Download 6zx7 user`s manual
Transcript
6ZX7 USER'S MANUAL 1. System power on by PS/2 Mouse: First, enable this function in CMOS Setup, then you can power on the system by double clicking the right or left button of your PS/2 Mouse. 2. System power on by Keyboard: If your ATX power supply supports larger than 300 mA 5V Stand-By current (depends on the specification of keyboards), you can power on your system by entering password from the Keyboard after setting the “Keyboard power on” jumper and password in CMOS Setup. 3. Support 3 steps ACPI LED selectable. 4. Support Modem Ring-On. (Include internal Modem and external modem on COM A and COM B) 5. Support Wake-up On LAN. (Your ATX power supply must support larger than 720 mA 5V Stand-By current) CeleronTM Socket 370 Processor MAINBOARD REV. 1.4 First Edition R-14-01-090729 6ZX7 The author assumes no responsibility for any errors or omissions which may appear in this document nor does it make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners. Sound Blaster is a registered trademark of Creative Technology Ltd in the United States and certain other countries. Sound Blaster-LINK and SB-LINK are trademarks of Creative Technology Ltd. July 29, 1999 Taipei, Taiwan 1 Quick Installation Guide I. Quick Installation Guide : The system bus speed can be set for 66/100 MHz. The user can select the system bus speed (SW2) and change the DIP SWITCH (SW1) selection to set up the CPU speed for 366 - 566MHz processor. M The CPU speed must match with the frequency RATIO. It will cause system hanging up if the frequency RATIO is higher than CPU's. SW1: (O:ON / X:OFF) DIP SWITCH (SW) FREQ. RATIO 1 2 3 4 X3 O X O O X 3.5 X X O O X4 O O X O X 4.5 X O X O X5 O X X O X 5.5 X X X O X6 O O O X X 6.5 X O O X X7 O X O X X 7.5 X X O X X8 O O X X X 8.5 X O X X X9 O X X X X 9.5 X X X X 2 6ZX7 Set System Bus Speed SW2: (O:ON / X:OFF) CPU AGP 1 2 3 4 66 66 O X X O 75 75 O O X O 83 83 O X O O 100 66 X X X X 112 75 X O X X 133 89 X X O X « Note: We don’ t recommend you to set up your system speed to 75,83,100,112 or 133MHz because these frequencies are not the standard specifications for CPU, Chipset and most of the peripherals. Whether your system can run under 75,83,100,112 or 133MHz properly will depend on your hardware configurations: CPU, SDRAM, Cards, etc. + The black part in the picture is the white extruding piece of the DIP switch. 1. CeleronTM 366/ 66 MHz FSB CPU OFF ON OFF ON 1 2 3 4 1 2 SW1 SW PIIX4 1 3 4 6ZX7 3 SW2 INTEL 82443BX SW 2 Quick Installation Guide 2. CeleronTM 400/ 66 MHz FSB OFF ON OFF ON 1 1 2 2 3 3 4 4 SW2 SW1 3. CeleronTM 433/ 66 MHz FSB OFF ON OFF ON 1 1 2 2 3 3 4 4 SW2 SW1 4. CeleronTM 466/ 66 MHz FSB OFF ON OFF ON 1 1 2 2 3 3 4 4 SW1 SW2 4 6ZX7 5. CeleronTM 500/ 66 MHz FSB OFF ON OFF ON 1 1 2 2 3 3 4 4 SW2 SW1 6. CeleronTM 533/ 66 MHz FSB OFF ON OFF ON 1 1 2 2 3 3 4 4 SW2 SW1 7. CeleronTM 566/ 66 MHz FSB OFF ON OFF ON 1 1 2 2 3 3 4 4 SW1 SW2 5 Quick Installation Guide II. Jumper setting : SPK : Speaker Connector CPU External Speaker + 1 SW1 PIIX4 PIIX4 PIN No. Function 1 VCC SW2 INTEL 2 82443BX 82443ZXNC 3 NC 4 Data 6ZX7 Buzzer RST : Reset Switch CPU PIN No. Function Open Normal Operation Close Reset 82443BX Hardware INTEL 82443ZX SW1 System PIIX4 PIIX4 6ZX7 6 SW2 6ZX7 PW LED : Power LED Connector CPU + − − PIIX4 PIIX4 PIN No. SW1 1 2 3 6ZX7 Function INTEL 82443BX LED +82443ZX LED − LED − SW2 HD : IDE Hard Disk Active LED CPU SW2 + PIIX4 PIIX4 − INTEL 82443BX 82443ZX PIN No. Function 1 LED + 2 LED − SW1 6ZX7 7 Quick Installation Guide GN : Green Function Switch CPU PIIX4 PIIX4 PIN No. Function82443BX INTEL 82443ZX Open Normal Operation SW1 Close Entering Green Mode SW2 6ZX7 GD : Green LED CPU SW2 − PIIX4 PIIX4 + PIN SW1 No. Function 1 LED + 2 LED − 6ZX7 8 INTEL 82443BX 82443ZX 6ZX7 IR : Infrared Connector (Optional) 1 + CPU PIN No. Function 1 IR data output 2 GND 3 IR dataSW1input 4 PIIX4 PIIX4 NC 5 Power(+) SW2 INTEL 82443BX 82443ZX 6ZX7 Soft POWER : Soft Power Connector CPU PIN No. Function 1 SW1 Signal PIIX4 2 GND PIIX4 6ZX7 9 SW2 INTEL 82443BX 82443ZX Quick Installation Guide ATX POWER : ATX Power Connector 1 11 PIIX4 PIIX4 Pin No. 3,5,7,13, 15-17 1,2,11 4,6,19,20 10 SW1 12 18 8 6ZX7 9 14 Function GND CPU 3.3V VCC INTEL 82443BX +12V 82443ZX -12V -5V Power Good 5V SB stand by+5V PS-ON(Soft On/Off) SW2 PS/2 Mouse / Keyboard Connector CPU PS/2 Mouse SW1 PIIX4 PIIX4 PS/2 Keyboard PS/2 Mouse/ Keyboard Pin No. Function 1 Data SW2 2 NC INTEL 82443BX 3 GND 82443ZX 4 VCC(+5V) 5 Clock 6 NC 6ZX7 10 6ZX7 CPU FAN : CPU FAN Connector 1 PIN No. 1 2 3 Function CPU GND +12V SENSE SW2 INTEL 82443BX 82443ZX SW1 PIIX4 PIIX4 6ZX7 PWR FAN : Power FAN Connector CPU 1 PIN No. Function 1 GND 2 +12V INTEL 3 82443BX SENSE 82443ZX SW1 PIIX4 PIIX4 6ZX7 11 SW2 Quick Installation Guide SYSTEM FAN : System FAN Connector CPU 1 PIN No. Function 1 SW1 GND PIIX4 2 +12V PIIX4 3 SENSE SW2 INTEL 82443BX 82443ZX 6ZX7 IDE1: For Primary IDE port CPU SW2 INTEL 82443BX 82443ZX SW1 PIIX4 PIIX4 6ZX7 1 12 6ZX7 IDE2: For Secondary IDE port CPU SW2 INTEL 82443BX 82443ZX SW1 PIIX4 PIIX4 6ZX7 1 FLOPPY : FLOPPY PORT CPU SW2 INTEL 82443BX 82443ZX SW1 PIIX4 PIIX4 6ZX7 1 13 Quick Installation Guide LPT PORT / COM A / COM B LPT PORT CPU SW2 INTEL 82443BX 82443ZX COM B SW1 COM A PIIX4 PIIX4 6ZX7 JP1 : Keyboard Power On Selection CPU SW2 INTEL 82443BX 82443ZX SW1 PIIX4 PIIX4 6ZX7 14 6ZX7 USB : USB Port SW1 PIN No. 1 2 3 4 5 6 7 8 Function USB V0 USB D0- CPU USB D0+ GND USB V1 USB D1USB 82443BX D1+ INTEL GND 82443ZX SW2 PIIX4 PIIX4 6ZX7 JP7: Wake On LAN CPU SW2 1 2 3 PIIX4 PIIX4 PINSW1 No. 1 2 6ZX7 3 Function +5V SB GND Signal 15 INTEL 82443BX 82443ZX Quick Installation Guide JP9 : CLEAR CMOS FUNCTION 3 2 1 CPU PIN No. Function 1-2 close Clear CMOS SW1 2-3 closePIIX4Normal (Default) SW2 INTEL 82443BX 82443ZX PIIX4 6ZX7 J14 :SB-LINK PIN No. CPU 1 2 3 1 4 VT82C693 82443BX5 6 SW1 PIIX4 PIIX4 6ZX7 16 Function Signal GND NC Signal SW2 GND Signal 6ZX7 J16: Internal Modem Ring On CPU 1 PIN No. 1 2 PIIX4 PIIX4 Function Signal SW1 GND SW2 INTEL 82443BX 82443ZX 6ZX7 JP10 : CASE OPEN CPU 1 PIN No. Function INTEL 1 Signal82443BX 82443ZX SW1 2 GND PIIX4 PIIX4 6ZX7 17 SW2 Quick Installation Guide JP13/ JP14 : Close for Voodoo III JP13 CPU JP14 Open PIIX4 PIIX4 Short SW2 INTEL 82443BX PIN No. Function 82443ZX SW1 Open Normal (Default) Short Close for Voodoo III 6ZX7 VGA Card BAT1 :Battery MDanger of explosion if battery is incorrectly replaced. CPU MReplace only with the same or equivalent type recommended by the manufacturer. SW2 INTEL 82443BX 82443BX PIIX4 PIIX4 MDispose of used batteries according SW1 to the manufacturer’s instructions. + 6ZX7 18 6ZX7 III. Top Performance Test Setting: Users have to modify the value for each item in chipset features as follow for top performance setting. ** Each value of items as above depends on your hardware configuration : CPU , SDRAM , Cards , etc. Please modify each value of items If your system does not work properly . 19 Quick Installation Guide The following performance data list is the testing results of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users. (Different Hardware & Software configuration will result in different benchmark testing results.) • CPU Intel CeleronTM Socket 370 processor • DRAM (128x 1) MB SDRAM (TOSHIBA TC59S6408BFT-80) • CACHE SIZE 128 KB included in CPU • DISPLAY GA-630 AGP Display Card (16MB SGRAM) • STORAGE Onboard IDE (Seagate ST34520A) • O.S. Windows NT ™4.0 (SPK4) • DRIVER Display Driver at 1024 x 768 x 64K colors x 75Hz. Triones Bus Master IDE Drivers 3.60 Processor Intel CeleronTM (Scoket 370) 366MHz (66x5.5) 450MHz (100x4.5) CPU mark32 723 964 FPU Winmark32 1970 2410 Business Disk 4260 4510 Hi-End Disk 10300 10500 Business Graphics 176 222 Hi-End Graphics 330 409 Business 26.8 31.5 Hi-End 24.4 29 Winbench99 Winstone99 20