Download Instruction Manual
Transcript
Thank you for choosing CYmodel Global : www.cymodel.com Australia : www.austars-model.com Italia : www.biellaexpress.com Pt-19 Item Nr: CY8023 Instruction Manual Before commencing assembly,please read these instructions thoroughly. ALMOST - READY - TO - FLY SAFETY PRECAUTIONS This radio control model is not a toy! lFirst-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent. lAssemble this kit only in places out of childrens, reach! lTake enough safety precautions prior to operating this model. You are responsible for this model ,s assembly and safe operation! lAlways keep this instruction manual ready at hand for quick reference,even after completing the assembly. lCould cause serious injury or even death SPECIFICATION Wing Span:2000 mm (79 in) Wing Area:61.3 dm2(950 sq.in) Total Length: 1550 mm (61 in) Take-off weight: 11 lb(5kg) Engine :2c 1.40-1.60cu.in 26cc gas engine Radio : 5 channels ,8 servos REQUIRED FOR OPERATION (Purchase separately) A minimum 5channel radio for airplanes (with 8servos). And dry batteries. 1 ! 5 B Glue A CAUTION: Only use a minimum 5channel radio for airplanes! (No other radio may be used!) Epoxy Glue 6 A minimum 5 channel transmitter for airplanes. required for engine starting ! Receiver 12 AA-size Batteries Instant glue Glow engine fuel only. WARNING: Normal gasoline cannot be used with glow engines. remote control For handing the radio properly.refer to its instruction manual. 2 3 4 Battery (need 2) Switch (need 2) Fuel Pump 7 Servo(need 8 servos ) 8 Engine and Muffler Model A irplane engine:2c 1.40-1.60cu.in 26cc gas engine Muffler Silicone Tube Fuel Filter Other equipment for enhancing airplane operation & perormance Glow plug Engine Starter 9 Muffler Plug Wrench 12V Battery (for starter) Purchase a propeller that will match your engine 16X10----18X10 Ignition TOOLS REQUIRED ( Purchase separately) Sharp Hobby Knife Phillips Screw Driver Awl Needle Nose Pliers Wire Cutters Scissors BEFORE YOU BEGIN . Read through the manual before you begin ,so you will have an overall idea of what to do. 2 . Check all parts .if you find any defective or missing parts .contact your local dealer. 1 Symbols used throughout this instruction manual,comprise. 3 A B Drill holes with the specified Diameter(here:2mm) Must be purchased separately! Apply instant glue (CA glue,super glue). Ensure smooth non-binding movement while assembling. Pay close attention here! Assemble left and right Sides the same way. Cut off shaded portion. Cut off excess. 2mm ! Warning! 50 2 Apply epoxy glue. C.A L R 2 Do not overlook this symbol. Horn ------4 2.3X10mm Tp screw - - - - - - 16 ------2 Connecting rod head 2X12mm Tp screw ------6 ------4 2x30mm Screw ------6 1.8X90mm rod L ------4 2x8mm Screw ------4 -----8 R R Aileron ------4 4 Install the aileron R Install the servo. Flap. Hinge Hinge 1 L Rod adjuster -----4 L 3 Accessory list for this page. ! Install the servo. A B Horn A B Make sure hinges are mounted in the same line Aileron Flap ------4 2.3X10mm Tp screw - - - - - - 16 ------2 Connecting rod head 2X12mm Tp screw ------6 Hinge --------8 2x30mm Hinge --------4 1.8X90mm Screw ------4 Rod adjuster ------6 2 L rod -----4 5 Install the servo. 2x8mm ------4 Screw ------4 Main wing Cut the film, put the aileron and flap servo line out R A B L R 3 L 2mm R 8 Accessory list for this page. ! 2.6mm Collar -----4 3X20mm Tp screw -----8 2.6mm Nylon collar -----2 -----2 2.6mm Nylon collar ----1 ----1 3X3mm screw ----1 3X12 Tp screw ----1 A B 3X12 Tp screw ----3 3X5 Screw ----3 3X5 ----1 Screw ----1 ----1 3X3mm screw ----1 -----2 5X45mm ----2 ----2 3X3mm screw 5.2mm Nylon collar ----1 screw ------2 5mm Washer ------2 2.6X12mm Tp screw ----1 ----1 Hinge 2.6X12mm Tp screw ----3 ----1 35mm wheel Hinge 35mm wheel ----1 6 2.6mm Collar Pressure plate 5.2mm Collar Install the rudder&tail wheel ----1 ----3 Install the main landing gear 9 Install the rudder&tail wheel 10 Install the rudder&tail wheel Pressure plate -----4 3X20mm Tp screw -----8 5.2mm Collar -----2 5.2mm Nylon collar -----2 3X3mm screw -----2 screw ------2 5mm Washer ------2 2 5X45mm Main wing installing 50 7 2.5mm C.A 4 ! 13 Main wing&Horizontal/Vertical tail Accessory list for this page. B 2X20mm screw ----3 2mm nut ----3 2X8mm screw ----4 1000mm Steel wire ----2 HORN C C A A B B C C ----2 Rod adjuster ----4 Connecting rod head ----4 Rod ----4 A Hinge --------6 11 B A Securely glue together ,if coming off during flights. You lose control of your airplane which leads to accidents! 14 Install the elevator Install the rudder servo A B 2X20mm Make sure hinges are mounted in the same line 2mm nut ----3 Hinge --------6 12 screw ----3 L 2X8mm R screw ----2 HORN ----2 Rod adjuster ----2 Connecting rod head ----2 1000mm Steel wire Rod ----2 15 Install the elevator Install the rudder servo Rod adjuster ----2 Connecting rod head 12X280mm tube ----2 Rod ----2 2X8mm A B screw ----2 2mm 5 ----2 18 Accessory list for this page. ! Horn ------2 Linkage Stopper ------1 ------2 Connecting rod head 2mm ------2 Screw 2x8mm ------2 2x20mm Screw Nut ------1 ------2 Rod adjuster 1.8X180mm Rod ------1 3X3mm Screw ------1 1.8X90mm ------6 16 Install the throttle servo Linkage Stopper 1.8X180mm Rod ------1 ----1 rod 2mm -----2 Nut 3X3mm Screw ----1 ------1 19 Assembly of the full tank Install the elevator servo After confirming the position(see front of fuel tank). Insert and tighten the screw. 2mm Horn ------2 ------2 Connecting rod head ------2 Rod adjuster 2x8mm ------2 Screw ------2 2x20mm Air pressure line Screw Fuel pipe ------6 1.8X90mm rod Fuel supply line -----2 17 20 Install the engine Radio Equipment Model A irplane engine:2c 1.40-1.60cu.in 26cc gas engine Throttle Fuel tank 140mm 140mm 6 Battery/Ignition Receiver ! 23 Accessory list for this page. 3X20mm Install the canopy screw 50 2 -----2 C.A 3mm Washer -----2 2.3X10mm Tp screw - - - - - - 14 L 21 Install the thr cowling R 24 Install the canopy 25 Install the canopy Propeller 2.3X10mm Tp screw ------6 2 Install the canopy 50 22 C.A 3X20mm screw -----2 7 3mm Washer -----2 2.3X10mm Tp screw ------8 26 28 Adjustment. Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. AILERON Adjustment Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. 40 Rudder 40 40 Side view 40 Flap Side view 45 Top view Top view 27 29 Adjustment. Never fly before checking the Cg s required position. In order to obtain the CG specified ,reposition the receiver and battery. Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. ELEVATOR Adjustment. 40 Side view 115-120mm 40 CG Top view ! 8 Warning! NEVER fly the model without well balancing.