Download RSH-1650 & 1050 Service Manual - 05.07.08

ROLL LAMINATOR
Service Manual
www.royalsovereign.com
Table of Contents
1.Safety Precautions
………………………………………………………………………
3 ~ 3
……………………………………………………………………………
4 ~ 13
2.1) Rollers Not Heating ………………………………………………………………………………
4 ~ 5
2.2) Rollers Over Heating ……………………………………………………………………………
6 ~ 6
2.3) Rollers Not Running ………………………………………………………………………………
7 ~ 9
2.4) No Main Power ……………………………………………………………………………………
9 ~ 10
2.5) Count Sensor Not Working ………………………………………………………………………
11 ~ 13
2.Troubleshooting
3.Replacing Parts
………………………………………………………………………………
14 ~ 16
3.1) Right Cover …………………………………………………………………………………………
14 ~ 14
3.2) Left Cover
…………………………………………………………………………………………
15 ~ 15
3.3) Rear Cover …………………………………………………………………………………………
15 ~ 15
3.4) Main PCB ……………………………………………………………………………………………
15 ~ 15
3.5) Sub PCB ………………………………………………………………………………………………
15 ~ 15
3.6) Heaters ………………………………………………………………………………………………
16 ~ 16
3.7) Cross Cutter …………………………………………………………………………………………
16 ~ 16
4.Adjustments
……………………………………………………………………………………
17 ~ 17
4.1) Adjusting Take-Up Shaft Speed
………………………………………………………………
17 ~ 17
4.2) Adjusting Front and Rear Roller
………………………………………………………………
17 ~ 17
5. Optioning Equipment
6. Parts List
…………………………………………………………………… 18 ~ 18
…………………………………………………………………………………………
19 ~ 28
6.1) RSH-1650 Parts List ………………………………………………………………………………
19 ~ 23
6.2) RSH-1050 Parts List ………………………………………………………………………………… 24 ~ 28
7.Exploded Drawings
………………………………………………………………………
29 ~ 43
7.1) RSH-1650 Whole Exploding Drawing and Part Exploding Drawing ……………………
30 ~ 36
7.2) RSH-1050 Whole Exploding Drawing and Part Exploding Drawing ……………………
37 ~ 43
8.Wire Diagram
…………………………………………………………………………………… 44 ~ 47
2
1. Safety Precautions
Failure to comply any of the following safety procedures could result in
serious injury. Please read the instructions carefully and keep for future
reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct
voltage.
3. Keep hands and clothing (ie.Neckties)away from rollers. The rollers are pinch
points that can trap body parts or clothing and cause serious injury .
Safety Precaution
4. Keep flammable and wet objects away from the machine .
5. Place machine on a sturdy and level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled ,and unplugged from the outlet prior to
moving and/or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should
make repairs.
10. Do not attempt to laminate items that exceed total recommended material
thickness for the unit.
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they are hot or place foreign objects inside the
machine.
13. Do not cover the surface of the machine until the machine has completely
cooled.
18 ~ 22
3
2. Troubleshooting
Note: While repairing:
a.
Make sure the power plug is unplugged from the power outlet.
b.
Open both side covers and rear cover.
c.
Be sure to follow the steps below in order.
2.1 Rollers Not Heating
CAUSES:
1. Improper laminating mode.
2. Heating wire is not connected to the main PCB.
3. Blown (burnt) upper and/or lower wire fuse (T/Fuse).
4. Defective Bi-Metal.
5. Defective heater.
6. Defective Main PCB.
MEASURE
1. Improper laminating mode.
a. Ensure that the laminating mode is in the “Hot” mode, not the “Cold” mode.
Press “C/HOT” button on the control panel to change the mode.
2. Heating wire is not connected to the main PCB.
a. Connect the upper and lower heating wires to the main PCB.
18 ~ 22
4
3. Blown (burnt) upper and/or lower wire fuse (T/Fuse).
a. Replace the T/Fuse wire located on the left-hand side.
WIRET/FUSE
4. Defective Bi-Metal.
a. Replace the Bi-Metal
BI- METAL
5. Defective heater.
a. Using the multi-meter, test the continuity of the heater. If it fails, replace the heater.
Multi-meter
b. Physically examine the heater assembly for breakage.
13. Remote Control and Foot Pedal wires.
Broken
6. Defective Main PCB.
a. Replace the PCB Main.
5
2.2) Rollers Over Heating
CAUSES
1. Lower and upper heat sensors are reversed on the PCB Main.
2. Defective T/Fuse wire.
3. Defective heater.
4. Defective main PCB.
MEASURES
1. Wires for lower and upper heat sensors are reversed on the main PCB.
a. Reverse the heat sensors.
Connector-Wire
Sensor
2. Defective T/Fuse wire.
a. Replace the T/Fuse wire located on the left-hand side.
WIRE-T/FUSE
3. Defective heater.
a. Test continuity of the heater. If it fails, replace the heater.
b. Glass tube that surrounds heating coil is broken – replace the heating element.
4. Defective Main PCB.
a. Replace the PCB Main.
6
2.3) Rollers Not Running
CAUSES
1. No power to the unit.
2. Emergency switch is engaged.
3. Disengaged Paper Guide switch.
4. Opened safety cover.
5. Film is jammed on the rollers.
6. Disconnected motor wire.
7. Blown motor fuse.
8. Defective main motor.
9. Defective main PCB.
MEASURES
1. No power to the unit.
a. Make sure the power plug is connected to the proper source of outlet
(220V, 15Amp, & single phase).
2. Emergency switch is engaged.
a. Disengage the emergency switches located on the front and on the rear of the machine
by rotating the knob clock-wise.
Front Left
Rear Left
3. Disengaged Paper Guide switch.
a. Properly position the paper guide to engage the switch.
Paper Guide
7
4. Opened safety cover.
a. Close the safety cover and double check to insure that the safety cover switch
is engaged.
Note: By closing the safety cover, it engages the safety cover switch.
Safety Cover Switch
Switch is engaged
5. Film is jammed on the rollers.
a. Un-jam the film using a combination of the pressure lever and reverse button.
6. Disconnected motor wire.
a. Check the motor wire connection in both locations.
Motor wire connector
from the PCB
Motor wire connector
from the Motor
8
7. Blown motor fuse.
a. Replace the motor fuse located above the main power switch.
Motor Fuse
8. Defective main motor.
a. Replace the main motor.
8. Defective main motor.
a. Replace the main motor.
9. Defective main PCB.
a. Replace the main PCB.
2.4) No Main Power
CAUSES
1. No electricity.
2. Blown main fuse.
3. Disconnected main power wires.
4. Defective transformer.
MEASURES
1. No Electricity.
a. Double check to insure that you have electricity from your outlet.
b. Check the circuit breaker.
c. Double check that source of power is 220V, 15Amp, and single phase.
9
2. Blown main fuse.
a. Replace the main fuse located above the main power switch.
Main Fuse
3. Disconnected main power wires.
a. Check that the main power wires are properly connected.
Main Power Wires
4. Transformer is defective
a. Replace the transformer.
Transformer
10
2.5) Count Sensor Not Working.
CAUSES
1. The option fiber cable is not connected with optical fiber AMP.
2. The upper sensor is aligned properly with lower sensor.
3. The counter wires are not connected on the Main PCB.
4. Main PCB is defective.
5. The count needs adjustment.
MEASURES
1. The option fiber cable is not connected with optical fiber AMP.
Optical Fiber Cable
Optical Fiber AMP
2. The upper sensor is aligned properly with lower sensor.
Upper Sensor
Lower Sensor
11
3. The counter wires are not connected on the Main PCB.
a. Ensure that the counter wires are connected to the Main PCB.
Counter Wires
4. Main PCB is defective.
a. Replace the Main PCB.
5. The count needs adjustment.
a. Please see below for adjustments.
12
Adjusting the Counter Sensor
VR
NO.
1
Throught beam
Initial setting
Received light
2
Adjusting
Fix VR(Coarse) at ON
position with turning right
slowly when it is the status
of the recviced light.
Fix VR(Coarse) at ON position
with turning right slowly when it
is the status of the recviced
light.
Fine
Coarse
Min.
(-)
(+)
ON
Min.
(-)
(+)
ON
Received light
3
Interrupted light
4
And then turning VR(Fine) until it
is ON toward(+),and turning until
it is OFF toward(-) again in state
of shading light.Then confirm
that this position will be B
position.(when it will not be
ON.max. position will be B.
A
OFF
(-)
Coarse VR is
not required to
adjust
afterwards.
Received light
If it cannot adjust as above
method. set VR(Fine) at
max. position toward(+),then
execute again.
13
(+)
OFF
(-)
Fix it at middle of A and B
position.
This will be the best position
to set.
5
6
Turning VR(Fine) until it is
OFF toward(-),and turning until
it is ON toward(+) again ,then
confirm that this will be A
position.
B
(+)
ON
A
(-)
Min.
(-)
B
(+)
(+)
Max.
3. Replacing Parts
Note: While replacing parts:
a. Make sure the power plug is unplugged from the power outlet.
b. Open both side covers and rear cover.
3.1 Replacing the Right Cover.
a. Take out the pressure lever (Figure 1) and four cover screws using Phillips screw driver (Figure 2).
Figure 1
Figure 2
b. Pull out the male control panel connector from the Sub-PCB. Figure 3
Figure 3
c. Loosen two screws from Sub-PCB and install on to new Right Cover. Figure 4
18 ~ 22
Figure 4
d. Follow the reverse order to assemble the Right Cover back.
14
3.2 Replacing the Left Cover
a. Replace the Left Cover by loosening four Left Cover screws.
3.3 Replacing Rear Cover
a. Take off the left and right covers.
b. Take out the seven screws from the back cover. Figure 5
c. Carefully slightly lift up the cover and slowly pull towards you. Figure 6
(Note: The Counter Sensor Wire is attached to the cover).
d. Open the Paper Counter latch and pull the black wire from the paper counter sensor to
detach from the unit.
Paper Counter Latch
Figure 5
Upper black wire
Figure 6
3.4 Replacing the Main PCB
a. Remove the rear cover and label all the wires before unplugging from the Main PCB.
b. Detach the Main PCB from 6 white plastic holders. Figure 7
c. Replace the board with new PCB and connect all the wires.
Figure 7
3.5 Replacing the Sub-PCB
a. Refer to “Replacing Right Cover”.
15
3.6 Replacing the Heaters
Note: Cotton or surgical gloves are recommended while handling the heater assembly.
a. Disassemble Right and Left Covers (Refer to “Replacing Right Cover” and “Replacing Left Cover”).
b. Take out the heater brackets on each side by loosening the nuts and screws (Figure 8, 9, & 10).
Figure 8
Figure 9
Figure 10
c. Take out the broken heater. Figure 11
Figure 11
Note:
a. When inserting the heater into the roller, rotate the heater slightly and push the rod in gently.
b. Use an air blower to blow out the broken pieces of heating rod.
(Please ensure that no one is standing on the other side.)
3.7 Replacing the Cross Cutter
a. Disassemble the nut from the Frame-Cutter.
b. Unfasten the spring from the cutter.
c. Change the Cutter.
d. Assemble the Cutter by reversing the above steps.
16
4. Adjustments
4.1 Adjusting Take-up Shaft Speed
CAUSES:
1.Main rollers and take-up shaft speed is not synchronized.
MEASURES:
1. Take off the take up motor cover. Figure 1
2. Loosen (increases speed) or tighten (reduces speed) the bolt using 11/16” or 17mm wrench.
Note: Loosen three screws as shown in Figure 1 to get to the adjustable take-up shaft speed bolt.
Figure 2
Increase
Decrease
Figure 2
Figure 1
4.2 Adjusting Front and Rear Rollers
C.W
Pressure
• Use 5/16” or 8mm Allen wrench
to adjust the roller pressure:
C.W – Increase pressure.
C.C.W – Decrease pressure.
1.Using Push-Pull Scale , measure
5 spots as shown on Figure B &C:
Front roller should be 2~3 on Guage
C.C.
Figure A
when the machine is running, check that
the top and the bottom films are fed in
without any wrinkles.
Figure B
3.Laminating Test – Laminate samples
with different thickness of substrates.
4.Check above steps 2 through 3 with
1.5mil & 5mil films.
Figure C
17
5. Installing Options
Note:
Only on RSH-1650 model and these options are to be installed by an authorized RS reseller.
1. Installing the Front Feeder
a. Install the Left and Right Front Feed option on the inside of
the front frames using four 9/16” hexagon bolts on each side.
Figure 1
Figure 1
2. Installing the Rear Rewinder
a. Remove the left and right covers by using a Phillips screwdriver
(four screws on each side cover) (Figures 2 & 3).
Figure 2
Figure 3
b. Remove the lever knob screw and lever (Figure 4).
Figure 4
c. Remove the rear cover by removing all
10 screws (4 top, 4 bottom, and 1 on each side)
(Figure 5 & 6).
18 ~ 22
Figure 5
Figure 6
d. Disassemble the power switch bracket and place the left rewinder
outside of the frame; fasten with round head 5/16 (9mm) Phillips
screws (included in the option kit). Then, reinstall the power
switch bracket (Figure 7).
Figure 7
e. Install the right rewind on the outside of
the frame and connect the motor wire
connection to rear wire (Figures 8 & 9).
f. Reinstall the rear cover.
g. Reinstall the side covers.
h. Reinstall the lever knob and screw.
Figure 8
18
Figure 9
6. Parts List
6.1 RSH-1650 Parts List
RSH-1650
NO
Part N/O
Part Name
Q'TY
1
13500X001A
CASTER-STAND1
2
2
13500X002A
CASTER-STAND2
2
3
WSB16038D0
WASHER-SPRING
4
4
212LR1003A
STAND-FRAME
2
5
212LR1005C
STAND-CENTER
1
6
BHE08015D2
BOLT
20
7
WSB08020D2
WASHER-SPRING
28
8
NHB08065D2
NUT
8
9
BHE08100D2
BOLT
8
10
212LR2003A
STAND TOP
1
11
013LR3006A
FRAME-BASE
1
12
BHE06020D2
BOLT
14
13
WSB06015D2
WASHER-SPRING
10
14
MBC05030D2
SCREW BH
10
15
211003002B
BLOWER-ASS'Y
3
16
MBC04008D2
SCREW BH
45
17
WSB04010D2
WASHER-SPRING
52
18
141LR3001B
BRACKET-PCB
1
19
23200X001A
SUPPORT-B/K PCB
10
20
350LR3006A
PCB-MAIN ASS'Y
1
21
MBC04010D2
SCREW-BH
12
22
34000S008A
POWER TRANSFORMER
1
23
013LR2010A
FRAME-L
1
24
013LR2011A
FRAME-R
1
25
013LR2009B
FRAME-FRONT
1
26
214LR3003A
MASH-FRAME,F
3
27
138LR4009A
SPRING-HEATER SUPPORT
6
28
133LR2007A
ROLLER-LAMI, LO
1
29
141LR4036A
BRACKET-SENSOR
1
138LR4008A
SPRING-PRESSURE
4
31
013LR3005A
FRAME-CENTER
1
32
NHB05038D2
NUT
12
33
21000S019A
MOTOR-MAIN
1
34
013LR2013A
FRAME-GUIDE,PAPER
1
35
142LR4002A
SPACER-GUIDE
2
36
133LR2007B
ROLLER-LAMI, UP
1
37
122LR4008A
BUSH-ROLLER,LAMI LO
2
38
12200X012A
DU-BUSH
4
39
133LR2009A
ROLLER-PULL,LO
1
40
141LR2011A
PLATE-PRESSURE,L
1
41
141LR2012A
PLATE-PRESSURE,R
1
42
120LR3002A
SHAFT-CAM
1
43
122CR4002A
BEARING-CAM
2
19
RSH-1650
NO
Part N/O
Part Name
Q'TY
44
RC000800C8
SNAP RING
2
45
124LR4002A
CAM-ROLLE Cu+Ni+Cr
2
46
SKE05015D2
M5*15 FZB
4
47
122LR4004A
BUSH-PLATE PRESSURE
6
48
RC001500C8
SNAP RING
8
49
133LR2008A
ROLLER-PULL,UP
1
50
122LR4007B
BUSH-ROLLER,LAMI UP
2
51
122LR4009A
BUSH-ROLLER,PULL UP
2
52
111LR4014A
BOLT-PRESSURE
4
53
WPB06016A6
WASHER-PLAIN
4
54
NHB04032D2
NUT
2
55
120LR4001B
SHAFT-TABLE
1
56
015LR3005A
BAR-IDLE,UP
1
57
12200X016A
BEARING-IDLE
2
58
141LR4012A
PLATE-BEARING
2
59
015LR3005B
BAR-IDLE,LO
1
60
12200X020A
BEARING-IDLE,LO
2
61
12200X014A
DU BUSH
2
62
013LR2012B
FRAME-SENSOR
1
63
223LR2003A
HEATER-ASS'Y
2
64
122LR4010A
BUSH-ROLLER,PULL LO
2
65
12200X013A
DU BUSH
4
66
12200X015A
DU BUSH
2
67
313LR3001A
SENSOR-ASS'Y
2
68
140LR4002A
HOLDER-SHAFT,T
1
69
381LR4032A
WIRE-REMOTE
1
70
12200X022A
BEARING-RADIAL TRUST
5
71
381LR4046A
WIRE-COUNT
1
72
381LR4045A
WIRE-LENGTH
1
73
013LR3002B
FRAME-CUTTER
1
74
023LR3003A
KNOB-CUTTER,C
1
75
140LR3001A
HOLDER-CUTTER,C
1
76
213LR4001A
CUTTER-CROSS
1
77
138LR4001A
SPRING-CROSS,CUTTER
1
78
NHB03024D2
NUT-BRACKET SWITCH
5
79
MPC03006D2
SCREW PH
6
80
12200X002A
DU BUSH
2
81
RC001000C8
SNAP RING
2
82
32500X0005
FUSE-MAIN
2
83
36600X002A
FUSE BLOCK
1
84
021LR3003A
CASE-SENSOR,UP
2
85
021LR3004A
CASE-SENSOR,LO
2
86
381LR4035A
WIRE-MOTOR
1
87
381LR4027E
WIRE-SENSOR
1
88
381LR4048A
WIRE-TAKE UP2
1
89
111LR4004A
BOLT-CORE
8
90
141LR4016A
BRACKET-HEATER
2
91
120LR3004B
SHAFT-FILM,LO
2
20
RSH-1650
NO
Part N/O
Part Name
Q'TY
92
143LR3001A
SUPPORTER-SHAFT,LO
2
93
141LR4005A
PLATE-SHAFT,FILM
3
94
140LR4001A
HOLDER-SHAFT,FILM
2
95
147LR4002A
PAD-TENSION
2
96
141LR4011A
BRACKET-HEATER,STOPPER
4
97
12200X009A
DU BUSH
2
98
WSB03007D2
WASHER-SPRING
8
99
138LR4002A
SPRING-FILM,TENSION
2
100
125LR4001A
HANDLE-TENSION
2
101
124LR3001A
CORE-57
6
102
142LR4001A
SPACER-HEATER,BKT
4
103
MBC04040D2
SCREW BH
4
104
141LR4009A
BRACKET-REAR COVER
4
105
MBC05010D2
SCREW BH
8
106
WSB05013D2
WASHER-SPRING
30
107
023LR4002A
KNOB-BOLT,GUIDE
2
108
111LR4006A
BOLT-GUIDE
2
109
120LR4002B
SHAFT-TAKE UP
1
110
113LR4001A
WASHER TAKE UP
4
111
130LR4005A
GEAR-TAKE UP
1
112
141LR4006A
PLATE-SLIP
1
113
138LR4006A
SPRING-SLIP
2
114
WPB08016A6
WASHER-PLAIN
3
115
141LR4003A
BRACKET-MOTOR
1
116
130LR4004A
GEAR-MOTOR
2
117
RE000400D2
E-RING
1
118
21000S027A
MOTOR-AC
1
119
021LR2003A
COVER-TAKE UP,L
1
120
021LR2004A
COVER-TAKE UP,R
1
121
36400X003A
SWITCH-POWER
1
122
MBC04006D2
SCREW BH
37
123
112004001C
NUT
1
124
014LR1003B
TABLE-FRONT
1
125
145LR3001A
GUIDE-DOCUMENT
2
126
SKE04010D2
SCREW-SET
3
127
SKE04015D2
SCREW-SET
2
128
122LR4006A
BUSH-PULLEY
1
129
134LR4002A
PULLEY-CHAIN
1
130
BHE08045D2
BOLT
1
131
141LR4007A
BRACKET-SWITCH,EU
1
132
36400X002A
SWITCH-MAIN
1
133
36400X001A
SWITCH-EMERGENCY
2
134
23300X001A
BUSHING-CORD,EU
1
135
380LR4001A
POWER CORD-EU
1
136
SKE05015D2
SCREW-SET
4
137
SKE06010D2
SCREW-SET
1
138
SKE06015D2
SCREW-SET
1
139
SKE05010D2
SCREW-SET
2
21
RSH-1650
NO
Part N/O
Part Name
Q'TY
140
021LR2001A
COVER-L
1
141
032LR4008A
SHEET-CUTTER
1
142
381LR4043A
WIRE-SAFETY SWITCH
1
143
131LR4004A
SPROCKET-MOTOR
1
144
131LR4016A
SPROCKET-ROLLER,LAMI
1
145
WPB04008D2
WASHER-PLAIN
5
146
147LR4001A
PAD-SLIP
2
147
131LR4015A
SPROCKET-ROLLER,PULL
1
148
WPB13025A6
WASHER-PLAIN
3
149
MBC04018D2
SCREW BH
7
150
112004001B
NUT
1
151
136LR4004B
CHAIN-ROLLER
1
152
136LR4004A
CHAIN-ROLLER
1
153
011LR2003A
COVER-REAR
1
154
021LR2002A
COVER-R
1
155
032LR3004A
SHEET-FUNC
1
156
032LR4010A
SHEET-PRESSURE-EU,AU
1
157
023LR3006A
BUTTON-FUNC
1
158
350LR3007A
PCB-SUB ASS'Y
1
159
144LR4001A
CLAMPER-LEVER
1
160
125LR4003A
LEVER-PRESSURE
1
161
023LR4001A
KNOB-LEVER
1
162
MFC04008D2
SCREW FH
6
163
365LR4003A
SWITCH-FOOT ASS'Y
1
164
025LR4001A
CASE-REMOCON ASS'Y
1
165
350CR4001A
PCB-REMOCON ASS'Y
1
166
23300X008A
CABLE GRAND
2
167
381LR4055A
WIRE-UP HEATER 2,EU
1
168
138LR4014A
SPRING-HEATER
4
169
381LR4020B
WIRE-FUSE,EU
1
170
381LR4029A
WIRE-LO HEATER,EU
2
171
381LR4030A
WIRE-UP HEATER,EU
2
172
381LR4013B
WIRE-POWER S/W,EU
1
173
381LR4054A
WIRE-LO HEATER 2,EU
1
174
381LR4047A
WIRE-EMER
1
175
381LR4044A
WIRE-MAIN
1
176
1PC03006D2
SCREW TAP TATE PH
2
177
24000X003A
TAPE-TEFLON
1
178
MPC03014D2
SCREW PH
4
179
12200X025A
BEARING-SLIP
2
180
141LR4015A
BRACKET-MICRO SWITCH
1
181
36400X014A
SWITCH MICRO-SAFETY COVER
2
182
MBC05018D2
SCREW BH
4
183
MFC05018D2
SCREW FH
6
184
MFC04018D2
SCREW FH
4
185
013LR3014A
FRAME-FRONT TENSION,R
1
186
013LR3015A
FRAME-FRONT TENSION,L
1
187
141LR4022D
BRACKET-SAFETY COVER
1
22
RSH-1650
NO
Part N/O
Part Name
Q'TY
188
WPB15020A6
WASHER-PLAIN
2
189
RE000600D2
E-RING
1
190
381LR4036A
WIRE-T/FUSE,UP
1
191
140LR4005A
HOLDER-SLIP
1
192
141LR4015B
BRACKET-MICRO SWITCH
1
193
140LR4006A
HOLDER-SLIP(IN)
2
194
021LR1003A
COVER-TAKE UP,2
1
195
120LR4003A
SHAFT-SLIP
1
196
131LR4013A
SPROCKET-SLIP
1
197
147LR4007A
PAD-SLIP
1
198
131LR4014A
SPROCKET-SLIP(IN)
1
199
140LR4003A
HOLDER-SAFETY COVER
4
200
140LR4004C
HOLDER ASS'Y SAFETY COVER
1
201
140LR4004B
HOLDER ASS'Y SAFETY COVER
1
202
140LR4004A
HOLDER ASS'Y SAFETY COVER
1
203
140LR4004D
HOLDER ASS'Y SAFETY COVER
1
204
013LR4002A
SAFETY COVER FRAME-L
1
205
021LR3005A
SAFETY COVER
1
206
141LR4022A
BRACKET-SAFETY COVER
1
207
013LR4001A
SAFETY COVER FRAME-R
1
208
111LR4009A
BOLT- SAFETY COVER
1
209
138LR4010A
SPRING-SAFETY COVER
1
210
013LR3011A
FRAME-REWINDER,R
1
211
013LR3012A
FRAME-REWINDER,L
1
212
363LR4001D
BIMETAL-HEATER
2
213
TFH04018D2
SCREW FH
6
214
TFH04035D2
SCREW FH
8
215
381LR4037A
WIRE-T/FUSE,LO
1
216
010LR4001A
ENCODER-LENGTH SENSOR,A
1
217
141LR4023A
BRACKET-SENSOR PCB
1
218
381LR4042A
WIRE-EMER 2
1
219
350LR4002A
PCB-LENGTH ASS'Y
1
220
31300S002A
OPTICAL FIBER AMP
1
221
140LR4007A
HOLDER-SENSOR COUNT
1
222
2PC03006D2
SCREW TAP TITE PH
2
223
31400S001A
OPTICAL FIBER CABLE
1
224
141LR4024A
BRACKET-ENCODER
1
225
212LR1004A
STAND-BASE
2
226
021LR3006A
BRACKET-CLAMPER LEVER
1
227
12200X005A
BEARING-RADIAL TRUST
1
23
6.2 RSH-1050 Parts List
RSH-1050
NO
Part
PART NAME
Q'TY
1
13500X001A
CASTER-STAND1
2
2
13500X002A
CASTER-STAND2
2
3
WSB16038D0
WASHER-SPRING
4
4
212LR1003A
STAND-FRAME
2
5
212LR1005A
STAND-CENTER
1
6
BHE08015D2
BOLT
28
7
WSB08020D2
WASHER-SPRING
36
8
NHB08065D2
NUT
8
9
BHE08065D2
BOLT
8
10
212LR1004A
STAND-BASE
2
11
013LR2016A
FRAME-BASE
1
12
BHE06020D2
BOLT
8
13
WSB06015D2
WASHER-SPRING
4
14
MBC04008D2
SCREW BH
15
211003002B
BLOWER-ASS'Y
16
WSB04010D2
WASHER-SPRING
60
17
MFC04008D2
SCREW FH
15
18
141LR3001B
BRACKET-PCB
41
2
1
19
23200X001A
SUPPORT-B/K PCB
8
20
350LR3006D
PCB-MAIN ASS'Y
1
21
MBC05030D2
SCREW BH
8
22
34000S008A
POWER TRANSFORMER
1
23
013LR2021A
FRAME-R
1
24
013LR2020A
FRAME-L
1
25
013LR2009A
FRAME-FRONT
1
26
214LR3003A
MASH-FRAME,F
2
27
WSB03007D2
WASHER-SPRING
6
28
WPB04008D2
WASHER-PLAIN
5
29
WSB05013D2
WASHER-SPRING
30
RE000400D2
E-RING
1
31
013LR2017A
FRAME-CENTER
1
32
24000X003B
30
TAPE-TEFLON
1
33
21000S019A
MOTOR-MAIN
1
34
013LR2013B
FRAME-GUIDE,PAPER
1
35
142LR4002A
SPACER-GUIDE
2
36
133LR2012A
ROLLER-LAMI
2
37
122LR4008A
BUSH-ROLLER,LAMI LO
2
38
12200X012A
DU-BUSH
4
39
133LR2014A
ROLLER-PULL,LO
1
40
141LR2003A
PLATE-PRESSURE,L
1
41
141LR2004A
PLATE-PRESSURE,R
1
42
120LR3001A
SHAFT-CAM
1
43
122CR4002A
BEARING-CAM
2
44
RC000800C8
SNAP RING
2
45
124LR4002A
CAM-ROLLER Cu+Ni+Cr
2
24
RSH-1050
NO
Part
PART NAME
Q'TY
46
SKE05015D2
SCREW-SET
4
47
122LR4004A
BUSH-PLATE PRESSURE
6
48
RC001500C8
SNAP RING
7
49
133LR2013A
ROLLER-PULL,UP
1
50
122LR4007A
BUSH-ROLLER,LAMI UP
2
51
122LR4009A
BUSH-ROLLER,PULL UP
2
52
111LR4014A
BOLT-PRESSURE
4
53
WPB06016A6
WASHER-PLAIN
4
54
138LR4008A
SPRING-PRESSURE
4
55
120LR4001A
SHAFT-TABLE
1
56
363LR4001D
BIMETAL-HEATER
2
57
12200X016A
BEARING-IDLE,UP
4
58
141LR4012A
PLATE-BEARING
4
59
015LR3006A
BAR-IDLE
2
60
MPC03014D2
SCREW BH
4
61
12200X014A
DU BUSH
4
62
013LR2012A
FRAME-SENSOR
1
63
223LR2005B
HEATER ASS`Y
2
64
122LR4010A
BUSH-ROLLER,PULL LO
2
65
12200X013A
DU BUSH
4
66
12200X015A
DU BUSH
2
67
313LR3001A
SENSOR-ASS'Y
2
68
140LR4002A
HOLDER-SHAFT,T
1
69
381LR4032A
WIRE-REMOTE
1
70
12200X022A
BEARING-RADIAL TRUST
4
71
12200X005A
BEARING-RADIAL TRUST
1
72
MBC04018D2
SCREW BH
7
73
013LR3002A
FRAME-CUTTER
1
74
023LR3003A
KNOB-CUTTER,C
1
75
140LR3001A
HOLDER-CUTTER,C
1
76
213LR4001A
CUTTER-CROSS
1
77
138LR4001A
SPRING-CROSS,CUTTER
1
78
NHB03024D2
NUT
5
79
MPC03006D2
SCREW PH
3
80
12200X002A
DU BUSH
1
81
RC001000C8
SNAP RING
2
82
32500X0005
FUSE-MAIN
2
83
36600X002A
FUSE BLOCK
1
84
021LR3003A
CASE-SENSOR,UP
2
85
021LR3004A
CASE-SENSOR,LO
2
86
381LR4035B
WIRE-MOTOR
1
87
381LR4027A
WIRE-SENSOR
2
88
TFH04035D2
SCREW FH
8
89
111LR4004A
BOLT-CORE
8
90
141LR4010A
BRACKET-HEATER
2
91
120LR3004A
SHAFT-FILM,LO
1
92
143LR3001A
SUPPORTER-SHAFT,LO
1
93
141LR4005A
PLATE-SHAFT,FILM
3
25
RSH-1050
NO
Part
PART NAME
Q'TY
94
140LR4001A
HOLDER-SHAFT,FILM
2
95
147LR4002A
PAD-TENSION
2
96
141LR4011A
BRACKET-HEATER,STOPPER
4
97
12200X009A
DU BUSH
2
98
TFH04018D2
SCREW FH
6
99
138LR4002A
SPRING-FILM,TENSION
2
100
125LR4001A
HANDLE-TENSION
2
101
124LR3001A
CORE-57
6
102
142LR4001A
SPACER-HEATER,BKT
103
MBC04010D2
SCREW-BH
104
141LR4009A
BRACKET-REAR COVER
4
105
MBC05010D2
SCREW BH
8
106
MFC04018D2
SCREW FH
4
107
MFC05018D2
SCREW FH
6
108
MBC05018D2
SCREW BH
2
109
120LR4002A
SHAFT-TAKE UP
3
110
113LR4001A
WASHER TAKE UP
2
111
130LR4005A
GEAR-TAKE UP
1
112
141LR4006A
PLATE-SLIP
1
113
138LR4006A
SPRING-SLIP
2
114
WPB08016A6
WASHER-PLAIN
3
115
141LR4003A
BRACKET-MOTOR
1
116
130LR4004A
GEAR-MOTOR
1
117
RE000600D2
E-RING
1
4
10
118
21000S027A
MOTOR-AC
1
119
021LR2003A
COVER-TAKE UP,L
1
120
021LR2004A
COVER-TAKE UP,R
1
121
36400X003A
SWITCH-POWER
1
122
NHB05038D2
NUT
12
123
112004001C
NUT
1
124
014LR1003A
TABLE-FRONT
1
125
145LR3001A
GUIDE-DOCUMENT
2
126
111LR4006A
BOLT-GUIDE
2
127
023LR4002A
KNOB-BOLT,GUIDE
2
128
122LR4006A
BUSH-PULLEY
1
129
134LR4002A
PULLEY-CHAIN
1
130
BHE08045D2
BOLT
2
131
141LR4007A
BRACKET-SWITCH,EU
1
132
36400X002A
SWITCH-MAIN
1
133
36400X001A
SWITCH-EMERGENCY
2
134
23300X001A
BUSHING-CORD,EU
1
135
380CR4005A
POWER CORD -CUL
1
136
MBC04040D2
SCREW BH
4
137
SKE06010D2
SCREW-SET
1
138
SKE06015D2
SCREW-SET
1
139
SKE05010D2
SCREW-SET
2
140
021LR2001A
COVER-L
1
141
032LR4008A
SHEET-CUTTER
1
26
RSH-1050
NO
Part
PART NAME
Q'TY
142
MBC04006D2
SCREW BH
143
131LR4004A
SPROCKET-MOTOR
1
144
131LR4005A
SPROCKET-ROLLER,LAMI
1
145
NHB04032D2
NUT
2
146
SKE04015D2
SCREW-SET
2
147
131LR4006A
SPROCKET-ROLLER,PULL
1
148
SKE04008D2
SCREW-SET
2
149
WPB13025A6
WASHER-PLAIN
2
37
150
112004001B
NUT
1
151
136LR4002B
CHAIN-ROLLER
1
152
136LR4002A
CHAIN-ROLLER
1
153
011LR2004A
COVER-REAR
1
154
021LR2002A
COVER-R
1
155
032LR3004A
SHEET-FUNC
1
156
032LR4011A
SHEET-PRESSURE-CUL
1
157
023LR3006A
BUTTON-FUNC
1
158
350LR3007A
PCB-SUB ASS'Y
1
159
144LR4001A
CLAMPER-LEVER
1
160
125LR4003A
LEVER-PRESSURE
1
161
023LR4001A
KNOB-LEVER
1
162
1PC03006D2
SCREW TAP TATE PH
2
163
365LR4003A
SWITCH-FOOT ASS'Y
1
164
025LR4001A
CASE-REMOCON ASS'Y
1
165
350CR4001A
PCB-REMOCON ASS'Y
1
166
23300X008A
CABLE GRAND
2
167
147LR4001A
PAD-SLIP
1
168
123004001A
BALL
2
169
381LR4020B
WIRE-FUSE,EU
1
170
381LR4029B
WIRE-LO HEATER,EU
1
171
381LR4030B
WIRE-UP HEATER,EU
1
172
381LR4013A
WIRE-POWER S/W,EU
1
173
381LR4042B
WIRE-EMER 2
1
174
381LR4047B
WIRE-EMER
1
175
381LR4044A
WIRE-MAIN
1
176
141LR3004A
BRACKET-STAND
2
177
381LR4043A
WIRE-SAFETY SWITCH
1
178
381LR4045B
WIRE-LENGTH
1
179
381LR4046A
WIRE-COUNT
1
180
381LR4048A
WIRE-TAKE UP2
1
181
381LR4054A
WIRE-LO HEATER 2,EU
1
182
381LR4055A
WIRE-UP HEATER 2,EU
1
183
381LR4036A
WIRE-T/FUSE,UP
1
184
381LR4037A
WIRE-T/FUSE,LO
1
185
WPB15020A6
WASHER-PLAIN
2
186
36400X014A
SWITCH MICRO-SAFETY COVER
2
187
141LR4015A
BRACKET-MICRO SWITCH
1
188
141LR4022E
BRACKET-SAFETY COVER
1
189
12200X025A
BEARING-SLIP
2
27
RSH-1050
NO
Part
PART NAME
Q'TY
190
SKE04010D2
SCREW-SET
3
191
140LR4005A
HOLDER-SLIP
1
192
141LR4015B
BRACKET-MICRO SWITCH
1
193
140LR4006A
HOLDER-SLIP(IN)
1
194
021LR1003A
COVER-TAKE UP,2
1
195
120LR4003A
SHAFT-SLIP
1
196
131LR4013A
SPROCKET-SLIP
1
197
147LR4007A
PAD-SLIP
1
198
131LR4014A
SPROCKET-SLIP(IN)
1
199
140LR4003A
HOLDER-SAFETY COVER
4
200
140LR4004C
HOLDER ASS'Y SAFETY COVER
1
201
140LR4004B
HOLDER ASS'Y SAFETY COVER
1
202
140LR4004A
HOLDER ASS'Y SAFETY COVER
1
203
140LR4004D
HOLDER ASS'Y SAFETY COVER
1
204
013LR4002A
SAFETY COVER FRAME-L
1
205
021LR3005B
SAFETY COVER
1
206
141LR4022B
BRACKET-SAFETY COVER
1
207
013LR4001A
SAFETY COVER FRAME-R
1
208
111LR4009A
BOLT- SAFETY COVER
1
209
138LR4010A
SPRING-SAFETY COVER
1
210
138LR4014A
SPRING-HEATER
4
211
141LR4036A
BRACKET-SENSOR
1
212
120LR3003A
SHAFT-FILM,UP
1
213
021LR3006A
BRACKET-CLAMP LEVER
1
214
125LR4002A
HANDLE-LOCATION
1
215
141LR4024A
BRACKET-ENCODER
1
216
010LR4001A
ENCODER-LENGTH SENSOR,A
1
217
141LR4023A
BRACKET-SENSOR PCB
1
218
143LR4001A
STOPPER-LOCATION
1
219
350LR4002A
PCB-LENGTH ASS'Y
1
220
111LR4005A
BOLT-LOCATION,ADJUST
1
221
140LR4007A
HOLDER-SENSOR COUNT
1
222
143LR3002A
SUPPORTER-SHAFT,UP
1
223
31400S001A
OPTICAL FIBER CABLE
1
224
31300S002A
OPTICAL FIBER AMP
1
28
7. Exploded View
7.1 RSH-1650 Exploded View
Frame L
Frame R
Stand Part and Frame-Base
Frame,Roller and Other View
Wire and Film Shafts
Front Table and Shafts Cover
7.2 RSH-1050 Explode View
Frame L
Frame R
Stand Part and Frame-Base
Frame,Roller and Other View
Wire and Film Shafts
Front Table and Shafts Cover
29
7.1 RSH-1650 Exploded View
182
105
147
127
202
168
18 ~ 22
??
??
UP-HT
LO-HT
LOW-L
??
??
??
UP-L
??
??
7
6
??
??
??
??
??
< RSH-1650/1050 Main PCB Layout >
30
12200X005A
0 21LR 3006A
2 12LR 1004A
1 41LR 4024A
31400S001A
2PC03006D2
1 40LR 4007A
31300S002A
3 50LR 4002A
3 81LR 4042A
1 41LR 4023A
0 10LR 4001A
BEARING-RADIAL TRUST
NTB12*26
BRACKET-CLAMPER LEVER
STAND-BASE
STKR 125*50
BRACKET-ENCODER
S45C
OPTICAL FIBER CABLE, FT-420-10
SCREW TAP TATE PH; B-3*6
SUS
HOLDER-SENSOR COUNT
SPCC 0.5T
OPTICAL FIBER AMP
PCB-LENGTH ASS'Y
WIRE-EMER2
BRACKET-SENSOR PCB
SPCC 2T
SPCC 0.5T
ENCODER-LENGTH SENSOR,A
1
1
2
1
1
2
1
1
1
1
1
1
381LR4037A
TFH0403 5D2
TFH0401 8D2
3 63LR4001D
013LR3012A
013LR3011A
138LR4010A
111LR4009A
013LR4001A
141LR4022A
021LR3005A
013LR4002A
1 40LR4004D
140LR4004A
140LR4004B
1 40LR4004C
140LR4003A
131LR4014A
147LR4007A
131LR4013A
120LR4003A
021LR1003A
140LR4006A
141LR4015B
140LR4005A
381LR4036A
RE000600D2
WPB15020A6
1 41LR4022D
013LR3015A
013LR3014A
MFC04018D2
MFC05018D2
MBC0 501 8D2
3 6400X014A
141LR4015A
1 2200X025A
MPC0 301 4D2
2 4000X003A
1PC0300 6D2
381LR4044A
381LR4047A
381LR4054A
381LR4013B
381LR4030A
381LR4029A
381LR4020B
138LR4014A
381LR4055A
2 3300X008A
350CR4001A
025LR4001A
365LR4003A
MFC04008D2
023LR4001A
125LR4003A
144LR4001A
350LR3007A
023LR3006A
032LR4010A
032LR3004A
021LR2002A
011LR2003A
136LR4004A
136LR4004B
112004001B
MBC0 401 8D2
WPB13025A6
131LR4015A
147LR4001A
WPB04008D2
131LR4016A
131LR4004A
381LR4043A
032LR4008A
021LR2001A
SKE05 010D2
SKE06 015D2
SKE06 010D2
SKE05 015D2
380LR4001A
2 3300X001A
3 6400X001A
3 6400X002A
141LR4007A
BHE0 8045D2
134LR4002A
122LR4006A
SKE04 015D2
SKE04 010D2
145LR3001A
014LR1003B
112004001C
MBC04006D2
3 6400X003A
021LR2004A
021LR2003A
21000S027A
RE000400D2
130LR4004A
141LR4003A
WPB08016A6
138LR4006A
141LR4006A
130LR4005A
113LR4001A
120LR4002B
111LR4006A
023LR4002A
WSB05013D2
MBC05010D2
141LR4009A
MBC04040D2
142LR4001A
124LR3001A
125LR4001A
138LR4002A
WSB03007D2
12200X009A
141LR4011A
147LR4002A
140LR4001A
141LR4005A
143LR3001A
120LR3004B
141LR4016A
111LR4004A
381LR4048A
381LR4027E
381LR4035A
021LR3004A
021LR3003A
36600X002A
32500X0005
RC001000C8
12200X002A
MPC0 300 6D2
NHB0 3024D2
138LR4001A
213LR4001A
140LR3001A
023LR3003A
013LR3002B
381LR4045A
381LR4046A
12200X022A
381LR4032A
140LR4002A
313LR3001A
1 2200X015A
1 2200X013A
122LR4010A
223LR2003A
013LR2012B
1 2200X014A
1 2200X020A
015LR3005B
141LR4012A
1 2200X016A
015LR3005A
120LR4001B
NHB0 4032D2
WPB06016A6
111LR4014A
122LR4009A
122LR4007B
133LR2008A
R C00150 0C8
122LR4004A
SKE05 015D2
124LR4002A
R C00080 0C8
122CR4002A
120LR3002A
141LR2012A
141LR2011A
133LR2009A
1 2200X012A
122LR4008A
133LR2007B
142LR4002A
013LR2013A
2 1000S019A
NHB05038D2
013LR3005A
138LR4008A
141LR4036A
133LR2007A
138LR4009A
214LR3003A
013LR2009B
013LR2011A
013LR2010A
3 4000S008A
MBC0 401 0D2
350LR3006A
2 3200X001A
141LR3001B
WSB04010D2
MBC04008D2
211003002B
MBC0 503 0D2
WSB06015D2
BHE0 6020D2
013LR3006A
212LR2003A
BHE0 8100D2
NHB0 8065D2
WSB08020D2
BHE0 8015D2
2 12LR1005C
212LR1003A
WSB16038D0
1 3500X002A
1 3500X001A
WIRE-T/FUSE LOW(BLK)
SCREW FH ; 2-4*35
SCREW FH; 2-4*18
BIMETAL-HEATER
FRAME-REWINDER,L
FRAME-REWINDER,R
SPRING-SAFETY COVER
BOLT-SAFETY COVER
SAFETY COVER FRAME-R
BRACKET- SAFETY COVER
SAFETY COVER1741*159.7*3T
SAFETY COVER FRAME-L
HOLDER ASS'Y-SAFETY COVER
HOLDER ASS'Y-SAFETY COVER
HOLDER ASS'Y-SAFETY COVER
HOLDER ASS'Y-SAFETY COVER
HOL DER-SAFETY COVER
1
8
6
2
1
1
1
1
1
1
1
1
1
1
1
1
4
1
BLK
1
1
BLK
1
BLK
1
P ANTONE 431C
2
1
1
1
1
2
1
1
1
4
6
4
2
1
2
4
1
2
1
1
1
W IRE-POW ER S/W ,EU UL1050 AWG#14
1 BRN/BLU
WIRE-UP HEATER,EU TEFRON WIRE 018/50
2
RED
WIRE-LO HEATER,EU TEFRON WIRE 018/50
2
BLK
WIRE-FUSE;UL1015AWG#14
1
SPRING-HEATER
4
WIRE-UP HEATER 2
RED
1
CABLE-GRAND;PG-7
2
PCB-REMOCON ASS'Y
1
CASE-REMOCON ASS'Y
1
SWITCH-FOOT ASS 'Y;KH8012 KOINO
1
SCREW FH
M4*8
6
KNOB-LEVER
NYLON
1
BLK
LEVER-PRESSURE
S45C
1
SNC3
CLAMPER-LEVER
S45C
1
SNC3
PCB-SUB ASS'Y;FR-4
1
BUTTON-FUNC
SIL ICON
1
SHEET-PRESSURE;PC 0.3T
1
SHEET-FUNC;PC 0.3T
1
COVER-R;940V0
ABS AF-312
1 PAN 4 31C
COVER-REAR
AL6063
1 PAN 4 21U
CHAIN-ROLLER: 571.5
1
CHAIN-ROLLER;419.1
1
N UT ;HEXAGON LOCK T YPE NYLON M12*1.75
1
FZY
SCREW BH M4*18
SUS
7
WASHER-PLAIN;1 3* 24*2.5 FZY
3
FZY
SPROCKET-ROL LER,PULL;φ65
S45C
1
PAD-SLIP;NBR φ15.1*31* 3T
2
WASHER-PLAIN φ4.3*8*0.8
5
SPROCKET-ROL LER,LAMI;φ102.4
S45C
1
SPROCKET-MOTOR;RS2 5 φ44
S45C
1
WIRE-SAFETY S/W; UL1015 AWG#14
1
BLACK
SHEET-CUTTER;PC 0.18T
1
ZWP5
COVER-L;940V0
ABS AF-312
1 PAN 4 31C
SCREW-SET;M5 *10
2
FZB
SCREW-SET ;M6*15
1
FZB
SCREW-SET ;M6*10
1
FZB
SCREW-SET ; M5*15
4
FZB
POWER CORD;AC250V15A,LT-261B
1
BUSHING-CORD,EU;7NR32
1
SW ITC H-EM ERGENC Y;KH-2022ER KOINO
2
SWITCH-MAIN;8216 B/R I/O SIGNAL-NUX SPA
1
BRACKET-SWITCH,EU
SPCC
1 PAN 4 21U
BOLT;HEXA HEAD M8*45
1
SUS27
PULLEY-CHAIN
S45C
1
BUSH PULLEY
S45C
1
SCREW-SET ; M4*15
2
SUS27
SCREW-SET ;M4*10
3
SUS27
GUIDE-DOCUMENT;940 V0
ABS AF-312
2 GRAY 8U
TABL E-FRONT
AL6063
1 GRAY 8U
NUT;HEXAGON LOCK TYPE NYLON M10*1.25
1
FZY
SCREW BH
M4*6
37
SWITCH -POWER;SRA1001HWBB
1
COVER-TAKE UP,R;940V0
ABS AF-312
1 PAN 4 31C
COVER-TAKE UP,L;940V0
ABS AF-312
1 PAN 4 31C
MOTOR-AC;D AG-6302RSI; AC230V/50Hz
1
E-RING;ETW-4
1
GEAR-MOTOR;POM GV/30 φ35*33Z
2
BRACKET-MOTOR
SECC
1 PAN 421U
WASHER-PLAIN;8.5*25*1.6
3
FZY
SPRING-SLIPΦ3.5
SWRH
2
ZWP5
PLATE-SLIP;SECC φ36*2T
1
GEAR-TAKE UP ;POM GV/30 φ40*40Z
1
WAS HER-TAKE UP;MOST 16.0*34*0.5
4
SHAF-TAKE UP
S45C
1
SNC3
BOLT-GUIDE
S45C
2
KNOB-BOLT, GUIDE
PHENOL BLK 2
WASHER-SPRING φ5.1*1.3T
SWRH
30
FZY
SCREW BH M5*10
SUS
8
BRACKET-REAR COVER
4
SCREW BH M4*40
SUS
4
FZY
SPACER-HEATER,BKT
Φ4.6*Φ8*34
4
CORE-57
AL
6
HANDLE-TENSION
S45C
2
SNC3
SPRING-FILM,TENSION;φ3.8
SWRH
2
ZWP5
WASHER-SPRING; φ3*0.7
8
DU BUSH;FLANGE 15*20
2
BRAC KET-HEATER,STOPPER;NYLON66
4
PAD-TANSION;LEATHER 1.5T
2
HOLDER-SHAFT,FILM
S45C
2
SNC3
PLATE-SHAFT,FILM
SPCC
3
SNC3
SUPPORTER-SHAFT,LO
S45C
2
SNC3
SHAFT-FILM,LO
S45C
2
SNC3
BRACKET-HEATER ;EGI 0.2T
2
BOLT-CORE
S45C
8
SNC3
WIRE-TAKE UP2;UL1007AWG#20
1
WIRE-SENSOR
1
WIRE-MOTOR;UL1007AWG#18
1 BLK/RED
CASE-SENSOR,LO
2
CASE-SENSOR,UP
2
FUSE BLOCK
FB66
1
FUSE-MAIN
65TS AC250V 20A 2
SNAP-RING;STW-10
2
DU-BUSH;FLANGE 10*10
2
SCREW PH M3*6
SUS
6
FZW
NUT ; HEXAGON M3
2SORT
5
FZY
SPRING-CROSS,CUTTER ;φ0.3
SWRH
1
ZWP5
CUTTER-CROSS
STS420J2
1
HOLDER-CUTTER,C;94-VO
ABS AF-312
1 PAN 420U
KNOB-CUTTER,C;94-VO
ABS AF-312
1 PAN 420U
FRAME-CUTTER
AL6063
1 PAN 421U
WIRE-LENGTH
1
WIRE-COUNT; UL10 07 AWG#20
1
BEARING-RADIAL TRUST;NTB 15*28
5
WIRE-REMOTE;2464 24AWG4C
1
HOL DER-SHAFT,T
S45C
1
SNC3
SENSOR-ASS'Y
2
DU-BUSH ;W/O FLANGE 25*10
2
DU-BUSH ;FLANGE 25*25
4
BUSH-ROL LER,PULL LO
S45C
2
ZWP5
HEATER ASS'Y ;FCHW1 30.5Ω
2
FRAME-SENSOR
AL6063
1 PAN 4 21U
DU-BUSH ;W/O FLANGE 40*10
2
BEARIN G-IDLE,LO #6004Z
2
BAR-IDLE,LO ;φ40
S45C
1
SNC3
PLATE-BEARING;2T
SECC
2
ZWP5
BEARING-IDLE,UP #6201Z
2
BAR-IDLE,UP ;φ30
S45C
1
SNC3
SHAFT-TABL E;? 10
S45C
1
ZWP5
NUT HEXAGON M4
2
WASHER-PLAIN; φ6.6 *12 .5*1.6
4
FZY
BOLT-PRESSURE(M* N=11 *27.5) SUS; M10 P1.5 4
BUSH-ROL LER,PULL UP
S45C
2
ZWP5
BUSH-ROL LER,LAMI UP
S45C
2
ZWP5
ROLLER-PULL,UP ;φ60.0
S45C
1
SNC3
SNAP RING ;STW-15
8
BUSH-PLATE PRESSURE
MSWR3 M10 P1.5 6
ZWP5
SCREW-SET;M5 *15
4
FZB
CAM-ROLLER
S45C
2
ZWP5
SNAP RING ;STW-8
2
BEARING-CAM;#608Z
2
SHAFT-CAM :φ15
S45C
1
ZWP5
PLATE-PRESSURE,R ;3T
SPCC
1
ZWP5
PLATE-PRESSURE,L ;3T
SPCC
1
ZWP5
ROL LER-PULL,LO ;φ6 0.0
S45C
1
SNC3
DU-BUSH ;FLANGE 40*25
4
BUSH-ROL LER,LAMI LO
S45C
2
ZWP5
ROL LER-LAMI UP ;φ95.0
S45C
1
SNC3
SPACER-GUIDEΦ5.2*Φ7*15.8
2
FRAME-GUIDE,PAPER
AL6063
1 PAN. 421U
MOTOR-MAIN;DS09-04 0-3 002 180:1
1
NUT M5
HEXAGON
12
FRAME-CENTER;
AL6063
1 PAN. 421U
SPRING-PRESSURE; φ3.0
SWRH
4
BRACKET-SENSOR
1
ROLLER-LAMI LO ; φ96.0
S45C
1
SPRING-HEATER SUPPORT
6
MASH-FRAME,F;2T
SPCC
3 PAN. 421U
FRAME-FRONT;
AL6063
1 PAN. 421U
FRAME-R 4.5T
SPCC
1 PAN. 421U
FRAME-L 4.5T
SPCC
1 PAN. 421U
POWER TRANSFORMER
1
SCREW BH ; M4*10
SUS
12
PCB-MAIN ASS'Y
FR4
1
SUPPORT-BRACKET PCB
DASS-9N
10
BRACKET-PCB;1.6T
SECC
1
ZWP5
WASHER-SPRING ; φ4.1*1.0T
SWRH
52
FZY
SCREW BH ; M4*8
SUS
45
BLOWER ASS'Y
PF-RS6225
3
SCREW BH ; M5*30
SUS
10
WASHER-SPRING ;φ6.1*1.5T
SWRH
10
FZY
BOLT;HEXA HEAD M6*20
14
FZB
FRAME-BASE;
AL6063
1 PAN. 421U
STAND-TOP
STKR
1 GRAY 8U
BOLT;HEXA HEAD M8*100
8
FZB
NUT;HEXAGON M8
8
FZY
WASHER-SPRING; φ8.2*2T
SWRH
28
BOLT;HEXA HEAD M8*15
20
SUS
STAND-CENTER;STKR 125*50
1
STAND-FRAME;STKR 125*50
2
WASHER-SPRING
Φ16.2*3.8T
4
CASTER-STAND2
20-30S-B3-SBB 2 N,BRAKE
CASTER-STAND1
20-30S-B3-SBB 2
BRAKE
100℃
SPCC 4.5T
SPCC 4.5T
SWRH
S45C
SPCC
AL-6063
PC PLATE
SPCC
S45C
S45C
S45C
S45C
S45C
SPROCKET-SLIP IN :P.C.D39.8, Z=13T
S45C
PAD-SLIP; O.D 24, I.D 1 2.4, 4t
SPROCKET-SLIP:P.C.D39.8, Z=13T
S45C
SHAFT-SL IP:Φ12
S45C
COVER-TAKE UP2
ABS 94V-0
H OLD ER-SLIP(IN): O.D 54, I.D 11 10T
S45C
BRACKET-MICRO SWITCH,S
SECC
HOL DER-SLIP:O.D54, I.D 1 1 10T
S45C
WIRE-T/FUSE UP(RED)
E-RING; ETW-6 WON IL
WASHER-PLAIN
15.5*28*2T
BRACKET-SAFETY COVER
AL-6063
FRAME-FRONT TENSION L
FRAME-FRONT TENSION R
SCREW FH;M4*18
SUS
SCREW FH; M5*18
SCREW BH M5*18
SUS
SWITCH -MICRO SAFETY COVER
VP531-2H
BRACKET-MICRO SWITCH,G
SECC 1.2T
BEARING-SLIP
#6000Z
SCREW PH M3*14
SUS
TAPE-TEFLON;1745*55mm*0.1T
SCREW TAP TATE PH
S-3*6 FZY
WIR E-MAIN;26 AWG20C
WIRE-EMER;UL 1007AWG#20 4P
WIRE-LO HEATER 2,
BLK
1st GRADE FATAL DEFECT
2nd GRADE FATAL DEFECT
IMPORTANCE OF QUALITY
0
3rd GRADE MEDIUM DEFECT
0
4th GRADE SLIGHTLY DEFECT
TOTAL
IMPORTANCE OF QUALITY
0
T.I.Q
0
TOTAL
RSH-1650
~6
7 ~ 30
0.08
0.1
31 ~ 120
0.2
1 21 ~ 300
0.4
3 01 ~ 600
0.6
601 ~ 1200
0.8
N/S
EXPLODE VIEW
Frame - L
83
13. Remote Control and Foot Pedal wires.
31
No.
Part No.
16
17
19
23
30
32
40
43
44
45
46
47
48
52
53
58
78
82
83
90
96
102
103
105
106
119
126
131
132
133
134
135
140
141
145
162
168
178
180
181
192
216
217
219
224
MBC04008D2
WSB04010D2
23200X001A
013LR2010A
138LR4008A
NHB05038D2
141LR2011A
122CR4002A
RC000800C8
124LR4002A
SKE05015D2
122LR4004A
RC001500C8
111LR4014A
WPB06016A6
141LR4012A
NHB03024D2
32500X0005
36600X002A
141LR4016A
141LR4011A
142LR4001A
MBC04040D2
MBC05010D2
WSB05013D2
021LR2003A
SKE04010D2
141LR4007A
36400X002A
36400X001A
23300X001A
380LR4001A
021LR2001A
032LR4008A
WPB04008D2
MFC04008D2
138LR4014A
MPC03014D2
141LR4015A
36400X014A
141LR4015B
010LR4001A
141LR4023A
350LR4002A
141LR4024A
Part
Name
SCREW BH
WASHER-SPRING
SUPPORT-B/K PCB
FRAME-L
SPRING-PRESSURE
NUT
PLATE-PRESSURE,L
BEARING-CAM
SNAP RING
CAM-ROLLE Cu+Ni+Cr
SCREW-SET
BUSH-PLATE PRESSURE
SNAP RING
BOLT-PRESSURE
WASHER-PLAIN
PLATE-BEARING
NUT-BRACKET SWITCH
FUSE-MAIN
FUSE BLOCK
BRACKET-HEATER
BRACKET-HEATER,STOPPER
SPACER-HEATER,BKT
SCREW BH
SCREW BH
WASHER-SPRING
COVER-TAKE UP,L
SCREW-SET
BRACKET-SWITCH,EU
SWITCH-MAIN
SWITCH-EMERGENCY
BUSHING-CORD,EU
POWER CORD-EU
COVER-L
SHEET-CUTTER
WASHER-PLAIN
SCREW FH
SPRING-HEATER
SCREW PH
BRACKET-MICRO SWITCH
SWITCH MICRO-SAFETY COVER
BRACKET-MICRO SWITCH
ENCODER-LENGTH SENSOR,A
BRACKET-SENSOR PCB
PCB-LENGTH ASS'Y
BRACKET-ENCODER
Frame - R
127
168
32
No.
Part No.
12
16
17
21
24
30
32
41
43
44
45
46
47
48
52
53
58
70
79
81
90
96
98
99
100
102
103
105
106
111
112
113
114
115
116
118
120
121
123
126
127
128
129
130
133
136
137
138
139
143
144
145
146
147
148
149
150
151
152
154
155
156
157
158
159
160
161
168
179
182
188
189
191
193
194
195
196
197
198
212
222
226
227
BHE06020D2
MBC04008D2
WSB04010D2
MBC04010D2
013LR2011A
138LR4008A
NHB05038D2
141LR2012A
122CR4002A
RC000800C8
124LR4002A
SKE05015D2
122LR4004A
RC001500C8
111LR4014A
WPB06016A6
141LR4012A
12200X022A
MPC03006D2
RC001000C8
141LR4016A
141LR4011A
WSB03007D2
138LR4002A
125LR4001A
142LR4001A
MBC04040D2
MBC05010D2
WSB05013D2
130LR4005A
141LR4006A
138LR4006A
WPB08016A6
141LR4003A
130LR4004A
21000S027A
021LR2004A
36400X003A
112004001C
SKE04010D2
SKE04015D2
122LR4006A
134LR4002A
BHE08045D2
36400X001A
SKE05015D2
SKE06010D2
SKE06015D2
SKE05010D2
131LR4004A
131LR4016A
WPB04008D2
147LR4001A
131LR4015A
WPB13025A6
MBC04018D2
112004001B
136LR4004B
136LR4004A
021LR2002A
032LR3004A
032LR4010A
023LR3006A
350LR3007A
144LR4001A
125LR4003A
023LR4001A
138LR4014A
12200X025A
MBC05018D2
WPB15020A6
RE000600D2
140LR4005A
140LR4006A
021LR1003A
120LR4003A
131LR4013A
147LR4007A
131LR4014A
363LR4001D
2PC03006D2
021LR3006A
12200X005A
Part
Name
BOLT
SCREW BH
WASHER-SPRING
SCREW-BH
FRAME-R
SPRING-PRESSURE
NUT
PLATE-PRESSURE,R
BEARING-CAM
SNAP RING
CAM-ROLLE Cu+Ni+Cr
SCREW-SET
BUSH-PLATE PRESSURE
SNAP RING
BOLT-PRESSURE
WASHER-PLAIN
PLATE-BEARING
BEARING-RADIAL TRUST
SCREW PH
SNAP RING
BRACKET-HEATER
BRACKET-HEATER,STOPPER
WASHER-SPRING
SPRING-FILM,TENSION
HANDLE-TENSION
SPACER-HEATER,BKT
SCREW BH
SCREW BH
WASHER-SPRING
GEAR-TAKE UP
PLATE-SLIP
SPRING-SLIP
WASHER-PLAIN
BRACKET-MOTOR
GEAR-MOTOR
MOTOR-AC
COVER-TAKE UP,R
SWITCH-POWER
NUT
SCREW-SET
SCREW-SET
BUSH-PULLEY
PULLEY-CHAIN
BOLT
SWITCH-EMERGENCY
SCREW-SET
SCREW-SET
SCREW-SET
SCREW-SET
SPROCKET-MOTOR
SPROCKET-ROLLER,LAMI
WASHER-PLAIN
PAD-SLIP
SPROCKET-ROLLER,PULL
WASHER-PLAIN
SCREW BH
NUT
CHAIN-ROLLER
CHAIN-ROLLER
COVER-R
SHEET-FUNC
SHEET-PRESSURE-EU,AU
BUTTON-FUNC
PCB-SUB ASS'Y
CLAMPER-LEVER
LEVER-PRESSURE
KNOB-LEVER
SPRING-HEATER
BEARING-SLIP
SCREW BH
WASHER-PLAIN
E-RING
HOLDER-SLIP
HOLDER-SLIP(IN)
COVER-TAKE UP,2
SHAFT-SLIP
SPROCKET-SLIP
PAD-SLIP
SPROCKET-SLIP(IN)
BIMETAL-HEATER
SCREW TAP TITE PH
BRACKET-CLAMPER LEVER
BEARING-RADIAL TRUST
Stand Part and Frame - Base
17
7
6
7
4
7
225
No. Part No.
3
2
7
5
3
1
6
4
225
3
2
3
1
33
7
6
1
2
3
4
5
6
7
8
9
10
11
12
13
15
16
17
18
19
20
21
22
26
33
69
122
163
164
165
166
176
220
225
13500X001A
13500X002A
WSB16038D0
212LR1003A
212LR1005C
BHE08015D2
WSB08020D2
NHB08065D2
BHE08100D2
212LR2003A
013LR3006A
BHE06020D2
WSB06015D2
211003002B
MBC04008D2
WSB04010D2
141LR3001B
23200X001A
350LR3006A
MBC04010D2
34000S008A
214LR3003A
21000S019A
381LR4032A
MBC04006D2
365LR4003A
025LR4001A
350CR4001A
23300X008A
1PC03006D2
31300S002A
212LR1004A
Part
Name
CASTER-STAND1
CASTER-STAND2
WASHER-SPRING
STAND-FRAME
STAND-CENTER
BOLT
WASHER-SPRING
NUT
BOLT
STAND TOP
FRAME-BASE
BOLT
WASHER-SPRING
BLOWER-ASS'Y
SCREW BH
WASHER-SPRING
BRACKET-PCB
SUPPORT-B/K PCB
PCB-MAIN ASS'Y
SCREW-BH
POWER TRANSFORMER
MASH-FRAME,F
MOTOR-MAIN
WIRE-REMOTE
SCREW BH
SWITCH-FOOT ASS'Y
CASE-REMOCON ASS'Y
PCB-REMOCON ASS'Y
CABLE GRAND
SCREW TAP TATE PH
OPTICAL FIBER AMP
STAND-BASE
Frame, Roller and Other View
34
No.
Part No.
14
16
17
21
23
24
25
27
28
29
31
34
35
36
37
38
39
42
49
50
51
55
56
57
59
60
61
62
63
64
65
66
67
68
70
73
74
75
76
77
78
79
84
85
87
93
94
95
104
105
106
126
149
153
162
177
199
200
201
202
203
214
221
223
MBC05030D2
MBC04008D2
WSB04010D2
MBC04010D2
013LR2010A
013LR2011A
013LR2009B
138LR4009A
133LR2007A
141LR4036A
013LR3005A
013LR2013A
142LR4002A
133LR2007B
122LR4008A
12200X012A
133LR2009A
120LR3002A
133LR2008A
122LR4007B
122LR4009A
120LR4001B
015LR3005A
12200X016A
015LR3005B
12200X020A
12200X014A
013LR2012B
223LR2003A
122LR4010A
12200X013A
12200X015A
313LR3001A
140LR4002A
12200X022A
013LR3002B
023LR3003A
140LR3001A
213LR4001A
138LR4001A
NHB03024D2
MPC03006D2
021LR3003A
021LR3004A
381LR4027E
141LR4005A
140LR4001A
147LR4002A
141LR4009A
MBC05010D2
WSB05013D2
SKE04010D2
MBC04018D2
011LR2003A
MFC04008D2
24000X003A
140LR4003A
140LR4004C
140LR4004B
140LR4004A
140LR4004D
TFH04035D2
140LR4007A
31400S001A
Part
Name
SCREW BH
SCREW BH
WASHER-SPRING
SCREW-BH
FRAME-L
FRAME-R
FRAME-FRONT
SPRING-HEATER SUPPORT
ROLLER-LAMI, LO
BRACKET-SENSOR
FRAME-CENTER
FRAME-GUIDE,PAPER
SPACER-GUIDE
ROLLER-LAMI, UP
BUSH-ROLLER,LAMI LO
DU-BUSH
ROLLER-PULL,LO
SHAFT-CAM
ROLLER-PULL,UP
BUSH-ROLLER,LAMI UP
BUSH-ROLLER,PULL UP
SHAFT-TABLE
BAR-IDLE,UP
BEARING-IDLE
BAR-IDLE,LO
BEARING-IDLE,LO
DU BUSH
FRAME-SENSOR
HEATER-ASS'Y
BUSH-ROLLER,PULL LO
DU BUSH
DU BUSH
SENSOR-ASS'Y
HOLDER-SHAFT,T
BEARING-RADIAL TRUST
FRAME-CUTTER
KNOB-CUTTER,C
HOLDER-CUTTER,C
CUTTER-CROSS
SPRING-CROSS,CUTTER
NUT-BRACKET SWITCH
SCREW PH
CASE-SENSOR,UP
CASE-SENSOR,LO
WIRE-SENSOR
PLATE-SHAFT,FILM
HOLDER-SHAFT,FILM
PAD-TENSION
BRACKET-REAR COVER
SCREW BH
WASHER-SPRING
SCREW-SET
SCREW BH
COVER-REAR
SCREW FH
TAPE-TEFLON
HOLDER-SAFETY COVER
HOLDER ASS'Y SAFETY COVER
HOLDER ASS'Y SAFETY COVER
HOLDER ASS'Y SAFETY COVER
HOLDER ASS'Y SAFETY COVER
SCREW FH
HOLDER-SENSOR COUNT
OPTICAL FIBER CABLE
Wire and Film Shafts
No. Part No.
16
48
54
80
81
89
91
92
97
101
107
108
109
117
124
125
145
187
204
205
206
207
208
209
35
MBC04008D2
RC001500C8
NHB04032D2
12200X002A
RC001000C8
111LR4004A
120LR3004B
143LR3001A
12200X009A
124LR3001A
023LR4002A
111LR4006A
120LR4002B
RE000400D2
014LR1003B
145LR3001A
WPB04008D2
141LR4022D
013LR4002A
021LR3005A
141LR4022A
013LR4001A
111LR4009A
138LR4010A
Part
Name
SCREW BH
SNAP RING
NUT
DU BUSH
SNAP RING
BOLT-CORE
SHAFT-FILM,LO
SUPPORTER-SHAFT,LO
DU BUSH
CORE-57
KNOB-BOLT,GUIDE
BOLT-GUIDE
SHAFT-TAKE UP
E-RING
TABLE-FRONT
GUIDE-DOCUMENT
WASHER-PLAIN
BRACKET-SAFETY COVER
SAFETY COVER FRAME-L
SAFETY COVER
BRACKET-SAFETY COVER
SAFETY COVER FRAME-R
BOLT- SAFETY COVER
SPRING-SAFETY COVER
Front Table and Safety Cover
68
105
No. Part No.
LOW-L
LO-HT
UP-L
UP-HT
??
??
??
??
??
??
??
??
??
36
??
??
??
12
13
68
70
71
72
86
88
93
94
95
105
106
111
112
113
114
123
142
146
162
167
169
170
171
172
173
174
175
185
186
190
210
211
213
215
218
BHE06020D2
WSB06015D2
140LR4002A
12200X022A
381LR4046A
381LR4045A
381LR4035A
381LR4048A
141LR4005A
140LR4001A
147LR4002A
MBC05010D2
WSB05013D2
130LR4005A
141LR4006A
138LR4006A
WPB08016A6
112004001C
381LR4043A
147LR4001A
MFC04008D2
381LR4055A
381LR4020B
381LR4029A
381LR4030A
381LR4013B
381LR4054A
381LR4047A
381LR4044A
013LR3014A
013LR3015A
381LR4036A
013LR3011A
013LR3012A
TFH04018D2
381LR4037A
381LR4042A
Part
Name
BOLT
WASHER-SPRING
HOLDER-SHAFT,T
BEARING-RADIAL TRUST
WIRE-COUNT
WIRE-LENGTH
WIRE-MOTOR
WIRE-TAKE UP2
PLATE-SHAFT,FILM
HOLDER-SHAFT,FILM
PAD-TENSION
SCREW BH
WASHER-SPRING
GEAR-TAKE UP
PLATE-SLIP
SPRING-SLIP
WASHER-PLAIN
NUT
WIRE-SAFETY SWITCH
PAD-SLIP
SCREW FH
WIRE-UP HEATER 2,EU
WIRE-FUSE,EU
WIRE-LO HEATER,EU
WIRE-UP HEATER,EU
WIRE-POWER S/W,EU
WIRE-LO HEATER 2,EU
WIRE-EMER
WIRE-MAIN
FRAME-FRONT TENSION,R
FRAME-FRONT TENSION,L
WIRE-T/FUSE,UP
FRAME-REWINDER,R
FRAME-REWINDER,L
SCREW FH
WIRE-T/FUSE,LO
WIRE-EMER 2
7.2 RSH-1050 Exploded View
48
18 ~ 22
1
2
3
4
180
181
182
< RSH-1650/1050 Main PCB Layout >
37
31300S002A
31400S001A
143LR3002A
140LR4007A
111LR4005A
350LR4002A
143LR4001A
141LR4023A
010LR4001A
141LR4024A
125LR4002A
021LR3006A
120LR3003A
141LR4036A
138LR4014A
138LR4010A
111LR4009A
013LR4001A
141LR4022B
021LR3005B
013LR4002A
OPTICAL FIBER AMP
OPTICAL FIBER CABLE, FT-420-10
SUPPORTER-SHAFT UP
HOLDER-SENSOR COUNT
BOLT-LOCATION ADJUST
PCB-LENGTH ASS'Y
STOPPER-LOCATION
BRACKET-SENSOR PCB
ENCODER-LENGTH SENSOR,A
RACKET-ENCODER
HANDLE-LOCATION
BRACKET-CLAMP LEVER
SHAFT-FILM, UP
BRACKET-SENSOR
SPRING-HEATERΦ0.6
SPRING-SAFETY COVER
BOLT-SAFETY COVER
SAFETY COVER FRAME-R
BRACKET- SAFETY COVER
SAFETY COVER
SAFETY COVER FRAME-L
BF3RX
S45C
SPCC 0.5T
S45C
S45C
SPCC 2T
SPCC 0.5T
S45C
S45C
S45C
S45C
SWRH
S45C
SPCC
AL-6063
PC PLATE
SPCC
1
1
1
1
1
1
1
1
1
1
1
1
1 Cu+Ni+Cr
1
4
1
1
1
1
1
1
140LR4004D
140LR4004A
140LR4004B
140LR4004C
140LR4003A
131LR4014A
147LR4007A
131LR4013A
120LR4003A
021LR1003A
140LR4006A
141LR4015B
140LR4005A
SKE04010D2
12200X025A
141LR4022E
141LR4015A
36400X014A
WPB15020A6
381LR4037A
381LR4036A
381LR4055A
381LR4054A
381LR4048A
381LR4046A
381LR4045B
381LR4043A
141LR3004A
381LR4044A
381LR4047B
381LR4042B
381LR4013A
381LR4030B
381LR4029B
381LR4020B
123004001A
147LR4001A
23300X008A
350CR4001A
025LR4001A
365LR4003A
1PC03006D2
023LR4001A
125LR4003A
144LR4001A
350LR3007A
023LR3006A
032LR4011A
032LR3004A
021LR2002A
011LR2004A
136LR4002A
136LR4002B
112004001B
WPB13025A6
SKE04008D2
131LR4006A
SKE04015D2
NHB04032D2
131LR4005A
131LR4004A
MBC04006D2
032LR4008A
021LR2001A
SKE05010D2
SKE06015D2
SKE06010D2
MBC04040D2
380CR4005A
23300X001A
36400X001A
36400X002A
141LR4007A
BHE08045D2
134LR4002A
122LR4006A
023LR4002A
111LR4006A
145LR3001A
014LR1003A
112004001C
NHB05038D2
36400X003A
021LR2004A
021LR2003A
21000S027A
RE000600D2
130LR4004A
141LR4003A
WPB08016A6
138LR4006A
141LR4006A
130LR4005A
113LR4001A
120LR4002A
MBC05018D2
MFC05018D2
MFC04018D2
MBC05010D2
141LR4009A
MBC04010D2
142LR4001A
124LR3001A
125LR4001A
138LR4002A
TFH04018D2
12200X009A
141LR4011A
147LR4002A
140LR4001A
141LR4005A
143LR3001A
120LR3004A
141LR4010A
111LR4004A
TFH04035D2
381LR4027A
381LR4035B
021LR3004A
021LR3003A
36600X002A
32500X0005
RC001000C8
12200X002A
MPC03006D2
NHB03024D2
138LR4001A
213LR4001A
140LR3001A
023LR3003A
013LR3002A
MBC04018D2
12200X005A
12200X022A
381LR4032A
140LR4002A
313LR3001A
12200X015A
12200X013A
122LR4010A
223LR2005B
013LR2012A
12200X014A
MPC03014D2
015LR3006A
141LR4012A
12200X016A
363LR4001D
120LR4001A
138LR4008A
WPB06016A6
111LR4014A
122LR4009A
122LR4007A
133LR2013A
RC001500C8
122LR4004A
SKE05015D2
124LR4002A
RC000800C8
122CR4002A
120LR3001A
141LR2004A
141LR2003A
133LR2014A
12200X012A
122LR4008A
133LR2012A
142LR4002A
013LR2013B
21000S019A
24000X003B
013LR2017A
RE000400D2
WSB05013D2
WPB04008D2
WSB03007D2
214LR3003A
013LR2009A
013LR2020A
013LR2021A
34000S008A
MBC05030D2
350LR3006D
23200X001A
141LR3001B
MFC04008D2
WSB04010D2
211003002B
MBC04008D2
WSB06015D2
BHE06020D2
013LR2016A
212LR1004A
BHE08065D2
NHB08065D2
WSB08020D2
BHE08015D2
212LR1005A
212LR1003A
WSB16038D0
13500X002A
13500X001A
S45C
S45C
S45C
S45C
S45C
S45C
PAD-SLIP : O.D 24, I.D 12 4t
SPROCKET-SLIP:P.C.D44, Z=13T
S45C
SHAFT-SLIP: DIA 12
S45C
COVER-TAKE UP2
ABS 94V-0
HOLDER-SLIP(IN): O.D54, I.D 10
S45C
BRACKET-MICRO SWITCH,S
SECC
HOLDER-SLIP:O.D54, I.D10
S45C
SCREW-SET M4*10
FZB
BEARING-SLIP GMB#6000Z
BRACKET-SAFETY COVER
AL6063
BRACKET-MICRO SWITCH,G
SECC 1.2T
SWITCH-MICRO SAFETY COVER AC250V 16A KW3A
WASHER-PLAIN; 15*28*2T
WIRE-T/FUSE LO; UL1015 AWG#14
WIRE-T/FUSE UP; UL1015 AWG#14
1
1
1
1
4
1
BLK
1
1
BLK
1
BLK
1 PANTONE 431C
1
1
1
3
2
1
1
2
2
1
BLK
1
RED
WIRE-UP HEATER2; UL1015 AWG#14
1
RED
WIRE-LO HEATER2; UL1015 AWG#14
1
BLK
WIRE-TAKE UP2; UL1007 #20
1
WIRE-COUNT; UL 1007 AWG#20 5P
1
WIRE-LENGTH; 2464 24AWG (6C)SB242
1
WIRE-SAFETY S/W;UL1015 AWG#14
1
BLK
BRACKET-STAND
SPCC
2
WIRE-MAIN;2646 SB 26AWG 20C
1
WIRE-EMER;UL 1007AWG#20 4P
1
WIRE- EMER2; UL1007 AWG#20
1
WHT
WIRE-POWER S/W,UL1015 AWG#14
1 BLK/RED
WIRE-UP HEATER,EU TEFRON WIRE 018/50
1
RED
WIRE-LO HEATER,EUTEF RON WIRE 018/50
1
BLK
WIRE-FUSE;UL1050AWG#14
1
BALL Φ6
2
PAD-SLIP; 15.1*31*3
NBR
1
CABLE-GRAND;PG-7
2
PCB-REMOCON ASS'Y;
1
CASE-REMOCON ASS'Y
1
SWITCH-FOOT ASS'Y;KH8012 KOINO
1
SCREW TAP TATE PH;S-3*6 SUS27
2
KNOB-LEVER
NYLON
1
BLK
LEVER-PRESSURE
S45C
1
SNC3
CLAMPER-LEVER
S45C
1
SNC3
PCB-SUB ASS'Y;FR-4
1
BUTTON-FUNC
SILICON
1
SHEET-PRESSURE;PC 0.3T
1
SHEET-FUNC;PC 0.3T
1
COVER-R;940V0
ABS AF-312
1 PAN 431C
COVER-REAR
AL6063
1 PAN 421U
CHAIN-ROLLER 533.4
1
CHAIN-ROLLER;491.1
1
NUT;HEXAGON LOCK TYPE NYLON M12*1.75
1
FZY
WASHER-PLAIN; 13*24*2.5 FZY
2
SCREW-SET; M4*8
2
SPROCKET-ROLLER,PULL;φ65 20T S45C
1
SCREW-SET; M4*15
2
NUT; M4
2
SPROCKET-ROLLER,LAMI;φ87 27T
S45C
1
SPROCKET-MOTOR;RS25 φ44
S45C
1
SCREW BH; M4*6
SUS
37
SHEET-CUTTER;PC 0.18T
1
ZWP5
COVER-L;940V0
ABS AF-312
1 PAN 431C
SCREW-SET;M5*10
2
FZB
SCREW-SET ;M6*15
1
FZB
SCREW-SET ;M6*10
1
FZB
SCREW BH; M4*40
SUS
4
POWER CORD;AC250V15A,LT261B
1
BUSHING-CORD,EU;7NR32
1
SWITCH-EMERGENCY;KH-2022ER KOINO
2
SWITCH-MAIN;8216 B/R I/O SIGNAL-NUX SPA
1
BRACKET-SWITCH,EU
SPCC
1 PAN 421U
BOLT;HEXA HEAD M8*45
2
FZB
PULLEY-CHAIN
S45C
1
BUSH PULLEY
S45C
1
KNOB-BOLT,GUIDE
PHENOL
2
BLK
BOLT-GUIDE;4*22.5
S45C
2
SNC3
GUIDE-DOCUMENT;940V0
ABS AF-312
2 GRAY 8U
TABLE-FRONT
AL6063
1 GRAY 8U
NUT;HEXAGON LOCK TYPE NYLON M10*1.25
1
FZY
NUT; M5
12
SWITCH-POWER;SRA1001HWBB
1
COVER-TAKE UP,R;940V0
ABS AF-312
1 PAN 431C
COVER-TAKE UP,L;940V0
ABS AF-312
1 PAN 431C
MOTOR-AC;DAG-6302RSI; AC230V/50Hz
1
E-RING;ETW-6
1
GEAR-MOT OR;POM GV/30 φ33*33Z
1
BRACKET-MOTOR
SECC
1
WASHER-PLAIN;8.5*25*1.6
3
FZY
SPRING-SLIP
SWRH
2
ZWP5
PLATE-SLIP;SECC φ36*2T
1
GEAR-T AKE UP;POM GV/30 φ60*60Z
1
WASHER-TAKE UP;MOST 16*34*0.5
2
SHAFT TAKE UP
S45C
3
SNC3
SCREW BH; M5*18
SUS
2
SCREW FH; M5*18
SUS
6
SCREW FH; M4*18
SUS
4
SCREW BH; M5*10
SUS
8
BRACKET-REAR COVER
S45C
4
SCREW BH; M4*10
SUS
10
SPACER-HEATER,BKT
4
CORE-57
AL
6
HANDLE-TENSION
S45C
2
SNC3
SPRING-FILM,TENSION;φ3.8
SWRH
2
ZWP5
SCREW FH; 2-4*18
SUS
6
DU BUSH;FLANGE 15*20
2
BRACKET-HEATER,STOPPER;NYLON66
4
PAD-TENSION;LEATHER 1.5T
2
HOLDER-SHAFT,FILM
S45C
2
SNC3
PLATE-SHAFT,FILM
SPCC
3
SNC3
SUPPORTER-SHAFT,LO
S45C
1
SNC3
SHAFT-FILM,LO
S45C
1
SNC3
BRACKET-HEATER
SFCC1.6T
2
BOLT-CORE
S45C
8
SNC3
SCREW FH; 2-4*35
SUS
8
WIRE-SENSOR
2
WIRE-MOTER;UL1007AWG#18
1 BLK/RED
CASE-SENSOR,LO
2
CASE-SENSOR,UP
2
FUSE BLOCK
FB66
1
FUSE-MAIN
65TS AC250V 20A 2
SNAP-RING;STW-10
2
DU-BUSH;FLANGE 10*10
1
SCREW PH M3*6
SUS
3
NUT ; HEXAGON M3 2SORT
5
FZY
SPRING-CROSS,CUTTER ;φ0.3
SWRH
1
ZWP5
CUTTER-CROSS
STS420J2
1
HOLDER-CUTTER,C;94-VO
ABS AF-312
1 PAN 420U
KNOB-CUTTER,C;94-VO
ABS AF-312
1 PAN 420U
FRAME-CUTTER
AL6063
1 PAN 421U
SCREW BH; M4*18
SUS
7
BEARING-RADIAL T RUST;NTB 12*26
1
BEARING-RADIAL T RUST;NTB 15*28
4
WIRE-REMOTE;2464 24AWG4C
1
HOLDER-SHAFT,T
S45C
1
SNC3
SENSOR-ASS'Y
2
DU-BUSH ;W/O FLANGE 25*10
2
DU-BUSH ;FLANGE 25*25
4
BUSH-ROLLER,PULL LO
S45C
2
ZWP5
HEATER ASS'Y ;FCHW1 34.5Ω
2
FRAME-SENSOR
AL6063
1 PAN 421U
DU-BUSH ;W/O FLANGE 40*10
4
SCREW BH; M3*14
SUS
4
BAR-IDLE ;φ30
S45C
2
SNC3
PLATE-BEARING;2T
SECC
4
ZWP5
BEARING-IDLE,UP #6201Z
4
BIMETAL HEATER 100℃
2
SHAFT-TABLE;? 10
S45C
1
ZWP5
SPRING-PRESSURE
SWRH φ2.6
4
ZWP5
WASHER-PLAIN 6.6*12.5*1.6
4
BOLT-PRESSURE
SUS M10 P1.5 4
BUSH-ROLLER,PULL UP
S45C
2
ZWP5
BUSH-ROLLER,LAMI UP
S45C
2
ZWP5
ROLLER-PULL,UP ;φ60.0
S45C
1
SNC3
SNAP RING ;STW-15
7
BUSH-PLATE PRESSURE
6
ZWP5
SCREW-SET;M5*15
4
FZB
CAM-ROLLER
S45C
2
ZWP5
SNAP RING ;STW-8
2
BEARING-CAM;#608Z
2
SHAFT-CAM :φ12
S45C
1
ZWP5
PLATE-PRESSURE,R ;3T
SPCC
1
ZWP5
PLATE-PRESSURE,L ;3T
SPCC
1
ZWP5
ROLLER-PULL,LO ;φ60.0
S45C
1
SNC3
DU-BUSH ;FLANGE 40*25
4
BUSH-ROLLER,LAMI LO
S45C
2
ZWP5
ROLLER-LAMI ;φ80.0
S45C
2
SNC3
SPACER-GUIDE
S45C
2
FRAME-GUIDE,PAPER
AL6063
1 PAN. 421U
MOTOR-MAIN;S9D40-24BH(40W 24V)
180:1
1
TAPE TEFLON; 1127* 55mm
1
FRAME-CENTER
AL6063
1 PAN 421U
E-RING ETW-4WON IL
1
WASHER-SPRING φ5.1*1.3T
30
WASHER-PLAIN; 4.3*8*0.8T
5
WASHER-SPRING; φ3.1*0.7T
6
MASH-FRAME,F;2T
SPCC
2 PAN. 421U
FRAME-FRONT;
AL6063
1 PAN. 421U
FRAME-L 4.5T
SPCC
1 PAN. 421U
FRAME-R 4.5T
SPCC
1 PAN. 421U
POWER TRANSFORMER
1
SCREW BH; M5*30
SUS
8
PCB-MAIN ASS'Y
FR4
1
SUPPORT-BRACKET PCB
DASS-9N
8
BRACKET-PCB;1.6T
SECC
1
ZWP5
SCREW FH; M4*8
SUS
15
WASHER-SPRING φ4.1*1.0T
60
FZY
BLOWER ASS'Y
PF-RS6225
2
SCREW BH M4*8
SUS
41
WASHER-SPRING φ6.1*1.5T
4
FZY
BOLT;HEXA HEAD M6*20
8
FZB
FRAME-BASE;
AL6063
1 PAN. 421U
STAND-BASE
STKR 125*50 2
BOLT;HEXA HEAD M8*65
8
FZB
NUT;HEXAGON M8
8
FZY
WASH-SPRING φ8.2*2T
36
BOLT;HEXA HEAD M8*15
28
STAND-CENTER
STKR 125*50 1
STAND-FRAME
STKR 125*50 2
WASHER-SPRING; φ16.2*3.8
4
CASTER-STAND2
20-30S-B3-SBB 2 N,BRAKE
CASTER-STAND1
20-30S-B3-SBB 2
BRAKE
HOLDER ASS'Y-SAFETY COVER
HOLDER ASS'Y-SAFETY COVER
HOLDER ASS'Y-SAFETY COVER
HOLDER ASS'Y-SAFETY COVER
HOLDER-SAFETY COVER
SPROCKET-SLIP IN:P.C.D44, Z=13T
1st GRADE FATAL DEFECT
2nd GRADE FATAL DEFECT
IMPORTA NCE OF QUALITY
0
3rd GRADE MEDIUM DEFECT
0
4th GRADE SLIGHTLY DEFECT
TOTAL
IMPORTANCE OF QUALITY
0
T.I.Q
0
TOTAL
RS H-1050
~6
7 ~ 30
0.08
0.1
31 ~ 120
0.2
121 ~ 300
0.4
301 ~ 600
0.6
601 ~ 1200
0.8
N/S
EXPLODE VIEW
Frame - L
No. Part No.
52
13. Remote Control and Foot Pedal wires.
38
14
16
17
19
24
28
29
40
43
44
45
46
47
48
52
53
54
58
60
78
82
83
90
96
102
105
119
122
131
132
133
134
135
136
140
141
142
186
187
190
192
210
215
216
217
219
MBC04008D2
WSB04010D2
MFC04008D2
23200X001A
013LR2020A
WPB04008D2
WSB05013D2
141LR2003A
122CR4002A
RC000800C8
124LR4002A
SKE05015D2
122LR4004A
RC001500C8
111LR4014A
WPB06016A6
138LR4008A
141LR4012A
MPC03014D2
NHB03024D2
32500X0005
36600X002A
141LR4010A
141LR4011A
142LR4001A
MBC05010D2
021LR2003A
NHB05038D2
141LR4007A
36400X002A
36400X001A
23300X001A
380CR4005A
MBC04040D2
021LR2001A
032LR4008A
MBC04006D2
36400X014A
141LR4015A
SKE04010D2
141LR4015B
138LR4014A
141LR4024A
010LR4001A
141LR4023A
350LR4002A
Part Name
SCREW BH
WASHER-SPRING
SCREW FH
SUPPORT-B/K PCB
FRAME-L
WASHER-PLAIN
WASHER-SPRING
PLATE-PRESSURE,L
BEARING-CAM
SNAP RING
CAM-ROLLER Cu+Ni+Cr
SCREW-SET
BUSH-PLATE PRESSURE
SNAP RING
BOLT-PRESSURE
WASHER-PLAIN
SPRING-PRESSURE
PLATE-BEARING
SCREW BH
NUT
FUSE-MAIN
FUSE BLOCK
BRACKET-HEATER
BRACKET-HEATER,STOPPER
SPACER-HEATER,BKT
SCREW BH
COVER-TAKE UP,L
NUT
BRACKET-SWITCH,EU
SWITCH-MAIN
SWITCH-EMERGENCY
BUSHING-CORD,EU
POWER CORD -CUL
SCREW BH
COVER-L
SHEET-CUTTER
SCREW BH
SWITCH MICRO-SAFETY COVER
BRACKET-MICRO SWITCH
SCREW-SET
BRACKET-MICRO SWITCH
SPRING-HEATER
BRACKET-ENCODER
ENCODER-LENGTH SENSOR,A
BRACKET-SENSOR PCB
PCB-LENGTH ASS'Y
Frame - R
No. Part No.
130
48
150
39
12
14
16
17
23
27
28
29
41
43
44
45
46
47
48
52
53
54
56
58
70
71
72
79
81
90
96
99
100
102
103
105
106
108
111
112
113
114
115
116
117
118
120
121
122
123
128
129
130
133
136
137
138
139
143
144
146
147
149
150
151
152
154
155
156
157
158
159
160
161
167
185
189
190
191
193
194
195
196
197
198
210
213
BHE06020D2
MBC04008D2
WSB04010D2
MFC04008D2
013LR2021A
WSB03007D2
WPB04008D2
WSB05013D2
141LR2004A
122CR4002A
RC000800C8
124LR4002A
SKE05015D2
122LR4004A
RC001500C8
111LR4014A
WPB06016A6
138LR4008A
363LR4001D
141LR4012A
12200X022A
12200X005A
MBC04018D2
MPC03006D2
RC001000C8
141LR4010A
141LR4011A
138LR4002A
125LR4001A
142LR4001A
MBC04010D2
MBC05010D2
MFC04018D2
MBC05018D2
130LR4005A
141LR4006A
138LR4006A
WPB08016A6
141LR4003A
130LR4004A
RE000600D2
21000S027A
021LR2004A
36400X003A
NHB05038D2
112004001C
122LR4006A
134LR4002A
BHE08045D2
36400X001A
MBC04040D2
SKE06010D2
SKE06015D2
SKE05010D2
131LR4004A
131LR4005A
SKE04015D2
131LR4006A
WPB13025A6
112004001B
136LR4002B
136LR4002A
021LR2002A
032LR3004A
032LR4011A
023LR3006A
350LR3007A
144LR4001A
125LR4003A
023LR4001A
147LR4001A
WPB15020A6
12200X025A
SKE04010D2
140LR4005A
140LR4006A
021LR1003A
120LR4003A
131LR4013A
147LR4007A
131LR4014A
138LR4014A
021LR3006A
Part Name
BOLT
SCREW BH
WASHER-SPRING
SCREW FH
FRAME-R
WASHER-SPRING
WASHER-PLAIN
WASHER-SPRING
PLATE-PRESSURE,R
BEARING-CAM
SNAP RING
CAM-ROLLER Cu+Ni+Cr
SCREW-SET
BUSH-PLATE PRESSURE
SNAP RING
BOLT-PRESSURE
WASHER-PLAIN
SPRING-PRESSURE
BIMETAL-HEATER
PLATE-BEARING
BEARING-RADIAL TRUST
BEARING-RADIAL TRUST
SCREW BH
SCREW PH
SNAP RING
BRACKET-HEATER
BRACKET-HEATER,STOPPER
SPRING-FILM,TENSION
HANDLE-TENSION
SPACER-HEATER,BKT
SCREW-BH
SCREW BH
SCREW FH
SCREW BH
GEAR-TAKE UP
PLATE-SLIP
SPRING-SLIP
WASHER-PLAIN
BRACKET-MOTOR
GEAR-MOTOR
E-RING
MOTOR-AC
COVER-TAKE UP,R
SWITCH-POWER
NUT
NUT
BUSH-PULLEY
PULLEY-CHAIN
BOLT
SWITCH-EMERGENCY
SCREW BH
SCREW-SET
SCREW-SET
SCREW-SET
SPROCKET-MOTOR
SPROCKET-ROLLER,LAMI
SCREW-SET
SPROCKET-ROLLER,PULL
WASHER-PLAIN
NUT
CHAIN-ROLLER
CHAIN-ROLLER
COVER-R
SHEET-FUNC
SHEET-PRESSURE-CUL
BUTTON-FUNC
PCB-SUB ASS'Y
CLAMPER-LEVER
LEVER-PRESSURE
KNOB-LEVER
PAD-SLIP
WASHER-PLAIN
BEARING-SLIP
SCREW-SET
HOLDER-SLIP
HOLDER-SLIP(IN)
COVER-TAKE UP,2
SHAFT-SLIP
SPROCKET-SLIP
PAD-SLIP
SPROCKET-SLIP(IN)
SPRING-HEATER
BRACKET-CLAMP LEVER
Stand Part and Frame - Base
No. Part No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
22
26
27
33
69
162
163
164
165
166
176
224
40
13500X001A
13500X002A
WSB16038D0
212LR1003A
212LR1005A
BHE08015D2
WSB08020D2
NHB08065D2
BHE08065D2
212LR1004A
013LR2016A
BHE06020D2
WSB06015D2
MBC04008D2
211003002B
WSB04010D2
141LR3001B
23200X001A
350LR3006D
34000S008A
214LR3003A
WSB03007D2
21000S019A
381LR4032A
1PC03006D2
365LR4003A
025LR4001A
350CR4001A
23300X008A
141LR3004A
31300S002A
Part Name
CASTER-STAND1
CASTER-STAND2
WASHER-SPRING
STAND-FRAME
STAND-CENTER
BOLT
WASHER-SPRING
NUT
BOLT
STAND-BASE
FRAME-BASE
BOLT
WASHER-SPRING
SCREW BH
BLOWER-ASS'Y
WASHER-SPRING
BRACKET-PCB
SUPPORT-B/K PCB
PCB-MAIN ASS'Y
POWER TRANSFORMER
MASH-FRAME,F
WASHER-SPRING
MOTOR-MAIN
WIRE-REMOTE
SCREW TAP TATE PH
SWITCH-FOOT ASS'Y
CASE-REMOCON ASS'Y
PCB-REMOCON ASS'Y
CABLE GRAND
BRACKET-STAND
OPTICAL FIBER AMP
Frame, Roller and Other View
No. Part No.
14
16
17
21
23
24
25
29
31
32
34
35
36
37
38
39
42
49
50
51
55
57
59
61
62
63
64
65
66
67
68
70
72
73
74
75
76
77
78
79
84
85
87
88
93
94
95
104
105
148
153
199
200
201
202
203
211
221
223
41
MBC04008D2
WSB04010D2
MFC04008D2
MBC05030D2
013LR2021A
013LR2020A
013LR2009A
WSB05013D2
013LR2017A
24000X003B
013LR2013B
142LR4002A
133LR2012A
122LR4008A
12200X012A
133LR2014A
120LR3001A
133LR2013A
122LR4007A
122LR4009A
120LR4001A
12200X016A
015LR3006A
12200X014A
013LR2012A
223LR2005B
122LR4010A
12200X013A
12200X015A
313LR3001A
140LR4002A
12200X022A
MBC04018D2
013LR3002A
023LR3003A
140LR3001A
213LR4001A
138LR4001A
NHB03024D2
MPC03006D2
021LR3003A
021LR3004A
381LR4027A
TFH04035D2
141LR4005A
140LR4001A
147LR4002A
141LR4009A
MBC05010D2
SKE04008D2
011LR2004A
140LR4003A
140LR4004C
140LR4004B
140LR4004A
140LR4004D
141LR4036A
140LR4007A
31400S001A
Part Name
SCREW BH
WASHER-SPRING
SCREW FH
SCREW BH
FRAME-R
FRAME-L
FRAME-FRONT
WASHER-SPRING
FRAME-CENTER
TAPE-TEFLON
FRAME-GUIDE,PAPER
SPACER-GUIDE
ROLLER-LAMI
BUSH-ROLLER,LAMI LO
DU-BUSH
ROLLER-PULL,LO
SHAFT-CAM
ROLLER-PULL,UP
BUSH-ROLLER,LAMI UP
BUSH-ROLLER,PULL UP
SHAFT-TABLE
BEARING-IDLE,UP
BAR-IDLE
DU BUSH
FRAME-SENSOR
HEATER ASS`Y
BUSH-ROLLER,PULL LO
DU BUSH
DU BUSH
SENSOR-ASS'Y
HOLDER-SHAFT,T
BEARING-RADIAL TRUST
SCREW BH
FRAME-CUTTER
KNOB-CUTTER,C
HOLDER-CUTTER,C
CUTTER-CROSS
SPRING-CROSS,CUTTER
NUT
SCREW PH
CASE-SENSOR,UP
CASE-SENSOR,LO
WIRE-SENSOR
SCREW FH
PLATE-SHAFT,FILM
HOLDER-SHAFT,FILM
PAD-TENSION
BRACKET-REAR COVER
SCREW BH
SCREW-SET
COVER-REAR
HOLDER-SAFETY COVER
HOLDER ASS'Y SAFETY COVER
HOLDER ASS'Y SAFETY COVER
HOLDER ASS'Y SAFETY COVER
HOLDER ASS'Y SAFETY COVER
BRACKET-SENSOR
HOLDER-SENSOR COUNT
OPTICAL FIBER CABLE
Wire and Film Shafts
No. Part No.
1
2
3
180
4
181
182
42
48
80
81
86
89
91
92
97
101
109
139
168
169
170
171
172
173
174
175
177
178
179
180
181
182
183
184
212
214
218
220
222
RC001500C8
12200X002A
RC001000C8
381LR4035B
111LR4004A
120LR3004A
143LR3001A
12200X009A
124LR3001A
120LR4002A
SKE05010D2
123004001A
381LR4020B
381LR4029B
381LR4030B
381LR4013A
381LR4042B
381LR4047B
381LR4044A
381LR4043A
381LR4045B
381LR4046A
381LR4048A
381LR4054A
381LR4055A
381LR4036A
381LR4037A
120LR3003A
125LR4002A
143LR4001A
111LR4005A
143LR3002A
Part Name
SNAP RING
DU BUSH
SNAP RING
WIRE-MOTOR
BOLT-CORE
SHAFT-FILM,LO
SUPPORTER-SHAFT,LO
DU BUSH
CORE-57
SHAFT-TAKE UP
SCREW-SET
BALL
WIRE-FUSE,EU
WIRE-LO HEATER,EU
WIRE-UP HEATER,EU
WIRE-POWER S/W,EU
WIRE-EMER 2
WIRE-EMER
WIRE-MAIN
WIRE-SAFETY SWITCH
WIRE-LENGTH
WIRE-COUNT
WIRE-TAKE UP2
WIRE-LO HEATER 2,EU
WIRE-UP HEATER 2,EU
WIRE-T/FUSE,UP
WIRE-T/FUSE,LO
SHAFT-FILM,UP
HANDLE-LOCATION
STOPPER-LOCATION
BOLT-LOCATION,ADJUST
SUPPORTER-SHAFT,UP
Front Table and Safety Cover
209
No. Part No.
14
28
30
124
125
126
127
142
145
188
204
205
206
207
208
209
43
MBC04008D2
WPB04008D2
RE000400D2
014LR1003A
145LR3001A
111LR4006A
023LR4002A
MBC04006D2
NHB04032D2
141LR4022E
013LR4002A
021LR3005B
141LR4022B
013LR4001A
111LR4009A
138LR4010A
Part Name
SCREW BH
WASHER-PLAIN
E-RING
TABLE-FRONT
GUIDE-DOCUMENT
BOLT-GUIDE
KNOB-BOLT,GUIDE
SCREW BH
NUT
BRACKET-SAFETY COVER
SAFETY COVER FRAME-L
SAFETY COVER
BRACKET-SAFETY COVER
SAFETY COVER FRAME-R
BOLT- SAFETY COVER
SPRING-SAFETY COVER
8. RSH-1650/1050 Wiring Diagram
RSH-1650/1050 Wiring Diagram
18 ~ 22
44
< RSH-1650/1050 Main PCB Layout >
⑬
④
⑤
⑧
1. Wire Main.
2. Wire Sensor Up
3. Wire Sensor Low
4. Wire Count
5. Wire Length
6. Wire Power
7. Wire Low Heater
⑥
POWER TRANSFORMER
③
①
②
⑪
⑦
MCU
⑨
⑩
⑫
<Connect part>
8. Wire Up Heater.
9. Wire Blower(3EA)
10. Wire Take Up
11. Power Transformer wires
12. Motor wires
13. Remote Control and Foot Pedal wires.
14. Wires Output Transformer
45
⑭
<SUB PCB and Frame-R Heater Layout>
<Length Layout>
Wire Up Heater
Wire Main
Counter Sensor Wire
Bimetal
(100℃)
PCB SUB
Wire Low Heater
46
<Main S/W and Count Layout>
<Micro S/W and Frame-L Heater Layout>
PCB Length
Wire T/Fuse (110℃)
Safety Cover Micro S/W
Switch Main
Wire T/Fuse (104°C)
Main Fuse
47
Frame Guide Paper
Micro S/W