Download Craftsman 358.350060 Operator`s manual

Operator's Manual
CRRFTSMRN
2.2 cu. in./36cc 2-Cycle
GASOLINE CHAIN SAW
Model No.
358.350060 - 16 in. Bar
Read and follow all Safety Rules and Operating
WARNING:
Instructions before first use of this product.
61_
•
For
to your
questions
thispm,
product:
Call answers
7 am-7 pm,
Mon.--Sat.,
or about
10 am-7
Sun.
1-800-235-5878
(.ou_===.c..=_m.)
|
_ars, Roebuck and Co., HoffmanEstates,IL 60179 USA
530087821 07/17/98
Warranty
Safety Rules
Assembly
Operation
.....
Maintenance
Service and Ad_stmbt_s _. :
2
2
5
6
11
14
FULL ONEYEARWARRANTY
CHAIN SAW
Storage '
Trouble Shooting Chart
Parts List
Spanish
Parts & Ordering
16
17
20
24
Back
ON CRAFTSMAN ® GAS
For one year from the date of purchase, when this Craftsman Gas Chain Saw is
maintained, lubricated and tuned up accordingto the owner's manual, Sears will
repair, free of charge, any defect in matodai or workmanship.
This warranty excludes the bar, chain, spark plug and air filter,which are
expendable parts, and become wom dudng normal use.
If this Gas Chain Saw is used for commercial or rental purposes, this warranty
applies for 30 days from the date of purchase,
WARRANTY SERVICE IS AVAILABLE BY RETURNING THIS CHAIN SAW TO
THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES.
This warranty gives you specific legal dghts, and you may also have other rights
which vary from state to state.
Soars, Roebuck and Co., D/817 WA, Hoffmen Eetatda,.IL 60179
duty, non-slip gloves;eye protection
such as non,-tfogglng,
vented goggles
or face screen; an approved safety
hard hat; and sound barriers (ear
_lugs or mufflers) to protect your
esdng. Regular users should have
hsadng checked regularlyas chain
saw noise can damage headng. Secure hair above shoulder length.
• Keep all parts of your body away from
the dlain when the engine is runntng.
• Keep children,bystanders, and animals at least 30 feet (10 meters)
Headng
_
SafetyHat
away from the work area when startPrctecUon
-,_ _
_
Eye
ing and using the saw.
ilOOr,---- Protection
• Do not handle or operate a chain saw
HeavyDuty
when you are fatigued, Ill,or upset, or
Gloves
if you have taken alcohol, drugs, or
medication. You must be In good
_fhysical conditionand mentally alert.
S-,tety
SafetyChaps
you have any condition that might
Shoes
be aggravated by strenuous work,
check with doctorbefore operating.
_IIII
• Do not start cutting untilyou have a
clear work area, secure footing, and
• Wear protective gear. Always use
especially ifyou are felling a tree, a
.. __.eel-toed safety footwear with nonslip soles; snug-fittingclothing; heavyretreat path.
2
WARNING: Always disconnect spark
plugwire when making repairs except
for carburetor adjustmi_nts.Because a
chain saw is a high-speed woodcutting
tool, careless or improper use of this
tool can cause serious injury.
PLAN AHEAD
• Restrictthe use of your saw to adult
users who understand and can follow
the safety rules, precautions, and operating Instructionsfound in this
-_-._nanuai.
\
OPERATEYOUR SAW SAFELY
• Do not operate with one hand. Sedous injury to the operator, helpers, or
bystanders may resultfrom onehanded operation. A chain saw is Intended for two-hand_ld use. ....
• Operate the chain saw only in a wellventilated outdoor area.
• Do not operate saw from a ladder or
in a tree, unless you are specifically
trained to do so.
• Make sure the chain will not make
contact with any object while starting
the engine. Never tryto start the saw
when the guide bar is in a cut.
• Do not put pressure on the saw, sspecially at the end of the cut. Doing
so can cause you to lose control
when the cut is completed.
• Stop engine before setting saw down.
• Hand carry saw only when engine is
stopped. Carry with muffler away from
body.guide bar & chain projectingbehind you; guide bar preferably covered with a scabbard.
• Store the unit and fuel in e cool, dry
well ventilated space where fuel vapors cannot reach sparks or open
flames from water heaters, electdc
motors or switches, fumaces, etc.
GUARD AGAINST KICKBACK
Follow eli safety rules to help avoid
kickback and other forces which can
resultin serious injury.
Avoid
Obstructions
ClearThe WorkingArea
WARNING: Rotational Kickback can
occur when the moving chain contacts
an object at the upper portion of the tip
MAINTAIN YOUR SAW IN GOOD of the guidebar.Contaotat the upper
WORKING ORDER
• Have all chain saw sewice performed
by a qualified service dealer except
the items listed in the maintenance
section of this manual.
• Make certain the saw chain stops
moving when the throttle trigger is released. For correction, refer to CarburetorAdjustments."
• Keep the handles dry, clean, and free
from oil or fuel mixture.
• Keep cape and fasteners securely
tightened.
• Use only Craftsman accassodss and
replacement parts as recommended.
Never modify your saw.
HANDLE FUEL WITH CAUTION
• Do not smoke while handling fuel or
while operating the saw.
• Bi_
all sourcssof sparks orflame
In amss where fuel Is rnixedor poured.
• Mix and pour fuel in an outdoor area
and use an approved, marked container for all fuel purposes. Wipe up
all fuel spills before starting saw.
• Move at least 10 feet (3 meters) from
• fueling site before starting.
.,Tu_the engine off and let saw cool in
a non-oombusltblearea, not on dry
leaves, straw, paper, etc. Slowly remove fupl cap and refuel unit.
portion of the;tip of the guide bar can
cause the cHainto dig into the object,
which stops the chain for an instant.The
resultis a lightningfast, reverse reaction
which kicksthe guide bar up and back
toward the operator.
Pinch-Kickbackand Pull-In occur when
the chain is suddenly stopped by being
pinched, caught, or by contacting a foreign object in the wood. This sudden
stopping of the chain results in a reversal of the chain force used to cut wood
and causes the saw to move in the opposite direction of the chain rotation.
Pinch-Kickback drivesthe saw straight
back toward the operator. Pull-in pulls
the saw away from the operator.
REDUCE THE CHANCE OF
KICKBACK
• Recognizethat Idckbaskcan happen.
With a basic undemtsn_ng of kickback,
you can reduce the element of sufprisa
whichccntributes to accidents.
Never let the moving chain contact
i any object at the tip of the
bar.
Keep warldngarea free from obstructions such as other trees, branches,
rocks, fences, stumps, etc. Eliminate
or avoid any obstructionthat your saw
chain could hitwhile cumng.
• Keep saw chain sharp andpropedy
tensioned.A loose or dull chain can
Dgu_de
increase the chance of kickback. Follow manufacturer's chain sharpening
end maintenance Instructlons. Check
tension st regular Intervals, but never
with engine running. Make .surebar
damp nuts are securely ttgmaneo.
• Begin and continue cuttingat full
speed. If the cbaln is+movingat a
slower speed, "thereis greater chance
of kickback occurring,
• Use extreme caution when reentanng
a cut.
• Do not attempt cuts starling withthe
tip of the bar(plunge cuts).
• Watch for shifting logs or other forces
that could close a cut and pinch or fall
into chain.
• Use the specified Reduced-Kickba.ek
Guide Bar and Low-Kickbank Chain.
Avoid Pinch-Kickback:
• Be extremely aware of situations or
obstructions that can cause matedal
to pinch the top of or otherwise stop
thechain.
• Do not cut more than one log at a
time.
• Do not twist saw as bar is withdrawn
from an undercut when bucking.
Avoid Pull-In:
• Always begin cutting with the engine
at full speed and the saw housing
against wood.
• Use wedges made of plastic or wood.
Never use metal to hold the cut open.
MAINTAIN CONTROL
Stand to the left of the saw
keep your body from being in a direct
line with the cutting chain.
• Stand with your weight evenly balarmed on'both feet.
• Do not overreach. You could be drawn
orthrown offbalance and losecontrol
• Do not cut above shoulder height. It is
difficultto maintain control of saw
above shoulder height.
KICKBACK SAFETY FEATURES
WARNING: The followingfeatures are
Includedon your saw to help reduce
hazard of kickback;however, such features will not totally eliminate this danger. Do not rely only on safety devices.
• Handguard: designed to reduce the
chance of your left hand contacting
the chain if your hand slips off the
front handlebar.
• Position of front and rear handlebars:
designed with distance between handles and "in-line"with each other.The.
spread and "in-line" position of the
hands provided by this design work
together to give balance ano resistance in controlllngthe pivot of the
saw back toward the operator if kickback occurs.
• Reduosd-IOckback Guide Bar: designed with a small radius tip which
reduces the size of the kickback dangdarzone. This type bar has been
emonstrated to significantlyreduce
the number and seriousness of kmckbacks when tested in accordance with
ANSI B175.1.
_'_.
Thumbon
\l_
"
SmellRadius
_L% _'f_kTipGuideBar
Lerg. Radius I
J
• Low-Kidd_k Chain:has met kickback
" " locked
performancerequirements,when tested
on a represe_
sampJeof chain
NeverreversehandposilJon.s
saws below 3.8 cubicinch
• A good, firm grip on the saw with both
displacementsLy:iliad in ANSI B175.1.
hands will help ,you maintain control.
Low:Kickback
Chain
Don't tet go Grip the rear handle with
Contoured Depth Gauge
your right hand whether you are dght
or left handed. Wrap the fingers of
DeflectsKickback
your left hand over and around the
ForceAndAllows
front handlebar, and your leftthumb
_,_.,._
WoodTo
longat_:lGradually
GuardUnk
under the front handlebar. Keep your
Ride Into Cutter
leftarm straight with the elbow locked.
SAFETY NOTICE; Exposure to
• Position your left hand on the front
handlebar so it Is in a straight line with vibrations through prolonged use of
-your right hand on the rear handle
gasoline powered hand tools could
cause blond vessel or nerve damage in
--_-_whanmaking bucking cuts. Stand
the fingers, hands, and joints of people
slightlyto the leftside of the saw to
TipGulde Bar I
4
muffler and spark arresting screen
prone to clmuledlon dbgrdem or .
abnormal swalling. Prolonged use m
whl..chmasts the requirements of
cold weather has been linked to blood
Cal,fom,a Codes 4442 and 4443. All
vessel i_arnagein otherwise healthy
U.S. forest land and the states of
people. If symptoms occur such as
California, Idaho, Maine, Minnesota,
numbness, pain, loss of strength,
New Jersey, Oregon, and Washington
change in aldn color or texture, or loss
require by'law tl]at many Internal
of fee-lingin the fingem, honds, or joints, combustioneng,nas be equipped with a
discontinuethe use or_his to01and
spa_karrestor screen. If you operate a
seek medical attention. An
chain saw in • state or locale where
anti-vibrationsystem does not
such regulations exist, you are.legally
guarantee the avoidance of these
responsiblefor maintaining the
problems. Users who operate power
operating condition of these parts.
tools on a continual and regular basis
Failure to do so is a violationof the law.
must closely monitor their physical .
condition and the condition of this tool. Refer to Customer Responsibilities
CHAIN BRAKE If this saw is to be used chart in the MAINTENANCEsection.
for commercial logging, you must order STANDARDS: This chain saw is listed
and install a chain brake to complywith by Underwdtam Laboratories, Inc. in
accordance with American National
Federal OSHA Regulations for ComStandards for Gesoline-Powemd Chain
memial Logging. Conteot your Sears
Service Center or call 1-P-nn-'.800-235-5878.
Saws Safety Requirements (ANSi
SPARK ARRESTOR: Your saw is
B175.1-1991).
equipped with a temperature limiting
CARTON CONTENTS
Check carton contents against the following list.
Model 358.350060
• Chain Saw (fully assembled)
• Bar tool
• Gloves
• Gas Can
• Bar & Chain Lube
• 2-cycle engine oil
• Chain
: Carrying Case
Examine parts for damage. Do not
usedamagedparts.
• If you nsed_essistanceor find that
parts are missingor damaged, please
call 1-800-235-5878.
NOTE: It is normal to hear the fuel filter
rattle in an empty fuel tank.
Your unit has been factorytested and
the carburetorprecisely adjusted. As e
resultyou may smell gasoline or find a
drop of oil/fuel residue on the muffler
when you unpack the unit.
ASSEMBLY
Your saw is fully assembled; no
assembly is necessary.
R
KNOW YOUR SAW
READ THIS OPERATOR'S MANUAL AND SAFETY RULE8 BEFORE OPERATING YOUR CHAIN SAW. Compare the Illustrationswith your unit to famllladze
yourselfwith the location of the vadous controlsand adjustments. Save thls
manual for future reference.
Bar Tool
Front Handle
Starter Rope
ON/STOP
Pdmer
Bulb
[RRFTSMRN"
Bar OII RII Cap
Housing
Fuel Mix Fill Cap
Cylinder Cover
Fast Idle I
Chain
Direction
of Travel
Adjusting
Screw
Throtlfe
Tdgger
Choke
Knob Barclamp
Bar Clamp Nuts Gu)ds Bar
Chain
Catcher
=l i
ON/STOP SWITCH
The ON/STOP Switch Is used to stop
the engine.
THROTTLE TRIGGER
-Jhe throttle trigger controls engine
speed.
THROTTLE LOCKOUT
The throttle lockout must be pressed
before you can squeeze the throttle tdgger.This feature prevents you from accidentallysqueezing the trigger.
FAST IDLE LOCK
The fast Idle lock holds the thmttie rigger in the starting position. Activate the
fast idle lock by pressing the throttle
lockoutand squeezing the throttle trigger, With the throttle rigger squeezed,
=press the fast idle lock. Release the
.,,
throttlelockoutand trigger while holding
the fast idle lock button.
CHOKE KNOB
The Choke Knob activates the choke to
provide additionalfuel to the engine
dudng cold starting.
PRIMER BULB
The Primer Bulbcirculates fuel to the
carburetorto provide quicker starting.
CHAIN TENSION
It Is normal for a new chain to stretch
dudng first 30 minutes of operation.You
should check your chain tension frequentiy.See Chain Tension under the
Service and Adjustments section.
6
BEFORE STARTING ENGINE
lines and carburetorare empty.Use fresh
fuel next season. See STORAGEinstrucWARNING: Be sure to read the fuel
tionsfor addltlonaJ
Inlom'_dion.
handling InformaUon In the safety rules Never use engine or carburetorcleaner
section of this manual before you begin.
products in the fuel tank or permanent
If you do not understand the fuel hendamage may occur.
dling informationdo not attempt to fuel
See the STORAGEsectionfor additional
your unit. Seek help fn2m someone that information.
does understand the in-formationor call
STOPPING YOUR ENGINE
the customer assistance help line at
• MoveOn/Stopswitchto S'I'OR
1.800-235-5878.
• If engine does not stop, pull choke
GUIDE BAR AND CHAIN OIL
knob out fully.
The chain oiler prov]dee continuous lubricatlonto the chain and guide bar. Be STARTING YOUR ENGINE
COLD ENGINE OR WARM ENGINE
sure to fill the bar oil tank when you fill
AFTER RUNNING OUT OF FUEL
the fuel tank (Capacity = 6.8 ft. oz.).
For maximum guide bar and chain life, • Fuel engine with 40:1 fuel mix.
• Fill bar oil tank with bar oil..
we recommend you use Craftsman
chain saw bar oil. If Craftsman bar oil Is • Prime engine by pressing pnmar bulb
six times.
not available, you may use a good
•
Move On/Stop switchto ON.
grade SAE 30 oil untll you are able to
PdmerBulb
obtainCraftsman brand. The oil output
is automatically metered duringoperation. Your saw will use approximately
SNtdl
one tank of bar odfor every tank of fuel
On/Stop___
mix. Always fill the bar oil tank when
you fill the fuel tank.
_'_b/"_'!
Choke Positions
FUELING ENGINE
This engine is certified to operate on
unleaded gasoline. Before operation,
gasoline must be mixed with a good
I
quality2-cycle alr-coolnd engine oil. We
• Actuate choke by pullingchoke knob
recommend Craftsman brand oil. Mix
fully out.
gasoline and oil at a ratio of 40:1 (A
•
Set saw on the ground. Grip front
40:1 ratio is obtained by mixing 3.2
handle with your left hand and place
ounces of oli with I gallon of unleaded
rightfoot through rear handle.
gasoline). DO NOTUSE automotive oil
or boat oil. These oils will cause engine
Starter Rope Handle
damage. When mixing fuel follow the
instructionsprinted on the container.
Once oll is added to the gasoline,
Left Hand
shake container momentarily to assure
on Front
that the-fuel is thoroughly mlxnd.
Handle
Always reed and follow the safety rules
reletlngto fuel before rOelidg your unit.
IMPORTANT
Experienceindicatesthat alcohd blended
FootThroughRearHandle
fuels(calledgasoholor uslngethanolor
• Set fast idle by depressing the throttle
methanol)canattractmoisturewhich
lockwith your right hand. Then,
squeeze and holdthrottle trigger. With
dour thumb, press the fast idle lock
.,da._
.
tba fuel _
of an engins
own and hold. Next, release the
while In storage.
thmtUe trigger.
To avoideeglne problems, tha fual system shouldbe emptiedbefore storagefor • DONOT squeeze throttle trigger duringstarting; otherwise, it willbe nec30da_ orlonger.
Drain the gas tank,
starttha engineand let it mn untgtha fuel
essary to reset the fast Idle lock.
leadstoseparation
and fomw_
7
NOTE:Whenpullingthe starterrope, OPERATING TIPS
• Check chain tension before first use
do not usethe full extentofthe rope.
Do notlet starter rope snap beck. Hold
and after J minute of operation. See
handle. Let rope rewind slowly.
• Pull starter rope handle firmlyand
quicklywith your dght hand untilthe
engine attempts to start, but no more
than 5 pulis. Then, push in choke
knobtothe Full Positiorr :Resume
pulling handle untilengine starts.
• Above 400F, allow engine to run for
approximately 5 seconds. P_h the
choke knob In to the OFFposition;
then squeeze and release throttle trigger to allow engineto idle.
• Below 40•F, allow engine to warm up
for 30 seconds to I minute with choke
ASt partialposition. P.ushchoke knob in
pproximatb_ 1/2 outthen squeeze and
release throttle trlgger to allow engine
to idle.
• To stop engine, move On/Stop switch
to the STOPposition.
STARTING A WARM ENGINE
DONOT use the choke to start a warm
engine or flooding and hard starting
may occur.
• Move On/Stop switch to ON.
• Set fast Idle lock.
Chain Tension in the Maintenance
section.
• Cut wood only. Do not cut metal, plastics, masonry, non-woodbuilding matadals, etc..
•, Stop the saw if the chain strikes a foralgn object. Inspectthe saw and repair parts as necessary.
• Keep the chain out of dirtand send.
Even a small amount of dirt will quickly dull a chain and Increase the possibilityof kickback.
• Practice cutting a few small logs using
the followingsteps. This will help you
get the "feel"of using your saw before
you begin a major sewing operation.
• Squeeze the throttle trigger and ak
low the engine to reach full speed
before cuffing.
• Begin cuttingwith the saw frame
againstthe log.
• Keep the engine at full speed the
entire time you are cutting.
• Allow the chain to cut for you. Exert
only lightdownward pressure.
• Release'the throttle rigger as soon
as the cut is completed, allowingthe
engine to idle. If you run the saw at
full throttlewithout a cutting load,
unnecessarywear can occur. .
• To avoid losingcontrol when cut is
complete, do not put pressure on
saw at end of cuL
• Stop enginebefore settingsaw down.
Be sure choke is in the OFF position.
" With saw on ground, gnp front handle
with left hand and place your rightfoot
through rear handle.
• Pull starter rope haqdle untilengine
starts.
• Squeeze and release throttletrigger
to return engine to idlespeed.
TREE FELLING TECHNIQUES
WARNING: Check for broken or dead
DIFFICULT STARTING OR
branches which can fall while cutting
STARTING A FLOODED ENGINE
The engine may be flooded if it has not causing sedous injury.Do not out near
buildingsor electdcel wires if you do not
started after 10 pulls. Rooded engines
know the directionof tree fall, nor cut at
can be cleared of excess fuel withthe
nightsince you will not be able to see
--.Jollowing procedure:
well, nor duringbad weather such as
Engage the fast Idle lock.
• Verify that the On/Stop switch is in the rain, snow, or strongwinds, etc.
ON position.
• Carefully plan your sawing operation
In advance
• Push choke knob to the OFF position.
• With saw on ground, gap front handle • Clear the work area You need a clear
area all around the tree so you can
with left hand and place rightfoot
have secure footing
through rear handle.
• Study the natural condftlonsthat can
• Pull starter rope handle until engine
starts.
cause the tree to fall in.a particular
direction.These conditions include:
• Starting could require many puPsdepending on how badly the unitis
• The
directionand
speed.
The wind
lean of
the tree. The
loan of a
flooded. If engine stillfails to start, retree might not be apparent due to
_fer to the TROUBLESHOOTINGchart or
call 1-800-235-5878.
uneven or slopingterrain. Use a
8
plumbor levelto determinethe directionof treelean.
• Weightand branches on one side.
This hingewill helppreventthetree
fromfallingin the wrongdirection.
'_._._
_\'_'%
• Surroundingtrees and obstacles.
• Look for decay and rot. If the trunk is
rotted, it can snap and fall toward the
• operator.
Make sure there is eneugh morn-for
person or other objects. Engine noise
can drown out a warning call.
• Remove dirt, stones, loose bark,
nails, staples, and wire from the tree
where cuts are to be made.
_>_
Plane clearretreatpath
- - -(*'_..,_lk.
Hingeholdstreeon
stumpand helps
.aL'__'_'_control
f
_._\_._,_,
Bib
_,_
_
fall
Openingot
fellingcut
NOTE: Before fellingcut is complete,
use weages to open me cut when
necessary to control the directionof fall.
To avoid kickbackand chain damage,
use wood or plestlowedges, but never
steel or iron Wedges.
• Be alert to s,gnsthat the tree is ready
Directionof Fall
to
crackingsounds,
widening
thefall:
felling
cut, or movement
in theof
upper branches.
V
_
• As
treeand
starts
fall, stop
sew,
it
down,
gettoaway
quickly
onput
your
planned retreat path.
FELLING LARGE TREES
• Be extremely cautious with partially
(6 inches in diameter or larger)
fallen trees that may be poorly supported. When a tree doesn't fall comThe notch method is used to fell large
pletely,set the saw aside and pull
trees. A notchis cut on the side of the
down the tr_e with a cable winch,
tree in the desired directionof fall. After
block and tackle, or tractor. Do not
a felling cut is made on the opposite
use your saw to cut down a partially
side of tree, the tree will tend to fall in
fallen tree.
the directionof the notch.
NOTE: If tree has large buttress roots, cu'n'ING A FALLEN TREE
remove them before making the notch. BBUCKING)
ucklng is the term used for cutting a
NOTCH CUT AND FELLING TREE
fallen
tree to the desired log size.
• Make notch cut by cuffing the top of
the notch timt. Cut through 1/3 of the
WARNING: Do not stand on the log
diameter of the tree. Next complete
being cuL Any portioncan rollcausing
the notch by cuffingthe bottom. See
lossof footing and control. Do not stand
illustration.Once the notch is cut, redownhillof the log being cut.
move the wedge of wood from tree.
IMPORTANT POINTS
t Rnal cuthere
• Cut only one log at a time.
Use a sawhorse to cut small logs.
tow.operator.
Never allow another person to hold
:. Cut shattered wood very carefully;
the logwhile cutting and never hold
the
logwith
leg or
foot.logs,
Do not
cut inyour
an area
where
limbs,and rootsare tangled. Drag logs
intoa dear area before cuttingthem.
• Alter removing the wood, make the
BUCKING
TECHNIQUES
felling out on the opposite side of the
notch.This is done by making a out
WARNING: If saw becomes pinched
about two inches higher than the cen- or hung in a log, don1 tryto force it out.
ter of the notch.This will leave
You can lose control ofthe saw result'ene_gh uncutwood between the fell- ing in injury and/or damage to the saw.
ing cut a_d the notch to form a hinge. Stop the saw, drive a wedge of plastic
Nctch....,=_
._._._:.:I ..."
First,cut
| r
{ /
_
I \ _"
Second_
J._._-,_
Hinge
Q
or woodintothe cut untilthe saw can be
Usinga log
easily. Restartsaw and carefully for _mppo_
reenter the cut. Do not usa a metal
wedgs.Donotattempt
torsmrt your
saw when it is pinchedor hung In a log.
Use s wedge to remove pinchedsaw
£.
Tum Saw OFF and use s pl8_o or
wooden wedge to force cut open.
Ovemuttlng begins on the top side of
the logwith the bottom of the saw
against the log. When overcuttinguse
lightdownward pressure.
Overcuffing
Undercutting
Undercutting Involves.cuttingon the
underside of the log with top of saw
-tgainstthe log. When undercuttinguse
Ight upward pressure. Hold saw firmly
;nd maintaincontrol. The saw willtend
o push back toward you.
u_
cut" -...
BUCKING USING A LOG OR
SUPPORT STAND
• Remember your first cut is always on
the compression.sideof the log. (Refer to the Illustration below for your
first and second cut).
• Your first cut should extend 1/3 of the
diameter of the log.
• Finishwith your second cut.
Using/_
ndcut
_1
_ Cut
WARNING: Never turn saw upside
|own to undercut. The saw cannot be
,'ontroiledin this position.
_.lways make your first cut on the
',ompresslonside of the log.
2nd Cut
First cut on compression side of log
Secondcut
Firstcuton compression sideof log
BUCKING WITHOUT A SUPPORT
, Overcut through 1/3 of the diameter of
the log.
• Roll the log over and finishwith a saoond ovemut.
, Watch for logs with a oompreslon
side. See illustrationabove for cutting
__._!ogs
with a compression side.
UMBING AND PRUNING
WARNING: Never climb Into a tree to
limb or prune. Do not stand on ladders,
platforms,a log, or in any position
which can cause you to lose your balance or control of the saw.
IMPORTANT POINTS
• Watch out for spflngpolss.
Spdngpoissare small size limbs
which can whip toward you, or pull
you off balance. Use extreme caution
when cuttingsmall size limbs.
• Be alert for spdngbeck. Watch out for
branches that are bent or under pressure. Avoid being struck by the
branch or the saw when the tension in
the wood fibers is released.
• Frequentlyclear branches out of the
way to avoid tdpping over them.
10
LIMBING
branchesare higherthanyourshoul• Limba tree onlyafterit is cutdown. def.Geta professionalto do thejob.
• Leavethe larger limbs undemsath the • Make your first cut 1/3 of the way
felled tree to supportthe tree as you
through the bottom of the limb.
work.
• Next make a second cut all the way
• Start at the base of the felled tree and
through the limb.
•
Finishthe pruningoperation by using
worktoward the top, cutting branches
and limbs. Remove _'nail limbs-with
an overcuLsothat the stump of the
one cut.
limb protrudes 1 to 2 Inches from the
trunkof the tree.
• Keep the tree between you and the
chain.
Secondcut
• Remove larger, supportingbranches
with the 1/3, 2/3 cutting techniques deecdbsd in the buckingsection.
• Always use an overcut to cut small.
and freely hanging limbs. Undercut
ting could cause limbstOfall and
pinch the saw.
PRUNING
WARNING: Limit pruningto limbs
shoulder heightor below. Do not cut if
0utl ,2in.
_nkofb'es
CUSTOMER RESPONSIBILITIES
Fill in dates as you complete
regular service
Check for damaged/worn parts
Before Ariel Ever_ Every Ysady
Use Use 5hra 25hrs
Check for loose fasteners/pads
Check chain tension
service
Dates
p,,
p,,
Check chain sharpness
Check guide bar
p_
Clean unit & labels
Clean air filter
y,
Clean/inspect spark arrestor
screen & Inspect muffler
p,,
v"
Replace spark plug
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover Items that have been subjected to
operator abuse or negligence. To recalve full value from the warranty, the
operator must maintain unit as instructed in this manual. Vadous adjustments
will need to be made pedodlcally to
properlymaintain your unit.
• Once a year, replace the spark plug,
air filter element, and ch_k guide bar
and chain for wear. A new spark plug
aml-eJrfilter element assures proper
air-fuel.mixture end helps your engine
run better and last longer.
WARNING: Disconnect the spark plug
beforeperforming
maintenanceexcept
for carburetoradjustments.
LUBRICATION
1 s_,;o
t
2 e,,o,
recap ",1
_"1!I
1 U__
2 Use Gm_sman chain saw bar oil
CHECK FOR DAMAGED OR
WORN PARTS
Adjusting
Screw- 1/4 Turn
Replacement of demaged/wom parts
should be referred to your Sears Setvice Center,
NOTE: It Is normal for a small amount
of oHto appear under the saw after eniginastops. Do not confuse this with a
eaklng oil tank. _
: ....
switch.funotionsproperly by.moving
the swdch to the "Stop" position.
Make sure engine stops; then rested
engine and continue.
.
Fuel TankDo not
use saw
it fuel
On/Stop
Switch
- Ensure
On/Stop
tank shows signs of damag.e or leaks.
Oil Tank - Do not use saw ,f oil tank
shows signs of damage or leaks.
FASTENERS AND PARTS
• Bar Clamp Nut
• Chain
• Muffler
• CylinderShield
• Air Filter
• Clutch DrundSprocket
• Handle Screws
• VibrationMounts
• Starter Housing
• Handguard
CHECK CHAIN TENSION
• Use the screwdriver end of the bar
toolto move chain around guide bar
to ensure kinks do not exist. The
chain should rotate freely.
_
-'l_rClamp Nuts
Bar'rool
• Loosen bar clamp nuts untilthey are
finger tight against the bar clamp.
• Turn adjusting screw clockwise until
chain barely touches the bottom of
guide bar.
'_
Adjusting /
turn adjusting screw 1/4 turn clock-
wise. Repeat.untilsag does not exist.
• While liftingtip of.guide bar, tighten
Torque to 10-15 ft-lbs.
./'_J
Bar
,Y_
Clamp
|_.
Nuts
bar clamp nutswith thetool__
bar
• Use the screwdriverend of the bar
tool to move chain around guide bar.
• If chain does not rotate, it is too tight.
Slightlyloosen bar clamp nutsand
turn adjustingscrew 1/4 tum counterclookwisa.Retightenbar clamp nuts.
• If chain is too loose, it will sag below
the guide bar. DO NOT operate the
saw if the chain is loose.
CHECK CHAIN SHARPNESS
A sharp chain makes woodchips. A
dull chain makes a sawdustpowder
and cuts slowly.
CHECK FOR LOOSE
___m____m
• Lift up tip of guide berto check for
sag, Release tip of gulde bar, then
/
CHAIN SHARPENING
Chain sharpening requiresspecial
tools. You can purchase sharpening
tools at Sears or go to a professional
chain sharpener.
Conditionswhich require guide bar
maintenance:
• Saw cuts to one side or at an angle
• Sew has to be forced through the cut.
CHECK
GUIDE
BAR
• inadequate
supply
of oil to bar/chain.
Check the condition of guide bar each
time chain Is sharpened. A wom guide
bar will damage the chain and make
cuttingdifficult.To maintain guide bar:.
• Move On/Stop switchto "Stop."
• Remove bar and chain from saw.
• Clean ell sawdust and any other
debds from the guide bar groove and
Remove
sprocket
Sawdust
hotsafter
From
each lJ
use. _.,,
V" sp=k.t.ol.
GuideBarQroot__
• Using bar tool, loft chain aroundguide
., .__...barto ensure all linksare in bar groove.
12
• Addlubricanttosprocketholeafter
eachuse.
• Burringof guide bar rails is a normal
process of rail wear. Remove these
burrs with a flat file.
• When rail top is uneven, use a flat file
to restore square edges and sldss.
TU T
sidesSquare
Rio
Edgesand
INSPECT MUFFLER AND SPARK
ARRESTOR SCREEN
As the unit is used, carbon deposits
build up on the muffler and spark
arrestor screen, and must be removed
to avoid creating a fire hazard or affecting engine performance.
Replace the spark arrestor screen if
breaks occur.
_._
WornGroove
CorrectGroove
Replace guide bar when the groove is
wom, the guide bar is bent or cracked,
orwhen excess heating or bur._g of
the ragsoccurs. If replacement zsnsoessmy, use only the guide bar spedffed
for your saw in the repair parts hstor on
the decal located on the chain saw.
CLEAN UNIT & LABELS
• Clean the unit using a damp cloth with
a mild detergenL
• Wipe off unitwith e clean dry cloth.
CLEAN AIR FILTER
A dirtyair filter decreases the life and
performance of the engine and increases fuel consumptionand harmful
emissions. Always clean your air filter
after 15 tanks of fuel or 5 hours of op
eration, whichever comes firsL Clean
more fro_.uentlyin dusty conditions.A
used air biter can never be completely
cleaned. It is advisable to replace your
air filter with a new one after every 50
hours of operation, or annually, whichever comes firsL To clean filter:.
• Loosen 3 screws on cylinder cover,
Removecylindercover,
Removeairfilter.
• Clean the air filter using hot soapy
water. Rinse with clean cool water.
Air dry completely before reinstalling.
• Lightlyoil air filter before installingto
improve the efficiency of air filter. Use
2-cycle engine oil or-motor oil (SAE
30). Squeeze excess oil from filter.
• Reinstall air filter.
• Reinstall cylinder cover and 3 screws
(15-20 [n-lbs.).
CylinderCover
AirRlter
Screws
Muffler Diffuser
s_
Arrestor
Muffler
Cover
Screws
Muffler
Body
MufflerCover
CLEANING THE SPARK
ARRESTOR SCREEN
Cleaning is r.equired every 25 hours of
operation or annually, whichever comes
first.
• Loosen and remove the 2 muffler cover screws.
• Remove the muffler cover (cover
snaps off muffler body).
• Remove muffler diffuserand spark
arrestorscreen assembly. Notice the
orientationof these parts for reassem-
• bling.
Cleanthesparkarrestorscreenwitha
wire brush. Replace screen if breaks
are found.
• Replace any broken or cracked muffler parts.
• Reinstalldiffuser and spark arrestor
screen assembly with round holes
facing up.
• Reinstall muffler cover and 2 screws
(7-e ft-_).
REPLACE SPARK PLUG
The spark plug should be replaced
each year to ensure the engine starts
easier and runs better. Ignitiontiming is
fixed and nonadjustable.
• Loosen 3 screws on cylindercover.
• Remove the cylinder cover.
Pull off the spark plug beoL
Remove spark plug from cylinder and
• Replacewith Champion RCJTY spark
C_indar
Cover
plug and tlghten.lv_hth
a 3/4 Inch socket
wrench (10-12 ft Ibe). Spark pluggap
should be .025 in.
; Reinstall the spark plug boot.
Reinstall the cylinder cover and 3
screws (15-20 in-lbs).
Plug
CHAIN REPLACEMENT
Cutters
Dep_ Gauge
CAUTION: Wear protective gh_vas
when handling chain. The chain is
sharp and can cut you even when it is
not moving.
it is normalfor a new chainto strstchdurIngthe first 15 minutesof opera_n. You
should recheck your chaintensionfrequantlyand adjust the chaintensionas
required.SeeChain Tensionsection.
• Move On/Stop switch to the Stop
position.
• Replace the old chain when it becomes worn or damaged.
• Use only the Low-Kickback replacement chain specified in the repair
parts list. The correct replacement bar
and chain is also specified on a decal
located on the chain saw.
• See your Sears Sewice Center to replace and sharpen individualcutters
on your chain.
• Remove bar clamp nuts.
• Remove bar clamp.
• Remove the old chain.
Drive Links
• Place chain over and behind clutch.
• Fit bottom of ddve links between teeth
in sprocket nose.
• Fit chain drive links intobar groove.
• Pull guide bar forward untilchain is
snug in guide bar groove..
• Now, install bar clamp making sure
the adjustin_ pin Is pos,tlonedin the
lower hole in the guide bar.
/
!
_r
Adjusting
Pin
Hole
Guide Bar
• Install bar clamp nuts and finger tighten only. Do not tighten any further at
this polnL
Bar
Clamp
Bar
Clamp Nuts
• Turn adjusting sorew by hand courP
terdockwise untiladjusting pinjust
touches the stop.
• Slide guide bar behind clutch drum
untilguide bar stops against clutch
drum sprocket.
• Carefully remove new chain from
package.
Hold chain with the drive
--=links as shown.
Bar Clamp Nuts
CHAIN ADJUSTMENT
See "ChainTension"in Maintenance
section.
14
CLEAN FUEL FILTER
Tocleanfuelfilter,drainyourunitby
runningdry offuel, removefuelcap/retainerassemblyfromtank.Pulltilter
fromtankandremovefromllne.Clean
withmilddetergentand rinse. Dry thoroughly,reassemble. _
_.....
CARBURETOR ADJUSTMENT
WARNING: The chain will be moving
dudng most.ofthle procedure. Wear
your prated.ire equipment and observe
all safety precautions. During the low
speed mixture adjustment recheck idle
speed after each tum of the screw, The
chain must not move at Idle speed,
Carburetor adjustment is odtical and if
done impmpedy can permanently damage the engine as well as the carburetor. If you require further assistance or
are unsure about performing this procedure, call our customer assistance help
line at 1-800-235-5878.
Start motor,let it runfor 3 minutes, and
proceed to.the adjustment section. If
engine does not start, refer to troubleshootingchart or call 1-800-235-5878.
if engine performance is acceptable at
the pmsst positionsand them is no
chain movement at idle, no further adjustrnant is necessary.
ADJUSTING PROCEDURE
Idle Speed-T
Allow engine to idle. Adjustspeed until
engine runs withoutchain movement or
stalling.
• Turn clockwise to incmasa engine
speed if engine stalls or dies.
• Tum counterclockwiseto decrease
speed.
No further adjustments am necessary if
chain does not move at idle speed and
if performance is satisfactory.
Low Speed Mixture-L
Allow engine to idle.Then accelerate
Old fue!, a dirty air filter, dirty fuel filter, the engine and note performance. If engine hesitates, bogs down, orsmokes
or floodingmay give the impressionof
dudng acceleration,turn mixturescrew
an improperlyadjusted carburetor.
clockwisein 1/16-tumincrements until
Check these conditionsbefore adjustperformanca.i_satisfactory.Repeat this
ingthe carburetor.
The carburetor has been carefully set at l)urocedureas neimssaryfor proper adstmenL After completingadjustments,
the factory.Adjustments may be necescheck for acceleration and chain movecary if you not[caany of the following
ment at idle. Reset if necessary.
conditions:
• Chain moves at Idle. See "Idle Speed" High Speed Mlxture.-H
DO NOT operate engine at full throttle
underadjustingprocedure.
• Sawwillnotidle.See "IdleSpeed"
for prolonged pedods while making adand "LowSpeedMixture'underadjustments. Damage to the engine can
occur.Make a test cuL Basedon perlusting procadum,
formance of the saw while cutUng,ad• Engine dies or hesitates when it
should accalerate. See "Acceleration just the high speed mixture setting in
I/I 6-turn incrementsas follows:
Check" under adjusting procedure.
• Qockwisa unl]1saw has goodpower in
• Loss of cuttingpower. See "High
Speed Mixture H" under adjusting
the cutwith no hesitallon.Do not adjust
procedure.
by scund or spesd, butjudge by how
wellthe saw peflorms.,
In the cut.
There are three adjus_tmantscrews on
• Counterclockwiseif the saw has
the carburetor. They are labeled H, L,
speed, but dies In the cut or lacks
and T. They are located in the area just
power in the cut.
above the pdmer bulb.
After
completingadjustments, check for
CARBURETOR
PRESETS
acceleration and chain movement at
When making adjustments, do not force idle. Reset if necessary.
the plastic Umiter caps beyond the
Acceleration Check
stops or damage will occur.
If the enginedies or hesitatesinsteadof
if carburetor presets am not needed,
ec_lerstlng,tumthelowspeedmixt.m
proceed to "Idle Speed-T."
a_ustmant counterdockwiseuntilyou
• "rum both mixture screws counterhave smoothacceismtlonwith no chain
clockwiseuntilthey stop'.
movementat idle. Recheckand adjustas
,. Tu_rpthe idle speed screw clockwise
u-_il it stops. Now turn counterclock- necessaryfor acceptableperformance.
wise 4-,1/2fullturns.
Prepareyourunitforstorageat theend
of the seasonor if it will not be usedfor
30 daysor more.
WARNING:
•
•
I •
tive in minimizing the formation of fuel
.g.umdeposits du.dng.storage. Add stabihzer to the gasolzne ,n the fuel tank or
fuel storage container. Follow the mix
instructions found on stabilizer containera. Run engine at least 5 minutes after
unit
stodng
or transporting.
i the
Allow
thebefore
engine
to cool,
and secure
adding stabilizer.
Store chain saw and fual in a well
ventilatedarea where fuelvapors
cannotreachsparksoropenflames
fromwaterheaters,electricmotorsor
switches,fumaces,etc.
• Store chain saw with all guards in
place and position chain saw so that
any sharp object cannot accidentally
cause injury.
• Store chain saw well out of the reach
of children.
CRAFTSMAN
40:1, 2-cycle engine oil
(aircooled)is espedallyblendedwith
fuelstabilizer.If youdo notusethis
Sears oil, youcanadd a fuelstabilizer
to your fuel tank.
ENGINE
• Remove spark plug and pour 1 teaspoon of 40.1, 2-cycle engine oil (air
cooled) throughthe spark plug opening. Slowly pull the starter rope 8 to
10 times to distributeo11.
EXTERNAL SURFACES
• Replace spark plugwith new one of
If your chain saw is to be stored for a
recommended type and heat range.
period of time, clean it thoroughlybe• Clean air filter•
fore storage. Store In a clean dry area.
• Check entire unitfor loose screws,
• Lightly oll external metal surfaces and
nuts, and bolts. Replace any damguide bar.
aged, broke0, or wom pads.
• Oil the chain and wrap it in heavy pa- • At the beginningof the next season,
per or cloth.
use only freshfuel having the proper
gasoline to oil ratio•
FUEL SYSTEM
OTHER
Under Fueling Engine in the Operating
Section of this manual, see message
• Do not store gasoline from one season to another.
labeled IMPORTANT regarding the use
• Replace your gasoline cenif it starts
of gasohol in your chain saw.
to rust.
Fuel stabilizer is an acceptable altema-
16
TROUBLE SHOOTING CHART
TROUBLE
CAUSE
Enginewillnot
startor will run
Engine flooded.
onlya few
Ignitionswitch
Fael
tank empty.
off.
secondsafter
Spark plug not fidng.
starting.
• Fuel not reaching
REMEDY
•
•
•
•
•
Move Ignitionswitch to ON.
See "Starting Instructions."
Ril tank with correct fuel mixture.
Install new spark plug.
Check for dirty fuel filter;,replace.
Check for kinked or splitfuel line;
repair or replace.
• See "Carburetor Adjustments."
carburetor.
Enginewill not
idlepmpedy.
• Carburetor r quires
adjustmanL
• None of the above.
• ContactSearsService.
• Idle speed set too high • See "Carburetor
Adjustments."
or too low,
• Low Speed Mixture
• See "Carburetor Adjustments."
requires adjustment.
• Crankshaftsealswom. • Contact Sears Service.
• Contact Sears Service.
.. Compression
low.
Noneof the above.
• Contact Sears Service.
Enginewill not : Air filter dirty.
accelerate,
Spark plugfouled.
lackspower,
or diesunder • Carburetor requires
a load.
adjustment.
• Clean or r place air filter.
• Clean or replace plug
and regal).
• See "CarburetorAdjustments."
• Exhaust ports or muffler outlets plugged.
• Compression low.
• None of the above.
Engine smokes : Choke partiallyon.
excessively.
Fuel mixture Incorrect.
• Air filter dirty,
• High Speed Mixture
requires adjustment.
• Crankcase leak.
Engine runs
hoL
Oil inadequate
for bar and
chain
lubdoafion.
• Contact Sears Service.
./
• Contact Sears Service.
• Contact Sears Service.
• Adjust choke.
• Empty fuel tank and refillwith
correct fuel mixture.
• Clean or replace air filter.
• See "CarburetorAdjustments."
• Contact Sears Service.
• Fuel mixture incorrect.
• Spark plug Incorrect.
• High Speed Mixture
set too lean.
• Exhaust portsor muftier outlets plugged.
• Carbon build-up on
muffler outletscreen.
• Fan housing/cylinder
fins dirty.
• None of the above.
• See "FuelingYour Unit."
Replace with correct plug.
• See'Carburetor Adjustments."
• Contact Sears Service
• Clean spark arrestor screen.
• Clean area.
• Contact Sears Service.
• Ril oil tank.
• Contact Sears Service.
• Oil tank empty.
• Oil pump or oil filter
d oggGed.
• Gui_d_e
bar oil hole
blockpd.
• Remove bar and clean.
q"t
TROUBLE
SHOOTING
CHART-
Continued
TROUBLE
CAUSE
REMEOY
Chain moves
at Idle speed,
* idle speed requires
adjustmanL
J"Clutch requires repair.
• See "CarburotorAdjustments."
B
• Contact Sears Service.
Chain does
• Chain tension too
• _ght: .....
- " "
Jnot move
_when engine ;, Carburetor requires
is accelerated.
adjustment.
• Guide bar roils
pinched.
• Clutchslipping.
• See "ChainTension."
• See "CarburetorAdjustments."
• Repair or replace.
• Contact Sears Service.
Chain clatters • Chain tension incorrect.
or cuts roughly • Cutters damaged.
• Chain worn.
°'Cutters dull, improperly
sharpened, or depth
gauges too high.
Chain cuts at
an angle,
See "Chain Tension."
Contact Sears Service.
Rssharpen or replace chain.
See "Sharpening Chain."
• Contact Sears Service.
• Installchain in dght direction.
• Sprocket
worn.
Chain installed
backwards.
Chain stops
within the cut.
•
•
•
•
• Chain cutter tops not
filed flat.
• Guide bar burred or
bent; rails uneven.
• Clutch slipping
• See "Sharpening Chain."
• Cutters damaged on
one side.
• Chain dull on one side.
• Guide bar bent or wom.
• See "Sharpening Chain."
• Repair or replace guide bar.
/
• Contact Sears Service.
• See "SharpeningChain."
• Replace guide bar.
If situations occur which are not covered in this manual, use care and good
Judgement. If you need assistance, contact Sears Service or the CUSTOMER
ASSISTANCE HELPLINE at 1-800-235-5878.
U. S. EPA/CAMFORNIA
EMISSION CONTROL
maintenance of your lawn and garden
equipment engine.
Your emission control system includes
WARRANTY STATEMENT
partssuchasthecarburetor
andtheignitionsystem.
Where a warrantable condition exits,
SEARS will ropairyour lawn and garden
equipment engine at no cost to you. Expenses covered under warranty include
The U. S. Environmental Protection diagnosis, part.sandlabor.
Agency/Cailfomia Air Resources Board
and SEARS, ROEBUCK AND CO., USA MANUFACTURER'S
WARRANTY
are pleased to explain the emissions COVERAGE-control system warranty on your lawn If.any emissionsrelated Pad on your anand garden equ,pment engine. All new gme (as listed under Emissions Control
utility and lawn and garden equipment Warranty Parts List) Is defective or a deeng,nes must be designed, built, and fect in the materials or workmanship of
equipped to meet the stringent anti- the en_ine causes the failure of such an
smog standards. SEARS must warrant emission mlatsd part, the part will be retheemisaioncontmlsyetemonyourlawn
paired or replaced by SEARS.
•
and garden equipment engine forthe pe- OWNER'SWARRANTY
RESPONdods of time listed below provided there SIBILITIES - ' -hasbeen no abuse, neglect, or improper As the lawn and garden equipment en18
Y_OUR WARRANTY RIGHTS
OBLIGATIONS
AND
gine owner,you are responsiblefor the shailbewarrant.ed.for thepedod
performance of the required mainte- of time up to the first scheduled replacenonce listed in your Owner's Manual. ment paint for that pair.
SEARS recommends that you retain all DIAGNOSIS - receipts covedng maintenance on your
lawn end garden equipment engine, but The owner shall not be charged for diagSEARS cannot deny warranty solelyfor nostic labor which leads to the deterthe lack of receipts or4oryour failure to minalion that a warranted part
ensure the performance of'all scheduled is
defective
diagnosticwork
is pep
formed
at anifthe
approved
SEARS servicing
maintenance.
As the lawn and garden equipment en* canter.
gine owner, you should be aware that CONSEQUENTIAL
DAMAGES - _;EARS may deny you warranty coveP SEARS maybe liablefor damages to orbage.if your lawn and garden equiL_nent erenginecomponentscausedbythefailengine or a part of R-has failed_due to ure of
awarranted part stillunderwarsl:_se, neglect, Improper maintenance,, renty.
unapproved modlflcauons, or me use ot
parts notmadeorapproved
bytheodgl- WHAT IS NOT COVERED -naJequipment m..an.,
ura_urer.
All failures caused by abuse, neglect, or
You are responsible for presenting your improper maintenance am not covereo.
lawn and garden equipment engine to a ADD-ON OR MODIFIED PARTS -SEARS authonzedrep_r canter as so.on The use of add-on or modifiedpads
as
a problem
exists, warranty
rapture
should
be completed
in a reasonable
amount of time, not te exceed 30 days.
If you have eny questions reclardlngyour
warranty'dghts and rospon_bilitiss,.you
should contact your nearest aumonzeo
service center or call SEARS at
1-800--473-7247.
WARRANTY
COMMENCEMENT
DATE - The warranty pedod bs_linson the date
tbe lawnend garden equipment engine Is
purchased.
LENGTH OF COVERAGE-This warranty shall be for a pedod of two
years from the initial date ol pumhsse.
WHAT IS COVERED - -
be
grounds_or disaJlowinga warranty
claim.SEAR
is not liableto cover failures of warranted
p_tscaused by the use ofadd-on or modifleo pans.
HOW TOFILEACLAIM-If you have any questionsreqar.dingyour
warranty dghts and responszo,ities,you
should contact your nearest authorized
service center or call SEARS at
1-800-473-7247.
WHERE
TO GET
WARRANTY
SERVICE --
Warranty
services
orrep_m_l
_.pr?-
vided at all SEARS at 1-8oo.-473-rz,_/
servicecenters,
MAINTENANCE,
REPLACEMENT
REPAIR OR REPLACEMENT
AND REPAIR OF EMISSION REOF PARTS -LATED PARTS -Repair or rep_osment of an_/warranted Any SEARS ap.provedreplacement part
part will be penormed at no charge to me used in the peifo_
of any w.arren_
ow_el_ai an approved SEARS servicing maintenance or repmr on emission re
center.
lated pads will be .p.rovldecl..without
Ifyouhave anyquestlons rega[dlngyour
charge to the owner I! me pan m unoer
warranty dghts and respons-lbil,tles,you warranty.
should contact your nearest autho_dzed EMISSION
CONTROL
WARRANservice center or call SEAR:5 at
1-800-473-7247.
TY PARTS LIST -i
1. Carburetor
WARRANTY PERIOD -2. IgnitionSystem
Any wan'anted part which is not I__,ed.
& Spaik Plug, covered .upto
uledfor replacement as requsreormunwmaintenance echeoule.
nance, orwhichis scheduled only for regb, _itY_)n Meduis
ular inspectionto the effect of "_'e_lr or MAINTENANCE
STATEMENT -replace as necessary" shall be warThe owne.r is resPOnsible for the perforrantedfor 2 years. Any
W;irrd_tedpart which is scheduled for re- mance ol all required maintenance as
placement as required maintenance defined in the owner's manual.
to
•
I
i
REPAIR PARTS
5O
51
6
7
2O
_Otl
OilPumpKit
Oral aO,$1 &4S)
2.
3.
4.
530_6119
S300_/I_I
530053711
O,1_ Vllve
Wlm- 11vottle
ClutohCover
_OOlOe4_
Screw
28. _160oo
SCIIW
84111Block
530018917
_nmt-cho_
_
Knob:_
e, s300mm
9. 6300041M aut_ St_n_ "
10. 530047061 Gl_chDn_nASs'y-
.. m_o+ms++,W_'
- Clut_
12. 530014949
Sw_h Liner
14. 53001814g
15. 6300_8284 _.g-_rmze Vent
llJ. 530015922 _ut
17. Ik.q00gt_S0 _adn _tcher
18. 53_015814 _emw
19. j S,._01Stl07 _wer -lhn:t
=0. 6,1001r_S _--I_
AdJum_
g2. 5_10_9811 _r _u_t_ng _ew
K_
23 U
e_r Moun_z Plsze
mow-m P_
lk_4g4_
_._oae3n
OnPl_
l:lug., o_ met
sctlw
FuelI.IneI_t
(Lmme
Dill+)
3_
53_047192 F,el CapA=l'y.
wn_ltmllm.
40, I_100181_ Bolt-Bar
41. 530047_
at-Pu_ A.'y.
_S_, _, 3_&_ )
_1
44.
46.
46:
47.
48.
530011_tO
6300161_12
530015814 8_ow
wo,. eur s_
1_001_1
S300_T/gI)
6,._00_8_4
D,_ Seel
FrontFI_
Hm_uard
20
Ref
Part No.
49.
60.
51.
52.
53.
54.
55.
56.
IF/'.
58.
59.
60.
$1.
53001Sg40 ,_few
6,.._0_748S S_t_ Handle
Rope
_3001_)2 S_lw
F_ Hous_
$300_'/531
6300_/817 SlanerPuney
m,=crl_on
530016127
$3001Sg20
530016134
71-31_9
71-_
kr.-ltP
NOtShOWn
.r_Te21
63oo_81g
Op_ret_Manual
Deca_FanHous_
REPAIR PARTS
10
14
11
12 13
17 lS
3
4
5
6
16
39
30
4O
19 20
.1
34
25
24
36
41
37
I
1_26
3G
Part No,
I.
3.
4.
5.
7.
16.
iL._0018610
I_.q0040700
530O16187
53001610_
53006,310,t,
l1300_OalO
6300_8317
83004G_.44
530047213
5,3OO69010
17.
16.
sO.
2O.
21.
_._0016090
71,-,0,,._49
63001g_,.40
5300_P0_1
530O60604
10,
11.
13.
14.
15.
Description
Ref.
530031163
,_S000779_
530016101
53OO9?6O4
530060"/0_
Pan No.
Ouc_rlpUon
En0k_Guket _
W_reHameu As_'y.
HeatInsulator
Muter Gaskut
_
B_ Plate
M.mer_ss_.
MufflerDiffuser
SparkArresto_
S_een
Screw
ChainB_ke Ir..d
sea_C_ _
22.
S30_
23.
- 53001560"/
24.--=
s3oo47oe2
21
30
I
REPAIR PARTS
_rb_or
4
Am_A_
t_ t_M_e
IPS,.qOO41g_
3
Krl
KIT*
KIT
Ref.
I.
23.
4.
5.
6.
7.
8.
22
23
For the repair or replacement parts you need
delivered directly to your home
Call 7 am - 7 pm, 7 days a week
1-800-366-PART
.-
.(1-800-366-7278)
Para ordenar piezaa con entrega a
domiclllo - 1-800-659-7084
For in-house major brand repair service
Call 24 hoursa day, 7 days a week
1-800-4-REPAIR
(1-800-473-7247)
Para pedir servicio de reparacidn a
domicilio - 1-800-676-5811
For the location of a Sears Parts and
Repair Center in your area
Call 24 hours a day, 7 days a week
1-800-488-1222
For information on purchasing a Sears
Maintenance Agreement or to inquire
about an existing Agreement
Call 9 am - 5 pm, Mohday-Saturday
1-800-827-6655
When requesting service or ord.ering
pads, always provide the follow,ng
information:
. Product Type
•
Part Number
SEARS
, Model Number • Part Description
/_wicabRepae
Specia_zs