Download FDRMOVE FDRERASE - Innovation Data Processing

MESSAG ES AN D CODES
MESSAG ES
390.03
RACF FACILITY PROTECTION STGADMIN FAILED FOR resource
Reason: In this form of the FDR019 message, the operand STGADMIN was specified on a
MOVE or FASTMOVE statement for simplified storage administrator security
authorization in FDRMOVE. The user must be authorized to the RACF resource
STGADMIN.ADR.STGADMIN.MOVE
in class FACILITY or the equivalent in other security systems, but the security check
failed.
Action: A control card error is issued and the operation terminates. If the user cannot be
authorized to this resource, remove the STGADMIN operand so that normal FDR
security checking will be done (See “Security” on page 325-55).
FDR020
RACF VOLUME PROTECTION FAILED ON VOL=vvvvvv
Reason: Security checking was enabled in the FDR Global Options Table (the ALLCALL option).
A security call for class DASDVOL and volume “vvvvvv” failed. The user does not
have sufficient authority to perform this swap or erase.
Action: An U0801 ABEND is issued.
FDR021
RACF DATASET PROTECTION FAILED ON DSN=dsname
Reason: Security checking was enabled in the FDR Global Options Table (the ALLCALL option).
A security call for class DASDVOL and volume “vvvvvv” indicated that the volume was
not protected by DASDVOL, so FDRPAS began doing checks in class DATASET for
all data sets on the volume. The user does not have sufficient authority to the data set
named, so the FDRPAS operation was terminated.
Action: An U0801 ABEND is issued.
FDR023
DUMMY VTOC READ -- ENTIRE PACK WILL BE DUMPED
Reason: FDRPAS found that the VTOC on this volume started and ended on cylinder zero head
zero. This is the format used on volumes initialized by z/VM; that dummy VTOC is not
valid.
Action: FDRPAS will copy all tracks on the volume.
FDR024
INVALID EXTENT DESCRIPTOR [REASON=reason DSN=dsname]
Reason: FDR read a DSCB (Format 1 or 3) that contained an invalid extent description. If a
mini-dump is printed, the first five bytes of the DSCB printed after the registers in the
mini-dump are the cylinder, head, and record number (CCHHR) of the DSCB in error.
If REASON= is printed, it is one of the following:
1–
2–
3–
4–
NOTE:
ENDING CYLINDER TOO LARGE
STARTING TRACK TOO LARGE
ENDING CCHH BEFORE BEGIN
ENDING TRACK TOO LARGE
Reasons 2 and 4 indicate that the starting or ending track number of an extent is
higher than the highest track on a cylinder, i.e., higher than 14 on 3380 or 3390;
not that the start or end of an extent is after the end of the pack.
If you are swapping to a smaller disk, reason “1” probably means that a data set on
the source disk has extents beyond the end of the target disk. For a SWAPBUILDIX, it
may mean that the communication disk specified by SWAPUNIT= is smaller than the
disk whose VTOCIX is to be rebuilt.
Action: FDRPAS will terminate the swap. You must correct the VTOC error or delete the
identified data set before attempting to swap the volume again. If necessary, contact
INNOVATION DATA PROCESSING for assistance.
FDR032
NO VALID TAPE(X) DD (OR MOUNT) STATEMENTS WERE FOUND
Reason: FDRMOVE did not select any volumes to process from the supplied SELECT. This is
usually due to a misspelling of the volser(s) on the SELECT statement.
Action: Check the spelling of the volser(s) on the SELECT statement and resubmit.
- 390-8 -