DD ON3 79 DD ON2 75 80 CKOT FL601 5 8 7 22 HP STAT MUTE CSN SOT1 21 48 29 28 SCK1 CPU ST SDA0 SCL0 KEY INPUT KEY PW KEY PW LED1 PW LED2 IN LED1 IN LED2 IC503 WDT RESET CK 3 RST 8 78 CK 77 RSTX 52 HSTX 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 46 55 47 1 2 3 4 SEN1 44 SEN2 45 E TO A BOARD CN108 LED CTL 6 V REF 71 49 MD0 51 MD2 1 2 3 4 5 6 7 8 9 10 TAUX SCK SIN SOT X1 83 69 PWM I SENS 43 85 18 20 19 1 INVERTER Q654 POWER CN704 AC L OUT NC AC L IN AC L AC IN 6 + 7 3 9 REMOTE 5V(STBY) KEY INPUT KEY PW KEY PW LED1 PW LED2 IN LED1 IN LED2 5V(SENS) GND SEN1 SEN2 SEN3 SEN4 LED CTL V REF GND NC AC N MAIN RECT D701 3 5 IC701 PWM CONTROL F701 SWITCHING Q701 DRIVER 4 1 V IN 4 13 14 00B 1 2 V AUX 6 3 9 V CTR L CN508 + - 4 3 2 1 3 HOT NC GND GND D TO A BOARD CN105 1 2 3 1 4 2 3 K +12V A 2 +3.3V IC707 CONTROL IC706 +5V,+3.3V REG D A1 D A2 D B1 D B2 IC702 R 1 CN702 9 8 CSL3 2 DH3 DL3 GA GB 7 6 5 4 3 2 1 SHDN 23 IC704 CONTROL DH5 DL5 GA GB D B1 D B2 RUN/ON3 28 D A1 D A2 +5V H B-SS3514<J>-G-24 TO H BOARD CN901 H ( USER CONTROL ) H TO B BOARD CN501 5V(STBY) KEY INPUT KEY PW KEY PW LED1 PW LED2 IN LED1 IN LED2 5V(SENS) GND SEN1 SEN2 SEN3 SEN4 LED CTL V REF GND 18 17 S906 INPUT S901 16 15 14 13 12 11 10 9 8 POWER 5V(SENS) D901 D902 D903 IC901 SENSOR 7 6 5 4 3 2 1 2 1 VCC 4 + 3 D930 D931 1 OUT IC902(1/4) 14 13 + 12 IC902(4/4) IC902(3/4) 10 + 8 9 - IC902(2/4) 5 + 7 - 6 AMP Q904 SW Q903 5V(STBY) SW Q904 SW Q904 7 B-SS3514<J>-H-24 B-SS3514<J>-B-24 4-3 12V 12V GND GND GND 12V DEM 13 2 5 12V 3 4 5 6 7 8 PH701 ISOLATOR 7 6 1 2 D705 DS 7 11 GND HOT NC GND T652 1 1 C TO A BOARD CN106 I SENSE 5 S902-905,907 3 2 1 AUDIO R AUDIO GND AUDIO L AUDIO GND CN701 D702 6 3 GND CN507 6 3 IC651(1/2) - OUT1 1 T701 1 2 CN703 LCD PANEL TO LAMP 2 -IN1 1 2 3 4 CN901 4 IC651(2/2) 2 X0 82 T651 5 BUFF Q770 X501 INVERTER Q653 5V(SENSE) OUT2 7 T702 12V SW Q652 -IN2 7 REMOTE INV. Q651 CN705 6 CSL5 13 CN503 T MODE T AUX3 TVPP1 TRES T AUX TCK RXD TXD GND SUB 5V B0 B1 B2 B3 B4 B5 RA0 RA1 RA2 RA3 RA4 RA5 GND GA0 GA1 GA2 GA3 GA4 GA5 GND BA0 BA1 BA2 BA3 BA4 BA5 GND GND GND GND GND LCD DE GND GND GND LCD CLK GND GND GND NC 5V 5V 5V 5V CN501 76 RCT 6 RCT G0 G1 G2 G3 G4 G5 AUDIO IN 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 IC790 BUFFER BUFF Q771 CE 38 FL602 SW Q501 R0 R1 R2 R3 R4 R5 ( POWER SUPPLY,AUDIO IN ) CN706 GND R0 31 . 30 25 40 SDATAP 3 2 1 G CN505 1 4-4 3.3V 3.3V GND GND 5V 5V GND GND DD ON A TO A BOARD CN104 CN401 B TO A BOARD CN101 AUDIO 12V 1 AUDIO 12V GND GND GND 12V 12V 12V STBY 5V 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 AUDIO R AUDIO GND AUDIO L CN SENS CPU ST SDA SCL GND SDT N SDT GND SDT P IC403 AUDIO PROCESS (TRE,BASS,LOUD) IC402 POWER AMP IC408 HPF IC401 STEREO DIPOLE 2 -IN1 CN404 OUT A+ 3 6 INR R OUT 16 26 AIR R OUT 38 3 +IN1 0UT1 1 6 IN A- 11 IN L L OUT 17 29 AIL L OUT 37 5 +IN2 OUT2 7 15 IN B- 6 -IN2 OUT A- 5 1 2 3 4 R OUT+ R OUT+ R OUTR OUT- 1 2 L OUT+ L OUT+ 3 L OUT- 4 L OUT- OUT B+ 18 OUT B- 16 FL401 1 S DOWN 19 SDA BUFF Q408,409 CN405 HP IN 20 EXTAL 41 20 SCL X401 2.8224MHz XTAL 42 62 SI 9 CN403 CSN MUTE Q406.407 STBY 5V HEADPHONE D421 F TO B BOARD CN502 SDT GND SDT N SCL CPU ST SCK SI CSN MUTE HP STAT DD ON U G TO B BOARD CN504 S DOWN SW Q410 3 2 1 SW Q404,405 FL402 CN402 SDA STBY 5V STBY 5V 12V 12V 12V 12V 12V 12V 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 SPEAKER L 61 SCK CN406 SDT P SPEAKER R D414 FL403 +9V IC412 +5V REG IC404 +9V REG 1 IN OUT 3 OUT IN SD5V 2 CTL IC411 AMP SW Q411 IC409 DC-DC 5 V+ A5V 2 3/5 SW Q401 GND 1 +5V OUT 1 IC410 CONTROL 3 SH D EXT 7 G CS 6 S 2 IN A- 3 IN A+ 0UT A 1 5 IN B+ OUT B 7 6 IN B- D416 D U ( AUDIO ) B-SS3514<J>-U-24 4-5 4-6 Terminal name of semiconductors in silk screen printed circuit ( ) 4-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS 4-2. CIRCUIT BOARDS LOCATION Device DISPLAY Note: 1 • All capacitors are in µF unless otherwise noted. (pF: µµF) Capacitors without voltage indication are all 50 V. • Indication of resistance, which does not have one for rating electrical power, is as follows. 2 B 3 Pitch: 5 mm Rating electrical power 1/4 W (CHIP : 1/10 W) H U 4 • All resistors are in ohms. • f : nonflammable resistor. • F : fusible resistor. ¢ : internal component. • • p : panel designation, and adjustment for repair. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. e : earth-ground. • E : earth-chassis. • • All voltages are in V. • Readings are taken with a 10 MΩ digital multimeter. • Readings are taken with a color-bar signal input. • Voltage variations may be noted due to normal production tolerances. • * : Can not be measured. • Circled numbers are waveform references. • s : B + bus. • S : B – bus. a b 5 Note: The components identified by shading and mark ! are critical for safety. Replace only with part number specified. 6 7 8 9 0 !¡ Base Diode Emitter Cathode Anode Diode Anode (NC) Diode Anode (NC) Diode Anode Diode Cathode Common Anode Cathode Common Diode Anode Anode Common Diode Anode Anode Common Diode Cathode Cathode Common Diode !™ Diode !£ Transistor (FET) Cathode Anode Anode Cathode Drain Cathode Cathode Anode Anode Source Gate D D G !¢ Transistor (FET) !∞ Transistor (FET) – Drain Source Gate Source Drain Gate G S S D D G G S S Discrete semiconductot (Chip semiconductors that are not actually used are included.) Note: Les composants identifiés per un tramé et une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. A 4-7 Transistor Emitter Collector Common Ref. No. G Base Cathode 1 Circuit diagram division code Circuit Terminal name Collector Transistor Cathode • Divided circuit diagram One sheet of A, U boards circuit diagrams are divided into two sheets, each having the code A-P1-a to A-P1-b, A-P2-a to A-P2-b, A-P3-a to A-P3-b, U-a to U-b. For example, the destination ab1 on the A-P1-a sheet is connected to ab1 on the A-P1-b sheet. MEDIA ENGINE * Printed symbol 4-8 Ver.1.6 Ref. No. Circuit diagram division code 4-10 TO P2-a TO P2-a 1 DDC2_VCLK DDC2_SCL DDC2_SDA DDC1_SDA DDC2_5V DDC1_VCLK DDC1_SCL DDC1_5V TO P2-a (ECS) CN107 6P TXD RXD GND GND GND 5V 1 2 3 4 5 6 9 8 7 6 5 4 3 2 1 C108 0.01 25V B NC VCC NC VCLK NC SCL VSS SDA IC107 24LC21AT/SN DDC2 C109 0.01 25V B NC VCC NC VCLK NC SCL VSS SDA IC106 24LC21AT/SN DDC1 1 2 3 4 1 4.0 4.4 * R111 15k 1/16W 4.6 4.6 0 R112 15k 1/16W R105 R106 15k 15k 1/16W 1/16W D102 MA151WK-TX R127 0 R126 0 TO P2-a FB3 FB108 0UH FB3 FB107 0UH FB2 FB101 0UH R110 0 R109 0 FB2 FB104 0UH R122 10k 1/16W VCC WC SCL SDA R114 0 R113 0 D105 MA151WK-TX DDC1_GND DDC2_GND E0 E1 E2 VSS FB2 FB103 0UH FB2 FB102 0UH 4.9 4.9 4.9 0 C134 0.01 25V B SER13 R139 10k 1/16W R138 10k 1/16W R132 100 1/16W R131 100 1/16W R130 100 1/16W R129 100 1/16W R151 10k 1/16W 5V SUB_SCL TO P3-b SUB_SDA SER1(1..3) TO P2-b R150 10k 1/16W LED_GREEN LED_UMBER D101 BRPG1201W-TR R116 220 1/16W STBY5V R128 100 1/16W R103 100 1/16W R102 100 1/16W R115 680 1/16W SER11 SER12 R123 10k 1/16W C101 0.1 25V F C113 150 10V R101 100 1/16W STBY5V C114 0.1 25V F Q103 SI2301DS-T1 SW C112 0.1 25V F R135 R136 R137 10k 10k 10k 1/16W 1/16W 1/16W R152 1k 1/16W 0 Q102 DTC114EKA-T146 SW 4.9 R121 10k 1/16W FB3 FB106 0UH FB3 IC103 M24C16-MN6T EEPROM C133 C110 150 150 10V 10V 1 FB105 0UH C 2 GND 5V 3.3V 5V 3.3V ab24 ab22 ab21 ab19 ab18 ab16 ab15 ab13 ab11 ab9 ab7 ab6 ab5 ab4 ab2 ab1 ab23 ab20 ab17 ab14 ab12 ab10 ab8 ab3 12 3 3.3V 3.3V GND GND 5V(STBY) 5V(STBY) GND GND DDON TO G BOARD CN702 G 11 4 (SYSTEM CONTROL) 8 example, the destination ab1 on the A-P1-a sheet is connected to ab1 on the A-P1-b sheet. 10 7 • Divided circuit diagram One sheet of A-P1 board circuit diagram is divided into two sheets, each having the code A-P1-a to A-P1-b . For 9 6 A 8 5 F 7 8 b 6 7 4-9 5 6 4 5 a 2 I 3 H 4 E 8 D 3 7 B 2 6 1 5 CN104 9P (1) Schematic Diagrams of A (P1-P3) Boards 13 14 A-P1-a B-SS3514<J..>-A-P1-a(24) 1 3 2 4 5 6 7 8 10 9 11 12 R124 22 1/16W A REFCLK A8 /WRL /RD ALE AD4 AD7 AD6 AD5 AD4 AD3 AD2 AD(2..7) TO P3-a ab1 CH3_RST IC108 TC74HC4066AFT(EL) SW TO P2-a INPUT_SEL IC102 TC7S04FU(TE85R) INV TO P3-b GV_IFON TO P2-a P3-a CH3_AD0 1 7 C 6 C127 0.1 25V F VCC C1 C4 IO4 OI4 OI3 IO3 R143 0 C129 100p 50V CH C128 0.1 25V F C103 C102 22p 22p 50V 50V CH CH C104 100p 50V CH C105 0.1 25V F R125 4.7k 1/16W R133 100 1/16W 9 10 11 12 13 14 POLV EXITV IO1 OI1 OI2 IO2 C2 C3 GND 4.9 4.9 0 0 0 4.9 CH3_AD1 8 4.9 TO P2-a 2 5 0 0 0 0 0 0 3 2 3 IN B VCC IN A GND OUT 4 0 4 1 HS VS POLH EXITH 5 B R141 10k 1/16W C120 0.1 25V F ab5 H:FLASH WRITTER MODE L:NORMAL MODE 2.0 4 X101 3 C123 0.1 25V F 3.5 4.5 4.5 4.6 ab16 ab17 ab18 C107 100p 50V CH P51/SCL0/SIN0 P52/SDA1 H C125 0.1 25V F 4.9 R118 8 7 1.5 0.7 6 RST VS RCT VCC 5 1 2 3 4 TC NC CK GND R119 1k 1/16W 0.7 D103 1SS355TE-17 4.9 4.9 4.9 2 C131 0.1 25V F 0 0 1 C126 0.1 25V F 3.2 D104 Q101 UDZ-TE-17-12B DTC114EKA-T146 SW 0 IC109 TC7S08FU(TE85R) AND 0.3 4.9 0.6 4.9 4.7 connected to ab1 on the A-P1-b sheet. 3 GND IN A VCC IN B 2 OUT 4.9 4.9 a Circuit diagram division code R146 10k 1/16W R147 10k 1/16W RA101 1 3 5 7 2 4 6 8 RA102 R145 1k 1/16W 1 3 5 7 2 4 6 8 ab21 ab22 CN108 10P 1 2 3 4 5 6 7 8 9 10 ab23 TMODE TAUX3 TVPP1 TRES TAUX TCK RXD TXD GND SUB5V (WRITER) TO P3-b CPU_ST R149 0 TO P3-a CH3_INTI TO P3-b TH101 A-P1-b PVSYNC /CH_SENS CH3_TEMP (SYSTEM CONTROL) R148 1k 1/16W J C111 0.1 25V F ab24 B-SS3514<J..>-A-P1-b(24) Schematic diagram Ò A -P1-a board Schematic diagram 4-11 A 1 Ref. No. R104 10k 1/16W ab20 I b 0 ab19 5V • Divided circuit diagram One sheet of A-P1 board circuit diagram is divided into two sheets, each having the code A-P1-a to A-P1-b . For example, the destination ab1 on the A-P1-a sheet is 0 C130 0.1 25V F R144 1k 1/16W 3.3V 0 R108 10k 1/16W R107 10k 1/16W C106 0.1 25V F 0 0 R120 100 1/16W 1 C132 0.1 25V F 4.9 4 0.3 ab15 R117 100 1/16W 0 0 4.9 0.6 4.9 5 ab13 ab14 4.9 0 4.9 ab12 4.9 1.6 ab11 3.2 F 2.3 0 4.9 0 4.9 0 IC101 MB90F553APF-G-BND-AP SYSTEM CONTROL 31 P53/SCL1 32 P54/SDA2 33 P55/SCL2 34 AVCC 35 AVRH 36 AVRL 37 AVSS 38 P60/AN0 39 P61/AN1 40 P62/AN2 41 P63/AN3 42 VSS 43 P64/AN4 44 P65/AN5 45 P66/AN6 46 P67/AN7 47 P70/IRQ0 48 P71/IRQ1 49 MD0 50 MD1 4.9 4.6 * 4.4 6 8 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 ab10 7 0.3 4.9 0 4.9 ab9 C124 0.01 25V B IC105 MM1170BFB WDT RESET 10k 4.9 1/16W PA4/CKOT PA3 PA2 RSTX PA1/OUT3 PA0/OUT2 P97/PPG5 P96/PPG4 P95/PPG3 P94/PPG2 P93/PPG1 P92/PPG0 P91/OUT1 P90/OUT0 P87/IN3 P86/IN2 P85/IN1 P84/IN0 P83/TOT1 P82/TOT0 P81/TIN1 P80/TIN0 P77/IRQ7 P76/IRQ6 P75/IRQ5 P74/IRQ4 P73/IRQ3 P72/IRQ2 HSTX MD2 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 P22/A18 P23/A19 P24/A20 P25/A21 P26/A22 P27/A23 P30/ALE P31/RDX VSS P32/WRLX P33/WRHX P34/HRQ P35/HAKX P36/RDY P37/CLK P40/SCK P41/SOT P42/SIN P43/SCK1 P44/SOT1 VCC P45/SIN1 P46/ADTG P47/SCK0 C P50/SDA0/SOT0 5 ab7 ab8 P17/AD15 100 P16/AD14 99 P15/AD13 98 P14/AD12 97 P13/AD11 96 P12/AD10 95 P11/AD09 94 P10/AD08 93 P07/AD07 92 P06/AD06 91 P05/AD05 90 P04/AD04 89 P03/AD03 88 P02/AD02 87 P01/AD01 86 P00/AD00 85 VCC 84 X1 83 X0 82 VSS 81 1 2 P21/A17 4 ab4 P20/A16 3 4.9 4.9 4.9 ab3 G 1 2 ab2 E 2.3 0 0.3 D 0 0 0 0 0 0 0 STBY5V ab6 -P1-b board l 4-12 1 3 2 4 A INPUT1 5 6 7 8 10 9 D208 D209 D210 MA3075WA-(TX)MA3075WA-(TX) MA3075WA-(TX) 11 12 L201 47µH CN102 5V BLUE1 3 R209 75 1/10W 9 14 R211 75 1/10W R210 75 1/10W R215 47 1/16W C212 0.1 25V F R217 47 1/16W C214 0.1 25V F 4 1 15 1.7 5 2 R222 47 1/16W D215 MA8082-H-TX 1 2 DDC1_VCLK TO P1-a R253 47 1/16W R256 47 1/16W FB208 FB1 0UH FB209 0UH FB1 C C220 47 10V HS1 RED2 VS1 FB210 FB1 0UH R201 0 FB211 0UH FB1 R202 0 C223 47 10V PS201 2 2 2 2 1 1 1 1 1.3 R229 47 1/16W 1.3 C224 0.01 25V B C225 47 10V TO P1-a R203 0 1.3 R224 47 1/16W GREEN2 DDC1_SCL DDC1_SDA FB212 0UH FB1 C221 0.01 25V B DDC1_GND DDC1_5V VCC1(G) NC IN1(G) VCC1(B)VCC2(G) IN1(B) OUT(G) IN1(H) IN1(V) VCC2(B) GND NC NC 1.7 D214 MA8082-H-TX 10 VCC1(R)VCC2(R) IN1(R) OUT(R) 1.7 GND GND OUT(B) IN2(R) GND GND OUT(SOG) IN2(G) VCC NC NC GND OUT(H) IN2(B) OUT(V) IN2(H) GND IN2(V) SW 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 R279 0 C216 0.01 25V B 1 8 13 C213 47 10V C210 0.1 25V F R212 47 1/16W 2 C209 0.01 25V B GREEN1 C287 22 10V 3 C207 47 10V R278 0 2 C205 22 10V 4 RED1 5 7 ab1 C203 0.01 25V B 6 C201 47 10V R277 0 1 12 B 5V 3 7 11 2 1 3 8 6 2 1 3 18 17 16 15 14 13 12 11 10 9 2 1 C211 0.1 25V F 1 2.0 C215 0.1 25V F 2 2.0 2.0 C218 0.1 25V F ab2 ab3 3 ab4 1.1 C222 0.1 25V F 4.9 IC205 M52758FP VIDEO SW BLUE2 C226 0.01 25V B AGND R258 R259 2.2k 2.2k 1/16W 1/16W ab5 CN103 2 1 6 STBY5V 2 D220 MA8082-H-TX 2 1 1 2 2 3 4 5 6 R235 47 1/16W R236 47 1/16W HS2 R205 0 FB219 0UH FB1 R206 0 FB207 FB1 0UH R207 0 1 CVEXI CLAMP CPSEL GND 2 CVPOL HDRV VDRV CPWID R242 1k 1/16W 0.4 0 0 0 R208 3.9k 1/16W 1.0 Q201 2SC2712G-TE85L BUFFER 0.4 R255 680 1/16W C284 100p 50V CH C242 100p 50V CH C241 0.1 25V F TO P1-a TO P1-b D207 1SS355TE-17 DDC2_SCL DDC2_SDA • A - P2-a BOARD WAVEFORMS R267 22 1/16W ab6 DDC2_GND R244 C249 C250 C247 C248 C246 R243 0 1M 0.47 0.1 0.47 1 1 1/16W 10V 25V 10V 16V 16V B F F B F DDC2_5V PS202 POLH EXITH POLV EXITV IC206 BA7078AF-E2 SYNC DETECTOR VS2 FB218 FB1 0UH VSYNC INVCC 3 7 DDC2_VCLK TO P1-a FB216 FB1 0UH FB217 0UH FB1 F 0.9 5.4 4.9 0 0 0 4.9 4.9 0 10 11 12 13 14 15 16 17 18 5 C260 0.1 25V F 4 D219 MA8082-H-TX HSCTL POLH C/HSYNC INEXIH VIDEO INPOLV VSEPA EXIV 5 10 C237 0.47 10V B 6 4 4.3 1.0 3.0 C236 1 16V F 8 7 14 13 12 11 10 9 8 0 R228 75 1/10W R227 75 1/10W C234 4.7 10V 4.9 0.2 4.7 4.9 0 R226 75 1/10W 1 15 R241 10k 1/16W R282 0 3 9 14 IC208 TC74VHCT14AFT(EL) INV 9 E INPUT_SEL TO P1-b 3 R281 0 8 13 2 1 1 7 12 3 VCC 6A 6Y 5A 5Y 4A 4Y 11 2 1 3 R280 0 1A 1Y 2A 2Y 3A 3Y GND INPUT2 R231 47 1/16W 0 4.9 4.0 0 D D218 D216 D224 MA8082-H-TX D217 MA8082-H-TX MA8082-H-TX MA8082-H-TX D211 D213 D212 MA3075WA-(TX)MA3075WA-(TX) MA3075WA-(TX) R238 R239 2.2k 2.2k 1/16W 1/16W 2 2 2 2 1 D225 MA8082-H-TX 1 1 1 1 H R250 0 D222 MA8082-H-TX D221 D223 MA8082-H-TX MA8082-H-TX G b 0.4 4.9 0.3 0.3 14 13 12 11 10 9 1 7 0.3 0 2 3 4 5 6 7 2 3 4 5 6 R252 100 1/16W 1.0 Vp-p (H) 3 5 7 ab8 0 0 6 0 0.3 0.3 5 0 0.3 4 4.7 4.7 3 VCC 4G 4A 4Y 3G 3A 3Y 1G 1A 1Y 2G 2A 2Y GND 1 2 2 TO P1-b P3-a 8 VCC 4B 4A 4Y 3B 3A 3Y C239 0.1 25V F 1A 1B 1Y 2A 2B 2Y GND C268 100p 50V CH VCC 4G 4A 4Y 3G 3A 3Y 8 1 0 4.7 4.9 14 13 12 11 10 9 H connected to ab1 on the A-P2-b sheet. a 0.3 4.9 4.9 0 0 0 0 H • Divided circuit diagram One sheet of A-P2 board circuit diagram is divided into two sheets, each having the code A-P2-a to A-P2-b . For example, the destination ab1 on the A-P2-a sheet is 8 ab7 HS VS 1G 1A 1Y 2G 2A 2Y GND 14 13 12 11 10 9 C240 0.1 25V F 4 R251 # TH201 IC207 TC74VHC125FT(EL) SYNC SELECT 0.8 Vp-p (H) IC211 TC74VHC125FT(EL) BUFFER IC210 TC74VHC86FT(EL) SYNC SELECT 0.8 Vp-p (H) C285 1000p 50V SL 1 IC203 TC7S32FU(TE85R) SYNC SELECT Ref. No. R283 15k 1/16W 4 R284 15k 1/16W C259 0.1 25V F (RGB PROCESSOR) 2 4 3 5.0 Vp-p (H) 5 5Y 4A 4Y 6Y 5A 3 4.9 4.9 5 6 IC209 TC74VHC04FT(EL) INV 7 4.9 0 1 GND IN A IN B 8 1A 1Y 2A 2Y 3A 3Y GND A-P2-a VCC 6A 14 13 12 11 10 9 4.9 I 4.7 STBY5V 0.3 4.7 0.3 0 FB2 2 VCC FB201 0UH 1 4 OUT 5 4.9 Circuit diagram division code ab9 GND J B-SS3514<J..>-A-P2-a(24) 4-13 4-14 5.0 Vp-p (V) ab2 ab3 ab4 R232 22 1/16W R233 22 1/16W R234 22 1/16W 5V C204 0.1 25V F IC216 BA033FP-E2 +3.3V REG 1 2 VCC OUT GND 3 C206 0.1 25V F C208 150 10V 5V A3.3V 3.3V R264 100 1/16W R290 10k 1/16W C251 0.1 25V F C230 0.1 25V F C254 0.068 16V B C276 0.1 25V F C278 0.1 25V F C279 0.068 16V B C280 0.1 25V F C281 0.1 25V F C282 0.068 16V B C283 0.1 25V F C288 0.1 25V F TO P3-b A3.3V FB2 FB214 C289 0.1 25V F C233 0.1 25V F NC NC NC VD GND GND R IN VD GND VD VD GND GND GND G IN VD GND VD VD GND GND B IN VD GND VD GND CKINV CLAMP SDA SCL A0 A1 PVD PVD GND NC NC NC C217 0.1 25V F R299 10k 1/16W C235 0.1 25V F R291 1.2k 1/16W R298 22 1/16W R296 82 1/16W RA203 100 C238 0.1 25V F 2 4 6 8 2 4 6 8 1 3 5 7 1 3 5 7 IC214 AD9884AKS-100 A/D CONVERT C291 C292 C293 C294 0.01 0.22 0.1 0.1 25V 10V 25V 25V B F F B R292 10k 1/16W C290 0.1 25V F C295 0.1 25V F 3.3V RA204 100 C244 0.1 25V F DRB0 DRB1 DRB2 DRB3 DRB4 DRB5 DRB6 DRB7 VDD GND DGA0 DGA1 DGA2 DGA3 DGA4 DGA5 DGA6 DGA7 VDD GND DGB0 DGB1 DGB2 DGB3 DGB4 DGB5 DGB6 DGB7 VDD GND DBA0 DBA1 DBA2 DBA3 DBA4 DBA5 DBA6 DBA7 C296 0.1 25V F 3.3V 2 4 6 8 2 4 6 8 R295 0 1 3 5 7 1 3 5 7 RA208 100 1 3 5 7 1 3 5 7 RA207 100 RA206 100 2 4 6 8 2 4 6 8 RA205 100 C245 22 10V R AD TO P3-a FB3 FB213 0UH C299 0.1 25V F C298 0.1 25V F C297 0.1 25V F R213 0 R214 0 R216 0 R219 0 R218 0 R220 0 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 TO P3-a G AD AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 R294 0 G G G G G G G G B B B B B B B B GND B AD TO P3-a PIXCLK TO P3-a HSYNCSY TO P3-a 4-16 l -P2-b board R269 R289 100 10k 1/16W 1/16W 8 7 A FB2 6 I FB221 0UH 5 H FB2 4 Ref. No. FB220 0UH R285 R274 10k 10k 1/16W 1/16W 3 Circuit diagram division code ab1 ab5 SER1(1..3) TO P1-a VCC 2 EO 2B 2A 2 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 1 1 2 3 4 5 6 7 8 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 R R R R R R R R connected to ab1 on the A-P2-b sheet. IC212 SN74CBTD3306PWR 1 OE 1A 1B GND C219 0.1 25V F 14 13 12 11 10 9 1 • Divided circuit diagram One sheet of A-P2 board circuit diagram is divided into two sheets, each having the code A-P2-a to A-P2-b . For example, the destination ab1 on the A-P2-a sheet is ab7 C243 0.1 25V F E 8 7 6 5 C 1 2 3 4 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 F A -P2-a board Schematic diagram Schematic diagram SER11 IC215 TC74VHC125FT(EL) BUFFER R225 0 -P2-b (RGB PROCESSOR) J ab6 SER12 B VD REFIN REFOUT PWRDNB VD GND GND GND VDD GND NC HSOUT DATACK/ DATACK VDD GND DRA0 DRA1 DRA2 DRA3 DRA4 DRA5 DRA6 DRA7 VDD GND b ab8 D GND HSYNC COAST GND PVD CKEXT FILT NC GND PVD GND PVD GND GND GND VDD DBB7 DBB6 DBB5 DBB4 DBB3 DBB2 DBB1 DBB0 GND VDD a VCC 4G 4V 4Y 3G 3A 3Y 1G 1A 1Y 2G 2A 2Y GND 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 G 4-15 Ò A ab9 A B-SS3514<J..>-A..-P2-b(24) 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TO P1-b REFCLK CH3_AD0 CH3_AD1 AD(2..7) A8 3.3V ALE /WRL GND /RD CH3_RST A3.3V AGND C301 22 10V C309 0.1 25V F R319 0 FB3 FB316 0UH C315 C316 C317 C318 0.1 22 0.1 22 25V 10V 25V 10V F F A3.3V C328 0.1 25V F C329 0.1 25V F C330 1000p 50V SL C331 0.1 25V F C334 0.1 25V F C336 0.1 25V F C337 1000p 50V SL C339 0.1 25V F C340 0.1 25V F C345 0.1 25V F C346 1000p 50V SL C347 0.1 25V F R301 0 C310 100p 50V CH AD6 AD5 AD2 C311 0.1 25V F C312 100p 50V CH CH3_INTI TO P1-b FB2 FB301 0UH C307 0.1 25V F C308 100p 50V CH C374 0.1 25V F C313 0.1 25V F R338 10k C375 1/16W 100p 50V CH R337 22 1/16W 1 2 OC OUT VDD X301 VSS 4 3 1 FB2 FB321 0UH C314 100p 50V CH 4 5 6 7 8 IC301 CHEETAH3 SCAN CONVERTER C354 0.1 25V F LCDG4 LCDG5 LCDG0 LCDG1 LCDG2 LCDG3 FB350 FB348 FB349 FB347 FB346 FB345 LCDR2 LCDR3 LCDR4 LCDR5 LCDR0 LCDR1 3.3V VDD_8 120 SDDATA(5)119 SDDATA(4)118 SDDATA(3)117 SDDATA(2)116 SDDATA(1)115 SDDATA(0)114 VSS_8 113 MEMCLKOUT 112 VDD_7 111 SDDQS 110 SDDQM 109 SDRAS 108 SDWE 107 SDCAS 106 SDADDR(12)105 SDADDR(11)104 SDADDR(10)103 SDADDR(9)102 SDADDR(8)101 VSS_7 100 SDADDR(7) 99 SDADDR(6) 98 SDADDR(5) 97 SDADDR(4) 96 SDADDR(3) 95 SDADDR(2) 94 SDADDR(1) 93 SDADDR(0) 92 VDD_6 91 PSHIFTCLK 90 VSS_6 89 PVSYNC 88 PHSYNC 87 PDE 86 PDATA(40) 85 PDATA(41) 84 PDATA(42) 83 PDATA(43) 82 PDATA(44) 81 PDATA(45) 80 VDD_5 79 PDATA(46) 78 PDATA(47) 77 PDATA(32) 76 PDATA(33) 75 PDATA(34) 74 PDATA(35) 73 VSS_5 72 PDATA(36) 71 PDATA(37) 70 PDATA(38) 69 PDATA(39) 68 PDATA(24) 67 PDATA(25) 66 VDD_4 65 PDATA(26) 64 PDATA(27) 63 PDATA(28) 62 PDATA(29) 61 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 C373 100p 50V CH FB354 FB353 FB351 FB352 LCDB0 LCDB1 LCDB2 LCDB3 LCDB4 LCDB5 C367 0.1 25V F 3.3V 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 R303 0 3.0 Vp-p (16nsec) SDDT11 SDDT10 SDDT9 SDDT8 SDDT7 SDDT6 RED3 RED2 RED1 RED0 R344 10k 1/16W R345 10k 1/16W 3 C353 0.1 25V F FB358 FB357 FB356 FB355 RED5 RED4 HS VS RESET MCRD NC NC PWM(1) PWM(0) ADCISO1 ADCISO2 ADCISO3 ADCISO4 ANAB ADCISO5 VREFHB ADCISO6 AVDDB3 AGNDB3 AVDDB2 AGNDB2 AVDDB AGNDB ADCISO7 VREFLB ADCISO8 ADCISO9 ANAG ADCISO10 VREFHG ADCISO11 AVDDG3 AGNDG3 AVDDG2 AGNDG2 AVDDG AGNDG ADCISO12 VREFLG ADCISO13 ADCISO14 ANAR ADCISO15 VREFHR ADCISO16 AVDDR3 AGNDR3 AVDDR2 AGNDR2 AVDDR AGNDR ADCISO17 VREFLR ADCISO18 ADCISO19 AHSYNCR AVSYNC CAPCLK2 CAPCLK1 CAPCLK3P CAPCLK3N VDD_1 AHSYNCS 2 C371 100p 50V CH FB362 FB361 FB360 FB359 GREEN1 GREEN0 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 • A - P3-a BOARD WAVEFORMS SDDT23 SDDT22 SDDT21 SDDT20 SDDT19 SDDT18 GREEN5 GREEN4 GREEN3 GREEN2 F PIXCLK HSYNCSY 1 R AD BLUE5 BLUE4 BLUE3 BLUE2 BLUE1 BLUE0 C368 100p 50V CH C322 0.1 25V FB326 FB327 FB325 FB328 FB329 FB330 FB331 FB332 FB333 FB334 FB335 FB336 FB341 FB342 FB344 FB343 SDAD12 SDAD11 SDAD10 SDAD9 SDAD8 SDAD7 SDAD6 SDAD5 SDAD4 FB339 SDAD1 FB338 SDAD2 FB340 SDAD0 Circuit diagram division code B-SS3514<J..>-A-P3-a(24) ab1 ab2 ab3 ab4 ab5 ab7 ab9 ab11 ab13 ab6 ab8 ab10 ab12 J 1 b FB337 SDAD3 R348 connected to ab1 on the A-P3-b sheet. FB324 F SDDT5 SDDT4 SDDT3 SDDT2 SDDT1 SDDT0 C327 100p 50V CH C335 0.1 25V F C369 0.1 25V F C341 100p 50V CH C348 0.1 25V F C370 100p 50V CH ab14 ab15 ab16 ab17 4-18 4-17 SDDT31 SDDT30 SDDT29 SDDT28 SDDT27 SDDT26 SDDT25 SDDT24 1 SDDT17 SDDT16 SDDT15 SDDT14 SDDT13 SDDT12 G G AD E C350 1000p 50V SL C372 0.1 25V F TO P2-b B B B B B B B B G G G G G G G G AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 a I AD4 AD3 D • Divided circuit diagram One sheet of A-P3 board circuit diagram is divided into two sheets, each having the code A-P3-a to A-P3-b . For example, the destination ab1 on the A-P3-a sheet is H AD7 R AD7 R AD6 R AD5 R AD4 R AD3 R AD2 R AD1 R AD0 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 TO P1-b P2-a A -P3-a (SCAN CONVERTER) MCWR MCINT MCALE VDD_13 CHIPSELECT MCAD(8) MCAD(7) VSS_13 MCAD(6) MCAD(5) MCAD(4) MCAD(3) MCAD(2) MCAD(1) MCAD(0) VDD_12 REFCLK VSS_12 VDD_11 PANELCLK VSS_11 MEMCLK VDD_PCLK GND_PCLK VDD_MCLK GND_MCLK TEST VPD PENBKL PENVDD VDD_10 SDDATA(31) SDDATA(30) SDDATA(29) SDDATA(28) SDDATA(27) SDDATA(26) SDDATA(25) SDDATA(24) VSS_9 SDDATA(23) SDDATA(22) SDDATA(21) SDDATA(20) SDDATA(19) SDDATA(18) VDD_9 SDDATA(17) SDDATA(16) SDDATA(15) SDDATA(14) SDDATA(13) SDDATA(12) VSS_9 SDDATA(11) SDDATA(10) SDDATA(9) SDDATA(8) SDDATA(7) SDDATA(6) DVSYNC DDE DHSYNC VSS_1 CLAMPOUT RGB(23) RGB(22) RGB(21) RGB(20) RGB(19) RGB(18) RGB(17) RGB(16) RGB(15) RGB(14) RGB(13) RGB(12) RGB(11) RGB(10) RGB(9) RGB(8) RGB(7) RGB(6) RGB(5) RGB(4) RGB(3) RGB(2) RGB(1) RGB(0) VSS_2 PDATA(7) PDATA(6) PDATA(5) PDATA(4) PDATA(3) PDATA(2) VDD_2 PDATA(1) PDATA(0) PDATA(15) PDATA(14) PDATA(13) PDATA(12) VSS_3 PDATA(11) PDATA(10) PDATA(9) PDATA(8) PDATA(23) PDATA(22) VDD_3 PDATA(21) PDATA(20) PDATA(19) PDATA(18) PDATA(17) PDATA(16) VSS_4 PDATA(31) PDATA(30) B AD C TO P2-b B TO P1-b A 10 9 8 7 6 5 4 3 2 1 Ref. No. ab2 C304 C305 22 0.1 10V 25V F FB302 0UH FB2 FB2 C306 22 10V 3.3V C302 100p 50V CH C303 0.01 25V B R302 10k 1/16W 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 1 2 3 4 5 6 7 8 SDRAM IC302 MT48LC1M16A1TG-7S C320 100p 50V CH C333 0.01 25V B R307 10k 1/16W C321 0.01 25V B 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 1.2 1.2 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 C319 100p 50V CH SDDT22 SDDT23 FB303 0UH SDCLK SDDT9 SDDT8 C332 100p 50V CH 0.7 0.8 ab3 ab1 ab4 SDAD9 SDAD8 SDAD7 SDAD6 SDAD5 SDAD4 0 0 1.1 1.1 1.1 1.5 SDAD12 SDAD11 SDAD10 SDAD0 SDAD1 SDAD2 SDAD3 SDAD9 SDAD8 SDAD7 SDAD6 SDAD5 SDAD4 0 0 1.1 1.1 1.1 1.5 SDDQM /SDRAS /SDWE /SDCAS FB2 C338 22 10V 0.8 1.3 1 C342 100p 50V CH 2 3.3V 3 4 FB2 C364 0.1 25V F 5 6 7 C383 100p 50V CH C357 0.1 25V F C381 100p 50V CH FB2 FB310 FB311 0UH 0UH VCC GNDA VCCA REXT GNDT SDATAN SDATAP CKPOL LPFB LPFA CE GND TO P1-b GV_IFON 0 1.8 3.2 0 1.8 3.2 0 2.8 2.6 3.2 0 1.1 0 0 1.5 1.5 1.6 8 SDRAM IC303 MT48LC1M16A1TG-7S C343 100p 50V CH Pattern inductance 0.1-0.4nH R322 51 1/16W C362 0.01 25V B CN105 8P 12V 12V 12V 12V GND GND GND GND FL4 FL303 3 4 5 6 1 2 3 4 5 6 7 8 CN106 4P 2 7 8 9 10 AUDIO R AUDIO GND AUDIO L AUDIO GND 1 TO G BOARD CN701 TO G BOARD CN705 TO P1-a SUB_SDA SUB_SCL TO P1-b CPU_ST R339 4.7 1/16W R340 4.7 1/16W STBY5V Q303 SI2301DS-T1 12V SW 6.1 C377 0 FL302 R342 10k 1/16W 6.1 Q301 SI2301DS-T1 12V SW FB1 FB319 0UH FB318 0UH FB1 FB3 FB320 0UH 0.6 Q302 SI2301DS-T1 5V SW C376 0 R341 10k 1/16W R343 10k 1/16W 1 2 3 4 SDRAM(512kx2x16bitx2) C344 0.01 25V B 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 C349 22 10V TO P2-b A 3.3V C351 22 10V C352 22 10V C356 0.1 25V F R323 R321 4.7k 51 1/16W 1/16W R327 1k 1/16W C360 R326 680p 1k 25V 1/16W CH R325 4.7k 1/16W SDAD12 SDAD11 SDAD10 SDAD0 SDAD1 SDAD2 SDAD3 FB308 0UH FB2 IC304 CXB1455R GV IF TRANSMITTER SDDT20 SDDT21 1.2 1.2 FB309 0UH C355 0.1 25V F GND B3 B2 B1 B0 G7 G6 G5 G4 G3 G2 VCC SDDT11 SDDT10 SDDT6 SDDT7 ab5 ab7 ab9 ab10 C380 100p 50V CH TO P1-b PVSYNC LCDB3 LCDB2 LCDB1 LCDB0 LCDG5 LCDG4 LCDG3 LCDG2 C361 0.1 25V F 0.8 0.8 0.6 1.2 ab6 ab8 ab13 ab12 ab17 ab14 C382 100p 50V CH SDDT25 SDDT24 0.7 0.6 FL301 C358 0.1 25V F 12V C365 0.1 25V F STBY5V A-P3-b C366 10 35V connected to ab1 on the A-P3-b sheet. C359 22 10V R320 10k 1/16W 2.9 2.8 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 CN101 26P SDT_GND SDT_N CN_SENS CPU_ST SDA SCL GND AUDIO_R AUDIO_GND AUDIO_L AUDIO_12V AUDIO_12V GND GND GND 12V 12V 12V STBY_5V B-SS3514<J..>-A-P3-b(24) SDT_P TO U BOARD CN401 4-20 l -P3-b board 0.5 0.5 SDDT18 SDDT19 GV IF Transmitter R347 220 1/16W /CH_SENS TO P1-b D306 1SS355TE-17 J SDDT27 SDDT26 SDDT13 SDDT12 SDDT4 SDDT5 (GV IF TRANSMITTER) Ref. No. 1.0 0.6 1.2 1.0 D004 MA151WK-TX Schematic diagram Schematic diagram A -P3-a board Circuit diagram division code I SDDT29 SDDT28 0.5 0.4 0.6 1.0 1 1.2 0.6 SDDT16 SDDT17 SDDT2 SDDT3 b a SDDT31 SDDT30 SDDT15 SDDT14 0.5 0.5 25 26 27 28 29 30 31 32 33 34 35 36 0 2.8 2.6 3.2 0 1.1 0 0 1.5 1.6 1.5 F • Divided circuit diagram One sheet of A-P3 board circuit diagram is divided into two sheets, each having the code A-P3-a to A-P3-b . For example, the destination ab1 on the A-P3-a sheet is H 1.2 1.2 VSS DQ15 DQ14 VSSQ DQ13 DQ12 VDDQ DQ11 DQ10 VSSQ DQ9 DQ8 VDDQ NC/RFU UDQM CLK CKE NC A9 A8 A7 A6 A5 A4 VSS VDD DQ0 DQ1 VSSQ DQ2 DQ3 VDDQ DQ4 DQ5 VSSQ DQ6 DQ7 VDDQ LDQM WE CAS RAS CS BA A10/AP A0 A1 A2 A3 VDD 1.2 1.2 VSS DQ15 DQ14 VSSQ DQ13 DQ12 VDDQ DQ11 DQ10 VSSQ DQ9 DQ8 VDDQ NC/RFU UDQM CLK CKE NC A9 A8 A7 A6 A5 A4 VSS VDD DQ0 DQ1 VSSQ DQ2 DQ3 VDDQ DQ4 DQ5 VSSQ DQ6 DQ7 VDDQ LDQM WE CAS RAS CS BA A10/AP A0 A1 A2 A3 VDD SDDT0 SDDT1 E LCDB4 LCDB5 D001 D002 D003 MA151WK-TX MA151WK-TX MA151WK-TX G LCDR5 LCDR4 LCDR3 LCDR2 LCDR1 LCDR0 1 2 3 4 5 6 7 8 12 11 10 9 48 47 46 45 44 43 42 41 40 39 38 37 D ab15 ab16 B VCC B4 B5 B6 B7 VSYNC HSYNC SFTCLK DE CNTL REFREQ GND GND G1 G0 R7 R6 R5 R4 R3 R2 R1 R0 VCC 13 14 15 16 17 18 19 20 21 22 23 24 LCDG1 LCDG0 C 4-19 Ò A ab11 A 13 12 11 10 9 8 7 6 5 4 3 2 1 (a) • A BOARD SEMICONDUCTOR LOCATION [ RGB PROCESS, SCAN CONVERTER, GVIF TRANSMITTER, SYSTEM CONTROL ] — A BOARD (Conductor Side) — IC — A BOARD (Component Side) — Component ( Conductor ) Side ) ( Side 1 2 3 4 5 1 2 3 4 5 A A B B IC101 IC102 IC103 IC105 IC106 IC107 IC108 IC109 IC203 IC205 IC206 IC207 IC208 IC209 IC210 IC211 IC212 IC214 IC215 IC216 IC301 IC302 IC303 IC304 B–4 B–1 A–4 C–2 A–2 A–2 C–1 B–2 B–3 F–2 B–2 B–3 B–3 B–3 B–3 B–4 E–4 E–2 F–4 D–3 E–4 E–2 E–2 F–4 TRANSISTOR Component ( Conductor )* Side ) ( Side C C Q101 Q102 Q103 Q201 Q301 Q302 Q303 C–2 D–2 D–3 B–3 G–1 F–2 F–1 2 2 !£ 2 !£ !£ !£ DIODE D D E E F F Component ( Conductor )* Side ) ( Side D101 D102 D103 D104 D105 D207 D208 D209 D210 D211 D212 D213 D214 D215 D216 D217 D218 D219 D220 D221 D222 D223 D224 D225 D306 A–4 A–2 B–2 B–2 A–2 B–3 F–1 F–2 F–2 F–2 F–2 F–2 F–1 F–1 F–1 F–1 F–1 F–3 F–3 F–3 F–3 F–3 F–1 F–2 F–2 – 9 3 3 9 3 !¡ !¡ !¡ !¡ !¡ !¡ 3 3 3 3 3 3 3 3 3 3 3 3 3 CLYSTAL Component ( Conductor ) Side ) ( Side G G X101 X301 C–3 D–3 *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 4-8) 4-21 4-22 (2) Schematic Diagrams of B (P1-P3) Boards 1 6 7 8 10 9 11 12 FL603 NFM60R20 R0 R1 TO P2 CE RFB602 R607 100 1/16W RFB4 C604 0.1 25V F C603 0.1 25V F C602 0.1 25V F STBY_5V FB613 R601 10k 1/16W FB1 3.3V DDON_U TO P2 R604 4.7k 1/16W FL601 NFA3216G2C101 HP_STAT R611 5.6k 0 1/16W (1%) 2 1 FL602 NFA3216G2C101 6 3 4 5 10 7 8 9 R610 4.7k 1/16W R609 4.7k 1/16W R608 4.7k 1/16W SCK B_CPU_ST SCL TO P2 R613 150 1/16W SDA (1%) C610 47p 50V CH R615 100 1/16W (1%) C612 47p 50V CH 3 2 1 R606 4.7k 1/16W R617 150 1/16W 3.3 3.3 3.3 4.8 2.7 2.0 2.0 2.7 3.3 C614 0.1 25V F (1%) Pattern Inductance 0.1-0.4nH 3.0 R619 47 1/16W E C613 22 10V 2.8 C616 470p R620 47 1/16W 1 2 IC601 CXB1456R GV IF RECEIVER 3 R631 10k 1/16W R4 R5 8 6 4 2 7 5 3 1 VCCT 16 0.8 G0 15 0 G1 14 1.2 G2 13 1.2 G3 12 1.2 G4 11 1.2 G5 10 VEET 9 VCCT 8 G6 7 G7 6 1.2 B0 5 1.2 B1 4 1.2 B2 3 1.2 B3 2 VEET 1 RFB603 RFB4 G0 G1 G2 G3 G4 G5 RFB604 RFB4 C611 0.1 25V F G0 G1 G2 G3 8 6 4 2 7 5 3 1 G4 G5 8 6 4 2 7 5 3 1 B0 B1 B2 B3 RFB605 RFB4 RFB606 RFB4 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 B0 B1 B2 B3 8 6 4 2 7 5 3 1 B4 B5 8 6 4 2 7 5 3 1 C615 0.1 25V F FB604 FB2 C617 0.1 25V F C606 0.1 25V F C608 0.1 25V F 7 5 3 1 C609 0.1 25V F (1%) FB2 C605 22 10V 33 REXT 34 PANEL0 35 PANEL1 36 LOS 37 TESTDT 38 CE 39 REFRQP 40 SDATAP 41 SDATAN 42 REFRQN 43 TESTEXN 44 VCCA 45 VEEA 46 VEES 47 LPFA 48 LPFB (1%) FB601 3.3V 8 6 4 2 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 TO P2 1.2 1.2 MUTE CSN SI R0 R1 R2 R3 C618 0.1 25V F C619 0.1 25V F B5 B4 10 9 8 7 0 1.2 1.2 1.2 1 6 5 4 3 R1 VEET VCCT VEEG VCCG R2 R3 R4 R5 VEEG VCCG R6 R7 VEET C601 0.1 25V F CN502 3P F R2 R3 R4 R5 12V 2 SDT_P SDT_GND SDT_N TO U BOARD CN406 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 FB602 FB2 58 FB603 FB2 59 FB605 FB2 60 C627 0.1 25V F 0 0 1.1 DDON_U HP_STAT MUTE CSN SI SCK CPU_ST SCL SDA TO U BOARD CN402 CN505 60P (GV IF RECEIVER) C626 39 16V CLKPOL R0 12V 12V 12V 12V 12V 12V 5V 5V B-P1 GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 CNTL DE SFTCLK VEET VCCT VEEG VCCG HSYNC VSYNC B7 B6 VEEG VCCG B5 B4 VCCT B D 5 CN504 30P GND GND GND GND GND GND GND GND C 4 2.4 1.0 A 3 2 IC602 PQ20VZ5U +3.3V REG 5V 1 RFB4 R632 22 1/16W 5 2 CTL OUT G IN 3.6 3.6 RFB607 1.2 adj 4 R624 1k 1/16W 3 C620 0.33 16V F R625 1.6k 1/16W C621 22 10V FB606 FB2 R633 22 1/16W 0 G GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND RA0 RA1 RA2 RA3 RA4 RA5 GND GA0 GA1 GA2 GA3 GA4 GA5 GND BA0 BA1 BA2 BA3 BA4 BA5 GND GND GND GND GND LCD_DE GND GND GND LCD_CLK GND GND GND NC 5V 5V 5V 5V TO LCD PANEL (1%) 5V Q601 DTC114EKA-T146 SW R626 0 Q602 SI2301DS-T1 5V SW 0 DDON2 TO P2 C622 10 16V C623 0.1 25V F B-SS3514<J..>-B-P1(24) 12V GND H IC603 MAX1626ESA DC-DC 4 REF SHDN 3/5 OUT DDON3 TO P2 3 V+ CS EXT GND 2 7 10.9 8 R634 0.05 1/2W C629 0.1 25V 1.3 0 5V(SENS) 1 6 5 C628 39 16V 10.9 2 8 1 3 7 D D D D 6 S S S G L601 47µH D604 PTZ-TE25-6.2A 5V 5 3 2 R635 100 1/16W 4 I 1 • B - P1 BOARD WAVEFORMS H IC604 D601 SI443IDY D3FS4A CONTROL C630 100 6.3V C631 100 6.3V C632 100 6.3V 4.0 Vp-p (H) H 4.0 Vp-p (H) 4.0 Vp-p (H) Schematic diagram 4-23 B -P1 board l 4-24 1 3 2 A 4 5 6 7 8 10 9 FB501 FB502 FB2 FB2 12 DDON_U TO P1 DDON3 DDON2 PWM TO P3 STBY_5V C527 100 6.3V 11 FB504 FB1 0 0 2.6 4.8 TO P1 SCK TO P1 SI 0 E C517 0.1 25V F TO P1 SDA TO P1 SCL R519 10k 1/16W 3.5 4.5 4.4 R520 10k 1/16W C514 0.1 25V F C515 100p 50V CH 0 0 1.2 4.8 4.6 4.8 4.8 F P51/SCL0/SIN0 P52/SDA1 * 4.8 D C506 0.22 10V F C507 0.01 25V B C508 0.1 25V F 0 0 4.8 0.2 R507 100 1/16W 0 R508 100 1/16W 7 RST VS RCT VCC 4.8 1/16W 1.4 0.5 6 TC NC CK GND 5 1 4.8 2 0.4 0 8 IC503 MM1170BFB WDT RESET R510 10k PA3 PA2 RSTX PA1/OUT3 PA0/AUT2 P97/PPG5 P96/PPG4 P95/PPG3 P94/PPG2 P93/PPG1 P92/PPG0 P91/OUT1 P90/OUT0 P87/IN3 P86/IN2 P85/IN1 P84/IN0 P83/TOT1 P82/TOT0 P81/TIN1 P80/TIN0 P77/IRQ7 P76/IRQ6 P75/IRQ5 P74/IRQ4 P73/IRQ3 P72/IRQ2 HSTX MD2 IC501 MB90F553AFP SUB SYSTEM CONTROL C513 100p 50V CH C512 0.1 25V F 31 P53/SCL1 32 P54/SDA2 33 P55/SCL2 34 AVCC 35 AVRH 36 AVRL 37 AVSS 38 P60/AN0 39 P61/AN1 40 P62/AN2 41 P63/AN3 42 VSS 43 P64/AN4 44 P65/AN5 45 P66/AN6 46 P67/AN7 47 P70/IRQ0 48 P71/IRQ1 49 MD0 50 MD1 8 0 C503 22p 50V CH P16/AD14 99 P15/AD13 98 P14/AD12 97 P13/AD11 96 P12/AD10 95 P11/AD09 94 P10/AD08 93 P07/AD07 92 P06/AD06 91 P05/AD05 90 P04/AD04 89 P03/AD03 88 P02/AD02 87 0 P01/AD01 86 0 P00/AD00 85 VCC 84 2.2 X1 83 2.3 X0 82 VSS 81 1 2 3 4 7 CSN MUTE P22/A18 P23/A19 P24/A20 P25/A21 P26/A22 P27/A23 P30/ALE P31/RDX VSS P32/WRLX P33/WRHX P34/HRQ P35/HAKX P36/RDY P37/CLK P40/SCK P41/SOT P42/SIN P43/SCK1 P44/SOT1 VCC P45/SIN1 P46/ADTG P47/SCK0 C P50/SDA0/SOT0 5 HP_STAT TO P1 P21/A17 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 C 0 0 1.6 4.8 4 1 3 1 PA4/CKOT P20/A16 6 0 4.8 4.8 P17/AD15 100 B STBY5V 3 C511 100p 50V CH 4 C510 0.1 25V F R518 C504 10k 1/16W 22p 50V CH 2 X501 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 GND R509 1k 1/16W 0.2 C509 D501 0.1 1SS355TE-17 25V F 2 C516 0.1 25V F 2.2 0.1 1 D502 Q501 UDZ-TE-17-12B DTC114EKA-T146 SW 4.7 RA501 100X4 2 4 6 8 0 1 3 5 7 RA502 C522 0.1 25V F R534 10k 1/16W 100X4 2 4 6 8 1 3 5 7 4.8 CN503 10P 1 2 3 4 5 6 7 8 9 10 TMODE TAUX3 TVPP1 TRES TAUX TCK RXD TXD GND SUB5V TO A BOARD CN108 4.8 * R501 10k 1/16W R502 10k 1/16W C518 0.1 25V F R503 10k 1/16W TO P1 B_CPU_ST TO P3 I_SENS R525 10k 1/16W G CN501 18P FB505 FB2 R533 10k 1/16W H FB503 5V(SENS) 5V R535 180k 1/16W FB2 CE TO P1 R536 10k 1/16W I C525 10 10V B-P2 D503 1SS355TE-17 C520 10 16V C521 0.1 25V F 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 (SUB SYSTEM CONTROL) REMOTO 5V(STBY) KEY INPUT_KEY PW_KEY PW_LED1 PW_LED2 IN_LED1 IN_LED2 5V(SENS) GND SEN1 SEN2 SEN3 SEN4 LED_CTL VREF GND TO H BOARD CN901 B-SS3514<J..>-B-P2(24) J 4-25 4-26 • B - P2 BOARD WAVEFORMS 1 4.4 Vp-p (4MHz) 1 3 2 4 5 6 7 8 10 9 11 12 A PS651 L653 22µH L651 47µH 12V 2A 12V TO P2 PWM 5V(SENS) TO P2 I_SENS Q653 FZT853-TA INV 11.3 T651 TRANSFORMER POWER 0.3 B R651 100k 1/16W 1 R653 1k 1/4W GND R657 0 C653 39 16V R658 0 C Q652 DTA143XKA-T146 SW 6 0.1 R654 1k 1/4W CN507 2P 4 C652 0.12 100V 0.3 3 2 1 3 5.8 R652 5.1k 1/16W R659 0 0 4.8 Q651 DTC114EKA-T146 INV 2 R655 1k 11.5 1/4W R656 1k 1/4W HOT NC GND TO LAMP 11.3 Q654 FZT853-TA INV 5 7 T652 TRANSFORMER POWER 0 D 1 6 L652 47µH CN508 2P 4 5V R667 R668 R671 39k 10k 22k 1/16W 1/16W 1/16W IC651 µPC393G2 F OUTB IN A+ IN B- 6 V- IN B+ 5 B-P3 C655 0.1 25V R665 56k 1/16W R664 24k 1/16W R663 1.8k 1/16W 2 5 R669 0.22 1/4W 7 R670 0.22 1/4W C659 R672 0.1 39k 25V 1/16W G B-SS3514<J..>-B-P3(24) Schematic diagram -P2 board 5.0 0 0 C657 0.1 25V (INVERTER) Ò B R666 4.7M 1/16W 8 IN A- 7 1 V+ OUTA 2 C658 47 16V C656 1000p 3 0 5.0 5.0 4 E 3 2 1 3 Schematic diagram 4-27 B -P3 board l 4-28 HOT NC GND TO LAMP (b) [ GV IF RECEOVER SIB SYSTEM CONTROL, INVERTER ] — B BOARD (Conductor Side) — — B BOARD (Component Side) — B BOARD Terminal name of semiconductors in silk screen printed circuit (* ) Ref. * Q501, Q601, Q651, Q652 2 Q602 !£ Q653, Q654 !§ D501 - D503, D601, D603 3 *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 4-9) 4-29 4-30 (3) Schematic Diagram of H Board 1 3 2 4 5 6 7 8 10 9 11 12 13 A H USER R910 8.2k 1/16W R909 2.7k 1/16W R908 1.5k 1/16W R907 820 1/16W R906 3.3k 1/16W STBY5V 5V (STBY) INPUT R905 680 1/16W CONTROL R903 2.4k 1/16W R904 680 1/16W R902 680 1/16W D901 S904 SW-1 S902 SW-1 + D911 MA8082-H-TX MENU S903 SW-1 C 2 1 2 1 D909 MA8082-H-TX S905 SW-1 D910 MA8082-H-TX S907 SW-1 D903 AA1101W-TR B D902 AA1101W-TR 1 3 BRPG1201W-TR S906 SW-1 S901 SW-1 POWER D915 MA8082 D914 MA8082 2 4 C903 22 16V CN901 18P D913 MA8082 2 2 2 2 1 1 1 1 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 D906 MA8082-H-TX D908 D907 MA8082-H-TX MA8082-H-TX C901 0.01 25V B VCC OUT 4 GND 3 GND D 2 1 IC901 IS455J SENSOR 4.4 E C902 22 16V R911 560k 1/16W 5V 5V (STBY) 1.5 Q930 DTC143TKA-T146 SW R941 100k 1/16W R940 470k 1/16W R939 15k 1/16W C934 0.1 16V R938 270k 1/16W IN1IN1+ V+ IN2+ IN3+ IN2- IN3- 9 10 11 12 13 14 1 OUT1 OUT2 OUT3 8 3.6 4.4 2.1 0.2 3.8 C931 1 10V 1 Q903 PN109F SW C930 2.2 6.3V H 3 2 1.5 D930 DNP319-1 D916 MA8082 3.8 3 G 3.6 IC902 µPC324G2-E2 R935 22k 4 D931 DNP319-1 Q931 DTC143TKA-T146 SW R934 4.7k R933 82 1/4W 5 C933 22 16V R932 82 1/4W 6 F R931 82 1/4W 7 R930 82 1/4W OUT4 IN4IN4+ V- 0.8 3.5 3.8 0.2 3.8 D905 1SS355 1 D912 MA8082 2 R925 910k 1/16W C905 22 10V C908 0.1 25V Q904 2SA1037AK-T146 SW B-SS3514<J..>-H(24) Schematic diagram 4-31 H board l 4-32 REMOTO 5V(STBY) KEY INPUT_KEY PW_KEY PW_LED1 PW_LED2 IN_LED1 IN_LED2 5V(SENS) GND SEN1 SEN2 SEN3 SEN4 LED_CTL VREF GND TO B BOARD CN501 (h) [ USER CONTROL ] — H BOARD (Component Side) — — H BOARD (Conductor Side) — H BOARD Terminal name of semiconductors in silk screen printed circuit (* ) Ref. * Q903, Q930, Q931 2 D905 - D916 3 *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 4-9) 4-33 4-34 4-36 SDT-P 26 25 SDT-GND 24 23 SDT-N 22 21 GND 20 SCL 19 SDA 18 CPU_ST 17 CN_SENS 16 15 14 AUDIO_L 13 AUDIO_GND 12 AUDIO_R 11 10 STBY_5V 9 12V 8 12V 7 12V 6 GND 5 GND 4 GND 3 AUDIO_12V 2 AUDIO_12V 1 TO A BOARD CN101 FG C484 39µ 16V C482 0.33 16V B C410 0.1 25V F FL1 FL404 6 5 4 3 2 1 R489 0.050 1/2W AUDIO12V C478 100µ 16V C409 100µ 16V 10 9 8 7 FL401 R497 0 C458 0.33µ 16V B R414 2.2k 1/10W R415 2.2k 1/10W R474 220 1/10W 11.7 S S S G D D D D IC410 SI4431DY-T1 CONTROL IC409 MAX1626ESA-TE2 DC-DC R440 100 1/16W 11.7 V+ REF CS SHDN EXT 3 /5 GND OUT Q401 DTC114EKA-T146 SW 0 R436 10k 1/16W 4.8 R475 220 1/10W 1 2 Ref. No. 3 CN401 26P 5 6 7 8 4 3 2 Circuit diagram division code 1 l 1 4 • Divided circuit diagram One sheet of U board circuit diagram is divided into two sheets, each having the code U-a to U-b. For example, the destination ab1 on the U-a sheet is connected to ab1 on the U-b sheet. 8 -a board D405 D3FS4A-TA 1.3 0 C450 0.33 16V B 4.8 2 1 C433 22 16V 4.5 4.5 3 4 C451 22 16V adj C460 100 6.3V L404 12µH C483 0.1 25V F R499 0 CTL 5 1.2 9V C444 4.7µ 10V B C446 4.7µ 10V B C486 100 6.3V C457 0.1 25V F R_OUT LOUD_L BIN_L C487 100 10V 1 C449 2.2 50V 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 D430 PTZ-TE25-6.2A C470 1000µ 10V C455 22µ 16V R433 8.2k 1/10W R452 0 C472 C452 1000µ 1000µ 10V 10V R448 0 SCK SI CSN FB413 FL403 2 2 1 5 6 4 3 3 4 5 6 C473 1000µ 10V R453 0 C416 1 50V C415 1 50V R454 0 C475 1.0p CK +5V A5V C427 6800p 25V B R423 330 1/10W C418 6800p 25V B R412 330 1/10W 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CN406 3P R427 560 1/10W C429 220p 50V CH C420 220p 50V CH SD5V R418 560 1/10W R424 R420 3.3k 10k 1/10W 1/10W C428 220p R426 50V 1M CH 1/10W C419 220p 50V CH R413 3.3k 1/10W R410 1M 1/10W R411 10k 1/10W CSN SCK SI GND GND GND GND GND GND GND GND 12V 12V 12V 12V 12V 12V STBY_5V STBY_5V SDA SCL CPU_ST SCK SI CSN MUTE HP_STAT DDON_U CN402 30P SDT-P SDT-GND SDT-N TO B BOARD CN502 ab22 ab21 ab19 ab18 ab17 ab16 ab15 ab14 ab13 ab12 ab11 ab9 ab7 ab5 ab3 ab1 ab20 ab10 ab8 ab6 ab4 ab2 11 1 FB3 FB3 2 FB412 0UH FB411 0UH 2 3 C445 0.068 16V B C439 0.068 16V B R449 0 R429 8.2k 1/10W Q409 2SK1828 BUFFER 4.5 C443 0.027 16V B VCC OUT GND IC412 BA05FP 5V REG 4.5 C454 0.33µ 16V B L_IN NC BOUT_L LOUD_R BIN_R L_OUT BOUT_R IN_R DGND GND TRE_R SDA TRE_L SCL VCC R439 6.2k 1/16W R493 100 1/16W 4.5 7.2 CREF NC R494 100 1/16W R485 10k 1/16W C438 0.027 16V B R484 10k 1/16W Q408 2SK1828 7.2 BUFFER IC403 TDA7315D013TR AUDIO PROCESS R491 39k 1/16W R490 10k 1/16W L405 27µH R438 1k 1/16W C448 2.2 50V 4.5 0 C437 2200p 16V SL 4.5 IC404 PQ20VZ5U 9V REG C459 0.33µ 16V B R435 4.7k 1/10W R434 4.7k 1/10W C432 100p 50V CH C436 2200p 16V SL 4.5 C431 0.1 25V F 12V STBY5V 9 10 8 7 7 8 9 10 1 FL402 3 2 1 10 7 U b 9 6 a IN TO B BOARD CN504 G Schematic diagram 8 5 F 1 4-35 7 OUT E 2 D 3 A 4 G 6 5 H 5 6 C 4 7 I 3 8 B 2 10 9 1 11 12 13 14 15 16 17 18 19 20 C474 1.0p CK (4) Schematic Diagrams of U Board 12 13 U -a (AUDIO) B-SS3514<J..>-U-a(24) ab2 ab7 ab6 ab10 ab5 0 IC402 LM4863MTEX POWER AMP OUT_A- VDD OUT_A+ GND SDOWN IN_B- OUT_B- BYPASS VDD OUT_B+ GND IN_A- HP_IN GND GND GND IN_B+ 0.2 2.4 2.5 2.5 2.5 STBY5V R405 100k 1/16W C414 100p 50V CH SD5V C464 0.1 50V (PPS) C467 0.1 50V R461 6.8k 1/10W (PPS) D421 MA111-TX 2.5 2.5 R463 47k C481 1000p 25V CH 8 6 5 R416 22k 1/10W 2 C456 100µ 16V R408 47k 1/10W R450 220k 1/16W 3 1 C471 100 10V R466 10k 1/16W R495 22k 1/16W C461 22µ 16V R483 300k 1/16W 4 NC DVSS SI SCK BSFT0 BSFT1 RESETN CSEL0 CSEL1 CSEL2 TSTSEL DVDD NC C412 0.1 25V F R464 R467 220k 10k 1/10W 1/16W (PPS) C468 0.1 50V R457 0 C423 1 50V C413 0.1 25V F R404 100k 1/16W 7 C407 R406 220p 10k 50V 1/16W CH IC401 YSS901 STEREO DIPOLE 1 C442 22p 50V CH 5.0 Q410 DTA123JKA S DOWN SW A5V R479 3.3k 1/16W C421 1 10V F R417 47k 1/16W R421 10k 1/16W R422 10k 1/16W R425 10k 1/16W C425 0.1 25V F C408 220p 50V CH R482 0 C403 100µ 16V C404 100µ 16V R472 120 1/8W R473 120 1/8W D403 MA111-TX 0 Q407 DTC323TKT146 MUTE 0 FG Q406 DTC323TKT146 0.1 MUTE 0 D431 MA3075WA-(TX) R486 0.3 10k 2.9 Q404 1/16W DTC114EKA-T146 SW (2012) R487 0 0 Q405 DTC114EKA-T146 D413 SW MA111-TX D414 MA111-TX R409 220k 1/16W D416 MA111-TX C462 10 16V R444 47k 1/16W destination ab1 on the U-a sheet is connected to ab1 on the U-b sheet. IC411 µPC393G2 AMP FB414 FB415 R442 47k 1/16W STBY5V R443 47k 1/16W C479 10 16V D415 MA111-TX IN B+ IN B- OUTB IN A- OUTA 1 V+ R477 10k 1/16W R478 10k 1/16W Q411 DTA123JKA SW R468 220k 1/16W 2 8 3 7 4 6 D417 MA111-TX 5 V- FB2 D420 MA111-TX D422 MA111-TX D404 MA111-TX 5.0 0 R492 10k 1/16W 5.0 5.0 5.0 5.0 0 6.8 D406 MA111-TX D5V 64 63 62 61 60 59 58 57 56 55 54 53 52 FB2 FB409 FB410 Circuit diagram division code IN A+ R432 680 1/16W C441 22p 50V CH 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 R430 1M 1/16W C453 0.1 25V F D5V Ref. No. D418 MA111-TX R441 47k 1/16W R488 220k 1/16W R455 220k 1/16W D419 MA111-TX R476 10k 1/16W C465 0.1 25V F 1 2 3 4 1 2 3 4 1 2 3 4 5 CN404 4P ROUT+ ROUT+ ROUTROUT- SPEAKER L SPEAKER R 1 HEADPHONE CN405 4P LOUT+ LOUT+ LOUTLOUT- CN403 5P B-SS3514<J..>-U-b(24) 1 b a R445 0 U -b (AUDIO) 2.5 2.5 2.5 2.5 IN_A+ GND R451 1k 1/16W 1/2VCC C406 220p 50V CH C480 47 16V R469 0 C411 0.1 25V F OUT1 VCC -IN1OUT2 +IN1-IN2 VEE +IN2 IC408 SD5V BA4560F-T1 HPF GND GND C417 0.1 50V STBY_5V C463 0.1 50V 2.5 (PPS) 11 12 13 14 15 16 17 18 19 20 19 18 17 16 15 14 13 12 11 10 9 AGND 8 R419 22k 1/10W 1 7 C422 1 50V R456 0 C466 0.1 50V R460 6.8k 1/10W 2.5 R462 47k (PPS) R465 220k 1/10W 2 6 R407 47k 1/10W AUDIO12V C469 0.1 50V (PPS) SD5V 3 5 ab4 ab3 ab1 ab8 ab9 ab11 ab12 ab13 2.3 2.3 2.4 2.4 2.3 2.3 2.4 4 NC TST2 DVSS AVSS AIRRET AIROUT AIR AILRET AILOUT AIL VREF AVDD NC R428 10k 1/16W 20 21 22 23 24 25 26 27 28 29 30 31 32 5 4-38 4-37 ab14 ab17 C426 10 16V C430 0.1 25V F C435 470p 50V CH XTAL DVSS TSTCK TST1 TSTNI TSTNO NC NC NC NC D 2.3 2.5 X401 2.8224MHz F 6 R480 R481 0 0 E 7 • U-b BOARD WAVEFORMS I 5.0 8 2.6 2.6 2.7 • Divided circuit diagram One sheet of U board circuit diagram is divided into two sheets, each having the code U-a to U-b. For example, the G 4.8 10 9 1 2 3 4 NC NC NC NC DVDD DSEL0 DSEL1 DSEL2 DIN DOUT CSN BCLK SYNCN CTLSEL DVDD NC NC NC NC NC NC NC NC LOUT ROUT PLLC AVSS EXTAL C C424 0.1 25V F C434 47 16V B ab15 ab16 ab18 ab19 ab21 ab22 H ab20 A 11 10 9 8 7 6 5 4 3 2 1 2.2 Vp-p (2.8224MHz) (u) [ AUDIO ] — U BOARD (Component Side) — — U BOARD (Conductor Side) — U BOARD Terminal name of semiconductors in silk screen printed circuit (* ) Ref. * Q401, Q404 - Q407 Q410, Q411 Q408, Q409 2 !£ D403 - D406 D413 - D422, D430 D431 3 !¡ *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 4-9) Schematic diagram Ò U -b board 4-39 4-40 (g) [ POWER SUPPLY, AUDIO IN ] — G BOARD (Conductor Side) — — G BOARD (Component Side) — G BOARD Terminal name of semiconductors in silk screen printed circuit (* ) Ref. * Q770, Q771 2 D708 - D710 3 D707, D711, D712 5 D767, D768 !¡ *: Refer to Terminal name of semiconductors in silk screen printed circuit (see page 4-9) 4-41 4-42 (5) Schematic Diagrams of G (P1-P2) Boards 1 3 2 4 5 6 7 8 10 9 11 12 14 13 A CN704 3P R731 3.9 10W C723 R701 1000p 680k 250V 1/2W E AC IN C729 1000p 250V E C730 0.0047 250V 1 3 R708 10k 1/10W C719 180 450V R704 2.2M 1/2W CHIP 3.1 1.4 R709 68k 1/10W C709 0.01 50V B CHIP R713 2.2M 1/2W CHIP 2.8 2.5 C R718 330k 1/10W OOB VIN DEM NC D704 1SS119-25TG 2 GND GND DRIVER NC ISENSE VAUX VCTRL DS LREF R707 10k 1/10W L703 47µH 2.6 0 CHIP 1 1 D707 RD10M-T1B2 D708 UDZ-TE-17-4.7B 2 CHIP C710 0.047 50V B CHIP CHIP CHIP R725 27k 1/10W C711 100 50V 5 10 4 11 3 12 2 13 1 C706 0.047 50V B 14 CHIP R705 3.9k 1/10W R706 1k 1/10W RN-CP RN-CP C708 0.022 50V B CHIP R719 15 1/2W R714 1k 1/10W 3 12V CN701 8P 2 8.8 C712 680p 50V B IC702 µPC1093J-1-T C713 47 50V D 2.5 1 CHIP D706 11ES2-TB5 C705 1500 16V R703 10k 1/10W CHIP PH701 PC123FY2 CHIP R727 220 1/10W 4 3 1 1 3 4 2 2 R722 1k 1/10W R723 2k 1/10W CHIP RN-CP 9.8 CHIP 2.8 8 7 6 5 4 3 2 1 GND GND GND GND 12V 12V 12V 12V TO A BOARD CN105 9 8 7 6 5 4 3 2 1 3.3V 3.3V GND GND 5V 5V GND GND DDON TO A BOARD CN104 8.8 C743 470 16V L704 47µH 12V C716 470 16V 3 C704 1500 16V R712 150 2W R717 0.22 2W R721 10 1/10W R724 1k 1/10W 9 R711 150 2W CHIP R726 150k 3 1/10W CHIP 6 1 R710 0 R716 470 1/10W 8 D705 D1NL20U-TR CHIP 2 C707 220p 1kV SL 3 132.5 NC D703 ERA34-10TP1 Q701 IRFIBC40G-LF38 SWITCHING 1 IC701 TEA1504/N2 PWM CONTROL 1 1 C727 0.1 2 250V 2 3 3 1 2 3 4 4 4 AC L NC AC N C701 0.1 250V 7 12V 2 5 FH701 C703 0.01 630V R702 100k 3W D701 D2SB60A 6 CN703 3P VDR701 T701 7.4MHz D702 D10SC9M 2 7 C724 0.0047 250V F701 B T702 TFM96455 R728 0.1 1/2W FH702 +12V 1 2 3 9 10 11 12 13 14 AC L OUT NC AC L IN 8 POWER 12V C717 0.1 25V F PS702 2A PS701 3.15A L707 22µH +3.3V L701 56µH 8 1 3.4 5 R730 0.068 1/2W L705 47µH SKIP PGND REF VL GND 8 9 10 11 12 13 14 RESET DL5 V+ TIME/ON5 SHDN SYNC DL3 SECFB 5 6 BST5 7 FB5 BST3 STEER LX3 FB3 DH3 CSL3 RUN/ON3 CSH3 C722 1 50V +5V R736 30k 1/16W R737 27k 1/16W 4.9 R735 470 1/10W L706 47µH R733 0.068 1/2W 3 3 2 L702 39µH 2 1 D711 MA3XD15001S0 1 D712 MA3XD15001S0 3.3V IC707 MMDF6N03HDR2 CONTROL G -P1 LX5 D710 MA2S728-TX 6 D_B2 D_B1 D_A2 D_A1 CSL5 7 2 G G_B S_B G_A S_A 8 4.7 3 4 C732 0.1 25V F DH5 4 R732 10 1/16W CSH5 2 F C726 470 16V C728 0.1 25V F SEQ 1 7 C721 0.1 25V F CN702 9P IC706 MAX1631EAI +5V/+3.3V REG D709 MA2S728-TX 6 D_A1 D_A2 D_B1 D_B2 28 27 26 25 24 23 22 21 20 19 18 17 16 15 4 7.0 S_A G_A S_B G_B 5 2 2.7 3 IC704 MMDF6N03HDR2 CONTROL 1 5V 3 E C737 470 16V C741 470 6.3V C738 470 16V C742 470 6.3V GND (POWER SUPPLY) C735 0.1 25V F C736 4.7 35V C740 C739 4.7 0.1 25V 25V F H B-SS3514<J..>-G-P1(24) Schematic diagram 4-43 G -P1 board l 4-44 1 3 2 4 5 6 7 8 10 9 11 12 14 13 A G R788 100 1/10W -P2 (AUDIO IN) R786 180 1/4W R780 180 1/4W R771 100k 1/10W AUDIO_L R773 100k 1/10W C791 1.0 50V Q771 3.7 2SC2712G BUFFER R779 2.2k 1/10W D 2 1 OUT1 VCC R782 0 R783 0 R791 47k 1/10W C794 R792100p 47k 1/10W C795 100p OUT2 +IN1 -IN2 VEE +IN2 7 -IN1 R796 47k 1/10W R795 47k 1/10W C797 0.1 25V D767 MA3075WA-(TX) R798 68k 1/10W C792 1.0 50V R784 0 R793 47k 1/10W R785 0 C796 100p R797 47k 1/10W R799 47k 1/10W GND E AUDIO_R AUDIO_GND AUDIO_L AUDIO_GND TO A BOARD CN106 12V 8 1 PS791 R794 47k 1/10W 9.0 4.3 R778 2.2k 1/10W R781 0 R790 47k 1/10W 3.7 R775 1k 1/10W C771 1 50V C790 1.0 50V 6 FB751 R774 1k 4.4 1/10W Q770 2SC2712G BUFFER C793 100p C772 100 16V 5 AUDIO_R CN706 3P AUDIO STEREO JACK R777 330 1/4W 9.0 2 FB750 R776 330 1/4W 3 C 2 3 1 C770 1 50V R789 100 1/10W IC790 µPC358G2-E2 BUFFER 4 AUDIO IN R772 100k 1/10W 1 2 3 4 12V B R770 100k 1/10W CN705 4P D768 MA3075WA-(TX) C798 100 16V B-SS3514<J..>-G-P2(24) 4-45 4-46 4-5. SEMICONDUCTORS AD9884-AKS-100S 102 XCB1456R M52758FP n 65 103 YSS901-F IRFIBC40G-LF38 51 33 52 64 MA3075WA-TX MA3130WA-TX D10SC9M 32 3 n 1 39 128 1 20 64 1 TOP VIEW 38 TOP VIEW 64 pin QFP TOP VIEW 1 36 pin DIP 2 1 19 TOP VIEW 12 G BA033FP-E2 BA05FP-E2 IS455J 1 D 3 3 2 2 S 1 3 UPC1093J-1-T PC123F2 PC123FY2 PN109F MA8082-H-TX D2SB60A-F04 4 ANODE 3 3 4 - - 2 1 ~ ~ - 1 1 2 3 BA4560F MAX1626ESA-TE2 MM1170BFB SN74CBTD3306PWR UPC358G2 UPC393G2 24LC21AT/SN 2 3 LM4863MTEX TDA7315D013TR PQ20VZ5U TOP VIEW 20 pin SOP MAX1631EAI-TG-068 1 3 1 4 1: FB 2: Vc 3: GND 4: Vsw 5: Vin TOP VIEW TC7S04FU(TE85R) TC74S08FU(TE85R) TC74S32FU(TE85R) 28 pin DIP 1 5 2 TOP VIEW 8 pin SOP MB90F553APF-G-BND DTA114EKA-T146 DTA123JKA-T146 DTA143XKA-T146 DTC114EK DTC114EKA-T146 DTC143TKA-T146 DTC323TK DTC323TKT146 2SA1037AK-T-146-QR 2SC2712G-TE85L 2SC2712-YG C B n BA7078AF-E2 80 E 51 81 50 n INDEX FZT853-TA 1 5 pin CHIP 1 D 1 3 D 5 4 S S ANODE 2 D 1 S 3 G 2 1 CATHODE 2SK1828 2SK1828TE85L SI4431DY-T1 DTZ4.7C MA111 RD12SB2 UCZ-TE-17-12B UCZ-TE-17-4.7B 1SS355TE-17 ERA34-10TP1 RGP02-20EL-6394 1SS119-25 11ES2 CATHODE CATHODE ANODE ANODE 30 18 pin SOP MMDF6N03HDR2 M24C16-MN6T n 1 n D 8 RE10M-B2 RE10M-T1B2 D3FS4A-TA MA2S728 PTZ-TE25-6.2A SI2301DS-T1 TOP VIEW TOP VIEW CHEETAH3 C 31 100 1 B E 2 n 1 CATHODE 1 n n 4 1 TC74HC4066AFT(EL) TC74VHCT14AFT(EL) TC74VHC04FT(EL) TC74VHC125FT(EL) TC74VHC86FT(EL) C ANODE AA1101W ANODE E CATHODE IRFIBC40 3 2 1 D1NL20U-TR 3 CATHODE n TOP VIEW CATHODE 8 pin DIP TOP VIEW MA151WK-TX 1SS184 B CATHODE MARK 2 1 240 pin QFP 1 MT48LC1M16A1TG-7S CXB1455R MA3XD15001S0 TOP VIEW TEA1504/N2 G D BRPG1201W CATHODE ANODE n 1 CATHODE S ANODE 50 pin DIP n TOP VIEW 14 pin SOP n NC 1 TOP VIEW 1 48 pin QFP TOP VIEW 14 pin DIP Schematic diagram Ò G -P2 board 4-47 4-48 SDM-N50 SECTION 5 NOTE: • Items with no part number and no description are not stocked because they are seldom required for routine service. • The construction parts of an assembled part are indicated with a collation number in the remark column. EXPLODED VIEWS • Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 5-1. DISPLAY 7-685-646-79 7-685-645-79 7-685-248-19 7-682-546-04 7-682-660-09 The components identified by mark ¡ are critical for safety. Replace only with part number specified. +BVTP 3X8 +BVTP 3X6 +KTP 3X12 +P 3X5 +PS 4X6 11 9 13 5 8 12 6 10 5 4 14 7 15 5 2 16 3 19 18 20 21 1 20 23 21 24 22 25 17 REF.NO. PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 DESCRIPTION REMARK REF.NO. PART NO. X-4037-530-3 COVER ASSY, FRONT * A-1375-200-A H BOARD, COMPLETE 4-074-707-01 EARTH (H) 1-803-900-11 LCD MODULE (TFT) 4-074-712-01 HOLDER, PANEL 1-900-251-29 HARENESS ASSY, BH1 * A-1136-059-A B BOARD, COMPLETE 4-639-967-01 SCREW, 0 PLATE SPECIAL HEAD 4-073-822-02 COVER, REAR 4-075-607-01 TAPPING SCREW 3X8 14 15 4-073-809-03 COVER (S), HINGE 4-073-816-02 COVER (F), HINGE 16 17 18 19 20 4-073-808-02 4-074-713-01 4-073-823-03 4-073-825-01 1-529-586-11 21 22 23 24 25 2-625-102-31 BOLT, HEXAGON M3 4-074-711-01 PLATE, INSULATION 4-073-824-01 HINGE, PANEL 26 5-1 DESCRIPTION COVER (R), HINGE LEG, RUBBER COVER, BASE HINGE, BASE SPEAKER (2.7CM) 4-073-810-03 HOLDER, SP 4-074-714-02 RUBBER, ENCLOSURE * A-1394-966-A U BOARD, COMPLETE 4-074-708-02 EARTH (U) 4-075-703-01 FOOT (B), RUBBER 4-076-246-01 COVER, CABLE REMARK SDM-N50 5-2. CHASSIS 7-685-648-79 7-682-545-01 7-685-144-11 The components identified by mark ¡ are critical for safety. Replace only with part number specified. +BVTP 3X12 +B 3X4 +PTP 3X5 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 54 53 52 58 56 51 57 59 60 61 55 REF.NO. PART NO. 51 52 53 54 55 DESCRIPTION REMARK REF.NO. PART NO. 1-572-434-31 SWITCH, SEESAW (AC PWOER) 56 56 57 58 59 ¡ 1-794-122-11 INLET, AC (WITH FILTER) 4-070-122-01 SCREW (HD15) 4-073-835-02 CASE (R) 4-073-836-02 CASE (L) 60 61 5-2 * 4-073-828-01 * 4-073-828-11 X-4037-532-2 4-073-814-01 ¡ 1-576-230-11 DESCRIPTION LABEL (B) (AEP) LABEL (W) (U/C) PLATE ASSY, CHASSIS GUIDE, LIGHT FUSE (H.B.C.) (3.15A/250V) * A-1316-500-A G BOARD, COMPLETE * A-1299-074-A A BOARD, COMPLETE REMARK 58 SDM-N50 5-3. PACKING MATERIALS The components identified by mark ¡ are critical for safety. Replace only with part number specified. 105 106 102 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 113 104 107 108 109 110 112 115 117 111 116 118 114 103 101 REF.NO. PART NO. 101 101 102 103 104 4-075-214-02 4-075-850-02 4-075-107-01 4-075-104-01 1-469-778-11 105 106 107 108 108 1-759-626-21 1-759-627-23 1-775-444-31 ¡ 1-765-718-11 ¡ 1-765-719-11 109 109 DESCRIPTION REMARK REF.NO. PART NO. INDIVIDUAL CARTON (U/C) INDIVIDUAL CARTON (AEP) BOARD, TOP BOARD (A), BOTTOM CLAMP, FERRITE DISK, UTILITY DISK, INFOEMATION CORD, CONNECTION CORD SET, POWER (U/C) CORDSET, POWER (AEP) 1-778-967-11 ADAPTOR, CONVERSION (U/C) 1-785-512-31 CONNECTORK D SUB (15P CHANGER) (AEP) 5-3 DESCRIPTION REMARK 110 111 111 1-790-860-11 CABLE ASSY (15PDSUB CONNECTOR) 3-868-361-13 MANUAL, INSTRUCTION (U/C) 3-868-361-22 MANUAL, INSTRUCTION (AEP) 112 113 114 115 116 X-4037-533-1 4-075-106-01 4-075-105-01 4-075-109-01 4-075-110-01 117 118 4-075-111-01 BAG, PROTECTION 4-075-112-01 BAG, PROTECTION STAND ASSY BOARD, MIDDLE BOARD (B), BOTTOM BAG, PROTECTION BAG, PROTECTION SDM-N50 The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. SECTION 6 (b) ELECTRICAL PARTS LIST REF.NO. PART NO. NOTE: DESCRIPTION REMARK identified REF.NO.byPART The components [ in NO. this manual have been carefully factoryselected for each set in order to satisfy regulations regarding X-ray radiation. Should replacement be required, replace only with the value originally used. The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. When indicating parts by reference number, please include the board name. REF.NO. PART NO. DESCRIPTION RESISTORS • All resistors are in ohms • F : nonflammable REMARK • Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • All variable and adjustable resistors have characteristic curve B, unless otherwise • CAPACITORS MF : µF noted. • COILS UH : µH DESCRIPTION REMARK REF.NO. PART NO. * A-1136-059-A B BOARD, COMPLETE **************************** <CAPACITOR> C503 C504 C506 C507 C508 1-162-919-11 1-162-919-11 1-115-467-11 1-162-970-11 1-164-156-11 CERAMIC CHIP 22PF CERAMIC CHIP 22PF CERAMIC CHIP 0.22UF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.1UF C509 C510 C511 C512 C513 1-164-156-11 1-164-156-11 1-162-927-11 1-164-156-11 1-162-927-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF C514 C515 C516 C517 C518 1-164-156-11 1-162-927-11 1-164-156-11 1-164-156-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF C520 C521 C522 C525 C527 1-104-913-11 1-164-156-11 1-164-156-11 1-104-851-11 1-128-705-11 TANTAL. CHIP 10UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF TANTAL. CHIP 10UF ELECT 100UF C601 C602 C603 C604 C605 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-128-694-91 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF TANTAL. CHIP 22UF C606 C608 C609 C610 C611 1-164-156-11 1-164-156-11 1-164-156-11 1-162-923-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 47PF CERAMIC CHIP 0.1UF C612 C613 C614 C615 C616 1-162-923-11 1-128-694-91 1-164-156-11 1-164-156-11 1-164-315-11 CERAMIC CHIP 47PF TANTAL. CHIP 22UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 470PF C617 C618 C619 C620 1-164-156-11 1-164-156-11 1-164-156-11 1-165-112-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.33UF 5.00% 5.00% 10.00% 10.00% 5.00% 5.00% 5.00% 20.00% 50V 50V 10V 25V 25V 25V 25V 50V 25V 50V 25V 50V 25V 25V 25V 20.00% 16V 25V 25V 10V 20% 25V 25V 25V 25V 10V 5.00% 5.00% 20% 5.00% 25V 25V 25V 50V 25V 50V 10V 25V 25V 50V 25V 25V 25V 16V DESCRIPTION REMARK C621 1-128-694-91 TANTAL. CHIP 22UF 20% 10V C622 C623 C626 C627 C628 1-104-913-11 1-164-156-11 1-135-599-21 1-164-156-11 1-135-599-21 TANTAL. CHIP 10UF CERAMIC CHIP 0.1UF ELECT 39UF CERAMIC CHIP 0.1UF ELECT 39UF 20.00% 20% 16V 25V 16V 25V 16V C629 C630 C631 C632 C652 1-164-156-11 1-135-595-21 1-135-595-21 1-128-705-11 1-131-616-11 CERAMIC CHIP 0.1UF ELECT 100UF ELECT 100UF ELECT 100UF MYLAR CHIP 0.12UF 20% 20% 25V 6.3V 6.3V 10% 100V C653 C655 C656 C657 C658 1-135-599-21 1-164-156-11 1-164-357-11 1-164-156-11 1-128-704-11 ELECT 39UF CERAMIC CHIP 0.1UF CERAMIC CHIP 1000PF CERAMIC CHIP 0.1UF ELECT 47UF 20% 16V 25V 50V 25V C659 1-164-156-11 CERAMIC CHIP 0.1UF 20% 5.00% 25V <CONNECTOR> CN501 1-691-356-21 CONNECTOR, FFC/FPC (ZIF) 18P CN502 1-793-913-21 PIN, CONNECTOR (WITH PWB) 3P CN503 * 1-695-223-21 PIN, CONNECTOR (SMD) 10P CN504 1-793-911-21 PIN, CONNECTOR (WITH PWB) 30P CN505 1-793-912-21 CONNECTOR, BOARD TO BOARD 60P CN507 * 1-766-311-21 PIN, CONNECTOR (PC BOARD) 2P CN508 * 1-766-311-21 PIN, CONNECTOR (PC BOARD) 2P <DIODE> D501 D502 D503 D601 D604 8-719-988-61 8-719-158-49 8-719-988-61 8-719-054-47 8-719-073-69 DIODE 1SS355TE-17 ZENER DIODE RD12SB2 DIODE 1SS355TE-17 DIODE D3FS4A-TA ZENER DIODE PTZ-TE25-6.2A <FERRITE BEAD> FB501 FB502 FB503 FB504 FB505 6-1 1-414-445-11 1-414-445-11 1-414-445-11 1-469-118-21 1-414-445-11 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH The components identified by mark ¡ are critical for safety. Replace only with part number specified. REF.NO. PART NO. SDM-N50 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK (b) REF.NO. PART NO. DESCRIPTION REMARK FB601 FB602 FB603 FB604 FB605 1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH R525 R533 R534 R535 R536 1-216-833-91 1-216-833-91 1-216-833-91 1-216-848-11 1-216-833-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 10K 10K 180K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W FB606 FB613 1-414-445-11 FERRITE 1-469-118-21 FERRITE 0UH 0UH R601 R604 R606 R607 R608 1-216-833-91 1-216-829-11 1-216-829-11 1-216-809-11 1-216-829-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 4.7K 4.7K 100 4.7K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W 0UH 0UH R609 R610 R611 R613 R615 1-216-829-11 1-216-829-11 1-218-710-91 1-218-672-11 1-218-668-11 RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 4.7K 5.6K 150 100 5% 5% 0.50% 0.50% 0.50% 1/16W 1/16W 1/16W 1/16W 1/16W R617 R619 R620 R624 R625 1-218-672-11 1-218-660-91 1-218-660-91 1-216-821-11 1-218-697-11 METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP 150 47 47 1K 1.6K 0.50% 0.50% 0.50% 5% 0.50% 1/16W 1/16W 1/16W 1/16W 1/16W R626 R631 R632 R633 R634 1-216-295-91 1-216-833-91 1-216-801-11 1-216-801-11 1-240-941-91 SHORT RES-CHIP RES-CHIP RES-CHIP METAL CHIP 0 10K 22 22 0.05 5% 5% 5% 1% 1/16W 1/16W 1/16W 1/2W R635 R651 R652 R653 R654 1-216-809-11 1-216-845-11 1-218-272-11 1-220-264-11 1-220-264-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100 100K 5.1K 1K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/4W 1/4W R655 R656 R657 R658 R659 1-220-264-11 1-220-264-11 1-216-295-91 1-216-295-91 1-216-295-91 RES-CHIP RES-CHIP SHORT SHORT SHORT 1K 1K 0 0 0 5% 5% 1/4W 1/4W R663 R664 R665 R666 R667 1-218-698-11 1-218-725-11 1-218-734-11 1-220-397-11 1-216-840-11 METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 1.8K 24K 56K 4.7M 39K 0.50% 5% 0.50% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R668 R669 R670 R671 R672 1-216-833-91 1-211-899-11 1-211-899-11 1-216-837-11 1-216-840-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 0.22 0.22 22K 39K 5% 10% 10% 5% 5% 1/16W 1/4W 1/4W 1/16W 1/16W <FILTER> FL601 FL602 FL603 1-469-461-21 FERRITE 1-469-461-21 FERRITE 1-234-498-21 FILTER, EMI <IC> IC501 IC503 IC601 IC602 IC603 8-759-654-97 8-759-162-80 8-752-088-88 8-759-259-77 8-759-485-63 IC MB90F553APF-G-BND-AP02 IC MM1170BFB IC CXB1456R IC PQ20VZ5U IC MAX1626ESA-TE2 IC604 IC651 8-729-045-53 TRANSISTOR SI4431DY-T1 8-759-100-93 IC uPC393G2 <COIL> L601 L651 L652 L653 1-419-424-21 1-419-424-21 1-419-424-21 1-419-426-21 INDUCTOR 47UH INDUCTOR 47UH INDUCTOR 47UH INDUCTOR 22UH <IC LINK> PS651 ¡ 1-533-999-21 FUSE, (SMD) (2.0A) <TRANSISTOR> Q501 Q601 Q602 Q651 Q652 8-729-900-53 8-729-900-53 8-729-046-75 8-729-900-53 8-729-027-36 TRANSISTOR DTC114EK TRANSISTOR DTC114EK TRANSISTOR SI2301DS-T1 TRANSISTOR DTC114EK TRANSISTOR DTA143XKA-T146 Q653 Q654 8-729-051-52 TRANSISTOR FZT853-TA 8-729-051-52 TRANSISTOR FZT853-TA <RESISTOR> <NETWORK RESISTOR> R501 R502 R503 R507 R508 1-216-833-91 1-216-833-91 1-216-833-91 1-216-809-11 1-216-809-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 10K 10K 100 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R509 R510 R518 R519 R520 1-216-821-11 1-216-833-91 1-216-833-91 1-216-833-91 1-216-833-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 10K 10K 10K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W RA501 RA502 1-239-412-11 NETWORK RESISTOR (CHIP) 100 1-239-412-11 NETWORK RESISTOR (CHIP) 100 <FERRITE> RFB602 RFB603 RFB604 RFB605 6-2 1-469-312-21 1-469-312-21 1-469-312-21 1-469-312-21 ARRAY, FERRITE CHIP ARRAY, FERRITE CHIP ARRAY, FERRITE CHIP ARRAY, FERRITE CHIP SDM-N50 (b)(h) REF.NO. PART NO. The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK REF.NO. PART NO. RFB606 1-469-312-21 ARRAY, FERRITE CHIP DESCRIPTION REMARK <IC> RFB607 1-469-312-21 ARRAY, FERRITE CHIP IC901 IC902 8-759-189-86 IC IS455J 8-759-100-95 IC uPC324G2 <TRANSFORMER> <TRANSISTOR> T651 T652 1-435-299-11 TRANSFORMER, INVERTER (SMD) 1-435-299-11 TRANSFORMER, INVERTER (SMD) Q903 Q904 Q930 Q931 <CRYSTAL> X501 8-729-051-44 8-729-026-49 8-729-027-56 8-729-027-56 TRANSISTOR PN109F TRANSISTOR 2SA1037AK-T146-R TRANSISTOR DTC143TKA-T146 TRANSISTOR DTC143TKA-T146 1-767-340-11 VIBRATOR, CRYSTAL <RESISTOR> R902 R903 R904 R905 R906 1-216-819-11 1-218-701-11 1-216-819-11 1-216-819-11 1-216-827-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 680 2.4K 680 680 3.3K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R907 R908 R909 R910 R911 1-216-820-11 1-216-823-11 1-216-826-11 1-216-832-11 1-216-854-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 820 1.5K 2.7K 8.2K 560K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R925 R930 R931 R932 R933 1-202-931-11 1-220-257-91 1-220-257-91 1-220-257-91 1-220-257-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 910K 82 82 82 82 5% 5% 5% 5% 5% 1/16W 1/4W 1/4W 1/4W 1/4W <CONNECTOR> R934 R935 R938 R939 R940 1-216-829-11 1-216-837-11 1-216-850-11 1-216-835-11 1-216-853-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 4.7K 22K 270K 15K 470K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W 1-691-356-21 CONNECTOR, FFC/FPC (ZIF) 18P R941 1-216-845-11 RES-CHIP 100K 5% 1/16W ******************************************************************************* * A-1375-200-A H BOARD, COMPLETE **************************** <CAPACITOR> C901 C902 C903 C905 C908 1-162-970-11 1-119-751-11 1-119-751-11 1-104-852-11 1-164-156-11 CERAMIC CHIP 0.01UF TANTAL. CHIP 22UF TANTAL. CHIP 22UF TANTAL. CHIP 22UF CERAMIC CHIP 0.1UF 10.00% 20.00% 20.00% 20.00% 25V 16V 16V 10V 25V C930 C931 C933 C934 1-125-838-91 1-109-982-11 1-119-751-11 1-107-826-91 CERAMIC CHIP 2.2UF CERAMIC CHIP 1UF TANTAL. CHIP 22UF CERAMIC CHIP 0.1UF 10% 10.00% 20.00% 10.00% 6.3V 10V 16V 16V CN901 <DIODE> <SWITCH> D901 D902 D903 D905 D906 8-719-991-97 8-719-951-14 8-719-951-14 8-719-988-61 8-719-422-89 DIODE BRPG1201W DIODE AA1101W DIODE AA1101W DIODE 1SS355TE-17 ZENER DIODE MA8082-H-TX S901 S902 S903 S904 S905 1-771-855-21 1-771-855-21 1-771-855-21 1-771-855-21 1-771-855-21 D907 D908 D909 D910 D911 8-719-422-89 8-719-422-89 8-719-422-89 8-719-422-89 8-719-422-89 ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX S906 S907 1-771-855-21 SWITCH, KEYBOARD (INPUT) 1-771-855-21 SWITCH, KEYBOARD (MENU) D912 D913 D914 D915 D916 8-719-422-89 8-719-422-89 8-719-422-89 8-719-422-89 8-719-422-89 ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX D930 D931 8-719-079-68 DIODE DNP319-1 8-719-079-68 DIODE DNP319-1 SWITCH, KEYBOARD (POWER) SWITCH, KEYBOARD (-) SWITCH, KEYBOARD (+) SWITCH, KEYBOARD (DOWN) SWITCH, KEYBOARD (UP) ******************************************************************************* 6-3 The components identified by mark ¡ are critical for safety. Replace only with part number specified. REF.NO. PART NO. SDM-N50 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK (u) REF.NO. PART NO. * A-1394-966-A U BOARD, COMPLETE **************************** 4-075-598-01 PAN HEAD SCREW M1.6 DESCRIPTION REMARK C455 1-126-395-11 ELECT CHIP 22UF 20.00% 16V C456 C457 C458 C459 C460 1-117-681-11 1-164-156-11 1-110-501-11 1-110-501-11 1-135-595-21 ELECT CHIP 100UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.33UF CERAMIC CHIP 0.33UF ELECT 100UF 20.00% 16V 25V 16V 16V 6.3V C461 C462 C463 C464 C465 1-126-395-11 1-124-779-00 1-117-749-11 1-117-749-11 1-164-156-11 ELECT CHIP 22UF ELECT CHIP 10UF FILM CHIP 0.1UF FILM CHIP 0.1UF CERAMIC CHIP 0.1UF 20.00% 20.00% 20.00% 20.00% 16V 16V 50V 50V 25V C466 C467 C468 C469 C470 1-117-749-11 1-117-749-11 1-117-749-11 1-117-749-11 1-128-835-91 FILM CHIP FILM CHIP FILM CHIP FILM CHIP ELECT 0.1UF 0.1UF 0.1UF 0.1UF 1000UF 20.00% 20.00% 20.00% 20.00% 20% 50V 50V 50V 50V 10V C471 C472 C473 C474 C475 1-128-995-21 1-128-835-91 1-128-835-91 1-162-905-11 1-162-905-11 ELECT CHIP 100UF ELECT 1000UF ELECT 1000UF CERAMIC CHIP 1PF CERAMIC CHIP 1PF 20% 20% 20% 0.25PF 0.25PF 10V 10V 10V 50V 50V C478 C479 C480 C481 C482 1-117-681-11 1-124-779-00 1-126-204-11 1-115-416-11 1-110-501-11 ELECT CHIP 100UF ELECT CHIP 10UF ELECT CHIP 47UF CERAMIC CHIP 1000PF CERAMIC CHIP 0.33UF 20.00% 20.00% 20.00% 5.00% 10.00% 16V 16V 16V 25V 16V C483 C484 C486 C487 1-164-156-11 1-135-599-21 1-135-595-21 1-128-995-21 CERAMIC CHIP 0.1UF ELECT 39UF ELECT 100UF ELECT CHIP 100UF 20% 20% 20% 25V 16V 6.3V 10V 10.00% 10.00% 20% <CAPACITOR> C403 C404 C406 C407 C408 1-117-681-11 1-117-681-11 1-164-230-11 1-164-230-11 1-164-230-11 ELECT CHIP 100UF ELECT CHIP 100UF CERAMIC CHIP 220PF CERAMIC CHIP 220PF CERAMIC CHIP 220PF 20.00% 20.00% 5.00% 5.00% 5.00% 16V 16V 50V 50V 50V C409 C410 C411 C412 C413 1-117-681-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 ELECT CHIP 100UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF 20.00% 16V 25V 25V 25V 25V C414 C415 C416 C417 C418 1-162-927-11 1-126-193-11 1-126-193-11 1-126-187-11 1-162-969-11 CERAMIC CHIP 100PF ELECT CHIP 1UF ELECT CHIP 1UF ELECT CHIP 0.1UF CERAMIC CHIP 0.0068UF 5.00% 20.00% 20.00% 20.00% 10.00% 50V 50V 50V 50V 25V C419 C420 C421 C422 C423 1-164-230-11 1-164-230-11 1-115-156-11 1-126-193-11 1-126-193-11 CERAMIC CHIP 220PF CERAMIC CHIP 220PF CERAMIC CHIP 1UF ELECT CHIP 1UF ELECT CHIP 1UF 5.00% 5.00% 20.00% 20.00% 50V 50V 10V 50V 50V C424 C425 C426 C427 C428 1-164-156-11 1-164-156-11 1-124-779-00 1-162-969-11 1-164-230-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF ELECT CHIP 10UF 20.00% CERAMIC CHIP 0.0068UF 10.00% CERAMIC CHIP 220PF 5.00% 25V 25V 16V 25V 50V C429 C430 C431 C432 C433 1-164-230-11 1-164-156-11 1-164-156-11 1-162-927-11 1-126-395-11 CERAMIC CHIP 220PF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF ELECT CHIP 22UF 5.00% 5.00% 20.00% 50V 25V 25V 50V 16V C434 C435 C436 C437 C438 1-126-204-11 1-164-315-11 1-164-676-11 1-164-676-11 1-104-700-11 ELECT CHIP 47UF CERAMIC CHIP 470PF CERAMIC CHIP 2200PF CERAMIC CHIP 2200PF CERAMIC CHIP 0.027UF 20.00% 5.00% 5.00% 5.00% 10.00% 16V 50V 16V 16V 16V C439 C441 C442 C443 C444 1-110-563-11 1-162-919-11 1-162-919-11 1-104-700-11 1-115-566-11 CERAMIC CHIP 0.068UF CERAMIC CHIP 22PF CERAMIC CHIP 22PF CERAMIC CHIP 0.027UF CERAMIC CHIP 4.7UF 10.00% 5.00% 5.00% 10.00% 10.00% 16V 50V 50V 16V 10V D403 D404 D405 D406 D413 8-719-073-01 8-719-073-01 8-719-054-47 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE D3FS4A-TA DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 C445 C446 C448 C449 C450 1-110-563-11 1-115-566-11 1-126-601-11 1-126-601-11 1-110-501-11 CERAMIC CHIP 0.068UF CERAMIC CHIP 4.7UF ELECT CHIP 2.2UF ELECT CHIP 2.2UF CERAMIC CHIP 0.33UF 10.00% 10.00% 20.00% 20.00% 10.00% 16V 10V 50V 50V 16V D414 D415 D416 D417 D418 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 C451 C452 C453 C454 1-126-395-11 1-128-835-91 1-164-156-11 1-110-501-11 ELECT CHIP 22UF ELECT 1000UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.33UF 20.00% 20% 16V 10V 25V 16V D419 D420 D421 D422 8-719-073-01 8-719-073-01 8-719-073-01 8-719-073-01 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 DIODE MA111-(K8).S0 <CONNECTOR> 10.00% CN401 1-794-071-21 CN402 1-793-911-21 CN403 1-695-514-21 CN404 * 1-580-057-11 CN405 * 1-580-057-11 CN406 CONNECTOR, INTERFACE 26P PIN, CONNECTOR (WITH PWB) 30P JACK (SMALL TYPE) 1P PIN, CONNECTOR (SMD) 4P PIN, CONNECTOR (SMD) 4P 1-793-913-21 PIN, CONNECTOR (WITH PWB) 3P <DIODE> 6-4 SDM-N50 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. (u) REF.NO. PART NO. DESCRIPTION REMARK D430 8-719-073-69 ZENER DIODE PTZ-TE25-6.2A D431 8-719-421-59 DIODE MA3130WA-TX REF.NO. PART NO. The components identified by mark ¡ are critical for safety. Replace only with part number specified. DESCRIPTION REMARK R409 R410 R411 R412 R413 1-216-849-11 1-218-776-11 1-216-675-11 1-216-639-11 1-216-663-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 220K 1M 10K 330 3.3K 5% 5% 5% 5% 5% 1/16W 1/10W 1/10W 1/10W 1/10W R414 R415 R416 R417 R418 1-216-659-11 1-216-659-11 1-216-683-11 1-216-841-11 1-240-068-21 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 2.2K 2.2K 22K 47K 560 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/16W 1/10W R419 R420 R421 R422 R423 1-216-683-11 1-216-675-11 1-216-833-91 1-216-833-91 1-216-639-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 22K 10K 10K 10K 330 5% 5% 5% 5% 5% 1/10W 1/10W 1/16W 1/16W 1/10W R424 R425 R426 R427 R428 1-216-663-11 1-216-833-91 1-218-776-11 1-240-068-21 1-216-833-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 3.3K 10K 1M 560 10K 5% 5% 5% 5% 5% 1/10W 1/16W 1/10W 1/10W 1/16W R429 R430 R432 R433 R434 1-240-082-21 1-216-857-11 1-216-819-11 1-240-082-21 1-240-079-21 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 8.2K 1M 680 8.2K 4.7K 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/10W 1/10W R435 R436 R438 R439 R440 1-240-079-21 1-216-833-91 1-216-821-11 1-218-711-11 1-216-809-11 RES-CHIP RES-CHIP RES-CHIP METAL CHIP RES-CHIP 4.7K 10K 1K 6.2K 100 5% 5% 5% 0.50% 5% 1/10W 1/16W 1/16W 1/16W 1/16W R441 R442 R443 R444 R445 1-216-841-11 1-216-841-11 1-216-841-11 1-216-841-11 1-216-295-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP SHORT 47K 47K 47K 47K 0 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W R448 R449 R450 R451 R452 1-216-295-91 1-216-295-91 1-216-849-11 1-216-821-11 1-216-864-11 SHORT SHORT RES-CHIP RES-CHIP SHORT 0 0 220K 1K 0 5% 5% 1/16W 1/16W R453 R454 R455 R456 R457 1-216-864-11 1-216-864-11 1-216-849-11 1-216-295-91 1-216-295-91 SHORT SHORT RES-CHIP SHORT SHORT 0 0 220K 0 0 5% 1/16W R460 R461 R462 R463 R464 1-240-081-21 1-240-081-21 1-240-091-21 1-240-091-21 1-240-099-21 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 6.8K 6.8K 47K 47K 220K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R465 R466 R467 R468 R469 1-240-099-21 1-216-833-91 1-216-833-91 1-216-849-11 1-216-295-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP SHORT 220K 10K 10K 220K 0 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W R472 1-240-129-21 RES-CHIP 120 5% 1/8W <FERRITE BEAD> FB409 FB410 FB411 FB412 FB413 1-414-445-11 1-414-445-11 1-469-324-21 1-469-324-21 1-469-118-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB414 FB415 1-414-760-21 FERRITE 1-414-760-21 FERRITE 0UH 0UH <FILTER> FL401 FL402 FL403 FL404 1-469-461-21 1-469-461-21 1-469-461-21 1-234-498-21 FERRITE FERRITE FERRITE FILTER, EMI 0UH 0UH 0UH <IC> IC401 IC402 IC403 IC404 IC408 8-759-650-06 8-759-596-49 8-759-273-12 8-759-259-77 8-759-924-46 IC YSS901-F IC LM4863MTEX IC TDA7315D013TR IC PQ20VZ5U IC BA4560F IC409 IC410 IC411 IC412 8-759-485-63 8-729-045-53 8-759-100-93 8-759-460-74 IC MAX1626ESA-TE2 TRANSISTOR SI4431DY-T1 IC uPC393G2 IC BA05FP-E2 <COIL> L404 L405 1-412-526-11 INDUCTOR 12UH 1-412-530-31 INDUCTOR 27UH <TRANSISTOR> Q401 Q404 Q405 Q406 Q407 8-729-900-53 8-729-900-53 8-729-900-53 8-729-015-39 8-729-015-39 TRANSISTOR DTC114EK TRANSISTOR DTC114EK TRANSISTOR DTC114EK TRANSISTOR DTC323TK TRANSISTOR DTC323TK Q408 Q409 Q410 Q411 8-729-025-28 8-729-025-28 8-729-027-29 8-729-027-29 TRANSISTOR 2SK1828 TRANSISTOR 2SK1828 TRANSISTOR DTA123JKA-T146 TRANSISTOR DTA123JKA-T146 <RESISTOR> R404 R405 R406 R407 R408 1-216-845-11 1-216-845-11 1-216-833-91 1-240-091-21 1-240-091-21 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100K 100K 10K 47K 47K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/10W 1/10W 6-5 The components identified by mark ¡ are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK (u)(a) REF.NO. PART NO. R473 R474 R475 R476 1-240-129-21 1-240-063-21 1-240-063-21 1-216-833-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP 120 220 220 10K 5% 5% 5% 5% 1/8W 1/10W 1/10W 1/16W R477 R478 R479 R480 R481 1-216-833-91 1-216-833-91 1-216-827-11 1-216-295-91 1-216-295-91 RES-CHIP RES-CHIP RES-CHIP SHORT SHORT 10K 10K 3.3K 0 0 5% 5% 5% 1/16W 1/16W 1/16W R482 R483 R484 R485 R486 1-216-295-91 1-218-751-11 1-216-833-91 1-216-833-91 1-216-833-91 SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP 0 300K 10K 10K 10K 5% 5% 5% 5% R487 R488 R489 R490 R491 1-216-295-91 1-216-849-11 1-240-941-91 1-216-833-91 1-216-840-11 SHORT RES-CHIP METAL CHIP RES-CHIP RES-CHIP 0 220K 0.05 10K 39K R492 R493 R494 R495 R497 1-216-833-91 1-216-809-11 1-216-809-11 1-216-837-11 1-216-295-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP SHORT 10K 100 100 22K 0 R499 1-216-295-91 SHORT DESCRIPTION REMARK C123 C124 C125 C126 C127 1-164-156-11 1-162-970-11 1-164-156-11 1-164-156-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF C128 C129 C130 C131 C132 1-164-156-11 1-162-927-11 1-164-156-11 1-164-156-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF 1/16W 1/16W 1/16W 1/16W C133 C134 C201 C203 C204 1-104-606-11 1-162-970-11 1-113-642-11 1-162-970-11 1-164-156-11 ELECT CHIP 150UF CERAMIC CHIP 0.01UF TANTAL. CHIP 47UF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.1UF 20.00% 10.00% 20.00% 10.00% 10V 25V 10V 25V 25V 5% 1% 5% 5% 1/16W 1/2W 1/16W 1/16W C205 C206 C207 C208 C209 1-128-993-21 1-164-156-11 1-113-642-11 1-104-606-11 1-162-970-11 ELECT CHIP 22UF CERAMIC CHIP 0.1UF TANTAL. CHIP 47UF ELECT CHIP 150UF CERAMIC CHIP 0.01UF 20% 10V 25V 10V 10V 25V 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W C210 C211 C212 C213 C214 1-164-156-11 1-164-156-11 1-164-156-11 1-113-642-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF TANTAL. CHIP 47UF CERAMIC CHIP 0.1UF C215 C216 C217 C218 C219 1-164-156-11 1-162-970-11 1-164-156-11 1-164-156-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF C220 C221 C222 C223 C224 1-113-642-11 1-162-970-11 1-164-156-11 1-113-642-11 1-162-970-11 TANTAL. CHIP 47UF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.1UF TANTAL. CHIP 47UF CERAMIC CHIP 0.01UF 20.00% 10.00% C225 C226 C230 C233 C234 1-113-642-11 1-162-970-11 1-164-156-11 1-164-156-11 1-135-210-11 TANTAL. CHIP 47UF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF TANTAL. CHIP 4.7UF 20.00% 10.00% C235 C236 C237 C238 C239 1-164-156-11 1-164-346-11 1-125-891-11 1-164-156-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 1UF CERAMIC CHIP 0.47UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF C240 C241 C242 C243 C244 1-164-156-11 1-164-156-11 1-162-927-11 1-164-156-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF C245 C246 C247 C248 C249 1-128-993-21 1-164-346-11 1-125-891-11 1-164-346-11 1-125-891-11 ELECT CHIP 22UF CERAMIC CHIP 1UF CERAMIC CHIP 0.47UF CERAMIC CHIP 1UF CERAMIC CHIP 0.47UF C250 1-164-156-11 CERAMIC CHIP 0.1UF 10.00% 5.00% 20.00% 20.00% 10.00% 20.00% 25V 25V 25V 25V 25V 25V 50V 25V 25V 25V 25V 25V 25V 10V 25V 0 <CRYSTAL> X401 SDM-N50 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 1-781-713-21 VIBRATOR, CERAMIC ******************************************************************************* * A-1299-074-A A BOARD, COMPLETE **************************** 4-075-598-01 PAN HEAD SCREW M1.6 10.00% 20.00% 10.00% 20.00% 25V 25V 25V 25V 25V 10V 25V 25V 10V 25V 10V 25V 25V 25V 10V <CAPACITOR> C101 C102 C103 C104 C105 1-164-156-11 1-162-919-11 1-162-919-11 1-162-927-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 22PF CERAMIC CHIP 22PF CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF C106 C107 C108 C109 C110 1-164-156-11 1-162-927-11 1-162-970-11 1-162-970-11 1-104-606-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.01UF ELECT CHIP 150UF C111 C112 C113 C114 C120 1-164-156-11 1-164-156-11 1-104-606-11 1-164-156-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF ELECT CHIP 150UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF 5.00% 5.00% 5.00% 5.00% 10.00% 10.00% 20.00% 20.00% 25V 50V 50V 50V 25V 25V 50V 25V 25V 10V 25V 25V 10V 25V 25V 6-6 10.00% 25V 16V 10V 25V 25V 5.00% 25V 25V 50V 25V 25V 20% 10.00% 10.00% 10V 16V 10V 16V 10V 25V SDM-N50 The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. (a) REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. C251 C254 C259 C260 1-164-156-11 1-110-563-11 1-164-156-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.068UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF C268 C276 C278 C279 C280 1-162-927-11 1-164-156-11 1-164-156-11 1-110-563-11 1-164-156-11 CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.068UF CERAMIC CHIP 0.1UF C281 C282 C283 C284 C285 1-164-156-11 1-110-563-11 1-164-156-11 1-162-927-11 1-164-357-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.068UF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF CERAMIC CHIP 1000PF C287 C288 C289 C290 C291 1-128-993-21 1-164-156-11 1-164-156-11 1-164-156-11 1-162-970-11 ELECT CHIP 22UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.01UF C292 C293 C294 C295 C296 1-115-467-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 CERAMIC CHIP 0.22UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF C297 C298 C299 C301 C302 1-164-156-11 1-164-156-11 1-164-156-11 1-128-993-21 1-162-927-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF ELECT CHIP 22UF CERAMIC CHIP 100PF C303 C304 C305 C306 C307 1-162-970-11 1-128-993-21 1-164-156-11 1-128-993-21 1-164-156-11 CERAMIC CHIP 0.01UF ELECT CHIP 22UF CERAMIC CHIP 0.1UF ELECT CHIP 22UF CERAMIC CHIP 0.1UF 10.00% 20% C308 C309 C310 C311 C312 1-162-927-11 1-164-156-11 1-162-927-11 1-164-156-11 1-162-927-11 CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF 5.00% C313 C314 C315 C316 C317 1-164-156-11 1-162-927-11 1-164-156-11 1-128-993-21 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF ELECT CHIP 22UF CERAMIC CHIP 0.1UF C318 C319 C320 C321 C322 1-128-993-21 1-162-927-11 1-162-927-11 1-162-970-11 1-164-156-11 ELECT CHIP 22UF CERAMIC CHIP 100PF CERAMIC CHIP 100PF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.1UF 20% 5.00% 5.00% 10.00% 10V 50V 50V 25V 25V C327 C328 C329 C330 C331 1-162-927-11 1-164-156-11 1-164-156-11 1-164-357-11 1-164-156-11 CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 1000PF CERAMIC CHIP 0.1UF 5.00% 50V 25V 25V 50V 25V C332 C333 1-162-927-11 CERAMIC CHIP 100PF 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 5.00% 10.00% 10.00% 5.00% 5.00% 20% 10.00% 10.00% 20% 5.00% 20% 5.00% 5.00% 5.00% 20% 25V 16V 25V 25V 50V 25V 25V 16V 25V 25V 16V 25V 50V 50V 10V 25V 25V 25V 25V 10V 25V 25V 25V 25V 25V 25V 25V 10V 50V 25V 10V 25V 10V 25V 50V 25V 50V 25V 50V 25V 50V 25V 10V 25V DESCRIPTION REMARK C334 C335 C336 1-164-156-11 CERAMIC CHIP 0.1UF 1-164-156-11 CERAMIC CHIP 0.1UF 1-164-156-11 CERAMIC CHIP 0.1UF 25V 25V 25V C337 C338 C339 C340 C341 1-164-357-11 1-128-993-21 1-164-156-11 1-164-156-11 1-162-927-11 CERAMIC CHIP 1000PF ELECT CHIP 22UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF C342 C343 C344 C345 C346 1-162-927-11 1-162-927-11 1-162-970-11 1-164-156-11 1-164-357-11 CERAMIC CHIP 100PF CERAMIC CHIP 100PF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.1UF CERAMIC CHIP 1000PF C347 C348 C349 C350 C351 1-164-156-11 1-164-156-11 1-128-993-21 1-164-357-11 1-128-993-21 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF ELECT CHIP 22UF CERAMIC CHIP 1000PF ELECT CHIP 22UF C352 C353 C354 C355 C356 1-128-993-21 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 ELECT CHIP 22UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF C357 C358 C359 C360 C361 1-164-156-11 1-164-156-11 1-128-993-21 1-115-412-11 1-164-156-11 CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF ELECT CHIP 22UF CERAMIC CHIP 680PF CERAMIC CHIP 0.1UF C362 C364 C365 C366 C367 1-162-970-11 1-164-156-11 1-164-156-11 1-126-200-11 1-164-156-11 CERAMIC CHIP 0.01UF CERAMIC CHIP 0.1UF CERAMIC CHIP 0.1UF ELECT CHIP 10UF CERAMIC CHIP 0.1UF 10.00% C368 C369 C370 C371 C372 1-162-927-11 1-164-156-11 1-162-927-11 1-162-927-11 1-164-156-11 CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF 5.00% C373 C374 C375 C376 C377 1-162-927-11 1-164-156-11 1-162-927-11 1-216-864-11 1-216-864-11 CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF CERAMIC CHIP 100PF SHORT 0 SHORT 0 5.00% 5.00% 50V 25V 50V C380 C381 C382 C383 1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11 CERAMIC CHIP 100PF CERAMIC CHIP 100PF CERAMIC CHIP 100PF CERAMIC CHIP 100PF 5.00% 5.00% 5.00% 5.00% 50V 50V 50V 50V 5.00% 20% 5.00% 5.00% 5.00% 10.00% 5.00% 50V 50V 25V 25V 50V 20% 5.00% 20% 25V 25V 10V 50V 10V 20% 20% 5.00% 20.00% 5.00% 5.00% <CONNECTOR> 5.00% 5.00% 10.00% 50V 25V CN101 1-794-071-21 CN102 1-793-183-11 CN103 1-793-183-11 CN104 * 1-766-376-11 CN105 * 1-691-591-11 CN106 6-7 50V 10V 25V 25V 50V CONNECTOR, INTERFACE 26P CONNECTOR, D SUB 15P CONNECTOR, D SUB 15P PIN, CONNECTOR (1.5MM)(SMD) 9P PIN, CONNECTOR (1.5MM) (SMD)8P 1-573-290-21 PIN, CONNECTOR (1.5MM) (SMD)4P 10V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V 25V 35V 25V 50V 25V 50V 50V 25V The components identified by mark ¡ are critical for safety. Replace only with part number specified. REF.NO. PART NO. DESCRIPTION REMARK CN107 * 1-580-789-21 PIN, CONNECTOR (SMD) 6P CN108 * 1-695-223-21 PIN, CONNECTOR (SMD) 10P <DIODE> D001 D002 D003 D004 D101 8-719-801-78 8-719-801-78 8-719-801-78 8-719-801-78 8-719-991-97 DIODE 1SS184 DIODE 1SS184 DIODE 1SS184 DIODE 1SS184 DIODE BRPG1201W D102 D103 D104 D105 D207 8-719-801-78 8-719-988-61 8-719-158-49 8-719-801-78 8-719-988-61 DIODE 1SS184 DIODE 1SS355TE-17 ZENER DIODE RD12SB2 DIODE 1SS184 DIODE 1SS355TE-17 D208 D209 D210 D211 D212 8-719-421-59 8-719-421-59 8-719-421-59 8-719-421-59 8-719-421-59 DIODE MA3130WA-TX DIODE MA3130WA-TX DIODE MA3130WA-TX DIODE MA3130WA-TX DIODE MA3130WA-TX D213 D214 D215 D216 D217 8-719-421-59 8-719-422-89 8-719-422-89 8-719-422-89 8-719-422-89 DIODE MA3130WA-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX D218 D219 D220 D221 D222 8-719-422-89 8-719-422-89 8-719-422-89 8-719-422-89 8-719-422-89 ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX D223 D224 D225 D306 8-719-422-89 8-719-422-89 8-719-422-89 8-719-988-61 ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX ZENER DIODE MA8082-H-TX DIODE 1SS355TE-17 <TERMINAL> ET001 ET002 ET007 SDM-N50 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 1-694-592-31 TERMINAL 1-694-592-31 TERMINAL 1-694-592-31 TERMINAL (a) REF.NO. PART NO. DESCRIPTION REMARK FB212 1-469-118-21 FERRITE 0UH FB213 FB214 FB216 FB217 FB218 1-469-324-21 1-469-647-21 1-469-118-21 1-469-118-21 1-469-118-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB219 FB220 FB221 FB301 FB302 1-469-118-21 1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB303 FB308 FB309 FB310 FB311 1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB316 FB318 FB319 FB320 FB321 1-469-324-21 1-469-118-21 1-469-118-21 1-469-324-21 1-414-445-11 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB324 FB325 FB326 FB327 FB328 1-469-647-21 1-469-647-21 1-469-647-21 1-469-647-21 1-469-647-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB329 FB330 FB331 FB332 FB333 1-469-647-21 1-469-647-21 1-469-647-21 1-469-647-21 1-469-647-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB334 FB335 FB336 FB337 FB338 1-469-647-21 1-469-647-21 1-469-647-21 1-469-647-21 1-469-647-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB339 FB340 FB341 FB342 FB343 1-469-647-21 1-469-647-21 1-469-113-21 1-469-113-21 1-469-113-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB344 FB345 FB346 FB347 FB348 1-469-113-21 1-469-113-21 1-469-113-21 1-469-113-21 1-469-113-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB349 FB350 FB351 FB352 FB353 1-469-113-21 1-469-113-21 1-469-113-21 1-469-113-21 1-469-113-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB354 FB355 FB356 FB357 FB358 1-469-113-21 1-469-113-21 1-469-113-21 1-469-113-21 1-469-113-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH <FERRITE BEAD> FB101 FB102 FB103 FB104 FB105 1-414-445-11 1-414-445-11 1-414-445-11 1-414-445-11 1-469-324-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB106 FB107 FB108 FB201 FB207 1-469-324-21 1-469-324-21 1-469-324-21 1-414-445-11 1-469-118-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 0UH FB208 FB209 FB210 FB211 1-469-118-21 1-469-118-21 1-469-118-21 1-469-118-21 FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 6-8 SDM-N50 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. (a) REF.NO. PART NO. FB359 FB360 FB361 FB362 1-469-113-21 1-469-113-21 1-469-113-21 1-469-113-21 DESCRIPTION FERRITE FERRITE FERRITE FERRITE REMARK 0UH 0UH 0UH 0UH <FILTER> FL301 FL302 FL303 1-234-498-21 FILTER, EMI 1-234-498-21 FILTER, EMI 1-469-461-21 FERRITE 0UH REF.NO. PART NO. The components identified by mark ¡ are critical for safety. Replace only with part number specified. DESCRIPTION REMARK <RESISTOR> R101 R102 R103 R104 R105 1-216-809-11 1-216-809-11 1-216-809-11 1-216-833-91 1-216-835-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100 100 100 10K 15K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R106 R107 R108 R109 R110 1-216-835-11 1-216-833-91 1-216-833-91 1-216-864-11 1-216-864-11 RES-CHIP RES-CHIP RES-CHIP SHORT SHORT 15K 10K 10K 0 0 5% 5% 5% 1/16W 1/16W 1/16W R111 R112 R113 R114 R115 1-216-835-11 1-216-835-11 1-216-864-11 1-216-864-11 1-216-819-11 RES-CHIP RES-CHIP SHORT SHORT RES-CHIP 15K 15K 0 0 680 5% 5% 1/16W 1/16W 5% 1/16W R116 R117 R118 R119 R120 1-216-813-11 1-216-809-11 1-216-833-91 1-216-821-11 1-216-809-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 220 100 10K 1K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R121 R122 R123 R124 R125 1-216-833-91 1-216-833-91 1-216-833-91 1-216-801-11 1-218-708-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP 10K 10K 10K 22 4.7K 5% 5% 5% 5% 0.50% 1/16W 1/16W 1/16W 1/16W 1/16W R126 R127 R128 R129 R130 1-216-864-11 1-216-864-11 1-216-809-11 1-216-809-11 1-216-809-11 SHORT SHORT RES-CHIP RES-CHIP RES-CHIP 0 0 100 100 100 5% 5% 5% 1/16W 1/16W 1/16W R131 R132 R133 R135 R136 1-216-809-11 1-216-809-11 1-216-809-11 1-216-833-91 1-216-833-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100 100 100 10K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R137 R138 R139 R141 R143 1-216-833-91 1-216-833-91 1-216-833-91 1-216-833-91 1-216-295-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP SHORT 10K 10K 10K 10K 0 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W R144 R145 R146 R147 R148 1-216-821-11 1-216-821-11 1-216-833-91 1-216-833-91 1-216-821-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1K 1K 10K 10K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R149 R150 R151 R152 R201 1-216-864-11 1-216-833-91 1-216-833-91 1-216-821-11 1-216-295-91 SHORT RES-CHIP RES-CHIP RES-CHIP SHORT 0 10K 10K 1K 0 5% 5% 5% 1/16W 1/16W 1/16W R202 R203 R205 R206 R207 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 SHORT SHORT SHORT SHORT SHORT 0 0 0 0 0 <IC> IC101 IC102 IC103 IC105 IC106 8-759-654-98 8-759-058-58 8-759-527-77 8-759-162-80 8-759-442-20 IC MB90F553APF-G-BND-AP01 IC TC7S04FU(TE85R) IC M24C16-MN6T IC MM1170BFB IC 24LC21AT/SN IC107 IC108 IC109 IC203 IC205 8-759-442-20 8-759-523-03 8-759-058-62 8-759-058-64 8-759-541-25 IC 24LC21AT/SN IC TC74HC4066AFT(EL) IC TC7S08FU(TE85R) IC TC7S32FU(TE85R) IC M52758FP IC206 IC207 IC208 IC209 IC210 8-759-584-88 8-759-524-04 8-759-599-01 8-759-491-46 8-759-523-96 IC BA7078AF-E2 IC TC74VHC125FT(EL) IC TC74VHCT14AFT(EL) IC TC74VHCT04FT(EL) IC TC74VHC86FT(EL) IC211 IC212 IC214 IC215 IC216 8-759-524-04 8-759-473-74 8-759-671-54 8-759-524-04 8-759-460-72 IC TC74VHC125FT(EL) IC SN74CBTD3306PWR IC AD9884AKS-100S IC TC74VHC125FT(EL) IC BA033FP-E2 IC301 IC302 IC303 IC304 8-759-650-75 8-759-641-60 8-759-641-60 8-752-087-78 IC CHEETAH3 IC MT48LC1M16A1TG-7S IC MT48LC1M16A1TG-7S IC CXB1455R <COIL> L201 1-419-424-21 INDUCTOR 47UH <IC LINK> PS201 ¡ 1-576-122-21 LINK, IC PS202 ¡ 1-576-122-21 LINK, IC <TRANSISTOR> Q101 Q102 Q103 Q201 Q301 8-729-900-53 8-729-900-53 8-729-046-75 8-729-230-49 8-729-046-75 TRANSISTOR DTC114EK TRANSISTOR DTC114EK TRANSISTOR SI2301DS-T1 TRANSISTOR 2SC2712-YG TRANSISTOR SI2301DS-T1 Q302 Q303 8-729-046-75 TRANSISTOR SI2301DS-T1 8-729-046-75 TRANSISTOR SI2301DS-T1 6-9 The components identified by mark ¡ are critical for safety. Replace only with part number specified. REF.NO. PART NO. SDM-N50 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK R208 R209 R210 R211 R212 1-218-706-11 1-216-022-00 1-216-022-00 1-216-022-00 1-216-805-11 METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 3.9K 75 75 75 47 0.50% 5% 5% 5% 5% 1/16W 1/10W 1/10W 1/10W 1/16W R213 R214 R215 R216 R217 1-216-295-91 1-216-295-91 1-216-805-11 1-216-295-91 1-216-805-11 SHORT SHORT RES-CHIP SHORT RES-CHIP 0 0 47 0 47 R218 R219 R220 R222 R224 1-216-295-91 1-216-295-91 1-216-295-91 1-216-805-11 1-216-805-11 SHORT SHORT SHORT RES-CHIP RES-CHIP 0 0 0 47 47 R225 R226 R227 R228 R229 1-216-864-11 1-216-022-00 1-216-022-00 1-216-022-00 1-216-805-11 SHORT RES-CHIP RES-CHIP RES-CHIP RES-CHIP 0 75 75 75 47 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/16W R231 R232 R233 R234 R235 1-216-805-11 1-216-801-11 1-216-801-11 1-216-801-11 1-216-805-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 47 22 22 22 47 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R236 R238 R239 R241 R242 1-216-805-11 1-216-825-11 1-216-825-11 1-216-833-91 1-216-821-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 47 2.2K 2.2K 10K 1K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R243 R244 R250 R252 R253 1-216-295-91 1-216-857-11 1-216-864-11 1-216-809-11 1-216-805-11 SHORT RES-CHIP SHORT RES-CHIP RES-CHIP 0 1M 0 100 47 R255 R256 R258 R259 R264 1-216-819-11 1-216-805-11 1-216-825-11 1-216-825-11 1-216-809-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP R267 R269 R274 R277 R278 1-216-801-11 1-216-809-11 1-216-833-91 1-216-295-91 1-216-295-91 R279 R280 R281 R282 R283 5% 1/16W 5% 1/16W 5% 5% 1/16W 1/16W (a) REF.NO. PART NO. DESCRIPTION REMARK R294 R295 R296 R298 1-216-864-11 1-216-864-11 1-216-808-11 1-216-801-11 SHORT SHORT RES-CHIP RES-CHIP 0 0 82 22 R299 R301 R302 R303 R307 1-216-833-91 1-216-864-11 1-216-833-91 1-216-864-11 1-216-833-91 RES-CHIP SHORT RES-CHIP SHORT RES-CHIP 10K 0 10K 0 10K R319 R320 R321 R322 R323 1-216-864-11 1-216-833-91 1-218-661-11 1-218-661-11 1-218-708-11 SHORT RES-CHIP METAL CHIP METAL CHIP METAL CHIP R325 R326 R327 R337 R338 1-218-708-11 1-218-692-11 1-218-692-11 1-216-801-11 1-216-833-91 R339 R340 R341 R342 R343 R344 R345 R347 R348 5% 5% 1/16W 1/16W 5% 1/16W 5% 1/16W 5% 1/16W 0 10K 51 51 4.7K 5% 0.50% 0.50% 0.50% 1/16W 1/16W 1/16W 1/16W METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP 4.7K 1K 1K 22 10K 0.50% 0.50% 0.50% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W 1-216-793-11 1-216-793-11 1-216-833-91 1-216-833-91 1-216-833-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 4.7 4.7 10K 10K 10K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W 1-216-833-91 1-216-833-91 1-216-813-11 1-216-805-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP 10K 10K 220 47 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W <NETWORK RESISTOR> 5% 1/16W 5% 5% 1/16W 1/16W 680 47 2.2K 2.2K 100 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W RES-CHIP RES-CHIP RES-CHIP SHORT SHORT 22 100 10K 0 0 5% 5% 5% 1/16W 1/16W 1/16W 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 1-216-835-11 SHORT SHORT SHORT SHORT RES-CHIP 0 0 0 0 15K 5% 1/16W R284 R285 R289 R290 R291 1-216-835-11 1-216-833-91 1-216-833-91 1-216-833-91 1-216-822-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 15K 10K 10K 10K 1.2K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W R292 1-216-833-91 RES-CHIP 10K 5% 1/16W RA101 RA102 RA203 RA204 RA205 1-239-412-11 1-239-412-11 1-239-412-11 1-239-412-11 1-239-412-11 NETWORK RESISTOR (CHIP) 100 NETWORK RESISTOR (CHIP) 100 NETWORK RESISTOR (CHIP) 100 NETWORK RESISTOR (CHIP) 100 NETWORK RESISTOR (CHIP) 100 RA206 RA207 RA208 1-239-412-11 NETWORK RESISTOR (CHIP) 100 1-239-412-11 NETWORK RESISTOR (CHIP) 100 1-239-412-11 NETWORK RESISTOR (CHIP) 100 <THERMISTOR> TH101 TH201 1-809-050-21 THERMISTOR 1-809-050-21 THERMISTOR <CRYSTAL> X101 X301 1-767-340-11 VIBRATOR, CRYSTAL 1-781-723-21 OSCILLATOR, CRYSTAL ******************************************************************************* 6-10 SDM-N50 (g) REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. CN701 CN702 CN703 CN704 CN705 1-694-592-31 TERMINAL 7-682-649-09 SCREW +PS 3X10 CN706 <CAPACITOR> ¡ 1-104-705-51 MYLAR DESCRIPTION 1-136-203-91 1-135-362-31 1-135-362-31 1-104-760-11 0.1UF MYLAR 0.01UF ELECT 1500UF ELECT 1500UF CERAMIC CHIP 0.047UF 20.00% 250V 20.00% 630V 20% 16V 20% 16V 10.00% 50V C707 C708 C709 C710 C711 1-107-824-11 1-163-037-11 1-163-021-91 1-104-760-11 1-126-968-11 CERAMIC 220PF CERAMIC CHIP 0.022UF CERAMIC CHIP 0.01UF CERAMIC CHIP 0.047UF ELECT 100UF 5.00% 10.00% 10.00% 10.00% 20.00% 1KV 50V 50V 50V 50V C712 C713 C716 C717 C719 1-163-007-11 1-126-967-11 1-128-949-31 1-164-156-11 1-125-991-11 CERAMIC CHIP 680PF ELECT 47UF ELECT 470UF CERAMIC CHIP 0.1UF ELECT 180UF 10.00% 20.00% 20% 50V 50V 16V 25V 450V C721 C722 C723 C724 C726 1-164-156-11 1-126-193-11 ¡ 1-117-699-41 ¡ 1-113-924-91 1-128-949-31 C727 C728 C729 C730 C732 ¡ 1-104-705-51 MYLAR 20% CERAMIC CHIP 0.1UF 25V ELECT CHIP 1UF 20.00% 50V CERAMIC 0.001UF 250V CERAMIC 0.0047UF 20.00% 250V ELECT 470UF 20% 16V * 1-691-591-11 * 1-766-376-11 * 1-691-960-11 * 1-691-960-21 1-573-290-21 PIN, CONNECTOR (1.5MM) (SMD)8P PIN, CONNECTOR (1.5MM)(SMD) 9P PIN, CONNECTOR (PC BOARD) 3P PIN, CONNECTOR (PC BOARD) 3P PIN, CONNECTOR (1.5MM) (SMD)4P 1-566-822-21 JACK <DIODE> D701 D702 D703 D704 D705 ¡ 8-719-077-76 DIODE D2SB60A-F04 8-719-510-41 8-719-018-82 8-719-911-19 8-719-063-73 DIODE D10SC9M DIODE RGP02-20EL-6394 DIODE 1SS119-25 DIODE D1NL20U-TR D706 D707 D708 D709 D710 8-719-200-82 8-719-106-53 8-719-976-96 8-719-046-85 8-719-046-85 DIODE 11ES2 ZENER DIODE RD10M-B2 ZENER DIODE DTE4.7C DIODE MA2S728 DIODE MA2S728 D711 D712 D767 D768 8-719-074-74 8-719-074-74 8-719-421-59 8-719-421-59 DIODE MA3XD15001S0 DIODE MA3XD15001S0 DIODE MA3130WA-TX DIODE MA3130WA-TX <TERMINAL> ET701 ET702 * 1-537-738-21 TERMINAL, EARTH * 1-537-738-21 TERMINAL, EARTH 1-164-156-11 0.1UF 20.00% 250V CERAMIC CHIP 0.1UF 25V CERAMIC 0.001UF 250V CERAMIC 0.0047UF 20.00% 250V CERAMIC CHIP 0.1UF 25V C735 C736 C737 C738 C739 1-164-156-11 1-126-603-11 1-128-949-31 1-128-949-31 1-164-156-11 CERAMIC CHIP 0.1UF ELECT CHIP 4.7UF ELECT 470UF ELECT 470UF CERAMIC CHIP 0.1UF 20.00% 20% 20% 25V 35V 16V 16V 25V C740 C741 C742 C743 C770 1-113-987-11 1-126-935-11 1-126-935-11 1-126-935-11 1-126-960-11 TANTAL. CHIP ELECT ELECT ELECT ELECT 4.7UF 470UF 470UF 470UF 1UF 20.00% 20.00% 20.00% 20.00% 20.00% 25V 6.3V 6.3V 16V 50V C771 C772 C790 C791 C792 1-126-960-11 1-126-933-11 1-126-960-11 1-126-960-11 1-126-960-11 ELECT ELECT ELECT ELECT ELECT 1UF 100UF 1UF 1UF 1UF 20.00% 20.00% 20.00% 20.00% 20.00% 50V 16V 50V 50V 50V IC701 IC702 IC704 IC706 IC707 8-759-594-75 8-759-198-31 8-759-652-21 8-759-651-71 8-759-652-21 C793 C794 C795 C796 C797 1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11 1-164-156-11 CERAMIC CHIP 100PF CERAMIC CHIP 100PF CERAMIC CHIP 100PF CERAMIC CHIP 100PF CERAMIC CHIP 0.1UF 5.00% 5.00% 5.00% 5.00% 50V 50V 50V 50V 25V IC790 8-759-510-71 IC BA10358F-E2 C798 1-126-933-11 ELECT 20.00% 16V 1-164-156-11 ¡ 1-117-699-41 ¡ 1-113-924-91 100UF REMARK <CONNECTOR> * A-1316-500-A G BOARD, COMPLETE **************************** C701 C703 C704 C705 C706 The components identified by mark ¡ are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. <FERRITE BEAD> FB750 FB751 1-469-136-21 FERRITE 1-469-136-21 FERRITE 0UH 0UH <FUSE> F701 ¡ 1-576-230-11 FUSE (H.B.C) (3.15A/250V) FH701 1-533-223-11 HOLDER, FUSE FH702 1-533-223-11 HOLDER, FUSE <IC> IC TEA1504/N2 IC uPC1093J-1-T IC MMDF6N03HDR2 IC MAX1631EAI-TG068 IC MMDF6N03HDR2 <COIL> L701 L702 L703 L704 6-11 1-412-534-31 1-412-532-11 1-408-611-31 1-406-663-21 INDUCTOR 56UH INDUCTOR 39UH INDUCTOR 47UH INDUCTOR 47UH The components identified by mark ¡ are critical for safety. Replace only with part number specified. REF.NO. PART NO. SDM-N50 Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. DESCRIPTION REMARK (g) REF.NO. PART NO. DESCRIPTION REMARK L705 1-406-663-21 INDUCTOR 47UH R771 1-216-699-11 RES-CHIP 100K 5% 1/10W L706 L707 1-406-663-21 INDUCTOR 47UH 1-406-661-11 INDUCTOR 22UH R772 R773 R774 R775 R776 1-216-699-11 1-216-699-11 1-216-651-11 1-216-651-11 1-218-478-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100K 100K 1K 1K 330 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/4W R777 R778 R779 R780 R781 1-218-478-11 1-216-659-11 1-216-659-11 1-218-476-11 1-216-295-91 RES-CHIP RES-CHIP RES-CHIP RES-CHIP SHORT 330 2.2K 2.2K 180 0 5% 5% 5% 5% 1/4W 1/10W 1/10W 1/4W R782 R783 R784 R785 R786 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 1-218-476-11 SHORT SHORT SHORT SHORT RES-CHIP 0 0 0 0 180 5% 1/4W R788 R789 R790 R791 R792 1-216-627-11 1-216-627-11 1-240-091-21 1-240-091-21 1-240-091-21 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 100 100 47K 47K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R793 R794 R795 R796 R797 1-240-091-21 1-240-091-21 1-240-091-21 1-240-091-21 1-240-091-21 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 47K 47K 47K 47K 47K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R798 R799 1-240-093-21 RES-CHIP 1-240-091-21 RES-CHIP 68K 47K 5% 5% 1/10W 1/10W <PHOTO COUPLER> PH701 8-749-010-64 PHOTO COUPLER PC123F2 <IC LINK> PS701 ¡ 1-533-595-31 LINK, IC PS702 ¡ 1-533-593-31 LINK, IC PS791 1-469-136-21 FERRITE 0UH <TRANSISTOR> Q701 Q770 Q771 8-729-926-79 TRANSISTOR IRFIBC40 8-729-230-49 TRANSISTOR 2SC2712-YG 8-729-230-49 TRANSISTOR 2SC2712-YG <RESISTOR> R701 R702 R703 R704 R705 ¡ 1-219-754-91 CARBON 1-215-929-11 1-216-073-00 1-219-776-11 1-216-665-11 680K METAL OXIDE 100K RES-CHIP 10K CARBON 2.2M METAL CHIP 3.9K 5% 1/2W 5% 3W 5% 1/10W 10% 1/2W 0.50% 1/10W R706 R707 R708 R709 R710 1-216-651-11 1-216-073-00 1-216-073-00 1-216-093-91 1-216-295-91 METAL CHIP RES-CHIP RES-CHIP RES-CHIP SHORT 1K 10K 10K 68K 0 0.50% 5% 5% 5% R711 R712 R713 R714 R716 1-215-887-00 1-215-887-00 1-219-776-11 1-216-049-91 1-216-635-11 METAL OXIDE METAL OXIDE CARBON RES-CHIP METAL CHIP 150 150 2.2M 1K 220 5% 2W 5% 2W 10% 1/2W 5% 1/10W 0.50% 1/10W R717 R718 R719 R721 R722 1-217-151-00 1-216-109-00 1-260-306-51 1-216-001-00 1-216-049-91 METAL RES-CHIP CARBON RES-CHIP RES-CHIP 0.22 330K 15 10 1K 10% 5% 5% 5% 5% 2W 1/10W 1/2W 1/10W 1/10W R723 R724 R725 R726 R727 1-216-658-11 1-216-049-91 1-208-816-11 1-216-101-00 1-216-033-00 METAL CHIP RES-CHIP METAL CHIP RES-CHIP RES-CHIP 2K 1K 27K 150K 220 0.50% 5% 0.50% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R728 R730 R731 R732 R733 R735 R736 R737 R770 ¡ 1-220-778-21 FUSIBLE 1/10W 1/10W 1/10W 1/10W 1-243-290-91 1-240-581-11 1-216-797-11 1-243-290-91 METAL CHIP CEMENTED RES-CHIP METAL CHIP 0.1 0.068 3.9 10 0.068 10% 1% 5% 5% 1% 1/2W 1/2W 10W 1/16W 1/2W 1-216-041-00 1-218-727-11 1-218-726-11 1-216-699-11 RES-CHIP METAL CHIP METAL CHIP RES-CHIP 470 30K 27K 100K 5% 0.50% 0.50% 5% 1/10W 1/16W 1/16W 1/10W <TRANSFORMER> T701 T702 ¡ 1-419-621-11 INDUCTOR 7.4MH 1-435-291-21 TRANSFORMER, CONVERTER (SRT) <VARISTOR> VDR701¡ 1-801-073-11 VARISTOR ERZV14D471 6-12 SDM-N50 DESCRIPTION REMARK REF.NO. PART NO. The components identified by mark ¡ are critical for safety. Replace only with part number specified. DESCRIPTION REMARK SDM-N50 REF.NO. PART NO. Les composants identifiés par une marque ¡ sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 9-978-671-01 2000BL24XXX-1 Sony Corporation 9-978-671-01 Computer Display Division Company Computer Display Div. – 86 – English 2000BL24XXX-1 Printed in Japan © 2000.2
