Download HP Pavilion DV6000t System information

HP Pavilion dv6000 Entertainment PC
Maintenance and Service Guide
© Copyright 2007 Hewlett-Packard
Development Company, L.P.
Bluetooth is a trademark owned by its
proprietor and used by Hewlett-Packard
Company under license. Intel and Core are
trademarks or registered trademarks of Intel
Corporation or its subsidiaries in the United
States and other countries. Microsoft,
Windows, and Windows Vista are either
trademarks or registered trademarks of
Microsoft Corporation in the United States
and/or other countries. SD Logo is a
trademark of its proprietor.
The information contained herein is subject to
change without notice. The only warranties
for HP products and services are set forth in
the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
First Edition: April 2007
Document Part Number: 443406-001
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC
adapter comply with the user-accessible surface temperature limits defined by the International Standard
for Safety of Information Technology Equipment (IEC 60950).
ENWW
iii
iv
Safety warning notice
ENWW
Table of contents
1 Product description
2 External component identification
Display components ................................................................................................................. 5
Top components ...................................................................................................................... 6
Lights ....................................................................................................................... 6
Buttons, speakers, and fingerprint reader ..................................................................... 7
Keys ........................................................................................................................ 9
TouchPad ............................................................................................................... 10
Front components ................................................................................................................... 11
Right-side components ............................................................................................................ 12
Rear component ..................................................................................................................... 13
Left-side components ............................................................................................................... 13
Bottom components ................................................................................................................ 15
3 Illustrated parts catalog
Serial number location ............................................................................................................ 17
Computer major components ................................................................................................... 18
Display assembly components ................................................................................................. 22
Plastics Kit ............................................................................................................................. 23
Cable Kit .............................................................................................................................. 24
Mass storage devices ............................................................................................................. 25
Miscellaneous parts ................................................................................................................ 26
Sequential part number listing .................................................................................................. 27
4 Removal and replacement procedures
Preliminary replacement requirements ....................................................................................... 33
Tools required ......................................................................................................... 33
Service considerations ............................................................................................. 33
Plastic parts ............................................................................................. 33
Cables and connectors ............................................................................. 34
Drive handling ......................................................................................... 34
Grounding guidelines .............................................................................................. 35
Electrostatic discharge damage .................................................................. 35
Packaging and transporting guidelines ........................................ 36
Workstation guidelines .............................................................. 36
Equipment guidelines ................................................................. 37
Unknown user password .......................................................................................... 38
ENWW
v
Component replacement procedures ........................................................................................ 39
Serial number ......................................................................................................... 39
Battery ................................................................................................................... 40
Camera module ...................................................................................................... 41
Display inverter ....................................................................................................... 43
Hard drive ............................................................................................................. 45
Computer feet ......................................................................................................... 47
Memory module ...................................................................................................... 47
RTC battery ............................................................................................................ 49
WLAN module ........................................................................................................ 50
Optical drive .......................................................................................................... 52
Switch cover ........................................................................................................... 54
Speaker assembly ................................................................................................... 56
Power button board ................................................................................................. 57
Keyboard ............................................................................................................... 58
Display assembly .................................................................................................... 61
Top cover ............................................................................................................... 66
Bluetooth module .................................................................................................... 70
ExpressCard assembly ............................................................................................. 71
USB/power connector board .................................................................................... 73
System board ......................................................................................................... 74
Audio board ........................................................................................................... 77
Fan/heat sink assembly ........................................................................................... 78
Processor ............................................................................................................... 80
5 Setup Utility
Starting the Setup Utility .......................................................................................................... 83
Changing the language of the Setup Utility ............................................................................... 83
Navigating and selecting in the Setup Utility .............................................................................. 84
Displaying system information .................................................................................................. 84
Restoring default settings in the Setup Utility .............................................................................. 84
Using advanced Setup Utility features ....................................................................................... 85
Closing the Setup Utility .......................................................................................................... 85
Setup Utility menus ................................................................................................................. 85
6 Specifications
Computer specifications .......................................................................................................... 87
15.4-inch, WXGA, BrightView display specifications ................................................................. 88
Hard drive specifications ........................................................................................................ 89
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive specifications ................................ 90
System DMA specifications ...................................................................................................... 91
System interrupt specifications ................................................................................................. 92
System I/O address specifications ............................................................................................ 93
System memory map specifications .......................................................................................... 95
7 Screw listing
Phillips PM2.0×5.0 captive screw ............................................................................................ 98
Phillips PM3.0×4.0 screw ....................................................................................................... 99
Phillips PM2.0×3.0 screw ..................................................................................................... 100
vi
ENWW
Phillips PM2.5×7.0 screw ..................................................................................................... 102
Phillips PM2.5×5.0 screw ..................................................................................................... 105
Phillips PM2.5×2.0 screw ..................................................................................................... 107
Phillips PM2.5×4.0 screw ..................................................................................................... 108
Hex HM5.0×9.0 standoff ..................................................................................................... 110
Phillips PM2.0×2.0 screw ..................................................................................................... 111
Phillips PM2.5×5.0 captive screw .......................................................................................... 112
Phillips 2.5×4.0 captive screw ............................................................................................... 113
8 Backup and Recovery
Recovering system information ............................................................................................... 115
Backing up your information ................................................................................... 115
When to back up ................................................................................... 115
Back up suggestions ............................................................................... 116
Using system restore points ..................................................................................... 116
When to create restore points .................................................................. 116
Create a system restore point ................................................................... 116
Restore to a previous date and time .......................................................... 117
Creating recovery discs ......................................................................................... 117
Reinstalling software programs and drivers ............................................................... 118
Reinstalling preinstalled programs and drivers ........................................... 118
Reinstalling programs from discs .............................................................. 118
Performing a recovery ........................................................................................... 119
Recovering from the recovery discs ........................................................... 119
Recovering from the partition on the hard drive .......................................... 119
Deleting the recovery partition on the hard drive ....................................................... 120
Updating reinstalled software ................................................................................. 120
9 Connector pin assignments
Audio-in (microphone) ..........................................................................................................
Audio-out (headphone) .........................................................................................................
External monitor ...................................................................................................................
RJ-11 (modem) .....................................................................................................................
RJ-45 (network) ....................................................................................................................
S-Video-out ..........................................................................................................................
Universal Serial Bus ..............................................................................................................
121
121
122
123
123
124
124
10 Power cord set requirements
Requirements for all countries or regions ................................................................................. 125
Requirements for specific countries or regions .......................................................................... 126
11 Recycling
Battery ................................................................................................................................ 127
Display ............................................................................................................................... 127
Index ............................................................................................................................... 133
ENWW
vii
viii
ENWW
1
Product description
Category
Description
Fullfeatured
models
Defeatured
models
Product Name
HP Pavilion dv6000 Entertainment PC
√
√
Processors
Intel® dual-core 64-bit processor with 800-MHz front
side bus
√
√
√
√
Graphics
√
Intel Extreme Graphics (Mobile Intel Graphics Media
Accelerator X3100) UMA (integrated) with shared video memory, up
to 64 MB on computer models equipped with 512 MB of system
random access memory (RAM), or up to 256 MB on computer models
equipped with 1024 MB or more of system RAM (memory size is
dynamic change)
√
Panels
15.4-inch, WXGA BrightView
√
√
Memory
●
Two SODIMM slots
√
√
●
Customer-accessible/upgradable
●
Supports up to 2 GB of system RAM
●
DDRII PC2-5300 (667-MHz)
√
√
Chipset
Hard drives
ENWW
●
Intel® Core™ Duo T7300 2.0-GHz processor (4 MB of L2
cache)
●
Intel Core Duo T7100 1.8-GHz processor (2 MB of L2 cache)
●
Intel GM965
●
Southbridge ICH8m
◦
2048 (1024 × 2)
◦
1536 (1024 + 512)
◦
1024 (1024 × 1, 512 × 2)
◦
512 (512 × 1)
●
Serial ATA
●
Supports all 9.5-mm, 2.5-inch hard drives, including the
following:
◦
200-GB, 4200-rpm
◦
160-GB, 5400-rpm
◦
120-GB, 5400-rpm
1
Category
Optical drives
◦
80-GB, 5400-rpm
◦
60-GB, 5400-rpm
●
12.7-mm tray load
●
Fixed (removal of 1 screw required)
●
Parallel ATA
●
Supports the following drives:
◦
DVD±RW and CD-RW Super Multi Double-Layer Combo
Drive with LightScribe
◦
DVD±RW and CD-RW Super Multi Double-Layer Combo
Drive
◦
DVD/CD-RW Combo Drive
Fullfeatured
models
Defeatured
models
√
√
√
Diskette drive
Supports external USB drive only
√
Camera
1.3-megapixel, low-light, VGA camera - fixed (no tilt)
√
Microphone
2 omnidirectional, dual-array microphones, with beam-forming,
echo-cancellation, noise-suppression software
√
Audio
●
HD audio - Realtek ALC861-VD-GR
●
Supports Microsoft® Premium requirements
●
Pavilion-branded Altec Lansing speakers
●
56K V.92 data/fax modem (SilonLab ML3000)
●
Supports all worldwide certification requirements
●
Modem cable not included
●
Integrated Realtek 10/100 network interface card (NIC)
●
Ethernet cable not included
Modem
Ethernet
Wireless
External media
card
Ports
2
Description
Integrated wireless local area network (WLAN) options
by way of wireless module:
√
√
√
√
√
√
√
√
√
●
Intel PRO Wireless 3945 802.11a/b/g and 802.11b/g with
2 antennae integrated into the display assembly
●
Intel PRO Wireless 4965 802.11a/b/g/n with 3 antennae
integrated into the display assembly
●
Intel WLAN + Bluetooth®
●
One ExpressCard54 slot
√
●
5-in-1 Digital Media Slot, supports SD, MMC, SDIO, MS,
MSpro, xD
√
●
Audio-in jack (mono microphone)
√
√
●
Audio-out jack (stereo headphone)
√
√
Chapter 1 Product description
ENWW
Category
Description
Audio-out jack (stereo headphone with S/PDIF)
√
●
RJ-11 jack (modem)
√
√
●
RJ-45 jack (Ethernet, includes link and activity lights)
√
√
●
S-Video-out jack
√
√
●
USB ports (3)
√
●
USB ports (2)
●
VGA port (Dsub 15-pin)
√
●
1394 port
√
●
2-pin AC power connector
√
√
√
√
√
√
√
√
√
√
√
Expansion port 3 supports HP xb3000 Notebook Expansion Base
and HP Notebook QuickDock
Keyboard/pointing
devices
●
15.4-inch keyboard
●
TouchPad with 2 buttons and two-way scroll (taps enabled as
default)
Power
requirements
●
12-cell 2.20-Ah Li-ion battery
●
6-cell 2.55-Ah Li-ion battery
●
6-cell 2.20-Ah Li-ion battery
65-W AC adapter with localized cable plug support (2-wire plug
with ground pin, supports 2-pin DC connector)
Operating system
Serviceability
ENWW
Defeatured
models
●
Docking
Security
Fullfeatured
models
√
●
Security cable slot
√
●
Fingerprint reader
√
Preinstalled:
●
Windows Vista™ Business (32-bit)
●
Windows Vista Ultimate (64-bit)
●
Windows Vista Premium (32- and 64-bit)
●
Windows Vista Home Basic (32-bit)
End-user replaceable parts:
●
AC adapter
●
Battery (system)
●
Hard drive
●
Memory module
●
Optical drive
●
WLAN module
√
√
√
√
√
3
4
Chapter 1 Product description
ENWW
2
External component identification
Display components
Item
Component
Description
(1)
Internal display switch*
Turns off the display if the display is closed while the
computer is on.
(2)
Internal microphones (2) (select models only)
Record sound.
NOTE: If there is a microphone icon next to each
microphone opening, the computer has internal
microphones.
(3)
Integrated camera light (select models only)
On: The integrated camera is in use.
(4)
Integrated camera (select models only)
Records video and captures still photographs.
*The location of the internal display switch varies by computer model.
ENWW
Display components
5
Top components
Lights
Item
Component
Description
(1)
Power lights (2)*
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
●
On: A battery is charging.
●
Blinking: A battery that is the only available power
source has reached a low battery level or a critical
battery level.
●
Off: If the computer is plugged into an external power
source, the light is turned off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light stays
off until the battery reaches a low battery level.
(2)
Battery light
(3)
Drive light
Blinking: The hard drive or optical drive is being accessed.
(4)
Caps lock light
On: Caps lock is on.
(5)
Volume mute light
●
Blue: Computer sound is turned on.
●
Amber: Computer sound is turned off.
(6)
Volume down light
Blinking: The volume scroll zone is being used to decrease
speaker volume.
(7)
Volume up light
Blinking: The volume scroll zone is being used to increase
speaker volume.
(8)
Num lock light
On: Num lock is on or the embedded numeric keypad is
enabled.
*The 2 power lights display the same information. The light on the power button is visible only when the computer is open. The
power light on the front of the computer is visible whether the computer is open or closed.
6
Chapter 2 External component identification
ENWW
Buttons, speakers, and fingerprint reader
Item
Component
Description
(1)
Power button*
●
When the computer is off, press the button to turn on
the computer.
●
When the computer is on, press the button to shut down
the computer.
●
When the computer is in the Sleep state, press the
button briefly to exit Sleep.
●
When the computer is in Hibernation, press the button
briefly to exit Hibernation.
If the computer has stopped responding and Windows®
shutdown procedures are ineffective, press and hold the
power button for at least 5 seconds to turn off the computer.
To learn more about power settings, select Start > Control
Panel > System and Maintenance > Power
Options.
(2)
Speakers (2)
Produce sound.
(3)
Media button
Opens the QuickPlay program.
NOTE: If the computer has been set up to require a logon
password, you may be asked to log on to Windows.
QuickPlay opens after you log on. Refer to the QuickPlay
software Help for more information.
(4)
DVD button
Opens the DVD playback feature of the QuickPlay program.
NOTE: If the computer has been set up to require a logon
password, you may be asked to log on to Windows.
QuickPlay opens after you log on. Refer to the QuickPlay
software Help for more information.
(5)
ENWW
Previous/rewind button
●
Plays the previous track or chapter when pressed once.
●
Rewinds media when pressed simultaneously with
the fn key.
Top components
7
Item
Component
Description
(6)
Play/pause button
Plays or pauses the disc.
(7)
Next/fast forward button
●
Plays the next track or chapter when pressed once.
●
Fast forwards media when pressed simultaneously with
the fn key.
(8)
Stop button
Stops the disc.
(9)
Volume mute button
Mutes and restores the speaker sound.
(10)
Volume scroll zone
Adjusts speaker volume. Slide your finger to the left to
decrease volume and to the right to increase volume. You
can also tap the minus sign on the scroll zone to decrease
volume, or tap the plus sign on the scroll zone to increase
volume.
(11)
Fingerprint reader (select models only)
Allows a fingerprint logon to Windows, instead of a
password logon.
*This table describes factory settings. For information about changing factory settings, refer to the user guides located in Help
and Support.
8
Chapter 2 External component identification
ENWW
Keys
ENWW
Item
Component
Function
(1)
esc key
Displays system information when pressed in combination
with the fn key.
(2)
fn key
Executes frequently used system functions when pressed in
combination with a function key or the esc key.
(3)
Windows logo key
Displays the Windows® Start menu.
(4)
Windows applications key
Displays a shortcut menu for items beneath the pointer.
(5)
Embedded numeric keypad keys
Can be used like the keys on an external numeric keypad.
(6)
Function keys
Execute frequently used system functions when pressed in
combination with the fn key.
Top components
9
TouchPad
Item
Component
Function
(1)
TouchPad light
●
Blue: TouchPad is enabled.
●
Amber: TouchPad is disabled.
(2)
TouchPad*
Moves the pointer and selects or activates items on the
screen.
(3)
Left TouchPad button*
Functions like the left button on an external mouse.
(4)
TouchPad on/off button
Enables/disables the TouchPad.
(5)
TouchPad scroll zone
Scrolls up or down.
(6)
Right TouchPad button*
Functions like the right button on an external mouse.
*This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel >
Hardware and Sound > Mouse.
10
Chapter 2 External component identification
ENWW
Front components
Item
Component
Function
(1)
Power light
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
●
On: A battery is charging.
●
Blinking: A battery that is the only available power
source has reached a low battery level or a critical
battery level.
●
Off: If the computer is plugged into an external power
source, the light is turned off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light stays
off until the battery reaches a low battery level.
(2)
Battery light
(3)
Drive light
Blinking: The hard drive or optical drive is being accessed.
(4)
Wireless switch
Turns the wireless feature on or off, but does not create a
wireless connection.
NOTE: To establish a wireless connection, a wireless
network must already be set up.
(5)
ENWW
Wireless light
●
Blue: An integrated wireless device, such as a WLAN
device and/or a Bluetooth® device, is turned on.
●
Amber: An integrated wireless device is turned off.
(6)
Consumer infrared lens
Receives a signal from a remote control device, such as the
HP Remote Control.
(7)
Audio-in (microphone) jack
Connects an optional computer headset microphone, stereo
array microphone, or monaural microphone.
(8)
Audio-out (headphone) jack
Produces sound when connected to optional powered stereo
speakers, headphones, ear buds, a headset, or television
audio.
(9)
Audio-out (headphone) S/PDIF jack (select models
only)
Produces sound when connected to optional powered stereo
speakers, headphones, ear buds, a headset, or television
audio.
Front components
11
Right-side components
12
Item
Component
Function
(1)
ExpressCard slot
Supports optional ExpressCard/54 cards.
(2)
Optical drive
Reads optical discs, and, on select models, also writes to
optical discs.
(3)
Optical drive light
Blinking: The optical drive is being accessed.
(4)
USB port (select models only)
Connects an optional USB device.
(5)
Power connector
Connects an AC adapter.
Chapter 2 External component identification
ENWW
Rear component
Component
Description
Vent
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
Left-side components
Item
Component
Function
(1)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from being
mishandled or stolen.
(2)
S-Video-out jack
Connects an optional S-Video device such as a television,
VCR, camcorder, overhead projector, or video capture
card.
(3)
External monitor port
Connects an external VGA monitor or projector.
(4)
Expansion port 3
Connects the computer to an optional docking device or
expansion product.
NOTE: The computer has only one expansion port. The
term expansion port 3 describes the type of expansion port.
(5)
RJ-45 (network) jack
Connects a network cable.
NOTE: On select computer models, the network jack
provides Gigabit Ethernet functionality.
ENWW
(6)
RJ-11 (modem) jack
Connects a modem cable.
(7)
HDMI port (select models only)
Connects an optional video or audio device such as a highdefinition television, set-top box, DVD player, or any
compatible digital or audio device.
(8)
USB ports (1 or 2, depending on computer model)
Connect optional USB devices.
Rear component
13
14
Item
Component
Function
(9)
1394 port (select models only)
Connects an optional IEEE 1394 or 1394a device, such as
a camcorder.
(10)
Digital Media Slot light (select models only)
On: A digital card is being accessed.
(11)
Digital Media Slot (select models only)
Supports the following optional digital card formats:
Chapter 2 External component identification
●
Memory Stick (MS)
●
Memory Stick Pro (MSP)
●
MultiMediaCard (MMC)
●
Secure Digital Input/Output (SD I/O)
●
Secure Digital (SD) Memory Card
●
xD-Picture Card (XD)
●
xD-Picture Card (XD) Type H
●
xD-Picture Card (XD) Type M
ENWW
Bottom components
Item
Component
Function
(1)
Battery bay
Holds the battery.
(2)
Battery release latch
Releases the battery from the battery bay.
(3)
Vents (5)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(4)
Memory/WLAN module compartment
Contains the memory module slots, the WLAN module slot,
and the RTC battery.
CAUTION: To prevent an unresponsive system, replace
the wireless module only with a wireless module authorized
for use in the computer by the governmental agency that
regulates wireless devices in your country or region. If you
replace the module and then receive a warning message,
remove the module to restore computer functionality, and
then contact technical support through Help and Support.
(5)
ENWW
Hard drive bay
Holds the hard drive.
Bottom components
15
16
Chapter 2 External component identification
ENWW
3
Illustrated parts catalog
Serial number location
When ordering parts or requesting information, provide the computer serial number and model number
located on the bottom of the computer.
ENWW
Serial number location
17
Computer major components
18
Item
Description
(1)
Display assemblies
Chapter 3 Illustrated parts catalog
Spare part number
ENWW
Item
Description
Spare part number
15.4-inch, WXGA, BrightView, display assembly for use only with computer models equipped
with a camera (includes camera, microphones, and WLAN transceivers and antenna cables)
446481-001
15.4-inch, WXGA, BrightView, display assembly for use only with computer models not
equipped with a camera (includes microphones and WLAN transceivers and antenna cables)
446482-001
NOTE:
(2)
Switch cover (includes LED board and cable)
446512-001
(3)
Power button board (includes power button board cable)
441437-001
(4)
Keyboards
(5)
ENWW
See Display assembly components on page 22 for more information on display assembly spare part numbers.
Belgium
441427-A41
The Czech Republic
441427-221
Denmark
441427-081
Finland, Norway, and Sweden
441427-DH1
France
441427-051
French Canada
441427-121
Germany
441427-041
Greece
441427-151
Israel
441427-BB1
Italy
441427-061
Japan
441427-291
Korea
441427-AD1
The Netherlands and Europe
441427-B31
Portugal
441427-131
Russia
441427-251
Saudi Arabia
441427-171
Spain
441427-071
Switzerland
441427-111
Taiwan
441427-AB1
Thailand
441427-281
Turkey
441427-141
The United Kingdom
441427-031
The United States
441427-001
Top covers (include TouchPad and cable)
For use only with computer models equipped with a fingerprint reader (includes fingerprint
reader board and cable)
446509-001
For use only with models not equipped with a fingerprint reader
446508-001
Computer major components
19
Item
Description
Spare part number
Fingerprint reader board (not illustrated; includes fingerprint reader board cable)
446511-001
(6)
Speaker assembly
431447-001
(7)
Top cover trim
431421-001
(8)
Fan/heat sink assembly (includes thermal pads)
446521-001
Plastics Kit (see Plastics Kit on page 23 for more Plastics Kit component information):
438368-001
(9a)
ExpressCard slot bezel
(9b)
Hard drive cover (includes 2 captive screws, secured by C-clips)
(9c)
Memory/WLAN module compartment cover (includes 2 captive screws, secured by C-clips)
HDMI port cover (not illustrated)
(10)
ExpressCard assembly
(11)
Processors
431439-001
Intel Core Duo T7300 (2.0-GHz, 4 MB of L2 cache)
446478-001
Intel Core Duo T7100 (1.8-GHz, 2 MB of L2 cache)
446479-001
(12)
System board (includes modem cable)
446477-001
(13)
Bluetooth module (includes Bluetooth module cable)
412766-002
(14)
USB/power connector board (includes USB/power connector board cable)
449454-001
(15)
Audio board (includes infrared lens and audio board cable)
446523-001
(16)
Base enclosure (includes wireless on/off switch)
446513-001
Rubber Kit (not illustrated; includes base enclosure rubber feet and display bezel screw
covers)
431430-001
(17)
(18)
(19)
Batteries
12-cell, 8.80-Ah
432307-001
6-cell, 2.55-Ah
446507-001
6-cell, 2.20-Ah
446506-001
Hard drives (include hard drive bracket and hard drive connector)
200-GB, 4200-rpm
441424-001
160-GB, 5400-rpm
438485-001
120-GB, 5400-rpm
446498-001
80-GB, 5400-rpm
446497-001
60-GB, 5400-rpm
446496-001
WLAN modules
802.11a/b/g/n WLAN modules:
●
20
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India,
Chapter 3 Illustrated parts catalog
441086-001
ENWW
Item
Description
Spare part number
Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan,
Uruguay, the United States, Venezuela, and Vietnam
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the
Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
441087-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South
Korea
441088-003
●
For use in Japan
441089-291
802.11a/b/g WLAN modules:
For use in Antigua & Barbuda, Argentina, Australia, the Bahamas, Barbados, Brunei,
Canada, Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India,
Indonesia, Malaysia, Mexico, New Zealand, Panama, Paraguay, Saudi Arabia,
Taiwan, the United States, and Vietnam
●
For use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda, Brazil, Bulgaria, the 407674-002
Cayman Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El
Salvador, Estonia, Finland, France, Georgia, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Jordan, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri
Lanka, Sweden, Switzerland, Turkey, the United Kingdom, and Uzbekistan
●
For use in Ecuador, Haiti, Honduras, Pakistan, the People's Republic of China, Peru,
Qatar, South Korea, Uruguay, and Venezuela
407674-003
●
For use in Japan
407674-291
802.11b/g WLAN module for use in Thailand
407674-004
(20)
RTC battery (includes 2-sided tape)
446518-001
(21)
Memory modules (667-MHz, PC2-5300, 1-DIMM)
(22)
ENWW
407674-001
●
1024-MB
446495-001
512-MB
446494-001
Optical drives (include bezel)
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
446501-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
446500-001
DVD/CD-RW Combo Drive
446499-001
Cable Kit (not illustrated; see Cable Kit on page 24 for more Cable Kit component
information)
446519-001
Computer major components
21
Display assembly components
22
Item
Description
(1)
Display bezels
Spare part number
For use only with computer models equipped with a camera (includes openings for camera
and microphones)
446483-001
For use only with computer models not equipped with a camera (includes openings for
microphones)
446484-001
(2)
Display Hinge Kit (includes left and right display hinges)
431395-001
(3)
Display inverter (includes Mylar shield)
431391-001
(4)
Camera module (includes 2-sided tape)
446486-001
(5)
Display panel (15.4-inch, WXGA, BrightView; includes display panel cable and camera
cable)
446480-001
(6)
Wireless Antenna Kits
For use only with computer models equipped with an 802.11a/b/g/n WLAN module
(includes 3 transceivers and cables)
449727-001
For use only with computer models equipped with an 802.11a/b/g or 802.11b/g WLAN
module (includes 2 transceivers and cables)
431398-001
(7)
Microphone
431393-001
(8)
Display Cable Kit (includes camera module cable)
446489-001
(9)
Display enclosure (includes logo and WLAN wireless antenna transceivers and cables)
446487-001
Display hinge covers (not illustrated)
431396-001
Chapter 3 Illustrated parts catalog
ENWW
Item
Description
Spare part number
Display Label Kit (not illustrated)
446525-001
Display Screw Kit (not illustrated)
431399-001
Plastics Kit
Item
ENWW
Description
Spare part number
Plastics Kit:
438368-001
(1)
ExpressCard slot bezel
(2)
Hard drive cover (includes 2 captive screws, secured by C-clips)
(3)
Memory/WLAN module compartment cover (includes 2 captive screws, secured by C-clips)
Plastics Kit
23
Cable Kit
Item
24
Description
Spare part number
Cable Kit:
446519-001
(1)
LED board cable
(2)
Power button board cable
(3)
USB/power connector board cable
(4)
Audio board cable
(5)
Bluetooth module cable
Chapter 3 Illustrated parts catalog
ENWW
Mass storage devices
Item
Description
(1)
Hard drives (include hard drive bracket)
(2)
ENWW
Spare part number
200-GB, 4200-rpm
441424-001
160-GB, 5400-rpm
438485-001
120-GB, 5400-rpm
446498-001
80-GB, 5400-rpm
446497-001
60-GB, 5400-rpm
446496-001
Optical drives (include bezel and bracket)
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
446501-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
446500-001
DVD/CD-RW Combo Drive
446499-001
Mass storage devices
25
Miscellaneous parts
Description
Spare part number
65W AC adapter
402018-001
ATSC/NTSC TV tuner antenna
439131-001
ATSC/NTSC/PAL TV tuner
439130-001
Composite video cable
407939-001
DVB-T tuner
412175-001
DVB-T antenna adapter
412176-001
ExpressCard Kit (includes software CD)
445170-001
HP backpack
405527-001
HP carrying case
418162-001
HP Remote Control
435743-001
Infrared emitter with cable
439129-001
Optical wired mouse
436238-001
RF input adapter cable (without ferrite)
407940-001
USB digital drive
364727-002
Vista remote control (fits into ExpressCard slot)
439128-001
Vista remote control (does not fit into ExpressCard slot)
439254-001
Wired headset
371693-001
Wireless laser mouse with cable adapter
430958-001
Power cords:
Australia and New Zealand
394279-011
Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway, Portugal, Spain, and 394279-021
Sweden
26
Canada, French Canada, Latin America, Thailand, and the United States
394279-001
Denmark
394279-081
India
394279-D61
Israel
394279-BB1
Italy
394279-061
Japan
394279-291
Korea
394279-AD1
The People's Republic of China
394279-AA1
Switzerland
394279-111
Taiwan
394279-AB1
Chapter 3 Illustrated parts catalog
ENWW
Description
Spare part number
The United Kingdom and Hong Kong
394279-031
Screw Kit
434747-001
●
Hex HM5.0×9.0 standoff
●
Phillips PM3.0×4.0 screw
●
Phillips PM2.5×7.0 screw
●
Phillips PM2.5×5.0 screw
●
Phillips PM2.5×5.0 captive screw
●
Phillips PM2.5×4.0 screw
●
Phillips PM2.5×4.0 captive screw
●
Phillips PM2.5×2.0 screw
●
Phillips PM2.0×5.0 captive screw
●
Phillips PM2.0×3.0 screw
●
Phillips PM2.0×2.0 screw
Sequential part number listing
ENWW
Spare part
number
Description
364727-002
USB digital drive
371693-001
Wired headset with volume control
394279-001
Power cord for use in the United States
394279-011
Power cord for use in Australia
394279-021
Power cord for use in Europe
394279-031
Power cord for use in the United Kingdom
394279-061
Power cord for use in Italy
394279-081
Power cord for use in Denmark
394279-111
Power cord for use in Switzerland
394279-291
Power cord for use in Japan
394279-AA1
Power cord for use in the People's Republic of China
394279-AB1
Power cord for use in Taiwan
394279-AD1
Power cord for use in Korea
394279-BB1
Power cord for use in Israel
394279-D61
Power cord for use in India
402018-001
65-watt AC adapter
Sequential part number listing
27
28
Spare part
number
Description
405527-001
HP backpack
407674-001
802.11a/b/g WLAN module for use in Antigua & Barbuda, Argentina, Australia, the Bahamas,
Barbados, Brunei, Canada, Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India,
Indonesia, Malaysia, Mexico, New Zealand, Panama, Paraguay, Saudi Arabia, Taiwan, the United
States, and Vietnam
407674-002
802.11a/b/g WLAN module for use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda, Brazil,
Bulgaria, the Cayman Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El
Salvador, Estonia, Finland, France, Georgia, Germany, Greece, Hungary, Iceland, Ireland, Italy, Jordan,
Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman,
the Philippines, Poland, Portugal, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, the United Kingdom, and
Uzbekistan
407674-003
802.11a/b/g WLAN module for use in Ecuador, Haiti, Honduras, Pakistan, the People's Republic of
China, Peru, Qatar, South Korea, Uruguay, and Venezuela
407674-004
802.11b/g WLAN module for use in Thailand
407674-291
802.11a/b/g WLAN module for use in Japan
407939-001
Composite video cable
407940-001
RF input adapter cable (without ferrite)
412175-001
DVB-T tuner
412176-001
DVB-T antenna adapter
412766-002
Bluetooth module (includes Bluetooth module cable)
418162-001
HP carrying case
430958-001
Wireless laser mouse (includes cable adapter)
431391-001
Display inverter
431393-001
Microphone (includes receiver and cable)
431395-001
Display Hinge Kit (includes left and right display hinges)
431396-001
Display Hinge Cover Kit
431398-001
Wireless Antenna Kit for use only with computer models equipped with an 802.11a/b/g or 802.11b/g
WLAN module (includes 2 transceivers and cables)
431399-001
Display Screw Kit
431421-001
Top cover trim
431430-001
Rubber Kit
431437-001
Power button board (includes power button board cable)
431439-001
ExpressCard assembly
431447-001
Speaker assembly
432307-001
12-cell, 8.8-Ah battery
434747-001
Screw Kit
435743-001
HP Remote Control
436238-001
Optical wired mouse
Chapter 3 Illustrated parts catalog
ENWW
ENWW
Spare part
number
Description
438368-001
Plastics Kit (see Plastics Kit on page 23 for more Plastics Kit component information)
438485-001
160-GB, 5400-rpm hard drive (includes hard drive bracket)
439128-001
Vista remote control (fits into ExpressCard slot)
439129-001
Infrared emitter with cable
439130-001
ATSC/NTSC/PAL TV tuner
439131-001
ATSC/NTSC TV tuner antenna
439254-001
Vista remote control (does not fit into ExpressCard slot)
441086-001
802.11a/b/g/n WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas,
Barbados, Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia,
Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States,
Venezuela, and Vietnam
441087-002
802.11a/b/g/n WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria,
Croatia, Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany,
Greece, Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg,
Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden,
Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
441088-003
802.11a/b/g/n WLAN module for use in Australia, New Zealand, Pakistan, the People's Republic of
China, and South Korea
441089-291
802.11a/b/g/n WLAN module for use in Japan
441424-001
200-GB, 4200-rpm hard drive (includes hard drive bracket)
441427-001
Keyboard for use in the United States
441427-031
Keyboard for use in the United Kingdom
441427-041
Keyboard for use in Germany
441427-051
Keyboard for use in France
441427-061
Keyboard for use in Italy
441427-071
Keyboard for use in Spain
441427-081
Keyboard for use in Denmark
441427-111
Keyboard for use in Switzerland
441427-121
Keyboard for use in French Canada
441427-131
Keyboard for use in Portugal
441427-141
Keyboard for use in Turkey
441427-151
Keyboard for use in Greece
441427-171
Keyboard for use in Saudi Arabia
441427-221
Keyboard for use in the Czech Republic
441427-251
Keyboard for use in Russia
441427-281
Keyboard for use in Thailand
Sequential part number listing
29
30
Spare part
number
Description
441427-291
Keyboard for use in Japan
441427-A41
Keyboard for use in Belgium
441427-AB1
Keyboard for use in Taiwan
441427-AD1
Keyboard for use in Korea
441427-B31
Keyboard for use in the Netherlands and Europe
441427-BB1
Keyboard for use in Israel
441427-DH1
Keyboard for use in Finland, Norway, and Sweden
445170-001
ExpressCard Kit (includes software CD)
446477-001
System board
446478-001
Intel Core Duo T7300 2.0-GHz processor (4 MB of L2 cache; includes thermal material)
446479-001
Intel Core Duo T7100 1.8-GHz, processor (2 MB of L2 cache; includes thermal material)
446480-001
15.4-inch, WXGA, BrightView display panel
446481-001
15.4-inch, WXGA, BrightView display assembly for use only with computer models equipped with a
camera
446482-001
15.4-inch, WXGA, BrightView display assembly for use only with computer models not equipped with a
camera
446483-001
Display bezel for use only with computer models equipped with a camera
446484-001
Display bezel for use only with computer models not equipped with a camera
446486-001
Camera module (includes 2-sided tape)
446487-001
Display enclosure
446489-001
Display Cable Kit
446494-001
512-MB memory module (667-MHz, PC2-5300, 1-DIMM)
446495-001
1024-MB memory module (667-MHz, PC2-5300, 1-DIMM)
446496-001
60-GB, 5400-rpm hard drive (includes hard drive bracket)
446497-001
80-GB, 5400-rpm hard drive (includes hard drive bracket)
446498-001
120-GB, 5400-rpm hard drive (includes hard drive bracket)
446499-001
DVD/CD-RW Combo Drive
446500-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
446501-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
446506-001
6-cell, 2.20-Ah battery
446507-001
6-cell, 2.55-Ah battery
446508-001
Top cover for use only with computer models not equipped with a fingerprint reader (includes TouchPad
and cable)
446509-001
Top cover for use only with computer models equipped with a fingerprint reader (includes TouchPad and
cable and fingerprint reader board and cable)
Chapter 3 Illustrated parts catalog
ENWW
ENWW
Spare part
number
Description
446511-001
Fingerprint reader board (includes fingerprint reader board cable)
446512-001
Switch cover (includes LED board and cable)
446513-001
Base enclosure (includes wireless switch actuator and infrared lens)
446518-001
RTC battery (includes 2-sided tape)
446519-001
Cable Kit (see Cable Kit on page 24 for more Cable Kit component information)
446521-001
Fan/heat sink assembly (include thermal pads)
446523-001
Audio board (includes audio connectors, audio board cable, and infrared lens)
446525-001
Display Label Kit
449454-001
USB/power connector board (includes USB/power connector board cable)
449727-001
Wireless Antenna Kit for use only with computer models equipped with an 802.11a/b/g/n WLAN module
(includes 3 transceivers and cables)
Sequential part number listing
31
32
Chapter 3 Illustrated parts catalog
ENWW
4
Removal and replacement
procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Flat-bladed screwdriver
●
Hex 5.0-mm nut driver
●
Magnetic screwdriver
●
Phillips P0 and P1 screwdrivers
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly
and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when
handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
ENWW
Preliminary replacement requirements
33
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme
care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer
is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be
sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
34
Chapter 4 Removal and replacement procedures
ENWW
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you area ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described in
this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
ENWW
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Preliminary replacement requirements
35
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to
avoid static charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
36
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Chapter 4 Removal and replacement procedures
ENWW
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can
be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm
resistance between the operator and ground. To be effective, the conductive strips must be worn in
contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
ENWW
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Preliminary replacement requirements
37
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the password.
NOTE: These steps also clear CMOS.
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the RTC battery (see RTC battery on page 49).
6.
Wait approximately 5 minutes.
7.
Replace the RTC battery and reassemble the computer.
8.
Connect AC power to the computer. Do not reinsert any batteries at this time.
9.
Turn on the computer.
All passwords and all CMOS settings have been cleared.
38
Chapter 4 Removal and replacement procedures
ENWW
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 83 screws and standoffs, in 12 different sizes, that must be removed, replaced, or
loosened when servicing the computer. Make special note of each screw and standoff size and location
during removal and replacement.
Serial number
Report the computer serial number to HP when requesting information or ordering spare parts. The serial
number is located on the bottom of the computer.
ENWW
Component replacement procedures
39
Battery
Description
Spare part number
12-cell, 8.80-Ah Li-ion battery
432307-001
6-cell, 2.55-Ah Li-ion battery
446507-001
6-cell, 2.20-Ah Li-ion battery
446506-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the battery:
1.
Turn the computer upside down on a flat surface.
2.
Slide the battery release latch (1) to release the battery.
3.
Pivot the battery (2) upward and remove it from the computer.
To insert the battery, insert the rear edge of the battery into the battery bay and pivot the battery downward
until it is seated. The battery release latch automatically locks the battery into place.
40
Chapter 4 Removal and replacement procedures
ENWW
Camera module
NOTE: If it has been determined that the camera module is the component that must be replaced to
complete the computer repair, the display assembly does not have to be removed. Follow the procedures
in this section to replace the camera module. For information on replacing the display assembly and other
display assembly internal components, see Display assembly on page 61.
Description
Spare part number
Camera module (includes 2-sided tape)
446486-001
Before removing the camera module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the camera module:
1.
Turn the computer display-side up, with the front toward you.
2.
Open the computer as far as possible.
3.
Remove the four rubber screw covers (1) on the display bezel top edge.
NOTE: The display rubber screw covers are included in the Display Screw Kit, spare part number
431399-001.
ENWW
4.
Remove the four Phillips PM2.5×5.0 screws (2) on the display bezel top edge.
5.
Flex the inside edges of the left and right sides (1) and the top edge (2) of the display bezel until
the bezel disengages from the display enclosure.
Component replacement procedures
41
6.
Release the display bezel top edge (3).
7.
Release the camera module (1) from the display enclosure as far as the camera module cable
allows.
8.
Disconnect the camera module cable (2) from the camera module.
NOTE: The camera module is available using spare part number 446486-001.
9.
Remove the camera module.
Reverse this procedure to install the camera module.
42
Chapter 4 Removal and replacement procedures
ENWW
Display inverter
NOTE: If it has been determined that the display inverter is the component that must be replaced to
complete the computer repair, the display assembly does not have to be removed. Follow the procedures
in this section to replace the display inverter. For information on replacing the display assembly and other
display assembly internal components, see Display assembly on page 61.
Description
Spare part number
Display inverter (includes 2-sided tape)
431391-001
Before removing the display inverter, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the display inverter:
1.
Turn the computer display-side up, with the front toward you.
2.
Open the computer as far as possible.
3.
Remove the two rubber screw covers (1) on the display bezel bottom edge.
NOTE: The display rubber screw covers are included in the Display Screw Kit, spare part number
431399-001.
ENWW
4.
Remove the two Phillips PM2.5×5.0 screws (2) that secure the display bezel bottom edge to the
display assembly.
5.
Flex the inside edges of the left and right sides (1) and the bottom edge (2) of the display bezel until
the bezel disengages from the display enclosure.
Component replacement procedures
43
6.
Release the display bezel bottom edge (3).
7.
Release the display inverter (1) as far as the display panel cable and the backlight cable allow.
8.
Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.
9.
Remove the display inverter.
Reverse this procedure to install the display inverter.
44
Chapter 4 Removal and replacement procedures
ENWW
Hard drive
NOTE:
All hard drive spare part kits include a hard drive bracket.
Description
Spare part number
200-GB, 4200-rpm
441424-001
160-GB, 5400-rpm
438485-001
120-GB, 5400-rpm
446498-001
80-GB, 5400-rpm
446497-001
60-GB, 5400-rpm
446496-001
Before removing the hard drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the hard drive:
1.
Position the computer with the front toward you.
2.
Loosen the two Phillips PM2.0×5.0 screws (1) that secure the hard drive cover to the computer.
3.
Lift the right side of the hard drive cover (2), swing it to left, and remove the cover.
NOTE: The hard drive cover is included in the Plastics Kit, spare part number 438368-001.
ENWW
Component replacement procedures
45
4.
Use the Mylar tab (1) to lift the hard drive (2) until it disconnects from the computer.
5.
Remove the hard drive from the hard drive bay.
6.
If it is necessary to remove the hard drive bracket, remove the four Phillips PM3.0×3.0 hard drive
bracket screws (1) that secure the hard drive bracket to the hard drive.
7.
Lift the bracket (2) straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
46
Chapter 4 Removal and replacement procedures
ENWW
Computer feet
Description
Spare part number
Rubber Kit (includes base enclosure rubber feet and display bezel screw covers)
431430-001
The computer feet are adhesive-backed rubber pads. The feet attach to the base enclosure in the locations
illustrated below.
Memory module
Description
Spare part number
1024-MB, 667-MHz, PC2-5300, 1-DIMM
446495-001
512-MB, 667-MHz, PC2-5300, 1-DIMM
446494-001
Before removing the memory module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the memory module:
ENWW
1.
Position the computer with the front toward you.
2.
Loosen the two Phillips PM2.0×5.0 screws (1) that secure the memory/WLAN module compartment
cover to the computer.
Component replacement procedures
47
3.
Lift the left side of the cover (2), swing it to the right, and remove the cover.
NOTE: The memory/WLAN module compartment cover is included in the Plastics Kit, spare part
number 438368-001.
4.
Spread the retaining tabs (1) on each side of the memory module slot to release the memory module.
(The edge of the module opposite the slot rises away from the computer.)
5.
Remove the module (2) by pulling it away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect installation into the
memory module slot.
Reverse this procedure to install a memory module.
48
Chapter 4 Removal and replacement procedures
ENWW
RTC battery
NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords
and CMOS settings to be cleared.
Description
Spare part number
RTC battery (includes 2-sided tape)
446518-001
Before removing the RTC battery, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the memory/WLAN module compartment cover (see Memory module on page 47).
Remove the RTC battery:
1.
Disconnect the RTC battery cable (1) from the system board.
2.
Remove the RTC battery (2).
Reverse this procedure to install the RTC battery.
ENWW
Component replacement procedures
49
WLAN module
Description
Spare part number
802.11a/b/g/n WLAN modules:
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States,
Venezuela, and Vietnam
441086-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka,
Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
441087-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South Korea
441088-003
●
For use in Japan
441089-291
802.11a/b/g WLAN modules:
●
For use in Antigua & Barbuda, Argentina, Australia, the Bahamas, Barbados, Brunei, Canada,
Chile, the Dominican Republic, Guam, Guatemala, Hong Kong, India, Indonesia, Malaysia,
Mexico, New Zealand, Panama, Paraguay, Saudi Arabia, Taiwan, the United States, and
Vietnam
407674-001
●
For use in Aruba, Austria, Azerbaijan, Bahrain, Belgium, Bermuda, Brazil, Bulgaria, the Cayman
Islands, Colombia, Croatia, Cyprus, the Czech Republic, Denmark, Egypt, El Salvador, Estonia,
Finland, France, Georgia, Germany, Greece, Hungary, Iceland, Ireland, Italy, Jordan, Latvia,
Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the Netherlands, Norway,
Oman, the Philippines, Poland, Portugal, Romania, Russia, Serbia and Montenegro, Singapore,
Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, the United
Kingdom, and Uzbekistan
407674-002
●
For use in Ecuador, Haiti, Honduras, Pakistan, the People's Republic of China, Peru, Qatar, South
Korea, Uruguay, and Venezuela
407674-003
●
For use in Japan
407674-291
802.11b/g WLAN module for use in Thailand
407674-004
Before removing the WLAN module, follow these steps:
50
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the memory/WLAN module compartment cover (see Memory module on page 47).
Chapter 4 Removal and replacement procedures
ENWW
Remove the WLAN module:
1.
Disconnect the two WLAN antenna cables (1) from the WLAN module.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
NOTE: Computer models equipped with an 802.11a/b/g/n WLAN module will have an
additional wireless antenna cable (2), yellow in color.
2.
Remove the two Phillips PM2.0×3.0 screws (3) that secure the WLAN module to the computer. (The
edge of the module opposite the slot rises away from the computer.)
3.
Remove the WLAN module (4) by pulling it away from the slot at an angle.
NOTE: WLAN modules are designed with a notch (5) to prevent incorrect installation into the
WLAN module slot.
Reverse this procedure to install a WLAN module.
ENWW
Component replacement procedures
51
Optical drive
NOTE: All optical drive spare part kits include an optical drive bezel.
Description
Spare part number
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
446501-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
446500-001
DVD/CD-RW Combo Drive
446499-001
Before removing the optical drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the optical drive:
52
1.
Position the computer with right side toward you.
2.
Remove the Phillips PM2.5×7.0 screw (1) that secures the optical drive to the computer.
3.
Insert a thin tool, such as a paper clip (2), into the release access. (The optical drive disc tray is
partially ejected from the optical drive.)
4.
Use the disc tray frame to slide the optical drive (3) out of the computer.
5.
If it is necessary to replace the optical drive bracket, position the optical drive with the optical drive
bracket toward you.
6.
Remove the two Phillips PM2.0×3.0 screws (1) that secure the optical drive bracket to the optical
drive.
Chapter 4 Removal and replacement procedures
ENWW
7.
Remove the optical drive bracket (2).
Reverse the above procedure to reassemble and install the optical drive.
ENWW
Component replacement procedures
53
Switch cover
Description
Spare part number
Switch cover (includes LED board and cable)
446512-001
Before removing the switch cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
Remove the switch cover:
54
1.
Remove the three Phillips PM2.5×5.0 screws that secure the switch cover to the computer.
2.
Turn the computer display-side up, with the front toward you.
3.
Open the computer as far as possible.
Chapter 4 Removal and replacement procedures
ENWW
4.
Lift the rear edge of the switch cover and swing it forward until it rests on the keyboard.
5.
Release the zero insertion force (ZIF) connector (1) to which the power button board is connected,
and disconnect the cable from the power button board.
6.
Disconnect the microphone cable (2) from the power button board.
7.
Release the ZIF connector (3) to which the LED board is connected and disconnect the cable from
the power button board.
8.
Remove the switch cover.
Reverse this procedure to install the switch cover.
ENWW
Component replacement procedures
55
Speaker assembly
Description
Spare part number
Speaker assembly
431447-001
Before removing the speaker assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the switch cover (see Switch cover on page 54).
6.
Remove the keyboard (see Keyboard on page 58).
Remove the speaker assembly:
1.
Disconnect the speaker assembly cable (1) from the power button board.
2.
Remove the two Phillips PM2.5×2.0 screws (2) that secure the speaker assembly to the computer.
3.
Remove the speaker assembly (3).
Reverse this procedure to install the speaker assembly.
56
Chapter 4 Removal and replacement procedures
ENWW
Power button board
Description
Spare part number
Power button board (includes power button board cable)
431437-001
Before removing the power button board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the switch cover (see Switch cover on page 54).
6.
Remove the keyboard (see Keyboard on page 58).
Remove the power button board:
1.
Remove the Phillips PM2.0×3.0 screw (1) that secures the power button board to the fan/heat sink
assembly.
2.
Remove the power button board (2) from the switch cover.
3.
Remove the power button board.
Reverse this procedure to install the power button board.
ENWW
Component replacement procedures
57
Keyboard
For use in:
Spare part number
For use in:
Spare part number
Belgium
441427-A41
The Netherlands and Europe
441427-B31
The Czech Republic
441427-221
Portugal
441427-131
Denmark
441427-081
Russia
441427-251
Finland, Norway, and
Sweden
441427-DH1
Saudi Arabia
441427-171
441427-051
Spain
441427-071
441427-121
Switzerland
441427-111
441427-041
Taiwan
441427-AB1
441427-151
Thailand
441427-281
441427-BB1
Turkey
441427-141
441427-061
The United Kingdom
441427-031
441427-291
The United States
441427-001
France
French Canada
Germany
Greece
Israel
Italy
Japan
Korea
441427-AD1
Before removing the keyboard, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the switch cover (see Switch cover on page 54).
Remove the keyboard:
1.
58
Turn the computer upside down, with the front toward you.
Chapter 4 Removal and replacement procedures
ENWW
ENWW
2.
Remove the four Phillips PM2.5×7.0 screws that secure the keyboard to the computer.
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
Lift the rear edge of the keyboard (1) until it rests at an angle.
6.
Release the keyboard (2) by sliding it back to disengage the tabs on the front edge of the keyboard
from the top cover.
7.
Swing the keyboard (3) up and forward until it rests on the palm rest.
Component replacement procedures
59
8.
Release the ZIF connector (1) to which the keyboard cable is attached and disconnect the keyboard
cable (2) from the system board.
9.
Remove the keyboard.
Reverse this procedure to install the keyboard.
NOTE: The power button board cable and LED board cable are included in the Cable Kit, spare part
number 446519-001.
60
Chapter 4 Removal and replacement procedures
ENWW
Display assembly
Description
Spare part number
15.4-inch, WXGA, BrightView, display assembly for use only with computer models equipped with a
camera (includes camera and cable, microphones, and WLAN transceivers and antenna cables)
446481-001
15.4-inch, WXGA, BrightView, display assembly for use only with computer models not equipped
with a camera (includes microphones and WLAN transceivers and antenna cables)
446482-001
Before removing the display assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the memory/WLAN module compartment cover (see Memory module on page 47).
6.
Disconnect the wireless antenna cables from the WLAN module (see WLAN module on page 50).
7.
Remove the following components:
a.
Keyboard (see Keyboard on page 58)
b.
Switch cover (see Switch cover on page 54)
c.
Speaker assembly (see Speaker assembly on page 56)
Remove the display assembly:
ENWW
1.
Close the computer and turn it upside down, with the rear panel toward you.
2.
Remove the Phillips PM2.5×7.0 screws that secure the display assembly to the computer.
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer to an upright position.
Component replacement procedures
61
5.
Disconnect the following cables:
(1) Display panel cable
(2) Microphone cable
(3) Camera cable
6.
Remove the wireless antenna cables (4) from the routing channels (5) built into the top cover.
CAUTION: Support the display assembly when removing the following screws. Failure to support
the display assembly can result in damage to the display assembly and other computer components.
62
7.
Remove the two Phillips PM2.5×7.0 screws (1) that secure the display assembly to the computer.
8.
Remove the display assembly (2).
Chapter 4 Removal and replacement procedures
ENWW
9.
If it is necessary to replace the display bezel or any of the display assembly internal components,
remove the following:
(1) Four rubber screw covers on the display bezel top edge
(2) Two rubber screw covers on the display bezel bottom edge
(3) Six Phillips PM2.5×5.0 screws
NOTE: The display rubber screw covers are included in the Display Screw Kit, spare part number
431399-001.
10. Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the display
bezel until the bezel disengages from the display enclosure.
11. Remove the display bezel (3). Display bezels are available using the following spare part
numbers:
ENWW
●
446483-001 (for use only with computer models equipped with a camera; includes openings
for camera and microphones)
●
446484-001 (for use only with computer models not equipped with a camera; includes
openings for microphones)
Component replacement procedures
63
NOTE: See Camera module on page 41 for camera module replacement instructions. See Display
inverter on page 43 for display inverter replacement instructions.
12. If it is necessary to replace the display panel, remove the six Phillips PM2.5×4.0 screws (1) that
secure the display panel to the display enclosure.
13. Remove the display panel (2).
NOTE: The display panel is available using the spare part number 446480-001.
14. If it is necessary to replace the display hinges, remove the left and right hinge covers (1) by sliding
them off the display hinges. The display hinge covers are available using spare part number
431396-001.
15. Remove the two Phillips PM2.0×3.0 screws that secure each display hinge (2) to the display
panel.
16. Remove the display hinges (3). The display hinges are available using spare part number
431395-001.
17. If it is necessary to replace the wireless antenna transceivers and cables, remove the Phillips
PM2.0×3.0 screw (1) that secures each transceiver to the display enclosure.
18. Remove the wireless antenna cables from the clips (2) built into the display enclosure.
64
Chapter 4 Removal and replacement procedures
ENWW
19. Detach the wireless antenna transceivers (3) from the display enclosure and remove the transceivers
and cables (4). The wireless antenna transceivers and cables are available using the following spare
part numbers:
●
449727-001 (for use only with computer models equipped with an 802.11a/b/g/n WLAN
module; includes 3 transceivers and cables)
●
431398-001 (for use only with computer models equipped with an 802.11a/b/g or 802.11b/
g WLAN module; includes 2 transceivers and cables)
20. If it is necessary to replace the microphones and cables, release the retention tabs (1) built into the
display enclosure that secure the microphone cables to the display enclosure
21. Remove the microphone receivers (2) from the clips in the display enclosure.
22. Remove the microphone cables (3) from the display enclosure. The microphones and cables are
available using spare part number 431393-001.
23. If it is necessary to replace the camera cable, release the retention tabs (1) built into the display
enclosure that secure the camera cable to the display enclosure.
ENWW
Component replacement procedures
65
24. Remove the camera cable (2) from the display enclosure.
NOTE: The camera cable is included in the Display Cable Kit, spare part number 446489-001.
Reverse this procedure to reassemble and install the display assembly.
Top cover
Description
Spare part number
For use only with computer models equipped with a fingerprint reader (includes TouchPad and cable
and fingerprint reader board and cable)
446509-001
For use only with computer models not equipped with a fingerprint reader (includes TouchPad and
cable)
446508-001
Fingerprint reader board (includes fingerprint reader board cable)
446511-001
Before removing the top cover, follow these steps:
66
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Disconnect the power button board cable and the LED board cables from the system board (see
Keyboard on page 58).
6.
Remove the following components:
a.
Hard drive (see Hard drive on page 45)
b.
Optical drive (see Optical drive on page 52)
c.
Switch cover (see Switch cover on page 54)
Chapter 4 Removal and replacement procedures
ENWW
d.
Keyboard (see Keyboard on page 58)
e.
Speaker assembly (see Speaker assembly on page 56)
f.
Display assembly (see Display assembly on page 61)
Remove the top cover:
ENWW
1.
Remove the power button board cable and LED button board cable from the clips (1) built into the
top cover.
2.
Disconnect the power button board cable (2) and the LED button board cable (3) from the low
insertion force (LIF) connectors on the system board.
3.
Remove the power button board cable and LED board cable.
4.
Turn the computer upside down, with the front toward you.
5.
Remove the nine Phillips PM2.5×7.0 screws that secure the top cover to the computer.
Component replacement procedures
67
6.
Remove the following:
(1) Three Phillips PM2.5×2.0 screws in the optical drive bay
(2) One Phillips PM2.5×5.0 screw on the rear edge of the base enclosure
(3) Three Phillips PM2.5×7.0 screws on the rear edge of the base enclosure that secure the top cover
trim to the computer
(4) Two HM5.0×9.0 standoffs in the memory/WLAN module compartment
7.
Turn the computer right-side up, with the front toward you.
8.
Release and disconnect the TouchPad cable (1) from the ZIF connector on the system board.
9.
Remove the following screws:
(2) Two Phillips PM2.5×7.0 screws
(3) Two Phillips PM2.5×4.0 screws
(4) One Phillips PM2.5×5.0 screw that secures the top cover trim to the computer
68
Chapter 4 Removal and replacement procedures
ENWW
10. Remove the top cover trim (1).
NOTE: The top cover trim is available using spare part number 431421-001.
11. Lift the rear edge of the top cover (2) until it disengages from the computer.
12. Remove the top cover.
Reverse this procedure to install the top cover and top cover trim.
ENWW
Component replacement procedures
69
Bluetooth module
Description
Spare part number
Bluetooth module (includes Bluetooth module cable)
412766-002
Before removing the Bluetooth module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 45)
b.
Optical drive (see Optical drive on page 52)
c.
Switch cover (see Switch cover on page 54)
d.
Keyboard (see Keyboard on page 58)
e.
Speaker assembly (see Speaker assembly on page 56)
f.
Display assembly (see Display assembly on page 61)
g.
Top cover (see Top cover on page 66)
Remove the Bluetooth module:
70
1.
Disconnect the Bluetooth module cable (1) from the system board.
2.
Remove the two Phillips PM2.0×2.0 screws (2) that secure the Bluetooth module to the system board.
Chapter 4 Removal and replacement procedures
ENWW
3.
Remove the Bluetooth module (3).
Reverse this procedure to install the Bluetooth module.
ExpressCard assembly
Description
Spare part number
ExpressCard assembly
431439-001
Before removing the ExpressCard assembly, follow these steps:
ENWW
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 45)
b.
Optical drive (see Optical drive on page 52)
c.
Switch cover (see Switch cover on page 54)
d.
Keyboard (see Keyboard on page 58)
e.
Speaker assembly (see Speaker assembly on page 56)
f.
Display assembly (see Display assembly on page 61)
g.
Top cover (see Top cover on page 66)
Component replacement procedures
71
Remove the ExpressCard assembly:
1.
Press the ExpressCard slot bezel (1) to release the bezel from the ExpressCard slot.
2.
Remove the ExpressCard slot bezel (2).
NOTE: The ExpressCard slot bezel is included in the Plastics Kit, spare part number 438368-001.
3.
Remove the four Phillips PM2.5×4.0 screws (1) that secure the ExpressCard assembly to the system
board.
4.
Disconnect the ExpressCard assembly (2) from the system board by sliding to the right.
5.
Remove the ExpressCard assembly (3).
Reverse this procedure to install the ExpressCard assembly.
72
Chapter 4 Removal and replacement procedures
ENWW
USB/power connector board
Description
Spare part number
USB/power connector board (includes USB/power connector board cable)
449454-001
Before removing the USB/power connector board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 45)
b.
Optical drive (see Optical drive on page 52)
c.
Switch cover (see Switch cover on page 54)
d.
Keyboard (see Keyboard on page 58)
e.
Speaker assembly (see Speaker assembly on page 56)
f.
Display assembly (see Display assembly on page 61)
g.
Top cover (see Top cover on page 66)
Remove the USB/power connector board:
ENWW
1.
Remove the two Phillips PM2.5×4.0 screws (1) that secure the USB/power connector board to the
computer.
2.
Release the USB/power connector board (2) as far as the USB/power connector board cable will
allow.
Component replacement procedures
73
3.
Disconnect the USB cable (3) and the power connector cable (4) from the USB/power connector
board.
4.
Remove the USB/power connector board.
Reverse this procedure to install the USB/power connector board.
System board
Description
Spare part number
System board (includes modem cable)
446477-001
Before removing the system board, follow these steps:
74
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 45)
b.
Optical drive (see Optical drive on page 52)
c.
Switch cover (see Switch cover on page 54)
d.
Keyboard (see Keyboard on page 58)
e.
Speaker assembly (see Speaker assembly on page 56)
f.
Display assembly (see Display assembly on page 61)
Chapter 4 Removal and replacement procedures
ENWW
g.
Top cover (see Top cover on page 66)
h.
Audio board (see Audio board on page 77)
i.
USB/power connector board (see USB/power connector board on page 73)
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
Memory modules (see Memory module on page 47)
●
RTC battery (see RTC battery on page 49)
●
WLAN module (see WLAN module on page 50)
●
Bluetooth module (see Bluetooth module on page 70)
●
ExpressCard assembly (see ExpressCard assembly on page 71)
●
Fan/heat sink assembly (see Fan/heat sink assembly on page 78)
●
Processor (see Processor on page 80)
Remove the system board:
ENWW
1.
Remove the USB/power connector board cable (1) from the clips built into in the base enclosure.
2.
Remove the two Phillips PM2.5×4.0 screws (2) that secure the system board to the base enclosure.
3.
Use the optical drive connector (1) to lift the right side of the system board (2) until it rests at an
angle.
4.
Disconnect the audio board cable (3) from the system board.
Component replacement procedures
75
5.
Release the system board (4) by sliding it to the right until the connectors on the left side of the system
board disengage from the base enclosure.
6.
Remove the system board.
7.
If it is necessary to replace the USB/power connector board cable, turn the system board upside
down with the expansion port 3 toward you.
8.
Disconnect the power connector cable (1) and the USB board cable (2) from the system board.
NOTE: The USB/power connector board cable is included in the Cable Kit, spare part number
446519-001.
Reverse the above procedure to install the system board and USB/power connector board cable.
76
Chapter 4 Removal and replacement procedures
ENWW
Audio board
Description
Spare part number
Audio board (includes audio board cable)
446523-001
Before removing the audio board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 45)
b.
Optical drive (see Optical drive on page 52)
c.
Switch cover (see Switch cover on page 54)
d.
Keyboard (see Keyboard on page 58)
e.
Speaker assembly (see Speaker assembly on page 56)
f.
Display assembly (see Display assembly on page 61)
g.
Top cover (see Top cover on page 66)
h.
System board (see System board on page 74)
Remove the audio board:
ENWW
1.
Remove the two Phillips PM2.5×4.0 screws (1) that secure the audio board to the computer.
2.
Release the audio board (2) by sliding it back to disengage the audio connectors from the openings
in the base enclosure.
Component replacement procedures
77
3.
Remove the audio board (3) by lifting it straight up.
Reverse this procedure to install the audio board.
Fan/heat sink assembly
Description
Spare part number
Fan/heat sink assembly (includes thermal material)
446521-001
NOTE: When replacing the fan/heat sink assembly, be sure that the power button board is removed
from the defective fan/heat sink assembly and installed on the replacement fan/heat sink assembly.
See Power button board on page 57 for power button board removal information.
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the right side
and rear panel of the computer. The computer uses an electric fan for ventilation. The fan is controlled by
a temperature sensor and is designed to turn on automatically when high temperature conditions exist.
These conditions are affected by high external temperatures, system power consumption, power
management/battery conservation configurations, battery fast charging, and software applications.
Exhaust air is displaced through the ventilation grill located on the left side of the computer.
Before removing the fan/heat sink assembly, follow these steps:
78
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 45)
b.
Optical drive (see Optical drive on page 52)
Chapter 4 Removal and replacement procedures
ENWW
c.
Switch cover (see Switch cover on page 54)
d.
Keyboard (see Keyboard on page 58)
e.
Speaker assembly (see Speaker assembly on page 56)
f.
Display assembly (see Display assembly on page 61)
g.
Top cover (see Top cover on page 66)
h.
Audio board (see Audio board on page 77)
i.
USB/power connector board (see USB/power connector board on page 73)
j.
System board (see System board on page 74)
Remove the fan/heat sink assembly:
1.
Turn the system board upside down with the expansion port 3 and external monitor port toward you.
2.
Disconnect the fan cable (1) from the system board.
3.
Loosen the three Phillips PM2.5×5.0 screws (2) and the Phillips PM2.5×4.0 screw (3) that secure
the fan/heat sink assembly to the system board.
4.
Remove the fan/heat sink assembly (4).
NOTE: Due to the adhesive quality of the thermal paste and thermal pads located between the
fan/heat sink assembly and system board components, it may be necessary to move the fan/heat
sink assembly from side to side to detach the assembly.
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink
assembly (1) and (2), the processor (3), and the system board component (4) each time the fan/heat
sink assembly is removed. Thermal material must be installed on all surfaces before the fan/heat sink
assembly is reinstalled. Thermal material is included with all fan/heat sink assembly, system board, and
processor spare part kits.
ENWW
Component replacement procedures
79
Reverse this procedure to install the fan/heat sink assembly.
Processor
NOTE: All processor spare part kits include thermal paste.
Description
Spare part number
Intel Core Duo T7300 2.0-GHz processor (4 MB of L2 cache)
446478-001
Intel Core Duo T7100 1.8-GHz processor (2 MB of L2 cache)
446479-001
Before removing the processor, follow these steps:
80
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 40).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 45)
b.
Optical drive (see Optical drive on page 52)
c.
Switch cover (see Switch cover on page 54)
d.
Keyboard (see Keyboard on page 58)
e.
Speaker assembly (see Speaker assembly on page 56)
f.
Display assembly (see Display assembly on page 61)
g.
Top cover (see Top cover on page 66)
Chapter 4 Removal and replacement procedures
ENWW
h.
Audio board (see Audio board on page 77)
i.
USB/power connector board (see USB/power connector board on page 73)
j.
System board (see System board on page 74)
k.
Fan/heat sink assembly (see Fan/heat sink assembly on page 78)
Remove the processor:
1.
Turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.
2.
Lift the processor (2) straight up and remove it.
NOTE: The gold triangle (3) on the processor must be aligned with the triangle icon (4) embossed
on the processor socket when you install the processor.
Reverse this procedure to install the processor.
ENWW
Component replacement procedures
81
82
Chapter 4 Removal and replacement procedures
ENWW
5
Setup Utility
Starting the Setup Utility
The Setup Utility is a ROM-based information and customization utility that can be used even when your
Windows® operating system is not working or will not load.
NOTE:
The fingerprint reader (select models only) does not work when accessing the Setup Utility.
The utility reports information about the computer and provides settings for startup, security, and other
preferences.
To start the Setup Utility:
1.
Turn on or restart the computer.
2.
Before Windows opens and while “Press <F10> to enter setup” is displayed in the lower-left corner
of the screen, press f10.
Changing the language of the Setup Utility
The following procedure explains how to change the language of the Setup Utility. If the Setup Utility is
not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press <F10> to
enter setup” is displayed in the lower-left corner of the screen.
2.
Use the arrow keys to select System Configuration > Language, and then press enter.
3.
Press f5 or f6 (or use the arrow keys) to select a language, and then press enter to select a language.
4.
When a confirmation prompt with your preference selected is displayed, press enter to save your
preference.
5.
To set your preferences and exit the Setup Utility, press f10 and then follow the instructions on the
screen.
Your preferences go into effect when the computer restarts in Windows.
ENWW
Starting the Setup Utility
83
Navigating and selecting in the Setup Utility
Because the Setup Utility is not Windows-based, it does not support the TouchPad. Navigation and
selection are by keystroke.
●
To choose a menu or a menu item, use the arrow keys.
●
To choose an item in a drop-down list or to toggle a field, for example an Enable/Disable field, use
either the arrow keys or f5 or f6.
●
To select an item, press enter.
●
To close a text box or return to the menu display, press esc.
●
To display additional navigation and selection information while the Setup Utility is open, press f1.
Displaying system information
The following procedure explains how to display system information in the Setup Utility. If the Setup Utility
is not open, begin at step 1. If the Setup Utility is open, begin at step 2.
1.
To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press <F10>to
enter setup” is displayed in the lower-left corner of the screen.
2.
Access the system information by using the Main menu.
3.
To exit the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter. (The computer restarts in Windows.)
Restoring default settings in the Setup Utility
The following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is not
already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
To start the Setup Utility, turn on or restart the computer, and then press f10 while “Press <F10>to
enter setup” is displayed in the lower-left corner of the screen.
2.
Select Exit > Load Setup Defaults, and then press enter.
3.
When the Setup Confirmation is displayed, press enter to save your preferences.
4.
To set your preferences and exit the Setup Utility, press f10, and then follow the instructions on the
screen.
The Setup Utility default settings are set when you exit the Setup Utility and go into effect when the computer
restarts.
NOTE: Your password, security, and language settings are not changed when you restore the factory
default settings.
84
Chapter 5 Setup Utility
ENWW
Using advanced Setup Utility features
This chapter describes the Setup Utility features recommended for all users. For more information about
the Setup Utility features recommended for advanced users only, refer to Help and Support, which is
accessible only when the computer is in Windows.
The Setup Utility features available for advanced users include a hard drive self-test, a Network Service
Boot, and settings for boot order preferences.
The “<F12> to boot from LAN” message that is displayed in the lower-left corner of the screen each time
the computer is started or restarted in Windows is the prompt for a Network Service Boot.
The “Press <ESC> to change boot order” message that is displayed in the lower-left corner of the screen
each time the computer is started or restarted in Windows is the prompt to change the boot order.
Closing the Setup Utility
You can close the Setup Utility with or without saving changes.
●
To close the Setup Utility and save your changes from the current session, use either of the following
procedures:
◦
Press f10, and then follow the instructions on the screen.
—or—
◦
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Saving Changes, and then press enter.
When you use the f10 procedure, you are offered an option to return to the Setup Utility. When
you use the Exit Saving Changes procedure, the Setup Utility closes when you press enter.
●
To close the Setup Utility without saving your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow
keys to select Exit > Exit Discarding Changes, and then press enter.
After the Setup Utility closes, the computer restarts in Windows.
Setup Utility menus
The menu tables in this section provide an overview of Setup Utility options.
NOTE:
Some of the Setup Utility menu items listed in this section may not be supported by your computer.
Main menu
ENWW
Select
To do this
System information
●
View and change the system time and date.
●
View identification information about the computer.
●
View specification information about the processor, memory
size, system BIOS, and keyboard controller version (select
models only).
Using advanced Setup Utility features
85
Security menu
Select
To do this
Administrator password
Enter, change, or delete an administrator password.
Power-On Password
Enter, change, or delete a power-on password.
System Configuration menu
Select
To do this
Language Support
Change the Setup Utility language.
Enhanced SATA support (select models only)
Enable/disable enhanced SATA mode.
Boot Options
Set the following boot options:
●
f10 and f12 Delay (sec.)―Set the delay for the f10 and f12
functions of the Setup Utility in intervals of 5 seconds each (0, 5,
10, 15, 20).
●
CD-ROM boot―Enable/disable boot from CD-ROM.
●
Floppy boot―Enable/disable boot from Floppy.
●
Internal Network Adapter boot―Enable/disable boot from
Internal Network Adapter.
●
Boot Order―Set the boot order for:
◦
USB Floppy
◦
ATAPI CD/DVD ROM Drive
◦
Hard drive
◦
USB Diskette on Key
◦
USB Hard drive
◦
Network adapter
Button Sound (select models only)
Enable/disable the Quick Launch Button tapping sound.
Video memory up to (select models only)
Select the amount of video memory.
Diagnostics menu
Select
To do this
Hard Disk Self Test
Run a comprehensive self-test on the hard drive.
NOTE: On models equipped with two hard drives, this menu option
is called the Primary Hard Disk Self Test.
Secondary Hard Disk Self Test (select models only)
86
Chapter 5 Setup Utility
Run a comprehensive self-test on a secondary hard drive.
ENWW
6
Specifications
Computer specifications
Metric
U.S.
Height (front to back)
4.09 cm
1.61 in
Width
35.71 cm
14.06 in
Depth
25.71 cm
10.12 in
Weight (with optical drive, hard drive, and battery)
2.86 kg
6.31 lbs
Dimensions
Input power
Operating voltage
18.5 V dc —19.0 V dc
Operating current
3.5 A or 4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating (14.7 to 10.1 psia)
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating (14.7 to 4.4 psia)
-15 m to 12,192 m
-50 ft to 40,000 ft
Shock
Operating
125 g, 2 ms, half-sine
Nonoperating
200 g, 2 ms, half-sine
Random vibration
Operating
ENWW
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
Computer specifications
87
Metric
Nonoperating
U.S.
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
15.4-inch, WXGA, BrightView display specifications
Metric
U.S.
Height
20.7 cm
8.15 in
Width
33.1 cm
13.03 in
Diagonal
39.1 cm
15.39 in
Number of colors
Up to 16.8 million
Contrast ratio
200:1 (typical)
Brightness
150 nits (typical)
Dimensions
Pixel resolution
88
Pitch
0.259 × 0.259 mm
Format
1280 × 800
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4W
Viewing angle
+/-65° horizontal, +/-50° vertical (typical)
Chapter 6 Specifications
ENWW
Hard drive specifications
200-GB*
160-GB*
120-GB*
80-GB*
60-GB*
Height
9.5 mm
9.5 mm
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
70 mm
70 mm
Weight
102 g
102 g
102 g
102 g
102 g
Interface type
SATA
SATA
SATA
SATA
SATA
Synchronous (maximum)
100 MB/sec
100 MB/sec
100 MB/sec
100 MB/sec
100 MB/sec
Security
ATA security
ATA security
ATA security
ATA security
ATA security
Dimensions
Transfer rate
Seek times (typical read, including setting)
Single track
3 ms
3 ms
3 ms
3 ms
3 ms
Average
13 ms
13 ms
13 ms
13 ms
13 ms
Maximum
24 ms
24 ms
24 ms
24 ms
24 ms
Logical blocks
390,706,000
312,560,480
234,433,260
156,280,320
117,210,180
Disk rotational speed
4200 rpm
5400 rpm
5400 rpm
5400 rpm
5400 rpm
Operating temperature
NOTE:
5°C to 55°C (41°F to 131°F)
Certain restrictions and exclusions apply. Consult technical support for details.
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Accessible capacity is less. Actual drive specifications
may differ slightly.
ENWW
Hard drive specifications
89
DVD±RW and CD-RW Super Multi Double-Layer
Combo Drive specifications
Applicable disc
Center hole diameter
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT,
CD-ROM, CD-ROM XA, MIXED MODE
CD, CD-I, CD-I Bridge (Photo-CD, Video
CD), Multisession CD (Photo-CD, CDEXTRA, Portfolio, CD-R, CD-RW), CD-R,
CD-RW, DVD-ROM (DVD-5, DVD-9,
DVD-10, DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
DVD+R, DVD+RW, DVD-R, DVD-RW,
DVD-RAM
1.5 cm (0.59 in)
Disc diameter
Standard disc
12 cm (4.72 in)
Mini disc
8 cm (3.15 in)
Disc thickness
1.2 mm (0.047 in)
Track pitch
0.74 µm
Access time
CD
DVD
Random
< 175 ms
< 230 ms
Full stroke
< 285 ms
< 335 ms
Audio output level
Audio-out, 0.7 Vrms
Cache buffer
2 MB
Data transfer rate
90
24X CD-ROM
3,600 KB/sec
8X DVD
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
Transfer mode
Multiword DMA Mode
Startup time
< 15 seconds
Stop time
< 6 seconds
Chapter 6 Specifications
ENWW
System DMA specifications
Hardware DMA
System function
DMA0
Not applicable
DMA1*
Not applicable
DMA2*
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5*
Available for PC Card
DMA6
Not assigned
DMA7
Not assigned
*PC Card controller can use DMA 1, 2, or 5.
ENWW
System DMA specifications
91
System interrupt specifications
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ2
Cascaded
IRQ3
Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
IRQ4
COM1
IRQ5*
Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
Parallel port
IRQ8
System CMOS/real-time clock
IRQ9*
Microsoft ACPI-compliant system
IRQ10*
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
IRQ11
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
IRQ12
Synaptics PS/2 TouchPad
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
*Default configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: PC Cards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial port
may assert IRQ3 or IRQ4.
92
Chapter 6 Specifications
ENWW
System I/O address specifications
ENWW
I/O address (hex)
System function (shipping configuration)
000 - 00F
DMA controller no. 1
010 - 01F
Unused
020 - 021
Interrupt controller no. 1
022 - 024
Opti chipset configuration registers
025 - 03F
Unused
02E - 02F
87334 “Super I/O” configuration for CPU
040 - 05F
Counter/timer registers
044 - 05F
Unused
060
Keyboard controller
061
Port B
062 - 063
Unused
064
Keyboard controller
065 - 06F
Unused
070 - 071
NMI enable/RTC
072 - 07F
Unused
080 - 08F
DMA page registers
090 - 091
Unused
092
Port A
093 - 09F
Unused
0A0 - 0A1
Interrupt controller no. 2
I/O Address (hex)
System Function (shipping configuration)
0A2 - 0BF
Unused
0C0 - 0DF
DMA controller no. 2
0E0 - 0EF
Unused
0F0 - 0F1
Coprocessor busy clear/reset
0F2 - 0FF
Unused
100 - 16F
Unused
170 - 177
Secondary fixed disk controller
178 - 1EF
Unused
1F0 - 1F7
Primary fixed disk controller
1F8 - 200
Unused
201
JoyStick (decoded in ESS1688)
202 - 21F
Unused
System I/O address specifications
93
94
I/O address (hex)
System function (shipping configuration)
220 - 22F
Entertainment audio
230 - 26D
Unused
26E - 26
Unused
278 - 27F
Unused
280 - 2AB
Unused
2A0 - 2A7
Unused
2A8 - 2E7
Unused
2E8 - 2EF
Reserved serial port
2F0 - 2F7
Unused
2F8 - 2FF
Infrared port
300 - 31F
Unused
320 - 36F
Unused
370 - 377
Secondary diskette drive controller
378 - 37F
Parallel port (LPT1/default)
380 - 387
Unused
388 - 38B
FM synthesizer—OPL3
38C - 3AF
Unused
3B0 - 3BB
VGA
3BC - 3BF
Reserved (parallel port/no EPP support)
3C0 - 3DF
VGA
3E0 - 3E1
PC Card controller in CPU
3E2 - 3E3
Unused
3E8 - 3EF
Internal modem
3F0 - 3F7
“A” diskette controller
3F8 - 3FF
Serial port (COM1/default)
CF8 - CFB
PCI configuration index register (PCIDIVO-1)
CFC - CFF
PCI configuration data register (PCIDIVO-1)
Chapter 6 Specifications
ENWW
System memory map specifications
ENWW
Size
Memory address
System function
640 KB
00000000-0009FFFF
Base memory
128 KB
000A0000-000BFFFF
Video memory
48 KB
000C0000-000CBFFF
Video BIOS
160 KB
000C8000-000E7FFF
Unused
64 KB
000E8000-000FFFFF
System BIOS
15 MB
00100000-00FFFFFF
Extended memory
58 MB
04800000-07FFFFFF
Super extended memory
58 MB
04800000-07FFFFFF
Unused
2 MB
08000000-080FFFFF
Video memory (direct access)
4 GB
08200000-FFFEFFFF
Unused
64 KB
FFFF0000-FFFFFFFF
System BIOS
System memory map specifications
95
96
Chapter 6 Specifications
ENWW
7
Screw listing
This section provides specification and reference information for the screws and standoffs used in the
computer. All screws and standoffs listed in this section are available in the Screw Kit, spare part number
434747-001, and the Display Screw Kit, spare part number 431399-001.
ENWW
97
Phillips PM2.0×5.0 captive screw
Color
Quantity
Length
Thread
Head width
Black
4
5.0 mm
2.0 mm
5.0 mm
Where used:
(1) Two screws (secured by C-clips) that secure the hard drive cover to the computer
(2) Two screws (secured by C-clips) that secure the memory/WLAN module compartment cover to the
computer
98
Chapter 7 Screw listing
ENWW
Phillips PM3.0×4.0 screw
Color
Quantity
Length
Thread
Head width
Silver
4
4.0 mm
3.0 mm
5.0 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
ENWW
Phillips PM3.0×4.0 screw
99
Phillips PM2.0×3.0 screw
Color
Quantity
Length
Thread
Head width
Silver
11
3.0 mm
2.0 mm
4.5 mm
Where used: 2 screws that secure the WLAN module to the system board
Where used: 2 screws that secure the optical drive bracket to the optical drive
100 Chapter 7 Screw listing
ENWW
Where used: One screw that secures the power button board to the fan/heat sink assembly
Where used: 4 screws that secure the display hinges to the display panel
Where used: 2 screws that secure the wireless antenna transceivers to the display enclosure
ENWW
Phillips PM2.0×3.0 screw 101
Phillips PM2.5×7.0 screw
Color
Quantity
Length
Thread
Head width
Black
23
7.0 mm
2.5 mm
5.0 mm
Where used:
(1) One screw that secures the optical drive to the computer
(2) Four screws that secure the keyboard to the computer
(3) Two screws that secure the display assembly to the computer
102 Chapter 7 Screw listing
ENWW
Where used: 2 screws that secure the display assembly to the computer
Where used: 9 screws that secure the top cover to the computer
Where used: 3 screws that secure the top cover trim to the computer
ENWW
Phillips PM2.5×7.0 screw 103
Where used: 2 screws that secure the top cover to the computer
104 Chapter 7 Screw listing
ENWW
Phillips PM2.5×5.0 screw
Color
Quantity
Length
Thread
Head width
Black
11
5.0 mm
2.5 mm
5.0 mm
Where used: 3 screws that secure the switch cover to the computer
ENWW
Phillips PM2.5×5.0 screw 105
Where used: 6 screws that secure the display bezel to the display assembly
Where used: One screw that secures the top cover to the computer
Where used: One screw that secures the top cover to the computer
106 Chapter 7 Screw listing
ENWW
Phillips PM2.5×2.0 screw
Color
Quantity
Length
Thread
Head width
Silver
5
2.0 mm
2.5 mm
7.0 mm
Where used: 2 screws that secure the speaker assembly to the computer
Where used: 3 screws that secure the top cover to the computer
ENWW
Phillips PM2.5×2.0 screw 107
Phillips PM2.5×4.0 screw
Color
Quantity
Length
Thread
Head width
Silver
18
4.0 mm
2.5 mm
5.0 mm
Where used: 6 screws that secure the display panel to the display assembly
Where used: 2 screws that secure the top cover to the computer
108 Chapter 7 Screw listing
ENWW
Where used:
(1) Four screws that secure the ExpressCard assembly to the computer
(2) Two screws that secure the USB/power connector board to the computer
(3) Two screws that secure the system board to the computer
Where used: 2 screws that secure the audio board to the computer
ENWW
Phillips PM2.5×4.0 screw 109
Hex HM5.0×9.0 standoff
Color
Quantity
Length
Thread
Head width
Silver
2
9.0 mm
2.5 mm
5.0 mm
Where used: 2 standoffs that secure the top cover to the computer
110 Chapter 7 Screw listing
ENWW
Phillips PM2.0×2.0 screw
Color
Quantity
Length
Thread
Head width
Silver
2
2.0 mm
2.0 mm
4.0 mm
Where used: 2 screws that secure the Bluetooth module to the system board
ENWW
Phillips PM2.0×2.0 screw 111
Phillips PM2.5×5.0 captive screw
Color
Quantity
Length
Thread
Head width
Black
3
5.0 mm
2.5 mm
5.0 mm
Where used: 3 screws that secure the fan/heat sink to the computer
112 Chapter 7 Screw listing
ENWW
Phillips 2.5×4.0 captive screw
Color
Quantity
Length
Thread
Head width
Silver
1
4.0 mm
2.5 mm
5.0 mm
Where used: One captive screw (secured by a C-clip) that secures the fan/heat sink assembly to the
system board
ENWW
Phillips 2.5×4.0 captive screw 113
114 Chapter 7 Screw listing
ENWW
8
Backup and Recovery
Recovering system information
Tools provided by the operating system and Recovery Manager software are designed to help you with
the following tasks for safeguarding your information and restoring it in case of a system failure:
●
Back up your information regularly to protect your important system files.
●
Make a set of recovery discs (Recovery Manager software feature). Recovery discs are used to start
up (boot) your computer and restore the operating system and software programs to factory settings
in case of system failure or instability.
●
Create system restore points (operating system feature). System restore points allow you to reverse
undesirable changes to your computer by restoring the computer to an earlier state.
●
Recover a program or driver (Recovery Manager software feature). This feature helps you reinstall
a program or driver without performing a full system recovery.
●
Perform a full system recovery (Recovery Manager software feature). With Recovery Manager, you
can recover your full factory image if you experience system failure or instability. Recovery Manager
works from a dedicated recovery partition on the hard drive or from recovery discs you create.
Backing up your information
When to back up
●
On a regularly scheduled basis.
NOTE: Set reminders to back up your information periodically.
ENWW
●
Before the computer is repaired or restored.
●
Before you add or modify hardware or software.
Recovering system information 115
Back up suggestions
●
Create system restore points using the Windows System Restore feature.
●
Store personal files in the Documents folder and back up these folders periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a.
Display the screen.
b.
Copy the screen:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.
Open a word-processing document, and then select Edit > Paste.
Using system restore points
When you back up your system, you are creating a system restore point. A system restore point allows
you to save and name a snapshot of your hard drive at a specific point in time. You can then recover
back to that point if you want to reverse subsequent changes made to your system.
NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since
the last restore point.
You also can create additional restore points to provide increased protection for your system files and
settings.
When to create restore points
●
Before you add or extensively modify software or hardware.
●
Periodically, whenever the system is performing optimally.
NOTE: If you revert to a restore point and then change your mind, you can reverse the restoration.
Create a system restore point
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System protection.
3.
Click the System Protection tab.
4.
Under Automatic restore points, select the disk for which you want to create a restore point.
5.
Click Create.
The System Protection window opens.
6.
Follow the on-screen instructions.
116 Chapter 8 Backup and Recovery
ENWW
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning
optimally, follow these steps:
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System protection.
3.
Click the System Protection tab.
4.
Click the System Restore button, and then click Next.
The System Restore window opens.
5.
Follow the on-screen instructions.
Creating recovery discs
Recovery Manager creates a set of recovery CDs or DVDs for the computer. Use recovery discs to restore
the operating system and software programs to factory settings, in case of system failure or instability.
NOTE: Handle these discs carefully and keep them in a safe place. The software allows the creation of
only one set of recovery discs.
Note the following guidelines before creating recovery discs:
●
You will need high quality CD-R, DVD-R, or DVD+R discs (purchased separately).
NOTE: Formatted DVD±RW discs and DVD±RW double-layer discs are not compatible with the
Recovery Manager software.
●
The computer must be connected to AC power during this process.
●
Only one set of recovery discs can be created per computer.
●
Number each disc before inserting it into the computer optical drive.
●
If necessary, you can exit the program before you have finished creating the recovery discs. The next
time you open Recovery Manager, you will be prompted to continue the disc creation process.
To create a set of recovery discs:
1.
Select Start > All Programs > Recovery Manager > Recovery Manager.
Recovery Manager opens.
2.
Click Advanced Options.
NOTE: If you are operating the computer on battery power, you will be prompted to connect to
AC power before you can go to the next step.
ENWW
3.
Click Recovery disc creation, and then click Next.
4.
Follow the on-screen instructions.
Recovering system information 117
Reinstalling software programs and drivers
If a program or driver preinstalled at the factory is accidentally erased or is damaged, Recovery Manager
allows you to reinstall it.
NOTE: Software not provided with this computer must be reinstalled from the disc provided by the
manufacturer or downloaded from the manufacturer's Web site.
NOTE: Before reinstalling the program, be sure it is fully uninstalled.
Recovery Manager replaces corrupted system files and reinstalls deleted system files within the program.
●
In most cases, if the program you are reinstalling is still on your computer, the reinstallation process
does not affect your personal settings.
●
In all cases, if a program has been deleted from your computer, the reinstallation process reinstalls
the program or utility to the factory image but cannot restore your personal settings.
Reinstalling preinstalled programs and drivers
1.
Remove the program or driver:
NOTE: In some cases, drivers are not listed in the Programs and Features list. If the driver is not
listed, it does not need to be removed.
2.
a.
Select Start > Control Panel > Programs > Uninstall a program.
b.
Right-click the program or driver you want to remove, and then click Uninstall.
Reinstall the program or driver:
a.
Select Start > All Programs > Recovery Manager > Recovery Manager.
Recovery Manager opens.
b.
Click Advanced Options.
c.
Click either Software program re-installation or Hardware driver re-installation,
and then click Next.
d.
Follow the on-screen instructions.
e.
Restart the computer if prompted.
Reinstalling programs from discs
1.
Insert the disc into the optical drive.
2.
When the installation wizard opens, follow the installation instructions on the screen.
3.
Restart the computer if prompted.
118 Chapter 8 Backup and Recovery
ENWW
Performing a recovery
Recovery Manager software allows you to repair or restore the system if you experience system failure or
instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery
partition on the hard drive.
NOTE: Windows has its own built-in repair features, such as System Restore and driver rollback
capabilities. If you have not already tried these features, try them before using Recovery Manager.
NOTE: Recovery Manager only recovers software that was preinstalled at the factory. Software not
provided with this computer must be reinstalled from the disc provided by the manufacturer or downloaded
from the manufacturer's Web site.
Recovering from the recovery discs
To restore the system from the recovery discs:
1.
Back up all personal files.
2.
Insert the first recovery disc into the optical drive and restart the computer.
3.
Follow the on-screen instructions.
Recovering from the partition on the hard drive
You can perform a recovery from the partition on the hard drive from either the Start button or f11.
To restore the system from the partition, follow these steps:
1.
Access Recovery Manager in either of the following ways:
●
Select Start > All Programs > Recovery Manager > Recovery Manager.
●
Restart the computer and press f11 while the “Press <F11> for recovery” message is displayed
on the screen. Then select Recovery Manager.
Recovery Manager opens.
ENWW
2.
Click Advanced Options.
3.
Click System recovery, and then click Next.
4.
Follow the on-screen instructions.
Recovering system information 119
Deleting the recovery partition on the hard drive
The Recovery Manager Advanced Options menu provides the option of deleting the recovery partition,
which will increase space on the hard drive. Delete the recovery partition only if you have already created
recovery discs.
CAUTION: After you create the recovery discs, you can increase space on the hard drive by deleting
the recovery partition. However, doing this is not recommended. If you delete this partition, you will lose
any information that is on the partition, including Recovery Manager software. Thereafter, you must use
the recovery discs to access Recovery Manager software.
To delete the recovery partition:
1.
If you have not already created recovery discs, create them now.
2.
Select Start > All Programs > Recovery Manager > Recovery Manager.
Recovery Manager opens.
3.
Click Advanced Options.
4.
Click Remove recovery partition, and then click Next.
5.
Follow the on-screen instructions.
Updating reinstalled software
After you perform a system recovery, connect to the Internet to update all reinstalled software.
To access update links for the operating system and other software provided on your computer:
Select Start > Help and Support.
To update optional software, follow the instructions provided by the software manufacturer. Some
programs include an update feature you can access from a Help button or menu within the program.
120 Chapter 8 Backup and Recovery
ENWW
9
Connector pin assignments
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
Audio-out (headphone)
ENWW
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
Audio-in (microphone) 121
External monitor
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
122 Chapter 9 Connector pin assignments
ENWW
RJ-11 (modem)
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
RJ-45 (network)
ENWW
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
RJ-11 (modem) 123
S-Video-out
Pin
Signal
1
S-VHS color (C) signal
2
Composite video signal
3
S-VHS intensity (Y) signal
4
S-VHS color ground
5
TV-CD
6
S-VHS intensity ground
7
Composite video ground
Universal Serial Bus
Pin
Signal
1
+5 VDC
2
Data -
3
Data +
4
Ground
124 Chapter 9 Connector pin assignments
ENWW
10 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country
or region where the equipment is purchased.
Power cord sets for use in other countries or regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries or regions
The requirements listed below are applicable to all countries or regions:
ENWW
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for evaluation
in the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating
of 125 or 250 V AC, as required by each country or region’s power system.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for all countries or regions 125
Requirements for specific countries or regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
Korea
EK
4
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
CCC
5
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug
must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
5.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
126 Chapter 10 Power cord set requirements
ENWW
11 Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household
waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Caution must be exercised when removing and handling
the backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling must be exercised when removing these components.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of
environmental considerations. For disposal or recycling information, contact your local authorities, or see
the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific details,
such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from one
computer model to another.
ENWW
Battery 127
Perform the following steps to disassemble the display assembly:
1.
Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2.
Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3.
Remove the display bezel (3).
128 Chapter 11 Recycling
ENWW
ENWW
4.
Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5.
Remove all screws (1) that secure the display panel assembly to the display enclosure.
6.
Remove the display panel assembly (2) from the display enclosure.
7.
Turn the display panel assembly upside down.
8.
Remove all screws that secure the display panel frame to the display panel.
9.
Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
Display 129
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
130 Chapter 11 Recycling
ENWW
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
17. Remove the backlight frame from the display panel.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
ENWW
Display 131
18. Remove the backlight from the backlight frame.
19. Disconnect the display cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
132 Chapter 11 Recycling
ENWW
Index
Symbols/Numerics
1394 port, location 14
A
AC adapter, spare part
number 26, 27
administrator password 86
advanced Setup Utility
features 85
antenna
removal 64
spare part numbers 22, 28,
31, 65
applications key, Windows 9
audio board
removal 77
spare part number 20, 31,
77
audio board cable, illustrated 24
audio, product description 2
audio-in jack
location 11
pin assignments 121
audio-out jack
location 11
pin assignments 121
audio-out S/PDIF jack,
location 11
B
backpack, spare part
number 26, 28
backup 115
base enclosure, spare part
number 20, 31
battery
removal 40
spare part numbers 20, 28,
30, 40
battery bay 15
ENWW
battery light 6, 11
battery release latch 15
bezel
illustrated 22
spare part numbers 22, 63
Bluetooth module
removal 70
spare part number 20, 28,
70
Bluetooth module cable,
illustrated 24
boot options 86
boot order 86
bottom components 15
button sound 86
buttons
DVD 7
media 7
next/fast forward 8
play/pause 8
power 7
previous/rewind 7
stop 8
volume mute 8
C
Cable Kit
contents 24
spare part number 21, 24,
31
cables, service considerations 34
camera
location 5
product description 2
camera cable
removal 65
spare part number 66
camera light 5
camera module
illustrated 22
removal 41, 42
spare part number 22, 30,
41, 42
caps lock light 6
carrying case, spare part
number 26, 28
changing the Setup Utility
language 83
chipset, product description 1
closing the Setup Utility 85
CMOS clearing 38
components
bottom 15
display 5
front 11
keyboard 9
left-side 13
lights 6
rear 13
right-side 12
top 6
TouchPad 10
composite video cable, spare part
number 26, 28
computer feet
locations 47
spare part number 20, 47
computer specifications 87
connector pin assignments
audio-in 121
audio-out 121
external monitor 122
headphone 121
microphone 121
modem 123
monitor 122
network 123
RJ-11 123
RJ-45 123
Index 133
S-Video-out 124
Universal Serial Bus (USB) 124
connectors, service
considerations 34
D
Diagnostics menu 86
Digital Media Slot 14
Digital Media Slot light 14
diskette drive
precautions 34
product description 2
display assembly
removal 61
spare part numbers 18, 30,
61
display bezel
illustrated 22
release 41, 43
spare part numbers 22, 30,
63
Display Cable Kit, spare part
number 22, 30
display components
illustrated 22
recycling 127
spare part numbers 22
display enclosure
illustrated 22
spare part number 22, 30
display hinge
removal 64
spare part number 64
display hinge cover
removal 64
spare part number 64
Display Hinge Cover Kit, spare part
number 28
Display Hinge Kit, spare part
number 22, 28
display inverter
illustrated 22
removal 43, 44
spare part number 22, 28,
43
Display Label Kit, spare part
number 23, 31
display panel
illustrated 22
product description 1
134 Index
removal 64
spare part number 22, 30,
64
Display Screw Kit, spare part
number 23, 28
display specifications 88
display switch 5
docking support, product
description 3
drive light 6, 11
drivers, reinstalling 118
drives
preventing damage 34
drives, boot order 86
DVB-T antenna adapter, spare part
number 26, 28
DVB-T tuner, spare part
number 26, 28
DVD button 7
DVD/CD-RW Combo Drive
precautions 34
removal 52
spare part number 21, 25,
30, 52
specifications 90
DVD±RW and CD-RW Combo Drive
precautions 34
removal 52
spare part numbers 21, 25,
30, 52
specifications 90
E
electrostatic discharge 35
enhanced SATA support 86
esc key 9
Ethernet, product description 2
expansion port 3 13
ExpressCard assembly
removal 71
spare part number 20, 28,
71
ExpressCard Kit, spare part
number 26, 30
ExpressCard slot 12
ExpressCard slot bezel
illustrated 23
removal 72
external media cards, product
description 2
external monitor port
location 13
pin assignments 122
F
fan/heat sink assembly
removal 78
spare part number 20, 31,
78
feet
locations 47
spare part number 20, 47
fingerprint reader 8, 83
fingerprint reader board, spare part
number 20, 31, 66
fn key 9
front components 11
function keys 9
G
graphics, product description 1
grounding equipment and
methods 37
H
hard drive
precautions 34
product description 1
removal 45
spare part numbers 20, 25,
29, 30, 45
specifications 89
hard drive bay 15
hard drive cover
illustrated 23
removal 45
hard drive self test 86
HDMI port 13
headphone jack
location 11
pin assignments 121
headset, spare part number 26,
27
hinge
removal 64
spare part number 22, 28,
64
hinge cover
removal 64
spare part number 22, 64
ENWW
I
I/O address specifications 93
infrared emitter, spare part
number 26, 29
infrared lens 11
interrupt specifications 92
inverter
illustrated 22
removal 43, 44
spare part number 22, 28,
43
J
jacks
audio-in 11
audio-out 11
audio-out S/PDIF 11
headphone 11
microphone 11
modem 13
network 13
RJ-11 13
RJ-45 13
S-Video-out jack 13
K
keyboard
product description 3
removal 58
spare part numbers 19, 29,
58
keyboard components 9
keypad keys 9
keys
embedded numeric keypad 9
esc 9
fn 9
function 9
Windows applications 9
Windows logo 9
L
language support 83, 86
LED board cable, illustrated 24
left-side components 13
light components 6
lights
battery 6, 11
caps lock 6
drive 6, 11
num lock 6
ENWW
optical drive 12
power 6, 11
volume down 6
volume mute 6
volume up 6
wireless 11
next/fast forward button 8
num lock light 6
M
main menu 85
mass storage devices, spare part
numbers 25
media button 7
memory map specifications 95
memory module
product description 1
removal 47
spare part numbers 21, 30,
47
memory/WLAN module
compartment 15
memory/WLAN module
compartment cover
illustrated 23
removal 48
microphone
location 5
product description 2
removal 65
spare part number 22, 28,
65
microphone jack
location 11
pin assignments 121
model name 1
modem jack
location 13
pin assignments 123
modem module, product
description 2
monitor port
location 13
pin assignments 122
mouse, spare part numbers 26,
28
N
navigating in the Setup Utility
network jack
location 13
pin assignments 123
84
O
operating system, product
description 3
optical drive
location 12
precautions 34
product description 2
removal 52
spare part numbers 21, 25,
52
specifications 90
optical drive light 12
P
packing guidelines 36
password clearing 38
passwords 86
plastic parts 33
Plastics Kit
contents 23
spare part number 20, 23,
29
play/pause button 8
pointing device
components 10
product description 3
ports
1394 14
external monitor port 13
HDMI 13
monitor port 13
product description 2
Universal Serial Bus (USB) 12,
13
power button 7
power button board
removal 57
spare part number 19, 28,
57
power button board cable,
illustrated 24
power connector 12
power cord set requirements 125
power cord, spare part
numbers 26, 27
power light 6, 11
Index 135
power requirements, product
description 3
power-on password 86
previous/rewind button 7
processor
product description 1
removal 80
spare part numbers 20, 30,
80
product description
audio 2
camera 2
chipset 1
diskette drive 2
display panel 1
docking support 3
Ethernet 2
external media cards 2
graphics 1
hard drives 1
keyboard 3
memory module 1
microphone 2
modem module 2
operating system 3
optical drives 2
pointing device 3
ports 2
power requirements 3
processors 1
product name 1
security 3
serviceability 3
wireless 2
product name 1
R
rear component 13
recovery discs 117
recovery partition, deleting 120
recovery, system 119
remote control, spare part
numbers 26, 28, 29
removal/replacement
preliminaries 33
procedures 39
restore points 116
RF input adapter cable, spare part
number 26, 28
right-side components 12
136 Index
RJ-11 jack
location 13
pin assignments 123
RJ-45 jack
location 13
pin assignments 123
RTC battery
removal 49
spare part number 21, 31,
49
Rubber Kit, spare part
number 20, 28, 47
S
S-Video-out jack
location 13
pin assignments 124
Screw Kit
contents 97
spare part number 27, 28
screw listing 97
secondary hard drive self test 86
security cable slot 13
Security menu 86
security, product description 3
selecting in the Setup Utility 84
serial number 17, 39
service considerations 33
serviceability, product
description 3
Setup Utility
changing the language 83
Diagnostics menu 86
displaying system
information 84
Main menu 85
navigating 84
overview 83
Security menu 86
selecting 84
starting 83
System Configuration menu 86
using advanced features 85
software
reinstalling 118
updating 120
speaker assembly
removal 56
spare part number 20, 28,
56
speakers 7
specifications
computer 87
display 88
DVD/CD-RW Combo Drive 90
DVD±RW and CD-RW Combo
Drive 90
hard drive 89
I/O addresses 93
interrupts 92
memory map 95
optical drive 90
system DMA 91
static-shielding materials 37
stop button 8
switch cover
removal 54
spare part number 19, 31,
54
system board
removal 74
spare part number 20, 30,
74
System Configuration menu 86
system DMA 91
system information 84, 85
system memory map 95
T
thermal material, replacement 79
tools required 33
top components 6
top cover
removal 66
spare part numbers 19, 30,
66
top cover trim
removal 69
spare part number 20, 28,
69
TouchPad 10
TouchPad buttons 10
TouchPad light 10
TouchPad on/off button 10
TouchPad scroll zone 10
transporting guidelines 36
TV tuner antenna, spare part
number 26, 29
TV tuner, spare part number 26,
29
ENWW
U
Universal Serial Bus (USB) port
locations 12, 13
pin assignments 124
unknown password 38
USB digital drive, spare part
number 26, 27
USB/power connector board
removal 73
spare part number 20, 31,
73
USB/power connector board cable
illustrated 24
removal 76
V
vents 13, 15
video memory 86
volume down light 6
volume mute button 8
volume mute light 6
volume scroll zone 8
volume up light 6
W
Windows applications key 9
Windows logo key 9
wireless antenna
removal 64
spare part numbers 22, 28,
31, 65
Wireless Antenna Kit, spare part
numbers 22, 28, 31, 65
wireless light 11
wireless switch 11
wireless, product description 2
WLAN device
spare part numbers 28
WLAN module
removal 50
spare part numbers 20, 50
workstation guidelines 36
ENWW
Index 137
138 Index
ENWW