Download Scag Power Equipment 70001, 79999 Operator`s manual

OPERATOR’S MANUAL
MODEL SWZ
THIS MANUAL CONTAINS THE OPERATING
INSTRUCTIONS AND SAFETY INFORMATION
FOR YOUR SCAG MOWER. READING THIS
MANUAL CAN PROVIDE YOU WITH ASSISTANCE IN MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR MOWER
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MACHINE, PLEASE READ ALL THE INFORMATION ENCLOSED.
PART NUMBER 03031
WARNING:
FAILURE TO FOLLOW SAFE OPERATING PRACTICES
MAY RESULT IN SERIOUS INJURY.
* Keep all shields in place, especially the grass discharge chute.
* Before performing any maintenance or service, stop the machine and
remove the spark plug wire and ignition key.
* If a mechanism becomes clogged, stop the engine before cleaning.
* Keep hands, feet and clothing away from power-driven parts.
* Read this manual completely as well as other manuals that came
with your mower.
REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!
Hazard control and accident prevention are dependent upon the awareness,
concern, prudence, and proper training of the personnel involved in the
operation, transport, maintenance, and storage of the equipment.
This manual covers the operating instructions
and illustrated parts list for:
All SWZ machines
with a serial number of xxx70001 - xxx79999
Always use the entire serial number listed on the serial number
tag when referring to this product.
SIGNAL WORDS
INTRODUCTION
Your mower was built to the highest standards in the
industry. However, the prolonged life and maximum
efficiency of your mower depends on you following
the operating, maintenance and adjustment instructions in this manual.
This symbol means “Attention! Become Alert!
Your Safety is Involved!" The symbol is used with
the following signal words to attract your attention
to safety messages found on the decals and throughout this manual. The message that follows the
symbol contains important information about safety.
To avoid injury and possible death, carefully read the
message! Be sure to fully understand the causes of
possible injury or death.
We encourage you to contact your dealer for repairs.
All Scag dealers are informed of the latest methods
to service this equipment and provide prompt and
efficient service in the field or at their service shop.
They carry a full line of Scag service parts.
A replacement Operator's Manual is available from
your Scag Servicing Dealer or by contacting Scag
Power Equipment, Service Department, at P.O. Box
152, Mayville, WI 53050. Please indicate the complete model and serial number of your Scag product.
Signal Word:
It is a distinctive word on safety decals and throughout this manual that alerts the viewer to the existence
and relative degree of the hazard.
USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.
The “Right” and “Left”, “Front” and “Rear” of the
machine are referenced from the operator’s perspective when in the normal operating position and facing
the forward travel direction.
The signal word “DANGER” denotes that an extremely hazardous situation exists on or near the
machine that could result in high probability of death
or irreparable injury if proper precautions are not
taken.
GENERAL SAFETY INSTRUCTIONS
READ THIS OPERATOR'S MANUAL and
instructions furnished with attachments.
WARNING:
Perform only those maintenance procedures described in this manual. If major repairs are ever
needed or assistance is desired, contact an Authorized Scag Dealer. To ensure optimum performance
and safety, always purchase genuine SCAG replacement parts and accessories.
The signal word “WARNING” denotes that a hazard
exists on or near the machine that can result in injury
or death if proper precautions are not taken.
Your safety and the safety of others depends significantly upon your knowledge and understanding of all
correct operating practices and procedures of this
machine.
The signal word “CAUTION” is a reminder of safety
practices on or near the machine that could result in
personal injury if proper precautions are not taken.
CAUTION:
1
BEFORE OPERATING
WHILE OPERATING
1. Know the controls and how to stop quickly.
1. Start the engine when the neutral latches are in
the neutral lock position, the cutter blades are
disengaged, the parking brake is on and the speed
adjustment lever is in the neutral position.
2. Do not allow children to operate the machine.
Do not allow adults to operate the machine
without proper instruction.
2. Do not run the engine in a confined area without
adequate ventilation. Exhaust fumes are hazardous and could possibly be deadly.
3. Remove all debris or other objects that might be
picked up and thrown by the cutter blades. Keep
all bystanders away from the mowing area.
3. Using the machine demands attention. To
prevent loss of control:
A. Mow only in daylight or when there is good
artificial light.
B. Watch for holes or other hidden hazards.
C. Do not drive close to a drop-off, ditch, creek
bank, or other hazard.
D. Reduce speed when making sharp turns and
when turning on hillsides.
E. Always be sure of your footing. Keep a firm
hold on the handles and walk---never run.
F. Do not operate where conditions are slippery.
4. Keep all shields, safety devices, and decals in
place. If a shield, safety device or decal is defective or damaged, repair or replace it before
operating. Also, check all nuts, bolts and screws
for proper tightness, to assure the machine is in
safe operating condition.
5. Do not operate the machine while wearing
sandals, tennis shoes, sneakers or shorts. Also,
do not wear loose fitting clothing which could get
caught in moving parts. Always wear long pants
and substantial shoes. Wearing safety glasses and
safety shoes is advisable and required by some
local ordinances and insurance regulations.
4. The discharge chute must always be installed and
in the down position on the side discharge cutter
deck except when the Scag optional grass
catcher or mulching plate are properly installed.
If the discharge area should plug, shut the engine
off and wait for all movement to stop before
removing the obstruction.
6. Fill the fuel tank with clean, fresh gasoline, with a
minimum octane rating of 87. Avoid spilling
gasoline. Gasoline is highly flammable, handle it
carefully.
A. Use an approved gasoline container.
B. Do not fill the tank while the engine is hot or
running.
C. Do not smoke while handling gasoline.
D. Fill the fuel tank outdoors and up to approximately 1" (25 mm) below the bottom of the
filler neck.
E. Wipe up any spilled gasoline.
5. Disengage the blades and wait for them to stop
before crossing gravel drives, walks or roads.
6. Shut the engine off and wait until the blades
come to a complete stop before removing the
grass catcher container.
7. Never raise the cutter deck while the blades are
rotating.
7. Before attempting to start the engine, move the
speed adjustment lever into the neutral position,
move the blade engagement switch to the OFF
position, apply the parking brake, and move the
neutral latches to neutral.
8. Always park the mower and/or start the engine
on a level surface. Apply the parking brake to
prevent the mower from moving when you are
not in the operator’s position.
2
14. Use only Scag approved riding attachments.
9. If the cutting blades should strike a solid object
or the equipment should start to vibrate abnormally, stop the engine, disconnect the spark plug
wire, and check immediately for the cause.
Vibration is generally a warning of trouble.
Check the machine for damaged or defective
parts. Repair any damage before starting the
engine or operating the cutter deck. Be sure the
blades are in good condition and the blade bolts
are tight.
Scag Approved Riding Attachments:
RS-ZT
Using unapproved attachments, (especially "standup" riding attachments) may be hazardous.
MAINTENANCE AND STORAGE
1. Disconnect the spark plug wire from the spark
plug to prevent accidental starting of the engine
when servicing, adjusting or storing the machine.
10. Reduce speed and exercise extreme caution on
slopes and in sharp turns to prevent tipping or
loss of control. Be especially cautious when
changing directions on slopes.
2. If the mower must be tipped to perform maintenance or adjustment, remove the battery, drain
the gasoline from the fuel tank and the oil from
the crankcase.
WARNING:
DO NOT operate on steep slopes. To check a
slope, attempt to back up it (with the cutter deck
down). If the machine can back up the slope
without the wheels slipping, reduce speed and
use extreme caution. ALWAYS FOLLOW OSHA
APPROVED OPERATION.
3. To reduce potential fire hazard, keep the engine
free of excessive grease, grass, leaves and accumulations of dirt.
4. Be sure the machine is in safe operating condition
by keeping nuts, bolts, and screws tight. Check
the blade mounting bolts and nuts frequently to
be sure they are tightened.
11. Do not touch the engine or muffler while the
engine is running or soon after it is stopped.
These areas could be hot enough to cause a burn.
5. If the engine must be running to perform a
maintenance adjustment, keep hands, feet, clothing and other parts of the body away from the
cutter deck blades and other moving parts.
12. Before leaving the operator’s position or leaving
the mower unattended, move the speed adjustment lever into the neutral position, place the
neutral latches in the neutral lock position, apply
the parking brake, and move the blade engagement switch to OFF. Shut the engine OFF and
remove the key.
6. Do not overspeed the engine by changing governor settings. To be sure of safety and accuracy,
have an authorized dealer check maximum engine
speed with a tachometer.
7. The engine must be shut off before checking the
oil or adding oil to the crankcase.
13. Do not pass or stand on the grass discharge side
of any mower with the engine running. Stop
operation when another person approaches.
8. Allow the engine to cool before storing the
mower in any enclosure such as a garage or
storage shed. Make sure the fuel tank is empty if
the machine is to be stored in excess of 30 days.
Do not store the mower near any open flame or
where gasoline fumes may be ignited by a spark.
WARNING
FALLING HAZARD
USE ONLY SCAG APPROVED
RIDING ATTACHMENTS
SEE OPERATOR'S MANUAL
481109
3
9. Always store gasoline in a safety-approved, red
container.
MOWER OPERATION
1. Read and understand the safety instructions
before attempting to operate this machine.
10. Be careful when servicing the battery as it contains acid, which is corrosive and could cause
burns to skin and clothing.
2. Before starting the engine:
* Check the oil level in the engine and the
hydraulic reservoir.
* Fill the fuel tank with clean, fresh, lead-free
gasoline.
* Open the fuel valve on the bottom of the
fuel tank.
11. Batteries release explosive gases when being
charged or discharged. Keep batteries away
from any source of sparks and/or flame.
12. Make sure all hydraulic connections are tight and
all hydraulic hoses and lines are in good condition before starting the machine.
-NOTEUse gasoline with an octane rating no less than
87.
13. Hydraulic fluid is under high pressure. If you
need service on your hydraulic system, please see
your authorized Scag dealer.
* The speed adjustment lever must be in
NEUTRAL.
* The blade clutch switch must be in the OFF
position.
* The neutral latches must be in the neutral
lock position.
* The key switch must be on.
* The parking brake must be on.
INITIAL RUN-IN PROCEDURES
(FIRST DAY OF USE OR APPROXIMATELY 10 HOURS)
1. Check the belts for proper tension at 2, 4 and 8
hours. Adjust as needed.
3. Start the engine:
2. Check the steering control rods and the speed
control for neutral adjustment. (See Adjust
ments, page 6-8)
* Choke as required. If the engine is cold, pull
the choke knob out. When the engine starts,
slowly push the choke in. If the engine stalls,
repeat the above operation. When the engine
is warm, choking may not be necessary.
3. Check the tires for proper pressure.
Caster Wheels
25 psi.
Drive Wheels
15 psi.
4. Engage the cutter blades by lifting and pushing
the blade cluch switch into the ON position. Pull
the switch to the OFF position to disengage the
cutter blades.
4. Check for loose hardware. Tighten as needed.
5. Check the safety switches for proper adjustment:
* The engine should crank and start if the
machine is in neutral, the PTO engagement switch is OFF and the parking brake
is ON.
-NOTEWhen PTO is engaged or (possibly) disengaged,
a squealing sound from the underside of the
machine is normal. It is caused by the electric
clutch plates meshing as the mower comes up to
speed. For best equipment life, engage the
clutch with the engine at 1/2 throttle, not under
full load.
6. Apply lubricant to all the grease fittings. Lubricant was applied at the factory. This is just a
precautionary check to make sure that all the
fittings have been lubricated.
4
CUTTER DECK BELT ADJUSTMENTS
WARNING:
If you are not familiar with the operation of the
hydrostatic drive and zero turn feature, practice
turning and maneuvering with the hand controls
before engaging the blades.
-NOTEThe hydro drive belt is spring loaded and does
not require adjustment.
1. Remove the belt cover.
5. Release the parking brake. Move the speed
adjustment lever to the desired mowing speed.
2. Adjust the cutter deck drive belt using a belt
tension gauge. Adjust the belt so that the belt
moves 1/2" with 10 pounds of pressure. Adjust
the tension by tightening or loosening the J-bolt
nut. (See figure 2)
-NOTETop speed is suggested only for transport!
6. While squeezing the steering brake levers with
both hands, release both neutral latches.
END OF L-SHAPED
BRACKET
BELT
7. When the steering brake levers are released, the
machine will travel straight. To make a right
turn, squeeze the RH lever. To turn left,
squeeze the LH lever.
NUT
"J" BOLT
WASHER
8. TO STOP, squeeze both levers, lock the neutral
latches, and move the speed adjustment lever to
neutral.
9. To move the machine in reverse, squeeze up on
both steering control levers.
CUTTER DECK DRIVE BELT TENSION
ALIGNMENT IDLER - L.H.
Figure 2 Deck Drive Belt Adjustment
10. To "freewheel" or move the machine around
without the engine running, turn the dump valve
levers located at the back of the pumps to the
"freewheel" positions.(see Figure 1). To operate
the machine the dump valve levers must be
returned to the closed positions.
-NOTEDue to initial belt stretch and to prevent the belt
from slipping, check this adjustment after the
first 2 hours, 4 hours and 8 hours of operation.
3. Adjust the RH blade drive belt using a belt
tension gauge.
Adjust theforbelt so that the belt
ire pressure
can be adjusted
moves 1/2" with 10 pounds of pressure. Adjust
the tension by tightening or loosening the J-bolt
nut. (See figure 3)
Dump Valve Levers
(normal position)
Figure 1 Dump Valves
SC400G
SGB112
5
Nut
Washer
LOW CUT (1 3/4"- 3")
Deck
MID RANGE
(2 1/2"- 3 3/4")
"J" Bolt
HIGH CUT (3 1/4"- 4 1/2")
Belt
Figure 3. Cutter Deck Belt Adjustment R.H.
CUTTER DECK HEIGHT ADJUSTMENT
4. Replace the belt cover.
SC405G
Figure 4 Cutting Height Adjustment
Caster spacers also can be repositioned to change
cutting heights and to change the pitch of the deck.
(See figure 5)
CUTTER DECK ADJUSTMENTS
Due to the many cutting conditions that exist, it is
difficult to suggest a cutter deck setting that will
work for every lawn. There are two adjustments
that can be made on these decks, pitch and height.
PIN
SPACERS
PITCH is the angle of the blades (comparing front
to rear). A 1/4" downward pitch (front of deck
down) is recommended for best cutting performance.
HEIGHT is the nominal distance the blade is off of
the ground. This measurement is made with the
blades pointed side to side and distance is measured
between cutting tip and ground. (Also see Blade
Height Adjustment)
Changes to the cutting height can be achieved by
repositioning the cutter deck. (This adjustment will
also effect the pitch of the deck). There are three
available positions (see figure 4).
REPOSITIONING SPACERS
SC406G
Figure 5. Caster Wheel Spacers
BLADE HEIGHT ADJUSTMENT
Adjusting the blade height can be done by moving
any number of the five smaller 1/4" spacers on the
blade mounting bolts to the top of the spindle shaft or
below the spindle shaft.
-NOTEAll blades should be positioned equally.
For best cut and discharge, a minimum of three
spacers should be installed between the blade and the
spindle. (See figure 6)
6
ANGLE BLADE BACK
X
DO NOT CUT IN
X MUST NOT EXCEED
1/3 BLADE WIDTH
30
SC4O8G
Figure 7. Blade Sharpening
NEUTRAL ADJUSTMENT
1. Raise the drive wheels off the ground and block
the caster wheels.
2. Remove the speed control spring and the steering control rod from the machine. (See figure 8)
Steering Control
Rod
Bolts
SC407G
Spring
Figure 6. Blade Spacers
Bellcrank
Handle
SC160G
Figure 8 Neutral Adjustment
3. Loosen the wing nut and let the speed adjustment bearing lever fall away from the cam.
CUTTER BLADES
4. Start the engine and observe the drive wheels. If
the drive wheels are rotating, Loosen the bolts
on the neutral adjustment handle and move the
handle up or down until the wheels are in neutral. (See figure 8)
Do not sharpen beyond 1/3 of the width of the blade.
(See figure 7)
-NOTEDress the blade with a file. Using a wheel
grinder may burn the blade. Check the balance
of the blade. If blades are out of balance, vibration and premature wear of spindle assembly can
occur. See your authorized Scag dealer for
blade balancing or special tools, if you choose to
balance your own blades.
5. Tighten the bolts on the neutral adjustment
handle. When tightening the bolts, hold the
bellcrank to prevent it from moving and throwing off the neutral adjustment.
6. Turn the engine off.
7
3. Tighten the bearing securing the speed adjustment bearing lever and repeat on the opposite
side.
STEERING CONTROL ROD
ADJUSTMENT
-NOTEThis adjustment is made to allow the steering
control levers to be moved out of the neutral
latch without engaging reverse.
4. With the machine on a flat level surface, start the
engine and place the speed adjustment lever into
the speed that will most often be used.
5. Squeeze the steering control levers and release
the neutral latch. Slowly release the steering
control levers allowing the machine to move
forward.
1. Connect the steering control rods into the steering control levers on the handle. Do not install
the hair pin at this time.
2. Turn the swivel joint on the steering control rods
until the swivel joint is centered in the slot in the
bellcrank.
6. If the machine pulls to one side, put the speed
adjustment lever back into the neutral position
and turn the engine off.
3. Remove the steering control rods from the
machine. Install the speed control spring onto
the swivel joint. Reinstall the steering control
rods onto the machine and secure using the hair
pins.
7. On the side that the machine pulled toward,
loosen the wing nut securing the speed adjustment bearing lever and move the bearing 1/16"
away from the cam. Start the engine and recheck
the tracking. Adjust as needed.
TRACKING ADJUSTMENT
8. If tracking cannot be achieved, contact your Scag
servicing dealer.
-NOTEBefore proceeding with this adjustment be sure
that the tire pressures are correct. (see page 4)
and that the neutral adjustment and the steering
control rod adjustment have been completed.
PARKING BRAKE
1. Adjust the parking brake so that when the brake
hand lever is against the stop on the handle bar,
the brake levers on the brake shaft weldment are
against the stops on the engine deck.
1. Engage the neutral latch on both steering control
levers and move the speed adjustment lever into
the neutral position.
CAUTION:
2. Position the speed adjustment lever so that the
bearing just contacts the speed adjustment cam.
(See figure 9)
Steering Control Rod
Swivel
Joint
Adjust the brake only enough to hold the
machine. Excessive force may cause damage
to the machine or brake components.
Speed Adjustment
Cam
2. Adjust the brake actuator rod on either side of
the machine to obtain proper brake adjustment.
Bearing
Speed
Adjustment
Bearing Lever
Speed Control Spring
Bellcrank
SC161G
8
LUBRICATION & MAINTENANCE
BREAK-IN
+ Grease spindle until grease comes out the relief valve
Compatible Greases:
Lidok EP #2 (found at industrial shops)
Ronex MP (Exxon service stations)
40 HOURS (WEEKLY)
Shell Alvania (Shell service stations)
Mobilux #2 (Mobil service stations)
100 HOURS (BIWEEKLY)
Super Lub M EP #2 (Conoco service stations)
8 HOURS (DAILY)
500 HRS OR ANNUALLY
COMMENTS
PROCEDURE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Check all hardware for proper tightness
Change engine oil and filter at 5 hours
Check engine oil
Remove debris from under belt cover
Sharpen cutter blades
Grease spindle bearings
Clean air filter
Check belt tension
Check tire pressure
Check battery level
Replace air filter
Grease caster wheel bearings
Grease caster wheel pivot shafts
Grease idler pulley bracket on cutter deck
Change hydrostatic oil filter
Change engine oil and filter
Grease idler arm pivots
Grease brake hand lever
Grease brake actuator levers
Check all hardware for proper tightness
Adjust air gap on electric clutch
Drain hydraulic system and replace oil
Do not over fill
More often if needed
More often if needed
+ US Lithium MP White Grease 2125
More often if needed
Add or adjust as required
Adjust as needed
More often if needed
Chassis grease
Chassis grease
Chassis grease
Clean area before removing the filter
See engine manufacturer information
Chassis grease
Chassis grease
Chassis grease
Contact your Scag dealer for information about
making this adjustment
9
TROUBLESHOOTING CUTTING CONDITIONS
CAUSE
CONDITION
Stringers - Occasional
Blades of Uncut
Grass
CURE
Low engine RPM
Run engine at full 3600 RPM
Ground speed too fast
Slow speed to adjust for conditions
Wet grass
Cut grass after it has dried out
Dull blades, incorrect sharpening
Sharpen blades
Deck plugged, grass accumulation Clean underside of deck
Width of Deck
Belts slipping
Adjust belt tensions
Dull, worn blades
Sharpen blades
Incorrect blade sharpening
Sharpen blades
Low engine RPM
Run engine at full 3600 RPM
Belt slipping
Adjust belt tension
SGB020
Streaking - Strips of
Uncut Grass in Cutting
Path
Deck plugged, grass accumulation Clean underside of deck
Width of Deck
Ground speed too fast
Slow speed to adjust for conditions
Wet grass
Cut grass after it has dried out
Bent blades
Replace blades
Not enough overlapping
between rows
Increase the overlap of each
pass
SGB018
Streaking - Strips of
Uncut Grass Between
Cutting Paths
Width
of
Deck
SGB019
Width
of
Deck
10
TROUBLESHOOTING
CAUSE
CONDITION
Uneven Cut on Flat
Ground - Wavy
High-Low
Appearance,
Scalloped Cut, or
Rough Contour
CURE
Lift worn off of blade
Replace blade
Blade upside down
Mount with cutting edge toward
ground
Deck plugged,grass accumulation
Clean underside of deck
Too much blade angle (deck pitch) Adjust pitch and level
Deck mounted improperly
See your authorized SCAG dealer
Bent spindle area
See your authorized SCAG dealer
Dull blade
Sharpen blade
Uneven ground
May need to reduce ground speed,
raise cutting height, and/or change
direction of cut
Tire pressures not equal
Check and adjust tire pressure
Wheels uneven
Check and adjust tire pressure
Deck mounted incorrectly
See your authorized SCAG dealer
Width of Deck
SGB020
Uneven Cut on
Uneven Ground Wavy Appearance,
High-Low Scalloped
Cut, or Rough Contour
Width of Deck
SGB021
Sloping Ridge Across
Width of Cutting Path
Width of Deck
SGB023
11
TROUBLESHOOTING
CAUSE
CONDITION
Scalping - Blades
Hitting Dirt or
Cutting Very Close to
the Ground
Width of Deck
CURE
Low tire pressures
Check and adjust pressures
Ground speed too fast
Slow speed to adjust for conditions
Cutting too low
May need to reduce ground speed,
raise cutting height, change direction
of cut, and/or change pitch and level
Rough terrain
May need to reduce ground speed,
raise cutting height, and/or change
direction of cut
Ground speed too fast
Slow speed to adjust for conditions
Wet grass
Cut grass after it has dried out
Blades not mounted evenly
Adjust pitch and level
Bent blade
Replace blade
Internal spindle failure
See your authorized SCAG dealer
Mounting of spindle incorrect
See your authorized SCAG dealer
Bent spindle mounting area
See your authorized SCAG dealer
Internal spindle failure
See your authorized SCAG dealer
Bent deck housing
See your authorized SCAG dealer
SGB022
Step Cut
Ridge in Center of
Cutting Path
Width of Deck
SGB024
Slope Cut - Sloping
Ridges Across Width
of Cutting Path
Width of Deck
SGB025
12
TECHNICAL SPECIFICATIONS
ENGINES
General Type:
Brand:
Models:
Horsepower:
Type:
Displacement:
Cylinders:
Governor:
Exhaust Group:
Fuel Pump Group:
Oil Pump Group:
Valve Group:
Starter/Electrical:
Charging System:
Heavy duty industrial/commercial
Kohler, Kawasaki, Briggs & Stratton
Kohler CV14T, CVE 20;Kaw. FC420V;B&S 303776, 350777
Kohler 14HP& 20HP; Kaw. 14HP; B&S 16HP & 18HP; Kaw. 17HP
4 cycle gas, vertical shaft engines
Kohler: 14HP = 398cc, 20 HP= 624 cc
Kawasaki: 14HP = 423cc, 17HP = 494cc
B & S 16HP = 480 cc, 18HP = 570cc
Varied - see manufacturer's specifications
Mechanical type governor with variable speed control set
at 3600 rpm (+75 rpm), idle set at 1200 rpm (+75 rpm)
Single exhaust canister muffler
Varied - See manufacturer's specifications
Varied - See manufacturer's specifications
Varied - See manufacturer's specifications
Electronic Ignition with recoil starter or 12 volt battery with
alternator, solid state ignition with key start
15 amp
ENGINE DECK
Thickness:
Fuel Tank:
Drive Wheels/Tires:
Brakes:
Axles:
Handle Bars:
7 gauge steel
5 gallon (19.0 litres) seamless polyethylene
16x6.50-8 four-ply pneumatic tubeless, radius edge
Dynamic braking through hydro drive system
1" tapered
1-1/4" diameter
DRIVE SYSTEM
Type:
Hydro Pumps:
Drive Wheel Motors:
Hydro Fluid Cooling Group:
Steering / Travel Control::
Parking Brakes:
Dump Valves:
Axles:
Wire Harness:
Safety Group:
Forward Speed Range:
Reverse Speed Range:
Hydro drive with two variable displacement pumps and two
cast-iron high torque motors
Two Hydro-Gear Model BDP 10L pumps with dump valves for
movement without running the engine
Two 12 cu. inch cast-iron high torque motors
Heavy-duty cooling radiator, 7 qt. capacity cooling
reservoir, uses, SAE 10W30 fluid and 10 micron filter
Independent handle controls for each wheel, squeeze to move
from forward to neutral to reverse, neutral lock lever, speed
range controlled with single lever (patented design), in-field
tracking adjustment with no tools necessary
7.5" drum, band brake, one on each wheel
Allows for movement without engine running
1" tapered motor shafts
14 gauge wire
Handle actuated operator presence system (patented design),
blade / clutch and transmission interlock to engine kill
0 to 7.4 mph
0 to 3.0 mph
Date of Issue: December 8, 1997
Specifications Subject to Change Without Notice
13
TECHNICAL SPECIFICATIONS (CON'T)
CUTTER DECKS
Type:
Construction:
Cutting Width:
Cutting Height Adjustment:
Cutter Blades:
Blade Engagement:
Discharge Opening:
Caster Wheels:
Spindles:
Spindle Pulleys:
Idler Pulley:
Idler Arm:
Cutter Deck Belts:
SWM 36, SWM 48, SWM 52, SWM 61, SWM 72
Out-front design with anti-scalp rollers
SWM36,48: 7-gauge steel with 7-gauge (3/16") steel skirt
SWM52,61,72:10-gauge steel with 7-gauge (3/16") steel
skirt
35.5" (90.2 cm), 48.0 (122.0 cm), 52.0 " (132.0 cm),
61.0 " (155.0 cm), 71.5" (181.6 cm)
Adjustable from 1-3/4" to 4-1/4" in 1/4" increments
.204 thick, milled edge, 5150 alloy steel
SWM 36: Two (2) 18" SWM 48: Three (3) 16.5"
SWM 52: Three (3) 18" SWM 61: Three (3) 21"
SM72: Three (3) 24" blades
Electric blade brake clutch with instrument panel switch
Extra wide 11.5", 13.75 " discharge opening with hinged
chute
9.4 x 3.5 smooth tread flotation, inner tubes, split rims, roller
bearings, with quick pin removal
Cast housing, taper roller bearing, low maintenance with
top access grease fitting and grease overfill relief poppet
Cast-iron with easily removed taper hubs
5" diameter pulley, welded and riveted construction,
1-3/8" O.D. Bearing
Heavy duty idler arm of 1/4" channel steel
B-section with Kevlar cord
ADDITIONAL SPECIFICATIONS
OPTIONAL ITEMS/ATTACHMENTS
Fabric Grass Catcher:
Metal Grass Catcher:
Steerable Sulky:
Mulching Plate:
GC-F4 Grass Catcher with 4 cubic ft. capacity
GC-4D Grass Catcher with 4 cubic ft. capacity and rope pull
dump or pick-up and dump
RS-ZT Steerable Sulky with padded seat and full articulation
for zero-radius turning
Steel plate fits over discharge opening. No blade change or
or removal required. Installs and removes in the field.
APPROXIMATE DIMENSIONS
SWM36 SWM48 SWM52 SWM61 SWM72
Length:
Length with Grass Catcher:
Tracking Width:
Width:
Width (with discharge chute up):
With with grass catcher:
Height:
Height with grass catcher:
Weight
Weight with grass catcher:
Turning Radius:
74.0"
74.0"
37.0"
54.5"
37.5"
55.0"
40.5"
40.5"
510 lbs.
550 lbs.
Zero
Date of Issue: December 8, 1997
Specifications Subject To Change Without Notice
14
74.0"
74.0"
42.0"
60.0"
53.0"
69.0"
40.5"
40.5"
550 lbs.
590 lbs.
Zero
74.0"
74.0"
42.0"
60.0"
53.0"
69.0"
40.5"
40.5"
590 lbs.
630 lbs.
Zero
76.0"
76.0"
42.0"
70.0"
63.0"
80.0"
40.5"
40.5"
625 lbs.
665lbs.
Zero
76.0"
76.0"
42.0"
81.0"
74.0"
91.0"
40.5"
40.5"
695lbs.
730 lbs.
Zero
32" & 36" CUTTER DECKS
41
9
45
47
43
11
41
44
44
45
61
59
11
46
46A
43
58
57
22
42
53
A
41
39
39A
40
48
7
60
58
42
54
14
55
50
13
56
37
18
49
52
38
36
51
A
49
2
19
37
20
21
14
55
35
40
22
21
8
20
1
1A
14
25
23
24
62
27
28
26
35
10
5
66
29
22
6
34
32
31
33
4
11
3
12
30
31
11
64
5
15
15A
16
63
67
17
SC409G
18
65
36" CUTTER DECK
Ref. Part
No. No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
15A
16
17
18
19
20
21
22
23
24
25
26
27
28
29
NS
30
31
32
33
34
35
36
37
38
39
Cutter Deck (Includes decals)
CutterSpindle Assembly
Spacer, Inside
Tapered Nut, 5/16-24
Tapered Bearing (two)
Spindle Housing, Tapered Bearing
Grease Fitting Str. 5/16
Spindle Shaft
Hex Head Bolt, 3/8-16 x 3-1/2"
Key, 1/4 x 2"
Spacer, Cutter Blade
Hex Head Bolt, 5/16-18 x 1-1/4"
Spacer
Nut, 5/16-18 Serrated Flange
Cutter Blade, 18"
Cutter Blade, 18" High Lift
Flat Washer, 5/8" W
Hex Hd. Bolt, 5/8-11 x 9-1/2"
Caster Assembly (includes 19-28)
Quick Pin
Spacer, Caster Yoke, 1/2" thick
Bronze Bearing
Spring, Chute Return
Support Assy. (incl. 21-23)
Caster Yoke
Sleeve, Caster Wheel Bearing
Hex Hd. Bolt, 1/2-13 x 5-1/2"
Hex Locknut, 1/2-13
Wheel Assy. (incl. 4,29-34)
Tire only, Caster Wheel
Inner Tube Only (not shown)
Rim Pair, Caster Wheel
Retainer, Bearing, Caster Wheel
Roller Bearing, Caster Wheel
Grease Fitting 45 deg., 1/4-28
Hub Assy. (incl. bolts)
Capscrew, 5/16-18 x 3/4" Serr. Flange Hex Head
Discharge Chute
Hex Nut, 5/16-18 Elastic Stop
Hex Head Bolt, 5/16-18 x 1"
Belt Cover Assembly
46850
46631
43296
48307-08
481022
43294
48114-04
43298
04001-77
04063-08
43278
04001-10
43077
04019-03
48108
48185
04040-10
04001-41
46079
04066-01
43037-01
48100-01
481050
46082
45006
43022
04001-37
04021-07
48307
48307-02
48006-03
48307-04
48006-07
48006-06
48114-03
48006-05
04017-16
46725
04021-10
04001-09
46797
Ref. Part
No. No.
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
04041-07
04029-03
48924
48926
04001-01
04020-09
48204
48269
04021-05
04019-04
04004-02
04017-42
04019-05
43277
04041-07
04021-09
45423
46748
48100-02
04050-05
44078
481025
481024
43297
43312
48677
481035
04041-12
04001-108
48098
Description
Flat Washer, 3/8" (.391 x .938 x .105)
Wing Nut, 3/8-16
Pulley
Tapered Hub, 1.125 Bore
Hex Head Bolt, 1/4-20 x 3/4"
Hex Nut, 5/8-11
Belt, Blade Drive
Pulley, Belt Guide
Nut, Center Locknut - 3/8-16
Nut, 3/8-16 Serrated Flange
Support, Belt Cover
Capscrew, 7/16-14 x 1" Serr. Flange
Hex Nut, 7/16-14 Serrated Flange
Spacer, J-Hook
Flat Washer
Nut, 3/8-16 Elastic Stop
Idler Pivot
Idler Arm Assy. (incl. 22 & 58)
Bushing, 1-1/8 x 1.0 Flanged
Retaining Ring, 1-1/8" Ext. "E"
J-Hook
Seal, Cutter Spindle
Seal, Cutter Spindle
Spindle Bushing
Spacer, Outside
Relief Fitting, Cutter Spindle
Nut,
Flat Washer
Hex Head Bolt, 5/16-18 x 1-1/4"
Shield, Spindle
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
19
48", 52", 61", & 72" CUTTER DECKS
83
59
56
51
41
45
44
40
45
44
61
11
83
43
43
11
83
48 45
60
47
61
4
40
39
11
41
62, 62A
63
46
46A
46B
41
22
51
44 58
43
42
65
49
13
61
14
64
74
40
76
9
78
83
63
A
38
36
18
52
73
50
55 54
51
40
37
20
67
57
68
64
22
77
35
19
77
A
35
14
14
51
75
21
50
22
21
8
35
14
20
23
24
2
25
27
66
1
28
80
26
81
79
72
10
5
53
82
7
6
29
34
11
32
31
33
83
11
30
70
12
3
5
15
15A
31
16
71
84
17
SC151G
20
69
48", 52", 61", & 72" CUTTER DECKS
Ref. Part
No. No.
Description
48 52 61 72
1
1
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
15
15
15
15A
15A
15A
16
17
18
19
20
21
22
23
24
25
26
27
28
29
NS
30
31
32
33
34
35
36
36A
37
38
39
39
39
39
40
41
42
42A
42B
43
44
45
46
Cutter Deck (Includes decals)
Cutter Deck (Includes decals)
Cutter Deck (Includes decals)
Cutter Deck (Includes decals)
Spindle Assembly
Sleeve, Cutter Spindle
Pulley
Tapered Bearing (two)
Spindle Housing
Grease Fitting Str. 1/4-28
Spindle Shaft
Idler Pivot
Key, 1/4 x 1/4 x 2"
Spacer, Cutter Blade
Hex Head Bolt, 5/16-18 x 1-1/4"
Spring, Chute Return
Nut, 5/16-18 Serr. Flange
Cutter Blade 16-1/2"
Cutter Blade 18"
Cutter Blade 21"
Cutter Blade 24"
Cutter Blade 16-1/2" High Lift
Cutter Blade 18" High Lift
Cutter Blade 24" High Lift
Flat Washer, (.688 x 1.75 x .134)
Hex Head Bolt, 5/8-11 x 9-1/2"
Caster Assy. (incl. 19-28)
Quick Pin
Spacer, Caster Yoke, 1/2" Thick
Bushing, 5/8 x 1", Flanged
Relief Fitting, Cutter Spindle
Support Assy., (incl. 21-23)
Caster Yoke
Sleeve, Caster Wheel Bearing
Hex Head Bolt, 1/2-13 x 5-1/2"
Nut, 1/2-13 Elastic Stop
Wheel Assy. , (incl. 29-34,81)
Tire Only, Caster Wheel
Inner Tube Only, Caster Wheel
Rim Pair, Caster Wheel
Bearing Retainer, Caster Wheel
Roller Bearing, Caster Wheel
Grease Fitting 45 Deg., 1/4-28
Hub Assy., (incl. Bolts)
Capscrew, 5/16-18 x 3/4"
Discharge Chute
Discharge Chute
Nut, 5/16-18 Elastic Stop
Hex Head Bolt, 5/16-18 x 1"
Belt Cover, (incl. Decals)
Belt Cover, (incl. Decals)
Belt Cover, (incl. Decals)
Belt Cover, (incl. Decals)
Flat Washer, (.391 x .938 x .105)
Wing Nut, 3/8-16
Pulley
Pulley
Pulley
Tapered Hub
Hex Head Bolt, 1/4-20 x 3/4".
Nut, 5/8-11 Hex Head
Pulley, Double
x
46851
46751
46752
46608
46631
43296
48924
481022
43294
48114-04
43298
45037
04063-08
43278
04001-10
481050
04019-03
48110
48108
48111
48112
48184
48185
48304
04040-10
04040-41
46079
04066-01
43037-01
48100-01
48677
46082
45006
43022
04001-37
04021-07
48307
48307-02
48006-03
48307-04
48006-07
48006-06
48114-03
48006-05
04017-16
46726
46725
04021-10
04001-09
46798
46804
46805
46848
04041-07
04029-03
48924
48753
48967
48926
04001-01
04020-09
48923
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Ref. Part
No. No.
46a
46B
47
47
47
47
48
48
48
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
62A
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
48940
48966
48087
48285
48265
48295
48089
48286
48088
48296
04021-05
04019-04
04021-09
04004-02
04001-08
04017-42
04019-05
04041-08
44078
48181
04050-02
46081
48100-05
43028
44078
43077
04041-12
04001-46
481024
46748
43277
481035
43312
43297
04030-03
04001-108
04001-77
45329
48269
48100-02
04050-05
48038
45046
04040-15
48307-08
48098
481025
Description
Pulley, Double
Pulley, Double
Belt,RH Blade Drive
Belt,RH Blade Drive
Belt,RH Blade Drive
Belt,RH Blade Drive
Belt, Blade Drive
Belt, Blade Drive
Belt, Blade Drive
Belt, Blade Drive
Nut, 3/8-16 Centerlock
Nut, 3/8-16 Serr. Flange
Nut, 3/8-16 Elastic Stop
Support, Belt Cover
Hex Head Bolt, 5/16-18 x 3/4"
Capscrew, 7/16-14 x 1" Serr.
Nut, 7/16-14 Serr. Flange
Flat Washer, 3/4 Special
J-Hook
Idler Pulley, "V" Groove
Retaining Ring, 3/4" Ext. "E"
Idler Arm Assy. (incl. 22 & 61)
Bushing, 3/4 x 1/2
J-Hook, Idler Pulley
J-Hook, Idler Pulley
Spacer, Pulley
Flat Washer, 3/8 x 1-1/2 x 16 Ga.
Hex Head Bolt, 3/8-16 x 2-1/4"
Seal, Cutter Spindle
Idler Arm Assy., (incl. 22 & 77)
Spacer, J-Hook
Nut, Cutter Spindle
Spacer, Outside
Spindle Bushing
Lock Washer, 5/16"
Hex Head Bolt, 5/16-18 x 4-1/4"
Hex Head Bolt, 3/8-16 x 3-1/2"
Idler Pivot
Idler Pulley, Clutch Belt
Bushing, 1-1/8 x 1.0 Flanged
Retaining Ring,1-1/8 Ext. "E"
Guide, Roller
Roller Shaft
Flatwshr., 5/16 (.375 x .875 x .083)
Nut, 5/16-24 Tapered
Shield, Spindle
Seal, Cutter Spindle
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
21
48 52 61 72
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
ENGINE DECK
-BV Only
7
97
78
6
4
1
80
7
81
3
8
86
38
ELECTRIC
START ONLY
92
91
BLK
RED
2
9
89
10
85
18
16
35
82
16
11A
13
15
11A
40
21
72
38
77
19
14
88
73
94
11
67
83
12
12A
17
36
KA ONLY
36A
87
96
39
11
22
20
23
98
103
38
79
76, 76A
28
42
44
74
71
70
38
66
38
27
75
46
46A
45
51
26
50
47
38
50
62
47
29
41
68
49
64
32
51
52
52A
61
60
58
59
72
30
31
57
102
25
44A
63
84
93
43
72
73
69
95
41
65
73
72
24
39
40
54
55
33
48
37
90
34
53
56
SC152G
22
ENGINE DECK
14KA 14KH 16BV 20CVE
14KA 14KH 16BV 20CVE
Ref. Part
No. No.
1
1
1
1
1
1
1
1A
1B
2
3
4
5
6
7
8
9
10
11
11A
12
12A
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
36A
37
38
39
40
41
42
43
44
44A
45
46
46A
47
48
49
14KAE
Description
48842
Engine 14KA Kawasaki
481052
Engine 14KAE Kawaski
48844
Engine 14KH Kohler
481065
Engine 16BV Briggs Vanguard
48766
Engine 16BVE Briggs Vanguard
481066
Engine 18BV Briggs Vanguard
48971
Engine 20CVE Kohler Command
481067
Exaust System, BV Engine
481068
Debris Guard, 18HP BV
04050-10 Retaining Ring, 1/2" Ext. "E"
04020-02 Hex Nut, 1/4-20
04010-10 Screw, 1/4-20 x 2" Rnd. Hd. Phil.
421239
Strap, Fuel Tank
48311
Cap, Fuel Tank
48292
Pad, Rubber-Fuel Tank - Upper
46846
Fuel Tank Assy. (incl. 9, 10)
48309
Bushing
48308
Valve, Fuel Shut-off
48059-01 Clamp, Fuel Hose
48059-02 Clamp, Fuel Hose, (KA Only)
48058
Fuel Hose, 1/4 ID x 20" KA, BV
48058
Fuel Hose, 1/4 ID x 23"
48028-05 Cable Tie
48057-02 Fuel Filter
48179
Fuel Hose, 7/32 ID x 3-1/2"
04015-06 Capscrew, #10-32 x 1 Soc. Hd.
46323
Lever Assy., Pump Control -LH
46324
Lever Assy., Pump Control -RH
46439
Battery Box Kit
48015
Battery
04001-44 Bolt, 1/4-20 x .50"
04020-02 Nut, 1/4-20
48099
Pad
42392
Battery Cover
04029-01 Wing Nut, 1/4-20
45685
Battery Support
48661
Pad, Rubber
04003-01 Bolt, 1/4-20 x 6" Carriage
48468-05 Hub, Wheel (incl. 34)
4810-81 Wheel Assy., (incl. 29,31,32,34)
481081-02 Tire, 16 x 6.50, 4 ply
48004-04 Rim Assy
48679
Hex Castle Nut, 3/4-28 UNEF
48004-06 Nut, Lug
48205
Pad, Rubber-Fuel Tank, Lower
46946
Engine Deck, 16" Wide, W/Decls.
46947
Engine Deck, 20" Wide, W/Decls.
04063-15 Key, 3/16 x 3/16 x .75
04019-03 Nut, 5/16-18 Serr. Flange
04001-11 Bolt,5/16-18 x 1-1/2" Hex Head
04019-02 Nut, 1/4-20 Serrated Flange
04019-04 Nut, 3/8-16 Serr. Flange
04017-18 Capscr., 5/16-18 x 1.25 Sr. Flg.
04001-22 Bolt, 3/8-16 x 2-3/4" Hex Head
04030-04 Lockwasher, 3/8
04001-19 Bolt, 3/8-16 x 1" Hex Head
04001-46 Bolt, 3/8-16 x 2-1/4"
04063-01 Key, 1/4 x 1/4 x 1.25"
04063-20 Key, 1/4 x 1/4 x 1.0"
04012-04 Setscrew, 5/16-18 x 3/8"
48437
Wheel Motor
48988
Pulley, Pump Drive Engine
Ref. Part
No. No.
16BVE
18BV
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
50
51
52
x
52A
x
53
x
54
x
55
x
56
x
57
x
x
58
x
x
59
x
x 60
x
x
61
x
x
62
x
x
63
x
x
64
x
x
65
x
x
66
x
67
68
x
69
x
70
x
x
71
72
73
x
74
x
x
75
x
x
76
x
x
76A
x
x
77
x
x
78
x
x
79
x
x
80
x
x
81
x
x
81A
x
x
82
x
x
83
x
x
84
x
x
85
x
x 86
x
x 87
x
x
88
x
x
89
x
x
90
x
x
91
92
x
x 92A
x
x
92B
x
x
93
x
x
94
x
x
95
x
x 96
x
x
97
x
x
98
x
x
98
x
x
99
x
x
99
x
100
x
101
x x
102
x x
102
x x
103
14KAE
04063-14 Key, 5.0 x 5.0 x 25mm
48586
Pulley, Pump Shaft
48553
Belt, Pump Drive
48587
Belt, Pump Drive
48786
Electric Clutch
04041-18 Flat Washer,7/16
04030-05 Lock Washer, 7/16
04001-93 Hex Head Bolt, 7/16-20 x 3"
04001-13 Hex Head Bolt, 5/16-18 x 2.75"
421564
Backing Plate, Clutch Stop
48814
Rubber Pad, Clutch Stop
04040-15 Flat Washer, 5/16
04001-10 Hex Head Bolt, 5/16-18 x 1-1/4"
04041-07 Flat Washer, 3/8
48473
Pulley, Idler Pump Drive
04021-05 Nut, 3/8-16 Center Lock
04001-08 Hex Head Bolt, 5/16-18 x .75"
48051
Spring, Pump Belt Idler
04040-14 Flat Washer, 1/4
04050-02 Retaining Ring, 3/4 Ext. "E"
48114-04 Grease Fitting, Str. 1/4-28
45212
Pivot, Idler Arm
46467
Idler Arm, (incl. 69 & 84)
04021-10 Nut, 5/16-18 Elastic Stop
48030-09 Clamp
04003-04 Carrage Bolt, 5/16-18 x 1"
421370
Clutch Bracket
04017-19 Capscr, 5/16-18 x 1.50" Sr. Flg.
04002-01 Metric HH Bolt, M8-1.25 x M30
04003-08 Carrage Bolt, 5/16-18 x .75"
04031-09 Lock Washer, 5/16 Int. Tooth
04030-03 Lock Washer, 5/16
48257
Pipe Cap
48402-04 Pipe,4.75" Nipple
48402-03 Pipe, 5.25 Nipple
04003-09 Carrage Bolt, 1/4-20 x 1-1/4"
48029-06 Starter Cable, 18" Red
48100-05 Bushing, 3/4 Sintered
48016
Solenoid
45283
Shaft Weldment, RH Pump Cntl.
421390
Bracket, Capacitor
**
Condenser (order from Kaw. )
04003-02 Carrage Bolt, 1/4-20 x 3/4"
04061-03 Cotter Pin, 3/32 x 1.25"
48029-02 Battery Cable, 31.5" Red
48029-15 Battery Cable, 36" Black
48029-14 Battery Cable, 31.5 Black
48029-11 Battery Cable, 27" Black
421703
Battery Box
48126
Rubber Boot
04003-12 Carrage Bolt, 5/16-18 x .75
48030-10 Cable Clamp, .75 ID
04002-07 Metric H H Bolt, 8-1.25 x 10
45418
Pulley Guard, 16" Frame
45419
Pulley Guard, 20" Frame
481077
Wire Hrns. Adapter, Man. Start
481054
Wire Hrns. Adapter, Elec. Start
04021-08 Nut, 1/4-20 Elastic Stop
04019-03 Nut, 5/16-18 Serrated Flange
04041-08 Washer, 3/4-.766 x 1.2 x .06
04041-08S Washer, 3/4-.766 x 1.2 x .035
****
Regulator, (order from Kaw.)
** Kawasaki condenser part number is 21013-2064. Order from your Kawasaki dealer or distributor.
**** Kawasaki voltage regulator part number 21066-2071. Order from your Kawasaki dealer or distributor.
23
16BVE
Description
18BV
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
HANDLE ASSEMBLY
16
74
17
75
19
19A
11
71
68
15
76
16A
6
18
18A
8
7
11
2
12
9
17
13
20
19
19A
5
4
3
1
10
21
22
23
24
15
14
26
77
41
33
34
35
37
31
32
3
36
40
38
29
11
78
37
27
11
24
16A
3
28
30
32
34
67
60
69
45
61
40
66
42
39
39A
40
63
63A
37
43
65
60
25
43
49
60 48
47
61
44
46
38
64
64A 24
51
3
52
59
61
73
56 55
58
62
57
11
54
24
72
56
55
50
53
70
73
SC153G
HANDLE ASSEMBLY
14KA 14KH 16BV 20CVE
14KA 14KH 16BV 20CVE
Ref. Part
No. No.
1
1
2
3
4
5
6
7
8
9
10
11
12
13
13A
14
15
16
16A
16A
17
18
18A
19
19A
20
20A
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
39A
40
41
42
43
44
45
46
47
48
14KAE
Description
46802
Upper Handle Wlmt. W/Decals
x
46857
Upper Handle Wlmt. W/Decals
x
42675
Quadrant, Speed Control
x
04062-02 Hairpin, .094 x 1.19
x
45282
Lever, Speed Adjustment
x
43086
Bushing, Speed Adjustment Lever x
04001-20 Hex Head Bolt, 3/8-16 x 1-1/2"
x
48493-01 Ball Plunger
x
48092
Knob, Speed Adjustment
x
04014-01 Capscrew, 1/4-20 x 3/4" FHHS
x
04021-08 Nut, 1/4-20 Elastic Stop
x
04021-10 Nut, 5/16-18 Elastic Stop
x
04010-01 Screw, #10-32 x 1/2" PW HD
x
481071 Throttle Control
x
48946
Throttle Control
04019-01 Nut, #10-32 Serr. Flange
x
48312
Bushing
x
45572
Handle, Operator Presents-RH
x
45571
Handle, Operator Presents-LH (20") x
45573
Handle, Operator Presents-LH (16") x
48787
Switch,Elec.Clutch Eng. (incl.Nut) x
481076 Wire Harness, Manual Start
x
481055 Wire Harness, Electric Start
x
48609
Key Switch, Manual Srt. (incl. Hwd) x
48798
Key Switch, Elec. Start (incl. Hwd.) x
42257-01 Neutral Latch-RH
x
42257-02 Neutral Latch-LH
x
48717
Switch, Neutral Interlock
x
48159
Grip
x
04032-01 Washer, Curved Spring
x
04040-15 Flat Washer
x
04031-08 Lock Washer,1/4" Int. Tooth
x
04001-17 Hex Head Bolt, 5/16-18 x 2"
x
04001-53 Hex Hd. Bolt, 5/16-18 x 2-1/2"
x
46744
Lever, Steering Control (incl. 29)
x
48492
Grip, Steering Control
x
44050
Rod, Steering Control
x
48951
Spring, Handle Return
x
04017-27 Capscr., 3/8-16 x 1" Ser. Flange
x
04030-02 Lock Washer, !/4"
x
04019-04 Nut, 3/8-16 Serr. Flange
x
44051
Rod Steering Control
x
45279
Bellcrank, Speed Control
x
04012-02 Setscrew, 1/4-28 x 1/4"
x
46335
Cam, Speed Control (incl. SS)
x
43166
Jackshaft, Speed Control
x
43155
Jackshaft, Speed Control
x
04063-13 Key, 1/8 x 1/2" Woodruff
x
04021-10 Nut, 3/8-16 Elastic Stop
x
46336
Pivot, Pump Ctrl. (incl.Bshg & Zrk) x
48100-04 Bushing, 1/2" ID
x
04017-17 Capscrew, 5/16-18 x 1" Serr. Flg. x
04019-03 Nut, 5/16-18 Serrated Flange
x
42730
Bar, Speed Control
x
43161
Spacer, Speed Ctrl. Bearing
x
48409
Bearing, Speed Ctrl. Bellcrank
x
Ref. Part
No. No.
16BVE
18BV
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
63A
64
64A
65
66
67
68
69
69A
70
71
72
73
74
75
76
77
78
14KAE
04001-69 Hex Head Bolt, 5/16-18 x 1-3/4"
48494-02 Spring, Return
481092-01 Knob, Plastic
43308
Bushing
45292
Handle, Neutral Adj
04065-05 Drive Pin, 5/32 x 7/8 Type U
04001-08 HH Bolt,5/16-18 x 3/4"
04030-03 Lock Washer, 5/16
04019-03 Nut, 5/16-18 Serr. Flange
48224
Bearing, Ball Neutral Return
46747
Cam, Neutral (incl. grease ftng.)
48114-05 Grease Fitting, 1/4-28 UNF
04050-01 Retaining Ring, 5/8 Ext. "E"
04001-09 Hex Head Bolt, 5/16-18 x 1"
45295
Shaft, Pump Control-LH
45283
Shaft, Pump Control-RH
45642
Bellcrank, Pump Control-LH
45643
Bellcrank, Pump Control-RH
04050-10 Retaining Ring, 1/2 Ext. "E"
48026
Switch, Neutral Start
By Ref.
Deck, Engine
04001-10 Hex Head Bolt, 5/16-18 x 1-1/4"
481278
Choke Control
481072
Choke Control
481057
Spring, Return
42413
Fuse Holder
43306
Swivel Joint, Steering Rod
04040-04 Flat Washer (.344 x .688 x .065)
48298
Blade Fuse, 20A
04021-01 Nut, #10-32 Elastic Stop
04010-03 Screw, #10-32 x 1-1/2" Phillips
43305
Pin, Neutral Lock
43032
Swivel Joint
18BV
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
25
16BVE
Description
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
HYDRAULIC ASSEMBLY
1
2
K
B
5
B
E
21
13
4
13
4
29
8
3
30
7
4
E
5
12
31
A
5
13
23
22
10 28 11
4
22
D
6
D
C
C
20
10
J
10
19
H
J
18
18A
11
H
17
28
24
32
3
A
13
7
4
6
15
4
14
16
10
29
8
28 11
K
19
33
12
28
10
34
11
10
9
F
G
26
25
FG
10
10
19
19
21
27
SC154G
26
HYDRAULIC ASSEMBLY
Ref. Part
No. Number
1
2
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
18A
19
20
21
22
23
24
25
25
26
27
28
29
30
31
32
33
34
48535
46618
46619
48484-01
43853-02
48482
48350-04
48603-06
48551
04003-11
481265
48603-02
48350-03
48482
48471-02
48489-02
43096
48353-01
04017-16
04017-22
48603-04
48486-01
04019-03
48351
48352-02
04003-12
46767
46768
04019-04
48462-01
48485-01
48603-03
48352-03
48491
48731-01
04010-10
04021-08
Description
14KA 14KAE 14KH 16BV 16BVE 18BV 20CVE
Cap, Oil Reservoir
Oil Reservoir
Oil Reservior
Elbow, 90 deg. Female 1/4 NPT to 1/4 JIC Male
Coupling, 7/16-20 SAE Flare Swivel to 1/4" Hose Push On
Hose, 1/4" ID - 12" Long (Order By The Inch)
Elbow, 90 deg. 7/16-20 JIC to 9/16-18 "O" Ring
O-Ring
Pump, Sunstrand BDP-10L117
Bolt, Carriage, 3/8-16 x 1-1/4
Hose, Pump to Motor
O-Ring
Elbow, 90 deg., 7/16-20 JIC x 7/16-20 O-Ring
Hose, 1/4" ID - 10" Long (Order By The Inch)
Oil Filter Base
Elbow, 90 deg. Male 3/4-16 JIC to 1/2" Male NPT
Spacer, Oil Filter Base (20" Frame)
Coupling, 3/4-16 SAE Flare Swivel to 1/2" Hose Push On
Capscrew, 5/16-18 x .75" (For 16") Serr. Flange
Capscrew, 5/16-18 x 2.25" (For 20") Serr. Flange
O-Ring
Elbow, 90 deg. Male 1/4 NPT to 1/4 Hose Push On
Nut, 5/16-18 Serr. Flange
Hose, 1/2" ID, 12" Long (Order By The Inch)
Coupling, 1/4 straight Male NPT to 1/4 Hose Push On
Bolt, 5/16-18 x 3/4" Carriage
Engine Deck (16" Wide) W/Decals
Engine Deck (20" Wide) W/ Decals
Nut, 3/8-16 Serr Flange
Oil Filter
Elbow, 45 Deg.-3/4-16 JIC Male x Male 3/4-16 O-Ring
O-Ring
Coupling, 3/8 Straight Male NPT to 1/2 Push-on
T-Fitting, 3/8 NPT
Plug, 3/8-18 NPTF Magnetic
Screw, 1/4-20 x 2.0" Round Head Philips
Nut, 1/4-20 Elastic Stop
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
27
HYDRAULIC PUMP ASSEMBLY
30
ea
lS
u
rha
26
it
lK
25
e
Ov
24
23
22
27
28
1
29
19
20
21
17
16
3
15
18
11
2
14
12
13
5
6
7
8
11
10
9
4
SC165G
28
HYDRAULIC PUMP ASSEMBLY
Ref. Part
No. Number
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Housing Kit (Incl. Housing, Journal Bearing)
End Cap
Straight. Headless Pin
Socket Head Screw
End Cap Gasket
Charge Pump Kit (Incl. Charge Cover, Gerotor Assy., O-Ring)
Gerotor Assembly
O-Ring
Charge Relief Valve Kit
Socket Head Screw
Check Valve Kit (Incl. Check Plug, Spring, O-Ring, Orfice Check Valve)
Bypass Valve Kit (Incl. Bypass Valve, O-Ring, Back-up Ring)
Backup Ring
Cylinder Block Kit
Block Spring
Block Thrust Washer
Roller Thrust Bearing
Swash Plate
Trunnion Arm
Guide Slot
Cradle Bearing
Lip Seal
Pump Shaft
Ball Bearing
Retaining Ring
Lip Seal
Retaining Ring
Spacer
Shaft Kit (Incl. Pump Shaft, Ball Bearing, Retaining Ring)
Overhaul Seal Kit (Incl. Gasket, Trunnion Seal, Input Shaft Seal, Charge Pump O-Ring)
HG 2513017
HG 2513016
HG 9004800-2506
HG 9007314-0810
HG 2003067
HG 2513027
HG 50273
HG 9004101-1340
HG 2510011
HG 50095
HG 2510027
HG 2513030
HG 9006110-0120
HG 70079
HG 2003014
HG 2003017
HG 2003044
HG 2003087
HG 2003005
HG 2000015
HG 2003023
HG 9008000-0126
HG 2003020
HG 2003043
HG 2003016
HG 9008000-0128
HG 2003052
HG 2003018
HG 2513038
HG 2513018
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
29
NEUTRAL
INTERLOCK
REGULATOR
RED
RED
ENGINE
A
F
B
G C
H
D
RED
BLACK
BLACK
BLUE
WHITE
WHITE
YELLOW
INSTRUMENT
PANEL HARNESS
BLADE
CLUTCH
BLACK
E
Wire Harness Eng. Deck - KA
481074
SC155G
GROUND
Wire Harness, Engine Deck - KAE
481051
30
BLADE
CLUTCH
Wire Harness Eng. Deck - KH/BV
481073
NEUTRAL
INTERLOCK
E
A
F
B
G
C
H
D
GROUND
BLACK
RED
BLACK
BLUE
WHITE
WHITE
YELLOW
SC156G
ENGINE
INSTRUMENT
PANEL HARNESS
TRANSMISSION
ENGINE
GROUND
TO ENGINE
RED
RED
E
A
F
B
G C
H
D
GREEN
BLACK
BLUE
WHITE
WHITE
YELLOW
BLACK
ELECTRIC
CLUTCH
TO INSTRUMENT
PANEL CONNECTOR
Wire Harness Engine Deck-20CVE
481075
STARTER
SOLENOID
31
SC158G
Wire Harness Eng. Deck - 16BVE
481014
FUSES
RELAY
MOWER
ENGAGE
KEYED
SWITCH TERMINAL
KEY
SWITCH
Handle Wire Harness - Electric Start
RED
YELLOW
BLACK
GREEN
WHITE
WHITE
481267
RED
GREEN
BLACK
RED
A
E
B
F
C G
BLACK
TO
OPERATOR
PRESENCE
SWITCH
YELLOW
YELLOW
BLACK
BLUE
WHITE
YELLOW
RED
RED
NEG
HOURMETER
BLACK
KEY SWITCH
MOUNTING
POS
HOURMETER
SC159G
BLACK
MOWER ENGAGE
SWITCH MOUNTING
32
D
H
TO ENGINE
DECK WIRE
HARNESS
Handle Wire Harness - Manual Start
481266
MOWER
ENGAGE
SWITCH
KEY
SWITCH
KEYED
TERMINAL
F
A
B
C
WHITE
RED
BLACK
RED
BLACK
BLUE
WHITE
BLACK
TO
OPERATOR
PRESENCE
SWITCH
NEG
HOURMETER
YELLOW
YELLOW
A
E
B
F
C
G
D
H
TO ENGINE
DECK WIRE
HARNESS
POS
HOURMETER
BLACK
BLACK
SC157G
KEY SWITCH
MOUNTING
MOWER ENGAGE
SWITCH MOUNTING
WIRE HARNESS WITH RELAY
PART NO. 481275
To Engine
Ground
RELAY
BLACK
GREEN
To Starter
BLUE
RED
SC481275
To Blue Wire
From Engine
To Starter
Red Battery
Cable Post
33
REPLACEMENT DECALS & INFORMATION
48072
48314
WARNING
ROTATING BLADES AND BELTS
36" - 48316
48" - 48318
52" - 48319
61" - 48320
72" - 48327
48071
KEEP HANDS, FEET & CLOTHING CLEAR
KEEP ALL GUARDS IN PLACE
SHUT OFF ENGINE & DISENGAGE BLADE
CLUTCH BEFORE SERVICING
CLEAR AREA OF DEBRIS BEFORE MOWING
USE CAUTION IN DIRECTING DISCHARGE
KEEP BYSTANDERS, CHILDREN & PETS AWAY
READ INSTRUCTION MANUAL BEFORE OPERATING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING
481040
KIT, OR ENTIRE GRASS CATCHER INSTALLED
481040
481122
CHOKE
MANUFACTURED UNDER ONE OR MORE
OF THE FOLLOWING PATENTS:
R
FAST
4,991,382
4,998,948
4,118,617
4,487,006
4,885,903
4,920,733
4,967,543
PATENTS PENDING
SLOW
48656
481122
CAUTION
MOWER DECK ON
A FT O F M A
PROUDLY
MADE
INUSA
✩
ON
KEEP BYSTANDERS AWAY
481121
✩
M
MOWER DECK OFF
PULL BACK
TO DISENGAGE
OFF
AY
WARNING
WARNING
INSTALL BELT COVER BEFORE
OPERATING MACHINE
FALLING HAZARD
USE ONLY SCAG APPROVED
RIDING ATTACHMENTS
SEE OPERATOR'S MANUAL
V IL L E ,W
48873
481121
MOUNT RIDING
ATTACHMENT
HERE
READ OPERATOR'S MANUAL
481109
481039
481109
34
IL L E
CAUTION
PULL UP AND
PUSH FORWARD
TO ENGAGE
CR
YV
M ET A
L
R
BEFORE OPERATING
READ OPERATINGS
MANUAL AND SAFETY
INSTRUCTIONS
481039
I
REPLACEMENT DECALS & INFORMATION
CHOKE
FAST
START
STOP
SLOW
481270
FAST
START
STOP
SLOW
481271
TRACKING ADJUSTMENT
CONTROL ROD
ADJUSTMENT
FAST
TRANSMISSION
OIL 481125
REVERSE
NEUTRAL
ADJUSTMENT
FORWARD
481125
SEE OPERATOR'S MANUAL
SPEED
CONTROL
481080
SLOW
N
NEUTRAL
481124
481124
48514 - 20"
48555 - 16"
35
LIMITED WARRANTY-COMMERCIAL EQUIPMENT
Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment
of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer
without charge for parts and labor. This warranty is limited to the original purchaser and is not transferable. Proof of
purchase will be required by the dealer to substantiate any warranty claims. All warranty work must be performed by an
Authorized Scag Service Dealer.
This warranty is limited to the following specified periods from the date of the original retail purchase for defects in
materials or workmanship:
* Wear items including drive belts, blades, hoses and tires are warranted for 90 days.
* Batteries are covered for 90 days.
* Frame, deck, and structural components including oil reservoir, fittings, and oil cooler
are warranted for 1 year.
* Engines and electric starters are covered by the manufacturer’s warranty period.
* Drive system components are warranted for 1 year by the component manufacturer, in
conjunction with Scag Power Equipment. (Excluding fittings, hoses, cooling system,
oil reservoir, drive belts).
* Electric clutch components are warranted for 1 year.
* Cutter Spindle Assemblies 46631 have a Limited Warranty for three years (Parts and
labor 1st year; Parts only 2nd and 3rd year).
Any Scag product used for rental purposes is covered by a 90 day warranty.
The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty
period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner
after repair will be paid for by the owner. Scag’s responsibility is limited to making the required repairs and no claim of
breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.
This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has
been operated in any way contrary to the operating instructions as specified in the Operator’s Manual. The warranty
does not apply to any damage to the mower that is the result of improper maintenance, or to any mower or parts that have
not been assembled or installed as specified in the Operator’s Manual and Assembly Manual. The warranty does not
cover any mower that has been altered or modified, changing performance or durability. In addition, the warranty does
not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or durability.
Scag Power Equipment reserves the right to change or improve the design of any mower without assuming any obligation
to modify any mower previously manufactured.
All other implied warranties are limited in duration to the one (1) year warranty period or ninety (90) days for mowers used
for rental purpose. Accordingly, any such implied warranties including merchantability, fitness for a particular purpose,
or otherwise, are disclaimed in their entirety after the expiration of the appropriate one year or ninety day warranty period.
Scag’s obligation under this warranty is strictly and exclusively limited to the repair or replacement of defective parts and
Scag does not assume or authorize anyone to assume for them any other obligation. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may not apply to you.
Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for
gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the owner,
mechanic’s travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are being
performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time or inconvenience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
© 1998
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE, INC.
PART NO. 03031
REVISION 1 PRINTED 1/98
PRINTED IN USA