Download USER`S MANUAL
Transcript
USER’’S MANUAL USER Pro CCTV Tester esterPro P28V1 Ver:STP Ver:ST 8V1.. 1 5 2009.5 2009. CCTV testerPRO User User’’s Manua Manuall Thank you for purchasi ng the CCTV security test er. Please rea d the manual before using the CCTV test erPRO, and use properly. For using the CCTV test erPRO safel y, please first rea d the「Safet y Inform ation」carefull y in the manual. The manual shoul d be kept wel l in case of reference. Keep the S/N label for aft er-sal e service withi n warranty period. Product without S/N label will be charged for repair servi ce. If there is any ques tion or probl em whil e using the CCTV test erPRO, or dam ages occurred on the product, please cont act our techni cal Departm ent. Ver: STP28V1.1 Page.1. CCTV testerPRO User User’’s Manua Manuall Table of Content 1 Sa fe ty In fo r m a ti o n ----------------------- ------------ -------------- -- --- ---------------------3 2 In tr o d u c ti o n -------------------------------------- --- ----------- --------- ------------------------ 4 2.1 Featu re s -------------- -------------- ---- ------- ---- ---------- ------ -------- ----------------------- 4 2.2 CCTV testerP RO Kits --------------------------- ---------------------------------- ------------- 5 2.3 Front Panel----------------------------------------- ------------------------------ ----------------6 2.4 Side View------------------------------------------ ------------------------------ ---------- ------- 8 2. 5 Installing the Batter y--------------------------- ----------------- --------------- ---------- ------- 9 3 Opera tion -------------------------------- ------------------------------------------------------- -------1 1 3.1 Power on/off ------------------- ------------------- ----------------- ------------------------------1 1 3.2 Menu & Functions---------------------- -------------------------------------- ------------------1 1 3.3 PTZ controller --------------------------- ------------------ --------- -------- ---------------------1 3 3.4 Video set ting ------------------------------ ------------- ------------------------------ ----------- 16 3. 5 Colorba r g enerato r ---------------- ------------------------- -- -- -------- ----------- ------------ 16 3. 6 Cable test er------------------------ ----------------------------- --------------- ------------------16 3. 7 Data monitor ------- ---------------------------------------------------------- ------------------- 17 3. 8 Device set ting------------------------------- --------------------------------------------- ------- 18 3.9 Address sea rch ------------------------------ --------------------------------------------- ------- 18 4 Specifica tion s ------ ----- ----------------- ------------------------------------ ---------------------------- 20 Page.2. Ver: STP28V1.1 CCTV testerPRO User User’’s Manua Manuall 1. Sa fe t y In fo r m a ti o n Notice The test er is intended to use in com pli ance with the local rul es of the el ectri cal usage and avoi d to appl y at the places whi ch are inappli cabl e for the use of el ectri cs such as hospit al, gas stati on et c. To prevent the functi onal decl ine or failure, the product shoul d not be spri nkl ed or dam ped. The expos ed part of the test er shoul d not be touched by the dust and liquid. During transportat ion and use, it is highl y recomm ended to avoi d the viol ent colli sion and vibrati on of the test er, lest dam agi ng com ponent s and causi ng failure. Don’ t leave the test er alone whil e charging and rec hargi ng. If the batt ery is found severely hot, the test er shoul d be powered off from the el ectri c source at once. The test shoul d not be charged over 8 hours. Don’ t use the test er where the humidit y is high. Once the test er is dam p, power off immediat el y and move away other cabl es connect ed. The test er shoul d not be use in the environm ent with the flam mabl e gas. Do not disassembl y the instrum ent since no com ponent inside can be repaired by the user. If the disassembl y is necess a ry indeed, please contact with the techni ci an of our com pany. The instrum ent shoul d not be used under the environm ent with strong el ectromagneti c interference. Don’ t touch the test er with wet hands or wat eris h things. Don’ t use the det ergent to cl ean and the dry clot h is suggest ed to use. If the dirt is not easy to remove, the soft clot h with wat er or neutral det ergent can be used. , but the clot h shoul d be twea ked suffi ciently. Ver: STP28V1.1 Page.3. CCTV testerPRO User User’’s Manua Manuall 2. In tr o d u ct io n The CCTV test erPRO is devel oped for the On-Sit e inst all ation and maint enance of video monitoring syst em. It can be used for displ ayi ng video, controlling PTZ, generating images, captu ring dat a of RS485 and testi ng LAN cable et c. Its functions, easy operation, and port ability makes it simple for the CCTV techni ci an to inst all and maint ai n CCTV system, improving work effi ci ency and get the labor cost down. 2. 1 Fe a tu r e s 2.8"TFT-LCD , 960(H)×240(V)resolution . PTZ control. Pan/tilts the P/T unit, zooms in/out the lens, adjus ts the focus, apert ure and sets and call s the prese t positi on Video displ ayi ng. Autom ati cally adapts and displays the video form at of NTSC/PAL. LCD Brightness/ Contras t/Color Saturation are adj ust abl e. Video Generating, The PAL/NTSC multi-s yst em col orbar video generator (seven-sys tem switchabl e, transmit/ recei ve seven-s yst em col orful imagi nes ) Dat a analys t. Capt ures and analyzes RS485 controlling dat a to hel p the techni ci an to find out the probl em. Cabl e testi ng. It is powerful in testi ng LAN cable, measuring the connect ing status ,displ ayi ng the sequence of connect ion and the NO. of the LAN cabl e. Multi-i nt erface and Multi -baudrat e. Support RS232 ,RS485 and RS422 interface; baud rat e rangi ng from 150, 600 to 19200bps. Multi -protocol. Supports more than twent y PTZ prot ocol s. For exampl e, PELCO-P, PELCO-D, SAMSUNG et c. PTZ address scanning, search up the ID of PTZ camera. Lithium Ion Polymer Batt er y (3.7V DC2000mAh). The devi ce employs advanced power control and prot ect ion ci rcuit. The devi ce is high power-e ffi ci ent , energy savi ng and environm ent al prot ecti on. It can last 11 hours for norm al use aft er charging for 4 hours. 2.2 s CCTV testerPRO Kit Kits Page.4. Ver: STP28V1.1 CCTV testerPRO User User’’s Manua Manuall Professi onal design, light and port abil ity, video display and dat a cont rol are delibe rat el y integrat ed, whi ch makes the instrument so simple, practi cabl e, easy for use that the training is almost unnecess a ry for an operator to be skill ful. 1. CCTV test erPRO 3. LAN Cabl e Tester 5. BNC Cabl e 6. Safet y cord 7. RS485 dat a cabl e 2. Power Supply (5V 2A) Ver: STP28V1.1 4. Lithium Ion Polymer Batt ery 8. Inst ructi on Manual Page.5. CCTV testerPRO User User’’s Manua Manuall 2. 3 Fr o n t Pa ne l 1 The power indi cator: it lights green whil e the test er is powered on. 2 The dat a-recepti on indi cator: it lights red whil e the dat a is bei ng recei ved. The dat a-transmissi on indi cator: it lights red whil e the dat a is bei ng 3 transmit ted The charge indi cator: it lights red whil e the batt ery is bei ng charged. As 4 the charging is com plete, the indi cator turns off aut omatically. 5 The displ ay Icon of batt ery el ectri cit y: it displ ays the el ectri c quantity 6 Main-m enu: it shows main functi ons of CCTV test erPRO. Page.6. Ver: STP28V1.1 CCTV testerPRO User User’’s Manua Manuall Sub-m en u: Shows and sets the val ues of functi ons 7 Long-pressing it more than 2 seconds to turn on/off the test er; short 8 pressi ng to turn on/off the PTZ controll er menu displ ayi ng. Menu key: it pops up the main-menu; const ant -press it or press the 9 or key can shi ft bet ween functi ons Setup key : press it or press left or right key to ent er sub-menu to set the 10 parameters of functi ons. Upward : Sel ect the item whi ch will be set or add the val ue of the 11 parameter. Tilt the PTZ upward. Leftward : Ent er the sub-menu or sel ect the parameter whose val ue will be 12 changed. Reduce the val ue of the parameter. Pan the PTZ left. Rightward : Ent er the sub-menu or sel ect the parameter whose val ue will 13 be changed. Add the val ue of the parameter. Pan the PTZ right. Downward : Sel ect the item whi ch will be set or reduce the val ue of the 14 parameter. Tilt the PTZ downward. Confirm/Open : Confirm the setti ng of parameters; open the ape rture . 15 Return/Cl ose : Return or cancel whil e setti ng parameters of the menu; 16 close the ape rture 17 Nea r focus: Focus the image nea rby. 18 Far focus: Focus the image faraway. 19 TELE: zoom in the image 20 WIDE: zoom out the image 2. 4 Si d e v ie w Ver: STP28V1.1 Page.7. CCTV testerPRO User User’’s Manua Manuall Left Side Top View Right Side 22 Reset the default setti ngs of parameters . 23 Ext ernal power suppl y (DC, 5V): It is highl y recomm ended to use the equipped power adapt er. 24 UTP cabl e port: Please use together with UTP LAN cable test er. 25 RS232 interface: RS232 comm uni cation for the PTZ. 26 Video input (BNC input interface): Inputs the video. 27 Video output (BNC output interface): Outputs the video. 28 RS485/422 Int erface: RS485/RS422 comm uni cation for the PTZ. 29 Hol e for the safety cord. Page.8. Ver: STP28V1.1 CCTV testerPRO User User’’s Manua Manuall 2. 5 Ins ta l l i n g th e Ba t te r y The test er has built -in lithium ion polym er rechargeabl e batt ery. The batt ery cable inside batt ery cabin shoul d be disconnec ted for safety duri ng transport ation! Prior to the use of the instrum ent, the batt ery cables inside the batt ery cabin shoul d be well connect ed and the color of cables shoul d be at the same side. Usual ly it need not to disconnect the cable at the norm al use, pressi ng key continuous ly can power on or off the test er. At the first time of use, the batt eri es shoul d be compl et ely exhaust ed and then rec harged for 4 or 5 hours. The Charge Indi cator lights red when charging the batt ery, The charge indicat or turns off autom ati cally when the charging is com pleted. △ Noti ce: When the Charge Indi cator turns off, the batt ery is approxim at el y 90% charged. The charging time can be ext ended for about 1 hour and the charging time within 8 hours will not dam age the batt ery. △ The test er can work as usual whil e it is bei ng charged , however. But the charging time will be ext ended. Press the RESET key at the right of the instrument to rest ore the default settings when the instru ment works abnormal ly. Unloc k the battery cover by pushing hori zon tall y as the direction illustrated Ver: STP28V1.1 Page.9. CCTV testerPRO User User’’s Manua Manuall Warning: Connect the termi nal of the batt ery with the direction illust rated. Please take care of the polarity of terminal. (The wires of the sam e color shoul d be both at the one side) Lock the batt eri es by pressi ng as the direction illust rated Page.10. Ver: STP28V1.1 CCTV testerPRO User User’’s Manua Manuall 3. Operation 3 .1 Pow er on Continuously press (at leas t 2 seconds) to power on/off the CCTV test erPRO. When the CCTV test erPRO is powered on,press MODE key the main-m enu will pop up. Menu & Func tions Press MODE key continuousl y or press the or key to sel ect the function (PTZ controll er, Video setti ngs, Colorbar generator, LAN cabl e test er, Dat a monitors, Devi ce setti ng) and ent er corres ponding function setti ng sub-menu. Press SET key to set the param et ers in functi on sub-menu. Not e: When the CCTV test erPRO is powered on, it will ret urn to the function whi ch is bei ng operat ed before it is turned off. 1. PTZ con troll er Displ ay the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the controlling parameters like prot ocol, comm uni cation port, baud rate, PTZ ID, pan/til t speed ; set and call prese t positi on. Ver: STP28V1.1 Page.11. CCTV testerPRO User User’’s Manua Manuall 2. Video settin g Adjust the LCD brightness, Contras t, Color saturation. 3. Colorbar gen erator Output or recei ve seven different forms of video col or bar to test er monitor, cabl e or other equipm ent. 4. Cabl e tester Test LAN cabl e or tel ephone cabl e. The connect ing condition and the sequence of wires will be displ ayed, as wel l as the seri al numbe r of the cabl e test er kit. 5. Data Moni tor Capt ures the prot ocol from the controlling syst em and displ ay comm and dat a. It is hel pful to debug and maint ai n RS485 comm uni cation. 6. Devi ce settin g Set the parameters of the CCTV test erPRO (Auto poweroff/ Keypad tone/Language/ Brightness ) Page.12. Ver: STP28V1.1 CCTV testerPRO User User’’s Manua Manuall 3.2 PTZ Controller Displ ay the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the controlling param et ers like protocol, comm uni cation port, baud rat e, PTZ ID, pan/ti lt speed ; set and call prese t positi on. The foll owi ng connecti ons shoul d be confi rm ed before use a. The Video In interface of the CCTV test erPRO and the output interface of camera b. Dat a A+ of the CCTV test erPRO and A+ of the PTZ camera or controlling devi ce, dat a B- of the instru ment and B- of the PTZ camera or controlling device Not e: Don ’t connect communicati ons interface with a circuit the voltage higher than 6V. a. Press SET key to ent er the sub-menu of PTZ controll er. b. Press the or key to sel ect the param et er whi ch we want to change the val ue. c. Press ENTER key to save the change or press RETURN key to give up the change d. Press SET key to exit the sub-menu. e. Press POWER key to full -sc reen the image Ver: STP28V1.1 Page. 13. CCTV testerPRO User User’’s Manua Manuall l: A. Protoco l: Select the protocol according to the protocol of the PTZ camera. Up to 21 popul ar protocol s are avail abl e, like elco P, Pelco D, Samsung, Yaan, LiLin, CSR600 et c. B. Port Port:: Select the communi cation port for the PTZ camera controlling (RS232/ 422/ 485) C. Baud: Select the baudrat e according to baudrat e of the PTZ camera.(150 , 300, … , 19200bps) D. Address : Set the ID acco rding the ID of PTZ camera (0~254 ). E . Pan Speed: Set the pan speed of PTZ camera (0~63) F. T iltSpeed: Set the tilt speed of PTZ camera (0~63) G. S et PS: Setup preset position (0~128) a. P/T/Z the camera to desi red positi on b. Press SET key to ent er PTZ cont roll er subm enu c. Move the yell ow cursor to “Set PS” and then press or key to select the prese t position number. d. Press ENTER key to compl et e preset position setti ng or prese t RETURN key to give up prese t position setti ng. Tips: Press or key to accel erat e the value changing. H. Go PS: Call the prese t positi on. (0~128) The PTZ camera will go to the desi red prese t positi on. a. Move the yell ow cursor to “Go PS” and then press or key to sel ect the preset position number. b. Press ENTER key to compl et e preset position calling or prese t RETURN key to give up prese t position calling. Tips: Press or key to accel erat e the value changing. The way of calling the OSD menu and prese t of the PTZ camera may vary with cont rol system s from different manufacturers. Please rea d the operation manual of cont rol syst em manufact urer for det ail s . The way of calling OSD provided for reference is calling preset -64. a. Move the yell ow cursor to “PTZ controll er ” to ent er PTZ cont roll er mode b. Press SET key to ent er PTZ cont roll er sub-menu. Press the yell ow cursor to “Go PS”, Page.14. Ver: STP28V1.1 or key to move CCTV testerPRO User User’’s Manua Manuall c. Press or key to sel ect the preset number 64, and then press ENTER key to call OSD menu of the PTZ controll er. OSD Menu of Dome (For ref eren ce only) MAIN MENU MAIN MENU 1. DISPLAY SETUP 1. Displ ay confi gurat ion 2. CAMER A SETUP 2. Set camera parameters . 3. CONTROL SETUP 3. Set PTZ controlling 4. CAMER A MASK SET 4. Set privacy mask 5. PROGR AM 5. Set aut o-running functi ons 6. PAL CAMER A 6. PAL/NTSC Switch 7. CAM DEFAULT SET 7. Restore the default setti ngs 8. DOM E RESET 8. Reset the dom e 9. EXIT 9. Exit the main menu Operate auto- running functions by call ing prese t position (effecti ve for some brands of PTZ camera) Call preset -33—Open Auto-fli p functi on Call preset -34—Reset zero point of PTZ camera Call preset -64—Enter the main menu of the PTZ camera Call preset -95—Enter the main menu of the PTZ camera or stop the PATTERN recording. Call preset -96—Run patt ern-1 Call preset -97—Run prese t tour-1 Call preset -98—Run fram e Scan Call preset -99—Run Auto scan 3.4. Video Setting Ver: STP28V1.1 Page. 15. CCTV testerPRO User User’’s Manua Manuall User can customize the brightness, contras t and saturation of the LCD according to the using environm ent and displ ay the form at(PAL/ NTSC) of video input. a. Press the or key to sel ect the param et er whi ch we want to change the val ue. b. Press the or key to change the val ue. Press ENTER key to save the change or press RETUR key to give up the change 3.5. Colorbar generator (Out put video at any mode) Output or recei ve seven different forms of video col or bar to test monitor, video cabl e or other equipm ent . 3. 6 a. Press the or key to sel ect the param et er whi ch we want to change the val ue. b. Press the or key to change the val ue. c. Press ENTER key to save the change or press RETURN key to give up the change er Cable Test Tester Test LAN cabl e or tel ephone cabl e. Connect LAN cabl e or tel ephone cabl e with the CCTV test erPRO and cabl e test er. And then the connect ing stat us, cabl e type and the sequence of wires will be displ ayed, as wel l as the seri al numbe r of the cabl e test er kit Page.16. Ver: STP28V1.1 CCTV testerPRO User User’’s Manua Manuall The right picture shows line1-7 are closed, line8 is open and the number of the cabl e test er box is 255 Straigh t-through Line Cross Line Open Line or Short Line 7 . Data monitor 3.7 3. Capture the comm and dat a from RS485 controlling syst em. a. Connect the RS485 or RS232 interface of controlling syst em with the RS485 or RS232 interface of the CCTV test erPRO (In case of RS485, A to A, B to B) b. Press SET key and then press Ver: STP28V1.1 or key to select comm uni cation port according to Page. 17. CCTV testerPRO User User’’s Manua Manuall the syst em connect ion. Press SET key to save the change. c. Press or key to sel ect the baud rat e according to the baud rat e of controlling syst em and then press SET key to save the change and capture comm and dat a from controlling syst em. d. Press RETURN key to clea r the scree n. 8 Device setting 3.8 3. Set the parameters of the CCTV test erPRO Auto poweroff: Setting the time of aut o shut -down.( Disabl e,5,10, …,60) Disabl e: Disabl e the “Auto poweroff” functi on. 5 means the CCTV will power off after 5 minut es when there is no any operation. Keypad tone: Open or close the beep of pressi ng key pad. Language: Sel ect languag e of OSD menu Brigh tness: Setting the brightness of OSD menu and background.(0~7) a. Press or b. Press or key to move the param et er we want to change. to change the val ue . c. Press ENTER to save the change or press RETURN key to give up the change. 9 PTZ address scanning 3.9 3. Search up the ID of PTZ camera. Note: Please isol ate the PTZ camera with other PTZ cameras before searching up. Otherwise all the PTZ cameras in the sam e syst em will pan at the sam e time. Press Page.18. keys to “Devi ce setti ng” Ver: STP28V1.1 menu: CCTV testerPRO User User’’s Manua Manuall Press key to confi rm aft er change “Address search:” to “on”, whi ch add address scan sub- menu. Press to swit ch the sub-menu as illust rated : Note: The syst em returns to “OFF” aft er shutdown, and the (Note: scan sub-menu closes aut omatically. Set “ON” again for next use.) Press key to set: prot ocol , communi cation port, comm uni cation rat e, make them same as the PTZ camera Press or NEAR: key, the address values is const antly on the rise or dec reas e. The test er will search up the ID quickl y and continuousl y(from 1 to 256). When the ID is searched, the PTZ camera will pan right. At this time, please press any key to stop searching up. FAR: The test er will search up the ID quickl y and continuousl y(from 256 to 1). When the ID is searched, the PTZ camera will pan left. At this time, please press any key to stop searching up. WIDE: The test er will search up the ID step by step (from 1 to 256). When the ID is searched, the PTZ FAR: camera will stop panning. The test er will search up the ID step by step (from 256 to 1). When the ID is searched, the PTZ camera will stop panning. Press button, the test er will search up the ID quickl y and continuousl y(from 1 to 256). When the ID is search ed, the PTZ camera will pan right. At this time, please press any key to stop searching up. Press manual single-s t ep dec reasi ng button, the test er will search up the ID step by step (from 256 to 1). When the ID is searched, the PTZ camera will stop panning. Press button , the test er will search up the ID quickl y and continuousl y(from 256 to 1). When the ID is search ed, the PTZ camera will pan left. At this time, please press any key to stop searching up. Ver: STP28V1.1 Page. 19. CCTV testerPRO User User’’s Manua Manuall Press manual single-s t ep increm ental button,the test er will search up the ID step by step (from 1 to 256). When the ID is searched, the PTZ camera will stop panning. Press the direction cont rol button to adjust Speed Dome Cam era. Press address-s canning function menu. Page.20. Ver: STP28V1.1 button to quit from the CCTV testerPRO User User’’s Manua Manuall 4. Specification MODEL CCTV Security Tester PRO Video Test Signal mode NTSC/PAL (Auto adapt ) 2.8 inch digital TFT-LCD ,960 x 240 resolution Displ ay LCD adj ustm ent Brightness, Contras t, Saturation adj ust abl e Video IN/OUT 1 channel BNC Input & 1 channel Output Video Output Mode 1.0 Vp-p PTZ controller Communication RS232, RS422 simplex and RS485 Compatibl e with more than 20 protocol s such as PELCO-D/ P, Samsung, PTZ Protocol Panasoni c, Lilin, Yaan, et c. Baud Rate 150,300,600,1200,2400,4800,9600,19200bps Video Signal Generation Color bar generation Output channel colorbar video signal for testing monitor or video cable UTP CABLE TEST Test UTP cable connection stat us and display in the screen . Read UTP cabl e test the numbe r of the test box. RS485 data analys t Data Monitor Captures and analyzes the command data from controlling device POWER Power Adapt er DC5V, 2A Battery Built-i n 3.7V Lithium polym er batt ery ,2000m Ah Rechargeable Low Consumption Aft er charging 3-4 hour, working time lasts 11 hours Energy saving technology General Working -3 0℃---+7 0℃ Temperature Working Humidity 30%-90% Dimension/Weight 166mm x95mm x48mm/293g The data above is only for ref eren ce and any change of them will not be informed in advance. For more detail ed techni cal inquiri es, please feel free to call the Technical D epartment of our company. Ver: STP28V1.1 Page. 21. CCTV testerPRO User User’’s Manua Manuall Products cer tif ication : Page.22. Ver: STP28V1.1