Download ALLIANCE Automaatic washer Specifications

Installation/Operation Supplement
Automatic
Washers
NOTE: This manual is only a
supplement. Refer to
installation/operation manual
for full instructions.
W001C
W001C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.comlaundry.com
Part No. 201071
October 2002
Installation/Operation Supplement
WARNING
For your safety and to reduce the risk of fire or an explosion, do not store or use gasoline or
other flammable vapors and liquids in the vicinity of this or any other appliance.
W022E
IMPORTANT: Read the complete INSTALLATION/OPERATION INSTRUCTIONS before using the
washer.
201071
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Installation/Operation Supplement
Notes
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201071
Installation/Operation Supplement
Table of
Contents
Important Safety Instructions ...........................................................
5
Installation...........................................................................................
Dimensions and Specifications.............................................................
Installing the Washer ............................................................................
Step 1: Remove the Shipping Brace and Shipping Plug..................
Step 2: Wipe Out Inside of Washtub ...............................................
Step 3: Connect Water Inlet Hoses ..................................................
Step 4: Connect Drain Hose to Drain Receptacle ............................
Step 5: Position and Level the Washer ............................................
Step 6: Plug In the Washer...............................................................
Step 7: Add Water to the Washer ....................................................
Step 8: Check Lid Switch ................................................................
Step 9: Check Installation ................................................................
Electrical Requirements........................................................................
Earthing Instructions ........................................................................
Water Supply Requirements .................................................................
7
7
8
8
8
8
9
11
11
11
11
11
12
12
13
Operation.............................................................................................
Operation Instructions ..........................................................................
Step 1: Add Detergent......................................................................
Step 2: Load Laundry.......................................................................
Step 3: Close Lid..............................................................................
Step 4: Set Water Level Selector .....................................................
Step 5: Set Wash/Rinse Temperature Selector ................................
Step 6: Set Timer to Proper Setting .................................................
Step 7: Start Washer.........................................................................
15
15
15
15
15
15
15
16
16
Maintenance ........................................................................................ 17
Reinstallation of Shipping Materials ............................................... 17
© Copyright 2002, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
201071
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Installation/Operation Supplement
Notes
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201071
Installation/Operation Supplement
Important Safety Instructions
(Save These Instructions)
10. Do not tamper with the controls.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
1. Read all instructions before using the washer.
2. Refer to the EARTHING INSTRUCTIONS in
the INSTALLATION manual for the proper
earthing of the washer.
3. Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable
or explosive substances as they give off vapors
that could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power source.
13. Use your washer only for its intended purpose,
washing clothes.
14. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
15. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
earthing must comply with local codes and be
made by licensed personnel when required. Do
not do it yourself unless you know how!
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. THE
GAS IS FLAMMABLE, DO NOT SMOKE OR
USE AN OPEN FLAME DURING THIS TIME.
16. To reduce the risk of fire, clothes which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc. or chemicals
such as in mops and cleaning cloths, must not be
put into the washer. These flammable substances
may cause the fabric to catch on fire by itself.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
18. Keep your washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have your washer checked by a
qualified serviceman.
7. Before the washer is removed from service or
discarded, remove the lid to the washing
compartment.
19. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
8. Do not reach into the washer if the washtub or
agitator is moving.
20. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
9. Do not install or store the washer where it will be
exposed to water and/or weather.
201071
17. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Installation/Operation Supplement
21. Loading door MUST BE CLOSED any time the
washer is to agitate or spin. DO NOT bypass the
loading door switch by permitting the washer to
agitate or spin with the loading door open. A
brake will stop the washtub within seconds if the
loading door is opened during spinning. If the
washtub does not stop when the loading door is
opened, remove the washer from use and call the
service person.
22. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
23. Always follow the fabric care instructions
supplied by the garment manufacturer.
25. DO NOT operate the washer with missing or
broken parts.
26. DO NOT bypass any safety devices.
27. Failure to install, maintain, and/or operate this
machine according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNING and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
Always contact your dealer, distributor, service agent
or the manufacturer about any problems or conditions
you do not understand.
24. Never operate the washer with any guards
and/or panels removed.
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201071
Installation/Operation Supplement
Installation
Dimensions and Specifications
650 mm (25.6 in.)
*925 mm (36.5 in.)
*1092 mm (43 in.)
*737 mm (29 in.)
*1346 mm (53 in.)
711 mm (28 in.)
10.2 mm (0.4 in.)
660 mm (26 in.)
TLW1030N
TLW1030N
*With leveling legs turned into base.
201071
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Installation/Operation Supplement
Installing the Washer
Step 3: Connect Water Inlet Hoses
NOTE: This manual is only a supplement. Refer to
installation/operation manual for full instructions.
Hoses Without Metric Coupling
Step 1: Remove the Shipping Brace and
Shipping Plug
IMPORTANT: The shipping brace and plug should
be saved and must be reinstalled whenever washer
is moved or transported to a new location.
Insert rubber washers in water inlet hose couplings.
Connect inlet hoses to water supply faucets. Turn on the
water supply faucets and flush the lines. Connect hoses
to the hot and cold valve connections at rear of washer.
Hoses With Metric Coupling
Connect the BLACK colored hose coupling end of
the inlet hoses (with filter washers) to the water supply
faucets. Connect the BRASS colored hose coupling end
of hoses (with rubber washers) to the hot and cold water
mixing valve connection at rear of washer.
IMPORTANT: DO NOT cross thread or overtighten
couplings.
1
2
1
WATER
MIXING
VALVE
3
2
TLW872N
TLW521N
1
2
1
2
3
Water Inlet Hoses
Cold Water Connection
Hot Water Connection
Shipping Brace
Shipping Plug
Figure 3
1
1
Figure 1
2
Step 2: Wipe Out Inside of Washtub
W091I
1
2
Rubber Washer (Plain)
Inlet Hose
Figure 4
W371I
Figure 2
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201071
Installation/Operation Supplement
Step 4: Connect Drain Hose to Drain
Receptacle
High Standpipe Installation
2
1
3
2
1
4
TLW875N
TLW875N
1
2
3
4
TLW873N
1
2
Retainer Clamp
Standpipe Adapter
Standpipe Adapter
Drain Hose
Tie-Down Strap
Standpipe (Standpipes higher than 122 cm
[4 ft.] are not recommended)
Figure 5
Figure 7
IMPORTANT: Drain receptacle must be capable of
handling a minimum of 3.2 cm (1-1/4 inch) outside
diameter drain hose.
Low Standpipe Installation
Standpipe Installation
NOTE: No. 562P3 Siphon Break Kit is required for
this type of installation (available at extra cost).
2
1
30.48 cm
(12 in.)
1
91.44 cm (36 in.)
RECOMMENDED
HEIGHT
4
2
3
TLW874N
1
2
3
4
Ribbed Portion of Drain Hose
Standpipe Adapter
Tie-Down Strap
Standpipe 5.08 cm (2 in.) or 4 cm (1-1/2 in.)
Diameter
Figure 6
201071
3
TLW876N
1
2
3
562P3 Siphon Break Kit
Drain Hose
Standpipe
Figure 8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Installation/Operation Supplement
Sink Installation
Laundry Tub Installation
3
2
1
1
TLW878N
TLW878N
1
Tie-Down Strap (Tape if necessary)
Figure 11
TLW877N
1
2
3
Drain Hose
Tie-Down Strap or Wire Tie
Cabinet Top Hinge
Figure 9
In-the-Wall Installation
1
2
W514I
W514I
1
2
Tie-Down Strap (Tape if necessary)
Standpipe Adapter
Figure 10
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201071
Installation/Operation Supplement
Step 5: Position and Level the Washer
Step 7: Add Water to the Washer
3
2
1
W391I
4
W391I
Figure 14
5
W179I
W179I
1
2
3
4
5
Step 8: Check Lid Switch
Rubber Foot
Washer Base
Level
Locknut
Leveling Leg
Figure 12
Step 6: Plug In the Washer
W376IE0C
Figure 15
Step 9: Check Installation
W422I
W422I
Figure 13
201071
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Installation/Operation Supplement
Electrical Requirements
Earthing Instructions
230 Volt/50 Hertz
The washer must be earthed. In the event of malfunction
or breakdown, earthing will reduce the risk of electric
shock by providing a path of least resistance for
electric current. The washer is equipped with a cord
having an equipment-earthing conductor and a threeprong earthing plug. The plug must be plugged into an
appropriate outlet that is properly installed and earthed
in accordance with all local codes and ordinances.
NOTE: This manual is only a supplement. Refer to
installation/operation manual for full instructions.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death, all wiring and
grounding MUST abide with local
electrical codes. It is the customer’s
responsibility to have the wiring and
fuses checked by a qualified electrician to
make sure the laundry room has adequate
electrical power to operate the washer.
W244
WARNING
Improper connection of the equipmentearthing conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the washer is
properly earthed.
W032
WARNING
To reduce the risk of electric shock or fire,
DO NOT use an extension cord or an
adapter to connect the washer to the
electrical power source.
Do not modify the plug provided with the washer – if
it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
WARNING
W031
The washer is designed to be operated on a separate
polarized three-wire, earthed 230 Volt, 50 Hertz,
single-phase electrical circuit and must abide by local
electrical codes.
12
Any disassembly requiring the use of
tools must be performed by a suitably
qualified service person.
W299
NOTE: Electrical receptacle must be located so
that it is easily accessible with machine in place. If
machine is hard wired, an intermediate shut-off
box with a 3 mm gap is required (335-1 [22.2]
[24.3]).
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201071
Installation/Operation Supplement
Water Supply Requirements
1
NOTE: This manual is only a supplement. Refer to
installation/operation manual for full instructions.
2
WATER
MIXING
VALVE
WARNING
Under certain conditions, hydrogen gas
may be produced in a hot water system
that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If
the hot water system has not been used
for such a period and before using the
washer, turn on all hot water faucets and
let the water flow from each for several
minutes. This will release any
accumulated hydrogen gas. The gas is
flammable. Do not smoke or use an open
flame during this time.
W029
C
H
3
4
TLW879N
1
2
3
4
Water Supply Faucets
Cold Water Connection
Hot Water Connection
Water Inlet Hoses
Figure 16
Washer needs two standard 19.1 mm (3/4 inch) water
supply faucets with a pressure between 1.4 and 8.3 bar
(20-120 pounds per square inch).
201071
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Installation/Operation Supplement
Notes
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201071
Installation/Operation Supplement
Operation
Operation Instructions
Step 3: Close Lid
NOTE: This manual is only a supplement. Refer to
installation/operation manual for full instructions.
Step 1: Add Detergent
W318IE0C
Figure 19
Step 4: Set Water Level Selector
CPW70
CPW69
LOWEST WATER FILL
HIGHEST WATER FILL
W395I
Figure 17
Step 2: Load Laundry
CPW189
CPW189
Load dry clothes loosely into washtub – DO NOT
overload! (7 kg maximum dry clothes load.)
Figure 20
Step 5: Set Wash/Rinse Temperature
Selector
HOT WASH/
COLD RINSE
CPW71
WARM WASH/
COLD RINSE
CPW72
W392I
COLD WASH/
COLD RINSE
CPW73
Figure 18
CPW173
CPW173
Figure 21
201071
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Installation/Operation Supplement
Step 6: Set Timer to Proper Setting
Step 7: Start Washer
Pull the timer knob to start water fill. Agitation will
begin when the water level reaches the level selected.
PULL KNOB TO START – PUSH TO STOP
CPW82
Figure 24
CPW88
Figure 22
REGULAR CYCLE
CPW60
PERMANENT PRESS
CYCLE
CPW74
DELICATE CYCLE
CPW62
WASH
CPW63
RINSE
CPW64
SPIN
CPW65
END OF CYCLE (OFF)
Figure 23
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
201071
Installation/Operation Supplement
Maintenance
NOTE: This manual is only a supplement. Refer to
installation/operation manual for full instructions.
Reinstallation of Shipping Materials
Shipping Brace
Open the washer lid and place the brace over the
washer agitator, placing the back of the brace into the
lid opening first.
1
Shipping Plug
The plug fits into two openings: the base opening and
the shipping plug opening on the bottom of the
movable pivot dome. The plug MUST be inserted into
both openings to prevent damage to the washer. Refer
to Figure 25.
2
3
W544I
1
2
3
Shipping Plug Opening
Base Opening
Shipping Plug
Figure 25
201071
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17