Download CDX-GT800D/GT805DX

CDX-GT800D/GT805DX
SERVICE MANUAL
US Model
CDX-GT805DX
E Model
Chinese Model
Ver. 1.0 2005.12
CDX-GT800D
Photo: CDX-GT805DX
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
NEW
AUDIO POWER SPECIFICATIONS (US MODEL)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD Drive Mechanism Type
MG-611WD-186//Q
Optical Pick-up Name
KSS1000E
SPECIFICATIONS
CD player section
Signal-to-noise ratio
Frequency response
Wow and flutter
Power amplifier section
Outputs
Speaker outputs (sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 52 W × 4 (at 4 ohms)
120 dB
10 – 20,000 Hz
Below measurable limit
Tuner section
FM
Tuning range
General
Outputs
CDX-GT805DX: 87.5 – 107.9 MHz
CDX-GT800D: 87.5 – 108 MHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM (CDX-GT805DX)
Tuning range
Antenna terminal
Intermediate frequency
Sensitivity
2005L04-1
© 2005.12
Loudness
– Continued on next page –
530 – 1,710 kHz
External antenna connector
10.7 MHz/450 kHz
30 µV
MW/LW (CDX-GT800D)
Tuning range
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
MW: 30 µV
LW: 40 µV
9-879-999-01
Inputs
Audio outputs terminal (front/rear)
Subwoofer output terminal (mono)
Power antenna relay control terminal
Power amplifier control terminal
Telephone ATT control terminal
Illumination control terminal
BUS control input terminal
BUS audio input/AUX IN terminal
Remote controller input terminal
Antenna input terminal
+8 dB at 100 Hz
+0 dB at 10 kHz
FM/AM COMPACT DISC PLAYER
CDX-GT805DX
FM/MW/LW COMPACT DISC PLAYER
Sony Corporation
eVehicle Division
Published by Sony Engineering Corporation
CDX-GT800D
CDX-GT800D/GT805DX
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
12 V DC car battery
(negative ground)
Approx. 178 × 50 × 188 mm
(7 1/8 × 2 × 7 1/2 in.) (w/h/d)
Approx. 182 × 53 × 162 mm
(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d)
Approx. 1.6 kg
(4 lb.)
Parts for installation and connections (1 set)
Card remote commander RM-X152
(CDX-GT805DX)
Card remote commander RM-X154
(CDX-GT800D)
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical pickup block.
optical pick-up
US and foreign patents licensed from Dolby Laboratories.
Note
This unit cannot be connected to a digital preamplifier or an equalizer
which is Sony BUS system compatible.
Design and specifications are subject to change without
notice.
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
semi-fixed resistor
• E model
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
This label is located on the bottom of the chassis.
• Chinese model
CDX-GT800D/GT805DX
• CD Playback:
You can play CD-DA (also containing CD TEXT*1), CD-R/CDRW (MP3/MWA files also containing Multi Session and ATRAC
CD (ATRAC3 and ATRAC3plus format).
Type of discs
NOTE FOR THE OPENING OF THE FRONT PANEL
In this set, the front panel is lowered to below the bottom face when
it is opened.
When servicing the set, place it on a stand having a height of about
2 cm.
Label on the disc
CD-DA
MP3
MWA
ATRAC CD
stand
*1 A CD TEXT disc is a CD-DA that includes information such as
disc, artist and track name.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CNP301) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CNP301
J-2502-076-1
SERVO BOARD
CN2
3
CDX-GT800D/GT805DX
SOLDER
• UNLEADED
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
4
TABLE OF CONTENTS
1.
GENERAL
Location of Controls ........................................................ 5
Connections ..................................................................... 6
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
2-10.
2-11.
2-12.
2-13.
Base Panel Assy ...............................................................
Sub Panel Assy ................................................................
CD Mechanism Block .....................................................
Driving Section (DB-F05) ...............................................
Follow Move (F) Assy, Driving (F) Assy ........................
Main Board ......................................................................
Chassis (T) Sub Assy .......................................................
Roller Arm Assy ..............................................................
Chassis (OP) Assy ...........................................................
Optical Pick-up ................................................................
SL Motor Assy (M902) ...................................................
LE Motor Assy (M903) ...................................................
Servo Board .....................................................................
3.
DIAGNOSIS FUNCTION ........................................ 17
4.
DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
4-9.
4-10.
4-11.
4-12.
4-13.
4-14.
4-15.
Block Diagram –CD Section– .........................................
Block Diagram –Main Section– ......................................
Block Diagram –Display Section– ..................................
Circuit Boards Location ..................................................
Printed Wiring Boards –CD Mechanism Section– ..........
Schematic Diagram –CD Mechanism Section (1/2)– .....
Schematic Diagram –CD Mechanism Section (2/2)– .....
Printed Wiring Boards –Main Section– ...........................
Schematic Diagram –Main Section (1/4)– ......................
Schematic Diagram –Main Section (2/4)– ......................
Schematic Diagram –Main Section (3/4)– ......................
Schematic Diagram –Main Section (4/4)– ......................
Printed Wiring Boards –Panel Section– ..........................
Printed Wiring Board –Display Section– ........................
Schematic Diagram –Display Section– ...........................
5.
EXPLODED VIEWS
5-1.
5-2.
5-3.
5-4.
5-5.
5-6.
5-7.
Main Section ....................................................................
Main Board Section .........................................................
Front Panel Section .........................................................
CD Mechanism Section (1) .............................................
CD Mechanism Section (2) .............................................
CD Mechanism Section (3) .............................................
CD Mechanism Section (4) .............................................
6.
ELECTRICAL PARTS LIST .................................. 53
10
10
11
11
12
12
13
13
14
14
15
15
16
19
20
21
22
23
24
25
26
28
29
30
31
32
33
34
46
47
48
49
50
51
52
CDX-GT800D/GT805DX
SECTION 1
GENERAL
This section is extracted
from instruction manual.
• LOCATION OF CONTROLS
• CDX-GT800D
Location of controls and basic operations
Main unit
1 2
3
4
5
6
7 8
ANGLE
OFF
PUSH SOUND
+
VOL
MENU
–
SOURCE
REP
1
SHUF
2
3
4 5
PAUSE
6
AF/TA
IMAGE
CDX-GT800D
9
q;
qa
Card remote commander
RM-X154
2
q;
7
OFF
SOURCE
SOUND
MENU
MODE
LIST
+
qh
ENTER
qj
A MODE button 8, 17
To select the radio band (FM/MW/LW)/
select the unit*1.
B OFF button
To power off/stop the source.
C VOL (volume) control dial/SOUND
button 16
To adjust volume (rotate); select sound items
(press).
–
qk
REP
1
wf
qa
SCRL
DSPL/PTY
SHUF
2
3
5
PAUSE
6
4
D Display window
E Disc slot 5
To insert the disc.
+
ql
qg
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
w;
wa
1
ws
wd
ATT
qs qd qf
F SEEK control dial/ENTER button
To select items (rotate); complete a setting
(press).
CD:
To skip tracks or album/groups: press
(ENTER) repeatedly to select ./> or
“ALBM/GROUP,” then rotate the SEEK
control dial until the desired track or album/
group appears.
Radio:
To tune in stations: press (ENTER)
repeatedly to select “SEEK,” “MANUAL,”
or “PRESET,” then rotate the SEEK control
dial until the desired station appears.
VOL
–
qk DSPL (display)/PTY (Programme
Type) button 8, 10
To change display items; to select PTY in
RDS.
I
ql VOL (volume) +/– button
To adjust volume.
(front panel release) button 4
J SOURCE button
To power on/change the source (Radio/CD/
MD*2/AUX).
PUSH ENTER
SEEK
MODE
H Z (eject)/ANGLE button 5
To eject the disc/slide down the front panel
(press); angle the front panel in 3 positions
(press and hold).
K Number buttons
Radio:
To receive stored stations (press); store
stations (press and hold).
CD/MD*2:
(1): REP 8, 18
(2): SHUF 8, 18
(6): PAUSE*3
To pause playback. To cancel, press again.
L RESET button 4
M AF (Alternative Frequencies)/TA
(Traffic Announcement) button 10
To set AF and TA/TP in RDS.
N Receptor
To receive signals from the card remote
commander.
O IMAGE button 2
To select the display image.
Movie mode 1-3 t Spectrum analyzer
mode 1-5 t Space Producer mode t Wall
paper mode 1-3 t normal play/reception
mode
w; ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
wa SOUND button
To select sound items.
ws LIST button 9, 18
To list up.
wd M/m (+/–) buttons
To select preset stations/skip groups (press);
skip groups continuously (press and hold).
wf SCRL (scroll) button 8
To scroll the display item.
*1 When a CD/MD changer is connected.
*2 When an MD changer is connected.
*3 When playing back on this unit.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 21.
The following buttons on the card remote
commander have also different buttons/functions
from the unit.
qh ENTER button
To complete a setting.
qj </, (SEEK –/+) buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
G MENU button
To enter menu.
6
7
• CDX-GT805DX
Location of controls and basic operations
Main unit
1 2
3
4
5
6
7 8
ANGLE
I
OFF
+
VOL
SEEK
MODE
MENU
–
SOURCE
REP
1
SHUF
2
3
4 5
PAUSE
6
DSPL
IMAGE
CDX-GT805DX
9
q;
qa
Card remote commander
RM-X152
2
q;
7
OFF
SOURCE
ATT
SOUND
MODE
LIST/
CAT
MENU
+
qh
ENTER
qj
qd
–
SCRL
DSPL
REP
1
4
qk
ql
w;
1
wa
ws
SHUF
2
3
5
PAUSE
6
+
VOL
–
wd
qa
qs qd qf
6
qg
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A MODE button 8, 15
To select the radio band (FM/AM)/select the
unit*1.
B OFF button
To power off/stop the source.
C VOL (volume) control dial/SOUND
button 14
To adjust volume (rotate); select sound items
(press).
D Display window
E Disc slot 5
To insert the disc.
F SEEK control dial/ENTER button
To select items (rotate); complete a setting
(press).
CD:
To skip tracks or album/groups: press
(ENTER) repeatedly to select ./> or
“ALBM/GROUP,” then rotate the SEEK
control dial until the desired track or album/
group appears.
Radio:
To tune in stations: press (ENTER)
repeatedly to select “SEEK,” “MANUAL,”
or “PRESET,” then rotate the SEEK control
dial until the desired station appears.
G MENU button
To enter menu.
(front panel release) button 4
J SOURCE button
To power on/change the source (Radio/CD/
MD*2/AUX/SAT*3).
PUSH ENTER
PUSH SOUND
H Z (eject)/ANGLE button 5
To eject the disc/slide down the front panel
(press); angle the front panel in 3 positions
(press and hold).
K Number buttons
Radio:
To receive stored stations (press); store
stations (press and hold).
CD/MD*2:
(1): REP 8, 16
(2): SHUF 8, 16
(6): PAUSE*4
To pause playback. To cancel, press again.
L RESET button 4
M DSPL (display) button 8
To change display items.
N Receptor
To receive signals from the card remote
commander.
O IMAGE button 2
To select the display image.
Movie mode 1-3 t Spectrum analyzer
mode 1-5 t Space Producer mode t Wall
paper mode 1-3 t normal play/reception
mode
ql ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
w; SOUND button
To select sound items.
wa LIST/CAT*3 button 9, 16
To list up.
ws M/m (+/–) buttons
To select preset stations/skip groups (press);
skip groups continuously (press and hold).
wd SCRL (scroll) button 8
To scroll the display item.
*1
*2
*3
*4
When a CD/MD changer is connected.
When an MD changer is connected.
When the SAT tuner is connected.
When playing back on this unit.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 19.
The following buttons on the card remote
commander have also different buttons/functions
from the unit.
qh ENTER button
To complete a setting.
qj </, (SEEK –/+) buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); fast-forward/
reverse a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
qk VOL (volume) +/– button
To adjust volume.
7
5
CDX-GT800D/GT805DX
• CONNECTIONS
• CDX-GT800D
• CDX-GT805DX
Connection example
A
Notes (2-A)
• Be sure to connect the ground lead before connecting the
amplifier.
• The alarm will only sound if the built-in amplifier is used.
AUDIO OUT
FRONT
SUB OUT (MONO)
Tip (2-B- )
For connecting two or more CD/MD changers, the source
selector XA-C30 (not supplied) is necessary.
Exemple de raccordement
AUDIO OUT
REAR
Remarques (2-A)
• Raccordez d’abord le câble de mise à la masse avant de
raccorder l’amplificateur.
• L’alarme est émise uniquement lorsque l’amplificateur intégré
est utilisé.
B
Conseil (2-B- )
Dans le cas du raccordement de deux changeurs de CD/MD ou
plus, le sélecteur de source XA-C30 (non fourni) est requis.
BUS AUDIO IN
Ejemplo de conexiones
Notas (2-A)
• Asegúrese de conectar primero el cable de conexión a masa
antes de realizar la conexión del amplificador.
• La alarma sonará únicamente si se utiliza el amplificador
incorporado.
BUS CONTROL IN
Sugerencia (2-B- )
Si desea conectar dos o más cambiadores de CD/MD,
necesitará el selector de fuente XA-C30 (no suministrado).
BUS AUDIO IN
Source selector*
Sélecteur de source*
Selector de fuente*
XA-C30
BUS CONTROL IN
* not supplied
non fourni
no suministrado
6
CDX-GT800D/GT805DX
• CDX-GT800D
7
CDX-GT800D/GT805DX
• CDX-GT805DX
*1
Source selector
(not supplied)
Sélecteur de source
(non fourni)
Selector de fuente
(no suministrado)
*4
*3
Supplied with the CD/MD changer
Fourni avec le changeur de CD/MD
Suministrado con el cambiador de CD/MD
XA-C30
*5
BUS AUDIO IN
/AUX IN*2
AUDIO OUT
FRONT
REMOTE
IN
*6
L
*1
SUB OUT (MONO)
from car antenna
à partir de l’antenne de la voiture
desde la antena del automóvil
3
Max. supply current 0.3 A
Courant max. fourni 0,3 A
Corriente máx. de alimentación de 0,3 A
Left
Gauche
Izquierdo
Right
Droit
Derecho
Left
Gauche
Izquierdo
Right
Droit
Derecho
BUS AUDIO AUDIO
AUDIO OUT
OUT
IN
REAR FRONT
AUDIO OUT
REAR
Fuse (10 A)
Fusible (10 A)
Fusible (10 A)
Blue/white striped
2
Rayé bleu/blanc
Con rayas azules y blancas
AMP REM
White
Blanc
Blanco
White/black striped
Rayé blanc/noir
Con rayas blancas y negras
Gray
Gris
Gris
Gray/black striped
Rayé gris/noir
Con rayas grises y negras
Green
Vert
Verde
Green/black striped
Rayé vert/noir
Con rayas verdes y negras
Purple
Mauve
Morado
Connection diagram
Schéma de raccordement
1 À un point métallique de la voiture
First connect the black ground lead, then connect the
orange/white striped, yellow, and red power input leads.
2 To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is no power
antenna or antenna booster, or with a manually-operated
telescopic antenna.
• When your car has a built-in FM/AM antenna in the rear/
side glass, see “Notes on the control and power supply
leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination signal
Be sure to connect the black ground lead to a metal surface
of the car first.
6 To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground lead to a metal
surface of the car first.
• When your car has a built-in FM/AM antenna in the rear/
side glass, see “Notes on the control and power supply
leads.”
7 To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground lead to a metal surface
of the car first.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V DC
when you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/side
glass, connect the power antenna control lead (blue) or the
accessory power input lead (red) to the power terminal of the
existing antenna booster. For details, consult your dealer.
• A power antenna without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground lead of this unit to the negative (–)
terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “Failure”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
BUS
CONTROL IN
Black
Noir
Negro
1
Blue
Bleu
Azul
Light blue
Bleu ciel
Azul celeste
ANT REM
2
Max. supply current 0.1 A
Courant max. fourni 0,1 A
Corriente máx. de alimentación de 0,1 A
Orange/white striped
Rayé orange/blanc
Con rayas naranjas y blancas
ATT
ILLUMINATION
Red
Rouge
Rojo
Yellow
Jaune
Amarillo
Purple/black striped
Rayé mauve/noir
Con rayas moradas y negras
1 To a metal surface of the car
Branchez d’abord le fil de masse noir et, ensuite, les fils
d’entrée d’alimentation rayé orange/blanc, jaune, et rouge.
2 Vers le câble de commande d’antenne
électrique ou le câble d’alimentation de
l’amplificateur d’antenne
Remarques
• Il n’est pas nécessaire de raccorder ce câble s’il n'y a pas
d’antenne électrique ou d’amplificateur d’antenne, ou avec
une antenne télescopique manuelle.
• Si votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, voir « Remarques
sur les câbles de commande et d’alimentation ».
3 Au niveau de AMP REMOTE IN de
l’amplificateur de puissance en option
Ce raccordement s’applique uniquement aux amplificateurs.
Le branchement de tout autre système risque
d’endommager l’appareil.
4 Vers le cordon de liaison d’un téléphone de
voiture
5 Vers le connecteur du signal d’éclairage de
la voiture
Raccordez d’abord le câble de mise à la masse noir à un
point métallique du véhicule.
6 À la borne +12 V qui est alimentée quand la
clé de contact est sur la position accessoires
Remarques
• S’il n’y a pas de position accessoires, raccordez la borne
d’alimentation (batterie) +12 V qui est alimentée en
permanence. Raccordez d’abord le câble de mise à la
masse noir à un point métallique du véhicule.
• Si votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, voir « Remarques
sur les câbles de commande et d’alimentation ».
7 À la borne +12 V qui est alimentée en
permanence
Raccordez d’abord le câble de mise à la masse noir à un
point métallique du véhicule.
Remarques sur les câbles de commande et d’alimentation
• Le câble de commande d’antenne électrique (bleu) fournit une
alimentation de + 12 V CC lorsque vous mettez la radio sous
tension.
• Lorsque votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, raccordez le câble de
commande d’antenne électrique (bleu) ou l’entrée d’alimentation
des accessoires (rouge) à la borne d’alimentation de
l’amplificateur d’antenne existant. Pour plus de détails, consultez
votre détaillant.
• Une antenne électrique sans boîtier de relais ne peut pas être
utilisée avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le câble d’entrée d’alimentation jaune est raccordé, le
circuit de la mémoire est alimenté en permanence même si la clé
de contact est sur la position d’arrêt.
Remarques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettez l’appareil hors
tension.
• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms
avec une capacité électrique adéquate pour éviter de les
endommager.
• Ne raccordez pas les bornes du système de haut-parleurs au
châssis de la voiture et ne raccordez pas les bornes des hautparleurs droit à celles du haut-parleur gauche.
• Ne raccordez pas le câble de mise à la masse de cet appareil
à la borne négative (–) du haut-parleur.
• N’essayez pas de raccorder les haut-parleurs en parallèle.
• Raccordez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avec amplificateurs intégrés)
aux bornes des haut-parleurs peut endommager l’appareil.
• Pour éviter tout dysfonctionnement, n’utilisez pas les câbles
des haut-parleurs intégrés installés dans votre voiture si
l’appareil partage un câble négatif commun (–) pour les hautparleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de
l’appareil.
Remarque sur le raccordement
Si les haut-parleurs et l’amplificateur ne sont pas raccordés
correctement, le message « Failure » s’affiche. Dans ce cas,
assurez-vous que les haut-parleurs et l’amplificateur sont bien
raccordés.
8
*1 RCA pin cord (not supplied)
*2 Be sure to match the color-coded cord
for audio to the appropriate jacks from
the unit. If you connect an optional
CD/MD changer, you cannot use AUX
IN terminal.
*3 Auxiliary optional equipment such as
portable DVD player (not supplied)
*4 Supplied with the auxiliary equipment
*5 Supplied with XA-C30
6
* Insert with the cord upwards.
R
Diagrama de conexión
1 A una superficie metálica del automóvil
Conecte primero el cable de puesta a masa negro, y
después los cables con rayas naranjas y blancas, amarillo, y
rojo de entrada de alimentación.
2 Al cable de control de la antena motorizada
o al cable de fuente de alimentación del
amplificador de señal de la antena
Notas
• Si no se dispone de antena motorizada ni de amplificador
de antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
• Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
3 A AMP REMOTE IN de un amplificador de
potencia opcional
Esta conexión es sólo para amplificadores. La conexión de
cualquier otro sistema puede dañar la unidad.
4 Al cable de interfaz de un teléfono para
automóvil
5 A una señal de iluminación del automóvil
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
6 Al terminal de alimentación de +12 V que
recibe energía en la posición de accesorio
del interruptor de la llave de encendido
Notas
• Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a
masa negro a una superficie metálica del automóvil.
• Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
7 Al terminal de alimentación de +12 V que
recibe energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de
alimentación
• El cable de control de la antena motorizada (azul) suministrará
cc de + 12 V cuando conecte la alimentación del sintonizador.
• Si el automóvil dispone de una antena de FM/AM incorporada
en el cristal trasero o lateral, conecte el cable de control de
antena motorizada (azul) o el cable de entrada de alimentación
auxiliar (rojo) al terminal de alimentación del amplificador de
antena existente. Para obtener más información, consulte a su
distribuidor.
• Con esta unidad no es posible utilizar una antena motorizada
sin caja de relé.
Conexión para protección de la memoria
Si conecta el cable de entrada de alimentación amarillo, el
circuito de la memoria recibirá siempre alimentación, aunque
apague la llave de encendido.
Notas sobre la conexión de los altavoces
• Antes de conectar los altavoces, desconecte la alimentación
de la unidad.
• Utilice altavoces con una impedancia de 4 a 8 Ω con la
capacidad de potencia adecuada para evitar que se dañen.
• No conecte los terminales de altavoz al chasis del automóvil,
ni conecte los terminales del altavoz derecho con los del
izquierdo.
• No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
• No intente conectar los altavoces en paralelo.
• Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplificadores incorporados) a los terminales de
altavoz, puede dañar la unidad.
• Para evitar fallos de funcionamiento, no utilice los cables de
altavoz incorporados instalados en el automóvil si su unidad
comparte un cable negativo común (–) para los altavoces
derecho e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz y el amplificador no están conectados
correctamente, aparecerá “Failure” en la pantalla. Si es así,
compruebe la conexión de ambos dispositivos.
4
5
6
7
*1 Cordon à broche RCA (non fourni)
*2 Veillez à faire correspondre le code de
couleur du cordon audio à celui des
fiches correspondantes de l’appareil.
Si vous raccordez un changeur de
CD/MD en option, vous ne pouvez
pas utiliser la borne AUX IN.
*3 Appareil auxiliaire en option, par
exemple un lecteur de DVD portable
(non fourni)
*4 Fourni avec l’appareil auxiliaire
*5 Fourni avec le XA-C30
*6 Insérez avec le câble vers le haut.
*1 Cable con terminales RCA
(no suministrado)
*2 Asegúrese de hacer coincidir el cable
de audio codificado con colores con
las tomas correspondientes de la
unidad. Si conecta un cambiador de
CD/MD opcional, no podrá utilizar el
terminal AUX IN.
*3 Equipo opcional auxiliar como
un reproductor de DVD portátil
(no suministrado)
*4 Suministrado con el equipo auxiliar
*5 Suministrado con el XA-C30
*6 Insertar con el cable hacia arriba.
CDX-GT800D/GT805DX
SECTION 2
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
SET
2-1.
BASE PANEL ASSY
(Page 10)
2-2.
SUB PANEL ASSY
(Page 10)
2-3.
CD MECHANISM BLOCK
(Page 11)
2-4.
DRIVING SECTION
(DB-F05)
(Page 11)
2-7.
CHASSIS (T) SUB ASSY
(Page 13)
2-5.
FOLLOW MOVE (F) ASSY,
DRIVING (F) ASSY
(Page 12)
2-8.
ROLLER ARM ASSY
(Page 13)
2-6.
MAIN BOARD
(Page 12)
2-9.
CHASSIS (OP) ASSY
(Page 14)
2-10. OPTICAL PICK-UP
(Page 14)
2-11. SL MOTOR ASSY (M902)
(Page 15)
2-13. SERVO BOARD
(Page 16)
2-12. LE MOTOR ASSY (M903)
(Page 15)
9
CDX-GT800D/GT805DX
Note: Follow the disassembly procedure in the numerical order given.
2-1. BASE PANEL ASSY
2 two screws
(panel F)
5 bracket (PWB)
7 base panel assy
1 two screws
(panel F)
8 FLEXIBLE board (27 core)
(CN607)
(Take care not to pull the
flexible board excessively)
4 two screws (T)
3
6 BASE PANEL board
2-2. SUB PANEL ASSY
3 two claws
6 SUB PANEL board
2 two claws
5 claw
1 two screws
(+PTT 2.6 × 6)
4
7 sub panel assy
10
CDX-GT800D/GT805DX
2-3. CD MECHANISM BLOCK
5 CD mechanism block
6 two screws
(+PTT 2.6 × 6)
7 bracket (CD)
2 screw
(+PTT 2.6 × 6)
3
4 CNP301
1 screw
(+PTT 2.6 × 6)
2-4. DRIVING SECTION (DB-F05)
3 screw
(+PTT 2.6 × 6)
4 driving section
(DB-F05)
1 CN702 (7P)
2 screw
(+PTT 2.6 × 6)
11
CDX-GT800D/GT805DX
2-5. FOLLOW MOVE (F) ASSY, DRIVING (F) ASSY
To install the assembly, turn the gear (cam LF5) and
align the detent with the holes A.
gear (cam LF5)
6 joint
A
2 follow move (F) assy
5 driving (F) assy
gear (cam RF5)
1 screw
(M 2.6 × 6)
4 screw
(M 2.6 × 6)
3 drive shaft assy
B
To install the assembly,
turn the gear (cam RF5) and align
the detent with the holes B.
2-6. MAIN BOARD
2 two screws
(+PTT 2.6 × 8) 5 screw
(+PTT 2.6 × 8)
1 three ground point screws
(+PTT 2.6 × 6)
7 cord (sub out (MONO))
6 CN401 (3P)
4 MAIN board
3 insulating sheet
12
CDX-GT800D/GT805DX
2-7. CHASSIS (T) SUB ASSY
4 claw
2 two screws
(+P 1.7 × 2.2)
1 two screws
(+P 1.7 × 2.2)
6 chassis (T) sub assy
5 SENSOR board
3 claw
2-8. ROLLER ARM ASSY
3 washer
5 roller arm assy
4 gear (RA1)
2 spring (RAR-B)
1 spring (RAL-B)
13
CDX-GT800D/GT805DX
2-9. CHASSIS (OP) ASSSY
8
qa chassis (OP) assy
0 coil spring (damper)
lever (D)
4 washer
6
1 optical pick-up (16 core)
(CN1)
9 two coil springs (damper)
5 gear (LE1)
7
slider (R)
3 tension coil spring (KF60)
2 Remove the six solders.
2-10. OPTICAL PICK-UP
2 chucking arm sub assy
5 claw
1 tension coil spring (CHKG)
7 optical pick-up
6 main shaft
4 rack (SL)
3 screw
(+B 1.4 × 5)
14
CDX-GT800D/GT805DX
2-11. SL MOTOR ASSY (M902)
1 screw
(+P 1.4 × 1.8)
2 SL motor assy (M902)
2-12. LE MOTOR ASSY (M903)
0 gear (LE) assy
8 screw
(+M 1.7 × 2.5)
9 bearing (LEB-N)
qf two toothed lock screws
(+M 1.4 )
qa screw
(+M 1.7 × 2.5)
2 washer
3 gear (LE1)
lever (D)
4
bracket (LEM-N)
qs screw
(+M 1.7 × 2.5)
qd
qg LE motor assy
(M903)
5
6 screw
(+P 1.7 × 2.2)
slider (R)
7 leaf spring (LE)
1 Remove the two solders.
15
CDX-GT800D/GT805DX
2-13. SERVO BOARD
1 Remove the eight solders.
6 SERVO board
2 Remove the three solders.
4 screw
5 claw
3 optical pick-up (16 core)
(CN1)
16
CDX-GT800D/GT805DX
SECTION 3
DIAGNOSIS FUNCTION
Description of the Diagnostics function:
4. Contents of each display mode
4-1. Reset count display mode
1. Setting the Diag display mode
With the power off, press the [4] button, [5] button, and [4] button
on the set body or the remote control (for more than 2 seconds)
in turn.
2. Canceling the Diag display mode
During the Diag function mode, press the [OFF] button.
3. Initial display in the Diag display mode.
Just when the Diag mode is entered, “reset count” is displayed.
The display mode is switched by each rotation of SEEK + >
/ . SEEK --- dial.
DIAG
01
XX
Reset count
(in hexadecimal format)
Diag code
01: Reset count
4-2. Reset count by watchdog timer display mode
DIAG
02
XX
Reset count
(in hexadecimal format)
Reset count display
DIAG
01
Diag code
02: Number of resets by watchdog timer
XX
4-3. Number of connected units display mode
Reset count by watchdog timer display
DIAG
02
Y
XXX
XX
Number of connected units display
DIAG
03
DIAG
03
1
XXX
Show the number of connected units for
CD-C, MD-C and XM respectively from
the rightmost (in hexadecimal format).
Recency of information
1-3: 1 represents the latest.
Diag code
03: Number of connected unit.
Operating hours display
DIAG
04
XXXX
The display mode is switched by push of [PUSH ENTER] button
during the number of connected units display mode.
.
CD error information display
No. of connected units history 1 (latest) display
DIAG
05
1
DIAG
XX
03
OFFSET/FAILURE error display
1
No. of connected units history 2 display
DIAG
06
XXX
DIAG
1XXXXX
03
2
XXX
No. of connected units history 3 display
DIAG
03
3
XXX
4-4. Operating hours display mode
DIAG
04
XXXX
Operating hours
(in hexadecimal format)
Diag code
04: Operating hours
17
CDX-GT800D/GT805DX
4-5. CD error information display mode
4-5-1. Error description
4-6. OFFSET/FAILURE error display mode
DIAG
06
DIAG
05
Y
YXXXXX
XX
Error information
Error description Indication
Description
(in hexadecimal
1X
SERVO ERROR
format)
3X
LOADING ERROR
Recency of information
4X
TRACK JUMP
1-3: 1 represents the latest.
5X
TEXT ERROR
Diag code
FX
MECHA
ERROR
05: CD error information
Operating hours
Error description
(0: OFFSET, 1: FAILURE)
Recency of information
1-3: 1 represents the latest.
Diag code
06: OFFSET/FAILURE
The display mode is switched by push of [PUSH ENTER] button
during the OFFSET/FAILURE error display mode.
4-5-2. Disc type and operating hours
DIAG
05
YXXXXX
OFFSET/FAILURE error history 1 (latest) display
Disc type
Operating hours
Disc type
Recency of information
1-3: 1 represents the latest.
Diag code
05: CD error information
Indication
0
1
2
3
8
F
Disc type
MP3
WMA
AAC
ATRAC
CD/DA
UNKNOWN
The display mode is switched by push of [PUSH ENTER] button
during the CD error information display mode.
DIAG
06
OFFSET/FAILURE error history 2 display
DIAG
06
DIAG
05
1
XX
CD error info history 1 (latest)
Disc type plus operating hours display
DIAG
05
1XXXXX
CD error info history 2
Error description plus error details display
DIAG
05
2
XX
CD error info history 2
Disc type plus operating hours display
DIAG
05
2XXXXX
CD error info history 3
Error description plus error details display
DIAG
05
3
XX
CD error info history 3
Disc type plus operating hours display
DIAG
05
18
3XXXXX
2XXXXX
OFFSET/FAILURE error history 3 display
DIAG
06
CD error info history 1 (latest)
Error description plus error details display
1XXXXX
3XXXXX
CDX-GT800D/GT805DX
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM — CD SECTION —
D/A, A/D CONVERTER
IC801
LPF
IC471
DETECTOR
PD2
PD2
PD1
96 FPI2
PD1
88 AGCI RFEQO 83
RFO 89
81 RFI
82 RFRPI
94 FNI2
AOUT1 (P07) 62
BCK (P08) 63
LRCK (P09) 64
22 SDIN0
27 BCLK0
26 LRCLK0
97 FPI1
I-V AMP
95 FNI1
E
E
F
F
VC
LASER DIODE
RFRP 3
2 RFZI
98 TPI
TEI 6
7 TEZI
LD
R-CH
7
FL
3
1
RL
MAIN
SECTION
A
VOUT3 60
+3.3V
+1.7V REG.
Q801
VINL1 72
VINR1 73
47 DVDD
40 DVDD
SUB
A-L
R-CH
30 VDRIVE
<VRO>
AUTOMATIC
POWER
CONTROL
Q21
91 LDO
MDI 92
PIO3
PIO0
MSTBY
ZDET
/RST
/CCE
BUCK(CLK)
BUS3(SI)
BUS2(SO)
BUS1
BUS0
MON OUT
OPTICAL
PICK-UP BLOCK
(KSS1000E)
2-AXIS DEVICE
VOUT1 58
VOUT2 59
5
(Page 20)
RF AMP,DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR
IC2
100 TNI
84
33 MLCKI
R-CH
VC
LD
PD
X801
11.2896MHz
AUXL1 56
AUXR1 57
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING
MOTOR DRIVE
IC1
FCS+
FCS–
16 VO4–
OPIN4+ 27
OPIN4– 26
15 VO4+
OPOUT4 25
18 VO3–
OPIN3+ 24
OPIN3– 23
17 VO3+
OPOUT3 22
37
30
27
15
14
13
12
11
10
8
7
51
48
36
58
37
43
42
41
40
39
38
XI 23
VC
81 X1
X2
16.934MHz
9 F0O
DEC_XMUTE
DEC_INT
DEC_SSTBY
CD_ZDET
CD_XRST
CD_XCCE
CD_BUCK
CD_BUS3
CD_BUS2
CD_BUS1
CD_BUS0
SYSTEM CONTROL
IC303 (1/3)
XFLASH & EJECT_OK 61
XO 24
80 X0
(FOCUS)
(TRACKING)
TRK+
TRK–
SW1
(DOWN)
10 TRO
SW2
(SELF)
M902
(SLED)
M
14 VO1+
OPOUT1 4
12 FMO
13 VO1–
OPOUT2 7
13 DMO
SW3
(DISC IN)
46 MEC_DSW
53 MEC_SELFSW
45 MEC_INSW
48 CDM_ON
49 CD_ON
50 Z_DET
MECON 63
CDON 64
ZMUTE 66
CD
SYSTEM CONTROL
IC3
X1
12MHz
47 EJECT_OK
UNISI
RXD
UNISO
TXD
UNICKI
BUS_ON
BU_IN
RSTX
A_ATT
LINKOFF
UNI SI
56
25
57
26
58
50
51
75
60
59
UNI SO
UNI CLK
BUS ON
BU CHK
SYS RST
ATT
LINK ON/OFF
MECON_CHK 67
M
12 VO2+
(Page 20)
CD+6V
CDON_CHK 68
CD+3.3V
BIAS 20
M901
(SPINDLE)
MAIN
SECTION
B
+1.5V REG
IC6
SW4
(LIMIT)
MUTE 21
11 VO2–
42 MEC_LIMIT
+1.5V ON/OFF
SWITCH
Q2,3
+1.5V
5 VOUT
VDD 1
CE 3
BU+3.3V
6 DRVON
M903
(LOADING)
M
10 VOL+
9 VOL–
FWD 1
+1.5V
LOAD
43 MEC LOAD
REV 28
CDON_1500MV 1
1.5V_ON
44 MEC EJECT
+3.3V
SWITCHING
DRIVER
Q651,652
• R-ch is omitted due to same as L-ch.
• Signal Path
: CD PLAY
: FM/MW/LW
CDX-GT800D/GT805DX
19
19
BATT
4
OUT
1 IN
VCC 5
+3.3V SWITCHING
REG.
IC650
BATT1
CDX-GT800D/GT805DX
4-2. BLOCK DIAGRAM — MAIN SECTION —
IN/OUT SELECT,
ELECTRIC VOLUME
IC401
FL
R-CH
CD
SECTION
RL
A
R-CH
(Page 19)
SUB
A-L
R-CH
10
L
8
R-CH
PJ401(1/2)
(BUS AUDIO IN)
R
GROUND
SWITCH
Q408
R-CH
12
14
1
3
6
3
5
4
2
AUX-L-IN
AUX-R-IN
AUX-L-GND
AUX-R-GND
FIL
PRE AMP
IC402
PJ401(2/2)
FL-OUT 36
5 RL+
OUT(RL) 3
L
MUTE
Q181
RL-OUT 37
17 FL+
L
OUT(FL) 19
SUB-OUT 35
3
AUDIO+8.3V
TU+5V
BU+3.3V
GT800D
E_VOL_MUTE/RX
E_VOL_CKO
E_VOL_SO/TX
BUS/AUX
12 IN-FL
D904
RDS DEMODULATOR
IC551
RDS 9
SCL 11
SDA 12
16 MPX
D906
RDS
+3.3V
RDS B+
SWITCH
Q551,552
BU+3.3V
22 STB
25 DIAG
16 AC GND
VDDD
7
18 TUNER ATT-IN
82 QUALITY
NS MASK
SWITCH
Q380
83 VSM
21 TUNER ATT
E2P_SCL 16
E2P_SDA 17
23 EECKO (TU)
22 EESIO (TU)
7
+9V REG
IC703
1
: BUS AUDIO/AUX
BATT
2 VIN
3
4
UNI_SO 3
64 MOT+ # NC
65 MOT- # NC
B+ SWITCH B+
Q702,703
ILL
13
ATT
TEST
D104
B CHK
BATT
RESET
BUS ON
CLK
CLK IN
DATA OUT DATA I/O
DATA IN
BUS ON
OVER VOLTAGE
DETECT
Q101
3
D105
BATT
8
4
6
4
5
6
BUS ON
SWITCH
Q110,111,112
1
3
2
1
CNP102
(BUS CONTROL IN)
7
BATT
TH100
RST 2
LINK OFF
ATT
79 FP-IDET # NC
ON/OFF
1
B_UP+5V
ACC
6
I-DET
IC701
V OUT 4
7
D128
MOTOR
DRIVE
IC702
10
13
12
11
8
9
BATT
B_UP+5V
CD+3.3V
CD+6V
ILL+B
15
58
56
57
5
4
AMP-R
ANT-R
14
BUS INTERFACE
IC110
M904
(OPEN/CLOSE)
16
FR+
FR–
RR+
RR–
AUDIO+8.3V
TESET_IN 54
BU_IN
SYSRESET
BUS_ON
UNI_CKO
UNI_SI
RL+
RL–
BATT
TEL ATTENATION SWITCH
Q103
19 NS-MASK
S_METER 6
TU_MUTE 7
: AM/MW/LW
30
37
31
33
34
F901
ILLUMINATION CHECK
Q907
TEL_ATT 53
MUTE CONDITION 8
QUALITY 5
: FM
REG1 (AUDIO+B)
REG2 (BU5V)
REG3 (SERVO)
REG4 (DR+B)
REG5 (ILL)
D121
ACC CHECK
Q102
ILL_IN 51
RDS+3.3V
9
29
27
20
6
35
ACC_IN 52
VDDA
1
• R-CH is omitted due to same as L-CH.
• Signal Path
D120
SW1 (AMP_REM)
SW2 (ANT_REM)
VP1
VP2
VP (REG)
17 DAVN
INTN 15
10 XTO
12
3
11
5
6
R-CH
2 SDA
4 SCL
9 XTI
X551
8.664MHz
TU+5V
TU+5V REG
Q501
AUDIO+8.3V
BU+3.3V
+3.3V REG
IC301
B_UP+5V
BU CHK
SYS RST
SWITCH
BOARD
P-SENSOR
DETECT
Q701
63 MOTOR ON # NC
BUS ON
UNI CLK
68 P-SNSR # NC
UNI SI
UNI SO
67 OPEN_SW # NC
66 CLOSE_SW # NC
D301
RESET
STBY
B
CD
SECTION
(Page 19)
C
DISPLAY
SECTION
(Page 21)
CDX-GT800D/GT805DX
20
20
SUB OUT
(MONO)
4
ATT 25
AMP_STB 41
AMP_DIAG 40
BEEP 20
SCL
SDA
10
BATT
GT800D
SCL
SDA
2
OUT-RL+ 9
OUT-RL– 7
D401
SDA
SCL
I2C_CKO 27
I2C_SIO 28
AUDIO OUT
FRONT
CNP101
1
FL+
9
FL–
OUT-FL+ 5
OUT-FL– 3
11 IN-RL
R-CH (FRONT)
R-CH (REAR)
SYSTEM CONTROL
IC303 (2/3)
30
31
29
26
R
POWER AMP/
MULTIPLE VOLTAGE REGULATOR
IC201
MUTE CONTROL
Q401,402
SCL
SDA
TU_SCL 13
TU_SDA 14
L
MUTE
Q470
43 DATA
42 CLK
41 MUTE
AUDIO OUT
REAR
CN401
1
10 TU-L
9 TU-R
VCC 10
TU_VDD 11
E2P_VDD 15
R
R-CH
MUTE
Q171
FR-OUT 38
RR-OUT 39
R
R-CH
LINE AMP
IC470
L 4
R 3
1 ANT
FL-IN
FR-IN
RL-IN
RR-IN
SUB1
L-OUT
R-OUT
AMP
IC474
TUX501
(TUNER UNIT)
PJ501
(ANTENNA)
30
32
31
33
16
14
13
CDX-GT800D/GT805DX
4-3. BLOCK DIAGRAM — DISPLAY SECTION —
FL DISPLAY DRIVE
IC901
SYSTEM CONTROL
IC303 (3/3)
RE_1A # NC
RE_1B # NC
RE_2A # NC
RE_2B # NC DISP_CE
DISP SI/RX
DISP SO/TX
DISP CKO
84 KEY_IN0
76
75
78
77
ROTARY
ENCODER
S906(1/2),911(1/2)
KEY MATRIX
S903–905,
906(2/2),907–910,
LSW901(2/2)
–906(2/2), 911(1/2)
LAT_TA2_OUT 24
93
98
99
100
1
29
30
31
12 LAT
FL_DAT1 33
FL_DAT2 99
FL_DAT3 3
FL_CLK 35
FL_CLK_IN 5
FL_CLK_IN 100
SYS_CE
SYS_SO
SYS_SI
6
5
4
7
FL900
FLUORESCENT
INDICATOR
TUBE
SYS_CLK
11 GCP
13 BK
GCP_TA0_OUT 28
GCP_TA3_OUT 22
GCP_TA4_IN 19
85 KEY_IN1
DISP_RESET 90
88 KEY_ACK0
89 KEY_ACK1
87 KEY_ACK2
10 RESET
XOUT 11
X901
6.75MHz
XIN 13
DOOR_IND 95
Q303
RESET
IC302
LED901–915,
LSW901(1/2)
–906(1/2)
ILL+10V
RESET
IC904
1
55 RC_IN1
86 RC_IN0
CNJ101
(REMOTE IN)
SI1
SI2
SI3
CLK
LED990
(DISC IN)
LED DRIVE
Q134
LED990
D907
BU+3.3V
2 IN
OUT 1
10 RESET
S902
RESET
D303
S901
(FRONT PANEL DETECT)
NOSE_SW 91
RESET
XOUT 11
MAIN
SECTION
C
XIN 13
(Page 20)
BATT1
X302
6MHz
BATT
T620
DC-DC
CONVERTER
TRANSFORMER
STBY
X301
32.768kHz
REMOTE
CONTROL
SIGNAL
RECEIVER
IC903
OUT 2
9 XCOUT
8 XCIN
1 SIRCS
FSW OUT 73
TH301
80 TEMP-TR # NC
5
VCC
DC-DC
CONVERTER
CONTROL
Q621,622
7 CT
DC-DC
CONVERTER
IC620
OUT 4
POWER
CONTROL
Q623,Q642
FL+1V
SWITCHING
DRIVE
Q620
IN 1
Q624
EEPROM
IC802
FSW-IN 2
36 EESIO (DSP)
35 EECKO (DSP)
BU+3.3V
FL B+
SWITCH
Q301,302
FLD_ON
FLD ON 74
CDX-GT800D/GT805DX
21
21
FL+4.3V
D620,621
FL_ON 72
SDA 5
SCL 6
D623,624
FL+3.3V
FL+55V
D622
CDX-GT800D/GT805DX
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-4. CIRCUIT BOARDS LOCATION
SENSOR board
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
SERVO board
For schematic diagrams.
For printed wiring boards.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f
: internal component.
• C : panel designation.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
a
: Through hole.
•
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
tuner unit
(TUX501)
•
•
•
•
MAIN board
DISPLAY board
SUB PANEL board
BASE PANEL board
•
•
•
• Waveforms
•
— SERVO Board —
(CD PLAY)
1
4
IC2 5 (FEI)
7
IC2 ia (RFI)
IC3 ia (X1)
Approx.
1Vp-p
0V
•
•
A : B+ Line.
B : B– Line.
H : adjustment for repair.
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
CD mechanism section (1/2), (2/2)
no mark : CD PLAY
Main (1/4), (2/4), (3/4), (4/4) and Display sections
no mark : FM/MW/LW
<
> : CD PLAY
∗ : Impossible to measure
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
Circled numbers refer to waveforms.
Signal path.
J : CD PLAY
F : FM
f : MW/LW
L : BUS AUDIO
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
C
Q
These are omitted
B E
BE C
These are omitted
ECB
These are omitted
• Abbreviation
CH
: Chinese model.
1.1 Vp-p
Approx. 100 mVp-p
12 MHz
50 mV/DIV, 5 msec/DIV
0.5 V/DIV, 0.5 µsec/DIV
2
5
IC2 6 (TEI)
0.5 V/DIV, 0.2 µsec/DIV
— MAIN Board —
1
IC2 of (FNI2), og (FNI1)
0V
3
IC551 0 (XT0)
Approx. 400 mVp-p
IC303 qa (XOUT)
10 Vp-p
2.1 Vp-p
1.5 Vp-p
5
IC650 4 (OUT)
3.6 Vp-p
6 MHz
8.664 MHz
3 µsec
200 mV/DIV, 5 msec/DIV
0.5 V/DIV, 0.5 µsec/DIV
3
6
IC2 wd (XI)
IC2 oh (FPI2), oj (FPI1)
0.6 Vp-p
1
IC901 qa (XOUT)
1 V/DIV, 50 nsec/DIV
5 V/div, 1 µsec/div
1 V/DIV, 50 nsec/DIV
2
4
6
11.2896 MHz
1 V/div, 50 nsec/div
1 V/div, 50 nsec/div
CDX-GT800D/GT805DX
22
IC303 9 (XCOUT)
22
IC620 4 (OUT)
11 Vp-p
2.7 Vp-p
3.2 Vp-p
6.747 kHz
0.5 V/DIV, 0.5 µsec/DIV
IC801 ed (MCLKI)
3.0 Vp-p
1.5 Vp-p
16.9344 MHz
0.2 V/DIV, 0.2 µsec/DIV
— DISPLAY Board —
32.768 kHz
1 V/div, 10 µsec/div
2.97 µsec
5 V/div, 1 µsec/div
CDX-GT800D/GT805DX
4-5. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 22 for Circuit Boards Location.
2
1
3
4
5
6
: Uses unleaded solder.
7
8
9
10
11
12
13
14
A
C45
IC2
CN2
TP82
R6
R5
TP9
R2
TP85
TP99
R65
FMB4
R70
TP65
R72
R83
TP98
TP84
TP83
TP1
R74
TP3
R84
TP97
TP2
R18
R38
R39
R40
R41
R68
FMB5
TP7
R145
FB2
R97
R75
TP76
SW2
TP75
TP81
R143
TP14
TP13
1-689-230-
TP4
TP5
TP15
TP12
R9
CNP301
TP86
TP8
(Page 27)
IC1
BP10
TP10
R1
TP11
FMA3
TP87
G
TP79
TP80
TP6
R71
SW3
R73
TP78
R142
C10
TP69
R80
R88
C69
FB3
TP77
TP91
TP92
R87
TP70
R98
R96
FMA5
R86
R78
R79
R81
R82
C67
C66
F
X1
TP90
C62
TP62
TP74
TP89
TP61
R67
TP71
1
TP68
TP67
BP60
TP88
75
C68
R85
TP63
R69
R21
R64
TP28
C12 R11
C11
CN
C70
C40
TP52
TP32
C43
R63
TP95
R42
TP64
C42
TP50
TP72
TP51
16
76
TP33
C41
R37
R60
R62
R61
TP25
TP21
TP37
50
TP31
R29
R19
C39
50
R8
R36
C58
C60
TP22
1
R54
R53
TP36
TP35
TP34
51
26
FMA4
R35
100
R77
75
R52
C33 R28
C26
X2
FB4
C36
TP49
26
51
76
25
R30
C71
IC6
C47
R32
R31
R20
TP96
R27
R25
R26
R34
R24
Q2
R23
C20
C22
R15
C32
C72
R33
C133
R132
TP53
IC3
E
TP44
TP27
TP46
C49
TP42
C23
C25
TP43
TP45
100
C50
C53
C19
1
R22
R133
C80 C132
TP29
C13
C29
TP48
TP47
Q3
R13
R14
C31
C30
R48
R47
R46
25
D
C54
C24
C16
R55
R44
C15
R43
C
C55
C56
C48
C46
B
C14
C18
TP23
R12
R57
C52
Q21
R58
TP39 TP38
C44
FMA6
TP41
FMB3
C51
TP30
C17
R16
TP26 TP24
SW1
C7
1-866-806-
H
1-866-806-
• Semiconductor
Location
CDX-GT800D/GT805DX
23
23
Ref. No.
IC1
IC2
IC3
IC6
Location
G-2
B-11
D-2
D-1
Q2
Q3
Q21
C-1
C-2
B-4
CDX-GT800D/GT805DX
4-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 22 for Waveforms.
C18
C46
R55
R43
R48
C45
R47
R46
C15
R54
R52
R44
TP37
TP36
TP35
C47
R53
C44
TP34
R57
TP33
TP32
C49
C48
R18
TP31
C50
C51
TP52
TP38
IC6
R42
C52
C80
R22
TP39
C53
R23
TP53
R58
C54
C55
C56
IC2
R41
R24
R40
R25
R39
R26
R38
R27
Q2
R132
C132
C43
C24
R133
TP41
C19
CN1
C133
C42
C60
C41
C72
TP50
R29 R19
C11
R12
R37
TP51
TP21
TP22
R30
TP23
TP24
TP25
C40
C16
C58
R36
TP49
R13
R35
R11
C39
TP26
R33
TP27
C32
TP44
TP42
TP43
R31
C22
C20
TP28
C33
R20
C12
R32
C29
C36
R28
FB3
R34
C25
C13
C26
TP47
TP48
TP45
C30
C31
TP46
X2
C10
C23
Q21
TP29
R14
TP30
R15
FB2
C14
FB4
R16
C17
(Page 25)
CDX-GT800D/GT805DX
24
24
Q3
CDX-GT800D/GT805DX
• Refer to page 22 for Waveform.
• Refer to page 36 for IC Block Diagram.
4-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 41 for IC Pin Descriptions.
(Page 24)
(Page 30)
R97
TP88
TP81
R145
TP82
R143
TP83
TP97
TP84
TP98
TP85
TP99
TP70
TP69
C67
C66
R75
R78
R98
R142
R85
R79
TP79
TP80
C68
R87
R80
TP92
R82
TP91
TP78
R81
TP90
TP77
R77
R83
TP76
R86
TP67
TP89
R84
TP75
TP68
CN2
TP74
C69
R74
TP86
X1
TP87
R73
R72
R96
C70
R71
R88
TP1
SW4
TP2
IC B/D
IC3
TP65
R70
TP64
C62
TP72
TP3
SW3
R5
R1
TP4
SW2
R8
BP60
TP5
R6
TP71
TP63 R69
R9
IC1
SW1
TP62
R2
R68
C7
TP10
TP61
BP10
R67
TP6
TP8
M902
TP9
CDX-GT800D/GT805DX
25
25
R65
TP15
M901
C71
R63
TP13
R64
TP14
R62
TP7
R61
TP12
R60
TP11
R21
M903
CDX-GT800D/GT805DX
4-8. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 22 for Circuit Boards Location.
14
13
12
11
10
: Uses unleaded solder.
9
8
7
6
5
4
3
2
1
A
• Semiconductor Location
C209
R424
C206
C236 Q171
C218
C219
Q281
C238
R201
R433
C867
R429
R430
R382
IC470
R471
C469
C477
R473
C473
R498
R404
C408
C409
R405
R487
Q501
G
D829
C431
C554
C555
C556
C553
R556
IC551
Q134
R557
I
R265
Q303
RED
R348
CN606
H
C561
R555
JR603
FB551
R554
R845
D832
D833
C512
C557
D831
D814
C342
C552
C558 R553
R552
R551
FB552
R367
Q551
Q552
D835
1
100
C332
R621
R318
R319
R411
GT800D
IC302
R620
BLK
JR605
Q302
JR604
JR606
G1
1-869-016-
B
D
BASE PANEL BOARD
CN607
SUB PANEL BOARD
(Page 32)
CDX-GT800D/GT805DX
26
26
F
IC474
R408
R406
C327
R309
GT800D
D303
Q301
D501
C501
C412
R409
C313
L304
R501
C411
C317
R342
R345
R377
R410
C850
40
R853
R858
R462
R403
R310
R307 R311 25
26
R306
R364
L502
R336
R302
R344
R351
R347
R315
D630
R461
R488
D907
JR613
R637 R636
R304
C625
D626
JR607
R333
D322
R305
R633
R630 R631
R484
IC471
IC301
R334
R357 R350
R332
R356
D625
R340
R339 R341 75
R338
76
D304
5
IC620
4
IC303
GT805DX MODEL R327 R328
Q623
R360
R363
L620
8
R632
Q622
R625
JR608
R629
Q642
C626
Q621
IC650
Q624
C328
L303
R343
C653
R628
C331
R337
D653
R323 R322
51
R373
C478
R477
C822
R381
R663
R599
L401
R485
R475
R479
R481
X801
E
R483
C886
R303
R702
R856
IC472
R420
C471
R861
IC802
R372
50
R366
R346
R325 R365
R656
C654
R857
R869
C881
C851
R863
R862
D301
D703
C853
C858
R868
Q701
30
20
21
L652
Q380
R474
R478
R480
R476
C882
41 R860
R854
R855
C709
R706
C708
R709
50
10
IC702
C703
IC801
GT800D
FB502
C482
70
60
C820
C884
C883
R127
C111
G3
L503
C475
61
R802
R801
R811
1
1
C868
80 R859
C866
D
IC402
JR609
C470
R470
C474
C476
R472
C472
R126
C110
R707
R407
R431
C802
R812
1
R929
R922
JR618
Q112
R851
Q907
FB402
C418
R115
R119
R114
R117
5
IC703
R118
Q111
IC110
C701
R708
R432
C438
R435
L301
R402
C417
R111
D909
D105 R102
R101
D104
R434
Q103
R436
C707
R703
IC701
C442
C439
Q101
C704
C702
Q470
C436
C201
R109
Q110
C
Q181
R202
C202
C231
R112 R110
D108
R205
C216
C239
D120
D121
D401
D101
D115
R401
D117
C217
C208
Q271 R203
R204
C207
C237
D118
D103
D119
D102
R116
D111
C112
D110
D-11
D-8
E-10
E-10
E-10
I-4
C-4
C-3
C-4
C-3
J-7
J-7
I-5
E-2
D-3
G-2
H-4
H-4
H-10
H-10
H-9
H-10
H-9
G-10
E-9
R206
D114
D116
R103
C107
D106
R207
Q101
Q103
Q110
Q111
Q112
Q134
Q171
Q181
Q271
Q281
Q301
Q302
Q303
Q380
Q470
Q501
Q551
Q552
Q621
Q622
Q623
Q624
Q642
Q701
Q907
B
D113
Location
H-7
D-4
E-3
F-4
E-4
G-4
I-3
H-10
H-9
F-11
F-11
E-11
E-7
G-7
R659
R662
R660
E-10
G-6
H-6
Ref. No.
IC303
IC402
IC470
IC471
IC472
IC474
IC551
IC620
IC650
IC701
IC702
IC703
IC801
IC802
L651
IC110
IC301
IC302
Location
C-10
C-10
C-10
D-11
D-10
C-9
D-9
C-7
C-7
C-8
C-9
C-9
C-9
C-9
C-6
C-6
C-6
C-6
F-9
I-5
H-8
I-7
C-6
F-2
H-10
I-10
J-8
G-10
F-10
I-6
I-5
I-5
I-5
I-6
I-6
H-6
D-6
R710 R711
Ref. No.
D101
D102
D103
D104
D105
D106
D108
D110
D111
D113
D114
D115
D116
D117
D118
D119
D120
D121
D301
D303
D304
D322
D401
D501
D625
D626
D630
D653
D703
D814
D829
D831
D832
D833
D835
D907
D909
(Page 32)
11
(11)
J
CDX-GT800D/GT805DX
2
1
L
R
L
REAR
R
(SHASSIS)
7
8
9
10
11
12
13
14
CNJ101
(REMOTE IN)
FRONT
L
–2
R
–3
L
–4
R
–5
–6
CNP102
(BUS CONTROL IN)
Q408
C491
C227
C232
C188
C288
R505
6
AUDIO OUT
BUS
AUDIO ON
–1
C215
C178 C278
CNP102
CNP101
TP1
C228
R423
C210
C205
PJ401
D402
PJ501
D112
IC201
R275
R142
R174
C101
R274
R284
R143
CN401
C211
C212
C273
C283
C173
TH100
C183
RED
R285
R184
WHT
C
R175
R185
C142
ILL
R243
C242
R242
C229
C203
C204
C225
D109
B
5
PJ401
CN401
SUB OUT
(MONO)
PJ501
(ANTENNA)
4
C103
A
3
C214
C903
D904
R107
C705
C334
R657
FB332
C857
C305
DRIVING (F) ASSY
C306
C855
FB328
Q651
1
D651
C303
R658
C304
C424
C321
C311
FB501
M904
(OPEN/CLOSE)
C651
FB335
C854
L653
G
C656
Q652
R661
R704
C852
FB329
C655
FB333
L800
FB801
C421
20
C856
22 23
25
FB334
C859
C872
C814
R864
C422
30
1
40
IC
C333
R610
C860
R852
L801
11
12
10
15
5
R522
C510
C863
C865
R807
C885
D128
CNP301
C813
R808
C706
Q102
C861
R809
C812
C455
C811
R810
C480 C423
40
1 44
C410
C502
F
17
C481
C862
C871
C815
35
C433
C864
C816
C302
C456
C479
34
33
R455
C509
10
C434
R504
R521
R452
R451
C544
15
R453
R454
C513
C505
C817
C301
GT800D
R502
C869
Q801
C457
C870
R106
R104
CN702
C172
C182
C272
C458
GT805DX
5
E
C459
R380
C514
C503
C419
C282
(SHASSIS)
C420
R664
C102
C221
7
C223
L101
R105
1
D906
TP2
R108
R921
R920
Q402
C440
TUX501
C401
C226
Q401
D
C400
C443
C437
C441
Q703
Q702
CN702
WHT
1
RED
BLK
BLU
GRN
ORG
BRN
7
M
BLK
BLU
GRN
ORG
BRN
R654
R361
R314
JR602
C620
D621
J
D623
JR615
D828
D827
D826
D825
D824
D823
C341
D620
R644
C629
R622
C621
C340
C632
GT800D
L654
R623
R624
D830
R627
C622
D622
X551
D652
C623
R626
C624
X301
D834
C551
R312
C325
C560
L655
C318
R335
TH301
C559
TP9
C628
C315
C316
X302
R313
D836
R701
GT800D
GT805DX
C323
C326
C322
H
I
R655
C652
R321
C430
C403
T620
Q620
D624
(SHASSIS)
11
1-869-016- (11)
(SHASSIS)
A
SERVO BOARD
CN2
(Page 23)
CDX-GT800D/GT805DX
27
27
• Semiconductor Location
Ref. No.
D109
D112
D128
D402
D620
D621
D622
D623
D624
D651
D652
D823
D824
D825
D826
D827
D828
D830
Location
C-10
B-8
E-10
B-2
J-8
J-7
I-9
I-8
J-8
G-10
H-10
I-5
I-5
I-5
I-5
I-6
I-6
I-5
Ref. No.
D834
D836
D904
D906
Location
I-5
H-6
D-5
D-5
IC201
IC401
B-6
F-4
Q102
Q401
Q402
Q408
Q620
Q651
Q652
Q702
Q703
Q801
E-9
D-5
D-5
B-3
I-10
F-10
G-10
F-11
F-11
F-8
CDX-GT800D/GT805DX
• Refer to page 22 for Waveforms.
4-9. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 35 for IC Block Diagrams.
C424
C470
IC B/D
R474 R470
TUX501
C421
C419
C420
R411
R410
C417
C418
R478 C474
C409
IC472
R480 C476
C422
C423
C408
R476 R472
R487
IC401
R420
C482
R502
C472
R498
R405
R404
C480
C471
R488
C479
R475 R471
C509
C544
C505
C410
R461
R599
R454
C478
JR609
L401
R455
R481
R451
C477
R452
IC471
R504
FB502
FB501
R462
C469
C510
R453
C513
R522
R479
R521
C514
PJ501
C503
C481
C433 C434
R477 R473
R484
C455
C456
C457
C458
C459
L503
Q501
C473
R485
R501
C502
D501
C501
IC470
R505
C475
FB801
C885
C822
C811 C812 C813 C814
C883
R810 R809 R808 R807
C882
R858
C182
C881
R802 C815
R860
C850
R853
R801
R483
C172
C802
R380
L801
C820
C884
C872
C272
C851
IC B/D
Q380
C282
IC B/D
(Page 29)
R861
X801
Q551
C871
IC551
FB552 C553
C561
R552
C557
R553
C867
C869
C558
IC801
X551
C853
R655
Q651
L655
R852
L654
L653
L651
C653
R654
C559
C560
R554
C855
C866
R555
R556
R557
FB551
R664
Q801
C554
C555
C556
Q552
L652
L800
C852
C870
C552
C551
R551
C854
C868
C856 C857
C817 R811
C652
R657
R659
C816
R812
R863
C859
C863
C862
C860
C864
C861
R864
R854
R862
R855
C858
R660
D651
R656
R663
R661
D652
C654
IC B/D
R868
R869
C865
(Page 30)
CDX-GT800D/GT805DX
28
IC650
D653
Q652
C656
R851
C655
R658
R662
R859
C651
28
(Page 31)
CDX-GT800D/GT805DX
4-10. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) — • Refer to page 37 for IC Block Diagrams.
CN401
C411
FB402
R403
C442
C403
C443
R402
R408
C215
C210
C228
C205
C227
C278
C178
Q470
R409
IC B/D
R407
C412
D111
C188
C173 R174
C430
Q171
R142
C431
R175
R143
D113
IC474
C236 C206
R203
R242
C142
Q181
R184
R243
D112
R185
C183
PJ401
C288
D110
R406
C238 C218 R205
C242
Q408
D114
C208
C216
C209
C217
D115
C239
IC B/D
C283 R284
Q281
C219
R424
C491 R423
C237 C207 R206
IC402
D402
D116
CNP101
R285
R204
R434
(Page 28)
IC201
D117
D119
R436
D120
R275
C440
R433
C273
R274
Q271
R201
C201
C203
D121
D118
C211
R435
C439 C436
R202
Q402
C441
C202
C212
C204
C400
C221
C438
C223
D401
Q401
R431
R207
C214
R401
R429
C401
C225
C231
R432
R430
C226
R103
L101
C229
C437
C107
C232
D109
C103
R110
Q103
R109
R111
R112
D108
R921
R922
D909
Q907
C903
R929
R920
(Page 31)
(Page 30)
R108
R105
Q102
R104
CDX-GT800D/GT805DX
29
29
R106
C102 R107
D106
F901
CDX-GT800D/GT805DX
• Refer to page 22 for Waveforms.
• Refer to page 39 for IC Block Diagram.
4-11. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 43 for IC Pin Descriptions.
(Page 28)
(Page 29)
D906
D904
JR618
(Page 25)
C886
R856
IC802
L301
CNP301
R857
R610
C302
FB333
R323
R322
R381
R346
C301
R382
R365
R366
FB334
JR608
FB332
C333 C334 FB329
FB335
R309
R373
R372
JR607
FB328
R325
C305
C306
C304
C303
R321
R310
R311
R337
IC301
R307
L303
R364
D301
C331
C322
C328
C326
C321
C311
X302
IC303
C317
C323
(Page 31)
R342
C327
C332
R328
R701
R327
C315
X301
R361
R702
R306
R360
Q701
PH1
C316
TP9
R363
CN702
Q703
R704
R1
R2
R367
R305
S1
R341
R334
C313
Q702
R302
R703
IC B/D
R303
R335
D304
R356
R304
R332
IC701
IC703
IC702
C701 R708
D703
R707
R709
C702
R710
C708
C703
R706
C704
C705
R711
C709
C706
C707
CDX-GT800D/GT805DX
30
30
R343
R344
R345
R347
R357
R313
D907
R336
D322
R377
R333
R351
R350
R340
R339
R338
R315
C325
TH301
R314
C318
R312
M904
IC302
CDX-GT800D/GT805DX
4-12. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) — • Refer to page 40 for IC Block Diagrams.
(Page 28)
(Page 29)
Q301
R116
CNJ101
JR613
R625
R318
Q642
Q624
C112
R319
L304
CN606
C622 L620
C342
C340
Q623
Q302
C341
R627
C623
Q621
D624
C632
R626
R628
T620
L502
C620
D623
C512
D625
R621
D620
C624
R629
D814
R620
D836
D835
D630
D622
C628
Q622
C629
C621
D834
JR615
C626
D833
(Page 34)
D832
R622
D831
D830
D621
R623
R636
IC620
R845
Q620
D829
R630
R633
D827
R644
IC B/D
C625
R631
D828
R624
D826
R637
D825
D824
R632
D626
D823
JR604
D303
R348
Q303
R265
JR602
JR606
JR605
JR603
D128
R117
R118
IC B/D
(Page 30)
CNP102
R114
R115
C111
Q110
Q111
IC110
TH100
D101
C110
D102
R127
D103
R126
Q112
C101
D104
R101
D105
R102
Q101
R119
R990
R991
Q134
CDX-GT800D/GT805DX
31
31
LED990
CDX-GT800D/GT805DX
4-13. PRINTED WIRING BOARDS — PANEL SECTION — • Refer to page 22 for Circuit Boards Location.
2
1
3
4
5
6
: Uses unleaded solder.
7
8
9
10
11
12
13
14
A
R991
B
R990
LED990
(DISC IN)
11
1-869-017-
CN901
(FRONT PANEL DETECT)
S902
RESET
MAIN BOARD
11
(Page 26)
1-869-019-
D
11
C
DISPLAY BOARD
CN902
E
(Page 33)
(Page 26)
MAIN BOARD
CN606
B
F
G
H
CN607
JC901
11
1-869-019-
11
I
CDX-GT800D/GT805DX
32
32
D
RED
C
BLK
S901
11
CDX-GT800D/GT805DX
4-14. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 22 for Circuit Boards Location.
2
1
3
4
5
: Uses unleaded solder.
6
7
8
9
10
11
12
13
14
LED908,S903
Z/ANGLE
A
S903
S908
LED906
LED908
R904
LE
LE
D9
D9
12
02
B
R901
LED906,
S908
OFF
LE
D9
D9
13
LE
01
LED905
LED907
LED907,S904
MENU
S904
D9
D9
LE
LE
D9
04
C
14
S910
LE
LED905,
S910
MODE
LE
15
R903
D9
LSW906
LSW904
LSW905
LSW903
R905
03
S909
D
LSW901
LSW902
IC903
S907
S905
2
4
1
3
1-689-018-
LED909
11
LED911
LED901-904
(VOL ILLUMINATION)
LED910
LSW906
1/REP
LED911,S909
SOURCE
LSW905
2/SHUF
LSW902
5
LED903
4
LED904
3
LED910,S907
DSPL (US MODEL)
LSW901
6/PAUSE
LED909,S905
/IMAGE
IC903
LED912,913
>/SEEK +
( ILLUMINATION
)
AF/TA (E,CH MODEL)
E
(
LED914,915
./SEEK –
ILLUMINATION
11
)
(Page 32)
BASE PANEL BOARD
CN901
C
F
R970 C905
R902
R945
R943
D903
D920
S906
R937
FL900
FLUORESCENT INDICATOR
TUBE
R936
C921
D923
20
17
4
R939
R963
R962
C920
JC905
D901
JC903
R971
JC902
R964
FB905
FB908
C901
IC904
D904
1
C919
FMB11
JC920
JC907
R934
CN902
R950
R959
FB904
R961
R926
25
1
FB903
C915
R933
R931
FB912
FB911
26
X901
FB902
100
R958
FB921
R930
I
FB913
R956
S911
FB914
FB916
R951
FB919
R928
H
R982
C903
FB915
FB920
D902
FB901
R954
IC901
FB918
JC909
D907
D908
R952
R960
50
R974
R910
51
76
R955
75
R907
G
R922
R912
R953
R909
D921
R981
FB917
FMB12
R908
R906
R913
R924
R920
R941
R911
D922
11
JC910
1-689-018-
11
S906
SEEK + >/. SEEK –
/PUSH ENTER
S911
VOL/ENTER SOUND
J
• Semiconductor Location
CDX-GT800D/GT805DX
33
33
Ref. No.
D901
D902
D903
D904
D907
D908
Location
I-11
G-11
H-12
I-5
G-10
G-10
Ref. No.
D920
D921
D922
D923
Location
H-11
F-11
F-4
I-10
IC901
G-6
Ref. No.
IC903
IC904
Location
D-13
I-6
LED901
LED902
LED903
B-4
B-3
C-2
Ref. No.
LED904
LED905
LED906
LED907
LED908
LED909
Location
C-4
C-1
B-1
C-14
B-14
D-14
Ref. No.
LED910
LED911
LED912
LED913
LED914
LED915
Location
D-11
D-5
B-12
B-13
C-13
C-12
CDX-GT800D/GT805DX
• Refer to page 22 for Waveform.
4-15. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 45 for IC Pin Descriptions.
R934
R933
R931
R930
R928
R924
R922
R920
LSW905(2/2)
LSW903(2/2)
LSW901(2/2)
LSW906(2/2)
LSW904(2/2)
LSW902(2/2)
R926
S908
S903
R907
S909
LED906
LED903
LED901
LED904
LED902
R945
R943
LED905
JC907
R901
R908
S904
FB917
S910
R902
R909
S905
S906
R941
R903
R939
R936
R937
R953
D921
LSW906(1/2)
R910
LED914
LED912
LED910
LED915
LED913
LED911
LED908
S911
LED907
D922
1/REP
R904
S907
LSW905(1/2)
R911
LED909
(US MODEL) DSPL
(E,CH MODEL) AF/TA
R905
R952
2/SHUF
LSW901(1/2)
LSW904(1/2)
LSW902(1/2)
LSW903(1/2)
R912
IC901
R951
6/PAUSE
R906
FB916
R913
FB915
JC909
JC910
FB914
FB918
FB913
FB912
FB911
FB919
D902
JC905
R958
R954
FB903
FB901
FB904
R971
FB902
CN902
FB921
CN901
FB920
CN607
D901
FB905
FB908
R959
X901 C919
R955
JC903
JC901
R956
D903
C915
D907
(Page 31)
R960
R950
R961
D908
C903
D920
JC920
S902
R970
R981
C901
IC903
C905
IC904
FL900
34
34
C920
D923
C921
R982
S901
CDX-GT800D/GT805DX
JC902
D904
R962
R963 R964
R974
CDX-GT800D/GT805DX
• IC BLOCK DIAGRAMS
IDAC
VINR4
VINL4
VINR3
VINL3
VINR2
VINL2
VINR1
VINL1
AVDD5
A-GND
A-GND
AVDD4
FILTD
NC
NC
NC
AUXR2
AUXL2
VOUT4
IC801 ADAU1421YSTZ (MAIN Board (1/4))
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64
63 62 61
ADC
DAC
DAC
DAC
PROGRAMMABLE
AUDIO PROCESSOR
CORE
DAC
A-V
SYNC DELAY
MEMORY
SYNCHRONIZE
MULTI-CHANNEL
DIGITAL INPUT
I2C INTERFACE
60
59
58
57
56
55
54
53
52
VOUT3
VOUT2
VOUT1
AUXR1
AUXL1
AVDD3
HPR
HPL
A-GND
51
50
49
48
A-GND
PLL_LF
AVDD2
D-GND
47 DVDD
46 RESETB
SRC
ASYNCHRONIZE
DIGITAL INPUT
SYSTEM
CLOCKS
45 PWM4
44 PWM3
PLL
21
22 23 24 25
26 27
28
29 30 31 32
33 34 35 36 37 38 39 40
LRCLK0
BCLK0
D-GND
ODVDD
VDRIVE
D-VDD
D-GND
MCLKI
MCLKO
BCLK1
LRCLK1
SDO0
SDO1
NC
DVDD
MULTI-CHANNNEL
DIGITAL OUTPUTS
SDIN0
SDIN1
SDIN2
SDIN3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
DVDD
FILTA
VREF
A-GND
AVDDD1
NC
NC
NC
NC
NC
NC
NC
NC
D-GND
DVDD
I2C_AD0
I2C_SDA
I2C_SCL
NC
NC
D-GND
43 PWM2
42 PWM1
41 D-GND
35
CDX-GT800D/GT805DX
7
VCC
8
CS
CT
REF
IC650 NJM2379V (MAIN Board (1/4))
6
5
30µA
VREF
OSC
L.O
U.VLO
S.C.P
ER.AMP
0.52V
2
3
F.B
GND
4
OUT
1
IN
PWM
IC1 BA5968FP-E2 (SERVO Board (2/2))
28 REV
FWD 1
FWD REV
27 OPIN4+
LDCTL 2
OUTR OUTF
NC 3
26 OPIN4–
OPOUT1 4
25 OPOUT4
NC 5
24 OPIN3+
NC 6
23 OPIN3–
OPOUT2 7
POWVCC 8
VOL– 9
22 OPOUT3
VCC
MUTE
VOL+ 10
18 VOL3–
VOL2– 11
LEVEL
SHIFT
LEVEL
SHIFT
VOL2+ 12
17 VOL3+
VO1– 13
16 VOL4–
LEVEL
SHIFT
VO1+ 14
36
21 MUTE
20 VOL+
19 GND
LEVEL
SHIFT
15 VOL4+
CDX-GT800D/GT805DX
IC551 TDA7333013TR (MAIN Board (1/4))
3
INTERPOLATOR
BAND PASS
FILTER
MPX
REF3 2
REF2 3
REF1 4
VSS 5
SIGMA DELTA
CONVERTER
SINC4REG
VDDA 1
SINC4
FILTER
RAM
RDS
RDSREG BUFFER
INTN DEMODULATOR &
&
SYNCHRONIZATION
CONTROL
LOGIC
16 MPX
15 INTN
SDAOUT
SDAIN
TEST LOGIC
SCK
I C/SPI
&
INTERFACE SPI
PIN MUX'S
TESTREG
2
14
13
12
11
CSN
SA_DATAOUT
SDA_DATAIN
SCL_CLK
2
TM 6
10 XTO
OSCILLATOR
VDDD 7
9 XTI
RESETN 8
IC402 NJM2792V (MAIN Board (2/4))
GND (L) 1
LIFT AMP
20 CIN (L)
COUT (L) 2
19 OUT (RL)
OUT (FL) 3
FL- 4
18 RLSIGNAL AMP
SIGNAL AMP
FL+ 5
17 RL+
FRONT-LEFT
REAR-LEFT
16 VCC
REF 6
FRONT-RIGHT
REAR-RIGHT
FR+ 7
15 RR+
SIGNAL AMP
SIGNAL AMP
FR- 8
14 RR-
13 OUT (RR)
OUT (FL) 9
COUT (R) 10
12 CIN (R)
LIFT AMP
11 GND (R)
37
CDX-GT800D/GT805DX
RR-IN
FR-IN
RL-IN
FL-IN
NC
NC
ADJ
BP31
BP21
BP11
BP12
IC401 BD3426K-E2 (MAIN Board (1/4))
33
32
31
30
29
28
27
26
25
24
23
FADER
22 BP22
34
FADER
21 BP32
SUB-OUT 35
2CH
1CH
FADER
FL-OUT 36
BPF
GENERAL PURPOSE
(+20~-20dB/2dB STEP)
RL-OUT 37
FADER
FR-OUT 38
FADER
RR-OUT 39
FADER
SCF BASE & TREBLE
(+20~-20dB/2dB STEP)
19
+15dB~-32dB 1dB/STEP
-32dB~-46dB 2dB/STEP
-46dB~-78dB 4dB/STEP
-∞
VCC 40
20
VOLUME(0~-72dB, -∞dB)
LOUDNESS
LOUDNESS
ON/OFF
1CH
2CH
18
17
MUTE 41
MUTE
16 SUB-IN
VCO
15
DATA 43
INPUT GAIN 2
(0~+20dB)
INPUT GAIN 1
(0~+20dB)
2 WIRE SERIAL
CONTROL LOGIC
CLK 42
2CH
1CH
2CH
1CH
DUAL MODE INPUT SELECTOR
(3 SINGLE STEREO INPUT AND 1 GROUND ISOLATION INPUT)
12
DGND 44
1
2
3
4
5
6
7
8
9
10
AGND
FIL
AUX-R-IN
AUX-R-GND
AUX-L-GND
AUX-L-IN
CD-C-R
CD-C-L
TU-R
TU-L
VCC/2
38
14 L-OUT
13 R-OUT
11
CDX-GT800D/GT805DX
IC201 TDA8588AJ/N2/R1 (MAIN Board (2/4))
TAB 1
2 SDA
OUT FL- 3
I2C BUS
4 SCL
FL
OUT FL+ 5
6 VP2
OUT RL- 7
RL
8 PGND3
OUT RL+ 9
10 SVR
MUTE
INRL 11
PROTECTION
DIAGNOSTIC
INRR 15
12 INFL
14 INFR
MUTE
SGND 13
16 AC GND
VP
OUT RR+ 17
RR
18 PGND2
OUT RR- 19
20 VP1
OUT FR+ 21
FR
OUT FR- 23
STANDBY
MUTE
22 STB
CHIP DETECT
DIAGNOSTIC
24 PGND1
TEMPERATURE
PROTECTION
DIAG 25
ENABLE
LOGIC
26 RST
SW2(ANT REM) 27
SWITCH
SW1(ANT REM) 29
SWITCH
28 CRES
REGULATOR
30 REG1(AUDIO +B)
REG3(SERVO) 31
REG4(DR+B) 33
32 GND(REG)
34 REG5(ILL)
VP(REG) 35
REFERENCE
VOLTAGE
REG2(BU 5V) 37
REGULATOR
36 CBU
LOADDUMP
PROTECTION
BACK-UP
SWITCH
IC702 LB1930M-TLM-E (MAIN Board (3/4))
VCC 1
NC 2
10 NC
BUFFER
FIN 3
CONTROL
CIRCUIT
RIN 4
MOTOR
DRIVE
CIRCUIT
9 OUT1
8 NC
7 OUT2
BUFFER
SGND 5
6 PGND
39
CDX-GT800D/GT805DX
7
VCC
8
CS
CT
REF
IC620 NJM2377M(TE2) (MAIN Board (4/4))
6
5
30µA
VREF
OSC
L.O
U.VLO
S.C.P
ER.AMP
0.52V
F.B
3
4
OUT
2
GND
1
IN
PWM
IC110 BA8271F-E2 (MAIN Board (4/4))
BUS ON 1
BUS ON
SWITCH
RST 2
RESET
SWITCH
BATT 3
BATTERY
SWITCH
CLK 4
VREF 5
DATA I/O 6
GND 7
40
14 VCC
13
12
11
10
RST
BUS ON
CLK-IN
B-CHK
9 DATA IN
8 DATA OUT
CDX-GT800D/GT805DX
• IC PIN DESCRIPTIONS
• IC3 MB90486BPFV-G-177E1 (CD SYSTEM CONTROL) (SERVO BOARD (2/2))
Pin No.
Pin Name
I/O
Pin Description
1
CDON_1500MV
O
2 to 5
NC
—
Not used. (Open)
6
DRVON
O
Motor drive mute signal output
7
CD_BUS0
I/O
Bus data input/output 0
8
CD_BUS1
I/O
Bus data input/output 1
9
VSS
—
Ground
10
CD_BUS2
I/O
Bus data input/output 2
11
CD_BUS3
I/O
Bus data input/output 3
12
CD_BUCK
O
Bus clock signal output
13
CD_XCCE
O
Chip enable signal output
14
CD_XRST
O
Reset signal output
15
CD_ZDET
I
Zero detection signal input
16 to 20
NC
—
Not used. (Open)
21
VCC
—
Power supply pin (+3.3 V)
22
DAC_ZDETL
I
23
DAC_ZDETR
I
24
NC
—
25
RXD
I
UART RXD data input (MCBUS/Flash data input)
26
TXD
O
UART TXD data output (MCBUS/Flash data output)
27
DEC_SSTBY
O
SRAM STANDBY mode control signal output
28, 29
NC
—
Not used. (Open)
30
DEC_INT
I
31, 32
NC
—
Not used. (Open)
33
AVCC
—
Power supply pin (+3.3 V) for A/D converter
34
AVRH
—
External reference voltage for A/D converter
35
AVSS
—
Ground
36
NC
—
Not used. (Open)
Servo 1.5 V power supply control signal output
Not used. (Pull down)
Not used. (Pull down)
Not used. (Open)
Request signal input
37
DEC_XMUTE
O
Mute signal output
38, 39
NC
—
Not used. (Open)
40
VSS
—
Ground
41
NC
—
Not used. (Open)
L: mute
42
MEC_LIMIT
I
Sled limit in detection switch signal input
43
MEC_LOAD
O
Loading motor signal output (Load direction)
44
MEC_EJECT
O
Loading motor signal output (Eject direction)
45
MEC_INSW
I
Pack-in detection signal input
46
MEC_DSW
I
Chucking end detection switch signal input
47, 48
MD0, MD1
I
CPU operation mode designation signal input (Connected to Vcc.)
49
MD2
I
CPU operation mode designation signal input (Connected to Vss.)
50
BUS_ON
I
Bus on signal input
51
BU_IN
I
Backup power supply detect signal input
52
NC
I
Not used. (Open)
53
MEC_SELFSW
I
54, 55
NC
—
L: bus on
Disc insert detection switch signal input
L: disc in interruption
Not used. (Open)
56
UNISI
I
Control bus serial data input
57
UNISO
O
Control bus serial data output
58
UNICKI
I
Control bus serial clock input
59
LINKOFF
O
Bus link off signal output
60
A_ATT
O
Audio mute signal output
H: mute on
41
CDX-GT800D/GT805DX
Pin No.
Pin Name
I/O
61
XFLASH&EJECT_OK
I
Pin Description
62
OPEN_REQ
O
Front panel open/close request signal output
63
MECON
O
Mechanism deck power supply control signal output
64
CDON
O
Servo power supply control signal output
65
XUART
I
S-Bus/MC-Bus change signal input
66
ZMUTE
O
Zero detection mute signal output
67
MECON_CHK
I
CD +6V power rising detection signal input
68
CDON_CHK
I
CD +3.3V power rising detection signal input
69 to 74
NC
—
75
RSTX
I
76
NC
—
Not used. (Open)
77
X1A
—
Not used. (Open)
78
X0A
—
Connected to Vss.
79
VSS
—
80
X0
I
Main-clock INPUT (12 MHz)
Front panel open signal input
Not used. (Open)
System reset signal input
Ground
81
X1
O
Main-clock OUTPUT (12 MHz)
82
VCC
—
Power supply pin (+3.3 V)
83
XWD
I
84
XINIT3
I
Not used. (Open)
85
NC
—
Not used. (Open)
Connected to Vss.
86
XSJIG
I
Not used. (Open)
87 to 89
XINIT0 to 2
I
Not used. (Open)
90 to 96
NC
—
Not used. (Open)
97
XDES
I
Destination setting pin
98
XLINE
I
Not used. (Open)
99, 100
NC
—
Not used. (Open)
42
H: eject
Not used in this set.
H: S-Bus, L: MC-Bus
CDX-GT800D/GT805DX
• IC303 M30622MWP-304GP (SYSTEM CONTROL) (MAIN BOARD (3/4))
Pin No.
Pin Name
I/O
Pin Description
1
SIRCS
I
Remote control data signal input
2
FSW-IN
I
FL DC-DC converter frequency count input
3
UNI_SO
O
Control bus serial data output
4
UNI_SI
I
Control bus serial data input
5
UNI_CKO
O
Control bus serial clock output
6
BYTE
I
Not used (Connect to ground)
7
CNVSS
I
Flash write port
8
XCIN
I
Sub clock signal input (32.768 kHz)
Fixed at “L”
9
XCOUT
O
Sub clock signal output (32.768 kHz)
10
RESET
I
Reset signal input
11
XOUT
O
Main clock signal output (6 MHz)
12
VSS
—
Ground
13
XIN
I
14
VCC1
—
15
NMI
I
16
NC
—
17
DAVN
I
18
TUNER ATT-IN
I
Tuner attenuation zero cross input
19
NS-MASK
O
Tuner noise detect mask signal output
20
BEEP
O
Beep signal output
21
TUNER ATT
O
Tuner mute signal output
22
EESIO(TU)
I/O
Tuner pack EEPROM data signal input/output
23
EECKO(TU)
O
Tuner pack EEPROM clock signal output
24
NC
—
Not used (Open)
25
ATT
O
Line mute signal output
26
BUS/AUX
O
Buss audio/AUX exchange signal output
27
I2C_CKO
O
I2C serial transfer clock output
28
I2C_SIO
I/O
I2C serial data input/output
29
E_VOL_SO
O
E-VOL serial data output
30
E_VOL_MUTE
O
E-VOL mute signal output
31
E_VOL_CKO
O
E-VOL serial transfer clock output
Main clock signal input (6 MHz)
Power supply pin (+3.3 V)
Non-maskable interruption signal input
Fixed at “H”
Not used (Open)
RDS data block synchronization detection signal input
32
DSP_RESET
O
DSP reset signal output
33
DSP_I2C_SIO
I/O
DSP I2C data input/output
34
DSP_I2C_CKO
O
DSP I2C serial transfer clock output
35
EECKO (DSP)
O
EEPROM serial transfer clock output
36
EESIO (DSP)
I/O
EEPROM serial data input/output
37
DSP_ON
O
DSP power supply on signal output
38
NC
—
Not used (Open)
39
HOLD
I
Not used
40
AMP_DIAG
I
Amplifier self-diagnostic test function signal input
41
AMP_STB
O
Amplifier standby signal output
42
NC
—
Not used (Open)
43
NC
—
Not used (Open)
44
WRI/WR
I
45
NC
—
46
OPEN_REQ
I
47
EJECT_OK
O
Eject OK signal output
48
CDM_ON
I
Mechanism deck power supply ON signal input
49
CD_ON
I
Servo power supply ON signal input
Fixed at “L”
External data bus (WRI/WR) input
Fixed at “H”
Not used (Open)
Front panel open/close request signal input
43
CDX-GT800D/GT805DX
Pin No.
Pin Name
I/O
50
Z_DET
I
44
Pin Description
Zero detection mute signal input
51
ILL-IN
I
Illumination check signal input
52
ACC_IN
I
Accessory check signal input
53
TEL_ATT
I
Telephone mute signal input
54
TEST_IN
I
Test mode signal input
55
RC_IN1
I
Remote control signal input 1
56
SYSRESET
O
System reset signal output
57
BUS_ON
O
BUS ON signal output
58
BU_IN
I
59
NC
—
60
VCC2
—
Power supply (+3.3 V)
61
NC
—
Not used (Open)
62
VSS
—
Ground
63
MOTOR ON
O
Front panel motor drive power supply signal output
64
MOT+
O
Front panel open/close motor control signal output (+)
65
MOT–
O
Front panel open/close motor control signal output (–)
66
CLOSE_SW
I
Front panel close detection signal input
67
OPEN_SW
I
Front panel open detection signal input
Backup power supply detection signal input
Not used (Open)
68
P-SNSR
I
69
P-MONITOR
—
Drive mechanism gear rotary information input
70
DST_SEL1
I
Destination/setting port signal input 1
71
DST_SEL2
I
Destination/setting port signal input 2
72
FL_ON
O
FL power supply on/off signal output
73
FSW OUT
O
FL DC-DC converter frequency exchange signal output
74
FLD_ON
O
FL driver power supply on/off signal output
75
RE_1B
I
Rotary encoder signal input 1B
76
RE_1A
I
Rotary encoder signal input 1A
77
RE_2B
I
Rotary encoder signal input 2B
78
RE_2A
I
Rotary encoder signal input 2A
P-SNSR result’s monitor output
79
FP-IDET
I
Front panel motor over current detect signal input
80
TEMP-TR
I
Temperature detection signal input
81
NC
—
82
QUALITY
I
Tuner noise detect signal input
83
VSM
I
S-meter voltage signal input
84
KEY_IN0
I
Key signal input 1
85
KEY_IN1
I
Key signal input 2
86
RC_IN0
I
Remote control signal input 0
87
KEY_ACK2
I
Key acknowledge signal input 2
88
KEY_ACK0
I
Key acknowledge signal input 1
Not used (Open)
89
KEY_ACK1
I
Key acknowledge signal input 0
90
DISP_RESET
O
Display control reset signal output
91
NOSE_SW
I
Front panel detect signal input
92
NC
O
Not used (Open)
93
DISP_CE
O
Display control chip enable signal output
94
AVSS
—
Ground
95
DOOR_IND
O
DISC IN illumination on signal output
96
VREF
—
Reference voltage for A/D convert
97
AVCC
—
Power supply (+3.3 V)
98
DISP SI/RX
I
Display control serial data signal input
99
DISP SO/TX
O
Display control serial data signal output
100
DISP CKO
O
Display control serial transfer clock output
CDX-GT800D/GT805DX
• IC901 M30876MJB-053GP (FL DISPLAY CONTOROL) (DISPLAY BOARD)
Pin No.
Pin Name
I/O
Pin Description
1
SYS_CE
I
2
NC
—
Not used (Open)
3
FL_DAT3
O
FL serial data-3 output
4
NC
—
Not used (Open)
5
FL_CLK_IN
I
FL serial transfer clock input (Connected to 35,100 pin)
6
BYTE
I
Connected to ground
7
CNVSS
I
Flash write port
8
NC
—
Not used (Open)
Chip enable signal input
Fixed at “L”
9
NC
—
Not used (Open)
10
RESET
I
Reset signal input
11
XOUT
O
Main clock signal output (6.75 MHz)
12
VSS
—
Ground
13
XIN
I
14
VCC1
—
15
NMI
I
16 to 18
NC
—
19
GCP_TA4_IN
I
20
NC
—
Not used (Open)
21
NC
—
Not used (Open)
22
BK_TA3_OUT
O
FL BK signal output (Connected to 19 pin)
23
NC
—
Not used (Open)
24
LAT_TA2_OUT
O
FL LAT signal output
25 to 27
NC
—
Not used (Open)
28
GCP_TA0_OUT
O
FL GCP signal output
29
SYS_SO
O
Display serial data output
30
SYS_SI
I
Display serial data input
31
SYS_CLK
I
Display serial transfer clock input
32
NC
—
Not used (Open)
33
FL_DAT1
O
FL serial data-1 output
34
NC
—
Not used (Open)
35
FL_CLK
I
36 to 38
NC
—
39
HOLD
I
39 to 43
NC
—
Main clock signal input (6.75 MHz)
Power supply (+3.3V)
Non-maskable interruption signal input
Fixed at “H”
Not used (Open)
FL BK signal input (Connected to 22 pin)
FL serial transfer clock input (Connected to 5,100 pin)
Not used (Open)
external data bus (HOLD) input
Fixed at “L”
Not used (Open)
44
WRI/ER
I
45 to 59
NC
—
External data bus (WRI/WR) input
Not used (Open)
60
VCC2
—
Power supply (+3.3V)
61
NC
—
Not used (Open)
62
VSS
—
Ground
Fixed at “H”
63 to 93
NC
—
Not used (Open)
94
AVSS
—
Ground
95
NC
—
96
VREF
I
97
AVCC
—
Power supply (+3.3V)
98
NC
—
Not used (Open)
99
FL_DAT2
O
FL serial data-2 output
100
FL_CLK_OUT
O
FL serial transfer clock output (Connected to 5,35 pin)
Not used (Open)
Reference voltage input (Connected to AVCC)
45
CDX-GT800D/GT805DX
SECTION 5
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
5-1.
•
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
Accessories are given in the last of this parts list.
Abbreviation
CH : Chinese model
•
•
MAIN SECTION
A
MG-611WD-186//Q
#1
#1
not supplied
A
13
12
F901
#1
not supplied
not supplied
10
1
not supplied
9
B
11
8
#1
not supplied
7
not supplied
B #1
6
1
not supplied
(SUB PANEL board)
2
4
not supplied
3
5
Ref. No.
4
Part No.
Description
1
2
3
4
5
3-265-290-01
A-1159-588-A
2-189-852-01
3-230-416-02
3-042-244-11
SCREW (PANEL F)
BASE PANEL BOARD, COMPLETE
HOOK (DETACHABLE)
SCREW
SCREW (T)
6
7
8
X-2024-000-1 PANEL (SUB) ASSY, BASE
2-661-675-01 SHAFT (LOCK1)
2-661-676-01 SPRING (A90)
46
Remark
Ref. No.
Part No.
Description
9
10
11
12
13
2-661-674-01
2-189-853-01
X-2103-369-1
1-776-207-72
3-264-798-01
SPRING (B90)
BRACKET (PWB)
PANEL ASSY, SUB
CORD (WITH CONNECTOR) (POWER)
CAP
F901
#1
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
7-685-792-09 SCREW +PTT 2.6X6 (S)
Remark
CDX-GT800D/GT805DX
5-2.
MAIN BOARD SECTION
#2
52
#2
58
59
#1
58
56
not supplied
#1
55
57
TUX501
54
53
55
not supplied
not supplied
54
51
53
not supplied
Ref. No.
51
52
Part No.
Description
Remark
53
54
55
1-869-079-11 FLEXIBLE BOARD
1-790-355-54 CORD (WITH CONNECTOR) (RCA)
(SUB OUT (MONO))
3-262-621-01 GEAR (DRIVE SHAFT)
2-178-992-01 GUIDE (DRIVE SHAFT) (2)
2-593-195-01 SCREW (M2.6X6)
56
X-2025-441-2 DRIVING (F) ASSY
Ref. No.
Part No.
Description
57
58
59
59
TUX501
X-2025-442-2
3-376-464-11
A-1159-590-A
A-1159-840-A
A-3220-961-B
MOVE (F) ASSY, FOLLOW
SCREW (+PTT 2.6X6), GROUND POINT
MAIN BOARD, COMPLETE (GT800D)
MAIN BOARD, COMPLETE (GT805DX)
TUNER UNIT (TUX-032)
#1
#2
7-685-792-09 SCREW +PTT 2.6X6 (S)
7-685-793-09 SCREW +PTT 2.6X8 (S)
Remark
47
CDX-GT800D/GT805DX
5-3.
FRONT PANEL SECTION
112
111
110
108
106
105
110
not supplied
not supplied
109
FL900
not supplied
not supplied
101
not supplied
not supplied
not supplied
106
102
107
105
103
not supplied
not supplied
113
not supplied
113
not supplied
103
104
Ref. No.
Part No.
Description
Part No.
Description
101
102
102
103
104
3-013-634-01
X-2108-310-1
X-2108-313-1
3-250-543-02
X-2108-309-1
SPRING (RELEASE)
BUTTON ASSY (S) (GT805DX)
BUTTON ASSY (S) (GT800D)
SCREW (+B P-TITE M2)
PANEL (SV) ASSY, FRONT (GT805DX)
108
109
110
111
112
A-1159-597-A
2-189-782-01
3-250-543-21
X-2103-370-1
A-1159-595-A
DISPLAY BOARD, COMPLETE
PANEL, FRONT BACK
SCREW (+B P-TITE M2)
CASE ASSY (for FRONT PANEL)
PANEL COMPLETE ASSY, FRONT (GT800D)
104
105
106
107
X-2108-312-1
X-2108-311-1
2-547-413-01
2-189-846-01
PANEL (SV) ASSY, FRONT (GT800D)
KNOB ASSY (S)
RING (ENCODER)
FILTER (FL)
112
113
FL900
A-1159-843-A PANEL COMPLETE ASSY, FRONT (GT805DX)
2-189-849-01 CUSHION (GND)
1-519-842-11 INDICATOR TUBE, FLUORESCENT
48
Remark
Ref. No.
Remark
CDX-GT800D/GT805DX
5-4.
CD MECHANISM SECTION (1)
(MG-611WD-186//Q)
152
not supplied
(SENSOR board)
151
153
#3
154
not supplied
not supplied
155
156
157
158
159
160
Ref. No.
Part No.
Description
151
152
* 153
* 154
155
A-3372-444-B
3-253-729-11
X-2055-247-1
X-2055-248-1
3-257-892-12
CHASSIS (T) SUB ASSY
SPRING (LR), TENSION COIL
LEVER (LN) ASSY
LEVER (RN) ASSY
SPRING (DAMPER), COIL (GREEN)
156
Remark
Ref. No.
157
158
159
160
#3
Part No.
Description
3-259-033-01
2-345-767-11
A-1132-437-A
2-587-505-01
7-627-552-87
DAMPER (S)
SPRING (KF60), TENSION
SERVO BOARD, COMPLETE
SCREW
SCREW, PRECISION +P 1.7X2.2
Remark
3-257-892-01 SPRING (DAMPER), COIL (NATURAL)
49
CDX-GT800D/GT805DX
5-5.
CD MECHANISM SECTION (2)
(MG-611WD-186//Q)
205
206
207
204
(including M901)
#4
M902
not supplied
SW4
not supplied
not supplied
not supplied
203
not supplied
201
202
Ref. No.
Part No.
Description
201
202
0 203
204
205
A-1075-644-A
3-316-938-91
8-820-207-12
A-1075-645-A
A-3372-449-A
CHASSIS (OP) COMPLETE ASSY
SCREW (B1.4X5), TAPPING
OPTICAL PICK-UP (KSS1000E/K1RP)
CHASSIS (OP) SUB ASSY (including M901)
ARM SUB ASSY, CHUCKING
50
Remark
Ref. No.
206
207
M902
SW4
#4
Part No.
Description
A-3372-446-A
X-3384-090-3
A-3372-447-A
1-571-099-11
7-627-850-77
LEVER (SL) SUB ASSY
LEVER (SL) ASSY
MOTOR ASSY, SL (SLED)
SWITCH (1 KEY) (LIMIT)
SCREW, PRECISION +P 1.4X1.8
Remark
CDX-GT800D/GT805DX
5-6.
CD MECHANISM SECTION (3)
(MG-611WD-186//Q)
253
251
252
257
261
254
259
258
260
255
257
257
M903
#3
256
Ref. No.
Part No.
Description
251
252
253
254
255
3-348-993-01
2-186-699-01
A-1075-641-B
2-635-295-01
2-635-296-01
WASHER
GEAR (RA1)
ARM ASSY, ROLLER
SPRING (RAL-B)
SPRING (RAR-B)
256
257
3-259-469-12 SPRING (LE), LEAF
2-134-636-21 SCREW (M1.7X2.5)
Remark
Ref. No.
Part No.
Description
258
259
260
261
M903
2-186-696-02
3-345-648-91
A-1083-636-A
2-186-697-01
A-1075-643-A
BRACKET (LEM-N)
SCREW (M1.4), TOOTHED LOCK
GEAR (LE) ASSY
BEARING (LEB-N)
MOTOR ASSY, LE (LOADING)
#3
7-627-552-87 SCREW, PRECISION +P 1.7X2.2
Remark
51
CDX-GT800D/GT805DX
5-7.
CD MECHANISM SECTION (4)
(MG-611WD-186//Q)
304
305
302
308
306
301
303
307
Ref. No.
301
302
303
304
52
Part No.
Description
2-186-700-01
3-344-223-01
3-259-470-12
3-253-755-31
GEAR (CHK1)
WASHER
GEAR (LE1)
LEVER (D)
Remark
Ref. No.
Part No.
Description
305
* 306
307
308
2-630-962-01
2-590-545-01
A-1075-640-B
3-348-993-01
WASHER (SLIT)
GEAR (LE2-M)
CHASSIS (M) BLOCK ASSY
WASHER
Remark
CDX-GT800D/GT805DX
SECTION 6
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Abbreviation
CH : Chinese model
Ref. No.
Part No.
•
•
•
•
Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
CAPACITORS
uF : µF
COILS
uH : µH
Description
Remark
Ref. No.
Part No.
< CONNECTOR >
1-691-365-61 CONNECTOR, FFC/FPC (ZIF) 27P
1-818-142-11 SOCKET, CONNECTOR 20P
< JUMPER RESISTOR >
JC901
1-216-864-11 SHORT CHIP
DISPLAY
The components identified by
mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
Description
Remark
< RESISTOR >
A-1159-588-A BASE PANEL BOARD, COMPLETE
***************************
CN607
CN901
BASE PANEL
0
< SWITCH >
S901
1-786-101-22 SWITCH, DETECTION (FRONT PANEL DETECT)
S902
1-786-157-11 SWITCH, TACTILE (RESET)
*************************************************************
A-1159-597-A DISPLAY BOARD, COMPLETE
************************
2-189-846-01 FILTER (FL)
D923
FB901
FB902
FB903
FB904
1-216-295-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-864-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
0
100
100
100
0
FB905
FB908
FB911
FB912
FB913
1-216-809-11
1-216-809-11
1-216-864-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
FB914
FB915
FB916
FB917
FB918
1-216-809-11
1-216-809-11
1-216-809-11
1-216-864-11
1-216-864-11
FB919
FB920
FB921
5%
5%
5%
1/10W
1/10W
1/10W
100
100
0
100
100
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
100
100
100
0
0
5%
5%
5%
1/10W
1/10W
1/10W
1-216-864-11 SHORT CHIP
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
0
100
100
5%
5%
1/10W
1/10W
< CAPACITOR >
< FLUORESCENT INDICATOR TUBE >
C901
C903
C905
C915
C919
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C920
C921
1-107-826-11 CERAMIC CHIP
1-100-758-11 CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
0.1uF
0.047uF
10%
10%
16V
250V
FL900
1-519-842-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC901
IC903
IC904
6-806-245-01 IC M30876MJB-053GP
6-600-163-01 IC RS-770 (IR)
8-759-659-13 IC PST3428UL
< JUMPER RESISTOR >
< CONNECTOR >
CN902
1-818-141-11 PLUG, CONNECTOR 20P
< DIODE >
D901
D902
D903
D904
D907
6-500-886-01
6-500-886-01
6-501-170-01
6-501-193-01
6-501-170-01
DIODE
DIODE
DIODE
DIODE
DIODE
RSA6.1ENTR
RSA6.1ENTR
UDZW-TE17-6.8B
1SS355WTE-17
UDZW-TE17-6.8B
D908
D920
D921
D922
6-501-170-01
6-501-170-01
6-501-170-01
6-501-170-01
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-6.8B
UDZW-TE17-6.8B
UDZW-TE17-6.8B
UDZW-TE17-6.8B
JC902
JC903
JC905
JC907
JC909
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC910
JC920
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
< DIODE >
LED901
LED902
LED903
LED904
LED905
6-500-476-01
6-500-476-01
6-500-476-01
6-500-476-01
6-500-476-01
LED
LED
LED
LED
LED
SML310BA1TT86 (VOL ILLUMINATION)
SML310BA1TT86 (VOL ILLUMINATION)
SML310BA1TT86 (VOL ILLUMINATION)
SML310BA1TT86 (VOL ILLUMINATION)
SML310BA1TT86 (MODE)
53
CDX-GT800D/GT805DX
DISPLAY
Ref. No.
LED906
LED907
LED908
LED909
LED910
MAIN
Part No.
Description
6-500-476-01
6-500-476-01
6-500-476-01
6-500-476-01
6-500-475-01
LED
LED
LED
LED
LED
Remark
SML310BA1TT86 (OFF)
SML310BA1TT86 (MENU)
SML310BA1TT86 (Z/ANGLE)
SML310BA1TT86 ( /IMAGE)
SML310BATT86 (DSPL) (US)
LED910 6-500-475-01 LED SML310BATT86 (AF/TA) (E,CH)
LED911 6-500-475-01 LED SML310BATT86 (SOURCE)
LED912 6-500-476-01 LED SML310BA1TT86
(SEEK +/> ILLUMINATION)
LED913 6-500-476-01 LED SML310BA1TT86
(SEEK +/> ILLUMINATION)
LED914 6-500-476-01 LED SML310BA1TT86
(./SEEK – ILLUMINATION)
LED915 6-500-476-01 LED SML310BA1TT86
(./SEEK – ILLUMINATION)
Ref. No.
Part No.
Description
R955
R956
R958
R959
R960
1-216-833-11
1-216-809-11
1-216-825-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
2.2K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R961
R962
R963
R964
R970
1-216-845-11
1-216-845-11
1-216-017-11
1-216-017-11
1-216-845-11
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
100K
100K
47
47
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R971
R974
R981
R982
1-216-864-11
1-216-864-11
1-216-864-11
1-216-821-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
0
0
0
1K
5%
1/10W
< SWITCH >
< SWITCH >
LSW901
LSW902
LSW903
LSW904
LSW905
1-786-807-11
1-786-807-11
1-786-807-11
1-786-807-11
1-786-807-11
SWITCH, TACTILE (WITH LED) (6/PAUSE)
SWITCH, TACTILE (WITH LED) (5)
SWITCH, TACTILE (WITH LED) (4)
SWITCH, TACTILE (WITH LED) (3)
SWITCH, TACTILE (WITH LED) (2/SHUF)
LSW906 1-786-807-11 SWITCH, TACTILE (WITH LED) (1/REP)
S903
S904
S905
S907
S908
1-786-653-11
1-786-653-11
1-786-653-11
1-786-653-11
1-786-653-11
S909
S910
1-786-653-11 SWITCH, TACTILE (SOURCE)
1-786-653-11 SWITCH, TACTILE (MODE)
< RESISTOR >
SWITCH, TACTILE (Z/ANGLE)
SWITCH, TACTILE (MENU)
SWITCH, TACTILE ( /IMAGE)
SWITCH, TACTILE (AF/TA)
SWITCH, TACTILE (OFF)
< ROTARY ENCODER >
R901
R902
R903
R904
R905
1-218-843-11
1-218-843-11
1-218-843-11
1-218-847-11
1-218-851-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
680
1K
1.5K
0.5%
0.5%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R906
R907
R908
R909
R910
1-218-851-11
1-218-843-11
1-218-843-11
1-218-843-11
1-218-847-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
680
680
680
1K
0.5%
0.5%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R911
R912
R913
R920
R922
1-218-851-11
1-218-851-11
1-218-855-11
1-216-812-11
1-216-812-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
1.5K
2.2K
180
180
0.5%
0.5%
0.5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R924
R926
R928
R930
R931
1-216-812-11
1-216-812-11
1-216-812-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
180
180
180
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C101
C102
C103
C107
C110
1-126-940-11
1-126-960-11
1-112-839-11
1-107-826-11
1-162-970-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
330uF
1uF
4700uF
0.1uF
0.01uF
10%
10%
25V
50V
50V
16V
25V
R933
R934
R936
R937
R939
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-812-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
180
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C111
C112
C142
C172
C173
1-162-970-11
1-162-964-11
1-162-927-11
1-124-717-85
1-124-721-85
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.01uF
0.001uF
100PF
1uF
10uF
10%
10%
5%
20%
20%
25V
50V
50V
50V
50V
R941
R943
R945
R950
R951
1-216-812-11
1-216-812-11
1-216-812-11
1-216-825-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
180
180
180
2.2K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C178
C182
C183
C188
C201
1-162-927-11
1-124-717-85
1-124-721-85
1-162-927-11
1-164-489-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
100PF
1uF
10uF
100PF
0.22uF
5%
20%
20%
5%
10%
50V
50V
50V
50V
16V
R952
R953
R954
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-833-11 METAL CHIP
100K
100K
10K
5%
5%
5%
1/10W
1/10W
1/10W
C202
C203
C204
1-162-923-11 CERAMIC CHIP
1-126-961-11 ELECT
1-124-695-85 ELECT
47PF
2.2uF
22uF
5%
20%
20%
50V
50V
25V
54
S906
S911
1-478-474-12 ENCODER, ROTARY
(SEEK + >/. SEEK –/PUSH ENTER)
1-478-474-12 ENCODER, ROTARY (VOL/ENTER SOUND)
< VIBRATOR >
X901
1-813-522-21 VIBRATOR, CERAMIC (6.75MHz)
*************************************************************
A-1159-590-A MAIN BOARD, COMPLETE (GT800D)
A-1159-840-A MAIN BOARD, COMPLETE (GT805DX)
*********************
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-685-794-09 SCREW +PTT 2.6X10 (S)
< CAPACITOR >
20%
20%
CDX-GT800D/GT805DX
MAIN
Ref. No.
Part No.
Description
Part No.
Description
C205
C206
C207
C208
C209
1-115-340-11
1-165-908-11
1-165-908-11
1-162-966-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
1uF
1uF
0.0022uF
0.0022uF
10%
10%
10%
10%
10%
25V
10V
10V
50V
50V
Remark
Ref. No.
C341
C342
C400
C401
C403
1-162-970-11
1-162-970-11
1-124-717-85
1-126-947-11
1-126-962-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.01uF
0.01uF
1uF
47uF
3.3uF
10%
10%
20%
20%
20%
25V
25V
50V
35V
50V
Remark
C210
C211
C212
C214
C215
1-115-340-11
1-165-908-11
1-126-934-11
1-126-964-11
1-115-340-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
0.22uF
1uF
220uF
10uF
0.22uF
10%
10%
20%
20%
10%
25V
10V
16V
50V
25V
C408
C409
C410
C411
C412
1-117-863-11
1-117-863-11
1-124-721-85
1-165-908-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.47uF
10uF
1uF
1uF
10%
10%
20%
10%
10%
6.3V
6.3V
50V
10V
10V
C216
C217
C218
C219
C221
1-162-966-11
1-162-966-11
1-165-908-11
1-165-908-11
1-126-933-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.0022uF
0.0022uF
1uF
1uF
100uF
10%
10%
10%
10%
20%
50V
50V
10V
10V
16V
C417
C418
C419
C420
C421
1-117-863-11
1-117-863-11
1-117-863-11
1-117-863-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.47uF
0.47uF
0.47uF
0.001uF
10%
10%
10%
10%
10%
6.3V
6.3V
6.3V
6.3V
50V
C223
C225
C226
C227
C228
1-126-964-11
1-165-908-11
1-126-934-11
1-115-340-11
1-115-340-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
10uF
1uF
220uF
0.22uF
0.22uF
20%
10%
20%
10%
10%
50V
10V
16V
25V
25V
C422
C423
C424
C430
C431
1-162-964-11
1-162-964-11
1-162-964-11
1-126-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
10uF
0.1uF
10%
10%
10%
20%
10%
50V
50V
50V
50V
16V
C229
C231
C232
C236
C237
1-115-340-11
1-162-970-11
1-107-826-11
1-165-908-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.01uF
0.1uF
1uF
1uF
10%
10%
10%
10%
10%
25V
25V
16V
10V
10V
C433
C434
C436
C437
C438
1-107-826-11
1-124-673-85
1-107-826-11
1-126-934-11
1-162-965-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
100uF
0.1uF
220uF
0.0015uF
10%
20%
10%
20%
10%
16V
10V
16V
16V
50V
C238
C239
C242
C272
C273
1-165-908-11
1-165-908-11
1-162-927-11
1-124-717-85
1-124-721-85
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
1uF
1uF
100PF
1uF
10uF
10%
10%
5%
20%
20%
10V
10V
50V
50V
50V
C439
C440
C441
C442
C443
1-162-965-11
1-126-934-11
1-124-673-85
1-162-927-11
1-126-964-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
0.0015uF
220uF
100uF
100PF
10uF
10%
20%
20%
5%
20%
50V
16V
10V
50V
50V
C278
C282
C283
C288
C301
1-162-927-11
1-124-717-85
1-124-721-85
1-162-927-11
1-126-933-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
100PF
1uF
10uF
100PF
100uF
5%
20%
20%
5%
20%
50V
50V
50V
50V
16V
C455
C456
C457
C458
C459
1-162-966-11
1-162-966-11
1-162-966-11
1-162-966-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0022uF
0.0022uF
0.0022uF
0.0022uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C302
C303
C304
C305
C306
1-107-826-11
1-126-933-11
1-107-826-11
1-126-933-11
1-107-826-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
100uF
0.1uF
100uF
0.1uF
10%
20%
10%
20%
10%
16V
16V
16V
16V
16V
C469
C470
C471
C472
C473
1-162-964-11
1-164-174-11
1-164-174-11
1-164-174-11
1-164-174-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.0082uF
0.0082uF
0.0082uF
0.0082uF
10%
10%
10%
10%
10%
50V
25V
25V
25V
25V
C311
C313
C315
C316
C317
1-126-916-11
1-107-826-11
1-162-917-11
1-162-917-11
1-165-908-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1000uF
0.1uF
15PF
15PF
1uF
20%
10%
5%
5%
10%
6.3V
16V
50V
50V
10V
C474
C475
C476
C477
C478
1-162-964-11
1-107-826-11
1-162-964-11
1-162-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
0.001uF
0.001uF
0.1uF
10%
10%
10%
10%
10%
50V
16V
50V
50V
16V
C318
C321
C322
C323
C325
1-162-970-11
1-124-635-00
1-162-919-11
1-162-919-11
1-162-970-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
220uF
22PF
22PF
0.01uF
10%
20%
5%
5%
10%
25V
6.3V
50V
50V
25V
C479
C480
C481
C482
C491
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-162-964-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
CERAMIC CHIP
0
0
0
0
0.001uF
10%
50V
C326
C327
C328
C331
C332
1-126-924-11
1-162-970-11
1-162-970-11
1-162-970-11
1-107-826-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
330uF
0.01uF
0.01uF
0.01uF
0.1uF
20%
10%
10%
10%
10%
10V
25V
25V
25V
16V
C501
C502
C503
1-162-970-11 CERAMIC CHIP
1-126-964-11 ELECT
1-126-963-11 ELECT
0.01uF
10uF
4.7uF
10%
20%
20%
C505
1-162-964-11 CERAMIC CHIP
0.001uF
10%
C333
C334
C340
1-126-933-11 ELECT
1-107-826-11 CERAMIC CHIP
1-126-947-11 ELECT
100uF
0.1uF
47uF
20%
10%
20%
16V
16V
35V
C509
1-162-970-11 CERAMIC CHIP
0.01uF
10%
C510
1-162-970-11 CERAMIC CHIP
0.01uF
10%
25V
50V
50V
(GT800D)
50V
(GT800D)
25V
25V
55
CDX-GT800D/GT805DX
MAIN
Ref. No.
Part No.
Description
Remark
C512
C513
C514
1-107-725-11 CERAMIC CHIP
1-126-933-11 ELECT
1-107-826-11 CERAMIC CHIP
0.1uF
100uF
0.1uF
C544
C551
1-162-970-11 CERAMIC CHIP
1-126-947-11 ELECT
0.01uF
47uF
10%
20%
10%
16V
16V
16V
(GT805DX)
10%
25V
20%
35V
(GT800D)
25V
(GT800D)
16V
(GT800D)
16V
(GT800D)
16V
(GT800D)
16V
(GT800D)
Ref. No.
Part No.
Description
C820
C822
C850
C851
C852
1-216-864-11
1-162-964-11
1-107-826-11
1-107-826-11
1-107-826-11
SHORT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0
0.001uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
50V
16V
16V
16V
C853
C854
C855
C856
C857
1-107-826-11
1-124-224-61
1-124-224-61
1-107-826-11
1-124-224-61
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
0.1uF
47uF
47uF
0.1uF
47uF
10%
20%
20%
10%
20%
16V
6.3V
6.3V
16V
6.3V
C858
C859
C860
C861
C862
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C863
C864
C865
C866
C867
1-124-224-61
1-124-224-61
1-124-224-61
1-107-826-11
1-107-826-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
47uF
47uF
47uF
0.1uF
0.1uF
20%
20%
20%
10%
10%
6.3V
6.3V
6.3V
16V
16V
C868
C869
C870
C871
C872
1-107-826-11
1-124-224-61
1-124-224-61
1-124-224-61
1-107-826-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
0.1uF
47uF
47uF
47uF
0.1uF
10%
20%
20%
20%
10%
16V
6.3V
6.3V
6.3V
16V
FILM CHIP
FILM CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.001uF
0.1uF
0.001uF
0.1uF
4.7uF
2%
5%
10%
10%
20%
50V
16V
50V
16V
50V
0.1uF
4.7uF
10%
20%
16V
50V
C552
1-162-970-11 CERAMIC CHIP
0.01uF
10%
C553
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C554
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C555
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C556
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C557
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C558
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C559
1-162-917-11 CERAMIC CHIP
15PF
5%
C560
1-162-917-11 CERAMIC CHIP
15PF
5%
C561
1-162-959-11 CERAMIC CHIP
330PF
5%
C620
C621
C622
C623
C624
1-104-665-11
1-128-552-11
1-126-934-11
1-126-964-11
1-164-315-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
100uF
47uF
220uF
10uF
470PF
20%
20%
20%
20%
5%
25V
63V
16V
50V
50V
C881
C882
C883
C884
C885
1-135-820-21
1-127-956-21
1-162-964-11
1-107-826-11
1-126-163-11
C625
C626
C628
C629
C632
1-162-966-11
1-164-004-11
1-107-826-11
1-126-933-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.0022uF
0.1uF
0.1uF
100uF
0.1uF
10%
10%
10%
20%
10%
50V
25V
16V
16V
16V
C886
C903
1-107-826-11 CERAMIC CHIP
1-126-963-11 ELECT
C651
C652
C653
C654
C655
1-126-933-11
1-126-963-11
1-107-826-11
1-162-969-11
1-126-933-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
100uF
4.7uF
0.1uF
0.0068uF
100uF
20%
20%
10%
10%
20%
16V
50V
16V
25V
16V
C656
C701
C702
C703
C704
1-126-934-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220uF
0.1uF
0.1uF
0.1uF
0.1uF
20%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C705
C706
C707
C708
C709
1-126-947-11
1-107-826-11
1-164-004-11
1-107-826-11
1-107-826-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.1uF
0.1uF
0.1uF
0.1uF
20%
10%
10%
10%
10%
35V
16V
25V
16V
16V
C802
C811
C812
C813
C814
1-162-967-11
1-104-951-11
1-104-951-11
1-104-951-11
1-104-951-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.0033uF
10uF
10uF
10uF
10uF
10%
20%
20%
20%
20%
50V
16V
16V
16V
16V
C815
C816
C817
1-104-951-11 ELECT
1-104-951-11 ELECT
1-104-951-11 ELECT
10uF
10uF
10uF
20%
20%
20%
16V
16V
16V
16V
(GT800D)
16V
(GT800D)
50V
(GT800D)
50V
(GT800D)
50V
(GT800D)
Remark
< CONNECTOR >
* CN401
CN606
* CN702
CNP101
CNP102
1-564-506-11
1-691-365-61
1-566-762-11
1-774-701-21
1-580-907-41
PLUG, CONNECTOR 3P
CONNECTOR, FFC/FPC (ZIF) 27P
PIN, CONNECTOR (PC BOARD) 7P
PIN, CONNECTOR 16P
PLUG, CONNECTOR (BUS CONTROL IN)
CNP301 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P
< JACK >
CNJ101 1-566-822-41 JACK (REMOTE IN)
< DIODE >
56
D101
D102
D103
D104
D105
6-501-180-01
6-501-180-01
8-719-058-24
6-501-169-01
6-501-180-01
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-18B
UDZW-TE17-18B
RB501V-40TE-17
UDZW-TE17-6.2B
UDZW-TE17-18B
D106
D108
D109
D110
D111
6-501-170-01
6-501-180-01
8-719-049-38
8-719-053-18
8-719-053-18
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-6.8B
UDZW-TE17-18B
1N5404TU
1SR154-400TE-25
1SR154-400TE-25
D112
D113
8-719-053-18 DIODE 1SR154-400TE-25
8-719-053-18 DIODE 1SR154-400TE-25
CDX-GT800D/GT805DX
MAIN
Ref. No.
Part No.
Description
D114
D115
D116
D117
D118
8-719-053-18
8-719-053-18
8-719-053-18
8-719-053-18
6-500-508-01
DIODE
DIODE
DIODE
DIODE
DIODE
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
RR263M-400FTR
Remark
D119
D120
D121
D128
D301
6-500-508-01
6-500-508-01
6-500-508-01
6-501-051-01
6-501-013-01
DIODE
DIODE
DIODE
DIODE
DIODE
RR263M-400FTR
RR263M-400FTR
RR263M-400FTR
BAT54CLT1G
BAT54ALT1G
D303
D304
D322
D401
D402
6-501-193-01
6-501-193-01
8-719-060-48
6-501-193-01
6-501-170-01
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355WTE-17
1SS355WTE-17
RB751V-40TE-17
1SS355WTE-17
UDZW-TE17-6.8B
D501
D620
D621
D622
D623
6-501-168-01
8-719-053-18
8-719-053-18
6-501-089-01
8-719-067-83
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-5.6B
1SR154-400TE-25
1SR154-400TE-25
RF101L2STE25
RB161L-40TE25
D624
D625
D626
D630
D651
8-719-067-83
6-501-180-01
6-501-167-01
1-216-295-11
6-501-089-01
DIODE RB161L-40TE25
DIODE UDZW-TE17-18B
DIODE UDZW-TE17-5.1B
SHORT CHIP
0
DIODE RF101L2STE25
D652
D653
D703
D814
D823
6-501-170-01
6-501-193-01
8-719-914-44
6-501-180-01
6-501-170-01
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-6.8B
1SS355WTE-17
DAP202K
UDZW-TE17-18B
UDZW-TE17-6.8B
D824
D825
D826
D827
D828
6-501-170-01
6-501-170-01
6-501-170-01
6-501-170-01
6-501-170-01
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-6.8B
UDZW-TE17-6.8B
UDZW-TE17-6.8B
UDZW-TE17-6.8B
UDZW-TE17-6.8B
D829
D830
D831
D832
D833
6-501-170-01
6-501-170-01
6-501-170-01
6-501-170-01
6-501-170-01
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-6.8B
UDZW-TE17-6.8B
UDZW-TE17-6.8B
UDZW-TE17-6.8B
UDZW-TE17-6.8B
D834
D835
D836
D904
D906
6-501-170-01
6-501-170-01
6-501-170-01
6-501-193-01
6-501-193-01
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-6.8B
UDZW-TE17-6.8B
UDZW-TE17-6.8B
1SS355WTE-17
1SS355WTE-17
D907
D909
8-719-060-48 DIODE RB751V-40TE-17
6-501-193-01 DIODE 1SS355WTE-17
Ref. No.
Part No.
Description
Remark
FB551
1-216-001-00 RES-CHIP
10
5%
FB552
1-216-001-00 RES-CHIP
10
5%
FB801
1-500-245-11 INDUCTOR, FERRITE BEAD
1/10W
(GT800D)
1/10W
(GT800D)
< IC >
IC110
IC201
IC301
IC302
IC303
6-703-884-01
6-705-359-02
6-705-373-01
8-759-659-13
6-806-246-01
IC
IC
IC
IC
IC
BA8271F-E2
TDA8588AJ/N2/R1
MM3123DPLE
PST3428UL
M30622MWP-304GP
IC401
IC402
IC470
IC471
IC472
6-709-028-01
6-709-146-01
8-759-697-21
8-759-697-21
8-759-697-21
IC
IC
IC
IC
IC
BD3426K-E2
NJM2792V(TE2)
NJM4565V(TE2)
NJM4565V(TE2)
NJM4565V(TE2)
IC474
IC551
IC620
IC650
IC701
8-759-681-42
6-803-747-01
6-705-542-01
6-709-000-01
8-759-693-13
IC
IC
IC
IC
IC
NJM12902V(TE2)
TDA7333013TR (GT800D)
NJM2377M(TE2)
NJM2379V
NJM12904V(TE2)
IC702
IC703
IC801
IC802
8-759-527-33
6-706-999-01
6-709-063-01
6-703-996-01
IC
IC
IC
IC
LB1930M-TLM-E
BA09CC0WFP-E2
ADAU1421YSTZ
BR24L04FV-WE2
< JUMPER RESISTOR >
JR602
JR603
JR604
JR605
JR606
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0 (GT800D)
0
0
0
JR607
JR608
JR609
JR613
JR615
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-803-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
0
0
0
0
33
JR618
1-216-295-11 SHORT CHIP
5%
1/10W
0
< COIL >
< JUMPER RESISTOR >
FB328
FB329
FB332
FB333
FB334
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
FB335
FB402
FB501
FB502
1-216-295-11
1-414-813-11
1-216-295-11
1-216-295-11
SHORT CHIP
0
FERRITE, EMI (SMD) (2012)
SHORT CHIP
0
SHORT CHIP
0
L101
L301
L303
L304
L401
1-456-617-11
1-414-398-11
1-414-398-11
1-216-296-11
1-414-394-41
COIL, CHOKE
INDUCTOR
INDUCTOR
SHORT CHIP
INDUCTOR
10uH
10uH
0
2.2uH
L502
L503
L620
L651
L652
1-216-296-11
1-414-394-41
1-457-073-11
1-457-073-11
1-457-073-11
SHORT CHIP
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
0
2.2uH
47uH
47uH
47uH
L653
L654
L655
L800
L801
1-414-394-41
1-216-296-11
1-216-296-11
1-414-398-11
1-414-400-41
INDUCTOR
SHORT CHIP
SHORT CHIP
INDUCTOR
INDUCTOR
2.2uH
0
0
10uH
22uH
57
CDX-GT800D/GT805DX
MAIN
Ref. No.
Part No.
Description
Remark
< JACK >
PJ401
PJ501
1-774-700-11 JACK, PIN 6P (AUDIO OUT FRONT/REAR,
BUS AUDIO IN)
1-815-185-13 JACK (ANTENNA)
< TRANSISTOR >
Q101
Q102
Q103
Q110
Q111
8-729-027-43
8-729-120-28
8-729-120-28
8-729-027-23
8-729-027-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146
2SC1623-L5L6
2SC1623-L5L6
DTA114EKA-T146
DTA114EKA-T146
Q112
Q134
Q171
Q181
Q271
8-729-027-43
8-729-027-43
6-550-752-01
6-550-752-01
6-550-752-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146
DTC114EKA-T146
DTC614TKT146
DTC614TKT146
DTC614TKT146
Q281
Q301
Q302
Q303
Q380
6-550-752-01
6-551-120-01
8-729-027-43
8-729-027-43
1-801-806-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC614TKT146
2SA2119K
DTC114EKA-T146
DTC114EKA-T146
DTC144EKA (GT800D)
Q401
Q402
Q408
Q470
Q501
8-729-027-46
8-729-027-23
6-550-683-01
6-550-752-01
6-551-431-01
TRANSISTOR DTC114YKA-T146
TRANSISTOR DTA114EKA-T146
FET RJK005N03-T146
TRANSISTOR DTC614TKT146
TRANSISTOR 2SC6027T100-QR
Q551
Q552
Q620
Q621
Q622
8-729-026-49
1-801-806-11
6-551-131-01
8-729-027-23
1-801-806-11
TRANSISTOR 2SA1037AK-T146-R (GT800D)
TRANSISTOR DTC144EKA (GT800D)
FET 2SK3614-TD-E
TRANSISTOR DTA114EKA-T146
TRANSISTOR DTC144EKA
Q623
Q624
Q642
Q651
Q652
1-801-806-11
1-801-806-11
8-729-027-23
6-550-877-01
6-550-683-01
TRANSISTOR DTC144EKA
TRANSISTOR DTC144EKA
TRANSISTOR DTA114EKA-T146
TRANSISTOR 2SA2049T100R
FET RJK005N03-T146
Q701
Q702
Q703
Q801
Q907
1-801-806-11
1-801-806-11
8-729-027-23
8-729-106-60
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC144EKA
DTC144EKA
DTA114EKA-T146
2SB1115A-YQ
2SC1623-L5L6
Ref. No.
Part No.
Description
R117
R118
R119
R126
R127
1-216-821-11
1-216-821-11
1-216-829-11
1-216-849-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
4.7K
220K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R142
R143
R174
R175
R184
1-216-833-11
1-216-833-11
1-216-813-11
1-216-841-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
220
47K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R185
R201
R202
R203
R204
1-216-841-11
1-216-841-11
1-216-811-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
150
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R205
R206
R207
R242
R243
1-216-821-11
1-216-821-11
1-216-821-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R265
R274
R275
R284
R285
1-216-864-11
1-216-813-11
1-216-841-11
1-216-813-11
1-216-841-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
220
47K
220
47K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R302
R303
R304
R305
R306
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R307
1-216-833-11 METAL CHIP
10K
5%
R309
R310
1-216-845-11 METAL CHIP
1-216-839-11 METAL CHIP
100K
33K
5%
5%
R311
1-216-843-11 METAL CHIP
68K
5%
R312
1-216-843-11 METAL CHIP
68K
5%
1/10W
(GT800D)
1/10W
1/10W
(GT800D)
1/10W
(GT800D)
1/10W
R313
R314
R315
R318
R319
1-216-839-11
1-216-843-11
1-216-843-11
1-216-833-11
1-216-821-11
33K
68K
68K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
(GT805DX)
1/10W
1/10W
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
Remark
< RESISTOR >
R321
1-216-845-11 METAL CHIP
100K
5%
R101
R102
R103
R104
R105
1-216-077-11
1-216-049-11
1-216-821-11
1-216-829-11
1-216-841-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
1K
1K
4.7K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R322
R323
R325
R327
1-216-825-11
1-216-825-11
1-216-845-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
100K
220K
5%
5%
5%
5%
R106
R107
R108
R109
R110
1-216-841-11
1-216-073-00
1-216-073-00
1-216-833-11
1-216-833-11
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
47K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R328
R332
R333
R334
R335
1-216-849-11
1-218-871-11
1-216-809-11
1-216-841-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
10K
100
47K
33K
5%
0.5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R111
R112
R114
R115
R116
1-216-841-11
1-216-821-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
1K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R336
R337
R338
R339
R340
1-216-845-11
1-216-841-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
47K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
58
CDX-GT800D/GT805DX
MAIN
Ref. No.
Part No.
Description
Part No.
Description
R341
R342
R343
R344
R345
1-216-821-11
1-216-845-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
Ref. No.
R471
R472
R473
R474
R475
1-216-819-11
1-216-819-11
1-216-819-11
1-216-819-11
1-216-819-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
680
680
680
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R346
R347
R348
R350
R351
1-216-833-11
1-216-809-11
1-216-833-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R476
R477
R478
R479
R480
1-216-819-11
1-216-819-11
1-216-841-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R356
R357
R360
1-218-871-11 METAL CHIP
1-218-871-11 METAL CHIP
1-216-845-11 METAL CHIP
10K
10K
100K
0.5%
0.5%
5%
47K
0
1.5K
1K
0
1/10W
1/10W
5%
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
5%
5%
100K
1-216-841-11
1-216-864-11
1-216-823-11
1-216-821-11
1-216-864-11
1/10W
1-216-845-11 METAL CHIP
R481
R483
R484
R485
R487
5%
R361
R363
1-216-845-11 METAL CHIP
100K
5%
1/10W
1/10W
1/10W
(GT805DX)
1/10W
(GT800D)
1/10W
R364
R365
R366
R367
R372
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R488
R498
R501
R502
R504
1-216-864-11
1-216-864-11
1-216-821-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
0
0
1K
0
0
5%
1/10W
R373
R377
R380
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-809-11 METAL CHIP
100K
100K
100
5%
5%
5%
1-216-864-11
1-216-864-11
1-216-864-11
1-216-833-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
0
0
0
10K
5%
R552
1-216-821-11 METAL CHIP
1K
5%
R381
R382
1-216-825-11 METAL CHIP
1-216-825-11 METAL CHIP
2.2K
2.2K
5%
5%
1/10W
1/10W
1/10W
(GT800D)
1/10W
1/10W
R505
R521
R522
R551
1/10W
(GT800D)
1/10W
(GT800D)
R553
1-216-801-11 METAL CHIP
22
5%
R401
R402
R403
R404
R405
1-216-017-11
1-216-813-11
1-216-841-11
1-216-836-11
1-216-836-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47
220
47K
18K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R554
1-216-845-11
R555
R556
R557
1-414-813-11
1-414-813-11
1-216-864-11
1/10W
(GT800D)
METAL CHIP
100K
5%
1/10W
(GT800D)
FERRITE, EMI (SMD) (2012) (GT800D)
FERRITE, EMI (SMD) (2012) (GT800D)
SHORT CHIP
0 (GT800D)
R406
R407
R408
R409
R410
1-216-864-11
1-216-841-11
1-216-845-11
1-216-841-11
1-216-833-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
47K
100K
47K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R599
R610
R620
R621
R622
1-216-864-11
1-216-864-11
1-216-230-00
1-216-230-00
1-218-863-11
SHORT CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
METAL CHIP
0
0
22K
22K
4.7K
5%
5%
0.5%
1/8W
1/8W
1/10W
R411
R420
R423
R424
R429
1-216-833-11
1-216-839-11
1-216-813-11
1-216-825-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
33K
220
2.2K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R623
R624
R625
R626
R627
1-218-895-11
1-218-847-11
1-216-025-11
1-216-848-11
1-216-846-11
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
100K
1K
100
180K
120K
0.5%
0.5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R430
R431
R432
R433
R434
1-216-837-11
1-216-839-11
1-216-837-11
1-216-839-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
33K
22K
33K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R628
R629
R630
R631
R632
1-216-841-11
1-216-833-11
1-216-837-11
1-216-821-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
10K
22K
1K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R435
R436
R451
R452
R453
1-216-839-11
1-216-837-11
1-216-817-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
22K
470
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R633
R636
R637
R644
R654
1-216-821-11
1-216-864-11
1-216-839-11
1-216-296-11
1-216-846-11
METAL CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
1K
0
33K
0
120K
5%
1/10W
5%
1/10W
5%
1/10W
R454
R455
R461
R462
R470
1-216-817-11
1-216-817-11
1-216-809-11
1-216-809-11
1-216-819-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
100
100
680
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R655
R656
R657
R658
R659
1-216-848-11
1-216-845-11
1-216-813-11
1-216-049-11
1-218-863-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
180K
100K
220
1K
4.7K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
59
CDX-GT800D/GT805DX
MAIN
Ref. No.
SENSOR
SERVO
Part No.
Description
Remark
Ref. No.
R660
R661
R662
R663
R664
1-218-847-11
1-216-845-11
1-218-843-11
1-216-821-11
1-216-296-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
1K
100K
680
1K
0
0.5%
5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
X302
1-781-679-11 VIBRATOR, CRYSTAL (6MHz)
X551
1-813-173-11 VIBRATOR, CRYSTAL (8.664MHz) (GT800D)
X801
1-813-726-11 OSCILLATOR, CRYSTAL (11.2896MHz)
*************************************************************
Part No.
Description
Remark
R701
R702
R703
R704
R706
1-216-845-11
1-216-864-11
1-216-821-11
1-216-864-11
1-216-829-11
METAL CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
100K
0
1K
0
4.7K
5%
1/10W
SENSOR BOARD
**************
5%
1/10W
< SWITCH >
5%
1/10W
R707
R708
R709
R710
R711
1-216-829-11
1-218-899-11
1-218-873-11
1-218-236-11
1-218-236-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
150K
12K
1
1
5%
0.5%
0.5%
10%
10%
1/10W
1/16W
1/10W
1/4W
1/4W
R801
R802
R807
R808
R809
1-216-864-11
1-216-818-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
560
0
0
0
R810
R811
R812
R845
R851
1-216-864-11
1-218-871-11
1-218-871-11
1-216-821-11
1-218-871-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
R852
R853
R854
R855
R856
1-216-833-11
1-216-821-11
1-216-815-11
1-216-815-11
1-216-815-11
R857
R858
R859
R860
R861
SW2
1-529-566-61 SWITCH, PUSH (1 KEY) (SELF)
SW3
1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)
*************************************************************
A-1132-437-A SERVO BOARD, COMPLETE
**********************
< CAPACITOR >
5%
1/10W
C7
C10
C11
C12
C13
1-125-777-11
1-126-208-21
1-125-777-11
1-125-777-11
1-100-567-81
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
47uF
0.1uF
0.1uF
0.01uF
10%
20%
10%
10%
10%
10V
4V
10V
10V
25V
0
10K
10K
1K
10K
0.5%
0.5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
C14
C15
C16
C17
C18
1-104-609-11
1-125-777-11
1-162-964-11
1-125-777-11
1-125-777-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.001uF
0.1uF
0.1uF
20%
10%
10%
10%
10%
4V
10V
50V
10V
10V
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
330
330
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C19
C20
C22
C23
C24
1-125-777-11
1-164-677-11
1-164-677-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.033uF
0.033uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
16V
16V
10V
10V
1-216-815-11
1-216-821-11
1-218-871-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
330
1K
10K
0
0
5%
5%
0.5%
1/10W
1/10W
1/10W
C25
C26
C29
C30
C31
1-125-777-11
1-162-966-11
1-162-968-11
1-162-968-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.0022uF
0.0047uF
0.0047uF
0.1uF
10%
10%
10%
10%
10%
10V
50V
50V
50V
10V
R862
R863
R864
R868
R869
1-216-864-11
1-216-864-11
1-216-864-11
1-216-825-11
1-216-825-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
0
0
0
2.2K
2.2K
5%
5%
1/10W
1/10W
C32
C33
C36
C39
C40
1-125-777-11
1-125-777-11
1-125-777-11
1-126-208-21
1-126-395-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
0.1uF
0.1uF
0.1uF
47uF
22uF
10%
10%
10%
20%
20%
10V
10V
10V
4V
16V
R920
R921
R922
R929
1-216-073-00
1-216-073-00
1-216-845-11
1-216-837-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
10K
10K
100K
22K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
C41
C42
C43
C44
C45
1-125-777-11
1-125-777-11
1-100-567-81
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
25V
10V
10V
C46
C47
C48
C49
C50
1-162-923-11
1-164-245-11
1-100-567-81
1-125-777-11
1-100-567-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47PF
0.015uF
0.01uF
0.1uF
0.01uF
5%
10%
10%
10%
10%
50V
25V
25V
10V
25V
C51
C52
C53
C54
C55
1-125-777-11
1-125-777-11
1-125-777-11
1-100-567-81
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
25V
10V
C56
C58
1-164-245-11 CERAMIC CHIP
1-125-777-11 CERAMIC CHIP
0.015uF
0.1uF
10%
10%
25V
10V
< TRANSFORMER >
T620
1-443-879-11 TRANSFORMER, DC-DC CONVERTER
< THERMISTOR >
TH100
TH301
1-801-792-21 THERMISTOR, POSITIVE
1-810-812-21 THERMISTOR, NTC (1608)
< TUNER UNIT >
TUX501 A-3220-961-B TUNER UNIT (TUX-032)
< VIBRATOR >
X301
60
1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
CDX-GT800D/GT805DX
SERVO
Ref. No.
Part No.
Description
Part No.
Description
C60
C62
C66
C67
C68
1-162-964-11
1-125-777-11
1-100-567-81
1-100-567-81
1-100-567-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
50V
10V
25V
25V
25V
Remark
R30
R31
R32
R33
R34
1-218-989-11
1-218-989-11
1-218-947-11
1-218-990-81
1-216-864-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
1M
1M
330
0
0
5%
5%
5%
1/16W
1/16W
1/16W
C69
C70
C71
C72
C80
1-100-567-81
1-125-777-11
1-125-777-11
1-125-777-11
1-125-837-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
0.1uF
1uF
10%
10%
10%
10%
10%
25V
10V
10V
10V
6.3V
R35
R36
R37
R38
R39
1-162-961-11
1-218-947-11
1-218-947-11
1-218-941-81
1-218-941-81
CERAMIC CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
330PF
330
330
100
100
10%
5%
5%
5%
5%
50V
1/16W
1/16W
1/16W
1/16W
C132
C133
1-125-837-11 CERAMIC CHIP
1-125-837-11 CERAMIC CHIP
1uF
1uF
10%
10%
6.3V
6.3V
R40
R41
R42
R43
R44
1-218-941-81
1-218-941-81
1-218-977-11
1-218-961-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
100
100K
4.7K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R46
R47
R48
R52
R53
1-218-945-11
1-218-945-11
1-218-945-11
1-218-962-11
1-218-979-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
220
220
220
5.6K
150K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R54
R55
R57
R58
R60
1-218-990-81
1-218-973-11
1-218-967-11
1-218-969-11
1-218-941-81
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
47K
15K
22K
100
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R61
R62
R63
R64
R65
1-218-941-81
1-218-941-81
1-218-977-11
1-218-977-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
100
100K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R67
R68
R69
R70
R71
1-218-941-81
1-218-941-81
1-218-941-81
1-218-965-11
1-218-973-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
100
100
10K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R72
R73
R74
R75
R77
1-218-973-11
1-218-973-11
1-218-941-81
1-218-941-81
1-218-973-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
47K
47K
100
100
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R78
R79
R80
R81
R82
1-218-941-81
1-218-941-81
1-218-941-81
1-218-941-81
1-218-941-81
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R83
R84
R85
R86
R87
1-218-977-11
1-218-941-81
1-218-977-11
1-218-941-81
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
100
100K
100
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R88
R96
R97
R98
R132
1-218-990-81
1-218-941-81
1-220-200-81
1-218-971-11
1-218-969-11
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
100
30K
33K
22K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R133
R142
R143
1-218-953-11 RES-CHIP
1-218-990-81 SHORT CHIP
1-218-990-81 SHORT CHIP
5%
1/16W
< CONNECTOR >
CN1
CN2
1-691-380-61 CONNECTOR, FFC/FPC (ZIF) 16P
1-817-275-21 CONNECTOR, BOARD TO BOARD 28P
< JUMPER RESISTOR >
FB2
FB3
FB4
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
0
< IC >
IC1
IC2
IC3
IC6
6-707-327-01
6-708-729-01
6-806-019-02
6-708-728-01
IC
IC
IC
IC
BA5968FP-E2
TC94A70FG-002
MB90486BPFV-G-177E1
BH15LB1WG
< TRANSISTOR >
Q2
Q3
Q21
6-551-120-01 TRANSISTOR 2SA2119K
8-729-928-90 TRANSISTOR DTC114EE
8-729-904-87 TRANSISTOR 2SB1197K-R
< RESISTOR >
R1
R2
R5
R6
R8
1-218-965-11
1-218-977-11
1-218-969-11
1-218-969-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
100K
22K
22K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R9
R11
R12
R13
R14
1-218-965-11
1-218-941-81
1-218-969-11
1-218-969-11
1-218-929-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
100
22K
22K
10
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R15
R16
R18
R19
R20
1-218-929-11
1-218-953-11
1-218-941-81
1-218-935-11
1-162-961-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
CERAMIC CHIP
10
1K
100
33
330PF
5%
5%
5%
5%
10%
1/16W
1/16W
1/16W
1/16W
50V
R21
R22
R23
R24
R25
1-218-941-81
1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R26
R27
R28
R29
1-218-977-11
1-218-977-11
1-218-945-11
1-218-989-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
100K
220
1M
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
Ref. No.
Remark
1K
0
0
61
CDX-GT800D/GT805DX
SERVO
Ref. No.
R145
SUB PANEL
Part No.
Description
1-218-990-81 SHORT CHIP
Remark
Ref. No.
Part No.
Description
Remark
PARTS FOR INSTALLATION AND CONNECTIONS
***************************************
0
< SWITCH >
SW1
1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)
< VIBRATOR >
X1
1-813-678-11 OSCILLATOR, CERAMIC (CHIP TYPE) (12MHz)
X2
1-795-561-21 VIBRATOR, CERAMIC (16.9344MHz)
*************************************************************
SUB PANEL BOARD
****************
351
352
353
354
355
X-3382-647-1
1-776-207-72
3-246-471-01
2-639-542-01
X-3381-154-1
356
357
3-349-410-11 BUSHING (GT800D)
3-934-325-01 SCREW, +K (5X8) TAPPING
351
FRAME ASSY, FITTING
CORD (WITH CONNECTOR) (POWER)
KEY (FRAME)
COLLAR
SCREW ASSY (BS4), FITTING (GT800D)
352
353
< DIODE >
LED990 6-500-476-01 LED SML310BA1TT86 (DISC IN)
×2
< RESISTOR >
354
R990
1-216-821-11 METAL CHIP
1K
5%
1/10W
R991
1-216-821-11 METAL CHIP
1K
5%
1/10W
*************************************************************
MISCELLANEOUS
***************
12
51
52
0 203
204
1-776-207-72 CORD (WITH CONNECTOR) (POWER)
1-869-079-11 FLEXIBLE BOARD
1-790-355-54 CORD (WITH CONNECTOR) (RCA)
(SUB OUT (MONO))
8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP)
A-1075-645-A CHASSIS (OP) SUB ASSY (including M901)
F901
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
M902
A-3372-447-A MOTOR ASSY, SL (SLED)
M903
A-1075-643-A MOTOR ASSY, LE (LOADING)
SW4
1-571-099-11 SWITCH (1 KEY) (LIMIT)
*************************************************************
ACCESSORIES
************
1-479-077-23
1-479-077-43
2-548-729-01
2-663-779-11
REMOTE COMMANDER (RM-X152) (GT805DX)
REMOTE COMMANDER (RM-X154) (GT800D)
LID, BATTERY CASE (for RM-X152/X154)
MANUAL, INSTRUCTION, INSTALL (ENGLISH,
FRENCH,SPANISH) (GT805DX)
2-663-779-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
SPANISH,SIMPLIFIED CHINESE) (GT800D)
2-663-780-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH,
SPANISH) (GT805DX)
2-663-780-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH,
SIMPLIFIED CHINESE) (GT800D)
X-2103-370-1 CASE ASSY (for FRONT PANEL)
*************************************************************
62
355
356
357
×4
CDX-GT800D/GT805DX
MEMO
63
CDX-GT800D/GT805DX
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
64
Ver.
Date
1.0
2005.12
Description of Revision
New