Download 160 SSC™ Variable Speed Drive (Series C)

160 SSC™
Variable Speed
Drive (Series C)
Publication 160-CDP
Configured Drive Package
Important User Information
Solid state equipment has operational characteristics differing from those of
electromechanical equipment. “ Safety Guidelines for the Application,
Installation and Maintenance of Solid State Controls” (Publication SGI-1.1
available from your local Allen-Bradley Sales Office or online at http://
www.ab.com/manuals/gi) describes some important differences between
solid state equipment and hard-wired electromechanical devices. Because
of this difference, and also because of the wide variety of uses for solid state
equipment, all persons responsible for applying this equipment must satisfy
themselves that each intended application of this equipment is acceptable.
In no event will the Allen-Bradley Company be responsible or liable for
indirect or consequential damages resulting from the use or application of
this equipment.
The examples and diagrams in this manual are included solely for
illustrative purposes. Because of the many variables and requirements
associated with any particular installation, the Allen-Bradley Company
cannot assume responsibility or liability for actual use based on the
examples and diagrams.
No patent liability is assumed by Allen-Bradley Company with respect to
use of information, circuits, equipment, or software described in this
manual.
Reproduction of the contents of this manual, in whole or in part, without
written permission of the Allen-Bradley Company is prohibited.
Throughout this manual we use notes to make you aware of safety
considerations.
!
ATTENTION: Identifies information about practices or
circumstances that can lead to personal injury or death, property
damage, or economic loss.
Attentions help you:
• identify a hazard
• avoid the hazard
• recognize the consequences
Important: Identifies information that is especially important for successful
application and understanding of the product.
Shock Hazard labels may be located on or inside the drive to
alert people that dangerous voltage may be present.
SCANport is a trademark of Rockwell Automation.
PLC is a registered trademark of Rockwell Automation.
COLOR-KEYED is a registered trademark of Thomas & Betts Corporation.
IBM is a registered trademark of International Business Machines Corporation.
Windows 95 is a registered trademark of Microsoft Corporation.
Bulletin 160 SSC™ Variable Speed Controller Configured Drives Package
Thank you for purchasing a Bulletin 160 Configured Drive. This Rockwell Automation
product is designed with the customer in mind, saving time and money by configuring
a drive package at the factory to meet your application needs.
This publication contains all drawings for the Bulletin 160 Configured Drive product
offering. To select the appropriate schematics for the Configured Drive you have
purchased, obtain the complete catalog string from the unit’s data nameplate. Note the
options specified in the catalog string and refer to the page number that corresponds
with each option.
Compliance Certification (applicable to approved program defined options)
U.S./Canada UL:
CUL:
UL508C
CAN/CSA-C22.2 No. 14-M91
Europe
CE:
Low Voltage Directive – EN60204-1, EN50178
EMC Directive – EN61800-3, EN500082-2, EN50081-2
Australia
C-Tick:
AS/NZS 2064.1
CE Compliance
CE Marking of this product is based upon compliance with the Low Voltage Directive
73/23/EEC and the EMC Directive 89/336/EEC. The following standards have been
used to demonstrate compliance with the directives:
Low Voltage Directive
EN60204-1
EN50178
EMC Directive
EN61800-3
EN50081-2
EN50082-2
Important:
This product complies with the EMC requirements of EN61800-3 and other referenced
EMC standards as a stand-alone unit. It is the responsibility of the machine builder
applying this product in machinery to ensure EMC compliance of the entire installation.
Refer to the Bulletin 0160 User Manual for additional information.
A copy of the Declaration of Conformity (DoC) is available from your local Rockwell
Automation Sales Office.
3
Table of Contents
Data Nameplate Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
(Use for all catalog numbers.)
Standard Control Interface for
Analog Signal Follower and Preset Speed Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
(Use when drive catalog number does not include control interface options
DMSF1C, DMPS1C, or LTN120.)
Twenty-Four Volt DC (24VDC) Control Interface for
Analog Signal Follower and Preset Speed Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
(Use when drive catalog number includes control interface options DMSF1C or
DMPS1C.)
One Hundred Twenty Volt AC (120VAC) Control Interface for
Analog Signal Follower and Preset Speed Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
(Use when drive catalog number includes drive option SF1 and
control interface option LTN120.)
Material List for Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
4
Data Nameplate Drawing
A
B
C
D
E
F
G
H
1
1
2
2
186954
186953
3
DATA NA
CAT.
NO.
4
-SERIES C
SER.
NO.
5
3
DATA NAMEPLATE
CAT.
NO.
SEE NOTE 2
SEE NOTE 2
4
-SERIES C
SER.
NO.
SEE NOTE 3
H.P.
H.P.
TABLE 2
ENCLOSURE TYPE
ENCLOSURE TYPE
SEE NOTE 3
5
1S
FACILITY
6
6
POWER RATIN
POWER RATINGS
NOTE 1
TE 1
7
8
TABLE 1
KVA
TABLE 2
KVA
TABLE 1
VOLTS
TABLE 1
VOLTS
TABLE 2
VOLTS
50/60
Hz
0-240
Hz
50/60
Hz
AMPS
9
100,000
7
0-240
8
Hz
AMPS
9
AMPS
10
10
11
11
12
12
13
13
14
14
TABLE 1
15
15
SINGLE PHASE
16
DRIVE RATINGS
17
18
19
16
CATALOG NO.
H.P.
INPUT
KVA
INPUT
VOLTS
INPUT
AMPS
OUTPUT
KVA
OUTPUT
VOLTS
OUTPUT
AMPS
160S-AA02*
160S-AA03*
160S-AA04*
160S-AA08*
.5
.75
1
2
1.1
1.4
2.2
3.7
230
230
230
230
4.8
6.2
9.4
16.3
0.5
0.7
1.0
1.8
230
230
230
230
2.3
3.0
4.5
8.0
17
18
19
20
20
22
22
23
TABLE 2
23
24
THREE PHASE
24
DRIVE RATINGS
25
25
26
27
28
29
30
31
32
CATALOG NO.
H.P.
INPUT
KVA
INPUT
VOLTS
INPUT
AMPS
OUTPUT
KVA
OUTPUT
VOLTS
OUTPUT
AMPS
160-AA02*
160-AA03*
160-AA04*
160-AA08*
160-AA12*
160-AA18*
.5
.75
1
2
3
5
1.1
1.4
2.2
3.7
5.7
8.4
230
230
230
230
230
230
2.8
3.6
5.4
9.4
14.2
21.1
1.0
1.2
1.9
3.3
5.0
7.2
230
230
230
230
230
230
2.3
3.0
4.5
8.0
12.0
18.0
160-BA01*
160-BA02*
160-BA03*
160-BA04*
160-BA06*
160-BA10*
.5
.75
1
2
3
5
1.1
1.6
2.2
3.7
5.6
9.7
460
460
460
460
460
460
1.4
2.0
2.8
4.6
7.0
12.2
1.0
1.3
1.8
3.2
4.8
8.4
460
460
460
460
460
460
1.2
1.7
2.3
4.0
6.0
10.5
26
27
28
29
30
31
32
* - CATALOG SUFFIX MUST CONTAIN "SF1" OR "PS1".
33
33
NOTES:
34
34
1.) CE AND C-TICK LABELS CAN NOT BE USED WITH OPTION LTN120.
2.) ASSIGN CATALOG NUMBER PER THE ITEM DESCRIPTION.
3.) TO ASSIGN SERIAL NUMBER USE PARENT ITEM NUMBER FOLLOWED BY A (-1), (-2), ETC.
DEPENDING ON QUANTITY OF ORDER ITEM.
35
36
35
36
4.) ENCLOSURE TYPE IS DICTATED BY 2 DIGITS OF THE DRIVE CATALOG NUMBER.
a.) "AF" = TYPE 4
b.) "AS" = TYPE 4X
37
37
5.) KVA AND CURRENT RATINGS ARE BASED ON A NOMINAL VOLTAGE OF 230V AND 460V RESPECTIVELY.
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
5
Standard Control Interface
Power Distribution and DS Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operator Interface Options DN2C, RS1C, P1C, RPAC, P2C, and
Ready/Fault Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Enclosure Mounted DeviceNet Connector Options: DNSC1, DNSC2,
DNBC1, DNBC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Drive Ratings and DS Option Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Product Control Logic Options
D13 Without P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
D13 With P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
D17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
D32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
D33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
D13 and D32 Without P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
D13 and D32 With P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
D17 and D32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
D32 and D33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
D35 and D36 Without Keypad or Comm Control Options. . . . . . . . . . . . . . . . . . . . . . . . . . 18
D35 and D36 With Keypad or Comm Control Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
D61 for Analog Signal Follower Drives Without Keypad or Comm Control Options . . . . . 20
D61 for Analog Signal Follower Drives With Keypad or Comm Control Options . . . . . . . 21
MX12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
MX14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 and 23
P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
MX19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6
Power Distribution and DS Option
A
B
C
D
E
F
G
H
1
1
BRAKE
1C
2
2
L2
*
1PH, 50/60HZ
AC LINES
3
4
L1
5
1
DISCONNECTING
D
MEANS AND
SHORT CIRCUIT
PROTECTION
PROVIDED BY
OTHERS
WHEN DS OPTION
IS NOT ORDERED
L2
6
3PH, 50/60HZ
AC LINES
7
3
L3
17-18
17-37
L3
4
4
LINE FILTER
2
5
MX14 OPTION
5
6
MODULE
3
6
7
LINE
PE
8
8
POWER DISCONNECTING OPTION
9
9
DS OPTION
10
10
CHASSIS
EA1
GRD
11
R
S
T
(STD)
READY/FAULT PANEL
(OPTIONAL)
RS1C RS232 SERIAL COM
13
1
L2
F2
2
L3
F3
3
12
TERMINAL BLOCK TB2
(INTERFACE CONTROL BOARD)
FOR DETAILED INFORMATION,
REFER TO CONTROL OPTIONS
P2C REMOTE KEYPAD MODULE
DN2C DEVICE NET PANEL
RS1C RS232 SERIAL COM
PD1C PROFIBUS MODULE
IB1C INTERBUS MODULE
14
F1
11
EA2
12
L1
13
TABLE 1
600V
14
DS1
15
15
DN2 DEVICE NET PANEL
BLK
16
BLU
CUSTOMER
DEVICE-NET
CONNECTION
17
18
OPTIONS
20
LINE FILTER OPTION
EMC OPTION
3
WHT
17
4
RED
5
RF1
1
30
31
OPTIONAL
DNSC1
DNSC2
DNBC1
DNBC2
16
2
GRAY
5-PIN CONNECTOR
19
1
2
TO
3
17-38
L1
L1'
MODULE
L2
L2'
TABLE 1
L3
L3'
4
18
5
19
6
20
MX14 OPTION
BULLETIN 160 SMART SPEED CONTROLLER
22
23
TABLE 1 . HP
ANALOG SIGNAL FOLLOWER/PRESET SPEED MODEL
TABLE 1 VOLTS
FOR FURTHER DRIVE INFORMATION, REFER TO
TABLE 1 AMPS
160 SSC™ VARIABLE SPEED DRIVE USER MANUAL
22
23
24
24
NOTE: MOTOR FLA MUST NOT
EXCEED DRIVE AMP RATING.
TERMINAL BLOCK TB2
25
BR+
26
BR-
+DC
-DC
GRD
U
V
25
W
26
27
27
OPERATOR INTERFACE
MODULE
28
29
PROGRAM
RUN
ESC
30
FORWARD
28
29
REVERSE
SEL
30
31
31
MOTOR DATA
32
32
HP
VOLTS
33
(T2)
OPTIONAL
P2C
(T1)
(T3)
(G)
34
33
FLA
AC
MOTOR *
RPM (BASE)
34
REFER TO MOTOR NAMEPLATE
FOR EXACT DATA.
35
GENERAL NOTES:
REV. STATUS
OF SHEETS
36
37
38
35
4. COIL AND CONTACT CROSS REFERENCING - NUMBERS ADJACENT TO
36
- BUILDING GROUND TO BE GROUNDED
BY CUSTOMER.
TE
PE
37
- SIGNAL COMMON
1-3
CATES SHEET NO. 1.
DERSCORED TEXT LINE INDICATES
ORMALLY CLOSED CONTACT.
- CHASSIS CONNECTION.
39
2. * -INDICATES COMPONENTS SUPPLIED BY OTHERS.
-INDICATES TB4 TERMINAL BLOCK.
3.
4
39
OFF-PAGE CROSS REFERENCING - NUMBERS ADJACENT TO SOURCE
40
41
38
- POWER EQUIPMENT GROUND
40
FROM
M 1-24
41
-INDICATES TERMINAL ON INDIVIDUAL
COMPONENTS.
TO 1-24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
7
-INDICATES SHEET NO. 1.
Drive Ratings and DS Option Ratings
A
B
C
D
E
F
G
H
1
1
TABLE 1
2
2
SINGLE PHASE
3
DRIVE RATINGS
CATALOG NO. (HP)
VOLTAGE
4
160S-AA02* (.5)
160S-AA03* (.75)
160S-AA04* (1)
160S-AA08* (2)
6
LINE FILTER MODULE
FLA
TYPE
5
3
FUSE RATINGS (DS OPTION)
200-240V
200-240V
200-240V
200-240V
2.3A
3.0A
4.5A
8.0A
LPJ
LPJ
LPJ
LPJ
AMP
VOLT
6A
10A
15A
30A
600V
600V
600V
600V
4
CATALOG NUMBER
5
160S-RFA-9-A
160S-RFA-9-A
160S-RFA-9-A
160S-RFA-16-B
6
7
7
THREE PHASE
8
9
CATALOG NO.
(HP)
10
11
12
13
14
15
DRIVE RATINGS
VOLTAGE
8
FUSE RATINGS (DS OPTION)
TYPE
9
LINE FILTER MODULE
FLA
CATALOG NUMBER
AMP
VOLT
160-AA02* (.5)
160-AA03* (.75)
160-AA04* (1)
160-AA08* (2)
160-AA12* (3)
160-AA18* (5)
200-240V
200-240V
200-240V
200-240V
200-240V
200-240V
2.3A
3.0A
4.5A
8.0A
12.0A
18.0A
LPJ
LPJ
LPJ
LPJ
LPJ
LPJ
6A
6A
10A
15A
20A
30A
600V
600V
600V
600V
600V
600V
160-RFB-5-A
160-RFB-5-A
160-RFB-5-A
160-RFB-14-A
160-RFB-14-A
160-RFB-22-B
160-BA01* (.5)
160-BA02* (.75)
160-BA03* (1)
160-BA04* (2)
160-BA06* (3)
160-BA10* (5)
380-460V
380-460V
380-460V
380-460V
380-460V
380-460V
1.2A
1.7A
2.3A
4.0A
6.0A
10.5A
LPJ
LPJ
LPJ
LPJ
LPJ
LPJ
4A
4A
5A
8A
15A
20A
600V
600V
600V
600V
600V
600V
160-RFB-5-A
160-RFB-5-A
160-RFB-5-A
160-RFB-5-A
160-RFB-14-A
160-RFB-14-B
10
11
12
13
14
15
16
16
* - CATALOG NO. SUFFIX CAN CONTAIN "SF1" OR "PS1"
17
17
18
18
19
19
20
20
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
8
D13 Without P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
OFF
5
RUN REVERSE
6
RUN FORWARD
10
HAND
11
20 (1)
(XOO)
12
(2)
SLOT-1
11
21
R
12
13
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
13
SLOT-2
14
(4)
(3)
(OOX)
15
14
22
R
SS2
15
9
16
16
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
27
27
28
28
TERMINAL BLOCK TB3
29
OFF
HAND
30
20
(1)
(XOO)
31
5
RUN REVERSE
6
RUN FORWARD
29
AUTO
(2)
SLOT-1
30
21
R
31
32
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
32
SLOT-2
33
(4)
(OOX)
34
(3)
SS2
33
22
R
34
9
35
35
36
37
11
38
36
PROGRAMMABLE RELAY
OUTPUTS
10
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
9
D13 With P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
OFF
HAND
11
20 (4)
(OOX)
12
AUTO
RUN REVERSE
6
RUN FORWARD
11
(3)
SLOT-2
10
5
2-WIRE
DEVICE
R
12
*
13
13
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-1
14
(1)
(2)
(XOO)
15
14
22
R
SS2
15
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
27
27
28
28
TERMINAL BLOCK TB3
29
OFF
HAND
30
20
SLOT-2
5
RUN REVERSE
6
RUN FORWARD
29
2-WIRE
DEVICE
30
(3)
(4)
(OOX)
31
AUTO
R
31
*
32
32
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-1
33
(1)
(XOO)
34
(2)
33
22
R
SS2
34
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
38
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
10
D17
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
5
REVERSE
6
START
10
START
11
20
(3)
(4)
12
11
21
R
PB2
12
SLOT-1
13
7
COMMON
8
STOP
13
STOP
14
(1)
(2)
14
22
R
PB3
15
15
SLOT-1
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
27
27
28
28
TERMINAL BLOCK TB3
29
5
REVERSE
6
START
29
START
30
20
(3)
(4)
PB2
31
30
21
R
31
SLOT-1
32
7
COMMON
8
STOP
32
STOP
33
(1)
(2)
34
33
22
R
PB3
34
SLOT-1
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
38
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
11
D32
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
FORWARD
10
(OX)
START
11
20
SS3
9
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
R
5
REVERSE
6
START
10
SLOT-2
11
21
*
12
12
13
7
COMMON
8
STOP
13
STOP
14
14
22
*
15
15
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
5
REVERSE
6
START
27
27
28
FORWARD
(OX)
START
30
20
SS3
28
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
29
R
29
SLOT-2
30
21
*
31
31
32
33
STOP
34
*
7
COMMON
8
STOP
32
33
22
34
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
11
38
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
12
D33
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
10
5
RUN REVERSE
6
RUN FORWARD
2-WIRE
DEVICE
11
12
11
12
*
13
LOCAL
20 (3)
(OX)
14
15
REMOTE
(4) 22
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
R
SS1
13
7
15
SLOT-1
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
5
RUN REVERSE
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
29
2-WIRE
DEVICE
30
31
30
31
*
32
LOCAL
20 (3)
(OX)
33
34
REMOTE
(4) 22
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
R
SS1
32
7
34
SLOT-1
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
38
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
13
D13 and D32 Without P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
+10V POT
5
2
WIPER/0-10VDC INPUT
6
3
COMMON
7
4
4-20mA INPUT
5
1
6
7
8
8
OFF
9
HAND
AUTO
FORWARD
20
10
(1)
(XOO)
(2)
SLOT-1
21
R
(OX)
R
9
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
10
5
RUN REVERSE
6
RUN FORWARD
SLOT-2
11
(1)
(2)
SS3
(XO)
12
11
24
R
12
SLOT-1
13
13
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
14
15
(4)
(3)
(OOX)
R
SS2
14
22
15
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
5
RUN REVERSE
6
RUN FORWARD
27
27
OFF
28
HAND
AUTO
FORWARD
20
29
(1)
(XOO)
(2)
SLOT-1
21
R
(OX)
R
28
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
29
SLOT-2
30
(1)
(XO)
31
(2)
SS3
30
24
R
31
SLOT-1
32
32
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
33
(4)
(OOX)
34
(3)
33
22
R
SS2
34
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
38
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
14
D13 and D32 With P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
AUTO CONTROL
OFF
9
HAND
20
10
AUTO
(4)
(OOX)
SLOT-1
2-WIRE
DEVICE
21
(3)
R
*
11
(1)
(XO)
12
(2)
SS3
9
TERMINAL BLOCK TB3
FORWARD
REVERSE
23 (3)
(4) 24
R
(OX)
SLOT-2
10
5
RUN REVERSE
6
RUN FORWARD
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
11
25
R
12
SLOT-1
13
13
SLOT-2
14
15
(1)
(2)
(XOO)
R
SS2
14
22
15
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
27
27
AUTO CONTROL
OFF
HAND
28
20
29
AUTO
(4)
(OOX)
(3)
SLOT-1
2-WIRE
DEVICE
21
R
*
30
(1)
(XO)
31
(2)
SS3
28
TERMINAL BLOCK TB3
FORWARD
REVERSE
23 (3)
(4) 24
R
(OX)
SLOT-2
5
RUN REVERSE
6
RUN FORWARD
29
30
25
R
31
SLOT-1
32
32
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
33
(1)
(XOO)
34
(2)
SS2
33
22
R
34
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
38
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
15
D17 and D32
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
FORWARD
10
(OX)
START
11
20
(3)
SS3
9
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
R
5
REVERSE
6
START
10
SLOT-2
(4)
11
21
PB2
12
12
SLOT-1
13
7
COMMON
8
STOP
13
STOP
14
(1)
(2)
14
22
PB3
15
15
SLOT-1
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
5
REVERSE
6
START
27
27
28
FORWARD
(OX)
START
30
20
(3)
SS3
28
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
29
R
29
SLOT-2
(4)
30
21
PB2
31
31
SLOT-1
32
7
COMMON
8
STOP
32
STOP
33
(1)
(2)
33
22
PB3
34
34
SLOT-1
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
38
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
16
D32 and D33
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
2-WIRE
DEVICE
FORWARD
21
10
R
(OX)
9
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
10
5
RUN REVERSE
6
RUN FORWARD
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
*
11
(1)
(2)
SS3
(XO)
12
11
24
R
12
SLOT-1
13
LOCAL
20 (3)
(OX)
14
15
REMOTE
(4) 22
14
R
SS1
13
15
SLOT-1
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
27
27
28
2-WIRE
DEVICE
FORWARD
21
29
(3)
R
(OX)
28
TERMINAL BLOCK TB3
REVERSE
(4) 23
5
RUN REVERSE
6
RUN FORWARD
29
SLOT-2
*
30
(1)
(XO)
31
(2)
SS3
30
24
R
31
SLOT-1
32
LOCAL
20 (3)
(OX)
33
34
REMOTE
(4) 22
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
R
SS1
32
7
34
SLOT-1
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
38
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
17
D35 and D36 Without Keypad or Comm Control Options
A
B
C
D
E
F
G
H
1
1
2
2
TABLE 2
3
OPTION
SYMBOL
COLOR
LEGEND
PAR 47 SETTING
4
D35
D36
PL3
PL4
WHITE
RED
DRIVE RUN
DRIVE FAULT
2
0 (DEFAULT)
3
ANALOG SIGNAL FOLLOWER
4
160
CONTROL BOARD
TB3
+10V POT
5
2
WIPER/0-10VDC INPUT
6
3
COMMON
7
4
4-20mA INPUT
5
1
6
7
8
8
9
9
TERMINAL BLOCK TB3
10
5
REVERSE
6
START
10
START
11
20
11
21
*
12
12
13
7
COMMON
8
STOP
13
STOP
14
14
22
*
15
15
16
16
9
CUST.
SUPPLIED
120VAC
17
PILOT DEVICE
25
(X2)
18
17
PROGRAMMABLE RELAY
OUTPUTS
10
(X1)
SEE TABLE 2
19
11
INPUT MODE 0
18
(PAR 46 = 0)
19
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
5
REVERSE
6
START
27
27
28
28
TERMINAL BLOCK TB3
29
29
START
30
20
30
21
*
31
31
32
33
STOP
34
*
7
COMMON
8
STOP
32
33
22
34
35
35
9
CUST.
SUPPLIED
120VAC
36
PILOT DEVICE
25
(X2)
37
36
PROGRAMMABLE RELAY
OUTPUTS
10
(X1)
SEE TABLE 2
38
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
18
D35 and D36 With Keypad or Comm Control Options
A
B
C
D
E
F
G
H
1
1
2
2
TABLE 2
3
OPTION
SYMBOL
COLOR
LEGEND
PAR 47 SETTING
4
D35
D36
PL3
PL4
WHITE
RED
DRIVE RUN
DRIVE FAULT
2
0 (DEFAULT)
3
ANALOG SIGNAL FOLLOWER
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
OFF
HAND
AUTO
10
5
RUN REVERSE
6
RUN FORWARD
2-WIRE
DEVICE
11
12
11
12
*
13
13
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
14
*
15
15
NOTE 1
16
16
9
CUST.
SUPPLIED
120VAC
17
PILOT DEVICE
25
(X2)
18
17
PROGRAMMABLE RELAY
OUTPUTS
10
(X1)
SEE TABLE 2
19
11
INPUT MODE 6
18
(PAR 46 = 6)
19
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
5
RUN REVERSE
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
OFF
HAND
AUTO
29
2-WIRE
DEVICE
30
31
30
31
*
32
32
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
33
*
34
34
NOTE 1
35
35
9
CUST.
SUPPLIED
120VAC
36
PILOT DEVICE
25
(X2)
37
36
PROGRAMMABLE RELAY
OUTPUTS
10
(X1)
SEE TABLE 2
38
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
NOTE 1:
40
40
WIRE TB3-7 TO TB3-8 IF OPTIONS D13, D33 OR MX12 ARE NOT ORDERED.
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
19
41
D61 for Analog Signal Follower Drives Without Keypad or Comm Control Options
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
5
SPEED
REF.
RH1
10K
6
RED
WHITE
7
SHLD
4
160
CONTROL BOARD
TB3
BLACK
1
+10V POT
5
2
WIPER/0-10VDC INPUT
6
3
COMMON
7
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
5
REVERSE
6
START
10
START
11
20
11
21
*
12
12
13
7
COMMON
8
STOP
13
STOP
14
14
22
*
15
15
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
20
20
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
20
D61 for Analog Signal Follower Drives With Keypad or Comm Control Options
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
5
SPEED
REF.
RH1
10K
6
WHITE
7
+10V POT
5
2
WIPER/0-10VDC INPUT
6
3
COMMON
7
4
4-20mA INPUT
1
RED
SHLD
4
160
CONTROL BOARD
TB3
BLACK
8
8
9
9
TERMINAL BLOCK TB3
10
OFF
HAND
AUTO
10
5
RUN REVERSE
6
RUN FORWARD
2-WIRE
DEVICE
11
12
11
12
*
13
13
7
COMMON
8
TBE/KEYPAD OR COMMUNICATION CONTROL
14
14
*
15
15
NOTE 1
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
20
20
22
22
23
23
24
24
25
25
26
26
27
27
28
28
NOTE 1:
29
29
WIRE TB3-7 TO TB3-8 IF OPTIONS D13, D33 OR MX12 ARE NOT ORDERED.
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
21
MX12
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
LOCAL CONTROL
OFF
RUN FWD
20 (B)A1
21
(B)A2
R
(OX)
SS2
11
12
LOCAL
20
SS1
15
6
RUN FORWARD
12
REMOTE
22
(B)A2
(B)A1
(OX)
RUN REVERSE
11
13
14
10
5
13
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
R
15
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
5
RUN REVERSE
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
29
LOCAL CONTROL
OFF
30
20
RUN FWD
21
(B)A2
(B)A1
(OX)
SS2
31
30
R
31
32
LOCAL
33
20
REMOTE
22
(B)A2
(B)A1
(OX)
34
SS1
32
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
R
34
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
38
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
22
MX14
A
B
C
D
E
F
G
H
1
1
2
ANALOG SIGNAL FOLLOWER
2
3
160
CONTROL BOARD
3
TB3
4
5
6
7
1
+10V POT
2
WIPER/0-10VDC INPUT
3
COMMON
4
4-20mA INPUT
5
RUN REVERSE
6
RUN FORWARD
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
4
5
6
8
7
8
TERMINAL BLOCK TB3
9
9
2-WIRE
DEVICE
10
10
*
11
11
12
LOCAL
13
(OX)
12
REMOTE
13
*
NOTE 1
14
14
9
15
16
31
FROM
1-19
24VDC
17
15
16
PROGRAMMABLE RELAY
OUTPUTS
10
INPUT MODE 6
1C
32
30
18
A2
17
(PAR 46 = 6)
11
18
–
19
19
MX14 OPTION
20
20
PRESET SPEED MODEL
22
160
CONTROL BOARD
TB3
23
24
25
26
22
1
SW1
2
SW2
3
COMMON
4
SW3
5
RUN REVERSE
6
RUN FORWARD
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
23
24
25
26
27
27
TERMINAL BLOCK TB3
28
28
2-WIRE
DEVICE
29
29
*
30
30
31
31
REMOTE
32
(OX)
32
*
NOTE 1
33
33
9
34
35
31
FROM
1-19
24VDC
36
34
35
PROGRAMMABLE RELAY
OUTPUTS
10
INPUT MODE 6
1C
30
32
37
36
(PAR 46 = 6)
11
A1
A2
37
1–2
1–3
38
38
MX14 OPTION
39
39
40
40
NOTE 1:
41
WIRE TB3-7 TO TB3-8 IF OPTIONS D13, D33 OR MX12 ARE NOT ORDERED.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
23
41
P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
3
ANALOG SIGNAL FOLLOWER
4
4
160
CONTROL BOARD
TB3
5
1
+10V POT
5
6
2
WIPER/0-10VDC INPUT
6
7
3
COMMON
7
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
10
5
RUN REVERSE
6
RUN FORWARD
11
11
12
12
13
13
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
14
15
15
16
16
9
17
17
PROGRAMMABLE RELAY
OUTPUTS
10
18
18
INPUT MODE 6
19
(PAR 46 = 6)
11
19
20
20
22
22
PRESET SPEED MODEL
23
23
160
CONTROL BOARD
TB3
24
1
SW1
24
25
2
SW2
25
26
3
COMMON
26
4
SW3
27
27
28
28
TERMINAL BLOCK TB3
29
5
RUN REVERSE
6
RUN FORWARD
29
30
30
31
31
32
32
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
33
34
34
35
35
9
36
36
PROGRAMMABLE RELAY
OUTPUTS
10
37
37
INPUT MODE 6
38
(PAR 46 = 6)
11
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
24
MX19
A
B
C
D
E
F
G
H
1
1
2
ANALOG SIGNAL FOLLOWER
2
3
160
CONTROL BOARD
3
TB3
4
5
6
1
+10V POT
2
WIPER/0-10VDC INPUT
3
COMMON
4
4-20mA INPUT
5
RUN REVERSE
6
RUN FORWARD
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
4
5
6
OFF
REMOTE
7
20
B(A1)
B(A2)
21
XOO
8
8
TERMINAL BLOCK TB3
9
10
7
W(A1)
W(A2)
22
10
19-17
SS2
11
9
CR1
11
12
13
12
13
14
14
9
15
CUSTOMER
PLC OUTPUT
16
17
16
PROGRAMMABLE RELAY
OUTPUTS
10
19-11
CUSTOMER SUPPLIED AND
PROTECTED 120VAC
15
CR1
*
INPUT MODE 6
18
17
(PAR 46 = 6)
11
18
19
19
20
20
PRESET SPEED MODEL
22
160
CONTROL BOARD
TB3
23
24
25
22
1
SW1
2
SW2
3
COMMON
4
SW3
5
RUN REVERSE
6
RUN FORWARD
7
COMMON
8
TB3/KEYPAD OR COMMUNICATION CONTROL
23
24
25
OFF
LOCAL
26
20
REMOTE
B(A1)
B(A2)
21
26
XOO
27
27
TERMINAL BLOCK TB3
28
W(A1)
29
W(A2)
29
19-39
SS2
30
28
CR1
22
30
31
32
31
32
33
33
9
34
35
34
35
PROGRAMMABLE RELAY
OUTPUTS
10
INPUT MODE 6
36
36
(PAR 46 = 6)
11
37
37
38
38
CUSTOMER
PLC OUTPUT
39
CR1
39
19-30
CUSTOMER SUPPLIED AND
PROTECTED 120VAC
40
*
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
25
Notes
26
Twenty-Four Volt DC (24VDC) Control Interface
for Analog and Preset Drives
Power Distribution and DS Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Operator Interface Options DN2C, RS1C, P1C, RPAC, P2C, and
Ready/Fault Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Enclosure Mounted DeviceNet Connector Options: DNSC1, DNSC2, DNBC1,
DNBC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Drive Ratings and DS Option Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Product Control Logic Options
D13 Without P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
D13 With P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
D17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
D32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
D33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
D13 and D32 Without P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
D13 and D32 With P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
D17 and D32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
D32 and D33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
D35 and D36 Without Keypad or Comm Control Options. . . . . . . . . . . . . . . . . . . . . . . . . . 39
D35 and D36 With Keypad or Comm Control Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
D61 for Analog Signal Follower Drives Without Keypad or Comm Control Options . . . . . 41
D61 for Analog Signal Follower Drives With Keypads or Comm Control Options. . . . . . . 42
MX12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
MX14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 and 44
MX19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
27
Power Distribution and DS Option
A
B
C
D
E
F
G
H
1
1
BRAKE
1C
2
2
L2
*
1PH, 50/60HZ
AC LINES
3
3
L3
17-18
17-37
4
L1
5
1
DISCONNECTING
D
MEANS AND
SHORT CIRCUIT
L2
6
3PH, 50/60HZ
AC LINES
7
LINE FILTER
2
MX14 OPTION
5
5
6
MODULE
PROVIDED BY
OTHERS
WHEN DS OPTION
IS NOT ORDERED
L3
4
4
3
6
7
LINE
PE
8
8
POWER DISCONNECTING OPTION
9
9
DS OPTION
10
10
CHASSIS
EA1
GRD
11
R
S
T
(STD)
READY/FAULT PANEL
(OPTIONAL)
RS1C RS232 SERIAL COM
13
1
L2
F2
2
L3
F3
3
12
TERMINAL BLOCK TB2
(INTERFACE CONTROL BOARD)
FOR DETAILED INFORMATION,
REFER TO CONTROL OPTIONS
P2C REMOTE KEYPAD MODULE
DN2C DEVICE NET PANEL
RS1C RS232 SERIAL COM
PD1C PROFIBUS MODULE
IB1C INTERBUS MODULE
14
F1
11
EA2
12
L1
13
TABLE 1
600V
14
DS1
15
15
DN2 DEVICE NET PANEL
BLK
16
BLU
CUSTOMER
DEVICE-NET
CONNECTION
17
18
OPTIONS
20
LINE FILTER OPTION
EMC OPTION
3
WHT
17
4
RED
5
RF1
1
30
31
L1
L1'
4
18
5
19
6
20
lLINE FILTER
OPTIONAL
DNSC1
DNSC2
DNBC1
DNBC2
16
2
GRAY
5-PIN CONNECTOR
19
1
2
TO
3
17-38
L2
L3
MODULE
L2'
TABLE 1
L3'
MX14 OPTION
BULLETIN 160 SMART SPEED CONTROLLER
22
23
TABLE 1 . HP
ANALOG SIGNAL FOLLOWER/PRESET SPEED MODEL
TABLE 1 VOLTS
FOR FURTHER DRIVE INFORMATION, REFER TO
TABLE 1 AMPS
160 SSC™ VARIABLE SPEED DRIVE USER MANUAL
22
23
24
24
NOTE: MOTOR FLA MUST NOT
EXCEED DRIVE AMP RATING.
TERMINAL BLOCK TB2
25
BR+
26
BR-
+DC
-DC
GRD
U
V
25
W
26
27
27
OPERATOR INTERFACE
MODULE
28
29
PROGRAM
RUN
ESC
30
FORWARD
28
29
REVERSE
SEL
30
31
31
MOTOR DATA
32
32
HP
VOLTS
33
(T2)
OPTIONAL
P2C
(T1)
(T3)
(G)
34
33
FLA
AC
MOTOR *
RPM (BASE)
34
REFER TO MOTOR NAMEPLATE
FOR EXACT DATA.
35
GENERAL NOTES:
35
4. COIL AND CONTACT CROSS REFERENCING - NUMBERS ADJACENT TO
36
36
1.
- BUILDING GROUND TO BE GROUNDED
BY CUSTOMER.
37
TE
38
PE
37
- SIGNAL COMMON
1-3
CATES SHEET NO. 1.
DERSCORED TEXT LINE INDICATES
ORMALLY CLOSED CONTACT.
- CHASSIS CONNECTION.
39
2. * -INDICATES COMPONENTS SUPPLIED BY OTHERS.
-INDICATES TB4 TERMINAL BLOCK.
3.
4
39
OFF-PAGE CROSS REFERENCING - NUMBERS ADJACENT TO SOURCE
40
41
38
- POWER EQUIPMENT GROUND
40
FROM
M 1-24
41
-INDICATES TERMINAL ON INDIVIDUAL
COMPONENTS.
TO 1-24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
28
-INDICATES SHEET NO. 1.
Drive Ratings and DS Option Ratings
A
B
C
D
E
F
G
H
1
1
TABLE 1
2
2
3
3
SINGLE PHASE
4
4
DRIVE RATINGS
CATALOG NO. (HP)
VOLTAGE
5
FUSE RATINGS (DS OPTION)
TYPE
6
200-240V
200-240V
200-240V
200-240V
160S-AA02* (.5)
160S-AA03* (.75)
160S-AA04* (1)
160S-AA08* (2)
7
LINE FILTER MODULE
FLA
2.3A
3.0A
4.5A
8.0A
LPJ
LPJ
LPJ
LPJ
AMP
VOLT
6A
10A
15A
30A
600V
600V
600V
600V
CATALOG NUMBER
5
6
160S-RFA-9-A
160S-RFA-9-A
160S-RFA-9-A
160S-RFA-16-B
7
8
8
THREE PHASE
9
DRIVE RATINGS
VOLTAGE
10
CATALOG NO.
(HP)
11
12
13
14
15
16
9
FUSE RATINGS (DS OPTION)
TYPE
AMP
VOLT
10
LINE FILTER MODULE
FLA
CATALOG NUMBER
11
160-AA02* (.5)
160-AA03* (.75)
160-AA04* (1)
160-AA08* (2)
160-AA12* (3)
160-AA18* (5)
200-240V
200-240V
200-240V
200-240V
200-240V
200-240V
2.3A
3.0A
4.5A
8.0A
12.0A
18.0A
LPJ
LPJ
LPJ
LPJ
LPJ
LPJ
6A
6A
10A
15A
20A
30A
600V
600V
600V
600V
600V
600V
160-RFB-5-A
160-RFB-5-A
160-RFB-5-A
160-RFB-14-A
160-RFB-14-A
160-RFB-22-B
160-BA01* (.5)
160-BA02* (.75)
160-BA03* (1)
160-BA04* (2)
160-BA06* (3)
160-BA10* (5)
380-460V
380-460V
380-460V
380-460V
380-460V
380-460V
1.2A
1.7A
2.3A
4.0A
6.0A
10.5A
LPJ
LPJ
LPJ
LPJ
LPJ
LPJ
4A
4A
5A
8A
15A
20A
600V
600V
600V
600V
600V
600V
160-RFB-5-A
160-RFB-5-A
160-RFB-5-A
160-RFB-5-A
160-RFB-14-A
160-RFB-14-B
12
13
14
15
16
17
17
* - CATALOG NO. SUFFIX CAN CONTAIN "SF1" OR "PS1"
18
18
19
19
20
20
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
29
D13 Without P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
OFF
HAND
11
20 (1)
(XOO)
12
10
5
5
RUN REVERSE
6
6
RUN FORWARD
AUTO
(2)
SLOT-1
11
21
R
12
NOTE 1:
13
7
7
COMMON
13
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
14
(4)
(3)
(OOX)
15
14
22
R
SS2
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
+
23
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
22
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
OFF
HAND
30
20 (1)
(XOO)
31
29
AUTO
(2)
SLOT-1
30
21
R
31
NOTE 1:
32
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
33
(4)
(OOX)
34
(3)
33
22
R
SS2
34
35
9
9
35
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
30
D13 With P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
OFF
HAND
11
20 (4)
(OOX)
12
AUTO
5
RUN REVERSE
6
6
RUN FORWARD
11
(3)
R
SLOT-2
10
5
2-WIRE
DEVICE
12
*
NOTE 1:
13
13
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-1
14
(1)
(2)
(XOO)
15
14
22
R
SS2
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
+
23
22
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
OFF
HAND
30
20
(4)
(OOX)
31
AUTO
30
(3)
SLOT-2
29
2-WIRE
DEVICE
R
31
*
NOTE 1:
32
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-1
33
(1)
(XOO)
34
(2)
33
22
R
SS2
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
31
D17
A
B
C
D
E
F
G
H
1
1
2
2
24VDC
INTERFACE
3
+
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
4
3
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
5
5
REVERSE
6
6
START
10
START
11
20
(3)
(4)
12
11
21
R
PB2
12
SLOT-1
NOTE 1:
13
7
7
COMMON
8
8
STOP
13
STOP
14
(1)
(2)
PB3
15
14
22
R
15
SLOT-1
9
9
10
10
16
16
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
11
20
20
24VDC
INTERFACE
22
+
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
23
22
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
REVERSE
6
6
START
27
27
28
28
TERMINAL BLOCK TB3
29
29
START
30
20
(3)
(4)
PB2
31
30
21
R
31
SLOT-1
NOTE 1:
32
7
7
COMMON
8
8
STOP
32
STOP
33
(1)
(2)
34
33
22
R
PB3
34
SLOT-1
9
9
10
10
35
35
36
11
38
36
PROGRAMMABLE RELAY
OUTPUTS
37
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
32
D32
A
B
C
D
E
F
G
H
1
1
2
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
10
R
(OX)
START
11
20
9
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
5
5
REVERSE
6
6
START
10
SLOT-2
11
21
*
12
12
NOTE 1:
13
7
7
COMMON
8
8
STOP
13
STOP
14
14
22
*
15
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
11
20
20
22
+
23
22
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
REVERSE
6
6
START
27
27
28
FORWARD
(OX)
START
30
20
R
SS3
28
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
29
29
SLOT-2
30
21
*
31
31
NOTE 1:
32
33
STOP
34
*
7
7
COMMON
8
8
STOP
32
33
22
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
D33
A
B
C
D
E
F
G
H
1
1
2
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
10
5
5
RUN REVERSE
6
6
RUN FORWARD
2-WIRE
DEVICE
11
12
11
12
*
NOTE 1:
13
LOCAL
20 (3)
(OX)
14
15
REMOTE
(4) 22
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
R
SS1
13
7
15
SLOT-1
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
+
23
22
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
29
2-WIRE
DEVICE
30
31
30
31
*
NOTE 1:
32
LOCAL
20 (3)
(OX)
33
34
REMOTE
(4) 22
7
COMMON
32
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
R
SS1
7
34
SLOT-1
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
34
D13 and D32 Without P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
OFF
9
HAND
20
10
AUTO
(1)
(XOO)
(2)
SLOT-1
21
R
(OX)
R
11
(1)
(2)
(XO)
12
10
5
5
RUN REVERSE
6
6
RUN FORWARD
11
24
R
SS3
9
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
12
NOTE 1:
13
13
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
14
15
(4)
(3)
(OOX)
R
SS2
14
22
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
+
23
22
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
OFF
28
HAND
FORWARD
20 (1)
(XOO)
29
(2)
SLOT-1
21
R
(OX)
R
28
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
29
SLOT-2
O
30
(1)
(XO)
31
(2)
30
24
R
SS3
31
SLOT-1
NOTE 1:
32
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
33
(4)
(3)
(OOX)
34
SS2
33
22
R
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
35
D13 and D32 With P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
AUTO CONTROL
OFF
9
HAND
20
10
AUTO
(4)
(OOX)
(3)
SLOT-1
2-WIRE
DEVICE
21
9
TERMINAL BLOCK TB3
23
(4)
24
R
R
10
5
5
RUN REVERSE
6
6
RUN FORWARD
*
11
11
25
R
(XO)
12
12
NOTE 1:
13
7
7
COMMON
13
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
14
15
(1)
(2)
(XOO)
R
SS2
14
22
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
+
23
22
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
AUTO CONTROL
OFF
28
AUTO
20
29
(3)
(OOX)
SLOT-1
2-WIRE
DEVICE
21
FORWARD
23
R
R
28
TERMINAL BLOCK TB3
REVERSE
24
29
SLOT-2
*
30
(1)
(XO)
31
(2)
SS3
30
25
R
31
SLOT-1
NOTE 1:
32
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
33
(1)
(XOO)
34
(2)
SS2
33
22
R
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
36
D17 and D32
A
B
C
D
E
F
G
H
1
1
2
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
10
R
(OX)
START
11
20
(3)
9
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
5
5
REVERSE
6
6
START
10
SLOT-2
(4)
11
21
PB2
12
12
SLOT-1
NOTE 1:
13
7
7
COMMON
8
8
STOP
13
STOP
14
(1)
(2)
14
22
PB3
15
15
SLOT-1
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
11
20
20
22
+
23
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
22
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
REVERSE
6
6
START
27
27
28
FORWARD
(OX)
START
30
20
(3)
R
SS3
28
TERMINAL BLOCK TB3
REVERSE
(4) 23
(3)
29
29
SLOT-2
(4)
30
21
PB2
31
31
SLOT-1
NOTE 1:
32
7
7
COMMON
8
8
STOP
32
STOP
33
(1)
(2)
33
22
PB3
34
34
SLOT-1
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
37
D32 and D33
A
B
C
D
E
F
G
H
1
1
2
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
2-WIRE
DEVICE
9
TERMINAL BLOCK TB3
(4)
10
23
R
10
5
5
RUN REVERSE
6
6
RUN FORWARD
*
11
(2)
12
11
24
R
(XO)
12
NOTE 1:
13
LOCAL
20 (3)
(OX)
14
15
REMOTE
(4) 22
7
COMMON
13
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
R
SS1
7
15
SLOT-1
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
+
23
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
22
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
2-WIRE
DEVICE
FORWARD
29
R
(OX)
28
TERMINAL BLOCK TB3
REVERSE
(4) 23
29
*
30
(1)
(2)
(XO)
31
SS3
30
24
R
31
SLOT-1
NOTE 1:
32
LOCAL
20 (3)
(OX)
33
34
REMOTE
(4) 22
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
R
SS1
32
7
34
SLOT-1
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
38
D35 and D36 Without Keypad or Comm Control Options
A
B
C
D
E
F
G
H
TABLE 2
1
OPTION
SYMBOL
2
D35
D36
PL3
PL4
WHITE
RED
LEGEND
PAR 47 SETTING
1
DRIVE RUN
DRIVE FAULT
2
0 (DEFAULT)
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
5
5
REVERSE
6
6
START
10
START
11
20
11
21
*
12
12
NOTE 1:
13
7
7
COMMON
8
8
STOP
13
STOP
14
14
22
*
15
15
16
CUST.
SUPPLIED
120VAC
17
25
(X2)
18
16
9
9
10
10
17
PROGRAMMABLE RELAY
OUTPUTS
SEE TABLE 2
19
11
11
INPUT MODE 0
18
(PAR 46 = 0)
19
20
20
22
+
23
22
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
REVERSE
6
6
START
27
27
28
28
TERMINAL BLOCK TB3
29
29
START
30
20
30
21
*
31
31
NOTE 1:
32
33
STOP
34
*
COMMON
8
8
STOP
32
34
35
36
7
33
22
CUST.
SUPPLIED
120VAC
7
PILOT DEVICE
25
(X2)
35
9
9
10
10
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
39
D35 and D36 With Keypad or Comm Control Options
A
B
C
D
E
F
G
H
TABLE 2
1
OPTION
SYMBOL
2
D35
D36
PL3
PL4
WHITE
RED
LEGEND
PAR 47 SETTING
1
DRIVE RUN
DRIVE FAULT
2
0 (DEFAULT)
2
3
+
4
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
3
ANALOG SIGNAL FOLLOWER
4
160
CONTROL BOARD
TB3
TB3
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
5
8
8
9
9
TERMINAL BLOCK TB3
10
5
5
RUN REVERSE
6
6
RUN FORWARD
10
2-WIRE
DEVICE
11
12
11
12
*
NOTE 2:
13
REMOTE
14
(OX)
17
25
(X2)
18
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
13
15
16
CUST.
SUPPLIED
120VAC
7
14
R
*
15
7
LOCAL
9
9
10
10
16
17
PROGRAMMABLE RELAY
OUTPUTS
SEE TABLE 2
19
11
11
INPUT MODE 6
18
(PAR 46 = 6)
19
20
20
22
+
23
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
22
PRESET SPEED MODEL
23
160
CONTROL BOARD
TB3
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
29
2-WIRE
DEVICE
30
31
30
31
*
NOTE 2:
32
REMOTE
33
(OX)
*
34
36
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
32
33
R
34
35
CUST.
SUPPLIED
120VAC
7
LOCAL
PILOT DEVICE
25
(X2)
9
9
10
10
35
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
NOTE 1:
39
39
CONNECT THE -24VDC & +24VDC TO TERMINALS TB3-7 & TB3-8 RESPECTIVELY WHEN
D13, D33 OR MX12 ARE NOT ORDERED.
40
41
40
41
NOTE 2: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
40
D61 for Analog Signal Follower Drives Without Keypad or Comm Control Options
A
B
C
D
E
F
G
H
1
1
2
2
3
3
24VDC
INTERFACE
4
ANALOG SIGNAL FOLLOWER
TB3
BLACK
5
SPEED
REF.
RH1
10K
6
RED
WHITE
7
SHLD
4
160
CONTROL BOARD
TB3
1
1
+10V POT
5
2
2
WIPER/0-10VDC INPUT
6
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
+
9
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
9
TERMINAL BLOCK TB3
10
5
5
REVERSE
6
6
START
10
START
11
20
11
21
*
12
12
NOTE 1:
13
7
7
COMMON
8
8
STOP
13
STOP
14
14
22
*
15
15
16
9
9
10
10
16
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
11
20
20
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
41
D61 for Analog Signal Follower Drives With Keypads or Comm Control Options
A
B
C
D
E
F
G
H
1
1
2
2
3
3
24VDC
INTERFACE
4
ANALOG SIGNAL FOLLOWER
TB3
BLACK
5
SPEED
REF.
RH1
10K
6
RED
WHITE
7
SHLD
4
160
CONTROL BOARD
TB3
1
1
+10V POT
5
2
2
WIPER/0-10VDC INPUT
6
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
+
9
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
10
OFF
HAND
9
TERMINAL BLOCK TB3
AUTO
10
5
5
RUN REVERSE
6
6
RUN FORWARD
2-WIRE
DEVICE
11
12
11
12
*
NOTE 2:
13
7
7
COMMON
13
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
14
*
15
15
16
9
9
10
10
16
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
NOTE 1:
CONNECT THE -24VDC & +24VDC TO TERMINALS TB3-7 & TB3-8 RESPECTIVELY WHEN
D13, D33 OR MX12 ARE NOT ORDERED.
30
30
31
31
NOTE 2: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
42
MX12
A
B
C
D
E
F
G
H
1
1
2
2
3
+
4
3
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
OFF
11
20
RUN FWD
21
(B)A2
(B)A1
(OX)
SS2
12
20
REMOTE
22
(B)A2
(B)A1
(OX)
SS1
15
RUN REVERSE
6
6
RUN FORWARD
12
NOTE 1:
LOCAL
5
11
R
13
14
10
5
13
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
R
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
+
23
22
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
29
LOCAL CONTROL
30
20
RUN FWD
21
(B)A2
(B)A1
(OX)
SS2
31
30
R
31
NOTE 1:
32
LOCAL
33
20
REMOTE
22
(B)A2
(B)A1
(OX)
34
SS1
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
R
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
NOTE 1: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
43
MX14
A
B
C
D
E
F
G
H
1
1
2
+
3
2
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
ANALOG SIGNAL FOLLOWER
TB3
3
160
CONTROL BOARD
TB3
4
1
1
+10V POT
4
5
2
2
WIPER/0-10VDC INPUT
5
6
3
3
COMMON
6
4
4
4-20mA INPUT
7
7
8
8
TERMINAL BLOCK TB3
9
9
5
5
RUN REVERSE
6
6
RUN FORWARD
2-WIRE
DEVICE
10
11
10
11
*
12
NOTE 2:
LOCAL
13
(OX)
14
FROM
1-19
24VDC
18
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
13
14
31
17
7
*
15
16
12
7
REMOTE
15
9
9
10
10
1C
30
32
11
A1
A2
16
PROGRAMMABLE RELAY
OUTPUTS
11
INPUT MODE 6
17
(PAR 46 = 6)
18
–
1–3
19
19
MX14 OPTION
20
+
20
24VDC
INTERFACE
-
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
22
PRESET SPEED MODEL
TB3
22
160
CONTROL BOARD
TB3
23
1
1
SW1
23
24
2
2
SW2
24
25
3
3
COMMON
25
4
4
SW3
26
26
27
27
TERMINAL BLOCK TB3
28
5
5
RUN REVERSE
6
6
RUN FORWARD
28
2-WIRE
DEVICE
29
30
29
30
*
31
NOTE 2:
LOCAL
32
(OX)
33
36
37
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
32
*
33
9
9
10
10
34
35
31
FROM
1-19
24VDC
7
REMOTE
34
35
31
7
OUTPUTS
1C
30
32
11
A2
11
INPUT MODE 6
36
(PAR 46 = 6)
37
38
38
MX14 OPTION
39
39
NOTE 1:
40
40
CONNECT THE -24VDC & +24VDC TO TERMINALS TB3-7 & TB3-8 RESPECTIVELY WHEN
D13, D33 OR MX12 ARE NOT ORDERED.
41
41
NOTE 2: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
44
MX19
A
B
C
D
E
F
G
H
1
1
+
2
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
-
24VDC
INTERFACE
3
TB3
4
5
6
ANALOG SIGNAL FOLLOWER
2
160
CONTROL BOARD
3
TB3
1
1
+10V POT
2
2
WIPER/0-10VDC INPUT
3
3
COMMON
4
4
4-20mA INPUT
5
5
RUN REVERSE
6
6
RUN FORWARD
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
9
9
10
10
11
11
4
5
6
OFF
REMOTE
7
20
B(A1)
B(A2)
21
XOO
8
8
TERMINAL BLOCK TB3
9
10
7
W(A1)
W(A2)
22
10
18-17
SS2
11
9
CR1
11
NOTE 2:
12
13
12
13
14
14
15
CUSTOMER
PLC OUTPUT
16
18-10
CUSTOMER SUPPLIED AND
PROTECTED 120VAC
17
15
CR1
16
PROGRAMMABLE RELAY
OUTPUTS
*
INPUT MODE 6
18
17
(PAR 46 = 6)
18
19
19
20
20
+
CUSTOMER SUPPLIED
AND PROTECTED 24VDC
-
24VDC
INTERFACE
22
PRESET SPEED MODEL
23
24
25
160
CONTROL BOARD
TB3
TB3
22
1
1
SW1
2
2
SW2
3
3
COMMON
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
9
9
10
10
23
24
25
OFF
LOCAL
26
20
REMOTE
B(A1)
B(A2)
21
26
XOO
27
TERMINAL BLOCK TB3
28
29
W(A1)
W(A2)
28
CR1
22
29
18-36
SS2
30
27
30
NOTE 2:
31
32
31
32
33
33
34
CUSTOMER
PLC OUTPUT
35
18-29
CUSTOMER SUPPLIED AND
PROTECTED 120VAC
36
34
CR1
PROGRAMMABLE RELAY
OUTPUTS
35
INPUT MODE 6
*
11
37
36
(PAR 46 = 6)
11
37
38
38
39
39
NOTE 1:
CONNECT THE -24VDC & +24VDC TO TERMINALS TB3-7 & TB3-8 RESPECTIVELY WHEN
D13, D33, MX12 OR MX19 ARE NOT ORDERED.
40
41
40
41
NOTE 2: CONNECT TERMINAL 7 TO ENCLOSURE GROUND WHEN EMC OPTION IS PRESENT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
45
Notes
46
One Hundred Twenty Volt AC (120VAC) Control Interface
for Analog and Preset Drives
Power Distribution and DS Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Operator Interface Options DN2C, RS1C, P1C, RPAC, P2C, and
Ready/Fault Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Enclosure Mounted DeviceNet Connector Options: DNSC1, DNSC2,
DNBC1, DNBC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Drive Ratings and DS Option Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Product Control Logic Options
D13 Without P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
D13 With P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
D17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
D32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
D33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
D13 and D32 Without P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
D13 and D32 With P2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
D17 and D32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
D32 and D33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
D35 and D36 Without Keypad or Comm Control Options. . . . . . . . . . . . . . . . . . . . . . . . . . 59
D35 and D36 With Keypad or Comm Control Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
D61 for Analog Signal Follower Drives Without Keypad or Comm Control Options . . . . . 61
D61 for Analog Signal Follower Drives With Keypad or Comm Control Options . . . . . . . 62
MX12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
MX14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 and 64
MX19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
47
Power Distribution and DS Option
A
B
C
D
E
F
G
H
1
1
BRAKE
1C
2
2
L2
*
1PH, 50/60HZ
AC LINES
3
4
L1
5
6
3PH, 50/60HZ
AC LINES
4
MX14 OPTION
1
DISCONNECTING
D
MEANS AND
SHORT CIRCUIT
L2
7
3
L3
17-18
17-37
PROVIDED BY
OTHERS
WHEN DS OPTION
IS NOT ORDERED
L3
5
2
6
3
7
LINE
8
8
PE
POWER DISCONNECTING OPTION
9
9
DS OPTION
10
10
CHASSIS
EA1
GRD
11
R
S
T
(STD)
READY/FAULT PANEL
(OPTIONAL)
RS1C RS232 SERIAL COM
13
1
L2
F2
2
L3
F3
3
12
TERMINAL BLOCK TB2
(INTERFACE CONTROL BOARD)
FOR DETAILED INFORMATION,
REFER TO CONTROL OPTIONS
P2C REMOTE KEYPAD MODULE
DN2C DEVICE NET PANEL
RS1C RS232 SERIAL COM
PD1C PROFIBUS MODULE
IB1C INTERBUS MODULE
14
F1
11
EA2
12
L1
TABLE 1
600V
13
DS1
14
15
15
DN2 DEVICE NET PANEL
BLK
16
BLU
CUSTOMER
DEVICE-NET
CONNECTION
17
WHT
19
DNSC1
DNSC2
DNBC1
DNBC2
20
30
3
4
RED
5-PIN CONNECTOR
16
2
GRAY
18
OPTIONS
1
17
5
18
31
OPTIONAL
19
TO
17-11
20
MX14 OPTION
BULLETIN 160 SMART SPEED CONTROLLER
22
22
TABLE 1 . HP
TABLE 1 VOLTS
23
23
TABLE 1
™ VARIABLE SPEED DRIVE USER MANUAL
24
24
NOTE: MOTOR FLA MUST NOT
EXCEED DRIVE AMP RATING.
25
BR+
26
BR-
+DC
-DC
GRD
U
V
25
W
26
27
27
OPERATOR INTERFACE
MODULE
28
28
REVERSE
PROGRAM
29
29
30
30
31
31
MOTOR DATA
HP
32
32
VOLTS
(T2)
OPTIONAL
P2C
33
(T1)
(T3)
(G)
34
FLA
AC
MOTOR *
33
RPM (BASE)
34
REFER TO MOTOR NAMEPLATE
FOR EXACT DATA.
35
GENERAL NOTES:
4. COIL AND CONTACT CROSS REFERENCING - NUMBERS ADJACENT TO
COIL AND UNDER CONTACT INDICATE SHEET AND LINE NUMBERS.
36
36
- BUILDING GROUND TO BE GROUNDED
BY CUSTOMER.
37
TE
38
PE
37
- SIGNAL COMMON
1-3
CATES SHEET NO. 1.
38
- POWER EQUIPMENT GROUND
DERSCORED TEXT LINE INDICATES
NORMALLY CLOSED CONTACT.
- CHASSIS CONNECTION.
39
2. * -INDICATES COMPONENTS SUPPLIED BY OTHERS.
-INDICATES TB4 TERMINAL BLOCK.
41
4
39
OFF-PAGE CROSS REFERENCING - NUMBERS ADJACENT TO SOURCE
40
3.
35
40
FROM
M 1-24
41
-INDICATES TERMINAL ON INDIVIDUAL
COMPONENTS.
TO 1-24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
48
-INDICATES SHEET NO. 1.
Drive Ratings and DS Option Ratings
A
B
C
D
E
F
G
H
1
1
TABLE 1
2
2
SINGLE PHASE
3
4
5
160S-AA02* (.5)
160S-AA03* (.75)
160S-AA04* (1)
160S-AA08* (2)
6
3
FUSE RATINGS (DS OPTION)
DRIVE RATINGS
CATALOG NO.
VOLTAGE
FLA
200-240V
200-240V
200-240V
200-240V
4
2.3A
3.0A
4.5A
8.0A
TYPE
AMP
VOLT
LPJ
LPJ
LPJ
LPJ
6A
10A
15A
30A
600V
600V
600V
600V
5
6
7
7
THREE PHASE
8
9
CATALOG NO.
DRIVE RATINGS
VOLTAGE
12
13
14
15
9
FUSE RATINGS (DS OPTION)
FLA
10
11
8
TYPE
AMP
VOLT
160-AA02* (.5)
160-AA03* (.75)
160-AA04* (1)
160-AA08* (2)
160-AA12* (3)
160-AA18* (5)
200-240V
200-240V
200-240V
200-240V
200-240V
200-240V
2.3A
3.0A
4.5A
8.0A
12.0A
18.0A
LPJ
LPJ
LPJ
LPJ
LPJ
LPJ
6A
6A
10A
15A
20A
30A
600V
600V
600V
600V
600V
600V
160-BA01* (.5)
160-BA02* (.75)
160-BA03* (1)
160-BA04* (2)
160-BA06* (3)
160-BA10* (5)
380-460V
380-460V
380-460V
380-460V
380-460V
380-460V
1.2A
1.7A
2.3A
4.0A
6.0A
10.5A
LPJ
LPJ
LPJ
LPJ
LPJ
LPJ
4A
4A
5A
8A
15A
20A
600V
600V
600V
600V
600V
600V
10
11
12
13
14
15
16
16
* - CATALOG NO. SUFFIX CAN CONTAIN "SF1" OR "PS1"
17
17
18
18
19
19
20
20
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
49
D13 Without P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
10
5
5
RUN REVERSE
6
6
RUN FORWARD
OFF
HAND
11
AUTO
20
(1)
(XOO)
(2)
11
21
R
12
12
13
SLOT-2
O
14
(3)
(4)
(OOX)
15
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
22
R
SS2
13
7
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
29
OFF
HAND
AUTO
20
21
(1)
(2)
R
(XOO)
SLOT-1
O
30
31
30
31
32
SLOT-2
O
33
(3)
(4)
(OOX)
34
SS2
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
22
R
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
50
D13 With P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
OFF
HAND
11
20
(4)
(OOX)
(3)
SLOT-1
O
6
6
RUN FORWARD
12
R
SS2
13
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
22
(2)
(1)
15
RUN REVERSE
*
13
(XOO)
5
11
R
12
14
10
5
2-WIRE
DEVICE
AUTO
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
OFF
HAND
AUTO
20
(4)
(3)
R
(OOX)
SLOT-2
O
30
31
30
*
31
32
SLOT-1
O
33
(2)
(1)
(XOO)
34
SS2
29
2-WIRE
DEVICE
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
22
R
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
51
D17
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
5
5
REVERSE
6
6
START
10
START
11
20
(3)
(4)
12
11
21
R
PB2
12
13
7
7
COMMON
8
8
STOP
13
STOP
14
(2)
(1)
14
22
R
PB3
SLOT-1
15
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
11
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
REVERSE
6
6
START
27
27
28
28
TERMINAL BLOCK TB3
29
29
START
30
20
(3)
(4)
PB2
SLOT-1
31
30
21
R
31
32
7
7
COMMON
8
8
STOP
32
STOP
33
(2)
(1)
33
22
R
PB3
34
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
52
D32
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
23
(3)
10
(OX)
START
9
TERMINAL BLOCK TB3
FORWARD
5
5
REVERSE
6
6
START
10
SLOT-2
11
20
11
21
*
12
12
13
7
7
COMMON
8
8
STOP
13
STOP
14
14
22
*
15
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
11
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
REVERSE
6
6
START
27
27
28
FORWARD
30
20
R
(OX)
START
28
TERMINAL BLOCK TB3
REVERSE
23
(3)
29
29
30
21
*
31
31
32
7
7
COMMON
8
8
STOP
32
STOP
33
33
22
*
34
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
53
D33
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
10
5
5
RUN REVERSE
6
6
RUN FORWARD
2-WIRE
DEVICE
11
12
11
12
*
13
LOCAL
20 (3)
(OX)
14
REMOTE
(4) 22
13
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
SS1
SLOT-1
15
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
18
INPUT MODE 6
19
11
(PAR 46 = 6)
11
19
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
29
2-WIRE
DEVICE
30
31
30
31
*
32
LOCAL
20 (3)
(OX)
33
34
REMOTE
(4) 22
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
33
SS1
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
54
D13 and D32 Without P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
OFF
9
HAND
AUTO
20 (1)
(XOO)
10
(2)
FORWARD
REVERSE
21
(4)
23
(1)
(2)
24
(XO)
R
R
11
12
9
TERMINAL BLOCK TB3
10
5
5
RUN REVERSE
6
6
RUN FORWARD
11
12
SLOT-1
13
13
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
O
14
15
(4)
(3)
(OOX)
R
14
22
SS2
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
18
INPUT MODE 6
19
11
(PAR 46 = 6)
11
19
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
OFF
28
HAND
AUTO
20 (1)
(XOO)
29
(2)
FORWARD
REVERSE
21
R
(4)
23
(1)
(2)
24
(XO)
R
(OX)
29
SLOT-2
30
31
28
TERMINAL BLOCK TB3
30
SS3
SLOT-1
31
32
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
O
33
34
(4)
(3)
(OOX)
R
33
22
SS2
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
55
D13 and D32 With P2C
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
OFF
9
HAND
10
2-WIRE
DEVICE
AUTO
20
(3)
21
AUTO CONTROL
FORWARD
REVERSE
23 (3)
(OX)
R
(4)
24
(2)
25
9
TERMINAL BLOCK TB3
10
5
5
RUN REVERSE
6
6
RUN FORWARD
*
11
(1)
(XO)
12
11
R
SS3
SLOT-1
12
13
13
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
O
14
15
(1)
(2)
(XOO)
R
14
22
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
18
INPUT MODE 6
19
11
(PAR 46 = 6)
11
19
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
OFF
28
HAND
20 (4)
(OOX)
29
2-WIRE
DEVICE
AUTO
(3)
21
AUTO CONTROL
FORWARD
REVERSE
(3)
R
(OX)
SLOT-1
R
29
SLOT-2
30
31
28
TERMINAL BLOCK TB3
24
(4)
(1)
(2)
(XO)
R
30
25
SS3
SLOT-1
31
32
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
SLOT-2
O
33
(1)
(XOO)
34
(2)
33
22
R
SS2
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
56
D17 and D32
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
23
(3)
10
(OX)
START
9
TERMINAL BLOCK TB3
FORWARD
5
5
REVERSE
6
6
START
10
SLOT-2
11
20
(3)
(4)
11
21
PB2
SLOT-1
12
12
13
7
7
COMMON
8
8
STOP
13
STOP
14
(1)
(2)
14
22
PB3
SLOT-1
15
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
11
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
REVERSE
6
6
START
27
27
28
FORWARD
30
20
(3)
R
(OX)
START
(4)
28
TERMINAL BLOCK TB3
REVERSE
23
(3)
29
29
30
21
PB2
SLOT-1
31
31
32
7
7
COMMON
8
8
STOP
32
STOP
33
(1)
(2)
33
22
PB3
SLOT-1
34
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
57
D32 and D33
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
2-WIRE
DEVICE
FORWARD
REVERSE
(4)
10
9
TERMINAL BLOCK TB3
23
R
10
5
5
RUN REVERSE
6
6
RUN FORWARD
*
11
12
(1)
(2)
(XO)
R
11
24
12
13
LOCAL
14
20 (3)
(OX)
15
13
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
REMOTE
(4)
14
22
R
15
SLOT-1
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
18
INPUT MODE 6
19
11
(PAR 46 = 6)
11
19
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
2-WIRE
DEVICE
FORWARD
REVERSE
(4)
29
*
(OX)
R
(1)
(2)
(XO)
R
30
31
33
20 (3)
(OX)
34
29
30
24
SS3
SLOT-1
31
32
LOCAL
28
TERMINAL BLOCK TB3
23
32
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
REMOTE
(4)
SS1
SLOT-1
33
22
R
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
58
D35 and D36 Without Keypad or Comm Control Options
A
B
C
D
E
F
G
H
TABLE 2
1
OPTION
SYMBOL
2
D35
D36
PL3
PL4
WHITE
RED
LEGEND
PAR 47 SETTING
1
DRIVE RUN
DRIVE FAULT
2
0 (DEFAULT)
2
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 24VAC
4
3
ANALOG SIGNAL FOLLOWER
4
160
CONTROL BOARD
TB3
TB3
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
5
8
8
9
9
TERMINAL BLOCK TB3
10
5
5
REVERSE
6
6
START
10
START
11
20
11
21
12
12
*
13
7
7
COMMON
8
8
STOP
13
STOP
14
14
22
15
15
*
16
CUST.
SUPPLIED
120VAC
17
25
(X2)
18
9
9
10
10
16
17
PROGRAMMABLE RELAY
OUTPUTS
SEE TABLE 2
19
11
11
INPUT MODE 0
18
(PAR 46 = 0)
19
20
20
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 24VAC
23
22
PRESET SPEED MODEL
23
160
CONTROL BOARD
TB3
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
REVERSE
6
6
START
27
27
28
28
TERMINAL BLOCK TB3
29
29
START
30
20
30
21
31
31
*
32
7
7
COMMON
8
8
STOP
32
STOP
33
33
22
34
34
*
35
CUST.
SUPPLIED
120VAC
36
PILOT DEVICE
25
(X2)
9
9
10
10
35
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 0
37
(PAR 46 = 0)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
59
D35 and D36 With Keypad or Comm Control Options
A
B
C
D
E
F
G
H
TABLE 2
1
OPTION
SYMBOL
2
D35
D36
PL3
PL4
WHITE
RED
LEGEND
PAR 47 SETTING
1
DRIVE RUN
DRIVE FAULT
2
0 (DEFAULT)
2
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
4
3
ANALOG SIGNAL FOLLOWER
4
160
CONTROL BOARD
TB3
TB3
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
5
8
8
9
9
TERMINAL BLOCK TB3
10
5
5
RUN REVERSE
6
6
RUN FORWARD
10
2-WIRE
DEVICE
11
12
11
12
*
13
REMOTE
14
(OX)
15
17
*
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
13
15
25
(X2)
18
7
14
R
16
CUST.
SUPPLIED
120VAC
7
LOCAL
9
9
10
10
16
17
PROGRAMMABLE RELAY
OUTPUTS
SEE TABLE 2
19
11
11
INPUT MODE 6
18
(PAR 46 = 6)
19
20
20
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
23
22
PRESET SPEED MODEL
23
160
CONTROL BOARD
TB3
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
29
2-WIRE
DEVICE
30
31
30
31
*
32
REMOTE
33
(OX)
34
36
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
32
LOCAL
33
R
*
34
35
CUST.
SUPPLIED
120VAC
7
PILOT DEVICE
25
(X2)
9
9
10
10
35
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
39
INPUT MODE 6
37
(PAR 46 = 6)
38
39
NOTE 1:
CONNECT THE 120VAC HOT AND NEUTRAL TO TERMINALS TB3-8 & TB3-7 RESPECTIVELY WHEN
D13, D33 OR MX12 ARE NOT ORDERED.
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
60
D61 for Analog Signal Follower Drives Without Keypad or Comm Control Options
A
B
C
D
E
F
G
H
1
1
2
2
3
3
120VAC
INTERFACE
4
ANALOG SIGNAL FOLLOWER
TB3
BLACK
5
SPEED
REF.
RH1
10K
6
RED
WHITE
7
SHLD
4
160
CONTROL BOARD
TB3
1
1
+10V POT
5
2
2
WIPER/0-10VDC INPUT
6
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
9
9
TERMINAL BLOCK TB3
10
5
5
REVERSE
6
6
START
10
START
11
20
11
21
*
12
12
13
7
7
COMMON
8
8
STOP
13
STOP
14
14
22
15
15
*
16
9
9
10
10
16
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 0
18
19
(PAR 46 = 0)
19
11
11
20
20
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
61
D61 for Analog Signal Follower Drives With Keypad or Comm Control Options
A
B
C
D
E
F
G
H
1
1
2
2
3
3
120VAC
INTERFACE
4
ANALOG SIGNAL FOLLOWER
TB3
BLACK
5
SPEED
REF.
RH1
10K
6
RED
WHITE
7
SHLD
4
160
CONTROL BOARD
TB3
1
1
+10V POT
5
2
2
WIPER/0-10VDC INPUT
6
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
9
10
OFF
HAND
AUTO
9
TERMINAL BLOCK TB3
10
5
5
RUN REVERSE
6
6
RUN FORWARD
2-WIRE
DEVICE
11
12
11
12
*
13
7
7
COMMON
13
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
14
*
15
15
16
9
9
10
10
16
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
22
23
23
24
24
25
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
62
MX12
A
B
C
D
E
F
G
H
1
1
2
2
3
4
3
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
4
160
CONTROL BOARD
TB3
5
1
1
+10V POT
5
6
2
2
WIPER/0-10VDC INPUT
6
7
3
3
COMMON
7
4
4
4-20mA INPUT
8
8
9
9
TERMINAL BLOCK TB3
10
OFF
11
20
RUN FWD
21
(B)A2
(B)A1
(OX)
SS2
12
LOCAL
20
SS1
15
RUN REVERSE
6
6
RUN FORWARD
12
REMOTE
22
(B)A2
(B)A1
(OX)
5
11
R
13
14
10
5
13
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
14
R
15
16
16
9
9
10
10
17
17
PROGRAMMABLE RELAY
OUTPUTS
18
INPUT MODE 6
18
19
(PAR 46 = 6)
19
11
11
20
20
22
23
22
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
PRESET SPEED MODEL
TB3
23
160
CONTROL BOARD
TB3
24
1
1
SW1
24
25
2
2
SW2
25
26
3
3
COMMON
26
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
27
27
28
28
TERMINAL BLOCK TB3
29
29
LOCAL CONTROL
30
20
RUN FWD
21
(B)A2
(B)A1
(OX)
SS2
31
30
R
31
32
LOCAL
33
20
REMOTE
22
(B)A2
(B)A1
(OX)
34
SS1
7
7
8
8
32
COMMON
33
R
34
35
35
9
9
10
10
36
36
PROGRAMMABLE RELAY
OUTPUTS
37
38
11
11
INPUT MODE 6
37
(PAR 46 = 6)
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
63
MX14
A
B
C
D
E
F
G
H
1
1
2
3
2
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
ANALOG SIGNAL FOLLOWER
TB3
3
160
CONTROL BOARD
TB3
4
1
1
+10V POT
4
5
2
2
WIPER/0-10VDC INPUT
5
6
3
3
COMMON
6
4
4
4-20mA INPUT
7
7
8
8
TERMINAL BLOCK TB3
9
9
5
5
RUN REVERSE
6
6
RUN FORWARD
2-WIRE
DEVICE
10
11
10
11
*
12
LOCAL
13
(OX)
14
FROM
1-19
24VDC
18
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
13
14
31
17
7
*
15
16
12
7
REMOTE
15
9
9
10
10
1C
30
32
11
A1
A2
16
PROGRAMMABLE RELAY
OUTPUTS
11
INPUT MODE 6
17
(PAR 46 = 6)
18
–
1–3
19
19
MX14 OPTION
20
20
120VAC
INTERFACE
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
22
PRESET SPEED MODEL
TB3
22
160
CONTROL BOARD
TB3
23
1
1
SW1
23
24
2
2
SW2
24
25
3
3
COMMON
25
4
4
SW3
26
26
27
27
TERMINAL BLOCK TB3
28
5
5
RUN REVERSE
6
6
RUN FORWARD
28
2-WIRE
DEVICE
29
30
29
30
*
31
LOCAL
32
(OX)
33
36
37
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
32
*
33
9
9
10
10
34
35
31
FROM
1-19
24VDC
7
REMOTE
34
35
31
7
OUTPUTS
1C
30
32
11
A2
11
INPUT MODE 6
36
(PAR 46 = 6)
37
38
38
MX14 OPTION
39
39
NOTE 1:
40
40
CONNECT THE HOT AND NEUTRAL OF 120VAC TO TERMINALS TB3-8 & TB3-7 RESPECTIVELY WHEN
D13, D33 OR MX12 ARE NOT ORDERED.
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
64
41
MX19
A
B
C
D
E
F
G
H
1
1
120VAC
INTERFACE
2
3
TB3
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
4
5
6
ANALOG SIGNAL FOLLOWER
2
160
CONTROL BOARD
3
TB3
1
1
+10V POT
2
2
WIPER/0-10VDC INPUT
3
3
COMMON
4
4
4-20mA INPUT
5
5
RUN REVERSE
6
6
RUN FORWARD
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
9
9
10
10
11
11
4
5
6
OFF
REMOTE
7
20
B(A1)
B(A2)
21
XOO
8
8
TERMINAL BLOCK TB3
9
10
7
W(A1)
W(A2)
22
10
18-17
SS2
11
9
CR1
11
12
13
12
13
14
14
15
CUSTOMER
PLC OUTPUT
16
18-10
CUSTOMER SUPPLIED AND
PROTECTED 120VAC
17
15
CR1
16
PROGRAMMABLE RELAY
OUTPUTS
*
INPUT MODE 6
18
17
(PAR 46 = 6)
18
19
19
20
20
120VAC
INTERFACE
22
PRESET SPEED MODEL
CUSTOMER SUPPLIED
AND PROTECTED 120VAC
23
24
25
160
CONTROL BOARD
TB3
TB3
22
1
1
SW1
2
2
SW2
3
3
COMMON
4
4
SW3
5
5
RUN REVERSE
6
6
RUN FORWARD
7
7
COMMON
8
8
TB3/KEYPAD OR COMMUNICATION CONTROL
9
9
10
10
23
24
25
OFF
LOCAL
26
20
REMOTE
B(A1)
B(A2)
21
26
XOO
TERMINAL BLOCK TB3
27
28
W(A1)
29
W(A2)
28
CR1
22
29
18-36
SS2
30
27
30
31
32
31
32
33
33
34
CUSTOMER
PLC OUTPUT
35
18-29
CUSTOMER SUPPLIED AND
PROTECTED 120VAC
36
34
CR1
PROGRAMMABLE RELAY
OUTPUTS
35
INPUT MODE 6
*
11
37
36
(PAR 46 = 6)
11
37
38
38
39
39
NOTE 1:
40
40
CONNECT THE -24VDC & +24VDC TO TERMINALS TB3-7 & TB3-8 RESPECTIVELY WHEN
D13, D33, MX12 OR MX19 ARE NOT ORDERED.
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
65
41
Material List for Spare Parts
A
B
C
D
E
F
G
H
MATERIAL LIST – COMPONENTS
1
1
A-B
MANUFACTURER/PART NO.
PART NO.
DESCRIPTION
2
EA1
F1-3
DS
RF1
P1
P2
DN2
RS1
DMPS1
DMSF1
LTN120
LTN120
SS1
SS2
SS3
PB2
PB3
PL3
PL4
RH1
1C
IB1
PD1
DNR
3
4
5
6
7
8
9
10
DRIVE UNIT
FUSES
DISCONNECT
LINE FILTER
PROG. KEYPAD
OP INTRF MOD
DEVICENET MOD.
SER. COM. MOD.
N/A
N/A
N/A
N/A
N/A
N/A
N/A
24V ANAL. INTRFCE
115V INTERFACE (SF)
115V INTERFACE (PS)
LOCAL/REMOTE SS
H O A SEL SW
FOR/REV SS
START PB
STOP PB
PILOT LIGHT, WHITE
PILOT LIGHT, RED
FREQ POT
CONTACTOR
INTERBUS MODULE
PROFIBUS MODULE
DEVICENET I/O RELAY
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
119331
N/A
N/A
N/A
N/A
2
REFER TO C-300316-12 FOR DRIVE CATALOG NO.
BUSSMANN/LPJ-*SP (NOTE 1)
AB/194R-NJ030P3
REFER TO C-300356-2, PAGE 2, TABLE 1 FOR CATALOG NO.
AB/160-P1
AB/160-P2
AB/160-DN2
AB/160-RS1
AB/160-DM-PS1
AB/160-DM-SF1
LEAF TECHNOLOGY/LT160-SF1-120VAC
LEAF TECHNOLOGY/LT160-PS1-120VAC
AB/800EP-SM24LX10
AB/800EP-SM32C24LX22
AB/800EP-SM24LX10
AB/800EP-F34LX10
AB/800EP-F44LX01
AB/800EP-PL74RL5
AB/800EP-PL44RL5
OHMITE CMU1031
AB/100-M05NZ243
AB/160-IB1
AB/160-PD1
AB/100-DNY42R
3
4
5
6
7
8
9
10
11
11
12
SS1
SS2
LOCAL/REMOTE SS
OFF/RUN FWD SS
N/A
N/A
AB/800EP-SM24LX10
AB/800T-H2A
MX12 OPTION ONLY
SS2
CR1
LOCAL-OFF-REMOTE SS
RELAY
N/A
N/A
AB/800T-J2A
AB/700-HA32A1
MX19 OPTION ONLY
12
13
13
14
14
15
15
16
16
17
17
18
18
19
19
20
20
22
22
23
23
24
GENERAL NOTES:
24
25
1. SEE TABLE 1 FOR FUSE SIZES.
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
34
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
66
blank page
www.rockwellautomation.com
Corporate Headquarters
Rockwell Automation, 777 East Wisconsin Avenue, Suite 1400, Milwaukee, WI, 53202-5302 USA, Tel: (1) 414.212.5200, Fax: (1) 414.212.5201
Headquarters for Allen-Bradley Products, Rockwell Software Products and Global Manufacturing Solutions
Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414.382.2000, Fax: (1) 414.382.4444
Europe: Rockwell Automation SA/NV, Vorstlaan/Boulevard du Souverain 36-BP 3A/B, 1170 Brussels, Belgium, Tel: (32) 2 663 0600, Fax: (32) 2 663 0640
Asia Pacific: Rockwell Automation, 27/F Citicorp Centre, 18 Whitfield Road, Causeway Bay, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846
Headquarters for Dodge and Reliance Electric Products
Americas: Rockwell Automation, 6040 Ponders Court, Greenville, SC 29615-4617 USA, Tel: (1) 864.297.4800, Fax: (1) 864.281.2433
Europe: Rockwell Automation, Brühlstraße 22, D-74834 Elztal-Dallau, Germany, Tel: (49) 6261 9410, Fax: (49) 6261 1774
Asia Pacific: Rockwell Automation, 55 Newton Road, #11-01/02 Revenue House, Singapore 307987, Tel: (65) 351 6723, Fax: (65) 355 1733
U.S. Allen-Bradley Drives Technical Support
Tel: (1) 262.512.8176, Fax: (1) 262.512.2222, Email: [email protected], Online: www.ab.com/support/abdrives
Publication 160-CDP — April 2002
Supersedes March 2001
P/N 300317 (04)
Copyright ® 2002 Rockwell Automation. All rights reserved. Printed in USA.