Download Sony CDX-GT317EE, CDX-GT360

CDX-GT317EE/GT360
SERVICE MANUAL
Saudi Arabia Model
CDX-GT360
East European Model
Ver. 1.1 2007.03
CDX-GT317EE
(Photo: CDX-GT317EE)
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
CDX-GT262/GT217
CD Drive Mechanism Type
MG-101TA-188//Q
Optical Pick-up Name
DAX-25A
SPECIFICATIONS
CD player section
Signal-to-noise ratio
Frequency response
Wow and flutter
MW/LW (GT317EE)
Tuning range
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
MW: 30 µV, LW: 40 µV
120 dB
10 – 20,000 Hz
Below measurable limit
Tuner section
FM
Tuning range
MW/SW (GT360)
Tuning range
GT317EE:
FM1/FM2: 87.5 – 108.0 MHz
(at 50 kHz step)
FM3: 65 – 74 MHz (at 30 kHz step)
GT360:
87.5 – 108.0 MHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
MW: 531 – 1,602 kHz
SW1: 2,940 – 7,735 kHz
SW2: 9,500 – 18,135 kHz
(except for 10,140 – 11,575 kHz)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
Power amplifier section
Outputs
Speaker outputs (sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output
GT317EE: 50 W × 4 (at 4 ohms)
GT360: 52 W × 4 (at 4 ohms)
– Continued on next page –
FM/MW/LW COMPACT DISC PLAYER
CDX-GT317EE
FM/MW/SW COMPACT DISC PLAYER
CDX-GT360
9-887-460-02
2007C04-1
© 2007.03
Sony Corporation
eVehicle Division
Published by Sony Techno Create Corporation
CDX-GT317EE/GT360
General
Outputs
Inputs
Tone controls
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Audio outputs terminal (sub/rear switchable)
Power antenna relay control terminal
Power amplifier control terminal
Telephone ATT control terminal (GT317EE)
BUS control input terminal
BUS audio input terminal
Antenna input terminal
AUX input jack (stereo mini jack)
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
12 V DC car battery (negative ground)
Approx. 178 × 50 × 179 mm
(7 1/8 × 2 × 7 1/8 in.) (w/h/d)
Approx. 182 × 53 × 162 mm
(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d)
Approx. 1.2 kg (2 lb. 11 oz.)
Card remote commander: RM-X151
Parts for installation and connections (1 set)
Design and specifications are subject to change without
notice.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.
TEST DISCS
Please use the following test discs for the check on the CD section.
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical pickup block.
optical pick-up
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
semi-fixed resistor
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
CDX-GT317EE/GT360
This compact disc player is classified as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
• CD playback
You can play CD-DA (also containing CD TEXT*), CD-R/CDRW (MP3/WMA files also containing Multi Session .
Type of discs
Label on the disc
CD-DA
This label is located on the bottom of the chassis.
MP3
WMA
* A CD TEXT disc is a CD-DA that includes information such as
disc, artist and track name.
SOLDER
• UNLEADED
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CN350) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CN350
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
J-2502-076-1
SERVO BOARD
CN2
3
CDX-GT317EE/GT360
Ver. 1.1
NOTE FOR REPLACEMENT OF THE SERVO BOARD
When repairing, the complete SERVO board (A-1177-201-A) should
be replaced since any parts in the SERVO board cannot be repaired.
TABLE OF CONTENTS
1.
GENERAL
Location of Controls ........................................................ 5
Connections ..................................................................... 6
NOTE FOR REPLACEMENT OF THE AUX JACK (J901)
To replace the AUX jack requires alignment.
1. Insert the AUX jack into the KEY board.
2. Place the KEY board on the front panel.
3. Solder the three terminals of the jack.
KEY board
AUX jack
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
Sub Panel (FL) Assy ........................................................
CD Mechanism Block .....................................................
Main Board ......................................................................
Servo Board .....................................................................
Chassis (T) Sub Assy .......................................................
Roller Arm Assy ..............................................................
Chassis (OP) Assy ...........................................................
3.
DIAGNOSIS FUNCTION ........................................ 15
4.
DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
Block Diagram –Main Section– ......................................
Block Diagram –Display Section– ..................................
Printed Wiring Board –Main Section– ............................
Schematic Diagram –Main Section (1/3)– ......................
Schematic Diagram –Main Section (2/3)– ......................
Schematic Diagram –Main Section (3/3)– ......................
Printed Wiring Board –Key Section– ..............................
Schematic Diagram –Key Section– .................................
5.
EXPLODED VIEWS
11
11
12
12
13
13
14
17
18
20
21
22
23
24
25
5-1. Main Section .................................................................... 30
5-2. Front Panel Section ......................................................... 31
5-3. CD Mechanism Section (MG-101TA-188//Q) ................ 32
6.
front panel
4
ELECTRICAL PARTS LIST .................................. 33
CDX-GT317EE/GT360
SECTION 1
GENERAL
This section is extracted
from instruction manual.
• LOCATION OF CONTROLS
• CDX-GT317EE
Location of controls and basic operations
Main unit
12 3
4
5
6
7
8
OFF
PUSH SELECT
EQ3
SOURCE
AUX
SEEK
SEEK
L Receptor for the card remote
commander
MODE
PTY
DIM
ALBM
1
DSPL
2
REP
SHUF
3
4
PAUSE
5
6
AF/TA
CDX-GT317EE
9q; qa qs qdqfqg
qh
Card remote commander
RM-X151
1
4
qk
OFF
SOURCE
SEL
MODE
A OFF button
To power off; stop the source.
B EQ3 (equalizer) button 11
To select an equalizer type (XPLOD,
VOCAL, EDGE, CRUISE, SPACE,
GRAVITY, CUSTOM or OFF).
+
ws
wd
C Volume control dial/select button 11
To adjust volume (rotate); select setup items
(press and rotate).
wf
D SOURCE button
To power on; change the source (Radio/CD/
MD*1/AUX).
–
qf
SCRL
DSPL
1
4
2
3
5
6
E Disc slot
Insert the disc (label side up), playback
starts.
+
ql
qj
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
w;
wa
qd
ATT
VOL
–
K SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fastforward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
M MODE button 8, 12
To select the radio band (FM/MW/LW);
select the unit*2.
N DSPL (display)/DIM (dimmer) button
8, 9
To change display items (press); change the
display brightness (press and hold).
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 4).
qk < (.)/, (>) buttons
To control CD/radio, the same as (SEEK)
–/+ on the unit.
ql VOL (volume) +/– button
To adjust volume.
w; ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
wa SEL (select) button
The same as the select button on the unit.
ws M (+)/m (–) buttons
To control CD, the same as (1)/(2)
(ALBM –/+) on the unit.
O RESET button (located behind the front
panel) 4
wd SCRL (scroll) button 8
To scroll the display item.
P Number buttons
CD/MD*1:
(1)/(2): ALBM –/+*3*4
To skip albums (press); skip albums
continuously (press and hold).
(3): REP 8
(4): SHUF 8
(6): PAUSE*5
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
wf Number buttons
To receive stored stations (press); store
stations (press and hold).
Q AF (Alternative Frequencies)/TA
(Traffic Announcement) button 9
To set AF and TA in RDS.
When an MD changer is connected.
When a CD/MD changer is connected.
When an MP3/WMA is played.
If the changer is connected, the operation is
different, see page 13.
*5 When playing back on this unit.
*1
*2
*3
*4
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 15.
F Display window
G AUX input jack 12
To connect a portable audio device.
H Z (eject) button
To eject the disc.
I PTY (Program Type) button 10
To select PTY in RDS.
J
(front panel release) button 5
6
7
• CDX-GT360
Location of controls and basic operations
Main unit
12 3
4
5
6
7
8
OFF
PUSH SELECT
EQ3
SOURCE
AUX
SEEK
SEEK
BTM
L Receptor for the card remote
commander
MODE
DIM
ALBM
1
DSPL
2
REP
SHUF
3
4
PAUSE
5
6
SCRL
CDX-GT360
9q; qa qs qdqfqg
Card remote commander
RM-X151
1
4
qk
OFF
SOURCE
ATT
SEL
MODE
w;
wa
qd
+
ws
ql
SCRL
DSPL
1
2
3
4
5
6
+
VOL
–
qh
qj
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A OFF button
To power off; stop the source.
B EQ3 (equalizer) button 9
To select an equalizer type (XPLOD,
VOCAL, EDGE, CRUISE, SPACE,
GRAVITY, CUSTOM or OFF).
qj
C Volume control dial/select button 9
To adjust volume (rotate); select setup items
(press and rotate).
wd
D SOURCE button
To power on; change the source (Radio/CD/
MD*1/AUX).
–
qf
K SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fastforward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
E Disc slot
Insert the disc (label side up), playback
starts.
M MODE button 8, 11
To select the radio band (FM/MW/SW);
select the unit*2.
N DSPL (display)/DIM (dimmer) button
8
To change display items (press); change the
display brightness (press and hold).
O RESET button (located behind the front
panel) 4
P Number buttons
CD/MD*1:
(1)/(2): ALBM –/+*3*4
To skip albums (press); skip albums
continuously (press and hold).
(3): REP 8
(4): SHUF 8
(6): PAUSE*5
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
Q SCRL (scroll) button 8
To scroll the display item.
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 4).
qk < (.)/, (>) buttons
To control CD/radio, the same as (SEEK)
–/+ on the unit.
ql VOL (volume) +/– button
To adjust volume.
w; ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
wa SEL (select) button
The same as the select button on the unit.
ws M (+)/m (–) buttons
To control CD, the same as (1)/(2)
(ALBM –/+) on the unit.
wd Number buttons
To receive stored stations (press); store
stations (press and hold).
When an MD changer is connected.
When a CD/MD changer is connected.
When an MP3/WMA is played.
If the changer is connected, the operation is
different, see page 11.
*5 When playing back on this unit.
*1
*2
*3
*4
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 13.
F Display window
G AUX input jack 10
To connect a portable audio device.
H Z (eject) button
To eject the disc.
I BTM button 8
To start the BTM function (press and hold).
J
6
(front panel release) button 5
7
5
CDX-GT317EE/GT360
• CONNECTIONS
• CDX-GT317EE
Connection example
Notes (2-A)
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
A
Tip (2-B- )
For connecting two or more CD/MD changers, the source
selector XA-C40 (not supplied) is necessary.
AUDIO OUT REAR*
* AUDIO OUT SUB/REAR
B
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
Source selector*
*
XA-C40
BUS CONTROL IN
* not supplied
6
CDX-GT317EE/GT360
Source selector
(not supplied)
Supplied with the CD/MD changer
XA-C40
Supplied with XA-C40
XA-C40
*2
AUDIO OUT REAR*3
L
2
R
*1 from car antenna (aerial)
BUS AUDIO OUT
IN
REAR/SUB
Fuse (10 A)
BUS AUDIO IN
Blue/white striped
BUS
CONTROL IN
1
3
5
7
2
4
6
8
3
from the car’s speaker
connector
AMP REM
Max. supply current 0.3 A
Light blue
ATT
1
Purple
2
3
*1 Note for the aerial connecting
If your car aerial is an ISO (International
Organization for Standardization) type, use the
supplied adaptor 2 to connect it. First connect
the car antenna (aerial) to the supplied adaptor,
then connect it to the antenna (aerial) jack of the
master unit.
*2 RCA pin cord (not supplied)
*3 AUDIO OUT can be switched to SUB or REAR. For
details, see the supplied Operating Instructions.
+
–
+
Grey
4
–
Speaker, Rear, Right
Speaker, Rear, Right
Speaker, Front, Right
Speaker, Front, Right
5
White
6
7
Speaker, Front, Left
+
Speaker, Front, Left
–
Green
8
Speaker, Rear, Left
+
Speaker, Rear, Left
–
Negative polarity positions 2, 4, 6, and 8 have striped leads.
5
7
from the car’s power connector
*1
4
See “Power connection diagram” on the reverse
side for details.
*2
*3
4
5
Yellow
continuous power supply
Blue
power antenna (aerial) control
7
8
8
Red
switched power supply
Black
ground (earth)
Positions 1, 2, 3, and 6 do not have pins.
Connection diagram
A To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
B To the interface cable of a car telephone
Warning
If you have a power antenna (aerial) without a relay box,
connecting this unit with the supplied power connecting
lead 3 may damage the antenna (aerial).
Notes on the control and power suppy leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner, or when you activate the AF
(Alternative Frequency) or TA (Traffic Announcement) function.
• When your car has built-in FM/MW/LW antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power supply lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
7
CDX-GT317EE/GT360
• CONNECTIONS
• CDX-GT360
Connection example
Notes (2-A)
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
A
Tip (2-B- )
For connecting two or more CD/MD changers, the source
selector XA-C40 (not supplied) is necessary.
AUDIO OUT REAR*
* AUDIO OUT SUB/REAR
B
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
Source selector*
XA-C40
BUS CONTROL IN
* not supplied
8
CDX-GT317EE/GT360
Source selector
(not supplied)
Supplied with the CD/MD changer
Supplied with XA-C40
XA-C40
*1
BUS AUDIO IN
L
R
BUS AUDIO OUT
IN
REAR/SUB
from car antenna (aerial)
AUDIO OUT
REAR*2
Fuse (10 A)
BUS
CONTROL IN
*1 RCA pin cord (not supplied)
*2 AUDIO OUT can be switched SUB or
REAR. For details, see the Operating
Instructions.
Blue/white striped
2
3
AMP REM
Max. supply current 0.3 A
White
Black
Left
1
White/black striped
Gray
Blue
Right
ANT REM
Gray/black striped
Green
Max. supply current 0.1 A
Red
Left
4
Green/black striped
Purple
Right
Purple/black striped
2
Yellow
5
Connection diagram
1 To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow, and red power input leads.
2 To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
amplifier
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/MW/SWantenna (aerial)
in the rear/side glass, see “Notes on the control and power
supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
4 To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has a built-in FM/MW/SW antenna (aerial)
in the rear/side glass, see “Notes on the control and power
supply leads.”
5 To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power supply lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
9
CDX-GT317EE/GT360
Ver. 1.1
SECTION 2
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
SET
2-1.
SUB PANEL (FL) ASSY
(Page 11)
2-2.
CD MECHANISM BLOCK
(Page 11)
2-3.
MAIN BOARD
(Page 12)
2-4.
SERVO BOARD
(Page 12)
2-5.
CHASSIS (T) SUB ASSY
(Page 13)
2-6.
ROLLER ARM ASSY
(Page 13)
2-7.
CHASSIS (OP) ASSY
(Page 14)
1. CHUCKING ARM SUB ASSY
(SUPPLEMENT-1 Page 1)
2. SLED MOTOR ASSY
(SUPPLEMENT-1 Page 2)
3. OPTICAL PICK-UP SECTION
(SUPPLEMENT-1 Page 3)
4. OPTICAL PICK-UP
(SUPPLEMENT-1 Page 3)
10
CDX-GT317EE/GT360
Note: Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL (FL) ASSY
3 two claws
2 two claws
1 two screws
(+PTT 2.6 × 6)
4 sub panel (FL) assy
2-2. CD MECHANISM BLOCK
7 CD mechanism block
6 bracket (CD)
5 two screws
(+PTT 2.6 × 4)
3
2 screw
(+PTT 2.6 × 6)
4 CN350
1 screw
(+PTT 2.6 × 6)
11
CDX-GT317EE/GT360
2-3. MAIN BOARD
2 two screws
(+PTT 2.6 × 8)
5 screw
(+PTT 2.6 × 10)
4 two screws
(+P 2.6 × 8)
6 two screws
(+PTT 2.6 × 10)
1 three screws
(+BTT 2.6 × 5)
7 screw
(+P 2.6 × 10)
8 screw
(+PTT 2.6 × 10)
9 heat sink
0 MAIN board
3
insulating sheet
2-4. SERVO BOARD
WHT
RED
BLK
WHT
RED
BLK
RED
ORG
BLE
YEL
GRY
2 toothed lock screw
(M 1.7 × 2.5)
3 toothed lock screw
(M 1.7 × 2.5)
SERVO board
5 SERVO board
1 Remove the eleven solders.
4 optical pick-up (16 core)
(CN1)
claw
claw
12
CDX-GT317EE/GT360
2-5. CHASSIS (T) SUB ASSY
2 two precision screws
(+P 1.7 × 2.2)
1 two precision screws
(+P 1.7 × 2.2)
4 chassis (T) sub assy
3 claw
2-6. ROLLER ARM ASSY
5 roller arm assy
4 gear (RA1)
1 spring (RAL)
3 washer
2 spring (RAR)
13
CDX-GT317EE/GT360
Ver. 1.1
2-7. CHASSIS (OP) ASSY
6 chassis (OP) assy
1 tension spring (KF)
5
7 coil spring (damper) (natural)
8 coil spring (damper) (green)
4 slider (R)
3 lever (D)
2 gear (LE1)
14
CDX-GT317EE/GT360
SECTION 3
DIAGNOSIS FUNCTION
Description of the Diagnostics function:
4. Contents of each display mode
4-1. Reset count display mode
1. Setting the Diag display mode
With the power off, press the [4] button, [5] button, and [4] button
on the set body or the remote control (for more than 2 seconds)
in turn.
2. Canceling the Diag display mode
During the Diag function mode, press the [OFF] button.
3. Initial display in the Diag display mode.
Just when the Diag mode is entered, “reset count” is displayed.
The display mode is switched by each rotation of
SEEK +/M > or SEEK – /. m keys.
XX
Reset count
(in hexadecimal format)
Diag code
01: Reset count
4-2. Reset count by watchdog timer display mode
02
XX
Reset count
(in hexadecimal format)
Reset count display
01
01
Diag code
02: Number of resets by watchdog timer
XX
4-3. Number of connected units display mode
Reset count by watchdog timer display
02
XX
Number of connected units display
031
XXX
031
XXX
Show the number of connected units for
CD-C, MD-C and XM respectively from
the rightmost (in hexadecimal format).
Recency of information
1-3: 1 represents the latest.
Diag code
03: Number of connected unit.
Operating hours display
04
XXXX
The display mode is switched by each rotation of [2/ALBM+] or
[1/ALBM--] keys during the number of connected units display mode.
CD error information display
051
No. of connected units history 1 (latest) display
XX
031
OFFSET/FAILURE error display
XXX
No. of connected units history 2 display
061XXXXX
032
XXX
No. of connected units history 3 display
033
XXX
4-4. Operating hours display mode
04
XXXX
Operating hours
(in hexadecimal format)
Diag code
04: Operating hours
15
CDX-GT317EE/GT360
4-5. CD error information display mode
4-5-1. Error description
4-6. OFFSET/FAILURE error display mode
061XXXXX
051
XX
Error information
Error description Indication
Description
(in hexadecimal
1X
SERVO ERROR
format)
3X
LOADING ERROR
Recency of information
4X
TRACK JUMP
1-3: 1 represents the latest.
5X
TEXT ERROR
Diag code
FX
MECHA
ERROR
05: CD error information
Operating hours
Error description
(0: OFFSET, 1: FAILURE)
Recency of information
1-3: 1 represents the latest.
Diag code
06: OFFSET/FAILURE
The display mode is switched by each rotation of [2/ALBM+] or
[1/ALBM--] keys during the OFFSET/FAILURE error display mode.
4-5-2. Disc type and operating hours
051XXXXX
OFFSET/FAILURE error history 1 (latest) display
Disc type
Operating hours
Disc type
Recency of information
1-3: 1 represents the latest.
Diag code
05: CD error information
Indication
0
1
2
3
8
F
Disc type
MP3
WMA
AAC
ATRAC
CD/DA
UNKNOWN
The display mode is switched by each rotation of [2/ALBM+] or
[1/ALBM--] keys during the CD error information display mode.
061XXXXX
OFFSET/FAILURE error history 2 display
062XXXXX
OFFSET/FAILURE error history 3 display
063XXXXX
CD error info history 1 (latest)
Error description plus error details display
051
XX
CD error info history 1 (latest)
Disc type plus operating hours display
051XXXXX
CD error info history 2
Error description plus error details display
052
XX
CD error info history 2
Disc type plus operating hours display
052XXXXX
CD error info history 3
Error description plus error details display
053
XX
CD error info history 3
Disc type plus operating hours display
053XXXXX
16
CDX-GT317EE/GT360
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM — MAIN SECTION —
J652 (1/2)
ELECTRONIC VOLUME
IC401
L
BUS
AUDIO
IN
R
J652 (2/2)
BUS-RCH
CD L
CD R
CD-RCH
6 CD-LCH
5 CD-RCH
AUX-RCH
9 AUX-LCH
7 AUX-RCH
CD-RCH
CDON
CDMON
ZMUTE
CD ON
CDM ON
Z MUTE
TU-RCH
4 TU-LCH
3 TU-RCH
B/U CHECK
B/U CHECK
I2C BUS CONTROLLED POWER AMP/
MULTIPLE VOLTAGE REGULATOR
IC300
OUT-RL 23
11 IN RL
R-CH(FRONT)
R-CH(REAR)
MUTE
Q440
DR+6V
MECHA+6V
BU+3.3V
SCL
SDA
MUTE CONTROL
SWITCH
Q491,492
2
A ATT
D491
4
FR+
12
FR–
3
RR+
11
RR–
R-CH
BATT
5
AMP-REM
6
ANT-REM
D493
F901
16
VP 35
SERVO+3.3V
D+3.3V
SYSTEM CONTROL
IC501 (1/2)
AUX R-CH
CDMON
CDON
ZMUTE
AUX
92 CDMON
91 CDON
61 Z MUTE
TU1
(TUNER UNIT)
I2C SCK 33
I2C SIO 34
2 SDA
4 SCL
SCL
SDA
16 BEEP
22 STB
25 DIAG
ATT 100
BATT
BATT
SDA
SCL
VOLATT 9
RL+
RL–
10
AMP REM 29
ANT REM 27
BU+3.3V
A+3.3V
CN300
1
FL+
9
FL–
OUT FL+ 5
OUT FL– 3
OUT RL+ 9
OUT RL– 7
MUTE
Q470
UNICLK
UNI CLK
J901
12 IN FL
SCL 29
SDA 30
LINKOFF
UNISO
UNISI
LINK OFF
UNI SO
UNI SI
MUTE
Q432
AUDIO OUT
REAR
R
R-CH
MUTE 28
BUSON
BUS ON
R-CH
OUT-FR 26
OUT-RR 24
A ATT
A ATT
L
SUBOUT-L 21
SUBOUT-R 22
OUT-FL 25
SYSRST
SYS RST
CD
MECHANISM
UNIT
(MG-101TA)
BUS-RCH
2 BUS-LCH
1 BUS-RCH
AUDIO+B
BU+B
SERVO3.3V
MECHA6V
PANEL+B
30
37
31
33
34
AUDIO+8.3V
BU+5V
SERVO+3.3V
MECHA+6V
PANEL+B
BEEP 5
L-CH 4
1 ANT R-CH 3
TUNER+5V
REG
Q3
E2PVDD 15
BU+3.3V
ACCIN 99
GT317EE
AUDIO+8.3V
BU+5V
39 VSM
12 TUATT
E2P SCL 16
E2P SDA 17
25 EEP CKO
24 EEP SIO
96
60
54
58
UNISO 59
12
11
10
8
9
BUSON
UNISCK
BUIN
UNISI
BUS IN
CLK IN
B/U-C
DATA OUT
DATA IN
13 NSMASK
SYSRST 88
TEST
TH400
D602
BATT
BATT
7
BUS ON 1
38 QUALITY
53 TU ATTIN
4
5
6
BUS ON
SWITCH
Q601
1
2
3
CNJ400
BUS
CONTROL IN
8
RST 2
SYSRST
RDS DEMODULATOR
IC50
SCL
SDA
LINK OFF
SWITCH
Q600
LINKOFF
• R-CH is omitted due to same as L-CH.
• Signal Path
: CD PLAY
: FM
16 MPX
INTN 15
9 XTI
BATTERY
CHECK
Q605
CLK 4
DATA I/O 6
13 RST
D353
QUALITY 5
MUTE CON 8
SCL 11
SDA 12
BATT 3
D609
NOISE MASK
SWITCH
Q1
10 XTO
TEL ATT
15
BUS INTERFACE
IC601
S-METER 6
TU MUTE 7
X50
8.664MHz
ACC
13
TESTIN 97
SCL
SDA
RDS OUT 9
7
ACCESSORY CHECK
Q702
TELEPHONE ATTENATION
CHECK
Q701
TELATT 98
BU+3.3V
REG
IC681
UNISI
B/U CHECK
UNICLK
BUSON
TU-SCL 13
TU-SDA 14
DIAG 7
AUDIO+8.3V
VCC 10
VDD+5V 11
AMPSTB 8
TU-RCH
UNISO
J1
(ANTENNA)
VDDA 1
VDDD 7
56 DAVN
RDS+3.3V
SWITCH
Q50
: MW/LW/SW
BU+3.3V
RESET
A
DISPLAY
SECTION
(Page 18)
26 RDS ON
GT317EE
CDX-GT317EE/GT360
17
17
: AUX
CDX-GT317EE/GT360
4-2. BLOCK DIAGRAM — DISPLAY SECTION —
FL901
FLUORESCENT
INDICATOR TUBE
SYSTEM CONTROL
IC501 (2/2)
GRID1 20
41 KEYIN0
KEY MATRIX
LSW901,902
S901–904,906–915
40 KEYIN1
D503
KEY ACKNOWLEDGE
SWITCH
Q664
RE901
PUSH SELECT
(VOLUME)
ROTARY
ENCODER
GRID2 19
FL SO 28
FL SCK 29
FL CS 27
14 DIO
12 CLK
10 CS
GRID3 16
52 KEYACK
17
3G •
18
48 AD ON
6
2G •
42
31 RE-IN0
32 RE-IN1
1G 41
FL DRIVE
Q883
FL DRIVE
Q882
FL DRIVE
Q881
RESET 15
PANEL+B
VH 9
FL VH+12V
VDD+3.3V
REG
IC972
VDD(+3.3V) 5
62 NOSESW
FL VH+12V
PANEL+B
PANEL+B
REMOTE CONTROL
SIGNAL RECEIVER
IC971
64 SIRCS
XOUT 80
XIN 79
MAIN
SECTION
OSCOUT 83
A
RESET
OSCIN 82
(Page 17)
FL+3V
REG
IC202
1
F+ •
2
X502
32.768kHz
D204-206
FL+7V
REG
IC201
D200-203
FL+12V
REG
IC200
D207
BATT
44
F– •
45
X501
18.432MHz
FL VH+12V
FL+12V
REG
IC203
BU+3.3V
FL ON 87
RESET
IC602
77 RESET
PANEL+B
GT317EE
GT360
S103
RESET
LED841–847,
850–857,
861–864
CDX-GT317EE/GT360
18
18
LED941–947,
950–957,
961–963
LSW901,902
CDX-GT317EE/GT360
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
— MAIN Board —
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
1
For schematic diagrams.
For printed wiring boards.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f
: internal component.
• C : panel designation.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
a
: Through hole.
•
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
•
•
•
•
•
•
•
•
A : B+ Line.
B : B– Line.
H : adjustment for repair.
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
) : MW/LW/SW
<
> : CD PLAY
∗ : Impossible to measure
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
Circled numbers refer to waveforms.
Signal path.
J : CD PLAY
F : FM
f : MW/LW/SW
L : AUX
• Semiconductor Location
(MAIN Board)
• Waveforms
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
IC501 i; (XOUT)
0.8 Vp-p
32.768 kHz
0.2 V/DIV, 20 µsec/DIV
2
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
IC501 is (OSC IN)
0.9 Vp-p
C
Q
18.432 MHz
These are omitted
B E
0.5 V/DIV, 0.1 µsec/DIV
3
IC50 9 (XTI)
BE C
These are omitted
1.1 Vp-p
8.664 MHz
ECB
0.5 V/DIV, 0.1 µsec/DIV
These are omitted
CDX-GT317EE/GT360
19
19
Ref. No.
D2
D101
D103
D104
D105
D106
D108
D109
D110
D111
D112
D113
D153
D200
D201
D202
D203
D204
D205
D206
D207
D301
D302
D303
D304
D305
D306
D307
D308
D309
D310
D311
D312
D353
D491
D493
D502
D503
D602
D603
D604
Location
F-3
I-4
I-3
I-3
I-3
I-3
I-3
I-4
I-4
I-4
I-4
I-4
I-2
H-10
H-10
H-10
I-10
I-9
I-9
I-9
G-10
C-8
D-8
C-9
D-9
C-6
C-6
C-6
C-6
C-7
C-7
C-8
D-7
G-8
E-5
E-6
H-7
I-6
D-10
D-10
E-10
Ref. No.
D605
D606
D607
D609
D702
D703
D704
D901
D998
D999
Location
D-10
D-10
D-10
F-9
C-8
C-9
C-9
B-10
C-9
B-8
IC50
IC200
IC201
IC202
IC203
IC300
IC401
IC501
IC601
IC602
IC681
H-2
G-11
I-10
I-7
H-9
B-6
D-3
G-6
E-10
G-8
D-6
Q1
Q3
Q50
Q420
Q432
Q440
Q452
Q460
Q470
Q491
Q492
Q600
Q601
Q605
Q664
Q701
Q702
E-2
F-3
H-2
B-4
B-3
B-4
B-3
C-4
C-4
E-6
E-6
E-10
E-10
D-10
I-6
C-9
C-8
CDX-GT317EE/GT360
4-3. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 19 for Semiconductor Location.
2
1
3
4
5
: Uses unleaded solder.
6
7
8
9
10
11
12
13
14
J652
L
R
C301
C309
IC300
F901
D103
D106
D104
JW4
D110
D112
JW5
JW7
JC25
D113
C154
(CHASSIS)
R709
R702
YEL
C705
C702
C703
D311
JW105
C405
C417
C412
C418 C419
IC601
JW106
JW95
JC33
JW110
JW108
L405
C415
C409
C315
C316
JW92
JC3
JC2
JW86
R600
JW90
C204
D503
JW88
R561
R205
JC23
R206
D207
IC200
R201
1
IC203
5
D202
D206
D205
1
R210
D201
JW80
JW109
JW68
JW67
C314
R533
1
R200
C206
R208
D203
C202
1
R202
IC201
R203
R204
5
D204
IC202
5
21
R207
S103
J
YEL
JW64
JW65
JW63
JW62
JW61
R532
R517
JC16
R673
FMB3
C201
JW93
JW89
JC26
D105
Q664
JC41
JW3 C155
C152
R671
D111
JW6
R152
R153
L151
D153
R154
JW2
JW1
I
D109
C502
R502
D101
D108
R570
C200
JW94
5
JW111
C151
C153
C514
R529
JC37
D353
R211
JW84
C512
CD
MECHANISM
UNIT
(MG-101TA)
R553
R209
D502
JW82
R504
R505
C501
R351
R519 JC17
R672
R522
R521
C513
R503
R155
R151
C313
R674 C519
JC15
JW18
JW17
C60
JW16
JC27
L406
X501
JW22
R520
IC602
3
2
4
1
L501
C507
IC501
JW19
R58
C57
JW8
JW20
L50
JW15
C56
R523 R512
C510
JW83
R558
Q50
R510
JW21
JW14
C55
C61
H
L3
IC50
X50
JW13
C54
R57
R54
L5
R53
JC13
R524
JC28
L2
R52
R511
R525
C52
C53
R509
C509
JW12
C50
R560
JW11
JW9
R15
C51
JW10
C58
R557
R556
JC40
C504
G
R610
JC36
D609
CN350
GT360 GT317EE
JW85
JW25
Q601
JW107
GT317EE
JW91
R544
FMB4
R539
GT360
JW28
JW79
R552
R526
JC4
JW26
JW23
R537
JC38
R612
Q600
R401
C402
R550
JC20
R611
R615
R608
R601
JC35
TH400
L410
C401
R538
JW29
JW81
JW30
R602
JC34
R402
JW78
X502
JW113
JW27
GT317EE
R55
D307
JW66
JC1
R551
C205
L4
R7
GT360
R507
R549
JC24
R6
R573
R302
R616
D604
C601
L402
R603
D602
R607
R568
L409
R604
Q605
R606
JC19
JW77
R567
C8
C319
JW100
R555
L401
R540
JW31
JW112
R534
C7
R565
C5
D606
L407
L403
JW76
GT317EE
D603
JW96
JC18
GT360
L300
JW103
C403
C318
JW32
BATT
D304
R636
JW75
JC14
R13
D303
D301
D702
JW74
C363
JC12
JW24
D2
C704
D605
JW73
R301
JW34
JC21
Q702
R708
R707
JW98
R563
JW72
JW35
D703 C701
JW71
GT360 R566
JW33
C600
D607
GT317EE
R564
JW70
Q492 R531
D493
C317
JW37
F
JW69
D491
Q3
C6
JW102
JW87
JW44
Q491
JW36
R12
C682
L901
L1
C2
JW60
JW58
C683
C491
R491
JW42
R10
Q701
JW97
C364
C3
C681
C306
R451
JW45
JC8
4
JW99
JC32
JW43
JW41
R9
JW40
JW39
JC5
R5
D310
C508
C431
Q1
GT317EE
R8
JW57
C308
C471
R471
R431
R3
R2
R706
IC681
JW46
C451
C1
R430
JC42 R485
R4
JW56
R481
IC401
C461
JW38
C15
R452
R1
E
R440
R470
R703
R705
R461
GT317EE
D998
D302
C622
R420
R460
5
JW101
D312
JW47
6
C997
L902
C365
C366
C484
C361
GT360
D306
JC7
C362
TU1
D305
C485
C486
D
C623
R355
R356
JW55
JC9
JC6
R704
C312
C473
C472
R472
JW48
1
JC22
GT317EE D704
D309
Q470
C
JW54
C463
C454
D308
C462
C320
JW59
Q460
R701
JW53
C302
C303
R462
2
7
JW49
C434
JW52
JC10
3
8
JW104
Q452
Q432
C305
C207
R357
C441
JC11
R358
R447
R448
R421
R442
C432
C421
C414
C307
C452
C998
JW51
C413
ATT
C304
JW50
D200
C325
C329
Q440
Q420
CN300
YEL
C330
D901
C423
R450 R449
C203
C426
D999
C445
C443
B
GT317EE
CNJ400
(BUS CONTROL IN)
-4
JC30
-3
JC29
-2
JC31
R
-1
C444
L
C424
J1
(ANTENNA)
A
AUDIO OUT
REAR
BUS
AUDIO IN
CN370
S103
RESET
X501
(Page 24)
CDX-GT317EE/GT360
20
20
1-871-263-
(21)
CDX-GT317EE/GT360
4-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 26 for IC Block Diagrams.
C303
C302
JC29
C325 C444
JC30
C330
C424
L901
C308
C306
C304
C301
JC31
C309
IC B/D
C305
C307
C317
IC300
R302
C319
C318
C434
JC12
R709
C320
C312
C313
C315
JC13
D304
D303
D306
D305
D307
C997
D308
D998
D309
C998
D310
D999
D704
D311
R705
D312
R701
C314
D301
C454
C316
R301
D302
CN300
D702
D703
F901
D607
JC33
C701
R703
R702
C704
L902
JC32
Q701
R704
L300
R491
C705
D491
JC8
JC9
IC602
R707
Q492
Q702
R706
C702
C703
(Page 22)
IC681
Q491
D493
R708
JC1
R604
R608
D602
Q600
C600
Q605
R610
C601
R612
CNJ400
JC22
JC21
R611
R616
D901
C329
R531
D603
Q601
TH400
R607
R602
R601
JC36
R606
D605
D604
D606
JC20
R615
IC B/D
C683
R600
R603
IC601
D609
(Page 23)
CDX-GT317EE/GT360
21
21
C682
C681
C491
C622
C623
CDX-GT317EE/GT360
• Refer to page 19 for Waveforms.
4-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 26 for IC Block Diagrams.
J652
J1
C445
C426
C463
C443
C423
C462
C473
C472
C362
C361
C452
Q470
Q460
Q420
Q440
C432
Q452
C413
C414
Q432
TU1
Q1
R3
R1
C15
R2
JC11
R357
JC10
R4
C1
R358
R5
R355
R472
R471
R448
R462
R461
C471
R447
R449
JC6
R442
R421
R451
C441
C461
R9
R8
JC5
C365 C366
R431
C3
Q3
L1
C431
C451
C421
R356
R450
JC7
C2
R10
C7
C5
C6
IC B/D
D2
IC401
R13
C486
R12
C8
C485
L4
R6
C484
R7
R420
R481
C58
R440
R460
R15
R470
R452
JC42
(Page 21)
C364
IC B/D
C363
L5
R55
R430
L5
C50
C51
R485
C52
C53
R53 C55
Q50
L50
R52
R57
R558
L2
R54
C60
R58
C57
X50
C54
IC50
C61
C56
L3
JC28
IC B/D
IC B/D
IC B/D
IC203
IC B/D
IC200
D113
IC201
IC202
CN370
JC41
D207
R208 R211
C207
C200
D101
D112
R205
R204
R203
C201
D201
R209
C206
R202
R200
R201
D200
C203
D203
D202
JC25
JC26
R207
D204
D206
D205
C202
R206 R210
D109
D108
D103
C205
C204
D111
D110
D105
D104
D106
D153
C151
(Page 23)
CDX-GT317EE/GT360
22
22
R151
C152
R154
C153
R155
R153
L151
C154
R152
C155
(Page 25)
CDX-GT317EE/GT360
• Refer to page 19 for Waveforms.
4-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 28 for IC Pin Description of IC501.
(Page 22)
(Page 21)
C509
R553
R529
R672
X502
C508
JC19
R561
R517
JC24
Q664
R570
C507
R568
JC37
R519
R533
JC2
R532
R674
C519
D502
JC17
JC16
CN350
X501
R565
C403
JC34
R555
C412
R509
JC35
L407
L501
C417
L409
L401
C405
L403
L405
R567
L402
R402
C510
R526
C419
D503
C502
L410
C409
C415
R671
R401
C418
R673
JC23
R539
R505
R503
JC3
L406
IC501
R540
JC18
R351
R502
R636
C512
R564
R504
C501
R563
C401
C514
JC15
C513
R522
C402
R521
R520
R523
R524
R560
23
JC4
R510
R512
JC27
C504
R511
R557
CDX-GT317EE/GT360
23
R556
JC14
JC38
R534
R552
R537
R551
R507
R538
R573
R550
R549
JC40
R544
R566
D353
S103
R525
CDX-GT317EE/GT360
4-7. PRINTED WIRING BOARD — KEY SECTION —
LED861-864,961-963
(RING ILLUMINATION)
R943
10
11
12
R961
13
LED841,941,
S901
R942
GT317EE
LED842
GT317EE
LED841
S901
LED842,942
(CD INDICATOR)
R842
GT360 LED942
GT360
S903
GT317EE
R962
GT360
LED863
R861
GT317EE
9
LSW901
R947
GT317EE
R906
R907
R908
IC971
D
S909
S910
LED851,951,
S909
1/ALBM–
LED852,952,
S910
2/ALBM+
S911
GT317EE
LED847,947, LED850,950,
S908
S907
MODE
DSPL/DIM
S912
R954
LED957
LED857
GT360 GT317EE
GT317EE
R853
11
R953
S915
S914
GT317EE
1-871-262-
GT360
LED856,956
S914
6/PAUSE
LED855,955
S913
5
LED854,954,
S912
4/SHUF
LED956
LED856
R854
GT360
S913
GT317EE
GT317EE
LED853,953,
S911
3/REP
GT317EE
GT360
GT360
LED955
LED855
R909
LED954
GT360
GT360
GT360
LED854
S908
2
3
GT360
GT360
GT317EE
LED953
GT360
GT317EE
S907
LED853
LED864
GT317EE
LED952
GT360 LED947
LED847
C974
IC971 R977
1
4
LED852
GT360
LED962
GT360
LED951
LED851
LED963
LED850
GT317EE
LED945
LED845
S906
LED845,945,
S906
PTY
LED862
GT317EE
GT360
8
GT360 LED941
GT360 GT317EE
LED946
R843
LED944
LED844
LSW902
GT317EE
SEEK–
C
GT360
LED961 GT317EE
LED861
R862
LSW902
S904
B
LED844,944,
S904
EQ3
7
LED846,946,
S903
SOURCE
LSW901
M>
SEEK+
R903 GT360
R904
6
R941
S902
5
LED950
OFF
4
R841
LED843 GT317EE
LED843,943,
LED943
GT360
S902
R902
A
3
LED846
2
1
: Uses unleaded solder.
(11)
LED857,957,
S915
AF/TA (GT317EE)
SCRL (GT360)
MAIN BOARD CN370
(Page 20)
A
CN901
GT317EE
3
GT317EE
R881
Q883
D908
R889
R882
FB901
IC972 C976
R978
D906
C982 C981
R883
FB902
D907
R886
D882
R887
38
R885
D903 FB903
D905
R988
4
R884
R983
R971
J901
AUX
C975
R989
5
R901
D904
Q881 Q882
R982 R888
R948
C904
GT360
R946
RE901
C992
FB904
R914
R915
FL901 FLUORESCENT INDICATOR TUBE
C977
R864
GT317EE
F
C991
R863
R846
2
GT360 GT317EE
R952
R852
R913
R951
R911
R950
R850
R910
R912
GT317EE
R845
1
R945
R844
R944
R975
GT360
R922
GT317EE GT360
R905
R949
R849
R976
D971
R921
GT360
GT317EE
R851
GT360
E
R981
G
RE901
PUSH SELECT
(VOLUME)
11
1-871-262-
• Semiconductor Location
Ref. No.
Location
D882
D903
D904
D905
D906
D907
D908
D971
F-7
F-10
F-9
F-10
F-10
F-10
F-10
E-4
IC971
IC972
C-4
F-10
LED841
LED842
A-12
B-7
CDX-GT317EE/GT360
24
24
Ref. No.
LED843
LED844
LED845
LED846
LED847
LED850
LED851
LED852
LED853
LED854
LED855
LED856
LED857
LED861
Location
A-1
B-2
C-2
B-4
C-4
C-5
C-6
C-6
C-7
C-8
C-9
C-10
C-11
B-3
Ref. No.
LED862
LED863
LED864
LED941
LED942
LED943
LED944
LED945
LED946
LED947
LED950
LED951
LED952
LED953
Location
B-2
B-3
C-3
A-12
B-7
A-1
B-2
C-2
B-4
C-4
C-5
C-5
C-6
C-7
Ref. No.
LED954
LED955
LED956
LED957
LED961
LED962
LED963
Location
C-8
C-9
C-10
C-10
B-3
C-3
C-2
Q881
Q882
Q883
F-8
F-8
F-9
(11)
CDX-GT317EE/GT360
4-8. SCHEMATIC DIAGRAM — KEY SECTION —
R981
R978
R941
R943
R841
LED946
R843
LED846
R949
R947
R951
R849
R851
R953
LED961
R853
LED861
C976
LED863
C977
R942
LED944
R842
LED844
R945
LSW901(1/2)
R845
LED950
LED953
LED850
LED853
LED957
LED857
R961
R861
R982
R863
LED941
LED841
R944
R946
R844
R846
LED951
R948
LED851
R952
R954
R852
LED862
R962
R854
C975
IC972
R864
LED942
LED945
LED842
LED947
LED845
LED847
LSW902(1/2)
R950
LED954
R850
LED854
LED956
LED856
LED962
R862
R975
LED864
R976
LED943
LED952
LED843
LED955
LED852
R977
LED963
LED855
IC971
D971
C974
C992
C991
C982
CN901
D908
R886
R922
R901
R971
R902
R903
R921
Q883
RE901
D904
R889
R887
R983
R888
C904
FB904
R905
R904
D882
R988
R884
D903
R882
R907
R908
R909
R910
R911
R912
R913
R914
R915
S908
S909
S910
S911
S912
S913
S914
S915
LSW902(2/2)
LSW901(2/2)
D907
D906
D905
R906
S907
Q881
(Page 22)
C981
Q882
S906
S904
S903
S902
S901
R885
R883
R881
FB903
FB901
FB902
FL901
J901
CDX-GT317EE/GT360
25
25
R989
CDX-GT317EE/GT360
• IC BLOCK DIAGRAMS
IC300 TDA8588AJ/N2/R1 (MAIN Board (1/3))
IC601 BA8271F-E2 (MAIN Board (1/3))
TAB 1
2 SDA
OUT-FL- 3
BUS ON 1
BUS ON
SWITCH
RST 2
RESET
SWITCH
BATT 3
BATTERY
SWITCH
14 VCC
I2C BUS
4 SCL
FL
OUT-FL+ 5
6 VP2
OUT-RL- 7
RL
MUTE
10 SVR
PROTECTION/
DIAGNOSTIC
IN-RR 15
CLK 4
VREF 5
DATA 6
9 DATA IN
GND 7
8 DATA OUT
12 IN-FL
14 IN-FR
MUTE
S-GND 13
RESET
BUS ON
CLK IN
BU IN
8 PGND3
OUT-RL+ 9
IN-RL 11
13
12
11
10
16 BEEP
VP
OUT-RR+ 17
18 PGND2
RR
OUT-RR- 19
20 VP1
OUT-FR+ 21
FR
OUT-FR- 23
STANDBY/
MUTE
22 STB
CHIP DETECT/
DIAGNOSTIC
24 PGND1
BATTERY
DETECTION
DIAG 25
TEMPERATURE
PROTECTION
IC200
IC201
IC202
IC203
ENABLE
LOGIC
26 RST
ANT-REM 27
SWITCH
AMP-REM 29
SWITCH
NJM2387ADL3 (MAIN Board (2/3))
NJM2387ADL3 (MAIN Board (2/3))
NJM2387ADL3 (MAIN Board (2/3))
NJM2387ADL3 (MAIN Board (2/3))
CURRENT
LIMIT
28 CRES
REGULATOR
30 AUDIO8.3V
SERVO5V 31
MECH6V 33
32 GND
OVERVOLTAGE
PROTECTION
34 PANEL+B
VP 35
REFERENCE
VOLTAGE
B.UP+B 37
REGULATOR
BANDGAP
REFERENCE
36 CBU
LOADDUMP
PROTECTION
THERMAL
PROTECTION
BACK-UP
SWITCH
CDX-GT317EE/GT360
26
26
1
2
3
4
5
VIN
CONTROL
VOUT
VADJ
GND
CDX-GT317EE/GT360
IC401 BD3442FS-E2 (MAIN Board (2/3))
BUS-RCH 1
VCC2
32 F2L
100k
31 GND
BUS-LCH 2
INPUT
SELECTOR
100k
TU-RCH 3
INPUT
GAIN
VOLUME1
/MUTE
TREBLE
/BASS
/MIDDLE
VOLUME2
I2C
BUS
LOGIC
100k
TU-LCH 4
30 SDA
29 SCL
28 MUTE
100k
CD-RCH 5
VCC
27 VCC
100k
CD-LCH 6
FADER
26 OUT-FR
250k
FADER
25 OUT-FL
250k
FADER
24 OUT-RR
FADER
23 OUT-RL
100k
EFFECT
AUX-RCH 7
AUX-GND 8
AUX-LCH 9
250k
DS3-L 10
22 SUBOUT-R
DS1-L 11
FADER
DS2-L 12
LPF
21 SUBOUT-L
EBIAS 13
FADER
20 ADJ
DS2-R 14
19 SAOUT
SPECTRUM
ANALYZER
DS1-R 15
18 SADA
17 SACLK
DS3-R 16
IC50 TDA7333013TR (MAIN Board (2/3))
3
INTERPOLATOR
BAND PASS
FILTER
REF2 3
REF1 4
VSS 5
TM 6
VDDD 7
MPX
REF3 2
SINC4
FILTER
SIGMA DELTA
CONVERTER
SINC4REG
VDDA 1
RAM
RDS
RDSREG BUFFER
INTN DEMODULATOR &
&
SYNCHRONIZATION
CONTROL
LOGIC
16 MPX
15 INTN
SDAOUT
SDAIN
2
TEST LOGIC
SCK
I C/SPI
&
INTERFACE SPI
PIN MUX'S
TESTREG
14
13
12
11
CSN
SA_DATAOUT
SDA_DATAIN
SCL_CLK
2
10 XTO
OSCILLATOR
9 XTI
RESETN 8
27
CDX-GT317EE/GT360
• IC PIN DESCRIPTION
IC501 MB90F045PF-G-9015-SPE1 (SYSTEM CONTROL) (MAIN BOARD (3/3)) (CDX-GT360)
IC501 MB90F045PF-G-9043-SPE1 (SYSTEM CONTROL) (MAIN BOARD (3/3)) (CDX-GT317EE)
Pin No.
Pin Name
I/O
Pin Description
1
AREASEL0
I
Destination setting pin 0
2
AREASEL1
I
Destination setting pin 1
3
AREASEL2
I
Destination setting pin 2
4
B-OUT SEL
I
Black-out with/without discrimination signal input
5
BEEP
O
Beep signal output
6
NCO
O
Not used. (Open)
7
DIAG
I
Status signal input from power amplifier
8
AMPSTB
O
Standby signal output to power amplifier
9
VOLATT
O
Electronic volume attenuate control signal output
10
NCO
O
Not used. (Open)
11
VSS
—
Ground pin
12
TUATT
O
Tuner mute control signal output
13
NSMASK
O
Noise mask signal output
14
ILLUMI SEL
I
Illumination voltage setting signal input
“H”: Black-out
15
COL SEL
I
Two colors change setting signal input
16 to 22
NCO
O
Not used. (Open)
23
VCC5
—
Power supply pin (+3.3 V)
24
EEP SIO
I/O
EEPROM bus serial data signal input/output
25
EEP CKO
O
EEPROM bus serial clock signal output
26
RDS ON
O
RDS (Radio Data System) on signal output
27
FL CS
O
Fluorescent indicator tube chip select signal output
28
FL SO
O
Fluorescent indicator tube serial data signal output
29
FL SCK
O
Fluorescent indicator tube serial clock signal output
30
NCO
O
Not used. (Open)
31
RE IN0
I
Rotary encoder signal input 0
32
RE IN1
I
Rotary encoder signal input 1
33
I2C SCK
O
I2C bus serial clock signal output
34
I2C SIO
I/O
I2C bus serial data signal input/output
35
DAVDD
—
A/D converter power supply pin (+3.3 V)
36
AVRH
—
A/D converter external reference power supply pin (+3.3 V)
37
DAVSS
—
Ground pin
38
QUALITY
I
Noise detect signal input
39
VSM
I
S-meter voltage detect signal input
40
KEYIN1
I
Key signal input 1
41
KEYIN0
I
Key signal input 0
42
VSS
—
43
RCIN0
I
Rotary commander key signal input
44 to 47
NCO
O
Not used. (open)
48
AD ON
O
A/D converter power supply control signal output
49
MD0
I
Operation mode setting pin (Connect to VDD.)
50
MD1
I
Operation mode setting pin (Connect to VDD.)
51
MD2
I
Operation mode setting pin (Connect to VSS.)
52
KEYACK
I
Key acknowledgment detect signal input
53
TUATTIN
I
Tuner mute zero cross detect signal input
54
BUIN
I
Back-up power supply detect signal input
55
NCO
O
Not used. (Open)
28
Tuner on: “L”
Ground pin
Not used in this set.
CDX-GT317EE/GT360
Pin No.
Pin Name
I/O
56
DAVN
I
RDS (Radio Data System) data block synchronized detect signal input
Pin Description
57
NCO
O
Not used. (Open)
58
UNISI
I
SONY bus data signal input
59
UNISO
O
SONY bus data signal output
60
UNI SCK
O
SONY bus clock signal output
61
Z MUTE
I
Mute signal input
62
NOSE SW
I
Front panel attachment detect signal input
Memory mode change signal input
“L”: With panel, “H”: Without panel
Normally “H”: Single chip mode, after reset
63
FLASH W
I
64
SIRCS
I
Remote control signal input
65 to 70
NCO
O
Not used. (Open)
71
RC IN1
I
Rotary commander shift key signal input
72 to 76
NCO
O
Not used. (Open)
77
RESET
I
CPU reset signal input
78
NCO
O
Not used. (Open)
“L”: flash write mode
Not used in this set.
79
XIN
I
Low speed operation clock signal input (32.768 kHz)
80
XOUT
O
Low speed operation clock signal output (32.768 kHz)
81
VSS1
—
Ground pin
82
OSCIN
I
High speed operation clock signal input (18.432 MHz)
83
OSCOUT
O
High speed operation clock signal output (18.432 MHz)
84
VCC3
—
Power supply pin (+3.3 V)
85
CYRIL SEL
I
86
DEMOSEL
I
DEMO select signal input
87
FL ON
O
Fluorescent indicator tube power on signal output
88
SYSRST
O
System reset signal output
89, 90
NCO
O
Not used. (Open)
91
CDON
I
CD mechanism servo power supply control request signal input
Cyril correspondence discrimination signal input
“L”: No correspondence
“H”: DEMO on, “L”: DEMO off
92
CDMON
I
CD mechanism deck power supply control request signal input
93 to 95
NCO
O
Not used. (Open)
96
BUSON
O
Bus on signal output
97
TESTIN
I
Test mode detect signal input
98
TELATT
I
Telephone attenuate detect signal input
99
ACCIN
I
Accessory power supply detect signal input
100
ATT
O
Audio mute control signal output
29
CDX-GT317EE/GT360
SECTION 5
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
•
•
•
5-1.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
-XX and -X mean standardized parts, so
they may have some difference from the
original one.
Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
Accessories are given in the last of this parts list.
MAIN SECTION
not supplied
A
MG-101TA-188//Q
#2
7
#1
#3
B
A
#4
#5
F901
#4
4
#3
#6
#4
not supplied
5
not supplied
3
6
#1
TU1
not supplied
B
2
#1
not supplied
#1
1
Ref. No.
Part No.
Description
1
2
3
4
5
X-2148-784-1
3-042-244-11
X-2108-670-1
2-050-124-01
A-1206-400-A
PANEL (FL) ASSY, SUB
SCREW (T)
LOCK ASSY (S)
SCREW +BTT 2.6X5
MAIN BOARD, COMPLETE (GT317EE)
5
6
7
A-1206-410-A MAIN BOARD, COMPLETE (GT360)
2-021-848-01 SHEET (TU), GROUND
1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER)
(GT317EE)
1-833-100-11 CORD (WITH CONNECTOR) (POWER) (GT360)
7
30
Remark
Ref. No.
Part No.
Description
F901
TU1
TU1
#1
#2
1-532-877-11
A-3220-960-B
A-3220-961-B
7-685-792-09
7-685-790-01
FUSE (BLADE TYPE) (AUTO FUSE) 10A
TUNER UNIT (TUX-032) (GT360)
TUNER UNIT (TUX-032) (GT317EE)
SCREW +PTT 2.6X6 (S)
SCREW +PTT 2.6X4 (S)
#3
#4
#5
#6
7-685-793-09
7-685-794-09
7-685-134-19
7-621-284-40
SCREW +PTT 2.6X8 (S)
SCREW +PTT 2.6X10 (S)
SCREW +P 2.6X8 TYPE2 NON-SLIT
SCREW +P 2.6X10
Remark
CDX-GT317EE/GT360
5-2.
FRONT PANEL SECTION
57
56
RE901
not supplied
57
58
not supplied
(KEY board)
FL901
J901
55
not supplied
not supplied
52
54
not supplied
not supplied
53
51
Ref. No.
Part No.
Description
51
51
52
52
53
A-1206-402-A
A-1206-412-A
X-2149-356-1
X-2149-357-1
X-2149-360-1
PANEL COMPLETE ASSY, FRONT (GT317EE)
PANEL COMPLETE ASSY, FRONT (GT360)
BUTTON ASSY (S) (GT317EE)
BUTTON ASSY (S) (GT360)
PANEL (SV) ASSY, FRONT (GT317EE)
Remark
53
54
X-2149-361-1 PANEL (SV) ASSY, FRONT (GT360)
X-2149-353-1 KNOB (VOL) (SV) ASSY
Ref. No.
Part No.
Description
55
56
57
58
FL901
2-693-599-01
2-684-632-01
3-250-543-21
X-2149-228-2
1-519-909-12
SPRING (RELEASE)
PANEL (FL), BACK
SCREW (+B P-TITE M2)
CASE ASSY (for FRONT PANEL)
INDICATOR TUBE, FLUORESCENT
Remark
J901
RE901
1-820-624-11 JACK (SMALL TYPE) (VERTICAL) (AUX)
1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME)
31
CDX-GT317EE/GT360
Ver. 1.1
5-3.
CD MECHANISM SECTION
(MG-101TA-188//Q)
NOTE: Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP.
101
102
not supplied
not supplied
103
#7
#7
105
not supplied
not supplied
not supplied
not supplied
not supplied
104
not supplied
not supplied
not supplied
not supplied
107
106
106
Ref. No.
Part No.
Description
101
102
0 103
104
A-1177-168-A
A-1177-169-A
X-2149-672-1
2-626-869-01
MECHANICAL BLOCK ASSY
DAXEV//Q
SERVICE ASSY, OP (DAX-25A)
SCREW (M2X3), SERRATION
32
Remark
Ref. No.
105
106
107
#7
Part No.
Description
3-348-998-31
3-352-758-31
A-1177-201-A
7-627-000-08
SCREW (M1.4X2.5), TAPPING, PAN
SCREW (M1.7X2.5), TOOTHED LOCK
SERVO BOARD, COMPLETE
SCREW, PRECISION +P 1.7X2.2 TYPE3
Remark
CDX-GT317EE/GT360
SECTION 6
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
Ref. No.
Part No.
•
•
•
•
Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
CAPACITORS
uF : µF
COILS
uH : µH
Description
Remark
KEY BOARD
**********
< CAPACITOR >
C904
C974
C975
C976
C977
1-165-176-11
1-107-826-11
1-107-826-11
1-107-826-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.1uF
0.1uF
0.1uF
0.47uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
10V
C981
C982
C991
C992
1-107-826-11
1-107-826-11
1-216-295-11
1-216-295-11
CERAMIC CHIP
CERAMIC CHIP
SHORT CHIP
SHORT CHIP
0.1uF
0.1uF
0
0
10%
10%
16V
16V
< CONNECTOR >
CN901
1-820-619-11 PLUG, CONNECTOR 20P
< DIODE >
D882
D903
D904
D905
D906
8-719-057-80
8-719-057-80
8-719-057-80
8-719-977-12
8-719-977-12
DIODE
DIODE
DIODE
DIODE
DIODE
MA8180-M-TX
MA8180-M-TX
MA8180-M-TX
DTZ6.8B
DTZ6.8B
D907
D908
D971
8-719-977-12 DIODE DTZ6.8B
8-719-977-12 DIODE DTZ6.8B
8-719-420-90 DIODE MA8051-M
< FERRITE BEAD >
FB901
FB902
FB903
FB904
1-216-864-11
1-216-864-11
1-216-295-11
1-469-876-11
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
INDUCTOR, FERRITE BEAD
< FLUORESCENT INDICATOR TUBE >
FL901
1-519-909-12 INDICATOR TUBE, FLUORESCENT
< IC >
IC971
IC972
6-600-163-01 IC RS-770 (IR)
6-706-715-01 IC NJM2867F33(TE2)
< DIODE >
Ref. No.
KEY
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
Part No.
Description
LED843
LED844
LED845
LED846
LED847
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
LED
LED
LED
LED
LED
SML-310PTT86 (OFF) (GT317EE)
SML-310PTT86 (EQ3) (GT317EE)
SML-310PTT86 (PTY) (GT317EE)
SML-310PTT86 (SOURCE) (GT317EE)
SML-310PTT86 (MODE) (GT317EE)
Remark
LED850
LED851
LED852
LED853
LED854
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
LED
LED
LED
LED
LED
SML-310PTT86 (DSPL/DIM) (GT317EE)
SML-310PTT86 (1/ALBM –) (GT317EE)
SML-310PTT86 (2/ALBM +) (GT317EE)
SML-310PTT86 (3/REP) (GT317EE)
SML-310PTT86 (4/SHUF) (GT317EE)
LED855
LED856
LED857
LED861
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
LED
LED
LED
LED
SML-310PTT86 (5) (GT317EE)
SML-310PTT86 (6/PAUSE) (GT317EE)
SML-310PTT86 (AF/TA) (GT317EE)
SML-310PTT86 (RING ILLUMINATION)
(GT317EE)
LED862 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)
(GT317EE)
LED863 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)
(GT317EE)
LED864 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)
(GT317EE)
LED941 8-719-053-09 LED SML-310VTT86 (Z) (GT360)
LED942 8-719-053-09 LED SML-310VTT86 (CD INDICATOR)
(GT360)
LED943 8-719-053-09 LED SML-310VTT86 (OFF) (GT360)
LED944
LED945
LED946
LED947
LED950
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
LED
LED
LED
LED
LED
SML-310VTT86 (EQ3) (GT360)
SML-310VTT86 (PTY) (GT360)
SML-310VTT86 (SOURCE) (GT360)
SML-310VTT86 (MODE) (GT360)
SML-310VTT86 (DSPL/DIM) (GT360)
LED951
LED952
LED953
LED954
LED955
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
LED
LED
LED
LED
LED
SML-310VTT86 (1/ALBM –) (GT360)
SML-310VTT86 (2/ALBM +) (GT360)
SML-310VTT86 (3/REP) (GT360)
SML-310VTT86 (4/SHUF) (GT360)
SML-310VTT86 (5) (GT360)
LED956 8-719-053-09 LED SML-310VTT86 (6/PAUSE) (GT360)
LED957 8-719-053-09 LED SML-310VTT86 (AF/TA) (GT360)
LED961 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)
(GT360)
LED962 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)
(GT360)
LED963 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)
(GT360)
LED841 8-719-078-21 LED SML-310PTT86 (Z) (GT317EE)
LED842 8-719-078-21 LED SML-310PTT86 (CD INDICATOR)
(GT317EE)
33
CDX-GT317EE/GT360
KEY
Ref. No.
Part No.
Description
Remark
< SWITCH >
LSW901 1-786-805-12 SWITCH, TACTILE (WITH LED)
(M > SEEK +) (GT360)
LSW901 1-786-806-12 SWITCH, TACTILE (WITH LED)
(M > SEEK +) (GT317EE)
LSW902 1-786-805-12 SWITCH, TACTILE (WITH LED)
(. m SEEK –) (GT360)
LSW902 1-786-806-12 SWITCH, TACTILE (WITH LED)
(. m SEEK –) (GT317EE)
Ref. No.
Part No.
Description
R905
R906
R907
R908
R909
1-216-823-11
1-216-820-11
1-216-821-11
1-216-821-11
1-216-822-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
820
1K
1K
1.2K
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
R910
R911
R912
R913
R914
1-216-823-11
1-216-824-11
1-216-825-11
1-216-827-11
1-216-828-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
1.8K
2.2K
3.3K
3.9K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R915
R921
R922
R941
1-216-830-11
1-216-295-11
1-216-295-11
1-216-813-11
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
5.6K
0
0
220
5%
1/10W
5%
R942
1-216-813-11 METAL CHIP
220
5%
1/10W
(GT360)
1/10W
(GT360)
R943
1-216-812-11 METAL CHIP
180
5%
R944
1-216-811-11 METAL CHIP
150
5%
R945
1-216-812-11 METAL CHIP
180
5%
R946
1-216-811-11 METAL CHIP
150
5%
R947
1-216-811-11 METAL CHIP
150
5%
R947
1-216-812-11 METAL CHIP
180
5%
R948
1-216-810-11 METAL CHIP
120
5%
R948
1-216-811-11 METAL CHIP
150
5%
R949
1-216-809-11 METAL CHIP
100
5%
R950
1-216-809-11 METAL CHIP
100
5%
R951
1-216-809-11 METAL CHIP
100
5%
R952
1-216-809-11 METAL CHIP
100
5%
R953
1-216-812-11 METAL CHIP
180
5%
R954
1-216-811-11 METAL CHIP
150
5%
R961
1-216-809-11 METAL CHIP
100
5%
R962
1-216-809-11 METAL CHIP
100
5%
R971
R975
R976
R977
1-216-809-11
1-216-811-11
1-216-811-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
150
150
100
5%
5%
5%
5%
1/10W
(GT360)
1/10W
1/10W
1/10W
1/10W
R978
R981
R982
R983
R988
1-216-864-11
1-218-893-11
1-216-841-11
1-216-864-11
1-216-864-11
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
0
82K
47K
0
0
0.5%
5%
1/10W
1/10W
R989
1-216-845-11 METAL CHIP
5%
1/10W
< TRANSISTOR >
Q881
Q882
Q883
8-729-600-22 TRANSISTOR 2SA1235-F
8-729-600-22 TRANSISTOR 2SA1235-F
8-729-600-22 TRANSISTOR 2SA1235-F
< RESISTOR >
R841
1-216-810-11 METAL CHIP
120
5%
R842
1-216-810-11 METAL CHIP
120
5%
R843
1-216-811-11 METAL CHIP
150
5%
R844
1-216-810-11 METAL CHIP
120
5%
R845
1-216-811-11 METAL CHIP
150
5%
R846
1-216-810-11 METAL CHIP
120
5%
R849
1-216-807-11 METAL CHIP
68
5%
R850
1-216-807-11 METAL CHIP
68
5%
R851
1-216-807-11 METAL CHIP
68
5%
R852
1-216-807-11 METAL CHIP
68
5%
R853
1-216-811-11 METAL CHIP
150
5%
R854
1-216-810-11 METAL CHIP
120
5%
R861
1-216-811-11 METAL CHIP
150
5%
R862
1-216-810-11 METAL CHIP
120
5%
R863
1-216-811-11 METAL CHIP
150
5%
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
R864
1-216-810-11 METAL CHIP
120
5%
R881
R882
R883
R884
1-216-821-11
1-216-821-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
10K
5%
5%
5%
5%
1/10W
(GT317EE)
1/10W
1/10W
1/10W
1/10W
R885
R886
R887
R888
R889
1-216-833-11
1-216-833-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R901
R902
R903
R904
1-216-820-11
1-216-821-11
1-216-821-11
1-216-822-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
820
1K
1K
1.2K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
34
100K
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT317EE)
1/10W
(GT360)
1/10W
(GT317EE)
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT360)
CDX-GT317EE/GT360
KEY
Ref. No.
Part No.
Description
Remark
Part No.
Description
< SWITCH >
C151
C152
C153
C154
C155
1-126-960-11
1-126-960-11
1-126-961-11
1-163-017-00
1-163-017-00
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
2.2uF
0.0047uF
0.0047uF
20%
20%
20%
10%
10%
50V
50V
50V
50V
50V
< ROTARY ENCODER >
RE901
1-479-481-13 ENCODER, ROTARY (PUSH SELECT/VOLUME)
Ref. No.
MAIN
Remark
S901
S902
S903
S904
S906
1-786-653-21
1-786-653-21
1-786-653-21
1-786-653-21
1-786-653-21
SWITCH, TACTILE (Z)
SWITCH, TACTILE (OFF)
SWITCH, TACTILE (SOURCE)
SWITCH, TACTILE (EQ3)
SWITCH, TACTILE (PTY)
C200
C201
C202
C203
C204
1-107-826-11
1-124-234-00
1-107-826-11
1-126-965-11
1-107-826-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
22uF
0.1uF
22uF
0.1uF
10%
20%
10%
20%
10%
16V
16V
16V
50V
16V
S907
S908
S909
S910
S911
1-786-653-21
1-786-653-21
1-786-653-21
1-786-653-21
1-786-653-21
SWITCH, TACTILE (MODE)
SWITCH, TACTILE (DSPL/DIM)
SWITCH, TACTILE (1/ALBM –)
SWITCH, TACTILE (2/ALBM +)
SWITCH, TACTILE (3/REP)
C205
C206
C207
C301
C302
1-126-965-11
1-107-826-11
1-126-965-11
1-115-340-11
1-162-970-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
22uF
0.1uF
22uF
0.22uF
0.01uF
20%
10%
20%
10%
10%
50V
16V
50V
25V
25V
C303
C304
C305
C306
C307
1-128-551-11
1-115-340-11
1-162-970-11
1-124-261-00
1-162-970-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
22uF
0.22uF
0.01uF
10uF
0.01uF
20%
10%
10%
20%
10%
63V
25V
25V
50V
25V
C308
C309
C312
C313
C314
1-124-261-00
1-115-340-11
1-115-340-11
1-162-970-11
1-124-261-00
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
10uF
0.22uF
0.22uF
0.01uF
10uF
20%
10%
10%
10%
20%
50V
25V
25V
25V
50V
C315
C316
C317
C318
C319
1-162-970-11
1-124-261-00
1-124-257-00
1-162-923-11
1-127-715-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
2.2uF
47PF
0.22uF
10%
20%
20%
5%
10%
25V
50V
50V
50V
16V
C320
C325
C329
C330
C361
1-162-970-11
1-115-340-11
1-162-970-11
1-115-340-11
1-127-715-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.22uF
0.01uF
0.22uF
0.22uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
16V
C362
C363
C364
C365
C366
1-127-715-11
1-126-160-11
1-126-160-11
1-126-960-11
1-126-960-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.22uF
1uF
1uF
1uF
1uF
10%
20%
20%
20%
20%
16V
50V
50V
50V
50V
C401
C402
C403
C405
C409
1-124-234-00
1-162-970-11
1-124-584-00
1-124-234-00
1-124-261-00
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
22uF
0.01uF
100uF
22uF
10uF
20%
10%
20%
20%
20%
16V
25V
10V
16V
50V
C412
C413
C414
C415
C417
1-162-970-11
1-163-251-11
1-163-251-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
100PF
100PF
0.01uF
0.01uF
10%
5%
5%
10%
10%
25V
50V
50V
25V
25V
C418
C419
C421
C423
C424
1-162-966-11
1-162-966-11
1-126-964-11
1-165-908-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0022uF
10uF
1uF
100PF
10%
10%
20%
10%
5%
50V
50V
50V
10V
50V
C426
C431
C432
1-165-908-11 CERAMIC CHIP
1-124-261-00 ELECT
1-163-251-11 CERAMIC CHIP
1uF
10uF
100PF
10%
20%
5%
10V
50V
50V
S912
1-786-653-21 SWITCH, TACTILE (4/SHUF)
S913
1-786-653-21 SWITCH, TACTILE (5)
S914
1-786-653-21 SWITCH, TACTILE (6/PAUSE)
S915
1-786-653-21 SWITCH, TACTILE (AF/TA)
*************************************************************
A-1206-400-A MAIN BOARD, COMPLETE (GT317EE)
A-1206-410-A MAIN BOARD, COMPLETE (GT360)
*********************
7-621-284-40 SCREW +P 2.6X10
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-685-794-09 SCREW +PTT 2.6X10 (S)
< CAPACITOR >
C1
1-126-963-11 ELECT
4.7uF
20%
C2
C3
C5
C6
1-126-947-11
1-162-970-11
1-126-947-11
1-162-970-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
47uF
0.01uF
47uF
0.01uF
20%
10%
20%
10%
C7
C8
C15
1-162-970-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
0.01uF
0.01uF
0.1uF
10%
10%
10%
C50
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C51
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C52
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C53
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C54
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C55
1-107-826-11 CERAMIC CHIP
0.1uF
10%
C56
1-164-237-11 CERAMIC CHIP
16PF
5%
C57
1-164-237-11 CERAMIC CHIP
16PF
5%
C58
1-162-959-11 CERAMIC CHIP
330PF
5%
C60
1-162-970-11 CERAMIC CHIP
0.01uF
10%
C61
1-126-947-11 ELECT
47uF
20%
50V
(GT317EE)
35V
25V
35V
25V
25V
25V
16V
(GT360)
16V
(GT317EE)
16V
(GT317EE)
16V
(GT317EE)
16V
(GT317EE)
16V
(GT317EE)
16V
(GT317EE)
50V
(GT317EE)
50V
(GT317EE)
50V
(GT317EE)
25V
(GT317EE)
35V
(GT317EE)
35
CDX-GT317EE/GT360
MAIN
Ref. No.
Part No.
Description
Part No.
Description
C434
C441
C443
C444
C445
1-162-927-11
1-126-964-11
1-165-908-11
1-162-927-11
1-165-908-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
10uF
1uF
100PF
1uF
5%
20%
10%
5%
10%
Remark
50V
50V
10V
50V
10V
D109
D110
D111
D112
D113
8-719-977-12
8-719-977-12
8-719-977-12
8-719-977-12
8-719-977-12
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ6.8B
DTZ6.8B
DTZ6.8B
DTZ6.8B
DTZ6.8B
C451
C452
C454
C461
C462
1-126-964-11
1-163-251-11
1-162-927-11
1-126-964-11
1-165-908-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
100PF
100PF
10uF
1uF
20%
5%
5%
20%
10%
50V
50V
50V
50V
10V
D153
D200
D201
D202
D203
8-719-977-12
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ6.8B
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
C463
C471
C472
C473
C484
1-165-908-11
1-126-964-11
1-165-908-11
1-165-908-11
1-107-826-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
10uF
1uF
1uF
0.1uF
10%
20%
10%
10%
10%
10V
50V
10V
10V
16V
D204
D205
D206
D207
D301
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
DIODE
DIODE
DIODE
DIODE
DIODE
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
C485
C486
C491
C501
C502
1-126-933-11
1-126-964-11
1-124-589-11
1-162-970-11
1-162-964-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
100uF
10uF
47uF
0.01uF
0.001uF
20%
20%
20%
10%
10%
16V
50V
16V
25V
50V
D302
D303
D304
D305
D306
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
DIODE
DIODE
DIODE
DIODE
DIODE
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
C504
C507
C508
C509
C510
1-162-970-11
1-162-917-11
1-162-917-11
1-164-227-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
15PF
15PF
0.022uF
1uF
10%
5%
5%
10%
10%
25V
50V
50V
25V
10V
D307
D308
D309
D310
D311
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
DIODE
DIODE
DIODE
DIODE
DIODE
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
C512
C513
C514
C519
C600
1-162-964-11
1-162-970-11
1-162-964-11
1-107-826-11
1-126-935-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.001uF
0.01uF
0.001uF
0.1uF
470uF
10%
10%
10%
10%
20%
50V
25V
50V
16V
16V
D312
D353
D491
D491
D493
6-500-522-01
6-501-013-01
6-501-193-01
8-719-988-61
6-501-051-01
DIODE
DIODE
DIODE
DIODE
DIODE
10EDB40-TA1B2
BAT54ALT1G
1SS355WTE-17 (GT360)
1SS355TE-17 (GT317EE)
BAT54CLT1G
C601
C622
C623
C681
C682
1-162-970-11
1-126-924-11
1-126-916-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
330uF
1000uF
0.01uF
0.01uF
10%
20%
20%
10%
10%
25V
10V
6.3V
25V
25V
D502
D503
D503
D602
D603
8-719-060-48
6-501-193-01
8-719-988-61
8-719-057-80
8-719-422-64
DIODE
DIODE
DIODE
DIODE
DIODE
RB751V-40TE-17
1SS355WTE-17 (GT360)
1SS355TE-17 (GT317EE)
MA8180-M-TX
MA8062-M
C683
C701
C702
C703
C704
1-124-584-00
1-131-868-81
1-164-005-11
1-164-005-11
1-115-340-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
3300uF
0.47uF
0.47uF
0.22uF
20%
20%
10%
10V
16V
25V
25V
25V
D604
D605
D606
D607
D609
8-719-057-80
8-719-057-80
8-719-072-70
6-501-571-01
6-501-051-01
DIODE
DIODE
DIODE
DIODE
DIODE
MA8180-M-TX
MA8180-M-TX
MA2ZD14001S0
1N5404-C311-3
BAT54CLT1G
C705
C997
C998
1-115-340-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
0.22uF
0.001uF
0.001uF
10%
10%
10%
25V
50V
50V
D702
D703
D704
D901
D998
8-719-057-80
8-719-977-12
8-719-057-80
8-719-057-80
8-719-057-80
DIODE
DIODE
DIODE
DIODE
DIODE
MA8180-M-TX
DTZ6.8B
MA8180-M-TX (GT317EE)
MA8180-M-TX
MA8180-M-TX
PIN, CONNECTOR 16P
CONNECTOR, BOARD TO BOARD 28P
SOCKET, CONNECTOR 20P
PLUG, CONNECTOR 8P (BUS CONTROL IN)
D999
8-719-057-80 DIODE MA8180-M-TX
< CONNECTOR >
CN300
CN350
CN370
CNJ400
1-774-701-21
1-820-611-11
1-820-622-11
1-580-907-41
< DIODE >
D2
D101
D103
D104
D105
8-719-977-03
8-719-977-12
8-719-977-12
8-719-977-12
8-719-977-12
D106
D108
8-719-057-80 DIODE MA8180-M-TX
8-719-977-12 DIODE DTZ6.8B
36
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ5.6B
DTZ6.8B
DTZ6.8B
DTZ6.8B
DTZ6.8B
Ref. No.
Remark
< IC >
IC50
IC200
IC201
IC202
IC203
6-803-747-01
6-709-213-01
6-709-213-01
6-709-213-01
6-709-213-01
IC
IC
IC
IC
IC
TDA7333013TR (GT317EE)
NJM2387ADL3(TE2)
NJM2387ADL3(TE2)
NJM2387ADL3(TE2)
NJM2387ADL3(TE2)
IC300
IC401
IC501
IC501
IC601
6-705-359-02
6-710-065-01
6-710-298-01
6-807-262-01
6-703-884-01
IC
IC
IC
IC
IC
TDA8588AJ/N2/R1
BD3442FS-E2
MB90F045PF-G-9015-SPE1 (GT360)
MB90F045PF-G-9043-SPE1 (GT317EE)
BA8271F-E2
CDX-GT317EE/GT360
MAIN
Ref. No.
IC602
IC681
Part No.
Description
Remark
8-759-659-13 IC PST3428UL
6-705-373-01 IC MM3123DPLE
< JACK >
J1
J652
1-815-185-13 JACK (ANTENNA)
1-774-699-12 JACK, PIN 4P (BUS AUDIO IN,
AUDIO OUT REAR)
< JUMPER RESISTOR >
JC1
JC2
JC3
JC4
JC5
1-216-296-11
1-216-864-11
1-216-296-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC6
JC7
JC8
JC9
JC10
1-216-296-11
1-216-296-11
1-216-296-11
1-216-864-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC11
JC12
JC13
JC14
JC15
1-216-864-11
1-216-296-11
1-216-864-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC16
JC17
JC18
JC19
JC20
1-216-296-11
1-216-864-11
1-216-864-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC21
JC22
JC23
JC24
JC25
1-216-296-11
1-216-296-11
1-216-296-11
1-216-864-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC26
JC27
JC28
JC29
JC30
1-216-296-11
1-216-296-11
1-216-864-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC31
JC32
JC33
JC34
JC35
1-216-296-11
1-216-296-11
1-216-296-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC36
JC37
JC38
JC40
JC41
1-216-864-11
1-216-296-11
1-216-296-11
1-216-864-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0 (GT317EE)
0
0
JC42
1-216-296-11 SHORT CHIP
0
Ref. No.
Part No.
Description
L5
L50
L151
L300
L401
1-414-595-11
1-469-844-11
1-216-295-11
1-456-617-11
1-216-864-11
INDUCTOR, FERRITE BEAD (GT317EE)
INDUCTOR
2.2uH (GT317EE)
SHORT CHIP
0
COIL, CHOKE
SHORT CHIP
0
Remark
L402
L403
L405
L406
L407
1-216-295-11
1-216-295-11
1-216-864-11
1-500-245-11
1-216-864-11
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
INDUCTOR, FERRITE BEAD
SHORT CHIP
0
L409
L410
L501
L901
L902
1-469-844-11
1-469-876-11
1-469-844-11
1-216-295-11
1-469-844-11
INDUCTOR
2.2uH
INDUCTOR, FERRITE BEAD
INDUCTOR
2.2uH
SHORT CHIP
0
INDUCTOR
2.2uH
< TRANSISTOR >
Q1
Q3
Q50
Q420
Q432
8-729-027-43
6-551-431-01
8-729-600-22
8-729-027-44
6-550-752-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146 (GT317EE)
2SC6027T100-QR
2SA1235-F (GT317EE)
DTC114TKA-T146
DTC614TKT146
Q440
Q452
Q460
Q470
Q491
8-729-027-44
6-550-752-01
8-729-027-44
8-729-027-44
8-729-027-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114TKA-T146
DTC614TKT146
DTC114TKA-T146
DTC114TKA-T146
DTA114EKA-T146
Q492
Q600
Q601
Q605
Q664
8-729-027-43
8-729-047-76
8-729-027-23
8-729-027-43
8-729-027-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146
FMC2A-T148
DTA114EKA-T146
DTC114EKA-T146
DTA114EKA-T146
Q701
Q702
8-729-120-28 TRANSISTOR 2SC1623-L5L6 (GT317EE)
8-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
R1
1-216-809-11 METAL CHIP
100
5%
R2
R3
R4
R5
1-216-839-11
1-216-843-11
1-216-839-11
1-216-843-11
33K
68K
33K
68K
5%
5%
5%
5%
R6
R7
R8
1-414-595-11 INDUCTOR, FERRITE BEAD
1-414-595-11 INDUCTOR, FERRITE BEAD
1-216-839-11 METAL CHIP
33K
5%
R9
R10
1-216-843-11 METAL CHIP
1-216-821-11 METAL CHIP
68K
1K
5%
5%
R12
R13
R15
R52
1-216-811-11
1-216-811-11
1-216-864-11
1-216-845-11
150
5%
150
5%
0 (GT317EE)
100K
5%
R53
1-216-797-11 METAL CHIP
R54
R55
1-414-595-11 INDUCTOR, FERRITE BEAD (GT317EE)
1-216-797-11 METAL CHIP
10
5%
1/10W
(GT317EE)
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
< COIL >
L1
L2
L3
L4
L5
1-216-295-11
1-414-595-11
1-414-595-11
1-469-844-11
1-216-864-11
SHORT CHIP
0
INDUCTOR, FERRITE BEAD (GT317EE)
INDUCTOR, FERRITE BEAD (GT317EE)
INDUCTOR
2.2uH
SHORT CHIP
0 (GT360)
10
5%
1/10W
(GT317EE)
1/10W
1/10W
1/10W
1/10W
1/10W
(GT317EE)
1/10W
1/10W
1/10W
1/10W
1/10W
(GT317EE)
1/10W
(GT317EE)
37
CDX-GT317EE/GT360
MAIN
Ref. No.
Part No.
Description
Remark
R57
1-216-833-11 METAL CHIP
10K
5%
R58
1-216-821-11 METAL CHIP
1K
5%
R151
R152
R153
1-216-817-11 METAL CHIP
1-216-817-11 METAL CHIP
1-216-834-11 METAL CHIP
470
470
12K
5%
5%
5%
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
1/10W
1/10W
R154
R155
R200
R201
R202
1-216-834-11
1-216-825-11
1-216-833-11
1-216-822-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
12K
2.2K
10K
1.2K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R203
R204
R205
R206
R207
1-216-829-11
1-216-821-11
1-216-845-11
1-216-822-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
1K
100K
1.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R208
R209
R210
R211
R301
1-218-344-11
1-216-821-11
1-216-812-11
1-216-821-11
1-216-811-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
7.5K
1K
180
1K
150
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R302
R351
R355
R356
R357
1-216-841-11
1-216-845-11
1-216-833-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
100K
10K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R358
R401
R402
R420
R421
1-216-821-11
1-216-821-11
1-216-821-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
100
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R430
R431
R440
R442
R447
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R448
R449
R450
R451
R452
1-216-833-11
1-216-833-11
1-216-833-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R460
R461
R462
R470
R471
1-216-809-11
1-216-821-11
1-216-833-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
10K
100
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R472
R481
R485
R491
R502
1-216-833-11
1-216-801-11
1-218-883-11
1-216-805-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
22
33K
47
100
5%
5%
0.5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R503
R504
R505
R507
1-216-809-11
1-218-871-11
1-218-871-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
10K
100K
5%
0.5%
0.5%
5%
R509
1-216-809-11 METAL CHIP
100
5%
1/10W
1/10W
1/10W
1/10W
(GT360)
1/10W
38
Ref. No.
Part No.
Description
R510
R511
R512
R517
R519
1-216-864-11
1-216-809-11
1-216-809-11
1-216-841-11
1-216-845-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100
100
47K
100K
Remark
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R520
R521
R522
R523
R524
1-216-809-11
1-216-825-11
1-216-825-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
2.2K
2.2K
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R525
R526
R529
R531
R532
1-216-833-11
1-216-845-11
1-216-809-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
100
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R533
R534
R537
1-216-845-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-845-11 METAL CHIP
100K
10K
100K
5%
5%
5%
R538
1-216-845-11 METAL CHIP
100K
5%
R539
1-216-845-11 METAL CHIP
100K
5%
1/10W
1/10W
1/10W
(GT360)
1/10W
(GT317EE)
1/10W
(GT317EE)
R540
1-216-845-11 METAL CHIP
100K
5%
R544
R549
1-216-809-11 METAL CHIP
1-216-845-11 METAL CHIP
100
100K
5%
5%
R550
1-216-845-11 METAL CHIP
100K
5%
R551
1-216-845-11 METAL CHIP
100K
5%
R552
1-216-845-11 METAL CHIP
100K
5%
R553
R555
R556
R557
1-216-845-11
1-216-845-11
1-216-845-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100
5%
5%
5%
5%
R558
R560
R561
R563
R564
1-216-833-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
(GT317EE)
R565
R566
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
100K
100K
5%
5%
R567
R568
R570
1-216-845-11 METAL CHIP
1-216-849-11 METAL CHIP
1-216-809-11 METAL CHIP
100K
220K
100
5%
5%
5%
1/10W
1/10W
(GT360)
1/10W
1/10W
1/10W
R573
1-216-845-11 METAL CHIP
100K
5%
R600
R601
R602
R603
1-216-845-11
1-216-851-11
1-216-851-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
330K
330K
1K
5%
5%
5%
5%
1/10W
(GT317EE)
1/10W
1/10W
1/10W
1/10W
R604
R606
R607
R608
1-216-835-11
1-216-821-11
1-216-821-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
1K
1K
4.7K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
(GT360)
1/10W
1/10W
(GT317EE)
1/10W
(GT360)
1/10W
(GT360)
1/10W
(GT317EE)
1/10W
1/10W
1/10W
1/10W
CDX-GT317EE/GT360
MAIN
Ref. No.
Part No.
Description
R610
R611
R612
R615
R616
1-216-809-11
1-216-864-11
1-216-864-11
1-216-809-11
1-216-864-11
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
100
0
0
100
0
5%
1/10W
5%
1/10W
R636
R671
R672
R673
R674
1-216-845-11
1-216-809-11
1-216-809-11
1-216-833-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100
100
10K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R701
1-216-821-11 METAL CHIP
1K
5%
R702
1-216-841-11 METAL CHIP
47K
5%
R703
1-216-833-11 METAL CHIP
10K
5%
R704
1-216-833-11 METAL CHIP
10K
5%
R705
1-249-425-11 CARBON
4.7K
5%
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/10W
(GT317EE)
1/4W
R706
R707
R708
R709
1-216-841-11
1-216-841-11
1-216-829-11
1-216-833-11
47K
47K
4.7K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
Remark
Ref. No.
Remark
1-479-077-13 REMOTE COMMANDER (RM-X151)
2-548-729-01 LID, BATTERY CASE (for RM-X151)
2-886-504-21 MANUAL, INSTRUCTION (ENGLISH,RUSSIAN)
(GT317EE)
2-886-504-41 MANUAL, INSTRUCTION (ENGLISH) (GT360)
2-886-505-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
RUSSIAN) (GT317EE)
2-886-505-41 MANUAL, INSTRUCTION, INSTALL (ENGLISH)
(GT360)
X-2149-228-2 CASE ASSY (for FRONT PANEL)
*************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS
***************************************
151
152
153
154
155
X-3382-647-1
2-686-803-01
3-246-471-01
X-3381-154-1
3-349-410-11
156
157
1-465-459-31 ADAPTOR, ANTENNA (GT317EE)
1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER)
(GT317EE)
1-833-100-11 CORD (WITH CONNECTOR) (POWER) (GT360)
158
FRAME ASSY, FITTING
COLLAR
KEY (FRAME)
SCREW ASSY (BS4), FITTING
BUSHING
1-786-826-11 SWITCH, TACTILE (RESET)
< THERMISTOR (POSITIVE) >
TH400
Description
ACCESSORIES
************
< SWITCH >
S103
Part No.
151
152
153
1-803-350-21 THERMISTOR, POSITIVE
< TUNER UNIT >
TU1
TU1
SERVO
A-3220-960-B TUNER UNIT (TUX-032) (GT360)
A-3220-961-B TUNER UNIT (TUX-032) (GT317EE)
×2
154
155
< VIBRATOR >
X50
1-813-173-11 VIBRATOR, CRYSTAL (8.664MHz) (GT317EE)
X501
1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)
X502
1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
*************************************************************
×4
156
157
158
A-1177-201-A SERVO BOARD, COMPLETE
**********************
*************************************************************
MISCELLANEOUS
***************
7
1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER)
(GT317EE)
7
1-833-100-11 CORD (WITH CONNECTOR) (POWER) (GT360)
0 103
X-2149-672-1 SERVICE ASSY, OP (DAX-25A)
F901
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
J901
1-820-624-11 JACK (SMALL TYPE) (VERTICAL) (AUX)
*************************************************************
39
CDX-GT317EE/GT360
MEMO
40
CDX-GT317EE/GT360
Saudi Arabia Model
CDX-GT360
East European Model
SERVICE MANUAL
CDX-GT317EE
Ver. 1.1 2007.03
SUPPLEMENT-1
File this supplement with the service manual.
Subject: Notes for removal of the OPTICAL PICK-UP added.
DISASSEMBLY
1. CHUCKING ARM SUB ASSY
3 chucking arm sub assy
1 spring
2
Note: Have this portion receive the chassis.
Note: Have this portion receive the chassis.
Note: Be careful not to touch the turn table.
9-887-460-81
CDX-GT317EE/GT360
2. SLED MOTOR ASSY
2 three serration screws
(M 2 × 3)
3 sled mtor assy
1 spring
turn table
spring
stand
Note:
Never remove these parts since they were adjusted.
stand
Note: Place the stand with care not to touch the turn table.
Note for Assembly
three serration screws
(M 2 × 3)
sled mtor assy
Note: Take care to prevent the chassis from being bent
when tightening the three machine screws.
2
CDX-GT317EE/GT360
3. OPTICAL PICK-UP SECTION
2 optical pick-up section
1
Note: Be careful not to touch the lens and hologram
terminal when removing the optical pick-up section.
4. OPTICAL PICK-UP
1 pan tapping screw
(M 1.4 × 2.5)
2 leaf spring (sub guide)
3 leaf spring (OP)
5 optical pick-up
4 lead screw assy
Notes for Assembly
Prevent the end of the
leaf spring (sub guide) from being
in contact with the OP slide base.
Prevent the end of the
leaf spring (sub guide) from being
in contact with the OP slide base.
There is space at the end of the
leaf spring (sub guide) to avoid
contact with the slide.
3
CDX-GT317EE/GT360
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.
Date
Description of Revision
1.0
2006.10
New
1.1
2007.03
Notes for removal of the OPTICAL PICK-UP added.
(SUPPLEMENT-1)
4
(ENG-07003)
www.s-manuals.com