Download CFX- ACCKIT-16 Manual. - Easysecuritymarket.com

Installation Diagram
1 door Access control outdoor reader with 1200 lbs
Indoor electromagnetic lock
Model: CFX-ACCKIT-16
Reliable. Durable. Affordable
Power Supply
Reader
+
+
-
Exit Button
NC
Purple Wire From Reader
Electromagnetic Lock
+
Orange Wire From Reader
-
C
18/2 Guage Wire
-
QUICK TIPS:
.
.
.
.
.
Make sure to cut off the connectors on both power supplies, then strip wire leads before installing.
In order to properly install this kit it is recommended that you use 18/2 or 20/2 gauge wire.
Before installing this kit, check with your local fire Authority for the compliance of fire codes.
For Programming instructions, refer to the user manual of the reader.
Crosfox or it's Distributors are not ressponisble for any damage due to the improper installation off this kit.
Authorized Online Retailer:
Attachment: Advanced Application
1.SR-2400 operating as a Controller
In this mode the SR-2400 supports a Wiegand 26 bit input so an external
Wiegand device with a 26 bit output can be connected to the Wiegand input terminals
on the CFX-SR-2400 Either an ID card reader (125 KHZ) or an IC card reader
(13.56MHZ) can be connected to the CrosFox. Cards are required to be added at
the external reader, except where an externalEM reader is used, in this case cards
can be added at either reader or controller. See figure 1
Reliable. Durable. Affordable
J1
Green
D0
D1
White
D1
+12V
GND
SR-2400 controller
J1
D0
Green
D1
White
ALARM-
SR-2400 Quick reference Programming Guide
Function description
Choose from the relevant function below and input
Enter the programmingmode
* 888888 #
then you can do the programming
(888888 is the default factory master code)
To exit the programming mode
OPEN
Yellow
Brown
+12V
Red
GND
Black
VSS
Blue
LL+
ALARM+
*
+12V
DC12V/3A
+
Em card
Ic card
HID card
-
D0
Add card user
Delete card user
0 New code # Repeat New code #
(Code must be 6-8 digit numbers.)
1
Read Card
Read Card
Brown
D_IN
+12V
Black
GND
Blue
VSS
+
Purple
-
Orange
#
-
Grey
OPEN
Yellow
Brown
+12V
Red
+
Alarm
door detecting switch
Exit button
Green
D0
White
D1
Grey
ALARM-
Yellow
OPEN
Brown
D_IN
Red
+12V
GND
Black
Black
GND
VSS
Blue
Blue
VSS
Purple
L-
Orange
L+
ALARM+
LL+
ALARM+
Purple
-
Orange
+
Lock
SR-2400 controller 2
SR-2400 controller 1
figure 3
figure 2
Alarm
Purple
-
Orange
Lock
+
3. Two CFX-SR-2400 units interconnected for a single door
,
In this mode two SR-2400 units are us for a single,door
one for entry and the other for exit.
Either device acts as the controller and reader at the same time. Users can be
enrolled in either of the devices. In this mode the user capacity for one door can be
up to 20000. The setting of the two SR-2400 units must be the same including the
same including the master code.See figure 3
2.SR-2400 operating isa Wiegand Output Reader
In this mode the SR-2400 supports a Wiegand 26 bit Output so the Wiegand data lines
can be connected to any controller which supports a Wiegand 26 bit input. Seefigure 2
J1
D0
Green
D1
White
ALARMOPEN
Figure 1
4.Two CFX-SR-2400 units interconnected & interlocked for 2 doors
two doors I n t h i s m o d e t w o S R - 2 4 0 0 u n i t s a r e u s e d f o r t w o d o o r s which
are then interconnected and interlocked.In this mode the doors canbe interlocked so
that when door 1 is open,door 2 cannot be opened, and vice versaThe interlocked
SR-2400 controller 2
SR-2400 controller 1
Power
DC12V/3A
Door 1
-
Grey
Brown
+12V
Red
+
+
Yellow
D_IN
Door 2
-
+
Alarm 2
Alarm 1
door detecting switch 1
Exit button 2
Exit button 1
J1
Green
D0
White
D1
Grey
ALARM-
Yellow
OPEN
Brown
D_IN
Red
+12V
Black
Black
GND
VSS
Blue
Blue
VSS
-
Purple
L-
+
Orange
L+
ALARM+
L-
Purple
-
Orange
+
Lock 1
5.1 Set the needed function and enroll the User Cards on the inside SR-2400
Anti-submarine Master unit.
5.2 With the valid user card, the user can only enter the door from the outside reader,
and exit from the inside SR-2400 Controller.Onthe other hand, without entering record
from the reader,the user can't exit fromthecontroller inside, also,the user can'tenter
in twice without the first exit record, and vice versa.
Anti-submarine function for 2 doors
The connection diagram is as Figure 4. Door 1 with one SR-2400,and Door 2 with one,
SR-2400 set one SR-2400 on Door 1 as the Anti-submarine Auxiliary(3 2 unit # ),
and set the other SR-2400 on Door 2 as the Anti-submarine Master unit (3 1 #).
They build up a anti-submarine system, which is normally used for parking lot......etc.
Lock 2
6.2 With the valid user card, the user can only enter in from Door 1, and exit from Door 2.
On the other hand, without entering record from the Auxiliary unit, the user can't exit
from the Master unit or Auxiliary unit , also, the user can't enter in twice without the first
exit record, and vice versa.
function is mainly prisons,and other places where a higher levelof securityis required.
User manual
See figure 4
Read user card
figure 4
.6.
.7.
.8.
.9.
CFX-SR-2400 Waterproof
Standalone Proximity Reader
door detecting switch 2
GND
L+
ALARM+
Reliable. Durable. Affordable
The operation and function is as below:
6.1 Set the needed function and enroll the User Cards from SR-2400
Anti-submarine Master unit on Door 2.
door detecting switch Exit button
#
( Can delete card continuously)
White
D_IN
LL+
ALARM+
Green
+
To Unlock the door
To Unlock the door
D1
ALARM-
-
( Can add card continuously)
2
ALARMOPEN
Controller with wiegand 26 input
reader plug
Note: that to undertake the following programming the master user must
enter into the programming mode
Change the master code
Grey
J1
-
+
D1
Grey
D_IN
Power
wiegand reader
GND
Powerful supply
D0
outdoor
DC12V/3A
J1
Yellow
Red
Controller
Power
Indoor
D0
5. Anti-submarine function for single door (3 1 #)
The connection diagram is as figure 1. Install one Wiegand reader (or a SR-2400 without
user information as reader) outside the ,door,connecting to one SR-24000 Controller
inside the door,which acts as the Anti-submarine Master unit. of the two devices, they
build up an anti-submarine system for single door.The operation and function is as
below:
.10.
1. Packing List
Name
Specification
Quantity
SR-2400
1
Standalone Proximity Reader
Infrared remote control
1
Manager card
One for add, one for delete
2
Used for factory default setting
1
User manual
SR-2400
1
Self Tapping Screws
3.5*27mm
4/2
Short Pin
A
C
61mm
95.5mm
2. Description
The SR-2400 is fully waterproof standalone Proximity access Reader, which uses advanced
microprocessor, equipped with large capacity Flash memory,supports up to 10,000 cards. It
is so easy to add or delete card users by using the master card, besides, with Infrared remote
control programmerthe user can set the features
by themselves, including Alarm, Self-protection,
,
interlock and Anti-submarine back Function. In additional, with infrared remotecontrol interlock
and Anti-submarine back Function. In additional, with infrared remote.
Shielded
cables
D
6. Wiring
No
Color
Function
Description
Green
D0
2
White
D1
Wiegand output, input signal wire D1
3
Grey
ALARM+
connecting to the negative pole of the alarm equipment
4
Yellow
OPEN
To connect to one part of Exit Button
5
Brown
D_IN
Door Contact input
6
Red
12V
(+) 12Vdc Positive Regulated Power Input
<15mA
Humidity
20%
98%
7
Black
GND
(-) Negative Regulated Power Input
125KHZ EM card
Lock output load
Max20A
Alarm output load
Max20A
8
Blue
VSS
the negative pole of the controller, connect to the other
part of Exit button and door contact
Wiegand interface
Wiegand 26
Manager card
Two
User capacity
10,000
Dimensions
103 x 48 x 23mm
.1.
D_IN
Brown
Red
when alarm, the I/O outputs high level.
+12V
4-low level
5-high level
L-
ALARMI/O
Q6
To Delete User by Manager Card
R20
R19
Figure 1
Purple
-
Orange
+
To Enter the programming mode
NOTE:The above diagrams show the output interface circuits. Unlike most lock and
alarm outputs which use a relay that can be shocked or magnetized,the SR-2400 uses
MOS outputs for both the Lock Output on the left and the Alarm Output on theright.
Blue
9
Purple
10
Orange
LL+/Alarm+
Green
D1
White
ALARM-
Lock
Power off, use the supplied Contact Pin to short out the 2P socket on the mainboard,
then power on, if successful, the beeper will beep twice, the LED shines in orange,
remove the Short Pin, then read any two EM cards, after that the LED turns in red,
means reset to factory default setting successfully. of the two EM cards read, the first
one is Manager add card, the second one is Manager delete card.
Yellow
D_IN
Brown
+12V
Red
GND
Black
VSS
Blue
L+
ALARM+
Alarm
+ -
.2.
PUSH NC COM NO
Remarks: Reset to factory default setting, the users' information enrolled is still retained.
When reset to Factory default setting, the two Manager cards must be re-enrolled.
Purple
Orange
Special Power Supply
Do not power on until all wiring has been completed
.3.
add card Cards can be added continuously.
Manager delete card Read user card Manager
Delete ca rd Cards can be deleted continuously.
LED
Buzzer
Reset to factory default setting
Orange
Two short ring
Sleeping mode
Red shines slow
Short ring
Operation successful
To change the master code
To add a card user (Method 1)
To add a card user(Method 2)
To delete a card user
Manager Cards. Be careful with use)
Operation status
* Manager Password #
888888 is the default factory master code
Remarks: All the steps below must be done after entering into programming mode
To delete ALL users.
( Note: This option will delete all users but
9. Sound and Light indication
door detecting switch
Connect to the negative pole of the Lock
Connect to the positive pole of the lock and alarm equipment
DC12V/3A
Grey
OPEN
L-
Exit button
Manager add card Read user card Manager
B- By Remote control
door detecting switch
Black
D0
A - By Manager card(The most convenient way)
To Add user by Manager Card
0 New Password # Repeat New Password #
The master code must be 6 8 digit number.
1 Read Card #
Card can be added continuously without
exiting programming mode.
1 Input Card number (8 digit)
#
The card number is the last 8 digits of the
number printing on the card.
2
Read Card # or
2
Card number (8 digit)
2
0000
#
#
Enter into setting
Orange shines
Short ring
Exist from programming mode
Red shines slow
Short ring
Fail secure (Unlocked when power on)
This is the factory default, 3 seconds:
4 0 99 #
0-99 is to setthe door relay time0-99 seconds.
Fail safe (unlocked whenpower is off)
5 0 99 #
0-99 is to setthe door relay time0-99 seconds.
Short ring
Alarm
Red shines fast
Alarm
.4.
3 2 #
Advanced application ) .
Door open detection
Door Open Too Long (DOTL) warning. When used with an optional magnetic
contact or built-in magnetic contact of the lock, if the door is opened normally, but
not closed after 1 minute, the inside buzzer will beep automatically to remind
people to close the door and continue for 1 minute before switching off
automatically.
Door Forced Open warning. When used with an optional magnetic contact or built in
magnetic contact of the lock, if the door is forced open, or if the door is opened after
120 seconds of the electro-mechanical lock not closed properly, the inside buzzer
and alarm output will both operate.
To disable door open detection.
(Factory default)
6
0
#
To enable door open detection
6
1
#
Security Mode Setting
Reader Lockout & Alarm Output options. If there are 10 invalid cards within 1 0 mi nut es,
the Reader will lockout for 10 minutes or the alarm will operate for 10 minutes,
depending on the option selected below.
Normal status (No lockout or alarm)
7 0
# (Factory default setting)
Reader Lockout
7 1
#
Alarm Output
7 2
#
Door interlock disabled
8 0
#
Door interlock enabled
8 1
#
Alarm output time
Toremove the doorforced open warning
Lock Power Setting
Three short ring
Antisubmarine Auxiliary Mode
(Factory default)
9 0~3
#
To remove the alarm
10.2 Door setting
Short ring
Green shines
3 1 #
To set the alarm output time (0-3
minutes) Factory default is 1 minute
Red shines
Open the door
3 0 #
Anti-submarine Master Mode
Door Interlock.
Enter into programming mode
Operation failed
Anti-submarine Disabled
( Note: the detailed wiring diagram and illustration, please refer to the
B - By remote control
R8
Q2
R7
There are 2 ways to add and delete users:
A - By manager card;
L+
D6
I/O
Fail-securelock
1
Wiegand output, input signal wire D0
60
10cm
-
40mm
-20
Card Reading Distance 5
+
By programme setting, I/O
switch between low level and
high level.
8.To Reset to Factory Default and Manager Card setting
Temperature
Card type
Yellow
L+
ALARM+
DC12V/3A
+
10.1 User settings
Alarm Interface Principle:
Lock Interface Principle:
Grey
OPEN
+12V
Alarm
Fail-safe lock
4. Specifications
Sleeping Current
White
Exit button
J1
Can be used as salve reader
2 pcsW can be interconnected/ interlocked
Can be used as controller by connecting
slave reader
Anti-submarine back Function
Alarm signal output,Door open detection
Full of 10,000 users, recognizing speed <15ms.
10%
D1
L-
3. Features
DC12V
Green
VSS
The SR-2400 not only has the features of low power consumption, automatic selection of lock
anti vandal alarm and exit button, ut also has the protective functionsagainst input over voltage
and outputs short-circuit.These features make the SR-2400,reliablend easy in operation. It is
an ideal choice for door access.
Supply Voltage
J1
GND
B
Common Power Supply
D0
10. SR-2400 Detailed Programming Guide
7. Interface Circuits
SR-2400
ALARM-
Please ensure that all the above contents are correct. If any are missing, please notify the supplier of the
SR-2400.
Standalone Card Reader
User capacity: 10,000
Card interface: 125KHZ EM Card
Remote control for programming
With Manager cards for fast add
and delete users
Wiegand 26 input/output
Connection Diagram
5. Installation
Drill holes on the wall or prepare the cassette.
Wire through the hole,and blanket the unused cable in case of short circuit.
Fix the back cover firmly on the cassette or the wall.
Attach the reader to the back cover.
Anti-submarine Settings
.5.
To remove the door open too long
warning
Read valid card or Master Code #
Close the door or Read valid card
or Master Code #
To Unlock the door
To Unlock the door
Read user card
Note:that Manager Card can'tbe used to unlockthe door.
.6.
I
NSTALLATI
ONMANUAL
El
ect
r
omagnet
i
cDoorLock1200l
bsWi
t
hLEDandUL
MODELNUMBER:
CFXEL1200
Cor
yr
i
ghtCROSFOX
Al
lRi
ght
sReser
ved2012
I
NSTALLATI
ONMANUAL
I
LLUMI
NATEDVANDALRESI
STANTPUSHTOEXI
TBUTTON
MODELNUMBER:CFXRDBEB5004
Lengt
h(
A)
:114.
0mm
Wi
dt
h (
B)
:69.
40mm
Dept
h (
C)
:5.
4mm
Lengt
h(
A)
:4.
48I
nch
Wi
dt
h (
B)
:2.
73I
nch
Dept
h (
C)
:0.
21I
nch
PUSHTOEXI
TBUTTONWI
RI
NG DI
AGRAM:
(
1)Pushbut
t
ondr
ycont
actr
at
i
ng:
5A/125VAC
Forsaf
eoper
at
i
ons,donotexceedt
her
at
i
ngsabove.
(
2)ForNor
mal
l
y open r
equi
r
ement
s,connectwi
r
est
o
N.
O dr
ycont
actofPUSHBUTTON
(
3)ForNor
mal
l
ycl
osedr
equi
r
ement
s,
connectwi
r
et
o
N.
Cdr
ycont
actofPUSHBUTTON
Wi
r
eCol
or
:
+ :Red
- :Bl
ack
N:
O:Yel
l
ow
N:
C:Bl
ue
COM:Gr
een
BOTTOM VI
EW