Download Shark MV3010 Specifications

www.sharkclean.com
VAC-OR-STEAM™
MV3010
OWNER’S GUIDE
MV3010_40_ENG_IB_120713_2.indd 1
12-07-13 1:36 PM
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK®
VAC-OR-STEAM™, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
WARNING: TO REDUCE THE
RISK OF FIRE, ELECTRIC SHOCK OR INJURY
READ ALL INSTRUCTIONS BEFORE USING
YOUR VAC-OR-STEAM™.
DANGER OF SCALDING.
Please use caution when using the steam
function. The steam emitted from the appliance
is very hot.
1. Use the system only for its intended use.
2. DO NOT use outdoors. Use only on dry,
indoor surfaces.
10.DO NOT handle plug or appliance with wet
hands or operate appliance without shoes.
11. DO NOT pull or carry by power cord, use
power cord as a handle, close a door on the
power cord, or pull the power cord around
sharp edges or corners. Do not run appliance
over cord. Keep power cord away from heated
surfaces.
12.DO NOT unplug by pulling on power cord.
To unplug, grasp the plug not the power cord.
Do not use extension cords or outlets with
inadequate current carrying capacity.
13.DO NOT put any objects into the unit
openings. Do not use the unit if any opening
is blocked; keep free of dust, lint, hair and
anything that may reduce airflow.
14.DO NOT put hands or feet under the
Vac-OR-Steam™. Unit gets very hot and may
burn.
3. DO NOT leave the appliance unattended
when plugged in. Always unplug the power
cord from the electrical outlet when not in use
and before servicing.
15.Use ONLY on flat, horizontal surfaces. Do
not use on walls, counters or windows.
4. DO NOT allow the appliance to be used by
children. Close attention is necessary when
used by or near children, pets or plants.
16.DO NOT use on leather, wax polished
furniture and floors, synthetic fabrics, velvet
or other delicate, steam sensitive materials.
5. DO NOT operate the appliance with a
damaged plug or cord, or if the unit has been
dropped, damaged, left outdoors or dropped
into water. To avoid the risk of electric shock,
do not disassemble or attempt to repair the
appliance on your own. Return the appliance
to EURO-PRO Operating LLC (see warranty)
for examination and repair. Incorrect
re-assembly or repair can cause a risk of
electrical shock or injury to persons when the
appliance is used.
17. DO NOT add cleaning solutions, scented
perfumes, oils or any other chemicals to
the water used in this appliance as this may
damage the unit or make it unsafe for use and
void the warranty. If you live in a hard water
area, we recommend using distilled water in
your Vac-OR-Steam™.
6. Use only as described in this manual.
7. Use only manufacturer’s recommended
accessories and replacement pads.
8. To protect against a risk of electric shock, DO
NOT immerse the appliance into water or any
other liquids.
9. DO NOT use for space heating purposes.
2
18. When in use, NEVER turn the appliance over
or on its side. NEVER DIRECT STEAM
TOWARDS PEOPLE, ANIMALS OR
PLANTS.
19.NEVER LEAVE THE CLEANING UNIT
IN ONE SPOT ON ANY SURFACE FOR
ANY PERIOD OF TIME WHEN MULTIPURPOSE PAD IS ATTACHED.
20.Carefully remove the multi-purpose pad
immediately after you have unplugged and
allowed the appliance to cool.
TOLL FREE: 1-800-798-7398
MV3010_40_ENG_IB_120713_2.indd 2
12-07-13 1:36 PM
21. When cleaning the appliance, unplug the
power cord from the electrical outlet and
clean with a dry or damp cloth. Do not pour
water or use alcohol, benzene or paint thinner
on the unit.
22.Extreme caution should be exercised when
using this appliance to clean stairs.
23.Never use the steam function without the
multi-purpose pad attached.
24.Keep your work area well lit.
25.Store appliance indoors in a cool, dry place.
26.To avoid circuit overload, do not operate
another appliance on the same socket (circuit)
as the cleaning unit.
27. If an extension cord is absolutely necessary,
an extension cord rated a minimum of 15
ampere, 14 gage cord should be used. Cords
rated for less amperage may overheat. Care
should be taken to arrange cord so that it
cannot be pulled or tripped over.
36.DO NOT pick up hard or sharp objects such
as glass, nails, screws or coins that could
damage the cleaning unit.
37.DO NOT place appliance on unstable
surfaces such as chairs or tables.
38.DO NOT allow the cleaning unit to be used
as a toy.
39.Close attention is necessary when used near
children.
40.Keep hair, loose clothing, fingers and all parts
of the body away from openings and moving
parts.
41. Turn off all controls before plugging or
unplugging your Vac-OR-Steam™.
WARNING: Your appliance is designed to
POLARIZED PLUG
TO REDUCE THE RISK OF ELECTRIC
SHOCK, this appliance has a polarized
plug (one blade is wider than the other).
As a safety feature, this plug will fit into a
polarized outlet only one way. If the plug
does not fit fully into the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician. DO NOT
ATTEMPT TO DEFEAT
THIS SAFETY FEATURE.
28.DO NOT store unit with damp/wet multipurpose cleaning pad attached.
29.DO NOT use the vacuum function without
dust cup and filter in place.
30. DO NOT vacuum up any liquids.
31.DO NOT pick up anything that is burning or
smoking such as cigarettes, matches or hot
ashes.
32.To reduce the risk of fire DO NOT use to pick
up flammable or combustible liquids such
as gasoline or use vacuum in areas where
flammable or combustible fumes may be
present.
33.DO NOT pick up toxic solutions such as
chlorine bleach, ammonia or drain cleaner
with the cleaning unit.
34.DO NOT use in an enclosed space where
vapors are present from paint, paint thinner,
mothproofing substances, flammable dust or
other explosive or toxic materials.
35.DO NOT run the cleaning unit over largesized objects.
clean non-carpeted, sealed hard floor surfaces
that will withstand high heat. Do not use on
unsealed wood or unglazed ceramic floors,
on surfaces that have been treated with wax
or on some no wax floors. The sheen may
be removed by the heat and steam action. It
is always recommended to test an isolated
area of the surface to be cleaned before
proceeding. We also recommend that you
check the use and care instructions provided
by the floor manufacturer.
SAVE THESE
INSTRUCTIONS
www.sharkclean.com
MV3010_40_ENG_IB_120713_2.indd 3
3
12-07-13 1:36 PM
Steam Technology
Thank you for purchasing the
Shark® Vac-OR-Steam™, the
complete bare floor and carpet
cleaning system.
The unique steam technology, turns simple
tap water into super-heated steam that
infuses the multi-purpose pads for chemical
free cleaning. Only this method creates and
delivers 212°F steam that is effective enough
to clean and sanitize all your hard floor
surfaces. The Shark® Vac-OR-Steam™ can
help you achieve a truly clean and healthy
environment for you and your family.
THIS BOOK COVERS MODEL NUMBER:
MV3010 40
TECHNICAL SPECIFICATIONS
4
Voltage:
120V., 60Hz.
Power:
1200 Watts
Water
Capacity: 500 ml (16.9 oz.)
TOLL FREE: 1-800-798-7398
MV3010_40_ENG_IB_120713_2.indd 4
12-07-13 1:36 PM
Contents
Getting Started: Assembly................................................................2
Vacuum Mode: Assembly.................................................................3
Vacuum Mode..................................................................................4
Vacuum Mode: Storage....................................................................7
Steam Mode: Assembly....................................................................8
Steam Mode.....................................................................................9
Steam Mode: Storage.......................................................................11
Troubleshooting Guide.....................................................................12
Warranty and Registration...............................................................15
www.sharkclean.com
MV3010_40_ENG_IB_120713_2.indd 1
1
12-07-13 1:36 PM
Getting Started
The Vac-OR-Steam™ has two operating modes:
VACUUM MODE:
When assembling your Vac-OR-Steam™ there may
be a little water in or around the water tank of the
steam nozzle. This is because we quality test all our
Shark® products before distributing them, so you
get a quality Shark® Vac-OR-Steam™.
a
d
c
e
f
b
STEAM MODE:
g
h
a Mop Handle
b Main Body with Dust Cup
cScrew
d Vacuum Nozzle
e Steam Nozzle
f Crevice/Brush Combo Tool
g Filling Flask
h Multi-Purpose Steam Pads (x2)
2
TOLL FREE: 1-800-798-7398
MV3010_40_ENG_IB_120713_2.indd 2
12-07-13 1:36 PM
Vacuum Mode: Assembly
a
Fig. 1
Fig. 2
Fig. 3
Fig. 4
ASSEMBLY
1 Insert the handle into the body. Use a
screwdriver (not included) to secure the handle
assembly in place with the screw provided.
(Fig. 1)
1 Place the main unit on top of the vacuum nozzle
and press down to make sure that the vacuum
nozzle is firmly secure to the vacuum body.
(Fig. 2) You will hear an audible click when the
two parts are attached correctly.
ATTACHING THE VACUUM NOZZLE
2 Place the crevice/brush combo tool on the tool
holder on the main body of the unit. (Fig. 3)
3 Wrap the power cord around the cord holders
and secure the plug to the cord (a). (Fig. 4)
www.sharkclean.com
MV3010_40_ENG_IB_120713_2.indd 3
3
12-07-13 1:36 PM
Vacuum Mode
Fig. 9
Fig. 5
Fig. 8
Fig. 6
Carpet
Fig. 7
Bare floor
Fig. 10
USING VACUUM MODE
1 When the vacuum nozzle head is firmly in place,
twist the quick release cord holder to unwrap
the power cord completely. Plug in the unit. The
carpet light (on the left hand side of the floor
nozzle when standing behind the unit) will begin
to blink blue. (Fig. 5) The vacuum is in standby
mode.
2 To begin vacuuming, step on the foot pedal and
the carpet light on the vacuum nozzle will be
solid blue. (Fig. 6) Place your foot lightly on the
top of the vacuum nozzle and tilt the handle
back to begin vacuuming.
To switch to vacuuming in bare floor mode, step
on the pedal once more. The bare floor light will
now be solid blue. (Fig. 7)
To return to standby mode, step on the pedal
once more.
NOTE: If the unit is jammed both bare floor
and carpet lights will begin to blink blue. Please
reference the troubleshooting guide for more
information.
QUICK TIP: The vacuum can be switched
from carpet to bare floor mode while actively
vacuuming or while the unit is at rest. Switching
to bare floor mode will disengage the brush roll.
4
USING THE ACCESSORIES
To use the crevice tool or the dusting brush:
1 Remove the accessory hose from the back of the
unit by turning the hose to the left or right to
unlock. (Fig. 8)
2 Insert the crevice/brush combo tool onto the end
of the hose. (Fig. 9) To use it as a crevice tool,
press the latch on the crevice nozzle and slide
the brush down to expose the crevice nozzle.
3 To replace the accessory hose back into the
vacuum, remove the accessories and insert the
hose into the back of the vacuum. Push down to
lock. (Fig. 10)
TOLL FREE: 1-800-798-7398
MV3010_40_ENG_IB_120713_2.indd 4
12-07-13 1:36 PM
For best results empty the Dust Cup after
each use; empty several times during
prolonged usage or when it reaches the
MAX fill line.
CAUTION:
Unplug the vacuum;
failure to do so might
result in electric
shock.
NEVER OVER-FILL THE DUST CUP.
Always unplug the vacuum from
the electrical outlet before removing and
emptying the dust cup.
Dust Cup
Release
Fig. 13
Fig. 11
Fig. 12
Fig. 14
EMPTYING THE DUST SCREEN
1 Press the dust cup release button on the top
of the unit. Pull the dust cup out of the unit by
pulling forward on the handle. (Fig. 11)
EMPTYING THE DUST CUP
Over time the debris may gather in the dust
screen of your Vac-OR-Steam™. Clean the dust
screen often for optimal suction performance.
2 Hold the dust cup over a trash receptacle and
press the button at the bottom of the dust cup to
empty the dust cup. (Fig. 12)
1 To clean the dust screen, press the top dust cup
lid latch to access the dust screen and remove
built-up debris as required. (Fig. 13, Fig. 14)
3 Close the bottom trap door and replace the dust
cup into the unit.
2 Place the dust screen back into the unit and
close the dust cup lid. You will hear an audible
click when the dust cup lid is closed and secure.
4 To replace the dust cup into the unit, gently push
the dust cup assembly down and in. The dust
cup will click into place.
3 To replace the dust cup into the unit, gently push
the dust cup assembly down and in. The dust
cup will click into place.
www.sharkclean.com
MV3010_40_ENG_IB_120713_2.indd 5
5
12-07-13 1:36 PM
Vacuum Mode - cont.
COMPONENT
MAINTENANCE SCHEDULE
1 Dust Cup
Empty each time you vacuum.
2 Pre-Motor Foam Filters
Rinse and air dry every month under normal use.
3 Post-Motor HEPA Filter
Clean once every 12 months under normal use.
NOTE: The material in the filters will discolor over time. This is NORMAL and will not affect the performance of the filters.
DO NOT operate the vacuum without ALL the filters in place.
DO NOT operate the vacuum with WET filters.
Always unplug the vacuum from the electrical outlet before doing any maintenance on the appliance.
Post Motor Filter
Hepa Filter
Pre-Motor Filters
Thick Foam
Thin Foam
Fig. 18
Fig. 17
Fig. 15
Fig. 16
Fig. 19
TO CLEAN THE PRE-MOTOR FILTERS
TO CLEAN THE POST-MOTOR HEPA FILTER
1 Press the dust cup release button on the top
of the unit. Pull the dust cup out of the unit by
pulling forward on the handle.
1 To release the vacuum nozzle, press the top
“nozzle release” button first and then lift up on
the main body. (Fig. 17)
2 Remove the two foam filters from the unit.
(Fig. 15)
2 Lift the HEPA filter out from the vacuum nozzle.
(Fig. 18)
3 Thoroughly rinse the two filters in lukewarm
water. Squeeze out any excess water. (Fig. 16)
Air dry for 24 hours before reusing.
3 Thoroughly rinse the filter in lukewarm water.
(Fig. 19) Air dry for 24 hours before reusing.
DO NOT use a hair dryer or any other forced
hot air to dry the filter.
4 Insert a dry filter set into the unit. The order of
the filters impacts your dust cup performance.
Make sure the thick filter is on the top and the
thin filter is on the bottom.
6
DO NOT use a hair dryer or any other forced
hot air to dry the filter.
4 Once it is thoroughly dry, replace the HEPA filter
into the vacuum nozzle.
NOTE: Any other servicing should be performed
by an authorized service representative.
TOLL FREE: 1-800-798-7398
MV3010_40_ENG_IB_120713_2.indd 6
12-07-13 1:36 PM
Vacuum Mode: Storage
Occasionally the vacuum may become blocked
by a build up of debris and the Blockage
Indicator light will illuminate. It is important
to locate where the blockage is and carefully
remove it without causing damage to yourself,
the unit or anything else. Perform the
following steps to try to find the blockage.
Beware of sharp objects when clearing blockages.
Damages caused while clearing or attempting to clear
blockages are not covered under your product’s limited
warranty.
Replace parts securely before using again.
Fig. 22
Blockages may cause your vacuum to overheat and
shut down. If so, clear the blockages, then follow the
instructions for Resetting the Motor Thermostat.
Air Intake
Fig. 23
Fig. 21
Fig. 20
1 Tilt the cleaning unit back into upright position.
2 Tap the foot pedal until the unit returns to standby
mode. The carpet light (on the left hand side of the
nozzle) should be blinking blue. (Fig. 22)
CHECKING FOR BLOCKAGES
3 Unplug the unit.
Dust Cup Air Duct:
4 Wrap cord around cord holders and secure plug. Store
cleaning unit in an upright position. (Fig. 23)
1
Remove Dust Cup Assembly and empty Dust Cup
if necessary.
2
Check Air Duct behind Dust Cup for clogs; clear
before replacing Dust Cup Assembly. (Fig. 20)
TO RESET THE MOTOR THERMOSTAT:
CLEANING THE VACUUM NOZZLE:
1
Step on the foot pedal until it goes to standby mode.
T he rotating brush in the vacuum nozzle
must be free of debris for effective cleaning
and maximum suction.
2
Unplug the vacuum.
1
Disconnect the vacuum nozzle and turn it
over to inspect the bottom. If a build-up of
debris is wound around the rotating brush,
remove by carefully cutting with scissors.
Avoid damaging or cutting the bristles.
(Fig. 21)
3
Empty the dust cup and clean filters.
4
Check for blockages in hose, accessories and inlet
openings.
5
Allow the unit to cool for a minimum of 45 minutes.
Note: If vacuum still does not start, contact Customer Service
at: 1-800-798-7398.
www.sharkclean.com
MV3010_40_ENG_IB_120713_2.indd 7
7
12-07-13 1:36 PM
Steam Mode: Assembly
Always unplug the vacuum from the electrical
outlet before changing cleaning nozzles.
The Vac-OR-Steam™, is a complete
bare-floor and carpet cleaning
system. The steam nozzle also
sanitizes bare floors.
Do not use chemicals or detergents
in your Vac-OR-Steam™. You only
need water to achieve super-heated,
sanitizing steam.
Fig. 24
Fig. 27
Fig. 25
Fig. 26
CHANGING TO STEAM MODE
1 To release the vacuum nozzle and change to the
steam nozzle, press the top “nozzle release”
button. (Fig. 24) Lift the main body up and the
vacuum nozzle will be released. You may need
to apply gentle pressure to the nozzle head with
your foot to separate the two parts.
ASSEMBLY STEAM MODE
1 Place the main unit on top of the steam nozzle
and press down to make sure that the steam
nozzle is firmly secure to the main body.
(Fig. 25) You will hear an audible click when the
two parts are attached correctly.
IMPORTANT: Steam nozzle head and multipurpose steam pad must be attached to the
cleaning unit in order to use the steam function.
2 Place the multi-purpose steam pad on the floor
and position the steam nozzle over it. (Fig. 26)
IMPORTANT: Make sure the steam nozzle
head is well secured to the main body by lifting
up on the unit before use.
8
Fig. 28
FILLING THE WATER TANK
1 Before use, make sure to fill the water tank. To
fill the water into the steam nozzle head, turn
the water fill cap counterclockwise to open.
(Fig. 27)
2 Use the filling flask and pour water into the
tank. (Fig. 28) Do not overfill. Replace the cap
on the water tank by turning cap clockwise and
tightening.
QUICK TIP: The steam nozzle head can be
filled with water before or after it is attached to
the main body of the unit.
NOTE: If you live in a hard water area, we
recommend using distilled water in your VacOR-Steam™.
AVOIDING DECALCIFICATION YOUR
STEAM MOP
Calcium and mineral deposits can build up
and impact the performance of your Vac-ORSteam™ over time. To extend the life of your
product we recommend that you use distilled
water.
TOLL FREE: 1-800-798-7398
MV3010_40_ENG_IB_120713_2.indd 8
12-07-13 1:36 PM
Steam Mode
Fig. 29
1
2
3
Dust
Fig. 30
Mop
Scrub
USING STEAM MODE
NOTE: You should vacuum your bare floors
before you steam them.
1 Twist the quick release cord holder to unwrap the
power cord completely and plug in the unit. The
LED lights on the steam nozzle will begin to flash
blue in a chasing manner. (Fig. 29)
2 To begin steaming, step gently on the foot pedal
once to enter DUST mode (1). The DUST light on
the until will appear solid blue. DUST setting is
a light steam for a quick dusting and fastest dry
time.
To switch to MOP mode (2), step on the foot
pedal a second time. The MOP mode light will
appear solid blue. MOP setting is for normal,
everyday steam cleaning.
To switch to SCRUB mode (3), step on the foot
pedal a third time. The SCRUB mode light will
appear solid blue. SCRUB setting is for heavy
cleaning.
3 After selecting the preferred mode, place your
foot lightly on the top of the steam nozzle
and tilt the handle back. Begin mopping in a
backward and forward motion. (Fig. 30)
To return to standby mode step on the pedal
again until the LED lights are flashing blue in a
chasing manner.
QUICK TIP: The steam mode (DUST, MOP,
SCRUB) can be switched while actively steaming
or while the unit is at rest.
IMPORTANT: Do not use the mop without
attaching a multi-purpose cleaning pad and
adding water to the tank first. When you are
using the steam nozzle head for the first time, it
might take longer than the 30 seconds to start
steaming. You will not notice any visible
steam until the steam mode is chosen
and the handle is tilted back.
NOTE: Check water level and fill anytime
throughout the cleaning process to maintain
optimal steam.
www.sharkclean.com
MV3010_40_ENG_IB_120713_2.indd 9
9
12-07-13 1:36 PM
Steam Mode - cont.
The Shark® Vac-OR-Steam™ has three unique steam settings so you can use the perfect amount
of steam for the cleaning task at hand. See below for tips on when to use each setting.
Setting
Ideal for These Surfaces
Laminate
DUST
Bamboo
Hardwood
Recommended Usage
Light cleaning and dusting
Loosen and lift light dirt
Sanitize floors
Marble
MOP
Hardwood
Basic, everyday cleaning
Marble
Remove spots and smaller messes
Tile
Clean moderate and heavily-trafficked areas
Stone
Sanitize floors
Tile
SCRUB
Stone
Linoleum
Tough cleaning and removal of stuck-on
messes and stains
Deep clean heavily-trafficked areas
Cut through heavy dirt and grime
Sanitize floors
Carpet
(with Carpet Glider)
10
Freshen area rugs and carpets
TOLL FREE: 1-800-798-7398
MV3010_40_ENG_IB_120713_2.indd 10
12-07-13 1:36 PM
Steam Mode: Storage
Fig. 31
Fig. 33
Fig. 32
STORAGE
1 Tilt the cleaning unit back to the upright
position.
Fig. 34
CARE OF YOUR MULTI-PURPOSE
CLEANING PAD
3 Unplug the unit.
1We recommend washing your cleaning pad
separately from other fabrics to avoid picking up
lint. Only use liquid detergent (no powder
detergent). Do not use any fabric softeners
or bleach. Line dry or dry on a low dryer
setting. (Fig. 33)
4 Press your foot on the tail of the steam pad to
separate the steam pad from the steam nozzle
head by pulling up on the unit.
2If there are loose threads on the cleaning pad
carefully cut the thread with scissors. Do not pull
on them or cut at the base. (Fig. 34)
5 Wrap the cord around cord holders and secure
the plug. (Fig. 32)
IMPORTANT: The cleaning pad may be very
hot from the steam. Use caution when removing.
Let the unit cool for 2-3 minutes.
2 Tap the foot pedal until the unit returns to
standby mode. The LED lights should be blinking
blue in a chasing manner. (Fig. 31)
6 Press the top “nozzle release” button and lift
the main body up and the steam nozzle will be
released. You may need to apply gentle pressure
to the steam nozzle head with your foot to
separate the two parts.
7 Remove the water tank cap and empty the water
tank.
8 Store the cleaning unit in an upright position.
The unit can be stored with a nozzle on it or
separately.
www.sharkclean.com
MV3010_40_ENG_IB_120713_2.indd 11
11
12-07-13 1:36 PM
Troubleshooting Guide
PROBLEM
POSSIBLE REASONS & SOLUTIONS
The Vac-OR-Steam™ will not
turn on.
Your Vac-OR-Steam™should be securely plugged into a 120V AC electrical
outlet only.
Check your fuse or breaker.
Check to make sure the steam or vacuum nozzle is attached correctly.
The Vac-OR-Steam™ will not
make steam.
The Vac-OR-Steam™ leaves
water on the floor.
The Vac-OR-Steam™
is hard to push.
The Vac-OR-Steam™
is not picking up dirt.
Make sure the water tank is filled to the indicated fill line.
Attach Steam Pad and Steam Nozzle to base of the unit.
TILT MOP HANDLE BACK TO GENERATE STEAM.
Check to see if your multi-purpose cleaning pad has absorbed too much
moisture. We recommend you unplug the Vac-OR-Steam™ and replace the
multi-purpose cleaning pad.
Make sure the steam pad is attached correctly.
Wait 30 seconds after choosing the steam setting before mopping, allowing
water to heat to a 212°F sanitizing steam. If the unit is not allowed to heat
properly, some water may be emitted.
Make sure the steam pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. Replace if the pad is too
dirty or wet.
Check filters to see if they need cleaning. Follow instructions for rinsing and
drying the filters before re-inserting back into the unit. (See “Maintenance”
sections for instructions.)
Dust cup may be full. Empty the dust cup.
Check nozzle or the air intake hose for blockages. Clear blockages if required.
Check that no debris has clogged the brushroll on the vacuum nozzle. Follow
instructions in “Cleaning the Vacuum Nozzle” section to clean the brushroll.
The Vac-OR-Steam™ is equipped with a motor protective thermostat. If for
some reason your appliance overheats, the thermostat will automatically turn
the unit off. Should this occur, perform the following steps to restart the motor
thermostat:
1.
Step on the foot pedal until it goes to standby mode.
2.
Unplug the vacuum.
The Vac-OR-Steam™ turns off
on its own.
3.
Empty the dust cup and clean filters. (See “Maintenance” sections for
instructions.)
4.
Check for blockages in hose, accessories and inlet openings. (See
“Checking for Blockages” for instructions.)
5.
Allow the unit to cool for a minimum of 45 minutes.
6.
Plug in the vacuum.
7.
Step on the foot pedal to select the vacuum mode and tilt the vacuum
back to start vacuuming.
12
TOLL FREE: 1-800-798-7398
MV3010_40_ENG_IB_120713_2.indd 12
12-07-13 1:36 PM
Ordering Parts
To order additional parts and accessories, go to
www.sharkclean.com
or call 1-800-798-7398.
PART
PART NO.
Foam & HEPA Filters
XFF3010
Multi-Purpose Steam Pad
P130W3010
Carpet Glider
XCG3010
Wide Mouth Brush
XMT3010
18” Flexible Crevice Tool
X18FL3010
24” Flexible Crevice Tool
X24FL3010
www.sharkclean.com
MV3010_40_ENG_IB_120713_2.indd 13
13
12-07-13 1:36 PM
Notes
14
TOLL FREE: 1-800-798-7398
MV3010_40_ENG_IB_120713_2.indd 14
12-07-13 1:36 PM
EURO-PRO THREE (3) YEARS LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of three (3) years from the date of the original purchase, when utilized
for normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within
the warranty period, return the complete appliance and accessories, freight prepaid. For assistance
with warranty service options or customer support, please call our customer care and product
specialists at , call 1 (800) 798-7398 or visit our website www.sharkclean.com.
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating
LLC will repair or replace it free of charge. Proof of purchase is required and a fee of $19.95 will
apply to cover the cost of return freight. *
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and does
not apply to any unit that has been tampered with or used for commercial purposes. This limited
warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to
faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused
by or resulting from damages from shipping or repairs, service or alterations to the product or
any of its parts, which have been performed by a repair person not authorized by EURO-PRO
Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC warranty if any, is
limited to the specific obligations expressly assumed by it under the terms of the limited warranty.
In no event is EURO-PRO Operating LLC liable for incidental or consequential damages
of any nature whatsoever. Some states/provinces do not permit the exclusion or limitation of
incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to
include proof of purchase date and to attach tag to item before packing with
your name, complete address and phone number with a note giving purchase
information, model number and what you believe is the problem with the item.
We recommend you insure the package (as damage in shipping is not covered
by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the
specifications contained herein are subject to change without notice.
Product Registration
Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark® product within
ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number
along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By
registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the
accompanying instructions.
www.sharkclean.com
MV3010_40_ENG_IB_120713_2.indd 15
15
12-07-13 1:36 PM
Euro-Pro Operating LLC
US:
Newton, MA 02459
CAN:
Ville St-Laurent, QC H4S 1A7
1-800-798-7398
www.sharkclean.com
Copyright © 2012 Euro-Pro Operating LLC
Printed in China
Illustrations may differ from actual product.
MV3010.E.120713.2
MV3010_40_ENG_IB_120713_2.indd 16
12-07-13 1:36 PM