Download Cessna bird dog

Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Cessna bird dog
Item Nr: CY8069C
Instruction Manual
Before commencing assembly,please read these instructions thoroughly.
ALMOST - READY - TO - FLY
SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
lAssemble this kit only in places out of children ,s reach!
lTake enough safety precautions prior to operating this model.
You are responsible for this model,s assembly and safe operation!
lAlways keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
lCould cause serious injury or even death
SPECIFICATION
Wing Span:3100 mm (122 in)
Wing Area:115 dm2(1790sq.in)
Total Length: 2160 mm (85 in)
Flying Weight: 11kg
Engine : 80-100cc gas engine
Radio : 5channels ,8servos
REQUIRED FOR OPERATION (Purchase separately)
A minimum 5channel radio for airplanes (with 8servos).
And dry batteries.
1
!
5
B
Glue
A
CAUTION: Only use a minimum 5channel radio for
airplanes! (No other radio may be used!)
Epoxy Glue
6
A minimum 8 channel
transmitter for airplanes.
required for engine starting
!
Receiver
12 AA-size Batteries
Instant glue
Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
remote control
For handing the radio properly.refer to its instruction manual.
2
Battery (need 2)
Switch (need 2)
Fuel Pump
7
3
Servo(need 8 servos )
4
Engine and Muffler
Model A irplane engine:80-100cc gas engine
8
Plug Wrench
Silicone Tube
Fuel Filter
Other equipment for enhancing
airplane operation & perormance
Engine Starter
Muffler
9
Ignition
12V Battery (for starter)
Purchase a propeller that
will match your engine
26X10----28X10
26X12----28X12
TOOLS REQUIRED ( Purchase separately)
Sharp Hobby Knife
Phillips Screw Driver
Awl
Needle Nose Pliers
Wire Cutters
Scissors
BEFORE YOU BEGIN
. Read through the manual before you begin ,so you will have an overall idea of what to do.
2 . Check all parts .if you find any defective or missing parts .contact your local dealer.
1
Symbols used throughout this instruction manual,comprise.
3
A B
Drill holes with the specified
Diameter(here:2mm)
Must be purchased
separately!
Apply instant glue
(CA glue,super glue).
Ensure smooth non-binding
movement while assembling.
Pay close attention
here!
Assemble left and right
Sides the same way.
Cut off shaded portion.
Cut off excess.
2mm
!
Warning!
50
2
Apply epoxy glue.
C.A
L
R
2
Do not overlook this symbol.
3
Accessory list for this page.
!
Hinge
- - - - - -12
Hinge
------8
-----4
- - - - - 16
screw
1
4X30 Screw
-----4
Rod adjuster
-----8
Aileron and flap
- - - - - 12
Connecting rod head
-----4
screw
-----8
2.5X85mm rod
-----4
2X8mm
R
-----4
2.3X10mm Tp screw
3X30mm
L
HORN
Install the flap and aileron servo
Glue the hinges to the aileron
With AB instant glue
Aileron
L
Secure the servo , install the nylon horn
and connect the linkage
4
L
R
R
Flap
3mm
Servo line
A B
A B
Make sure hinges are
mounted in the same line
Aileron
2
Flap
Hinge
- - - - - -12
Hinge
------8
2.3X10mm Tp screw
3X30mm
L
screw
-----6
Glue the aileron and flap to the main
wing with AB glue
Bottom view
2X8mm
-----8
5
L
R
A B
HORN
-----2
screw
-----4
2.5X85mm rod
-----2
-----2
4X30 Screw
-----2
Rod adjuster
-----4
Connecting rod head
-----2
Secure the servo , install the nylon horn
and connect the linkage
R
3mm
Tailing edge
4mm
Servo line
Aileron
2.3X10mm Tp screw
Warning!
-----8
Aileron
Flap
Securely glue together. If coming off during flights,you'll
lose control of your airplane which leads to accidents!
3X30mm
screw
-----6
3
2X8mm
screw
-----4
2.5X85mm rod
-----2
HORN
-----2
-----2
4X30 Screw
-----2
Rod adjuster
-----4
Connecting rod head
-----2
8
Accessory list for this page.
!
Glue the elevator to the stabilizer by AB and epoxy
8mm nylon nut
A
B
----4
3X16mm
Screw
----4
3mm washer
----4
Hinge
Hinge
- - - - -8
6
-----8
9
Install the wings to the fuselage
Assembly the stabilizer carefully to the fuselage
A
B
12X715mm tube
25X1175mm tube
8mm nylon nut
----4
7
10
Main wing
3X16mm
Assembly of the stabilizer
Screw
----4
3mm washer
----4
,
C= C
,
B= B
,
A= A
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
4
!
13
Accessory list for this page.
Install the servo,install the nylon
horn and connect linkage
Horn
Rod
----4
1500mm steel wire
----2
3mm Lock Nut
----3
3X25mm Screw
----3
Rod adjuster
----8
2X8mm Screw
----8
4X30mm
Screw
------2
3X20mm
Screw
----6
Horn
----4
M5X50mm
----2
----2
Screw
----2
----2
M5X25mm
Connecting rod head
Screw
Connecting rod head
----4
----4
M5X65mm
2.5X125mm Rod
----2
Hinge
- - - - -3
----2
Screw
2.5X125mm Rod
----1
----2
M5 Lock Nut
3X20mm
------4
5mm washer
3X12mm
Screw
----2
Aluminium tube
------4
----6
Rod adjuster
----4
----4
3X12mm Screw
----2
2X8mm Screw
----4
4X30mm
11
Screw
14
Install the rudder to the fuselage
Screw
------2
Install the servo,install the nylon
horn and connect linkage
Rod
A
----4
1500mm steel wire
----2
Horn
----2
B
Connecting rod head
----2
3mm Lock Nut
----3
3X25mm
Screw
----3
Rod adjuster
----4
2X8mm Screw
----4
4X30mm
Hinge
Aluminium tube
------4
- - - - -3
12
15
Install the support to the stabilizer
Instal the main landing gear
M5X25mm
3X12mm Screw
----2
3X12mm
Screw
------2
Screw
----4
Screw
M5X65mm
----2
Screw
----1
5
M5X50mm
Screw
----2
M5 Lock Nut
------4
5mm washer
----4
Accessory list for this page.
!
6mm nut
6X9 screw
M3X20 Tp screw
----3
3.2mm Rocker
----1
3X3mm Screw
----3
3.2mm Collar
----2
----1
Install the engine
19
Assembly of the fuel tank
-----1
1500mm steel wire
----2
Aluminium tube
-----4
3.2mm Nylon Collar
----1
Linkage Stopper
1.8X550mm Rod
----1
2mm
18
------1
Nut
3X3mm Screw
----1
------1
16 Assembly of the
tail wheel
After confirming the
position(see front of
fuel tank).
Insert and tighten
the screw.
17
Assembly the fuel tank and battery to
20 appropriate
position
Install tail wheel to fuselage
Throttle servo
Fuel tank
Receiver
Battery
6mm nut
M3X20 Tp screw
----1
----3
3.2mm Rocker
6X9 screw
-----1
----1
3X3mm Screw
----3
3.2mm Nylon Collar
----1
Linkage Stopper
3.2mm Collar
----1
----2
2mm
1500mm steel wire
----2
Aluminium tube
-----4
Nut
------1
3X3mm Screw
----1
6
1.8X550mm Rod
------1
!
23
Accessory list for this page.
Install the window
50
2
Spring bolt
------1
C.A
Hinge
------6
2.3X10mm Tp Screw
----4
21
24
Glue the hings to the door
Glue the hings to the door
A
A
Spring bolt
------1
22
B
B
Hinge
------4
Hinge
------2
Glue the door to the fuselage
with AB glue
25
Glue the door to the fuselage
with AB glue
A
2.3X10mm Tp Screw
B
Here , install the servo
----4
7
!
28
Accessory list for this page.
3X12mm
Install the cowl
Screw
----4
3mm rubber band
----4
3mm washer
----4
2.3X10mm Tp Screw
- - - - 12
26
Cut away the surplus pats of canopy
Carefully along the shaded line
29
Install the light
2.3X10mm Tp Screw
----4
Install the front canopy
light
After install the light
Install the PVC cover
The light line
Blcak line
Battery
1.5V
1.5V
Cut away the surplus pats of canopy
Carefully along the shaded line
2.3X10mm Tp Screw
----4
Red line
27
3X12mm
30
Radio Equipment
Screw
3mm rubber band
----4
----4
Install the cover
2.3X10mm Tp Screw
3mm washer
----4
----4
8
31
33
Adjustment.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Side view
AILERON
Adjustment
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
5
Rudder
65
5
65
Flap
Side view
65
Top view
Top view
32
34
Adjustment.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
ELEVATOR
Adjustment.
115
Side view
140-150mm
115
CG
Top view
!
5
9
Warning!
NEVER fly the model
without well balancing.