Download Shark BR-304037 Operating instructions
Transcript
MODEL: BR OPERATING INSTRUCTION AND PARTS MANUAL ■ BR-442537 ■ BR-404027 ■ BR-353237 ■ BR-455037E ■ BR-373537 ■ BR-343087E For technical assistance or the SHARK dealer nearest you, call 1-800-771-1881 or visit our website at www.shark-pw.com 97-723 CONTENTS Important Safety Information ................................................................4-5 Component Identification Small ............................................................... 6 Component Identification Large............................................................... 7 Assembly Instructions.............................................................................. 8 Operating Instructions ........................................................................9-10 Applying Detergent and General Operating Techniques........................ 11 Shut Down and Clean-Up ...................................................................... 12 Storage .................................................................................................. 12 Troubleshooting ................................................................................13-14 Preventative Maintenance ..................................................................... 15 Oil Change Record ................................................................................ 15 Exploded View - Large........................................................................... 16 Exploded View Parts List ..................................................................17-19 Exploded View - Small ........................................................................... 20 Exploded View Parts List ..................................................................21-22 Hose and Spray Gun Assembly............................................................. 23 Specifications....................................................................................24-25 Warranty Model Number _________________________________ Serial Number _________________________________ Date of Purchase _______________________________ The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference. 3 96-718, 97-721, 97-723 • REV. 8/05a PRESSURE WASHER OPERATOR’S MANUAL INTRODUCTION & IMPORTANT SAFETY INFORMATION Thank you for purchasing a this pressure washer. All information in this manual is based on the latest product information available at the time of printing. Manufacturer reserves the right to make changes at any time without incurring any obligation. Owner/User Responsibility: The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this pressure washer. Warning information should be emphasized and understood. If the operator is not fluent in English, the manufacturer’s instructions and warnings shall be read to and discussed with the operator in the operator’s native language by the purchaser/owner, making sure that the operator comprehends its contents. CAUTION: Risk of asphyxiation — Use this product only in a well ventilated area. 4. Avoid installing machines in small areas or near exhaust fans. Exhaust contains poiRISK OF sonous carbon monoxide gas; ASPHYXIATION. USE ONLY IN A WELL exposure may cause loss of VENTILATED AREA. consciousness and may lead to death. It also contains chemicals known, in cer tain quantities, to cause cancer, birth defects or other reproductive harm. CAUTION WARNING Owner and/or user must study and maintain for future reference the manufacturers’ instructions. The operator must know how to stop the machine quickly and understand the operation of all controls. Never per mit anyone to operate the engine without proper instructions. This manual should be considered a permanent part of the machine and should remain with it if machine is resold. When ordering parts, please specify model and serial number. IMPORTANT SAFETY INFORMATION CAUTION CAUTION: To reduce the risk of injury, read operating instructions carefully before using. 1. Read the own er's man u al thoroughly. Failure to follow instructions could cause malREAD OPERATOR’S function of machine and result MANUAL THOROUGHLY PRIOR TO USE. in death, serious bodily injury and/or proper ty damage. 2.All installations must comply with local codes. Contact your electrician, plumber, utility company or the selling distributor for specific details. 3. This machine has been provided with Warning and Instruction decals for the safety of the operator. If these decals are removed or become damaged they should be replaced. Contact your dealer for replacement decals. RISK OF FIRE. DO NOT ADD FUEL WHEN OPERATING MACHINE. WARNING: Flammable liquids can create fumes which can ignite causing property damage or severe injury. WARNING: Risk of fire — Do not add fuel when the prod uct is operating. WARNING: Risk of explosion — Do not spray flammable liquids. 5. Do not place machine near flammable objects as the engine is hot. 6. Allow engine to cool for 2 minutes before refueling. If any fuel is spilled, make sure the area is dry before testing the spark plug or starting the engine. (Fire and/or explosion may occur if this is not done.) When refueling gasoline engines on mobile or por table equipment, make sure to refuel: a. outdoors; b. with the engine on the equipment stopped; c. with no source of ignition within 10 feet of the dispensing point; and d. with an allowance made for expansion of the fuel should the equipment be exposed to a higher ambient temperature. In an overfilling or spillage situation, additional precautions are necessary to ensure that the situation is handled in a safe manner. WARNING HIGH PRESSURE SPRAY CAN PIERCE SKIN AND TISSUES. 4 96-718, 97-721, 97-723 • REV. 8/05a WARNING: High pressure stream of water that this equipment can produce can pierce skin and its underlying tissues, leading to se ri ous in ju ry and pos si ble amputation. WARNING PROTECTIVE EYEWEAR AND CLOTHING MUST BE WORN. WARNING: High pressure spray can cause paint chips or other particles to become airborne and fly at high speeds. To avoid personal injury, eye safety devices must be worn. 7. Protective clothing and foot protection must be worn when using this equipment. WARNING KEEP WATER SPRAY AWAY FROM ELECTRICAL WIRING. WARNING: Keep water spray away from electrical wiring or fatal electric shock may result. 18. Never run pump dry or leave spray gun closed longer than 5 minutes. OPERATOR’S MANUAL 8. High pressure developed by these machines will cause personal injury or equipment damage. Use caution when operating. Do not direct discharge stream at people, or severe injury or death will result. 9. Never make adjustments on machine while in operation. 10. Do not block or tie spray gun in open position. 11. Do not place hands or feet on non-insulated areas of the pressure washer when starting gasoline engine. 12. When applying detergents, follow the safety rules on the detergent label. 13. Use detergent from a covered D.O.T. approved container. 14. Cleaning area should be provided with adequate slopes and drainage. This will reduce the possibility of a fall due to slippery surface. 15. The best insurance against an accident is precaution and knowledge of the machine. 16. Manufacturer will not be liable for any changes made to our standard machines, or any components not purchased from the manufacturer. 17. Read engine safety instructions provided. PRESSURE WASHER INTRODUCTION & IMPORTANT SAFETY INFORMATION 19. Do not allow children to operate the pressure washer at any time. 20. Do not allow machine to run unattended. 21. Inlet water supply must be cold and clean fresh water. CAUTION: Spray gun kicks back – Hold with both hands. CAU TION: Risk of injury – Dis con nect battery ground terminal before servicing. 5 96-718, 97-721, 97-723 • REV. 8/05a Nozzle Wand Spray Gun OPERATOR’S MANUAL PRESSURE WASHER COMPONENT IDENTIFICATION — SMALL MODELS Starter Grip Pump High Pressure Discharge Water Inlet High Pressure Hose Pump — Develops high pressure. Wand — Must be connected to the spray gun. Starter Grip— Used for starting the engine manually. High Pressure Hose — Connect one end to water pump discharge nipple and the other end to spray gun. Spray Gun — Controls the application of water and detergent onto cleaning surface with trigger device. Includes safety latch. Detergent Injector — Allows you to siphon and mix detergents (not shown). Note: If trigger on spray gun is released for more than 2 minutes, water will leak from valve. Warm water will discharge from pump protector onto floor. This system prevents internal pump damage. 6 96-718, 97-721, 97-723 • REV. 8/05a Nozzle Wand OPERATOR’S MANUAL Spray Gun PRESSURE WASHER COMPONENT IDENTIFICATION — LARGE MODELS Starter Grip Pump Water Inlet High Pressure Discharge High Pressure Hose 7 96-718, 97-721, 97-723 • REV. 8/05a PRESSURE WASHER OPERATOR’S MANUAL ASSEMBLY INSTRUCTIONS Spray Gun Pressure Nozzle Pressure Nozzle Wand Coupler Safety Latch High Pressure Hose Wand Coupler Wand Collar STEP 1: Attach the high pressure hose to the spray gun using teflon tape on hose threads. STEP 2: Pull the spring-loaded collar of the wand coupler back to insert your choice of pressure nozzle. STEP 3: Release the coupler collar and push the nozzle until the collar clicks. Pull the nozzle to make sure it is seated properly. Cold Water Source Dipstick Discharge Nipple Coupler Collar High Pressure Hose STEP 4: Remove shipping cap and install oil dipstick. Check pump oil level by using dipstick or observe oil level in oil window (if equipped). Use 30 wt. non detergent oil. STEP 5: Connect the high pressure hose to the pump discharge nipple. Push coupler collar forward until secure. Garden Hose Pump Water Inlet 8 STEP 7: Check inlet filters, remove debris, then connect garden hose to pump water inlet. CAUTION: Do not run the pump without water or pump damage will result. 96-718, 97-721, 97-723 • REV. 8/05a Garden Hose STEP 6: Connect garden hose to the cold water source. PRESSURE WASHER OPERATING INSTRUCTIONS Engine Oil Dipstick Gas Tank STEP 2: Fill gas tank with unleaded gasoline. Do not use leaded gasoline. OPERATOR’S MANUAL STEP 1: Check engine oil level. Oil level should be level with the bottom of the oil filler neck. Be sure the machine is level when checking the oil level. (Refer to the engine's operating manual included with machine.) We recommend that the oil be changed after the first 5 hours of use, then once every 50 hours. Note: Improper oil levels will cause low oil sensor to shut off engine. IMPORTANT! Do not run engine with high or low oil levels as this will cause engine damage. Cold Water Source Garden Hose STEP 3: Connect garden hose to the cold water source and turn water on completely. Never use hot water. STEP 4: Trigger the spray gun to eliminate trapped air then wait for a steady flow of water to emerge from the spray nozzle. Choke Knob Fuel Valve STEP 5: Rotate the fuel shut-off valve to the "On" position. Slide the fuel valve lever to the "ON" position. When the engine is not in use, leave the fuel valve in the "OFF" position. STEP 6: Pull the choke knob out to the "Choke" position (on a warm engine, when in the run position, leave the choke knob in). Push the choke knob to the "Closed" position. To restart a warm engine, leave the choke knob in the "Open" position. 96-718, 97-721, 97-723 • REV. 8/05a 9 PRESSURE WASHER OPERATOR’S MANUAL OPERATING INSTRUCTIONS (CON'T) On-Off Switch STEP 7: Turn the engine switch to "ON" position. STEP 8: Pull the starter grip. If the engine fails to start after 2 pulls, squeeze the trigger gun to release pressure and repeat step. Return starter gently. After the engine warms up enough to run smoothly, move choke to run position and throttle to fast position. CAUTION: Small engines may kick back. Do not hold pull starter grip tightly in hand. NOZZLES Safety Latch WARNING! Never replace noz zles without engaging the safe ty latch on the spray gun trigger. The five color-coded quick connect nozzles provide a wide array of spray widths from 0° to 45° and are easily accessible when placed in the convenient rubber nozzle holder, which is provided on the front of the machine. NOTE: For a more gentle rinse, select the white 40° or green 25° nozzle. To scour the surface, select the yellow 15° or red 0° nozzle. To apply detergent select the black nozzle. 10 96-718, 97-721, 97-723 • REV. 8/05a WARNING WARNING: Some detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause prop er ty dam age or severe injury. Discharge Nipple Detergent Injector Quick Coupler High Pressure Hose Filter Soap Nozzle STEP 2: Use detergent designed specifically for pressure washers. Household detergents could damage the pump. Prepare detergent solution as required by the manufacturer. Fill a container with pressure washer detergent. Place the filter end of detergent suction hose into the detergent container. STEP 3: With safety latch on spray gun engaged, secure black soap nozzle into quick coupler. NOTE: Detergent cannot be applied using red, yellow, green or white nozzles. STEP 4: With the engine running, pull trigger to operate machine. Liquid detergent is drawn into the machine and mixed with water. Apply detergent to work area. Do not allow detergent to dry on surface. IMPORTANT:You must flush the detergent injection system after each use by placing the suction hose into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes. If you run the engine on your pressure washer for 3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach high temperatures. When the water reaches this temperature, the pump protector engages and cools the pump by discharging the warm water onto the ground. This thermal device prevents internal damage to the pump. CLEANING TIPS Pre-rinse cleaning surface with fresh water. Place detergent suction tube directly into cleaning solution and apply to surface at low pressure (for best results, limit your work area to sections approximately 6 feet square and always apply detergent from bottom to top). Allow detergent to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. If surface appears to be drying, simply wet down surface with fresh water. If needed, use brush to remove stubborn dirt. Rinse at high pressure from top to bottom in an even sweeping motion keeping the spray nozzle approximately 1 foot from cleaning surface. Use overlapping strokes as you clean and rinse any surface. For best surface cleaning action spray at a slight angle. OPERATOR’S MANUAL STEP 1: Connect detergent injector to discharge nipple on machine. Connect high pressure hose to injector with quick coupler. (Check to make sure locking coupler sleeves are in proper position before applying water pressure). THERMAL PUMP PROTECTION PRESSURE WASHER APPLYING DETERGENT AND GENERAL CLEANING TECHNIQUES Recommendations: • Before cleaning any surface, an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results. • If painted surfaces are peeling or chipping, use extreme caution as pressure washer may remove the loose paint from the surface. • Keep the spray nozzle a safe distance from the surface you plan to clean. High pressure wash a small area, then check the surface for damage. If no damage is found, continue to pressure washing. CAUTION - Never use: • Bleach, chlorine products and other corrosive chemicals • Liquids containing solvents (i.e., paint thinners, gasoline, oils) • Tri-sodium phosphate products • Ammonia products • Acid-based products These chemicals will harm the machine and will damage the surface being cleaned. RINSING It will take a few seconds for the detergent to clear. Apply safety latch to spray gun. Remove black soap nozzle from the quick coupler. Select and install the desired high pressure nozzle. NOTE: You can also stop detergent from flowing by simply removing detergent siphon hose from bottle. 96-718, 97-721, 97-723 • REV. 8/05a 11 PRESSURE WASHER OPERATOR’S MANUAL SHUTTING DOWN AND CLEAN-UP On-Off Switch STEP 1: Remove detergent suction tube from container and insert into one gallon of fresh water. Slide nozzle forward for low pressure or to connect black detergent nozzle. Pull trigger on spray gun and siphon water for one minute. STEP 2: Turn engine switch to "OFF" position. STEP 3: Turn off water supply. Discharge Nipple Safety Latch Water Inlet STEP 4: Press trig ger to re lease water pressure. STEP 5: Disconnect the garden hose from the water inlet on the machine. STEP 6: Disconnect the high STEP 7: En gage pres sure hose from the dis- the spray gun safety charge nipple. lock. STORAGE CAUTION: Always store your pressure washer in a location where the temperature will not fall below 32°F (0°C). The pump in this machine is susceptible to permanent damage if frozen. FREEZE DAMAGE IS NOT COVERED BY WARRANTY. 1. Stop the pressure washer, squeeze spray gun trigger to release pressure. 2. Detach water supply hose and high pressure hose. 3. Turn on the machine for a few seconds, until remaining water exits. Turn engine off immediately. 4. Drain the gas and oil from the engine. 5. Do not allow high pressure hose to become kinked. 6. Store the machine and accessories in a room which does not reach freezing temperatures. CAUTION: Failure to follow the above directions will result in damage to your pressure washer. When the pressure washer is not being operated or is being stored for more than one month, follow these instructions: 12 1. Replenish engine oil to upper level. 2. Drain gasoline from fuel tank, fuel line, fuel valve and carburetor. 3. Pour about one teaspoon of engine oil through the spark plug hole, pull the starter grip several times and replace the plug. Then pull the starter grip slowly until you feel increased pressure which indicates the piston is on its compression stroke and leave it in that position. This closes both the intake and exhaust valves to prevent rusting of cylinder. 4. Cover the pressure washer and store in a clean, dry place that is well ventilated away from open flame or sparks. NOTE: The use of a fuel additive, such as STA-BIL®, or an equivalent, will minimize the formulation of fuel deposits during shortage. Such additives may be added to the gasoline in the fuel tank of the engine, or to the gasoline in a storage container. After Extended Storage CAUTION: Prior to restarting, thaw out any possible ice from pressure washer hoses, spray gun or wand. Engine Maintenance During the winter months, rare atmospheric conditions may develop which will cause an icing condition in the carburetor. If this develops, the engine may run rough, lose power and may stall. This temporary condition can be overcome by deflecting some of the hot air from the engine over the carburetor area. NOTE: Refer to the engine manufacturer's manual for service and maintenance of the engine. 96-718, 97-721, 97-723 • REV. 8/05a PROBLEM POSSIBLE CAUSE SOLUTION LOW OPERATING PRESSURE Insufficient water supply. Closed faucet. Inlet hose kinked Use larger garden hose; clean inlet water screen. Open faucet. Clogged inlet hose strainer Check plumbing system for leaks. Retape leaks with teflon tape. Faulty or misadjusted unloader valve Adjust unloader for proper pressure. Install repair kit when needed. Call technical support. Worn packing in pump Call technical support. Machine has been stored in freez- Thaw out machine completely, including ing temperatures. hose, spray gun and wand. Slow engine RPM Call technical support. Worn or dirty pump valves Call technical support. Nozzle is obstructed Use nozzle wire in accessory kit. Pump sucking air, inlet hose leaking Check all pump lines and connections. PRESSURE LOW AFTER PERIOD OF NORMAL USE Nozzle worn Replace nozzle. Unloader valve worn Replace unloader valve. ENGINE WILL NOT START OR STOPS WHILE OPERATING Low oil shutdown Fill engine with oil. Water in gasoline Drain gas tank; fill with clean fuel. Out of gas Fill fuel tank. ENGINE IS OVERLOADED Nozzle partially blocked Clean nozzle. Excessive pressure from high engine RPM Adjust engine throttle to lower RPM. WATER OR OIL LEAKING FROM BOTTOM OF PUMP A small amount of leaking is normal If excessive leaking occurs, call technical support. PRESENCE OF WATER IN PUMP OIL Water sprayed at machine Change oil. Direct spray away from machine. High humidity in air Check and change oil twice as often. Piston packing worn. Oil seal worn Call technical support. FLUCTUATING PRESSURE PRESSURE WASHER Troubleshooting Guide TROUBLESHOOTING 13 96-718, 97-721, 97-723 • REV. 8/05a PRESSURE WASHER OPERATOR’S MANUAL TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION ENGINE OPERATES FOR 15 MIN. THEN STOPS Not enough gas or engine oil Fill tank with gas. Check oil level. Vapor lock developed by heat of day Keep gas tank full to avoid vapor locking. Obstruction in fuel filter Clean or replace fuel filter. ENGINE LACKS POWER Dirty air filter Replace air filter. ENGINE FALTERS Choke is opened too soon Move choke to halfway position until engine runs smoothly. WATER DRIPPING FROMUNDER PUMP Piston packing worn Call technical support. O-Ring plunger retainer worn Call technical support. Cracked piston Call technical support. OIL DRIPPING Oil seal worn or damaged Call technical support. WATER LEAKING FROM PUMP PROTECTOR Spray gun closed with machine running 5 minutes or longer Open spray gun or turn off machine. Excess water supply pressure Place a pressure regulator at end of 50’ garden hose. Detergent suction tube not properly connected to machine Check connection. Detergent is too thick Dilute detergent. For best results, use Rhino detergent. Detergent filter valve is at lowest setting Set detergent filter valve to a higher setting. Filter on detergent suction tube is clogged Run warm water through filter to remove debris. Damaged or clogged detergent suction tube Remove obstruction or replace detergent suction tube. A high pressure nozzle is attached. Replace with black detergent nozzle. Discharge nozzle is obstructed Blow out or remove debris with fine needle. GARDEN HOSE CONNECTION LEAKS Loose fittings Tighten fittings. Missing/worn rubber washer Insert new washer. SPRAY WAND LEAKS Spray wand not properly attached Slide the spray wand into the gun. Turn the wand collar clockwise onto the spray gun threads until tight. Broken o-ring Call customer service and order an o-ring. Pump is sucking air Check that hoses and fittings are air tight. Turn off machine and purge pump by squeezing trigger gun until a steady flow of water emerges through nozzle. NO DETERGENT PUMP IS NOISY 14 96-718, 97-721, 97-723 • REV. 8/05a This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer. Perform maintenance more often under severe conditions. Pump Oil Inspect Daily inspect the oil level Change After first 50 hours, then every 500 hours or annually Every 6 months Replace quick connects Annually Clean water screen/filter Weekly Replace HP hose Annually if there is any sign of wear Grease motor Every 10,000 hours OPERATOR’S MANUAL Replace high pressure nozzle PRESSURE WASHER PREVENTATIVE MAINTENANCE OIL CHANGE RECORD Check pump oil and engine oil level before first use of your new pressure washer. Date Oil Changes Month/Day/Year Estimated Operating Hours Since Last Oil Change Date Oil Changes Month/Day/Year Estimated Operating Hours Since Last Oil Change 15 96-718, 97-721, 97-723 • REV. 8/05a PRESSURE WASHER EXPLODED VIEW - LARGE 4 57 55 37 79 73 34 88 38 35 36 5 2 56 57 31 OPERATOR’S MANUAL 42 All Models 76 Except 4040 26 73 57 52 59 32 28 43 60 39 75 16 40 20 23 84 59 33 18 16 18 62 45 77 23 10 19 12 15 53 9 45 8, 9 50 22 343087E,343089E, 404027, 404029 Models 1 3 21 65 18 13 82 78 27 44 71 8 50 14 Models 404027, 404029 61 22 7 54 59 60 53 59 89 80 17 42 6 48 47 74 74 48 59 51 60 29 69 74 48 74 71 74 29 72 51 70 87 25 72 58 48 68 49 74 48 46 81 74 48 60 49 49 48 59 30 64 24 11 58 86 70 67 66 85 16 96-718, 97-721, 97-723 • REV. 8/05a 59, 60, 61 ITEM PART NO. 1 DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY Label, This Tank For Gas Only (455037E, 455039E, 455034E) 1 19 2-10942 Swivel, 1/2"MP x 3/4" GHF w/Strainer 10-020090 Label, Diesel (343087E, 343089E) 20 2-1105 Swivel, 1/2" JIC Fem, Push-On 2 1 21 2-1923 Strainer, 1/2" PA, Inline Plastic 22 2-20022 Nipple, 3/8" Fem, 11,000 PSI” (405039E, 455039E, 455034E, 455037E) 1 2-2007 Nipple, 3/8" x 3/8" NPT ST Male (404027, 404029, 343087E, 343089E) 1 2-30082 Pump Protector, 1/2" PTP (405039E, 455039E, 455034E, 455037E) 1 2-300816 Pump Protector, 3/8" (404027, 404029, 343087E, 343089E) 2 10-02025A Label, “Hot/Caliente” w/Arrows 1 3 10-02029 Label, Danger Cool Engine (455037E, 405039E, 455039E 455034E) 1 4 11-01011 Label, Warning Pictoral(Small) 1 5 11-013 ▲ Label, Logo, Belt Guard (BR) 1 10-03014 ▲ Label, Logo, Belt Guard (MP) 1 11-3227 ▲ Label, Logo, Belt Guard (BD) 1 23 1 1 1 24 2-90151 Clamp, Snap-In Wire (343087E, 343089E, 405039E, 455039E, 455034E, 455037E) 2 1 25 2-9016 Clamp, Round, 0.56 I.D. (405039E, 455039E, 455034E, 455037E) 1 1 26 4-02047914 Hose, 3/8" x 14", 2 Wire, Pressure Loop (405039E, 455034E 455037E, 455039E) 1 6 11-0316 Label, Instructions 1 7 10-03008 Label, Nozzle Identification 1 8 2-0051 Nipple, 1/2” JIC, 3/8” Pipe 9 2-0079 Swivel, 1/2" JIC Fem, 3/8" Male 10 2-010061 Bushing, Rubber, Nitrile (405039E, 455039E, 455034E, 455037E) 1 (343087E, 343089E) 2 11 2-0103 Grommet, Rubber, Nozzle Holder 12 2-011507 Tank, Encore 5 Gal. Tank (343087E, 343089E, 405039E, 455039E, 455034E) 1 27 4-02100000 Hose, 1/4", Push-On, Fuel Line (343087E, 343089E, 405039E, 455039E, 455034E, 455037E)4.75 ft. 13 2-01167 Cap, Fuel Tank, Plastic (343087E, 343089E, 405039E, 455039E, 455034E, 455037E) 1 28 4-02110000 Hose, 1/2", Push-On 29 4-0307 30 4-12803500 Nozzle, SACQMEG, 0003.5, Red (405039E) 1 4-12803515 Nozzle, SAQCMEG 1503.5, Yellow (405039E) 1 4-12803525 Nozzle, SAQCMEG, 2503.5, Green (405039E) 1 4-12803540 Nozzle, SAQCMEG 4003.5, White (405039E) 1 2-0117 Battery, Box (343087E, 343089E, 405039E, 455039E, 455034E, 455037E) 1 15 2-011700 Plate, Battery Box, Small, Polypro (343087E, 343089E, 405039E, 455039E, 455034E, 455037E) 1 16 2-0051 Nipple 1/2" JIC x 3/8" Male (343087E,343089E,404027, 404029) 2-00510 Nipple, 1/2" JIC x 3/8" Fem (405039E, 455034E, 455037E, 455039E) 1 17 2-0155 Fastener, Ratchet, Black Nylon 2 18 2-1062 Elbow, 1/2" JIC x 1/2", 90° (405039E, 455034E, 455037E 455039E) 2 (343087E, 343089E, 404027, 404029) 1 Elbow, 1/2” JIC x 3/8”, 90° (404027, 404029, 343087E, 343089E) 1 2-1060 4-02047714 Hose, 3/8" x 1/4", 2 Wire Pressure (343087E, 343089E, 404027, 404029) 1 5 14 OPERATOR’S MANUAL 10-02011 PRESSURE WASHER EXPLODED VIEW PARTS LIST- LARGE Wheel & Tire Cmpl, 6" 1.25 ft. 4 1 17 96-718, 97-721, 97-723 • REV. 8/05a ITEM PART NO. OPERATOR’S MANUAL PRESSURE WASHER EXPLODED VIEW PARTS LIST- LARGE DESCRIPTION QTY DESCRIPTION QTY 4-12804000 Nozzle, SAQCMEG 0004, Red (343087E,343089E,404029, 404027,455039E,455034E, 455037E) 1 4-12804015 Nozzle, SAQCMEG 1504, Yellow (343087E,343089E,404029, 404027,455039E,455034E, 455037E) 1 4-12804025 Nozzle, SAQCMEG 2504, Green (343087E,343089E,404029, 404027,455039E,455034E, 455037E) 1 4-12804040 Nozzle, SAQCMEG 4004, White (343087E,343089E,404029, 404027,455039E,455034E, 455037E) 1 46 51 95-07393125 Axle, 5/8" x 31.25" 2 4-16540 52 95-07104036 Guard, Belt, Rear Steel 1 53 95-07162047 Assy, Weld, Battery Brkt, CW Cage, Red (343087E, 343089E, 405039E, 455039E, 455037E) 1 Nozzle COMPL, QCEM-6540, Brass (404029, 455039E, 405039E, 343089E, 455034E, 455037E, 455037E) 1 31 Engine, See Specifications Pages 32 Pump, See Specifications Pages 33 Unloader, See Specifications Pages 34 Engine Pulley, See Specifications Pages 35 Pump Pulley, See Specifications Pages 36 Pump Bushing, See Specifications Pages 37 Engine Bushing, See Specifications Pages 38 Belts, See Specifications Pages 39 6-05109 40 ITEM PART NO. 6-051092 90-102746 Bolt, 1/2" x 5" NC HH Tap (404027, 404029, 405039E, 455039E, 455034E, 455037E) 1 90-102751 Bolt, 1/2" x 3-1/2", NC, HH (343087E, 343089E) 47 90-18012 Screw, 1/4" x 5/8", Phil PH MS (343087E, 343089E, 405039E, 455034E, 455037E, 455039E) 4 48 90-20041 Collar, 5/8" Bore Shaft 49 90-40181 Washer , Nylon Spacer, 0.656 x 1.25 x 0.65 THK 4 50 95-07101216/B Block, Unloader, 3/8" x 3/8" Brass 54 55 Cable, Battery, 32" Red, 4 Gauge (343087E, 343089E, 405039E, 455039E, 455034E 455037E) 1 56 Cable, Battery, 36" Black, 4 Gauge (343087E, 343089E, 405039E, 455039E, 455034E, 455037E) 1 1 8 1 95-07162048 Assy, Weld, Battery Brkt, CW Cage, Black (455034E) 1 95-07162081 Holder, Nozzle (404027 404029) 1 95-07162054 Assy, Weld, Cage, CW Red (BD, BR) 95-07162055 Assy. Weld, Cage, CW Black (MP) 95-07162045 Guard, Belt, Front, CW Cage, Black 1 1 1 95-07162071 Assy, Weld, Slider, CW Cage, Red (404029, 405039E, 455037E, 455039E, 404027) 1 95-07162072 Assy, Weld, Slider, CW Cage, Black (455034E) 1 95-07162096 Slider, Assy., Welded, 10HP Lombardini (343087E,343089E) 1 41 2-30057 Valve, Shut-Off, 1/4 Turn 1 42 90-1007 Bolt, 5/16" x 1", NC HH (343087E, 343089E) 6 57 90-1995 Screw, 1/4" x 1/2" BH SOC CS 7 (405039E, 455039E, 455034E, 455037E) 4 58 90-2000 Nut, 1/4" ESNA, NC 59 90-4001 Washer, 5/16" FLAT, SAE (343087E, 343089E, 405039E, 455034E, 455037E, 455039E) 20 (404027,404029) 16 59 90-4002 Washer, 3/8" (404027, 404029) 2 (343087E, 343089E, 405039E, 455034E, 455037E, 455039E) 10 60 90-2001 Nut, 5/16" ESNA, NC (404027, 404029) 10 (343087E, 343089E) 14 (405039E, 455034E, 455037E, 455039E) 12 90-2002 Nut, 3/8" ESNA (404027, 404029) 2 (343087E, 343089E, 405039E, 455034E, 455037E, 455039E) 6 43 (404027,404029) 2 90-1010 Bolt, 5/16" x 1-3/4", NC HH (404027, 404029) 4 90-1019 Bolt, 3/8" x 1-3/4" (343087E, 343089E) 4 43 90-1020 Bolt, 3/8" x 2", NC, HH (405039E, 455034E, 455037E, 455039E) 4 44 2-010066 Elbow, Fuel Tank, Zinc (343087E, 343089E) 1 45 90-1020 Bolt, 3/8" x 2" NC, HH 2 18 96-718, 97-721, 97-723 • REV. 8/05a 4 ITEM PART NO. 61 90-100543 DESCRIPTION QTY Screw, 5/16"-18 x 3/4" M PH TRH 4 62 2-1046 Plug, 1/4" Countersunk (405039E, 455034E,455037E, 455039E) 1 63 90-400910 ▲ Washer, 7/16" Lock-Split Ring 4 ITEM PART NO. DESCRIPTION QTY 78 2-0053 Elbow, 1/2" JIC, 3/8", 90° 1 79 77-VHRM4 Muffler, Honda, GX620/670 Right (405039E, 455037E, 455039E, 455034E) 1 76-807964 ▲ Muffler, Exhaust, Briggs 16HP (404029, 404027) 1 ▲ Bolt, 10mm x 20mm, HH 4 2-01103 Grip, 1" Square Handle 2 95-07101149 ▲ Guard, Muffler, Briggs 16HP (404029, 404027) 1 65 2-10323 Tee, 1/2", Branch Male 1 66 95-07104828 Bracket, Brake Pad, Red (BD, BR) 95-071011491▲ Brace, Muffler Guard (404029, 404027) 2 1 76-495518 95-07164828 Bracket, Brake Pad, Black (MP) 1 67 ▲ Muffler, Deflector, Vanguard (404027, 404029) 1 79-11465813800 ▲ Deflector, Exhaust, Honda (405039E, 455037E, 455039E, 455034E) 1 95-07164829 Linkage, Brake, Black (MP) 1 95-07104829 Linkage, Brake, Red (BD, BR) 1 68 90-3096 1 69 95-07162065 Handle, Break, CW Cage, Red (BD, BR) 1 95-07162066 Handle, Break, CW Cage, Black (MP) 1 82 4-02100000 Hose, 1/4 Push-On (343087E, 343089E) 7.66 ft. 83 2-00471 Plug, 1/8" Square Head, Black (343087E, 343089E, 405039E, 455037E,455039E, 455034E) 1 84 2-1100 Adaptor, 1/2 x 1/2 (455037E, 343087E, 404027, 404029, 455039E, 343089E, 455034E) 1 2 Washer, 1/2" Flat 70 90-100472 Bolt, Carriage, Zinc, 1/4"-20 x 1.0 PLT 4 71 2-9040 Clamp, Hose, .46-.54 ST (405039E, 455039E, 455034E, 455037E) 2 (343087E, 343089E) 4 80 10-9999 Clear Lexan 1 81 10-08017 Label, Intended For Outdoor Use 1 72 90-4000 Washer, 1/4" Flat, SAE 12 73 90-40001 Washer, 1/4" FLAT, SAE, Black, Zinc 5 85 90-19980 Screw, 1/4" x 1" (405039E, 455034E, 455037E, 455039E) 90-40001 Washer, 1/4" Flat, SAE, Black (405039E, 455034E, 455037E, 455039E) 2 90-2000 Nut, 1/4" ESNA (405039E, 455034E, 455037E, 455039E) 74 90-4005 Washer, 5/8" Flat 8 86 75 1-100534 Valve, Safety Relief, 6000PSI (405039E, 455039E, 455034E, 455037E) 1 87 Elbow, 3/8" Street (405039E, 455039E, 455034E, 455037E) 1 88 95-07162057 Bracket, Regulator Nipple, 3/8" Hex Steel (405039E, 455037E, 455039E, 455034E) 1 89 9.800-049.0 Label, Manufacturer's Cleaning Solution 1 76 77 2-0031 2-0006 OPERATOR’S MANUAL 90-10343 64 PRESSURE WASHER EXPLODED VIEW PARTS LIST- LARGE 2 1 ▲ Not Shown 19 96-718, 97-721, 97-723 • REV. 8/05a OPERATOR’S MANUAL PRESSURE WASHER EXPLODED VIEW - SMALL 5 56 34 41 7 35 1 32 15 29 33 36 41 55 51 56 2 26 37 56 25 37 30 56 21 45 19 21 9 18 22 57 48 37 40 17 10 20 24 11 9 23 31 9 50 24 Model 442539 18 38 53 10 31 9 50 23 11 16 4 14 43 3 28 12 49 6 49 43 44 58 46 42 43 27 43 54 45 27 8 39 13 52 47 38 20 96-718, 97-721, 97-723 • REV. 8/05a ITEM PART NO. DESCRIPTION QTY 10-02025A Label, "Hot/Caliente" w/Arrows Warning 1 2 10-02029 Label, Danger Cool Engine 3 10-08017 Label, Intended For Outdoor Use1 4 10-9999 Label, Clear Lexan, 2-1/4" x 4-1/2" 5 11-01011 Label, Warning, Pictoral, Small 1 6 11-0316 Label, Instructions 7 10-0623 Label, Belt Guard, MP (353234, 373534, 442534) 1 11-32289 Label, Belt Guard, BD (353239, 373539) 1 11-3229 Label, Belt Guard, BR (442537, 353237,373537) 1 8 10-03008 ITEM PART NO. QTY 4-12805500 Nozzle, SAQCMEG 0005.5, Red (442534,442537) 1 4-12805515 Nozzle, SAQCMEG 1505.5, Yellow (442534,442537) 1 4-12805525 Nozzle, SAQCMEG 2505.5, Green (442534,442537) 1 4-12805540 Nozzle, SAQCMEG 4005.5, White (442534,442537) 1 4-16540 Nozzle, COMPL, QCEM-6540, Brass (BD383239,BD373539, BD442539) 1 29 Engine, See Specifications Pages 30 Pump, See Specifications Pages 31 Unloader, See Specifications Pages 32 Engine Pulley, See Specifications Pages 1 33 Pump Pulley, See Specifications Pages Engine Bushing, See Specifications Pages 1 1 1 Label, Nozzle Identification DESCRIPTION 28 9 2-0051 Nipple, 1/2" JIC, 3/8" Pipe 2 34 10 2-0053 Elbow, 1/2" JIC, 3/8", 90° 1 35 Pump Bushing, See Specifications Pages Belt, See Specifications Pages 11 2-0079 Swivel, 1/2" JIC Fem, 3/8" Male 1 36 12 2-0103 Grommet, Rubber, Nozzle Holder 37 90-1020 Bolt, 3/8" x 2" NCHH 6 5 38 90-1018 Bolt, 3/8" x 1-1/2", NC HH 2 13 2-01041 Pad, Soft Rubber, 50 Duro 2 39 90-102751 Bolt, 1/2" x 3-1/2", NC HH 1 14 2-01103 Grip, 1" Square, Handle 2 40 90-10343 Bolt, 10mm x 20mm, HH 4 15 2-0117200 Belt Guard, CW 1 41 90-19710 16 2-0155 Fastener, Ratchet, Black Nylon 2 Screw, 1/4" x 3/4" HH NC, Whiz Loc 3 17 2-10323 Elbow, 1/2" Street, Brass 1 42 90-2002 Nut, 3/8" ESNA, NC 4 90-20041 Collar, 5/8" Bore Shaft 3010 4 18 2-1060 Elbow, 1/2" JIC x 3/8", 90° 1 43 19 2-1062 Elbow, 1/2" JIC x 1/2", 90° 1 44 90-3096 Washer, 1/2" Flat 1 45 90-4002 Washer, 3/8" Flat, SAE 8 20 2-10942 Swivel, 1/2" MP x 3/4" GHF w/Strainer 1 46 90-4002 Washer, 3/8" SAE, Flat 2 21 2-1105 Swivel, 1/2" JIC Fem, Push-On 2 47 90-40125 Washer, 3/8" x 1" 2 22 2-1923 Strainer, 1/2" PA, Inline Plastic 1 48 90-400910 Washer, 7/16", Lock Split Ring 4 23 2-2007 Nipple, 3/8" x 3/8" NPT ST Male 49 90-40181 1 Washer, Nylon Spacer, 0.656" x 1.25" x 0.65" Thick 2 Pump Protector, 3/8" PTP 1 50 95-07101216/B Block, Unloader, 3/8" x 3/8" Brass 1 51 95-07104001 Slider, Pump/Belt Guard Mount, Red (BD, BR) 1 95-07104033 Slider, Pump/Belt Guard Mount, Black (MP) 1 52 95-07104723 Axle, 5/8" x 27.80 L 1 53 95-07162004 Assy, Weld, CW Cage, Small Red (BD, BR) 1 24 2-300816 25 4-02047720 Hose, 3/8" x 20", 2 Wire, Pressure Loop 26 4-02110000 Hose, 1/2", Push-On 1.25 ft. 27 4-0307 28 4-12804000 Nozzle, SAQCMEG 0004, Red (353239,373539,353237, 373534,353234,373537) 1 4-12804015 Nozzle, SAQCMEG 1504, Yellow (353239,373539,353237, 373534,353234,373537) 1 4-12804025 Nozzle, SAQCMEG 2504, Green (353239,373539,353237, 373534,353234,373537) 1 4-12804040 Nozzle, SAQCMEG 4004, White (353239,373539,353237,373534, 353234,373537 ) 1 Wheel & Tire Assy, 6" Steel Rim w/Tube 2 1 95-07162005 Assy, Weld, CW Cage, Small Black (MP) 1 54 90-2002 Nut, 3/8" ESNA, NC 2 55 90-2001 Nut, 5/16" ESNA 4 56 90-4001 Washer, 5/16" Flat 7 96-718, 97-721, 97-723 • REV. 8/05a OPERATOR’S MANUAL 1 PRESSURE WASHER EXPLODED VIEW PARTS LIST- SMALL 21 ITEM PART NO. 57 58 DESCRIPTION QTY 2-1102 Adapter, 1/2" Female x 3/8" Male (343089E,442534) 1 2-1100 Adapter, 1/2 x 1/2 (353234, 373534, 353237, 442537, 373539) 1 9.800-049.0 Label, Manufacturer's Cleaning Solution 1 OPERATOR’S MANUAL PRESSURE WASHER EXPLODED VIEW PARTS LIST- SMALL 22 96-718, 97-721, 97-723 • REV. 8/05a PRESSURE WASHER HOSE & SPRAY GUN ASSEMBLY 1, 2 4 9 3 1, 2 8 6 OPERATOR’S MANUAL 10 7 7 5 HOSE & SPRAY GUN ASSEMBLY PARTS LIST ITEM PART NO. 1 DESCRIPTION QTY 4-0110331 Wand, Side Grip w/Couplers 47.5" (373539, 404029, 343089E) 1 4-012192 Spray Gun w/Wand (5000 PSI), w/Coupler (405039E, 455039E, 455034E, 455037E) 1 4-011143A Wand, SS V.P. Wand, (AL 344) w/Coupler, w/Soap Nozzle (353234, 373534, 442534) 1 4-0111341A Wand, V.P. w/Coupler & Nozzle, X-Series (353237, 373537, 404027, 343087E, 442537) 1 2 4-012402 4-01246 4-01212 3 3 Spray Gun, Shut-Off, AP 1000 (442537, 353237, 373537, 404027, 343087E) 1 Gun, Shut-Off (373534, 353234, 442534) 1 4-02043450F Hose, 3/8" x 50 ft., 2 Wire, TUFFSkin, w/5800 PSI Coupler (405039E, 455039E, 455034E, 455037E) 1 4-020750C DESCRIPTION QTY Hose, 3/8" x 50 ft., 2 Wire, Pressure Flex, w/Coupler (353237, 373537, 373539, 404029, 353234, 373534) 1 4-02093450BC Hose, 3/8" x 50 ft., 1 Wire Blue, w/Coupler (442537, 353237, 343087E) 1 4-02073450RC Hose, 3/8" x 50 ft., 2 Wire Blue, w/Coupler (373537, 404027) 1 4 Spray Gun Assy, w/Nipple (373539, 404029, 343089E) 1 4-02033450C Hose, 3/8" x 50 ft., 1 Wire, TUFFSkin, w/Coupler (442534, 343089E) 1 4-020650C ITEM PART NO. 3-12021 Injector, Detergent, Non-Adj, 3-5 GPM, 0.083 1 3-1208 Injector, SS, Non-Adj, 2.0-4.0GPM, 5500PSI 1 5 2-1904 6 4-02080000 Tube, 1/4" x 1/2", Clear Vinyl 7 2-9040 Clamp, Hose, .46-.54 ST 8 2-20021 Coupler, 3/8" Female, 11,000 PSI, Snap-Tite (405039E, 455034E, 455037E, 455039E) 1 9 2-20022 Nipple, 3/8" Fem, 11,000 PSI (405039E, 455034E, 455037E, 455039E) 1 10 4-011184 Detergent Injector Assy, 3-5 GPM, 0.83" (353239, 373539, 404029, 343089E, 353234, 373534, 353237, 373537, 343087E, 404027, 442537) 1 4-011186 Downstream Injector Assy, 5000 PSI (405039E, 455039E, 455034E, 455037E) 1 Hose, 3/8" x 50", 1 Wire, Pressure Flex, w/Coupler (343087E) 1 Strainer, Plastic, 1/4" Hose Barb 1 6 ft. 2 23 96-718, 97-721, 97-723 • REV. 8/05a PRESSURE WASHER OPERATOR’S MANUAL SPECIFICATIONS Machine Engine Pulley Engine Bushing Pump Pump Pump Bushing Model Pulley Desc. Bushing# Desc. Pulley Desc. Bushing# Desc. 373539 5-40503201 2BK32H 5-511100 Hx1" 5-40509001 2BK90H 5-512024 24mm 404029 5-40503601 2BK36H 5-511100 Hx1" 5-40509001 2BK90H 5-512025 25mm 405039E 5-407034 3TB34 5-531112 P2x1" 5-41009001 3BK90H 5-512025 25mm 455039E 5-407034 3TB34 5-531113 P2x1-1/8" 5-41008001 3BK80H 5-512025 25mm 343089E 5-40504001 2BK40H 5-511100 Hx1" 5-40508001 2BK80H 5-5120220 22mm 353234 5-40503201 2BK32H 5-511100 Hx1" 5-40509001 2BK90H 5-512025 25mm 373534 5-40503201 2BK32H 5-511100 Hx1" 5-40509001 2BK90H 5-512025 25mm 455034E 5-407034 3TB34 5-531113 P2x1-1/8" 5-41008001 3BK80H 5-512025 25mm 304037 5-40504001 2BK40H 5-511100 Hx1" 5-40508001 2BK80H 5-512024 24mm 353237 5-40503201 2BK32H 5-511100 Hx1" 5-40509001 2BK90H 5-512024 24mm 373537 5-40503201 2BK32H 5-511100 Hx1" 5-40509001 2BK90H 5-512024 24mm 455037E 5-407034 3TB34 5-531113 P2x1-1/8" 5-41008001 3BK80H 5-512025 25mm 442537 5-40503201 2BK32H 5-511100 Hx1" 5-40508001 2BK80H 5-512024 24mm 404027 5-40503401 2BK34H 5-511100 Hx1" 5-40509001 2BK90H 5-512025 25mm 343087E 5-40503201 2BK32H 5-511100 Hx1" 5-40509001 2BK90H 5-512024 24mm 24 96-718, 97-721, 97-723 • REV. 8/05a Machine Model Belt (QTY) Pump Unloader Engine Desc. Belt Part No. Part No. Part No. 373539 5-604039 (2) BX39 5-1220 5-32080 5-010721 404029 5-604042 (2) BX42 5-1808 5-32080 5-0306 5-604042 (3) BX42 5-1238 5-3014 5-01093 5-604042 (3) BX42 5-1238 5-3014 5-01094 343089E 5-604042 (2) BX42 5-1803 5-32080 5-0413 353234 5-604039 (2) BX39 5-1724 5-32080 5-0105 373534 5-604039 (2) BX39 5-1724 5-32080 5-010721 455034E 5-604042 (3) BX42 5-1738 5-3014 5-01094 304037 5-604038 (2) BX38 5-1912 5-32080 5-010721 353237 5-604039 (2) BX39 5-1920 5-32080 5-0105 373537 5-604039 (2) BX39 5-1920 5-32080 5-010721 455037E 5-604042 (3) BX42 5-1938 5-3014 5-01094 442537 5-604037 (2) BX37 5-1915 5-32080 5-0105 404027 5-604043 (2) BX43 5-1924 5-32080 5-0306 343087E 5-604042 (2) BX42 5-1920 5-32080 5-0413 OPERATOR’S MANUAL 405039E 455039E PRESSURE WASHER SPECIFICATIONS 25 96-718, 97-721, 97-723 • REV. 8/05a WARRANTY SHARK LIMITED NEW PRODUCT WARRANTY PRESSURE WASHERS WHAT THIS WARRANTY COVERS All SHARK PRESSURE WASHERS are warranted by SHARK to the original purchaser to be free from defects in materials and workmanship under normal use, for the periods specified below. This Limited Warranty is subject to the exclusions shown below, is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced under this warranty will assume the remainder of the part’s warranty period. This warranty applies to the original purchaser and is not transferable. LIMITED LIFETIME PARTS WARRANTY: Components manufactured by SHARK, such as frames, handles, and belt guards. Forged brass pump manifold. All heating coils will have a three year warranty. Internal components (excluding oil seals) on the oil-end of all pressure washer pumps will have a seven year warranty. ONE YEAR PARTS WARRANTY: All other components, excluding normal wear items as described below, will be warranted for one year on parts. Warranty on these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty. WARRANTY PROVIDED BY OTHER MANUFACTURERS: Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manufacturers’ local authorized service centers. SHARK cannot provide warranty on these items. WHAT THIS WARRANTY DOES NOT COVER This warranty does not cover the following items: 1. Normal wear items, such as nozzles, guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings, packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protectors. 2. Damage or malfunctions resulting from accidents, abuse, modifications, alterations, incorrect installation, improper servicing, failure to follow manufacturer’s maintenance instructions, or use of the equipment beyond its stated usage specifications as contained in the operator’s manual. 3. Damage due to freezing, chemical deterioration, scale buildup, rust, corrosion, or thermal expansion. 4. Damage to components from fluctuations in electrical or water supply. 5. Normal maintenance service, including adjustments, fuel system cleaning, and clearing of obstructions. 6. Transportation to service center, shop labor charges, field labor charges, or freight damage. WHAT YOU MUST DO TO OBTAIN WARRANTY SERVICE While not required for warranty service, we request that you register your SHARK pressure washer by returning the completed registration card. In order to obtain warranty service on items, you must return the product to an Authorized SHARK Dealer, freight prepaid, with proof of purchase, within the applicable warranty period. If the product is permanently installed, you must notify your Authorized SHARK Dealer of the defect. The Authorized Dealer will file a claim, which must subsequently verify the defect. In most cases, the part must be returned to SHARK freight prepaid with the claim. For warranty service on components warranted by other manufacturers, the Authorized Dealer can help you obtain warranty service through these manufacturers’ local authorized service centers. LIMITATION OF LIABILITY SHARK’S liability for special, incidental, or consequential damages is expressly disclaimed. In no event shall SHARK’S liability exceed the purchase price of the product in question. SHARK makes every effort to ensure that all illustrations and specifications are correct, however, these do not imply a warranty that the product is merchantable or fit for a particular purpose, or that the product will actually conform to the illustrations and specifications. THE WARRANTY CONTAINED HEREIN IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representation or promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of SHARK products conforms to local codes. While SHARK attempts to assure that its products meet national codes, it cannot be responsible for how the customer chooses to use or install the product. SHARK PRESSURE WASHERS 1-800-771-1881 www.shark-pw.com SHARK BR • 97-723 • REV. 8/05a PRESSURE WASHER WARRANTY BR PRESSURE WASHER Form #97-723 • Revised 8/05a • Printed in U.S.A.