Download Cleveland OGB-6.20 Operating instructions

Service & Parts Manual
Convotherm Combination Oven-Steamer
MODELS: Gas 10.10 and 6.20
by
OGS-10.10
OGB-10.10
OGS-6.20
OGB-6.20
1333 East 179th St., Cleveland, Ohio, U.S.A. 44110
Enodis
Phone: (216) 481-4900 Fax: (216) 481-3782
Visit our web site at www.clevelandrange.com
0706
Installation
Operating Instructions
Cleaning Instructions
Service Parts
Table of Contents
For the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Instructions for Casters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Specification Sheets OGB-10.10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
OGS-10.10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
OGB-6.20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
OGS-6.20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
Control Panel, Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Control Panel, Detail View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17
Cleaning the Oven Chamber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20
Semi- Automatic Cleaning of Oven Chamber . . . . . . . . . . . . . . . . . . . 21-22
CONVOClean Automatic Cleaning System (optional) . . . . . . . . . . . . 23-24
Descale Steam Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-27
General Assembly Drawings 10.10 Gas Generator with Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29
10.10 Gas Injection with Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-31
6.20 Gas Generator with Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-33
6.20 Gas Injection with Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-35
Component Panel, (OGB 6.20 & 10.10) . . . . . . . . . . . . . . . . . . . . . . . 36-37
Component Panel, (OGS 6.20 & 10.10). . . . . . . . . . . . . . . . . . . . . . . 38-39
Control Panel, with Picto (all models) . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Base, Gas Injector with Cleaning (OGS 10.10) . . . . . . . . . . . . . . . . . . . . 41
Base, Gas Injector, No Cleaning (OGS 10.10) . . . . . . . . . . . . . . . . . . . . . 42
Base, Gas Generator with Cleaning (OGB 6.20) . . . . . . . . . . . . . . . . . . 43
Base, Gas Generator no Cleaning (OGB 6.20) . . . . . . . . . . . . . . . . . . . . 44
Base, Gas Injector with Cleaning (OGS 6.20) . . . . . . . . . . . . . . . . . . . . . 45
Water Hose System, Condenser (all models) . . . . . . . . . . . . . . . . . . . . . . 46
Water Valve (10.10 models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Water Valve (10.10 models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Water Valve, Injector, Gas (OGS 6.20 & 10.10). . . . . . . . . . . . . . . . . . . . 49
Water Supply, Generator W/Cleaning System . . . . . . . . . . . . . . . . . . . . . 50
(OEB & OGB 6.20)
Water Valve (6.20 models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Water Valve (OGS 6.20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Steam Generator, Gas (OGB 6.20) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Service Parts
(continued)
Maintenance
Table of Contents (continued)
Pump, Steam Generator, Gas, 110v (all models) . . . . . . . . . . . . . . . . . . . 54
Burner Insert, Steam Generator Natural Gas (OGB 6.20 & 10.10) . . . . 55
Burner Insert, HL, Premounted (all models) . . . . . . . . . . . . . . . . . . . . . . 56
Burner Insert, Air, LP & Natural Gas (all Gas models) . . . . . . . . . . . . . 57
Door (OES 6.20 & 10.10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Sliding Plate (all models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59-60
Exterior Sheeting (all models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Stand, Closed Base (all models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Assemblies, Stacking Kits
Gas Models (6.20 on 6.20 or 10.20 & 6.10 on 6.10 or 10.10). . . . . . . . . 64
Electric Models (6.10 on 6.10 or 10.10). . . . . . . . . . . . . . . . . . . . . . . . . . 65
OGB 6.20 & 10.10 Sequence of Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66-73
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74-79
Ladder Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80-82
OGS 6.20 & 10.10 Sequence of Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83-88
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89-92
Ladder Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93-94
FOR THE INSTALLER
FOR YOUR SAFETY
Do not store or use gasoline or
other flammable vapors or
liquids in the vicinity of this or
any other appliance.
WARNING
Improper installation, adjustment, alteration, service or
maintenance can cause property damage, injury or death.
Read the installation, operating and maintenance instructions
thoroughly before installing or servicing this equipment.
NOTICE
Post instructions to be followed if the user smells gas.
Display the instructions in a prominent location.
All users of this equipment must understand the instructions.
Obtain the instructions from the local gas supplier.
Failure to follow the instructions if there is a gas leak can
cause death, injury, and/or property damage.
WARNING
Disconnect power at the main external power switch before servicing or repairing a Combi.
Failure to disconnect power can result in death, injury, and property damage.
ALL SERVICE MUST BE PERFORMED BY A QUALIFIED
CLEVELAND RANGE AUTHORIZED TECHNICIAN.
WARNING
Do not connect the Combi Oven-Steamer drain connection to any
drain material that cannot sustain 140o Fahrenheit.
Using drain material that cannot withstand 140o Fahrenheit can
result in injury, equipment damage, and property damage.
This Installation Manual is a part of your new Combi Oven-Steamer. You must keep and maintain it
for the entire life span of your Combi and pass it on to the next owner of the Combi.
KEEP THIS MANUAL FOR REFERENCE
This manual may be subject to new technical developments, modifications, and unforeseen errors.
DO NOT OPERATE OR ATTEMPT TO OPERATE THIS APPLIANCE OR ANY ACCESSORIES WITHOUT READING
COMPLETELY AND FULLY UNDERSTANDING THIS MANUAL
For caster equipped Combis: Per separate instructions, connect the strain relief (restraining
device) and complete any remaining installation procedures BEFORE starting the Combi.
Convotherm by Cleveland Combi Oven-Steamers are intended for other than household use.
1
Cleveland STATEMENT OF POLICIES
LIMITED WARRANTY
CLEVELAND RANGE products are warranted to the original purchaser to be free from defects in materials and workmanship under
normal use and service for the standard warranty period of one year from date of installation or 18 months from date of shipment,
which ever comes first.
CLEVELAND RANGE agrees to repair or replace, at its option, f.o.b. factory, any part which proves to be defective due to defects
in material or workmanship during the warranty period, providing the equipment has been unaltered, and has been PROPERLY
INSTALLED, MAINTAINED, AND OPERATED IN ACCORDANCE WITH THE CLEVELAND RANGE OWNER’S MANUAL.
CLEVELAND RANGE agrees to pay any FACTORY AUTHORIZED EQUIPMENT SERVICE AGENCY (within the continental
United States, and Hawaii) for reasonable labor required to repair or replace, at our option, f.o.b. factory, any part which proves to be
defective due to defects in material or workmanship, during the labor warranty period. This warranty includes travel time not to
exceed two hours and mileage not to exceed 50 miles (100 miles round-trip), BUT DOES NOT INCLUDE POST START-UP,
TIGHTENING LOOSE FITTINGS, MINOR ADJUSTMENTS, MAINTENANCE, CLEANING OR DESCALING.
The standard labor warranty allows factory payment of reasonable labor required to repair or replace such defective parts.
Cleveland Range will not reimburse the expense of labor required for the repair or replacement of parts after the standard warranty
period, unless an Extended Labor Warranty Contract has been purchased to cover the equipment for the balance of the warranty
period from the date of equipment installation, start-up, or demonstration.
PROPER INSTALLATION IS THE RESPONSIBILITY OF THE DEALER, THE OWNER-USER, OR INSTALLING CONTRACTOR,
AND IS NOT COVERED BY THIS WARRANTY. Many local codes exist, and it is the responsibility of the owner and installer to
comply with these codes. Cleveland Range equipment is built to comply with applicable standards for manufacturers, including UL,
ANSI, NSF, ASME/Ntl. Bd., CSA, and others.
BOILER (Steam Generator) MAINTENANCE IS THE RESPONSIBILITY OF THE OWNER-USER AND IS NOT COVERED BY
THIS WARRANTY. The use of good quality feed water is the responsibility of the Owner-User (see Water Quality Recommendations
below). THE USE OF POOR QUALITY FEED WATER WILL VOID EQUIPMENT WARRANTIES. Boiler maintenance supplies,
including boiler hand hole gaskets, are not warranted beyond the first 90 days after the date the equipment is placed into service.
Preventive maintenance records must be available showing descaling per applicable Cleveland Operator Manual for Boiler Proration
Program considerations.
WATER QUALITY RECOMMENDATIONS
TOTAL DISSOLVED SOLIDS
TOTAL ALKALINITY
SILICA
CHLORIDE
pH FACTOR
less than
60 parts per million
less than
20 parts per million
less than
13 parts per million
less than
30 parts per million
greater than 7.5
The foregoing shall constitute the sole and exclusive remedy of original purchaser and the full liability of Cleveland Range for any
breach of warranty. THE FOREGOING IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER WRITTEN,
ORAL, OR IMPLIED, INCLUDING ANY WARRANTY OF PERFORMANCE, MERCHANTABILITY, OR FITNESS FOR PURPOSE,
AND SUPERSEDES AND EXCLUDES ANY ORAL WARRANTIES OR REPRESENTATIONS, OR WRITTEN WARRANTIES OR
REPRESENTATIONS, NOT EXPRESSLY DESIGNATED IN WRITING AS A “WARRANTY” OR “GUARANTEE” OF CLEVELAND
RANGE MADE OR IMPLIED IN ANY MANUAL, LITERATURE, ADVERTISING BROCHURE OR OTHER MATERIALS.
CLEVELAND RANGE’S liability on any claim of any kind, including negligence, with respect to the goods or services covered
hereunder, shall in no case exceed the price of the goods or services, or part thereof, which gives rise to the claim. IN NO EVENT
SHALL CLEVELAND RANGE BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES
IN THE NATURE OF PENALTIES.
2
GENERAL INFORMATION ABOUT COMBIS
A. PRODUCT INFORMATION
Cleveland Range, LLC assigns two product identification numbers to each Combi: a model number
and a serial number. The model number identifies the product characteristics. The serial number
identifies the individual Combi.
1. Model Number
a. This manual covers the installation of the OEB and OES model gas powered Combis.
b. Model Number Key: “O” stands for the Combi series Oven, “E” or “G” designates Electric or Gas.
“B” designates Steam Generator, and “S” designates Spritzer. The first number designates the
number of shelves in the oven rack. The second number is either “.10” for 12” X 20” steam table
pans or “.20” for 18” X 26” full size sheet pans. For further information, contact your Convotherm by
Cleveland sales representative or Cleveland Range.
2. Serial Number and Equipment Record
During manufacture, Combis are assigned individual serial numbers. Please provide the following
information when you contact Cleveland Range or a qualified Cleveland Range authorized service
representative:
Serial Number________________________________________________________________
(Write the Serial Number of your Combi here.)
Model Number________________________________________________________________
(Write the Model Number of your Combi here.)
3. Product Information Plate
The Product Information Plate on the left side of the Combi lists the model, serial number, gas, electric,
and wiring requirements of the Combi. Figure 1-1 illustrates a typical Product Information Plate.
Figure 1-1
Typical Product Information Plate
3
INSTALLATION INSTRUCTIONS
A. GENERAL
This equipment should be installed only by qualified, professional plumbers, pipe fitters, and electricians.
1. The installation of this Combi must conform with:
a. The National Fuel Gas Code, ANSI Z223.1 / NFPA 54 (latest edition), or the
Natural Gas and Propane Installation Code CSA B1 49.1 as applicable.
b. The National Electrical Code, ANSI/NFPA 70 (latest edition), or the Canadian
Electrical Code, CSA C22.2 as applicable.
c. The Food Service Sanitation Manual of the Food and Drug Administration (FDA).
d. All applicable national, state, and local laws, codes, and regulations.
2. This equipment is to be installed to comply with the applicable federal, state, or local
plumbing codes.
3. Installation instructions must be read in their entirety before starting installation of a Combi.
4. Install the Combi according to the policies and procedures outlined in this manual.
DANGER
Improper installation, adjustment, alteration, service, or maintenance of a Combi, or
installation of a damaged Combi can result in DEATH, INJURY, EQUIPMENT DAMAGE, and
void the warranty.
NEVER install damaged Combis.
ALWAYS have qualified Cleveland Range authorized personnel install and service Combis.
5. Inspect the Combi for shipping damage.
a. Check carton and packing for shipping damage.
b. Note any damage on the shipping paperwork as soon as the carton arrives.
c. Unpack the Combi and check for shipping damage.
d. If the Combi is damaged or damage is suspected:
1) Inform your dealer at once.
2) Inform Cleveland Range in writing within 3 days.
3) Submit a Damage Claim to the Shipper.
4
B. INSTALLATION OF THE COMBI – General Instructions
General Instructions:
1. Select the Combi’s operating location.
2. Complete the water, drain, and electric lines before positioning and leveling the Combi.
3. Position and level the Combi.
4. Connect the utility lines after positioning and leveling the Combi.
5. Call Cleveland Range at 216-481-4900 for the Free Start-Up Program’s Performance
Checkout.
6. After Setup and Performance Checkout, the Combi should provide years of reliable
operation.
DANGER
Improper lifting can result in DEATH, INJURY, AND EQUIPMENT DAMAGE.
Use enough workers with training and experience lifting heavy equipment to place
Combis on supporting surfaces, and lift and handle Combis and acessories.
DANGER
Operating an out of level Combi can cause DEATH, INJURY, and EQUIPMENT DAMAGE.
Combis must be level both front-to-back and side-to-side in all installations.
NEVER operate an out of level Combi.
If a Combi is suspected to be out of level, shut it down at once and call you qualified
Cleveland Range authorized service agency at once.
WARNING
All clearance requirements above, below, and around the Combi are the same for noncombustible locations as for combustible locations.
Failure to maintain required clearances and additional distances as needed can result
INJURY and EQUIPMENT DAMAGE.
Consult manufacturers’ literature, and sales and service agencies as needed.
5
C. SPECIAL INSTRUCTIONS FOR CASTER EQUIPPED COMBI STANDS AND COMBIS
1. Read all instructions before beginning installation.
2. Level the floor if needed.
3. NOTE: Combis on caster-equipped stands have less adjustment for level than adjustable
foot equipped stands.
4. The front wheels of caster-equipped stands and Combis have locks. Check the caster
locks for function and position before installation.
5. Follow the separate instructions included with the Stand, Stacking Kit, or Caster Kit.
6. Make sure the Stand, Stacking Kit, or Caster Kit matches the Combi(s).
7. Use only genuine Cleveland Range Stands, Stacking Kits, Caster Kits, and replacement
parts.
8. Use of Stands, Stacking Kits, Caster Kits, and replacement parts other than genuine
Cleveland Range Stands, Stacking Kits, and Caster Kits and replacement parts can
result in injury and / or catastrophic equipment failure, and voids the Warranty.
9. The appliance must be secured to building structure, to prevent any strain on the utility
connections, and to help reduce the risk of electric shock.
10. The strain relief (restraining device) must be installed to limit the movement of the
appliance without depending on the connector and the quick-disconnect device or its
associated piping (gas, water, or electric). See separate instructions for attachment
location and other details.
11. Connect the strain relief (restraining device) BEFORE starting the Combi
12. If the strain relief (restraining device) must be disconnected, it must be reconnected
after the Combi has been returned to its originally installed position BEFORE restarting
the Combi.
13. Prepare the installation location as described in the Combi Installation Manual.
14. For GAS (OGB, OGS) Combis: The installation of the gas supply shall be made with a
connector that complies with the Standard for Connectors for Movable Gas Appliances,
ANSI Z21.69 / CSA 6.16, and a quick disconnect device that complies with the Standard
for Quick Disconnect Devices for Use With Gas Fuel, ANSI Z21.41 / CSA 6.9.
15. The appliance shall be installed using flexible conduit.
16. Mechanically secure the flexible conduit to the Combi’s electrical access hole.
6
SINCE 1922
INNOVATIVE STEAM COOKING SOLUTIONS
COMBI OVEN-STEAMER
by
Featuring the
MODEL:
c OGB-10.10
"Advanced Closed
System +3"
CAPACITY:
TEN (10) – 12" by 20" by 2 1/2" steam table pans
GAS Fired – with Steam Generator
ITEM NUMBER __________________________________________
JOB NAME / NUMBER __________________________________
Cooking Modes:
■ Hot Air
■ Steam
■ Combi
■
Retherm
by
■ "Cook & Hold"
■ "Delta T" slow cooking
■ "Crisp & Tasty"
Cleveland Standard Features:
■ "Advanced closed system" with "Crisp & Tasty" de-moisturizing feature
■ High efficiency,
by power burner heating system for hot air and steam
generator saves energy and provides fast heat up times
■ Fully insulated steam generator and cooking compartment for
maximum energy savings
■ Polished cooking compartment with coved corners for easy cleaning
■ Three (3) 12" x 20" wire shelves
■ Hinged fan guard and hinged removable pan racks
■ Two (2) speed auto reversing convection fan for even heat distribution
■ Space saving, easy to close "Disappearing Door"
■ Door latch with safety vent position and wear-free door switch
■ Vented, double glass door with integrated door stop and self
draining condensate drip pan
■ Easy to change, press-fit door seal
■ Oven light with shock resistant safety glass
■ Multipoint core temperature probe
■ Easy to use electronic controls for all operational functions
■ Self diagnostic system with full text message display
■ Easy to understand menu icons with bright graphics display
■ User friendly selector dial
■ Exclusive "Smart Key" for selecting option settings
■ Digital controls for temperature, time and core probe settings
■ Eight (8) "Press & Go" one step, recipe start buttons
■ Cook book library for up to 250 stored recipe programs, each
recipe capable of 20 steps
■ RS 232 connection for controlling one unit with a PC (personal computer)
■ Memory module automatically saves unit settings and recipes
■ Manual program override feature for operational settings
■ Smooth action hand shower for compartment cleaning
Gas Fired Steam Generator
■
■
■
■
Quiet, high efficiency, power burner heating system
Built-in automatic rinse system
Automatic fill and water level control
Automatic generator drain
Cleveland Range, LLC
Short Form Specifications
Shall be Cleveland Model: OGB-10.10 Combination Convection Oven /
Steamer with simple to operate electronic programmable controls for Hot Air,
Convection Steam, and Combination cooking modes, "Cook & Hold" and
"Delta T" slow-cooking capabilities, "Advanced Closed System" with "Crisp
& Tasty" de-moisturizing feature. Multiple cooking stage programs, stored
recipe library, multipoint core temperature probe, "Press & Go", one-step
recipe start buttons, "Smart Key" for selecting option settings, Two (2) speed
auto reversing convection fan. Quiet, high efficiency power burner heating
system; steam generator with automatic drain. "Disappearing Door".
Capacity for ten (10) 12" x 20" x 2 1/2" pans.
Options and Accessories
❐ ConvoClean automatic compartment washing system
❐ PC-HACCP software for establishing "HACCP controls" and automatic
documentation of the cooking process
❐ Equipment stand(s)
❐ Equipment stand(s) with Casters
❐ Stacking kit for mounting one (1) OGB-6.10 model on top of
one (1) OGB-10.10
❐ Lockable cover over operating controls for prison installations
❐ USB or RS 485 connection for networking and controlling up to 32 units
with a personal computer
❐ Propane gas option
❐ Flue diverter
❐ Plate rack for banquet operations
❐ Plate rack cart
❐ Thermal cover for plate or pan rack
❐ ConvoClean compartment cleaning solution
❐ ConvoCare concentrate for compartment rinse cycle
❐ "Dissolve" generator descaling solution
❐ Chicken Grill Rack
❐ 12" x 20" Wire Baskets for frying products
SECT. IIC PAGE 17
❐ Additional 12" x 20" Wire Shelves
0406
1333 East 179th
7 St., Cleveland, Ohio, U.S.A. 44110
Ph: 1-216-481-4900 Fx: 1-216-481-3782 Web Site: www.clevelandrange.com
36.70"
Model:
1.82"
38.98"
44.98"
1.82"
1.58"
38.98"
44.98"
2.52"
36.70"
The "Advanced Closed System"
2.52" offers the following advantages:
1.58"
■ Saves energy
■ Automatic moisture level adjustment
■ Low heat and steam emission to the kitchen
■ Automatically regulated steam injection
■ Enables immediate change into the steam mode
■ "Crisp & Tasty" demoisturizing function
OGB-10.10
Pan Capacity [Unit has 11 slide rails at 2.64" (67mm) apart]:
W1
10 (12" x 20" x 2 1/2") steam table pans
11 (12" x 20" x 1") steam table pans
11 (13" x 20") half size wire racks
11 (13" x 18") half size sheet pans
10 (12" x 20") frying baskets - (no wire racks needed)
W2
For Banquet Operations:
RC
W1
AV
E2
S
VIEW
Width - 47", Depth - 41", Height - FRONT
54"
Shipping Weight:
475 Lbs
3.39"
Shipping Dimensions:
(including packaging)
Required Clearances:
Rear - 2", Left Side - 4", Right Side - 2 1/2"
AV
• Allow for sufficient distance if a "high heat source" (i.e. Broiler) is located
next to the unit.
• Allow for sufficient clearance on left side for service access (contact the
W1 for recommendations).
factory service department
W1
E1
• Installation must comply with all local fire and health codes.
S
2.80"
AV
D
Agency Approvals:
S
Electrical Requirements:
UL - Gas, UL - Sanitation (NSF Standards)
W2
W2
2.80"
31.70"
CS
W2
E1
Width - 41.04", Depth - 34.50", Height - 45.68"
6.46"
2.60"
3.39"
10.79"
6.46"
FRONT VIEW
Unit Dimensions:
10.79"
D
Optional Plate Rack holds 32 plates
6.00"
31.70"
6.00"
120 volt, 11.7 amps, 60 Hz, single phase
D
D
RC
E1
D
D
E1
19.30"
W2
D
W2
RC
RC
RC
RC
CS
CS
CS
6.34"
CS
BOTTOM VIEW
2.01"
3.00"
4.97"
Drain Connection:
AV
RC
9.30"
AV
AV
S
CS
S
NOTES:
Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Cleveland Range equipment is built to comply with applicable standards for manufacturers.
8
S
G
AV
G
G
E1
S
W2
Cold Water (drinking water quality)
30 - 60 PSI
3.23"
30.20"
3/4" GHT-F (Female Garden Hose Connection)
CS
CS
D
W1
AV
W1
AV
Treated Water for Steam Generator
Venting:
23.
3
6.
S Untreated Water for Condenser and Hand Shower
W2
S
G
W2
2" Tube
G
D
G
E2
W1
1.19"
Water Connections:
Flow Pressure:
Water Inlets:
17.60"
G
D
AV
W1
W1
W1
S
W2
W2
W2
G
D
W1
6.07"
9.45"
12.45"
3.27"
30.20"
2.96"
17.60"
3.23"
E2
CS
Total Connected Load:
W1
Steam Generator:
RC
RC
Hot Air:
12.45"
23.63"
11.11"
1.19"
6.97"
TOP VIEW
3/4" NPT
2.80"
Natural Gas (Propane optional)
Natural Gas -6.96"
Min. 5.5" WC / Max. 14" WC
Propane Gas - Min. 11" WC / Max. 14" WC
75,700 BTU (68,000
11.11" BTU Propane)
68,200 BTU (61,000 BTU Propane)
75,700 BTU (68,000 BTU Propane)
Gas Connection:
Gas Type:
Gas Flow Pressure:
9.45"
G
2.96"
TOP VIEW
2.80"
D
D
RC
Exhaust Hood required
E1
E1
Gas Exhaust for Hot Air Heating
CS
E2
E2
W1
RCGas Exhaust for Steam Generator
AV
RC CSAir Vent
CS
*Connection for Rinse Cycle
CS
G
Low Pressure Safety Valve
AV
AV
*Available as an option E1
E2
G
G
W2
6.3
BOTTOM VIEW
RC
2.01"
*Connection for Cleaning
S Solution
S
S
19.
3.00"
4.97"
9.30"
SECT.
IIC
18
PAGE
0406
SINCE 1922
INNOVATIVE STEAM COOKING SOLUTIONS
COMBI OVEN-STEAMER
by
Featuring the
MODEL:
c OGS-10.10
"Advanced Closed
System +3"
CAPACITY:
TEN (10) – 12" by 20" by 2 1/2" steam table pans
GAS Fired – Boilerless
ITEM NUMBER __________________________________________
JOB NAME / NUMBER __________________________________
Cooking Modes:
■ Hot Air
■ Steam
■ Combi
■
Retherm
by
■ "Cook & Hold"
■ "Delta T" slow cooking
■ "Crisp & Tasty"
Cleveland Standard Features:
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
"Advanced closed system" with "Crisp & Tasty" de-moisturizing feature
High efficiency,
power burner heating system
by
Fully insulated cooking compartment for maximum energy savings
Polished cooking compartment with coved corners for easy cleaning
Three (3) 12" x 20" wire shelves
Hinged fan guard and hinged removable pan racks
Two (2) speed auto reversing convection fan for even heat distribution
Space saving, easy to close "Disappearing Door"
Door latch with safety vent position and wear-free door switch
Vented, double glass door with integrated door stop and self
draining condensate drip pan
Easy to change, press-fit door seal
Oven light with shock resistant safety glass
Multipoint core temperature probe
Easy to use electronic controls for all operational functions
Self diagnostic system with full text message display
Easy to understand menu icons with bright graphics display
User friendly selector dial
Exclusive "Smart Key" for selecting option settings
Digital controls for temperature, time and core probe settings
Eight (8) "Press & Go" one step, recipe start buttons
Cook book library for up to 250 stored recipe programs, each
recipe capable of 20 steps
RS 232 connection for controlling one unit with a PC (personal computer)
Memory module automatically saves unit settings and recipes
Manual program override feature for operational settings
Smooth action hand shower for compartment cleaning
Injection system for steam
Options and Accessories
❐ ConvoClean automatic compartment washing system
❐ PC-HACCP software for establishing "HACCP controls" and
automatic documentation of the cooking process
❐ Equipment stand(s)
❐ Equipment stand(s) with Casters
❐ Stacking kit for mounting one (1) OGS-6.10 model on top of
one (1) OGS-10.10
Cleveland Range, LLC
Short Form Specifications
Shall be Cleveland Model: OGS-10.10 Combination Convection Oven /
Steamer with simple to operate electronic programmable controls for Hot Air,
Convection Steam, and Combination cooking modes, "Cook & Hold" and
"Delta T" slow-cooking capabilities, "Advanced Closed System" with "Crisp
& Tasty" de-moisturizing feature. Multiple cooking stage programs, stored
recipe library, multipoint core temperature probe, "Press & Go", one-step
recipe start buttons, "Smart Key" for selecting option settings, two (2) speed
auto reversing convection fan. Quiet, high efficiency power burner heating
system; boilerless. "Disappearing Door". Capacity for ten (10) 12" x 20" x 2
1/2" pans.
❐ Lockable cover over operating controls for prison installations
❐ USB or RS 485 connection for networking and controlling up to 32
units with a personal computer
❐ Propane gas option
❐ Flue diverter
❐ Plate rack for banquet operations
❐ Plate rack cart
❐ Thermal cover for plate or pan rack
❐ ConvoClean compartment cleaning solution
❐ ConvoCare concentrate for compartment rinse cycle
❐ "Dissolve" generator descaling solution
❐ Chicken Grill Rack
❐ 12" x 20" Wire Baskets for frying products
❐ Additional 12" x 20" Wire Shelves
SECT.
IIC
45
PAGE
0406
1333 East 179th
9 St., Cleveland, Ohio, U.S.A. 44110
Ph: 1-216-481-4900 Fx: 1-216-481-3782 Web Site: www.clevelandrange.com
36.70"
The "Advanced Closed System" offers the following advantages:
■ Saves energy
■ Automatic moisture level adjustment
■ Low heat and steam emission to the kitchen
■ Automatically regulated steam injection
■ Enables immediate change into the steam mode
■ "Crisp & Tasty" demoisturizing function
1.82"
1.58"
38.98"
44.98"
2.52"
Model:
W1
W2
6.00"
D
3.39"
10.79"
6.46"
FRONT VIEW
W1
AV
RC
31.70"
W2
CS
E1
S
D
2.80"
AV
6.96"
A = Water hook up soft water G"
B = Water hook up cold water G"
For
Operations: hook
Optionalup
PlateDN50
Rack holds 32 plates
CBanquet
= Drainage
D Dimensions:
= Power hookWidth
up- 41.04", Depth - 34.50", Height - 45.68"
Unit
E = Potential equaliser
Shipping Dimensions:
Width - 47", Depth - 41", Height - 54"
F = Final
rinse hook up
(including
packaging)
G = Cleaner hook up
Shipping Weight:
475 Lbs
H = Air vent pipe
Required
Clearances:
Rearsafety
- 2", Left Side - 4", Right Side - 2 1/2"
I = Low
pressure
• Allow for sufficient distance if a "high heat source" (i.e. Broiler) is located
Jnext=toGas
W1up R"
the unit.hook
•K
Allow
sufficient clearance
left side for service access (contact the
= for
Exhaust
pipeongas
factory service department for recommendations).
• Installation must comply
W2 with all local fire and health codes.
Agency Approvals:
UL - Gas, UL - Sanitation (NSF Standards)
Electrical Requirements:
120 volt, 11.7 amps, 60 Hz, single phase
Do not connect to a G.F.I. outlet
G
Gas Connection:
Gas Type:
Gas Flow Pressure:
RC
23.63"
E1
W1
11.11"
W1
CS
E2
W2
AV
W1
W2
3.23"
3.27"
30.20"
9.45"
W2
G
G
D
3/4" NPT
Natural Gas (Propane optional)
Natural Gas - Min. 5.5" WC / Max. 14" WC
Propane Gas - Min. 11" WC / Max. 14" WC
Total Connected Load: W2
RC 75,700 BTU (68,000 BTU Propane)
Hot Air:
75,700 BTU (68,000 BTU Propane)
Water Connections:
Flow Pressure:
Water Inlets:
D
19.30"
D
E1
RC
W1
W1
D
CS
W1
AV
W1
D
W1
S
D
W2
6.07"
2.96"
12.45"
10 (12" x 20" x 2 1/2") steam table pans
11 (12" x 20" x 1") steam table pans
11 half size wire racks (13" x 20")
11 (13" x 18") half size sheet pans
10 (12" x 20") frying baskets - (no wire racks needed)
S
TOP VIEW
17.60"
OGS 10.10
Pan Capacity [Unit has 11 slide rails at 2.64" (67mm) apart]:
D
2.80"
1.19"
OGS-10.10
Cold Water (drinking water quality)
30 - 60 PSI
3/4" GHT-F (Female Garden Hose Connection)
Treated Water for Steam Production
W2
S
W2
Untreated Water for Condenser and Hand Shower
Drain Connection:
RC
2" Tube
Venting:
DG
D
Exhaust Hood required
CS
E1
Gas Exhaust for Hot Air Heating
AV
E2
Air Vent
RC
E2
W2
RC
CS
6.34"
RC
CS
CS
AV
RC
AV
CS
BOTTOM VIEW
2.01"
3.00"
4.97"
S
CS
S
9.30"
AV
NOTES:
Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Cleveland Range equipment is built to comply with applicable standards for manufacturers.
10
G
AV
SG
E1
*Connection for Cleaning Solution
S
RC
RC
*Connection for Rinse Cycle
Low Pressure Safety Valve
G
CS
CS
*Available as an option
E1
AV
AV
E2
S
S
S
E1
G
E2
G
SECT.
IIC
46
PAGE
0406
SINCE 1922
INNOVATIVE STEAM COOKING SOLUTIONS
COMBI OVEN-STEAMER
by
Featuring the
MODEL:
"Advanced Closed
System +3"
CAPACITY:
GAS Fired – with Steam Generator
c OGB-6.20
Seven (7) – 18" by 26" full size sheet pans or
Fourteen (14) – 12" by 20" by 2 1/2" steam table pans
ITEM NUMBER __________________________________________
JOB NAME / NUMBER __________________________________
Cooking Modes:
■ Hot Air
■ Steam
■ Combi
■
Retherm
by
■ "Cook & Hold"
■ "Delta T" slow cooking
■ "Crisp & Tasty"
Cleveland Standard Features:
■ "Advanced closed system" with "Crisp & Tasty" de-moisturizing feature
■ High efficiency,
by power burner heating system for hot air and steam
generator saves energy and provides fast heat up times
■ Fully insulated steam generator and cooking compartment for
maximum energy savings
■ Polished cooking compartment with coved corners for easy cleaning
■ Three (3) 26" x 20" wire shelves
■ Hinged fan guard and hinged removable pan racks
■ Two (2) speed auto reversing convection fan for even heat distribution
■ Space saving, easy to close "Disappearing Door"
■ Door latch with safety vent position and wear-free door switch
■ Vented, double glass door with integrated door stop and self
draining condensate drip pan
■ Easy to change, press-fit door seal
■ Oven light with shock resistant safety glass
■ Multipoint core temperature probe
■ Easy to use electronic controls for all operational functions
■ Self diagnostic system with full text message display
■ Easy to understand menu icons with bright graphics display
■ User friendly selector dial
■ Exclusive "Smart Key" for selecting option settings
■ Digital controls for temperature, time and core probe settings
■ Eight (8) "Press & Go" one step, recipe start buttons
■ Cook book library for up to 250 stored recipe programs, each
recipe capable of 20 steps
■ RS 232 connection for controlling one unit with a PC (personal computer)
■ Memory module automatically saves unit settings and recipes
■ Manual program override feature for operational settings
■ Smooth action hand shower for compartment cleaning
Gas Fired Steam Generator
■
■
■
■
Quiet, high efficiency, power burner heating system
Built-in automatic rinse system
Automatic fill and water level control
Automatic generator drain
Cleveland Range, LLC
Short Form Specifications
Shall be Cleveland Model: OGB-6.20 Combination Convection Oven / Steamer
with simple to operate electronic programmable controls for Hot Air, Convection
Steam, and Combination cooking modes, "Cook & Hold" and "Delta T" slowcooking capabilities, "Advanced Closed System" with "Crisp & Tasty" demoisturizing feature. Multiple cooking stage programs, stored recipe library,
multipoint core temperature probe, "Press & Go", one-step recipe start buttons,
"Smart Key" for selecting option settings, Two (2) speed auto reversing
convection fan. Quiet, high efficiency power burner heating system; steam
generator with automatic drain. "Disappearing Door". Capacity for seven (7) 18"
x 26" full size sheet pans, or fourteen (14) 12" x 20" x 2 1/2" pans.
Options and Accessories
❐ ConvoClean automatic compartment washing system
❐ PC-HACCP software for establishing "HACCP controls" and automatic
documentation of the cooking process
❐ Equipment stand(s)
❐ Equipment stand(s) with Casters
❐ Stacking kit for stacking two (2) OGB-6.20 models
❐ Stacking kit for mounting one (1) OGB-6.20 model on top of
one (1) OGB-10.20
❐ Universal pan-rack system to hold full size sheet pans without the use of wire
shelves
❐ Lockable cover over operating controls for prison installations
❐ USB or RS 485 connection for networking and controlling up to 32 units with a
personal computer
❐ Propane gas option
❐ Flue diverter
❐ Plate rack for banquet operations
❐ Plate rack cart
❐ Thermal cover for plate or pan rack
❐ ConvoClean compartment cleaning solution
❐ ConvoCare concentrate for compartment rinse cycle
❐ "Dissolve" generator descaling solution
❐ Chicken Grill Rack
❐ 12" x 20" Wire Baskets for frying products
SECT. IIC PAGE 21
❐ Additional 26" x 20" Wire Shelves
0406
❐ Special Baking Rack System
1333 East 179th
11St., Cleveland, Ohio, U.S.A. 44110
Ph: 1-216-481-4900 Fx: 1-216-481-3782 Web Site: www.clevelandrange.com
47.92"
30.12"
36.12"
30.12"
1.82"
1.58"
36.12"
2.52"
47.92"
The "Advanced Closed
2.52"System" offers the following advantages: 1.82"
1.58"
■ Saves energy
■ Automatic moisture level adjustment
■ Low heat and steam emission to the kitchen
■ Automatically regulated steam injection
■ Enables immediate change into the steam mode
■ "Crisp & Tasty" demoisturizing function
Model:
OGB-6.20
Pan Capacity [Unit has 7 slide rails at 2.64" (67mm) apart]:
7 (20" x 26") full size wire racks
14 (13" x 18") half size sheet pans - on wire racks
6.00"
14 (12" x 20" x 1") steam table pans
W2
For Banquet Operations:
3.39"
7 (18" x 26") full size sheet pans - on wire racks
14 (12" x 20" x 2 1/2") steam table pans
14 (12" x 20") frying Baskets - (no wire racks needed)
FRONT VIEW
Optional Plate Rack holds 42 plates
Width - 52.26", Depth - 43.24", Height - 36.82"
Shipping Dimensions:
(including packaging)
Width - 58", Depth - 49", Height - 45"
Shipping Weight:
485 Lbs
10.79"
3.55"
Unit Dimensions:
D
10.79"
7.49"
FRONT VIEW
3.39"
6.00"
7.49"
W1
AV
AV
E1
RC
S
W2
2.80"
CS
D
AV
TOP VIEW
G
Gas Connection:
Gas Type:
Gas Flow Pressure:
10.40"
6.93"
D
G
2.96"
D
W2
W2
W2
G
D
W1
29.61"
D
E1
Drain Connection:
W2
Venting:
E2
W1
W2
3.90"
CS
BOTTOM VIEW
3.00"
4.97"
RC
RC
RC
CS
CS
CS
AV
RC
10.87"
AV
AV
S
CS
S
S
NOTES:
Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Cleveland Range equipment is built to comply with applicable standards for manufacturers.
12
G
AV
G
G
E1
S
E1
E1
1.19"
RC
31.50
CS Cold Water (drinking water quality)
CS
3.23"30 - 60 PSI
41.42"
3/4" GHT-F (Female Garden Hose Connection)
D
W1
AV
W1
AV
S
W2
S
W2
3.27
6.93
Treated Water for Steam Generator
Untreated Water for Condenser and Hand Shower
G
2" Tube
G
D
G
D
8.55"
3/4" NPT
Natural12.68"
Gas (Propane optional)
Natural Gas - Min. 5.5" WC / Max. 14" WC
Propane Gas - Min. 11" WC / Max. 14" WC
75,700 BTU (68000 BTU Propane)
68,200 BTU (61,000 BTU Propane)
75,700 BTU (68,000 BTU Propane)
W2
Water Connections:
Flow Pressure:
Water Inlets:
10.40"
41.42"
AV
W1
W1
W1
S
27.29"
3.23"
3.27"
14.26"
CS
E2
Total Connected Load:
W1
Steam Generator:
RC
RC
Hot Air:
21.19"
E1
2.96"
31.50"
RC
14.26"
UL - Gas, UL - Sanitation (NSF Standards)
D
12.68"
21.19"
W2
W2
Electrical Requirements: 120 volt, 11.7 amps, 60 Hz, single phase
TOP VIEW
Do not connect to a G.F.I.D
outlet
2.80"
8.55"
27.29"
Agency Approvals:
S
2.80"
1.19"
Required Clearances:
Rear - 2", Left Side - 4", Right Side - 2 1/2"
• Allow for sufficient distance if a "high heat source" (i.e. Broiler) is located
E1
next to the unit.
• Allow for sufficient clearance on left side for service access (contact the
S
W1 for recommendations).
factory service department
W1
• Installation must comply with all local fire and health codes.
2.80"
W1
40.44"
40.44"
E2
D
RC
Exhaust Hood required
D
E1
E1
Gas Exhaust for Hot Air Heating
W1
E2
E2
Gas Exhaust for Steam Generator
W2
AV
RC
Air Vent
29.61
CS
RC
CS
RC
3.00"
*Connection for Cleaning
S Solution
4.97"
CS
*Connection for Rinse Cycle
CS
3.90
BOTTOM VIEW
10.87"
G
Low Pressure Safety Valve
AV
AV
*Available as an option E1
S
S
E2
G
G
SECT.
IIC
22
PAGE
0406
SINCE 1922
INNOVATIVE STEAM COOKING SOLUTIONS
COMBI OVEN-STEAMER
by
Featuring the
MODEL:
"Advanced Closed
System +3"
CAPACITY:
GAS Fired – Boilerless
c OGS-6.20
Seven (7) – 18" by 26" full size sheet pans or
Fourteen (14) – 12" by 20" by 2 1/2" steam table pans
ITEM NUMBER __________________________________________
JOB NAME / NUMBER __________________________________
Cooking Modes:
by
■ Hot Air
■ Steam
■ Combi
■ Retherm
■ "Cook & Hold"
■ "Delta T" slow cooking
■ "Crisp & Tasty"
Cleveland Standard Features:
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
"Advanced closed
system" with "Crisp & Tasty" de-moisturizing feature
by
High efficiency, power burner heating system
Fully insulated cooking compartment for maximum energy savings
Polished cooking compartment with coved corners for easy cleaning
Three (3) 26" x 20" wire shelves
Hinged fan guard and hinged removable pan racks
Two (2) speed auto reversing convection fan for even heat distribution
Space saving, easy to close "Disappearing Door"
Door latch with safety vent position and wear-free door switch
Vented, double glass door with integrated door stop and self
draining condensate drip pan
Easy to change, press-fit door seal
Oven light with shock resistant safety glass
Multipoint core temperature probe
Easy to use electronic controls for all operational functions
Self diagnostic system with full text message display
Easy to understand menu icons with bright graphics display
User friendly selector dial
Exclusive "Smart Key" for selecting option settings
Digital controls for temperature, time and core probe settings
Eight (8) "Press & Go" one step, recipe start buttons
Cook book library for up to 250 stored recipe programs, each
recipe capable of 20 steps
RS 232 connection for controlling one unit with a PC (personal computer)
Memory module automatically saves unit settings and recipes
Manual program override feature for operational settings
Smooth action hand shower for compartment cleaning
Injection system for steam
Options and Accessories
❐ ConvoClean automatic compartment washing system
❐ PC-HACCP software for establishing "HACCP controls" and
automatic documentation of the cooking process
❐ Equipment stand(s)
❐ Equipment stand(s) with Casters
❐ Stacking kit for stacking two (2) OGS-6.20 models
Cleveland Range, LLC
Short Form Specifications
Shall be Cleveland Model: OGS-6.20 Combination Convection Oven /
Steamer with simple to operate electronic programmable controls for Hot Air,
Convection Steam, and Combination cooking modes, "Cook & Hold" and
"Delta T" slow-cooking capabilities, "Advanced Closed System" with "Crisp
& Tasty" de-moisturizing feature. Multiple cooking stage programs, stored
recipe library, multipoint core temperature probe, "Press & Go", one-step
recipe start buttons, "Smart Key" for selecting option settings, two (2) speed
auto reversing convection fan. Quiet, high efficiency power burner heating
system; boilerless. "Disappearing Door". Capacity for seven (7) 18" x 26" full
size sheet pans, or fourteen (14) 12" x 20" x 2 1/2" pans.
❐ Stacking kit for mounting one (1) OGS-6.20 model on top of
one (1) OGS-10.20
❐ Universal pan-rack system to hold full size sheet pans without the
use of wire shelves
❐ Lockable cover over operating controls for prison installations
❐ USB or RS 485 connection for networking and controlling up to 32
units with a personal computer
❐ Propane gas option
❐ Flue diverter
❐ Plate rack for banquet operations
❐ Plate rack cart
❐ Thermal cover for plate or pan rack
❐ ConvoClean compartment cleaning solution
❐ ConvoCare concentrate for compartment rinse cycle
❐ "Dissolve" generator descaling solution
❐ Chicken Grill Rack
❐ 12" x 20" Wire Baskets for frying products
❐ Additional 26" x 20" Wire Shelves
SECT. IIC PAGE 49
0406
❐ Special Baking Rack System
1333 East 179th
13St., Cleveland, Ohio, U.S.A. 44110
Ph: 1-216-481-4900 Fx: 1-216-481-3782 Web Site: www.clevelandrange.com
47.92"
2.52"
The "Advanced Closed System" offers the following advantages:
■ Saves energy
■ Automatic moisture level adjustment
■ Low heat and steam emission to the kitchen
■ Automatically regulated steam injection
■ Enables immediate change into the steam mode
■ "Crisp & Tasty" demoisturizing function
1.82"
36.12"
30.12"
1.58"
OGS 6.20OGS-6.20
Model:
W1
6.00"
W2
7 (20"
full size wire racks
7 (18"water
x 26") full sizeG"
sheet pans - on wire racks
B x =26") Water
hook up cold
14 (13" x 18") half size sheet pans - on wire racks 14 (12" x 20" x 2 1/2") steam table pans
C
=
Drainage
hook
up
DN50
14 (12" x 20" x 1") steam table pans
14 (12" x 20") frying Baskets - (no wire racks needed)
D = Power hook up
3.39"
For
Operations:equaliser
Optional Plate Rack holds 42 plates
EBanquet
= Potential
D
10.79"
7.49"
FRONT VIEW
A Capacity
= Water
uprails
soft
water
G"apart]:
Pan
[Unit hook
has 7 slide
at 2.64"
(67mm)
40.44"
AV
E1
W1
RC
S
W2
2.80"
CS
D
AV
F = Final rinse hook
up
Width - 52.26", Depth - 43.24", Height - 36.82"
G = Cleaner hook up
Shipping
Dimensions:
H = Air
vent pipe Width - 58", Depth - 49", Height - 45"
(including packaging)
I = Low pressure safety
J = Gas
hook up 485
R" Lbs
Shipping
Weight:
K = Exhaust pipe gas
Unit Dimensions:
Required Clearances:
Rear - 2", Left Side - 4", Right Side - 2 1/2"
• Allow for sufficient distance if a "high heat source" (i.e. Broiler) is located
W1
next to the unit.
• Allow for sufficient clearance on left side for service access (contact the
factory service department for recommendations).
• Installation must comply
W2 with all local fire and health codes.
Agency Approvals:
UL - Gas, UL - Sanitation (NSF Standards)
D
TOP VIEW
2.80"
S
Electrical Requirements:
120 volt, 11.7 amps, 60 Hz, single phase
Do not connect to a G.F.I. outlet
G
Gas Connection:
Gas Type:
Gas Flow Pressure:
8.55"
31.50"
12.68"
RC
E1
W1
W1
CS
E2
W2
6.93"
10.40"
14.26"
21.19"
3.27"
41.42"
D
W2
W1
AV
D
E1
RC
Cold Water (drinking water quality)
30 - 60 PSI
3/4" GHT-F (Female Garden Hose Connection)
Treated Water for Steam Production
S
W2
W2
Untreated Water for Condenser and Hand Shower
Drain Connection:
RC
2" Tube
Venting:
DG
D
Exhaust Hood required
29.61"
RC
D
CS
W1
AV
W1
S
D
W2
W1
1.19"
Water Connections:
Flow Pressure:
Water Inlets:
D
W1
W2
DG
G
2.96"
27.29"
3.23"
3/4" NPT
Natural Gas (Propane optional)
Natural Gas - Min. 5.5" WC / Max. 14" WC
Propane Gas - Min. 11" WC / Max. 14" WC
Total Connected Load: W2
RC 75,700 BTU (68,000 BTU Propane)
Hot Air:
75,700 BTU (68,000 BTU Propane)
W1
CS
E1
Gas Exhaust for Hot Air Heating
AV
E2
Air Vent
E2
RC
W2
CS
3.90"
CS
RC
CS
AV
BOTTOM VIEW
3.00"
RC
AV
CS
4.97"
S
10.87"
CS
S
AV
NOTES:
Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Cleveland Range equipment is built to comply with applicable standards for manufacturers.
14
G
AV
SG
*Connection for Cleaning Solution
S
RC
*Connection for Rinse Cycle
RC
Low Pressure Safety Valve
G
CS
CS
*Available as an option
E1
AV
AV
E1
E2
S
S
S
E1
G
E2
G
SECT.
IIC
50
PAGE
0406
CONTROL PANEL
BASIC OPERATION
A. QUICK START GUIDE
ALWAYS PRE-HEAT THE OVEN CHAMBER!
1. Switch on with key (1).
2. Select cooking mode with keys (2-5).
3. Press key (6) to start.
OR
1. Press key (18) and rotate Selector Dial (23) to set oven
temperature.
2. Press key (19) and rotate Selector Dial (23) to set
cooking time.
OR
1. Press key (20) and rotate Selector Dial (23) to set core
temperature.
ALL
1. Press key (6) to start the Combi.
2. To change the settings while cooking: press keys (18)
OR (19) OR (20) and adjust the settings with the
Selector Dial (23).
3. When the buzzer sounds press key (6) or open the
door.
NOTES: See “CONTROL PANEL DETAIL VIEW” in
Chapter 4, Section B for detailed descriptions of control
panel functions.
Figure 4-1a
Control Panel
15
B. CONTROL PANEL DETAIL VIEW
Note: Item numbers correspond to numbers on the
control panels in Figure 4-1b
1. ON/OFF
When the Combi is turned ON:
• Self-diagnosis is performed.
• Oven light turns on.
• Steam generator fills and heats (OEB and OGB
models).
Cooking Modes
2. Steam
• Oven temperature is continuously variable between
86°F and 248°F.
3. Combi Hot Air and Steam
• Oven temperature is continuously variable between
212°F and 482°F.
4. Hot Air
• Oven temperature is continuously variable between
86°F and 482°F.
5. Retherm
• Oven temperature is continuously variable between
248°F and 320°F.
6. Start/Stop
• Start cooking modes and recipes.
• Stop the cooking activity.
• Escape or Exit Smart Key functions
Programming / Help
7. Cookbook
• Call up, exit cookbook.
• View a list of stored recipes in the display.
8. Smart Key
• Set Extra Functions.
• Set-Up the Combi.
• Enter Sub-Menus.
9. Edit
• Create, change, copy, and delete recipes.
Figure 4-1b
Control Panel
16
• Page / Scroll one step forward or
back in programming mode.
Function Indicators
• Light up when function or activity is engaged:
23. Selector Dial
10. Reduced Power
11. Burner or Electric Heating ON
12. Reduced Fan Speed
13. Cooking Mode Engaged
14. Button Lock
15. Crisp & Tasty Engaged
16. Program Protection
• Set: Oven temperature, cooking time, core
temperature, recipe name, recipe number.
• Select Smart Key functions, editing
functions and recipes in the cookbook.
24. Press & Go Keys
• Start saved recipes with one key.
• LED below key lights up when
corresponding recipe is started.
17. Display
• Display in normal mode:
• Date.
• Time.
• Oven Temperature.
• Cooking Time
• Core Probe Temperature.
• Display in programming mode:
• Clear text.
• Memory.
• Symbols.
Notes:
Settings
18. Oven Temperature
• Set the nominal oven temperature.
• View the actual or nominal oven
temperature.
19. Cooking Time
• Set the cooking time from 1 minute to 9
hours, 59 minutes using the Selector Dial.
• Set Continuous Mode
1. At 9:59 or 0:01, release the Selector Dial.
2. Turn the Selector Dial again to the left
or right.
• See the actual or nominal cooking time.
• See elapsed cooking time when using
Core Temperature mode.
20. Core Temperature
• Set the nominal core temperature.
• See the actual or nominal core
temperature.
• See the actual core temperature during
cooking time mode.
21 & 22. Scroll Left and Scroll Right
17
•
Magnetic door switch
If the oven door is opened during
operation, the magnetic door switch
automatically interrupts the recipe. The
timer stops. After closing the oven door,
the Combi automatically continues the
recipe. If the oven door is opened when
the buzzer sounds at the end of a
recipe, it automatically switches off.
•
Operate controls with hands only!
AT THE END OF THE DAY OR SHIFT
A. Cleaning the Oven Chamber
CAUTION
Clean the oven chamber at least once per day or more frequently as needed
Failure to clean the Combi properly and regularly can cause equipment damage.
Damage caused by improper cleaning will invalidate the Warranty!
1. Cleaning – General
a. Regular cleaning of the Combi after use, inside and out, helps guarantee many years of
satisfaction from your Combi.
b. Clean and maintain the Combi ONLY when the Combi is cold.
c. Use the hand shower only inside the oven chamber.
d. Clean the outside the Combi by hand.
e. Never use the hand shower, hose, pressure washer or similar device on the outside of
the Combi.
f. NEVER spray anything on or into the air intakes or outlets of the Combi.
g. Do NOT use hoses, pressure washers, high-pressure cleaners, or water jets to clean
inside the Combi oven chamber.
h. Do NOT spray water into a hot oven chamber.
i. Use only genuine Convotherm by Cleveland and Cleveland Range cleaning and
descaling products. Follow the instructions and heed and obey the warnings on the
labels. Other products can cause injury, present heath hazards, and damage the Combi.
j. Never use irritant, acidic, highly alkaline cleaners, high-alcohol, chlorine, chlorinated, or
abrasive cleaning agents, scrapers, or abrasive materials to clean the Combi.
k. Poor water quality can cause discoloration inside the oven chamber. Remove these
discolorations with CONVOCare. Spray CONVOCare on the affected surfaces in a COLD
oven chamber, wait 10 minutes, wipe off with a soft cloth or sponge, and begin cleaning
as usual.
l.
Damage caused as a result of improper cleaning voids the warranty.
2. Semi-Automatic and Automatic Cleaning - General
a. If the oven chamber is very heavily soiled, additional manual cleaning may be necessary.
b. Depending on the level of soiling of the oven chamber, the engaging frames and grills
may be left in the oven during the automatic cleaning process.
c. Do NOT interrupt the semi-automatic or automatic cleaning process.
18
WARNING
When working with cleaning agents, nozzle rinsing fluid and spray bottles: Wear
suitable clothing, protective gloves and protective goggles to help protect from
splashes and spills. Failure to do so can result in chemical burns on skin and in eyes.
WARNING
Read, understand, and heed and obey all instructions and safety
information found on cleaning agent labels, Material Safety Data Sheets,
and related documents and sources. Failure to do so can result in death,
injury, and equipment damage.
3. Manual Cleaning of the Oven Chamber
a. Clean the Combi daily to prevent discoloration and corrosion of the stainless steel.
1) Avoid scratching the oven chamber or engaging frame.
2) Scratches can collect soil and / or allow corrosion to begin.
3) Do NOT use harsh or abrasive cleaning agents, scouring pads, or scrapers.
b. Clean the fan guard and the fan area behind the fan guard at the same time.
1) Release the quick-action locks on the oven racks and fan guard.
2) Pivot the oven racks and fan guard out into the oven chamber.
3) After cleaning, push the oven racks and fan guard closed and fix them in place with
the quick-action locks.
CAUTION
Do NOT use U-Shaped racks that are bent or otherwise damaged in any
way. Pans and accessories placed in damaged racks can tip and spill,
causing burns, injuries and/or equipment damage
c.
4) Make sure that the U-Shaped racks do not become bent; otherwise grills, racks,
containers and accessories will no longer be safely supported. If U-Shaped racks
become bent then remove the Combi from service and contact your qualified
Cleveland Range authorized service representative at once.
Clean the interior of the of the double glass doors daily.
1) Release the quick-action locks on the door glass.
2) Clean the glass with a non-abrasive cleaner and a soft cloth.
3) Do not use harsh or abrasive cleaning agents, scouring pads, or scrapers because
they will damage the glass.
d. Regular cleaning of the hygienic plug-in gasket (door gasket) increases service life.
1) Wait for the gasket to cool.
2) Clean the gasket with mild, scent free dish detergent and a soft cloth.
3) Do not use harsh or abrasive agents, scouring pads or scrapers because they will
damage the gasket.
4) Air dry the gasket.
19
e. Clean the Bypass Measuring Aperture. (Opening in the oven
chamber on the left-hand side, slightly below the door latch.
See diagram.)
1) Spray with CONVOClean.
2) Rinse clean with the hand shower.
f. Remove and clean the drain cover.
1) Clean food residue and drippings from the tray and
drain in the oven chamber.
2) Spray on original CONVOClean oven chamber cleaner and
allow it to take effect.
3) Rinse thoroughly with the hand shower.
g. Clean the drain and make sure that it is not
blocked.
h. Clean the demoisturizing tray (trough shaped area
under the drain cover).
Bypass
Drain Cover and Drain
i.
Clean the door drip tray, appliance drip trays and accessory drip trays.
NOTES:
•
If a white deposit forms inside the oven chamber, the water treatment system is not
correctly set, or the addition of a water treatment system is required. To remove this
deposit, use vinegar and a soft cloth.
•
Ask your qualified Cleveland Range authorized service representative about adding or
setting a water treatment system.
20
B. Semi-Automatic Cleaning of the Oven Chamber
NOTE: Do NOT press the Start/Stop key while using the Semi-automatic Cleaning process.
This stops the cleaning process.
WARNING
The Semi-Automatic Cleaning process is designed to be started when the
oven chamber temperature is at or below 158°F. Death, injury, and equipment
damage can result from starting the Semi-Automatic Cleaning process when
the oven chamber is above 158°F.
1. Before starting the Semi-Automatic Cleaning process, make sure the oven chamber is below
158°F by stopping all processes and pressing the Temperature key twice to view the actual
temperature.
a. If the oven chamber is above 158°F then open the Combi door and wait 15 minutes.
b. Check the oven temperature again.
1) If the oven temperature is at or below 158°F then go to Step 2.
2) If the oven temperature is still above 158°F then wait 15 more minutes and check the
oven chamber temperature. Repeat this step as needed until the oven chamber
temperature is at or below 158°F and then go to Step 2.
2. See separate instruction sheet P/N 260AYM, “One-Hand Sprayer with Telescoping Wand,” for
safety information, detailed instructions for using the sprayer, P/N 111598, and other
information.
3. Always wear appropriate protective clothing and equipment when using this Sprayer, including
protective gloves and goggles.
4. Close and latch the Combi door.
5. If the Combi is OFF, turn it ON.
6. Press the Smart Key. Various options appear in the display.
.
7. Use the Selector Dial to select “Cleaning”
8. Confirm by pressing the Smart Key.
9. Confirm “Yes” with the Smart Key. The semi-automatic cleaning process starts.
10. Semi-automatic cleaning uses cooking modes to assist the cleaning process. The display
shows the nominal values for the cooking modes.
a. The first step is Hot Air mode at 158°F for 10 minutes, followed by a Signal Tone.
11. After the first Signal Tone, open the oven door, and follow instruction sheet in P/N 260AYM to
spray the oven chamber, drain, grills, plates etc. with original Convotherm by Cleveland
CONVOClean.
12. Close and latch the Combi door and allow the CONVOClean to take effect. The SemiAutomatic Cleaning mode continues to run.
a. The second step is Steam mode at 86°F for 10 minutes, followed by a Signal Tone.
13. After the second Signal Tone, clean behind the fan guard and the fan area.
a. Release the quick-action locks on the oven racks and fan guard.
b. Swing the oven racks and fan guard into the oven chamber.
c. After cleaning, swing the oven racks and fan guard closed and fix it in place with the quick-action
locks.
14. Close and latch the Combi door. The Semi-Automatic Cleaning mode continues automatically.
21
15.
16.
17.
18.
a. The third step is Steam mode at 86°F for 1 minute. No action is needed.
b. The fourth step is Steam at 212°F for 10 minutes, followed by a Signal Tone.
Turn OFF the Combi when the Signal Tone sounds.
Use the hand shower to rinse thoroughly the oven chamber, accessories, and behind the fan guard.
In the case of severe staining or soiling, repeat the cleaning process.
After use or after cleaning, leave the Combi door open.
22
C. CONVOClean Automatic Cleaning System (optional):
NOTES:
•
Do NOT interrupt the automatic cleaning process. Interrupting and restarting the
Automatic Cleaning System with the ON/OFF key may start a 6 minute forced rinsing of
the oven chamber to remove any CONVOClean and CONVOCare residue when the
ON/OFF key is turned back ON. The Signal Tone sounds at the end of the forced rinsing
cycle and the Combi is ON.
•
Do not open the Combi door during the automatic cleaning process, unless the
instruction “Open the door” and “close the door,” appears in the display.
•
Pre-clean manually to save water and CONVOClean by selecting a lower cleaning
setting.
•
If the security questions are not answered within 5 seconds, the Combi resets itself to the
query level and will not start.
•
If the message “No cleaner pressure” appears, check that there is enough CONVOClean
and/or CONVOCare in the correct containers. Refill them if necessary (red hose for
CONVOClean, and blue or white hose for CONVOCare).
CAUTION
Always make sure the cleaning agent containers are correctly connected to the Combi
CONVOClean => RED
CONVOCare => BLUE or WHITE
A. See P/N 260AZA, “Instructions for CONVOClean System Start-up Kit,” for hose attachment,
solution mixing, and other information.
B. The CONVOClean Automatic Cleaning Process
1. The oven chamber must be cold before starting this process. If the oven chamber is still
hot, the error message, “oven temp too hi / please wait” appears in the display. If this
error message appears, open the Combi door, wait 15 minutes and then try to start the
automatic cleaning process. Repeat as needed.
2. Before starting, remove large pieces food or cooking residue from the oven chamber to
help prevent the drain from becoming blocked.
3. Check the level of Convotherm by Cleveland CONVOClean and CONVOCare.
a. The containers must be full.
b. The suction pipes must be located in the fluid.
c. The hoses must be properly attached to the Combi.
4. Press the Smart Key. Various options appear in the display.
.
5. Use the Selector Dial to select “CONVOClean system”
6. Confirm by pressing the Smart Key.
7. PRESS the Temperature key and select the cleaning level (1-4) with the Selector Dial.
Approximate run times are listed to help plan use of the CONVOClean system. Times
may vary by +/- 15 minutes.
1
“Light Soiling”
55 minutes.
2
“Medium Soiling”
1 hour and 30 minutes.
23
3
4
“Strong Soiling”
‘Strong Soiling – Shining+”
2 hours.
2 hours and 45 minutes.
8. Press the Smart Key.
9. “Food inside oven?” appears in the display.
10. If the oven is empty, then answer “No.”
11. Confirm by pressing the Smart Key.
12. “Start auto-cleaning?” appears in the display.
13. Answer “Yes.”
14. Confirm by pressing the Smart Key.
15. The CONVOClean system starts.
16. The instruction “open the door” appears in the display to check the function of the
magnetic door switch.
17. Open the Combi door.
18. The instruction “close the door,” appears in the display to check the function of the
magnetic door switch.
19. Close the door.
20. The self test “water supply open?” appears in the display. If the water supply is on (open),
then the self test question disappears from the display.
a. If “water supply open?” does not disappear from the display, or “not enough water”
appears in the display, then check the water supply.
b. The CONVOClean system resumes running after the water supply is restored.
21. “Cleaning in progress” appears in the display and the CONVOClean process runs.
22. The Signal Tone sounds at the end of the CONVOClean cycle and “end of cleaning”
appears in the display.
23. Press the Start/Stop key to stop the Signal Tone and end the CONVOClean process.
24. The Combi is ON and ready to use.
25. After use or after cleaning, leave the Combi door open.
24
DESCALE STEAM GENERATOR
A. GENERAL INFORMATION
1. Steam generators should be descaled at least once a month, depending on scale buildup. If
you have serious steam generator scale buildup, a water treatment system should be
installed for the steamer. If this is not possible, the frequency of descaling should be
increased.
2. Cleveland Range, recommends the use of DISSOLVE® Descaler Solution, Cleveland
Range Part Number 106174. No other system of steamer descaling should be used.
3. NOTE: Part No. 106174 is the Part No. for a case (6 1-gallon containers) of DISSOLVE®
descaler.
4. THESE INSTRUCTIONS ARE FOR USE WITH DISSOLVE® DESCALER SOLUTION
Cleveland Range Part Number 106174 ONLY.
5. Health Hazard Data, Effects of Overexposure – This product may cause a burning
sensation to eyes or skin.
6. Emergency and First Aid Procedures - In case of eye contact, immediately flush eyes with
plenty of water. If irritation persists, seek medical attention. In case of skin contact: wash with
soap and water. If inhaled, remove to fresh air. If burning persists, call a physician. If
swallowed, drink 1 or 2 glasses of water and call a physician.
7. Spill or Leak Procedures – Rinse with plenty of water to dilute. Sodium carbonate or
calcium carbonate may be used to soak up liquid. Spent material is considered nonhazardous and may be disposed of in a sewer system with water flush.
WARNING
The liquid solution in Cleveland Range Descaler Solution Part No. 106174, “DISSOLVE® Descaler
Solution,” can be harmful if not handled properly.
Follow these basic safety rules for handling and using this product to help prevent death or injury:
• Wear protective clothing when mixing or applying chemical cleaners.
• Wear rubber gloves, and OSHA approved eye protection when descaling to help avoid injury.
• Avoid breathing fumes. If liquid comes in contact with skin, wash with soap and water.
• If chemical contacts eyes, flush with water. If irritation persists, seek medical attention
• If chemical is swallowed or ingested, drink 1 or 2 glasses of water and call a physician.
Failure to do so can result in death or injury.
CAUTION
Use ONLY the DISSOLVE® Descaler method using Part No. 106174 to descale the Combi.
Read, understand, and follow both the descaling procedure instructions and warnings, and the
instructions and warnings on the DISSOLVE® label and MSDS.
Injury, equipment damage, and property damage can result from using other descaling systems
and/or failing to follow the descaling procedure and DISSOLVE® instructions and warnings.
25
DANGER
Do NOT heat the Combi during descaling.
Death, injury, equipment and property damage can result.
WARNING
This procedure is slightly different depending on the model
being descaled. This entire procedure should be read and fully
understand as it applies to the model being descaled, before
beginning the actual descaling operation.
B. GENERAL SAFETY FOR DESCALING
1. Always wear suitable protective clothing including appropriate gloves, and eye protection.
2. Read, understand, heed and obey and obey and obey, and follow all directions on the descaler label,
MSDS, and related documents
3. Never operate the Combi when descaler has been applied or while descaling.
4. Descale only when the Combi is cold.
5. Immediately wipe up any leaked or spilled descaling fluid.
C. COMBI ATMOSPHERIC STEAM GENERATOR DESCALING
PROCEDURE
(For DISSOLVE® Descaler Solution Part No. 106174)
This procedure takes approximately 3 hours to complete.
Do NOT heat the Combi during descaling.
1. Turn ON the Combi at the Control Power Service Disconnect
switch located below the hand shower.
2. Turn ON the Combi with the ON/OFF key.
3. Open the door to the cooking compartment.
4. Run a manual steam generator rinse cycle.
To Empty and Rinse the Steam Generator:
a. Press the Smart Key.
Figure 6-1
b. Select “Manual Steam Generator Rinse” with the
Selector Dial.
Descaling Port
c. Confirm “Yes” with the Smart Key.
Located at Right Rear of the Combi
d. Steam generator rinses and begins to refill to
operating level.
4. Remove the cap from the descale port located at the top
of the Combi (See Figure 6-1).
5. While the steam generator is filling with water, use a funnel (NOT INCLUDED) to
add 3/4 gallon of DISSOLVE® descaler solution into the descaling port of 20.20
Combis, and 1/2 gallon for all other models
26
•
•
While adding liquid to the steam generator through the descaler inlets, pour slowly to
avoid overflow.
Wipe up any spills at once to avoid etching.
6. After the automatic fill cycle has ended, turn OFF the Combi with the ON/OFF key, and at
the Control Power Service Disconnect switch located below the hand shower. See Figure
6-2.
7. Add cold tap water through the descale port until descaling solution enters the cooking
compartment through the steam port or until the descaling port overflows (water required
varies depending on the Model).
•
Wipe up any spills and overflows.
8. Let the Descaler work for 1 hour.
9. Turn the Combi ON at the Control Power Service Disconnect switch located below the
hand shower. See Figure 6-2.
10. Turn ON the Combi with the ON/OFF key.
11. Run a manual steam generator rinse cycle (Step 4).
12. After the automatic fill cycle has ended, turn OFF the Combi with ON/OFF key, and at the
Control Power Service Disconnect switch located below the hand shower. See Figure 62.
13. Add water through the descale port until water enters the cooking compartment through
the steam port or until the descaling port overflows (water required varies depending on
the Model) to rinse descaler from the area above the normal water fill level.
14. Replace the descale port cap.
15. Turn the Combi ON at the Control Power Service Disconnect switch located below the
hand shower. See Figure 6-2.
16. Turn ON the Combi with the ON/OFF key.
17. After the Automatic Fill ends, run a manual steam generator rinse cycle (See Step 4).
18. Run Combi mode for 30 minutes at 212° F with Crisp & Tasty function.
19. Close the cooking compartment door.
a. Press Combi key.
b. Press Temperature key.
c. Set temperature with Selector Dial to 212° F.
d. Press Time key.
e. Set time with the Selector Dial for 30 minutes.
f. Press Smart Key Various options appear in the display.
g. Select “Crisp & Tasty” with the Selector Dial.
h. Select the Crisp & Tasty level to “high demoisturizing – continuous” with the Selector
Dial.
i. Confirm “Yes” with Smart Key.
appears in the display.
j. The Crisp & Tasty icon
k. Press the Start/Stop key to start.
l. Signal Tone sounds and steaming stops after 30 minutes.
m. Press the Start/Stop key to end the Signal Tone.
20. Run a manual steam generator rinse cycle. (See Step 4) This is the final rinse. The
Combi is now ready for normal operation.
27
28
8
33
31
32
57
59
38
37
35
36
39
34
61
26
56
51
53
49
23
52
47
5
63
3
58
50
4
14
2
64
67
20
25
1
46
15
30
39
11
65
66
24
18
27
29
42
40
6
28
60
45
9
41
10
54
16
44
12
55
22
19
21
13
Lamp C5005043
62
7
48
43
17
1010 GAS GENERATOR W CLEANING
Washer Arm C2611068
Light Gasket C6015020
C3216313 B
0706
1010 GAS GENERATOR W CLEANING
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
1
1
1
1
1
1
1
1
1
1
1
C2115483
C2114824
C2115490
C2114452
C2114719
C2114688
C2114743
C2114783
C2115375
C2115443
C6010001
12
13
14
15
16
17
18
19
20
21
C6012001 22
23
24
25
26
27
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C22141901
C2214191
C2614841
C7011002
C2614802
C2013006
C2614740
C26142661
C2614263
C2514352
C2216070
C2608962
C22160801
C2114731
C2114634
111544
28
1
111543
29
1
111542
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
1
4
4
4
4
1
1
1
1
2
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
111540
C8006060
C8005050
C8004057
C6015213
C6015210
C6015206
C6015050
C2114140
C6015021
111541
C6012009
C6012011
C2114817
C6012008
19993
C2017001
C6005427
C6005048
C2414125
109641
C2114287
C5001041
C2114798
C2214143
C2114296
300480
C50180211
58
59
60
61
62
63
64
65
66
67
1
1
1
1
1
1
1
1
1
1
C2215042
C2314882
C2010000
C2614862
C2314900
C2114545
C2115463
C2018000
C2016009
C2216796
ASSEMBLY, PANEL, RIGHT SIDE, 10.10
ASSEMBLY/WELDMENT, INTERMEDIATE TOP, 6.10/10.10
ASSEMBLY, CORNER, FRONT, RIGHT, 10.10/10.20
WELDMENT, FACE PLATE, LOWER, 6.10/10.10
WELDMENT, REINFORCEMENT, DOOR LATCH, 10.10/10.20
ASSEMBLY, SLIDE BAR, DISAPPEARING DOOR, 6.10/10.10
ASSEMBLY, PANEL, REAR, ELECTRIC & GAS INJ, 10.10
ASSEMBLY, PANEL, LEFT SIDE, 10.10
WELDMENT, CHANNEL, FRONT, 6.10/10.10
FRONT PIECE, PRE-MOUNTED, 10.10
WHEEL, BLOWER, 350mm OD X 110mm WIDE, TYPE 304
6.20 & 10.10 COMBI
PAN RACK,LEFT, ELECTROPOLISHED, 10.10
WELDMENT, PAN RACK, RIGHT, 10.10
CAVITY LIGHT
DOOR SEAL, 10.10
ASSEMBLY, SLIDING PLATE VST 10.10/10.20
WELDMENT, HINGE CARRIER, UPPER, DOOR
ASSEMBLY, GUIDE CLIP, VST, COUNTERTOP MODEL
ASSEMBLY, CONTROLLER
ASSEMBLY, CORE TEMPERATURE SENSOR
ASSEMBLY, DOOR 10.10
ASSEMBLED, BLOCK
ASSEMBLY, NEGATIVE PRESSURE SAFETY VENT
ASSEMBLY, HAND SHOWER, 10.10, 6.10
FACEPLATE, UPPER X.10
CORNER, WELDED, REAR, LEFT, 10.10/10.20
WASHER, BELLEVILLE, M10, SMOOTH, TYPE 301 SST,
10.21mm ID X 24mm OD X 1.85mm THICK
RING, RETAINING, EXTERNAL, 1/4", STAINLESS STEEL,
WALDES #5100-25H
WASHER, BELLEVILLE, M8, SERRATED BOTH SIDES, SST,
8.4mm ID X 13mm OD X 0.8mm THICK
NUT, HEX, M10 X 1.5 (DIN 934), STAINLESS STEEL
SCHNORR LOCK WASHER
WASHER, 8.4 A2 DIN 125
NUT, HEX, M8 A4
SPACER, MOTOR 1.299 (FAN DISTANCE 2.008in)
SHIM, WEARING MOTOR SHAFT SEAL
BUSHING, LABYRINTH
SPRING, MOTOR SHAFT SEAL
MOTOR MOUNTING PLATE
SEALING RING, MOTOR SHAFT, VITON, COMBI
NUT, HEX, LEFT-HAND, M8 X 1.25 (DIN 934L), STAINLESS STEEL
GUIDE STRIP, LOWER VST
DOORSTOPPER VA VST
COVER PANEL VST 10.10/10.20
SUPPORT STRIP RST
SWITCH, ROCKER, DPDT, ON/OFF 15A, 125V
SAFETY RAIL VST 6.10/10.10
DIAPHRAGM GROMMET ø 83 (DG60) FOR VAC. REG. VALVE
DIAPHRAGM GROMMET ø 60 mm (DG 48)
FINAL ASSEMBLY, CONDENSER
PORT ASSY, DESCALER
ASSEMBLY, AIR OUTLET
SAFETY TEMPERATURE LIMITER, 340ºC
BRACKET, HIGH LIMIT, STEAM GENERATOR
ASSEMBLY, INTAKE PANEL, GEN, 10.10,
ASSY, CONTROL PANEL, STEAM GEN, WITH PICTO
ASSY., COMP. PANEL, OGB 6.20/10.10
MOTOR W/STUD, ALL VOLTAGES, 3-PHASE, 4 POLE, 0.6KW,
GAS COMBI
WELDMENT, INNER HOUSING, GAS, GEN, 10.10, REI
STEAM GENERATOR, GAS, 10.10, PREASSEMBLED
WELDMENT, HEAT EXCHANGER, GAS, 10.10/20.10
BURNER INSERT,10.10/20.10, HOT AIR, NAT GAS
ASSEMBLY, BURNER INSERT, GEN, GAS, 6.20/10.10, NAT
BASE, GAS, GEN, 10.10 W/CLEANING
ASSEMBLY, PANEL, TOP, GAS GEN, 10.10
DRIP TRAY, 10.10
COVER, BYPASS
ASSEMBLY, COVER, DEHUMIDIFYING GUTTER
29
C3216313 B
0706
8
36
34
7
35
53
41
40
38
39
42
30
28
37
58
12
51
26
50
52
54
62
55
59
5
17
4
23
28
3
33
27
18
42
11
60
61
1
2
21
30
32
49
45
43
31
57
48
9
44
6
10
16
13
19
47
14
15
25
22
24
46
20
1010 GAS INJ W CLEANING
Washer Arm C2611068
Light Gasket C6015020
Lamp C5005043
C3216313 B
0706
1010 GAS INJ W CLEANING
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
1
1
1
1
1
1
1
1
1
1
1
C2115483
C2114824
C2115490
C2114452
C2114719
C2114688
C2114743
C2114783
C2115375
C2115443
C6010001
12
13
14
15
16
17
18
19
20
21
22
23
24
C6012001 25
26
27
28
29
30
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C2114292
C22141901
C2214191
C2114296-3
C2214153
C2614841
C7011002
C2614802
C2013006
C2614740
C26142661
C2614263
C2514352
C2216070
C2608962
C22160801
C2114731
C2114634
111544
31
1
111543
32
1
111542
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
1
4
4
4
4
1
1
1
1
2
1
1
4
1
1
1
1
1
1
1
1
111540
C8006060
C8005050
C8004057
C6015213
C6015210
C6015206
C6015050
C2114140
C6015021
111541
C6012009
C6012011
C2114817
C6012008
19993
C2017001
C6005427
C6005048
C2414125
C50180211
54
55
56
57
58
59
60
61
62
1
1
1
1
1
1
1
1
1
C2114535
C2215041
C2614862
C2010000
300488
C2115453
C2018000
C2016009
C2216796
ASSEMBLY, PANEL, RIGHT SIDE, 10.10
ASSEMBLY/WELDMENT, INTERMEDIATE TOP, 6.10/10.10
ASSEMBLY, CORNER, FRONT, RIGHT, 10.10/10.20
WELDMENT, FACE PLATE, LOWER, 6.10/10.10
WELDMENT, REINFORCEMENT, DOOR LATCH, 10.10/10.20
ASSEMBLY, SLIDE BAR, DISAPPEARING DOOR, 6.10/10.10
ASSEMBLY, PANEL, REAR, ELECTRIC & GAS INJ, 10.10
ASSEMBLY, PANEL, LEFT SIDE, 10.10
WELDMENT, CHANNEL, FRONT, 6.10/10.10
FRONT PIECE, PRE-MOUNTED, 10.10
WHEEL, BLOWER, 350mm OD X 110mm WIDE, TYPE 304 SST,
6.20 & 10.10 COMBI
AIR OUTLET CONECTING PIECE 20.20 GEN. 6.20/10.10/20.20 INJ.
PAN RACK,LEFT, ELECTROPOLISHED, 10.10
WELDMENT, PAN RACK, RIGHT, 10.10
ASSY, CONTROL PANEL, SPRITZER, WITH PICTO
ASSEMBLY, INTAKE PANEL INJ 10.10
CAVITY LIGHT
DOOR SEAL, 10.10
ASSEMBLY, SLIDING PLATE VST 10.10/10.20
WELDMENT, HINGE CARRIER, UPPER, DOOR
ASSEMBLY, GUIDE CLIP, VST, COUNTERTOP MODEL
ASSEMBLY, CONTROLLER
ASSEMBLY, CORE TEMPERATURE SENSOR
ASSEMBLY, DOOR 10.10
ASSEMBLED, BLOCK
ASSEMBLY, NEGATIVE PRESSURE SAFETY VENT
ASSEMBLY, HAND SHOWER, 10.10, 6.10
FACEPLATE, UPPER X.10
CORNER, WELDED, REAR, LEFT, 10.10/10.20
WASHER, BELLEVILLE, M10, SMOOTH, TYPE 301 SST,
10.21mm ID X 24mm OD X 1.85mm THICK
RING, RETAINING, EXTERNAL, 1/4", STAINLESS STEEL,
WALDES #5100-25H
WASHER, BELLEVILLE, M8, SERRATED BOTH SIDES, SST,
8.4mm ID X 13mm OD X 0.8mm THICK
NUT, HEX, M10 X 1.5 (DIN 934), STAINLESS STEEL
SCHNORR LOCK WASHER
WASHER, 8.4 A2 DIN 125
NUT, HEX, M8 A4
SPACER, MOTOR 1.299 (FAN DISTANCE 2.008in)
SHIM, WEARING MOTOR SHAFT SEAL
BUSHING, LABYRINTH
SPRING, MOTOR SHAFT SEAL
MOTOR MOUNTING PLATE
SEALING RING, MOTOR SHAFT, VITON, COMBI
NUT, HEX, LEFT-HAND, M8 X 1.25 (DIN 934L), STAINLESS STEEL
GUIDE STRIP, LOWER VST
DOORSTOPPER VA VST
COVER PANEL VST 10.10/10.20
SUPPORT STRIP RST
SWITCH, ROCKER, DPDT, ON/OFF 15A, 125V
SAFETY RAIL VST 6.10/10.10
DIAPHRAGM GROMMET ø 83 (DG60) FOR VAC. REG. VALVE
DIAPHRAGM GROMMET ø 60 mm (DG 48)
FINAL ASSEMBLY, CONDENSER
MOTOR W/STUD, ALL VOLTAGES, 3-PHASE, 4 POLE, 0.6KW,
GAS COMBI
BASE, GAS, INJ, 10.10 W/CLEANING
WELDMENT, INNER HOUSING, GAS, INJ, 10.10, REI
BURNER INSERT,10.10/20.10, HOT AIR, NAT GAS
WELDMENT, HEAT EXCHANGER, GAS, 10.10/20.10
ASSY., COMP. PANEL, OGS 6.20/10.10
ASSEMBLY, TOP PANEL, GAS INJ, 10.10
DRIP TRAY, 10.10
COVER, BYPASS
ASSEMBLY, COVER, DEHUMIDIFYING GUTTER
31
C3216313 B
0706
620 GAS GEN W CLEANING
Washer Arm C2611068
Set of racks with center support
FK1119821
Light Gasket C6015020
18
62
31
49
13
14
3
22
63 46
19
23
61
65
30 32
50
6
53
57
40
38
39
51
44
41
46
43
24
42
55
45
58
47
56
20
48
22
59
60
54
17
4
1
15
2
26
28
21
5
37
36
33
35
34
27
52
64
10
11
12
25 8
16
9
7
29
Lamp C5005043
32
C3216313 B
0706
620 GAS GEN W CLEANING
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
11
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
33
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
C2115482
C2114826
C2115489
C2114453
C2114690
C2114782
C2514351
C2614801
C2013006
C2115442
C22141881
C22141891
C7011004
C2216080
C2614740
C6012001
C2614841
C26142661
C2614263
C2414125
C6010001
C2608962
C2114732
C2114633
C6012008
C2017000
C6012009
C6012011
C2114816
C2114798
C5001041
111544
34
35
1
1
111543
111542
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
1
1
4
4
4
1
1
1
1
4
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
111541
111540
C8006060
C8005050
C8004057
C6015210
C6015206
C6015050
C2114140
C6015213
C6015021
C6005048
C6005427
C2018001
C50180211
C2614860
C2010032
C2114742
C2115462
300480
C2114287
C2314900
C2314881
109641
C2215026
C21145471
C2114296
C2016009
C2214142
C2114718
ASSEMBLY, PANEL, RIGHT SIDE, 6.20
ASSEMBLY/WELDMENT, INTERMEDIATE TOP, 6.20/10.20
ASSEMBLY, CORNER, FRONT, RIGHT, 6.20
WELDMENT, FACEPLATE, LOWER, 6.20/10.20
ASSEMBLY, SLIDE BAR, DISAPPEARING DOOR, X.20
ASSEMBLY, PANEL, LEFT SIDE, 6.20
DOOR 6.20 COMPLETE
SLIDING PLATE VST 6.20 COMPLETE
WELDMENT, HINGE CARRIER, UPPER, DOOR
ASSEMBLY, CORNER, FRONT LEFT, 6.20
PAN RACKS,LEFT, ELECTROPOLISHED, 6.20
PAN RACKS,RIGHT, ELECTROPOLISHED, 6.20
DOOR SEAL, 6.20
ASSEMBLY, HAND SHOWER
ASSEMBLY, GUIDE CLIP, VST, COUNTERTOP MODEL
ASSEMBLY, BLOCK
CAVITY LIGHT
ASSEMBLY, CONTROLLER
ASSEMBLY, CORE TEMPERATURE SENSOR
FINAL ASSEMBLY, CONDENSER
WHEEL, BLOWER, 350mm OD X 110mm WIDE, TYPE 304 SST, 6.20 & 10.10 COMBI
ASSEMBLY, NEGATIVE PRESSURE SAFETY VENT
FACEPLATE, UPPER X.20
CORNER, WELDED, REAR, LEFT, 6.20
SUPPORT STRIP RST
SAFETY RAIL, VST, X.20
GUIDE STRIP, LOWER VST
DOORSTOPPER VA VST
COVER PANEL, DISAPPEARING DOOR RST 6.20
BRACKET, HIGH LIMIT, STEAM GENERATOR
SAFETY TEMPERATURE LIMITER, 340ºC
WASHER, BELLEVILLE, M10, SMOOTH, TYPE 301 SST,
10.21mm ID X 24mm OD X 1.85mm THICK
RING, RETAINING, EXTERNAL, 1/4", STAINLESS STEEL, WALDES #5100-25H
WASHER, BELLEVILLE, M8, SERRATED BOTH SIDES, SST,
8 x4mm ID X 13mm OD X 0.8mm THICK
NUT, HEX, LEFT-HAND, M8 X 1.25 (DIN 934L), STAINLESS STEEL
NUT, HEX, M10 X 1.5 (DIN 934), STAINLESS STEEL
SCHNORR LOCK WASHER
WASHER, 8.4 A2 DIN 125
NUT, HEX, M8 A4
SHIM, WEARING MOTOR SHAFT SEAL
BUSHING, LABYRINTH
SPRING, MOTOR SHAFT SEAL
MOTOR MOUNTING PLATE
SPACER, MOTOR 1.299 (FAN DISTANCE 2.008in)
SEALING RING, MOTOR SHAFT, VITON, COMBI
DIAPHRAGM GROMMET ø 60 mm (DG 48)
DIAPHRAGM GROMMET ø 83 (DG60) FOR VAC. REG. VALVE
DRIP TRAY, DOOR
MOTOR W/STUD, ALL VOLTAGES, 3-PHASE, 4 POLE, 0.6KW, GAS COMBI
BURNER INSERT, 6.20, AIR, COMPLETE, NAT GAS
HEAT EXCHANGER 6.20 WELDED
ASSEMBLY, PANEL, REAR, ELECTRIC & GAS INJ, 6.20
ASSEMBLY, TOP PANEL, GAS GEN, 6.20
ASSY., COMP. PANEL, OGB 6.20/10.10
ASSEMBLY, AIR OUTLET,
ASSEMBLY, BURNER INSERT, GEN, GAS, 6.20/10.10, NAT
ASSEMBLY, STEAM GENERATOR, GAS 6.20
PORT ASSY, DESCALER
ASSEMBLY, INNER HOUSING, 6.20, GAS, STEAM GEN, REI, KTM
BASE, 6.20 GAS GEN, W/CLEAN
ASSY, CONTROL PANEL, STEAM GEN, WITH PICTO
COVER, BYPASS
INTAKE PANEL STEAM GENERATOR 6.20, COMPLETE
ASSEMBLY, REINFORCEMENT, DOOR LATCH, 6.20
33
C3216313 B
0706
620 GAS INJ W CLEANING
Washer Arm C2611068
Set of racks with center support
FK1119821
Light gasket C6015020
18
52
20
33
51
15
4
16
3
22
61 48
21
25
28
32 34
56
34
7
42
40
41
6
57
46
43
48
45
26
44
54
47
49
60
22
50
24
55
59
62
19
1
2
17
30
23
5
39
38
35
37
36
29
58
53
12
13
14
27 10 11
9
31
Lamp C5005043
C3216313 B
0706
620 GAS INJ W CLEANING
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
C2115482
C2114826
C2115489
C2114453
C2114690
C2114742
C2114782
C2115452
C2514351
C2614801
C2013006
C2115442
C22141881
C22141891
C7011004
C2216080
C2614740
C6012001
C2614841
C26142661
C2614263
C2414125
C6010001
C2608962
C2114732
C2114633
C6012008
C2017000
C6012009
C6012011
C2114816
C2114798
19993
C5001041
111544
36
37
1
1
111543
111542
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
1
1
4
4
4
1
1
1
1
4
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
111541
111540
C8006060
C8005050
C8004057
C6015210
C6015206
C6015050
C2114140
C6015213
C6015021
C6005048
C6005427
C2018001
C2114296-3
C2214152
300488
C2215025
C50180211
C2614860
C2010032
C2114537
C2114292
C2016009
C2114718
ASSEMBLY, PANEL, RIGHT SIDE, 6.20
ASSEMBLY/WELDMENT, INTERMEDIATE TOP, 6.20/10.20
ASSEMBLY, CORNER, FRONT, RIGHT, 6.20
WELDMENT, FACEPLATE, LOWER, 6.20/10.20
ASSEMBLY, SLIDE BAR, DISAPPEARING DOOR, X.20
ASSEMBLY, PANEL, REAR, ELECTRIC & GAS INJ, 6.20
ASSEMBLY, PANEL, LEFT SIDE, 6.20
ASSEMBLY, TOP PANEL, GAS INJ, 6.20
DOOR 6.20 COMPLETE
SLIDING PLATE VST 6.20 COMPLETE
WELDMENT, HINGE CARRIER, UPPER, DOOR
ASSEMBLY, CORNER, FRONT LEFT, 6.20
PAN RACKS,LEFT, ELECTROPOLISHED, 6.20
PAN RACKS,RIGHT, ELECTROPOLISHED, 6.20
DOOR SEAL, 6.20,
ASSEMBLY, HAND SHOWER
ASSEMBLY, GUIDE CLIP, VST, COUNTERTOP MODEL
ASSEMBLY, BLOCK
CAVITY LIGHT
ASSEMBLY, CONTROLLER
ASSEMBLY, CORE TEMPERATURE SENSOR
FINAL ASSEMBLY, CONDENSER
WHEEL, BLOWER, 350mm OD X 110mm WIDE, TYPE 304 SST, 6.20 & 10.10 COMBI
ASSEMBLY, NEGATIVE PRESSURE SAFETY VENT
FACEPLATE, UPPER X.20
CORNER, WELDED, REAR, LEFT, 6.20
SUPPORT STRIP RST
SAFETY RAIL, VST, X.20
GUIDE STRIP, LOWER VST
DOORSTOPPER VA VST
COVER PANEL, DISAPPEARING DOOR RST 6.20
BRACKET, HIGH LIMIT, STEAM GENERATOR
SWITCH, ROCKER, DPDT, ON/OFF 15A, 125V
SAFETY TEMPERATURE LIMITER, 340ºC
WASHER, BELLEVILLE, M10, SMOOTH, TYPE 301 SST,
10.21mm ID X 24mm OD X 1.85mm THICK
RING, RETAINING, EXTERNAL, 1/4", STAINLESS STEEL, WALDES #5100-25H
WASHER, BELLEVILLE, M8, SERRATED BOTH SIDES, SST,
8.4mm ID X 13mm OD X 0.8mm THICK
NUT, HEX, LEFT-HAND, M8 X 1.25 (DIN 934L), STAINLESS STEEL
NUT, HEX, M10 X 1.5 (DIN 934), STAINLESS STEEL
SCHNORR LOCK WASHER
WASHER, 8.4 A2 DIN 125
NUT, HEX, M8 A4
SHIM, WEARING MOTOR SHAFT SEAL
BUSHING, LABYRINTH
SPRING, MOTOR SHAFT SEAL
MOTOR MOUNTING PLATE
SPACER, MOTOR 1.299 (FAN DISTANCE 2.008in)
SEALING RING, MOTOR SHAFT, VITON, COMBI
DIAPHRAGM GROMMET ø 60 mm (DG 48) P2
DIAPHRAGM GROMMET ø 83 (DG60) FOR VAC. REG. VALVE
DRIP TRAY, DOOR
ASSY, CONTROL PANEL, SPRITZER, WITH PICTO
ASSEMBLY, INTAKE PLATE, IN, 6.20
ASSY., COMP. PANEL, OGS 6.20/10.10
ASSEMBLY, INNER SHELL 6.20, GAS, IN, REI, KTM
MOTOR W/STUD, ALL VOLTAGES, 3-PHASE, 4 POLE, 0.6KW, GAS COMBI
BURNER INSERT, 6.20, AIR, COMPLETE, NAT GAS
HEAT EXCHANGER 6.20 WELDED
BASE, GAS, INJ, 6.20, W/ CLEANING
AIR OUTLET CONECTING PIECE 20.20 GEN. 6.20/10.10/20.20INJ.
COVER, BYPASS
ASSEMBLY, REINFORCEMENT, DOOR LATCH, 6.20
35
C3216313 B
0706
36
24
19
26
25
16
19
27
33
8
38
40
2
7
4
18
41
17
43
44
5
18
17
42
6
48
3
35
19
16
18
16
11
29
48
1
9
12
28
45
49
10
30
12
36
40
1
14
3
49
15
33
19
33
14
37
13
32
20
12
15
19
21
22
19
34
21
22
23
COMPONENT PANEL ASSEMBLY, Gas
OGB 6.20 & 10.10 MODELS
300480 C
0706
COMPONENT PANEL ASSEMBLY, GAS
OGB 6.20 & 10.10 MODELS
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
32
33
34
35
36
37
38
40
41
42
43
44
45
2
1
2
1
1
1
4
1
5
4
3
3
1
5
2
14
6
14
6
2
8
2
1
1
1
1
1
1
1
1
5
14
10
6
4
2
1
6
2
4
4
4
1
300419
111603
111601
111526
300412
300413
C8009043
C5116110
C4014012
C4014006
C4014037
C4014011
300350
C4014030
C4014031
C8001024
111605
111606
C4014000
C4014013
C4014010
C4014009
C4014008
C4014024
C4014016
C4014023
C4014020
300418
300416
KE52936-9
C4014033
C4014044
C4014032
C4014039
C4014001
C4014002
C5115400
106123
20323
C8003095
C8004030
C8006030
C700106606000
TRANSFORMER, 24V
DIN RAIL 3.25"
DIN RAIL 8.375"
PLATE, ADAPTER, A.C. DRIVE
AC DRIVE (6.20-10.10)
LINE FILTER, 10A
M4 HEX STAND OFF, 70 MM
BRACKET, TERMINAL BLOCK, COMPONENT PANEL
TERMINAL BLOCK, SPRING-LOADED, FOUR-WIRE, BLUE
TERMINAL BLOCK, CONDUCTOR, SPRING-LOADED
DINRAIL MOUNTED FUSEHOLDER (6.3X32)
COVER, FOUR-WIRE
POWER SUPPLY (12V)
TERMINAL BLOCK, SPRING LOADED, 1.5MM2
COVER 2.5 MM2
SCREW, FILISTER HD, M4x10 DIN 7985
M4 NUT
M4 LOCK WASHER
SNAP-ON END BRACKET
TERMINAL BLOCK, SPRING- LOADED, FOUR-WIRE
TERMINAL, SPRING LOADED, FOUR WIRE, 2.5 MM2
TERMINAL BLOCK, SPRING LOADED, 1.5 MM2, BLUE
COVER FOUR-WIRE 2.5 MM2
TERMINAL, FEED THROUGH, 4 MM2
TERMINAL, GROUNDED, SPRING LOADED, 2.5 MM2
TERMINAL, FEED THROUGH,4MM2, BLUE
COVER 4 MM2
FUSE MDA-1
FUSE MDA-2
FUSE, MDA-15
LABEL BLANK, TERMINAL BLOCK, ZB4
LABEL, BLANK, TERMINAL BLOCK, ZB6
SERRATED COVER STRIP,PLAIN ZB5
LABEL BLANK, TERMINAL BLOCK, ZBF6
JUMPER, 2 PIN
JUMPER 2-PIN
PANEL, ELECTRICAL COMPONENT 6.10/6.20/10.10
SCREW, 10-32 X 1/2, TORX/ PAN HD, THRD FORMING, ZN
RING TO MALE TAB TERMINAL
HEXAGON BOLT, M5x16, A2 HUD 20.20
HEXAGON NUT, M5
RING, SPRING RETAINER, B5, A2
EDGE GUARD
46
47
48
49
57
58
1
1
4
4
2
4
300483
300501
20370
300231
111751
106127
WIRE HARNESS, 6.20/10.10
WIRE HARNESS, POWER, OGB/OGS 6.20/10.10
TERM., FULL INSUL, MALE, 0.250 TAB
TERM., FULL INSUL, FEMALE, 0.250 TAB
BUSHING, UNIVERSAL,1.5DIA HOLE,HEYCO#2213,SNAP-IN UL
SCREW, 6-32 X 1/2, TORX/PAN HD
37
300480 C
0706
24
19
26
25
38
16
19
27
33
8
40
38
2
7
4
18
41
17
39
31
43
44
5
18
17
42
6
48
18
16
16
35
19
3
11
29
18
17
9
12
28
45
1
10
30
39
12
3
14
33
40
49
15
36
19
14
33
13
33
32
20
12
15
37
19
21
22
19
34
21
22
23
COMPONENT PANEL ASSEMBLY, GAS
OGS 6.20 & 10.10 MODELS
300488 C
0706
COMPONENT PANEL ASSEMBLY, GAS
OGS 6.20 & 10.10 MODELS
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
1
1
2
1
1
1
4
1
5
4
3
3
1
5
2
10
8
12
6
2
8
2
1
1
1
1
1
1
1
1
2
5
14
10
6
4
2
1
6
6
2
4
4
4
1
1
1
2
2
300419
111603
111601
111526
300412
300413
C8009043
C5116110
C4014012
C4014006
C4014037
C4014011
300350
C4014030
C4014031
C8001024
111605
111606
C4014000
C4014013
C4014010
C4014009
C4014008
C4014024
C4014016
C4014023
C4014020
300418
300416
KE52936-9
111751
C4014033
C4014044
C4014032
C4014039
C4014001
C4014002
C5115400
C8001022
106123
20323
C8003095
C8004030
C8006030
C700106606000
300490
300501
20370
300231
TRANSFORMER, 24V
DIN RAIL 3.25"
DIN RAIL 8.375"
PLATE, ADAPTER, A.C. DRIVE (NOT SHOWN)
AC DRIVE (6.20-10.10) (NOT SHOWN)
LINE FILTER, 10A
M4 HEX STAND OFF, 70 MM
BRACKET, TERMINAL BLOCK, COMPONENT
TERMINAL BLOCK, SPRING-LOADED, FOUR-WIRE, BLUE
TERMINAL BLOCK, CONDUCTOR, SPRING-LOADED
DINRAIL MOUNTED FUSEHOLDER (6.3X32)
COVER, FOUR-WIRE
POWER SUPPLY (12V)
TERMINAL BLOCK, SPRING LOADED, 1.5MM2
COVER 2.5 MM2
SCREW, FILISTER HD, M4x10 DIN 7985
M4 NUT
M4 LOCK WASHER
SNAP-ON END BRACKET
TERMINAL BLOCK, SPRING- LOADED, FOUR-WIRE
TERMINAL, SPRING LOADED, FOUR WIRE, 2.5
TERMINAL BLOCK, SPRING LOADED, 1.5 MM2,
COVER FOUR-WIRE 2.5 MM2
TERMINAL, FEED THROUGH, 4 MM2
TERMINAL, GROUNDED, SPRING LOADED, 2.5 MM2
TERMINAL, FEED THROUGH,4MM2, BLUE
COVER 4 MM2
FUSE MDA-1
FUSE MDA-2
FUSE, MDA-15
BUSHING, UNIVERSAL,1.5DIA HOLE,HEYCO# 2213, SNAP-IN UL
LABEL BLANK, TERMINAL BLOCK, ZB4
LABEL, BLANK, TERMINAL BLOCK, ZB6
SERRATED COVER STRIP,PLAIN ZB5
LABEL BLANK, TERMINAL BLOCK, ZBF6
JUMPER, 2 PIN
JUMPER 2-PIN
PANEL, ELECTRICAL COMPONENT 6.10/6.20/10.10
STUD, WELD, M4 X 6, CD, SST
SCREW, 10-32 X 1/2, TORX/ PAN HD, THRD FORMING, ZN
RING TO MALE TAB TERMINAL
HEXAGON BOLT, M5x16, A2 HUD 20.20
HEXAGON NUT, M5
RING, SPRING RETAINER, B5, A2
EDGE GUARD
WIRE HARNESS,OGS, 6.20/10.10
WIRE HARNESS, POWER, OGB/OGS 6.20/10.10
TERM.,FULL INSUL, MALE, 0.250 TAB
TERM., FULL INSUL, FEMALE, 0.250 TAB
39
300488 C
0706
ASSEMBLY, CONTROL PANEL, WITH PICTO
ALL MODELS
2
5
4
11
10
9
1
7
6
3
8
ITEM QTY
1
2
3
4
5
6
7
8
9
10
11
12
1
1
1
1
1
10
1
10
1
1
2
2
1
PART N0.
DESCRIPTION
C2114297
C5019101
C5019105
C5009313
C5009314
C8009030
C7011010
C6005254
111588
111590
C6005270
C8007013
300533
WELDMENT, CONTROL PANEL
CONTROLLER, 5010 OPERATING MODULE
CONTROLLER, 5010 PICTOMODULE PICTO
LATCH ROCKER
KNOB, SELECTOR, COMBI
SPACER, CONTROL PANEL
GASKET, FRONT PLATE
NUT, KNURLED
LABEL, CONTROL PANEL, STEAM GEN, WITH PICTO
LABEL, CONTROL PANEL, SPRITZER, WITH PICTO
SPACER, CONTROL KNOB STOP
SLOTTED PAN-HEAD TAPPING SCREW 2.2 X 13
CABLE, CONNECTING, CONTROL (NOT SHOWN)
40
C2114296 B & C2114296-3 B
0706
BASE, GAS,
INJECTOR,
WITH CLEANING
OGS 10.10 MODELS
19
2
18
17
9
8
Pressure Switch C5009055
Agent Pump 300352
15 22
4
15
1
12
6
1
14
10
3
20
11
5
13
ITEM
QTY
PART N0.
DESCRIPTION
32
31
30
22
20
19
18
17
16
15
14
13
12
11
10
9
8
6
5
4
3
2
1
1
1
1
1
1
1
1
1
1
5
7
3
1
1
2
1
1
4
5
1
1
1
1
C5016002
C700106607000-1
C700106607000
C2010066
C5016001
C2016147
C2016130
C2616452
C5215897
C8005021
C8013004
C8003029
111551
111522
111538
C6005021
C70016603000
C8003035
C8006058
C5011003
C2216088
C2114699
C2114520
LOCKNUT M25
EDGE PROTECTOR, CUT 7.000"
EDGE PROTECTOR, CUT 7.000"
CONNECTION, GAS, SINGLE 3/4"
FITTING, ELECTRICAL, LIQUID TIGHT
CONDENSER HOSE ASSY, GAS
ASSY, WATER VALVE, GAS, 10.10
BOTTOM FLAP, PUMP HOUSING GAS 10.10 110V PREASSEMBLED (NOT SHOWN)
CABLE HARNESS, ILLUMINATION
WASHER, 4.3, DIN 125
HEXAGON BOLT M4 X 10
MLF, SCREW, M5x10
TRAY, DRIP, FAN, REAR, ELECTRIC & GAS INJ, 6.10/10.10
TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10
ADAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH
RUBBER BUSHING 42 MM OD
EDGE PROTECTOR, CUT 3.000"
HEXAGON BOLT M5X10
SCHNORR LOCK WASHER
CONNECTION FLANGE
AIR INLET BOX FINAL ASSEMBLY
ASSEMBLY, TOP COVER, PUMP HOUSING, AUTO CLEAN SYSTEM
OUTER BASE, EL, 6.10/10.10
41
C2114535 A
0706
BASE, GAS,
INJECTOR,
NO CLEANING
OGS 10.10 MODELS
16
20
19
8
21
7
3
14
14
1
11
5
1
13
4
17
9
2
5
10
4
12
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
19
20
21
32
33
34
1
1
1
5
4
1
1
2
1
1
3
7
5
1
1
1
1
1
1
1
1
1
C2114520
C2216088
C5011003
C8006058
C8003035
C70016603000
C6005021
111538
111522
111551
C8003029
C8013004
C8005021
C5215897
C2016147
C5016001
C2016131
C2114626
C2010066
C700106607000
C700106607000-1
C5016002
OUTER BASE, EL, 6.10/10.10
AIR INLET BOX FINAL ASSEMBLY
CONNECTION FLANGE
SCHNORR LOCK WASHER
HEXAGON BOLT M5X10
EDGE PROTECTOR, CUT 3.000
RUBBER BUSHING 42 MM OD"
ADAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH
TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10
TRAY, DRIP, FAN, REAR, ELECTRIC & GAS INJ, 6.10/10.10
MLF, SCREW, M5x10
HEXAGON BOLT M4 X 10
WASHER, 4.3, DIN 125
CABLE HARNESS, ILLUMINATION
CONDENSER HOSE ASSY, GAS
FITTING, ELECTRICAL, LIQUID TIGHT
ASSEMBLY, WATER VALVE, ELECTRIC INJECTOR, 6.20
COVER, BOTTOM, PUMP HOUSING
CONNECTION, GAS, SINGLE 3/4"
EDGE PROTECTOR, CUT 7.000"
EDGE PROTECTOR, CUT 7.000"
LOCKNUT M25
42
C21145351 A
0706
BASE, GAS,
GENERATOR,
WITH CLEANING
OGB 6.20 MODELS
2
19
4
7
13
27
3
8
A
5
15
DETAIL A
1
15
Pressure Switch C5009055
Agent Pump 300352
18
16
16
22
10
12
12
17
10
20
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
7
8
10
11
12
13
15
16
17
18
19
20
21
22
23
27
28
29
30
1
1
1
1
1
1
1
5
2
1
1
5
7
1
1
1
3
1
2
1
1
1
1
1
C2114542
C2114699
C2616451
C2016147
C2010068
C2016129
C5011003
C8006058
C8003035
C5016001
C5016002
C8005021
C8013004
111522
111524
C2116092
C8003029
C70016603000
111538
C5215897
111752
C2216090
C700106607000
C700106607000-1
ASSEMBLY, OUTER BASE, GAS, STEAM GEN, 6.20/10.20
ASSEMBLY, TOP COVER, PUMP HOUSING, AUTO CLEAN SYSTEM
BOTTOM FLAP, PUMP HOUSING, GAS, 6.20, 110V
CONDENSER HOSE ASSY, GAS
DOUBLE GAS CONNECTION R 3/4"
ASSEMBLY, WATER VALVE, GAS, 6.20, GEN W / CLEANING SYSTEM
CONNECTION FLANGE
SCHNORR LOCK WASHER
HEXAGON BOLT M5X10
FITTING, ELECTRICAL, LIQUID TIGHT
LOCKNUT, M25,
WASHER, 4.3, DIN 125
HEXAGON BOLT M4 X 10
TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10
TRAY, DRIP, FAN, REAR, 6.20/20.20
BOX, AIR INTAKE
MLF, SCREW, M5x10
EDGE PROTECTOR, CUT 3.000"
ADAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH
CABLE, HARNESS, ILLUMINATION
PLUG, 1.500 DIA, HOLE, SNAP-IN
FAN, AIR INLET BOX ASSEMBLY
EDGE PROTECTOR, CUT 7.000"
EDGE PROTECTOR, CUT 7.000"
43
C21145471 A
0706
2
BASE, GAS,
GENERATOR,
NO CLEANING
OGB 6.20 MODELS
17
16
10
20
18
5
3
12
12
A
1
DETAIL A
15
13
13
21
7
9
8
14
7
19
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
5
7
8
9
10
12
13
14
15
16
17
18
19
20
21
23
29
30
31
32
1
1
1
1
5
2
1
1
5
7
1
1
1
1
1
3
1
2
1
1
1
1
1
C2114542
C2016147
C2010068
C5011003
C8006058
C8003035
C5016001
C5016002
C8005021
C8013004
111522
111524
C2116092
C2016126
C2114626
C8003029
C70016603000
111538 A
C5215897
C2216090
111752
C700106607000
C700106607000-1
ASSEMBLY, OUTER BASE, GAS, STEAM GEN, 6.20/10.20
CONDENSER HOSE ASSY, GAS
DOUBLE GAS CONNECTION R 3/4"
CONNECTION FLANGE
SCHNORR LOCK WASHER
HEXAGON BOLT M5X10
FITTING, ELECTRICAL, LIQUID TIGHT
LOCKNUT, M25
WASHER, 4.3, DIN 125
HEXAGON BOLT M4 X 10
TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10
TRAY, DRIP, FAN, REAR, 6.20/20.20
BOX, AIR INTAKE
ASSY, WATER VALVE, GAS, 6.20
COVER, BOTTOM, PUMP HOUSING
MLF, SCREW, M5x10
EDGE PROTECTOR, CUT 3.000"
DAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH
CABLE, HARNESS, ILLUMINATION
FAN, AIR INLET BOX ASSEMBLY
PLUG, 1.500 DIA, HOLE, SNAP-IN
EDGE PROTECTOR, CUT 7.000"
EDGE PROTECTOR, CUT 7.000"
44
C21145472 A
0706
BASE, GAS,
INJECTOR,
WITH CLEANING
OGS 6.20 MODELS
11
20
3
2
19
22
17
5
A
15
23
15
1
DETAIL A
10
16
Pressure Switch C5009055
Agent Pump 300352
14
14
8
12
21
16
9
12
13
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
5
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
30
31
32
33
1
1
1
1
2
1
1
1
5
3
7
5
4
1
1
1
1
1
1
1
1
1
1
1
C2114522
C2114699
C2016127
C5011003
111538
111522
111524
C2116092
C8006058
C8003029
C8013004
C8005021
C8003035
C70016603000
C5215897
C2616451
C2016147
C5016001
C5016002
C2010066
C2216090
111752
C700106607000-1
C700106607000
ASSEMBLY, OUTER PLATE EL 6.20/10.20
ASSEMBLY, TOP COVER, PUMP HOUSING, AUTO CLEAN SYSTEM
ASSY, WATER VALVE, GAS, 6.20
CONNECTION FLANGE
ADAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH
TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10
TRAY, DRIP, FAN, REAR, 6.20/20.20
BOX, AIR INTAKE
SCHNORR LOCK WASHER
MLF, SCREW, M5x10
HEXAGON BOLT M4 X 10
WASHER, 4.3, DIN 125
HEXAGON BOLT M5X10
EDGE PROTECTOR, CUT 3.000"
CABLE HARNESS, ILLUMINATION
BOTTOM FLAP, PUMP HOUSING, GAS, 6.20, 110V
CONDENSER HOSE ASSY, GAS
FITTING, ELECTRICAL, LIQUID TIGHT
LOCKNUT, M25 (NOT SHOWN)
CONNECTION, GAS, SINGLE 3/4"
FAN, AIR INLET BOX ASSEMBLY
PLUG, 1.500 DIA, HOLE, SNAP-IN
EDGE PROTECTOR, CUT 7.000"
EDGE PROTECTOR, CUT 7.000"
45
C2114537 A
0706
ASSEMBLY, WATER HOSE SYSTEM, CONDENSER
ALL MODELS
Connecter Flange C5011003
1
3
5
4
2
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
1
2
1
1
1
2
C6015215
111647
11149811000
300455
300407
300509
ELBOW, HOSE CONNECTION, 3/8" WITH SEAL
CLAMP, OETIKER, S/S, 19/32"
HOSE, SILICONE, 3/8" ID X 11.000
VALVE ASSEMBLY, 1 WAY, 120 VAC
FILTER, ELECTRICAL
TERMINAL, 18-22 AWG PIGGY BACK
46
C2016147 A
0706
ASSEMBLY, WATER VALVE
ALL GAS 10.10 MODELS
3
3
8
9 11
11 4
3
3
8
6 12
1
5
6 12
3
2
10
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
3
6
4
7
1
2
1
1
1
1
A/R
A/R
300407
300509
111498
111647
C5001085
C6015401
C6015232
C6006140
C5009063
300363
00946
111561
FILTER, ELECTRICAL
TERMINAL, 18-22 AWG PIGGY BACK
HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH)
CLAMP, OETIKER, S/S, 19/32"
PRESSURE REGULATING VALVE ODGAS
BARB, 1/2 R X 3/8 HOSE
CONNECTION NOZZLE 0.6MM 6.20/10.10/10.20
GAUGE, 60 PSI BOTTOM MOUNT
PUSH BUTTON SWITCH, INJ, (CHANGE-OVER CONTACT)
TRIPLE SOLENOID VALVE 110-120V 50/60 Hz 180º
TAPE, TEFLON, 1/2"
SEALANT, LOCTITE, WHITE, DRI-SEAL, 513
47
C2016038 B
0706
ASSEMBLY, WATER VALVE
10.10 MODELS
3
3
8
9 11
11 4
3
3
8
6 12
1
5
6 12
3
2
10
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
3
6
4
7
1
2
1
1
1
1
A/R
A/R
300407
300509
111498
111647
C5001085
C6015401
C6015232
C6006140
C5009063
300363
00946
111561
FILTER, ELECTRICAL
TERMINAL, 18-22 AWG PIGGY BACK
HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH)
CLAMP, OETIKER, S/S, 19/32"
PRESSURE REGULATING VALVE ODGAS
BARB, 1/2 R X 3/8 HOSE
CONNECTION NOZZLE 0.6MM 6.20/10.10/10.20
GAUGE, 60 PSI BOTTOM MOUNT
PUSH BUTTON SWITCH, INJ, (CHANGE-OVER CONTACT)
TRIPLE SOLENOID VALVE 110-120V 50/60 Hz 180º
TAPE, TEFLON, 1/2"
SEALANT, LOCTITE, WHITE, DRI-SEAL, 513
48
C2016130 A
0706
ASSEMBLY, WATER VALVE, INJECTOR, GAS
OGS 6.20 & 10.10 MODELS
2
7
9
2
8 11
11 5
2
12 3
4
2
10
6
12 3
1
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
1
4
2
1
1
6
1
1
2
4
A/R
A/R
300456
111498
C6015401
C5001085
C6006140
111647
C6015232
C5009063
300407
300509
00946
111651
VALVE ASSY. 2 WAY 120VAC
HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH)
BARB, 1/2 R X 3/8 HOSE
PRESSURE REGULATING VALVE OD GAS
GAUGE, 60 PSI BOTTOM MOUNT
CLAMP, OETIKER, S/S, 19/32"
CONNECTION NOZZLE 0.6MM 6.20/10.10/10.20
PUSH BUTTON SWITCH, INJ, (CHANGE-OVER CONTACT)
FILTER, ELECTRICAL
TERMINAL, 18-22 AWG PIGGY BACK
TAPE, TEFLON, 1/2"
SEALANT, LOCTITE, WHITE, DRI-SEAL 513
49
C2016128 A
0706
ASSEMBLY, WATER SUPPLY, GENERATOR W/CLEANING SYSTEM
OEB & OGB 6.20 MODELS
STEAM GENERATOR
2
1
2
CLEANING
2
DEHUMIDIFICATION
2
4
2
CLEANING
ITEM
QTY
PART N0.
DESCRIPTION
1
1
2
3
4
5
6
1
300453
300363
111498
111647
111646
VALVE ASSEMBLY, 3WAY 240VAC
TRIPLE SOLENOID VALVE 110-120V 50/60 Hz 180º
HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH)
CLAMP, OETIKER, S/S, 19/32"
TEE, BRASS, 3/8" BRASS
50
C2016035 A & C2016129 A
0706
ASSEMBLY, WATER VALVE
ALL GAS 6.20 MODELS
2
2
4
5
3
1
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
1
2
2
2
4
300456
111498
111647
300407
300509
VALVE ASSY. 2 WAY 120VAC
HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH)
CLAMP, OETIKER, S/S, 19/32"
FILTER, ELECTRICAL
TERMINAL, 18-22 AWG PIGGY BACK
51
C2016126 A
0706
ASSEMBLY, WATER VALVE
OGS 6.20 MODELS
4
6
5
4
4
9
11
4
4
8
10
2
7
2
8
4
3
1
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
1
3
6
5
10
1
1
2
1
1
1
300363
300407
300509
111498
111647
111646
C5001085
C6015401
C6015232
C6006140
C5009063
TRIPLE SOLENOID VALVE 110-120V 50/60 Hz 180º (OGS 6.20)
FILTER, ELECTRICAL
TERMINAL, 18-22 AWG PIGGY BACK
HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH)
CLAMP, OETIKER, S/S, 19/32"
TEE, BRASS, 3/8" BRASS
PRESSURE REGULATING VALVE ODGAS
BARB, 1/2 R X 3/8 HOSE
CONNECTION NOZZLE 0.6MM 6.20/10.10/10.20
GAUGE, 60 PSI BOTTOM MOUNT
PUSH BUTTON SWITCH, INJ, (CHANGE-OVER CONTACT)
52
C2016127 A
0706
ASSEMBLY, STEAM GENERATOR, GAS
OGB 6.20 MODELS
15
16
2
13
9
17
5
6
5
8
10
1
6
7
11 12
11 12
3
10
7
14
4
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
1
1
1
1
2
1
1
1
1
15
A/R
1
1
2
1
1
11
C2314891
C2314243
C5016006
C2314991
C5019003
C6015023
C2314968
C6005260
C6015040
C2314974
C8017011
C7014000
06240
C6006089
C6005025
C6006092
05231
101953
WELDMENT, GEN GAS 6.20 (NOT SHOWN)
SUPPORT, STEAM GEN, TABLE TOP UNIT
THERMOCOUPLE, SENSOR, OSC/OSP, 64.960" (1650MM)
PUMP, 110V, GAS STEAM GENERATOR
ASSEMBLY, DOUBLE LEVEL PROBE
FLAT GASKET FOR IMMERSION HEATER
INSPECTION FLANGE, STEAM GENERATOR
SEAL, THERMOCOUPLE SENSOR, OSC/OSP
FLAT GASKET FOR DOUBLE-LEVEL PROBE
FLANGE, INSPECTION, STEAM GENERATOR
NUT, FLANGE, HEX
COPPER PASTE
FTG, HOSE BARB, 3/4 X 3/4 MPT
HOSE CLAMP, 40-60 MM
FLAT GASKET, 1.673 x 2.126 x 0.079 in.
HEXAGON NUT R 1 1/4"
ELBOW, STREET 90 X 3/4 NPT, BRASS
CLIP, INSULATION RETAINER, 1-1/2, .105 HOLE, GALV.
53
C2314881 D
0706
PUMP, STEAM GENERATOR, GAS, 110V
ALL GAS MODELS
4
4
5
7
2
6
3
1
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
1
1
1
1
1
4
4
C6015100
C6005299
C8009057
300506
111630
111633
C8017008
DRAIN ELBOW FOR STEAM GENERATOR
SUPPORT BUSHING, STEAM GENERATOR - PUMP
WIRE CLAMP D: 36, BLACK
DRAIN PUMP WITH 110 V MOTOR
BRACKET, PUMP, GAS GEN
SCREW, HEX HD, M3 x 16, SST, FULLY THREADED
NUT, LOCKING, SERRATED
54
C2314991 C
0706
ASSEMBLY, BURNER INSERT, STEAM GENERATOR, NAT GAS
OGB 6.20 & 10.10 MODELS
21
23
9
22
10
12
26
26
13
20 25
14
24
18
16
18
3
11
17
6
10
8
26
1
2
15
27 28
19
7
20
8
25
21
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
2
5
A/R
1
1
1
1
8
6
1
1
C2010045
C6015032
C2615351
C2010014
C2614907
C4018000
C4018002
C6015037
C5018006
C6015034
C6016000
C6016009
C6017009
C6016030
C2615367
C5015004
C2614845
C6015039
C8012001
C7014000
C6016023
C6016025
C2616516
111595
C8017010
C8017008
300484
20351
BURNER INSERT GEN STEAM 6.10/6.20/10.10 WELDED
SEAL, BURNER ø 50 MM
RESTRICTION FLANGE ø 210 RG128
BURNER, ø 50 x150, 20 KW
CLAMPING FLANGE, STEAM GENERATOR, BURNER, ø 50
MONITORING ELECTRODE
AUTO-IGNITION ELECTRODE
SEAL, ELECTRODE
BURNER BLOWER, RG128, 110V
SEAL, FAN RG128/148
VENTURI 40 KW
GAS VALVE, HONEYWELL, 110V
ORIFICE, ø 05.65 NAT GAS
SEALING RING, GAS SCREEN
FLANGE, BURNER
INSPECTION GLASS, BURNER
COVER, INSPECTION GLASS, BURNER
SEAL, INSPECTION GLASS, BURNER
SCREW, M5x12, FILLISTER HD, TORX
COPPER PASTE
AUTOMATIC FIRING DEVICE, 110V, AUTO-IGNITION
COVER, AUTOMATIC FIRING DEVICE
GAS HOSE, 580 LG, PREASSEMBLED
GASKET, CORK, BURNER VENTURI, COMBI
FLANGE NUT
NUT, LOCKING, SERRATED
TERM, PUSHON, .110, 22-16AWG SEMI INSUL.
TERM, SLIPON FULL INSUL .032X.25 TAB 22-18AWG
55
4
5
C2314900 B
0706
BURNER INSERT, HL, PRE-MOUNTED
ALL GAS MODELS
19 20
18
2
3
7
9
6
8
18
5
1
10
15 16
4
10
12
14
13
11
17
ITEM
QTY
PART N0.
DESCRIPTION
1
1
1
1
1
1
1
2
1
1
2
1
2
1
1
1
A/R
4
4
6
1
1
C2010050
C2010052
C4018002
C4018000
C5015004
C2614845
C6015240
C6015041
C6015238
C2614849
C2614842
C6015039
C6015032
C2010014
C2615367
C7014000
C8017010
C8003095
C8017008
300484
20351
BURNER INSERT HL, 6.10/6.20, WELDMENT
BURNER INSERT, HL, 10.10/20.10, WELDMENT
AUTO-IGNITION ELECTRODE
MONITORING ELECTRODE
INSPECTION GLASS, BURNER
COVER, INSPECTION GLASS, BURNER
WASHER, CABLE BUSHING, BURNER INSERT
SEAL, CABLE BUSHING BURNER INSERT
SCREW CONNECTION, CABLE BUSHING, BURNER INSERT
LINING PLATE, ELECTRODE, GAS
CLAMPING FLANGE, BURNER, HL, ø 50
SEAL, INSPECTION GLASS, BURNER
SEAL, BURNER ø 50 MM
BURNER, ø 50 x150, 20 KW
FLANGE, BURNER
COPPER PASTE
FLANGE NUT
HEXAGON BOLT, M5x16, HUD 20.20
NUT, LOCKING, SERRATED
TERM, PUSHON, .110, 22-16AWG SEMI INSUL. (NOT SHOWN)
TERM, SLIPON FULL INSUL .032X.25 TAB 22-18AWG (NOT SHOWN)
2
3
4
5
6
7
8
9
11
10
12
13
14
15
16
17
18
19
20
56
C2616521 C & C2616522 B
0706
ASSEMBLY, BURNER INSERT, AIR, LP & NAT GAS
ALL GAS MODELS
8
9
4
4
12
5
6
2
14
2
1
15
7
10
13 11
ITEM
QTY
PART N0.
DESCRIPTION
1
1
1
2
1
1
1
1
5
1
1
1
1
A/R
1
1
4
1
1
C2616521
C2616522
C6015034
C5018006
C6016009
C6016030
C6016000
C8012001
C6016023
C6016025
C2616516
C2616517
C7014000
C6017001
C6017009
C8017010
C2615355
111595
BURNER INSERT, HL, PRE-MOUNTED, 6.10/6.20
BURNER INSERT, HL, PRE-ASSEMBLED, 10.10/20.10
SEAL, FAN RG128/148
BURNER BLOWER, RG128, 110V
GAS VALVE, HONEYWELL, 110V
SEALING RING, GAS SCREEN
VENTURI 40 KW
SCREW, M5x12, FILLISTER HD, TORX
AUTOMATIC FIRING DEVICE, 110V, AUTO-IGNITION
COVER, AUTOMATIC FIRING DEVICE
GAS HOSE, 580mm LG, PREASSEMBLED, 6.20
GAS HOSE, 780mm LG, PREASSEMBLED, 10.10/20.10
COPPER PASTE
ORIFICE ø 400, LP GAS
ORIFICE, ø 0565 NAT GAS
FLANGE NUT
FLANGE, RESTRICTION ø 250
GASKET, CORK, BURNER VENTURI, COMBI
2
3
4
5
6
7
8
9
10
11
12
13
14
15
57
C2614860-1 A, C2614860 B, C2614862-1 B & C2614862 B
0706
DOOR 6.20 COMPLETE
OES 6.20 & 10.10 MODELS
4
2
1
3
5
6
7
8
ITEM
QTY
PART N0.
DESCRIPTION
1
1
1
1
1
1
1
2
1
1
1
A/R
A/R
C2514358
C2514359
C2514389
C2514390
C6012000
C6009016
C8015000
C2514430
C8001024
C8005021
C7004012
C7003087
ASSEMBLY, OUTER DOOR, 6.20
ASSEMBLY, OUTER DOOR, 10.10
ASSEMBLY, INNER DOOR, 6.20
ASSEMBLY, INNER DOOR, 10.10
DOOR HANDLE, LOCKING
PLASTIC LETTER "C" RED
MLF SCREW M6X8
UNHINGING SAFEGUARD, DOOR
SCREW, FILISTER HD, M4x10 DIN 7985
WASHER, 4.3, DIN 125
LOCTITE 243 (NOT SHOWN)
GREASE FRONT DOORS OD
2
3
4
5
6
7
8
9
10
58 40
C2514351SERV A & C2514352SERV A
0706
SLIDING PLATE, COMPLETE
ALL 6.20 &10.10 MODELS
Page 1 of 2
Upper Hinge C2013006
E
E
A
B
D
D
C
INSTALLED
ORIENTATION
ITEM
QTY
PART N0.
DESCRIPTION
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
2
2
2
2
2
1
11
2
5
4
1
1
11
4
2
2
2
1
7
A/R
2
C2614806
C2614807
C2614809
C6012002
C6012005
C2014008
C6015226
C6012006
C2013004
C8006057
C8006063
C8006060
C8004057
C8005050
C8003058
C8003043
C8013002
C8008095
C8001073
C8004040
C2014004
C8005041
C7004014
C8003066
C8013000
CARRIAGE PLATE, WELDED, 6.20
CARRIAGE PLATE, WELDED, 10.10 & 10.20
CARRIAGE PLATE, WELDED, 20.10 & 20.20
ASSEMBLED,GUIDE ROLLER RST CPL
DISC ø 39 x 6 RST
LOCKING BLOCK, CARRIAGE PLATE
LOCKING BLOCK RST
DOOR STOP, RST
HINGE, LOWER, WELDMENT, DOOR
SCHNORR LOCK WASHER
SCHNORR-LOCK WASHER
SCHNORR LOCK WASHER
NUT, HEX
WASHER, 8.4 A2 DIN 125
HEXAGON BOLT, M8 X 35
HEXAGON BOLT M6x16
FILLISTER HEAD SCREW DIN 912 - M8X25
BLIND RIVET NUT M6 ROUND
HEXAGON SOCKET SCREW M6x16
HEXAGON NUT
LOCKING PLATE, CARRIAGE, LOWER PART
WASHER 6.4 A2 DIN 9021
LOCTITE 638
BOLT, HEX HD, M10x30, 6.20, 10.10 & 10.20
BOLT, HEX HD, M10x25, 20.10 & 20.20
59
C2614801 B, C2614802 B & C2614804 P1
0706
SLIDING PLATE, COMPLETE
ALL 6.20 & 10.10 MODELS
Page 2 of 2
19 20
8
14 21
7
1
4
13 21
17
4
2
1
DETAIL B
17
DETAIL A
16
18
8
14
4
DETAIL C
8
6
20
11 21
15
3
22
10
9
5
14 21
SECTION D-D
SECTION E-E
60
C2614801 B, C2614802 B & C2614804 P1
0706
EXTERIOR SHEETING
ALL 6.20 & 10.10 MODELS
5
4
3
1
2
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
-
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
C2514351
C2514352
C2114652
C2114653
C2114782
C2114783
C2114762
C2114742
C2114763
C2114743
C2115462
C2115452
C2114702
111628
C2115463
C2115453
C2114700
111638
DOOR, 6.20, COMPLETE
DOOR, 10.10, COMPLETE
WELDMENT, CORNER, FRONT LEFT, 6.20
WELDMENT, CORNER, FRONT LEFT, 10.10
PANEL ASSY, LEFT, OGB 6.20, OGS 6.20, OEB 6.20, OES 6.20
PANEL ASSY, LEFT, OGB 10.10, OGS 10.10, OEB 10.10, OES 10.10
PANEL ASSY, REAR, OGB 6.20
PANEL ASSY, REAR, OGS 6.20, OEB 6.20, OES 6.20
PANEL ASSY, REAR, OGB 10.10
PANEL ASSY, REAR, OGS 10.10, OEB 10.10, OES 10.10
PANEL, TOP, OGB 6.20
PANEL, TOP, OGS 6.20
PANEL, TOP, OEB 6.20
PANEL, TOP, OES 6.20
PANEL, TOP, OGB 10.10
PANEL, TOP, OGS 10.10
PANEL, TOP, OEB 10.10
PANEL, TOP, OES 10.10
61
SERVICE SHEETING
0706
STAND, ASSEMBLY, CLOSED BASE
6.10 & 10.10 MODELS
FK111934 CASTOR STEM
REPLACEMENT KIT
11
7
14
15
16
13
1
6
8
12
10
18
2
9
17
4
3
5
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
1
2
1
1
2
2
1
4
1
2
3
24
8
8
8
8
1
1
C3216201
100413
C3216245
C3216249
100241
C3216237
C3216238
111673
111674
110492
104080
111686
111687
110715
23154
14262
110587
111669
WELDMENT, STAND, COMBI, 6.10/10.10
FOOT ASS'Y, ADJUSTABLE (FOR 1.250 SQ. TUBING), ANCHORABLE TIEDOWN
WELDMENT, STAND DOOR, 6.10/10.10, LEFT SIDE
WELDMENT, STAND DOOR, 6.10/10.10, RIGHT SIDE
FOOT, ADJUSTABLE (FOR 1.250 SQ. TUBE)
PANEL, STAND, LEFT & RIGHT SIDE, 6.10/10.10
SHEETING, TOP & REAR, COMBI STAND, 6.10/10.10
HINGE, COMBI STAND
CATCH, MAGNETIC, COMBI STAND
SCREW, 6-32 X 0.312, PAN HD, PHILLIPS, SST
SCREW, TR, PHH, 8x1/2, TYPE B, SST
SCREW, 10-32 X 0.500, COUNTERSUNK FLAT HEAD, SST
STUD, WELD, 6-32 X 0.188, CD, SST, NO FLANGE
WASHER, 0.158 ID X 0.340 OD X 0.032 THK, SST
WASHER, LOCK, INTERNAL TOOTH, #6, SST
NUT, HEX, 6-32, ACORN, SST
LABEL, SANITATION, UL CLASS NSF #2
LABEL, COMBI STAND, MODEL NO. CST-10-CB (6.10, 10.10)
63
C3216313 B
0706
ASSEMBLY, STACKING KIT, GAS MODELS
6.20 ON 6.20 OR 10.20,
6.10 ON 6.10 OR 10.10,
9
8
18
14
16
15
1
19
12
3
17
5
7
10
4
6
2
12
11
ITEM
QTY
PART N0.
DESCRIPTION
1
2
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
20
1
1
1
1
1
1
A/R
1
1
C3416377
C3416369
C3416363
C3416361
C2016200
C2016211
C2016212
C3416373
C3417044
C3416372
C3416392
C3416374
C2016204
C2016206
06162
C8001024
05250
05253
14335
108034
111704
111705
00909
111702
111703
WELDMENT, BASE, STACKING KIT, GAS, 6.20/10.20
WELDMENT, EXHAUST SHIELD, STACKING KIT, GAS
SHROUD, STACKING KIT, GAS, 6.20
SHROUD, STACKING KIT, GAS, 6.10
PIPE, STEAM EXHAUST, GAS, STACKING KIT
FLUE PIPE, STEAM GENERATOR, STACKING KIT, 6.20
FLUE PIPE, STEAM GENERATOR, STACKING KIT, 6.10
SHROUD, EXHAUST, STACKING KIT, GAS
BRACKET, COVER PLATE, STACKING KIT, GAS
COVER, EXHAUST SHROUD, STACKING KIT, GAS
GUIDE, FLUE, SHROUD, TOP, STACKING KIT, GAS 6.20
GUIDE, FLUE SHROUD, TOP, STACKING KIT, GAS, 6.10
FLUE PIPE, HOT AIR, STACKING KIT. 6.20
FLUE PIPE, HOT AIR, STACKING KIT, 6.10
FOOT, 6.00" ADJUSTABLE, FLANGED/TRI-BOLT HOLE PATTERN
SCREW, FILISTER HD, M4x10 DIN 7985
ELBOW, 90º, 1/2 NPT, BRASS (USED FOR STEAM GENERATOR)
ELBOW, STREET, 90º, 1/2 NPT, BRASS (USED FOR STEAM GENERATOR)
NIPPLE 0.500 NPT X 4.000, SCH 40, BRASS, TBE (USED FOR STEAM GENERATOR)
WASHER 3/4 GHT HOSE (USED FOR STEAM GENERATOR)
FITTING, 3/4 GHT MALE, X 1/2 NPT MALE, BRASS (USED FOR STEAM GENERATOR)
FITTING, 3/4 GHT FEMALE SWIVEL X 1/2 NPT FEMALE, BRASS (USED FOR STEAM GENERATOR)
THREAD SEALANT, LOCTITE 592 (USED FOR STEAM GENERATOR)
AIR DUCT, STACKING KIT, X.20 (USED FOR STEAM GENERATOR)
AIR DUCT, STACKING KIT, X.10 (USED FOR STEAM GENERATOR)
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
22
64
C3417021 C & C3417019 B
0706
ASSEMBLY, STACKING KIT,
ELECTRIC MODELS
6.10 ON 6.10 OR 10.10
12
8
10
3
9
4
13
1
11
2
6
7
6
5
ITEM
QTY
PART N0.
DESCRIPTION
1*
2*
3*
4*
5*
6*
7*
8
9
10
11
12
13
14
1
1
1
1
4
3
1
1
1
1
1
1
1
A/R
C3416368
C3416362
C3416365
C2016201
06162
C8001024
111703
05250
05253
14335
108034
111704
111705
00909
WELDMENT, BASE, STACKING KIT, ELECTRIC, 6.10/10.10
SHROUD, STACKING KIT, ELECTRIC, X.10
BRACKET, STEAM EXHAUST PIPE, STACKING KIT, ELECTRIC
PIPE, STEAM EXHAUST, ELECTRIC, STACKING KIT
FOOT, 6.00" ADJUSTABLE, FLANGED/TRI-BOLT HOLE PATTERN
SCREW, FILISTER HD, M4x10 DIN 7985
AIR DUCT, STACKING KIT, x.10
ELBOW, 90º, 1/2 NPT, BRASS
ELBOW, STREET, 90º, 1/2 NPT, BRASS
NIPPLE 0.500 NPT X 4.000, SCH 40, BRASS, TBE
WASHER 3/4 GHT HOSE
FITTING, 3/4 GHT MALE, X 1/2 NPT MALE, BRASS
FITTING, 3/4 GHT FEMALE SWIVEL X 1/2 NPT FEMALE, BRASS
THREAD SEALANT,LOCTITE 592
* Used for Steam Generator only.
65
C3417017 D
0706
CLEVELAND RANGE OGB 6.20/10.10
SEQUENCE OF OPERATIONS
When using these instructions refer to the OGB 6.20/10.10 wiring schematic.
1
When 120 VAC is applied to the combi, it is sent through the line filter (Z1) to the
Power Control Switch (S1).
2 When the Power Control Switch (S1) is closed
a The red light in the switch is energized.
b 120 VAC is sent through the 7 amp fuse (F10) to terminal 1 of connector X11 on
the Motor Drive (U10)
c 120vac is sent through the 2 amp fuse (F1.1) to
• The primary of the Hot Air 24v Transformer (T1)
◊ 24 VAC is sent from the secondary of the transformer to the Hot air
Burner Control (N20)
• The primary of the Steam 24v Transformer (T2)
◊ 24 VAC is sent from the secondary of the transformer to the Steam Burner
Control (N21)
• To terminal 12 of connector X1 on the Hot Air Burner Control (N20)
• To terminal 12 of connector X1 on the Steam Burner Control (N21)
• The 12 VDC Power Supply (G1)
◊ 12 VDC is sent to terminals 1 and 2 of connector X20 on the Gas Board
(A20)
◊ 12 VDC is sent to terminal 3 and 4 of connector X10 on the Control Board
(A10)
• To terminal 2 of connector X1 on the Hot Air Power Burner and Fan Control
(U20)
• To terminal 2 of connector X1 on the Steam Power Burner and Fan Control
(U21)
• To terminal 1 of connector X12 on the Control Board (A10)
d With 120 VAC to the Control Board (A10) The Operation Board (A11) is
energized
• An alarm will sound for one second
• All the LED’s and the display will energize one at a time.
• “STARTING” will be displayed for 3 seconds
• “Please wait” will be displayed
• The international model number will be displayed
• The time and date will be displayed and this will continue until the on/off
switch is depressed.
3 When the ON/OFF is depressed with the combi in the steam mode
a After a date change (the first time the combi is turned on) the display will ask
“Generator Flush?”. If no answer is given in 10 seconds or a yes is indicated the
flush will begin.
66
•
4
120 VAC is sent from terminal 1 of connector X13 on the Control Board
(A10) to the Generator Pump (M4).
• As the water level drops below the probes the fill solenoid (Y3) will energize.
This rocking of the water will help flush scale from the generator.
• Then the pump will be energized again
• When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC
is sent from terminal 5 of connector X12 to the condenser valve (Y1) until the
temperature drops.,
b The display will show the set temperature and set time.
c The Control Board (A10) will check the water level by looking for a ground at
terminals 1 and 2 on connector X15. These are connected to the high and low
probes (B1) in the steam generator.
• If the ground is not found 120 VAC is sent from terminal 7 on connector X12
on the Control Board (A10) to the fill solenoid (Y3)
• The fill solenoid opens and the generator is filled until both probes are
grounded.
◊ If the top probe becomes ungrounded for more that 5 seconds the fill
solenoid (Y3) will energize.
◊ If the bottom probe becomes ungrounded the combi will fill immediately
and the combi will not heat
d When the terminal 2 on connector X15 is grounded, the Control Board (A10)
transmits and receives a signal from terminals 5,6,7 and 8 on connector X10 to
terminals 3,4,5 and 6 of connector X28 on the Gas Board (A20)
• The Gas Board (A20) begins the steam generator heat circuit
◊ A signal is sent from terminal 8 of connector X24 to terminal 4 of
connector X2 on the Steam Power Burner and Fan Control (U21) selecting
the set speed of the combustion blower.
(a) When this speed is attained the signal is sent from terminal 2 of
connector X2 on the Steam Power Burner and Fan Control (U21) to
terminal 9 of connector X24 on the Gas Board (A20)
◊ A request for heat is sent from terminal 3 of connector X21 on the Gas
Board (A20) to terminal 10 on connector X1 on the Steam Burner Control
Module (N21)
(a) 24 VAC is sent from terminal 2 of connector X2 on the Steam Burner
Control Module (N21) to the hot surface igniter (R20).
(b) The gas valve is energized allowing gas and air into the burner
chamber to be ignited by the hot surface igniter.
(c) The Steam Burner Control Module (N21) senses at least 1.5 micro
amps DC from the flame sensor (P1) at terminal 3 of connector X2 and
sends a signal from terminal 2 of connector X1 to terminal 11 of
connector X25 on the Gas Board (A20)
• The steam generator heat circuit continues until 190 degrees F is detected
from the Steam Generator probe (B4) at terminals 1 and 2 of connector X17
on the Control Board (A10)
With the combi in the steam mode with time on the timer, the door closed and the
start switch is depressed
67
a
b
c
d
e
f
The front display will include a lighted bar under the steam symbol
• When the heat circuit is energized the heat symbol will be energized
• The cooking mode symbol will be energized.
• The time display will invert and begin to count down.
The fan circuit is energized by the Control Board (A10) transmitting and
receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5
and 6 of connector X28 on the Gas Board (A20)
The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the
Motor Drive.
• The motor Drive Board sends a signal through the thermal switch in the motor
from Terminal 5 and receives on terminal 6
• If the thermal switch is not open the Motor Drive Board (U10) sends 240
VAC 3 phase to the motor.
• The motor reverses direction every 120 seconds with a 15 second coast.
• NOTE: If the set temperature is less than 212 degrees F than fan will be
pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).
The steam generator heat circuit is energized
• A signal is sent from terminal 8 of connector X24 on the Gas Board (A20) to
terminal 4 of connector X2 on the Steam Power Burner and Fan Control
(U21) selecting the set speed of the combustion blower.
◊ When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Steam Power Burner and Fan Control (U21) to terminal 9 of
connector X24 on the Gas Board (A20)
• A request for heat is sent from terminal 3 of connector X21 on the Gas Board
(A20) to terminal 10 on connector X1 on the Steam Burner Control Module
(N21)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Steam Burner
Control Module (N21) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
◊ The Steam Burner Control Module (N21) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 11 of connector X25
on the Gas Board (A20)
• The heat circuit continues until both the cabinet set temperature and the
bypass probe (B5) are satisfied
◊ NOTE: If the set temperature is above 212 degrees F the hot air circuit
will be energized (after the by pass probe is satisfied) until the
compartment setting is reached. The steam circuit always takes
precedence.
When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is
sent from terminal 5 of connector X12 to the condenser valve (Y1) until the
temperature drops.
When the timer counts to 0 or the core temp probe (B10) reaches the set amount
the cycle ends and the steam generator reverts to the standby temperature of 190degree F.
68
5
With the combi in the Hot Air mode with time on the timer, the door closed and the
start switch is depressed
b The front display will include a lighted bar under the Hot Air symbol
• When the heat circuit is energized the heat symbol will be energized
• The cooking mode symbol will be energized.
• The time display will invert and begin to count down.
c The fan circuit is energized by the Control Board (A10) transmitting and
receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5
and 6 of connector X28 on the Gas Board (A20)
d The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the
Motor Drive.
• The motor Drive Board sends a signal through the thermal switch in the motor
from Terminal 5 and receives on terminal 6
• If the thermal switch is not open the Motor Drive Board (U10) sends 240
VAC 3 phase to the motor.
• The motor reverses direction every 120 seconds with a 15 second coast.
• NOTE: If the set temperature is less than 212 degrees F than fan will be
pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).
e Hot air heat circuit is energized
• A signal is sent from terminal 2 of connector X24 on the Gas Board (A20) to
terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control
(U20) selecting the set speed of the combustion blower.
◊ When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 3 of
connector X24 on the Gas Board (A20)
• A request for heat is sent from terminal 3 of connector X20 on the Gas Board
(A20) to terminal 10 on connector X1 on the Hot Air Control Module (N20)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control
Module (N20) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 10 of connector X25
on the Gas Board (A20
69
f
g
5
The heat circuit will remain energized until the cabinet set temperature is reached
When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is
sent from terminal 5 of connector X12 to the condenser valve (Y1) until the
temperature drops.
h If the “Crisp and Tasty” mode is selected
• 120 VAC is sent from terminal 6 of connector X12 on the Control Board
(A10) to the Dehumidification Valve (Y2) to pull the humidity out of the
cabinet down the drain.
◊ In the light and medium modes (one and two drops in the display) the Y2
valve will be energized until the bypass probe (B5) is satisfied.
◊ In the full mode (3 drops in the display) the Y2 valve will be energized
continuously.
i When the timer counts to 0 or the core temp probe (B10) reaches the set amount
the cycle ends and the steam generator reverts to the standby temperature of 190degree F.
With the combi in the Combi mode with time on the timer, the door closed and the
start switch is depressed
a The front display will include a lighted bar under the Combi symbol
• When the heat circuit is energized the heat symbol will be energized
• The cooking mode symbol will be energized.
• The time display will invert and begin to count down.
b The fan circuit is energized by the Control Board (A10) transmitting and
receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5
and 6 of connector X28 on the Gas Board (A20)
c The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the
Motor Drive.
• The motor Drive Board sends a signal through the thermal switch in the motor
from Terminal 5 and receives on terminal 6
• If the thermal switch is not open the Motor Drive Board (U10) sends 220
VAC 3 phase to the motor.
• The motor reverses direction every 120 seconds with a 15 second coast.
• NOTE: If the set temperature is less than 212 degrees F than fan will be
pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).
d The steam generator heat circuit is energized. Steam production takes precedence
in the Combi mode
• A signal is sent from terminal 8 of connector X24 on the Gas Board (A20) to
terminal 4 of connector X2 on the Steam Power Burner and Fan Control
(U21) selecting the set speed of the combustion blower.
70
◊
e
f
g
When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Steam Power Burner and Fan Control (U21) to terminal 9 of
connector X24 on the Gas Board (A20)
• A request for heat is sent from terminal 3 of connector X21 on the Gas Board
(A20) to terminal 10 on connector X1 on the Steam Burner Control Module
(N21)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Steam Burner
Control Module (N21) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
◊ The Steam Burner Control Module (N21) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 11 of connector X25
on the Gas Board (A20)
After the bypass probe (B5) is satisfied then the hot air heat circuit is energized to
increase the cabinet temperature to the setting.
• A signal is sent from terminal 2 of connector X24 on the Gas Board (A20) to
terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control
(U20) selecting the set speed of the combustion blower.
◊ When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 3 of
connector X24 on the Gas Board (A20)
• A request for heat is sent from terminal 3 of connector X20 on the Gas Board
(A20) to terminal 10 on connector X1 on the Hot Air Control Module (N20)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control
Module (N20) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 10 of connector X25
on the Gas Board (A20
• The heat circuit will remain energized until the cabinet set temperature is
reached
• If the bypass probe (B5) drops below the set level the steam heat circuit will
start again.
When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is
sent from terminal 5 of connector X12 to the condenser valve (Y1) until the
temperature drops.
If the “Crisp and Tasty” mode is selected
• 120 VAC is sent from terminal 6 of connector X12 on the Control Board
(A10) to the Dehumidification Valve (Y2) to pull the humidity out of the
cabinet down the drain.
◊ In the light and medium modes (one and two drops in the display) the Y2
valve will be energized until the bypass probe (B5) is satisfied.
71
◊
6
In the full mode (3 drops in the display) the Y2 valve will be energized
continuously.
h When the timer counts to 0 or the core temp probe (B10) reaches the set amount
the cycle ends and the steam generator reverts to the standby temperature of 190degree F.
With the combi in the Rethermalization mode with time on the timer, the door closed
and the start switch is depressed
a The front display will include a lighted bar under the Retherm symbol
• When the heat circuit is energized the heat symbol will be energized
• The cooking mode symbol will be energized.
• The time display will invert and begin to count down.
b The fan circuit is energized by the Control Board (A10) transmitting and
receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5
and 6 of connector X28 on the Gas Board (A20)
c The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the
Motor Drive.
• The motor Drive Board sends a signal through the thermal switch in the motor
from Terminal 5 and receives on terminal 6
• If the thermal switch is not open the Motor Drive Board (U10) sends 220
VAC 3 phase to the motor.
• The motor reverses direction every 120 seconds with a 15 second coast.
• NOTE: If the set temperature is less than 212 degrees F than fan will be
pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).
d The steam generator heat circuit is energized. Steam production takes precedence
in the Combi mode
• A signal is sent from terminal 8 of connector X24 on the Gas Board (A20) to
terminal 4 of connector X2 on the Steam Power Burner and Fan Control
(U21) selecting the set speed of the combustion blower.
◊ When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Steam Power Burner and Fan Control (U21) to terminal 9 of
connector X24 on the Gas Board (A20)
• A request for heat is sent from terminal 3 of connector X21 on the Gas Board
(A20) to terminal 10 on connector X1 on the Steam Burner Control Module
(N21)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Steam Burner
Control Module (N21) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
◊ The Steam Burner Control Module (N21) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 11 of connector X25
on the Gas Board (A20)
e After the bypass probe (B5) is satisfied then the hot air heat circuit is energized to
increase the cabinet temperature to the setting.
72
•
f
g
A signal is sent from terminal 2 of connector X24 on the Gas Board (A20) to
terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control
(U20) selecting the set speed of the combustion blower.
◊ When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 3 of
connector X24 on the Gas Board (A20)
• A request for heat is sent from terminal 3 of connector X20 on the Gas Board
(A20) to terminal 10 on connector X1 on the Hot Air Control Module (N20)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control
Module (N20) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 10 of connector X25
on the Gas Board (A20
• The heat circuit will remain energized until the cabinet set temperature is
reached
• If the bypass probe (B5) drops below the set level the steam heat circuit will
start again.
When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is
sent from terminal 5 of connector X12 to the condenser valve (Y1) until the
temperature drops.
When the timer counts to 0 or the core temp probe (B10) reaches the set amount
the cycle ends and the steam generator reverts to the standby temperature of 190degree F.
73
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
CLEVELAND RANGE, LLC
1333 East 179th St., Cleveland, Ohio 44110-2574
TITLE
WIRING DIAGRAM
OGB 6.20/10.10
74
VOLTAGE:
WATTAGE:
CURRENT:
120VAC
10.25W
11.7A
DRAWN BY
DATE
DRL
7-25-05
DRAWING NO.
SIZE
B
REV
300493
A
SHEET 1 OF 9
1
2
3
4
5
BK 12
1
2
1
/4.B3
/4.B3
-A20:X26:1
2
BU 18
BU 18
/3.B5
/3.B5
-A10:X15:9
/3.B5
-A10:X15:11
BN
OR
-A10:X15:10
BU 18
BK 18
COM
TxD
BU 18
VOLTAGE:
WATTAGE:
CURRENT:
WIRING DIAGRAM
OGB 6.20/10.10
4
75
TW/GY
TW/GY
RD 18
3
BN
3
BU 18
2
2
1
BK
1
RD 18
W1/BN
RD
8
8
7
7
2
3
3
9
-BM1
V1/BU
E
RPM
FAN
/3.F1
TITLE
3
-X13.6
GND
SH
-X10:21
-X13.5
U1/BK
M 3~
U2/RD
-M1
2
9
BK 18
6
6
BK 18
BK 18
5
4
4
-A20:X28:2
-A10:X10:4
/3.D4
/4.E3
-A10:X10:3
5
BU 18
BU 18
RD 18
RD 18
-A20:X28:1
/3.D4
/4.E3
-X13.2
V2/WH
1333 East 179th St., Cleveland, Ohio 44110-2574
BK
GR
-X10:101
W2/YE
CLEVELAND RANGE, LLC
C
D
-X13.1
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
L1 L2
U V W
GN 18
-W2
CABLE
E
RD 18
RD 18
GND
/5.E5
0V
12V
L1 N
D
RxD
12V
RD 18
L
-G1
12V DC
1
2
POWER SUPPLY
12VDC
96-264V
AC
3
1
N
G
102
GND
GND
P1 P2
MOTOR DRIVE
/3.D6
1
GR
BU 12
-U10
RD 18
-A10:X12:1
C
B
31
BU 18
-X10
RD 18
2
RD 18
N
GND
L
BK 12
-X10
20
-F10
15A
2A
-X10
F
/4.B3
1
L1
-F1.1
LINE FILTER
-X10
-A20:X26:3
BU 12
-Z1
B
30
1
N1
BK 12
/4.B3
2
RD
4
-X10
-A20:X26:2
5
A
3
BK 12
6
8
WIRING DIAGRAM
BK 12
-A20:X26:4
-S1
7
BU 12
CONTROL POWER
A
6
DRAWN BY
120VAC
10.25W
11.7A
DATE
5
DRAWING NO.
DRL
SIZE
7-25-05
6
B
REV
300493
A
SHEET 2 OF 9
7
8
F
F
-X10:20
-X10
2
D5
D4
-A10:X10:11
RD
-A10:X10:12
-A10:X10:10
BU
D4
-A10:X10:9
WH
-B1
D4
WATER LEVEL PROBE
BK
BU
RD
1
10
5
6
7
4
8
7
6
PUMP/CLEANING AGENT
5
PUMP/RINSE
4
COMPARTMENT RINSE VALVE
3
STEAM GEN OVER TEMP
2
STEAM GEN PUMP
1
C
-X10
RD 18
RD 18
BU 18
HIGH LEVEL
GND
LOW LEVEL
156
RD 18
157
RD 18
GND
DOOR SW
2
X13:
D
-X10:33
M
-Y20
1~
CONDENSER
TITLE
VOLTAGE:
WATTAGE:
CURRENT:
WIRING DIAGRAM
OGB 6.20/10.10
3
4
76
STEAM GENERATOR
FILLING
-X10
DATE
5
22
DRAWING NO.
DRL
SIZE
7-25-05
6
B
CLEANING AGENT
FBS2-6
-X10:23
STEAM GENERATOR
PUMP
DRAWN BY
120VAC
10.25W
11.7A
N
CLEANING AGENT
BU 18
DEHUMIDIFICATION
N
N
RINSING AGENT
N
BU 18
-Y23
-Y22
WATER CLEANING
E
L
A2
A2
-M4
L
-Y21
-Y3
L
RD 18
A1
CLEANING OPTION ONLY
A1
RD 18
RD 18
FBS2-6
OVEN LAMP
1333 East 179th St., Cleveland, Ohio 44110-2574
X14:
3
FBS2-6
BU 18
CLEVELAND RANGE, LLC
3
4
RD 18
-A13:X1:4
-A13:X1:3
A8
32
21
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
1
2
5
9
L
-Y1
A1
100
BU 18
FBS2-6
/5.A4
1
6
-A20:X20:1
A2
X1
-H5.1
GND
X2
-M3.1
-X10
A2
-Y2
COOLING FAN
/4.E5
A1
M
/2.F4
A8
A8
-X10
A8
/4.E4
/4.E4
/4.E4
/4.E4
-G1:12V
/2.E3
-Y10
RD 18
2
RD
BK
1A
1~
X12:
8
7
1
RD 18
/2.E3
D
E
7
8
136
6
CABLE CONNECTION SM ON BM -W1
CONTROL 500
-F2.1
RD 18
/2.C8
/2.C7
5
10 9
134
4
RD 18
3
B
IDENTIFICATION MODULE
1
133
-A13:X1:2
2
2
3
RD 18
-A13:X1:1
1
4
GEN FILL/VALVE
10 11 12
X11:
5
DEHUMIDICATION/VALVE
9
6
CONDENSOR/VALVE
IDM (WH)
8
7
OVEN LAMP
IDM (BK)
7
8
L1- 110/120
TxD
6
RESET
5
-A20:X28:5
GND
RxD
4
-A20:X28:3
0VDC IN
3
-A20:X28:4
12VDC IN
2
-A20:X28:6
12VDC FAN
1
-G1:0V
12VDC FAN
1
-X13.5:3
/2.C7
-X13.5:1
X15:
X10:
CONTROL BOARD
-X13.5:2
GN/BU
14 13 12 11 10 9
1
2
3
GND
4
4
1
-X10:31
SM 5010
X19:
13
14
KTM
CTC
GN
-B10
5
GN/RD
GN
GN
6
X16:
C
14
PROBE OVEN
-B6
7
2 3
A
H
/2.C4
X18:
WH
YL
8
X17:
1
13
PROBE BYPASS
-B5
RD
YL
PROBE CONDENSER
-B3
RD
12 11 10 9
8
-A13
PRES. SW
1
YL
RD
PROBE)
-B4 (TEMP
STEAM GENERATOR
2
3
RESET
4
MOTOR SPEED (M1)
5
7
L
-X10
+12VDC
6
CLEANING OPTION ONLY
GND (M1 H.E. SENSOR)
7
-S7
-S2
CLEANING PRESSURE SWITCH
IDM (RD)
-A10
8
6
DOOR MAGNET SWITCH
IDM (BU)
10 9
YL
X39: 1
-A12
RD
B
RD
PICTO
MODULE
YL
BM 5010
OPERATION BOARD
5
BURNER SUPPLY
WIRING DIAGRAM
-A11
(OPTION)
4
RD 18
3
-B8 ELEMENT (PROBE)
A
2
OVER TEMPERATURE
STEAM GEN.
1
/5.A1
REV
300493
A
SHEET 3 OF 9
7
8
F
F
1
CLEVELAND RANGE, LLC
1333 East 179th St., Cleveland, Ohio 44110-2574
2
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
3
77
6
8
TITLE
WIRING DIAGRAM
OGB 6.20/10.10
4
1 2
3
4
5
6
-X10
VOLTAGE:
WATTAGE:
CURRENT:
40
7
8
120VAC
10.25W
11.7A
5
X20:
9 10
41
-N20:X1:10
-N20:X1:5
DRAWN BY
DATE
ALARM STEAM GEN.
1
ALARM STEAM GEN. (DE)
2
HEAT REQUEST (DE)
3
PWM CONVECTION 1
GROUND CONVECTION 1
4
1 2
3
4
5
RD 18
5
RD 18
6
RD 18
7
RD 18
8
RESET STEAM GEN.
12 11 10 9
-U20:X2:3
-U20:X2:4
-U20:X2:2
-U21:X2:3
/5.B7
/5.B7
/5.B7
/6.C7
/6.C7
/6.C7
-N21:X1:1
-N20:X1:1
/6.C3
/5.C3
5
-X10
DRL
7-25-05
6
RESET STEAM GEN.
1
SPEED CONVECTION 1
-U21:X2:2
BU 18
-U21:X2:4
/5.C3
/6.C3
46
GROUND STEAM GENERATOR
ALARM CONVECTION 1
SPEED STEAM GENERATOR
-N20:X1:2
4
PWM STEAM GENERATOR
HEAT REQUEST HL1
ALARM CONVECTION 1
9
RD 18
X28:
RESET CONVECTION 1 (HL1)
10
RD 18
X24:
RD 18
GAS BOARD
2
PHASE ( L1 )
RESET CONVECTION 1
9
3
RD 18
4
-N21:X1:11
7
5
-N20:X1:11
6
-X10:32
7
/6.C4
5
RD 18
GND
4
-A10:X10:5
3
BU 18
1 2
8
/3.D6
D
-N21:X1:2
/2.A6
/2.A6
/2.A6
/2.A6
3
/5.C4
12
-A10:X10:8
12 11 10 9
/3.D4
11
RESET
GM5010
CONVECTIO 1 FLAME OK
GND. FIRING AUTOMAT
-U10:COM
-U10:12V
-U10:RxC
-U10:RxD
A
/3.D4
5
RD 18
4
STEAM GEN 1 FLAME OK
3
-A10:X10:6
12V
SIGNAL GND
X25:
/3.D4
1
TxD_12V
8
2
0VDC IN
2
3
RxD_12V
X26:
4
RD 18
X27:
5
-A10:X10:7
7
12VDC IN
6
6
RD 18
1
7
-G1:0V
8
/3.D4
E
-G1:12V
C
2
/2.E3
/2.E3
-A20
RECIEVE
B
TRANSMIT
1
6
7
6
42
5
/5.C4
/5.C4
SIZE
4
6
3
7
DRAWING NO.
B
2
X22:
8
-N21:X1:10
-N21:X1:5
7
8
WIRING DIAGRAM
A
-X10
B
1
X23:
9
8
6
7
5
4
C
3
1
2
X21:
9
D
E
43
/6.C4
/6.C4
300493
REV
A
SHEET 4 OF 9
8
F
4
5
WIRING DIAGRAM
23
-X10:22
/3.D5
A
FBS 2-5
-X10:32
A
(BURNER SUPPLY / 120V)
1
GND
/4.B6
/4.B6
2
X3:
RD 18
BU 18
RD 18
3
3
4
PWM CONVECTION 1
X1:
101
5
X2:
D
1
GN 18
/2.C5
E
2
1
-U10:GND
-R20
2
GN 18
-X10
RD 18
HOT SURFACE IGNITION
(HOT AIR)
1
1
FLAME SENSOR
-A20:X24:2
/4.B6
BURNER FAN
(HOT AIR)
GN 18
BU 18
RD 18
-U20
11 12
X2:
2
-A20:X24:1
-A20:X24:3
(RESET AIR HEAT)
-A20:X20:2
(RESET AIR HEAT/GO)
/4.E5
-X10:41
9 10
X1:
-P1
E
RD 18
7 8
C
SPEED CONVECTION 1
6
B
GROUND CONVECTION 1
5
/4.F6
22
-X10:40
(RESET CONV. 1 (HL1)
RD 18
4
RD 18
60
(HI-LIMIT)
(HI-LIMIT)
(NEUTRAL)
/4.F6
3
BURNER CONTROL
(HOT AIR)
3
61
/6.A1
-X10:24
/6.A4
GND
2
RD 18
1
RD 18
-N20
BU 18
RD 16
RD 18
BU 18
RD 16
BU 18
24 VAC
-X10
8
33
21
-B7.1
-A20:X25:10
(GND)
(FLAMECHECK)
/4.B4
-X10:46
-T1
BU 18
BU 16
BK 16
OR 16
WH 16
120VAC
/4.A4
B
D
-X10:34
7
STB
OVER TEMPERATURE THERMOSTAT
(HOT AIR)
RD 18
BU 18
RD 18
-X10
C
6
RD 18
-X10
3
L1
/3.F8
2
N
1
BU 18
F
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
CLEVELAND RANGE, LLC
1333 East 179th St., Cleveland, Ohio 44110-2574
1
2
TITLE
VOLTAGE:
WATTAGE:
CURRENT:
WIRING DIAGRAM
OGB 6.20/10.10
3
4
78
DRAWN BY
120VAC
10.25W
11.7A
DATE
5
DRAWING NO.
DRL
SIZE
7-25-05
6
B
REV
300493
A
SHEET 5 OF 9
7
8
F
5
/5.A5
A
103
GND
/4.B5
/4.B5
-A20:X24:7
3
-A20:X24:8
-A20:X24:9
2
C
4
5
PWM STEAM GEN
GN 18
-X10
RD 18
/4.B5
1
BU 18
RD 18
GN 18
X1:
3
1
RD 18
-P2
FLAME SENSOR
2
SPEED STEAM GEN
X2:
2
1
STEAM GENERATOR
BURNER FAN
GROUND STEAM GEN
-U21
12
GND
11
RD 16
9 10
(BURNER SUPPLY / 120V)
(RESET AIR HEAT/GO)
(RESET AIR HEAT)
/4.E6
7 8
RD 16
6
RD 16
-X10:43
-A20:X21:1
/4.F7
22
5
B
X1:
3
RD 18
(Hi-Limit)
-X10:42
4
STEAM GENERATOR
BURNER CONTROL
E
(Hi-Limit)
(NEUTRAL)
BU 16
3
RD 16
2
RD 16
1
(ALARM STEAM GEN (DE))
/4.B3
/4.F7
(GND)
(FLAMECHECK)
/4.A4
-X10:46
-N21
RD 16
RD 16
24 VAC
BU 16
BU 16
-T2
RD 16
BU 16
BK 16
WH 16
OR 16
120VAC
-A20:X25:11
BU 18
RD 18
B
34
21
-B7.2
OVER TEMPERATURE THERMOSTAT
(STEAM GENERATOR)
BU 18
8
-X10:33
-X10
D
7
WIRING DIAGRAM
24
A
C
6
RD 18
-X10
4
BU 18
-X10:23
3
N
/5.A8
2
L1
1
X2:
D
X3:
1
GN 18
2
-R21
HOT SURFACE IGNITION
(STEAM GEN)
E
1
RD 18
BU 18
F
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
CLEVELAND RANGE, LLC
1333 East 179th St., Cleveland, Ohio 44110-2574
1
2
TITLE
VOLTAGE:
WATTAGE:
CURRENT:
WIRING DIAGRAM
OGB 6.20/10.10
3
4
79
DRAWN BY
120VAC
10.25W
11.7A
DATE
5
DRAWING NO.
DRL
SIZE
7-25-05
6
B
REV
300493
A
SHEET 6 OF 9
7
8
F
1
3
4
5
6
7
8
N
N
A
2
A
N
2
1
3
120 VAC
RD
4
3
L1
6
L1
LINE FILTER
-Z1
L1
CONTROL
POWER
-S1
15A
-F1.1
-F10
B
B
LADDER DIAGRAM
2A
0
120VAC
24 VAC
2
12V
4
RxD
3
TxD
1
COM
P2 P1 W V
U
GND
M 3~
V1/BU
SH
GND
U1/BK
RECIEVE
GND
W2/YE
V2/WH
U2/RD
W1/BN
80
5
SIZE
7-25-05
6
B
D
E
/9.B5)
4
12V(FOR SENSOR)
3
11
2
DATE
DRAWING NO.
DRL
C
-A10:X15
1
WIRING DIAGRAM
OGB 6.20/10.10
DRAWN BY
120VAC
10.25W
11.7A
MOTOR SPEED M1
1333 East 179th St., Cleveland, Ohio 44110-2574
VOLTAGE:
WATTAGE:
CURRENT:
GND M1
9
CLEVELAND RANGE, LLC
TITLE
10
STEAM
TRANSFORMER
-T2
CONVECTION
-M1
24
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
RD
BK
RPM
BN
SENSOR
/8.C4
FAN
12V
TRANSMIT
-A20:X26
120VAC
24 VAC
24 VAC
F
-BM1
HOT AIR
TRANSFORMER
-T1
0
E
MOTOR DRIVE
-U10
L
24
D
GND L2
24 VAC
C
REV
300493
A
SHEET 7 OF 9
7
8
F
-R21
24
FLAMECHECK
GND
NEUTRAL
Hi-Limit
Hi-Limit
RESET AIR HEAT/GO
24 VAC
RESET AIR HEAT
1
2
0
PHASE ( L1 )
2
X2
-P2
FLAME
SENSOR
3
GAS
VALVE
24
1
HOT AIR BURNER
CONTROL MODULE
-N20
FLAMECHECK
GND
NEUTRAL
Hi-Limit
Hi-Limit
RESET AIR HEAT/GO
24 VAC
RESET AIR HEAT
0
PHASE ( L1 )
9
11
1
GND. FIRING AUTOMAT
X3:
STEAM GEN. FLAME OK
X25
9
22
21
-B7.2
6-9 NOT USED
SPEED STEAM GENERATOR
6
5
4
ALARM STEAM GEN. (DE)
PWM STEAM GENERATOR
GROUND STEAM GENERATOR
ALARM STEAM GEN.
9
8
7
HEAT REQUEST (DE)
3
RESET STEAM GEN.
2
1
RESET STEAM GEN.
1
X21
1
3
4
GND
RECIEVE
TRANSMIT
12V
2
9
21
2
3
1
X3:
-B7.1
ALARM HOT AIR 1
5
X1:
GND. FIRING AUTOMAT
HOT AIR 1 FLAME OK
X25
ALARM HOT AIR 1
6
22
4
1
GROUND HOT AIR 1
2
PWM HOT AIR 1
3
SPEED HOT AIR 1
HEAT REQUEST HL1
RESET HOT AIR 1 (HL1)
3
RESET HOT AIR 1
2
1
PHASE ( L1 )
X20
X28
/9.C5
-X10:32
(-A10:X11:8)
(CONTROL BOARD)
1
2
4
3
5
6
1
X1:
2
3
L1
L1
FLAME
SENSOR
-P1
-R20
HOT SURFACE
IGNITER
1
2
2
X2
3
10
3
5 4
6
8 7
HOT SURFACE IGNITOR
GAS
VALVE
1
12
X1:
/7.C5
12 11 10 9
8
SHEET 8 OF 9
D
C
B
L
120 VAC
-G1
N
12V
0V
N
90-264VAC
POWER SUPPLY
12VDC
GND
3
F
E
1
2
3
5 4
6
8 7
7
REV
X1:
0VDC IN
12VDC IN
TxD_12V
RxD_12V
RESET
GND
/9.D3
-A10:X10
CONTROL BOARD
B
A
300493
STEAM BURNER
CONTROL MODULE
-N21
6
7-25-05
DRAWING NO.
11 10 9
X21
X26
GAS BOARD
-A20
(GM)
X24
1
2
3
X2:
4
5
-U20
HOT AIR
POWER BURNER
FAN CONTROL
L1
12
0
2
A
N
N
12VDC
MOTOR DRIVE
-U10:X12
1
2
3
X2:
5
4
-U21
STEAM
POWER BURNER
FAN CONTROL
LADDER DIAGRAM
5
SIZE
DRL
1
4
DATE
DRAWN BY
2
81
3
WIRING DIAGRAM
OGB 6.20/10.10
120VAC
10.25W
11.7A
X25
2
VOLTAGE:
WATTAGE:
CURRENT:
TITLE
X25
1
1333 East 179th St., Cleveland, Ohio 44110-2574
CLEVELAND RANGE, LLC
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
X20
F
E
D
C
B
A
1
4
5
6
7
8
N
12
X1
L1
-M3.1
M
1
X18:
X19:
10 9
X16:
X17:
1
5
4
8
7
6
8
7
6
5
4
3
2
2 3
9 10 11 12
1
3
2
1
12 11 10 9
8
7
7
6
5
4
STEAM GEN
6
5
4
3
GN/BU
GN/RD
GN
GN
GN
WH
YL
RD
YL
RD
YL
RD
YL
RD
YL
RD
-A11
BM 5010
OPERATION MODULE
PICTO
-A12
(OPTION)
MODULE
OVER TEMPERATURE
STEAM GEN.
ELEMENT (PROBE)
PROBE BYPASS
PROBE CONDENSER
(TEMP PROBE)
STEAM GENERATOR
-B3
PROBE OVEN
2
1
1
2
3
CLEANING PRESSURE SWITCH
CLEANING OPTION ONLY
4
14 13 12 11 10 9
DOOR MAGNET SWITCH
14
-S2
13
8
-B1
7
-S7
13
5
6
6
5
4
1
2
3
WATER LEVEL PROBE
14
KTM
CTC
-B5
BU
RD
/7.C3
-M1
-B10
-B6
-B4
-B8
X39: 1
LADDER DIAGRAM
SM 5010
-A10
CONTROL BOARD
12VDC FAN (+)
12VDC IN
X10:
12VDC FAN (-)
GND
RxD_12V
0VDC IN
TxD_12V
L1- 110/120 VAC-INPUT
IDM (RD)
IDM (BU)
IDM (WH
IDM (BK)
RESET
3
5
1
HOT AIR
OVEN LAMP
CONDENSOR/VALVE
X12:
GEN FILL/VALVE
DEHUMIDICATION/VALVE
X15:
SENSOR GND M1
12v(FOR SENSOR)
RESET
MOTOR SPEED M1
GND
GND
PRES. SW
DOOR SW
4
7
8
L
4
3
2
1
STEAM GEN PUMP
GND
LOW LEVEL
STEAM GEN OVER TEMP
X14:
HIGH LEVEL
COMPARTMENT RINSE V.
5
7
6
L1
PUMP / CLEAN AGENT
X13:
PUMP / RINSE
BURNER SUPPLY
X11:
1
2
2
3
I.D. MODULE
-A13
-F2.1
/8.D4
-A20:X20:1
(GAS BOARD)
-X10:32
-Y21
1
4
-Y1
-Y3
M
6
-M4
/8.D5
-A20:X28
(GAS BOARD)
-Y2
X2
12VDC
0
-H5.1
-Y20
-Y22
-Y23
8
L2
82
SHEET 9 OF 9
B
7-25-05
8
7
6
5
4
3
2
9
10 9
8
7
6
5
1
SIZE
DATE
1333 East 179th St., Cleveland, Ohio 44110-2574
A
WIRING DIAGRAM
OGB 6.20/10.10
CLEVELAND RANGE, LLC
F
REV
300493
DRAWING NO.
DRL
DRAWN BY
120VAC
10.25W
11.7A
VOLTAGE:
WATTAGE:
CURRENT:
TITLE
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
10
4
3
2
H
F
D
D
E
E
C
C
B
B
A
A
8
7
6
5
4
3
2
1
1
CLEVELAND RANGE OGS 6.20/10.10
SEQUENCE OF OPERATIONS
When using these instructions refer to the OGS 6.20/10.10 wiring schematic.
1
When 120 VAC is applied to the combi, it is sent through the line filter (Z1) to the
Power Control Switch (S1).
2 When the Power Control Switch (S1) is closed
a The red light in the switch is energized.
b 120 VAC is sent through the 7 amp fuse (F10) to terminal 1 of connector X11 on
the Motor Drive (U10)
c 120vac is sent through the 2 amp fuse (F1.1) to
• The primary of the Hot Air 24v Transformer (T1)
◊ 24 VAC is sent from the secondary of the transformer to the Hot air
Burner Control (N20)
• The primary of the Steam 24v Transformer (T2)
◊ 24 VAC is sent from the secondary of the transformer to the Steam Burner
Control (N21)
• To terminal 12 of connector X1 on the Hot Air Burner Control (N20)
• To terminal 12 of connector X1 on the Steam Burner Control (N21)
• The 12 VDC Power Supply (G1)
◊ 12 VDC is sent to terminals 1 and 2 of connector X20 on the Gas Board
(A20)
◊ 12 VDC is sent to terminal 3 and 4 of connector X10 on the Control Board
(A10)
• To terminal 2 of connector X1 on the Hot Air Power Burner and Fan Control
(U20)
• To terminal 2 of connector X1 on the Steam Power Burner and Fan Control
(U21)
• To terminal 1 of connector X12 on the Control Board (A10)
d With 120 VAC to the Control Board (A10) The Operation Board (A11) is
energized
• An alarm will sound for one second
• All the LED’s and the display will energize one at a time.
• “STARTING” will be displayed for 3 seconds
• “Please wait” will be displayed
• The international model number will be displayed
• The time and date will be displayed and this will continue until the on/off
switch is depressed.
3 When the ON/OFF is depressed with the combi in the steam mode
a The display will show the set temperature and set time.
4 With the combi in the steam mode with time on the timer, the door closed and the
start switch is depressed
a The front display will include a lighted bar under the steam symbol
83
5
• When the heat circuit is energized the heat symbol will be energized
• The cooking mode symbol will be energized.
• The time display will invert and begin to count down.
b The fan circuit is energized by the Control Board (A10) transmitting and
receiving a signal from terminals 5,6, and 7 on connector X10 to connector X12
on the Motor Drive Board (U10).
• The motor Drive Board sends a signal through the thermal switch in the motor
from Terminal 5 and receives on terminal 6
• If the thermal switch is not open the Motor Drive Board (U10) sends 240
VAC 3 phase to the motor.
• The motor reverses direction every 120 seconds with a 15 second coast.
c Hot air heat circuit is energized
• A signal is sent from terminal 8 of connector X15 on the Control Board (A10)
to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control
(U20) selecting the set speed of the combustion blower.
◊ When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 2 of
connector X15 on the Control Board (A10)
• A request for heat is sent from terminal 3 of connector X12 on the Control
Board (A10) to terminal 10 on connector X1 on the Hot Air Control Module
(N20)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control
Module (N20) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 12 of connector X15
on the Control Board (A10)
• The heat circuit will remain energized until the cabinet set temperature is
reached as sensed at probe B6.
d The steam circuit is energized
• 120 VAC is sent from terminal 4 of connector X12 on the Control Board
(A10) to the coil of the Y3 solenoid allowing water to be thrown against the
element until the bypass probe (B5) senses 183 degrees F.
◊ NOTE: If the set temperature is above 212 degrees F the hot air circuit
will be energized (after the by pass probe is satisfied) until the
compartment setting is reached.
e When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is
sent from terminal 5 of connector X12 to the condenser valve (Y1) until the
temperature drops.
f When the timer counts to 0 or the core temp probe (B10) reaches the set amount
the cycle ends and the steam generator reverts to the standby temperature of 190degree F.
With the combi in the Hot Air mode with time on the timer, the door closed and the
start switch is depressed
84
a
c
b
c
d
The front display will include a lighted bar under the Hot Air symbol
• When the heat circuit is energized the heat symbol will be energized
• The cooking mode symbol will be energized.
• The time display will invert and begin to count down.
The fan circuit is energized by the Control Board (A10) transmitting and
receiving a signal from terminals 5,6, and 7 on connector X10 to connector X12
on the Motor Drive Board (U10).
• The motor Drive Board sends a signal through the thermal switch in the motor
from Terminal 5 and receives on terminal 6
• If the thermal switch is not open the Motor Drive Board (U10) sends 240
VAC 3 phase to the motor.
• The motor reverses direction every 120 seconds with a 15 second coast.
• NOTE: If the set temperature is less than 212 degrees F than fan will be
pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).
Hot air heat circuit is energized
• A signal is sent from terminal 8 of connector X15 on the Control Board (A10)
to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control
(U20) selecting the set speed of the combustion blower.
◊ When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 2 of
connector X15 on the Control Board (A10)
• A request for heat is sent from terminal 3 of connector X12 on the Control
Board (A10) to terminal 10 on connector X1 on the Hot Air Control Module
(N20)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control
Module (N20) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 12 of connector X15
on the Control Board (A10)
• The heat circuit will remain energized until the cabinet set temperature is
reached as sensed at probe B6.
When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is
sent from terminal 5 of connector X12 to the condenser valve (Y1) until the
temperature drops.
If the “Crisp and Tasty” mode is selected
• 120 VAC is sent from terminal 6 of connector X12 on the Control Board
(A10) to the Dehumidification Valve (Y2) to pull the humidity out of the
cabinet down the drain.
◊ In the light and medium modes (one and two drops in the display) the Y2
valve will be energized until the bypass probe (B5) is satisfied.
◊ In the full mode (3 drops in the display) the Y2 valve will be energized
continuously.
85
e
5
When the timer counts to 0 or the core temp probe (B10) reaches the set amount
the cycle .
With the combi in the Combi mode with time on the timer, the door closed and the
start switch is depressed
a The front display will include a lighted bar under the Combi symbol
• When the heat circuit is energized the heat symbol will be energized
• The cooking mode symbol will be energized.
• The time display will invert and begin to count down.
b The fan circuit is energized by the Control Board (A10) transmitting and
receiving a signal from terminals 5,6, and 7 on connector X10 to connector X12
on the Motor Drive Board (U10).
• The motor Drive Board sends a signal through the thermal switch in the motor
from Terminal 5 and receives on terminal 6
• If the thermal switch is not open the Motor Drive Board (U10) sends 240
VAC 3 phase to the motor.
• The motor reverses direction every 120 seconds with a 15 second coast.
c Hot air heat circuit is energized
• A signal is sent from terminal 8 of connector X15 on the Control Board (A10)
to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control
(U20) selecting the set speed of the combustion blower.
◊ When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 2 of
connector X15 on the Control Board (A10)
• A request for heat is sent from terminal 3 of connector X12 on the Control
Board (A10) to terminal 10 on connector X1 on the Hot Air Control Module
(N20)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control
Module (N20) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 12 of connector X15
on the Control Board (A10)
• The heat circuit will remain energized until the cabinet set temperature is
reached as sensed at probe B6.
d The steam circuit is energized.
• 120 VAC is sent from terminal 4 of connector X12 on the Control Board
(A10) to the coil of the Y3 solenoid allowing water to be thrown against the
element until the bypass probe (B5) senses 183 degrees F.
• The heat circuit will remain energized until the cabinet set temperature is
reached
• If the bypass probe (B5) drops below the set level the steam circuit will start
again.
86
e
5
When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is
sent from terminal 5 of connector X12 to the condenser valve (Y1) until the
temperature drops.
f If the “Crisp and Tasty” mode is selected
• 120 VAC is sent from terminal 6 of connector X12 on the Control Board
(A10) to the Dehumidification Valve (Y2) to pull the humidity out of the
cabinet down the drain.
◊ In the light and medium modes (one and two drops in the display) the Y2
valve will be energized until the bypass probe (B5) is satisfied.
◊ In the full mode (3 drops in the display) the Y2 valve will be energized
continuously.
g When the timer counts to 0 or the core temp probe (B10) reaches the set amount
the cycle ends and the steam generator reverts to the standby temperature of 190degree F.
With the combi in the Rethermalization mode with time on the timer, the door closed
and the start switch is depressed
a The front display will include a lighted bar under the Retherm symbol
• When the heat circuit is energized the heat symbol will be energized
• The cooking mode symbol will be energized.
• The time display will invert and begin to count down.
b The fan circuit is energized by the Control Board (A10) transmitting and
receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5
and 6 of connector X28 on the Gas Board (A20)
c The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the
Motor Drive.
• The motor Drive Board sends a signal through the thermal switch in the motor
from Terminal 5 and receives on terminal 6
• If the thermal switch is not open the Motor Drive Board (U10) sends 220
VAC 3 phase to the motor.
• The motor reverses direction every 120 seconds with a 15 second coast.
• NOTE: If the set temperature is less than 212 degrees F than fan will be
pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).
d Hot air heat circuit is energized
• A signal is sent from terminal 8 of connector X15 on the Control Board (A10)
to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control
(U20) selecting the set speed of the combustion blower.
◊ When this speed is attained the signal is sent from terminal 2 of connector
X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 2 of
connector X15 on the Control Board (A10)
• A request for heat is sent from terminal 3 of connector X12 on the Control
Board (A10) to terminal 10 on connector X1 on the Hot Air Control Module
(N20)
◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control
Module (N20) to the hot surface igniter (R20).
◊ The gas valve is energized allowing gas and air into the burner chamber to
be ignited by the hot surface igniter.
87
◊
e
f
g
h
The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps
DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a
signal from terminal 2 of connector X1 to terminal 12 of connector X15
on the Control Board (A10)
• The heat circuit will remain energized until the cabinet set temperature is
reached as sensed at probe B6.
The steam circuit is energized.
• 120 VAC is sent from terminal 4 of connector X12 on the Control Board
(A10) to the coil of the Y3 solenoid allowing water to be thrown against the
element until the bypass probe (B5) senses 183 degrees F.
• The heat circuit will remain energized until the cabinet set temperature is
reached
If the bypass probe (B5) drops below the set level the steam circuit will start again
When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is
sent from terminal 5 of connector X12 to the condenser valve (Y1) until the
temperature drops.
When the timer counts to 0 or the core temp probe (B10) reaches the set amount
the cycle ends and the steam generator reverts to the standby temperature of 190degree F.
88
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
CLEVELAND RANGE, LLC
1333 East 179th St., Cleveland, Ohio 44110-2574
TITLE
WIRING DIAGRAM
OGS 6.20/10.10
89
VOLTAGE:
WATTAGE:
CURRENT:
120VAC
10.25W
11.7A
DRAWN BY
DATE
DRL
8-9-05
DRAWING NO.
SIZE
B
REV
300494
A
SHEET 1 OF 6
1
2
3
4
5
BK 12
1333 East 179th St., Cleveland, Ohio 44110-2574
1
2
/3.B3
1
/3.B3
2
BU 18
BU 18
BK 18
/4.A6
/3.B5
-A10:X15:9
/3.B5
-A10:X15:11
-X10:42
COM
TxD
BU 18
OR
BN
TW/GY
TW/GY
RD 18
3
BN
3
BU 18
2
2
1
BK
1
RD 18
W1/BN
RD
8
8
7
7
3
3
9
SH
GND
-BM1
V1/BU
E
RPM
FAN
PRELIMINARY
VOLTAGE:
WATTAGE:
CURRENT:
WIRING DIAGRAM
OGS 6.20/10.10
4
90
-X13.6
/3.F1
TITLE
3
2
9
BK 18
6
6
BK 18
BK 18
4
5
5
/3.D4
4
-A10:X10:4
-A10:X10:3
-X10:21
-X13.5
U1/BK
M 3~
U2/RD
-M1
2
N
BU 18
RD 18
RD 18
-U10:X12:1
/A6
/3.D4
-X13.2
V2/WH
CLEVELAND RANGE, LLC
BK
-X10:101
W2/YE
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
C
D
-X13.1
F
L1 L2
U V W
GN 18
-W2
CABLE
E
RxD
BU 18
GND
/4.E5
0V
12V
L1 N
D
RD 18
RD 18
-G1
12V DC
GR
2
POWER SUPPLY
12VDC
96-264V
AC
3
1
MOTOR DRIVE
/3.D6
1
GND
GND
L
102
G
C
P1 P2
RD 18
-A10:X12:1
12V
-U10
RD 18
BU 18
-X10
B
31
1
BU 12
GR
-X10
20
RD 18
2
RD 18
N
GND
L
BK 12
-X10
-F10
15A
2A
LINE FILTER
-X10
/3.B3
1
L1
-F1.1
-Z1
B
-A10:X10:5
BU 12
-A10:X10:6
1
N1
BK 12
30
/E3
2
RD
4
-X10
-G1:12V
5
A
3
BK 12
6
8
WIRING DIAGRAM
BL 12
-A10:X10:7
-S1
7
BU 12
CONTROL POWER
A
6
DRAWN BY
120VAC
10.25W
11.7A
DATE
5
DRAWING NO.
DRL
SIZE
8-9-05
6
B
REV
300494
A
SHEET 2 OF 6
7
8
F
F
-X10:20
-X10
2
D5
D4
-A10:X10:11
RD
-A10:X10:12
-A10:X10:10
D4
-A10:X10:9
BK
/4.B4
/4.C4
BU
D4
RESET
RESET
10
9
8
7
6
PUMP/RINSE
4
COMPARTMENT RINSE VALVE
3
C
2
RD 18
-X10
RD 18
7
136
X13:
1
134
6
1
133
5
2
RD 18
4
3
ALARM GAS
3
4
5
D
A1
N
N
CLEANING AGENT
DEHUMIDIFICATION
VOLTAGE:
WATTAGE:
CURRENT:
WIRING DIAGRAM
OGS 6.20/10.10
4
91
N
RINSING AGENT
BU 18
TITLE
3
L
A2
A2
-Y20
E
-Y23
-Y22
WATER CLEANING
CONDENSER
L
-Y21
-Y3
L
RD 18
A1
CLEANING OPTION ONLY
-X10
FBS2-6
OVEN LAMP
1333 East 179th St., Cleveland, Ohio 44110-2574
-X10:41
/4.C4
2
5
ALARM GAS
DEHUMIDICATION/VALVE
1
6
PUMP/CLEANING AGENT
BU 18
CLEVELAND RANGE, LLC
-N20:X1:5
-N20:X1:11
RD 18
/4.B6
-U20:X2:2
PRES. SW
GND
FANE SPEED
RD 18
RD 18
GND
/4.A4
-A13:X1:4
-A13:X1:3
DOOR SW
X12:
8
WH
COM
N.O.
13
14
156
157
RD 18
GND
/2.C7
/2.C8
-X13.5:3
-X10:42
/2.C8
7
21
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
1
6
-X10:33
-Y1
A1
100
BU 18
FBS2-6
5
7
X14:
A2
X1
-H5.1
GND
X2
-M3.1
COOLING FAN
-X10
A2
-Y2
1~
4
8
A8
RD 18
A1
M
/2.F4
A8
A8
A8
/2.A6
/2.A6
/2.A6
/2.E3
-Y10
RD 18
2
RD
BK
1A
E
/2.E3
-G1:12V
-F2.1
3
10 9
CONDENSOR/VALVE
2
B
IDENTIFICATION MODULE
1
INJECTION
1
4
1
-X10:41
10 11 12
2
3
HEAT REQUEST
9
4
-A13
/4.B4
8
5
2 3
A
1
RD 18
-S2
OVEN LAMP
7
X11:
CABLE CONNECTION SM ON BM -W1
CONTROL 500
D
8
INJECTION
PRESSURE SWITCH
L1- 110/120
6
6
-X10:31
5
TxD
4
-U10:RxD
GND
RxD
3
-U10:TxD
0VDC IN
2
-U10:GND
12VDC IN
1
-G1:0V
12VDC FAN
1
12VDC FAN
X19:
7
/2.C4
X10:
CONTROL BOARD
/2.C7
/4.C3
X15:
8
PWM (HOT AIR)
SM 5010
-X13.5:1
-N20:X1:2
GN/BU
14 13 12 11 10 9
1
2
3
MOTOR SPEED (M1)
4
PRES. SW
KTM
CTC
GN
-B10
5
GN/RD
GN
GN
6
X16:
C
14
PROBE OVEN
-B6
7
IDM (RD)
X18:
WH
YL
8
X17:
1
13
PROBE BYPASS
-B5
RD
12 11 10 9
GND (M1 H.E. SENSOR)
1
+12VDC
2
3
FLAME OK (HOT AIR)
4
IDM (BU)
5
IDM (WH)
6
-X10
-A13:X1:2
7
7
CLEANING OPTION ONLY
IDM (BK)
-A10
8
-S7
-S2
CLEANING PRESSURE SWITCH
-A13:X1:1
10 9
YL
X39: 1
-A12
RD
B
PROBE CONDENSER
PICTO
MODULE
6
DOOR MAGNET SWITCH
-B3
BM 5010
OPERATION BOARD
5
BURNER SUPPLY
WIRING DIAGRAM
-A11
(OPTION)
4
-U20:X2:4
3
RD
A
2
YL
1
22
-X10:23
INJECTION
DRAWN BY
120VAC
10.25W
11.7A
DATE
5
DRAWING NO.
DRL
SIZE
8-9-05
6
B
300494
CLEANING AGENT
FBS2-6
/4.A1
PRELIMINARY A
REV
SHEET 3 OF 6
7
8
F
4
5
WIRING DIAGRAM
-A10:X11:8
A
(BURNER SUPPLY / 120V)
RD 18
GND
101
2
X3:
-A10:X15:8
RD 18
RD 18
1
3
4
5
X2:
D
1
GN 18
/2.C5
E
2
1
-U10:GND
-R20
X1:
3
GN 18
-X10
FLAME SENSOR
HOT SURFACE IGNITION
(HOT AIR)
2
1
RD 18
-P1
1
PWM CONVECTION 1
X2:
2
/3.A6
/3.A6
-A10:X15:2
BURNER FAN
(HOT AIR)
SPEED CONVECTION 1
-U20
11 12
GN 18
BU 18
-A10:X14:3
RD 18
9 10
BU 18
/3.D6
(RESET AIR HEAT)
/3.A7
RD 18
7 8
GROUND CONVECTION 1
6
B
42
C
X1:
3
E
-A10:X12:3
22
/3.A7
(HI-LIMIT)
-A10:X14:2
(RESET CONV. 1 (HL1)
5
RD 18
RD 18
4
BURNER CONTROL
(HOT AIR)
60
-A10:X14:1
(HI-LIMIT)
(NEUTRAL)
/3.A7
3
-X10
GND
2
RD 18
1
-X10 41
RD 18
-N20
BU 18
RD 16
RD 18
BU 18
RD 16
BU 18
24 VAC
21
-B7.1
-A10:X15:12
(GND)
(FLAMECHECK)
/3.B5
-X10:42
-T1
BU 18
BU 16
BK 16
OR 16
WH 16
120VAC
A7
B
61
/3.B5
-X13:5:2
RD 18
BU 18
STB
OVER TEMPERATURE THERMOSTAT
(HOT AIR)
-X10
33
C3
-X10
D
8
-N20:X1:1
/3.D6
/2.C7
-X10:22
A
7
-A10:X15:10
23
C
6
RD 18
-X10
3
L1
/3.F8
2
N
1
BU 18
F
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
CLEVELAND RANGE, LLC
1333 East 179th St., Cleveland, Ohio 44110-2574
1
2
TITLE
VOLTAGE:
WATTAGE:
CURRENT:
WIRING DIAGRAM
OGS 6.20/10.10
3
4
92
DRAWN BY
120VAC
10.25W
11.7A
DATE
5
DRAWING NO.
DRL
SIZE
8-9-05
6
B
300494
PRELIMINARY
SHEET 4 OF 6
7
8
REV
A
F
1
2
3
4
5
6
7
8
A
A
/6.A6
-A10:X15:2
/6.B5
B
-A10:X15:9
2
1
GND
NEUTRAL
TxD
3
3
RECIEVE
RxD
2
4
TRANSMIT
12V
1
Hi-Limit
Hi-Limit
X11:
3
2
L
12
PE N
C
3
4
5 4
GND
6
1
RESET AIR HEAT/GO
1
RESET AIR HEAT
D
15A
PHASE ( L1 )
8 7
X12:
LINE FILTER
L1
2A
12
0
12VDC
GND
E
N
N
POWER SUPPLY
12VDC
RD
E
2
X10:
LADDER DIAGRAM
D
3
PTC PTC W V U PE
12 11 10 9
6 5 4
C
1
FAN
90-264VAC
-A10:X15:11
B
-A10:X15:8
SCH
IRM
/6.B5
/6.B5
F
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
CLEVELAND RANGE, LLC
1333 East 179th St., Cleveland, Ohio 44110-2574
1
2
TITLE
VOLTAGE:
WATTAGE:
CURRENT:
WIRING DIAGRAM
OGS 6.20/10.10
3
4
93
DRAWN BY
120VAC
10.25W
11.7A
DATE
5
DRAWING NO.
DRL
SIZE
8-9-05
6
B
300494
PRELIMINARY
SHEET 5 OF 6
7
8
REV
A
F
N
F
1
THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.
THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.
CLEVELAND RANGE, LLC
1333 East 179th St., Cleveland, Ohio 44110-2574
2
3
94
3
4
5
6
TITLE
WIRING DIAGRAM
OGS 6.20/10.10
4
7
VOLTAGE:
WATTAGE:
CURRENT:
1
2
3
4
120VAC
10.25W
11.7A
5
5
6
7
8
DRAWN BY
DATE
DRL
8-9-05
6
2
3
4
SIZE
5
DRAWING NO.
B
10 9
7
8
9
10
300494
7
7
6
5
4
3
2
1
ALARM GAS
6
8
ALARM GAS
-N20:X1:10
/5.D8
/5.C8
/5.D8
CLEANING OPTION ONLY
-N20:X1:5
-N20:X1:11
/5.A4
13
N.O.
COM
13
7
4
LADDER DIAGRAM
1
RESET
X14:
-U20:X2:2
14
6
RESET
PUMP / CLEAN AGENT
X13:
PUMP / RINSE
1
COMPARTMENT RINSE V.
FAN SPEED
5VDC
2
L2
5VDC
3
FREE
4
L1
5
0VDC
6
0VDC
7
STEAM GEN OVER TEMP
8
5VDC
/2.C8
/5.B1
/5.A8
/5.B1
/5.C8
KTM
CTC
-B10
-X10
-U20:X2:4
-BM1:BN
-N20:X1:1
-BM1:RD
-N20:X1:2
GNBU
-S2
BURNER SUPPLY
14 13 12 11 10 9
PWM (HOT AIR)
0VDC
1
MOTOR SPEED (M1)
2
GND
3
+12VDC
4
GNRD
GN
GN
GN
PROBE OVEN
PROBE BYPASS
PROBE CONDENSER
CLEANING PRESSURE SWITCH
FREE
X15:
5
X11:
DEHUMIDICATION/VALVE
6
FLAME OK (HOT AIR)
CONDENSOR/VALVE
-B6
-B5
-B3
-S7
-Y23
2
INJECTION
7
5
-Y22
1
WH
GN
WH
GN
WH
GN
WH
DOOR MAGNET SWITCH
-Y21
HEAT REQUEST
8
X12:
OVEN LAMP
X16:
(OPTION)
MODULE
PICTO
-A12
OPERATION MODULE
4
/5.D8
2 3
-N20:X1:10
1
/5.D8
10 11 12
1
9
L1- 110/120 VAC-INPUT
12 11 10 9
-N20:X1:12
BURNER CONTROL
-Y4
8
2
7
IDM (R)
1
-F2.1
6
IDM (BL)
X39: 1
-A11
BM 5010
3
-Y20
E
X1
5
IDM (W)
2
-A13
3
IDM (BLK)
4
I.D. MODULE
TxD_12V
4
RESET
3
5
-U10:X12:2
2
6
/5.C4
1
X10:
0VDC IN
X17:
7
GND
12VDC IN
X18:
8
RxD_12V
12VDC FAN (+)
X19:
10 9
-U10:X12:3
12VDC FAN (-)
1
-U10:X12:4
M
1
/5.C4
/5.C4
-M3.1
D
-A10
SM 5010
C
CONTROL BOARD
B
-Y1
X2
L1
A
2
-Y2
-H5.1
12
12VDC
0
1
8
INJECTION
PRESSURE SWITCH
-S2
A
B
PRELIMINARY
SHEET 6 OF 6
8
REV
A
C
D
E
F