Download Mytee 1003DX Product manual

Instructions for
1000DX,1000DX-200, 1001DX,
1001DX-200, 1003DX, 1005DX Speedster
Please read before use.
Register your product
at www.mytee.com/help
Model #
1000DX & 1000DX-200 p.3
1001DX & 1001DX-200 p.9
1003DX p.15
1005DX p.21
General information p.27
Serial #
Form # ADM-Speedster
2-12
13655 Stowe Dr., Poway, Ca. 92064
1
®
2
1000DX & 1000DX-200 SPEEDSTER
1000DX & 1000DX-200 SPEEDSTER® BACK
1000DX & 1000DX-200 SPEEDSTER® FRONT
1
9
11
2
12
10
3
4
13
5
8
14
6
7
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Solution lid
4. Female quick disconnect (QD)
5. Front handle
16
6. Front vent
7. 5” locking casters
8. Solution tank
9. Recovery lid
10.
11. Recovery tank
12. Push handle
13. Drain valve
1000DX & 1000DX-200 SPEEDSTER® ITEMS INCLUDED
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
H375 - Hose Hanger
(4) screws
H226 Drain Elbow
15
14. Power cord
15. Back vent
16. 12” Rear wheels
1000DX & 1000DX-200 SPEEDSTER® CORD
Plug the power cord into a single, 20A grounded wall outlet.
3
1000DX & 1000DX-200 SPEEDSTER
1000DX & 1000DX-200 SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1000DX & 1000DX-200 SPEEDSTER® SWITCHES
Vac 1 Vac 2
Pump
Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port.
Turn on Vac 1, Vac 2 and Pump switches.
1000DX & 1000DX-200 SPEEDSTER® BALL FLOAT
1000DX & 1000DX-200 SPEEDSTER® FILL
SOLUTION TANK
Lift lid and manually fill the tank.
An internal ball float automatically turns off the machine’s vacuum
when the water in the solution tank reaches its maximum level.
Empty the recovery tank as needed using the rear drain valve.
4
1000DX & 1000DX-200 SPEEDSTER
1000DX & 1000DX-200 SPEEDSTER® DUMP VALVE
1000DX & 1000DX-200 SPEEDSTER®
FILTER MAINTENANCE
INTAKE
FILTER
Attach the 45˚ drain elbow to the drain spout in back. Lift up the
dump valve and empty the tank.
Check and clean solution tank filter daily by twisting off, rinsing with
clean water and replacing.
1000DX & 1000DX-200 SPEEDSTER®
LOCKING CASTERS
MYTEE® SYSTEM MAINTAINER
Locking casters help keep the machine remain stationary during
use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
5
Order parts at: www.mytee.com/products/product.php?id=1000DX
6
A
B
C
D
E
F
H347
B160
B186
B136
B105
H299
H222
B172
H273
P731
P732
H215
H213
H211
G052
H770
H912
H307
B216
B210
B119A
H378
H485
AH120
B107
B109
B135
B102
B656
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
8
PH628-24
H217
PH615-26
23
24
25
H220
13
H544
H221
12
22
H371
11
H601
P750
G004
H500
G059
C310
H219
10
16
17
18
19
20
21
H251
9
E550
H254
H768
H666
7
8
15
H202
14
H210
5
6
H343
H296
2
3
H216
C317
4
PART NO.
1
8
ITEM
NO.
7
ball valve, 1/4''
tee, brass, 1/4" mpt
qd, brass, 1/4" f
nipple, brass, 1/4"m, hex
adapter, brass, 1/4" barb x 1/4" mpt
handle, breeze and dx
sol hose, 28" x 1/4", 1/4 fpt
filter, strainer, 1/2"
bracket, front hinge, sp/fb
bushing, brass, 1/2"mpt x 3/8" fpt, hex
washer, star, 1/4" steel zinc
nipple, brass, 3/8" x close
washer, buna 1-1/8" od x 3/16" id
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
bracket, rear, fb/spy
nut, hex, 1/4-20 s/s
washer, 1/4" lock, s/s
washer, 1/4"id x 1"od, flat, s/s
base, speedster
sol tank, speedster
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
nut, kep, #10-32 zinc
washer, 11/16"id x 1-1/2"od x .075, s/s
screw, #10-32 x 1-1/4" phil pan head, zinc
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
clamp, hose, 5/16-29/32
adapter, brass, 1/2" barb x 3/8" fsw, ball end
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
vac hose, 2", wire reinforced
clamp, hose, 2-1/4 dia
sol hose, 1/2" kuri 100psi
cuff hose, 2 X 2, wire reinforced
plate, manifold, parallel
manifold, dual vac, parallel
gasket, vacuum motor
vac support, 2 stage, 3-1/8"
exhaust boot, plastisol
vac motor, 2 stage high performance
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
power cord, pigtail, 30", 12/3, black
fitting, strain relief, cord
nut, lock, 1/2" steel
axle, 18.25" x .50" dia
cap, axle, 1/2"
wheel, 12"
washer, axle, cut 1/2" id
caster, 5"
bolt, 1/4-20 x 3/4" hex head, s/s
washer, 1/4" flat, s/s
nut, lock, 1/4-20, nylon insert, s/s
guard, cooling fan, wire
screw, #10 x 5/8" hex head, zinc
fan, cooling, 115V
DESCRIPTION
7
1
1
1
2
1
1
2
1
1
1
2
1
6
8
1
2
4
6
1
1
1
6
5
4
1
1
4
1
1
1
3
1
1
1
1
2
6
2
2
11
1
1
1
1
2
2
4
2
20
19
13
3
12
1
QTY.
MSRP
$0.99 ea
$11.49 ea
$3.19 ea
$1.99 ea
$9.99 ea
$0.99 ea
$41.99 ea
$0.99 ea
$23.19 ea
$0.99
$0.99 ea
$0.99
$2.99 ea
$0.99 ea
$21.49 ea
$13.49 ea
$17.99 ea
$5.49 ea
$3.19 ea
$1.99 ea
$6.99 ea
$35.49 ea
$6.49 ea
$8.99 ea
$2.49 ea
$0.99 ea
$1.99 ea
$1.99 ea
$0.99 ea
$9.99 ea
$0.99 ea
$0.99
$0.99 ea
$141.99 ea
$141.99 ea
$9.49 ea
$0.99 ea
$0.99 ea
$0.99 ea
$4.99 ea
$3.19 ea
$1.99 ea
$3.49 ea
$8.99 ea
$8.99/ft
$1.49 ea
$8.99/ft
$12.49 ea
$13.49 ea
$15.99 ea
$8.99 ea
$3.99 ea
$4.99 ea
$103.99 ea
6
6
H225
H226
58
59
H612
H338
P685
H390A
B142
C322D
75
76
77
78
79
80
Washer, #8, flat regular
4
piglet filter
gasket, strip, 3/4" x 36" x 1/8"
hanger, wire formed, hose
screw, 10-32 x 1/2" phil pan head, s/s
banana bag, mesh bag, yellow
Cuff-Lynx, 2" x 1.5" reducer
Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx
power cord, ext 50', 12/3 black
5
DESCRIPTION
G008
G085
H375
H230
G029
H141
H110
E530
inlet, 2"
bracket, "L" (all extracters)
coupling, brass, 1/4" fpt x 1/4" fpt
pump, 220psi, demand, 115V
plate, switch, sp, 3 hole
PART NO.
ITEMS NOT SHOWN
gasket, 2" inlet
H135
E515
H389
Cuff-Lynx, 2" m cuff x 2" mpt
switch, rocker, 2 position
screw, #10-32 x 1/2" SHCS, alloy
G083
gasket, 7", vac lid
72
73
74
66
pipe, pvc, 2"
lid, vac tank, black, 7"
screw, #8 x 5/8 phil oval, s/s
elbow, inlet assembly 2"
vac tank, speedster
G091
65
elbow, 2" float
screw, 8 x 1/2", hex head, zinc
G090
H304
A926
P733
P682
64
1
1
1
2
1
1
1
1
QTY
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
adaptor, pvc 2, fmsl x fmt
float, 2", ball style
valve, drain, 1-1/2"
spout, drain, 45 degree
sol hose, 1/4", 300 PSI
screw, #10-32 x 3/4" phil pan head, zinc
plate, mounting, QD
DESCRIPTION
4
67
68
69
70
71
P726
H297
63
G002
P684
H490
PH634-36
H256
H484
60
61
62
PART NO.
55
56
57
5
ITEM
NO.
3
3
MSRP
$10.99 ea
$6.99 ea
$4.49 ea
$151.99 ea
$6.99 ea
$0.99 ea
$3.99 ea
$13.99 ea
$0.99 ea
$2.49 ea
$36.99 ea
$0.99 ea
$15.99 ea
$190.99 ea
$11.99 ea
$7.99/ft
$0.99 ea
$11.49 ea
$6.49 ea
$6.99 ea
$18.49 ea
$20.99 ea
$3.19 ea
$6.49 ft
$0.99 ea
$4.99 ea
$6.29 pak
$4.99 ea
$10.99 ea
$0.99 ea
$3.99 ea
$3.99 ea
$3.99 ea
$74.99 ea
MSRP
1
2
1
1
1
3
1
3
3
1
1
6
1
1
1
1
3
1
1
1
1
1
1
1
4
1
QTY.
DATE
8/5/11
NAME
M LaBarbera
Part prices are subject to change.
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
2
SCALE: 1:48
1
DO NOT
SCALE DRAWING
SHEET 1 OF 2
C 1000DX-200
SIZE DWG. NO.
REV
PRODUCTS, INC.
858-679-1191
speedster
mytee
TITLE:
1
A
B
C
D
E
F
1000DX & 1000DX-200 SPEEDSTER
7
A
B
C
D
E
F
16
17
18
19
20
5
15
15
21
8
8
10
6
14
24
23
9
13
22
11
12
# 54
8
to QD
thru AH120
26
27
28
7
25
29
7
7
30
31
32
5
6
5
34
# 44
to sol tank
filter thru
B216
35
33
3
1
6
6
2
80
39
40
37
38
5
# 28
to pump "IN"
thru B186
40
41
42
43
41
6
39
5
44
31
36
6
45
5
46
47
6
5
38
4
4
15
48
39
50
49
40
55
79
50
57
51
56
54
52
3
53
62
3
59
60
61
58
63
65
64
2
78
41
66
2
77
34
69
67
76
70
68
DATE
8/5/11
NAME
73
M. LaBarbera
74
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
74
75
71
858-679-1191
1
DO NOT SCALE
DRAWING
SHE
D 1000DX-20
SCALE: 1:48
SIZE DWG. NO.
speedster
mytee PRODUCTS, I
TITLE:
72
1
1000DX & 1000DX-200 SPEEDSTER
Cord Input Primary
L2
GND
White
Green
Black
Inline Conn.
White
Black
Black
Black
SW-DPST
E515
Inline Conn.
Switch
Pressure
C322D
Inline Conn.
White
Pressure Pump
L2
Green
GND
L1
Black
1000DX
Inline Conn.
Green
Black
SW-DPST
E515
Inline Conn.
SW-DPST
E515
Inline Conn.
Vacuum Motor 2
C310
Inline Conn.
Vacuum Motor 1
C310
Inline Conn. Inline Conn.
Mytee Products
13655 Stowe Dr.
Poway, CA
Size: Letter
Number: 0000
Revision: A
92064
Time: 1:49:31 PM Sheet 1 of 1
Date: 11/30/2010
--File: C:\Compaines\GHI\Projects\Mytee Schematics\1000DX\1000DX.SCHDOC
Title
Green
White
Black
L2
Yellow
Black
Green
Black
L1
GND
White
Black
L2
Black
Brown
8
Blue
Green
GND
L1
L1
1000DX & 1000DX-200 SPEEDSTER
Black
1001DX & 1001DX-200 SPEEDSTER
1001DX & 1001DX-200 SPEEDSTER® FRONT
10
1
1001DX & 1001DX-200 SPEEDSTER® BACK
12
11
2
3
4
13
5
9
14
6
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Solution lid
4. Female quick disconnect (QD)
5. Front handle
7
16
6. Front cooling fan
7. Bottom handle
8. 5” locking casters
9. Solution tank
10.Recovery lid
11. Recovery tank
12. Push handle
13. Drain valve
14. Dual power cords
1001DX & 1001DX-200 SPEEDSTER® ITEMS INCLUDED
15
15. Back vent
16. 12” Rear wheels
1001DX & 1001DX-200 SPEEDSTER® CORDS
Left cord: Powers Vac 2 & Heater 2.
Right cord: Powers Vac 1, Heater 1 & Pump.
Yellow tag
indicates primary
cord.
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
H375- Hose Hanger
(4) screws
H226 Drain Elbow
Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.
9
1001DX & 1001DX-200 SPEEDSTER
1001DX & 1001DX-200 SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1001DX & 1001DX-200 SPEEDSTER® SWITCHES
Vac 1 Vac 2
Heater 1
Pump Heater 2
Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port.
“On” switches are located on the plate in front of the machine. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use pump,
turn on Pump switch. To activate heat, turn on Heater switch.
Heater 1 for 1000 watts of heat. Heater 2 for 2000 watts of heat.
1001DX & 1001DX-200 SPEEDSTER®
FILL SOLUTION TANK
1001DX & 1001DX-200 SPEEDSTER®
FILTER MAINTENANCE
INTAKE
FILTER
Lift lid and manually fill the tank.
Check and clean solution tank filter daily by twisting off, rinsing
with clean water and replacing.
10
1001DX & 1001DX-200 SPEEDSTER
1001DX & 1001DX-200 SPEEDSTER® BALL FLOAT
1001DX & 1001DX-200 SPEEDSTER® DUMP VALVE
An internal ball float automatically turns off the machine’s
vacuum when the water in the solution tank reaches its maximum level. Empty the recovery tank as needed using the rear
dump valve.
Attach the 45˚ drain elbow to the drain spout in back. Lift up the
dump valve and empty the tank.
1001DX & 1001DX-200 SPEEDSTER®
LOCKING CASTERS
MYTEE® SYSTEM MAINTAINER
Locking casters help keep the machine remain stationary during
use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
11
Order parts at: www.mytee.com/products/product.php?id=1001DX
12
A
B
C
D
E
F
7
Part prices are subject to change.
base, speedster
H666
H202
P731
H371
H254
H251
H219
AH156
B103
B108
B142
H273
H528
H256
E519
H274
H903A
E574
E573
AH105
H768
H601
P750
G004
H500
G059
H217
C310
H544
PH628-24
E550
H220
H221
B136
B105
B186
H299
B160
H347
PH615-26
C322D
H222
B172
H203
H211
G052
H213
H215
P732
H770
H912
H307
H316
H378
H201
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
8
bolt, 1/4x20x3/4" hex head
H210
5
7
bolt, 1/4-20 x 1/2", hex head, zinc
bracket, front hinge, sp/fb
bolt, 1/4x1-1/2", hex head zinc
washer, star, 1/4" steel zinc
bolt, 1/4-20 x 1 1/4"
washer, 1/4"id x 1"od, flat, s/s
washer, buna 1-1/8" od x 3/16" id
washer, 1/4" lock, s/s
nut, hex, 1/4-20 s/s
sol tank, speedster
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
bracket, rear, fb/spy
washer, 11/16"id x 1-1/2"od x .075, s/s
adapter, brass, 1/2" barb x 3/8" fsw, ball end
clamp, hose, 5/16-29/32
sol hose, 1/2" kuri 100psi
pump, 220psi, demand, 115V
screw, #10-32 x 1-1/4" phil pan head, zinc
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
nut, lock, 1/2" steel
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
cuff hose, 2 X 2, wire reinforced
vac hose, 2", wire reinforced
power cord, pigtail, 30", 12/3, black
fitting, strain relief, cord
clamp, hose, 2-1/4 dia
vac motor, 2 stage high performance
gasket, vacuum motor
vac support, 2 stage, 3-1/8"
exhaust boot, plastisol
Thermostat, 310°F ± 10°F, Manual, 1/4"
Thermostat, 200°, Auto, 1/4"
hose, 3/8" x 17-1/2", (OAL), f
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
plate, manifold, parallel
manifold, dual vac, parallel
valve, brass, 1/4" check
coupling, brass, 1/4" fpt x 1/4" fpt
nut, kep, #10-32 zinc
bracket, heater mounting, dual
screw, #10-32 x 3/4" phil pan head, zinc
heating rod, 1000W, 115V
screw, #6x3/16,phil pan head, self-tapping
heater, aluminum cast, single
axle, 18.25" x .50" dia
washer, axle, cut 1/2" id
wheel, 12"
cap, axle, 1/2"
hose, 3/8", (OAL), f x fs, 5400 gray
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
caster, 5"
washer, 1/4" flat, s/s
screw, #10 x 5/8" hex head, zinc
guard, cooling fan, wire
fan, cooling, 115V
nut, lock, 1/4-20, nylon insert, s/s
H343
H296
C317
H216
DESCRIPTION
1
2
3
4
8
PART NO.
ITEM
NO.
2
1
2
2
2
6
6
4
2
1
8
1
5
1
4
1
1
4
1
2
1
1
1
1
1
2
2
3
2
2
6
2
2
2
1
11
1
1
1
2
8
1
6
2
10
2
1
4
2
2
2
2
1
14
2
19
12
3
1
13
QTY.
6
6
$0.99 ea
$8.99 ea
$0.99
$0.99 ea
$0.99 ea
$0.99 ea
$1.99 ea
$0.99
$0.99 ea
$141.99 ea
$0.99 ea
$9.99 ea
$0.99 ea
$3.49 ea
$1.99 ea
$8.99/ft
$151.99 ea
$0.99 ea
$9.49 ea
$1.99 ea
$4.99 ea
$3.19 ea
$8.99 ea
$12.49 ea
$8.99/ft
$11.49 ea
$3.19 ea
$1.49 ea
$103.99 ea
$8.99 ea
$3.99 ea
$4.99 ea
$17.99 ea
$16.49 ea
$31.99 ea
$0.99 ea
$13.49 ea
$15.99 ea
$13.99 ea
$4.49 ea
$0.99 ea
$29.99 ea
$0.99 ea
$51.99 ea
$0.99 ea
$78.99 ea
$9.99 ea
$0.99 ea
$41.99 ea
$0.99 ea
$23.99 ea
$4.49 ea
$141.99 ea
$0.99
$23.19 ea
$0.99 ea
$0.99 ea
$2.99 ea
$21.49 ea
$0.99 ea
MSRP
G002
P684
P682
H297
H490
P726
A926
G091
G090
H304
G083
H135
E511
E516
E515
E512B
H348
H612
P685
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
5
4
Cuff-Lynx, 2" x 1.5" reducer
Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx
power cord, ext 50', 12/3 black
H141
H110
E530
4
piglet filter
gasket, strip, 3/4" x 36" x 1/8"
hanger, wire formed, hose
screw, 10-32 x 1/2" phil pan head, s/s
banana bag, mesh bag, yellow
DESCRIPTION
inlet, 2"
Washer, #8, flat regular
light, indicator, 125v (amber)
plate, switch, sp, 4 hole
lid, vac tank, black, 7"
screw, #8 x 5/8 phil oval, s/s
gasket, 2" inlet
Cuff-Lynx, 2" m cuff x 2" mpt
light, red, 250v
switch, rocker, 3 position
switch, rocker, 2 position
elbow, 2" float
elbow, inlet assembly 2"
gasket, 7", vac lid
screw, 8 x 1/2", hex head, zinc
float, 2", ball style
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
adaptor, pvc 2, fmsl x fmt
pipe, pvc, 2"
valve, drain, 1-1/2"
spout, drain, 45 degree
bracket, "L" (all extracters)
screw, #10-32 x 1/2" SHCS, alloy
controller, circuit light
vac tank, speedster
filter, strainer, 1/2"
ball valve, 1/4''
plate, mounting, QD
nipple, brass, 3/8" x close
bushing, brass, 1/2"mpt x 3/8" fpt, hex
qd, brass, 1/4" f
sol hose, 1/4", 300 PSI
adapter, brass, 1/4" barb x 1/4" mpt
tee, brass, 1/4" mpt
handle, breeze and dx
sol hose, 28" x 1/4", 1/4 fpt
nipple, brass, 1/4"m, hex
DESCRIPTION
G008
G085
H375
H230
G029
PART NO.
ITEMS NOT SHOWN
H225
H226
77
78
B656
H484
B216
B210
68
69
70
71
B119A
B102
67
H390A
H389
E564
P733
PH634-20
B109
B135
64
65
66
73
74
75
76
H485
AH120
B107
61
62
63
72
PART NO.
5
ITEM
NO.
3
3
1
1
2
1
1
1
2
1
QTY
1
3
1
1
1
6
1
1
2
1
3
1
1
1
3
1
1
1
1
1
1
2
4
1
1
1
1
1
1
1
1
1
1
1
1
1
2
QTY.
$3.99 ea
$3.99 ea
$74.99 ea
$6.29 pak
$4.99 ea
$10.99 ea
$0.99 ea
$3.99 ea
MSRP
$10.99 ea
$0.99 ea
$9.99 ea
$6.99 ea
$36.99 ea
$0.99 ea
$2.49 ea
$3.99 ea
$5.99 ea
$14.99 ea
$13.99 ea
$11.49 ea
$15.99 ea
$11.99 ea
$0.99 ea
$18.49 ea
$6.49 ea
$6.99 ea
$7.99/ft
$20.99 ea
$3.19 ea
$6.99 ea
$0.99 ea
$62.49 ea
$190.99 ea
$6.49 ea
$13.49 ea
$4.99 ea
$1.99 ea
$2.49 ea
$17.99 ea
$6.49 ft
$1.99 ea
$5.49 ea
$6.99 ea
$35.49 ea
$3.19 ea
MSRP
DATE
8/5/11
NAME
M LaBarbera
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
2
SCALE: 1:48
1
DO NOT
SCALE DRAWING
SHEET 1 OF 2
C 1001DX-200
SIZE DWG. NO.
REV
PRODUCTS, INC.
858-679-1191
speedster
mytee
TITLE:
1
A
B
C
D
E
F
1001DX & 1001DX-200 SPEEDSTER
13
A
B
C
D
E
F
20
24
21
21
8
18
19
23
8
15
17
16
22
26
28
# 63
to QD
thru B107
5
4
29
30
31
25
26
13
13
27
33
14
7
7
36
35
11
# 39
to pump "OUT"
thru B136
12
7
32
34
37
38
# 13
10
9
to heater "IN"
thru AH156
44
43
41
8
39
6
6
6
42
40
47
7
5
17
5
# 70
to sol tank
filter
thru B216
48
3
2
5
1
5
57
55
# 41
50
55
51
51
to Pump "IN"
thru B186
49
50
56
53
52
70
54
42
72
71
58
4
5
4
4
59
60
5
26
61
62
63
51
# 25
to heater "OUT"
thru AH105
52
50
64
68
63
3
65
69
3
19
78
67
66
83
79
80
77
84
81
82
2
75
85
2
74
55
86
74
DATE
8/5/11
NAME
94
M. LaBarbera
95
76
88
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
73
97
87
96
93
91
92
90
858-679-1191
1
DO NOT SCALE
DRAWING
REV
SHEET 2 OF 2
D 1001DX-200
SCALE: 1:48
SIZE DWG. NO.
speedster
mytee PRODUCTS, INC.
TITLE:
89
1
A
B
C
D
E
F
1001DX & 1001DX-200 SPEEDSTER
Inline Conn.
L1 Black
GND
L2 Inline Conn.
White
Cord Input Secondary
Entry Location, Bottom
or Far Left
Green
White / Red
C322D
Heater Switch
Black
3-Position
E516
Red
Black
E511
Lamp Heater 2
E511
Lamp Heater 1
Orange
SW-DPST
E515
Inline Conn.
Pressure
Switch
Black
Red
Pressure Pump
Inline Conn.
Green
White / Red
Inline Conn.
L2 Black White
Orange / Black
Red
Vacuum Motor 1
Inline Conn.
White
Black
Green
L2
GND
Green
Vacuum Motor 2
SW-DPST
E515
Black
Inline Conn.
C310
GND Green
Inline Conn.
Yellow Black L1
White
Orange
1001DX
Thermal
Switch
C519
Green
Green
Red
Black
Thermal
Switch
C519
Mytee Products
13655 Stowe Dr.
Poway, CA
Size: Letter
Number: 0000
Revision: A
92064
Time: 10:45:09 AM Sheet 1 of 1
Date: 11/30/2010
--File: C:\Compaines\GHI\Projects\Mytee Schematics\1001DX\1001DX.SCHDOC
Title
Red
SW-DPST
E515
Inline Conn.
White / Red
White
C310
Inline Conn.
L2 Black White
GND Green
Inline Conn.
Brown Black L1
Cord Input Primary
Entry Location, Top or Far Right
White / Red
Red
Black
White Red
L2
Heater 1
L1
Red
Cooling Fan
C317
White / Red
White
White / Red
Green
GND
White / Red
L2
L1
White
Red
L1b
L2b
Pink 18 AWG
Light 2
Pink 18 AWG Light 1 L2a
L1
GND
L2
GND
Heater 2
White
Thermal Switch
Green
Orange / Black
White
Green
Black
Thermal Switch
Green
Orange
L1
Black
14
Blue
L1a
E564
Circuit Detector
E512B
Lamp Amber
Black
1001DX & 1001DX-200 SPEEDSTER
1003DX SPEEDSTER
1003DX SPEEDSTER® FRONT
1
1003DX SPEEDSTER® BACK
10
11
2
12
3
4
5
13
9
14
6
7
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Solution lid
4. Female quick disconnect (QD)
5. Front handle
17
15
8
16
6. Front cooling fan
7. Prime Valve
8. Pressure Regulator
9. Solution tank
10.Recovery lid
11. Push handle
12. Recovery tank
13. Drain valve
14. Back vent
15. Dual Power cords
1003DX SPEEDSTER® ITEMS INCLUDED
16. 12” Rear wheels
17. 5” locking casters
1003DX SPEEDSTER® CORD
Left cord: Powers Vac 2 & Heater 2.
Right cord: Powers Vac 1, Heater 1 & Pump.
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
H375- Hose Hanger
(4) screws
H226 Drain Elbow
Yellow tag
indicates primary
cord.
Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.
15
1003DX SPEEDSTER
1003DX SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1003DX SPEEDSTER® SWITCHES
Vac 1
Vac 2
Pump
Heater
1
2
“On” switches are located on the plate in front of the machine. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use pump,
turn on Pump switch. To activate heat, use lower right switch.
Press to the left for 1,000 watts, press to the right for 2,000 watts.
1003DX SPEEDSTER® FILL SOLUTION TANK
1003DX SPEEDSTER® PRIME VALVE
& PRESSURE REGULATOR
Sp
Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s®
Cuff-Lynx™ vacuum hose port.
16
l
Prime the pump by turning the valve to the Prime position (as
shown above) for 30 seconds, then turn right to the Run position.
Turn the Pressure Regulator to the left to decrease water pressure. Turn the Pressure Regulator to the right to increase water
pressure.
Lift lid and manually fill the tank.
be
LOWER PSI
La
RUN POSITION
e
PRESSURE
REGULATOR
im
Pr
HIGHER PSI
r
te
ds
ee
PRIME POSITION
1003DX SPEEDSTER
1003DX SPEEDSTER® FILTER MAINTENANCE
1003DX SPEEDSTER® BALL FLOAT
INTAKE
FILTER
An internal ball float automatically turns off the machine’s vacuum
when the water in the solution tank reaches its maximum level.
Empty the recovery tank as needed using the rear dump valve.
Check and clean solution tank filter daily by twisting off, rinsing
with clean water and replacing.
MYTEE® SYSTEM MAINTAINER
1003DX SPEEDSTER® DUMP VALVE
& LOCKING CASTERS
Above, empty the recovery tank by attaching the 45˚ drain elbow to
the drain spout in back. Lift up the dump valve and empty the tank.
Below, locking casters help keep the machine remain stationary
during use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
17
Order parts at: www.mytee.com/products/product.php?id=1003DX
18
A
B
C
D
E
F
washer, axle, cut 1/2" id
wheel, 12"
cap, axle, 1/2"
axle, 18.25" x .50" dia
H666
P731
H254
H251
H219
3
4
5
6
7
Part prices are subject to change.
8
G090
P726
P682
57
58
61
H490
56
P733
P684
55
A926
G002
54
60
H225
H226
52
53
59
B102
H378
51
B656
B109
48
49
50
H484
C313C
H485
B107
44
45
46
G052
47
H390A
42
43
B160
34
H912
B172
33
41
B242
B186
C313
31
32
40
B246
30
H299
B216
B105
29
38
39
H544
B135
27
28
H347
H217
26
B119A
B210
H501
35
C302
24
25
36
37
G004
H601
20
23
B103
19
P750
E573
E571
17
18
G059
E574
16
22
E519
15
21
H528
H273
H903A
12
13
E550
11
14
H371
H221
H220
8
9
10
7
lid, vac tank, black, 7"
elbow, inlet assembly 2"
vac tank, speedster
elbow, 2" float
pipe, pvc, 2"
float, 2", ball style
valve, drain, 1-1/2"
spout, drain, 45 degree
gasket, cam fitting polyethylene, 2.35" OD 1.90"
ID
adaptor, pvc 2, fmsl x fmt
bracket, front hinge, sp/fb
qd, brass, 1/4" f
ball valve, 1/4''
adapter, brass, 1/4" barb x 1/4" mpt
regulator, 450 psi, silver spring
plate, mounting, QD
handle, breeze and dx
nipple, brass, 1/4"m, hex
washer, buna 1-1/8" od x 3/16" id
bracket, "L" (all extracters)
bracket, rear, fb/spy
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
washer, 11/16"id x 1-1/2"od x .075, s/s
nipple, brass, 3/8" x close
filter, strainer, 1/2"
bushing, brass, 1/2"mpt x 3/8" fpt, hex
clamp, hose, 5/16-29/32
adapter, brass, 1/2" barb x 3/8" fsw, ball end
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
pump, 500 psi, 115V
plug, brass, 3/8" mpt, hex
bushing, brass, 3/8"mpt x 1/4"
cuff hose, 2 X 2, wire reinforced
tee, brass, 1/4" mpt
clamp, hose, 2-1/4 dia
vac support, 3 stage, 4-1/16"
vac motor, 3 stage, 120V, tangential
gasket, vacuum motor
exhaust boot, plastisol
manifold, dual vac, parallel
plate, manifold, parallel
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
Thermostat, 200°, Auto, 1/4"
heating rod, 600W, 115V
Thermostat, 310°F ± 10°F, Manual, 1/4"
heating rod, 1000W, 115V
nut, kep, #10-32 zinc
bracket, heater mounting, dual
heater, aluminum cast, single
power cord, pigtail, 30", 12/3, black
nut, lock, 1/2" steel
fitting, strain relief, cord
caster, 5"
base, speedster
fan, cooling, 115V
guard, cooling fan, wire
H296
C317
7
DESCRIPTION
2
8
PART NO.
ITEM
NO.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
6
2
1
1
5
1
1
1
10
1
3
1
1
4
1
1
2
3
6
2
2
2
1
1
8
2
1
2
1
4
1
2
2
2
2
1
2
2
6
2
1
1
3
QTY.
MSRP
6
$36.99 ea
$15.99 ea
$190.99 ea
$11.49 ea
$7.99/ft
$18.49 ea
$6.99 ea
$6.49 ea
$20.99 ea
$3.19 ea
$8.99 ea
$17.99 ea
$13.49 ea
$1.99 ea
$86.99 ea
$4.99 ea
$6.99 ea
$3.19 ea
$1.99 ea
$6.99 ea
$9.99 ea
$8.99 ea
$0.99 ea
$1.99 ea
$6.49 ea
$2.49 ea
$1.99 ea
$3.49 ea
$9.49 ea
$13.99 ea
$588.99 ea
$1.99 ea
$3.19 ea
$12.49 ea
$5.49 ea
$1.49 ea
$4.99 ea
$139.99 ea
$8.99 ea
$4.99 ea
$15.99 ea
$13.49 ea
$4.49 ea
$16.49 ea
$49.99 ea
$17.99 ea
$51.99 ea
$0.99 ea
$29.99 ea
$78.99 ea
$11.49 ea
$1.99 ea
$3.19 ea
$9.99 ea
$41.99 ea
$0.99 ea
$0.99
$23.19 ea
$141.99 ea
$21.49 ea
$2.99 ea
6
5
105
104
103
4
Cuff-Lynx, 2" to 1.5" reducer
screw, 10-32 x 1/2", phil pan head, s/s
hanger, wire formed, hose
H141
H230
H375
4
Cuff-Lynx, female swivel x female thread 2"
H140
5
DESCRIPTION
power cord, ext, 50', 12/3, black
controller, circuit light
piglet filter
gasket, strip, 3/4" x 36" x 1/8"
Items Not Shown
Washer, #8, flat regular
screw, #8-32 x 3/8" SHCS, alloy
screw, #10-32 x 1/2" SHCS, alloy
bolt, 1/4x1-1/2", hex head zinc
screw, 10 x 3/4, self-tap, hex head, zinc
sol hose, 1/4", 300 PSI
nut, hex, 1/4-20 s/s
washer, 1/4" lock, s/s
washer, 1/4"id x 1"od, flat, s/s
bolt, 1/4-20 x 1 1/4"
sol tank, speedster
solution hose, black, low pressure, 1/2"
sol hose, 1/2" kuri 100psi
vac hose, 2", wire reinforced
hose, 3/8" x 14-1/2" (OAL), f surge
2
1
1
1
QTY
2
1
1
1
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
bolt, 1/4-20 x 1/2", hex head, zinc
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
sol hose, 28" x 1/4", 1/4 fpt
hose, 3/8" x 6.5", (OAL), f x fsw, 5400 Gray
screw, #6x3/16,phil pan head, self-tapping
bolt, 1/4-20 x 1" hex head, s/s
screw, 10-32 x 3/4" phil pan head, zinc
washer, 1/4" flat, s/s
screw, #10 x 5/8" hex head zinc
nut, lock, 1/4-20, nylon insert, s/s
hose, pulse BLK 49"(OAL), 1/4"fswl x 1/4"fswl
filter, strainer, 1/4"
sol hose, 1/4", 300psi, black
adapter, brass, 1/4" sw barb x 1/4" fpt, w/gasket
plug, brass, 1/4"mpt, hex
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
inlet, 2"
coupling, brass, 1/4" fpt x 1/4" fpt
gauge, pressure, 2000 PSI
switch, rocker, 3 position
switch, rocker, 2 position
light, red, 250v
plate, switch, sp, 4 hole w/gauge
light, indicator, 125v (amber)
Cuff-Lynx, 2" m cuff x 2" mpt
gasket, 2" inlet
gasket, 7", vac lid
screw, #8 x 5/8 phil oval, s/s
DESCRIPTION
PART NO.
E530
E564
G008
G085
H612
H246
H389
H316
H118
PH634-36
100
101
102
H215
H213
98
99
H211
H203
P732
PH615-12
PH615-36
PH628-20
AH184
H770
H201
H768
AH108S
AH156
H274
H342
H256
H210
96
97
95
94
93
91
92
90
88
89
87
86
85
83
84
82
H343
H216
AH117
79
80
81
B119
PH634-20
B110
B127
B652
77
78
75
76
74
P685
B142
H308D
71
72
73
E516
70
E515
E511
68
69
H337
67
E512B
H135
66
G083
65
G091
H304
PART NO.
64
63
ITEM
NO.
62
$0.99 ea
MSRP
$0.99
$0.99
$0.99
$0.99
$0.99
$6.49 ft
$0.99
$0.99
$0.99
$0.99
$141.99 ea
$5.99 ft
$8.99/ft
$8.99/ft
$27.99 ea
$0.99
$0.99
$0.99
$26.49 ea
$23.99 ea
$0.99
$0.99
$0.99
$0.99
$0.99
$0.99
$19.99
$3.99 ea
$6.49/ft
$3.99 ea
$0.99
$8.49 ea
$10.99 ea
$4.49 ea
$38.99 ea
$14.99 ea
$13.99 ea
$5.99 ea
$8.99 ea
$9.99 ea
$3.99 ea
$2.49 ea
$11.99 ea
3
MATERIAL
ANGULAR: MACH .5
ONE PLACE DECIMAL
TWO PLACE DECIMAL
THREE PLACE DECIMAL
3
.03
.05
.003
DIMENSIONS ARE IN INCHES
TOLERANCES:
UNLESS OTHERWISE SPECIFIED:
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE FINISH
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
$0.99 ea
$10.99 ea
$3.99 ea
$3.99 ea
MSRP
$74.99 ea
$62.49 ea
$6.29 pak
$4.99 ea
3
2
1
2
3
1
2
4
6
2
1
1
1
1
1
8
8
10
2
1
10
12
6
20
12
16
1
1
1
1
1
1
1
1
1
1
3
2
1
1
1
1
1
6
QTY.
NAME
D. Cano
2
COMMENTS:
CHECKED
DRAWN
2
DATE
2/29/12
SCALE: 1:48
1
DO NOT
SCALE DRAWING
1003DX
SIZE DWG. NO.
C
SHEET 1 OF 2
REV
OD
PRODUCTS, INC.
858-679-1191
1003DX
mytee
TITLE:
1
A
B
C
D
E
F
1003DX SPEEDSTER
19
A
B
C
D
E
90
F
22
11
*
23
24
7
10
89
81
8
26
9
20
8
17
27
80
85
1
16
86
6
15
18
8
19
21
91
13
12
81
88
25
7
7
82
87
3
14
19
83
4
84
92
73
28
2
29
30
6
81
5
45
77
80
31
6
33
34
19
1
76
89
82
33
41
35
83
35
94
93
78
32
35
30
49
5
5
42
74
75
47
40
51
89
39
88
95
38
97
36
43
98
4
37
97
4
99
82
97
81
101
82
89
98
44
43 87
48
28
PROPRIETARY AND CONFIDENTIAL
45
100
84
55
57
3
52
54
58
102
MATERIAL
ANGULAR: MACH .5
ONE PLACE DECIMAL
TWO PLACE DECIMAL
THREE PLACE DECIMAL
.03
.05
.003
DIMENSIONS ARE IN INCHES
TOLERANCES:
UNLESS OTHERWISE SPECIFIED:
50
53
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE FINISH
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
46
45
56
3
NAME
59
D. Cano
2
COMMENTS:
CHECKED
DRAWN
2
2/2912
DATE
72
63
62
71
19
65
105
14
1
DO NOT
SCALE DRAWING
66
68
104
REV
OD
SHEET 2 OF 2
1003DX
1003DX
SCALE: 1:6
67
64
PRODUCTS, INC.
858-679-1191
SIZE DWG. NO.
C
TITLE:
mytee
79
60
61
1
A
B
69
C
D
E
F
1003DX SPEEDSTER
20
1003DX
E511
Lamp Heater 2
E511
Lamp Heater 1
Orange
Orange / Black
Black
Mytee Products
13655 Stowe Dr.
Poway, CA
Revision: A
Size: Legal
Number: 0000
92064
Date: 12/7/2010
Time: 10:34:12 AM Sheet 1 of 1
--File: C:\Compaines\GHI\Projects\Mytee Schematics\1003DX\1003DX.SCHDOC
Title
Heater Switch
Black
3-Position
Red
E516
Red
Black
SW-DPST
E515
Pressure Pump
C313
Inline Conn.
Red
Vacuum Motor 1
Cord Input Secondary
Entry Location,
Bottom or Far Left
White / Red
C302
Inline Conn.
SW-DPST
E515
Black
Inline Conn.
Vacuum Motor 2
Inline Conn.
L1 Black
GND
Inline Conn.
L2 White
White / Red
Red
SW-DPST
E515
Inline Conn.
C302
White / Red
White / Red
Orange
Thermal Switch
600W
GND
White
Red
Black
Thermal Switch
1000W
GND
Heater 2
White
Red
Cooling Fan
E317
White / Red
White
White / Red
E564
E512B
Lamp Amber
Red
L1b
L2b
Pink 18 AWG Light 2
Pink 18 AWG Light 1 L2a
L1a
Circuit Detector
Cord Input Primary
Entry Location, Top or Far Right
White
Black
L1
GND
L2
White / Red
Red
Black
White Red
White / Red
Heater 1
L2
GND White / Red
L1
Blue
L1
Black
L2 Black White
GND
Inline Conn.
Black L1
Yellow
White/Red
L2 Black
GND
Inline Conn.
Brown
Thermal Switch
L2
L1
Orange / Black
Thermal Switch
L2
L1
Orange
White
Black
1003DX SPEEDSTER
1005DX SPEEDSTER
1005DX SPEEDSTER® FRONT
1
1005DX SPEEDSTER® BACK
10
11
2
12
3
4
5
13
9
14
6
7
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Solution lid
4. Female quick disconnect (QD)
5. Front handle
17
15
8
16
6. Front vent
7. Prime Valve
8. Pressure Regulator
9. Solution tank
10.Recovery lid
11. Push handle
12. Recovery tank
13. Drain valve
14. Back vent
15. Dual Power cords
1005DX SPEEDSTER® ITEMS INCLUDED
16. 12” Rear wheels
17. 5” locking casters
1005DX SPEEDSTER® CORD
Left cord: Powers power Vac 2.
Right cord: Powers Vac 1 & Pump.
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
H375 - Hose Hanger
(4) screws
H226 Drain Elbow
Yellow tag
indicates primary
cord.
Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.
21
1005DX SPEEDSTER
1005DX SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1005DX SPEEDSTER® SWITCHES
Vac 1
Vac 2
Pump
“On” switches are located on the plate in front of the machine. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use pump,
turn on Pump switch. Bottom right switch has no use.
Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port.
Sp
LOWER PSI
Prime the pump by turning the valve to the Prime position (as
shown above) for 30 seconds, then turn right to the Run position.
Turn the Pressure Regulator to the left to decrease water pressure. Turn the Pressure Regulator to the right to increase water
pressure.
Lift lid and manually fill the tank.
22
l
RUN POSITION
be
PRESSURE
REGULATOR
La
HIGHER PSI
e
PRIME POSITION
im
Pr
1005DX SPEEDSTER® PRIME VALVE
1003DX
& PRESSURE REGULATOR
r
te
ds
ee
1005DX SPEEDSTER® FILL SOLUTION TANK
1005DX SPEEDSTER
1005DX SPEEDSTER® FILTER MAINTENANCE
1005DX SPEEDSTER® BALL FLOAT
INTAKE
FILTER
An internal ball float automatically turns off the machine’s vacuum
when the water in the solution tank reaches its maximum level.
Empty the recovery tank as needed using the rear dump valve.
Check and clean solution tank filter daily by twisting off, rinsing
with clean water and replacing.
MYTEE® SYSTEM MAINTAINER
1005DX SPEEDSTER® DUMP VALVE
& LOCKING CASTERS
Above, empty the recovery tank by attaching the 45˚ drain elbow to
the drain spout in back. Lift up the dump valve and empty the tank.
Below, locking casters help keep the machine remain stationary
during use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
23
Order parts at: www.mytee.com/products/product.php?id=1005DX
24
A
B
C
D
E
F
washer, 1/4" flat, s/s
washer, 1/4" lock, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
nut, lock, 1/4-20, nylon insert, s/s
H343
H378
H210
H213
H201
H216
H316
H202
H666
P731
3
4
5
6
7
8
9
10
11
C313
B172
H347
PH615A-10
B246
B242
PH615-36
B160
H601
G059
H217
PH628-24
H544
H768
C302A
G004
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Part prices are subject to change.
PH634-20
H256
61
62
8
B656
B102
PH634-36
B109
57
58
59
60
B186
C313C
53
54
56
H299
B216
51
52
55
H211
B119A
B210
50
H485
G052
48
49
G018
B105
27
47
AH108S
B103
B135
24
25
26
P750
B107
23
H501
P732
H307
H770
21
22
45
46
H221
H912
19
20
44
E550
H220
17
H251
H219
15
16
18
H254
H371
13
14
12
fan, cooling, 115V
H296
7
sol hose, 1/4", 300 PSI
screw, 10-32 x 3/4" phil pan head, zinc
ball valve, 1/4''
qd, brass, 1/4" f
sol hose, 1/4", 300 PSI
adapter, brass, 1/4" barb x 1/4" mpt
regulator, 450 psi, silver spring
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
washer, 11/16"id x 1-1/2"od x .075, s/s
nipple, brass, 3/8" x close
filter, strainer, 1/2"
bushing, brass, 1/2"mpt x 3/8" fpt, hex
washer, 1/4"id x 1"od, flat, s/s
handle, breeze and dx
washer, buna 1-1/8" od x 3/16" id
cover, sol tank (sp)
vac support, 3 stage, 4-1/16"
sol tank, speedster
manifold, dual vac, parallel
gasket, vacuum motor
cuff hose, 2 X 2, wire reinforced
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
motor, 3-stage, 115 cfm,14.5 amps
clamp, hose, 2-1/4 dia
vac hose, 2" wire reinforced, gray
exhaust boot, plastisol
adapter, brass, 1/2" barb x 3/8" fsw, ball end
plate, manifold, parallel
sol hose, 1/2" kuri 100 psi
plug, brass, 3/8" mpt, hex
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
solution hose, black, low pressure, 1/2"
clamp, hose, 5/16-29/32
pump, 500 psi, 115V
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
bushing, brass, 3/8"mpt x 1/4"
sol hose, 1/4" x 24 1/4"
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
tee, brass, 1/4" mpt
nipple, brass, 1/4"m, hex
washer, star, 1/4" steel zinc
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
nut, lock, 1/2" steel
bracket, rear, fb/spy
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
wheel, 12"
cap, axle, 1/2"
axle, 18.25" x .50" dia
washer, axle, cut 1/2" id
bolt, 1/4x20x3/4" hex head
caster, 5", Black hub & gray tread
base, speedster
bolt, 1/4x1-1/2", hex head zinc
screw, #10 x 5/8" hex head zinc
bracket, front hinge, sp/fb
guard, cooling fan, wire
C317
2
7
DESCRIPTION
8
PART NO.
ITEM
NO.
1
1
4
1
1
1
2
1
1
5
1
1
1
6
1
6
1
6
1
1
4
1
11
2
3
1
2
1
1
1
5
1
1
8
1
3
1
2
3
2
2
2
8
2
1
2
2
2
2
1
3
18
2
1
2
2
17
23
4
14
1
3
1
QTY.
6
6
$6.49 ft
$0.99 ea
$13.49 ea
$17.99 ea
$6.49 ft
$1.99 ea
$86.99 ea
$8.99 ea
$0.99 ea
$1.99 ea
$6.49 ea
$2.49 ea
$0.99 ea
$6.99 ea
$1.99 ea
$12.99 ea
$4.99 ea
$141.99 ea
$15.99 ea
$8.99 ea
$12.49 ea
$0.99 ea
$148.99 ea
$1.49 ea
$8.99/ft
$4.99 ea
$3.49 ea
$13.49 ea
$8.99/ft
$1.99 ea
$13.99 ea
$5.99 ft
$1.99 ea
$588.99 ea
$9.49 ea
$3.19 ea
$26.49 ea
$4.49 ea
$5.49 ea
$3.19 ea
$0.99 ea
$0.99 ea
$1.99 ea
$9.99 ea
$3.19 ea
$11.49 ea
$41.99 ea
$0.99 ea
$9.99 ea
$0.99 ea
$0.99
$23.19 ea
$141.99 ea
$0.99
$0.99 ea
$0.99
$0.99 ea
$0.99
$0.99 ea
$8.99 ea
$2.99 ea
$21.49 ea
MSRP
5
H422
E515
70
71
4
stop sign, register your product
manual, speedsters
ADM-SPEEDSTERS
4
REMOVED G034, FIXED VIEW ERRORS
B
5
ADDED AH117 AND FIXED BOM ERRORS
ORIGINAL DRAFT
A
OD
4/10/12
4/4/12
1/2007
DATE
Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx
H110
AD127
DESCRIPTION
Cuff-Lynx, 2" to 1.5" reducer
power cord, ext 50', 12/3 black
H141
E530
REV.
1
banana bag, mesh bag, yellow
REVISIONS
1
2
screw, 10-32 x 1/2" phil pan head, s/s
H230
G029
1
1
1
2
1
2
gasket, strip, 3/4" x 36" x 1/8"
hanger, wire forned, hose
G085
H375
1
MSRP
$3.99 ea
$3.99 ea
$74.99 ea
$3.99 ea
$0.99 ea
$4.99 ea
$10.99 ea
DJC
DJC
JFL
$19.99
$6.99 ea
$62.49 ea
$3.99 ea
$2.49 ea
$20.99 ea
$3.19 ea
$15.99 ea
$11.49 ea
$18.49 ea
$36.99 ea
$0.99 ea
$0.99 ea
$11.99 ea
$7.99/ft
$10.99 ea
$6.99 ea
$0.99 ea
$190.99 ea
$0.99 ea
$13.99 ea
$0.99 ea
$0.99 ea
$8.99 ea
$9.99 ea
$38.99 ea
$0.99 ea
$4.99 ea
$0.99 ea
MSRP
$6.29 pak
3
3
APPROVED
1
2
1
1
1
1
1
1
1
1
1
6
3
1
1
1
1
2
1
2
4
2
2
1
1
1
3
1
4
QTY.
QTY.
piglet filet
DESCRIPTION
ITEMS NOT SHOWN
hose, pulse BLK 49"(OAL), 1/4"fswl x 1/4"fswl
bracket, "L" (all extracters)
controller, circuit light
Cuff-Lynx, 2" m cuff x 2" mpt
gasket, 2" inlet
valve, drain, 1-1/2"
spout, drain, 45 degree
elbow, inlet assembly 2"
elbow, 2" float
float, 2", ball style
lid, vac tank, black, 7"
screw, #8 x 5/8 phil oval, s/s
screw, 8 x 1/2", hex head, zinc
gasket, 7", vac lid
pipe, pvc, 2"
inlet, 2"
adaptor, pvc 2, fmsl x fmt
bolt, 1/4-20 x 1 1/4"
vac tank, speedster
nut, hex, 1/4-20 s/s
switch, rocker, 2 position
plug, dome 3/8", black
nut, kep, #10-32 zinc
plate, switch, sp, 4 hole w/gauge
light, indicator, 125v (amber)
gauge, pressure, 2000 PSI
Washer, #8, flat regular
plate, mounting, QD
screw, #10-32 x 1/2" SHCS, alloy
DESCRIPTION
G008
AH117
H135
88
91
G083
87
H390A
E564
H225
H226
A926
84
85
86
89
90
P726
H490
82
83
78
79
G090
H304
P682
H297
G091
77
80
81
P685
P684
75
76
H215
H273
69
H203
P733
H337
68
72
E512B
67
73
74
H612
H308D
65
66
H484
H389
PART NO.
ITEM
NO.
63
64
NAME
D. Cano
DATE
4/2/12
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
2
SCALE: 1:8
1
DO NOT
SCALE DRAWING
1005DX
SIZE DWG. NO.
C
B
SHEET 1 OF 2
REV
PRODUCTS, INC.
858-679-1191
SPEEDSTER
mytee
TITLE:
1
A
B
C
D
E
F
1005DX SPEEDSTER
25
A
B
C
D
E
8
5
5
25
7
10
28
27
26
29
24
To pressure guage
thru AH108S
(#25)
F
5
30
6
8
4
31
23
8
6
3
5
2
25
To q.d.
thru B107
(#23)
9
1
32
30
35
29
34
29
30
30
37
7
11
10
5
33
To sol tank "IN"
thru B186
(#57)
7
39
36
38
12
22
21
41
5
13
13
44
40
3
6
14
20
10
45
43
43
42
41
6
19
18
15
17
16
48
5
5
49
50
41
53
51
52
53
53
53
53
54
55
47
4
4
58
59
60
To pump "IN"
thru B160
(#36)
57
46
61
26
58
62
65
66
3
To pump "OUT"
thru B107
(#24)
56
63
3
64
67
71
68
25
70
25
74
NAME
49
50
4/2/12
DATE
75
76
77
78
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
73
49
79
D. Cano
50
90
DRAWN
72
69
80
2
22
89
88
87
84
1
DO NOT
SCALE DRAWING
1005DX
B
REV
SHEET 2 OF 2
SPEEDSTER
SCALE: 1:8
86
85
PRODUCTS, INC.
83
858-679-1191
82
SIZE DWG. NO.
C
TITLE:
mytee
81
1
A
B
C
D
E
F
1005DX SPEEDSTER
Inline Conn.
L1 Black
GND
Green
L2 White
White / Red
Inline Conn.
Cord Input Secondary
Entry Location,
Bottom or Far Left
Cord Input Primary
Entry Location, Top or Far Right
26
Red
Black
SW-DPST
E515
C313
White
Black
White / Red
Green
Inline Conn.
Red
Vacuum Motor 1
Green
L2
Red
Black
Pressure Pump
SW-DPST
E515
Black
Inline Conn.
C302A
Inline Conn.
Green
C302A
Inline Conn.
Red
SW-DPST
E515
Inline Conn.
1005DX
Red
Black
Mytee Products
13655 Stowe Dr.
Poway, CA
Size: Letter
Number: 0000
Revision: A
92064
Time: 11:52:30 AM Sheet 1 of 1
Date: 11/30/2010
--File: C:\Compaines\GHI\Projects\Mytee Schematics\1005DX\1005DX.SCHDOC
Title
White / Red
White
White / Red
White
White
L1
GND
L2
L2 Black White
GND Green
Inline Conn.
Yellow Black L1
White
L2 Black
GND Green
Brown Black L1
White / Red
E564
Red
E512B
Lamp
Amber
Red
L1b
L2b
Pink 18 AWG
Light 2
Pink 18 AWG
Light 1 L2a
Black
L1a
Circuit Detector
White
Green
GND
L1
Blue
Vacuum Motor 2
1005DX SPEEDSTER
GENERAL INFORMATION
Dear Customer:
specify the Model and Serial Number when discussing your machine.
Congratulations on the purchase of your new Speedster® Extractor. As
you are already aware, the scene of the equipment world is becoming
more high tech, and we at Mytee Products Inc. strive to keep you on the
cutting edge with superior quality and technology.
Name Plate
The Model and Serial Number of your machine are shown on the name
plate located on the inside of the machine. This information is needed
when ordering repair parts for the machine. Use the space provided on
the front cover to note the Model and Serial Number of your machine for
future reference.
Keep in mind that the Speedster® Extractor is a machine, so neglect or
abuse will cause unnecessary damage and void the warranty. However
with simple maintenance the Speedster® will give quality performance for
many years to come.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and
the machine for damage. If damage is evident, save the shipping carton so
that it can be inspected by the carrier that delivered it. Contact the carrier
immediately to file a freight damage claim.
If warranty questions arise, please consult user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts
or ordering parts, please call an authorized Mytee Products Inc. Service
Center. To see an updated list, visit our website at www.mytee.com
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions.
Always read this information carefully and take the necessary steps to
protect personnel and property.
Before you begin using, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electrical shock. This machine is equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed in accordance with all local code and ordinances.
Do not remove ground pin; if missing, replace plug before use.
Is used to warn of immediate hazards that will cause severe personal
injury or death.
Is used to call attention to a situation that could cause severe personal
injury.
Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or service person
if you are in doubt as to whether the outlet is properly grounded. Do not
modify the plug provided with the machine. If it will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Is used to call attention to a situation that could cause minor personal
injury or damage to the machine or other property. When using an electrical appliance, basic precautions should always be followed, including the
following: Read all instructions before using this machine. This product is
intended for commercial use only.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary
adapter illustrated in Figures 2 and 3 may be used~to connect this plug to
a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is
not available. The temporary adapter should be used only until a properly
grounded outlet (Figure 1) can be installed by a qualified electrician. The
green colored rigid ear, tab or the like extending from the adapter must be
connected to a permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in place by a metal
screw. Grounding adapters are not approved for use in Canada.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended attachments.
3. Always unplug power cord from electrical outlet before attempting any
adjustments or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord
around sharp edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not
in use.
10. Do not allow to be used as a toy. Close attention is necessary when
used by or near children.
11. Do not use in areas where flammable or combustible material may be
present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any
other parts of this machine for this purpose.
14. Keep hair, loose clothing, fingers, and all parts of the body away from
all openings and moving parts.
15. Use extra care when using on stairs.
16. To reduce the risk of fire or electric shock, do not use this machine with
a solid-state speed control device.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When
replacing a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Grounded Outlet
Adapter
Metal
Screw
Grounding Pin
Grounded Outlet Box
Figure 1
Figure 2
Tab for Grounding
Screw
Figure 3
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee authorized Service Center using Mytee original replacement
parts and accessories. Call Mytee for repair parts or service. Please
27
GENERAL INFORMATION
After Use
17. The voltage and frequency indicated on the name plate must correspond to the wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations
may apply to the safe disposal of liquids which may contain: chemicals,
grease, oil, acid, alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
1. Before storing machine, drain, rinse and dry tanks and vacuum hose of
water and solution.
2. Store in a dry are in the upright position.
3. Open recover tank cover to promote air circulation.
4. Store indoors in a dry area. If storing in freezing temperatures, make
sure the machine and solution system are completely drained and dry.
Preparation
Maintenance Schedule
1. Remove furniture and other items from the area you are going to clean.
2. Vacuum carpet and upholstery, and remove debris.
3. Protect cabinets, walls and painted surfaces with drop cloths or plastic.
4. Inspect power cords for damages.
Latches are located in back to open tank for internal maintenance. To
keep machine in good working condition, follow machine’s daily and
weekly maintenance procedures. Check valves and relief valves should be
replaced annually.
Operating Instructions
1. Fill the solution tank.
2. Attach one end of a solution hose to a wand or other tool, the other end
to the Speedster’s® front quick disconnect.
3. Attach one end of a vacuum hose to the tool, the other end to the
Speedster’s® Cuff-Lynx™ vacuum hose port.
4. Plug in power cords.
• 1000DX and 1000DX-200 models – Plug single cord into single, 20A
grounded wall outlet.
• 1001DX, 1001DX-200 models – Using two separate circuits/breakers,
plug the left power cord into 20A grounded wall outlet to turn on Vac 2 and
Heater 2. Plug the right power cord into separate 20A grounded wall outlet
to turn on Vac 1, Heater 1 and Pump.
• 1003DX models – Using two separate circuits/breakers, plug the left
power cord into 20A grounded wall outlet to turn on Vac 2 and Heater 2.
Plug the right power cord into separate 20A grounded wall outlet to turn on
Vac 1, Heater 1 and Pump.
• 1005DX models – Using two separate circuits/breakers, plug the left
power cord into 20A grounded wall outlet to turn on Vac 2. Plug the right
power cord into separate 20A grounded wall outlet to turn on Vac 1 and
Pump.
The amber light indicator on the switch plate will illuminate brightly when
cords are plugged into two separate circuits. Do not use extension cords
longer than 50 feet.
5. Turn on switches.
• 1000DX, 1000DX-200, 1005DX models – Turn on Vac 1, Vac 2 and
Pump switches.
• 1001DX, 1001DX-200 and 1003DX – Turn on Vac 1, Vac 2 and Pump
switches. Turn on Heater switch if heat is being used. Wait several
minutes for water to heat. Heater switch has three positions: Off (middle);
1,000 watts using one heater (left); and 2,000 watts using two heaters
(right). Red lights on panel display indicate watts selected: one light =
1,000 watts; two lights = 2,000 watts; no lights = heaters are off.
6. 1003DX and 1005DX models – Prime Valve and Pressure Regulator
are located on the lower front of the extractor. To prime the pump, turn the
valve to the Prime position for 30 seconds, then turn horizontally to the
Run position. Turn the Pressure Regulator to the left to decrease the water
pressure. Turn to the right to increase water pressure. Level will be visible
on the pressure gauge. Monitor while adjusting, using Pressure Gauge on
Switch Panel.
7. Begin cleaning. Make two dry passes to every wet pass. Work away
from cords to avoid damage. To clean heavily soiled areas, repeat cleaning from a different direction.
8. Use a foam control solution in the recovery tank to prevent motor damage and check for foam build-up in recovery and solution tanks.
9. Empty the recovery tank as needed when the internal ball float automatically shuts off the vacuum. Attach the 45˚ drain elbow to the drain
spout in back. Lift up the dump valve and empty tank.
10. To relieve water pressure from the solution hose before disconnecting
it, squeeze the tool’s trigger five seconds after turning the power switches
off.
11. Once machine is off, unplug power cords. Remove solution and
vacuum hoses. Empty the recovery tank by attaching the 45˚ drain elbow
to the drain spout in back. Lift up the dump valve and empty tank.
12. 1003DX and 1005DX models – Water remaining in the solution tank
can be emptied by turning the Prime Valve to the right to move water into
the recovery tank. Empty recovery tank.
Maintenance item
Daily
Clean and inspect tanks.
Clean and inspect hoses.
Check and clean internal filters by twisting
off, rinsing with clean water and replacing.
Check power supply cable.
Clean machine with all-purpose cleaner
and cloth.
Check spray nozzles.
Flush solution system with Mytee® System
Maintainer.
Remove and float shut-off screen from
tank and clean. Simply pull off.
Inspect vacuum hoses for holes and loose
cuffs.
Inspect spray pattern for clogging. If
clogged, remove spray tips and soak them
in a recommended liquid neutralizer for
up to six hours. To remove spray tip, twist
spray tip body counter-clockwise.
Lubricate wheels with water resistant oil.
Inspect machine for water leaks and loose
hardware.
x
x
x
Once a week
x
x
x
x
x
x
x
x
x
Trouble Shooting
There is no power.
1. Plug machine in proper outlet.
2. If using two cords, make sure each is plugged into a separate circuit.
3. Check circuit breaker. Reset circuit breaker, other items should not run
on the same circuit as the machine. Outlet must be a 20-amp circuit.
Pump does not work properly
1. Snap quick disconnects firmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and flush clean.
4. Filters clogged, remove filters and rinse clean with water.
5. Heater is blocked; flush out with Mytee’s® System Maintainer.
6. If brass check valve is stuck, replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate may need to be replaced.
9. If pump motor brushes are worn, replace pump.
1001DX, 1001DX-200 or 1003DX heater does not work properly
1. If sensor mounted on the heater has popped, reset sensor by pushing
in button.
2. Heating element may need to be replaced.
Vacuum motor does not work properly
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Secure the vacuum tank tightly.
4. If ball float is shut off, empty vacuum tank of all wastewater.
5. Make sure ball float is firmly installed on the elbow.
6. If water is coming out of the vacuum motor, use a low foaming
detergent.
7. Clean upholstery tool or floor wand jets.
28
GENERAL INFORMATION
FAQs
HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME
FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE
SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY
BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT
NOTICE.
Q: How much do the Speedster® Series extractors weigh and what are
the dimensions?
A: All Speedsters
Machine Dimensions: 28” x 18 ¼” x 40”
Shipping Dimensions: 29 ½” x 19 ¼” x 46 ½”
1000DX – Machine Weight: 83 lbs.
Shipping Weight: 104 lbs.
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR
REPAIR OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE
REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER
EXPRESS OR IMPLIED. IN NO EVENT SHALL MYTEE BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY
DAMAGES, OR PERSONAL INJURIES.
1000DX-200 – Machine Weight: 83 lbs.
Shipping Weight: 104 lbs.
1001DX – Machine Weight: 94 lbs.
Shipping Weight: 124 lbs.
All limited warranties are void for, and Mytee does not warrant in any way,
any product that evidences misapplication, improper installation, abuse,
lack of maintenance, negligence in use or care, abnormal use, alteration
of design, modification, use of incompatible or corrosive chemicals, use in
a rental service, and/or servicing, installation of parts, or repairs by anyone
other than Mytee or a Mytee authorized distributor or service center. Mytee
may make changes in products it manufactures and markets at any time;
these changes are made without obligation to change, retrofit, or upgrade
any product previously sold or manufactured.
1001DX-200 – Machine Weight: 94 lbs.
Shipping Weight: 124 lbs.
1003DX – Machine Weight: 122 lbs.
Shipping Weight: 150 lbs.
1005DX – Machine Weight: 113 lbs.
Shipping Weight: 140 lbs.
Mytee has no obligation to honor the limited warranties set forth herein
unless the original purchaser, promptly upon discovering the warranty
claim and prior to continuing to use the product, contacts Mytee or a
Mytee authorized distributor or service center to describe the claim and to
receive and follow instructions for documenting and resolving the claim.
In addition, the purchaser must provide the product to which the claim
applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection. In addition, the purchaser must provide/return the
product intact, unmodified, with all of its original parts.
Q: What comes standard with Speedsters™ extractors?
A: Hose hanger with four screws, two Cuff-Lynx™ Model Numbers: H141
Reducer and H110 Coupler Swivel, and 45˚ drain elbow.
Q: Does Mytee® recommend tools for this machine?
A: All upholstery tools and wands can be used with the Speedster® series.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow
excess moisture in the vacs to dry off. You should also run Mytee’s®
System Maintainer through the system to keep the hoses, pump, and
heater clean and free of debris..
If any provision or portion of this limited warranty policy is found to be
unenforceable, then the remaining provisions and portions shall remain
valid and enforceable. If any provision or portion of this limited warranty
policy is found to be limited by law, then that provision or portion shall
be construed to make it effective within the bounds of law. For example,
if there are legal limitations on the duration of warranties, the warranties
made herein shall be construed to have the minimum duration required by
law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible
without violating the law.
Warranty
MYTEE LIFETIME LIMITED WARRANTY POLICY
Mytee Products, Inc. endeavors to provide high quality products and
product support to its customers and therefore backs up all of its new
products purchased from Mytee Products Inc. (“Mytee”) or any authorized
Mytee distributor/service center with this lifetime limited warranty. This
limited warranty begins on the date of the customer’s purchase and is
valid and available to the original purchaser with proof of purchase, and is
not transferable. Mytee’s products are for commercial use only and are not
intended for personal, family or household uses.
The validity, construction and performance of this warranty policy shall be
governed by the laws of the State of California, without respect to conflicts
of laws principles. The exclusive jurisdiction of any legal action arising
from or related to this warranty policy shall be in the State of California and
no legal action shall be commenced elsewhere.
HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that
its rotationally-molded housings will be free from manufacturing defects.
This warranty covers the cost of replacement or repair only and does not
cover shipping or labor costs.
Return Material Authorization Procedure
It is the responsibility of any Authorized Service Center (ASC) or Distributor with written authorization to ensure the Customers equipment is
repaired as soon as possible. Only Mytee Products Inc. or it’s authorized
dealers with written authorization, service centers, and agents may make
warranty repairs on these products. All others do so at their own risk and
expense.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear
parts for 90 days from the date of original purchase. “Wear parts” are
items which wear out as a result of usage or the passage of time and are
consumed despite attempts to maintain them, such as gaskets, wheels,
brass, cords, wires, electrical terminals, hoses, switches, thermostats,
plastisol parts, filters, bearings, brushes, solenoids, o-rings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s sole
discretion. This warranty covers the cost of replacement only and does not
cover shipping or labor costs.
The Distributor must follow Mytee Products, Inc. standard RMA procedure:
1. When a repair falls within the Warranty time period for a piece of equipment, the Distributor will fill out a RMA/Warranty claim form. This form will
act as a repair order to replace any defective parts.
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO
WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE,
PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY
GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
2. All defective parts must be returned to Mytee Products, Inc. with the
RMA/claim form for evaluation at the customer’s expense. This shipping is
non-refundable. All warranty claims are subject to an evaluation by Mytee
Products, Inc. to determine if warranty will be approved. Any credit for
29
repair and/or parts will only be issued upon evaluation and approval from
Mytee Products, Inc.
3. When Warranty is approved, the Distributor’s account will be credited
for the replacement part(s). Mytee Products, Inc. will ship the warranted
replacement part(s) to the Distributor prepaid. If Warranty is denied the
Distributor’s account will not be credited for any parts sent for this claim.
NOTES
Mytee Products Inc.
13655 Stowe Dr.
Poway, Ca. 92064
www.mytee.com
PH 858.679.1191
F X 858.679.7814
© 2012 Mytee Products Inc.
Printed in the U.S.A.
30