Download Declaration of Conformity Deklaracja Zgodności

Instrukcja obsługi laminatora OPUS cityLAM A3
Declaration of Conformity
Deklaracja Zgodności
OPUS Sp.z o.o. hereby declares that the machine specified below is in
accordance with the following directives and standards:
Opus Sp.zo.o. deklaruje z pełną odpowiedzialnością, że urządzenie, którego
dotyczy niniejsza deklaracja jest zgodne z postanowieniami następujących
dyrektyw UE oraz powiązanymi z nimi normami zharmonizowanymi:
2006/95/WE; 2004/108/WE
EN60950-1:2006+A12:2011; EN55014-1/A1:2009; EN55014-2/A2:2009;
EN61000-3-2/A2:2009: EN61000-3-3:2008
Name/ Nazwa:
OPUS Sp. z o. o.
Address/ Adres:
ul. Toruńska 8
44-122 Gliwice
Type of the machine / typ:
Laminator
Model No / model:
cityLAM A3
POLAND / Polska
(Place)
…………………………………
(Signature)
01.01.2013
(Date)
Krystian Nawrat
(Full Name)
5
User’s guide OPUS cityLAM A3
User’s manual
OPUS cityLAM A4
6
User’s guide OPUS cityLAM A3
Healht & Safety precautions:
●
Before operating the equipment please read the Health & Safety precautions, manufacturer
recommendations and the operation manual.
●
The operation manual should be easily available at any time for the operator.
●
The equipment should be installed on sturdy and level surface near a 220-240 V, 50Hz socket.
●
The equipment should be protected against dust and moisture
●
The equipment must not be placed near the heating or ventilation units.
●
The equipment must not be used in vicinity of inflammable liquids or gases
●
The power supply cable should be protected against damage and must not be used to pull the
equipment or to remove the plug from the socket.
●
The equipment must be kept away and out of from reach of children.
●
Danger! The equipment contains rotary elements. Ensure long hair, loose jewellery, ties and other
loose pieces of clothing are keep away they can be get entangled in the rolls.
●
The equipment must not be used for any other purposes than those indicated in the instruction
manual.
●
It is necessary to check and supervise if the equipment is operated correctly.
●
In case of any malfunctions, you must contact the dealer or service team.
●
The equipment must not be located outside and should be operated in a room temperature higher
than +8 °C.
●
Before removing any covers from the equipment, remove the power plug from a mains socket.
●
Using inappropriate lubricants causes a fire hazard.
●
Any repairs must be carry out only by authorised staff.
●
The equipment must be operated according to general Health & Safety rules.
●
Do not leave the equipment in operation without an operator.
●
After work it is necessary to turn the equipment off by the switch on unit after the cooling down
procedure, next remove the plug from a socket
Manufacturer’s recommendations:
●
Use only recommended supplies and accessories.
Do not put into the laminator documents thicker than 1 mm. The laminated material should always
have similar properties
●
Remove the mains plug from the socket before moving the equipment or during longer none
operation.
●
If the equipment is switched on and is not operated for more than one hour, it can be overheated.
To avoid bad quality lamination put 2 or 3 sheet of A4 paper through in order to cool the rollers
down
●
Always insert the laminating pouch with the close end into the laminator first. Putting the open
end first can cause bubbling and the film being stuck on the rollers inside the laminator.
●
In case of a document being stuck inside the laminator, use reverse function REV switch.
●
Tailor cut pouch can make the rollers sticky and dirty and wind round them use a carrier.
●
Remove all metal elements (staples & paper clips, etc.) before laminating the document.
●
NOTE! The equipment contains heater elements, be aware high temperatures!
●
NOTE! Not compliance with the rules and recommendations above can void the
Guarantee/Warranty.
●
7
User’s guide OPUS cityLAM A3
Operation:
1. Starting the equipment :
• Plug the equipment into the power socket and turn on by pressing the button
• Press the buttons on the touch panel to setup the thickness of pouch required from the range
of foil thicknesses from 80mic – 200mic. The process of heating will start automatically.
• The heating time for the laminator rollers is 4-6 minutes. during this time on LCD display the
red diode.
• When laminator is ready the green diode flashes. The equipment is now ready to use.
2. Preparing the document :
• Choose correct thickness and type of pouch. Put the document into the pouch.
NOTE! It is recommended to leave approx. 3mm margins all around the document
from the edge.
3. Hot lamination
• Open the flap at the back of equipment, insert the laminating pouch from the front with the
document inside it into the rollers, and remember to put the sealed end first.
• The pouch/document will move through the unit and exit at the back.
• If the lamination is not good you can repeat laminating or change settings
• After one hour in “stand by” mode the machine will turn off automatically
4. Cold lamination
• Plug the equipment into the power socket and turn on by pressing the button. Choose proper
option on display for „cold lamination”
• After hot lamination wait 40-60min to cool down the equipment before you start to cold laminate.
Maintenance and service:
• Before clearing the equipment, remove the power plug from the socket.
• If the pouch was entangled into the rollers or the laminator does not operate correctly contact
the dealer or service team
• Push and keep “REV” button when the laminating material is blocked
8
User’s guide OPUS cityLAM A3
Technical data:
Heating system:
Preheating time: Recommended pouch thickness: Max document thickness:
Laminating width:
Laminating Speed:
Power voltage:
Power:
Rated current:
Dimensions (WxDxH):
Net weight: * dokument wraz z folią laminacyjną
4 rollers
4 - 6 minutes
80 - 200mic
1 mm*
330 mm
360 / 420 mm/min (50/60 Hz)
AC 220 - 240 V / 50/60 Hz
460 W
2,0 A
470 x 150 x 105 mm
3,4 kg
14.11.2012
9