Download Axis 211a Installation guide

AXIS'"
COMMUNICATIONS
Network Camera
I
lnstallation Guide
I
AX1S 210/210A/211/211A
I
I
I
Page 3
AXIS 210/21OA/211/211A Installation Guide
AX1S 210/210A/211/211A
Network Camera lnstallation Guide
This installation guide provides instructions for install ing the AXIS 210/ 21 OA/211/ 211A
Network Camera on your network. For other asp ects of using the product, please see the
AXIS 2 10/2 1OA/ 211/2 11A User's Manual, availabl e on the CD included in this package, or
from www.axis.com
lnstallation steps
Follow these steps to inst all the network camera on your local network (LAN) :
1. Check the package contents against the list below .
2. Connect the network camera. See page 4.
J.
Set an lP address. See page 5 for information on the available methods.
4. Set the password. See page 9.
Package contents
Item
Note s
Network camera
AXIS 210/2 10A/2 11/2 11A
Power adapter
Country-specific
Camera stand
Supplied wit h mounting screws
I/O terminal connector
4-pin I/O termi nal connector - 1 tr ansistor output , 1 digi tal input, auxi liary power and GND
CD
Install ation tool and other soft ware, product documentation
Printed materials
•
AXIS 210/210A/211/211A Installa t ion Guide (this document)
•
Axis Warranty Document
Overview
AX1S 21 O/AX1S 21 OA
AX1S 211/AX1S 211A
Tele/wi de pull er
Sta tus
indica tor
Focus pull er
DC-I ris
I
Page 4
AXIS 2 10/ 21OA/2 11/211A Installation Guide
Underside
Rear panel AX1S 21 O/AXIS 211
~~-0
I
"'::I
DC- Iris control
(AXIS 211)\
Internal
cab"le~~;:;~~~~~~;;;~=::::::::....
"'"
microphone
(AXIS 210A
AXIS 211A)
Serial number
",,* ,., L' ~
1111111111111 1'1 111111111
:=::=:::::-: c ((
=-----
'~"
IS!!
Network connector
(and PoE for AXIS 21 1)
,' .Ji" Control button
I
__ I
1[9
~ --- Power indicator
b
0'
~ Netwo rk
indicator
Rear panel AX1S 210A/AX1S 211A
DC-Iris control cable
(AXIS 211A)
Audio
output
Network connector (and PoE)
Connections
1.
Connect the network camera to your network using a standard network cable.
2. Connect power, using one of the 3 supported methods listed below:
• The supplied power adapter.
• PoE (Power over Ethernet) via the network cable (AXIS 21OA/AXIS 211/AXIS 211A). This will
automatically be detected if available via the network.
• The I/O terminal connector on the rear panel.
Important!
To use the network camera outdoors it must be installed in an 9_uJdoor enclosure. For more information on
outdoor enclosures, please visit www.axis.com
(
AXIS 210/21 OA/211/21 1A Insta llat ion Guide
Page 5 )
Setting the lP address
The AXIS 210/210A/211/211A is designed for use on an Ethernet network and must be
assigned an IP address to make it accessible.
AX1S lP Utility
AXIS IP Utility is the recommended method for setting an IP address in Windows. This free application can
be used on networks with or without a DHCP server. See page 6 for more information .
All installation methods
This table shows all of the available methods for setting or discovering the IP address. Select a
method from the left-hand column and check the requirements for it to the right.
~
DHCP Server in
network
Install on same
network segment
AXIS IP Utility
(recommended method)
See page 6
Optional
Required
Windows
UPnP"'
See page 7
Optional
Required
Windows
(ME or XP)
Required
All
Installation
methods
!
-
ARP/Ping
See page 7
AXIS Dynamic DNS Service
See page 8
Recommended
View DHCP server
admin pages for IP address
(See note below)
Required
Not es: •
Internet connection
with no HTTP proxy
Required
Operating
system
All
All
UPnP"' and DHCP are both enabled by default in the AXIS 210/21OA!21 1/21 1A.
• The AXIS 21O/21OA/21 1/21 1A has the default IP address 192.168.0.90
• To view the admin pages for the DHCP server, please see the server's own documentation. You may need to
contact your network administrator.
• If setting the IP address fails , check that there is no firewall blocking the operation.
I
Page 6
AXIS 210/21 OA/211 /211 A Installation Guide
AX1S lP Utility
2erver
AXIS IP Utility is a free Windows
application that discovers and displays
Axis devices on your network.
The application can also be used to
manually set a static IP address.
Note that you must install the network
camera on the same network segment
(physical subnet] as the computer
runnin g AXIS IP Utility.
IP
tfJ
~iew
tjelp
I :;J! ~
I
Name
lIP address
I 5erieJnumber
10,93 ,141.165
10,93 ,141.208
AXIS 206W ' 6815E8
AXIS 20ri~1 - 682803
AXIS 213 - 6':,'~B8 E
AXIS 210 - 657098
AXIS 2 10 - 65889 9
AXIS 2 11 - 6538AD
AXI S 2 11 • 18201A
AXIS 210 - 656 D94
AXIS 211 - 658 46A
10,93,142, 13
10,9 3, 141.167
10,93, 137,60
10,9 3, 135,54
10.93 .140,211
AXIS 221 · 181E67
10.93 .13 0.141
10 .93.13 7.208
10.93. 127 .222
-I
Workstation interface 1 (10.93 .130 .1)
AXIS IP Utility is available on the CD supplied with this product, or it can be downloaded from
www.axis.com/techsup
Automatic discovery
1. Check that the network camera is connected to the network and that power has been
applied.
2. Start AXIS IP Utility. When the network camera appears in the window, double-click it to
open the camera's home page.
3. See page 9 for instructions on how to set the password.
Set the lP address manually
1. Acquire an unused IP address on the same network segment your computer is connected
to.
2. Click the button
r­
(Set IP address using serial number) and enter the serial number and
IP address for the network camera. The serial number (SIN) is located on the camera's
underside label (see page 4).
3. Click the Set IP button and then restart the network camera (within 2 minutes).
4. Click View Home Page to access the network camera's web pages.
5. See page 9 for instructions on how to set the password.
Note:
AXIS IP Utility can be used to change a dynamically set IP address to a static one.
Page 7
AXIS 210/21 OA/211/211 A In t alla tion Guide
UPnpnl
UPnP'" functionality is enabled by default in the AXIS 21O/210A/211/211A. If also enabled on
your computer (Windows ME or XP), the network camera will automatically be detected and a
new icon will be added to "My Network Places." Click thi s icon to access the network camera .
See also page 9 for instructions on how to set the password.
Note:
To inst all the UPnP T~ service on your computer, open the Control Panel from the Start Menu and select
Add/Remove Programs. Select Add/Remove Windows Components and open the Networking Services
sect ion. Click Details and then select UPnP as the service to add.
UPnP' " is a certifi cati on mark o f the UPn P' · lmpl em enters Corpo ra tion.
Manual lnstallation with ARP/Ping
1. Acquire an unused IP address on the same network segment your computer is connected to.
2. Locate the serial number (S/N) on the camera's underside label (see page 4).
3. Open a Command Prompt on your computer. As appropriate for your operating system,
enter the follow ing commands :
Windows syntax :
Win d o ws example:
arp - s <IP Add r e ss > <Se r i a l Number >
pi n g -1 4 0 8 - t <IP Address >
arp - s 192.1 6 8.0.1 25 0 0 - 40 -8c - 1 8-10 - 0 0
pi n g -1 4 0 8 - t 1 92 .1 6 8 . 0 .1 25
UNIX/Linux/Mac syntax:
UNIX/ Linux/Ma c exampl e:
a rp -s <I P Addr ess > <Se r i a l NUlnber > temp
p ing - s 4 0 8 <I P Addres s>
arp -s 1 9 2 .1 6 8 . 0 .1 2 5 0 0 : 4 0: 8c: 1 8 : 1 0 : 0 0 temp
p i ng - s 4 0 8 192 . 168 .0.125
4. Check th at the network cable is connected. Start/resta rt the camera by disconnecting and
reconnecting power, which must be done within 2 minutes of entering the ARP command.
5. Close the Comm and prompt when you see 'Repl y from 192.168.0.125: ...' or similar.
6. Start your browser, type in http ://<lPaddress>intheLocation/Address field and press
Enter on your keyboard.
7. See page 9 for instructions on how to set the password.
Not es: • To open a command
prompt in Windows: from the St art menu, select Run... and ty pe crnd (or comman d in
Wind ows 98/ME). Click OK.
• To use the ARP command on a M ac
as X, use the Termin al uti lity,
wh ich is fo und under App li cat ion > Utilities.
I
Page 8
AXIS 210/210A/211/211A Installation Guide
The AX1S lnternet Dynamic DNS Service
The AXIS Int erne t Dynamic DNS Service is a free service provided by Axis. This se rvice allows
you to quickly and simply install your camera, which then receives a static name (DNS name)
and a dynamic IP address. More information about the AXIS Internet Dynamic DNS Service is
avail able at www.axiscam.net
To perform this procedure, your network should have an Internet connection with no HTrP
proxy, and IP addresses should preferably be assigned v ia DHCP.
Follow these instructions :
1. After making the connections for network and power, wait for the Status indicator on the
front of the camera to show a ste ady green.
2. Press the Control button on the undersid e of th e camera once. The Status indi cator flashes
green while it connects to the AXIS Internet Dynami c DNS Service.
3. Wait for the Status indicator to go back to showing a steady green.
4. To complete the installation, now visit www.axiscam.net from an Internet connected
computer. This must be done within 60 minutes of pressing the Control button.
5. Follow the on-screen instructions provided by the AXIS Internet Dynamic DNS Service.
You will need the product's serial number to complete the installation. See pa ge 4. See also
page 9 for instructions on how to set the password.
Important!
Please note that this procedure will send the IP address, firmware version , product type, serial number and
HTIP port number of the network camera to the AXIS Internet Dynamic DNS Service.
No personal information is transferred.
To remove the DNS name and unregister from this servi ce, open the Setup pages in the
network camera, click System Options> Network> TCP/IP > Basic, click the Settings button
for the AXIS Internet Dynamic DNS Service and fin ally, click the Remove button.
AXIS 210 /21 OA/211 /2 11A Installation Gui de
Setting the Password
1. When accessing the AXIS 21O/21OA/211 /211A for
the first time, the 'Configure Root Password'
dialog will be displayed on the screen.
Page 9
.~ ! s:....
Configure Root Pa sswor d
.........",
.c..~~ ~ III ... d,
Enter a password and then re-enter it, to confirm
the spelling. Click OK.
b., C1.,
­
4·...... '
t_ '.o d.....t". ,.,..·co..
to. ",.d
Th . fIIU' -.q
2.
10•
,,"," •;-;-­
.
f (l f
. dm'..II I . . ...'"
~"'n
._t
""'u " 1-, d'-6~
,t.
If It ,. rI . . .. ".d ro. ...~ It ..
!">I pMdu ~"I: ,.,... . ~ 1'>
• •••• t to ... . f .,-t " . / d.h lt
,,.ttl n9 f , l., j.>. .. . ~.,... butt on ~ . ' . oi ".,!h. ~t1'. 14 00n'il .. I•••• ••• U .
....... '"'.u..., .-r>t.t1Clll'll f . . rno••
mf.'"' ~-..
3. The 'En ter Network Password' dialog will
appear. Enter the User name : root
Note: The default administrator user name root is permanent and cannot be deleted.
4. Enter the password as set in step 2 above, and click OK. If the password is lost, the AXIS
21O/21OA/211/211A must be reset to the factory default settings. See page 10.
5. If required, click Yes to install AMC (AXIS Medi a Control), to allow viewing of the video
stream in your browser. You will need administrator rights on the computer to do this.
6. The Live View page of the AXIS 21O/21OA/211/211A is displayed, complete with links to
the Setup tools, which allow you to customize the camera to your specific needs.
AXI S 21 1A Network Camera
liv e Vie w I SBtlllJ I H AIIJ
"'" Help - Displays on line
help o n all aspect s of
using the ca mera .
\
Setup - Pr ovides all
the necessa ry tools
for se tting up th e
ca mera to
requiremen ts.
Accessing the network camera from the lnternet
Once installed, your network camera is accessible on your local network (LAN). To access the
network camera from the Internet, network routers must be configured to allow incoming
tr affic, which is usually done on a specific port. Please refer to the documentation for your
router for further instructions.
For more information on this and other topics, please visit the Axis Support Web a t
www.axis.com/techsup
I
Page 10
AXiS 210/21 OA/211/211 A Installation Guide
Resetting to the Factory Default Settings
This will reset all parameters, including the IP address, to the Factory Default settings:
1. Disconnect power from the camera.
2. Press and hold the Control button (on the underside of the camera) and reconnect power.
3. Keep the button pressed until the Status Indicator displays yellow (this may take up to 15
seconds], then release the button.
4. When the Status indicator displays green (which can take up to 1 minute) the camera is
reset to the factory default settings.
5. Re-install the network camera using one of the methods described in this document.
Further information
For further information, please see the AXIS 21O/21OA/211/2 1l A User's Manual, which is
available on the CD included in this package. Updated versions can be obtained from
www.axis.com