Download User`s Manual
Transcript
● ● ● ● ● ● ● ● ● 850 !" ● 936#$%& ● ' ● '() ● ● PPS300XS Series ATTEN INSTRUMENTS RF Microwave Instruments ● RF Microwave Components Spectrum Analyzers ● Regulated DC Power Supply ● Regulated AC Power Supply ● Switching DC Power Supply ● Digital Storage Oscilloscope ● Signal Generator ● Attenuator ● 850 Rework Station ● 936 Constant Temp Soldering Station ● Electronic Instruments ● Electronic Tools PROGRAMMABLE DC POWER SUPPLY ● ● ● Amplifier PPS 3003S / PPS 3005S !"#$%$#& User’s Manual / FRANCHISER CBN 019139 : A29 MFR Add: Building A29, Tanglang Industrial Zone, Xili, Nanshan, Shenzhen, 518055, P. R. China ATTENTION Kindly use the rated input voltage; Never operate at a high temperature and the cooling exit mustn't be blocked; Please make the fuse with rated parameters equipped. 1.voltage display Displaying setted voltage or output voltage display 2.current display setted current display or output current display 3.Storage data instruction instructing storage data 4.Adjusting knob current and voltage adjusting knob 5.Key store storage-selected key 6. ↑ Selecting the next storage 7. ↓ Selecting the previous storage Voltage setting 8.V SET Current setting 9. I SET Switching on or off output voltage 10.Key OUTPUT 11.ON/OFF button 12. output port and grounding port 13. fan 14.AC input socket 15.Interface USB or RS232, depending on the exact requirements flickering, when the power is in the mode of over current protection; that is, the over current protection starts when the current is up to the setted value; Switch off the output voltage and the over current protection light [OCP] is on. Eliminating the mode of the over current protection: press the key [RECALL] and the storage direction will flicker. At this time, press [OUTPUT] and it will stop flickering, when the power supplies will exit from the over current protection mode. 4.Storage Selection: Press the key [STORE] and the storage direction light will flicker, which indicates the current storage data. Then press the key [↓] and the next parameters of voltage and current can be selected; press [↑] and the previous parameters can be selected. In any storage direction, the relevant storage units can be stored when the parameters of voltage and current are setted. 5.Switching on or off the output: Press the key [OUTPUT] and the output voltage will be switched on or off. OPERATING INSTRUCTIONS 1. Output Voltage Adjustment: Press the key [VSET] and then the value of voltage setting will be displayed on the voltage display; and the place setted flickers. Repress and the selected place of the setting values will be changed. And turn the knob and the setting value of the output voltage will be adjusted when the setted place flickers. Stop turning for a few seconds, then the setted place stops flickering and the power will return to the initial status. 2.Output Current Adjustment: Press the key [ISET] and then the value of voltage setting will be displayed on the voltage display; and the place setted flickers. Repress and the selected place of the setting values will be changed. And turn the knob and the setting value of the output voltage will be adjusted when the setted place flickers. Stop turning for a few seconds, then the setted place stops flickering and the power will return to the initial status. 3.Over current protection: Press the key [RECALL] and the storage direction will flicker. At this time, press [OUTPUT] and it will stop 5 KLM , , !"#$%。 `ÑÒÓ '() ● ● ● ● ● ● '()*+,-.0134。 5678:;<=>?01@BCD。 '(01EFG$,$。 '(H+IJKLMNOPQ。 .01RST$&U,'(01W$ >。 .XYTZ[\]^_`'abcd 01。 1 2 5 6 3 4 7 8 7 9 11 12 *+,● ● gh$%AC220V,50Hz(110Vq) $&stWHuSv56$8。 °ÑÒÓ ./ PPSy{ !$&|}~$& $& ,H, , = >,, u$&。 gP$% gP$# gP¡ PPS3003S 0~30V 0~3A 90W 13 PPS3005S 0~30V 0~5A 150W 14 15 0123 ¥¦~25 5 ℃¨©ª,«¬®¯°± ²³´。 1. $%ÔÕ 2. $#ÔÕ 3. Ö×Ø~³Õ 4. ÙÚÛÜ 5. STOREÝ 6. ↑ 7. ↓ 8. VSET 45: CV≤0.01%+3mV(AC 5%) 6745: CV≤0.5%+10mV 89;<=: ≤1.0mVrms >?@A: V:0.5%+2Lsb I:1%+5Lsb B#@A: V: 0.5%+10Lsb I:1%+20Lsb CDEF: ¿#,¿%,¿À GH: USBSQ(ÄÅÆ(ÇqÈ) IJ: 0-40℃,ÌÍÎ80% 2 9. ISET 10. OUTPUTÝ $&«æçÜ gPèQéSèQ 13. LM 14. ê#ghëì 15. USB:RS232SQ (í(Çî) 11. 12. 1. $%ÔÕ 2. $#ÔÕ 3. Ö×Ø~³Õ 4. ÙÚÛÜ 5. STOREÝ 6. ↑ 7. ↓ 8. VSET 9. ISET 10. OUTPUTÝ 11. $&«æçÜ 12. gPèQéSèQ 13. LM 14. ê#ghëì 15. USB:RS232SQ(í(Çî) ÔÕ0$%:gP$%ÔÕ ÔÕ0$#:gP$#ÔÕ ³ÕÖ×Ø~ $%$#ÙÚÛÜ ÙÖ×çÝ ÙªØÖ× Ù4ØÖ× $%0-Ý $#0-Ý «:ægP$% Read-back accuracy: V: 0.5%+10Lsb I: 1%+20Lsb Types of protection: over current, over voltage, over temperature Interface: USB (optional according to the requirements of the customers) Working environment: 0 ~ 40℃ Humidity: less than 80% Thanks a lot for choosing our products. Please kindly read this manual carefully before operation. INSTRUCTIONS ● ● ● ● ● ● Never put the heavy objects on this equipment; Never crash or damage the machine due to improper operation; Never make the equipment be static discharge; Don't block the cooling exit; Don't make the equipment power on when it is connected to the power; Never disassemble it unless getting the confirmation of the professionals. DIAGRAMS OF PANELS Front Panel WARNING 4、gh]:çª【STORE】Ý,Ö× ³Õüýþ,³Õ`Ö×Ø~,¥U çª【↓】Ý,ùÙPªØ$%$ #¦~,çª【↑】Ý,ùÙPª Ø$%$#¦~。.ØÖ×³Õ U0-$%$#¦~ùÖhtÖ× 。 WXYZ 1、>?\]^:çª【VSET】Ý,$ %ÔÕøQùÔÕ$%0-ú,û0üýþ,*ÿ窰,0-úq ü,0-üýþUÛÜùÙÚ gP$%0-ú。~°0üý,$&ÿ 。 5、ijklm>?:çª【OUTPUT】 Ýù«:ægP$%。 2、>?`]^:çª【ISET】Ý,$#Ô ÕøQùÔÕ$#0-ú,û0-üý þ,*ÿ窰,0-úqü ,0-üýþUÛÜùÙÚgP $#0-ú。~°0-ü ý,$&ÿ 。 nopq ● ● 3、a`CD*b:çª【RECALL】Ý, Ö׳Õýþ,¥Uçª【OUTPUT】 , Ö׳Õýþ,¥U$&Eh¿ #,ù$# T0úU¿ #,ægP$%,U¿# 【OCP】。 ● ïgh$%。 56¨©À¿,¬°NOð'ñò。 óï¦~ôõ Output voltage AC 220V, 50Hz (110V optional) ● The power cord must be with reliable grounding to avoid the electronic shock. ● 1 2 5 6 3 4 7 8 7 9 11 12 BRIEF INTRODUCTION OF THE PRODUCT PPS series single programmable power supplies, with high stability, low ripple, easy operation and complete protection functions, are combined with the advantages of digital power supplies and analog power supplies. Therefore, we can provide you handy, reliable and quality power supplies. Model Output voltage Output current Output power PPS3003S 0~30V 0~3A 90W Rear Panel 13 PPS3005S 0~30V 0~5A 150W TECHNICAL PARAMETERS These parameters are tested under 25 ± 5℃ and after 2s power on. Power effect: CV≤0.01%+3mV(AC±5%) CV≤0.5%+10mV Load effect: Ripple and noise: ≤1.0mVrms Output accuracy: V: 0.5%+2Lsb I: 1%+5Lsb cda`CDef:çª【RECALL】 Ý,Ö׳Õýþ,¥Uçª 【OUTPUT】, Ö׳Õýþ,¥ U$&P¿#。 3 15 4 14