Download Clarion VRX938R Owner`s manual
Transcript
English VRX938R Installation and Wire connection manual 1. 2. 3. 4. 5. 6. 7. 8. 9. BEFORE STARTING ............................................................... PACKAGE CONTENTS ........................................................... GENERAL CAUTIONS ............................................................ CAUTIONS ON INSTALLATION .............................................. INSTALLING THE MAIN UNIT ................................................. REMOVING THE MAIN UNIT .................................................. CAUTIONS ON WIRING .......................................................... WIRE CONNECTION .............................................................. SAMPLE SYSTEMS ................................................................ 57 57 58 58 59 61 61 62 65 1. BEFORE STARTING 1. This set is exclusively for use in cars with a negative ground 12 V power supply. 2. Read these instructions carefully. 3. Be sure to disconnect the battery “v” terminal before starting. This is to prevent short circuits during installation. (Figure 1) Car battery Figure 1 2. PACKAGE CONTENTS 1 Main unit 2 Tuner Amp unit 3 Manuals Owner’s manual & Installation manual Warranty card 4 Power supply lead (For the tuner amp unit) 5 Connection cord (Main unit ↔ Tuner amp unit) 6 Antenna extension cord 7 Bag for accessories of the main unit (No. 1) Flat head screw (M5 × 8) ............................ 4 Sems hexagonal bolt (M5× 8) ..................... 5 Electro tap Machine screw (M4× 3) ............................... 4 8 Bag for accessories of the main unit (No. 2) Hook plate ................................................... 2 Cord clamp Spacer Special screw 9 Bag for accessories of tuner amp unit Maunting bracket ......................................... 2 Canoe clip ................................................... 4 Machine screw (M4 × 8) .............................. 4 0 Universal mounting bracket ! Remote control unit @ Battery (for remote control unit) # Outer Escutcheon $ DCP Case VRX938R 57 Installation and Wire connection manual ■ Contents English 3. GENERAL CAUTIONS Installation and Wire connection manual 1. Do not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION service centre. 2. Use a soft, dry cloth to clean the case. Never use a rough cloth, thinner, benzine, or alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gently. 4. CAUTIONS ON INSTALLATION 1. Prepare all articles necessary for installing the main unit before starting. 2. This model is used with the LCD panel slid forwards (shell loading system). On some types of cars, the LCD panel may touch the dashboard or shift lever, in which case it cannot be installed. Check that the set will not hamper operation of the shift lever before choosing the place of installation.(Figure 2) 5. Use the enclosed screws for installation. Using other screws can cause damage. (Figure 4) Chassis Chassis Damage Max. 8 mm Dashboard Figure 4 6. The source unit has mounting screw holes for NISSAN (N marks) and TOYOTA (T marks) vehicles. T Shift lever (check that it does not touch the LCD.) N T Shift lever Figure 2 3. Install the unit within 30° of the horizontal plane. (Figure 3) N T Figure 5 Max. 30˚ Figure 3 4. If you have to do any work on the car body, such as drilling holes, consult your car dealer beforehand. 58 VRX938R N English 5. INSTALLING THE MAIN UNIT ■ Universal Mount Notes: 1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. 2) Fasten the front stopper securely to prevent the main unit from coming loose. • Console opening dimensions Rear fastening hole (of vehicle) 182 mm Instrument panel 53 mm Hole Hole Stoppers Screwdriver Rubber cap Main unit Universal mounting bracket Stoppers 2-Spring Outer escutcheon Note: Set the outer escutcheon so that its metallic part on the back side fits the upper edge of the main unit. Figure 6 VRX938R 59 Installation and Wire connection manual 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6. 2. Wire as shown in Section 8. 3. Insert the main unit into the universal mounting bracket until it locks. 4. Mount the outer escutcheon so that all the hooks are locked. ■ Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) English Installation and Wire connection manual This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and screws marked (∗). (Figure 8) If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install the main unit in the following procedure. 1. Remove the screws from both side of the main unit. Then, at either side, lift the leaf spring until the engaging claws are released from the holes, and slide the spring to the direction of arrow to remove it. Repeat the same for the other side to remove the springs from the both sides. (Figure 7) 2. Secure the mounting brackets to the chassis as shown in Figure 8. Holes are pre-tapped for TOYOTA and NISSAN vehicles; modification, such as drilling new holes, of the mounting brackets may be required for other models. 3. Wire as shown in Section 8. 4. Secure the unit in the dashboard, and then reassemble the dashboard and the centre panel. 2-Screw Engagin claw Main Unit 2-Spring Screwdriver Figure 7 4-Hexagonal screw ∗ (M5 × 8) Mounting bracket (1 pair for the left and right sides) Main Unit Pocket Note 2 Centre Panel (Note 1) ∗: The screws with this mark are enclosed in this set. ★: The parts and screws with this mark are used to install radio or included in the installation kit. Figure 8 Note 1: In some cases, the centre panel may require some modification (trimming, filling, etc.). 60 VRX938R Note 2: If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool. the main unit out by the hook plate. (Insert both the right and left edges of the hook plate.) (Figure 9) Note: Keep the hook plate. You cannot remove the main unit without disengaging the hook plate. Instrument panel Universal mounting bracket 2-Hook plate Main Unit Spring Outer escutcheon A B Figure 9 7. CAUTIONS ON WIRING 1. Be sure to turn the power off before wiring. 2. Be particularly careful where you route the wires. Keep them well away from the engine, and exhaust pipe, etc. Heat may damage the wires. 3. If the fuse should blow, check to see if the wiring is correct. If it is, replace the fuse with a new one with the same amperage rating as the original. 4. When any fuse is to be replaced, pull out the fuse (15A) at the rear of the tuner amp unit and put in a new one (Fig.10). Rear view of the tuner amp unit Fuse (15A) Figure 10 CAUTION Fuse After the connection, fix the lead by a clamp or insulation tape for protection. 5. To replace the fuse, release the catch on the main unit side, remove the old fuse and insert the new one. (Figure 11) Note: There are various types of fuse holder. Do not let the battery side touch other metal parts. Fuse holder Figure 11 VRX938R 61 Installation and Wire connection manual 1. When the rear of the main unit has been secured with the method shown in Figure 6 unfasten the special screw. 2. Remove the outer escutcheon. 3. Insert the hook plate between the spring and the universal mounting bracket, fit tab B of the spring into hole A of the hook plate, then pull English 6. REMOVING THE MAIN UNIT English 8. WIRE CONNECTION 2 Installation and Wire connection manual Securely connect to the metal part of the car with a screw, etc. Black Yellow Earth (ground) cord Choke coil Main power supply cord 3A Fuse CeNET cable (provided with this unit) CeNET cable (Sold separately) Subwoofer output terminal L+R (RCA) Power supply lead Front audio output (input) terminal L+R (RCA) ∗6 5 Rear audio output (input) terminal L+R (RCA) ∗6 Reset switch DSP select switch (∗5) Tuner amp unit ∗1 Top view of the tuner amp unit 4 ∗4 1 ∗9 3 ∗8 VISUAL input (RCA)/TV TUNER input (RCA) DVD DECK / DVD Changer input (RCA) ∗10 VISUAL audio input terminal L+R (RCA) VIDEO output (RCA) ∗7 62 VRX938R B-3 B-5 B-4 B-1 English B-2 B-6 Installation and Wire connection manual 9 B-7 B-8 A-7 ∗1 A-8 ∗3 7 A-4 A-6 No. 0 ∗2 ∗2 8 B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 A-4 A-5 A-6 A-7 A-8 1 2 3 4 5 6 7 8 9 0 6 A-5 Description REAR RIGHTB REAR RIGHTv FRONT RIGHTB FRONT RIGHTv FRONT LEFTB FRONT LEFTv REAR LEFTB REAR LEFTv +12 V MAIN POWER (∗2) AUTO ANTENNA (∗1) ILLUMINATION +12 V ACCESSORY (∗2) GROUND NAVI terminal RGB INPUT CCD/VISUAL 2 terminal Radio antenna jack (∗4) CeNET terminal Spare terminal (Black) Phone mute (Brown) (∗3) Spare terminal (Yellow) ISO CONNECTOR Parking brake (Bright Green) ∗1: When the unit is installed in a 1998 or later Volkswagen model, make sure to interrupt the <<Remote>> output. Disconnect the <<blue/white>> wire and insulate the front ends of this lead. A breakdown may occur if the lead is not disconnected, or front ends are not insulated. ∗2: In certain vehicles - Volkswagen/Opel/Vauxhall - it is necessary to exchange the accessory <<Red>> and the main power <<Yellow>> connection, to avoid overload and loss of memory. ∗3: Connecting the PHONE MUTE Terminal The lead included with the unit must be connected to the specified position of the vehicle’s ISO connector in order to use the “triggered audio mute for cellular telephones” function. ∗4: Use the attached extension lead when necessary. (Provided with this unit) Note: Before making any installation, disconnect the car battery - (negative) cable. ∗5: When a DSP (sold separately) is connected and the internal amp of the Tuner Amp Unit is used, set the normal DSP select switch to “D”. Then, the AUDIO OUT (IN) terminal of the Tuner Amp Unit is only available for audio input, not outputting the audio. N D ∗6: Connect to a separately sold amp, DSP, etc. with a separately sold RCA cord (L,R). ∗7: Connect to a separately sold Rear view monitor. ∗8: Connect to separately sold VTR equipment or security (CCD) camera. ∗9: Connect to a separately sold navigation device. ∗10: DVD DECK and DVD changer can not be connected at the same time. VRX938R 63 English ■ Connecting the Accessories • Connection to the external amplifier The external amplifier cannot be connected unless the DSP is connected. For detailed information, refer to the instruction manual of the DSP. Installation and Wire connection manual • Connection to the CCD camera for vehicle The CCD camera for vehicle can be connected to the system expansion terminal on the main unit. For detailed information, refer to the instruction sheet or manual for the CCD camera. Notes: • A power supply box (sold separately) is required for connection of the main unit and the CCD camera. • While the CCD camera is used, the navigation cannot be turned on. • The power supply box for camera CCA147 cannot be used. Please use the CCA188 instead. • If the specified lead of the cellular phone is connected to the phone mute lead of the source unit, the audio mute is available when the cellular telephone is used. For audio mute setting in cellular telephone use, see page 43. • DAB (Digital Audio Broadcasting) When the DAB is to be connected, use the CeNET connector. For detailed information, refer to the instruction manual of the DAB. For DAB connection, the DAH913 can only be connected. The DAH9500Z cannot be connected. • TV Tunner When the TV TUNER is to be connected, connect the CeNET connector and RCA PIN (yellow). For detailed information, refer to the instruction manual of the TV TUNER. ■ Connecting the parking brake lead Parking brake lamp + lead to battery Connect the lead to parking brake lamp earth in the meter panel. Notes: • Connecting the parking brake lead to lamp earth allows you to watch TV/VTR/DVD VIDEO/DVD Changer when the parking brake is engaged. • When the parking brake lead is not connected, the monitor will stay off. - cord parking brake signal lead Connect these three leads. Parking brake lead (bright green) Parking brake 64 VRX938R English 9. SAMPLE SYSTEMS ■ Sample System 1 Installation and Wire connection manual GPS ANT. MAIN UNIT VRX938R RGB Front/Rear Speaker MINI DIN (8P) ∗ When a video composite source is used, connect it to the 8pin Mini-DIN video jack. When a RGB source is used, connect it to the 8-pin DIN RGB jack. In case a CLARION navigation system is used, connect it to both input. ∗ To enable the correct input, it is necessary to configure the VRX938R as described on page 41. COMPOSITE (RCA) CeNET ∗ AMP built-in COMPOSITE (RCA) NAX9500E Rear view monitor TV ANT. DAH923 (DAB TUNER) TTX7503z TTX7502z (CeNET TV TUNER) ∗DAH 9500Z cannot be connected. CeNET DCZ628 COMPOSITE (RCA) RDI OUT CeNET DAB ANT. CCA-519-500 (CD CHANGER) ∗ When two CD changers or DVD changers are connected, CCA-519-500 is required. VCZ628 (DVD CHANGER) Set the [CENET/STAND ALONE] switch to the [CeNET] position. CeNET STAND ALONE VRX938R 65 English AMP REMOTE ■ Sample System 2 GPS ANT. Installation and Wire connection manual RGB MAIN UNIT VRX938R NAX9500E MINI DIN (8P) ∗ AMP built-in ∗ When a video composite source is used, connect it to the 8-pin Mini-DIN video jack. When a RGB source is used, connect it to the 8-pin DIN RGB jack. In case a CLARION navigation system is used, connect it to both input. ∗ To enable the correct input, it is necessary to configure the VRX938R as described on page 41. COMPOSITE (RCA) COMPOSITE (RCA) CeNET DAB ANT. RDI OUT DAH923 CeNET (DAB TUNER) DCZ628 (CD CHANGER) VCZ628 (DVD CHANGER) Set the [CENET/STAND ALONE] switch to the [CeNET] position. CeNET 66 VRX938R STAND ALONE CCA-519-500 ∗ When two CD changers or DVD changers are connected, CCA-519-500 is required. English TV ANT. Installation and Wire connection manual TTX7503z TTX7502z COMPOSITE (RCA) REAR VIEW MONITOR (CeNET TV TUNER) CCA-389 CeNET OR DPH913 VTR RCA(SUB) RCA(R) RCA(F) (DIGITAL SOUND PROCESSOR) AMP. VRX938R 67 Memo 68 VRX938R