Download SERVICE MANUAL

CDX-GT34W/GT340
SERVICE MANUAL
US Model
CDX-GT34W/GT340
Canadian Model
Ver. 1.0 2009.07
CDX-GT34W
Photo: CDX-GT34W
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
CDX-GT23W/GT24/GT24EE
CD Drive Mechanism Type
MG-101L-188//Q
Optical Pick-up Name
DAX-25A
SPECIFICATIONS
CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and flutter: Below measurable limit
Power amplifier section
Output: Speaker outputs (sure seal connectors)
Speaker impedance: 4 – 8 ohms
Maximum power output: 52 W × 4 (at 4 ohms)
Tuner section
FM
Tuning range: 87.5 – 107.9 MHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
General
Outputs:
Audio outputs terminal (Front, sub/rear
switchable)
Power antenna (aerial) relay control terminal
Power amplifier control terminal
Inputs:
Bus control input terminal
Bus audio input terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
AM
Tuning range: 530 – 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26 μV
Dimensions: Approx. 178 × 50 × 179 mm
(7 1/8 × 2 × 7 1/8 in) (w/h/d)
Mounting dimensions:
Approx. 182 × 53 × 162 mm
(7 1/4 × 2 1/8 × 6 1/2 in) (w/h/d)
Mass: Approx. 1.2 kg (2 lb 11 oz)
Supplied accessories:
Card remote commander: RM-X151
Parts for installation and connections (1 set)
Design and specifications are subject to change
without notice.
FM/AM COMPACT DISC PLAYER
9-889-584-01
Sony Corporation
2009G04-1
© 2009.07
Audio&Video Business Group
Published by Sony Techno Create Corporation
CDX-GT34W/GT340
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
optical pick-up
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
TEST DISCS
Please use the following test discs for the check on the CD section.
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
semi-fixed resistor
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
CDX-GT34W/GT340
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
TABLE OF CONTENTS
1.
SERVICING NOTES .............................................
2.
GENERAL
Connections ....................................................................
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
3-11.
Sub Panel Assy................................................................
CD Mechanism Block .....................................................
Main Board .....................................................................
Servo Board ....................................................................
Chassis (T) Sub Assy ......................................................
Roller Arm Assy..............................................................
Chassis (OP) Assy ...........................................................
Chucking Arm Sub Assy .................................................
Sled Motor Assy..............................................................
Optical Pick-up Section ..................................................
Optical Pick-up ...............................................................
4.
DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
Block Diagram –Main Section– .....................................
Block Diagram –Display Section– .................................
Printed Wiring Board –Main Section–............................
Schematic Diagram –Main Section (1/3)–......................
Schematic Diagram –Main Section (2/3)–......................
Schematic Diagram –Main Section (3/3)–......................
Printed Wiring Board –Key Section– .............................
Schematic Diagram –Key Section – ...............................
5.
EXPLODED VIEWS
4
5
8
8
9
9
10
10
11
11
12
13
13
15
16
17
18
19
20
21
22
5-1. Main Section ................................................................... 28
5-2. Front Panel Section ......................................................... 29
5-3. CD Mechanism Section (MG-101L-188//Q) .................. 30
6.
ELECTRICAL PARTS LIST .............................. 31
3
CDX-GT34W/GT340
SECTION 1
SERVICING NOTES
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension
cable) as shown below.
•
Connect the MAIN board (CNP301) and the SERVO board
(CN401) with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CNP301
J-2502-076-1
SERVO BOARD
CN401
NOTE FOR REPLACEMENT OF THE AUX JACK (J901)
To replace the AUX jack requires alignment.
1. Insert the AUX jack into the KEY board.
2. Place the KEY board on the front panel.
3. Solder the three terminals of the jack.
KEY board
AUX jack
front panel
4
NOTE FOR REPLACEMENT OF THE SERVO BOARD
When repairing, the complete SERVO board (Part No. A-1552122-A) should be replaced since any parts in the SERVO board
cannot be repaired.
NOTE FOR THE 15-PIN CONNECTOR (CN901)
Do not use alcohol to clean the 15-pin connector (CN901) connecting the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor contact may be caused.
CDX-GT34W/GT340
SECTION 2
GENERAL
This section is extracted
from instruction manual.
CONNECTIONS
• CDX-GT34W
CDX-GT34W
*1
*2
Source selector
(not supplied)
Sélecteur de source
(non fourni)
Selector de fuente
(no suministrado)
Supplied with XA-C40
Fourni avec le XA-C40
Suministrado con el XA-C40
*2
Supplied with the CD changer
Fourni avec le changeur de CD
Suministrado con el cambiador de CD
XA-C40
FRONT
AUDIO OUT*1
CDX-GT34W
BUS AUDIO IN*1
*1 CDX-GT34W only
*2 RCA pin cord (not supplied)
*3 AUDIO OUT can be switched SUB or
REAR. For details, see the supplied
Operating Instructions.
L
R
from car antenna (aerial)
à partir de l’antenne du véhicule
desde la antena del automóvil
BUS REAR/SUB FRONT
IN
AUDIO OUT
REAR / SUB
Fuse (10 A)
AUDIO OUT*3 Fusible (10 A)
Fusible (10 A)
3
*1 CDX-GT34W uniquement
*2 Cordon à broche RCA (non fourni)
*3 AUDIO OUT peut être commuté sur SUB
ou REAR. Pour obtenir plus de détails,
reportez-vous au mode d’emploi fourni.
BUS
CONTROL IN*1
2
Blue/white striped
Rayé bleu/blanc
Con rayas azules y blancas
*1 Solo CDX-GT34W
*2 Cable con terminales RCA (no
suministrado)
*3 AUDIO OUT (salida de audio) puede
cambiarse a SUB o REAR. Para obtener
información, consulte el manual de
instrucciones suministrado.
AMP REM
Max. supply current 0.3 A
Courant max. fourni 0,3 A
Corriente máx. de alimentación de 0,3 A
Left
Gauche
Izquierdo
White
Blanc
Blanco
White/black striped
Rayé blanc/noir
Con rayas blancas y negras
Black
Noir
Negro
Right
Droit
Derecho
Gray
Gris
Gris
Gray/black striped
Rayé gris/noir
Con rayas grises y negras
Blue
Bleu
Azul
Left
Gauche
Izquierdo
Green
Vert
Verde
Green/black striped
Rayé vert/noir
Con rayas verdes y negras
Red
Rouge
Rojo
Right
Droit
Derecho
Purple
Violet
Morado
Purple/black striped
Rayé violet/noir
Con rayas moradas y negras
Yellow
Jaune
Amarillo
Connection diagram
Schéma de raccordement
1
ANT REM
Max. supply current 0.1 A
Courant max. fourni 0,1 A
Corriente máx. de alimentación de 0,1 A
4
5
Diagrama de conexión
1 To a metal surface of the car
1 À un point métallique de la voiture
1 $XQDVXSHU¿FLHPHWiOLFDGHODXWRPyYLO
2 To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
2 Au câble de commande d’antenne électrique
ou au câbOHG¶DOLPHQWDWLRQGHO¶DPSOL¿FDWHXU
d’antenne
2 Al cable de control de la antena motorizada
o al cabOHGHIXHQWHGHDOLPHQWDFLyQGHO
DPSOL¿FDGRUGHVHxDOGHODDQWHQD
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
Notes
‡ It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
‡ When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
3 To AMP REMOTE IN of an optional power
DPSOL¿HU
This connection is only fRUDPSOL¿HUs. Connecting any other
system may damage the unit.
4 To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
‡ If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surfDFHRIWKHFDU¿UVW
‡ When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
5 To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surfDFHRIWKHFDU¿UVW
Notes on the control and power supply leads
‡ The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
‡ When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
‡ A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
‡ Before connecting the speakers, turn the unit off.
‡ Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
‡ Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
‡ Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
‡ Do not attempt to connect the speakers in parallel.
‡ Connect only passive speakers. Connecting active speakers
(with bXLOWLQDPSOL¿HUVWRWKHVSHDker terminals may damage
the unit.
‡ To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
‡ Do not connect the unit’s speaker leads to each other.
Note on connection
If speakHUDQGDPSOL¿HUDUHQRWFRQQHFWHGFRUUHFWOy, “FAILURE”
appears in the display. In this case, make sure the speaker and
DPSOL¿HUDUHFRQQHFWHGFRUUHFWOy.
Branchez d’abord le câble de mise à la masse noir et,
ensuite, les câbles d’alimentation jaune et rouge.
Remarques
‡ Il n’est pas nécessaire de raccorder ce câble s’il n’y a pas
d’antenne électrLTXHQLG¶DPSOL¿FDWHXUG¶DQWHQQe, ou avec
une antenne télescopique manuelle.
‡ Si votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, voir « Remarques
sur les câbles de commande et d’alimentation ».
3 Au niveau de AMP REMOTE IN de
O¶DPSOL¿FDWHXUGHSXLVVDQFHHQRSWLRQ
Ce rDFFRUGHPHQWV¶DSSOLTXHXQLTXHPHQWDX[DPSOL¿FDWHXUs.
Le branchement de tout autre système risque
d’endommager l’appareil.
4 À la borne d’alimentation +12 V qui est
alimentée quand la clé de contact est sur la
position accessoires
Remarques
‡ S’il n’y a pas de position accessoires, raccordez la borne
d’alimentation (batterie) +12 V qui est alimentée en
permanence.
Raccordez d’abord le câble de mise à la masse noir à un
point métallique du véhicule.
‡ Si votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, voir « Remarques
sur les câbles de commande et d’alimentation ».
5 À la borne d’alimentation +12 V qui est
alimentée en permanence
Raccordez d’abord le câble de mise à la masse noir à un
point métallique du véhicule.
Remarques sur les câbles de commande et d’alimentation
‡ Le câble de commande d’antenne électrique (bleu) fournit une
alimentation de + 12 V CC lorsque vous mettez la radio sous
tension.
‡ Lorsque votre voiture est équipée d’une antenne FM/
AM intégrée dans la vitre arrière/latérale, raccordez le
câble de commande d’antenne électrique (bleu) ou le
câble d’alimentation des accessoires (rouge) à la borne
G¶DOLPHQWDWLRQGHO¶DPSOL¿FDWHXUG¶DQWHQQHexistant. Pour plus
de détails, consultez votre détaillant.
‡ Une antenne électrique sans boîtier de relais ne peut pas être
utilisée avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le câble d’alimentation jaune est raccordé, le circuit
de la mémoire est alimenté en permanence même si la clé de
contact est sur la position d’arrêt.
Remarques sur le raccordement des haut-parleurs
‡ Avant de raccorder les haut-parleurs, mettez l’appareil hors
tension.
‡ Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms
avec une capacité électrique adéquate pour éviter de les
endommager.
‡ Ne raccordez pas les bornes du système de haut-parleurs au
châssis de la voiture et ne raccordez pas les bornes du hautparleur droit à celles du haut-parleur gauche.
‡ Ne raccordez pas le câble de mise à la masse de cet appareil
à la borne négative (–) du haut-parleur.
‡ N’essayez pas de raccorder les haut-parleurs en parallèle.
‡ Raccordez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avHFDPSOL¿FDWHXUVLQWpgrés)
aux bornes des haut-parleurs peut endommager l’appareil.
‡ Pour éviter tout problème de fonctionnement, n’utilisez pas les
câbles des haut-parleurs intégrés installés dans votre voiture si
l’appareil possède un câble négatif commun (–) pour les hautparleurs droit et gauche.
‡ Ne raccordez pas entre eux les cordons des haut-parleurs de
l’appareil.
Remarque sur le raccordement
Si le haut-parOHXUHWO¶DPSOL¿FDWHXUQHVRQWSDVraccordés
correctement, le message « F$,/85(ªV¶DI¿FKe. Dans ce cas,
assurez-vous que les haut-parOHXUVHWO¶DPSOL¿FDWHXUVRQWELHQ
raccordés.
2
Conecte primero el cable de conexión a masa negro, y
después los cables amarillo y rojo de fuente de alimentación.
Notas
‡ Si no se dispone de antena motorL]DGDQLGHDPSOL¿FDGRU
de antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
‡ Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
3 A AMP REMO7(,1GHXQDPSOL¿FDGRUGH
potencia opcional
Esta conexión es sólo parDDPSOL¿FDGRUHs. La conexión de
cualquier otro sistema puede dañar la unidad.
4 $OWHUPLQDOGHDOLPHQWDFLyQGH V que
recibe enerJtDHQODSRVLFLyQGHDFFHVRULR
del interruptor de encendido
Notas
‡ Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a
masa negURDXQDVXSHU¿FLHPHWiOLFDGHODXWRPóvil.
‡ Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
5 $OWHUPLQDOGHDOLPHQWDFLyQGH V que
recibe enerJtDVLQLQWHUUXSFLyQ
Asegúrese de conectar primero el cable de conexión a masa
negURDXQDVXSHU¿FLHPHWiOLFDGHODXWRPóvil.
Notas sobre los cables de control y de fuente de
alimentación
‡ El cable de control de la antena motorizada (azul) suministrará
cc de +12 V cuando conecte la alimentación del sintonizador.
‡ Si el automóvil dispone de una antena de FM/AM incorporada
en el cristal trasero o lateral, conecte el cable de control de
antena motorizada (azul) o el cable de fuente de alimentación
auxiliar (rojo) al terPLQDOGHDOLPHQWDFLyQGHODPSOL¿FDGRUGH
antena existente. Para obtener más información, consulte a su
distribuidor.
‡ Con esta unidad no es posible utilizar una antena motorizada
sin caja de relé.
Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Notas sobre la conexión de los altavoces
‡ Antes de conectar los altavoces, desconecte la alimentación
de la unidad.
‡ Utilice altavoces con una impedancia de 4 a 8 : con la
capacidad de potencia adecuada para evitar que se dañen.
‡ No conecte los terminales de altavoz al chasis del automóvil,
ni conecte los terminales del altavoz derecho con los del
izquierdo.
‡ No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
‡ No intente conectar los altavoces en paralelo.
‡ Conecte solamente altavoces pasivos. Si conecta altavoces
activRVFRQDPSOL¿FDGRUHVLQFRrporados) a los terminales de
altavoz, puede dañar la unidad.
‡ Para evitar fallas de funcionamiento, no utilice los cables de
altavoz incorporados instalados en el automóvil si la unidad
comparte un cable negativo común (–) para los altavoces
derecho e izquierdo.
‡ No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavR]\HODPSOL¿FDGRUQRHVWiQFRQHFWDGRV
correctamente, aparecerá “FAILURE” en la pantalla. Si es así,
compruebe la conexión de ambos dispositivos.
5
CDX-GT34W/GT340
• CDX-GT340
CDX-GT340
*1
*2
Source selector
(not supplied)
Sélecteur de source
(non fourni)
Supplied with the CD changer
Fourni avec le changeur de CD
XA-C40
Supplied with XA-C40
Fourni avec le XA-C40
*2
FRONT
AUDIO OUT*1
CDX-GT340
BUS AUDIO IN*1
*1 CDX-GT340 only
*2 RCA pin cord (not supplied)
*3 AUDIO OUT can be switched SUB or
REAR. For details, see the supplied
Operating Instructions.
L
R
from car antenna (aerial)
à partir de l’antenne du véhicule
BUS REAR/SUB FRONT
IN
AUDIO OUT
REAR / SUB
Fuse (10 A)
AUDIO OUT*3 Fusible (10 A)
Blue/white striped
Rayé bleu/blanc
3
*1 CDX-GT340 uniquement
*2 Cordon à broche RCA (non fourni)
*3 AUDIO OUT peut être commuté sur SUB
ou REAR. Pour obtenir plus de détails,
reportez-vous au mode d’emploi fourni.
BUS
CONTROL IN*1
2
AMP REM
Max. supply current 0.3 A
Courant max. fourni 0,3 A
Left
Gauche
White
Blanc
Black
Noir
1
White/black striped
Rayé blanc/noir
Right
Droit
Gray
Gris
Blue
Bleu
ANT REM
Max. supply current 0.1 A
Courant max. fourni 0,1 A
Gray/black striped
Rayé gris/noir
Left
Gauche
Green
Vert
Red
Rouge
4
Green/black striped
Rayé vert/noir
Right
Droit
Purple
Violet
Yellow
Jaune
Purple/black striped
Rayé violet/noir
Connection diagram
Schéma de raccordement
1 TRDPHWDOVXUIDFHRIWKHFDU
1 À un point métallique de la voiture
2 TRWKHSower antenna (aerial) control lead or
poZHUVXSSl\OHDGRIDQWHQQDDHULDOERRVWHU
2 Au câble de commande d’antenne électrique
ou au câbOHG¶DOLPHQWDWLRQGHO¶DPSOL¿FDWHXU
d’antenne
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
Notes
‡ It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
‡ When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
3 To AMP REMO7(,1RIDQRSWLRQDOSower
DPSOL¿HU
This connection is only fRUDPSOL¿HUs. Connecting any other
system may damage the unit.
4 TRWKH V poZHUWHUPLQDOZKLcKLV
energizHGLQWKHDFFHVVRr\SRVLWLRQRIWKH
ignition VwitcK
Notes
‡ If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surfDFHRIWKHFDU¿UVW
‡ When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
5 TRWKH V poZHUWHUPLQDOZKLcKLV
energizHGDWDOOWLPHV
Be sure to connect the black ground (earth) lead to a metal
surfDFHRIWKHFDU¿UVW
Notes on the control and power supply leads
‡ The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
‡ When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
‡ A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
‡ Before connecting the speakers, turn the unit off.
‡ Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
‡ Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
‡ Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
‡ Do not attempt to connect the speakers in parallel.
‡ Connect only passive speakers. Connecting active speakers
(with bXLOWLQDPSOL¿HUVWRWKHVSHDker terminals may damage
the unit.
‡ To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
‡ Do not connect the unit’s speaker leads to each other.
Note on connection
If speakHUDQGDPSOL¿HUDUHQRWFRQQHFWHGFRUUHFWOy, “FAILURE”
appears in the display. In this case, make sure the speaker and
DPSOL¿HUDUHFRQQHFWHGFRUUHFWOy.
6
2
Branchez d’abord le câble de mise à la masse noir et, ensuite, les
câbles d’alimentation jaune et rouge.
Remarques
‡ Il n’est pas nécessaire de raccorder ce câble s’il n’y a pas
d’antenne électrLTXHQLG¶DPSOL¿FDWHXUG¶DQWHQQe, ou avec une
antenne télescopique manuelle.
‡ Si votre voiture est équipée d’une antenne FM/AM intégrée
dans la vitre arrière/latérale, voir « Remarques sur les câbles de
commande et d’alimentation ».
3 Au niveau de AMP REMOTE IN de
O¶DPSOL¿FDWHXUGHSXLVVDQFHHQRSWLRQ
Ce rDFFRUGHPHQWV¶DSSOLTXHXQLTXHPHQWDX[DPSOL¿FDWHXUs.
Le branchement de tout autre système risque d’endommager
l’appareil.
4 À la borne d’alimentation +12 9TXLHVW
alimentée quand la cOpGHFRQWDFWHVWVXUOD
SRVLWLRQDFFHVVRLUHV
Remarques
‡ S’il n’y a pas de position accessoires, raccordez la borne
d’alimentation (batterie) +12 V qui est alimentée en permanence.
Raccordez d’abord le câble de mise à la masse noir à un point
métallique du véhicule.
‡ Si votre voiture est équipée d’une antenne FM/AM intégrée
dans la vitre arrière/latérale, voir « Remarques sur les câbles de
commande et d’alimentation ».
5 À la borne d’alimentation +12 9TXLHVW
alimentée en permanence
Raccordez d’abord le câble de mise à la masse noir à un
point métallique du véhicule.
Remarques sur les câbles de commande et d’alimentation
‡ Le câble de commande d’antenne électrique (bleu) fournit une
alimentation de + 12 V CC lorsque vous mettez la radio sous tension.
‡ Lorsque votre voiture est équipée d’une antenne FM/AM intégrée
dans la vitre arrière/latérale, raccordez le câble de commande
d’antenne électrique (bleu) ou le câble d’alimentation des accessoires
(rouge) à la borQHG¶DOLPHQWDWLRQGHO¶DPSOL¿FDWHXUG¶DQWHQQHexistant.
Pour plus de détails, consultez votre détaillant.
‡ Une antenne électrique sans boîtier de relais ne peut pas être utilisée
avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le câble d’alimentation jaune est raccordé, le circuit de la
mémoire est alimenté en permanence même si la clé de contact est sur
la position d’arrêt.
Remarques sur le raccordement des haut-parleurs
‡ Avant de raccorder les haut-parleurs, mettez l’appareil hors tension.
‡ Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec
une capacité électrique adéquate pour éviter de les endommager.
‡ Ne raccordez pas les bornes du système de haut-parleurs au châssis
de la voiture et ne raccordez pas les bornes du haut-parleur droit à
celles du haut-parleur gauche.
‡ Ne raccordez pas le câble de mise à la masse de cet appareil à la
borne négative (–) du haut-parleur.
‡ N’essayez pas de raccorder les haut-parleurs en parallèle.
‡ Raccordez uniquement des haut-parleurs passifs. Le raccordement
de haut-parleurs actifs (avHFDPSOL¿FDWHXUVLQWpgrés) aux bornes des
haut-parleurs peut endommager l’appareil.
‡ Pour éviter tout problème de fonctionnement, n’utilisez pas les câbles
des haut-parleurs intégrés installés dans votre voiture si l’appareil
possède un câble négatif commun (–) pour les haut-parleurs droit et
gauche.
‡ Ne raccordez pas entre eux les cordons des haut-parleurs de
l’appareil.
Remarque sur le raccordement
Si le haut-parOHXUHWO¶DPSOL¿FDWHXUQHVRQWSDVraccordés
correctement, le message « F$,/85(ªV¶DI¿FKe. Dans ce cas,
assurez-vous que les haut-parOHXUVHWO¶DPSOL¿FDWHXUVRQWELHQ
raccordés.
5
CDX-GT34W/GT340
SECTION 3
DISASSEMBLY
•
This set can be disassembled in the order shown below.
SET
3-1.
SUB PANEL ASSY
(Page 8)
3-2.
CD MECHANISM BLOCK
(Page 8)
3-3.
MAIN BOARD
(Page 9)
3-4.
SERVO BOARD
(Page 9)
3-5.
CHASSIS (T) SUB ASSY
(Page 10)
3-6.
ROLLER ARM ASSY
(Page 10)
3-7.
CHASSIS (OP) ASSY
(Page 11)
3-8.
CHUCKING ARM SUB ASSY
(Page 11)
3-9.
SLED MOTOR ASSY
(Page 12)
3-10. OPTICAL PICK-UP SECTION
(Page 13)
3-11. OPTICAL PICK-UP
(Page 13)
7
CDX-GT34W/GT340
Note: Follow the disassembly procedure in the numerical order given.
3-1.
SUB PANEL ASSY
3 two claws
2 two claws
1 two screws
(+PTT 2.6 u 6)
4 sub panel assy
3-2.
CD MECHANISM BLOCK
7 CD mechanism block
6 bracket (CD)
5 two screws
(+PTT 2.6 u 4)
3
2 screw
(+PTT 2.6 u 6)
4 CNP301
1 screw
(+PTT 2.6 u 6)
8
CDX-GT34W/GT340
3-3.
MAIN BOARD
2 two screws
(+PTT 2.6 u 8)
4 screw
(+PTT 2.6 u 10)
5 two screws
(+P 2.6 u 8)
6 two screws
(+PTT 2.6 u 10)
7 two screws
(+P 2.6 u 8)
1 three screws
(+BTT 2.6 u 5)
8 screw
(+PTT 2.6 u 10)
9 heat sink
0 MAIN board
3
3-4.
insulating sheet
SERVO BOARD
white
red
black
white
red
black
red
orange
blue
yellow
gray
2 toothed lock screw
(M 1.7 u 2.5)
3 toothed lock screw
(M 1.7 u 2.5)
SERVO board
1 Remove the eleven solders.
5 claw
7 SERVO board
6 optical pick-up (16 core)
(CN101)
4 claw
9
CDX-GT34W/GT340
3-5.
CHASSIS (T) SUB ASSY
2 two screws
(M 1.7 u 2.5)
1 two screws
(M 1.7 u 2.5)
4 chassis (T) sub assy
3 claw
3-6.
ROLLER ARM ASSY
6 roller arm assy
5
1 spring (RAL)
4 gear (RA1)
3 washer
2 spring (RAR)
10
CDX-GT34W/GT340
3-7.
CHASSIS (OP) ASSY
6 chassis (OP) assy
1 tension spring (KF)
5
7 two coil springs (damper) (natural)
8 coil spring (damper) (green)
4 slider (R)
3 lever (D)
2 gear (LE1)
3-8.
CHUCKING ARM SUB ASSY
3 chucking arm sub assy
1 spring
2
Note: Have this portion receive the chassis.
Note: Have this portion receive the chassis.
Note: Be careful not to touch the turn table.
11
CDX-GT34W/GT340
3-9.
SLED MOTOR ASSY
2 three serration screws
(M 2 u 3)
3 sled motor assy
1 spring
turn table
spring
stand
Note:
Never remove these parts since they were adjusted.
bearing (F)
stand
Note: Place the stand with care not to touch the turn table.
bearing (R)
Note for Assembly
three serration screws
(M 2 u 3)
sled motor assy
Note: Take care to prevent the chassis from being bent
when tightening the three machine screws.
12
CDX-GT34W/GT340
3-10. OPTICAL PICK-UP SECTION
2 optical pick-up section
1
Note: Be careful not to touch the lens and hologram
terminal when removing the optical pick-up section.
3-11. OPTICAL PICK-UP
1 tapping screw
(P 1.4)
2 leaf spring (OPS)
3 rack
5 optical pick-up
4 lead screw assy
13
CDX-GT34W/GT340
MEMO
14
CDX-GT34W/GT340
SECTION 4
DIAGRAMS
4-1.
BLOCK DIAGRAM – MAIN Section –
ELECTRONIC VOLUME
IC401
J330
(1/2)
BUS
AUDIO
IN
L
R-CH
R-CH
L
SUB-L 30
SUB-R 31
2 BUS-L
R
J330
(2/2)
1 BUS-R
R-CH
R-CH
R
L
MUTE
Q481
R-CH
J901
AUX
R-CH
9 AUX-L
7 AUX-R
8 AUX-G
L6
FM MIX
J1
(ANTENNA)
4 FMIN1
3 FMIN2
LOUT 8
ROUT 9
R-CH
L2
R-CH
R-CH
1 AMRFIN
SCL 18
SDA 19
15 XTAL2
11 IN-RL
SCL 37
SDA 38
RSSI 14
UNI_SO
UNI_SI
UNI_CLK
Z_MUTE
CD_ON
CDM_ON
6
21
27
25
SYS_RST
EJECT_OK
BUS_ON
BUS_IN
28
LINK_OFF
9
A_ATT
18
19
8
1,2
D_+3.3V
A_+3.3V
BU_+3.3V
DR_+6V
14
A_8.5V
D512
12
43
44
19
RESET
SYSRST
BUSON
BUIN
BATT
BU+B
AUDIO+B
SERVO+3.3V
MECHA+6V
PANEL+B
16 BEEP
22 STB
25 DIAG
BUS INTERFACE
IC580
UNI SI
8
9
10
11
12
13
UNI SO
BU IN
UNISCK
BUS ON
SYSRST
DATA OUT
DATA IN
B/U-C
CLK IN
BUS IN
RST
BATT 3
BU_+3.3V
MECHA +6V
AUDIO +8.5V
VDD 2
OVER VOLTAGE
CHECK
Q580,D580,D581
BU+3.3V REG
IC681
1
2
3
8
‡ R-CH LV RPLWWHG GXH WR VDPH DV L-CH.
‡ SLJQDO PDWK
: CD PLAY
: AM
: AUX
: BUS AUDIO
CDX-GT34W/GT340
15
15
7
BATT
CN580
7
4
5
6
: FM
LINK OFF
B.U +5V
ANT-REM
BATT
SERVO+3.3V
MECHA+6V
PANEL+B
TH580
BUS ON/OFF
SWITCH
Q586
16
AMP-REM
B.U+5V
AUDIO +8.5V
BATT
CLK 4
DATA I/O 6
LINK ON/OFF
SWITCH
Q587
BU +3.3V
S702
RESET
BU+3.3V
37
30
31
33
34
RST 2
RESET
IC602
1 VOUT
FU601
ACCESSORY CHECK
Q631
ACC IN 55
BUS ON 1
SERVO +3.3V
6
ANT-REM 27
4 SCL
2 SDA
D511
D510
BU+3.3V
5
VP 35
VP1 20
VP2 6
I2C-SCL
I2C-SDA
FRONT
4
FR+
12
FR–
3
RR+
11
RR–
AMP-REM 29
ATT 56
UNISO
UNISI
UNISCK
Z-MUTE
CD_ON
CDM_ON
2
RL+
10
RL–
BATT
BEEP 28
AMPSTB 58
DIAG 57
R-CH
5
6
7
21
52
20
OUT-RL+ 9
OUT-RL– 7
R-CH
I2C-SCL
I2C-SDA
UNISI
UNISCK
SYSRST
BUSON
BUIN
22
24
26
16
5
7
AU_RCH
1
FL+
9
FL–
D479
SAIN 83
SADATD 89
SACLK 90
93 VSM
UNISO
AU_LCH
MUTE
CONTROL SWITCH
Q478,479
SYSTEM CONTROL
IC501 (1/2)
I2C_SCK 29
I2C_SIO 30
11
15
I2C-SCL
I2C-SDA
MUTE
Q461
OUT-FL+ 5
OUT-FL– 3
R-CH
6 CD-L
5 CD-R
I2C-SCL
I2C-SDA
MUTE
Q441
AUDIO
OUT
CN601
R-CH (FRONT)
R-CH (REAR)
SACLK 27
SADA 28
SAOUT 29
CNP301
CD
MECHANISM
UNIT
(MG-101L)
OUT-RL 32
4 TU-L
3 TU-R
16 XTAL1
X1
4MHz
12 IN-FL
OUT-FR 35
OUT-RR 33
ADVANCED TUNER/
RDS DECODER/PLL
IC1
I2C BUS CONTROLLED POWER AMP
/MULTIPLE VOLTAGE REGULATOR
IC750
OUT-FL 34
R
R-CH
REAR/SUB
BUS
CONTROL
IN
ACC
CDX-GT34W/GT340
4-2.
BLOCK DIAGRAM – DISPLAY Section –
SYSTEM CONTROL
IC501 (2/2)
94 KEYIN1
KEY MATRIX
LSW902–908,
S901–907
95 KEYIN0
LCD_SO 1
LCD_CKO 2
LCD_CE 100
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
LCD DRIVE
IC901
60
‡
S1 55
I
‡
S48 50
I
5
64 DATA
63 CLK
62 CE
ROTARY
ENCODER
DIMMER
S909
PUSH SELECT
(VOLUME)
BACK LIGHT
92 KEYACK1
1
2
LCD901
LIQUID
CRYSTAL
DISPLAY
PANEL
COM1 54
|
I
COM4 51
For Printed Wiring Boards.
For Schematic Diagrams.
Note:
• X : Parts extracted from the component side.
•
a : Through hole.
•
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
Note:
• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f : Internal component.
• C : Panel designation.
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
PANEL+B
• Indication of transistor.
RE-0
RE-1
82 RE-IN0
81 RE-IN1
(
LED931
LCD BACK
LIGHT
)
LED940,944–952,
955,956,960,961,
LSW902–908
KEY
ILLUMINATE
(
C
Q
)
These are omitted.
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
): AM
<
> : CD PLAY
• Voltages are taken with VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J
: CD PLAY
F
: FM
f
: AM
L : AUX
g : BUS AUDIO
B E
DIMMER
SWITCH
Q931
LCD
BACK LIGHT
SWITCH
Q932
REMOTE
CONTROL
SIGNAL
RECEIVER
IC902
4 SIRCS
X502
32.768kHz
X501
11.06MHz
10 XIN
• Waveforms
11 XOUT
– MAIN Board –
15 OSCIN
1
13 OSCOUT
3
IC1 qh (XTAL1)
IC501 qd (OSCOUT)
3 NOSE_SW
40 mVp-p
4 MHz
2
1 V/DIV, 50 nsec/DIV
IC501 qa (XOUT)
1.7 Vp-p
32.768 kHz
0.5 V/DIV, 10 Psec/DIV
CDX-GT34W/GT340
16
16
3.4 Vp-p
11.06 MHz
20 mV/DIV, 100 nsec/DIV
Note:
Les composants identifiés
par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par
une pièce portant le numéro spécifié.
CDX-GT34W/GT340
4-3.
PRINTED WIRING BOARD – MAIN Section –
2
1
3
•
: Uses unleaded solder.
4
5
6
7
8
9
10
J330
AUDIO OUT
REAR/SUB
C504
JW40
R500
C551
R570
JW4
C601
R514
R532
JW41
JW140
C305
C306
JW28
JW62
JW27
JW115
JW109
JC302
JW111
JC303
JW23
JW153
R679
R584
R674
R517
R567
R516
R565
CN351
CD MECHANISM
UNIT
(MG-101L)
JW150
R508
R509
X501
R542
R553
R519 D502 JC501
R558
JW152
JW50
JW175
C509
R601
IC602
R543
JW55
C508
JC502
R533
31
1-877-021-
S702
CN701
X501
R676
R672
JW176
JW75
FMB4
JW167
C503
R501
C507
X502
JW174
R675
1
50
IC
C513
R511
R510
R512
R673
JW145
D510
S702
RESET
A
KEY BOARD CN901
(Page 21)
CDX-GT34W/GT340
R547
JW36
JW141
JW105
JW104
I
C709
FB308
R528
JW65
C519
C719
FB312
FB604
JW48
C707
C512
C514
JW37
C708
C501
R504 R502
R505 R503
R671
C510
JW74
C705
JW139
Q587
JW119
JW57
R561
C523
C522
JW133
R664
D719 R513
(CHASSIS)
R662 R661
JW79
C706
R677
R521
R522
JW68
D704
JW120
JW82
R507
L151 R152
D703
JW142
R591
JW49
R526
JW71
JC151
JW78
R555
R554
R578
R663
JW80
D153
JW61
R506
JW76
C155
C157
R154
C152
C154
JW144
R155
R580
R581
FB309
C312
JC580
Q586
R691
JW149
C151
C153
R153
D512
TH580
JW46
R590
1
IC580
R531
R534
JW33
R575
R551
R538
D584
JW47
R566
R151
7
JW59
JW146
R523
G
JW118
JW154
JW66
JW85
R530
JW77
R563
R582
D580
D581
Q580
R636
JW45
JW73
JW89
JW135
JW54
JW124
JW56
JW103
D511
JW84
JW94
C18
R13
R14
JC401
JC402
JW90
FMB3
JW113
JW134
JC521
C520
C580
FB311
R583
D583
D582
14
C343
C310 R302
C309 R301
C521
C28
R588
R587
JC301
C301
C308
JW99
R529
R756
JW51
L1
C302
JW106
JW156
R692
H
JW21
JW5
JW155
C27
JW102
C681
C479
R556
IC681
C683
C406
R631
JW136
R635
JW178
Q631
JW39
CNP301
FB304
R539
R12
D754
R681
JW151
JW147
JW130
C582
JW157
Q478
C682
C684
JW132
D479
C756 R479
L601
JW31
8
JW30
C26
D601
JC581
JW26
JW20
Q479
JW96
R633
JW97
JW129
C602
JW100
R634
JW108
JW148
C632
JW29
IC1
D753
D755
JW11
C752
JW93
JW91
D761
R632
C770
JW95
R11
C22
C23
C25
D762
C631
C776
R752
C755 JW98
D760
D759
JW25
C451
JW8
JW86
C17
C761
C412 C413 JW92
IC401
C581
C618
C750
C757
C13
C9
C21
C24
X1
JW126
JW38
JW88
C403
FB401
C409 FB402
C20
C769
JW18
C461
JW131
L7
JW200
C617
D617
JW7
C623
R461
C405
C404
L8
C19
R10
R6
R462
Q461
C431
JC497
JW2
JW3
D756
C408
C5
C12
R4
R5
C16
JW15
JW35
C401
E
JW14
JW42
C471
R333
C402
L6
C8
F
JC499
R3
R451
CN580
FU601
JW6
C465 R452
C455
C481
R330
R331
R332
C6
C1
FB2
FB1
D
L2
C763
C452 Q451
C462
C441
R481
CN601
C774 JW32
C764
IC750
C765
JW16
C432
C435
R431
JW122
JW1
C753
C442
C771
JW24
JW137
JW138
R1
(CHASSIS)
R2
R442
JW19
Q481 C445
R441
VDR1
C
(CHASSIS)
R432
Q431
Q441
C775
JW9
C751
R472
(CHASSIS) Q471
R471
C434
C444
CN580
(BUS CONTROL IN)
JW10
R482
MAIN BOARD
JW17
B
-6
JW12
C454
C464
R
-5
JW13
C331
C330
-4
JC754
-3
JC755
-2
FRONT
L
R
JW34
-1
L
C758
R
R401
L
JW22
J1
(ANATENNA)
C407
A
C622
BUS
AUDIO IN
17
17
(31)
11
12
CDX-GT34W/GT340
4-4.
SCHEMATIC DIAGRAM – MAIN Section (1/3) –
• See page 23 for IC Block Diagram.
C442
C432
C445
C435
C756
R752
C764
JC754 JC755
C765
C774 C753
C757
C761
C775
C776
C758
C755
C751
C771
IC B/D
CN601
IC750
C618
D760
C617
FU601
C752
C750
D759
D617
C763
C769
C770
L601
R580
R588
R590
D584
D582
D583
C582
Q587
D601
C602
D761
D762
D756
D755
D753
Q586
R581
JW46
CN580
(Page 19)
TH580
D754
JC580
R587
C601
C581
R591
JW134
IC B/D
C580
FB604
IC580
IC602
R601
JC581
C503
C683
IC681
R681 C681
C682
C622
C623
JW41
JW113
S702
R554
R555
C519
JC502
Q631
R584
R634
D580
C631
C684
R631
R635
R633
Q479
C632 R632
D479
R582
D511
C479
R583
Q580
Q478
D581
(Page 20)
CDX-GT34W/GT340
18
18
R479
CDX-GT34W/GT340
4-5.
SCHEMATIC DIAGRAM – MAIN Section (2/3) –
• See page 16 for waveform. • See page 24 for IC Block Diagrams.
J330
C452
C462
C444
C455
C434
C465
Q461
Q451
Q441
Q431
Q481
Q471
C464
C454
C403
R462
R452
R442
R432
R482
R330
R472
R461
R451
R441
R431
R481
R471
C461
C451
C441
C431
C481
C471
C402
R332
C330
R333
C331
R331
R2
R1
IC B/D
IC401
ADVANCED TUNER/
RDS DECODER/PLL
IC B/D
C5
L2
R3
FB2
J1
C6
L6
FB1
R401
C1
VDR1
C8
IC1
C19
(Page 18)
L1
C20
C21
C12
C9
L7
L8
C412
C13
C413
FB401
FB402
C405
R4
R5
C23
C24
C25
R11
C404
C409
C16
C408
JC499
C401
C22
C17
R12
C27
R10
C26
R13
R14
C18
C28
X1
JC497
JW144
JC402
JC401
R6
C151
R151
C153
R153
R152
C152
R154
C154
JC151
C155
CN701
L151
C157
R155
(Page 22)
D153
D703
D719
D704
C705
C709
C719
C708
C707
C706
C406
C407
(Page 20)
C551
JW104
JW105
CDX-GT34W/GT340
19
19
CDX-GT34W/GT340
4-6.
SCHEMATIC DIAGRAM – MAIN Section (3/3) –
• See page 16 for waveforms. • See page 26 for IC Pin Function Description of IC501.
(Page 18)
R636
R531
R534
R563
R556
C504
R692
R523
R566
R691
R575
R526
R507
R538
R551
R550
JC303
FB309
FB312
FB311
C301
C308
R506
C501
C302
C514
C512
R301
C312
R663
R661
JC301
R302
C343
C522
C523
FB304
R539
CNP301
R664
R662
R500
R530
R675
R676
C310
R672
IC501
C309
R504
R528
FB308
R674
R505
(Page 19)
R502
R503
R578
R565
D510
JC302
R671
C305
C306
R516
R673
C513
R517
R567
D512
R756
C521
C520
R522
R521
R677
R543
X501
R529
C508
C507
R533
R542
JC501
R519
X502
20
C510
R508
D502
20
R512
R570
R532
R513
JW119
R514
R553
R547
CN351
CDX-GT34W/GT340
R509
R510
R501
R511
R679
R561
R558
C509
JC521
CDX-GT34W/GT340
4-7.
PRINTED WIRING BOARD – KEY Section –
2
1
3
•
: Uses unleaded solder.
4
5
6
7
8
9
10
11
12
13
14
A
LED955
LED949
S907
LED944
52
1
S903
LED952
S905
LCD901
LIQUID CRYSTAL DISPLAY PANEL
LED931
(LCD BACK LIGHT)
S901
LED948
LED946
LED931
S902
S906
LED961
LED946,S905
.m
SEEK–
LED947
S904
LED952,S906
MODE
C
LED944
(CD SLOT)
LED960
LED951,S902
EQ3
LED945
LED956 LED951
M>
SEEK+
SOURCE/OFF
LED950
B
LED949,955
GUIDE BUTTON
SOURCE
LED945,S904
LED940,S907
Z
LED940
LED947,S903
LSW902
LSW903
LSW905
LSW904
LSW907
LSW906
R989
R988
LSW908
21
D
1-880-258LED950,956
GUIDE BUTTON
DSPL
LED948,S901
DSPL/SCRL
LSW903
1/ALBUM–
LSW902
LED960,961
(ILLUMINATION)
PTY/CAT
LSW905
3/REP
LSW904
2/ALBUM+
LSW906
LSW907
LSW908
4/SHUF
5
6/PAUSE
(21)
(Page 17)
MAIN BOARD CN701
A
E
33
32
2
D983
R974
D985
FB902
FB901
FB903
CDX-GT34W/GT340
ECB
R962
H
J901
J901
AUX
R941
Q931
R933
ECB
S909
PUSH SELECT
(VOLUME)
IC902
R934
R935
R942
D903
R931
16
17
IC902
D986
1
R981
D994
R906
R905
R966
R972
49
48
R982
R921
R922
S909
R960
C971
D992
D993
D991
5
R979
4
R977
R978
R903
R902
3
1 64
IC901
R964
2
14
R901
G
1
CN901
C981
R983
R959
F
15
R990
R975
R995
R936
R904
R908
C983
R993
R919
R912
R991
C986
R965
R911
R992
R963
R961
R980
R910
R907
R987
D982
C984
R997 R996
R973
Q932
21
1-880-258-
21
21
(21)
CDX-GT34W/GT340
4-8.
SCHEMATIC DIAGRAM – KEY Section –
1
2
3
4
5
6
KEY BOARD
7
8
LED949,955
(GUIDE BUTTON SOURCE)
9
10
11
12
13
LED960,961
(ILLUMINATION)
A
R972
470
5
IC902
PNA4813M01S0
REMOTE CONTROL
SIGNAL RECEIVER
R982
150
LED961
CL-197HB1E-D-T
4
6
VCC
OUT
GND
5.2
5.1
LSW907
5
R980
470
C971
0.1
3
5
2
4
6
1
3
5
2
4
6
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
1
LSW906
R936
470
4
/SHUF
R911
1.8k
MAZ8180GMLS0
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
S4
S3
COM4
COM3
COM2
COM1
S2
LSW905
3
/REP
R992
270
1
3
5
2
4
6
1
3
5
2
4
6
D982
MA2J1110GLS0
R991
470
MAZ8051GMLS0
MAZ8068GMLS0
3
IC902
6
/PAUSE
R990
270
D903
D994
MAZ8068GMLS0
MAZ8068GMLS0
1
2
MODE
R963
470
LED950,956
(GUIDE BUTTON DSPL)
D992
D993
6
R912
2.2k
1
D986
D985
D991
4
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
R983
470
5.1
J901
AUX
2
R987
1M
2
/ALBUM+
R910
1.5k
R908
1.2k
C986
0.47
0.1
C984
0.1
S1
CE
R977
CLK R978
DATA R979
2.6
4.7
100 0.3
100 3.1
100
3
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
SEG4
SEG3
COM4
COM3
COM2
COM1
S2
VDD
VDD1
VDD2
VSS
S52/OSC
INH
CE
CLK
DATA
1
F
2
3
4
5
6
7
8
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
9 10 11 12 13 14 15 16
1
/ALBUM-
S48
S47
S46
S45
S44
S43
S42
S41
S40
S39
S38
S37
LSW903
R993
470
IC901
IC901
LC75829PWH-US-H
LCD DRIVE
5.1
5.2
E
D983
LSW904
C981
0.1
C983
2.6
2.6
2.6
2.6
2.6
2.6
2.6
5.2
3.5
1.7
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
2.6
4
3
2
5
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
Q932
RT1N436C-TP-1
LCD BACK LIGHT SWITCH
3
LSW908
R988
3.9k
R959
470
LED952
CL-197HB1E-D-T
LED956
CL-197HB1E-D-T
DSPL
0.1
1
R975
100
EQ3
R961
470
LED950
CL-197HB1E-D-T
5.2
LED948
CL-197HB1E-D-T
Q931
RT1N140C-TP-1
DIMMER SWITCH
R981
150
R919
3.3k
LED946
CL-197HB1E-D-T
0.1
R989
270
BACK-LIGHT
DIMMER
NCO
BLINK
SEG48
SEG47
SEG46
SEG45
SEG44
SEG43
SEG42
SEG41
SEG40
SEG39
SEG38
SEG37
LED960
CL-197HB1E-D-T
LED951
CL-197HB1E-D-T
LED955
CL-197HB1E-D-T
LED949
CL-197HB1E-D-T
LED947
CL-197HB1E-D-T
LED945
CL-197HB1E-D-T
R973
560
R960
470
R941
470
R931
1.2k
R974
100
FB902
FB901
D
R933
220
R962
470
SOURCE
R965
470
R942
390
LED940
CL-197HB1E-D-T
11
10
9
8
7
6
5
0
0
(Page 19)
13
12
(CD SLOT)
R934
220
CLK
CE
DATA
MAZ8068GMLS0
MAZ8068GMLS0
MAZ8068GMLS0
A
15
14
R935
270
R964
470
0
MAIN
BOARD
(2/3)
CN701
PANEL
ILL+B
LCD-CLK
LCD-CE
LCD-DATA
SIRCS
KEY-0
KEY-1
RE-1
RE-0
A-GND
AUX-R
AUX-L
KEY_GND
D_GND
FB903
B
C
LCD
BACK
LIGHT
CN901
15P
LED944
CL-197HB1E-D-T
LED931
NESW505CT-AST
R966
470
R995
470
1
3
5
2
4
6
LSW902
S909
R901
820
R902
1k
R903
1k
R922 R921
0
0
R904
1.2k
R907
1k
G
R905
820
S904
SEEK+
S902
EQ3
R906
1k
S905
SEEK-
S901
DSPL
/SCRL
PUSH SELECT
(VOLUME)
LCD901
LIQUID CRYSTAL DISPLAY PANEL
S906
MODE
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
COM1
COM2
COM3
COM4
S48
S47
S46
S45
S44
S43
S42
S41
S40
S39
S38
S37
S36
S35
S34
S33
S32
S31
S30
S29
S28
S27
S26
S25
S24
S23
S22
S21
S20
S19
S18
S17
S16
S15
S14
S13
S12
S11
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S903
SOURCE
OFF
CDX-GT34W/GT340
R996
390
R997
390
S907
H
PTY
/CAT
22
22
S21
S22
S23
S24
S25
S26
S27
S28
S29
S30
S31
S32
S33
S34
S35
S36
CDX-GT34W/GT340
• IC Block Diagrams
IC750 TDA8588AJ/N2/R1 (MAIN Board (1/3))
TAB 1
2 SDA
OUT–FL– 3
I2C BUS
4 SCL
FL
OUT–FL+ 5
6 VP2
OUT–RL– 7
RL
8 PGND1
OUT–RL+ 9
PROTECTION/
DIAGNOSTIC
IN–RR 15
12 IN–FL
14 IN–FR
MUTE
S–GND 13
10 SVR
MUTE
IN–RL 11
16 BEEP
VP
OUT–RR+ 17
18 PGND3
RR
OUT–RR– 19
20 VP1
OUT–FR+ 21
FR
OUT–FR– 23
STANDBY/
MUTE
22 STB
CHIP DETECT/
DIAGNOSTIC
24 PGND4
BATTERY
DETECTION
DIAG 25
TEMPERATURE
PROTECTION
ENABLE
LOGIC
26 RST
ANT–REM 27
SWITCH
AMP–REM 29
SWITCH
28 CRES
30 AUDIO+B
REGULATOR
SERVO3.3V 31
MECH6V 33
32 GND
34 PANEL+B
VP 35
REFERENCE
VOLTAGE
BU+B 37
REGULATOR
36 CBU
LOADDUMP
PROTECTION
BACK-UP
SWITCH
23
CDX-GT34W/GT340
IC580 BA8271F-E2 (MAIN Board (1/3))
BUS_ON 1
BUS ON
SWITCH
RST 2
RESET
SWITCH
BATT 3
BATTERY
SWITCH
CLK 4
VREF 5
DATA_I/O 6
14 VCC
13
12
11
10
RST
BUS_IN
CLK_IN
BU_CHECK
9 DATA_IN
GND 7
8 DATA_OUT
IC1 TEF6617T/V1/S470,518 (MAIN Board (2/3))
AMRFIN 1
32 AMSELOUT2
AM
TUNER
AMRFDEC 2
FMIN2 3
FMIN1 4
31 AMSELOUT1
30 AMIFAGC1
FM
TUNER
29 AMSELIN2
28 AMSELIN1
GNDRF 5
27 DAV N
VCC2 6
RDS
DEMODULATOR
AND
DECODER
AMRFAGC 7
LOUT 8
ROUT 9
GNDAUD 10
OUTPUT
STEREO DECODER
HIGH CUT
SOFT MUTE
NOISE BLANKER
AMIFAGC2 11
MPXIN 12
MPXOUT 13
RSSI 14
XTAL2 15
XTAL1 16
24
26 PLLREF
PLL
TUNING
SYSTEM
25 PLL
24 VCODEC
23 GND
POWER
SUPPLY
SIGNAL
IMPROVEMENT
CONTROL
BANDWIDTH
CONTROL
22 VCC1
21 VREGSUP
20 VREF
19 SDA
I2C BUS
18 SCL
17 GNDD
CDX-GT34W/GT340
FIL
A-GND
SDA
SCL
VCC
OUT-FR
OUT-FL
OUT-RR
OUT-RL
SUB-R
SUB-L
SAOUT
SADA
SACLK
MIN1
MIN2
EBIAS2
DS2-R
DS1-R
DS3-R
IC401 BD3447AFV-E2 (MAIN Board (2/3))
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23 22
21
I2C BUS
LOGIC,
VCO
FADER
FADER
FADER
FADER
FADER
EFFECT
LPF
180°/0°
HPF
3 BAND P-EQ (TONE CONTROL)
7 BAND
SPECTRUM ANALYZER
/LEVEL METER
VOLUME/MUTE
LVL METER
SPEANA
LVL METER
SPEANA
INPUT GAIN
DS3-R
10
11
12
13
14
DS2-L
9
FN1
DS1-R
8
FP1
EBIAS1
7
EP2
FN2
6
EN
20
5
EP1
18 19
4
AUX-R
17
3
AUX-G
16
2
AUX-R
15
1
CD-L
GND
ISO AMP
CD-R
GND
ISO AMP
TU-L
GND
ISO AMP
TU-R
GND
ISO AMP
BUS-L
GND
ISO AMP
BUS-R
GND
ISO AMP
EP2
INPUT SELECTOR (3 SIGLE-END AND 3 STEREO IS O)
25
CDX-GT34W/GT340
• IC Pin Function Description
MAIN BOARD IC501 R5F3640DDA15FA (SYSTEM CONTROL)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22 to 27
28
29
30
31
32
33
34
35 to 40
41
42
43
44
45
46
47 to 51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
26
Pin Name
LCD SO
LCD CKO
NOSE SW
SIRCS
UNISO
UNISI
UNISCK
BYTE
CNVSS
XIN
XOUT
RESET
OSCOUT
VSS
OSCIN
VCC1
NMI
EQ SEL
BUIN
CDM ON
Z MUTE
NCO
BEEP
I2C SCK
I2C SIO
FW TXD
FW RXD
FW CLK
FW BUSY
NCO
EPM
RC IN1
SYSRST
BUSON
NCO
CE
NCO
CD ON
TESTIN
TELATT
ACC IN
ATT
DIAG
AMPSTB
NCO
NCO/BT AUDIO SEL
NCO
VCC2
COL SEL/NCO
VSS
ILLUMI SEL
DEMO SEL
DIM SEL
B OUT SEL
AREASEL 3
AREASEL 2
I/O
O
O
I
I
O
I
O
I
I
I
O
I
O
—
I
—
I
O
I
I
I
O
O
O
I/O
O
I
I
O
O
O
I
O
O
O
O
O
I
I
I
I
O
I
O
O
O
O
—
O
—
I
I
I
I
I
I
Description
Liquid crystal display panel serial data signal output
Liquid crystal display panel serial clock signal output
Front Panel detach/attach detect signal input “L”: With panel
Remote control signal input
SONY BUS serial data signal output
SONY BUS serial data signal input
SONY BUS serial clock signal output
Connect to ground.
Flash write signal input Normally operation: “L”, Flash write: “H”
Low speed operation clock signal input (32.768kHz)
Low speed operation clock signal output (32.768kHz)
Reset signal input
High speed operation clock signal output (11.06MHz)
Ground pin
High speed operation clock signal input (11.06MHz)
Power supply pin (+3.3V)
External pull up pin (fixed at “H”.)
Not used. (fixed at “L”.)
Back up power supply detection signal input
CD mechanism deck power supply control request signal input
Mute signal input
Not used. (Open)
Beep signal output to power amplifier
I2C serial clock signal output
I2C serial data signal input/output
Flash write interface serial data signal output
Flash write interface serial data signal input
Flash write interface serial clock signal input
Flash write interface serial busy signal output
Not used. (Open)
EPM signal output (Connect to ground.)
Rotary commander shift key signal input Not used.
System reset signal output
BUS ON signal output
Not used. (Open)
CE signal output
Not used. (Open)
CD mechanism servo power supply control request signal input
Test mode detection signal input Not used.
Telephone attenuate detection signal input Not used.
Accessory power supply detection signal input
Audio mute control signal output
Power amplifier status signal input
Standby signal output to power regulator IC
Not used. (Open)
Not used. (Open)
Not used.
Power supply pin (+3.3V)
Not used.
Ground pin
Illumination voltage setting signal input for panel
DEMO select signal input “H”: DEMO on
Dimmer function setting signal input “L”: No dimmer
Black out setting signal input “L”: No block out
Destination setting pin 3
Destination setting pin 2
CDX-GT34W/GT340
Pin No.
71
72
73 to 80
81
82
83
Pin Name
AREASEL 1
AREASEL 0
NCO
RE IN1
RE IN0
NCO/SA IN
I/O
I
I
O
I
I
I
84
CYRIL SEL
I
85 to 88
89
90
91
92
93
94
95
96
97
98
99
100
NCO
NCO/SADATD
NCO/SACLK
KEYACK0
KEYACK1
VSM
KEYIN1
KEYIN0
AVSS
RC IN0
AVRH
AVDD
LCD CE
O
O
O
I
I
I
I
I
—
I
—
—
O
Description
Destination setting pin 1
Destination setting pin 0
Not used. (Open)
Rotary encoder signal input 1
Rotary encoder signal input 0
Serial data signal input to electronic volume spectrum analyzer
Cyril correspondence discrimination signal input
“H”: Correspondence, “L”: No correspondence
Not used. (Open)
Serial data signal output to electronic volume spectrum analyzer
Serial clock signal output to electronic volume spectrum analyzer
Key Acknowledge detection signal input (Rotary command signal input)
Key Acknowledge detection signal input (Front panel signal input)
S meter voltage detection signal input
Key signal input 1
Key signal input 0
Ground pin for A/D converter
Rotary commander key signal input Not used.
A/D converter external reference power supply pin (+3.3V)
A/D converter power supply pin (+3.3V)
Liquid crystal display panel chip enable signal output
Not used.
27
CDX-GT34W/GT340
SECTION 5
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine service. Some delay should be anticipated
when ordering these items.
• The mechanical parts with no reference
number in the exploded views are not supplied.
5-1.
• Color Indication of Appearance Parts Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet’s Color
• Accessories are given in the last of the
electrical parts list.
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro spécifié.
MAIN SECTION
not supplied
A
MG-101L-188//Q
#2
6
#1
#3
B
A
#4
FU601
#5
#4
#5
4
#3
#4
not supplied
5
not supplied
3
#1
not supplied
B
2
#1
not supplied
#1
not supplied
1
front panel section
Ref. No.
Part No.
Description
Part No.
Description
1
2
3
4
5
X-2514-277-1
3-042-244-11
X-2179-399-1
2-050-124-01
A-1731-287-A
PANEL ASSY, SUB
SCREW (T)
LOCK ASSY (S)
SCREW +BTT 2.6X5
MAIN BOARD, COMPLETE
FU601
#1
#2
#3
#4
1-532-877-11
7-685-792-09
7-685-790-01
7-685-793-09
7-685-794-09
FUSE (BLADE TYPE) (AUTO FUSE) 10A
SCREW +PTT 2.6X6 (S)
SCREW +PTT 2.6X4 (S)
SCREW +PTT 2.6X8 (S)
SCREW +PTT 2.6X10 (S)
6
1-833-974-21
CONNECTION CORD FOR AUTOMOBILE
(POWER)
#5
7-685-134-19
SCREW +P 2.6X8 TYPE2 NON-SLIT
28
Remark
Ref. No.
Remark
CDX-GT34W/GT340
5-2.
FRONT PANEL SECTION
60
59
S909
60
not supplied
57
not supplied
(KEY board)
J901
not supplied
58
56
LCD901
not supplied
not supplied
not supplied
not supplied
55
54
52
not supplied
53
51
Ref. No.
Part No.
Description
Remark
51
51
52
53
54
A-1731-290-A
A-1732-175-A
X-2349-669-1
3-251-320-01
X-2514-364-1
PANEL COMPLETE ASSY, FRONT (GT34W)
PANEL COMPLETE ASSY, FRONT (GT340)
BUTTON ASSY (S)
EMBLEM (NO. 2.5), SONY
PANEL (SV) ASSY, FRONT (GT34W)
54
55
56
X-2514-365-1
X-2349-670-1
2-639-881-01
PANEL (SV) ASSY, FRONT (GT340)
KNOB (VOL) (SV) ASSY
SPRING (RELEASE)
Ref. No.
Part No.
Description
Remark
57
58
59
60
J901
1-780-789-11
4-144-557-01
4-144-543-01
3-250-543-21
1-822-148-11
CONDUCTIVE BOARD, CONNECTION
ILLUMINATOR (LCD)
PANEL, BACK
SCREW (+B P-TITE M2)
SMALL TYPE JACK (VERTICAL) (AUX)
LCD901
S909
1-802-952-11
1-479-902-32
DISPLAY PANEL, LIQUID CRYSTAL
ENCODER, ROTARY (PUSH SELECT/VOLUME)
29
CDX-GT34W/GT340
5-3.
CD MECHANISM SECTION
(MG-101L-188//Q)
101
102
not supplied
108
103
not supplied
108
105
not supplied
not supplied
not supplied
not supplied
not supplied
104
not supplied
not supplied
not supplied
not supplied
107
106
Ref. No.
101
102
0 103
104
30
Part No.
Description
A-1539-598-A
A-1284-705-A
X-2149-672-1
2-626-869-31
MECHANICAL BLOCK ASSY (08TC)
DAXEV08//Q
SERVICE ASSY, OP (DAX-25A)
SCREW (M2X3), SERRATION
Remark
106
Ref. No.
105
106
107
108
Part No.
Description
3-686-458-21
3-352-758-31
A-1552-122-A
2-134-636-71
SCREW (P1.4), TAPPING
SCREW (M1.7X2.5), TOOTHED LOCK
SERVO BOARD, COMPLETE
SCREW (M1.7X2.5)
Remark
CDX-GT34W/GT340
SECTION 6
ELECTRICAL PARTS LIST
Note:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine service. Some delay should be anticipated
when ordering these items.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No.
Part No.
• CAPACITORS
uF: μF
• COILS
uH: μH
• SEMICONDUCTORS
In each case, u: μ, for example:
uA. . : μA. . , uPA. . , μPA. . ,
uPB. . : μPB. . , uPC. . , μPC. . ,
uPD. . : μPD. .
Description
Remark
1-780-789-11
4-144-557-01
C971
C981
C983
C984
C986
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-125-891-11
1-819-758-12
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro spécifié.
Part No.
Description
CONDUCTIVE BOARD, CONNECTION
ILLUMINATOR (LCD)
6-501-547-02
6-501-547-02
6-501-547-02
6-501-547-02
6-501-547-02
LED
LED
LED
LED
LED
< CAPACITOR >
LED949
6-501-547-02
LED950
LED951
LED952
LED955
6-501-547-02
6-501-547-02
6-501-547-02
6-501-547-02
LED CL-197HB1E-D-T
(GUIDE BUTTON SOURCE)
LED CL-197HB1E-D-T (GUIDE BUTTON DSPL)
LED CL-197HB1E-D-T (EQ3)
LED CL-197HB1E-D-T (MODE)
LED CL-197HB1E-D-T
(GUIDE BUTTON SOURCE)
LED956
LED960
LED961
6-501-547-02
6-501-547-02
6-501-547-02
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.47uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
10V
< CONNECTOR >
CN901
When indicating parts by reference number, please include the board name.
LED944
LED945
LED946
LED947
LED948
KEY BOARD
**********
PLUG, CONNECTOR 15P
Ref. No.
< DIODE >
6-501-782-01
6-501-817-01
6-501-730-01
6-501-743-01
6-501-743-01
DIODE
DIODE
DIODE
DIODE
DIODE
MAZ8180GMLS0
MA2J1110GLS0
MAZ8051GMLS0
MAZ8068GMLS0
MAZ8068GMLS0
LSW902
LSW903
LSW904
LSW905
LSW906
D991
D992
D993
D994
6-501-743-01
6-501-743-01
6-501-743-01
6-501-743-01
DIODE
DIODE
DIODE
DIODE
MAZ8068GMLS0
MAZ8068GMLS0
MAZ8068GMLS0
MAZ8068GMLS0
LSW907 1-798-285-11
LSW908 1-798-285-11
< JUMPER RESISTOR >
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
6-714-396-01
6-600-764-01
IC LC75829PWH-US-H
IC PNA4813M01S0 (IR)
< JACK >
J901
1-822-148-11
SMALL TYPE JACK (VERTICAL) (AUX)
< LIQUID CRYSTAL DISPLAY >
LCD901
1-802-952-11
DISPLAY PANEL, LIQUID CRYSTAL
< DIODE >
LED931
LED940
6-501-339-01
6-501-547-02
1-798-285-11
1-798-285-11
1-798-285-11
1-798-285-11
1-798-285-11
LED CL-197HB1E-D-T (GUIDE BUTTON DSPL)
LED CL-197HB1E-D-T (ILLUMINATION)
LED CL-197HB1E-D-T (ILLUMINATION)
LED NESW505CT-AST (LCD BACK LIGHT)
LED CL-197HB1E-D-T (Z)
SWITCH, TACTILE (WITH LED) (PTY/CAT)
SWITCH, TACTILE (WITH LED) (1/ALBUM –)
SWITCH, TACTILE (WITH LED) (2/ALBUM +)
SWITCH, TACTILE (WITH LED) (3/REP)
SWITCH, TACTILE (WITH LED) (4/SHUF)
SWITCH, TACTILE (WITH LED) (5)
SWITCH, TACTILE (WITH LED) (6/PAUSE)
< TRANSISTOR >
Q931
Q932
8-729-027-44
6-551-444-01
0
0
0
< IC >
IC901
IC902
Remark
CL-197HB1E-D-T (CD SLOT)
CL-197HB1E-D-T (M >)
CL-197HB1E-D-T (. m)
CL-197HB1E-D-T (SOURCE)
CL-197HB1E-D-T (DSPL)
< SWITCH >
D903
D982
D983
D985
D986
FB901
FB902
FB903
KEY
TRANSISTOR DTC114TKA-T146
TRANSISTOR RT1N436C-TP-1
< RESISTOR >
R901
R902
R903
R904
R905
1-216-820-11
1-216-821-11
1-216-821-11
1-216-822-11
1-216-820-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
820
1K
1K
1.2K
820
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R906
R907
R908
R910
R911
1-216-821-11
1-216-821-11
1-216-822-11
1-216-823-11
1-216-824-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1.2K
1.5K
1.8K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R912
R919
R921
R922
R931
1-216-825-11
1-216-827-11
1-216-864-11
1-216-864-11
1-216-822-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
2.2K
3.3K
0
0
1.2K
5%
5%
1/10W
1/10W
5%
1/10W
31
CDX-GT34W/GT340
KEY
Ref. No.
MAIN
Part No.
Description
Part No.
Description
R933
R934
R935
R936
R941
1-216-813-11
1-216-813-11
1-216-814-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
220
270
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
C17
C18
C19
C20
C21
1-107-826-11
1-162-916-11
1-162-970-11
1-162-970-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
12PF
0.01uF
0.01uF
1uF
10%
5%
10%
10%
10%
16V
50V
25V
25V
10V
R942
R959
R960
R961
R962
1-216-816-11
1-216-817-11
1-216-817-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
390
470
470
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C22
C23
C24
C25
C26
1-162-970-11
1-162-970-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
25V
25V
16V
16V
16V
R963
R964
R965
R966
R972
1-216-817-11
1-216-817-11
1-216-817-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
470
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C27
C28
C151
C152
C153
1-107-826-11
1-126-947-11
1-126-960-11
1-126-960-11
1-126-961-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.1uF
47uF
1uF
1uF
2.2uF
10%
20%
20%
20%
20%
16V
35V
50V
50V
50V
R973
R974
R975
R977
R978
1-216-818-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
560
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C154
C155
C157
C301
C302
1-163-251-11
1-163-251-11
1-162-964-11
1-124-248-00
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
100PF
100PF
0.001uF
22uF
100uF
5%
5%
10%
20%
20%
50V
50V
50V
25V
10V
R979
R980
R981
R982
R983
1-216-809-11
1-216-817-11
1-216-811-11
1-216-811-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
470
150
150
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C305
C306
C308
C309
C310
1-124-584-00
1-162-970-11
1-162-970-11
1-164-739-11
1-164-739-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.01uF
0.01uF
560PF
560PF
20%
10%
10%
5%
5%
10V
25V
25V
50V
50V
R987
R988
R989
R990
R991
1-216-857-11
1-216-828-11
1-216-814-11
1-216-814-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
3.9K
270
270
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C312
C330
C331
C343
C401
1-162-970-11
1-163-251-11
1-163-251-11
1-162-970-11
1-126-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
100PF
100PF
0.01uF
47uF
10%
5%
5%
10%
20%
25V
50V
50V
25V
35V
R992
R993
R995
R996
R997
1-216-814-11
1-216-817-11
1-216-817-11
1-216-816-11
1-216-816-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
270
470
470
390
390
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C402
C403
C404
C405
C406
1-126-960-11
1-126-960-11
1-165-908-11
1-165-908-11
1-126-160-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
1uF
1uF
1uF
1uF
1uF
20%
20%
10%
10%
20%
50V
50V
10V
10V
50V
C407
C408
C409
C412
C413
1-126-160-11
1-162-915-11
1-162-915-11
1-126-934-11
1-107-826-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
1uF
10PF
10PF
220uF
0.1uF
20%
0.5PF
0.5PF
20%
10%
50V
50V
50V
16V
16V
C431
C432
C434
C435
C441
1-126-964-11
1-165-908-11
1-163-251-11
1-165-908-11
1-126-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
10uF
1uF
100PF
1uF
10uF
20%
10%
5%
10%
20%
50V
10V
50V
10V
50V
C442
C444
C445
C451
C452
1-165-908-11
1-163-251-11
1-165-908-11
1-126-964-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
1uF
100PF
1uF
10uF
1uF
10%
5%
10%
20%
10%
10V
50V
10V
50V
10V
C454
C455
C461
C462
C464
1-163-251-11
1-165-908-11
1-126-964-11
1-165-908-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
100PF
1uF
10uF
1uF
100PF
5%
10%
20%
10%
5%
50V
10V
50V
10V
50V
C465
C471
C479
C481
C501
1-165-908-11
1-126-964-11
1-124-589-11
1-126-964-11
1-162-970-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
1uF
10uF
47uF
10uF
0.01uF
10%
20%
20%
20%
10%
10V
50V
16V
50V
25V
< SWITCH >
S901
S902
S903
S904
S905
1-798-284-11
1-798-284-11
1-798-284-11
1-798-284-11
1-798-284-11
SWITCH, TACTILE (DSPL/SCRL)
SWITCH, TACTILE (EQ3)
SWITCH, TACTILE (SOURCE/OFF)
SWITCH, TACTILE (M > SEEK+)
SWITCH, TACTILE (. m SEEK–)
S906
1-798-284-11 SWITCH, TACTILE (MODE)
S907
1-798-284-11 SWITCH, TACTILE (Z)
S909
1-479-902-32 ENCODER, ROTARY (PUSH SELECT/VOLUME)
*************************************************************
A-1731-287-A
MAIN BOARD, COMPLETE
*********************
7-685-134-19
7-685-794-09
SCREW +P 2.6X8 TYPE2 NON-SLIT
SCREW +PTT 2.6X10 (S)
< CAPACITOR >
C1
C5
C6
C8
C9
1-162-964-11
1-162-964-11
1-162-917-11
1-162-921-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C12
C13
C16
1-127-715-11
1-100-742-91
1-125-891-11
CERAMIC CHIP 0.22uF
CERAMIC CHIP 2.2uF
CERAMIC CHIP 0.47uF
32
0.001uF
0.001uF
15PF
33PF
0.1uF
10%
10%
5%
5%
10%
50V
50V
50V
50V
16V
10%
20%
10%
16V
10V
10V
Ref. No.
Remark
CDX-GT34W/GT340
MAIN
Ref. No.
Part No.
Description
C503
C504
C507
C508
C509
1-104-665-11
1-162-970-11
1-162-917-11
1-162-918-11
1-162-966-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.01uF
15PF
18PF
0.0022uF
20%
10%
5%
5%
10%
25V
25V
50V
50V
50V
Remark
C510
C512
C513
C514
C519
1-162-970-11
1-162-964-11
1-162-970-11
1-162-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.001uF
0.01uF
0.001uF
0.1uF
10%
10%
10%
10%
10%
25V
50V
25V
50V
16V
C520
C521
C522
C523
C551
1-162-923-11
1-162-923-11
1-162-970-11
1-162-970-11
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47PF
47PF
0.01uF
0.01uF
0.001uF
5%
5%
10%
10%
5%
50V
50V
25V
25V
25V
C580
C581
C582
C601
C602
1-162-970-11
1-126-941-11
1-165-319-11
1-112-302-11
1-165-319-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.01uF
470uF
0.1uF
3300uF
0.1uF
10%
20%
25V
25V
50V
16V
50V
C617
C618
C622
C623
C631
1-163-009-91
1-163-009-91
1-126-926-11
1-126-926-11
1-107-823-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
0.001uF
0.001uF
1000uF
1000uF
0.47uF
10%
10%
20%
20%
10%
50V
50V
10V
10V
16V
C632
C681
C682
C683
C684
1-107-823-11
1-107-826-11
1-107-826-11
1-124-261-00
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.47uF
0.1uF
0.1uF
10uF
0.001uF
10%
10%
10%
20%
10%
16V
16V
16V
50V
50V
C705
C706
C707
C708
C709
1-162-918-11
1-162-918-11
1-162-918-11
1-162-918-11
1-162-918-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
18PF
18PF
18PF
18PF
18PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C719
C750
C751
C752
C753
1-163-009-91
1-115-340-11
1-115-340-11
1-124-589-11
1-128-551-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.001uF
0.22uF
0.22uF
47uF
22uF
10%
10%
10%
20%
20%
50V
25V
25V
16V
63V
C755
C756
C757
C758
C761
1-162-964-11
1-216-864-11
1-125-889-11
1-124-261-00
1-126-176-11
CERAMIC CHIP
SHORT CHIP
CERAMIC CHIP
ELECT
ELECT
0.001uF
0
2.2uF
10uF
220uF
10%
50V
10%
20%
20%
10V
50V
10V
C763
C764
C765
C769
C770
1-127-715-11
1-115-340-11
1-115-340-11
1-127-715-11
1-127-715-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.22uF
0.22uF
0.22uF
0.22uF
10%
10%
10%
10%
10%
16V
25V
25V
16V
16V
C771
C774
C775
C776
1-165-908-11
1-115-340-11
1-115-340-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.22uF
0.22uF
0.001uF
10%
10%
10%
10%
10V
25V
25V
50V
20%
< CONNECTOR >
* CN351
CN580
CN601
CN701
CNP301
1-564-710-11
1-580-907-41
1-774-701-21
1-819-773-21
1-820-611-11
PIN, CONNECTOR (SMALL TYPE) 8P
PLUG, CONNECTOR 8P (BUS CONTROL IN)
PIN, CONNECTOR 16P
SOCKET, CONNECTOR 15P
CONNECTOR, BOARD TO BOARD 28P
Ref. No.
Part No.
Description
Remark
< DIODE >
D153
D479
D502
D510
D511
8-719-978-33
6-501-817-01
6-502-131-01
6-501-656-01
6-500-335-01
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ-TT11-6.8B
MA2J1110GLS0
LRB751V-40T1G
LBAT54ALT1G
MC2838-T112-1
D512
D580
D581
D582
D583
6-501-654-01
6-501-738-01
6-501-782-01
6-501-782-01
8-719-072-70
DIODE
DIODE
DIODE
DIODE
DIODE
LBAT54CLT1G
MAZ8062GMLS0
MAZ8180GMLS0
MAZ8180GMLS0
MA2ZD14001S0
D584
D601
D617
D703
D704
6-501-782-01
6-501-571-01
6-501-782-01
6-501-743-01
6-501-743-01
DIODE
DIODE
DIODE
DIODE
DIODE
MAZ8180GMLS0
1N5404-C311-3
MAZ8180GMLS0
MAZ8068GMLS0
MAZ8068GMLS0
D719
D753
D754
D755
D756
6-501-782-01
6-502-643-01
6-502-643-01
6-502-643-01
6-502-643-01
DIODE
DIODE
DIODE
DIODE
DIODE
MAZ8180GMLS0
1A4-A2
1A4-A2
1A4-A2
1A4-A2
D759
D760
D761
D762
6-502-643-01
6-502-643-01
6-502-643-01
6-502-643-01
DIODE
DIODE
DIODE
DIODE
1A4-A2
1A4-A2
1A4-A2
1A4-A2
< FERRITE BEAD >
FB1
FB2
FB304
FB308
FB309
1-400-334-21
1-400-334-21
1-469-777-21
1-414-233-22
1-216-864-11
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
SHORT CHIP
0
FB311
FB312
FB401
FB402
FB604
1-469-777-21
1-400-382-11
1-400-334-21
1-400-334-21
1-216-295-91
INDUCTOR, FERRITE BEAD
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
SHORT CHIP
0
< IC >
IC1
IC401
IC501
IC580
IC602
6-714-162-01
6-713-080-11
6-808-750-01
6-703-884-01
6-712-776-01
IC
IC
IC
IC
IC
TEF6617T/V1/S470,518
BD3447AFV-E2
R5F3640DDA15FA
BA8271F-E2
PST8228UL
IC681
IC750
6-702-302-01
6-705-359-02
IC TK11133CSCL-G
IC TDA8588AJ/N2/R1
< JACK >
J1
J330
1-815-185-13
1-774-700-41
JACK (ANTENNA)
JACK, PIN 6P (BUS AUDIO IN,
AUDIO OUT FRONT,REAR/SUB)
< JUMPER RESISTOR >
JC151
JC301
JC302
JC303
JC401
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC402
JC497
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
0
0
33
CDX-GT34W/GT340
MAIN
Ref. No.
Part No.
Description
Part No.
Description
JC499
JC501
JC502
JC521
JC580
1-216-295-91
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
Remark
R451
R452
R461
R462
R471
1-216-821-11
1-216-833-11
1-216-821-11
1-216-833-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
1K
10K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
JC581
JC754
JC755
1-216-864-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
R472
R479
R481
R482
R500
1-216-833-11
1-216-801-11
1-216-813-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
22
220
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R501
R502
R503
R504
R505
1-219-570-11
1-216-821-11
1-216-821-11
1-218-871-11
1-218-871-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10M
1K
1K
10K
10K
5%
5%
5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R506
R507
R508
R509
R510
1-216-845-11
1-216-845-11
1-216-849-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
100K
100K
220K
0
1K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R511
R512
R513
R514
R516
1-216-821-11
1-216-821-11
1-216-845-11
1-216-845-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
1K
1K
100K
100K
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R517
R519
R521
R522
R523
1-216-864-11
1-216-845-11
1-216-825-11
1-216-825-11
1-216-845-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100K
2.2K
2.2K
100K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R526
R528
R529
R530
R531
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R532
R533
R534
R538
R539
1-216-845-11
1-216-845-11
1-216-833-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
10K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R542
R543
R547
R550
R551
1-216-821-11
1-216-821-11
1-216-821-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R553
R554
R555
R556
R558
1-216-845-11
1-216-851-11
1-216-851-11
1-216-833-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
330K
330K
10K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R561
R563
R565
R566
R567
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R570
R575
R578
R580
R581
1-216-817-11
1-216-845-11
1-216-821-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
100K
1K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< COIL >
L1
L2
L6
L7
L8
1-414-180-51
1-410-501-61
1-457-817-11
1-481-285-51
1-481-285-51
INDUCTOR
INDUCTOR
COIL (FM MIX)
INDUCTOR
INDUCTOR
3.3uH
2.2uH
L151
L601
1-216-295-91
1-456-617-11
SHORT CHIP
COIL, CHOKE
0
560uH
560uH
< TRANSISTOR >
Q431
Q441
Q451
Q461
Q471
6-551-856-01
6-551-856-01
8-729-027-44
8-729-027-44
6-551-856-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
LTC614TKFP8T146
LTC614TKFP8T146
DTC114TKA-T146
DTC114TKA-T146
LTC614TKFP8T146
Q478
Q479
Q481
Q580
Q586
8-729-027-43
8-729-027-23
6-551-856-01
8-729-027-43
8-729-027-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146
DTA114EKA-T146
LTC614TKFP8T146
DTC114EKA-T146
DTA114EKA-T146
Q587
Q631
8-729-047-76
8-729-620-07
TRANSISTOR FMC2A-T148
TRANSISTOR 2SC3052EF-T1-LEF
< RESISTOR >
R1
R2
R3
R4
R5
1-216-853-11
1-216-853-11
1-400-334-21
1-216-864-11
1-216-864-11
METAL CHIP
470K
5%
METAL CHIP
470K
5%
FERRITE, EMI (SMD) (1608)
SHORT CHIP
0
SHORT CHIP
0
1/10W
1/10W
R6
R10
R11
R12
R13
1-216-843-11
1-216-839-11
1-216-829-11
1-216-009-91
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
68K
33K
4.7K
22
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R14
R151
R152
R153
R154
1-216-809-11
1-216-817-11
1-216-817-11
1-216-834-11
1-216-834-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
470
470
12K
12K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R155
R301
R302
R330
R331
1-216-825-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R332
R333
R401
R431
R432
1-216-833-11
1-216-833-11
1-216-797-11
1-216-813-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10
220
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R441
R442
1-216-813-11
1-216-833-11
METAL CHIP
METAL CHIP
220
10K
5%
5%
1/10W
1/10W
34
Ref. No.
Remark
CDX-GT34W/GT340
MAIN
Ref. No.
Part No.
Description
R582
R583
R584
R587
R588
1-216-835-11
1-216-821-11
1-216-849-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
1K
220K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
Ref. No.
Part No.
R590
R591
R601
R631
R632
1-216-864-11
1-216-829-11
1-216-845-11
1-216-073-91
1-216-841-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
4.7K
100K
10K
47K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
4-149-110-21
R633
R634
R635
R636
R661
1-216-841-11
1-216-829-11
1-216-073-91
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
4.7K
10K
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
4-149-111-21
R662
R663
R664
R671
R672
1-216-833-11
1-216-821-11
1-216-833-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R673
R674
R675
R676
R677
1-218-871-11
1-216-845-11
1-216-821-11
1-216-821-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
10K
100K
1K
1K
0
0.5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R679
R681
R691
R692
R752
1-216-821-11
1-216-833-11
1-216-845-11
1-216-845-11
1-216-811-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
100K
100K
150
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R756
1-216-841-11
METAL CHIP
47K
5%
1/10W
Description
SERVO
Remark
ACCESSORIES
************
1-479-077-14
2-548-729-01
4-149-110-11
4-149-111-11
REMOTE COMMANDER (RM-X151)
LID, BATTERY CASE (for RM-X151)
MANUAL, INSTRUCTION (ENGLISH,FRENCH,
SPANISH) (GT34W)
MANUAL, INSTRUCTION (ENGLISH,FRENCH)
(GT340)
MANUAL, INSTRUCTION, INSTALL (ENGLISH,
FRENCH,SPANISH) (GT34W)
MANUAL, INSTRUCTION, INSTALL (ENGLISH,
FRENCH) (GT340)
*************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
151
152
X-2179-431-2
1-833-974-21
153
154
155
3-876-675-01
4-144-560-01
3-934-325-01
151
FRAME ASSY, FITTING
CONNECTION CORD FOR AUTOMOBILE
(POWER)
KEY (FRAME)
COLLAR
SCREW, +K (5X8) TAPPING
152
153
u2
154
155
< SWITCH >
S702
1-786-826-11
SWITCH, TACTILE (RESET)
u4
< THERMISTOR (POSITIVE) >
TH580
1-803-350-21
THERMISTOR, POSITIVE
< SURGE ABSORBER >
VDR1
1-805-043-11
ABSORBER, CHIP SURGE
< VIBRATOR >
X1
1-814-300-11 QUARTZ CRYSTAL UNIT (4MHz)
X501
1-814-075-21 VIBRATOR, CERAMIC (11.06MHz)
X502
1-767-317-11 VIBRATOR, CRYSTAL (32.768kHz)
*************************************************************
A-1552-122-A
SERVO BOARD, COMPLETE
**********************
*************************************************************
MISCELLANEOUS
**************
6
1-833-974-21
CONNECTION CORD FOR AUTOMOBILE
(POWER)
0 103
X-2149-672-1 SERVICE ASSY, OP (DAX-25A)
FU601
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
*************************************************************
35
CDX-GT34W/GT340
REVISION HISTORY
Checking the version allows you to jump to the revised page.
Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver.
Date
1.0
2009.07
Description of Revision
New