Transcript
APT-6S / APT-6SB WEEKLY PROGRAMMABLE TIMER User's Manual SAFETY PRECAUTION This manual uses the following symbols to ensure safe operation of this timer. Warnings are indicated when mishandling this controller might result in death or serious injury to user. Cautions are indicated when mishandling this controller might result in minor injury to the user, or only physical damage to the timer. WARNING CAUTION WARNING RESTRICTIONS ON USE When using this product in applications that require particular safety or when using this product in important facilities, please pay attention to the safety of the overall system and equipment. Install failsafe mechanisms, perform redundancy checks and periodic inspections and adopt other appropriate safety measures when it is necessary. This product is rated at Class ҈ . ΘNote this incorrect wiring of this controller can damage it and lead to other hazards. Make sure the controller has been correctly wired before turning the power ON. ΘBefore wiring, or removing / mounting the controller, be sure to turn the power OFF. Failure to do so might cause electric shock. ΘDo not touch electrically charged parts such as the power terminals. Doing so might cause electric shock. ΘDo not disassemble the controller. Doing so might cause electric shock or faulty operation. CAUTION ΘUse the controller within the operating ranges recommended in the specification (temperature, humidity, voltage, shock, mounting direction, atmosphere and etc.). Failure to do so might cause fire or faulty operation. ΘFirmly tighten the terminal screws. Insufficient tightening of terminal screws might cause electric shock or fire. ΘPress reset before use after removing the insulation sheet or replace the battery. SPECIFICATION BUTTON and SWITCH FUNCTIONS Operating voltage AC/DC : 12 ~ 48V / AC/DC : 100 ~ 240V Allowable operating voltage range 85 ~ 110% of rated operating voltage Rated frequency Θ : Porgram setting (ON/OFF) ΘOFF SET : Output contact is disabled 50 / 60 Hz ΘCLOCK : Current time setting ΘON Contact rating 240VAC 7A(N.O.), 240VAC 5A(N.C.) Resistive load Θʳ DAY : Weekday setting ΘAUTO : Output contact is controlled by Indicator operating POWER - Red / RELAY ON - Green Power consumption Approx. 3.3VA ΘʳʳHR : Hour setting Life Mechanical : 5,000,000 times / Electrical : 100,000 times Θʳ MIN : Minute setting Ambient temperature -10 ~ +50 °C program setting ϡWhen switch to Auto mode from ON or OFF, Γoutput contact will be kept in the previous Γmode. Than, output contact will be controlled Γby program setting. ΘCLEAR : Clear setting Ambient humidity MAX 85% RH Weight Approx. 170g Θ RESET : Program reset CONNECTION When APT and the load have separate power source : Output contact is enabled OPERATING FLOWCHART When APT and the load share the same power source N Type SU MO TU WE TH FR SA TU TU N Type CLOCK P ROGRA MM A B L E TIME R P R OGR A MMA B LE TI ME R DAY CLOCK SET WEEKDAY HR CLOCK SET HOUR MIN SET MINUTE SET CURRENT TIME SETTING SET DAY HR MIN SET AUTO ON CLEAR OFF CLOCK DAY CLOCK HR OFF RED MIN AUTO ON CLEAR OFF RESET ON GREEN ON OFF RESET APT - 6S ON GREEN OFF RED SE T APT - 6S SET SET PROGRAM NUMBER LOAD PROGRAM SETTING CLOCK ON SU MO TU WE TH FR SA SE T DAY ON MO SE T HR SET WEEKDAY SET HOUR ON MO SE T MIN SET MINUTE LOAD LOAD SOURCE N MO SE T CLEAR PROGRAM ENABLE OR DISABLEϡ ϡThe pervious setting will be L N SOURCE L shown when press SOURCE CLEAR once again. CONVERT Y TYPE (Flush Mounting) TO N TYPE (Surface Mounting) BATTERY CHANGE ᢳ ON ᢴ ᢳ ᢴ ᢵ Lithium battery CR2032 + 3 VOLTS CONVERT N TYPE (Surface Mounting) TO Y TYPE (Flush Mounting) BEFORE USE Insulation Sheet Pull Before Use Press reset before use after removing the insulation sheet ᢳ ᢴ ᢵ ᢶ PROGRAMMABLE TIMER SET DAY CLOCK HR MIN AUTO ON CLEAR OFF RESET ON GREEN OFF RED APT - 6S Reset ANLY ELECTRONICS CO., LTD. http://www.anly.com.tw M-APT6-L-B Printed in Taiwan