Download SANAV GPS Tracker Utility Setup Guide
Transcript
SANAV GPS Tracker Utility Setup Guide Revision: 1.0.1 Revision Date: 2014/09/4 1. Notification ..................................................................................................................3 ......................................................................................3 ............................................................................................3 ..............................................................................................3 ..............................................................4 2. Installation ......................................................................................................................5 ! " # ....................................................5 .........................................................6 3. Setting Function.............................................................................................................8 3.1 User Settings:..............................................................................................8 3.1.1 Security Settings: ...........................................................................8 3.4 Report Settings .........................................................................................12 3.4.1 Auto Report.....................................................................................12 3.4.2 Over Speed Settings ....................................................................12 3.4.3 Panic.................................................................................................12 3.4.4 Move ............................................................. ! 3.4.5 Geofence .........................................................................................13 3.4.6 Report Tail.......................................................................................13 3.5 Geofence Settings....................................................................................15 3.6 Vibration Settings................................................. ! 3.7 Power Settings ...................................................... ! 4. Button Function ...........................................................................................................18 5. FAQ ...............................................................................................................................19 2 1. Notification ! " # & ' *+ & ' ( % % ( , - . .!/ -0-$1" ! & ' % ! & & % & % ( # ( % ( # # & & & ( '# ' 3 # & # # && ' # ' ' ( % & & & ' % & # ' && % 5 ) & & & # # & # " ( #' # && ' # , # & & ' ' ( & # 5 ' ( 2 '3 ' % % ( & " (& ) % $ , &( #( ' & ' # " # , 4& 4& # " # % & # 3 $ ! *676* " # % -& 5 4 2. Installation 1. Install the USB Driver and the GPS tracker Utility in the CD. 2. Turn on MU-201S1 before connecting it to a PC. 3. Plug in the AP Cable (connect USB to PC and Mini USB to MU201S1). 4. Check the COM Port from “Hardware Manager” in Windows OS 5 ! " # 4. The main screen of GPS Tracker Utility (MU Series). 5. Execute GPS Tracker Utility. Click on “Port” and select the Comm Port then Connect 6. Features on utility Setting Function Download Flash Backup data Erase Flash Backup data Firmware Version 6 7 3. Setting Function 3.1 User Settings: 8 Pin Code: * # 8* @ - 4 & ' ( : 0 ' % " ' ; <5( <=( <7( + 6> ? % ' 8A ' ' ' # 8 9 & ' & ' ( # # > B> # 48 7 4 7 # # ; B; # & ' :? & 3.1.1 Security Settings: Security Phone Switch: Enable or Disable Security Phone function. Security Phone Book: You can input 10 sets of Security Phone Numbers here. 8 3.2 GPRS Settings Route : Representation Router code 0 HTTP/SMS, send data to URL, if the URL is untouchable, then send it via SMS instead. 2 HTTP only, send data to URL, if the URL is untouchable, it won’t send the data by SMS. 4 SMS only, send data by SMS only. 6 TCP/SMS, send data to an assigned IP address, if the IP is untouchable, then send it via SMS instead. 7 TCP Only, only send data to an assigned IP address. 8 UDP/SMS; send data to an assigned IP address, if the IP is untouchable, then send it via SMS instead. 9 UDP Only; only send data to an assigned IP address 82 $C 8 C08G / !6 28 / "6 % 8 6 #& # 6 & &D & E F9997 & !( !6 ( 2 26 & Domain Name? : " & &8 66 "6 !- : ' $C? 9 3.3 Mode Setting & $ H ! & ! 6 2( 8 I!CJI0GJ 8 ( !6 2 & !C0G K & ' % % & 8 8 ( L % !6 2 H % $ ( # ' & ' ## 8 C " # # <77 % ( & # ' & % : < ?8 & # 8/ # & # % -00 # ' A8/ # & 10 -00 # C0 8& # ": @ ? % # 8 $ <9MMAM8 $ $ % # & & % # # ' & # <9MMAM8$ & # # % 11 3.4 Report Settings 3.4.1 Auto Report & $ C& C& " % N ' % ' O 4 & % ' # & <7777( # & C& C& 7777 3.4.2 Panic & $ ; > & C& ;- > " & <9M % & & # # 12 <7777( 7777 & C& 3.4.3 Geofence & $ ; $ C& & > :? ; $ > % <9M " % ## " & # & # <7777( 7777 & C& 3.4.5 Low Battery & $ 0 H % # ' AA <* @ ( 0 H & % 0 # ' M <AM @ ( 3.4.6 Report Tail Info Settings & $ @ ' #; C& " > ( ' & C& #@ " % #( @ #( $ ' ( /2"& (! ( " & A( # # 8- # ($ ( "& 8( - . 3.4.7 GSM Cell Info Settings & $ $ ! $ ! <P " ( !!8 !80 !8 <P !"8@ " !8 8C4 # 13 14 3.5 Over Speed Settings & $ -% 8& -% & 2 - 6-GG 8 - 2 & # - & 0 -% & .% <777 6 / / -% <7777 -% & C& & " % -% & <7777 % <7777( 7777 & C& 15 3.6 Non-Movement Settings Suspend the AUTO report and Geo-Fence when it detects non-movement. Report the MOVE message to the backend server when it detects movement. Report the STOP message to the backend server when it detects Non-movement. Change the report interval of Auto report to <rest report interval> when it detects non-movement. In the case, it just modify the AUTO report inteval but not suspend the AUTO report even if Bit0 is 1. & Movemen t duration $ 2 % <7777 Non-move ment 2 % <7777 duration Movemen t threshold 2 # C& ' # Rest report <77777 interval 16 3.7 Geofence Settings & $ 0 0 0 # 0 # C # C <7777 88.4 $ $ ## # 8" A8.4 " 17 4. Button Function % # ' ' *#+ , . % ' # & & . ( ) & % 0 # & % # .4 18 5. FAQ ! " " ' ' ' # $ % & ' ! " # & 19