Download Sharp LC-15S4U Service manual
Transcript
LC-15S4U-S SERVICE MANUAL S75L9LC15S4US LCD COLOR TELEVISION MODEL LC-15S4U-S In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS Page » IMPORTANT SERVICE SAFETY PRECAUTION .........................................................................................2 » SPECIFICATIONS ........................................................................................................................................5 » OPERATION MANUAL .................................................................................................................................6 » DIMENSIONS ...............................................................................................................................................8 » REMOVING OF MAJOR PARTS ..................................................................................................................9 » ADJUSTING PROCEDURE OF EACH SECTION ..................................................................................... 13 » PUBLIC MODE SETTING PROCEDURE ..................................................................................................23 » TROUBLE SHOOTING TABLE ..................................................................................................................28 » MAJOR IC INFORMATIONS ...................................................................................................................... 32 » BLOCK DIAGRAM ......................................................................................................................................34 » OVERALL WIRING DIAGRAM ...................................................................................................................36 » DESCRIPTION OF SCHEMATIC DIAGRAM ............................................................................................. 38 » SCHEMATIC DIAGRAM ËR/C, LED Unit ..........................................................................................................................................39 ËMAIN Unit .................................................................................................................................................40 ËANALOG Unit ...........................................................................................................................................50 » PRINTED WIRING BOARD ASSEMBLIES ................................................................................................60 » REPLACEMENT PARTS LIST.................................................................................................................... 73 » PACKING OF THE SET ..............................................................................................................................83 SHARP CORPORATION This document has been published to be used for after sales service only. The contents are subject to change without notice. LC-15S4U-S IMPORTANT SERVICE SAFETY PRECAUTION Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: • Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resistor. • Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor. All checks must be repeated with the AC cord plug connection reversed. (If necessary, a nonpolarized adaptor plug must be used only for the purpose of completing these checks.) Any reading of 0.75V peak (this corresponds to 0.5 mA. peak AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the monitor to the owner. WARNING 1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. A V CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE REPLACE ONLY WITH SAME TYPE F3701 (2.5A, 250V), F3702 (2.0A, 250V), F6501 (1.6A, 250V) AND F6502 (1.6A, 250V) FUSE. BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard) Before returning the receiver to the user, perform the following safety checks: 1. Inspect all lead dress to make certain that leads are not pinched, and check that hardware is not lodged between the chassis and other metal parts in the receiver. 2. Inspect all protective devices such as non-metallic control knobs, insulation materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc. 3. To be sure that no shock hazard exists, check for leakage current in the following manner. • Plug the AC cord directly into a 110~240 volt AC outlet, and connect the DC power cable into the receiver's DC jack. (Do not use an isolation transformer for this test). • Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground. DVM AC SCALE 1.5k ohm 10W 0.15 µF TEST PROBE TO EXPOSED METAL PARTS CONNECT TO KNOWN EARTH GROUND 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 SAFETY NOTICE and shaded areas in the Replacement Parts Lists and Schematic Diagrams. For continued protection, replacement parts must be identical to those used in the original circuit. The use of substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire or other hazards. Many electrical and mechanical parts in LCD television have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by " å" 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123 123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123 2 LC-15S4U-S PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ë La réparation ne peut être effectuée que par un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. exposées du coffret et une terre connue comme une conduite électrique ou une prise de terre branchée à la terre. • Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour mesurer la chute de tension CA en travers de la résistance. • Toucher avec la sonde d'essai les pièces métalliques exposées qui présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson, etc.) et mesurer la chute de tension CA en travers de la résistance. Toutes les vérifications doivent être refaites après avoir inversé la fiche du cordon d'alimentation. (Si nécessaire, une prise d'adpatation non polarisée doit être utilisée dans le but de terminer ces vérifications.) La tension de pointe mesurèe ne doit pas dépasser 0.75V (correspondante au courant CA de pointe de 0.5mA). Dans le cas contraire, il y a une possibilité de choc électrique qui doit être supprimée avant de rendre le récepteur au client. AVERTISSEMENT 1. Pour la sécurité continue, n'entreprendre aucune modification de tout circuit. 2. Débrancher l'alimentation CA avant la réparation. A V PRECAUTION: POUR LA PROTECTION CONTINUE CONTRE LES RISQUES D'INCENDIE, REMPLACER LE FUSIBLE PAR UN FUSIBLE DE MEME TYPE F3701 (2.5A, 250V) F3702 (2.0A, 250V), F6501 (1.6A, 250V) et F6502 (1.6A, 250V). AVANT DE RENDRE LE RECEPTEUR A L’UTILISATEUR (Incendie et choc électrique) Avant de rendre le récepteur à l'utilisateur, effectuer les vérifications suivantes. 1. Inspecter tous les faisceaux de câbles pour s'assurer que les fils ne soient pas pincés ou qu'un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur. 2. Inspecter tous les dispositifs de protection comme les boutons de commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux de résistance-capacité, les isolateurs mécaniques, etc. 3. S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la fuite de courant, de la facon suivante: • Brancher le cordon d'alimentation directem-ent à une prise de courant de 110-240V. (Ne pas utiliser de transformateur d'isolation pour cet essai). • A l'aide de deux fils à pinces, brancher une résistance de 1.5kΩ 10 watts en parallèle avec un condensateur de 0.15µF en série avec toutes les pièces métalliques DVM ECHELLE CA 1.5k ohm 10W 0.15 µF SONDE D'ESSAI AUX PIECES METALLIQUES EXPOSEES BRANCHER A UNE TERRE CONNUE 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 AVIS POUR LA SECURITE pièces électriques qui présentent ces particularités sont De nombreuses pièces, électriques et mécaniques, dans identifiées par la marque " å " et hachurées dans la liste les téléviseurs de l'afficharge à cristaux liquides des pièces de remplacement et les diagrammes présentent des caractéristiques spéciales relatives à la schématiques. sécurité. Pour assurer la protection, ces pièces doivent être Ces caracténstiques ne sont souvent pas évidentes à vue. identiques à celles utilisées dans le circuit d'origine. Le degré de protection ne peut pas être nécessairement L'utilisation de pièces qui n'ont pas les mêmes augmentée en utilisant des pièces de remplacement caractéristiques que les pièces recommandées par étalonnées pour haute tension, puissance, etc. l'usine, indiquées dans ce manuel, peut provoquer des Les pièces de remplacement qui présentent ces électrocutions, incendies ou autres accidents. caractéristiques sont identifiées dans ce manuel; les 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 3 LC-15S4U-S Precautions for using lead-free solder 1 Employing lead-free solder "All PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: LFa Indicates lead-free solder of tin, silver and copper. 2 Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks. As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area. 3 Soldering As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead solder by 40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition. Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as required. If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it. When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper. Be careful when replacing parts with polarity indication on the PWB silk. Lead-free wire solder for servicing Part No, ★ Description ZHNDAi123250E J φ0.3mm 250g(1roll) ZHNDAi126500E J φ0.6mm 500g(1roll) ZHNDAi12801KE J φ1.0mm 1kg(1roll) 4 Code BL BK BM LC-15S4U-S SPECIFICATIONS Items LCD panel Number of dots Video color systems TV Standard (CCIR) TV Tuning System TV function STEREO CATV Y/C FILTER Brightness Viewing angles Audio amplifier Speakers INPUT1 INPUT2 Terminals INPUT3/OUTPUT Antenna Headphone OSD language Power supply Power consumption Display only Display with stand Operating temperature Weight Model LC-15S4U 15" Advanced Super View & BLACK TFT LCD 921,600 dots VGA N358, N443, PAL, PAL-M, PAL-N, SECAM, PAL-60 NTSC/PAL-M/PAL-N PLL 181 ch. MTS+SAP 125 ch. 3-LINE COMB FILTER 430 cd/m2 H: 170° V: 170° 2.1 W × 2 1 3/16 × 2 61/64 in. (3 × 7.5 cm), 2 pcs. Mini-jack for stereo (ø3.5 mm), COMPONENT-IN AUDIO-IN, VIDEO-IN, S-VIDEO-IN AUDIO-IN, VIDEO-IN/AUDIO-OUT, VIDEO-OUT F-Type Mini-jack for stereo (ø3.5 mm) English/Spanish/French DC 12V, AC 110-240V, 50/60Hz (AC adapter), AC 110-125V (AC cord) 36 W (0.2 W standby): AC 120V 31 W: DC 12V 7.9 lbs./3.6 kg 9.5 lbs./4.3 kg +32°F to +104°F (0°C to +40°C) ËAs a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for the LCD TV set improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units. 5 6 Remote sensor POWER/WAKE UP TIMER indicator lights up green when the power is on, and red when in the standby mode (the indicator will not light when the main power is off), and orange when the wake-up timer is set (the indicator will light when in the standby mode). POWER/WAKE UP TIMER indicator The OPC indicator lights up green when "OPC" is set to "ON". OPC (Optical Picture Control) indicator Plug the headphone mini-plug into the Headphone jack located on the front of the main unit. HEADPHONE jack To change the vertical angle of the LCD TV set, tilt the screen up to 2.5 degrees forward or 10 degrees backward. Please adjust the angle so that the LCD TV set can be watched most comfortably. Tilt the display by grabbing onto the carrying handle while securely holding down the stand with your other hand. How to adjust the angle Adjust the sound volume using VOL ( + ) / ( – ) on the remote control. VOLUME 20 • Headphones are not included in the supplied accessories. • No sound is heard from the main unit speakers when a headphone mini-plug is connected into the HEADPHONE jack. • Do not set the volume at a high level. Hearing experts advise against extended listening at high volume levels. Headphones " On-screen display Ë Plug the headphone mini-plug into the HEADPHONE jack located on the front of the main unit. Listening with Headphones • INPUT, CH ( )/( ), VOL (–)/(+) and MENU on the main unit have the same functions as the same buttons on the remote control. Fundamentally, this operation manual provides a description based on operation using the remote control. OPC (Optical Picture Control) sensor Speaker CH (Channel) INPUT ( )/( ) VOL (Volume) POWER MENU (–)/(+) Upper control panel Controls Part Names of the Main Unit VIDEO POWER INPUT (DC 12V) Y PB PR AUDIO (L/R) INPUT1 (COMPONENT) ANT. (Antenna terminal) INPUT2 INPUT3/ OUTPUT S-VIDEO VIDEO AUDIO (L) AUDIO (R) AUDIO (L) AUDIO (R) How to Fix the Cables Carrying handle Push the two hooks sideways to the left to open the cover. Cable clamp • Secure cables and cords with the supplied cable clamp so that they do not get caught when mounting the cover. * Using the Kensington Lock • This LCD TV set has a Kensington Security Standard slot for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the LCD TV set. Round lock for Kensington Security Standard slot* Rear View Terminals LC-15S4U-S OPERATION MANUAL MTS Selects audio settings. VOL (+)/(–) Sets the volume. AUDIO ONLY Outputs audio without screen image. MUTE Mutes the sound. ENTER Executes a command. MENU RETURN Returns to the previous screen. SLEEP Sets the sleep timer. PIC.FLIP Sets the orientation of the picture. POWER Switches the Liquid Crystal Television power on or standby. Part Names of the Remote Control Channel Select Sets the channel. CH ( )/( ) Selects a channel. FLASHBACK Returns to the previous channel. CC Displays Closed Caption subtitles. INPUT Switches the input source between INPUT1, INPUT2, INPUT3 and TV mode. MENU Displays the menu screen. ' / " / \ / | (Cursor control) Selects a desired item on the screen. BACKLIGHT Adjusts the brightness of the screen. AV MODE Selects preferred AV MODE. DISPLAY Displays the receiving channel and the current time for 10 seconds. Installing Batteries in the Remote Control Caution! Ë Slide the cover while pressing the ( ) part. Open the battery cover. 2 Ë Place batteries with their terminals corresponding to the (+) and (–) indications in the battery compartment. Insert two “AAA” size batteries. 3 Ë Engaging the lower claw with the remote control, close the cover. Close the battery cover. Ë Improper use of batteries can result in a leakage of chemicals and/or explosion. Be sure to follow the instructions below. • Place batteries with their terminals corresponding to the (+) and (–) indications. • Different types of batteries have different characteristics. Do not mix batteries of different types. • Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries and/or cause old batteries to leak chemicals. • Remove batteries as soon as they are depleted. Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe it off with a cloth. • The batteries supplied with the LCD TV set may have a shorter operating time due to storage conditions. • If the remote control is not to be used for a long period of time, remove the batteries from the remote control. Precautions regarding batteries 1 Before using the LCD TV set for the first time, install the two "AAA" size batteries supplied in the remote control. When the batteries become depleted and the remote control fails to operate, replace the batteries with new "AAA" size batteries. Preparation LC-15S4U-S 7 LC-15S4U-S DIMENSIONS Unit: inch (mm) 10 25/32 (274) 4 11/64 (106) 1 13/16 (46) 14 19/64 (363) 2 35/64 (65) 14 31/64 (368) 1 37/64 (40) 9 19/64 (236) 9 3/32 (231) 14 7/8 (378) 13 19/64 (338) 12 1/8 (308) 4 23/64 (111) 7 1/8 (181) 3 /16 (100) 2 3/4 (70) 3 15/16 (100) 15 8 LC-15S4U-S REMOVING OF MAJOR PARTS 1. Remove the stand cover fixing screws (1 pc.). 2. Remove the stand fixing screws (4 pcs.). 3. Remove the carrying handle fixing screws (4 pcs.). 4. Remove the terminal cover. 5. Remove the terminal screws (1 pc.). 6. Remove the cabinet B fixing screws (5 pcs.). 7. Remove the cabinet B after opening from the direction of an arrow. 8. Disconnect all the connectors from all the PWBs. Cabinet B Terminal Cover Cabinet A 6 4 5 Carrying Handle 7 3 2 Stand 1 Stand Cover Analog PWB P6500 P3401 P6501 8 P3402 SC3401 P3702 8 P3703 SC701 SC2001 8 8 SC1203 CN1 SC1202 SC1201 8 P4001 CN3 R/C, LED PWB CN2 8 Main PWB 9 LC-15S4U-S 9. Remove the 4 lock screws from the analog PWB, and undo the claws a and b. Detach the chassis frame (left) from the analog PWB by pulling out the terminals. In the same way, undo the claws c and d, and detach the chassis frame (right) from the analog PWB by pulling out the terminals. 10. Remove the 3 lock screws from the main PWB, and undo the claws e and f. Detach the main PWB by lifting the area around the claws and pulling the PWB out. Note: When detaching the main PWB and analog PWB, be careful not to break the PWB-fixing claws. 11. Remove the R/C, LED PWB fixing screws (2 pcs.) 12. Remove the stand angle fixing screws (4 pcs.) 13. Remove the 3 lock screws each from the right and left speakers and take out both the speakers. 14. Remove the LCD panel unit fixing screw (1 pc). 9 10 10 a c Analog PWB b Main PWB f e d Chassis Frame (R) Chassis Frame (L) 14 Speaker (L) Speaker (R) 13 13 R/C, LED PWB 11 Stand Angle 10 12 LC-15S4U-S » Precautions in handling the LCD panels 1. Work in a clean room (with humidities below 50%). 2. Be sure to wear an anti-static armband. 3. Handle the panels on an electro-conductive mat. 4. Be careful not to fall, shake and shock the panels. 15. Detach the LCD panel. 16. Detach the four reflection mirrors. 17. Detach the reflection/deflection sheet and diffusion sheets. 18. Detach the two multi reflection sheets. 19. Remove the lamp unit. 20. Detach the light guide panel. 21. Detach the reflection sheet. Back Shield (PSLDMA557WJFW) 21 20 19 18 17 Reflection Mirror (L), x2 (PMiR-A059WJZZ) 16 Reflection Sheet (PSHEPA277WJZZ) Light Guide Panel (PGiDMA015WJZZ) Lamp Unit (KLMP-A099WJZZ) Multi Reflection Sheet, x2 (PSHEP0307CEZZ) 15 15" LCD Panel Unit Diffusion Sheet, x2 (PSHEP0283CEZZ) Reflection/deflection Sheet (PSHEPA268WJZZ) Reflection Mirror (S), x2 (RMiR-A060WJZZ) 11 LC-15S4U-S »Precautions in servicing the B side (backside) of the main PWB unit 1. Disconnect the FFC from between the main PWB (SC1202) and LCD panel unit (CN1), and then connect the service-specific extension FFC (flat cable) (QCNW-B784WJZZ). 2. Disconnect the FFC from between the main PWB (SC1201) and LCD panel unit (CN2), and then connect the service-specific extension FFC (flat cable) (QCNW-A556WJZZ). 3. Disconnect the FFC from between the main PWB (SC1203) and LCD panel unit (CN3), and then connect the service-specific extension FFC (flat cable) (QCNW-A555WJZZ). 4. Remove the lock screws from the main PWB, detach the PWB from the chassis frame, and then turn it over to service. Analog PWB Main PWB (Side-B) CN1 SC1202 SC1203 3 R/C, LED PWB Step 1 2 3 Part No. QCNW-B784WJZZ QCNW-A556WJZZ QCNW-A555WJZZ 1 SC1201 2 CN3 CN2 Main PWB Description Extension Cable 30-pin Main (SC1202)-LCD Panel (CN1) Extension Cable 50-pin Main (SC1201)-LCD Panel (CN2) Extension Cable 20-pin Main (SC1203)-LCD Panel (CN3) 12 LC-15S4U-S ADJUSTING PROCEDURE OF EACH SECTION The products have been factory-adjusted to the best settings. If any of them gets out of point or readjustment is needed due to a part replacement, take the following adjustment procedures. 1. Pre-adjustment preparations Keep the AC power cable directly plugged in a wall outlet. 2. Adjustment procedures » Power on (initialization) → Model number and screen size settings → Transfer of model-related data (I2C) to setting E2PROM » Common bias adjustment → TAMP adjustment → White balance (cut-off and gain) adjustment 3. Entering the adjustment process mode 3-1. Calling the adjustment process mode » Turn on the power and press the "ADJUST PROCESS" key on the remote controller. » For servicing, hold down the "INPUT" and "VOL (–)" keys at once, and turn on the power switch. ("K" appears at the top left onscreen to indicate that the adjustment process mode is on.) Press the "CH (Ù)" and "VOL (–)" keys at once. (The adjustment process mode screen shows up.) To quit the mode, turn off the power (using the power switch on the set or the remote controller). 4. Key operation ËBasic operation Selecting a receiving channel » Using the "CH (ù)/(Ù)" keys, select an actual receiving channel. Instant press: Channels are selected one by one. Continuous press: The next receivable channel is searched and selected. » Various adjustments Using the "MENU", "cursor" and "VOL (+)/(–)" keys (on the set and the remote controller), adjust the settings of each item. » Using the "cursor UP/DOWN" keys, select an adjustment item. » Press the "MENU" key, and the adjustment items will be selected one after another (to the next item). When the item at the bottom of a page is selected, the press on the "MENU" key advances to the top item on the next page. » Even if any item is selected, the press on the "PRESET" key advances to the top item on the next page. Page 1 → Page 2 → Page 3 → Page 9 → Page 1 ... » Even if any item is selected, the press on the "MANUAL MEMORY" key moves back to the top item on the same page. » Using the "cursor RIGHT/LEFT" and "VOL (+)/(–)" keys, turn up and down the settings of a selected item. ËHierarchical shift » Press the "ENTER" key on any item other than I2C DATA on Page 4, the setting page of the item will show up. » To quit the setting page, press the "PREVIOUS SCREEN" key. 13 LC-15S4U-S 5. Take the following procedure when IC2009 (EEPROM) has been initialized or IC2001 (microprocessor) replaced. 5-1. Connect pins (81) and (82) of IC2001 (microprocessor) to GND, and turn on the power. 5-2. Make sure "15" (inches) is selected for the screen size. 5-3. Make sure the model number "A631B" is selected. (Onscreen display of adjustment process menu page 1) 0 2 3 4 5 6 M I O N D C E H L 2 3 E R R O R 0 1 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 S I Z E N O 1 1 A 4 P L I C V U – B 5 C H I P 6 E X T C O M O R E D E S E 6 3 1 1 T B 5 0 O F F 1 N T R O O L F F 6. Adjustments 6-1. Common bias adjustment 1) Select the "COM BIAS" mode on adjustment process menu page 2. Press the "cursor RIGHT/LEFT" keys to generate the built-in signal. 2) Using the "cursor RIGHT/LEFT" keys, readjust the setting so that flickering gets to minimum. 3) To quit the built-in signal pattern, press the "cursor UP/DOWN" keys. The adjustment process mode screen reappears. 6-2. TAMP adjustment 1) Feed the 100% white raster signal through the antenna input. 2) See if the "YDATA" reading on adjustment process menu page 2 is within the range in the table below. If not, select the "NTSC TAMP" item on the same page. Press the "cursor RIGHT/LEFT" keys to scroll down the item. Using the "cursor RIGHT/LEFT" keys again, readjust the "YDATA" reading to within the range shown below. Then add 6 to the "NTSC TAMP" setting and enter this value for "PAL-M TAMP" and "PAL-N TAMP". 3) Finally press the "cursor UP/DOWN" keys to return to the adjustment process mode screen. Model LC-15S4U-S Setting (NTSC) 155-158 Reference (Onscreen display of adjustment process menu page 2) 0 2 3 4 2 C T O A M M P 3 Y D A T 4 T A M P H 5 N T S T 6 P A L C – 7 P A L – 0 1 1 5 6 7 8 9 B I L A S 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 2 A 1 2 0 1 1 5 5 5 8 1 5 8 9 0 A M P M T A M P 9 6 N T A M P 9 6 8 Y data (white 100%) 14 LC-15S4U-S 6-3. White balance adjustment 1) Adjustment procedure Adjustment process menu page 3: RGB CUTOFF2, RGB-GAIN Feed the 40% white signal. Move the RCUTOFF2 and B-CUTOFF2 settings within ±30 to adjust the white balance. Next feed the 80% white signal. Reduce the GAIN settings of two stronger of the R, G and B colors by 30 to adjust the white balance. Taking these steps alternately, finely adjust the white balance. Reference: White balance process adjustment values (1) Test signal adjustment White 80% White 40% x y x y 0.282 0.291 0.262 0.269 Adjustment spec. ±0.004 ±0.004 ±0.002 ±0.002 [Adjusting with the bus] Cut-off (RGB CUTOFF2) Fix the G setting at 0. Vary the R and B settings. Gain (RGB GAIN): Reduce the settings of the two stronger colors. (The values are based on the Minolta CA-210.) Adjustable range ±30. Adjusted down to -30. 7. Factory settings 7-1. Making factory settings 1) Hold down the "INPUT" and "VOL (–)" keys at once, and turn on the power switch. "K" appears at the top left onscreen to indicate that the inspection process mode is on. 2) Hold down the "CH (ù)" and "VOL (+)" keys. A few seconds later, "SETTING COMPLETE" appears at the center of the screen. Now the factory settings are complete. U SETTING COMPLETE 15 LC-15S4U-S 7-2. Description of Factory Settings. Setting content/range MENU PICTURE AV MODE OPC BACKLIGHT CONTRAST BRIGHTNESS COLOR TINT SHARPNESS ADVANCED AUDIO SETUP RESET TREBLE BASS BALANCE RESET CH-SETTING STANDARD/DYNAMIC/DYNAMIC(FIXED)/MOVIE/GAME ON/OFF BRIGHT/NORMAL/DARK/VARIABLE COLOR TEMP. RED GREEN BLUE RESET EZ-SETUP LANGUAGE CH SETTING AUTO CLOCK START AIR/CABLE CH SEARCH CH MEMORY MTS CLOCK SET AUTO MANUAL DST TIME TIME DISPLAY INPUT3 IN/OUT V-CHIP BLOCK SECRET No. MPAA TV GUIDELINES CAN.ENGLISH RATINGS CAN.FRENCH RATINGS STATUS CLOSED CAPTION COLOR SYSTEM OPTION LANGUAGE VIEW MODE AUDIO ONLY BLUE SCREEN SLEEP TIMER WAKE UP TIMER 20 TIMER TIME CHANNEL VOL. NO SIGNAL OFF NO OPERATION OFF PICTURE FLIP G PG PG-13 R NC-17 X TV-Y TV-Y7 TV-G TV-PG TV-14 TV-MA BLOCK CONTENT C C8+ G PG 14+ 18+ G 8 ans+ 13 ans+ 16 ans+ 18 ans+ D L S V FV 1 (DARK) ~9 (NORMAL)~17 (BRIGHT) 0~60 -30~+30 -30~+30 -30~+30 -10~+10 USER/HIGH/MIDDLE/LOW -30~+30 -30~+30 -30~+30 YES/NO YES/NO -10~+10 -10~+10 -10(L)~+10(R) YES/NO YES/NO ENGLISH/ESPANOL/FRANCAIS ON/OFF ON/OFF YES/NO AIR/CABLE STEREO/SAP/MONO AUTO/MANUAL AUTO/[2]~[69] or [1]~[125] ON/OFF 12:00AM~11:59PM ON/OFF IN/OUT /OUT 4 digits input (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (BLANK)/BLOCK (BLANK)/BLOCK (BLANK)/BLOCK (BLANK)/BLOCK (BLANK)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK (NONE)/BLOCK ON/OFF OFF/CC1/CC2/T1/T2 N358/N443/PAL/PAL-M/PAL-N/SECAM/PAL60 (Only for N358/PAL-M/PAL-N in TV mode) ENGLISH/ESPANOL/FRANCAIS 4:3/16:9/ZOOM/STRETCH ON/OFF ON/OFF OFF/30/60/90/120/150MIN ON/OFF 12:00AM~11:59PM CH1~125/COMPONENT1/COMPONENT2 or AV1/AV2 0~60 ENABLE/DISABLE ENABLE/DISABLE NORMAL/MIRROR/ROTATE/UPSIDE DOWN (Items other than MENU) EZ SETUP ON 2ch LAST CHANNEL TV LAST TV/INPUT 2ch FLASH BACK SKIP DATA_CATV ALL SKIP SKIP DATA_AIR ALL SKIP VOLUME 20 LINE OUT LEVEL(VAO) 0 EDS CH (AUTO) 16 Initial Value DYNAMIC OFF VARIABLE (STANDARD) 17 30 0 0 0 0 MIDDLE 0 0 0 NO NO 0 0 0 NO YES ENGLISH ON ON YES AIR STEREO AUTO AUTO OFF 12:00AM ON IN Clear NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE BLANK BLANK BLANK BLANK BLANK NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE NONE OFF OFF (TV) N358 ENGLISH 4:3 OFF OFF OFF(Clear) OFF 12:00AM CH2 20 DISABLE DISABLE NORMAL (AV1) DYNAMIC (DYNAMIC) 17 45 0 +5 0 0 (AV2) DYNAMIC (COMPONENT1) DYNAMIC (DYNAMIC(FIXED) 17 60 0 +10 0 0 (MOVIE) 7 25 0 0 0 0 (UN BLOCK) (UN BLOCK) (UN BLOCK) (UN BLOCK) (UN BLOCK) (AV1) N358 (AV2) N358 (GAME) 9 30 0 0 0 0 LC-15S4U-S 8. Lamp error detection 8-1. Functional description This LCD color television has a function (lamp error detection) to be turned off automatically for safety when the lamp or lamp circuit is abnormal. If the lamp or lamp circuit is abnormal, or some other errors happen, and the lamp error detection is executed, the followings occur. 1 The main unit of television is turned off 5 seconds after it is turned on. (The power LED on the front side of TV turns from green to red.) 2 If the situation 1 happens 5 times sequentially, television can not be turned on. (The power LED remains red.) 8-2. Countermeasures 8-2-1. Check when turning off the lamp error detection When television is turned off by the lamp error detection mentioned above, it enters the adjustment process with the power LED red. Entering the adjustment process turns off the error detection and turns on TV. This enables the operation check to detect errors in the lamp or lamp circuit. Check whether "ERROR NO RESET" on line 4, page 1 of the adjustment process is 1 or more. If it is 1 or more, it indicates the lamp error detection was executed. 8-2-2. Resetting of the lamp error count After confirming that the lamp or lamp circuit is normal, reset the lamp error count. Select "ERROR NO RESET" on line 4, page 1 of the adjustment process and set the number to 0 using the "VOL (+)/(–)" keys. Page 1 of the adjustment process 1 MODEL INCH ERROR PUBLIC V–CHIP EXT SIZE NO RESET MODE CONTROL A631B 15 5 OFF 1 OFF Reset 0 VER ROM 1. X X A G AI B U X. X X X Afterwards, perform the operation check to confirm that the lamp error detection does not function. 17 LC-15S4U-S LIST OF THE ADJUSTMENT PROCESS MODE MENU For calling the adjustment process mode and keying in this mode, refer back to "ADJUSTING PROCEDURE OF EACH SECTION". ADJUSTMENT PROCESS 1st LEVEL ITEM DEFAULT TABLE Page No. Item Initial Function Value Response precautions on servicing (Do not change other items than designated.) BASIC SETTINGS 1 MODEL INCH SIZE A631B 15 MODEL NUMBER SELECT SCREEN SIZE SELECT (20-INCH AND 13/15-INCH SETTINGS NOT SWITCHABLE IN CASE OF DIFFERENT SYSTEMS) LAMP ERROR COUNT AND RESET HOTEL MODE SETTING VCHIP LINE MUTE SETTING BUS, UART OPEN NOT MODIFIABLE USED FOR ADJUSTMENT PROCESS INITIALIZATION, NOT MODIFIABLE FOR COMMON BIAS ADJUSTMENT Y LOWER LIMIT SETTING AT TAMP ADJUSTMENT DATA READ VALUE AT TAMP ADJUSTMENT Y UPPER LIMIT SETTING AT TAMP ADJUSTMENT TAMP ADJUSTMENT TAMP ADJUSTMENT TAMP ADJUSTMENT SEE THE ADJUSTMENT PROCEDURES. NOT USED SEE THE ADJUSTMENT PROCEDURES. NOT USED SEE THE ADJUSTMENT PROCEDURES. SEE THE ADJUSTMENT PROCEDURES. SEE THE ADJUSTMENT PROCEDURES. RED CUT-OFF ADJUSTMENT 2 GREEN CUT-OFF ADJUSTMENT 2 BLUE CUT-OFF ADJUSTMENT 2 WHITE BALANCE ADJUSTMENT 2 WHITE BALANCE ADJUSTMENT 2 WHITE BALANCE ADJUSTMENT 2 RGB γ COEFFICIENT SETTING SEE THE ADJUSTMENT PROCEDURES. SEE THE ADJUSTMENT PROCEDURES. SEE THE ADJUSTMENT PROCEDURES. SEE THE ADJUSTMENT PROCEDURES. SEE THE ADJUSTMENT PROCEDURES. SEE THE ADJUSTMENT PROCEDURES. NOT USED I2C BUS CONTROL IC DATA WRITE AND READ WRITE AND READ EXECUTED SHIFT TO THE SOUND ADJUSTMENT PAGE SHIFT TO THE DVP ADJUSTMENT PAGE SHIFT TO THE TUNER ADJUSTMENT PAGE SHIFT TO THE OTHER ADJUSTMENT PAGE NOT USED NOT USED USE ENTER KEY TO GO TO THE SOUND ADJUSTMENT PAGE. USE ENTER KEY TO GO TO THE TC ADJUSTMENT PAGE. USE ENTER KEY TO GO TO THE TUNER ADJUSTMENT PAGE. USE ENTER KEY TO GO TO THE OTHER ADJUSTMENT PAGE. ERROR NO RESET 0 PUBLIC MODE OFF V-CHIP 1 EXT CONTROL ON ROM AND GAIBU VERSION NUMBERS DISPLAYED AT THE BOTTOM. VIDEO ADJUSTMENT 2 COM BIAS TAMP L YDATA TAMP H NTSC TAMP PAL-M TAMP PAL-N TAMP 120 155 — 158 90 96 96 BACKGROUND ADJUSTMENT R CUTOFF2 3 G CUTOFF2 B CUTOFF2 R-GAIN G-GAIN B-GAIN RGB GAMMA 0 0 0 0 0 0 1.0 OTHER CASES. DATA REWRITE AND READJUSTMENT REQUIRED WHEN INITIALIZED. SEE THE LAMP ERROR DETECTION. NOT USED NOT USED NOT USED TABLE OF VARIOUS SETTINGS 9 I2C DATA I2C DATA SOUND DVP TUNER OTHERS 0 WAIT — — — — AUDIO ADJUSTMENT PROCESS SPECIFICATIONS Page No. Item AUDIO ADJUSTMENT SOUND1 VOLUME MSP DATA MSP DATA CARRIER MUTE IGR THR Initial Value 20 0 WAIT ON 12D Function SOUND VOLUME AUDIO IC MSP DATA WRITE AND READ WRITE AND READ EXECUTED AUDIO OUTPUT SETTING WITHOUT TV SYNC IGR THRESH LEVEL Response precautions on servicing (Do not change other items than designated.) NOT USED NOT USED NOT USED NOT USED NOT USED AUDIO ADJUSTMENT SOUND2 PRESCALE SCART PRESCALE FM/AM-M 27 31 PRE-SCALE SETTING (EXTERNAL INPUT) NOT USED PRE-SCALE SETTING (TV) NOT USED 18 LC-15S4U-S Page No. Initial Item Function Value Response precautions on servicing (Do not change other items than designated.) AUDIO ADJUSTMENT SOUND3 BAND1 MIN BAND1 CNT BAND1 MAX BAND2 MIN BAND2 CNT BAND2 MAX BAND3 MIN TV OTHER TV OTHER TV OTHER TV OTHER TV OTHER TV OTHER TV OTHER -0350 -0350 +0450 +0450 +1200 +1200 +0100 +0100 +0400 +0400 +0700 +0700 -0225 -0225 EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED TV OTHER TV OTHER TV OTHER TV OTHER TV OTHER TV OTHER -0825 -0825 -0525 -0525 -0225 -0225 -1200 -1200 -0550 -0550 +0250 +0250 EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) EQUALIZER SETTING (WITH TV INPUT) EQUALIZER SETTING (WITH OTHER INPUT THAN TV) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED AUDIO ADJUSTMENT SOUND4 BAND4 MIN BAND4 CNT BAND4 MAX BAND5 MIN BAND5 CNT BAND5 MAX AUDIO ADJUSTMENT PROCESS SPECIFICATIONS Page No. Item VIDEO ADJUSTMENT DVP1 DVP DATA 0000 F0 ------(----) DVP TEST PATTERN VCDOFFSET VCDWINDOW VIDEO ADJUSTMENT DVP3 N358 TV CONTRAST N358 AV CONTRAST N358 TV BRIGHT N358 AV BRIGHT N358 TV COLOR N358 AV COLOR N358 TV TINT N358 AV TINT N358 TV SHARP V N358 AV SHARP V N358 TV SHARP H1 N358 AV SHARP H1 N358 TV SHARP H2 N358 AV SHARP H2 Initial Value Function Response precautions on servicing (Do not change other items than designated.) 0 15 30 DVP-RELATED GENERAL-PURPOSE VARIABLE SETTINGS TEST PATTERN SELECT VERTICAL COUNT-DOWN MINIMUM OSCILLATION CYCLE VERTICAL COUNT-DOWN SYNC RANGE NOT USED SEE THE ADJUSTMENT PROCESS MODE TEST PATTERNS. NOT USED NOT USED 128 128 128 128 37 37 128 128 100 100 200 200 150 160 IMAGE SETTING (TV) IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (TV) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (TV) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (TV) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (TV) V PICTURE QUALITY SETTING (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 1 (TV) H PICTURE QUALITY SETTING 1 (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 2 (TV) H PICTURE QUALITY SETTING 2 (COMPOSITE, S VIDEO) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED 19 LC-15S4U-S Page No. Item Initial Value Function Response precautions on servicing (Do not change other items than designated.) VIDEO ADJUSTMENT DVP4 N443 AV CONTRAST N443 AV BRIGHT N443 AV COLOR N443 AV TINT N443 AV SHARP V N443 AV SHARP H1 N443 AV SHARP H2 128 128 37 128 100 200 160 IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 1 (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 2 (COMPOSITE, S VIDEO) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED VIDEO ADJUSTMENT DVP5 PAL AV CONTRAST PAL AV BRIGHT PAL AV COLOR PAL AV TINT PAL AV SHARP V PAL AV SHARP H1 PAL AV SHARP H2 128 128 37 128 100 200 160 IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 1 (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 2 (COMPOSITE, S VIDEO) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED VIDEO ADJUSTMENT DVP6 SECAM AV CONTRAST SECAM AV BRIGHT SECAM AV COLOR SECAM AV TINT SECAM AV SHARP V SECAM AV SHARP H1 SECAM AV SHARP H2 128 128 37 128 100 200 160 IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 1 (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 2 (COMPOSITE, S VIDEO) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED VIDEO ADJUSTMENT DVP7 PAL60 AV CONT PAL60 AV BRIGHT PAL60 AV COLOR PAL60 AV TINT PAL60 AV SHARP V PAL60 AV SHARP H1 PAL60 AV SHARP H2 128 128 37 128 100 200 160 IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 1 (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 2 (COMPOSITE, S VIDEO) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED VIDEO ADJUSTMENT DVP8 PAL-M TV CONTRAST PAL-M AV CONTRAST PAL-M TV BRIGHT PAL-M AV BRIGHT PAL-M TV COLOR PAL-M AV COLOR PAL-M TV TINT PAL-M AV TINT PAL-M TV SHARP V PAL-M AV SHARP V PAL-M TV SHARP H1 PAL-M AV SHARP H1 PAL-M TV SHARP H2 PAL-M AV SHARP H2 128 128 128 128 37 37 128 128 100 100 200 200 150 160 IMAGE SETTING (TV) IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (TV) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (TV) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (TV) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (TV) V PICTURE QUALITY SETTING (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 1 (TV) H PICTURE QUALITY SETTING 1 (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 2 (TV) H PICTURE QUALITY SETTING 2 (COMPOSITE, S VIDEO) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED 20 LC-15S4U-S Page No. Item Initial Value Function Response precautions on servicing (Do not change other items than designated.) VIDEO ADJUSTMENT DVP9 PAL-N TV CONTRAST PAL-N AV CONTRAST PAL-N TV BRIGHT PAL-N AV BRIGHT PAL-N TV COLOR PAL-N AV COLOR PAL-N TV TINT PAL-N AV TINT PAL-N TV SHARP V PAL-N AV SHARP V PAL-N TV SHARP H1 PAL-N AV SHARP H1 PAL-N TV SHARP H2 PAL-N AV SHARP H2 128 128 128 128 37 37 128 128 100 100 200 200 150 160 IMAGE SETTING (TV) IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (TV) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (TV) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (TV) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (TV) V PICTURE QUALITY SETTING (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 1 (TV) H PICTURE QUALITY SETTING 1 (COMPOSITE, S VIDEO) H PICTURE QUALITY SETTING 2 (TV) H PICTURE QUALITY SETTING 2 (COMPOSITE, S VIDEO) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED VIDEO ADJUSTMENT DVP10 525I CONT 525I BRIGHT 525I COLOR 525I TINT 525I SHARP V 525I SHARP H1 525I SHARP H2 525P CONT 525P BRIGHT 525P COLOR 525P TINT 525P SHARP V 525P SHARP H1 525P SHARP H2 133 128 52 128 100 160 160 119 147 52 128 100 120 120 IMAGE SETTING (TV) BRIGHTNESS SETTING (TV) COLOR DENSITY SETTING (TV) TINT SETTING (TV) V PICTURE QUALITY SETTING (TV) H PICTURE QUALITY SETTING 1 (TV) H PICTURE QUALITY SETTING 2 (TV) IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (TV) H PICTURE QUALITY SETTING 1 (TV) H PICTURE QUALITY SETTING 2 (TV) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED VIDEO ADJUSTMENT DVP11 625I CONT 625I BRIGHT 625I COLOR 625I TINT 625I SHARP V 625I SHARP H1 625I SHARP H2 625P CONT 625P BRIGHT 625P COLOR 625P TINT 625I SHARP V 625I SHARP H1 625I SHARP H2 133 128 52 128 100 160 160 133 128 52 128 100 120 120 IMAGE SETTING (TV) BRIGHTNESS SETTING (TV) COLOR DENSITY SETTING (TV) TINT SETTING (TV) V PICTURE QUALITY SETTING (TV) H PICTURE QUALITY SETTING 1 (TV) H PICTURE QUALITY SETTING 2 (TV) IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (TV) H PICTURE QUALITY SETTING 1 (TV) H PICTURE QUALITY SETTING 2 (TV) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED 21 LC-15S4U-S ADJUSTMENT PROCESS TUNER ITEM DEFAULT TABLE Page No. Item VIDEO ADJUSTMENT DVP12 1125I CONT 1125I BRIGHT 1125I COLOR 1125I TINT 1125I SHARP V 1125I SHARP H1 1125I SHARP H2 750P CONT 750P BRIGHT 750P COLOR 750P TINT 750P SHARP V 750P SHARP H1 750P SHARP H2 Initial Value Function Response precautions on servicing (Do not change other items than designated.) 128 128 52 128 100 100 100 128 128 92 128 100 100 100 IMAGE SETTING (TV) BRIGHTNESS SETTING (TV) COLOR DENSITY SETTING (TV) TINT SETTING (TV) V PICTURE QUALITY SETTING (TV) H PICTURE QUALITY SETTING 1 (TV) H PICTURE QUALITY SETTING 2 (TV) IMAGE SETTING (COMPOSITE, S VIDEO) BRIGHTNESS SETTING (COMPOSITE, S VIDEO) COLOR DENSITY SETTING (COMPOSITE, S VIDEO) TINT SETTING (COMPOSITE, S VIDEO) V PICTURE QUALITY SETTING (TV) H PICTURE QUALITY SETTING 1 (TV) H PICTURE QUALITY SETTING 2 (TV) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED 1.80 1.20 150 162 1 3 10 AFT VOLTAGE REFERENCE LEVEL (ALL BANDS) AFT VOLTAGE REFERENCE LEVEL (ALL BANDS) SYNC JUDGMENT THRESHOLD (TV) SYNC JUDGMENT THRESHOLD (TV) SYNC JUDGMENT THRESHOLD (EXTERNAL INPUT) SYNC JUDGMENT THRESHOLD (COLOR DIFFERENCE INPUT) DURATION UNTIL JUDGMENT OF NO EDS TIME DATA (SECONDS) NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED AFT FARTIME AFT NEARTIME AFT NEARMTIME AFT 1STEPTIME AFT CSYNCTIME SYNC ON SYNC WIDTH 50 30 10 10 50 10 1 CHANNEL PRESET TIME ADJUSTMENT 1 CHANNEL PRESET TIME ADJUSTMENT 2 CHANNEL PRESET TIME ADJUSTMENT 3 CHANNEL PRESET TIME ADJUSTMENT 4 CHANNEL PRESET TIME ADJUSTMENT 5 CHANNEL PRESET TIME ADJUSTMENT 6 CHANNEL PRESET TIME ADJUSTMENT 7 NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED DAC DATA — TUNER SETTINGS TUNER1 AFT UP AFT DOWN LSYNC HSYNC AVSYNC COMPSYNC EDS TEST TUNER SETTINGS TUNER2 OTHERS OTHERS1 OTHERS2 00--- DAC-RELATED GENERAL-PURPOSE VARIABLE SETTINGS L ERROR WAIT 15s LAMP ERROR DETECT WAIT TIME L ERROR H TIME 1.0s LAMP ERROR DETECT TIME TV AUTO GAIN OFF AUTO GAIN SETTING FOR TV PWM FREQ 150 DIMMER FREQUENCY SETTING (IN HZ) PWM DUTY 0 DIMMER DUTY SETTING OPC THRESHOLD 24 INPUT LEVEL THRESHOLD FROM BRIGHTNESS SENSOR STOP MODE TO OPERATION MODE HOTEL POWERFIX OFF USED FOR FIXED HOTEL MODE POWER ON COMP SYSTEM AUTO COMPONENT SIGNAL SELECT IN ADJUSTMENT PROCESS REMOCON CODE DISPLAYED AT THE BOTTOM 3D Y/C 3DY/C DATA 3DY/C DATA KIL CLOSED CAPTION 0 0 WAIT OFF 15 3D ON/OFF SETTING 3D YC DATA WRITE AND READ WRITE AND READ EXECUTED FORCED KILLER SETTING FOR SIGNAL WITHOUT COLOR BURST CLOSED CAPTION THRESH LEVEL 22 NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED NOT USED LC-15S4U-S PUBLIC MODE SETTING PROCEDURE 1. How to start Public Mode » There are the following two ways to get the public mode setup screen displayed. 1 In the adjustment process mode, turn on "PUBLIC MODE". Also press the "CH (ù)" and "VOL (+)" keys on the set at once and turn on the power. 2 1) Press the "INPUT" and "VOL (+)" keys on the set at once and turn on the power. 2) Get the password input screen displayed. Procedure » The input starts with the leftmost digit. » Use the numeric keys [1] thru [9] and [10/0] keys on the remote controller. The other keys are not acceptable. » With a numeric-key input, "–" will change to " ". The input position will move one digit to the right. » With all the 3 digits entered, the password will be verified. 3) The 3-digit password is now verified. The password [0] [2] [7] provides for the public mode screen. (This screen comes on with whatever adjustment process settings.) With any other passwords, the screen changes to the normal mode. 23 LC-15S4U-S 2. How to exit Public Mode There are the following ways to quit the public mode setup screen. » Turn off "PUBLIC MODE" in the adjustment process mode. (✩) ← This way alone is not for quitting the setup screen, but for quitting the mode itself. » Turn off the power with the "POWER" key. (★) » Select "ENTER". (★) » Move the cursor to "RESET" and press the "FLASHBACK" key. (Back to the normal mode screen)(✩) ★ ... "PUBLIC MODE" stays on in the adjustment process mode. ✩ ... The settings will be back to the factory ones. 3. Public Mode Setting Values » With the factory settings made, the public mode settings get initialized. (The adjustment process remains intact.) 4. Public Mode Menu The guidance is not displayed onscreen. Setup procedure » To move the cursor up and down, use the "cursor UP/DOWN" key (remote controller) and "CH (ù)/(Ù)" key (remote controller and set). » To change the settings, use the "cursor RIGHT/LEFT" key (remote controller) and "VOL (+)/(–)" key (remote controller and set). » To save new settings, keep the cursor at "Enter" and use the "cursor RIGHT/LEFT" key (remote controller) and "VOL (+)/(–)" key (remote controller and set). Public mode Power on fixed Maximum volume Volume fixed Volume fixed level RC button Panel button Menu button On screen display Input mode start Input mode fixed Reset [Variable [ 60 [Variable [ 20 [Respond [Respond [Respond [Yes [Normal [Variable ] ] ] ] ] ] ] ] ] ] Enter 24 LC-15S4U-S 5. On Setting Items * "EZ-SETUP" discussed below indicates "EZ-SETUP after the first power-on". (1) POWER ON FIXED Selection between "Variable" and "Fixed" (loop provided) Selection – (Variable) In "Fixed" setting, the power-off by the power key of the unit is invalidated and the image is kept being received. The power can be turned off by stopping the power supply from AC. Limit in Setting Refer to the "Power-On Fixed" sheet. None Exception Remarks » Selection of "FIXED" depends on use of STB etc. » In "Variable" setting, the power operation is in wait for 1 sec. and then turned off when the main power switch is off. » Display ON/OFF in hotel menu is controlled by adjustment process "HOTEL POWERFIX". Default Explanation (2) MAXIMUM VOLUME Adjustment from 0 to 60 (no loop) Selection 60 Default Sound volume can not be adjusted higher than the preset value. Explanation Limit in Setting » When the sound volume is set lower than 59, only figures are displayed and the sound volume bar is not displayed. » The maximum sound volume for ON-timer (Wake up timer) is limited also to the preset value. Exception » In the item "VOLUME" of adjustment process, the sound volume can be set freely irrespective of this setting. Remarks » In line output (sound volume variable), the sound volume can be adjusted from -60 to 0 irrespective of pre-adjusted value. » When the sound volume is set higher than the MAX setting by the adjusting process, the sound volume control operation is prohibited for turn-up and the sound volume should be turned down to MAX in this state. (3) VOLUME FIXED Selection Selection between "Variable" and "Fixed" (loop provided) Default Variable Sound volume is fixed and made invariable. Explanation Limit in Setting » The sound volume for the ON-timer (Wake up timer) is fixed also without display of menu. Besides, the setting is made impossible. (Basically, the menu is not displayed.) » The following keys become invalid: » Sound volume Up/Down (VOL +/-) [for both remote control and the unit] » Mute (MUTE) Exception » In the item "VOLUME" of adjustment process, the sound volume can be set freely irrespective of this setting. Remarks » In line output (sound volume variable), the sound volume can be adjusted from -60 to 0 irrespective of pre-adjusted value. » As for sound volume fixing and sound volume MAX level, the sound volume fixing has priority. » Once the sound volume has been changed by adjustment process, it should be set back to the sound volume preset by sound volume fixing level when the adjustment process ends . 25 LC-15S4U-S (4) VOLUME FIXED LEVEL Selection Default Explanation Limit in Setting Exception Remarks Adjustment from 1 to 60 (no loop) 10 The sound volume to be fixed by "Volume fixed" is determined. None None Setting is valid only when "Volume fixed" is selected for "fixed". (5) R/C BUTTON Selection Default Explanation Limit in Setting Exception Selection between "Respond" , "Limited" and "No respond" (loop provide) Respond Keys acceptable by remote control are limited or reception of keys can be prohibited. 1In "limited" setting, only power ON/OFF, sound volume '", tuning '" and BACKLIGHT (brightness sensor) are accepted. 2In "No respond" setting, all the keys (including the power key) are not accepted. » Adjustment process, factory setting, inspection process and hotel only keys are valid irrespective of setting. » All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting. » All the keys can be used also in the initial EZ-Setup after power-ON irrespective of setting. Remarks (6) PANEL BUTTON Selection between "Respond" and "No respond" (loop provide) Selection Respond Default All the operations by keys (except the power key) of the unit can be invalidated. Explanation Limit in Setting Exception » Inspection mode and hotel menu mode can be started irrespective of setting. » All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting. » In U.S.A model, all the keys can be used also in the initial EZ-Setup after power-ON irrespective of setting. Remarks (7) MENU BUTTON Selection between "Respond" and "No respond" (loop provide) Respond In "No respond" setting, the menu operation by the menu key of the remote control and the menu key of the unit are invalidated. Limit in Setting » ON-timer (Wakeup Timer) is turned OFF. » The following keys become invalid. Wake-up timer and clock setting keys and all of the direct change keys to menu display Exception » Inspection mode and hotel menu mode can be started irrespective of setting. » All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting. » All the keys can be used also in the initial EZ-Setup after power-ON irrespective of setting. Remarks Selection Default Explanation 26 LC-15S4U-S (8) ON SCREEN DISPLAY Selection between "Yes" , "Limited" (loop provide) Yes The following OSD displays are made ineffective. Displays of menu group, channel call, sound volume bar and direct key call Limit in Setting » ON-timer (Wake-up timer) is cleared and set to "OFF". » Set time of the OFF-timer (SLEEP TIMER) is cleared. » Setting of the no-signal power-OFF (AUTO POWER OFF) is cleared to "OFF". » Setting of the no-operation power-OFF is cleared to "OFF". » Keys falling under any of the following items become invalid. 1Appearance of screen changes and the sound changes. 2Personal functions which are hard to restore. Screen display, menu, OFF-timer, ON-timer, AV MODE, screen size switching, clock setting, treble emphasis, AUDIO ONLY, sound changeover, LANGUAGE, CLOSED CAPTION Others » Simple input switching is generated. Those which are restored soon after leaving as they are and may be requested for change by customer are not prohibited. Brightness sensor (BACKLIGHT) and PIC. FLIP Exception » Such a caution which is displayed independently is displayed as it is. Non-responding signal caution, V-Chip caution and power-ON fixing caution Remarks » When CC has already been ON, CLOSED CAPTION is displayed. Selection Default Explanation (9) INPUT MODE START Selection between "Normal" , "TV (CH~)" "INPUT 1/2/3" (loop provide) Normal In power-ON, the input source to be started or channel can be set. (In standard mode, the operation follows the last memory.) About options » All the input sources in the model are made selectable. » When the input/output switchable input source is selected and the input source is set to output, the setting of input/output switching is changed to input at the execution of hotel menu. In addition, the input/output switching by menu is prohibited. » In TV mode, the channel to be set follows the last memory and the content of the last memory is included in the notation by options. Ex.) TV (CH2), TV (CH4) etc. Limit in Setting » The display of channel setting menu and the channel setting operation are prohibited. Exception » In the start by "ON-timer (Wake-up timer)", the channel set by ON-timer (Wake-up timer) has priority. Remarks » In setting at "Normal", the setting of "Input mode fixed" is changed to "Variable" and selection should be prohibited. Selection Default Explanation (10) INPUT MODE FIXED Selection between "Variable" and "Fixed" (loop provide) – (Variable) The input mode is fixed at the input source or the channel set at the "Input mode start" in 9 and other input sources and channels can be made non-selectable. Limit in Setting » With the execution of hotel mode, the input source is forced to change to that set by "Input mode start" and the channel switching and input switching are prohibited thereafter. » ON-timer's (Wake-up timer) channel items are not displayed or the operation is prohibited. (Basically, they are not displayed.) » The following keys are invalidated. CH '", direct tuning button, FLASHBACK, input ~However, the keys (input switching and CH '" keys) of the unit for menu operation remain valid. None Exception Remarks » In the following case, setting is cancelled and mode is changed to "Variable". 1When the setting of "Input mode start" is set to "Standard (Normal)" Selection Default Explanation 27 28 Check the load of IC701 thru IC703 and their peripheral circuits. Yes Are the output voltages of IC701 thru IC703 as specified? Yes Are the secondary +35V, +9V, +5.3V, -12V and -7V outputs of T701 as specified? Yes Is DC12V applied at pins (6) and (7) of T701 and pin (8) of IC701 thru IC703? Yes Is DC12V applied at to F3701 and F3702? Yes Are F3701 and F3702 as specified? No No No No No Check the load side of IC701 thru IC703. Yes Is pin (10) of IC701 thru IC703 at "H"? Check the secondary load of T701. Yes Is the primary oscillation waveform of T701 as specified? Check the connections between P3702 and SC701 and their peripheral circuits. Check P3701 and its peripheral circuits as well as the built-In AC power supply. Check the primary side of T701, and IC701 thru IC703 and their peripheral circuits. Yes Disconnect F3701 and F3702. Is the load side short-circuited? No No Yes Check the connections between pin (19) of IC2001 and pin (3) of P3701. Check the primary peripheral circuits and secondary load of T701. Replace F3701 and F3702. Check the built-in AC power unit, inverter unit and fluorescent lamp, and replace as required. Yes Does pin (185) of IC801 oscillate? Is pin (187) of IC801 at "H" or with pulse signal? Yes Is pin (70) of IC2001 at "H"? Yes No Check the line in question, IC801 and its peripheral circuits. Check the line in question, IC2001 and its peripheral circuits. Fluorescent lamp light-up failure Make sure the microprocessor's adjustment process menu settings are as specified. No video and audio output (no power supply) LC-15S4U-S TROUBLE SHOOTING TABLE Check the line in question. Are the input and output of IC3402 as specified? Check the LCD panel voltage and waveform. Check IC801 and its peripheral circuits. Yes No No Check IC3402 and its peripheral circuits. No TV, video 1 and 2 output Yes Are the input and output of IC801 as specified? No video output at all 29 Check the line in question. Yes Is the output of IC3402 as specified? Yes Is the input at pin (5) of IC3402 as specified? Yes Is the output at pin (19) of tuner as specified? Yes Are the voltages at pins (6), (7) and (9) of tuner as specified? No video 1 output No No No No Check IC3402 and its peripheral circuits. Check the line in question. Check the tuner and its peripheral circuits. Check the power line. Check the line in question. Yes Is the output of IC3402 as specified? Yes Is the input at pin (1) of IC3402 as specified? No No Check IC3402 and its peripheral circuits. Check the line in question. Check the line in question. Yes Is the output of IC3402 as specified? Yes Is the input at pin (3) of IC3402 as specified? No No Check IC3402 and its peripheral circuits. Check the line in question. No video 2 output Make sure the microprocessor's adjustment process menu settings are as specified. No TV output No video output Check the line in question. No S video output Check the D-Y, D-Pb and D-Pr lines of J3405. Are the inputs at pins (21), (33) and (44) of IC801 as specified? No component output LC-15S4U-S TROUBLE SHOOTING TABLE (Continued) 30 Check the lines from between pins (27) (Rch) and (28) (Lch) of IC3201 to pins (4) (Rch) and (2) (Lch) of IC3301. Yes Are the audio signal outputs at pins (27) (Rch) and (28) (Lch) of IC3201? Yes Are the oscillation waveforms at pins (71) and (72) of IC3201 as specified? Yes Are the following control signals fed as follows? Pin (2) of IC3201: SCL1 Pin (3) of IC3201: SDA1 Yes Is the supply voltage of each circuit as follows? Pin (39) of IC3201: About +8V Pins (65) and (66) of IC3201: About +5V Pins (11), (12) and (13) of IC3201: About +3.3V Yes Is the voltage at pin (5) (standby control terminal) of IC3301 as specified (about +2V)? Yes Is the voltage at pin (7) (power input terminal) of IC3301 as specified (about +12.5V)? Yes Check the following points: 1 Monitor output set at "variable"? 2 Sound volume at minimum? 3 Mute effect on? 4 Headphones connected? Yes Is there the lack of sound in any input mode (TV, video 1/2, component)? No sound from right and left speakers No No No No No No No No Check IC3201 and its peripheral circuits. Check X3201 and its peripheral circuits. Check the lines from pins (29) and (30) of IC2001 to pin (2) of IC3201. Check the following points: +8V Line: check IC3702 and its peripheral circuits as well as the line up to Pin (39) of IC3201. +5V Line: check IC702, Q713 and their peripheral circuits, B5V700MA line, Q3702 and its peripheral circuits, and +5V line of IC3201. +3.3V Line: check IC703, Q712 and their peripheral circuits, B3.3V1.2A line, and +3.3V input line of IC3201. Check the line between pin (56) of IC2001 and pin (5) of IC3301. Check the built-in AC power supply and the line up to pin (7) of IC3301. Do the following and check again: 1 Set the monitor output to "Fixed". 2 Turn up the sound volume. 3 Clear the mute effect. 4 Disconnect the headphones. Check the following points: 1 No TV sound: check Q3201, Q3202 and TU3401, and their peripheral circuits. 2 No Video 1 input sound: check the lines from J3402 to pins (56) and (57) of IC3201. 3 No Video 2 input sound: check the lines from J3403 to pins (53) and (54) of IC3201. 4 No Component input sound: check the lines from J3404 to pins (50) and (51) of IC3201. No Audio Output Check the lines from between pins (36) (Rch) and (37) (Lch) of IC3201 to pins (2) (Rch) and (4) (Lch) of J3403. Yes Is the collector signal of Q3403 at "L"? Yes Are the audio signal outputs at pins (36) (Rch) and (37) (Lch) of IC3201? Yes Check the following points: 1 Sound heard from speakers? 2 Monitor output properly connected? 3 Mute effect on? No sound from monitor output No No No Check the line from pin (58) of IC2001 to Q3403, as well as Q3401 and Q3402. Check IC3201 and Its peripheral circuits. Do the following and check again: 1 Go to "No sound from speakers". 2 Reconnect the monitor output properly. 3 Clear the mute effect. LC-15S4U-S TROUBLE SHOOTING TABLE (Continued) No TV Color Check the output of IC801 and its peripheral circuits. No S Video Color Check the line between pin (6) of J3401 and pin (24) of IC2001 as well as the line between pin (49) of IC2001 and pin (2) of IC3406. Make sure the microprocessor's adjustment process menu settings are as specified. No Video Color No Color Check the Cb and Cr lines of SC2001 and its peripheral circuits. No Are the Inputs at pins (21) and (33) of IC801 as specified? No Component Color LC-15S4U-S TROUBLE SHOOTING TABLE (Continued) 31 LC-15S4U-S MAJOR IC INFORMATIONS 1-1. Description of Pins of IC2001 (RH-iXA631WJN1Q or RH-iXA631WJZZQ) Pin No. Pin Name I/O Pin Name Function 1 P96 O N.C 2 P95 O N.C 3 P94 O N.C 4 P93 O N.C 5 P92 O 6 TB1in I CSYNC Composite sync signal 7 TB0in I IREM1 Remote control signal 8 BYTE I BYTE Connected to GND N.C 9 CNVss I CNVss Connected to GND (connected to Vcc1 for CNVSS at flash write) 10 Xc in I Xc in 32-kHz quartz oscillator (for clock count) 11 Xc out O Xc out 32-kHz quartz oscillator (for clock count) 12 RESET I RESET Microprocessor reset at "L" 13 X out O X out System clock output 14 Vss I Vss GND 15 X in I X in System clock input 16 Vcc1 I Vcc1 VDD (+3.3V) 17 NMI I NMI 18 P84 O 19 INT1 I P SW in Main power monitor 20 INT0 I VSYNC VSYNC signal input 21 P81 O 22 P82 O AC_Ctrl AC adaptor power consumption control 23 P77 O DAC1CS Gradation control IC chip select 24 P76 I SSW Connected to S terminal at "L" 25 P75 O 26 P74 O 27 P73 I/O SDA2 Serial data line 2 for I2C bus 2 system 28 P72 I/O SCL2 Serial clock line 2 for I2C bus 2 system (EEPROM) 29 P71 I/O SCL1 Serial clock line 1 for I2C bus 2 system (others) 30 P70 I/O SDA1 Serial data line 1 for I2C bus 2 system 31 P67 O TxD (TxD at flash write) 32 P66 O RxD (RxD at flash write) 33 P65 O SCLK (Clock input at flash write) 34 P64 O BUSY (Busy output at flash write) 35 TxD0 O MPWEL Data signal input for DVP 4-line serial (MPWEL) 36 RxD0 I MPOE Data output signal for DVP 4-line serial (MPOE) 37 CLK0 O MPWEH 38 P60 O (Connected to Vcc1 for NMI at flash write) N.C N.C N.C N.C Clock for DVP 4-line serial (MPWEH) N.C 39 P57 O 40 P56 O 41 P55 I 42 P54 I(O) 43 P53 O S IN/OUT Audio input/output select 44 P52 O COMP AV selector switch 45 P51 O TIMER(RLED) On timer LED control (power RLED control) 46 P50 I MRDY(CE) I2C bus open connection detect (connected to Vcc2 for CE at flash write) LED POW(GLED) 47 P47 O 48 P46 O MAIN SW LED power control N.C POW in(EPM) DC/DC start detect (connected to Vss for EPM at flash write) L_ERR Fluorescent lamp error detect Power GLED control N.C 49 P45 O S_SEL AV selector switch 50 P44 O VSH OUT Panel gate driver voltage control 32 LC-15S4U-S Pin No. Pin Name I/O Pin Name Function 51 P43 O N.C 52 P42 O HP_MUTE Headphones mute SP_MUTE1 Main speaker mute 53 P41 O 54 P40 O 55 P37 I HP DET Headphones detect 56 P36 O SSTBY Amplifier power control 57 P35 I VSH_IN Panel gate driver voltage confirm 58 P34 O L MUTE Line out audio mute 59 P33 O V_IN/OUT Video input/output select 60 P32 O SRESET Audio IC reset output 61 P31 O 62 Xcc2 I Vcc2 63 P30 O TCON_OUT_OTL DVP control output control 64 Vss I Vss 65 P27 O V_SEL AV selector switch 66 P26 O TV_SEL AV selector switch 67 P25 O BUS_SELECT_H(I2C) DVP I2C/4-line communication system select (H: I2C control, L: Serial control) 68 P24 O MPCE N.C N.C Power input GND DVP 4-line serial chip enable (MPCE)/DVP slave address select 69 P23 O OPC_LED OPC LED light-up 70 P22 O INV_POW Separately-excited inverter power control 71 P21 O VGH Panel power control 72 P20 O POW out DC/DC control output 73 P17 I ADP POW Adaptor ON/OFF input 74 P16 O DAC_OUTCON Gradation control IC output control 75 P15 O N.C 76 P14 O N.C 77 P13 O 78 P12 O MP_DA 79 P11 O MP_CLK Temperature sensor or gradation control IC clock output 80 P10 O DDC_RESET Video IC reset output (Renesas DVP, 3D YC) 81 P07 I KEY4 Key input 4 82 P06 I KEY5 83 P05 O N.C 84 P04 O N.C N.C Gradation control IC data output Key input 5 85 P03 I MODEL Model ID port 86 P02 I SHORT_DET Over-current protection detect 87 P01 I INCH2 Screen size ID port 2 88 P00 I INCH1 Screen size ID port 1 89 AN7 I AFT 90 P106 O 91 AN5 I KEY1 Key input 1 92 AN4 I KEY2 Key input 2 93 P103 O 94 AN2 I 95 P101 O 96 AVss I 97 P100 O 98 VREF I VREF Connected to +3.3V 99 AVcc I AVcc Connected to +3.3V 100 P97 O AFT voltage input N.C N.C OPC_IN OPC sensor level input N.C AVss Connected to GND N.C N.C 33 LC-15S4U-S BLOCK DIAGRAM LED_PWB H LCD_Panel AUDIO_POWER_AMP HP (Front) Jack 35ø (STEREO) SOUND_PROCESSOR IC3201 IC3301 TUNER_PWB DACM_OUT SLEEP (S_STBY) LCD PANEL RED,GREEN,BLUE DACA_OUT SP_MUTE SP MAIN_PWB CK, SP CVBS1-in 40 ANA_IN1 SIF AMP SP x2 Y-in 42 ANA_IN2 QS SC1_IN G T-CON I2C (33V) C-in 31 SCL/SDA SC2_IN VIDEO /PANEL PROCESSOR SC2_OUT SC3_IN DVP-ML D-Y-in 44 SC4_IN VGA IC801 SC1_OUT Pb-in 33 Pr-in 21 OFL AUDIO IN/OUT SWITCH IC3401 OUT IN F H OUT IN/OUT V OUT SIN/OUT AFT GRADATION IC IC1101 to MPU VIDEO TUNER S-IF VSYNC I2C (3.3V) E MPWEH, MPWEL, MPOE, MPCE, TSTCLK CSYNC MPCLK ,MPRDA, MPRCS S-SW SY-IN INPUT 1 IN S- DET SC-IN DC IN DET IC2010 AUDIO-IN VIDEO-IN BUFFER AUDIO-IN/OUT MPU IC2001 LERR E2PROM IC2009 RESET KEY BUFFER OPC RC OPC R/C RECEIVER RESET IC2006 VIDEO-IN/OUT D INPUT3 IN/OUT IC3402 V_SEL TV_SEL CONTROL KEY BUFFER OUT OFL1 LED_UNIT IN/OUT C INPUT 1 COMPONENT Y-IN V_IN/OUT DC/AC INVERTER BUFFER Pb-IN LAMP ERROR DET IN VIDEO IN/OUT SWITCH Q3410 AUDIO-IN BUFFER LAMP L-TYPE X4 Pr-IN BUFFER SOUND VCC TUNER_PWB F3702 2.0A F6501 1.6A 5.3V IC2003 +3.3V IC2011 F6502 1.6A +35V AC ADAPTER B SIG VCC 12V DC IN F3701 2.5A T701 CONTRO L IC701,Q716 T701 DC/D C CONVERTER +9V +5.3V MAIN_PWB -7V -12V +5V IC702 AC IN INVERTER VCC A 1 +1.8V IC802 +3.3V IC703 2 3 34 4 5 6 7 8 9 10 11 35 12 LC-15S4U-S OVERALL WIRING DIAGRAM H G F E D C B A 1 2 3 36 4 5 6 7 8 9 10 11 37 12 LC-15S4U-S DESCRIPTION OF SCHEMATIC DIAGRAM VOLTAGE MEASUREMENT CONDITION: 1. The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 110-240V. Signals are fed by a color bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. INDICATION OF RESISTOR & CAPACITOR: RESISTOR 1. The unit of resistance “Ω” is omitted. (K=kΩ=1000 Ω, M=MΩ). 2. All resistors are ± 5%, unless otherwise noted. (K= ± 10%, F= ± 1%, D= ± 0.5%) 3. All resistors are 1/16W, unless otherwise noted. CAPACITOR 1. All capacitors are µF, unless otherwise noted. (P=pF=µµF). 2. All capacitors are 50V, unless otherwise noted. CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours. SAFETY NOTES: 1.DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS. 2.SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING. IMPORTANT SAFETY NOTICE: PARTS MARKED WITH “å” ( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET. AVIS DE SECURITE IMPORTANT: LES PIECES MARQUEES “å” ( )SONT IMPORTANTES POUR MAINTENIR LA SECURITE DE L'APPAREIL. NE REMPLACER CES PIEDES QUE PAR DES PIECES DONT LE NUMERO EST SPECIFIE POUR MAINTENIR LA SECURITE ET PROTEGER LE BON FONCTIONNEMENT DE L'APPAREIL. 38 LC-15S4U-S SCHEMATIC DIAGRAM Ë R/C, LED Unit H G F E D C B A 1 2 3 4 39 5 6 LC-15S4U-S ËMAIN Unit-1/5 H G F E D C B A 1 2 3 40 4 5 6 7 8 9 10 11 41 12 LC-15S4U-S ËMAIN Unit-2/5 H G F E D C B A 1 2 3 42 4 5 6 7 8 9 10 11 43 12 LC-15S4U-S ËMAIN Unit-3/5 H G F E D C B A 1 2 3 44 4 5 6 7 8 9 10 11 45 12 LC-15S4U-S ËMAIN Unit-4/5 H G F E D C B A 1 2 3 46 4 5 6 7 8 9 10 11 47 12 LC-15S4U-S ËMAIN Unit-5/5 H G F E D C B A 1 2 3 48 4 5 6 7 8 9 10 11 49 12 LC-15S4U-S ËANALOG Unit-1/5 H G F E D C B A 1 2 3 50 4 5 6 7 8 9 10 11 51 12 LC-15S4U-S ËANALOG Unit-2/5 H G F E D C B A 1 2 3 52 4 5 6 7 8 9 10 11 53 12 LC-15S4U-S ËANALOG Unit-3/5 H G F E D C B A 1 2 3 54 4 5 6 7 8 9 10 11 55 12 LC-15S4U-S ËANALOG Unit-4/5 H G F E D C B A 1 2 3 56 4 5 6 7 8 9 10 11 57 12 LC-15S4U-S ËANALOG Unit-5/5 H G F E D C B A 1 2 3 58 4 5 6 7 8 9 10 11 59 12 LC-15S4U-S PRINTED WIRING BOARD ASSEMBLIES H G F E D C B MAIN Unit (Side-A) A 1 2 3 60 4 5 6 7 8 9 10 11 61 12 LC-15S4U-S H C740 FB704 D701 C736 FB711 FB703 R756 C742 R755 T701 FB709 L702 C744 C746 FB706 D705 C886 D706 D709 R2030 D708 R2026 D707 R2032 R2044 FB701 D703 R2033 R2046 R2078 R2049 C737 FB710 FB707 C747 C748 C745 FB708 C872 R2048 R2050 R2053 R2054 R876 R2057 C750 R2038 P2002 LUG2002 C739 D702 Q713 R2017 C2012 R2061 R2060 R833 C735 R2018 C749 C832 IC2001 R2063 R2062 C Q716 C2019 C2018 R2073 C2010 R2077 R2015 C831 R877 C829 C821 C822 C823 C814 C815 C816 C828 R830 C802 C803 C804 C805 C808 C809 C810 C877 R829 C743 Q715 R2008 R2010 R2065 R2064 C830 C801 R2042 C2016 D704 C2013 R2066 R2059 C885 D C859 R2045 C2017 C1106 C834 C833 C857 FL2001 R757 C2014 R2083 C856 L801 R2082 R811 C865 C866 C858 IC2011 C2006 R2056 X2001 R2072 C835 IC801 R809 R810 D2007 R2058 R808 R883 L706 Q1705 C2008 C1104 R882 C855 SC1202 C1105 C839 C840 C841 C842 C843 C844 C837 C836 R812 E C874 C838 C852 C853 C854 X801 R899 R869 C851 C850 C846 C845 C848 C847 IC1101 L701 R2021 C2005 C2009 C849 R1701 L1703 R1202 FB705 R1204 C2004 R1206 C741 C1102 L1701 Q712 C1107 D1701 C1711 R1201 FB702 R2027 FDC1 R1203 L703 C1702 C1714 R2031 F R860 R861 R1205 C1713 LUG2053 C1710 C1712 C1110 R1722 SC1203 SC1201 C738 G K001 SC701 MASK001 SC2001 B MAIN Unit (Chip Parts Side-A) A 1 2 3 62 4 5 6 7 8 9 10 11 63 12 LC-15S4U-S H G F E D C B MAIN Unit (Side-B) A 1 2 3 64 4 5 6 7 8 9 10 11 65 12 LC-15S4U-S H D1702 G R1112 C1112 R1113 TL1233 TL1237 FDC2 R868 R867 C875 R855 R1120 D1103 R1104 R1209 FB801 R1208 C1101 R1105 C1109 R1207 R1117 R1115 D1102 R1116 R1111 Q1104 Q1103 C876 R1103 D1104 R1101 C1103 TL1286 R881 R892 R898 C869 R807 C868 Q801 R805 C871 IC804 R804 R890 R889 C870 TL1252 TL1256 R1213 TL1258 C806 C807 C811 C812 C818 C820 TL802 FB807 C878 TL1257 TL1259 TL1260 TL1280 TL1284 TL1281 IC802 R878 C864 R817 R818 R822 R826 C817 R819 R821 C819 R820 C824 R823 R879 R880 TL2085 C826 R824 R827 C827 R825 R2034 TL2080 TL2005 R1212 R816 C863 C813 L802 C862 C825 R814 D801 Q2022 Q2021 R874 R828 R2002 TL1240 TL1255 R813 R831 R2003 TL1253 TL1254 R1211 R888 FB804 R801 R802 R873 Q2012 R2051 R2081 IC2010 R2005 TL2084 Q2005 TL1241 R806 R815 R895 Q803 R893 R896 R894 R2068 C860 R884 R832 FB803 R803 R1210 R885 R897 Q802 Q2019 IC2009 Q2023 R2067 R891 C867 IC803 FB806 R2043 R886 C861 C879 FB805 C880 R843 TL801 C881 R2079 R2080 R2074 R2039 C883 C884 R887 R2069 C2021 C887 TL2075 Q2020 R2070 C2022 TL2076 C882 R2071 R2076 R2088 R2020 R2019 R704 R2016 C2007 R2028 R2040 R721 R2022 R2029 C2011 R724 C705 R2036 C720 R2013 R2025 C717 R2085 R2052 R2009 R2037 R2014 R2023 R728 R2075 R2047 C2023 R2035 R735 R2024 C715 C2015 R716 IC2006 R719 Q702 R711 TL2074 TL2073 R731 C713 R718 R702 C707 R706 R2086 R738 IC705 R710 C2002 C2001 C708 C710 C703 C719 R707 R730 C R723 C730 R2004 R2087 C732 R742 R734 R714 TL2072 R750 C726 R749 R744 R748 C2020 R2011 D2002 R2055 C701 D2008 R2012 Q701 C712 TL1276 TL1203 TL1208 TL1213 TL1218 TL1223 TL1228 TL1239 TL1245 TL1249 TL1278 TL1201 TL1205 TL1210 TL1215 TL1220 TL1225 TL1230 TL1243 TL1247 TL1251 TL2071 TL2070 TL1236 TL1282 TL2001 Q708 Q710 Q709 Q711 R739 R753 C723 R1114 C702 C711 R743 R745 D1105 C704 IC2003 C722 R732 R2084 TL1277 TL1202 TL1207 TL1212 TL1217 TL1222 TL1227 TL1238 TL1244 TL1248 TL1283 TL1275 TL1204 TL1209 TL1214 TL1219 TL1224 TL1229 TL1242 TL1246 TL1250 R1119 R1102 C2003 R2041 IC701 R1106 R766 C716 R1118 C1108 R1718 R715 R703 R708 TL1263 TL1267 TL1271 C1201 TL1261 TL1265 TL1269 TL1273 R1121 R2006 R2007 C731 R1109 R1110 D1101 R701 C724 R1108 R729 E D R1725 R1726 Q1709 C1113 R736 R726 R720 R754 C1111 Q1102 R1715 D1704 R1717 R1716 Q1706 Q1101 Q1707 C1707 C1705 R1714 R1719 Q1708 C1706 R1708 D1705 R1107 C1114 R1723 IC1701 IC703 R1707 R1713 R709 R752 C733 R740 C1704 C728 R751 R741 R762 D710 Q705 Q722 R760 Q724 R763 Q1704 C727 C725 R764 D1703 R1720 R1709 C729 R761 R1706 C734 R1705 R1724 R747 C709 C1708 R712 IC702 R737 R758 Q723 F R713 R727 Q1703 R1704 R717 R759 R746 C718 R765 C721 TL1285 TL1264 TL1268 TL1272 TL1279 TL1206 TL1262 TL1266 TL1270 TL1274 TL1287 C1703 R722 R725 R733 Q706 C706 C714 R705 TL708 TL709 TL701 TL702 TL704 TL718 TL714 TL711 TL712 TL710 TL715 TL2032 TL2026 TL2018 TL2013 TL2064 TL2007 TL2036 TL2029 TL2022 TL2065 TL2009 TL2067 TL2011 TL2034 TL2031 TL2024 TL2020 TL2015 TL2008 TL2061 TL2017 TL2012 TL2042 TL2037TL2033 TL2025 TL2021 TL2016 TL2069 TL2063 TL2035 TL2023 TL2066 TL2010 TL2062 TL2040 TL2019 TL2014 TL2068 TL2027 TL2006 TL2004 TL2039 C754 C756 TL705 TL706 TL716 TL717 TL713 TL2003 TL2081 TL2002 TL2028 MASK002 C752 C753 C755 C757 C751 TL2077 TL2030 B MAIN Unit (Chip Parts Side-B) A 1 2 3 66 4 5 6 7 8 9 10 11 67 12 LC-15S4U-S H G F E D C B A ANALOG Unit (Component Side) 1 2 3 68 4 5 6 7 8 9 10 11 69 12 LC-15S4U-S F3701 LUG3404 J3701 R3701 H R3731 R3723 P3703 C3713 R3719 R3411 C3406 C3712 R3408 C3407 C3711 J3404 D3709 D3708 R3721 R3722 D3701 R3724 Q3707 Q3708 C3710 C3307 R3733 D3706 D3707 F3702 G R3720 D3403 D3404 C3499 R3539 C3498 C3412 R3461 C3495 Q3413 R3484 R3486 R3468 J3405 C3703 C3702 C3444 R3488 Q3415 R3489 C3446 C3497 R3420 R3538 C3456 C3451 D3412 R3421 L3406 R3477 R3482 D3411 C3416 R3439 C3448 R3443 C3450 C3455 R3485 R3487 C3460 R3483 R3481 R3454 Q3414 C3426 Q3405 L3408 R3422 R3458 C3415 D3409 R3459 R3425 C3501 D3410 C3414 C3496 Q3705 R3544 R3709 Q3702 R3705 C3715 Q3706 R3713 C3704 D3710 C3708R3729 C3707R3725 R3708 R3711 C3705 R3710 R3730 C3502 R3541 IC3402 C3425 C3422 C3423 R3542 R3492 R3452 Q3407 C3420 R3543 R3444 Q3410 R3467 Q3416 R3429 IC3401 R3453R3466 Q3406 R3434 R3432 R3465 R3449 C3428 Q3401 C3409 Q3403 R3446 R3438 R3424 R3427 D3415 R3419 Q3402 C3411 R3448 R3405 R3412 J3403 Q3704 D3705 R3717 R3716 R3714 R3715 IC3701 C3706 R3712 C3709 D3401 E IC3702 R3726 R3718 C3714 D3402 R3728 R3727 cam1 D3704 R3707 R3704 R3706 C3701 P3702 D3703Q3703 F D3702 R3734 Q3709 R3735 R3445 R3440 C3413 R3455 Q3408 R3451 R3456 R3450 LUG3403 L3407 R3540C3500 Q3409 R3462 R3428 R3426 C3457 C3427 TU3402 C3410 R3403 R3406R3418 P3402 R3476 F6501 L3404 D P3401 F6502 R3216 C3244 R3491 J3402 R3201 R3222 L3201 L3202 R3471 R3404 R3460 R3415 R3473 C3441 C3403 R3401 Q3412 C3443 R3416 R3472 R3402 D3408 D3407 SW4052 SW4053 LUG3401 R4052 SW4054 D4051 SW4051 J3401 R4055 SW4050 D4050 SW4055 R4051 SW4056 R4050 D4052 P6500 R4053 R4054 Q3411 R3470 C3228 C3231 R3475 Q3201 L3203 R3206 R3208 C3223 R3221R3207R3209 X3201 FB3201 C3230 R3407 D3414 D3413 R3423 D3406 D3405 R3474 C3245 Q6501 C3233 C3232 C3229 C3222 C3227 D3202 C3214 P6501 T6500 D3203 Q3202 C3248 C3215 C6510 C3318 IC3201 C3212 C3211 C3216 C3218 C3316 C3236 R3211 C3235 C3219 C3319 Q3304 R3310 C3320 R3312 R3315 D3301 R3306 R3210 C3224 Q3302 C3246 C3247 R3316 R3313 R3307 R3314 D3302 C3317 R3309 R3308 D6500 Q6502 R6521 C3301 Q6500 B R3410 C3405 C3226 R3311 R6520 C6503 R6502 R6500 R6503 R6508 R6509 Q6506 R6510 C6502 R6501 R6512 R6511 C6505 X3202 Q3301 R3413 C3408 C3225 R6517 Q6504 C3217 T6502 C6504 C3202 C3203 R3301 C6511 C3308 L6500 C3204 IC3202 Q6503 C C3239 C3238 C3237 R3212 R3205 C3206 L6503 R3204 R3214 R3203 R3213 C3241 C3242 R3202 C3243 C3309 D3201 C6509 C3305 L6502 IC3301 R6522 R6514 C6507 C3302 C3303 C3310 C3311 R3303 R3302 C3314 C3315 R3304 R3305 C3304 C3313 C3312 C3240 C3210 C3209 R3217 R6516 C6512 C3306 R6515 Q6507 R6523 R6506 C6508 R6504 R6507 LUG3402 R6513 Q6505 R6518 L6504 A ANALOG Unit (Chip Parts Side) 1 2 3 70 4 5 6 7 8 9 10 11 71 12 LC-15S4U-S H G F R/C, LED Unit (Component Side) (QPWBSD413WJZZ) E C4003 R4008 Q4000 R4005 D4001 R4004 C4000 D4000 D4002 J4000 R4007 C R4000 R4001 RMC4000 R4006 IC4000 C4001 D4007 D4006 D4005 R4003 R4002 D4004 P4001 Q4001 D Q4002 1 R/C, LED Unit (Chip Parts Side) (QPWBSD413WJZZ) B A 1 2 3 4 72 5 6 LC-15S4U-S Ref. No. Part No. ★ Description Code PARTS LIST Ref. No. ★ Part No. Description LISTE DES PIECES Code PARTS REPLACEMENT CHANGE DES PIECES Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which does no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards. Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep éler élee par la marque å et sont hachur élees dans les listes de pi`eces et dans les diagrammes sch élematiques. La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece recommand élee parl'usine et dans ce manuel de service, peut provoquer une éLelectrocution, un incendie ou toutautre sinistre. "HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. 1. MODEL NUMBER 3. PART NO. in USA: "COMMENT COMMANDER LES PIECES DE RECHANGE" Pour que votre commande soit rapidement et correctement remplie, veuillez fournir les renseignements suivants. 2. REF. NO. 4. DESCRIPTION 1. NUMERO DU MODELE 2. NO. DE REF 3. NO. DE PIECE 4. DESCRIPTION in CANADA: Contact SHARP Electronics of Canada Limited Phone (416) 890-2100 Contact your nearest SHARP Parts Distributor to order. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP ★ MARK: SPARE PARTS-DELIVERY SECTION Ref. No. Part No. ★ Description ★ MARQUE: SECTION LIVRAISON DES PIECES DERECHANGE Code Ref. No. ★ Part No. Description PRINTED WIRING BOARD ASSEMBLYS DUNTKC847FE08 (NOT REPLACEMENT ITEM) MAIN Unit DUNTKC847FE08 – MAIN Unit DUNTKD412WE02 – ANALOG Unit DUNTKD413WE02 – R/C,LED Unit — — — INTEGRATED CIRCUITS IC701 IC702 IC703 IC801 IC802 IC1101 IC1701 IC2001 IC2003 IC2006 IC2009 IC2010 IC2011 RH-iXA828WJZZY RH-iXA828WJZZY RH-iXA828WJZZY RH-iXB150WJZZQ VHiPQ018EH1-1Y VHiBD8120FP-1Y VHiNJM2147M-1Y RH-iXA631WJZZQ VHiSi3010KM-1Y VHiPST3229N1EY VHiBR24L32F-1Y VHiPST3229N1EY VHiPQ1L333M-1Y Q705 Q706 Q709 Q711 Q712 Q713 Q716 Q802 Q803 Q1101 Q1102 Q1103 Q1104 Q1703 Q1704 Q1705 Q1706 Q1707 Q1708 Q2005 Q2019 Q2020 Q2021 Q2022 VSUML2N++++-1Y VSUML2N++++-1Y VSUML1N++++-1Y VSUML2N++++-1Y VSRTQ035P02-1Y VSRTQ035P02-1Y VSRHP020N06-1Y VSFMMT718//-1Y VS2SC3928AR-1Y VSFMMT718//-1Y VSDTC144EE/-1Y VS2SC5566++-1Y VS2SA2013++-1Y VS2SA1036K/-1Y VS2SC3928AR-1Y VSDTC144EE/-1Y VS2SA1037KQ-1Y VSDTC144EE/-1Y VS2SA1037KQ-1Y VSDTC114YE/-1Y VSDTC114EE/-1Y VS2SA1037KQ-1Y VSDTC144EE/-1Y VSDTA144EE/-1Y D701 VHDRB051L40-1Y J J J J J J J J J J J J J BD9300FV-FE2 BD9300FV-FE2 BD9300FV-FE2 R8A66605A02FP PQ018EH01ZPH BD8120FP NJM2147M-TE1 M30622MWP267FP SI-3010KM-TL PST3229 BR24L32F-WE2 PST3229 PQ1L333M2SP AH AH AH BG AF AX AF AV AF AD AG AD AD TRANSISTORS LCD PANEL NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY. RLCDTA024WJN1 J 15" LCD Panel Unit Code CN J J J J J J J J J J J J J J J J J J J J J J J J UML2N UML2N UML1N UML2N RTQ035P02 RTQ035P02 RHP020N06 FMMT718 2SC3928AR FMMT718 DTC144EE 2SC5566 2SA2013 2SA1036K 2SC3928AR DTC144EE 2SA1037KQ DTC144EE 2SA1037KQ DTC114YE DTC144EE 2SA1037KQ DTC144EE DTA144EE AC AC AC AC AD AD AD AE AB AE AA AD AD AC AB AA AA AA AA AB AB AA AA AA DIODES 73 J Diode AD LC-15S4U-S Ref. No. ★ Part No. Description Code Ref. No. DUNTKC847FE08 C807 C808 C809 C810 C811 C812 C813 C814 C815 C816 C817 C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C828 C829 C830 C831 C832 C833 C834 C835 C836 C837 C838 C839 C840 C841 C842 C843 C844 C845 C846 C847 C848 C849 C850 C851 C852 C853 C854 C855 C856 C857 C858 C859 C860 C861 C862 C863 C864 C865 C866 C867 C872 C874 C875 C876 C877 C878 C886 C887 C1101 C1102 C1103 C1105 C1106 C1107 MAIN Unit (Continued) D702 D704 D705 D706 D707 D708 D709 D801 D1101 D1105 D1701 D1702 D1703 D1704 D1705 D2002 D2007 VHDRB051L40-1Y VHDSFPB56//2EY VHDRB160M30-1Y VHDRF071M2S-1Y VHDRB160M30-1Y VHDRB160M40-1Y VHD1SS355//-1Y VHDDAN222//-1Y VHDDAN202K/-1Y VHD1SS250//1EY VHDDAN222//-1Y VHDDAN222//-1Y VHD1SS250//1EY VHDRB521S30-1Y VHDDAN222//-1Y VHDDAN202K/-1Y VHDRB491D++-1Y J J J J J J J J J J J J J J J J J Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode AD AC AC AD AC AC AB AA AB AB AA AA AB AC AA AB AD PACKAGED CIRCUITS X801 RCRSCA097WJZZY J Crystal, 54MHz X2001 RCRSC0032TAZZY J Crystal, 32.768kHz AG AG FILTER AND COILS FL2001 L701 L703 L802 L1701 L1703 RFiLZA003WJPZY RCiLPA154WJZZY RCiLPA154WJZZY VPCNN220J2R9NY VPCNN470J5R4NY RCiLPA143WJZZY J J J J J J Filter, 16MHz Coil Coil Peaking 22µH Peaking 47µH Coil T701 RTRNWA156WJZZY J Transformer C703 C704 C706 C707 C710 C711 C714 C715 C719 C721 C722 C723 C724 C725 C727 C728 C729 C731 C733 C734 C735 C736 C738 C739 C741 C742 C744 C745 C747 C749 C750 C801 C802 C803 C804 C805 C806 VCKYCY1EF104ZY VCKYCY1EB333KY VCKYCY1EB333KY VCKYCY1EB333KY VCKYCY1HB332KY VCCCCY1HH102JY VCCCCY1HH331JY VCCCCY1HH330JY VCCCCY1HH151JY VCCCCY1HH101JY VCCCCY1HH101JY VCCCCY1HH181JY VCKYTV1CB105KY VCKYCY1EB123KY VCKYCY1EB123KY RC-KZA109WJZZY RC-KZA109WJZZY VCCCCY1HH102JY VCCCCY1HH102JY VCCCCY1HH102JY RC-KZA101WJZZY RC-KZA101WJZZY RC-KZA108WJZZY RC-KZA108WJZZY VCKYCY1HB562KY VCEASX1CN106MY RC-KZA215WJZZY RC-KZA109WJZZY RC-KZA109WJZZY RC-KZA109WJZZY RC-KZA109WJZZY VCKYCZ1AB333KY VCKYCZ1AB333KY VCKYCZ1AB104KY VCKYCZ1AB104KY VCKYCZ1AB104KY VCKYCY1CB104KY AD AE AE AB AB AD TRANSFORMER AG CAPACITORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.1 0.033 0.033 0.033 3300p 1000p 330p 33p 150p 100p 100p 180p 1 0.012 0.012 10 10 1000p 1000p 1000p 10 10 10 10 5600p 10 1 10 10 10 10 0.033 0.033 0.1 0.1 0.1 0.1 25V 25V 25V 25V 50V 50V 50V 50V 50V 50V 50V 50V 16V 25V 25V 16V 16V 50V 50V 50V 6.3V 6.3V 10V 10V 50V 16V 50V 16V 16V 16V 16V 10V 10V 10V 10V 10V 16V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic AA AA AA AA AA AB AA AA AA AA AA AA AC AA AA AC AC AB AB AB AC AC AC AC AA AC AC AC AC AC AC AB AB AB AB AB AB 74 Part No. ★ VCKYCY1CB104KY J VCKYCZ1AB104KY J VCKYCZ1AB104KY J VCKYCZ1AB104KY J VCKYCY1CB104KY J VCKYCY1CB104KY J VCKYCY1EB333KY J VCKYCZ1AB104KY J VCKYCZ1AB104KY J VCKYCZ1AB104KY J VCKYCY1HB104KY J VCKYCY1CB104KY J VCKYCY1HB104KY J VCKYCY1CB104KY J VCKYCZ1AB104KY J VCKYCZ1AB104KY J VCKYCZ1AB104KY J VCKYCY1HB104KY J VCKYCY1CB104KY J VCKYCY1HB104KY J VCKYCY1HB104KY J VCKYCZ1AB104KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB104KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB104KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB104KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB104KY J VCKYCZ1AB333KY J VCKYCZ1AB333KY J VCKYCZ1AB104KY J VCKYCZ1AB333KY J RC-KZA101WJZZY J RC-KZA101WJZZY J RC-KZA101WJZZY J VCKYCY1HB104KY J VCKYCY1HB104KY J VCCCCY1HH5R0CY J VCCCCY1HH5R0CY J RC-KZA101WJZZY J VCEASX0JN227MY J VCKYCZ1AB104KY J VCKYCY1HB103KY J VCKYCY1HB102KY J VCEASX0JN476MY J VCKYCY1AF105ZY J VCEASY1CN477MY J VCKYCY1HB103KY J RC-KZA108WJZZY J VCAAPD0JJ476MY J RC-KZA101WJZZY J VCKYCY1EF104ZY J RC-KZA108WJZZY J VCCCCY1HH560JY J Description 0.1 0.1 0.1 0.1 0.1 0.1 0.033 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.033 0.033 0.033 0.1 0.033 0.033 0.1 0.033 0.033 0.033 0.033 0.033 0.033 0.033 0.033 0.033 0.033 0.033 0.033 0.033 0.033 0.033 0.1 0.033 0.033 0.033 0.1 0.033 0.033 0.1 0.033 10 10 10 0.1 0.1 5p 5p 10 220 0.1 0.01 1000p 47 1 470 0.01 10 47 10 0.1 10 56p 16V 10V 10V 10V 16V 16V 25V 10V 10V 10V 50V 16V 50V 16V 10V 10V 10V 50V 16V 50V 50V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 10V 6.3V 6.3V 6.3V 50V 50V 50V 50V 6.3V 6.3V 10V 50V 50V 6.3V 10V 16V 50V 10V 6.3V 6.3V 25V 10V 50V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Code AB AB AB AB AB AB AA AB AB AB AA AB AA AB AB AB AB AA AB AA AA AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AC AC AC AA AA AA AA AC AC AB AA AA AC AC AD AA AC AE AC AA AC AB LC-15S4U-S Ref. No. ★ Part No. Description Code Ref. No. DUNTKC847FE08 R752 R754 R755 R756 R757 R759 R760 R765 R766 R801 R808 R809 R810 R811 R812 R813 R814 R815 R816 R817 R819 R820 R823 R824 R825 R826 R831 R832 R843 R855 R860 R861 R867 R868 R869 R873 R874 R876 R878 R879 R880 R882 R883 R893 R894 R895 R896 R1101 R1102 R1104 R1105 R1106 R1107 R1108 R1109 R1110 R1111 R1112 R1113 R1114 R1115 R1117 R1119 R1120 R1201 R1202 R1203 R1204 R1205 R1206 R1207 R1208 R1209 R1210 R1211 MAIN Unit (Continued) C1108 C1109 C1112 C1113 C1114 C1201 C1702 C1703 C1705 C1706 C1707 C1708 C1710 C1711 C1712 C1713 C1714 C2001 C2002 C2004 C2005 C2006 C2008 C2009 C2010 C2012 C2013 C2014 C2015 C2016 C2017 C2018 C2019 C2020 C2021 C2022 RC-KZA108WJZZY VCKYCY1EF104ZY VCKYTV1CB105KY VCKYTV1CB105KY VCKYTV1EB104KY VCKYCY1AB105KY VCKYCY1EF104ZY RC-KZA108WJZZY RC-KZ0071TAZZY VCKYCY1EF104ZY VCKYCY1EF104ZY VCKYTV1HF104ZY VCEASX1HN475MY VCKYCY1HF104ZY VCEASX1HN106MY VCEASY0JN227MY RC-KZA101WJZZY VCKYTV1CF105ZY VCKYCY1EF104ZY VCEASN0JN226MY VCKYCY1EF104ZY VCEASN0JN226MY VCKYCY1EF104ZY VCKYCY1EF104ZY VCKYCY1HB222KY VCKYCY1HB222KY VCKYCY1HB102KY VCKYCY1EF104ZY VCKYTV1CF684ZY VCCCCY1HH100DY VCCCCY1HH120JY RC-KZA101WJZZY VCKYCY1EF104ZY VCKYCY1HB222KY VCKYCY1EF104ZY VCKYCY1EF104ZY R703 R705 R706 R707 R708 R709 R712 R713 R714 R715 R717 R718 R719 R720 R722 R723 R725 R726 R727 R729 R730 R732 R733 R734 R739 R740 R741 R743 R744 R745 R746 R747 R751 VRS-CY1JF333JY VRS-CY1JF333JY VRS-CY1JF104DY VRS-CY1JF104DY VRS-CY1JF104DY VRS-CY1JF104DY VRS-CY1JF104DY VRS-CY1JF104DY VRS-CY1JF333JY VRS-CY1JF223JY VRS-CY1JF223JY VRS-CY1JF223JY VRS-CY1JF104JY VRS-CY1JF223JY VRS-CY1JF223JY VRS-CY1JF123FY VRS-CY1JF333FY VRS-CY1JF203FY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF393FY VRS-CY1JF333FY VRS-CY1JF104FY VRS-CY1JF562JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF101JY VRS-CY1JF331JY VRS-CY1JF511JY VRS-CY1JF511JY VRS-CY1JF511JY VRS-CY1JF511JY J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10 0.1 1 1 0.1 1 0.1 10 2.2 0.1 0.1 0.1 4.7 0.1 10 220 10 1 0.1 22 0.1 22 0.1 0.1 2200p 2200p 1000p 0.1 0.68 10p 12p 10 0.1 2200p 0.1 0.1 10V 25V 16V 16V 25V 10V 25V 10V 6.3V 25V 25V 50V 50V 50V 50V 6.3V 6.3V 16V 25V 6.3V 25V 6.3V 25V 25V 50V 50V 50V 25V 16V 50V 50V 6.3V 25V 50V 25V 25V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic AC AA AC AC AB AB AA AC AD AA AA AB AC AA AC AC AC AB AA AB AA AB AA AA AA AA AA AA AB AA AA AC AA AA AA AA Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 33k 33k 100k 100k 100k 100k 100k 100k 33k 22k 22k 22k 100k 22k 22k 12k 33k 20k 0 0 39k 33k 100k 5.6k 10k 10k 10k 100 330 510 510 510 510 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 75 Part No. VRS-CY1JF511JY VRS-CY1JF303JY VRS-TW2HF272JY VRS-TW2HF272JY VRS-TW2HF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF105JY VRS-CY1JF394JY VRS-CY1JF000JY VRS-TV1JD000JY VRS-CY1JF000JY VRS-CY1JF101JY VRS-CY1JF105JY VRS-CH1JF563JY VRS-CY1JF680JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF750JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF102JY VRS-CY1JF223JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF102JY VRS-CY1JF220JY VRS-CY1JF220JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CH1JF103JY VRS-CY1JF223JY VRS-CJ1JF100JY VRS-CY1JF000JY VRS-CY1JF102JY VRS-CY1JF000JY VRS-CY1JF470JY VRS-CY1JF470JY VRS-TV1JD102JY VRS-CY1JF473JY VRS-CY1JF103JY VRS-CY1JF473JY VRS-CY1JF103JY VRS-CY1JF000JY VRS-CY1JF472FY VRS-CY1JF472FY VRS-CY1JF472JY VRS-TW2ED102JY VRS-TW2HF5R6JY VRS-CY1JF181JY VRS-CY1JF102JY VRS-CY1JF181JY VRS-TW2HF5R6JY VRS-TW2HF101JY VRS-CY1JF103JY VRS-CY1JF000JY VRS-TW2HF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CH1JF470JY VRS-CH1JF470JY VRS-CH1JF470JY VRS-CH1JF470JY VRS-CH1JF470JY VRS-CH1JF470JY VRS-CJ1JF270JY VRS-CY1JF470JY VRS-CY1JF220JY VRS-CY1JF220JY VRS-CY1JF220JY ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 510 30k 2.7k 2.7k 0 0 0 1M 390k 0 0 0 100 1M 56k 68 0 0 75 0 0 0 0 0 0 1k 22k 10k 10k 1k 22 22 10k 10k 10k 10k 22k 10 0 1k 0 47 47 1k 47k 10k 47k 10k 0 4.7k 4.7k 4.7k 1k 5.6 180 1k 180 5.6 100 10k 0 0 0 0 47 47 47 47 47 47 27 47 22 22 22 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/10W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/10W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/4W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/2W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide 1/16W Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA LC-15S4U-S Ref. No. Part No. ★ Description Code DUNTKC847FE08 MAIN Unit (Continued) R1212 R1213 R1701 R1704 R1705 R1706 R1707 R1709 R1713 R1714 R1715 R1716 R1717 R1718 R1719 R1720 R1722 R1723 R1724 R1725 R1726 R2005 R2006 R2007 R2008 R2009 R2010 R2011 R2012 R2013 R2014 R2015 R2016 R2017 R2018 R2019 R2020 R2021 R2022 R2023 R2024 R2026 R2028 R2029 R2030 R2031 R2034 R2035 R2036 R2038 R2039 R2040 R2041 R2043 R2044 R2045 R2046 R2047 R2048 R2050 R2051 R2053 R2054 R2055 R2056 R2058 R2059 R2060 R2063 R2064 R2065 VRS-CY1JF220JY VRS-CY1JF220JY VRS-CY1JF363FY VRS-CY1JF101JY VRS-CY1JF563FY VRS-CY1JF103JY VRS-CY1JF102JY VRS-CY1JF683FY VRS-CY1JF183FY VRS-CY1JF103JY VRS-TV1JD562JY VRS-TW2HF102JY VRS-CY1JF472JY VRS-CY1JF000JY VRS-TW2ED123JY VRS-CY1JF272JY VRS-TW2HF472JY VRS-TW2HF330JY VRS-TW2ED561JY VRS-CY1JF102JY VRS-CY1JF104JY VRS-CY1JF223JY VRS-CY1JF1R0JY VRS-CY1JF103JY VRS-CY1JF102FY VRS-CY1JF102JY VRS-CY1JF623FY VRS-CY1JF433FY VRS-CY1JF103FY VRS-CJ1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF473FY VRS-CJ1JF223JY VRS-CJ1JF102JY VRS-CY1JF823FY VRS-CY1JF124FY VRS-CY1JF274JY VRS-CY1JF393FY VRS-CY1JF184JY VRS-CY1JF823JY VRS-CY1JF103JY VRS-CY1JF124FY VRS-CY1JF473JY VRS-CJ1JF223JY VRS-CY1JF103JY VRS-CY1JF153JY VRS-CY1JF223JY VRS-CY1JF101JY VRS-CH1JF101JY VRS-CY1JF103JY VRS-CY1JF101JY VRS-CY1JF512JY VRS-CY1JF472JY VRS-CJ1JF101JY VRS-CY1JF000JY VRS-CY1JF680JY VRS-CY1JF103JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CJ1JF101JY VRS-CJ1JF682JY VRS-CY1JF104JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 22 22 36k 100 56k 10k 1k 68k 18k 10k 5.6k 1k 4.7k 0 12k 2.7k 4.7k 33 560 1k 100k 22k 1 10k 1k 1k 62k 43k 10k 100 100 100 47k 22k 1k 82k 120k 270k 39k 180k 82k 10k 120k 47k 22k 10k 15k 22k 100 100 10k 100 5.1k 4.7k 100 0 68 10k 100 100 100 100 100 100 100 6.8k 100k 100 100 100 100 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/2W 1/16W 1/16W 1/4W 1/16W 1/2W 1/2W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA Ref. No. Part No. ★ R2066 R2068 R2069 R2070 R2071 R2072 R2073 R2074 R2076 R2078 R2081 R2082 R2085 R2086 R2087 VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF223JY VRS-CJ1JF101JY VRS-CJ1JF153JY VRS-CH1JF680JY VRS-CH1JF101JY VRS-CJ1JF101JY VRS-CY1JF103JY VRS-CJ1JF101JY VRS-CY1JF101JY VRS-CJ1JF101JY VRS-CY1JF101JY VRS-CY1JF103JY VRS-CY1JF103JY J J J J J J J J J J J J J J J Description 100 100 22k 100 15k 68 100 100 10k 100 100 100 100 10k 10k 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA MISCELLANEOUS PARTS FB702 RBLN-0253TAZZY J FB704 RBLN-0209TAZZY J FB705 RBLN-0253TAZZY J FB706 RBLN-0051TAZZY J FB707 RBLN-0253TAZZY J FB708 RBLN-0253TAZZY J FB709 RBLN-0051TAZZY J FB710 RBLN-0253TAZZY J FB711 RBLN-0253TAZZY J FB801 RBLN-0083GEZZY J FB803 RBLN-0006TAZZY J FB805 RBLN-0006TAZZY J FB806 RBLN-0006TAZZY J FB807 RBLN-0210TAZZY J P2002 QPLGNA144WJZZY J SC701 QCNCWA010WJZZYJ SC1201 QSOCNA476WJZZY J SC1202 QSOCNA473WJZZY J SC1203 QSOCNA472WJZZY J SC2001 QSOCNA478WJZZY J LUG2002 QLUGHA006WJZZY J LUG2053 QLUGHA006WJZZY J 76 Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Plug, 20-pin Connector, 15-pin Socket, 50-pin Socket, 30-pin Socket, 20-pin Socket, 60-pin Lug Lug AA AB AA AC AA AA AC AA AA AB AB AB AB AB AF AE AD AE AD AF AC AC LC-15S4U-S Ref. No. ★ Part No. Description Code DUNTKD412WE02 ANALOG Unit Part No. L6502 L6503 L6504 RCiLPA093WJZZ RCiLPA034WJZZ RCiLPA034WJZZ T6500 T6502 RTRNZA083WJZZ RTRNZA083WJZZ C3202 C3203 C3204 C3206 C3209 C3210 C3211 C3212 C3214 C3215 C3216 C3217 C3218 C3223 C3224 C3225 C3226 C3227 C3228 C3229 C3230 C3231 C3232 C3233 C3235 C3236 C3301 C3302 C3303 C3304 C3305 C3306 C3307 C3308 C3309 C3310 C3311 C3312 C3313 C3314 C3315 C3317 C3403 C3405 C3406 C3407 C3408 C3409 C3410 C3411 C3412 C3413 C3414 C3415 C3416 C3420 C3422 C3423 C3425 C3426 C3427 C3428 C3429 C3441 C3443 C3444 VCKYCY1EF104ZY J VCKYCY1AB105KY J VCEASX0JN107MY J VCKYCY1HB102KY J VCKYCY1HB102KY J VCKYCY1HB102KY J VCKYCY1EB223KY J VCKYCY1EB223KY J VCEASX1CN106MY J VCEASX1CN107MY J VCKYCY1EF104ZY J VCEASX1HN335MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCCCCY1HH330JY J VCCCCY1HH330JY J VCKYCY1HB102KY J VCKYCY1EF104ZY J VCEASX1CN106MY J VCKYCY1EF104ZY J VCKYCY1AB105KY J VCEASX0JN107MY J VCCCCY1HH560JY J VCCCCY1HH560JY J VCCCCY1HH5R0CY J VCCCCY1HH5R0CY J VCEASX1CN107MY J VCKYCY1HB102KY J VCKYCY1HB102KY J VCEASX1CN106MY J VCEASX1CN106MY J VCKYTV1CB105KY J RC-EZA216WJZZ J RC-EZA216WJZZ J RC-EZA216WJZZ J VCKYCY1AB105KY J VCKYCY1AB105KY J RC-KZA030WJZZY J RC-KZA030WJZZY J VCKYCY1HB153KY J VCKYCY1HB153KY J RC-KZA030WJZZY J VCKYCY1EF104ZY J VCKYCY1AB105KY J VCKYCY1AB105KY J VCKYCY1AB105KY J VCKYCY1AB105KY J VCEASX1CN106MY J RC-KZA030WJZZY J RC-KZA030WJZZY J RC-KZA067WJZZY J VCCCCY1HH121JY J RC-KZA067WJZZY J VCCCCY1HH121JY J RC-KZA067WJZZY J VCKYCY1EF104ZY J RC-KZA108WJZZY J RC-KZA108WJZZY J VCKYCY1EF104ZY J RC-KZA108WJZZY J RC-KZA108WJZZY J VCKYCY1EF104ZY J VCEASY1CN477MY J RC-KZA108WJZZY J RC-KZA108WJZZY J RC-KZA108WJZZY J å å RH-iXB302WJN1Q VHiLA4635A+-1S VHiTC4053BF1EY VHiNJM2246M-1Y VHiSi3012LU-1Y Q3201 Q3202 Q3301 Q3302 Q3304 Q3401 Q3402 Q3403 Q3405 Q3406 Q3407 Q3408 Q3409 Q3410 Q3411 Q3412 Q3414 Q3416 Q3701 Q3702 Q3703 Q3704 Q3707 Q3708 Q6500 Q6501 Q6502 Q6503 Q6504 Q6505 VS2SC3928AR-1Y VS2SC3928AR-1Y VSDTC314TK/-1Y VSDTC314TK/-1Y VS2SC3928AR-1Y VSDTC314TK/-1Y VSDTC314TK/-1Y VSDTA144EE/-1Y VS2SC3928AR-1Y VSUMG4N++++-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VSDTC314TK/-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VSiMZ1A////-1Y VSUM6K1NTN+-1Y VSDTC114YE/-1Y VSFMMT718//-1Y VS2SA1989R/-1Y VSDTC144EE/-1Y VSUM5K1NTR+-1Y VSUM5K1NTR+-1Y VS2SC5886++-1Y VS2SC5886++-1Y VS2SA1530AR-1Y VS2SC5886++-1Y VS2SC5886++-1Y VS2SA1530AR-1Y D3301 D3302 D3415 D3703 D3704 D3706 D3707 D3708 D3709 D3710 D3711 D4050 D4051 D4052 D6500 VHDDAN222//-1Y RH-EX1397CEZZY VHDDAN222//-1Y VHDDAN222//-1Y VHDRB491D++-1Y VHDiMN10///-1Y VHDiMN10///-1Y VHDDAN222//-1Y VHDDAN222//-1Y RH-EXA095WJZZY RH-EXA095WJZZY RH-EX1271CEZZY RH-EX1283CEZZY RH-EX1271CEZZY VHDDAN222//-1Y J J J J J MSP3445G-QA-S1 LA4635A TC4053BF NJM2246M Si-3012LU 2SC3928AR 2SC3928AR DTC314TK DTC314TK 2SC3928AR DTC314TK DTC314TK DTA144EE 2SC3928AR UMG4N 2SC3928AR 2SC3928AR 2SC3928AR DTC314TK 2SC3928AR 2SC3928AR IMZ1A UM6K1NTN DTC114YE FMMT718 2SA1989R DTC144EE UM5K1NTR UM5K1NTR 2SC5886 2SC5886 2SA1530AR 2SC5886 2SC5886 2SA1530AR AT AM AF AF AE AB AB AC AC AB AC AC AA AB AB AB AB AB AC AB AB AC AC AB AE AB AA AC AC AE AE AB AE AE AB DIODES J J J J J J J J J J J J J J J Diode Zener Diode, 7.5V Diode Diode Diode Diode Diode Diode Diode Zener Diode, 16V Zener Diode, 16V Zener Diode, 12V Zener Diode, 18V Zener Diode, 12V Diode AA AB AA AA AD AB AB AA AA AB AB AB AB AB AA PACKAGED CIRCUITS X3201 RCRSB0250GEZZ J Crystal, 18.432MHz AG COILS L3201 L3202 L3203 L3404 L3406 L6500 VPCNN4R7J1R2NY VPCNN220J2R9NY VPCNN101J7R7NY RCiLPA142WJZZ VPCNN1R0JR50NY RCiLPA093WJZZ J J J J J J Peaking 4.7µH Peaking 22µH Peaking 100µH Coil Peaking 1µH Coil AF AD AD J Transformer J Transformer AN AN CAPACITORS TRANSISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Coil J Coil J Coil Code BB INTEGRATED CIRCUITS IC3201 IC3301 IC3401 IC3402 IC3702 Description TRANSFORMER TUNER NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY. TU3402 VTUVT2U5UF559 J Tuner ★ Ref. No. AB AB AB AD AB AF 77 0.1 1 100 1000p 1000p 1000p 0.022 0.022 10 100 0.1 3.3 0.1 0.1 33p 33p 1000p 0.1 10 0.1 1 100 56p 56p 5p 5p 100 1000p 1000p 10 10 1 1000 1000 1000 1 1 2.2 2.2 0.015 0.015 2.2 0.1 1 1 1 1 10 2.2 2.2 4.7 120p 4.7 120p 4.7 0.1 10 10 0.1 10 10 0.1 470 10 10 10 25V 10V 6.3V 50V 50V 50V 25V 25V 16V 16V 25V 50V 25V 25V 50V 50V 50V 25V 16V 25V 10V 6.3V 50V 50V 50V 50V 16V 50V 50V 16V 16V 16V 16V 16V 16V 10V 10V 10V 10V 50V 50V 10V 25V 10V 10V 10V 10V 16V 10V 10V 10V 50V 10V 50V 10V 25V 10V 10V 25V 10V 10V 25V 16V 10V 10V 10V Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic AA AB AC AA AA AA AA AA AC AC AA AB AA AA AA AA AA AA AC AA AB AC AB AB AA AA AC AA AA AC AC AC AD AD AD AB AB AB AB AA AA AB AA AB AB AB AB AC AB AB AB AA AB AA AB AA AC AC AA AC AC AA AD AC AC AC LC-15S4U-S Ref. No. ★ Part No. Description Code Ref. No. DUNTKD412WE02 R3421 R3422 R3423 R3424 R3425 R3426 R3427 R3428 R3432 R3434 R3439 R3440 R3443 R3444 R3445 R3446 R3448 R3449 R3450 R3451 R3452 R3453 R3454 R3455 R3456 R3458 R3459 R3460 R3461 R3462 R3465 R3466 R3467 R3468 R3470 R3471 R3472 R3473 R3474 R3475 R3481 R3483 R3485 R3487 R3491 R3539 R3540 R3541 R3542 R3543 R3544 R3701 R3705 R3706 R3707 R3718 R3720 R3721 R3722 R3723 R3724 R3725 R3726 R3727 R3728 R3729 R3730 R3731 R3733 R4050 R4051 R4052 R4053 R4054 R4055 ANALOG Unit (Continued) C3446 C3448 C3451 C3455 C3456 C3457 C3495 C3496 C3497 C3502 C3701 C3702 C3709 C3710 C3711 C3712 C3713 C3714 C3715 C6502 C6503 C6504 C6505 C6507 C6508 C6509 C6510 C6511 C6512 RC-KZA108WJZZY RC-KZA108WJZZY VCAAPC0JJ226MY VCKYCY1HF103ZY VCKYCY1EF104ZY RC-EZA560WJZZ VCCCCY1HH101JY VCCCCY1HH101JY VCCCCY1HH151JY VCEASX1CN107MY RC-KZ1025CEZZY RC-KZA108WJZZY RC-EZA559WJZZ RC-KZ0072TAZZY RC-KZ0072TAZZY RC-KZ0072TAZZY RC-KZ0072TAZZY VCEASX1CN476MY RC-KZA111WJZZY VCKYCY1CB473KY VCKYCY1CB473KY RC-EZA468WJZZ VCKYCY1CB333KY VCKYCY1CB473KY VCKYCY1CB473KY RC-EZA468WJZZ RC-FZA107WJZZ RC-FZA107WJZZ VCKYCY1CB473KY R3201 R3205 R3206 R3207 R3208 R3209 R3210 R3211 R3221 R3301 R3302 R3303 R3304 R3305 R3306 R3307 R3308 R3310 R3311 R3312 R3313 R3314 R3315 R3401 R3402 R3403 R3404 R3405 R3406 R3407 R3408 R3410 R3411 R3412 R3413 R3415 R3416 R3418 R3419 R3420 VRS-CJ1JF101JY VRS-CY1JF101JY VRS-CY1JF152JY VRS-CY1JF331JY VRS-CY1JF153JY VRS-CY1JF332JY VRS-CY1JF102JY VRS-CY1JF105JY VRS-CY1JF102JY VRS-CY1JF122JY VRS-CY1JF222JY VRS-CY1JF222JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF123JY VRS-CY1JF392JY VRS-CY1JF392JY VRS-CY1JF183JY VRS-CY1JF822JY VRS-CY1JF103JY VRS-CY1JF000JY VRS-CY1JF101JY VRS-TQ2BD750JY VRS-CY1JF104JY VRS-TQ2BD750JY VRS-CY1JF104JY VRS-CY1JF101JY VRS-TQ2BD750JY VRS-CY1JF104JY VRS-CY1JF104JY VRS-CY1JF104JY VRS-CY1JF101JY VRS-CY1JF104JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF471JY VRS-CY1JF471JY VRS-TQ2BD750JY J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10 10 22 0.01 0.1 3300 100p 100p 150p 100 1 10 0.33F 1 1 1 1 47 1 0.047 0.047 2200 0.033 0.047 0.047 2200 0.1 0.1 0.047 10V 10V 6.3V 50V 25V 6.3V 50V 50V 50V 16V 10V 10V 5.5V 25V 25V 25V 25V 16V 25V 16V 16V 16V 16V 16V 16V 16V 250V 250V 16V Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Film Film Ceramic AC AC AE AA AA AE AA AA AA AC AB AC AF AC AC AC AC AC AC AA AA AE AA AA AA AE AD AD AA Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 100 100 1.5k 330 15k 3.3k 1k 1M 1k 1.2k 2.2k 2.2k 3.3k 3.3k 0 0 12k 3.9k 3.9k 18k 8.2k 10k 0 100 75 100k 75 100k 100 75 100k 100k 100k 100 100k 100 100 470 470 75 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/8W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 78 Part No. VRS-CY1JF101JY VRS-TQ2BD750JY VRS-CY1JF101JY VRS-CY1JF562JY VRS-CY1JF101JY VRS-TQ2BD750JY VRS-CY1JF153JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF104JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF471JY VRS-TQ2BD750JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF100JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-TQ2BD221JY VRS-CY1JF101JY VRS-TQ2BD000JY VRS-CY1JF471JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF104JY VRS-CY1JF471JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CJ1JF331JY VRS-CY1JF123JY VRS-CY1JF123JY VRS-CY1JF223JY VRS-CY1JF223JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF152JY VRS-CY1JF561FY VRS-CY1JF102FY VRS-CJ1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF105JY VRS-CY1JF105JY VRS-CY1JF105JY VRS-TQ2BD100JY VRS-TQ2BD000JY VRS-CY1JF102JY VRS-CY1JF184JY VRS-CY1JF103JY VRS-TQ2BD101JY VRS-CH1JF824JY VRS-CH1JF562JY VRS-CY1JF563JY VRS-TQ2BD000JY VRS-CH1JF222JY VRS-CY1JF682FY VRS-CY1JF152FY VRS-TQ2BD1R0JY VRS-CY1JF102JY VRS-CY1JF132FY VRS-CY1JF102JY VRS-TQ2BD000JY VRS-TQ2BD000JY VRS-CY1JF682JY VRS-CY1JF472JY VRS-CY1JF682JY VRS-CY1JF472JY VRS-CY1JF823JY VRS-CY1JF274JY ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 100 75 100 5.6k 100 75 15k 100 100 100k 10k 10k 470 75 0 10k 10k 10 10k 10k 220 100 0 470 0 10k 10k 100k 470 0 10k 10k 10k 330 12k 12k 22k 22k 1k 1k 1k 1.5k 560 1k 0 0 0 1M 1M 1M 10 0 1k 180k 10k 100 820k 5.6k 56k 0 2.2k 6.8k 1.5k 1 1k 1.3k 1k 0 0 6.8k 4.7k 6.8k 4.7k 82k 270k 1/16W 1/8W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/16W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/8W 1/8W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/8W 1/16W 1/16W 1/16W 1/8W 1/8W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA LC-15S4U-S Ref. No. ★ Part No. Description Code Ref. No. Description DUNTKD412WE02 DUNTKD413WE02 ANALOG Unit (Continued) R/C, LED Unit R6500 R6501 R6502 R6503 R6504 R6506 R6507 R6513 R6520 R6521 R6522 R6523 VRS-TQ2BD362JY VRS-TQ2BD302JY VRS-CY1JF103JY VRS-CY1JF333JY VRS-TQ2BD362JY VRS-CY1JF103JY VRS-CY1JF333JY VRS-TQ2BD302JY VRS-TQ2BD362JY VRS-TQ2BD302JY VRS-TQ2BD302JY VRS-TQ2BD362JY SW4050 SW4051 SW4052 SW4053 SW4054 SW4055 SW4056 QSW-K0065GEZZY QSW-K0065GEZZY QSW-K0065GEZZY QSW-K0065GEZZY QSW-K0065GEZZY QSW-K0065GEZZY QSW-K0065GEZZY J J J J J J J J J J J J 3.6k 3k 10k 33k 3.6k 10k 33k 3k 3.6k 3k 3k 3.6k 1/8W 1/8W 1/16W 1/16W 1/8W 1/16W 1/16W 1/8W 1/8W 1/8W 1/8W 1/8W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide J J J J J J J CH(Channel)(Ù) CH(Channel)(ù) INPUT POWER MENU VOL(Volume)(+) VOL(Volume)(–) IC4000 VHiMM1616++-1Y Fuse, 2.5A/250V Fuse, 2.0A/250V Fuse, 1.6A/250V Fuse, 1.6A/250V Ferrite Bead S-VIDEO AUDIO(L/R)/VIDEO INPUT3/OUTPUT ADUIO(L/R) Y/PB/PR POWER INPUT(DC 12V) Plug, 13-pin Plug, 4-pin Connector, 15-pin Plug, 4-pin Plug, 3-pin Plug, 3-pin Socket, 60-pin Lug Lug Lug Lug Shield, x1 J MM1616XBRE AF TRANSISTORS Q4000 VSDTC144EE/-1Y Q4001 VSDTC144EE/-1Y Q4002 VSDTC144EE/-1Y J DTC144EE J DTC144EE J DTC144EE AA AA AA DIODES D4000 RH-PX0421CEZZY J POWER/WAKE UP TIMER AD Indicator D4001 RH-PX0421CEZZY J OPC Indicator AD D4006 RH-EX1247CEZZY J Zener Diode, 5.6V AB AD AD AD AD AD AD AD CAPACITORS C4000 VCEASX1CN106MY J 10 C4001 VCKYCY1HF103ZY J 0.01 C4003 RC-KZ0117TAZZY J 4.7 16V Electrolytic 50V Ceramic 6.3V Ceramic AC AA AD RESISTORS R4000 R4001 R4002 R4004 R4005 R4006 R4007 R4008 MISCELLANEOUS PARTS F3701 QFS-ZA005WJZZ J F3702 QFS-ZA004WJZZ J F6501 QFS-ZA003WJZZ J F6502 QFS-ZA003WJZZ J FB3201 RBLN-0035TAZZY J J3401 QSOCDA028WJZZ J J3402 QJAKGA071WJZZ X J3403 QJAKGA071WJZZ X J3404 QJAKJ0101SEZZ J J3405 QJAKGA082WJZZ X J3701 QJAKCA010WJZZ J P3401 QPLGN1375TAZZY X P3402 QPLGN0478GEZZ J P3702 QCNCMA012WJZZ J P3703 QPLGN0478GEZZ J P6500 QPLGN0155FJZZY J P6501 QPLGN0155FJZZY J SC3401 QSOCNA478WJZZY J LUG3401 QLUGHA006WJZZY J LUG3402 QLUGHA006WJZZY J LUG3403 QLUGHA006WJZZY J LUG3404 QLUGHA006WJZZY J PSLDMA830WJZZ X Code INTEGRATED CIRCUITS AA AA AA AA AA AA AA AA AA AA AA AA SWITCHES å å å å ★ Part No. AC AD AD AD AB AC VRS-CY1JF331JY VRS-CY1JF182JY VRS-CY1JF331JY VRS-TQ2BD681JY VRS-TQ2BD681JY VRS-CY1JF101JY VRS-TQ2BD681JY VRS-TQ2BD681JY J J J J J J J J 330 1.8k 330 680 680 100 680 680 1/16W 1/16W 1/16W 1/8W 1/8W 1/16W 1/8W 1/8W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AA AA AA AA AA AA AA MISCELLANEOUS PARTS J4000 QJAKJA009WJSA J HEADPHONE Jack P4001 QPLGN1375TAZZY X Plug, 13-pin RMC4000 RRMCUA034WJQZ J R/C Sensor AE AF AB AD AB AE AE AF AC AC AC AC 79 AE AE LC-15S4U-S Ref. No. Part No. ★ Description Code Ref. No. 31 33 CABINET AND MECHANICAL PARTS å 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 CCABAB115WJ01 Not Available HDECQA474WJSA PSPAHA050WJZZ PSPAHA051WJZZ TLABZA459WJZZ TLABZA635WJZZ TLABZA875WJZZ X – J J J J J X Cabinet A Ass’y Cabinet A R/C,LED Cover Mask Spacer(L), x2 Mask Spacer(S), x2 "POP" Label "EnergyStar" Label Material Label 2 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 CCABBA652WJ01 Not Available GCOVAB080WJKA HiNDP5733CESB JBTN-A443WJKA LANGTA162WJFW PMLT-A090WJZZ PSPAH0678CEZZ PSPAHA514WJZZ PSPAHA515WJZZ TLABZA875WJZZ XEBSN30P08000 X – J J J J J J J J X J Cabinet B Ass’y Cabinet B Terminal Cover AQUOS Label Operation Button Reinforcement Angle Light Shielding Spacer, x1 Spacer, x1 Spacer, x2 Spacer, x2 Material Label Screw, x2 3 3-1 3-2 3-3 3-4 CDAi-A238WJ01 GDAi-A238WJSA GLEGGA010WJZZ MHNG-A114WJFW XBBS940P16000 X X J X J Stand Ass’y Stand, Base Cushion Spacer, x6 Tilt Hinge Screw, x4 AC 4 4-1 4-2 4-2-1 4-2-2 4-2-3 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 Not Available RLCDTA024WJN1 Not Available PSLDMA557WJFW PSPAHA333WJZZ TCAUZA031WJZZ KLMP-A099WJZZ PGiDMA015WJZZ PMiR-A059WJZZ PMiR-A060WJZZ PSHEP0283CEZZ PSHEP0307CEZZ PSHEPA268WJZZ PSHEPA277WJZZ PSLDMA273WJZZ PSLDMA284WJZZ – J – J J J J J J J J J J J J J 15" LCD Panel Unit Ass’y 15" LCD Panel Unit Back Shield Ass’y Back Shield Spacer, x2 Caution Label Lamp Unit, x1 Light Guide Panel Reflection Mirror(L), x2 Reflection Mirror(S), x2 Diffusion Sheet, x2 Multi Reflection Sheet, x2 Reflection/deflection Sheet Reflection Sheet Shield, x1 Shield, x1 — CN — AQ AA AB BC BA AE AE AL AC BC AK AG AE 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 GCOVAB082WJKA GCOVAB088WJKA JHNDPA017WJKA LANGTA165WJFW LCHSMA162WJKA LCHSMA242WJKA PSLDMA291WJZZ HiNDPB434WJSA Not Available VSP7530PB678B PSPAKA045WJZZ PSPAKA101WJZZ QCNW-C988WJQZ QCNW-D890WJQZ QCNW-D913WJQZ QCNW-D914WJQZ QCNW-D915WJQZ QCNW-D916WJQZ QEARZA075WJZZ LX-BZ3442CEF9 XBBS930P05000 XBBS940P08000 XBBS940P14000 XBPS730P10JS0 XBPS730P18JS0 XEBS930P14000 J J J J J X J X – J J J J X J J J J J J J J J J J J Stand Cover Bass-Cone Cover Carrying Handle Stand Angle Chassis Frame(R) Chassis Frame(L) Shield, x1 Model Label Serial No. Label Speaker, x2 Spacer, x1 Light Shielding Spacer, x1 Connecting Cord Connecting Cord Connecting Cord Connecting Cord Connecting Cord Connecting Cord Grounding Part, x1 Screw, x4 Screw, x1 Screw, x1 Screw, x4 Screw, x4 Screw, x2 Screw, x5 AK AE AL AG AK — AE AC AC AB AC — AL AD AG AM AD AA AA AC AA AB AF — AL AB AD AF AE AF AG AF AB AB AA AB AB AA AB AA 80 Part No. XEBSN30P08000 XEBS940P16000 ★ Description J Screw, x10 J Screw, x4 Code AA AB LC-15S4U-S CABINET AND MECHANICAL PARTS 14 H 31 C 1 G 8 17 33 31 A 1-3 C 14 G 1-4 1-3 31 F 1-2 1-4 C 1-6 4-2-1 R/C, LED Unit 1-7 E 4-10 1-5 F 4-2-2 4-12 B 4-2-3 C 1-1 4-4 A 4-11 D 4-3 23 4-8 4-2 4-7 E 4 L 31 M 4-9 4-6 B 4-5 11 24 N 4-1 7 D 2-4 H 13 30 15 6 4-6 I 4-5 J 12 2-11 A B 2-2 2-3 2-1 25 C B 20 2-8 2 K Main Unit 2-10 16 29 2-5 22 31 2-6 H 27 26 5 O 21 B I J L M 2-9 28 2-7 3-3 3-1 G 9 K E 3-4 F N D A 19 3 18 O A 3-2 10 1 2 Analog Unit 3 4 81 5 6 LC-15S4U-S Ref. No. Part No. ★ Description Code Ref. No. å X1 X2 X3 X4 X5 X6 X7 X8 LHLDWA002WJSA QACCDA023WJPA QCNWGA074WJPZ RRMCGA293WJSA TCADEA126WJZZ TiNS-B995WJN1 UADP-A086WJPZ Not Available J J X J X X X – Cable Clamp, x1 AC Cord Audio Cable Wireless Remote Control Questionnaire Card Operation Manual AC Adapter "AAA" size Battery, x2 Description (NOT REPLACEMENT ITEM) AD AK S1 S2 S3 S4 S5 AT SPAKCC167WJZZ SPAKPA559WJZZ SPAKXA849WJZZ SSAKA0101GJZZ TLABKA009WJZZ – – – – – Packing Case Wrapping Paper Buffer Material Polyethylene Bag No. Label — SERVICE JIGS (USE FOR SERVICING) QCNW-A555WJZZ QCNW-A556WJZZ QCNW-B784WJZZ J Extension Cable 20-pin (SC1203-LCD) J Extension Cable 50-pin (SC1201-LCD) J Extension Cable 30-pin (SC1202-LCD) AU AU BA Supplied Accessories Wireless remote control X7 "AAA" size batteries (× 2) X8 AC cord AC adapter X4 Code PACKING PARTS SUPPLIED ACCESORIES å ★ Part No. X2 Cable clamp Audio cable X1 X3 Operation manual X6 LC-15S4U 82 — — — — — LC-15S4U-S PACKING OF THE SET S4 X1 X5 X6 X7 X8 X4 X2 X3 S3 S2 S3 S5 S1 83 LC-15S4U-S COPYRIGHT © 2005 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. TQ1937-S Oct. 2005 Printed in Japan Design and Production Information Design : Japan Production : SEMEX MI. KG SHARP CORPORATION AV Systems Group CS Promotion Center Yaita, Tochigi 329-2193, Japan